7x Pair Universal Measuring Attachments Flat Round Disc Cutting Point Thin Blade Edge - Microtech Metrology
€299.00
Product information "7x Pair Universal Measuring Attachments Flat Round Disc Cutting Point Thin Blade Edge - Microtech Metrology"
Take advantage of a compact, versatile accessory set that expands measuring capability with seven pairs of tip geometries, optimised for universal outside micrometers; the combination of variety and precise contact surfaces supports efficient measurement workflows. Order or request advice via Metav Werkzeuge for fast procurement and application support.
Universal Measuring Attachment Set — 7 pairs for universal outside micrometers by Microtech Metrology
Universal Measuring Attachment Set is a compact accessory kit designed to adapt universal outside micrometers for a wide range of contact geometries in workshop and laboratory environments.
- Seven pairs of tip geometries
- Compatible with universal outside micrometers
- Precision contact surfaces for repeatable readings
- Versatile set for inspections and small-batch metrology
Extend measurement reach with tailored tip geometries
The set supplies seven pairs of interchangeable contacts—flat, round, disc, cutting edge, pointed, thin and knife‑edge—so standard micrometers can be adapted quickly for specific tasks. By replacing the contact face rather than switching instruments, inspection loops remain short and cycle times are reduced. The variety of tip shapes supports precise positioning on shafts, edges, recesses and thin webs, improving repeatability and reducing setup time in series inspection.
Improve workflow reliability with consistent contact surfaces
Each attachment is produced for consistent contact behaviour, which helps to minimise operator‑dependent variation when measuring. Where surface form or access is challenging, the nominal contact geometry determines the contact area and pressure distribution; selecting the correct tip reduces measurement error and preserves the reference standard. The result is a measurable uplift in quality assurance efficiency and fewer rejected parts due to ambiguous readings.
Simple handling and clear inventory for the workshop
The set groups seven distinct contact pairs in one delivery, making it straightforward to maintain an inventory of common geometries for micrometer testing and part verification. Compatibility with universal outside micrometers means there is no need for tool‑specific conversion kits. Clear labelling of each pair speeds selection during bench checks and helps standardise measurement procedures across shifts and operators.
Contact Metav Werkzeuge to request the Microtech Metrology Universal Measuring Attachment Set (SKU 110750100) or to discuss the right tip choice for specific applications; Metav Werkzeuge is available at info@metav-werkzeuge.com or +49 2822 7131930 for tailored advice
Technical data
- Article number: 110750100
- GTIN: 4061905458392
- Manufacturer: Microtech Metrology
Facts
- Pairs in set: 7
- Items per set: 7 pairs
Special features
- Flat, round, disc, cutting edge, pointed, thin, knife‑edge contacts
- Suitable for universal outside micrometers
- Accessory for measurement and inspection tasks
FAQ
Which micrometers are compatible with these attachments?
The attachments are designed for use with universal outside micrometers; compatibility is confirmed for standard thread mountings and contact adaptors used in bench micrometers supplied by Microtech Metrology (SKU 110750100).
What contact geometries are included in the set?
The set contains seven pairs: flat, round, disc, cutting edge, pointed, thin and knife‑edge, supplied to extend the functionality of universal outside micrometers for varied measurement tasks.
Can the attachments affect measurement accuracy?
Attachments alter the contact geometry and therefore the contact area; using the correct tip from the Microtech Metrology set helps to reduce measurement variability and improve the repeatability of readings with universal outside micrometers.
Is this set suitable for in‑process inspection on production lines?
Yes. The array of contact types in the Microtech Metrology set makes it suitable for rapid changeover during short inspection cycles and for small‑batch quality checks where different part geometries occur.
How many pieces are supplied in one set?
One set contains seven pairs of measuring attachments (total seven pairs), referenced under SKU 110750100.
Microtech Metrology: Manufacturer / Responsible: Microtech, Nizhneyurkovska str., 45a, 04080 Kyiv, Ukraine, tool@microtech.tools
Passend für
Benefit from high‑precision measurement combined with modern data transfer and modular tooling: the instrument’s 0.003 mm accuracy and Wireless and USB data output speed up inspection cycles and reduce transcription errors, while the interchangeable anvils enable flexible measurement set‑ups. Order directly via Metav Werkzeuge or consult the on‑site specialists for configuration and supply. Universal micrometer – digital bench micrometer, 0–40 mm range, Wireless + USB (Microtech Metrology) The Universal micrometer offers a compact, digital measuring solution for precise external and step measurements in workshop and production environments. Digital micrometer, 0.003 mm accuracy 0–40 mm measuring range Wireless and USB data output Interchangeable anvils (anvils not included) Precision that shortens inspection time The instrument delivers 0.003 mm accuracy, providing repeatable results for tight tolerances typical in precision engineering and quality control. With a 0–40 mm measuring range and 0.0001 mm resolution on the display, the device is suitable for small components where micrometre‑level deviations are critical. A 18 mm measuring depth supports measurements on stepped parts and constrained geometries, reducing the need for secondary fixtures and saving inspection time. Integrating measurement into the production flow Equipped with Wireless and USB data output, the device removes manual transcription and enables direct capture into inspection software or SPC systems. The digital interface supports faster batch documentation and traceability, which improves process transparency and lowers administrative overhead. Where consistent data logging is required, wireless transfer speeds up throughput and reduces human error without altering established workflows. Modular anvils for diverse measuring tasks The micrometer accepts interchangeable anvils, allowing adaptation to different workpiece shapes and contact radii; this modularity increases versatility across jobs without requiring multiple instruments. Note that anvils are not included with delivery, which makes it straightforward to select the appropriate anvil geometry for each application. The modular approach supports rapid changeovers and reduces inventory of distinct gauges. Robust design for shopfloor use Built as a workshop instrument, the device balances precision with practicality: a compact form factor and durable construction stand up to daily handling in machine shops and inspection benches. The combination of precise measurement capability and straightforward data export makes the tool well suited for toolmakers, service providers and in‑line quality checks. Microtech Metrology’s engineering ensures the unit integrates into existing measuring routines while delivering measurable gains in efficiency and reliability. Contact Metav Werkzeuge to discuss the best Universal micrometer configuration for specific applications or to confirm current stock in Emmerich — email info@metav-werkzeuge.com or call +49 2822 7131930 Technical data SKU: 115050477 GTIN: 4061905457722 Manufacturer: Microtech Metrology Measuring range: 0–40 mm Data output: Wireless + USB Digital: yes Numbers / Core technical data Accuracy: 0.003 mm Display resolution: 0.0001 mm Measuring depth: 18 mm Measuring range min/max: 0 / 40 mm ECLASS: 21170328 Special features / Versions Interchangeable anvils — anvils not included Suitable for external and step measurements Digital data transfer for SPC integration Compact bench body for workshop use FAQ Is the micrometer suitable for routine incoming inspection? The Universal micrometer from Microtech Metrology (SKU 115050477) is designed for routine inspection work with 0.003 mm accuracy, making it suitable for incoming quality checks on small components. How is measurement data transferred to a PC? Data transfer is handled via the unit’s Wireless and USB interfaces; the Universal micrometer supports direct export to inspection software or data loggers for downstream analysis. Are the measuring anvils included with the delivery? The delivery does not include anvils; the Universal micrometer accepts interchangeable anvils, which can be selected separately to match the required contact geometry. What kinds of measurements can be performed with this instrument? The device is optimised for external and step measurements on small parts; its 18 mm measuring depth and compact frame suit stepped components and confined geometries. Can the micrometer be used on the shopfloor in continuous production? Yes. The digital output and robust construction make the micrometer appropriate for repeated use in production environments where rapid documentation and reliability are needed. Manufacturer / Responsible: Microtech, Nizhneyurkovska str., 45a, 04080 Kyiv, Ukraine, tool@microtech.tools