140mm 25 x 25 Side Turning Tool Carbide P25/P30, Offset, DIN 4980 (ISO 6) - Werner Wilke Zerspanungstechnik GmbH

Take advantage of the combination of an offset shank, carbide P25/P30 cutting plates and DIN 4980 compatibility for reliable, precise external turning operations; order directly via Metav Werkzeuge or contact our advisors for specification support.

Side-turning tool DIN 4980 (ISO 6), 25 x 25 mm, carbide P25/P30 by Werner Wilke

The side-turning tool DIN 4980 (ISO 6) 25 x 25 mm is an offset, right-hand external turning tool designed for use in standard DIN 4980 (ISO 6) toolholders, suitable for precision lathe operations.

• Carbide P25/P30 inserts fitted
• Offset shank for clearance
• DIN 4980 (ISO 6) shank form
• 25 x 25 mm cross-section

Precision external turning with robust carbide inserts

The side-turning tool combines a steel shank with diamond-ground carbide cutting plates in grade P25/P30, yielding consistent cutting edges and predictable wear characteristics. The diamond grinding on the inserts improves surface contact and reduces the need for frequent adjustment, which translates into shorter setup times and steadier part finish during batch production. With an overall length of 140 mm and a clear 25 x 25 mm cross-section, the tool suits standard holders while offering the rigidity required for moderate to demanding external turning. The right-hand cutting direction is specified for typical lathe feed directions and avoids ambiguity during tool selection.

Seamless compatibility with DIN 4980 toolholders

Designed to the DIN 4980 (ISO 6) shank form and presented as an offset (abgesetzt) variant, the tool integrates directly with widely used lathe toolposts and indexable systems that accept this standard. Compatibility with the DIN 4980 standard simplifies procurement and replacement planning in production environments where interchangeability is essential. The offset geometry provides the necessary clearance between the cutting edge and workpiece shoulders or fixtures, reducing the risk of collision and enabling easier access to stepped profiles or close-to-flange turning tasks. The combination of standardised shank form and defined cross-section supports stable clamping and repeatable tool resets.

Built for repeatable production and ergonomic handling

A steel shank fitted with replaceable, diamond-ground carbide plates keeps maintenance straightforward: worn inserts can be exchanged without replacing the entire toolholder. The tool’s construction supports consistent repeatability in serial production, helping to reduce scrap and rework. Its format and balance aid in operator handling when mounting or changing tools, and the defined cross-section (25 x 25 mm) provides a robust contact surface in the toolholder, limiting vibration and enhancing surface finish. These attributes make the tool a pragmatic choice for workshops seeking durable, easy-to-service turning solutions.

Material guidance and application overview

The cutting plates are specified as carbide P25/P30, industrial grades suited to a broad range of turning tasks on steels and similar materials. The designation indicates a robust carbide grade intended for general steel machining operations while maintaining edge stability; diamond grinding improves chip control and edge conformity. As a right-hand, offset side-turning tool, it is optimised for conventional lathe feeds and external profiling; however, compatibility with specific steels, alloys or advanced materials depends on cutting parameters, insert geometry and machine rigidity. For tailored setup recommendations and cutting data, technical consultation is available to match tool grade and machining strategy to the intended application.

For precision external turning with proven carbide inserts, request availability from Metav Werkzeuge and benefit from expert selection and fast supply from Emmerich.

Technical data

• Article number: 4118640252NW
• Manufacturer: Werner Wilke Zerspanungstechnik GmbH

Facts

• Overall length: 140 mm
• Cross-section: 25 x 25 mm
• Packaging unit: 3

Special features

• Carbide: P25/P30
• Offset shank (abgesetzt)
• DIN 4980 (ISO 6) shank form
• Steel shank fitted with diamond-ground carbide inserts
• Right-hand cutting

FAQ

What material are the cutting plates made of?
The cutting plates are manufactured from carbide P25/P30, supplied on the side-turning tool by Werner Wilke Zerspanungstechnik GmbH for stable cutting performance.

Is this tool compatible with DIN 4980 toolholders?
Yes, the tool follows the DIN 4980 (ISO 6) shank form, ensuring compatibility with holders that accept this standard shank profile.

What are the dimensions and form of the tool shank?
The side-turning tool has a 25 x 25 mm cross-section and an overall length of 140 mm, provided in an offset form for improved clearance.

Can the cutting plates be replaced?
The tool uses replaceable, diamond-ground carbide inserts in grade P25/P30, allowing replacement of worn plates without removing the shank from the machine.

Is this tool suitable for left-hand turning tasks?
This specific tool is specified as right-hand cutting; for left-hand operations a corresponding left-hand variant should be selected.

Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com