100mm 12 x 12mm Side Turning Tool Carbide P25/P30, Right-Hand, DIN 4980 (ISO 6) - Werner Wilke Zerspanungstechnik GmbH
Take advantage of the offset design, carbide P25/P30 cutting plates and the compact 12 x 12 mm cross-section for reliable right-hand turning in tight fixtures — order the side-turning tool directly via Metav Werkzeuge or request guidance from the consultants if required. Side-turning tool »Wilke« – DIN 4980 (ISO 6), 12 x 12 mm, carbide P25/P30, right-hand Side-turning tool for industrial turning tasks; an offset holder compliant with DIN 4980 (ISO 6) tailored to right-hand machining in confined set-ups. Carbide P25/P30 for long tool life Right-hand cutting for turning tasks 12 x 12 mm square cross-section Offset design for restricted access Consistent accuracy thanks to standardised interface and geometry The holder adheres to DIN 4980 (ISO 6), ensuring a standardised mounting and repeatable alignment across compatible toolposts. The 12 x 12 mm square cross-section provides a stable contact surface that reduces vibration and runout, which improves dimensional consistency on serial turned parts. For production environments this means predictable tool behaviour and fewer rejects. Durable cutting performance from high-grade carbide Equipped with carbide plates in P25/P30 grades, the assembly offers high wear resistance under typical machining loads. The choice of P25/P30 balances toughness and hardness for standard turning operations, resulting in sustained cutting edges and less frequent regrinding. Diamond‑ground surfaces on the cutting plates produce a clean initial edge, contributing to consistent surface finish and extended service intervals. Practical offset geometry for confined and stepped work The offset (abgesetzt) profile of the holder creates clearance for operations near shoulders or recessed features, allowing access where straight shanks would collide. With a compact 100 mm overall length, the tool combines reach with rigidity, making it suitable for medium-reach applications in toolrooms and production workshops that require both accessibility and control. Built for ease of assembly and predictable results The tool is supplied as a steel shank fitted with precision, diamond-ground cutting plates, reducing set-up time and ensuring a uniform cutting edge orientation. The standardised interface simplifies replacement routines and minimises machine downtime, supporting lean workshop processes where consistent cycle times and uptime are valued. Suitable for workshop and small-batch production environments Designed for machinists and maintenance engineers who demand reliable right-hand turning in compact fixtures, this turning holder supports efficient workflows without complex set-up procedures. The combination of standard conformity, robust cutting material and offset geometry addresses common bottlenecks in small-batch production and maintenance turning tasks. Discuss suitability with Metav Werkzeuge for application-specific advice or to secure compatible holders and inserts directly from our warehouse in Emmerich Technical data Article number: 4118640102NW Label: Seitendrehmeißel DIN 4980ISO6 12x12mm HM P25/P30 re. Wilke Product type: Seitendrehmeißel Manufacturer: Werner Wilke Zerspanungstechnik GmbH Data Overall length: 100 mm Cross-section: 12 x 12 mm Form: abgesetzt Standard: DIN 4980 (ISO 6) Cutting direction: right Special features Material: carbide P25/P30 Steel shank with diamond-ground carbide cutting plates fitted Offset design for restricted access SKU: 4118640102NW FAQ What is the standard interface of the turning holder? The holder conforms to DIN 4980 (ISO 6), ensuring compatibility with toolposts and fixtures designed for that shank profile. Which cutting material is fitted on the tool? The assembly is fitted with carbide P25/P30 cutting plates; these are diamond-ground for an accurate cutting edge and sustained wear resistance. Is this a right-hand or left-hand tool? This is a right-hand turning tool, specified for conventional right-hand cutting directions and applications. What are the key dimensions to check before purchase? Check the 12 x 12 mm cross-section and the 100 mm overall length to ensure the holder fits the intended toolpost and reaches the workpiece as required; SKU 4118640102NW identifies this configuration. Can this holder be used for confined shoulder turning? Yes, the offset design provides additional clearance for shoulders and recessed features, improving accessibility in confined turning tasks. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
100mm Bent Turning Tool Carbide P25/P30 Left-Hand DIN 4972 (ISO 2) - Werner Wilke Zerspanungstechnik GmbH
Take advantage of the combination of carbide P25/P30 durability, a bent DIN 4972 (ISO 2) geometry for improved access, and a robust 12 x 12 mm cross-section to maintain consistent turning performance; order the tool directly via Metav Werkzeuge or consult our specialists for integration advice. Wilke bent carbide turning tool 12 x 12 mm (left-hand) – DIN 4972 (ISO 2) A Wilke bent carbide turning tool for precision external turning and confined-access operations, supplied with diamond-ground carbide inserts for fine surface finish. Carbide grades P25/P30 for wear resistance Bent geometry to DIN 4972 (ISO 2) for reach 12 x 12 mm compact cross-section Left-hand cutting direction for reversing operations Precision and endurance through carbide engineering The bent tool offers a compact geometry that combines stability and access, making it suitable where straight holders obstruct the machining path. Manufactured with cemented carbide P25/P30, the tool provides enhanced wear resistance and predictable edge life under steady cutting conditions. The diamond-ground cutting faces ensure a consistent surface quality on turned components while reducing the need for frequent edge reshaping, supporting continuous production runs and predictable maintenance cycles. Geometry that improves reach and process reliability With a bent DIN 4972 (ISO 2) profile and a 12 x 12 mm cross-section, the design reduces interference in tight set-ups and allows safer clearance near shoulders and collars. The left-hand cut orientation enables operations where the workpiece rotation and feed direction demand reverse cutting geometry. The steel shank construction contributes to torsional rigidity, while the bent form helps maintain cutting stability, reducing chatter and improving dimensional repeatability for serial turning tasks. Application-focused benefits and straightforward integration Equipped with diamond-ground carbide inserts mounted on a steel shank, the tool supports fine finishing passes as well as routine external turning sequences. The standard compliance with DIN 4972 (ISO 2) simplifies holder selection and ensures compatibility with common toolpost and turret systems, enabling rapid adoption into existing CNC or manual lathe workflows. Consistent insert geometry contributes to predictable cutting forces and reduced cycle-time variability, which benefits process planning and quality control. Practical handling, packaging and inventory considerations Supplied in a packaging unit of 5, the tool is easy to store and rotate within a small-tool inventory strategy. The compact 100 mm overall length and the square cross-section simplify holder clamping and replacement during set-up changes. Identification by SKU 4118605552NW allows straightforward ordering and inventory tracking; the tool’s standardised dimensions and material specification support reproducible set-ups and minimise procurement complexity for production planners. Contact Metav Werkzeuge in Emmerich at info@metav-werkzeuge.com or +49 2822 7131930 to confirm fitment, delivery options and suitability of the Wilke bent carbide turning tool for specific turning operations Technical data Article number: 4118605552NW Label: Drehmeißel DIN 4972ISO2 12x12mm HM P25/P30 li. geb. Wilke Product type: Turning tool Facts Cross-section: 12 x 12 mm Overall length: 100 mm Packaging unit: 5 Special features Material: cemented carbide P25/P30 Form: bent (gebogen) Standard: DIN 4972 (ISO 2) Cutting direction: left-hand Steel shank fitted with diamond-ground carbide inserts FAQ What materials is the tool intended for? The Wilke bent carbide turning tool is specified with cemented carbide P25/P30 inserts, providing general-purpose durability for typical external turning applications; specific material compatibility should be confirmed against cutting parameters. Is the tool compatible with standard DIN 4972 holders? Yes. Compliance with DIN 4972 (ISO 2) ensures compatibility with standard holders designed for that profile, simplifying integration into existing toolposts and turrets. How does the left-hand cutting direction affect its use? Left-hand cutting means the tool is ground for feeds that require reverse cutting orientation; choose this orientation where the lathe feed and rotation require left-hand tools for correct tool–workpiece engagement. Can the diamond-ground inserts improve surface finish? Diamond-ground cutting faces on the inserts are intended to produce a finer initial surface and more consistent cutting behaviour, which can reduce subsequent finishing steps in many turning operations. What information identifies the exact article for ordering? Order or reference the tool by SKU 4118605552NW and the label supplied, which matches the Wilke bent carbide turning tool specification. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
100mm External Threading Tool 10x10mm Carbide P25/P30 60° Right-Hand WN282 - Werner Wilke Zerspanungstechnik GmbH
Take advantage of the combination of carbide P25/P30 reliability and a precise 60° profile for consistent external thread turning; the compact 10 x 10 mm cross-section and 100 mm length ensure stable mounting and repeatable results. Order directly via Metav Werkzeuge or consult our specialists for compatibility details. External thread turning tool 10 x 10 mm, carbide P25/P30, 60° (right-hand) – Werner Wilke External thread turning tool 10 x 10 mm, carbide P25/P30 for right-hand 60° thread profiles on lathes and turning centres Carbide grade P25/P30 for wear resistance 60° profile for standard external threads 10 x 10 mm compact cross-section Diamond-ground carbide cutting plates Consistent cutting performance and extended tool life The combination of carbide P25/P30 and diamond-ground cutting plates delivers a robust mix of hardness and toughness that preserves the cutting edge under repeated use. This construction reduces flank wear and maintains a precise thread form over longer runs, which translates into fewer tool changes and more predictable cycle times. The 60° geometry ensures compatibility with ISO metric and many standard thread forms, helping to uphold tolerance requirements without frequent rework. Stable clamping and accurate thread form control A compact 10 x 10 mm cross-section paired with an overall length of 100 mm provides a stable mounting geometry in standard toolholders and shank adaptors. The steel shank fitted with carbide inserts minimises vibration and improves surface finish by keeping the insert rigid during cut entry and exit. The right-hand cutting direction is optimised for conventional turning operations, offering reliable chipflow and reduced burr formation when used in appropriate turning setups. Practical application and handling benefits Designed for straightforward integration into turning processes, the insert is identified under the WN282 standard for quick selection and replacement. The diamond-ground carbide faces facilitate fine finishing passes and consistent dimensional control of external threads. For workshops aiming to streamline production, this tool supports efficient changeovers and repeatable results, making it suitable for batch production and precision work on conventional and CNC lathes. Contact Metav Werkzeuge today for a compatibility check and fast supply from Emmerich — our Metav IndustryLine specialists will confirm suitability for standard 60° external thread turning and advise on toolholder matching Technical data SKU: 4118650202NW Standard: WN282 Manufacturer: Werner Wilke Zerspanungstechnik GmbH Product type: External thread turning tool Packaging unit: 5 Facts Overall length: 100 mm Cross-section: 10 x 10 mm Tip angle: 60° Cutting direction: right Design / special features Carbide P25/P30 Steel shank with diamond-ground carbide cutting plates 60° thread profile FAQ What materials is this tool intended for? The External thread turning tool 10 x 10 mm, carbide P25/P30 is manufactured with P25/P30 carbide, which provides a good balance of wear resistance and toughness for general turning tasks; specific material suitability should be verified for very hard or specialised alloys. Is the 60° geometry suitable for metric threads? Yes, the 60° profile corresponds to standard metric and many unified thread forms, making the tool appropriate for producing common external threads on lathes. How is the tool identified for reordering? Reorder using SKU 4118650202NW or the WN282 designation; both identifiers are referenced for the External thread turning tool and simplify stock replenishment. Can the carbide inserts be re-sharpened or replaced? The tool features diamond-ground carbide cutting plates mounted on a steel shank; the cutting plates are intended to be replaced rather than resharpened in most workshop scenarios to preserve geometry and thread accuracy. What is the recommended use case for this tool? This product is aimed at external thread turning on conventional and CNC lathes where a compact 10 x 10 mm tool and stable, repeatable 60° thread form are required; it is suited to batch work and production environments seeking consistent results. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
100mm Side Turn Tool 12x12mm Carbide P25/P30 Offset Left DIN 4980 (ISO 6) - Werner Wilke Zerspanungstechnik GmbH
Take advantage of the combination of a carbide P25/P30 cutting edge, a 12 x 12 mm square shank and the standardized DIN 4980 connection for consistent side-turning results; order directly via Metav Werkzeuge or consult the technical team for compatibility and setup advice. Side turning tool DIN 4980 (ISO 6) 12 x 12 mm, carbide P25/P30, left-hand — Werner Wilke Side turning tool DIN 4980 (ISO 6) 12 x 12 mm, carbide P25/P30, left-hand is a stepped steel-shank tool fitted with diamond-ground carbide cutting plates for precise lateral turning operations in standard DIN 4980 toolholders. Carbide P25/P30 cutting plates 12 x 12 mm square shank Left-hand cutting orientation DIN 4980 (ISO 6) interface Durable carbide grade for reliable steel machining The tool is equipped with carbide plates in P25/P30, a grade optimised for common steel applications. The use of diamond-ground cutting plates ensures a consistent cutting geometry and long tool life, which reduces the frequency of regrinding or replacement. As a result, manufacturers and workshops benefit from predictable tool behaviour under repetitive lateral turning tasks, improving process stability and lowering unplanned stoppages. The delivered configuration suits routine finishing and semi-finishing operations where reproducible surface quality matters. Standardised connection and compact geometry for quick integration Conformity with DIN 4980 (ISO 6) means the insert-mounted tool integrates smoothly into compatible toolholders and lathe setups. The 12 x 12 mm cross-section and a stepped design provide a compact, rigid interface that facilitates clamping reproducibility and minimises deflection during side turning. The steel shank construction combines torsional stability with familiar mounting practices in industrial turning cells, enabling fast tool changes and reliable positioning without additional adaptors. Left-hand orientation and handling benefits for specific set-ups Designed as a left-hand lateral turning tool, this variant permits cutting actions when the tool must approach the workpiece from that direction, avoiding awkward re-fixturing or complex tool staging. The diamond-ground plates contribute to consistent chip formation and surface finish, supporting operators who require dependable results on repeat runs. This tool is therefore suited to production lines and job-shop environments where direction-specific operations and short-cycle repeatability are part of the daily workflow. Procurement confidence and practical support from Metav Sourcing through an experienced partner offers both logistical and technical reassurance. Metav’s role as a quality filter for the European market and its broad product range mean access to supplementary tooling and matched holders is straightforward. For customers seeking compatibility checks, mounting advice or batch supply planning, direct contact with Metav Werkzeuge’s consultants helps ensure the chosen side turning tool matches the existing toolholder architecture and production requirements. Contact Metav Werkzeuge to confirm compatibility with existing DIN 4980 toolholders, request a technical datasheet for this left-hand carbide side turning tool (SKU 4118640552NW) or arrange a tailored supply plan via info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: 4118640552NW Product: Side turning tool Label: Seitendrehmeißel DIN 4980ISO6 12x12mm HM P25/P30 li. Wilke Manufacturer: Werner Wilke Zerspanungstechnik GmbH Form: Stepped Standard: DIN 4980 (ISO 6) Facts Cross-section: 12 x 12 mm Overall length: 100 mm Packaging unit: 5 Special features Material: Carbide P25/P30 Steel shank with diamond-ground carbide cutting plates Left-hand cutting direction Stepped (offset) design Conforms to DIN 4980 (ISO 6) FAQ What materials is this side turning tool suited for? The side turning tool with P25/P30 carbide plates is intended primarily for steel machining and typical lateral turning tasks where ISO P-grade carbide is appropriate. How does the DIN 4980 connection affect integration? DIN 4980 (ISO 6) ensures compatibility with standard toolholders; the 12 x 12 mm square shank and stepped format enable straightforward clamping into compatible holders without special adaptors. Is this a left-hand or right-hand tool and why does it matter? This is a left-hand variant; left-hand orientation is required when the cutting approach and lathe setup demand tool movement from the opposite direction to a right-hand tool. What advantages do diamond-ground plates provide? Diamond-ground carbide plates deliver a consistent cutting edge and improved surface finish, which supports more predictable tool life and reproducible machining results. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
100mm Turning Tool 12x12mm Carbide P25/P30 Bent Right-Hand DIN 4972 (ISO 2) - Werner Wilke Zerspanungstechnik GmbH
Take advantage of a bent, carbide-tipped turning tool that combines standard conformity and compact dimensions for dependable workshop performance; its diamond-ground carbide plates and 12 x 12 mm cross-section ensure repeatable results and simple toolholder compatibility. Order via Metav Werkzeuge or request further specification support from our technical advisors. Drehmeißel DIN 4972 (ISO 2) 12x12mm HM P25/P30 – Bent, right-hand turning tool by Werner Wilke The Drehmeißel DIN 4972ISO2 12x12mm HM P25/P30 re. geb. Wilke is a bent turning tool designed for standardised lathe operations, offering a compact 12 x 12 mm cross-section and a 100 mm overall length for versatile mounting in conventional tool posts. Carbide P25/P30 cutting plates Bent shank for versatile turning DIN 4972 (ISO 2) standard 12 x 12 mm cross-section, 100 mm length Consistent cutting performance through carbide tip technology The bent turning tool is fitted with carbide P25/P30 cutting plates that are diamond-ground to a precise edge geometry. This configuration reduces tool wear variability and supports stable cutting conditions across repeated cycles. Compliance with DIN 4972 (ISO 2) gives machinists a verifiable baseline for mounting and use, which simplifies process planning in jigs and fixtures. With a focus on measurable performance, the assembly minimises vibration at the cutting point and helps maintain dimensional tolerances during serial production runs. The use of a hardened carbide specification provides predictable edge life, which makes scheduling of tool changes and inspection intervals straightforward. Practical design for easy integration and reliable clamping A steel shank fitted with replaceable carbide plates combines the rigidity of a solid holder with the serviceability of tipped tools. The tool’s bent form permits access to turning profiles that are difficult to reach with straight holders, while the right-hand cutting orientation aligns with common lathe setups. The 12 x 12 mm cross-section and 100 mm overall length were selected to balance stiffness and clearance, ensuring compatibility with standard toolholders and straightforward set-up. The small package size and the packaging unit of 5 support stock management for workshops that require immediate replacements without overstocking. Application clarity and procurement advantages for workshops This turning tool is intended for standardised turning operations where a compact tipped tool is preferred. The combination of a bent holder and diamond-ground carbide plates supports finishing and light-to-medium turning tasks that demand consistent edge geometry and quick replacement of cutting edges. For production environments aiming for predictable throughput, the tool’s conformity to an established standard simplifies quality documentation and supplier communication. Sourcing through a reliable distributor ensures availability and traceability of the item by its article number and specification, aiding inventory control and batch documentation. For specification advice or availability of this Werner Wilke turning tool, contact Metav Werkzeuge for prompt technical support and local stock information at info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: 4118605102NW Label: Drehmeißel DIN 4972ISO2 12x12mm HM P25/P30 re. geb. Wilke Brand: Werner Wilke Zerspanungstechnik GmbH Facts Overall length: 100 mm Cross-section: 12 x 12 mm Packaging unit: 5 Conforms to: DIN 4972 (ISO 2) Special features Material: Carbide P25/P30 Bent design Steel shank with diamond-ground carbide cutting plates Right-hand cutting FAQ What is the article number for this turning tool? The article number is 4118605102NW for the turning tool by Werner Wilke. Which standard does the tool follow and why does that matter? The tool conforms to DIN 4972 (ISO 2), which facilitates compatibility with standard toolholders and supports consistent mounting and dimensional control. What carbide grade is used for the cutting plates? The cutting plates are carbide P25/P30, diamond-ground for consistent edge geometry and predictable wear characteristics. Is the holder straight or bent and what advantage does that give? The holder is bent, allowing access to profiles and geometries that are harder to reach with straight holders and improving clearance in certain setups. How many items are supplied per packaging unit? The packaging unit contains 5 pieces. Manufacturer: Werner Wilke Zerspanungstechnik GmbH; Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
100mm Turning Tool 12x12mm Straight Broad Carbide P25/P30, DIN 4976 (ISO 4) - Werner Wilke Zerspanungstechnik GmbH
Take advantage of a robust carbide grade and a broad, DIN‑compliant profile to maintain a steady production rhythm with reduced changeovers; order this turning tool directly via Metav Werkzeuge or consult the Metav team for tailored guidance. Turning tool DIN 4976 (ISO 4) 12 x 12 mm, carbide P25/P30 — Wilke The Turning tool DIN 4976 (ISO 4) 12 x 12 mm, carbide P25/P30 is a straight, broad‑profile lathe tool designed for stable, repeatable turning operations where rigidity and wear resistance are priorities Carbide grade P25/P30 for high wear resistance 12 x 12 mm square cross‑section for ISO 4 holders Broad profile for increased rigidity and cutting stability Steel shank with diamond‑ground carbide cutting plates Longer tool life through optimised carbide selection The combination of carbide in grade P25/P30 and a broad profile gives noticeably extended service intervals compared with conventional tool geometries. The chosen grade balances toughness and abrasion resistance, so the cutting edges keep their geometry longer under cyclic loading and abrasive wear. This results in fewer tool changes, steadier part tolerances and a better overall cost‑efficiency for medium‑to‑high volume turning tasks. The design reduces flank wear and helps preserve surface finish over longer runs. Reliable fit and process stability with standardised geometry Compliance with DIN 4976 (ISO 4) and the 12 x 12 mm cross‑section ensures full compatibility with ISO‑4 toolholders and tool posts commonly used in workshops and production lathes. The straight cutting orientation and the broad execution increase resistance to bending forces, offering a more rigid setup for facing and light roughing operations. An overall length of 100 mm keeps the tool manageable in confined toolposts while providing sufficient reach for typical external turning tasks. Practical handling, quick replacement and consistent results Equipped with a steel shank and diamond‑ground carbide cutting plates, the assembly supports accurate seating and repeatable positioning after index or replacement. Packaged in units of five, the set‑sized supply simplifies stock planning and reduces downtime caused by unexpected tool wear. The construction suits both small workshops and industrial settings seeking a durable, standardised insert tool that integrates easily into existing tooling systems. For robust turning operations choose the Wilke carbide turning tool for dependable wear resistance and DIN compatibility — contact Metav Werkzeuge for stock and application advice, either by email at info@metav-werkzeuge.com or by phone on +49 2822 7131930 Technical data Article number: 4118625102NW Item label: Drehmeißel DIN 4976ISO4 12x12mm HM P25/P30 ger. breit Wilke Material: Hartmetall P25/P30 Product type: Drehmeißel (turning tool) Overall length: 100 mm Cross‑section: 12 x 12 Cutting direction: gerade (straight) Standard: DIN 4976 (ISO 4) Packaging unit: 5 Manufacturer: Werner Wilke Zerspanungstechnik GmbH Facts Overall length: 100 mm Cross‑section: 12 x 12 mm Packaging unit: 5 Special features Carbide P25/P30 Broad profile DIN 4976 (ISO 4) compliant geometry Steel shank with diamond‑ground carbide cutting plates Straight cutting direction FAQ What does the DIN 4976 (ISO 4) designation mean for tool compatibility? DIN 4976 (ISO 4) defines a standardised shank and profile for square turning tools; the tool conforms to this standard so it fits ISO‑4 toolholders and posts without modification. Which carbide grade is used and what advantage does it offer? The tool is furnished with P25/P30 carbide, a balanced grade that provides improved wear resistance and edge stability for routine turning operations. What are the key dimensional specifications for setup planning? The tool features a 12 x 12 mm cross‑section and an overall length of 100 mm, suitable for standard ISO‑4 toolholders and common lathe toolposts. How is the product supplied and how does that affect workshop stock? Delivery is in units of five, enabling simple stock rotation and predictable replacement intervals to support continuous production. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
100mm Turning Tool Carbide P25/P30 Straight Left-Hand DIN 4971 (ISO 1) - Werner Wilke Zerspanungstechnik GmbH
Efficient machining with diamond-ground P25/P30 carbide and a standardised 12 x 12 mm DIN 4971 shank ensures consistent, accurate turning results; the straight, left-hand design reduces setup time and supports stable toolholding. Order directly via Metav Werkzeuge or contact our consultants for tailored advice. Turning tool DIN 4971 (ISO 1) 12 x 12 mm, carbide P25/P30 — Werner Wilke A Turning tool DIN 4971 (ISO 1) 12 x 12 mm for left-hand straight turning, fitted with diamond-ground P25/P30 carbide cutting inserts on a steel shank. Diamond-ground carbide inserts P25/P30 Straight DIN 4971 (ISO 1) 12 x 12 mm shank Left-hand cutting direction for specific operations Steel shank, robust mounting, precise seating Greater process reliability through carbide grade and ground geometry The tool combines a steel shank with diamond-ground carbide cutting inserts in P25/P30 grade, delivering a balance of wear resistance and toughness for general turning tasks. The diamond grinding of the insert faces refines the cutting edge and reduces micro-chipping, which in turn improves surface finish and extends the interval between tool changes. This results in a more consistent production output and lower rework rates for medium-duty turning operations. Standardised shank dimensions for quick integration Compliance with DIN 4971 (ISO 1) and a 12 x 12 mm cross-section allow straightforward mounting in standard toolholders and turret pockets. The 100 mm overall length provides sufficient overhang for typical setups while keeping rigidity high; this standardisation reduces setup time and minimises the need for custom adapters, supporting faster changeovers on the shop floor. Left-hand configuration to suit specific machining directions The left-hand cutting orientation is ideal for operations that demand material removal towards the machine tailstock or for adapting to existing fixture layouts. Using a dedicated left-hand tool avoids complex re-orientations of workpieces and helps maintain a stable cutting geometry, which contributes to predictable cycle times and a smoother workflow in mixed-production environments. Built for workshop resilience and straightforward use Constructed for routine use in industrial and trade workshops, the design emphasises robust seating and repeatable clamping. The combination of a solid steel shank and reliably mounted carbide inserts makes the tool a pragmatic choice where dependable performance and easy replacement are priorities. For users requiring guidance on toolholder compatibility or cutting data, Metav’s technical advisors can provide specific recommendations. Contact Metav Werkzeuge for application-specific advice and secure supply from our Emmerich facility; Metav Werkzeuge supports procurement and technical consultation for this Werner Wilke turning tool SKU 4118601552NW Technical data Article number: 4118601552NW Product type: Turning tool Manufacturer: Werner Wilke Zerspanungstechnik GmbH Compliance: DIN 4971 (ISO 1) Packaging unit: 5 Core dimensions Cross-section: 12 x 12 mm Overall length: 100 mm Materials & features Material: Carbide P25/P30 Form: Straight Cutting direction: Left-hand Shank: Steel shank fitted with diamond-ground carbide cutting inserts FAQ How is the tool mounted in a machine? The turning tool mounts to holders compatible with DIN 4971 (ISO 1); the 12 x 12 mm shank and 100 mm length match standard turret pockets and tool posts for quick installation. What does the P25/P30 carbide designation indicate? P25/P30 refers to carbide grades used for the inserts; these grades provide a general-purpose balance of hardness and toughness suitable for a wide range of turning tasks, with good wear resistance due to the diamond-ground finish. Is the cutting direction left-hand or right-hand? This model is a left-hand turning tool, designed for operations that require cutting towards the tailstock or for setups where a left-hand orientation improves accessibility. Are the cutting inserts supplied mounted on the shank? Yes, the tool is supplied as a steel shank fitted with diamond-ground carbide cutting inserts, ready for mounting and immediate use in compatible toolholders. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
10×10mm Turning Tool Carbide P25/P30 Right-Hand Straight, DIN 4971 (ISO 1) - Werner Wilke Zerspanungstechnik GmbH
Take advantage of the combination of carbide P25/P30 cutting tips, a DIN 4971 (ISO 1) straight form and a compact 10 x 10 mm shank for reliable, repeatable turning operations; order supply via Metav Werkzeuge or consult the technical team for application guidance. Turning tool DIN 4971 (ISO 1) 10 x 10 mm HM P25/P30 — straight, right-hand cutting by Werner Wilke Turning tool DIN 4971 (ISO 1) 10 x 10 mm HM P25/P30 is a straight, right-hand cutting tool designed for general turning tasks where consistent chip control and tool stability are required Carbide P25/P30 cutting tips for long life 10 x 10 mm square shank for secure clamping DIN 4971 (ISO 1) straight form for standard tool posts Right-hand cutting direction for conventional turning Precision and durability that support efficient production The straight shank design complies with DIN 4971 (ISO 1), which ensures compatibility with standard tool posts and quick integration into existing turning centres and lathes. Fitted with diamond-ground carbide plates in P25/P30 grades, the tool provides a balance between wear resistance and toughness; this combination reduces tool changes and maintains consistent component dimensions. The square 10 x 10 mm cross-section keeps the insert seat rigid under cutting loads, which improves surface finish and dimensional stability during interrupted cuts or heavy-facing operations. Clear performance benefits for workshop workflows Thanks to the carbide P25/P30 specification, the insert material is optimised for general-purpose steel machining, giving a durable cutting edge that withstands repeated use while preserving cutting geometry. The right-hand cutting orientation is suited to common turning setups, enabling predictable chip flow and easier set-up for operators. By standardising on a tool that follows ISO form and uses a compact shank, workshop throughput can be improved because toolholders and changeover procedures remain simple and repeatable. Practical explanation of technical terms and handling The designation P25/P30 refers to carbide grades with properties tuned to steel machining: P25 emphasises wear resistance for longer life, while P30 offers a compromise with slightly increased toughness. The term diamond-ground indicates a high-precision finish on the carbide plate, which helps reduce cutting forces and extend insert life. The straight configuration means the tool is not offset or angled, which is advantageous where a direct, rigid mounting is preferred. This turning tool is delivered pre-mounted on a steel shank with the carbide plate fixed, reducing set-up time and ensuring a consistent cutting geometry across multiple tools. Suitable applications and user advantages This tool is aimed at industrial machinists and service workshops that require a standard, reliable turning solution for steel components. Its 10 x 10 mm profile fits compact toolholders, making it particularly useful in multi-station setups and for small or medium-sized lathes. Because the tool is built to a widely recognised standard and fitted with robust carbide, maintenance intervals are extended and part tolerances are easier to achieve, which supports streamlined production and less rework. For precise turning operations or application-specific advice, contact Metav Werkzeuge for expert guidance and supply from Emmerich—technical consultants are available to discuss tool selection and compatibility with existing equipment Technical data Article number: 4118601052NW Label: Drehmeißel DIN 4971ISO1 10x10mm HM P25/P30 re. ger. Wilke Product type: Turning tool Material: Hartmetall P25/P30 Manufacturer: Werner Wilke Zerspanungstechnik GmbH Facts Total length: 90 mm Cross-section: 10 x 10 mm Form: straight Cutting direction: right-hand Packaging unit: 5 Special features Diamond-ground carbide cutting plates fitted on steel shank Conforms to DIN 4971 (ISO 1) standard Suitable for general steel turning tasks Straight execution for standard tool posts FAQ What materials is the turning tool suitable for? The turning tool is supplied with P25/P30 carbide, which is optimised for steel machining and general turning applications. Is the shank compatible with standard tool holders? Yes, the straight 10 x 10 mm shank and DIN 4971 (ISO 1) form ensure compatibility with common tool posts and holders. Does the tool cut left-hand or right-hand? This version is a right-hand cutting tool, intended for conventional turning directions. How does the diamond-ground plate benefit the process? The diamond-ground carbide plate offers a fine cutting edge finish that reduces cutting forces, improves surface quality and extends tool life. Can this tool be used for interrupted cuts or heavier facing operations? The robust square shank and carbide plates provide good stability for interrupted cuts and facing; however, machining parameters should be set according to material and machine capability. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
110mm 12 x 12 External Thread Turning Tool Carbide P25/P30 60° Right-Hand WN282 - Werner Wilke Zerspanungstechnik GmbH
Take advantage of the 60° thread profile, the carbide P25/P30 cutting tips and the stable 12 x 12 mm shank to achieve consistent external threads with minimal rework; order directly via Metav Werkzeuge or contact the sales team for precise compatibility advice. External thread turning tool 12 x 12 mm, carbide P25/P30, right-hand, 60° – Wilke The External thread turning tool 12 x 12 mm is designed for reliable external thread production in CNC and lathe operations, combining a rigid steel shank with diamond-ground carbide cutting plates for high repeatability. 12 x 12 mm square shank Carbide P25/P30 cutting tips 60° thread profile angle Right-hand cutting direction Consistent 60° thread form for less rework The 60° profile, executed by diamond-ground carbide tips, ensures a dependable thread geometry that reduces the need for subsequent corrections. The combination of carbide P25/P30 and precise tip finishing delivers repeatable flank accuracy and a uniform surface quality on each pass. This focused engineering reduces scrap rates and streamlines inspection routines, making the tool a practical choice where thread conformity matters for assembly or quality assurance. Rigid design that supports stable turning cycles A 12 x 12 mm cross-section and a total length of 110 mm provide a compact, stiff package that minimises chatter during threading operations. The tool is supplied as a steel shank fitted with mounted carbide cutting plates, which gives a stable interface between holder and cutting edge. The compact profile suits standard tool holders accepting a 12 x 12 mm square shank and supports steady cutting conditions that help maintain cycle times in production environments. Low-maintenance cutting tips and predictable service life Mounted carbide cutting plates, diamond-ground for accurate geometry, are selected for wear resistance and consistent cutting behaviour. The right-hand cutting direction matches conventional lathe threading cycles and supports straightforward setup. Regular inspection of the cutting plates and routine dressing where applicable extend productive life and reduce unplanned stoppages. The design emphasises uncomplicated handling and quick visual checks rather than complex maintenance procedures. Specification clarity and traceability for production planning Identified under norm WN282 and supplied in packaging units of 5, the tool is labelled and traceable for stock control and production planning. The compact specification and clear labelling facilitate procurement and ensure the tool integrates smoothly into existing tooling inventories. Purchasing via an established distributor offers the added benefit of consistent supply and documentation to support quality records and manufacturing audits. For procurement and technical enquiries regarding the Wilke WN282 external thread turning tool, contact Metav Werkzeuge for precise compatibility checks and ordering support Technical data Article number: 4118650252NW Type designation / norm: WN282 Product label: Außengewindedrehmeißel 12x12mm HM P25/P30 re. 60° Wilke Manufacturer: Werner Wilke Zerspanungstechnik GmbH Facts Overall length: 110 mm Cross-section: 12 x 12 mm Thread profile / tip angle: 60° Cutting direction: right-hand Packaging unit: 5 Special features Material: carbide P25/P30 Steel shank with mounted diamond-ground carbide cutting plates Execution: 60° thread profile FAQ Is this tool suitable for standard 12 x 12 mm tool holders? The tool’s 12 x 12 mm cross-section is intended for holders that accept a 12 x 12 mm square shank; the steel shank provides secure clamping for stable threading. What is the thread angle delivered by the cutting tips? The mounted carbide cutting plates are finished for a 60° thread profile in line with norm WN282. How is the cutting direction defined for this tool? This version is specified as right-hand cutting and is intended for conventional right-hand threading operations on lathes and CNC turning centres. Are the carbide plates replaceable or permanently mounted? The tool is supplied as a steel shank fitted with mounted carbide cutting plates; consult Metav Werkzeuge for details on spare parts and replacement options. How is the product delivered for inventory and planning? The article is supplied in a packaging unit of 5, facilitating stock management and orderly replenishment. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
110mm 16 x 10 Carbide Turning Tool, 80° Point, Straight Cut, DIN 4975 - Werner Wilke Zerspanungstechnik GmbH
Reliable workshop performance comes from combining a robust steel shank, cemented carbide P25/P30 cutting plates and a standardised interface for simple mounting; the 80° pointed geometry ensures repeatable, precise external turning. Order the turning tool directly via Metav Werkzeuge or ask the consultants for application advice. Wilke turning tool DIN 4975 — 16 x 10 mm, carbide P25/P30, pointed The Wilke turning tool DIN 4975 16 x 10 mm is a DIN‑standard lathe tool designed for precision external turning operations on conventional and CNC lathes. Cemented carbide P25/P30 tip for durability Conforms to DIN 4975 standard Steel shank fitted with diamond‑ground plates 80° pointed tip for accurate profiling Consistent cutting performance for everyday production The solid combination of a steel shank with diamond‑ground carbide cutting plates delivers stability in the toolholder and a consistently sharp cutting edge. The use of cemented carbide P25/P30 provides a balance between toughness and wear resistance, which supports predictable tool life in continuous turning tasks. This stability reduces downtime for re‑setting and contributes to a more efficient production flow without sacrificing surface quality. Standardised interface for fast set‑up and repeatability Designed to the DIN 4975 specification and produced in a 16 x 10 mm cross-section, the tool mates cleanly with compatible toolholders, simplifying changeovers and guaranteeing repeatable positioning. The 80° pointed tip creates an accurate contact geometry for external profiles and small radii, which aids process reliability and reduces the need for repeated checking. Clear, standard dimensions help planners and operators integrate the tool into existing tool sets without additional adapters. Practical design that suits workshop routines With a total length of 110 mm and a straight cutting direction, the unit is engineered for straightforward handling and mounting. The diamond‑ground inserts give a defined cutting edge geometry, improving the finish on turned components and allowing for predictable wear patterns. The construction supports routine maintenance procedures typical for metal‑cutting shops and keeps replacement and inspection tasks simple and quick. For tailored technical advice or to arrange a supply of these Wilke carbide turning tools, contact Metav Werkzeuge in Emmerich by email at info@metav-werkzeuge.com or by phone on +49 2822 7131930 — our specialists will assist with selection and compatibility details. Technical data Article number: 4118620052NW Label: Drehmeißel DIN 4975 16x10mm HM P25/30 ger. spitz Wilke Manufacturer: Werner Wilke Zerspanungstechnik GmbH Facts Overall length: 110 mm Cross-section: 16 x 10 mm Tip angle: 80° Packaging unit: 5 Special features Material: cemented carbide P25/P30 Design: pointed tip, straight cutting direction Standard: DIN 4975 Construction: steel shank with diamond‑ground carbide cutting plates FAQ What dimensions define the tool and its compatibility with toolholders? The turning tool is supplied in a 16 x 10 mm cross‑section with a total length of 110 mm and conforms to the DIN 4975 standard, so it fits compatible DIN‑4975 toolholders used in workshop and production environments. Which cutting geometry does the tool use for external turning? The unit features an 80° pointed geometry and a straight cutting direction; this configuration supports precise external profiling and repeatable contact geometry during turning operations. What is the cutting material and what benefits does it bring? The tool is equipped with cemented carbide P25/P30 plates; this grade offers a balance of wear resistance and toughness, promoting stable tool life and consistent surface finish. Can the carbide plates be reconditioned or replaced? The turning tool is built with diamond‑ground carbide plates mounted on a steel shank; replacement or reconditioning depends on the workshop’s maintenance practices and the spare parts availability for the Wilke system. Is this tool suitable for use on both manual lathes and CNC machines? The standardised DIN 4975 interface and robust construction make the tool suitable for mounting in both manual and CNC lathe toolholders where the 16 x 10 mm cross‑section and 80° tip meet the process requirements. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
110mm 16 x 10mm Grooving Tool Carbide P25/P30 4mm Cut Width, DIN 4981 (ISO 7) - Werner Wilke Zerspanungstechnik GmbH
Take advantage of the combination of industrial-grade Hartmetall P25/P30, standardised mounting and a compact 4 mm parting width for consistent, repeatable separations. Order the tool directly via Metav Werkzeuge or consult the team for application-specific guidance. Parting and Grooving Tool DIN 4981 (ISO 7) — 16 x 10 mm, Hartmetall P25/P30, right-hand (Wilke) A parting and grooving tool designed for precision turning and reliable chip control in standard ISO7 toolholders DIN 4981 (ISO 7) compatibility for standard mounting Carbide grade P25/P30 for general-purpose machining Steel shank with diamond-ground carbide inserts Compact 16 x 10 mm cross-section for stable clamping 4 mm cutting width for narrow parting operations Precise, repeatable parting with industrial carbide The tool delivers a reliable combination of die-hard carbide and standardised mounting, allowing stable, repeatable separations in turning processes. Built to DIN 4981 (ISO 7), the holder mates with commonly used toolposts and clamping systems; this reduces setup time and supports predictable tool height and alignment. The Hartmetall P25/P30 composition balances wear resistance with toughness, which is advantageous when working on a variety of ferrous components. The narrow cutting width results in reduced material removal per pass and improved surface finish at the cut face. Robust design for low-vibration performance and quick set-up A steel shank fitted with diamond-ground carbide cutting plates provides a rigid interface between the machine and the insert, minimising chatter and extending tool life. The 16 x 10 mm cross-section and 110 mm overall length offer a compact footprint that still provides necessary reach for many turning operations. The right-hand geometry suits conventional lathe set-ups and supports predictable chip flow away from the workpiece. This construction helps to keep cycle times steady and reduces rework, supporting efficient shop-floor throughput. Efficient use, predictable maintenance and application scope With an Einstechbreite (cutting width) of 4 mm, the tool is set up for narrow parting and grooving tasks where material waste must be controlled. The choice of P25/P30 carbide makes the tool a pragmatic option for general steel turning and typical workshop materials; its balanced wear resistance supports longer intervals between insert changes. Technical queries about compatibility or cutting data can be clarified quickly by the supplier; practical guidance helps to match cutting speeds and feeds to the carbide grade for best results. Contact Metav Werkzeuge today to discuss fitment, obtain cutting-data recommendations and secure reliable supplies of high-precision parting tools from stock in Emmerich Technical Data Article number: 4118645102NW Product type: Parting and grooving tool Norm: DIN 4981 (ISO 7) Label: Stechdrehmeißel DIN 4981ISO7 16x10mm HM P25/P30 re. Wilke Facts Overall length: 110 mm Cross-section: 16 x 10 mm Cutting width: 4 mm Packaging unit: 5 Special features Material: Hartmetall P25/P30 Right-hand cutting direction Steel shank with diamond-ground carbide inserts Compliant with DIN 4981 (ISO 7) FAQ Which machine types is this parting tool compatible with? The parting and grooving tool is compatible with lathes and turning centres that accept DIN 4981 (ISO 7) toolholders; compatibility is ensured by the standardised mounting system. What materials suit the Hartmetall P25/P30 grade best? The P25/P30 carbide grade is aimed at general-purpose turning of steels and similar ferrous materials where a balance of wear resistance and toughness is required. How wide is the cut this tool makes and what does that mean in practice? The tool offers a 4 mm cutting width, which is suitable for narrow parting and grooving tasks that demand minimal material removal and improved finish at the separated face. Is the tool supplied ready to fit or are inserts fitted on delivery? The item is supplied as a steel shank fitted with diamond-ground carbide cutting plates, ready for mounting in a compliant toolholder. Hersteller: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
110mm 16x16mm Offset Right-Hand Carbide Insert Side Turning Tool DIN 4980 (ISO 6) - Werner Wilke Zerspanungstechnik GmbH
Combine carbide P25/P30 cutting tips with the 16 x 16 mm cross-section and DIN 4980 compatibility for dependable, repeatable side turning in series production. Order the tool directly via Metav Werkzeuge or consult their specialists for application guidance. Side turning tool – 16 x 16 mm, Carbide P25/P30, DIN 4980 (ISO 6) by Werner Wilke The Side turning tool is designed for precision external turning on lathes, offering a DIN 4980 (ISO 6) interface and diamond-ground carbide tips for consistent surface quality. Carbide P25/P30 diamond-ground tips 16 x 16 mm rectangular cross-section Right-hand cutting direction DIN 4980 (ISO 6) toolholder interface Consistent cutting accuracy for repeatable parts The side turning tool delivers steady cutting performance thanks to its carbide cutting plates in grade P25/P30, which are diamond-ground for precise geometry and low runout. This construction reduces variation between parts and shortens inspection cycles, so machining processes become more predictable. The combination of a robust carbide grade with an engineered cutting geometry supports controlled chip formation and stable cutting forces, which is particularly important for medium-run production where repeatability and component tolerances are critical. Fast integration with standard toolholders Compatibility with DIN 4980 (ISO 6) ensures straightforward mounting in standard toolholders, simplifying set-up and changeover procedures. The offset shank design allows accurate positioning of the cutting edge relative to the workpiece datum, reducing the need for repeated adjustments. For workshops managing mixed fleets of lathes, the standard interface cuts complexity and speeds up tool replacement, helping to maintain spindle uptime and reduce cumulative set-up costs over multiple shifts. Durable construction that lowers maintenance needs A steel shank fitted with diamond-ground carbide cutting plates provides a balance between rigidity and wear resistance. The selected carbide grades offer good edge stability under interrupted cuts and maintain a sharp profile over extended use, which lowers the frequency of insert changes and reduces toolroom workload. The right-hand cutting orientation is optimised for standard turning directions on most engines, enabling predictable tool life and simplified inventory management. Practical supply and workshop logistics Measurements are precise and clear: 16 x 16 mm cross-section and an overall length of 110 mm, supplied in packs of 5 for efficient restocking. These dimensions make the tool suitable for typical holder geometries while the compact packing reduces storage footprint. For production planning, the consistent specification aids in SKU control and reorder cycles; technical enquiries about specific machining tasks can be directed to Metav Werkzeuge for tailored recommendations. Secure reliable turning performance by sourcing the Wilke side turning tool through Metav Werkzeuge for dependable supply from Emmerich; enquiries can be sent to info@metav-werkzeuge.com or by telephone on +49 2822 7131930 Technical data SKU: 4118640152NW Product type: Side turning tool Brand: Werner Wilke Zerspanungstechnik GmbH Cross-section: 16 x 16 mm Overall length: 110 mm Cutting direction: right-hand Packaging unit: 5 Interface standard: DIN 4980 (ISO 6) Form: offset Facts Cross-section: 16 x 16 mm Overall length: 110 mm Packaging unit: 5 SKU: 4118640152NW Special features Carbide P25/P30 Diamond-ground carbide cutting plates Offset shank Steel shank DIN 4980 (ISO 6) interface Right-hand cutting direction FAQ Which toolholder fits this turning tool? The side turning tool is compatible with toolholders conforming to DIN 4980 (ISO 6); the tool is supplied as Side turning tool (SKU 4118640152NW) by Werner Wilke. What is the cutting direction of the tool? The tool has a right-hand cutting direction, specified for the Side turning tool (SKU 4118640152NW) from Werner Wilke. What are the dimensions of the cutting shank? Cross-section is 16 x 16 mm and overall length is 110 mm for the Side turning tool (SKU 4118640152NW) supplied by Werner Wilke. What material are the cutting plates made from? The cutting plates are carbide P25/P30, diamond-ground for edge stability and precise geometry on the Side turning tool (SKU 4118640152NW). How is the tool packaged for supply? The Side turning tool (SKU 4118640152NW) by Werner Wilke is supplied in packs of 5 for convenient workshop replenishment. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
12 x 12mm Internal Radius Turning Tool Carbide P25/P30, Right-Hand, DIN 4974 (ISO 9) - Werner Wilke Zerspanungstechnik GmbH
Take advantage of the combination of carbide P25/P30 wear resistance, DIN 4974 (ISO 9) conformity and a compact 12 x 12 mm cross-section for reliable internal corner turning; order directly via Metav Werkzeuge or ask the technical consultants for tailored advice. Wilke internal corner turning tool DIN 4974 (ISO 9) — 12 x 12 mm, Carbide P25/P30, right-hand The Wilke internal corner turning tool DIN 4974 (ISO 9) is a right-hand internal corner tool designed for precision profiling in confined bores and fitted with diamond-ground carbide cutting plates on a steel shank Carbide P25/P30 tip for consistent wear resistance Conforms to DIN 4974 (ISO 9) standard 12 x 12 mm square shank for stable clamping Smallest bore Ø 21 mm for tight internal corners Consistent cutting quality for tight internal radii The tool delivers repeatable edge geometry through its diamond-ground carbide cutting plates, ensuring uniform chip formation and surface finish in internal profiles. Compliance with DIN 4974 (ISO 9) guarantees dimensional and manufacturing consistency, which reduces process variation on serial components. The carbide grade P25/P30 is selected for a balance of toughness and hardness, making the insert suitable for interrupted cuts and medium-duty internal turning tasks. This results in fewer tool changes and predictable tool life, supporting efficient machining cycles. Secure clamping and straightforward set-up A 12 x 12 mm square cross-section provides positive locating surfaces in standard tool holders, enabling rapid clamping and minimising deflection during turning operations. The steel shank, fitted with precision-mounted carbide plates, simplifies insert replacement and alignment on the holder. With a total length of 180 mm, the tool offers a practical reach for small-to-medium bores while keeping overhang low to reduce chatter. Mentioning the right-hand cutting direction clarifies orientation at set-up and avoids mounting errors. Practical benefits for workshop productivity Using a carbide-tipped internal corner tool reduces rework and sanding by producing a cleaner internal corner straight off the machine. The specified smallest bore Ø 21 mm makes this tool a solid choice for compact internal features where larger tools cannot access. Less manual finishing and fewer rejected parts translate into measurable time savings on the shop floor. For customers seeking reliable machining performance, the tool supports steady production rates and simplified inventory management thanks to its standardised geometry. For precision internal turning solutions from Wilke, contact Metav Werkzeuge for application advice and procurement assistance — Metav’s specialists are available to discuss requirements and recommend the optimal tooling setup Technical data Article number: 4118615152NW Product type: Internal corner turning tool Manufacturer: Werner Wilke Zerspanungstechnik GmbH Standard: DIN 4974 (ISO 9) Facts Total length: 180 mm Cross-section: 12 x 12 mm Smallest bore Ø: 21 mm Pack size: 5 pieces Special features Material: carbide P25/P30 Right-hand cutting direction Steel shank with diamond-ground carbide cutting plates Conforms to DIN 4974 (ISO 9) FAQ What is the minimum bore diameter suitable for this internal corner tool? The Wilke internal corner turning tool is suitable for bores down to 21 mm in diameter as specified for this SKU 4118615152NW. Which carbide grade is used for the cutting plates? Carbide P25/P30 is used for the cutting plates, offering a compromise between wear resistance and toughness for general internal turning. Is the tool intended for right-hand or left-hand cutting? This variant is a right-hand internal corner tool, designed for conventional turning directions in standard tool holders. How is the carbide supplied on the shank? The steel shank is fitted with diamond-ground carbide cutting plates, mounted to provide precise geometry and repeatable positioning. Can the tool be used for serial production runs? Yes, the standardised geometry and DIN 4974 (ISO 9) conformity make the tool suitable for repeated production with consistent results. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
12 x 12mm Turning Tool Carbide P25/P30 Straight Right-Hand DIN 4971 (ISO 1) - Werner Wilke Zerspanungstechnik GmbH
Take advantage of the combination of carbide P25/P30 durability, a standardised 12 x 12 mm square shank to DIN 4971 (ISO 1) and a compact 100 mm overall length for consistent, efficient lathe work. Order the turning tool directly via Metav Werkzeuge or ask our consultants if needed. Turning tool DIN 4971 (ISO 1) 12 x 12 mm, carbide P25/P30 (right-hand, straight) — Werner Wilke A turning tool DIN 4971 (ISO 1) 12 x 12 mm designed as a straight, right-hand lathe tool for precision external turning and general workshop turning applications Carbide P25/P30 grade for balanced wear resistance Square shank 12 x 12 mm to DIN 4971 Diamond-ground carbide tips for consistent sharpness Consistent cutting performance for general turning tasks Equipped with P25/P30 carbide, this lathe tool offers a reliable compromise between toughness and wear resistance, making it suitable for a wide range of turning operations. The diamond-ground carbide cutting tips maintain a sharp cutting edge, which reduces chatter and improves surface finish on turned components. Mounted on a straight steel shank to DIN 4971 (ISO 1), the tool provides repeatable seating and alignment in standard toolholders, supporting stable cuts and predictable tool life. Compact design that suits small setups and tight tool posts The compact 100 mm overall length combined with the 12 x 12 mm square cross-section allows the tool to fit into confined tool posts and multi-station turrets. Because the shank conforms to the DIN 4971 (ISO 1) specification, interchangeability between holders is simplified, reducing setup time and minimising the need for alternative adapters. The right-hand orientation is optimised for conventional turning directions, ensuring correct chip flow and cutting geometry without modification. Practical benefits for workshop productivity Using a standardised shank and robust carbide grade streamlines inventory management and reduces downtime from tool changes. The diamond-ground finish on the carbide tips improves initial cutting behaviour and extends effective tool life, which contributes to more consistent part tolerances and fewer reworks. For machine shops seeking straightforward, reliable tooling, this tool supports efficient production runs and predictable maintenance cycles. Handling and application guidance for best results The tool is supplied as a straight, right-hand turning tool with carbide tips mounted on a steel shank; correct clamping to the holder is essential for repeatable results. Ensure the insert and holder are aligned to the correct centre height and use appropriate feeds and speeds for the workpiece material to benefit from the P25/P30 combination. Regular inspection of the cutting edge for built-up edge or flank wear will preserve surface finish and dimensional accuracy over longer runs. Discuss application specifics and compatibility with Metav Werkzeuge to ensure the Wilke carbide turning tool matches the intended machining tasks Technical data Article number: 4118601102NW Product type: Turning tool Material: Carbide P25/P30 Cross-section: 12 x 12 mm Overall length: 100 mm Orientation: Right-hand Standard: DIN 4971 (ISO 1) Shank form: Straight Packaging unit: 5 Facts Cross-section: 12 x 12 mm Overall length: 100 mm Packaging unit: 5 SKU: 4118601102NW Special features Carbide P25/P30 Diamond-ground carbide cutting tips Straight execution Right-hand cutting direction Conforms to DIN 4971 (ISO 1) FAQ What material is used for the cutting tips? The Wilke turning tool is fitted with carbide P25/P30 cutting tips, chosen to balance toughness and wear resistance for general turning applications. Which shank standard and size does this tool use? The tool uses a 12 x 12 mm square shank in accordance with DIN 4971 (ISO 1) for standardised clamping and interchangeability. What is the overall length and packaging unit? Overall length is 100 mm and the tool is supplied in a packaging unit of 5 pieces. Is the tool suitable for left-hand turning? This variant is manufactured as a right-hand turning tool; left-hand operations require the corresponding left-hand version. How are the cutting tips finished? The carbide tips are diamond-ground, which enhances initial sharpness and contributes to a consistent surface finish. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
12 x 8mm Grooving Tool Solid Carbide P25/P30, 3mm Cut Width, DIN 4981 (ISO 7) - Werner Wilke Zerspanungstechnik GmbH
Precision parting and grooving is provided by a right-hand carbide cutting system in P25/P30, featuring a compact 12 x 8 mm cross-section and a 3 mm grooving width for repeatable, narrow cuts; order directly via Metav Werkzeuge or consult our specialists for application guidance. Wilke Parting Tool DIN 4981 (ISO 7) — Carbide P25/P30, 12 x 8 mm, right-hand A Wilke parting tool designed for precision grooving and cut-off operations on standard lathes, compliant with DIN 4981 (ISO 7) and fitted with diamond-ground carbide inserts. Carbide P25/P30 cutting insert Cross-section 12 x 8 mm 3 mm grooving width for precise parting Precise, repeatable parting for production stability The compact geometry of the tool, with a 12 x 8 mm cross-section and a narrow 3 mm grooving width, delivers consistently reproducible cuts and minimal material loss per operation. Compliance with DIN 4981 (ISO 7) ensures compatibility with standard tool holders and reliable clamping, which helps maintain process stability across batches. This configuration reduces setup variability and supports predictable cycle times for series production. Long service life through balanced carbide technology Equipped with P25/P30 carbide, the insert offers a balanced combination of hardness and toughness suitable for general turning and parting tasks. The grade provides resistance to abrasive wear while preserving edge stability during intermittent cuts, contributing to longer tool life and fewer indexings. For workshops seeking dependable performance, the carbide composition reduces unplanned downtime and supports consistent surface quality at the cut face. Straightforward mounting and rigid support reduces vibration A steel shank fitted with diamond-ground carbide inserts ensures accurate locating and secure clamping in standard parting tool holders. The modest 100 mm overall length is compatible with compact setups and provides sufficient overhang control to limit chatter. The robust mechanical connection simplifies tool changes and improves vibration damping, which benefits finish quality and dimensional accuracy in precision operations. Ready for conventional lathe applications and tight grooves With a right-hand cutting direction and a focused insert geometry, the tool is optimised for conventional parting and grooving where narrow kerfs are required. Delivered in a practical packaging unit, the set-up supports efficient stock management for workshops carrying out repetitive cut-off tasks. The configuration is particularly useful when space on the lathe carriage is limited and when clean separation of workpieces is essential. For tailored advice on integrating this Wilke parting tool into existing tool holders or production lines, contact Metav Werkzeuge for expert guidance and prompt delivery from Emmerich: +49 2822 7131930, info@metav-werkzeuge.com Technical data Article number: 4118645052NW Description: Parting tool DIN 4981 (ISO 7), 12 x 8 mm, HM P25/P30, right-hand Manufacturer: Werner Wilke Zerspanungstechnik GmbH Packaging unit: 5 pieces Facts Overall length: 100 mm Cross-section: 12 x 8 mm Grooving width: 3 mm Applicable standard: DIN 4981 (ISO 7) Special features Carbide: P25/P30 Steel shank with diamond-ground carbide inserts Right-hand cutting direction Suitable for precision parting and grooving operations FAQ What material is the insert made from? The insert is manufactured from P25/P30 carbide as specified for the Wilke parting tool (SKU 4118645052NW), offering a balance of wear resistance and edge stability. What grooving width does the tool provide? The tool provides a 3 mm grooving width, designed for narrow kerfs and precise parting operations in conventional lathe work. Which standard and holder compatibility apply? The tool conforms to DIN 4981 (ISO 7), ensuring compatibility with standard parting tool holders that accept this interface. How long is the tool and what is the cross-section? Overall length is 100 mm with a 12 x 8 mm cross-section, offering a compact profile for reduced overhang and improved rigidity. Is the cutting direction left- or right-hand? This version is right-hand cutting, optimised for conventional right-hand parting and grooving applications. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
12 x 8mm Parting Tool Solid Carbide P25/P30 3mm Cut Left DIN 4981 (ISO 7) - Werner Wilke Zerspanungstechnik GmbH
Benefit from a robust combination of carbide P25/P30 cutting edges, a standardised DIN 4981 (ISO 7) interface and a slim 3 mm parting width for reproducible, efficient separations in small-batch and series production. Order the parting tool directly via Metav Werkzeuge or consult the team for application advice. Parting tool DIN 4981 (ISO 7) — 12 x 8 mm, carbide P25/P30, left-hand (Wilke) A Wilke parting tool designed for precise cut-off operations in constrained setups, featuring a 12 x 8 mm shank and diamond-ground carbide inserts Solid carbide grade P25/P30 inserts DIN 4981 (ISO 7) interface standard 12 x 8 mm cross-section steel shank Left-hand cutting direction 3 mm parting width for narrow grooves Precision and wear resistance for repeatable cut-off operations This parting solution combines carbide P25/P30 cutting edges with diamond-ground seating to deliver consistent edge geometry and extended life. The hardened insert geometry reduces micro-chipping and maintains cutting geometry over multiple regrinds, which results in more predictable tool life and fewer machine stoppages. For production environments where reproducibility matters, the standardised DIN 4981 (ISO 7) interface ensures straightforward mounting and exchangeability in compatible toolholders, supporting steady cycle times and lower setup overhead. Narrow cutting width with controlled chip formation The 3 mm parting width offers narrow-groove capability while preserving stability thanks to the 12 x 8 mm shank profile and robust insert fixation. The diamond-ground seating improves thermal contact and reduces insert movement, which helps control chip evacuation and surface finish in the parted component. Such features make this design suitable for applications requiring compact separation cuts and a good balance between stiffness and accessibility in restricted tool pockets. Compatibility and functional design for workshop workflows With a 12 x 8 mm cross-section and a left-hand cutting configuration, the tool is compatible with holders that accept DIN 4981 (ISO 7)-mounted inserts and simplifies tool change routines on conventional lathes and automated turning centres. The steel shank fitted with diamond-ground carbide inserts provides mechanical stability and repeatable positioning, which shortens calibration cycles and supports inline quality control. Left-hand orientation is pre‑set for operations that demand cut direction consistency without additional fixturing. Reliable supply and practical handling for production use Delivered in a practical packaging unit, the tool set supports efficient stock rotation and predictable replenishment for production shops. The combination of a standardised interface, clearly specified shank dimensions and a defined parting width reduces procurement complexity and supports centralised tool management. As a result, maintenance intervals can be planned more reliably and tool inventories kept leaner without compromising availability. For tailored specification advice or to secure a reliable supply of this Wilke parting tool, contact Metav Werkzeuge GmbH at info@metav-werkzeuge.com or call +49 2822 7131930 for fast, localised service from Emmerich. Technical data Article number: 4118645502NW Designation: Parting tool (Stechdrehmeißel) Material: Carbide P25/P30 Standard: DIN 4981 (ISO 7) Facts Overall length: 100 mm Cross-section: 12 x 8 mm Parting width: 3 mm Packaging unit: 5 pieces Special features Steel shank fitted with diamond-ground carbide inserts Left-hand cutting direction Interface: DIN 4981 (ISO 7) FAQ What interface does this parting tool use? The tool uses the DIN 4981 (ISO 7) interface, allowing mounting in standard holders that accept ISO 7-mounted parting inserts. What is the specified parting width and how narrow are the cuts? The cutting width is 3 mm, designed for narrow-groove separations where a slim kerf is required. Which carbide grade is fitted and what does that mean? Fitted with carbide P25/P30 inserts, the tool combines wear resistance and edge stability suited to general turning and parting tasks that require predictable tool life. Is the tool supplied as a single item or in multipacks? The product is supplied in a packaging unit of 5 pieces, enabling simple stock replenishment for small workshops and production lines. What is the SKU for ordering or stock identification? The SKU for this item is 4118645502NW, which should be used for enquiries and reorders. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
125mm 20 x 12mm Carbide Turning Tool 80° Point Straight Cut DIN 4975 - Werner Wilke Zerspanungstechnik GmbH
Combine robust carbide P25/P30 tips with a standardised DIN 4975 shank and an 80° pointed geometry to ensure consistent finishing and long tool life in routine turning operations. Order the turning tool directly via Metav Werkzeuge or consult our specialists for holder compatibility and workshop optimisation. Turning tool DIN 4975, 20 x 12 mm — pointed carbide P25/P30, Werner Wilke The turning tool DIN 4975 20 x 12 mm is a pointed-profile lathe tool mounted on a steel shank, designed for precise external turning and finishing tasks in standard tool holders. Carbide P25/P30 tips for durable cutting DIN 4975 shank, 20 x 12 mm cross section 80° pointed geometry for precise turning Precision and durability for consistent turning results The tool combines carbide P25/P30 cutting plates with a diamond-ground finish to deliver a reliable edge that sustains dimensional accuracy and surface quality over extended runs. The pointed geometry minimises vibration during fine cuts, improving repeatability in finishing passes and reducing the need for rework. With the cutting plates mounted on a rigid steel shank, the assembly is optimised to transfer cutting forces cleanly, which contributes to stable machining and predictable tool life. Fast integration with standard tool systems and reduced setup time Designed to the DIN 4975 profile, the shank with a 20 x 12 mm cross section fits common tool holders without additional adaptation, lowering setup complexity and downtime. The 125 mm overall length provides sufficient projection for a variety of external turning applications while keeping rigidity high. Standardised dimensions enable quicker changeovers and simpler inventory management for workshops that rely on consistent tooling geometry across machines. Practical cutting geometry for dependable workshop performance An 80° tip angle with a pointed configuration supports accurate profiling and fine finishing, while the straight cutting direction suits conventional turning cycles. The assembly’s construction—steel shank equipped with diamond-ground carbide plates—favourably balances toughness and edge retention for routine production work. For purchasers seeking guidance on holder selection or specific machining tasks, technical advice is available to align tool choice with production goals and processing parameters. Contact Metav Werkzeuge for personalised advice on holder compatibility and workshop supply from our Emmerich location; call +49 2822 7131930 or e‑mail info@metav-werkzeuge.com to discuss application suitability and delivery options Technical data Article number: 4118620102NW Product type: Turning tool Material: Carbide P25/P30 Standard: DIN 4975 Cross section: 20 x 12 mm Overall length: 125 mm Tip angle: 80° Cutting direction: straight Form: pointed Packaging unit: 5 Facts Cross section: 20 x 12 mm Overall length: 125 mm Tip angle: 80° Packaging unit: 5 Special features Steel shank with diamond-ground carbide cutting plates Carbide grade P25/P30 Pointed geometry (spitz) DIN 4975 compatibility Designed for external turning and finishing operations FAQ What holder standard does this turning tool require? The tool is manufactured to the DIN 4975 standard and therefore fits tool holders designed for a 20 x 12 mm shank profile. Is the cutting edge pre-ground or coated? The turning tool is supplied with diamond-ground carbide cutting plates in grade P25/P30; no additional coating is specified. How long is the tool and how does that affect rigidity? The overall length is 125 mm; this length offers a compromise between reach and rigidity suitable for typical external turning tasks. Can this tool be used for finishing and profiling? Yes, the 80° pointed geometry is intended to support precise profiling and finishing operations while maintaining surface quality. What is the packaging unit and how is it supplied? The item is supplied in a packaging unit of 5, facilitating routine replacement and small-batch stocking. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
125mm 20 x 12mm Grooving Turning Tool Carbide P25/P30 5mm Cut Right-Hand, DIN 4981 (ISO 7) - Werner Wilke Zerspanungstechnik GmbH
Take advantage of a compact, right-handed parting tool solution with diamond‑ground carbide cutting plates and a precise 5 mm cut‑off width to maintain reproducible separations — available through Metav Werkzeuge with expert advice for fast workshop supply. Parting tool DIN 4981 (ISO 7) 20 x 12 mm, Carbide P25/P30 — right‑handed, Werner Wilke Parting tool DIN 4981 (ISO 7) 20 x 12 mm, Carbide P25/P30 — right‑handed, Werner Wilke is a right‑handed cut‑off and grooving tool intended for lathe use, featuring diamond‑ground carbide plates mounted on a steel shank for consistent edge quality and reliable separation. Carbide P25/P30 cutting plates Precise 5 mm cut‑off width Cross‑section 20 x 12 mm for standard holders Diamond‑ground plates on steel shank Precision and stability for reproducible separations The right‑handed parting tool is engineered to give consistent separation performance in routine turning operations. The carbide P25/P30 plates deliver a stable cutting edge that resists premature wear, while the diamond‑ground finish on the plates improves seating accuracy and reduces micro‑vibrations during cutting. With a 5 mm cut‑off width, the tool provides controlled material removal for clean parting without unnecessary material loss, helping to reduce scrap and rework in repetitive production. Productivity benefits and predictable tool behaviour A combination of a robust steel shank and precision‑finished cutting plates supports steady machining conditions and simpler tool life planning. The standard DIN 4981 (ISO 7) interface and the 20 x 12 mm cross‑section make the tool readily compatible with common toolholders, which reduces set‑up time and minimises downtime between operations. The straightforward geometry promotes reliable chip control during short, decisive cut‑off passes, enabling smoother cycle times and a more economical workflow. Workshop compatibility and handling advantages The tool’s overall length of 125 mm and compact cross‑section simplify installation in constrained tool posts and allow close control of overhang. Supplied in a packaging unit of 5, the tool is suited to small batch replenishment or stocking for routine maintenance. Right‑handed cutting direction and clear specification of the 5 mm cut‑off width make process planning straightforward for operators and ensures compatibility with existing turning setups adhering to DIN 4981 (ISO 7). Delivered as a ready‑to‑fit unit, the tool streamlines tool change procedures and supports steady production flow. Contact Metav Werkzeuge for tailored advice and fast supply from Emmerich — specialists can confirm holder compatibility and delivery times to suit the workshop's needs. Technical data Article number: 4118645152NW Product type: Stechdrehmeißel Manufacturer: Werner Wilke Zerspanungstechnik GmbH Standard: DIN 4981 (ISO 7) Dimensions / Core data Cross‑section: 20 x 12 mm Overall length: 125 mm Cut‑off width: 5 mm Cutting direction: right‑handed Packaging unit: 5 Materials / Special features Material: Hard metal (carbide) P25/P30 Steel shank with diamond‑ground carbide cutting plates Right‑handed configuration Designed for DIN 4981 (ISO 7) toolholders FAQ What is the cut‑off width of this tool? The cut‑off width is 5 mm, as specified for the parting tool (Stechdrehmeißel). Which carbide grade is fitted to the cutting plates? The cutting plates are carbide P25/P30, providing a balance of toughness and wear resistance for general turning tasks. Is the tool right‑ or left‑handed? This item is right‑handed, suitable for operations that require a right‑hand cutting direction. What are the key dimensions to check for holder compatibility? Check the 20 x 12 mm cross‑section and the DIN 4981 (ISO 7) interface; the overall length is 125 mm for fitting considerations. How many pieces are supplied per unit? The packaging unit contains 5 tools. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
125mm 20 x 20 Bent Turning Tool Solid Carbide P25/P30 Right-Handed, DIN 4972 (ISO 2) - Werner Wilke Zerspanungstechnik GmbH
Take advantage of a carbide P25/P30 cutting edge combined with a bent profile and DIN conformity for stable, repeatable turning results; order directly via Metav Werkzeuge or consult the advisors for application guidance. Turning tool DIN 4972 (ISO 2) 20 x 20 mm, carbide P25/P30 — bent, right-hand turning tool (Werner Wilke) Turning tool DIN 4972 (ISO 2) 20 x 20 mm, carbide P25/P30 is a bent, right-hand lathe tool equipped with diamond-ground carbide inserts on a steel shank, designed for precision external turning in production and workshop environments Carbide grade P25/P30 for long life Bent profile for improved access DIN 4972 (ISO 2) compatibility Right-hand cutting direction Consistent cutting performance from a precision carbide grade The tool's carbide composition, specified as P25/P30, provides a balanced combination of hardness and toughness suitable for a broad range of turning tasks. This grade is selected to deliver wear resistance and consistent edge retention, which reduces the frequency of regrinding and tool changes in batch production. The use of a diamond-ground cutting face on the insert enhances the initial sharpness and reduces vibration at cut start, contributing to a stable surface finish and predictable tool life in continuous operations. Bent profile for access in confined setups and controlled chip evacuation A bent tool body improves approach angles in applications where straight holders are obstructed or where the geometry of the workpiece demands an offset cutting position. The tool's construction — a steel shank fitted with diamond-ground carbide inserts — stabilises the cutting edge and directs chips away from the work area, lowering the risk of recutting and improving process reliability. The bent shape also facilitates setup in multi-station lathes and reduces the need for additional fixturing in awkward tool positions. Standardised dimensions for secure clamping and repeatable results Manufactured to DIN 4972 (ISO 2), the tool uses a 20 x 20 mm cross-section that matches common toolholder slots, enabling a secure fitting that minimises play under load. With an overall length of 125 mm, the geometry is compact enough for close-quarter turning yet long enough to provide appropriate leverage and clearance on conventional toolposts. Standard conformity means compatibility across equipment ranges and simplifies stocking and reordering strategies for maintenance teams. Production-oriented design for reliable right-hand external turning Configured for right-hand cutting, this turned tool delivers repeatable performance for external facing and profiling tasks where direction-specific geometry is required. The combination of a prepared carbide cutting face and a robust shank supports stable cuts at moderate to higher feed rates when paired with suitable insert grades and machine settings. The design is aimed at workshops and industrial users seeking a dependable, ready-to-fit solution for everyday turning operations. Contact Metav Werkzeuge today for precise application advice and secure supply of turning tools tailored to production needs; Metav Werkzeuge’s consultants can advise on compatibility and batch requirements Technical data Article number: 4118605202NW Label: Turning tool DIN 4972 (ISO 2) 20 x 20 mm, carbide P25/P30, bent, right-hand Manufacturer: Werner Wilke Zerspanungstechnik GmbH Facts Cross section: 20 x 20 mm Overall length: 125 mm Packaging unit: 5 UID: 4118605202NW Special features Material: Hartmetall P25/P30 (carbide) Form: bent Standard: DIN 4972 (ISO 2) Cutting direction: right-hand Steel shank with diamond-ground carbide inserts FAQ What materials is this turning tool intended for? The turning tool from Werner Wilke, specified as a carbide tool with P25/P30 grade, is designed primarily for standard turning applications where carbide inserts are appropriate; matching insert grades should be selected to suit specific workpiece materials. Is the tool compatible with standard toolholders? Yes — compliance with DIN 4972 (ISO 2) and the 20 x 20 mm cross-section ensure compatibility with common toolholders that accept this standard size. Can the carbide inserts be resharpened or replaced? The diamond-ground carbide cutting plates are intended for replacement or reconditioning according to workshop practice; replacement inserts that match the original geometry will restore cutting performance. Does the bent design affect cycle times or finish quality? The bent profile improves access and chip direction; when combined with the P25/P30 carbide grade and correct machining parameters, it supports consistent surface finish and reliable cycle performance. What is the packaging unit and how is the product supplied? The product is supplied in packaging units of 5, allowing for small-batch replenishment and straightforward workshop stocking. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
125mm 20 x 20 Indexable Face Turning Tool Carbide P25/P30, Offset, DIN 4977 (ISO 5) - Werner Wilke Zerspanungstechnik GmbH
Achieve repeatable turning with carbide P25/P30 cutting edges, a compact 20 x 20 mm cross-section and an offset shank that improves clearance in tight set-ups. Order the face-turning tool directly via Metav Werkzeuge or ask our consultants if needed. Face-turning tool DIN 4977 (ISO 5) 20 x 20 mm – Carbide P25/P30 (Werner Wilke) The Face-turning tool DIN 4977 (ISO 5) 20 x 20 mm delivers precise right-hand face turning for industrial steel applications with a steel shank fitted with diamond-ground carbide cutting plates Carbide P25/P30 grade for steel turning Offset shank for improved clearance Complies with DIN 4977 (ISO 5) Right-hand cutting, 20 x 20 mm cross-section Consistent metal removal with proven carbide grades The tool is built around carbide P25/P30, a grade selected for stable performance in general steel machining. The combination of diamond-ground carbide cutting plates and a robust steel shank yields a reliable cutting edge that holds form under repeated passes. This construction reduces the frequency of regrinding and tool changes, improving uptime on production lathes. The result is a predictable machining process with consistent surface quality and dimensional control Geometry and handling designed for confined operations The offset shank and compact 20 x 20 mm cross-section permit access to faces and shoulders where larger tooling would collide with fixtures. The design minimises interference while maintaining the rigidity required for face operations. Right-hand cutting geometry ensures correct chip flow and stable contact during standard clockwise spindle rotation, supporting efficient cycle times and fewer clearance adjustments for operators working with turned parts Standards, compatibility and practical benefits Compliance with DIN 4977 (ISO 5) simplifies specification and replacement across tool-holding systems. The overall length of 125 mm provides a balance between reach and stiffness for common workshop set-ups. Fitted inserts deliver fast indexable replacement in case of wear, keeping maintenance straightforward. The face-turning tool by Werner Wilke is suitable where robust, repeatable finishing and roughing on steel components are required, combining standardised dimensions with industry-grade P25/P30 performance For secure procurement and application guidance on this Wilke face-turning tool, contact Metav Werkzeuge for a tailored recommendation or technical clarification via info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: 4118630102NW Label: Stirndrehmeißel DIN 4977ISO5 20x20mm HM P25/P30 re. Wilke Product type: Face-turning tool Manufacturer: Werner Wilke Zerspanungstechnik GmbH UID: 4118630102NW Facts Overall length: 125 mm Cross-section: 20 x 20 mm Standard: DIN 4977 (ISO 5) Packaging unit: 5 Special features Material: Carbide P25/P30 Form: Offset (abgesetzt) Cutting direction: Right-hand Steel shank with diamond-ground carbide cutting plates Designed for industrial face turning applications FAQ What materials is this tool intended to machine? The face-turning tool with carbide P25/P30 is designed primarily for steel machining; its carbide grade delivers a balance of toughness and wear resistance suited to typical steel turning tasks. Is the tool compatible with standard DIN 4977 tool holders? Yes, the tool is specified to DIN 4977 (ISO 5), ensuring compatibility with holders and fixtures that accept this standard form and dimensions. How is wear managed on the cutting edges? Wear is managed by indexed carbide cutting plates; when one edge is worn the insert can be rotated or replaced, maintaining cutting performance without full-tool replacement. What does the offset (abgesetzt) form provide in practice? The offset form increases clearance between the shank and the workpiece or fixture, enabling operations in confined spaces while retaining rigidity for face turning. Which SKU identifies this specific variant? This variant is identified as SKU 4118630102NW, the Wilke right-hand face-turning tool with a 20 x 20 mm cross-section. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
125mm 20 x 20 Side Turning Tool Carbide P25/P30 Offset DIN 4980 (ISO 6), Left-Hand - Werner Wilke Zerspanungstechnik GmbH
Take advantage of the combination of diamond-ground carbide cutting plates and a DIN-compliant 20 x 20 shank for consistent, repeatable side turning. The offset design provides access in confined set-ups while the P25/P30 grades deliver a balanced wear resistance and toughness for general turning tasks. Order the tool directly via Metav Werkzeuge or ask the consultants for tailored advice. Wilke side-turning tool DIN 4980 (ISO 6) — 20 x 20 mm, carbide P25/P30, left-hand The Wilke side-turning tool is an offset lathe tool, fitted with diamond-ground carbide plates for precise side-facing and profiling operations where a DIN 4980 (ISO 6) shank is required Carbide P25/P30 cutting plates Offset shank for tight access DIN 4980 (ISO 6) standard shank 125 mm overall length, 20 x 20 shank Consistent edge quality for predictable cuts The steel shank is fitted with diamond-ground carbide plates in P25/P30, which means the cutting edges are shaped and finished to a high degree of precision. This results in a consistent cutting geometry and reduced runout at the tip, translating into stable chip formation and predictable surface finish. For workshops that depend on repeatability, the combination of a solid shank and precisely finished carbide inserts reduces variation between workpieces and limits the need for frequent re-adjustment. The emphasis here is on measurable process stability rather than marketing claims. Standardised shank for straightforward toolholding Compliance with DIN 4980 (ISO 6) provides clarity when selecting toolholders and fixtures: the shank dimensions follow an established standard for lathe tooling, making it simpler to verify clamp fit and set-up height. The 20 x 20 cross-section and the overall 125 mm length support common toolpost and turret systems used in general workshop and light industrial turning. Using a standard shank reduces setup time and the risk of incorrect mounting, which contributes directly to throughput and machining safety. Offset geometry and left-hand orientation for specific tasks The offset (abgesetzt) form allows the cutting tip to reach shoulders, grooves and other side-facing features that would be difficult with a straight profile. The tool’s left-hand cutting direction means it is intended for operations where the tool cuts when fed from right to left; this is important when planning tool layout for multi-station or multi-tool turning operations. Selecting left- or right-hand orientation according to the machining sequence prevents clashes and ensures that feeds and clearances work as intended. Robust construction aimed at workshop productivity The use of carbide plates on a rigid steel shank offers durability and reduced maintenance intervals compared with regrindable high-speed steel solutions. Diamond-ground plates maintain a consistent edge profile for longer, which reduces dressing frequency and supports uninterrupted production runs. The design prioritises functional resilience: fewer tool changes, reduced setup interventions and stable part quality all contribute to improved machine utilisation in everyday workshop practice. For advice on integrating Wilke carbide tooling into a current turning line or to place an order, contact Metav Werkzeuge in Emmerich for straightforward, expert guidance at info@metav-werkzeuge.com or call +49 2822 7131930 — Metav can assess compatibility and delivery options quickly Technical data Article number: 4118640652NW Product type: Side-turning tool Brand: Werner Wilke Zerspanungstechnik GmbH Facts Overall length: 125 mm Cross-section: 20 x 20 mm Packaging unit: 5 Special features Material: Carbide P25/P30 Form: Offset Standard: DIN 4980 (ISO 6) Steel shank with diamond-ground carbide cutting plates Left-hand cutting direction FAQ What materials are best machined with this side-turning tool? The Wilke side-turning tool is fitted with P25/P30 carbide plates; these grades offer a balanced combination of wear resistance and toughness suited to general turning tasks common in workshop environments. How does the DIN 4980 (ISO 6) shank help with set-up? DIN 4980 (ISO 6) standardisation ensures the 20 x 20 shank dimensions match common toolholders, simplifying clamping, height setting and toolholder selection for reliable mounting. What does left-hand orientation mean in practice? Left-hand orientation indicates the tool is intended to cut when fed from right to left; this affects tool placement and the sequence of operations to avoid collisions and ensure correct chip flow. Can the carbide plates be replaced or reconditioned? The design uses fitted diamond-ground carbide plates; replacement procedures depend on the holder design and workshop practices — spare plates and instructions are typically sourced via the supplier. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
125mm 20 x 20 Straight Turning Tool Wide Carbide P25/P30, DIN 4976 (ISO 4) - Werner Wilke Zerspanungstechnik GmbH
Take advantage of a broad 20 x 20 mm profile and diamond-ground carbide cutting plates for steady, repeatable turning operations; order directly via Metav Werkzeuge or request technical advice from our consultants. Turning tool DIN 4976 (ISO 4) 20 x 20 mm – broad carbide-equipped turning tool by Werner Wilke The Turning tool DIN 4976 (ISO 4) 20 x 20 mm is a broad, straight-cutting lathe tool fitted with diamond-ground carbide plates, designed for reliable external turning and easy integration into standard holders Broad 20 x 20 profile for stable clamping Carbide grade P25/P30 for wear resistance Conforms to DIN 4976 (ISO 4) standard Steel shank with diamond-ground cutting plates Long-term stability and consistent cutting results This turning tool delivers stable cutting performance thanks to its broad 20 x 20 cross-section and solid construction. The steel shank combined with diamond-ground carbide plates provides a rigid connection between toolholder and insert, reducing vibration and improving surface finish. For production environments where repeatability is critical, the robust geometry helps maintain tolerances over prolonged runs and supports predictable tool life. The compliance with DIN 4976 (ISO 4) ensures compatibility with standard tool clamping systems, simplifying setup and changeover. Precision-ground carbide for extended service life Equipped with carbide P25/P30, the tool offers a balanced combination of toughness and hardness suitable for general turning tasks. Diamond grinding of the cutting plates refines edge geometry and reduces microchipping, which translates into longer intervals between regrinds and fewer interruptions. The result is reduced downtime and improved process economy without complex handling procedures. The carbide designation indicates a commercially established grade used where dependable wear resistance is required. Designed for simple integration and secure fastening The broad form and standardised shank dimensions allow direct mounting in common toolholders that accept the DIN 4976 (ISO 4) profile. The 20 x 20 section gives even contact in clamping devices, lowering the risk of tool movement under load and ensuring consistent cut depth. Where machines and fixtures follow international norms, installation is straightforward: set the tool to centre height, secure the clamping, and verify alignment. This practical design reduces setup time and supports faster machine cycles. Practical workshop benefits and handling Packaged in a small multiple unit, the item supports stock control for small and medium-sized workshops that require quick replacements. The construction with carbide tips on a steel shank provides a balance between replaceable cutting performance and low-cost carrier durability. Operators will notice improved surface quality and fewer edge failures, while maintenance routines remain uncomplicated. Documentation and labelling follow industry conventions so that identification and replenishment are quick and traceable. For robust, precision turning with Werner Wilke tooling, contact Metav Werkzeuge for ordering and tailored technical consultation — info@metav-werkzeuge.com • +49 2822 7131930 Technical data SKU: 4118625202NW UID: 4118625202NW Product type: Turning tool Manufacturer: Werner Wilke Zerspanungstechnik GmbH Label: Drehmeißel DIN 4976ISO4 20x20mm HM P25/P30 ger. breit Wilke Core data Overall length: 125 mm Cross section: 20 x 20 mm Packaging unit: 5 Standard: DIN 4976 (ISO 4) Special features Material: Carbide P25/P30 Form: broad Cutting direction: straight Shank: steel shank with diamond-ground carbide cutting plates FAQ What does DIN 4976 (ISO 4) indicate for this tool? DIN 4976 (ISO 4) denotes the standardised shank and profile for turning tools, ensuring the Turning tool DIN 4976 (ISO 4) 20 x 20 mm from Werner Wilke fits common holders that accept this specification. Which carbide grades are fitted and what are their benefits? The tool is fitted with carbide P25/P30 plates; these grades provide a compromise of toughness and wear resistance that supports longer tool life and reliable performance in general turning tasks. Is this tool suitable for automated turret change systems? The 20 x 20 broad profile and conformity to DIN 4976 (ISO 4) make the tool compatible with many automated turret and holder systems designed for standardised shank dimensions. How is the cutting edge prepared on the tool? Cutting plates are diamond-ground, which refines the cutting geometry, reduces microchipping and contributes to improved surface finish and extended intervals between regrinds. How many tools are supplied per packaging unit? The item is supplied in packaging units of five, allowing straightforward stock replenishment for workshop needs. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
125mm 20 x 20mm Side Turning Tool Carbide P25/P30 Offset DIN 4980 (ISO 6) - Werner Wilke Zerspanungstechnik GmbH
A robust choice for precise side turning: carbide P25/P30 inserts, a 20 x 20 mm cross-section and a stepped shank to DIN standard ensure consistent cutting performance and straightforward integration into existing toolholders — order directly via Metav Werkzeuge or consult the team for compatibility advice. Side turning tool DIN 4980 (ISO 6) 20 x 20 mm, carbide P25/P30, right-hand – Werner Wilke The side turning tool is a stepped-shank lathe tool designed for accurate external side cuts and finishing operations in general turning applications Carbide P25/P30 inserts for consistent performance Cross-section 20 x 20 mm for rigid mounting Right-hand cutting for standard turning operations Stepped shank to DIN 4980 (ISO 6) for compatibility Greater cutting consistency for reliable production The tool combines carbide P25/P30 cutting material with diamond-ground inserts, delivering stable edge geometry and predictable wear behaviour. This consistency reduces the need for rework and shortens cycle variability, which supports higher throughput in batch production. The right-hand cutting orientation is suited to the majority of conventional lathe setups, while the insert-grade maintains a balance between toughness and hardness for longer life in interrupted cuts. Fast integration and predictable setup times Compliance with DIN 4980 (ISO 6) and the 20 x 20 mm cross-section simplifies tooling logistics: the stepped shank fits standard toolholders without custom modification, reducing setup time and supporting repeatable clamping. The stepped (abgesetzt) design positions the cutting head reliably, so machine offsets remain consistent from one changeover to the next. For operations that demand steady process windows, this leads to fewer adjustments and quicker ramp-up to full production speed. Durability that keeps workshops running A steel shank fitted with diamond-ground carbide inserts provides a robust connection between the holder and the cutting edge, while the overall length of 125 mm gives sufficient reach for many external turning tasks without sacrificing rigidity. The construction is aimed at routine workshop use: reduced vibration through the rigid cross-section translates into improved surface finish and prolonged insert life. For procurement teams seeking predictable maintenance intervals, the component supports straightforward inventory and replacement strategies. Select the Werner Wilke side turning solution with its certified DIN 4980 (ISO 6) interface and carbide P25/P30 inserts — contact Metav Werkzeuge for expert advice and rapid supply from Emmerich. Technical data Article number: 4118640202NW Product type: Side turning tool Manufacturer: Werner Wilke Zerspanungstechnik GmbH Material: Carbide P25/P30 Cross-section: 20 x 20 mm Overall length: 125 mm Cutting direction: Right-hand Standard: DIN 4980 (ISO 6) Form: Stepped Packaging unit: 5 Facts Cross-section: 20 x 20 mm Overall length: 125 mm Packaging unit: 5 Special features Carbide P25/P30 cutting material Stepped shank for standard toolholders Diamond-ground carbide inserts mounted on steel shank Right-hand cutting orientation FAQ What materials is this tool suitable for? The side turning tool with carbide P25/P30 inserts is suitable for general turning tasks on common workshop steels and similar materials; tool life will vary with material hardness and cutting parameters. Is the stepped shank compatible with standard holders? Yes — the DIN 4980 (ISO 6) stepped shank ensures compatibility with holders designed for a 20 x 20 mm cross-section, enabling straightforward integration into existing setups. How long is the tool and what reach does it provide? The tool has an overall length of 125 mm, providing sufficient reach for most external side turning operations while maintaining rigidity. Are replacement inserts available for the tool? Replacement inserts in carbide P25/P30 grade are used on the tool; matching inserts should be specified to maintain the intended cutting performance. What is the SKU for ordering or reference? Reference SKU: 4118640202NW for the Werner Wilke side turning tool Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
140mm 10x10mm Internal Thread Turning Tool Carbide P25/P30 60° Right-Hand WN283 - Werner Wilke Zerspanungstechnik GmbH
Benefit from durable carbide P25/P30 grades, a precise 60° thread profile and a robust 10 x 10 mm shank for dependable internal threading in series production. Order the internal thread turning tool directly via Metav Werkzeuge or consult the Metav advisors for application-specific recommendations. Internal thread turning tool 10 x 10 mm, carbide P25/P30, right-hand 60° — Wilke The Internal thread turning tool 10 x 10 mm (carbide P25/P30) is a right-hand, 60° profile tool intended for secure internal threading operations; it is mounted on a steel shank fitted with diamond-ground carbide cutting inserts for repeatable performance Carbide P25/P30 for consistent wear resistance 60° profile for standard metric threads 10 x 10 mm square shank, 140 mm overall length Steel shank with diamond-ground carbide inserts Consistent material selection for predictable tool life The combination of carbide P25/P30 grades and diamond-ground cutting faces provides a balance between toughness and hardness that suits a broad range of general-purpose threading tasks. The specified carbide grades are chosen to reduce flank wear while maintaining edge security under interrupted cuts. This results in fewer insert changes, improved process stability and a measurable reduction in unexpected downtime for repetitive internal threading cycles. Design that supports secure clamping and accurate thread form A 10 x 10 mm square shank with a 140 mm overall length offers straightforward mounting in standard internal-tool holders and provides sufficient reach for many bore depths. The 60° tip geometry produces a standard metric thread form and helps to maintain pitch accuracy when combined with correct feed settings. The steel shank construction with fixed, diamond-ground carbide inserts ensures concentricity and repeatability, supporting consistent dimensional results across serial parts. Practical guidance for machining and set-up The right-hand cutting orientation suits conventional lathe spindle rotation and standard turning programmes. When setting up the tool, ensure the insert seat is clean and clamped to the holder to preserve the diamond-ground insert finish and to prevent micro-movement that would affect thread quality. Appropriate feeds and spindle synchronisation produce the intended 60° profile; the tool’s configuration is engineered to simplify set-up and to deliver predictable cutting behaviour in routine workshop environments. Where this tool is most effective This threading tool is intended for internal thread production where a standard 60° profile is required and where stable repeatability is a priority. The tool’s construction makes it well suited to batch operations where tool life and dimensional consistency matter. The designation WN283 and the solid combination of carbide specification and insert finish emphasise suitability for industrial use where operators require a robust, easy-to-integrate threading solution Contact Metav Werkzeuge for tailored advice on integrating the Wilke internal thread turning tool WN283 (SKU 4118655052NW) into production or to request current availability via info@metav-werkzeuge.com or +49 2822 7131930 Technical Data Article number: 4118655052NW Norm: WN283 Product type: Internal thread turning tool Manufacturer: Werner Wilke Zerspanungstechnik GmbH Facts Overall length: 140 mm Cross-section: 10 x 10 mm Tip angle: 60° Cutting direction: right Packaging unit: 5 Special features Carbide P25/P30 Steel shank with diamond-ground carbide inserts Right-hand 60° profile FAQ What materials is this internal thread turning tool suitable for? The internal thread turning tool with carbide P25/P30 is intended for general-purpose internal threading; the carbide grades provide a compromise between hardness and toughness for common workshop materials. Is the tool supplied ready-mounted on the shank? The tool is delivered as a steel shank fitted with diamond-ground carbide cutting inserts according to the product specification and ready for clamping in a compatible internal-tool holder. What is the standard thread form produced by the tool? The tool produces a 60° thread form suitable for standard metric internal threads when set up with appropriate feed and spindle synchronisation. How should the tool be clamped for best results? Secure clamping of the 10 x 10 mm square shank in a rigid internal-tool holder is recommended to preserve concentricity and to maintain the diamond-ground finish of the carbide insert. What is the SKU and norm designation for ordering and reference? Reference WN283, SKU 4118655052NW for ordering and specification checks; this identifies the Wilke internal thread turning tool with carbide P25/P30. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com