100mm 12 x 12mm Side Turning Tool Carbide P25/P30, Right-Hand, DIN 4980 (ISO 6) - Werner Wilke Zerspanungstechnik GmbH
Take advantage of the offset design, carbide P25/P30 cutting plates and the compact 12 x 12 mm cross-section for reliable right-hand turning in tight fixtures — order the side-turning tool directly via Metav Werkzeuge or request guidance from the consultants if required. Side-turning tool »Wilke« – DIN 4980 (ISO 6), 12 x 12 mm, carbide P25/P30, right-hand Side-turning tool for industrial turning tasks; an offset holder compliant with DIN 4980 (ISO 6) tailored to right-hand machining in confined set-ups. Carbide P25/P30 for long tool life Right-hand cutting for turning tasks 12 x 12 mm square cross-section Offset design for restricted access Consistent accuracy thanks to standardised interface and geometry The holder adheres to DIN 4980 (ISO 6), ensuring a standardised mounting and repeatable alignment across compatible toolposts. The 12 x 12 mm square cross-section provides a stable contact surface that reduces vibration and runout, which improves dimensional consistency on serial turned parts. For production environments this means predictable tool behaviour and fewer rejects. Durable cutting performance from high-grade carbide Equipped with carbide plates in P25/P30 grades, the assembly offers high wear resistance under typical machining loads. The choice of P25/P30 balances toughness and hardness for standard turning operations, resulting in sustained cutting edges and less frequent regrinding. Diamond‑ground surfaces on the cutting plates produce a clean initial edge, contributing to consistent surface finish and extended service intervals. Practical offset geometry for confined and stepped work The offset (abgesetzt) profile of the holder creates clearance for operations near shoulders or recessed features, allowing access where straight shanks would collide. With a compact 100 mm overall length, the tool combines reach with rigidity, making it suitable for medium-reach applications in toolrooms and production workshops that require both accessibility and control. Built for ease of assembly and predictable results The tool is supplied as a steel shank fitted with precision, diamond-ground cutting plates, reducing set-up time and ensuring a uniform cutting edge orientation. The standardised interface simplifies replacement routines and minimises machine downtime, supporting lean workshop processes where consistent cycle times and uptime are valued. Suitable for workshop and small-batch production environments Designed for machinists and maintenance engineers who demand reliable right-hand turning in compact fixtures, this turning holder supports efficient workflows without complex set-up procedures. The combination of standard conformity, robust cutting material and offset geometry addresses common bottlenecks in small-batch production and maintenance turning tasks. Discuss suitability with Metav Werkzeuge for application-specific advice or to secure compatible holders and inserts directly from our warehouse in Emmerich Technical data Article number: 4118640102NW Label: Seitendrehmeißel DIN 4980ISO6 12x12mm HM P25/P30 re. Wilke Product type: Seitendrehmeißel Manufacturer: Werner Wilke Zerspanungstechnik GmbH Data Overall length: 100 mm Cross-section: 12 x 12 mm Form: abgesetzt Standard: DIN 4980 (ISO 6) Cutting direction: right Special features Material: carbide P25/P30 Steel shank with diamond-ground carbide cutting plates fitted Offset design for restricted access SKU: 4118640102NW FAQ What is the standard interface of the turning holder? The holder conforms to DIN 4980 (ISO 6), ensuring compatibility with toolposts and fixtures designed for that shank profile. Which cutting material is fitted on the tool? The assembly is fitted with carbide P25/P30 cutting plates; these are diamond-ground for an accurate cutting edge and sustained wear resistance. Is this a right-hand or left-hand tool? This is a right-hand turning tool, specified for conventional right-hand cutting directions and applications. What are the key dimensions to check before purchase? Check the 12 x 12 mm cross-section and the 100 mm overall length to ensure the holder fits the intended toolpost and reaches the workpiece as required; SKU 4118640102NW identifies this configuration. Can this holder be used for confined shoulder turning? Yes, the offset design provides additional clearance for shoulders and recessed features, improving accessibility in confined turning tasks. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
100mm Side Turn Tool 12x12mm Carbide P25/P30 Offset Left DIN 4980 (ISO 6) - Werner Wilke Zerspanungstechnik GmbH
Take advantage of the combination of a carbide P25/P30 cutting edge, a 12 x 12 mm square shank and the standardized DIN 4980 connection for consistent side-turning results; order directly via Metav Werkzeuge or consult the technical team for compatibility and setup advice. Side turning tool DIN 4980 (ISO 6) 12 x 12 mm, carbide P25/P30, left-hand — Werner Wilke Side turning tool DIN 4980 (ISO 6) 12 x 12 mm, carbide P25/P30, left-hand is a stepped steel-shank tool fitted with diamond-ground carbide cutting plates for precise lateral turning operations in standard DIN 4980 toolholders. Carbide P25/P30 cutting plates 12 x 12 mm square shank Left-hand cutting orientation DIN 4980 (ISO 6) interface Durable carbide grade for reliable steel machining The tool is equipped with carbide plates in P25/P30, a grade optimised for common steel applications. The use of diamond-ground cutting plates ensures a consistent cutting geometry and long tool life, which reduces the frequency of regrinding or replacement. As a result, manufacturers and workshops benefit from predictable tool behaviour under repetitive lateral turning tasks, improving process stability and lowering unplanned stoppages. The delivered configuration suits routine finishing and semi-finishing operations where reproducible surface quality matters. Standardised connection and compact geometry for quick integration Conformity with DIN 4980 (ISO 6) means the insert-mounted tool integrates smoothly into compatible toolholders and lathe setups. The 12 x 12 mm cross-section and a stepped design provide a compact, rigid interface that facilitates clamping reproducibility and minimises deflection during side turning. The steel shank construction combines torsional stability with familiar mounting practices in industrial turning cells, enabling fast tool changes and reliable positioning without additional adaptors. Left-hand orientation and handling benefits for specific set-ups Designed as a left-hand lateral turning tool, this variant permits cutting actions when the tool must approach the workpiece from that direction, avoiding awkward re-fixturing or complex tool staging. The diamond-ground plates contribute to consistent chip formation and surface finish, supporting operators who require dependable results on repeat runs. This tool is therefore suited to production lines and job-shop environments where direction-specific operations and short-cycle repeatability are part of the daily workflow. Procurement confidence and practical support from Metav Sourcing through an experienced partner offers both logistical and technical reassurance. Metav’s role as a quality filter for the European market and its broad product range mean access to supplementary tooling and matched holders is straightforward. For customers seeking compatibility checks, mounting advice or batch supply planning, direct contact with Metav Werkzeuge’s consultants helps ensure the chosen side turning tool matches the existing toolholder architecture and production requirements. Contact Metav Werkzeuge to confirm compatibility with existing DIN 4980 toolholders, request a technical datasheet for this left-hand carbide side turning tool (SKU 4118640552NW) or arrange a tailored supply plan via info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: 4118640552NW Product: Side turning tool Label: Seitendrehmeißel DIN 4980ISO6 12x12mm HM P25/P30 li. Wilke Manufacturer: Werner Wilke Zerspanungstechnik GmbH Form: Stepped Standard: DIN 4980 (ISO 6) Facts Cross-section: 12 x 12 mm Overall length: 100 mm Packaging unit: 5 Special features Material: Carbide P25/P30 Steel shank with diamond-ground carbide cutting plates Left-hand cutting direction Stepped (offset) design Conforms to DIN 4980 (ISO 6) FAQ What materials is this side turning tool suited for? The side turning tool with P25/P30 carbide plates is intended primarily for steel machining and typical lateral turning tasks where ISO P-grade carbide is appropriate. How does the DIN 4980 connection affect integration? DIN 4980 (ISO 6) ensures compatibility with standard toolholders; the 12 x 12 mm square shank and stepped format enable straightforward clamping into compatible holders without special adaptors. Is this a left-hand or right-hand tool and why does it matter? This is a left-hand variant; left-hand orientation is required when the cutting approach and lathe setup demand tool movement from the opposite direction to a right-hand tool. What advantages do diamond-ground plates provide? Diamond-ground carbide plates deliver a consistent cutting edge and improved surface finish, which supports more predictable tool life and reproducible machining results. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
110mm 16x16mm Offset Right-Hand Carbide Insert Side Turning Tool DIN 4980 (ISO 6) - Werner Wilke Zerspanungstechnik GmbH
Combine carbide P25/P30 cutting tips with the 16 x 16 mm cross-section and DIN 4980 compatibility for dependable, repeatable side turning in series production. Order the tool directly via Metav Werkzeuge or consult their specialists for application guidance. Side turning tool – 16 x 16 mm, Carbide P25/P30, DIN 4980 (ISO 6) by Werner Wilke The Side turning tool is designed for precision external turning on lathes, offering a DIN 4980 (ISO 6) interface and diamond-ground carbide tips for consistent surface quality. Carbide P25/P30 diamond-ground tips 16 x 16 mm rectangular cross-section Right-hand cutting direction DIN 4980 (ISO 6) toolholder interface Consistent cutting accuracy for repeatable parts The side turning tool delivers steady cutting performance thanks to its carbide cutting plates in grade P25/P30, which are diamond-ground for precise geometry and low runout. This construction reduces variation between parts and shortens inspection cycles, so machining processes become more predictable. The combination of a robust carbide grade with an engineered cutting geometry supports controlled chip formation and stable cutting forces, which is particularly important for medium-run production where repeatability and component tolerances are critical. Fast integration with standard toolholders Compatibility with DIN 4980 (ISO 6) ensures straightforward mounting in standard toolholders, simplifying set-up and changeover procedures. The offset shank design allows accurate positioning of the cutting edge relative to the workpiece datum, reducing the need for repeated adjustments. For workshops managing mixed fleets of lathes, the standard interface cuts complexity and speeds up tool replacement, helping to maintain spindle uptime and reduce cumulative set-up costs over multiple shifts. Durable construction that lowers maintenance needs A steel shank fitted with diamond-ground carbide cutting plates provides a balance between rigidity and wear resistance. The selected carbide grades offer good edge stability under interrupted cuts and maintain a sharp profile over extended use, which lowers the frequency of insert changes and reduces toolroom workload. The right-hand cutting orientation is optimised for standard turning directions on most engines, enabling predictable tool life and simplified inventory management. Practical supply and workshop logistics Measurements are precise and clear: 16 x 16 mm cross-section and an overall length of 110 mm, supplied in packs of 5 for efficient restocking. These dimensions make the tool suitable for typical holder geometries while the compact packing reduces storage footprint. For production planning, the consistent specification aids in SKU control and reorder cycles; technical enquiries about specific machining tasks can be directed to Metav Werkzeuge for tailored recommendations. Secure reliable turning performance by sourcing the Wilke side turning tool through Metav Werkzeuge for dependable supply from Emmerich; enquiries can be sent to info@metav-werkzeuge.com or by telephone on +49 2822 7131930 Technical data SKU: 4118640152NW Product type: Side turning tool Brand: Werner Wilke Zerspanungstechnik GmbH Cross-section: 16 x 16 mm Overall length: 110 mm Cutting direction: right-hand Packaging unit: 5 Interface standard: DIN 4980 (ISO 6) Form: offset Facts Cross-section: 16 x 16 mm Overall length: 110 mm Packaging unit: 5 SKU: 4118640152NW Special features Carbide P25/P30 Diamond-ground carbide cutting plates Offset shank Steel shank DIN 4980 (ISO 6) interface Right-hand cutting direction FAQ Which toolholder fits this turning tool? The side turning tool is compatible with toolholders conforming to DIN 4980 (ISO 6); the tool is supplied as Side turning tool (SKU 4118640152NW) by Werner Wilke. What is the cutting direction of the tool? The tool has a right-hand cutting direction, specified for the Side turning tool (SKU 4118640152NW) from Werner Wilke. What are the dimensions of the cutting shank? Cross-section is 16 x 16 mm and overall length is 110 mm for the Side turning tool (SKU 4118640152NW) supplied by Werner Wilke. What material are the cutting plates made from? The cutting plates are carbide P25/P30, diamond-ground for edge stability and precise geometry on the Side turning tool (SKU 4118640152NW). How is the tool packaged for supply? The Side turning tool (SKU 4118640152NW) by Werner Wilke is supplied in packs of 5 for convenient workshop replenishment. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
125mm 20 x 20 Side Turning Tool Carbide P25/P30 Offset DIN 4980 (ISO 6), Left-Hand - Werner Wilke Zerspanungstechnik GmbH
Take advantage of the combination of diamond-ground carbide cutting plates and a DIN-compliant 20 x 20 shank for consistent, repeatable side turning. The offset design provides access in confined set-ups while the P25/P30 grades deliver a balanced wear resistance and toughness for general turning tasks. Order the tool directly via Metav Werkzeuge or ask the consultants for tailored advice. Wilke side-turning tool DIN 4980 (ISO 6) — 20 x 20 mm, carbide P25/P30, left-hand The Wilke side-turning tool is an offset lathe tool, fitted with diamond-ground carbide plates for precise side-facing and profiling operations where a DIN 4980 (ISO 6) shank is required Carbide P25/P30 cutting plates Offset shank for tight access DIN 4980 (ISO 6) standard shank 125 mm overall length, 20 x 20 shank Consistent edge quality for predictable cuts The steel shank is fitted with diamond-ground carbide plates in P25/P30, which means the cutting edges are shaped and finished to a high degree of precision. This results in a consistent cutting geometry and reduced runout at the tip, translating into stable chip formation and predictable surface finish. For workshops that depend on repeatability, the combination of a solid shank and precisely finished carbide inserts reduces variation between workpieces and limits the need for frequent re-adjustment. The emphasis here is on measurable process stability rather than marketing claims. Standardised shank for straightforward toolholding Compliance with DIN 4980 (ISO 6) provides clarity when selecting toolholders and fixtures: the shank dimensions follow an established standard for lathe tooling, making it simpler to verify clamp fit and set-up height. The 20 x 20 cross-section and the overall 125 mm length support common toolpost and turret systems used in general workshop and light industrial turning. Using a standard shank reduces setup time and the risk of incorrect mounting, which contributes directly to throughput and machining safety. Offset geometry and left-hand orientation for specific tasks The offset (abgesetzt) form allows the cutting tip to reach shoulders, grooves and other side-facing features that would be difficult with a straight profile. The tool’s left-hand cutting direction means it is intended for operations where the tool cuts when fed from right to left; this is important when planning tool layout for multi-station or multi-tool turning operations. Selecting left- or right-hand orientation according to the machining sequence prevents clashes and ensures that feeds and clearances work as intended. Robust construction aimed at workshop productivity The use of carbide plates on a rigid steel shank offers durability and reduced maintenance intervals compared with regrindable high-speed steel solutions. Diamond-ground plates maintain a consistent edge profile for longer, which reduces dressing frequency and supports uninterrupted production runs. The design prioritises functional resilience: fewer tool changes, reduced setup interventions and stable part quality all contribute to improved machine utilisation in everyday workshop practice. For advice on integrating Wilke carbide tooling into a current turning line or to place an order, contact Metav Werkzeuge in Emmerich for straightforward, expert guidance at info@metav-werkzeuge.com or call +49 2822 7131930 — Metav can assess compatibility and delivery options quickly Technical data Article number: 4118640652NW Product type: Side-turning tool Brand: Werner Wilke Zerspanungstechnik GmbH Facts Overall length: 125 mm Cross-section: 20 x 20 mm Packaging unit: 5 Special features Material: Carbide P25/P30 Form: Offset Standard: DIN 4980 (ISO 6) Steel shank with diamond-ground carbide cutting plates Left-hand cutting direction FAQ What materials are best machined with this side-turning tool? The Wilke side-turning tool is fitted with P25/P30 carbide plates; these grades offer a balanced combination of wear resistance and toughness suited to general turning tasks common in workshop environments. How does the DIN 4980 (ISO 6) shank help with set-up? DIN 4980 (ISO 6) standardisation ensures the 20 x 20 shank dimensions match common toolholders, simplifying clamping, height setting and toolholder selection for reliable mounting. What does left-hand orientation mean in practice? Left-hand orientation indicates the tool is intended to cut when fed from right to left; this affects tool placement and the sequence of operations to avoid collisions and ensure correct chip flow. Can the carbide plates be replaced or reconditioned? The design uses fitted diamond-ground carbide plates; replacement procedures depend on the holder design and workshop practices — spare plates and instructions are typically sourced via the supplier. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
125mm 20 x 20mm Side Turning Tool Carbide P25/P30 Offset DIN 4980 (ISO 6) - Werner Wilke Zerspanungstechnik GmbH
A robust choice for precise side turning: carbide P25/P30 inserts, a 20 x 20 mm cross-section and a stepped shank to DIN standard ensure consistent cutting performance and straightforward integration into existing toolholders — order directly via Metav Werkzeuge or consult the team for compatibility advice. Side turning tool DIN 4980 (ISO 6) 20 x 20 mm, carbide P25/P30, right-hand – Werner Wilke The side turning tool is a stepped-shank lathe tool designed for accurate external side cuts and finishing operations in general turning applications Carbide P25/P30 inserts for consistent performance Cross-section 20 x 20 mm for rigid mounting Right-hand cutting for standard turning operations Stepped shank to DIN 4980 (ISO 6) for compatibility Greater cutting consistency for reliable production The tool combines carbide P25/P30 cutting material with diamond-ground inserts, delivering stable edge geometry and predictable wear behaviour. This consistency reduces the need for rework and shortens cycle variability, which supports higher throughput in batch production. The right-hand cutting orientation is suited to the majority of conventional lathe setups, while the insert-grade maintains a balance between toughness and hardness for longer life in interrupted cuts. Fast integration and predictable setup times Compliance with DIN 4980 (ISO 6) and the 20 x 20 mm cross-section simplifies tooling logistics: the stepped shank fits standard toolholders without custom modification, reducing setup time and supporting repeatable clamping. The stepped (abgesetzt) design positions the cutting head reliably, so machine offsets remain consistent from one changeover to the next. For operations that demand steady process windows, this leads to fewer adjustments and quicker ramp-up to full production speed. Durability that keeps workshops running A steel shank fitted with diamond-ground carbide inserts provides a robust connection between the holder and the cutting edge, while the overall length of 125 mm gives sufficient reach for many external turning tasks without sacrificing rigidity. The construction is aimed at routine workshop use: reduced vibration through the rigid cross-section translates into improved surface finish and prolonged insert life. For procurement teams seeking predictable maintenance intervals, the component supports straightforward inventory and replacement strategies. Select the Werner Wilke side turning solution with its certified DIN 4980 (ISO 6) interface and carbide P25/P30 inserts — contact Metav Werkzeuge for expert advice and rapid supply from Emmerich. Technical data Article number: 4118640202NW Product type: Side turning tool Manufacturer: Werner Wilke Zerspanungstechnik GmbH Material: Carbide P25/P30 Cross-section: 20 x 20 mm Overall length: 125 mm Cutting direction: Right-hand Standard: DIN 4980 (ISO 6) Form: Stepped Packaging unit: 5 Facts Cross-section: 20 x 20 mm Overall length: 125 mm Packaging unit: 5 Special features Carbide P25/P30 cutting material Stepped shank for standard toolholders Diamond-ground carbide inserts mounted on steel shank Right-hand cutting orientation FAQ What materials is this tool suitable for? The side turning tool with carbide P25/P30 inserts is suitable for general turning tasks on common workshop steels and similar materials; tool life will vary with material hardness and cutting parameters. Is the stepped shank compatible with standard holders? Yes — the DIN 4980 (ISO 6) stepped shank ensures compatibility with holders designed for a 20 x 20 mm cross-section, enabling straightforward integration into existing setups. How long is the tool and what reach does it provide? The tool has an overall length of 125 mm, providing sufficient reach for most external side turning operations while maintaining rigidity. Are replacement inserts available for the tool? Replacement inserts in carbide P25/P30 grade are used on the tool; matching inserts should be specified to maintain the intended cutting performance. What is the SKU for ordering or reference? Reference SKU: 4118640202NW for the Werner Wilke side turning tool Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
140mm 25 x 25 Side Turning Tool Carbide P25/P30, Offset, DIN 4980 (ISO 6) - Werner Wilke Zerspanungstechnik GmbH
Take advantage of the combination of an offset shank, carbide P25/P30 cutting plates and DIN 4980 compatibility for reliable, precise external turning operations; order directly via Metav Werkzeuge or contact our advisors for specification support. Side-turning tool DIN 4980 (ISO 6), 25 x 25 mm, carbide P25/P30 by Werner Wilke The side-turning tool DIN 4980 (ISO 6) 25 x 25 mm is an offset, right-hand external turning tool designed for use in standard DIN 4980 (ISO 6) toolholders, suitable for precision lathe operations. Carbide P25/P30 inserts fitted Offset shank for clearance DIN 4980 (ISO 6) shank form 25 x 25 mm cross-section Precision external turning with robust carbide inserts The side-turning tool combines a steel shank with diamond-ground carbide cutting plates in grade P25/P30, yielding consistent cutting edges and predictable wear characteristics. The diamond grinding on the inserts improves surface contact and reduces the need for frequent adjustment, which translates into shorter setup times and steadier part finish during batch production. With an overall length of 140 mm and a clear 25 x 25 mm cross-section, the tool suits standard holders while offering the rigidity required for moderate to demanding external turning. The right-hand cutting direction is specified for typical lathe feed directions and avoids ambiguity during tool selection. Seamless compatibility with DIN 4980 toolholders Designed to the DIN 4980 (ISO 6) shank form and presented as an offset (abgesetzt) variant, the tool integrates directly with widely used lathe toolposts and indexable systems that accept this standard. Compatibility with the DIN 4980 standard simplifies procurement and replacement planning in production environments where interchangeability is essential. The offset geometry provides the necessary clearance between the cutting edge and workpiece shoulders or fixtures, reducing the risk of collision and enabling easier access to stepped profiles or close-to-flange turning tasks. The combination of standardised shank form and defined cross-section supports stable clamping and repeatable tool resets. Built for repeatable production and ergonomic handling A steel shank fitted with replaceable, diamond-ground carbide plates keeps maintenance straightforward: worn inserts can be exchanged without replacing the entire toolholder. The tool’s construction supports consistent repeatability in serial production, helping to reduce scrap and rework. Its format and balance aid in operator handling when mounting or changing tools, and the defined cross-section (25 x 25 mm) provides a robust contact surface in the toolholder, limiting vibration and enhancing surface finish. These attributes make the tool a pragmatic choice for workshops seeking durable, easy-to-service turning solutions. Material guidance and application overview The cutting plates are specified as carbide P25/P30, industrial grades suited to a broad range of turning tasks on steels and similar materials. The designation indicates a robust carbide grade intended for general steel machining operations while maintaining edge stability; diamond grinding improves chip control and edge conformity. As a right-hand, offset side-turning tool, it is optimised for conventional lathe feeds and external profiling; however, compatibility with specific steels, alloys or advanced materials depends on cutting parameters, insert geometry and machine rigidity. For tailored setup recommendations and cutting data, technical consultation is available to match tool grade and machining strategy to the intended application. For precision external turning with proven carbide inserts, request availability from Metav Werkzeuge and benefit from expert selection and fast supply from Emmerich. Technical data Article number: 4118640252NW Manufacturer: Werner Wilke Zerspanungstechnik GmbH Facts Overall length: 140 mm Cross-section: 25 x 25 mm Packaging unit: 3 Special features Carbide: P25/P30 Offset shank (abgesetzt) DIN 4980 (ISO 6) shank form Steel shank fitted with diamond-ground carbide inserts Right-hand cutting FAQ What material are the cutting plates made of? The cutting plates are manufactured from carbide P25/P30, supplied on the side-turning tool by Werner Wilke Zerspanungstechnik GmbH for stable cutting performance. Is this tool compatible with DIN 4980 toolholders? Yes, the tool follows the DIN 4980 (ISO 6) shank form, ensuring compatibility with holders that accept this standard shank profile. What are the dimensions and form of the tool shank? The side-turning tool has a 25 x 25 mm cross-section and an overall length of 140 mm, provided in an offset form for improved clearance. Can the cutting plates be replaced? The tool uses replaceable, diamond-ground carbide inserts in grade P25/P30, allowing replacement of worn plates without removing the shank from the machine. Is this tool suitable for left-hand turning tasks? This specific tool is specified as right-hand cutting; for left-hand operations a corresponding left-hand variant should be selected. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
140mm 25x25mm Side Turning Tool Carbide P25/P30 Offset Left DIN 4980 (ISO 6) - Werner Wilke Zerspanungstechnik GmbH
Combine carbide P25/P30 cutting edges, a stepped steel shank and DIN 4980 (ISO 6) compatibility for stable, repeatable left-hand finishing; order directly via Metav Werkzeuge or ask our consultants for application advice. Wilke Side turning tool DIN 4980 (ISO 6) – 25 x 25 mm, carbide P25/P30, left-hand A Wilke Side turning tool DIN 4980 (ISO 6) designed for precision external turning and finishing on a wide range of steels, featuring a stepped shank and diamond-ground carbide cutting inserts. Carbide P25/P30 cutting edges Stepped steel shank design Left-hand cutting direction DIN 4980 (ISO 6) compatible Consistent cutting performance for production environments The tool is built around carbide P25/P30 inserts that offer a reliable balance of wear resistance and toughness, enabling longer tool life in series turning. The diamond-ground cutting faces reduce vibration at cut entry, which improves surface finish and lowers rework rates. For production lines where cycle time and repeatability matter, the combination of a robust cutting grade and a secure insert seating delivers measurable productivity gains without complex setup routines. Stability and repeatability from the stepped shank A stepped steel shank provides firm clamping and accurate register to DIN 4980 (ISO 6), reducing axial play during heavy cuts. The 25 x 25 mm cross-section gives a rigid interface with standard toolholders, helping to maintain concentricity and geometric tolerances across multiple workpieces. This mechanical stability translates into fewer rejects and steadier process windows when machining external contours or shoulder faces on turned parts. Left-hand orientation and practical handling benefits Designed for left-hand cutting operations, the tool is suitable for facing or turning directions that require opposite-hand geometry. The offset (abgesetzt) shank allows access in restricted setups where a straight shank would interfere, improving tool reach without compromising clamping integrity. This configuration simplifies tool selection for asymmetric setups and reduces the need for special fixtures. Clear specification and application guidance Conforming to DIN 4980 (ISO 6) ensures compatibility with widely used toolholder systems, making the tool straightforward to integrate into existing tooling arrays. The steel shank fitted with diamond-ground carbide inserts is intended primarily for finishing and semi-finishing on common steels; the design supports consistent surface quality and repeatable dimensions in medium- to high-volume machining operations. Technical staff unfamiliar with carbide grades will find P25/P30 a pragmatic choice for mixed-production environments. For application advice or to secure supply of the Wilke side turning tool with carbide P25/P30 inserts, contact Metav Werkzeuge in Emmerich for specialist consultation and reliable delivery Technical data Article number: 4118640702NW Product name: Wilke Side turning tool DIN 4980 (ISO 6) 25 x 25 mm left-hand Material: Carbide P25/P30 Cross-section: 25 x 25 mm Overall length: 140 mm Cutting direction: Left-hand Standard: DIN 4980 (ISO 6) Packaging unit: 3 Facts Overall length: 140 mm Cross-section: 25 x 25 mm Packaging unit: 3 Special features Steel shank with diamond-ground carbide inserts Carbide grade P25/P30 Stepped (abgesetzt) shank design Left-hand cutting orientation FAQ What materials is this side turning tool suited for? This side turning tool with carbide P25/P30 inserts is intended primarily for turning and finishing common steels; consult Metav Werkzeuge for specific material recommendations. Is the tool compatible with standard DIN 4980 toolholders? Yes, the tool conforms to DIN 4980 (ISO 6) and is compatible with toolholders designed to that standard; the stepped shank ensures secure clamping. What is the cross-section and overall length of the tool? The tool has a 25 x 25 mm cross-section and an overall length of 140 mm, specified for stable mounting and reach in confined setups. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
16x16mm Side Turning Tool Carbide P25/P30 Offset Left DIN 4980 (ISO 6) - Werner Wilke Zerspanungstechnik GmbH
Take advantage of proven carbide performance and a DIN‑compliant stepped shank for stable clamping and repeatable results; the left‑hand cut and 110 mm overall length make this tool suitable for reverse turning and deeper operations. Order the part directly via Metav Werkzeuge or contact our consultants for application advice. Side‑turning tool DIN 4980 (ISO 6) 16 x 16 mm — carbide P25/P30, left‑hand (Werner Wilke) A side‑turning tool DIN 4980 (ISO 6) 16 x 16 mm designed for reliable external profiling and facing on lathes, featuring a stepped shank and diamond‑ground carbide cutting plates suited to industrial turning tasks Stepped shank, DIN 4980 (ISO 6) compatible Cross‑section 16 x 16 mm for stable clamping Left‑hand cutting direction for reverse machining 110 mm overall length for deep operations Consistent machining quality for production environments The Side‑turning tool DIN 4980 (ISO 6) 16 x 16 mm delivers consistent cut geometry thanks to its diamond‑ground carbide cutting plates in P25/P30 grade, which ensure high wear resistance and edge stability during repeated cycles. The stepped shank design increases clamping rigidity, reducing vibration and improving surface finish; DIN‑compliant shank dimensions also enable quick toolholder interchangeability across standard toolposts. For production lines where repeatability matters, this combination of precision and standard conformity reduces scrap rates and set‑up time. Longer service life and predictable maintenance intervals Fitted with carbide P25/P30, the turning tool is optimised for a balance between toughness and hardness, extending tool life on general steel turning operations. The material choice supports stable cutting in continuous use, which translates to fewer interruptions for tool changes and a lower total cost of ownership over time. The left‑hand orientation suits reverse or internal approach cuts, while the 16 x 16 mm cross‑section contributes to secure clamping and reduced deflection under load, helping maintain dimensional tolerances across batches. Straightforward compatibility and practical handling Compliance with DIN 4980 (ISO 6) offers clear mechanical compatibility with standard toolholders, simplifying procurement and stocking decisions. The stepped steel shank, equipped with carbide cutting plates, is easy to mount and index where applicable, and the 110 mm overall length provides extra reach for recessed or deeper turning tasks without compromising stability. For workshops transitioning between jobs, the standardised interface and robust carbide tips make process planning more predictable and reduce set‑up complexity. For ordering or technical advice on the carbide performance and compatibility of this side‑turning tool, contact Metav Werkzeuge for specialist guidance and procurement support Technical Data Article number: 4118640602NW Product type: Side‑turning tool Label: Seitendrehmeißel DIN 4980ISO6 16x16mm HM P25/P30 li. Wilke Manufacturer: Werner Wilke Zerspanungstechnik GmbH Facts Overall length: 110 mm Cross‑section: 16 x 16 mm Packaging unit: 5 Special features Material: carbide P25/P30 Stepped shank (abgesetzt) DIN 4980 (ISO 6) compatible Steel shank fitted with diamond‑ground carbide cutting plates Left‑hand cutting direction FAQ What materials is this turning tool suited for? The turning tool with carbide P25/P30 is suitable primarily for general steel machining; the carbide grade balances toughness and hardness for reliable performance in common turning applications. Is the shank compatible with standard toolholders? Yes, the stepped shank conforms to DIN 4980 (ISO 6), ensuring mechanical compatibility with standard holders that accept 16 x 16 mm shanks. What is the overall length and how does it affect reach? The overall length is 110 mm, offering increased reach for deeper or recessed turning tasks while maintaining clamping stability. Can this tool be used for reverse or left‑hand cuts? The tool is specified with a left‑hand cutting direction, making it suitable for reverse‑direction machining and specific facing or profiling operations. What is the article number for ordering and reference? The SKU for ordering and reference is 4118640602NW; include this when enquiring to ensure the correct side‑turning tool and configuration are supplied. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
90mm 10 x 10 Side Turning Tool Carbide P25/P30 Offset DIN 4980 (ISO 6) Right-Hand - Werner Wilke Zerspanungstechnik GmbH
Take advantage of the combination of durable carbide tips, a standardised DIN shank and a compact 10 x 10 profile for consistent, repeatable turning operations. Order the side turning tool directly via Metav Werkzeuge or ask our consultants if needed. Wilke side turning tool 10 x 10 mm (carbide P25/P30), right-hand The Wilke side turning tool is an offset, DIN 4980 (ISO 6) compliant carbide-tipped cutter designed for precise external turning on lathes and workshop machines. Carbide P25/P30 tips for consistent wear resistance Offset design for precise lateral cutting DIN 4980 (ISO 6) shank fit for standard toolholders Right-hand cutting direction for conventional turning Durable carbide tips for steady production results Equipped with carbide P25/P30 cutting tips, this tool offers high resistance to abrasive wear and stable edge life under regular lathe conditions. The diamond-ground carbide faces deliver a reliable cutting geometry that maintains dimensional accuracy across runs, reducing part rework. For operations where flank wear and repeatability determine throughput, the robust tip grade supports consistent cycle times and fewer insert changes. Standardised shank and offset geometry for reliable set-up The DIN 4980 (ISO 6) specification ensures a standardised fit with compatible toolholders, which supports quick tool changes and dependable clamping. The offset (abgesetzt) configuration increases clearance behind the cutting edge, preventing interference on complex profiles and aiding chip flow. With a compact 10 x 10 mm cross-section and 90 mm overall length, the shank provides a balance of rigidity and accessibility for tight workpiece geometries while keeping vibration low for better surface finish. Practical integration into workshop workflows Designed for routine workshop use, the tool is built on a steel shank fitted with precision-ground carbide cutting tips for straightforward replacement or servicing. The right-hand cutting direction suits conventional turning setups and makes the tool a direct fit for typical production sequences. Its construction minimises downtime through straightforward handling and compatibility with standard fixtures, contributing to a smoother workflow and predictable machining results. For reliable, repeatable turning with Wilke carbide tips contact Metav Werkzeuge in Emmerich by e‑mail at info@metav-werkzeuge.com or by phone on +49 2822 7131930 for ordering and technical advice. Technical data Article number: 4118640052NW Product type: Side turning tool Manufacturer: Werner Wilke Zerspanungstechnik GmbH Standard: DIN 4980 (ISO 6) Core data Cross-section: 10 x 10 mm Overall length: 90 mm Packaging unit: 5 Special features Carbide: P25/P30 Offset design (abgesetzt) Steel shank with diamond-ground carbide cutting tips Right-hand cutting direction FAQ What materials is the Wilke side turning tool suited for? The Wilke side turning tool is supplied with carbide P25/P30 tips; suitability for specific materials depends on cutting speeds and feeds, so recommended parameters should be checked against the workpiece material. Will this tool fit standard holders? Yes, the shank complies with DIN 4980 (ISO 6) and is intended for holders matching that standard, enabling straightforward mounting in many lathe toolposts and turrets. Is the tool suitable for CNC use? When mounted in a suitable holder that accepts DIN 4980 (ISO 6) shanks, the tool is appropriate for both conventional and CNC turning centres, subject to correct clamping and machining parameters. How are the carbide tips maintained or replaced? The tool features a steel shank with precision carbide cutting tips; replacement and maintenance follow standard workshop procedures—consult Metav Werkzeuge for spare parts and service guidance. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
90mm 10 x 10mm Offset Side Turning Tool Carbide P25/P30, DIN 4980 (ISO 6) Left-Hand - Werner Wilke Zerspanungstechnik GmbH
Take advantage of the combination of a carbide P25/P30 cutting tip, a compact 10 x 10 mm cross-section and a stepped steel shank for reliable left-hand side turning; order directly via Metav Werkzeuge or consult the product specialists if further integration details are required. Side turning tool DIN 4980 (ISO 6), 10 x 10 mm, carbide P25/P30 – Werner Wilke The Side turning tool DIN 4980 (ISO 6), 10 x 10 mm, carbide P25/P30 is a stepped side turning tool engineered for precise left-hand machining in standard DIN-compatible toolholders. Carbide grade P25/P30 tip 10 x 10 mm square cross-section DIN 4980 (ISO 6) interface Left-hand cutting direction Repeatable geometry for consistent production results The stepped design together with the DIN 4980 (ISO 6) interface provides a stable locating surface for toolholding systems and helps maintain repeatable cutting geometry across batches. A defined 10 x 10 mm cross-section ensures a predictable contact area in the holder, reducing setup variation. With a total length of 90 mm the tool achieves sufficient reach for many turning tasks without compromising rigidity, which supports steady cycle times and consistent tolerances. Durable tip and construction to lower maintenance needs Fitted with carbide P25/P30 cutting plates, the toolhead combines wear resistance with good fracture toughness for a wide range of turning operations. The steel shank is supplied assembled with diamond-ground carbide inserts, a finish that supports secure seating and accurate run‑out. These construction choices translate into longer intervals between insert changes and less unexpected downtime, contributing to improved overall equipment efficiency. Straightforward fitment and reliable cutting direction Compliant with the DIN standard, the tool is suitable for holders designed to accept the ISO 6 interface, simplifying retrofits or additions to existing tool racks. The left-hand cutting orientation is clearly defined for planning of workpiece clamping and toolpath direction in multi-spindle or reversing setups. As a compact side turning solution, the tool integrates cleanly into production lines where space and orientation are factors, while still delivering the rigidity expected from a stepped shank design. For assistance selecting the correct DIN-compatible toolholder or to discuss batch supply, contact Metav Werkzeuge for specialist advice and ordering support. Technical data Article number: 4118640502NW Label: Seitendrehmeißel DIN 4980ISO6 10x10mm HM P25/P30 li. Wilke Product type: Side turning tool Manufacturer: Werner Wilke Zerspanungstechnik GmbH UID: 4118640502NW Facts Total length: 90 mm Cross-section: 10 x 10 mm Packaging unit: 5 Special features Material: Carbide P25/P30 Form: Stepped Standard: DIN 4980 (ISO 6) Cutting direction: Left-hand Construction: Steel shank fitted with diamond-ground carbide cutting plates FAQ Is this tool compatible with standard DIN 4980 toolholders? Yes. The side turning tool is manufactured to DIN 4980 (ISO 6) and fits holders designed for the ISO 6 interface. What is the cutting orientation and how is it marked? The tool is a left-hand cutter; the orientation is specified on the product label and in the SKU 4118640502NW description. Which carbide grade is used for the inserts? Diamond-ground inserts of carbide P25/P30 are fitted to the steel shank to balance wear resistance and toughness. What advantages does the stepped form provide? The stepped (abgesetzt) design improves seating stability in the holder and reduces run‑out, which supports repeatable turning accuracy. How many pieces are supplied per pack? The product is supplied in a pack of 5, as indicated in the technical data. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com