20x20mm Right-Hand Hook Turning Tool Carbide P25/P30 6mm Cut Width, WN263 - Werner Wilke Zerspanungstechnik GmbH

Combine durable carbide P25/P30 cutting performance with a 6 mm grooving width and right-hand cutting for accurate, repeatable turning results; order the tool directly via Metav Werkzeuge or consult our specialists for application support.

Hook turning tool 20 x 20 mm, carbide P25/P30 — right-hand (Werner Wilke WN263)

The hook turning tool 20 x 20 mm, carbide P25/P30 is a right-hand grooving and turning implement engineered for stable, high-precision lathe operations in both production and workshop environments.

Carbide grades P25/P30 for high wear resistance
20 x 20 mm square section for stable mounting
6 mm grooving width for precise parting
Right-hand cutting, 210 mm overall length

Precise groove control for consistent parting quality

The combination of carbide P25/P30 and diamond-ground inserts delivers a consistent cutting edge that keeps groove geometry stable across runs. The tool’s defined 6 mm grooving width reduces secondary finishing and supports repeatable dimensional accuracy, which translates into fewer rejects and less rework. For technicians who monitor process capability, this configuration helps to maintain tight tolerances during medium- to high-volume turning tasks without sacrificing edge life.

Robust shaft geometry for vibration-free turning

A 20 x 20 mm square cross-section and a 210 mm overall length provide a rigid mounting interface that minimises chatter in the holder. The steel shank construction paired with the carbide cutting plates offers a secure clamping surface and improved tool stability, especially when machining interrupted cuts. Reduced vibration improves surface finish and extends the service life of the cutting edge, benefiting throughput and scheduling in busy workshops.

Practical design that integrates with standard setups

Equipped with diamond-ground carbide cutting plates, the tool is prepared for immediate use in compatible toolholders and is suited to routine grooving and finishing tasks on turning centres. The right-hand cutting orientation simplifies setup for standard lathe feed directions and helps to keep cycle times predictable. Clear marking of the designation and norm (WN263) supports fast identification in tool cabinets and simplifies inventory management for production planners.

Contact Metav Werkzeuge today for tailored advice on toolholders and application setup for the Werner Wilke hook turning tool WN263 (SKU 4118660202NW) — our team in Emmerich can recommend the optimal configuration for the task at hand

Technical data

• Article number: 4118660202NW
• Norm / Designation: WN263
• Product type: Hook turning tool (Hakendrehmeißel)
• Manufacturer: Werner Wilke Zerspanungstechnik GmbH
• UID: 4118660202NW

Core dimensions

• Overall length: 210 mm
• Cross-section: 20 x 20 mm
• Grooving width: 6 mm
• Cutting direction: Right-hand

Materials & special features

• Material: Carbide P25/P30
• Steel shank with diamond-ground carbide inserts
• Label: Hakendrehmeißel 20x20mm HM P25/P30 re. Wilke

FAQ

What groove width does the tool provide?
The grooving width is 6 mm, as specified for the hook turning tool WN263 (SKU 4118660202NW), suitable for accurate parting and controlled chip formation.

Is this tool limited to right-hand cutting only?
Yes, the tool has a right-hand cutting orientation; setups should match the lathe’s feed direction for correct chip flow and cutting geometry.

Which carbide grades are used and what is the benefit?
The tool uses P25/P30 carbide grades; these grades offer good wear resistance and edge stability for routine turning and grooving operations on typical workshop workpieces.

Which toolholder fits the 20 x 20 mm shank?
The square 20 x 20 mm shank is compatible with standard 20 x 20 mm toolholders and clamping blocks commonly used on lathes and turning machines.

Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com