140mm 10x10mm Right-Hand Indexable Grooving Tool Carbide P25/P30, 3mm Cut Width - Werner Wilke Zerspanungstechnik GmbH
Reliable chip control from carbide P25/P30 tips and a compact 10 x 10 mm cross-section ensure consistent right-hand turning performance; combine robust diamond-ground cutting plates with a 140 mm overall length for flexible toolholder compatibility — order directly via Metav Werkzeuge or consult our specialists for application advice. Hook turning tool WN263 – carbide P25/P30, 10 x 10 mm by Werner Wilke The Hook turning tool WN263 is a right-hand turning tool designed for precise internal and external profiling and grooving on conventional lathes and CNC turning centres. Solid carbide P25/P30 cutting tips 10 x 10 mm cross-section for standard toolholders Right-hand cutting direction for conventional turning 3 mm grooving width suitable for narrow cuts Precise cutting and reliable edge life for production use The combination of carbide P25/P30 cutting plates and a diamond-ground finish delivers a stable cutting edge that resists abrasion and maintains geometry over many passes. The design focuses on repeatable results in production environments where small variances in tool life can multiply into significant downtime. The 10 x 10 mm cross-section fits common mini toolholders, while the overall length of 140 mm provides sufficient reach for most toolpost setups. These attributes translate into fewer tool changes, reduced machine stops and steadier component tolerances. Designed for narrow grooving and controlled chip flow Equipped with a dedicated 3 mm grooving capability and a right-hand cut orientation, the tool enables clean entry and exit on narrow profiles, reducing burr formation and secondary finishing. The steel shank fitted with diamond-ground carbide cutting plates combines the rigidity of a stable holder with the wear resistance of premium carbide. In practice, this means cleaner surfaces and less reworking – a direct benefit for workshops aiming to improve throughput and surface quality on turned parts. Practical compatibility and workshop logistics The tool is supplied in a pack of 5, which supports batch replenishment without frequent ordering. Marked as WN263, the designation helps with straightforward inventory management and tool surface matching across toolrooms. The compact cross-section ensures compatibility with a wide range of clamping systems, and the robust carbide grade is suitable for general-purpose turning of common engineering materials. Where indexable or replaceable cutting plates are preferred, the diamond-ground finish aids consistent seating and alignment, simplifying insert changes and maintenance routines. Contact Metav Werkzeuge for matching toolholders, delivery options from Emmerich and expert advice on integrating the WN263 into production workflows. Technical data Article number: 4118660052NW Item name: Hakendrehmeißel 10x10mm HM P25/P30 re. Wilke Norm/designation: WN263 Manufacturer: Werner Wilke Zerspanungstechnik GmbH Facts Total length: 140 mm Cross-section: 10 x 10 mm Grooving width: 3 mm Packaging unit: 5 Special features Carbide grade: P25/P30 Right-hand cutting direction Steel shank with diamond-ground carbide cutting plates Suitable for profiling and narrow grooving FAQ What applications suit this hook turning tool? The hook turning tool WN263 by Werner Wilke is intended for narrow grooving and finishing profiles where a 3 mm cut width and a right-hand orientation are required, offering good edge stability for serial turning tasks. Is the cutting material solid carbide or an insert system? This product features carbide P25/P30 cutting plates mounted on a steel shank; the cutting edges are diamond-ground to ensure consistent seating and long tool life. Which toolholders are compatible with the 10 x 10 mm cross-section? Standard mini toolholders and compact clamping blocks that accept a 10 x 10 mm shank are compatible; this geometry enables flexible mounting in common lathe toolposts. How should the WN263 be stored to preserve the diamond-ground edges? Store the tools in their original packaging and avoid contact between cutting edges to maintain the diamond-ground surface; the pack of 5 supports organised stock rotation. Can the WN263 be used on hardened steels? The P25/P30 carbide grades are optimised for general turning and finishing; verify material-specific suitability against tool data sheets and machining parameters for hardened materials. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
160mm 12 x 12mm Right-Hand Carbide Grooving Tool 4mm Cut Width, WN263 - Werner Wilke Zerspanungstechnik GmbH
Take advantage of a carbide-tipped hook-style turning tool that combines the wear resistance of P25/P30 carbide with diamond-ground cutting tips for precise 4 mm grooving; the right-hand cut and a 160 mm steel shank ensure stable machining and consistent surface quality. Order the tool directly via Metav Werkzeuge or consult the Metav team for application-specific advice. Hook-style turning tool 12 x 12 mm HM P25/P30, right-hand (Wilke) — turning tool for precise grooving with diamond-ground carbide tips A Hook-style turning tool 12 x 12 mm HM P25/P30, right-hand (Wilke) designed for repeatable grooving and finishing operations where tool life and surface quality matter Solid carbide P25/P30 grade Diamond-ground carbide cutting tips Right-hand cutting direction 4 mm grooving capability Consistent groove quality through premium carbide and tip geometry The combination of P25/P30 carbide and diamond-ground cutting tips delivers high wear resistance and predictable tool performance. This construction minimises edge wear and maintains cutting geometry over longer runs, which reduces rework and improves first-pass yield. The 12 x 12 mm cross-section together with the 4 mm grooving capability offers controlled chip formation and repeatable groove width, making it suitable for operations that demand consistent dimensional accuracy and surface finish. Stable tool support for reduced vibration and accurate depths A solid steel shank and a total length of 160 mm provide the rigidity required for stable cutting conditions. The WN263 specification indicates compatibility with standard holder geometries, enabling secure clamping and reduced micro-movement during cutting. The result is lower vibration, improved surface integrity and more accurate groove depths, which contributes to longer insert life and fewer rejects in serial production environments. Efficient workshop integration and predictable maintenance intervals The tool’s inserted carbide tips and standardised geometry allow straightforward replacement and integration into existing turning tool setups. Predictable wear characteristics mean maintenance intervals can be planned, reducing unplanned downtime. The right-hand cutting orientation is optimised for conventional lathe feeds and supports effective chip evacuation. For workshop procurement, the tool is supplied in practical units to support stock planning and rapid replacement when required. For reliable workshop performance and expert advice on selecting the right Wilke hook-style turning tool for specific applications, contact Metav Werkzeuge at info@metav-werkzeuge.com or call +49 2822 7131930 Technical data SKU: 4118660102NW Norm: WN263 Label: Hakendrehmeißel 12x12mm HM P25/P30 re. Wilke Type: Hook-style turning tool Facts Overall length: 160 mm Cross-section: 12 x 12 mm Grooving width: 4 mm Packaging unit: 5 Special features Material: Carbide P25/P30 Cutting direction: Right-hand Steel shank with diamond-ground carbide cutting plates WN263 compatibility FAQ What materials is the tool suitable for? The hook-style turning tool with P25/P30 carbide tips is designed primarily for metal turning tasks and performs reliably when machining steels and similar materials where wear resistance is required. How wide are the grooves produced with this tool? The tool is specified for a 4 mm grooving width, providing a consistent slot dimension when used with appropriate feeds and stable clamping. Is the tool compatible with standard lathe holders? Yes, the tool’s geometry and WN263 compatibility allow secure mounting in common turning tool holders for stable operation. How are the cutting tips manufactured and what is the benefit? The cutting tips are diamond-ground carbide, which improves edge consistency and prolongs cutting life, resulting in more predictable machining and reduced frequency of tip changes. Which SKU should be ordered for this hook-style turning tool? Order SKU 4118660102NW for the Wilke hook-style turning tool with 12 x 12 mm cross-section and P25/P30 carbide tips. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
180mm Hakendrehmeissel 16x16mm Solid Carbide P25/P30 5mm Cut Width, Right-Hand - Werner Wilke Zerspanungstechnik GmbH
Benefit from a combination of P25/P30 carbide cutting heads, a rigid 16 x 16 mm shank and a 5 mm plunge width for reliable, repeatable turning results; order the tool directly via Metav Werkzeuge or consult our specialists for application advice. Hook turning tool 16 x 16 mm HM P25/P30 (right‑hand) — Werner Wilke precision turning chisel with carbide tips Hook turning tool 16 x 16 mm HM P25/P30 (right‑hand) is a right‑hand turning chisel designed for precision lathe operations where stable clamping and controlled plunge cutting are required. Solid carbide P25/P30 cutting heads Cross-section 16 x 16 mm for stable clamping 5 mm plunge width for precise grooving Right-hand cutting direction for lathe turning Consistent metal removal for production environments The tool delivers consistent cutting performance by combining a square 16 x 16 mm shank with hardened carbide heads in grades P25/P30, ensuring dimensional stability during continuous turning work. The 5 mm plunge width allows controlled material access for grooving and profiling operations, reducing the need for repeated passes. This configuration supports process reliability and helps maintain component tolerances in small-batch and serial production. Durable carbide construction reduces downtime Fitted with carbide cutting plates, the design prioritises wear resistance and predictable tool life. The specification P25/P30 refers to cemented carbide grades selected for a balance of toughness and hardness, making the tool suited to typical workshop turning tasks where edge retention and impact resistance matter. Diamond-ground faces on the inserts promote stable cutting edges and help achieve consistent surface finishes without frequent regrinding. Secure mounting and machine compatibility The square shank geometry provides secure seating in standard 16 mm tool holders, improving rigidity and vibration control during turning. With an overall length of 180 mm and a right‑hand cutting direction, the tool is compatible with conventional lathe setups that accept square shanks and right‑hand tools. The combination of shank stability and carbide tip design supports accurate, repeatable results in machining sequences. Practical handling and maintenance guidance Constructed as a steel shank equipped with diamond-ground carbide cutting plates, the tool is built for straightforward handling and inspection. Regular visual checks of the cutting edge and timely replacement of worn inserts extend service life and preserve part quality. Where a fine surface or tight tolerance is required, the carbide tips deliver consistent performance until replacement is necessary, simplifying maintenance planning for workshop teams. For reliable carbide performance from Werner Wilke and purchase assistance, contact Metav Werkzeuge in Emmerich — email info@metav-werkzeuge.com or call +49 2822 7131930 for personalised advice and order support. Technical data Article number: 4118660152NW Designation: WN263 Label: Hakendrehmeißel 16x16mm HM P25/P30 re. Wilke Manufacturer: Werner Wilke Zerspanungstechnik GmbH Core technical data Overall length: 180 mm Cross-section: 16 x 16 mm Plunge width: 5 mm Packaging unit: 5 Special features Material: Carbide P25/P30 Cutting direction: right‑hand Shank: steel shank with diamond-ground carbide cutting plates Standard/nominal: WN263 FAQ What cutting direction does this turning tool use? The tool features a right‑hand cutting direction; the Hook turning tool 16 x 16 mm HM P25/P30 (right‑hand) from Werner Wilke is therefore intended for right‑hand lathe operations. Which dimensions define the shank and reach? The tool has a square shank of 16 x 16 mm and an overall length of 180 mm, as stated for SKU 4118660152NW. What material are the cutting heads made from? The cutting plates are manufactured from P25/P30 cemented carbide, providing a balance between toughness and hardness for stable cutting performance. How wide is the plunge or grooving capacity? The tool offers a 5 mm plunge width, which supports precise grooving and controlled material removal in turning tasks. What construction details support durability? The device is a steel shank with diamond-ground carbide cutting plates, a combination that promotes edge stability and consistent wear characteristics for routine workshop use. Manufacturer: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
20x20mm Right-Hand Hook Turning Tool Carbide P25/P30 6mm Cut Width, WN263 - Werner Wilke Zerspanungstechnik GmbH
Combine durable carbide P25/P30 cutting performance with a 6 mm grooving width and right-hand cutting for accurate, repeatable turning results; order the tool directly via Metav Werkzeuge or consult our specialists for application support. Hook turning tool 20 x 20 mm, carbide P25/P30 — right-hand (Werner Wilke WN263) The hook turning tool 20 x 20 mm, carbide P25/P30 is a right-hand grooving and turning implement engineered for stable, high-precision lathe operations in both production and workshop environments. Carbide grades P25/P30 for high wear resistance 20 x 20 mm square section for stable mounting 6 mm grooving width for precise parting Right-hand cutting, 210 mm overall length Precise groove control for consistent parting quality The combination of carbide P25/P30 and diamond-ground inserts delivers a consistent cutting edge that keeps groove geometry stable across runs. The tool’s defined 6 mm grooving width reduces secondary finishing and supports repeatable dimensional accuracy, which translates into fewer rejects and less rework. For technicians who monitor process capability, this configuration helps to maintain tight tolerances during medium- to high-volume turning tasks without sacrificing edge life. Robust shaft geometry for vibration-free turning A 20 x 20 mm square cross-section and a 210 mm overall length provide a rigid mounting interface that minimises chatter in the holder. The steel shank construction paired with the carbide cutting plates offers a secure clamping surface and improved tool stability, especially when machining interrupted cuts. Reduced vibration improves surface finish and extends the service life of the cutting edge, benefiting throughput and scheduling in busy workshops. Practical design that integrates with standard setups Equipped with diamond-ground carbide cutting plates, the tool is prepared for immediate use in compatible toolholders and is suited to routine grooving and finishing tasks on turning centres. The right-hand cutting orientation simplifies setup for standard lathe feed directions and helps to keep cycle times predictable. Clear marking of the designation and norm (WN263) supports fast identification in tool cabinets and simplifies inventory management for production planners. Contact Metav Werkzeuge today for tailored advice on toolholders and application setup for the Werner Wilke hook turning tool WN263 (SKU 4118660202NW) — our team in Emmerich can recommend the optimal configuration for the task at hand Technical data Article number: 4118660202NW Norm / Designation: WN263 Product type: Hook turning tool (Hakendrehmeißel) Manufacturer: Werner Wilke Zerspanungstechnik GmbH UID: 4118660202NW Core dimensions Overall length: 210 mm Cross-section: 20 x 20 mm Grooving width: 6 mm Cutting direction: Right-hand Materials & special features Material: Carbide P25/P30 Steel shank with diamond-ground carbide inserts Label: Hakendrehmeißel 20x20mm HM P25/P30 re. Wilke FAQ What groove width does the tool provide? The grooving width is 6 mm, as specified for the hook turning tool WN263 (SKU 4118660202NW), suitable for accurate parting and controlled chip formation. Is this tool limited to right-hand cutting only? Yes, the tool has a right-hand cutting orientation; setups should match the lathe’s feed direction for correct chip flow and cutting geometry. Which carbide grades are used and what is the benefit? The tool uses P25/P30 carbide grades; these grades offer good wear resistance and edge stability for routine turning and grooving operations on typical workshop workpieces. Which toolholder fits the 20 x 20 mm shank? The square 20 x 20 mm shank is compatible with standard 20 x 20 mm toolholders and clamping blocks commonly used on lathes and turning machines. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
250mm 25x25mm Right-Hand Grooving Turning Tool Carbide P25/P30, 8mm Cut Width - Werner Wilke Zerspanungstechnik GmbH
Combining carbide P25/P30 cutting plates with a 25 x 25 mm cross-section and an 8 mm grooving width, this right‑hand hook turning tool offers precise, repeatable grooving and reliable tool life; order directly via Metav Werkzeuge or consult our specialists for application advice. Hakendrehmeißel 25x25mm HM P25/P30 re. Wilke — Right‑hand hook turning tool with carbide P25/P30 Hakendrehmeißel 25x25mm HM P25/P30 re. Wilke is a right‑hand turning tool designed for precise grooving and parting tasks where consistent cut geometry and tool life are essential Carbide P25/P30 cutting plates 25 x 25 mm robust cross-section Right‑hand cutting direction 8 mm grooving width for precise cuts Consistent grooving with industrial‑grade carbide Equipped with carbide P25/P30 cutting plates mounted on a steel shank, this hook turning tool delivers consistent groove profiles even in repetitive production runs. The designation WN263 denotes the standardised geometry that supports stable tool seating and repeatability; diamond‑ground carbide edges provide a sharper initial profile and reduce vibration, which translates into steadier surface finish and fewer reworks. Such characteristics are particularly relevant for turning operations requiring tight tolerances over long batches. Durable configuration reduces downtime The combination of a 25 x 25 mm cross‑section and the reinforced shank configuration increases stiffness at the cutting edge, lowering deflection during engagement. This stiffness, together with the wear resistance of P25/P30 grade carbide, extends the intervals between insert changes and maintenance, contributing to higher machine uptime. The tool’s build aims to provide an economical balance of tool life and cutting performance for medium‑duty steel turning and grooving operations. Easy adaptation to existing lathe setups Designed as a right‑hand tool with a 250 mm overall length, the component integrates smoothly into standard tool holders and turret stations. The 8 mm groove width is suitable for common parting and undercut profiles, allowing straightforward changeover from general‑purpose cutters without extensive fixture modification. Clear, measurable dimensions and standardised geometry mean predictable set‑up times and fewer trial cuts during process introduction. Practical performance across common workshop materials While optimised for steelwork, the tool’s carbide composition and ground cutting edges deliver reliable results across a range of applications where a robust grooving action is required. The tool’s geometry prioritises chip control and edge strength, reducing the risk of built‑up edge formation and ensuring stable performance in continuous turning cycles. The result is dependable surface quality and repeatability where production consistency matters. Quality assurance and application support Manufactured to a recognised tooling standard and supplied in practical packing units, the tool is aimed at workshops and production lines that require predictable behaviour and straightforward inventory management. The proven carbide grades and accessory specifications support quality‑centred workflows and help streamline procurement for precision turning operations. Contact Metav Werkzeuge for tailored advice on integrating this Wilke right‑hand hook turning tool into existing turning processes or for ordering information through Metav Werkzeuge. Technical data SKU: 4118660252NW Norm: WN263 Product type: Hook turning tool (right‑hand) Manufacturer: Werner Wilke Zerspanungstechnik GmbH Facts Total length: 250 mm Cross‑section: 25 x 25 mm Grooving width: 8 mm Packaging unit: 3 pcs Special features Material: Carbide P25/P30 Steel shank fitted with diamond‑ground carbide cutting plates Right‑hand cutting direction Label: Hakendrehmeißel 25x25mm HM P25/P30 re. Wilke FAQ What materials is the tool suitable for? The tool, specified as a right‑hand hook turning tool with carbide P25/P30, is intended primarily for steel turning and grooving applications while offering reliable performance on common engineering materials. How wide is the grooving cut with this tool? The grooving width is 8 mm, a dimension suitable for typical parting and undercutting tasks in workshop and light industrial settings. What standard or geometry does the tool conform to? The tool follows the WN263 geometry, providing consistent seating and predictable tool behaviour in compatible holders. What is the overall length and cross‑section of the tool? Overall length is 250 mm, with a 25 x 25 mm cross‑section providing stiffness and reduced deflection during cutting. Is the cutting edge pre‑finished? Yes, the cutting plates are diamond‑ground carbide, offering a sharp initial edge and improved surface finish. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com