Carbide indexable inserts for high‑performance metalworking
Carbide indexable inserts are wear‑resistant cutting elements designed to deliver economical, precise material removal across a wide range of workpieces, offering excellent balance between extreme wear resistance and the toughness required to withstand mechanical shocks. Used on toolholders such as cutters, turning tools and twist drills, they enable efficient machining of materials from soft non‑ferrous alloys to high‑strength steels by optimising cutting forces and thermal stability. For standard accessible contours external coolant is often sufficient, while deep holes, heavy cutting or machining of stainless steel and titanium alloys benefit from internal coolant channels to protect the cutting edge, improve chip control and extend insert life. Key advantages include high durability, consistent surface finish and reduced tool changeover times through the use of replaceable indexable inserts, carbide grades and toolholder systems.
9mm HSS-E Twist Drill DIN 338 ,short, 5% cobalt-alloyed, Type N - MetavCUT
Twist Drill – Short HSS‑E Type N, Ø 9 mm, 135°, 5% Cobalt‑Alloyed, DIN 338 (MetavCUT) The Twist Drill from MetavCUT is a short Type N drill for precise metalworking, especially suited to drilling hard and alloyed steels with a 135° tip angle. Short design for high stability 135° tip for hard materials Fully ground flutes for precise holes HSS‑E with 5% cobalt for heat resistance Conforms to DIN 338 for short drills Greater Precision through Short Design and Material Choice The short Execution reduces overhang and increases Stability, which is particularly beneficial when machining hard metals. Manufactured in HSS‑E with 5% Cobalt‑Alloyed composition, the tool offers improved heat resistance and wear behaviour compared with standard HSS. As a result, operators achieve cleaner holes and longer tool life when performing demanding Metalworking tasks on stationary or portable Drilling Machines. Clean Holes and High Runout Accuracy with Ground Geometry A Fully ground flute geometry produces very sharp cutting edges and excellent Runout Accuracy, ideal for precision applications. The Type N spiral geometry is the classic choice for Metal Drilling and generates reliable chip evacuation in many alloys. Note that ground drills can be more brittle than rolled variants, therefore using appropriate cooling and careful feed rates on tougher Materials is recommended to avoid breakage. Designed for Metalworking: Recommended Applications and Users This MetavCUT Twist Drill is intended for drilling Alloyed and Unalloyed Steel, Cast Iron, Non‑Ferrous Metals and certain Plastics; it is well suited to workshop technicians, maintenance teams and precision machinists. The short overall length and stable shank make it especially useful for operations requiring minimal deflection, such as jig and fixture work or when using a Hand Drill for controlled site repairs. 135° Point Angle: Faster Penetration and Better Centering in Hard Materials A 135° Point Angle helps reduce the tendency to wander on the surface of hard materials and shortens the initial penetration time compared with steeper points. This geometry lowers the cutting forces on the central tip and improves centring on Stainless Steel and other tough alloys, enabling more dependable starts and reducing the need for pilot operations in many cases. Standard Compliance and Practical Handling Notes Conforming to DIN 338 ensures consistent dimensions and interchangeability for short Twist Drills with cylindrical shank. The Standard Line manufacturing and the Fully Ground Shaft Execution ensure predictable performance across batches. For best results, pair the drill with appropriate coolant and moderate spindle speeds when working in high‑tensile steels; this preserves edge integrity and reduces the risk of chipping. Strong recommendation: choose the MetavCUT Twist Drill (Short Type N, HSS‑E) for demanding metal drilling tasks — for tailored advice or supplementary technical data contact METAV Werkzeuge by eMail: info@metav-werkzeuge.com, Tel: +49 2822 7131930, WhatsApp: +49 170 2837271 Technical Information Designation: Twist Drill Brand: MetavCUT SKU: 47090-FDA Diameter: 9 mm Point angle: 135° Type: Type N Execution: Short Colour: 5% cobalt-alloyed Material: HSS‑E Shaft execution: Fully ground Overall length: 125 mm Spiral length: 81 mm Model series: Standard Line Norm: DIN 338 For drilling machine: Drilling Machine (Hand Drill) Application: Drills for metal Packaging unit: 5 Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What are Twist Drills used for? The MetavCUT Twist Drill (Type N) is primarily used for machining high‑strength materials and larger drill diameters; its geometry allows straightforward regrinding and it withstands greater mechanical loads, making it a standard choice for robust Metalworking tasks. Which three drill types exist? Common categories are Metal drills, Wood drills and Stone/Concrete drills, and the MetavCUT Twist Drill belongs to the Metal drill group suited for ferrous and non‑ferrous Materials. Can the MetavCUT Twist Drill be used for wood? The MetavCUT Twist Drill can be used in Wood, but as a Metal drill it offers less guidance and a rougher finish than dedicated Wood drills; it is easier to resharpen and shows lower self‑feeding tendency compared with specialised wood brad point drills.
9mm HSS-G Twist Drill DIN 1869 ,extra long, bright finished - MetavCUT
Twist Drill by MetavCUT — 9 mm, 135° Tip, Extra Long, Bright Finished, HSS‑G, DIN 1869, Fully Ground Shank A Twist Drill designed for deep metal drilling with Drilling Machines and engineered for high precision and reduced feed force. Extra long design for deep drilling HSS‑G ground for faster metal cutting 135° tip geometry for hard materials Fully ground shank for high runout accuracy Conforms to DIN 1869 for demanding applications Faster drilling with lower feed force for efficient workflows The HSS‑G construction delivers up to 40% faster drilling while requiring 50% less feed force compared with conventional HSS drills, making it ideal where productivity matters. Designed as an extra long variant, this drill enables deeper hole depths and greater reach without sacrificing concentricity. For workshop and industrial use, the combination of high cutting speed and reduced operator exertion translates into measurable time savings and less operator fatigue. Reliable centring and clean holes even in tough alloys With a 135° tip angle and a ground flute geometry, this tool penetrates harder materials more effectively and reduces walking at the start of the hole. The CNC ground flutes provide sharp cutting edges and excellent runout accuracy, resulting in precise, burr‑reduced holes in Grauguss, legierten and unlegierten Stahl, and non‑ferrous metals. The geometry is optimised to support drilling in applications up to the material classes indicated by DIN 1869. Built for deep and difficult penetrations The extended overall length and a spiral length of 175 mm allow drilling where standard lengths fail, for example deep assemblies or awkward fixturing. The bright finished surface offers good chip evacuation characteristics in conjunction with appropriate coolant, while the fully ground shank ensures consistent clamping in chucks and reduced vibration. Use with a suitable Drilling Machine and controlled coolant flow for best results in prolonged or stationary operations. Who benefits and how to use it correctly Manufacturers, toolrooms and maintenance teams that require repeatable, precise holes in harder metals will value this design. For optimal life and performance, use stable fixturing, appropriate spindle speeds and coolant when working with high‑strength steels. Because ground HSS drills can be more brittle than rolled types, avoid excessive lateral loading and prefer stationary machine setups for deepest holes and continuous production runs. Strong recommendation: Choose the MetavCUT Twist Drill for precise deep‑hole metalworking — for technical advice or to confirm suitability for a specific application, contact METAV Werkzeuge for expert support via email info@metav-werkzeuge.com, phone +49 2822 7131930 or WhatsApp +49 170 2837271 Technical specifications Designation: Twist Drill Brand: MetavCUT SKU: 32090-FDA Diameter: 9 mm Tip Angle: 135° Execution: Extra long Total Length: 250 mm Spiral Length: 175 mm Material: HSS‑G Shank Execution: Fully ground Colour: Bright finished Application: Drills for metal For Drilling Machine: Drilling Machine Standard: DIN 1869 Model Series: Standard Line Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What is a Twist Drill used for and which materials suit this MetavCUT Twist Drill? The MetavCUT Twist Drill is primarily intended for drilling into metals; its HSS‑G composition and 135° tip make it especially suitable for alloyed and unalloyed steels, cast iron and non‑ferrous metals. Use in a properly set up Drilling Machine with cooling for best results. Which three general drill types exist? The three main drill categories are metal drills, wood drills, and stone/concrete drills; the MetavCUT Twist Drill belongs to the metal drill group and is optimised for metalworking tasks.
9mm HSS-G Twist Drill DIN 1869 ,extra long, bright finished - MetavCUT
Twist Drill — Twist Drill, Diameter 9 mm, 135° Tip, Extra Long, Bright Finished, HSS‑G, DIN 1869 The Twist Drill is an extra‑long HSS‑G drill bit for drilling machines, designed for deep metal drilling and precise holemaking in alloyed and unalloyed steels. Extra long design for deep drilling 9 mm diameter with 135° tip angle HSS‑G fully ground for precise bores Conforms to DIN 1869 for deep‑hole work Precision and material: ground HSS for clean metal holes The fully ground HSS‑G geometry delivers high concentricity and sharp cutting edges, producing clean, precise holes in metal. Grinding the flutes rather than rolling creates a sharper cutting profile, which reduces chatter and improves roundness when used with appropriate feed and coolant. This makes the bit particularly suitable for alloyed and unalloyed steel, cast iron and non‑ferrous metals where hole quality and dimensional accuracy are required. Deep drilling capability: extra length for difficult access With an extra long overall length and an extended spiral, this design allows drilling in deep parts or where access from the rear is restricted. The extended spiral assists chip evacuation during deeper cuts, reducing the risk of clogging. For tasks requiring long reach, the extra‑long execution provides the working length necessary without compromising guidance when used in a suitable drilling machine and with correct cooling. Tip geometry and performance: 135° for harder materials A 135° tip angle reduces the tendency to wander and shortens centring time on harder workpieces such as stainless steel. The larger tip angle reduces the aggressiveness of the lead, distributing cutting forces over a broader area and often requiring less feed force. For demanding materials, the combination of tip geometry and HSS‑G composition improves tool life when adequate coolant and a stable setup are used. Practical use and user group: suited for workshops and industrial settings This twist drill was developed for professional workshops and industrial users who need reliable deep drilling in metals. It is best applied in drilling machines under steady clamping and with cooling. Compared with rolled types, the ground version can be re‑sharpened more easily to renew cutting edges, making it advantageous for users who perform maintenance on tooling and value reproducibility and finish. Strong recommendation: Choose the MetavCUT Twist Drill in extra‑long HSS‑G execution for demanding deep metal drilling — for technical advice or to confirm suitability for a specific application, METAV Werkzeuge provides expert consultation: info@metav-werkzeuge.com, Phone +49 2822 7131930, WhatsApp +49 170 2837271 Designation: Twist Drill Brand: MetavCUT SKU: 33090-FDA Diameter: 9 mm Tip Angle: 135° Execution / Type: Extra Long Colour: Bright Finished Material: HSS‑G Shaft Execution: Fully Ground Spiral Length: 220 mm Overall Length: 320 mm Standard: DIN 1869 Application: Drills for Metal Model Series: Standard Line For Use In: Drilling Machine Manufacturer: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What is the MetavCUT Twist Drill used for? The MetavCUT Twist Drill is primarily applied for drilling high‑strength workpieces and larger diameters in metal; its extra‑long HSS‑G design and DIN 1869 specification make it suitable for deep drilling where extended reach and durable cutting performance are required. Which three drill types exist? Common categories are Metal drills, Wood drills and Masonry/Concrete drills; the MetavCUT Twist Drill belongs to the metal drill category and is optimised for metalworking tasks. For what is a Twist Drill mainly used? A Twist Drill is mainly used for machining high‑strength materials and larger hole diameters; its form allows straightforward resharpening and it withstands higher loads in demanding applications. Why are twist drills pointed? The point reduces the cross‑edge at the tip of the Twist Drill, significantly lowering friction and feed forces while improving centring in the workpiece; a pointed geometry therefore eases penetration and enhances accuracy.
9mm HSS-G Twist Drill DIN 1869 ,extra long, bright finished - MetavCUT
Twist Drill — Extra Long Twist Drill, 9 mm, 135° tip, HSS‑G, Bright Finished (MetavCUT) The Twist Drill is an extra‑long HSS‑G drill designed for deep metal drilling with a 9 mm diameter and a 135° tip for hard materials. Extra‑long design for deep, hard‑to‑reach holes 9 mm Diameter for precise metal drilling 135° Tip angle optimised for harder materials HSS‑G ground for fast, clean cuts DIN 1869 compliant for demanding deep‑hole work Precision and performance for deep metal holes The MetavCUT extra‑long HSS‑G twist drill combines a generous overall length with a long Spiral to enable deep‑reach drilling where standard lengths fall short. Thanks to the fully ground flute geometry, the bit produces very sharp cutting edges and high run‑out accuracy, which results in cleaner, more precise holes in metals. For workshop and industrial environments this means fewer re‑cuts, improved fit‑up of components and more predictable machining results under challenging conditions. Faster cutting with less feed force The ground HSS‑G material and optimised geometry allow up to 40% faster drilling and require up to 50% less feed force compared with conventional HSS drills. This makes the tool especially effective when working with alloyed and unalloyed steel, cast steel, cast iron and non‑ferrous metals. The 135° tip angle reduces initial cutting resistance and improves centring on harder materials, shortening set‑up time and increasing throughput on serial operations. Reliable choice for demanding standards and deep drilling Conforming to DIN 1869, this twist drill is built for deep‑hole applications and tougher conditions. The Spiral length of 280 mm and total length of 410 mm are tailored for situations that require extended reach without compromising hole quality. Because the flutes are formed by CNC grinding rather than rolling, users benefit from superior surface finish and dimensional accuracy—features that matter when subsequent machining or assembly demands tight tolerances. Practical workshop guidance and safe use When using this extra‑long Twist Drill in tougher materials, stationary mounting and adequate cooling are recommended to avoid brittle fracture and to extend tool life. The fully ground shank supports better clamping accuracy in chucks and collets, reducing vibration and ensuring concentricity. For operators less familiar with deep‑hole techniques, using modest spindle speeds, steady feed and cutting fluid will deliver the best balance between speed and tool life. Who benefits from this tool This drill is aimed at metalworkers, toolrooms and maintenance professionals who require extended reach and high‑quality holes in harder materials. Whether producing components in small series or performing repair work on assemblies where access is limited, the MetavCUT twist drill offers a practical combination of depth capability and metal‑cutting performance. Strongly recommended: the MetavCUT extra‑long HSS‑G Twist Drill for reliable deep metal drilling — for technical advice or application support contact METAV Werkzeuge; we provide comprehensive consultation and sample guidance via eMail: info@metav-werkzeuge.com, Phone: +49 2822 7131930, WhatsApp: +49 170 2837271 Technical data Designation: Twist Drill Brand: MetavCUT Model series: Standard Line Diameter: 9 mm Total length: 410 mm Spiral length: 280 mm Tip angle: 135° Material: HSS‑G Standard: DIN 1869 Execution: Extra long Colour: Bright finished Shaft finish: Fully ground Suitable for: Drilling Machine / Hand drill Application: Drills for metal Manufacturer: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What materials is the MetavCUT Twist Drill best suited for? The MetavCUT Twist Drill (extra‑long HSS‑G Twist Drill) is particularly suited to alloyed and unalloyed steel, cast steel, cast iron, sintered iron, malleable iron, non‑ferrous metals and hard plastics, offering robust performance where higher strength and precision are required. Is the MetavCUT Twist Drill suitable for very deep holes? Yes, the MetavCUT extra‑long Twist Drill is designed for deep holes: its extended overall length and the Spiral length make it suitable for deep‑reach applications, and compliance with DIN 1869 underlines its suitability for demanding drilling tasks. For what is a Twist Drill used? It is mainly used for machining high‑strength materials and large bore diameters. This design is easy to resharpen and withstands higher loads. Which three drill types exist? There are metal drills, wood drills and stone/concrete drills. Why are Twist Drills tipped/sharpened? Sharpening reduces the secondary cutting edge at the tip of the Twist Drill, lowering friction forces and thus requiring less feed force while improving centring in the workpiece. Can a metal Twist Drill be used to drill wood? A metal drill can be used in wood but gives poorer guidance and a less clean result; it is easier to regrind and has lower self‑feeding characteristics. For which depths is the Twist Drill the most used tool? A full‑bore hole is made with a Twist Drill. For diameters up to 20 mm and depths up to 100 mm, the Twist Drill is the most commonly used tool.
9mm HSS-G Twist Drill DIN 338 ,left cutting - MetavCUT
Twist Drill — Profi Line left-cutting HSS-G 9 mm, 135° (DIN 338) by MetavCUT The Twist Drill left-cutting HSS-G 9 mm is a metal drill bit designed for use in drilling machines and hand drills for efficient extraction and precise metal drilling. Left-cutting geometry for screw extraction and tough tasks 9 mm Diameter for standard metal drilling 135° Tip angle for harder materials like stainless steel HSS-G Material for wear resistance and durability Conforms to DIN 338 for short twist drills with cylindrical shank Superior Performance in Hard Materials thanks to the 135° Tip Angle The Profi Line short twist drill features a 135° tip angle, which reduces entry forces and shortens the pilot time when penetrating harder materials. This geometry is particularly advantageous for stainless steel and other high-strength alloys because it spreads cutting load and decreases the risk of tip wandering. The result is cleaner holes and improved centring in demanding Metal applications. One direct advantage for workshops is fewer rejects and less rework when machining tougher components. Left-cutting Design: Fast Extraction and Lower Feed Force A left-cutting grind means the bit is ground to cut when the spindle turns counterclockwise; this is ideal for removing broken or seized screws and studs. The MetavCUT left-cutting twist drill is optimised for such operations and, according to the manufacturer data, can achieve up to 40% faster drilling while requiring up to 50% less axial feed force compared with conventional HSS drills. For technicians, this translates into reduced operator strain and faster job turnaround when working on repair or disassembly tasks. Material and Standard: HSS-G and DIN 338 for Reliable Use Manufactured from HSS-G, this drill offers a balance of toughness and heat resistance suited for sustained metal cutting. The product is made to DIN 338, the standard describing short twist drills with a cylindrical shank; this ensures consistent shank dimensions, compatible fitting in standard chucks, and predictable performance across production workflows. For buyers this means reliable interchangeability in tool holders and consistent hole quality in serial work. Where this Drill Excels and Who Benefits Most This twist drill is aimed at professionals and maintenance technicians who work with both alloyed and unalloyed steels, cast steels, cast iron, sintered metals, non-ferrous metals and hard plastics. Its left-cutting version is especially useful in repair shops and assembly lines where removal of broken fasteners is frequent. The Profi Line series positions the bit as a practical choice for workshops that require a robust, short drill with dependable centring and reduced push-down effort. For demanding metalwork choose the MetavCUT Profi Line Twist Drill for reliable extraction and efficient drilling — METAV Werkzeuge offers expert advice and comprehensive support, contact via eMail: info@metav-werkzeuge.com, Phone: +49 2822 7131930, WhatsApp: +49 170 2837271 Technical Information Designation: Twist Drill (Spiralbohrer) Brand: MetavCUT SKU: 60090-FDA Diameter: 9 mm Tip Angle: 135° Execution: left-cutting (linksschneidend) For: Drilling Machine / Hand Drill Material: HSS-G Standard: DIN 338 Model Series: Profi Line Packaging unit: 5 Application: Drills for metal Manufacturer: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What is the Twist Drill used for? The MetavCUT Twist Drill is primarily applied to the machining of high-strength materials and larger drill diameters; it is especially suited for alloyed and unalloyed steel, cast steel, cast iron, sintered iron, malleable iron, non-ferrous metals and hard plastics. Its shape allows relatively simple resharpening while maintaining resistance under heavy loads. Which three drill types are there? Commonly distinguished drill types are metal drill bits, wood drill bits and masonry/concrete drill bits. The MetavCUT Twist Drill belongs to the metal drill bit group. Why are twist drills resharpened at the tip? Resharpening the tip of a twist drill reduces the cross-cut edge at the point. By regrinding the point, friction is significantly lowered and less feed force is required; at the same time the bit centres more reliably in the workpiece. Can a Twist Drill be used to drill wood? A metal twist drill such as the MetavCUT Twist Drill can be used in wood, but guidance is inferior and hole quality is usually less clean than with a dedicated wood bit. Metal bits are easier to resharpen and typically exhibit lower self-feeding tendencies. For which drilling depths is the Twist Drill most used? A through hole in solid material is typically produced with a twist drill. For diameters up to 20 mm and drilling depths up to 100 mm, the twist drill is the most commonly used tool. What is better, HSS or HSSE? The common belief that HSSE steels are always superior to standard HSS steels is not universally correct. When choosing between HSS and HSSE, evaluate whether the specific working conditions justify the higher acquisition cost of HSSE.
9mm HSS-G Twist Drill DIN 338 ,short, bright finished, Type N - MetavCUT
Twist Drill — MetavCUT Basic Line, 9 mm, 135° Tip, HSS‑G (Short, Bright Finished, DIN 338) The Twist Drill is a short HSS‑G metalworking drill designed for Drilling Machines and handheld use, offering high feed efficiency and stable performance in demanding steel applications. Short design for stable, precise drilling 9 mm diameter for common metalworking tasks 135° tip for improved centring in hard materials Fully ground shank for accurate seating in chucks Conforms to DIN 338 for short twist drills Faster penetration and reduced feed effort for hard metals The HSS‑G composition delivers a clear advantage: up to 40% faster drilling and roughly 50% less thrust compared with conventional HSS bits. For users working with alloyed and unalloyed Steel, Cast Steel, Gusseisen and hard plastics, this means fewer tool changes and smoother cycles. The 135° tip angle reduces the tendency to wander on tough surfaces and shortens dwell during initial engagement. This results in more efficient machining and less operator fatigue. Short geometry for superior stability and hole quality A short overall length and a spiral length of 81 mm minimise overhang and vibration, producing more consistent hole geometry under moderate cutting conditions. The fully ground shank ensures solid clamping in chucks and better concentricity, improving finish and reducing runout. Because the flute length and geometry follow DIN 338, workshop operators benefit from predictable behaviour when switching between comparable short twist drills. Built for metalworking workshops and maintenance tasks This Type N twist drill is the classic choice for metal applications and is optimised for Drilling Machines as well as robust handheld units. Its bright finished surface eases chip evacuation in many metals while remaining straightforward to resharpen when needed. For maintenance engineers, toolroom technicians and small fabrication shops, the combination of 9 mm diameter and short design strikes a balance between versatility and rigidity. Industry standard compliance delivers reproducible results Manufactured to DIN 338 specifications within the MetavCUT Basic Line, this twist drill follows proven dimensional and performance criteria for short cylinder‑shank bits. The Type N normal spiral provides a versatile chip geometry for a wide range of metallic materials. If uncertainty remains about the correct geometry or material choice for a specific application, the short tip geometry and HSS‑G grade allow straightforward regrinding while maintaining performance. We recommend the MetavCUT Twist Drill from the Basic Line for precision metalworking where stability and efficient penetration matter most — for technical questions or selection support contact METAV Werkzeuge for expert advice: info@metav-werkzeuge.com | +49 2822 7131930 | WhatsApp +49 170 2837271 Technical Data Bezeichnung: Twist Drill Marke: MetavCUT SKU: 27090-FDA Durchmesser: 9 mm Spitzenwinkel: 135° Typ: Type N Ausführung: short Farbe: bright finished Material: HSS-G Schaft Ausführung: fully ground Gesamtlänge: 125 mm Spirallänge: 81 mm Anwendung: Drills for metal Norm: DIN 338 Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What materials is the MetavCUT Twist Drill suitable for? The MetavCUT Twist Drill (Type N, HSS‑G) is primarily intended for metalworking; it performs well in alloyed and unalloyed Steel, Cast Steel, Gusseisen and certain hard plastics, offering reliable penetration and chip formation for these materials. How does the short design of the MetavCUT Twist Drill benefit workshop use? A short Twist Drill from MetavCUT reduces overhang and vibration, improving hole accuracy and concentricity; the compact geometry is especially helpful for precise operations and when working with harder materials where deflection must be minimised. For what is a Twist Drill used? A Twist Drill is mainly employed for machining high‑strength materials and larger drill diameters; this form is easy to resharpen and endures higher loads. Which three drill types exist? The main categories are Metal Drills, Wood Drills and Stone/Concrete Drills. Why are Twist Drills sharpened at the tip? Tip sharpening reduces the cross‑cut at the drill tip, lowering friction and thus reducing required feed force while improving centring in the workpiece. Can a Twist Drill be used to drill wood? A Metal Drill can be used in wood, but guidance and finish are inferior compared with dedicated wood drills. Metal drills are easier to resharpen and show less self‑feeding tendency. For which drilling depths is the Twist Drill most commonly used? Twist Drills are the standard choice for through‑hole drilling. For diameters up to 20 mm and depths up to 100 mm they are the most frequently used tool. Is HSS better than HSSE? The common belief that HSSE is always superior to HSS is incorrect; selection should consider the specific working conditions and whether the extra cost of HSSE is justified. Sind Sie sich nicht sicher, ob dieses Werkzeug Ihre Anforderungen erfüllt? Oder benötigen Sie ergänzende technische Daten? Kein Problem – wir stehen Ihnen gerne zur Verfügung. 📧 eMail: info@metav-werkzeuge.com ☎️ Telefon: +49 2822 7131930 ✔️ WhatsApp: +49 170 2837271
9mm HSS-G Twist Drill DIN 338 ,short, bright finished, Type N - MetavCUT
Twist Drill — Type N, 9 mm, 135° tip, short, bright finished, HSS-G, DIN 338 (MetavCUT) A short, precision Twist Drill Type N designed for metalworking with a 9 mm diameter and a 135° point angle for stable, clean drilling in hard materials. Short design for higher stability HSS‑G ground for fast, precise drilling 135° point for hard materials like stainless steel Conforms to DIN 338 for short cylindrical drills Fully ground shank for excellent concentricity Durable HSS‑G construction for reliable metalworking The HSS‑G material offers a balance of hardness and edge retention that benefits demanding metalworking tasks. Built as a ground High Speed Steel tool, this short drill delivers sharp cutting edges and high runout accuracy, which reduces burr formation and improves hole quality. For users who prioritize precision, the ground geometry translates into cleaner bores and fewer reworks, while the bright finished surface aids chip evacuation during cutting. Short design increases stability and precision A reduced overall length and a shorter Spiral length improve stiffness during drilling, so less bending occurs under load. This compact geometry is particularly useful when machining legiertem und unlegiertem Stahl and other hard metals, where a rigid tool axis is essential. The shorter overhang results in increased feed stability, enabling higher feed rates in many setups without sacrificing hole accuracy. 135° tip and Type N spiral for hard materials The 135° point angle is tailored to cut into harder materials with reduced tendency to wander at entry, making it suitable for stainless steel and other tougher alloys. As a Type N (normal spiral) configuration, the tool is optimized for metal drilling rather than soft substrates. For less experienced users: a larger tip angle decreases the initial cutting aggressiveness and improves centering, which helps when starting holes in tough components. Precise shank and DIN 338 compliance for machine use With a fully ground shank, the drill provides excellent concentricity and grip in standard drill chucks and toolholders, reducing runout and wear. Conformance to DIN 338 ensures standardized dimensions and compatibility with common tool setup procedures in production and workshop environments. These characteristics make the tool well suited to both stationary machines and portable drilling machines used in metal fabrication. Who benefits and recommended applications Mechanical workshops, toolrooms and production engineers working with steels, cast materials and non‑ferrous metals will find the short Twist Drill especially advantageous for precision holemaking. Its properties support drilling in components where surface finish and positional accuracy matter. For simple explanations: HSS‑G denotes a ground High Speed Steel drill, Type N indicates the classic metal spiral, and the 135° tip suits harder substrates. Strong recommendation: For precision metal drilling choose the MetavCUT short Twist Drill Type N with HSS‑G ground geometry — METAV Werkzeuge offers expert advice and technical support if needed. If unsure whether this tool meets specific requirements or if additional technical data is required, please contact us — 📧 info@metav-werkzeuge.com | ☎️ +49 2822 7131930 | ✔️ WhatsApp +49 170 2837271 Designation: Twist Drill Brand: MetavCUT SKU: 45090-FDA Diameter: 9 mm Point angle: 135° Type: Type N Execution: short Overall length: 125 mm Spiral length: 81 mm Shank execution: fully ground Material: HSS-G Finish: bright finished For drilling machine: Drilling Machine Application: Drills for metal Model series: Standard Line Norm: DIN 338 Colour: bright finished Manufacturer: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What is a Twist Drill used for and which materials suit the MetavCUT Type N drill? The Twist Drill by MetavCUT, Type N, is primarily used for drilling metal; it is ideal for legiertes und unlegiertes Stahl, Gussstahl, Gusseisen and non‑ferrous metals. The Type N spiral and HSS‑G ground geometry ensure reliable cutting in harder materials and give good hole quality in workshop and production settings. Which three drill types exist and where does the MetavCUT Twist Drill fit? Three common drill types are metal drills, wood drills and masonry/concrete drills. The MetavCUT Twist Drill is a metal drill (Type N) and is specifically engineered for use in metalworking rather than for wood or stone. Why is the tip of a Twist Drill sharpened and how does that help in practice? The tip sharpening reduces the cross‑cut edge at the drill point, lowering friction and required feed force. For the MetavCUT Twist Drill Type N this means easier entry, better centering and reduced heat generation, resulting in cleaner holes and longer tool life when combined with appropriate cooling. Can the MetavCUT Twist Drill be used for drilling wood? A metal drill such as the MetavCUT Twist Drill can be used in wood, but it will usually offer less guidance and a rougher finish than a dedicated wood drill. Metal drills are easier to resharpen and exhibit less self‑feeding, so they may require more careful positioning when used in timber.
9mm HSS-G Twist Drill DIN 338 ,short, bright finished, Type N - MetavCUT
Geringe Auskraglänge und geschliffene HSS-G-Geometrie sorgen für präzise, vibrationsarme Bohrungen in Stahl und Guss; der 135° Spitzenwinkel erleichtert das Anbohren harter Werkstoffe und reduziert das Ausbrechen. Nutzen Sie die Kombination aus Stabilität, schnellerer Vorschubrate und hoher Rundlaufgenauigkeit, und ordern Sie den Bohrer direkt über Metav als verlässlichen Partner. Spiralbohrer 9 mm HSS-G (kurz) – MetavCUT Profi Line Spiralbohrer 9 mm HSS-G (kurz) – MetavCUT Profi Line eignet sich für präzise Metallbohrungen an stationären und handgeführten Maschinen und wurde nach DIN 338 für kurze Spiralbohrer ausgelegt. Kurze Ausführung für erhöhte Stabilität HSS-G geschliffen für saubere Bohrlöcher 135° Spitzenwinkel: besseres Anbohren von Edelstahl Zylinderschaft, passend für Handbohrmaschine DIN 338 Klassifikation, Profi Line Qualität Präzise Bohrleistung für harte Werkstoffe Die kurze Bauform reduziert die Auskraglänge und erhöht so die Stabilität beim Bohren. Bei gleicher Bohrungsgröße führt die verringerte Hebellänge zu weniger Vibrationen und verbessertem Rundlauf, was saubere und maßhaltige Bohrlöcher zur Folge hat. Die geschliffene HSS-G-Geometrie sorgt für sehr scharfe Schneiden und ermöglicht ein bis zu 40 % schnelleres Bohren bei gleichzeitig 50 % geringerer Anpresskraft gegenüber herkömmlichen HSS-Ausführungen, besonders in legierten und unlegierten Stahlgüten. Passgenau für Werkstatt und Montage Diese Ausführung wurde für den Einsatz an stationären Bohrmaschinen und für handgeführte Geräte konzipiert. Die Kombination aus Zylinderschaft und kurzer Gesamtlänge macht den Bohrer kompatibel mit typischen Spannfuttern und erhöht die Sicherheit bei der Anwendung. Anwender in Werkstatt, Montage und Instandhaltung profitieren von der einfachen Handhabung und der schnellen Verfügbarkeit des passenden Werkzeugs für Serien- und Einzelteile. Materialwahl, Geometrie und Normen für professionelle Ansprüche Der Bohrer besteht aus HSS-G (Schnellarbeitsstahl, geschliffen) und entspricht der DIN 338, die kurze Spiralbohrer mit Zylinderschaft klassifiziert. Die geschliffene Fertigung bringt sehr hohe Rundlaufgenauigkeit und scharfe Schneiden, wodurch besonders präzise Bohrungen in Gussstahl, Gusseisen und Nichteisenmetallen möglich sind. Hinweis: Geschliffene HSS-Werkzeuge können spröder sein; Kühlung und stationären Einsatz erhöhen die Standzeit. Zielgruppen und typische Einsatzbereiche Entwickelt für Anwender, die präzise Metallbohrungen benötigen: Industrie, Fachbetrieb und anspruchsvolle Heimwerker. Der Typ N mit Normalspirale ist speziell für Metallbearbeitungen wie Stahl, Temperguss und Hartkunststoff ausgelegt. Für sehr tiefe Löcher oder hochgehärtete Stähle sind andere Werkzeuge sinnvoll; für standardmäßige Bohrungen bis zu mittlerer Tiefe bietet dieses Produkt jedoch ein hervorragendes Verhältnis aus Präzision und Wirtschaftlichkeit. Empfehlung: Für präzise Metallbohrungen die Profi Line von MetavCUT wählen und technische Beratung direkt bei Metav anfordern per eMail info@metav-werkzeuge.com oder Telefon +49 2822 7131930 Produktmerkmale Artikelnummer: 48090-FDA Marke: MetavCUT Serie: Profi Line Bezeichnung: Spiralbohrer Fakten Durchmesser: 9 mm Gesamtlänge: 125 mm Spiralänge: 81 mm Spitzenwinkel: 135° Verpackungseinheit: 5 Besonderheiten Material: HSS-G (Schnellarbeitsstahl, geschliffen) Schaft Ausführung: geschliffen (vollständig geschliffener Zylinderschaft) Norm: DIN 338 (kurze Spiralbohrer mit Zylinderschaft) Typ: Typ N (Normalspirale, geeignet für Metall) Ausführung: kurz (reduzierte Auskraglänge) Farbe: blank (bright finished) Für Bohrmaschine: Handbohrmaschine Hersteller: MetavCUT FAQ Welche Werkstoffe kann ich mit diesem Spiralbohrer bearbeiten? Der MetavCUT Spiralbohrer in HSS-G ist ausgelegt für legierten und unlegierten Stahl, Gussstahl, Gusseisen, Sintereisen, Temperguss, Nichteisenmetalle und Hartkunststoff; für sehr weiche Werkstoffe kann eine andere Bohrersorte sinnvoll sein. Ist dieser Bohrer für Handbohrmaschinen geeignet? Ja, der Zylinderschaft und die kurze Ausführung machen den Spiralbohrer kompatibel mit gängigen Spannfuttern von Handbohrmaschinen sowie stationären Bohrmaschinen. Warum ist die geschliffene Ausführung vorteilhaft? Geschliffene HSS-G-Bohrer bieten hohe Rundlaufgenauigkeit und scharfe Schneiden, was zu saubereren Bohrlöchern führt; der MetavCUT Profi Line nutzt diese Eigenschaft für präzise Metallbearbeitung. Welchen Vorteil bringt der 135° Spitzenwinkel? Der 135° Spitzenwinkel erleichtert das Anbohren harter Werkstoffe und verringert das Wanderverhalten beim Ansetzen, was ein kontrollierteres Einstechen und weniger Ausbrechen bewirkt. Für welche Art von Produktion ist dieser Bohrer nicht ideal? Für sehr tiefe Bohrungen (deutlich über das 5-fache des Durchmessers) oder großserielle Bearbeitung von hochgehärtetem Stahl ist meist ein Vollhartmetallwerkzeug wirtschaftlicher als der HSS-G Spiralbohrer. Welche Normen und Serienbezeichnung hat der Bohrer? Der Bohrer trägt die DIN 338 Klassifikation und gehört zur Profi Line von MetavCUT, Artikelnummer 48090-FDA.
9mm HSS-G Twist Drill DIN 338 ,short, TIN-coated - MetavCUT
Twist Drill — Short HSS-G Drill, 9 mm, 118° point, TIN-coated, DIN 338, fully ground, MetavCUT A short Twist Drill designed for precise metal drilling with Drilling Machines Short design for increased stability and precision TIN-coated surface for reduced wear and friction HSS-G fully ground for faster drilling and clean holes 118° point angle for easy centring in softer metals Conforms to DIN 338 for consistent manufacturing quality Durable HSS-G Construction for Longer Tool Life The HSS-G base material combined with a TIN-coated surface delivers extended lifetime when working with metallic materials. This composition reduces surface wear and friction, so heat buildup is minimised during continuous drilling. The coating supports improved tool life particularly under intermittent cooling, while the substrate material retains cutting edge stability for demanding machining tasks. Short Design and Fully Ground Geometry for Precise Results A shorter overall length reduces overhang and increases stability, which directly improves concentricity and reduces vibration during drilling. The fully ground flute geometry creates sharper cutting edges, enabling up to faster penetration with lower feed forces compared to rolled types. The 118° point angle favours centring and controlled entry in softer metals and certain non-ferrous alloys while still offering reliable starts on slightly curved surfaces. Optimised for Metalworking and Professional Use Designed for use with Drilling Machines, this tool excels in machining alloyed and unalloyed steel, Tempered Cast Iron, Gusseisen, Sintered Iron, Copper, Bronze and hard plastics. Workshops and maintenance professionals benefit from consistent hole quality and reduced rework. The tool’s characteristics make it particularly suitable for precision tasks where minimized runout and reproducible hole tolerances matter. DIN 338 Standard and Practical Handling Advice Manufactured to DIN 338, the tool follows industry definitions for short Twist Drills with Cylindrical Shanks. Being ground rather than rolled results in sharper edges and higher runout accuracy, but also a slightly increased susceptibility to fracture under improper handling. Use appropriate coolant for extended tool life and prefer stationary or well-supported setups to exploit the drill’s precision advantages. Strongly recommend MetavCUT’s short TIN-coated HSS-G Twist Drill for demanding metalworking tasks — for expert advice and application support contact METAV Werkzeuge: 📧 info@metav-werkzeuge.com | ☎️ +49 2822 7131930 | ✔️ WhatsApp +49 170 2837271 — METAV Werkzeuge offers extensive and competent consultation for technical queries and product selection Bezeichnung: Twist Drill Marke: MetavCUT SKU: 28090-FDA Durchmesser: 9 mm Spitzenwinkel: 118° Gesamtlänge: 125 mm Spirallänge: 81 mm Ausführung: short Schaft Ausführung: fully ground Farbe / Beschichtung: TIN-coated Material: HSS-G Norm: DIN 338 Für Bohrmaschine: Drilling Machine Anwendung: Drills for metal Modellserie: Basic Line Hersteller: MetavCUT Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What is the MetavCUT Twist Drill used for? The MetavCUT Twist Drill is mainly applied to the machining of high-strength materials and larger drill diameters; its short design and robust geometry make it suitable for demanding metalworking tasks. The tool’s shape allows relatively easy resharpening and it withstands considerable loads while delivering clean, precise holes. Which three drill types exist? The common classification names three main categories: Metal drills, Wood drills and Masonry/Concrete drills. The MetavCUT Twist Drill belongs to the metal drill group and is optimised for the properties and requirements of metallic materials.
9mm HSS-G Twist Drill DIN 338 ,short, TIN-coated, Type N - MetavCUT
Twist Drill — Short HSS-G Type N, 9 mm, 135°, TiN-coated, DIN 338 The Twist Drill is a short HSS-G metalworking drill bit (Type N) designed for precision drilling in hard materials and optimised for use in drilling machines. Short design for higher stability TiN-coated for extended tool life Fully ground shank for cleaner holes 135° tip for hard metals and stainless steel Conforms to DIN 338 for short drill bits Durable Material and Coating for Long Service Life The short HSS-G construction combined with the TiN-coated surface reduces friction and wear during metalworking, which translates into a significantly longer lifetime under continuous use. With a 9 mm diameter and a flute length of 81 mm, this bit is especially suited for alloyed and unalloyed steel, cast iron, sintered iron, nickel silver, copper, bronze and hard plastics. The TiN layer lowers surface temperature and, when used with appropriate cooling, decreases abrasive wear and maintains cutting performance over prolonged operations. Stable Short Design for Precise, Efficient Drilling Thanks to the reduced overhang of the short execution, this Twist Drill provides superior stability and resists bending under load, enabling more accurate hole positions and improved concentricity. The fully ground geometry yields sharp cutting edges and high running accuracy, allowing up to 40% faster penetration and requiring about 50% less feed force compared with conventional HSS drills. These advantages make it a reliable choice for demanding production and workshop environments where precision and throughput matter. Optimised Tip Geometry and Suitable Applications The 135° point angle is tailored for harder materials and stainless steel: it shortens the initial penetration time and improves centring on tough surfaces. As a Type N normal-spiral bit, the tool excels at general metal drilling tasks and is intended primarily for use with drilling machines. Typical fields of application include maintenance, toolrooms and manufacturing where metals such as steel, cast components and non-ferrous alloys must be drilled with repeatable quality. Compliance, Manufacturing and Best Practice Manufactured according to DIN 338 as a short, cylindrical-shank Spiral Drill, this product is produced as a ground (HSS-G) variant, which implies CNC-ground flutes for sharp edges and precise geometry. Ground drills generally offer cleaner holes and better accuracy than roll-formed types, though they can be somewhat more brittle and therefore are recommended for use with suitable coolant and in predominantly stationary mounting conditions. For optimal results, pair the bit with controlled speeds, adequate coolant and a solid clamping system. For precision metalworking, choose the MetavCUT Twist Drill Type N with TiN coating — for technical advice or to confirm suitability, METAV Werkzeuge provides expert consultation via email info@metav-werkzeuge.com, by phone +49 2822 7131930 or WhatsApp +49 170 2837271 Designation: Twist Drill Brand: MetavCUT SKU: 46090-FDA Diameter: 9 mm Flute Length (Spirallänge): 81 mm Total Length (Gesamtlänge): 125 mm Point Angle (Spitzenwinkel): 135° Type: Type N Execution (Ausführung): short Shank Finish (Schaft-Ausführung): fully ground Coating (Farbe): TiN-coated Material: HSS-G Standard (Norm): DIN 338 Application: Drills for metal / Bohrer für Metall Intended Machine (Für Bohrmaschine): Drilling Machine / Handbohrmaschine Model Series (Modellserie): Standard Line Manufacturer: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What is the Twist Drill (MetavCUT, Type N) mainly used for? The MetavCUT Twist Drill Type N is primarily applied to machining high-strength materials and larger hole diameters; it performs well on alloyed and unalloyed steels and similar metals. Its form allows easier regrinding and it endures considerable loads, making it suitable for demanding metalworking tasks. Which three drill types exist? The main categories are Metal drills (such as the MetavCUT Twist Drill), Wood drills and Masonry/Concrete drills. Each type is optimised in geometry and material for its intended substrate.
9mm HSS-G Twist Drill DIN 338 ,short, TIN-coated, Type N - MetavCUT
Twist Drill Profi Line — 9 mm, 135° · Type N · TIN-coated · Short · HSS‑G · DIN 338 The Twist Drill Profi Line is a short Type N drill designed for precision metalworking with Drilling Machines and Hand Drills. Short design for higher stability and precision TIN-coated HSS‑G for extended tool life Fully ground shank for fast, low-force drilling Optimised 135° tip for hard metals Conforms to DIN 338 for reliable quality Precision and productivity for metalworking Kurz-design drills like the Twist Drill Profi Line combine a reduced overhang with a robust geometry, resulting in higher Stability and less tendency to deflect when drilling. The HSS‑G material paired with a TIN‑coating reduces friction and wear, so holes in alloyed and unalloyed steel, cast components and non‑ferrous metals are produced with consistent accuracy. This yields a measurable time advantage in series work and minimises rework. Less effort, faster penetration with fully ground geometry A fully ground flute and refined cutting geometry ensure the drill requires up to 50% less feed force and can cut faster, especially in demanding materials. The 135° point angle shortens the initial entry time on hard materials such as stainless steel, while the precise tip improves centring. For users, this means easier handling on handheld machines and more predictable results on stationary Drilling Machines. Robust short format tailored to demanding tasks The short overall length (125 mm) and spiral length (81 mm) make this drill particularly suited to operations where rigidity is decisive. The Type N normal helix is the classic choice for metalworking, offering reliable chip evacuation across a broad range of alloys. Operators benefit from cleaner holes and less vibration, which is especially valuable when drilling tougher materials or when hole quality is critical. Practical explanation of key terms The designation HSS‑G indicates a High Speed Steel drill produced by grinding (G = ground), which provides very sharp cutting edges and excellent concentricity. TIN‑coated refers to a thin layer of Titanium Nitride that increases surface hardness and reduces adhesive wear. DIN 338 classifies short twist drills with cylindrical shanks and ensures interchangeability and consistent dimensions across manufacturers. Strong recommendation: For demanding metal drilling choose the MetavCUT Profi Line Twist Drill — for advice or to confirm suitability contact METAV Werkzeuge: 📧 info@metav-werkzeuge.com ☎️ +49 2822 7131930 ✔️ WhatsApp +49 170 2837271 Designation: Twist Drill / Spiralbohrer Marke: MetavCUT SKU: 41090-FDA Diameter: 9 mm Point Angle: 135° Type: Type N Execution: Short Colour/Coating: TIN-coated Material: HSS‑G Shank Execution: Fully ground Spiral Length: 81 mm Overall Length: 125 mm For Drilling Machine: Drilling Machine / Hand Drill suitability indicated Norm: DIN 338 Series: Profi Line Application: Drills for metal Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What is the MetavCUT Profi Line Twist Drill used for? The MetavCUT Profi Line Twist Drill is primarily used for machining high‑strength materials and larger diameters; it is especially effective when drilling alloyed or unalloyed steel and other metals where a short, rigid tool is required. Its construction allows it to withstand higher loads and deliver precise hole geometry. Which three drill types exist? Generally, three common drill categories are distinguished: Metal Drills, Wood Drills and Masonry/Concrete Drills. The MetavCUT Profi Line Twist Drill belongs to the Metal Drill category and is optimised for metalworking tasks. Why are twist drills re‑pointed? Re‑pointing reduces the cross‑cut at the tip of the Twist Drill, significantly lowering friction and therefore the required feed force; at the same time the tip centres better in the workpiece, improving hole accuracy. Can a metal drill be used for wood? A Metal Drill such as the MetavCUT Profi Line can be used in wood, but guidance and hole finish are inferior compared with dedicated wood drills. Metal drills are easier to re‑sharpen and have less self‑pulling action, which can be an advantage in some manual operations. For which drilling depths is the Twist Drill most commonly used? A through‑hole in solid material is typically executed with a Twist Drill. For diameters up to 20 mm and drilling depths up to 100 mm, the Twist Drill is the most frequently used tool, offering efficient chip removal and reliable performance. Is HSS or HSSE better? The common assumption that HSSE alloys are categorically superior to HSS is not always correct. Selection should be based on working conditions: HSSE can offer advantages in specific high‑speed or abrasive situations, but the higher purchase cost must be justified by the application. Are you unsure whether this tool meets your requirements or need additional technical data? METAV Werkzeuge offers comprehensive, expert consultation — contact us by email at info@metav-werkzeuge.com, by phone at +49 2822 7131930 or via WhatsApp at +49 170 2837271.
9mm HSS-G Twist Drill DIN 338 - MetavCUT
Twist Drill — Metal Drill HSS‑G, Ø 9 mm, 135° Point, Spezial, DIN 338, with multi‑bevel cutting edge and triangular shank, MetavCUT The Twist Drill HSS‑G metal drill is designed for fast, precise holes in steel and other hard materials, suitable for hand and stationary drilling machines. Fast drilling: up to 40% quicker than standard HSS Requires 50% less feed force 135° point for harder materials 3‑flat shank for secure grip in cordless drills Conforms to DIN 338 for short twist drills Faster metalworking with less effort This HSS‑G tool delivers a measurable productivity gain thanks to a specially ground geometry that enables up to 40% faster drilling while needing 50% less feed force than conventional HSS drills. The result is reduced operator fatigue and higher throughput in repetitive tasks. For workshops and industrial users who value cycle time, the shortened drilling time translates directly into improved efficiency and lower labour costs per hole without compromising hole quality. Cleaner entry and reliable centring in hard materials The 135° point is optimised for harder workpiece materials such as stainless steel and tempered alloys; it reduces wandering at the start of the hole and shortens the required plunge distance. By decreasing the chisel edge width, the point geometry lowers friction and cutting forces, which helps produce burr‑reduced, clean hole edges. For users unfamiliar with tip angles: a larger point angle typically penetrates harder materials more easily and provides better centring. Secure clamping and compatibility for hand tools The design with a triangular shank (3‑flat shank) ensures slip‑free engagement in chucks of cordless and hand drills, improving torque transfer and reducing slippage during exertion. Conformance to DIN 338 classifies this as a short twist drill with a cylindrical shank made of high‑speed steel, so it fits standard toolholders and is suitable for both mobile and stationary applications. METAV Werkzeuge offers expert consultation if there are questions about drill retention or machine compatibility. Tailored for demanding applications and varied materials Manufactured from HSS‑G, this Rapid‑type drill is suitable for a broad spectrum of materials including alloyed and unalloyed steels, cast and temper‑cast steels, non‑ferrous metals, hard plastics and also for occasional use in wood. Its geometry focuses on reliable performance in metalworking environments; the short configuration is particularly advantageous where rigidity and minimal runout are required. For precision shops, maintenance teams or professionals, this tool combines robustness with straightforward resharpening. Strong recommendation: For professionals seeking faster, cleaner holes in tough materials, choose the MetavCUT HSS‑G Twist Drill — METAV Werkzeuge provides comprehensive technical advice and support via email, phone and WhatsApp: info@metav-werkzeuge.com | +49 2822 7131930 | WhatsApp +49 170 2837271 Designation: Twist Drill Brand: MetavCUT SKU: 55090-FDA Diameter: 9 mm Point angle: 135° Spiral length: 81 mm Total length: 125 mm Shaft execution: with multi‑bevel cutting edge and triangular shank Model series: Spezial Material: HSS‑G Standard: DIN 338 Application: Drill for metal Suitable for: Drilling Machine (hand drill) Packaging unit: 5 Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ For what is a Twist Drill used? The MetavCUT Twist Drill is primarily applied to the machining of high‑strength materials and larger bore diameters; its shape is easy to regrind and it withstands greater loads, making it ideal for demanding metalworking operations. Which three drill types exist? Common drill types are metal drills, wood drills and stone/concrete drills, and the MetavCUT Twist Drill belongs to the metal drill category tailored for metal machining. Why are Twist Drills pointed? Pointing reduces the chisel edge at the tip of the Twist Drill, which significantly lowers friction and therefore requires less feed force; at the same time the point improves centring of the drill in the workpiece. Can a Twist Drill be used to drill wood? A metal drill such as the MetavCUT Twist Drill can be used in wood, but guidance is inferior and the finish is less clean; however these drills are easier to resharpen and show less self‑feed. At which drilling depths is the Twist Drill most used? A full‑bore hole is often executed with a Twist Drill. For diameters up to 20 mm and drilling depths up to 100 mm the Twist Drill is the most commonly used tool. What is better, HSS or HSSE? The general belief that HSSE steels are inherently superior to normal HSS is incorrect; when choosing between HSS and HSSE for a MetavCUT Twist Drill, assess working conditions carefully to determine whether the higher purchase cost of HSSE is justified.
9mm HSS-G Twist Drill DIN 340 ,long, bright finished - MetavCUT
MetavCUT Twist Drill — Twist Drill, 9 mm, 135° tip, Long, Bright finished, HSS‑G, DIN 340 The MetavCUT Twist Drill is a long HSS‑G Twist Drill engineered for deep, precise metal drilling in demanding applications with a 9 mm diameter and a 135° tip. Long HSS‑G Twist Drill for deep holes 9 mm diameter for precise metal drilling 135° tip for hard materials like stainless steel Fully ground shank for high runout accuracy Conforms to DIN 340 for deep hole performance High cutting performance for tough metals Designed to handle challenging materials, this long HSS‑G Twist Drill excels in drilling legierte und unlegierte Stahl grades and cast irons. The larger 135° tip angle reduces entry forces for harder workpieces and improves centring, while the long flute length allows access to recessed holes. Users benefit from faster advance and reduced effort, since the ground geometry promotes a sharper cutting edge and cleaner chip removal. Precise geometry for accurate bores A fully ground shaft and CNC‑ground flutes ensure high runout accuracy and consistently round holes, which is critical when machining components that require tight tolerances. The ground manufacturing method yields very sharp edges and precise tolerance control; however, the harder geometry is best used with appropriate feed, cooling and, for portable setups, cautious handling to avoid brittle breakage. Practical advantages in workshop and production Because the long variant follows DIN 340, it is suited for deeper bores, bushings and situations with limited accessibility. The bright finished surface aids visual inspection and reduces initial friction during entry. For metalworking tasks in small series or repair work the tool reduces rework thanks to cleaner holes, making it an efficient choice where reliability and repeatability matter most. Who benefits and how to use it safely Engineers, toolroom technicians and maintenance professionals profit from the combination of HSS‑G hardness and long design when working on automotive, mechanical and maintenance applications. When using this Twist Drill in stationary machines, apply cutting fluid and moderate speed for best life expectancy. For handheld Drilling Machines, maintain firm guidance and lower advance rates to minimise breakage risk. We recommend the MetavCUT long HSS‑G Twist Drill for demanding deep metal bores — for personalised advice, drill parameter recommendations or further technical data contact METAV Werkzeuge: info@metav-werkzeuge.com, phone +49 2822 7131930 or WhatsApp +49 170 2837271 Designation: Twist Drill Brand: MetavCUT SKU: 53090-FDA Diameter: 9 mm Total length: 175 mm Spiral length: 115 mm Tip angle: 135° Material: HSS‑G Execution: Long Colour: Bright finished Shank execution: Fully ground Standard: DIN 340 For drilling machine: Drilling Machine Application: Drills for metal Model series: Standard Line Packaging unit: 5 Manufacturer: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What is the MetavCUT Twist Drill best used for? The MetavCUT Twist Drill is primarily intended for metalworking and is applied for drilling in high‑strength and cast materials where long, stable bores are required; it is especially suitable for deep holes and hard materials. Can the MetavCUT Twist Drill be re‑sharpened and reused? Yes, the MetavCUT Twist Drill made of HSS‑G can be re‑sharpened by grinding; attention should be paid to preserving the original tip angle and flute geometry to maintain performance. For what are Twist Drills used? The MetavCUT Twist Drill is mainly used when machining high‑strength materials and larger diameters; its form is relatively easy to re‑grind and it stands up to higher loads. Which 3 drill types exist? The main categories are metal drills, wood drills and stone/concrete drills; the MetavCUT Twist Drill belongs to the metal drill type. Why are Twist Drills pointed? The point grind reduces the cross‑cut at the tip of the MetavCUT Twist Drill, lowering friction and required feed forces while improving centring accuracy in the workpiece. Can you drill wood with a Twist Drill? A metal drill such as the MetavCUT Twist Drill can be used in wood, but guidance and finish are inferior compared with dedicated wood drills; metal drills are easier to re‑sharpen and have less self‑feed. At which drilling depths is the Twist Drill most used? Solid drilling for diameters up to around 20 mm and depths up to 100 mm is the most frequent use case; the MetavCUT Twist Drill is a common choice for such through‑holes and deep bores. What is better, HSS or HSSE? Choosing between HSS and HSSE depends on working conditions; the common assumption that HSSE is universally superior is incorrect — evaluate whether the application justifies the higher cost relative to the actual material and speed demands.
9mm Spiralbohrer, 118° Spitzenwinkel, HSS, Morsekegel, rollgewalzt, 87mm Spirallänge - MetavCUT
Profitieren Sie von der Kombination aus HSS-Material und rollgewalzter Fertigung für erhöhte Zähigkeit und verringertes Bruchrisiko bei Standardbohrungen. Nutzen Sie die Morsekegelschaft für sichere Drehmomentübertragung bei Ständerbohrmaschinen. Bestellen Sie den Bohrer direkt über Metav oder fragen Sie unsere Beratung an. Spiralbohrer von MetavCUT — Standard Line (SKU 54090-FDA) Der Spiralbohrer für Metall mit rollgewalzter HSS-Ausführung und Morsekegelschaft bietet belastbare Leistung für Werkstatt und Maschinenpark. HSS rollgewalzt für erhöhte Zähigkeit Morsekegelschaft für sichere Drehmomentübertragung Norm DIN 345 für standardisierte Einsätze 9 mm Durchmesser, 168 mm Gesamtlänge Spitzenwinkel 118° für leichtes Eindringen Haltbarkeit durch Materialwahl und Fertigungsverfahren für robuste Einsätze Die HSS-Legierung in Kombination mit der rollgewalzten Herstellung macht den Bohrer zäher und bruchsicherer als geschliffene Alternativen in vergleichbaren Einsatzbereichen. Diese Fertigungsweise reduziert das Bruchrisiko bei Durchmessern unter 6 mm, bleibt aber auch bei 9 mm robust, wenn es um Bohrungen in legierten und unlegierten Stahl, Guss und Nichteisenmetallen geht. Daraus ergibt sich ein klarer Vorteil in Arbeitsumgebungen, in denen Standzeit und Wirtschaftlichkeit zählen. Sichere Aufnahme und Kraftübertragung für stationäre Maschinen Für den Einsatz in Ständerbohrmaschinen und ähnlichen stationären Maschinen sorgt die Morsekegelschaft für selbsthemmende Verbindung und präzise Drehmomentübertragung. Der Bohrer eignet sich besonders dort, wo hohe Kräfte übertragen werden müssen und ein fixer Sitz in der Aufnahme gefordert ist. Durch die Kombination aus Schaftform und Konstruktion lassen sich Wiederholbohrungen mit stabiler Laufruhe und reduziertem Rundlaufrisiko erreichen. Einsatzbereich und Anwendungsempfehlungen für Metallbearbeitung Der Bohrer ist ausgelegt für allgemeine Metallbohrung bis etwa 900 N/mm² Festigkeit, einschließlich Grauguss, Temperguss und Sintereisen. Beim Bohren in dünnen Blechen empfiehlt sich Vorzentrierung, bei dichten oder zähen Werkstoffen Kühlschmierstoff zu verwenden, um Spananhäufung zu vermeiden. Der Spitzenwinkel 118° erleichtert das Eindringen in weichere Materialien und unterstützt sauberes Ansetzen auf gewölbten Flächen. Präzision und Handling im Arbeitsalltag Mit einer Spirallänge von 87 mm und einer Gesamtlänge von 168 mm bietet der Bohrer guten Spantransport und Reichweite für viele Standardaufgaben. Die DIN 345-Konformität sichert Kompatibilität mit gängigen Normen im Maschinenbau und Instandhaltung. Anwender erhalten damit ein Werkzeug, das bekannte Anforderungen in Werkstatt und Fertigung zuverlässig abdeckt, ohne aufwendige Spezialspannmittel zu benötigen. Setzen Sie auf die MetavCUT Standard Line für belastbare Metallbohrungen und ordern Sie den Spiralbohrer direkt über Metav oder kontaktieren Sie die Fachberatung per eMail unter info@metav-werkzeuge.com bzw. telefonisch Produktmerkmale Artikelnummer: 54090-FDA Marke: MetavCUT Serie: Standard Line Bezeichnung: Spiralbohrer Daten Durchmesser: 9 mm Gesamtlänge: 168 mm Spirallänge: 87 mm Spitzenwinkel: 118° Verpackungseinheit: 1 Besonderheiten Material: HSS Ausführung: rollgewalzt Schaftausführung: Morsekegel — selbsthemmend, hohe Drehmomentübertragung Norm: DIN 345 Farbe: schwarz FAQ Welche Materialien lassen sich mit dem Spiralbohrer bearbeiten? Der MetavCUT Spiralbohrer aus der Standard Line (SKU 54090-FDA) eignet sich für Stahl, legierte und unlegierte Werkstoffe, Guss und Nichteisenmetalle sowie Kunststoffe, solange die Festigkeit 900 N/mm² nicht deutlich überschreitet. Ist die Morsekegelschaft für Ständerbohrmaschinen geeignet? Ja, die Morsekegelschaft des MetavCUT Spiralbohrers bietet eine selbsthemmende Aufnahme, die für Ständerbohrmaschinen und Maschinen mit entsprechender MK-Aufnahme optimale Kraftübertragung ermöglicht. Wie unterstützt die rollgewalzte Fertigung die Einsatzdauer? Die rollgewalzte Herstellung macht den HSS-Bohrer zäher und reduziert das Bruchrisiko insbesondere bei kleineren Durchmessern; die MetavCUT Standard Line profitiert somit von besserer Standzeit bei Standardbohrungen. Welchen Spitzenwinkel hat der Bohrer und warum ist das wichtig? Der Spiralbohrer besitzt einen Spitzenwinkel von 118°, was ein leichteres Eindringen in weichere Materialien und ein verbessertes Ansetzen auf gewölbten Oberflächen ermöglicht.
ACET 150612 KC725M Indexable Insert - Kennametal
Areyou not sure whether this tool fulfils your requirements? Or do you need additional technical data?No problem - we will be happy to help you ✔️ WhatsApp: +49 170 2837271 ☎️ Phone: +49 2822 7131930 📧 eMail: info@metav-werkzeuge.com Product characteristics for ACET 150612 indexable inserts from Kennametal Brand: Kennametal Manufacturer Order Number: ACET150612PPERGC-KC725M-KENNAMETAL Facts / Figures: ISO-Code: ACET150612 Clearance Angle: 7° Angle: 85° Thickness: 6,35mm Radius: 1.2 Features Material: cemented carbide Grade: KC725M with hole Hole Style: cylindrical hole + single-sided countersink (40°–60°) Form: parallelogram Chip Breaker: single-sided Manufacturer: Kennametal; 600 Grant Street, Suite 5100, Pittsburgh, PA 15219, USA; www.kennametal.com; ftmill.service@kennametal.com Brand names and registered trademarks are the property of their respective owners. The mention of protected trademarks and trade names is for illustrative purposes only. Mention of the brands does not imply any relationship to our company. The sales offer includes high-quality, new branded articles from the manufacturer Kennametal. 40START indexable-inserts-ACET-150612-KC725M-Kennametal 40END
ADCA 150350 IC520M Indexable Insert - ISCAR
Not sure whether this tool is suitable for your application? Or are you still missing important technical details? No problem!Contact us - we will be happy to advise you. ✔️ WhatsApp: +49 170 2837271 📧 eMail: info@metav-werkzeuge.com ☎️ Phone: +49 2822 7131930 Design details ADCA 150350 insert from ISCAR Brand: ISCAR Manufacturer Order Number: ADCA150350IC520M Facts & Figures: ISO-Code: ADCA150350 Clearance Angle: 15° Angle: 85° Thickness: 3,18mm Radius: 5 Special features Material: cemented carbide Grade: IC520M with hole Hole Style: cylindrical hole Form: parallelogram Chip Breaker: without Series: ISO MILL/SHRED Manufacturer: ISCAR Ltd.; Industrial Zone, P.O.Box 11; 24959 Tefen; Israel; www.iscar.so.il; info@iscar.co.il Brand names and registered trademarks are the property of their respective owners. The inclusion of registered trademarks and trade names is for illustrative purposes only. There is no connection whatsoever between our company and the brands mentioned. This is a brand new original product of the leading brand ISCAR. 40START indexable-inserts-ADCA-150350-IC520M-ISCAR 40END
ADCR 1505PD IC28 Indexable Insert - ISCAR
Are you unsure whether the tool is suitable for your application? Or do you need further technical information?No problem - feel free to contact us! ✔️ WhatsApp: +49 170 2837271 📧 eMail: info@metav-werkzeuge.com ☎️ Phone: +49 2822 7131930 Product characteristics for indexable inserts ADCR 1505PD from ISCAR Brand: ISCAR Manufacturer Order Number: ADCR1505PDFR-PIC28 Series: HELIMILL/HELI2000 ISO-Code: ADCR1505PD Grade: IC28 Material: cemented carbide Form: parallelogram Clearance Angle: 15° without hole Thickness: 5,56mm Chip Breaker: single-sided Angle: 85° Manufacturer: ISCAR Ltd.; Industrial Zone, P.O.Box 11; 24959 Tefen; Israel; www.iscar.so.il; info@iscar.co.il Registered brand names and trademarks are the property of their respective owners. The mention of brands and registered trademarks is for descriptive purposes only. There is no connection whatsoever between our company and the brands mentioned. The sales offer includes high-quality, new branded articles from the manufacturer ISCAR. 40START indexable-inserts-ADCR-1505PD-IC28-ISCAR 40END
ADCR 1505PD IC928 Indexable Insert - ISCAR
Not sure whether this tool is suitable for your application? Or are you still missing important technical details? No problem!Contact us - we will be happy to advise you. 📧 eMail: info@metav-werkzeuge.com ☎️ Phone: +49 2822 7131930 ✔️ WhatsApp: +49 170 2837271 Product details ADCR 1505PD indexable inserts from ISCAR Brand: ISCAR Manufacturer Order Number: ADCR1505PDFRIC928 Figures for the tool: ISO-Code: ADCR1505PD Clearance Angle: 15° Angle: 85° Thickness: 5,56mm Special features Material: cemented carbide Grade: IC928 without hole Form: parallelogram Chip Breaker: single-sided Series: HELIMILL/HELI2000 Manufacturer: ISCAR Ltd.; Industrial Zone, P.O.Box 11; 24959 Tefen; Israel; www.iscar.so.il; info@iscar.co.il Registered trademarks and trade names are the property of their respective owners. The indication of brand names and trademarks is for information purposes only. Named brands are in no way associated or co-operate with our company. The article presented is a brand-new original product of the ISCAR brand. 40START indexable-inserts-ADCR-1505PD-IC928-ISCAR 40END
ADCT 1505PD IC28 Indexable Insert - ISCAR
Are you unsure whether the tool is suitable for your application? Or do you need further technical information?No problem - feel free to contact us! ✔️ WhatsApp: +49 170 2837271, 📧 eMail: info@metav-werkzeuge.com, ☎️ Phone: +49 2822 7131930 Product characteristics indexable inserts ADCT 1505PD from ISCAR Brand: ISCAR Manufacturer Order Number: ADCT1505PDFR-HMIC28 Facts / Figures: ISO-Code: ADCT1505PD Clearance Angle: 15° Angle: 85° Thickness: 5,56mm Features Material: cemented carbide Grade: IC28 with hole Hole Style: cylindrical hole + single-sided countersink (40°–60°) Form: parallelogram Chip Breaker: single-sided Series: HELIMILL/HELI2000 Manufacturer: ISCAR Ltd.; Industrial Zone, P.O.Box 11; 24959 Tefen; Israel; www.iscar.so.il; info@iscar.co.il Ownership of brand names and protected trademarks remains with their owners. The mention of protected brand names and trademarks is for illustrative purposes only. Our company has no commercial, legal or other connection with the brands concerned. This is a brand new original product of the leading brand ISCAR. 40START indexable-inserts-ADCT-1505PD-IC28-ISCAR 40END
ADCT 1505PD IC328 Indexable Insert - ISCAR
Not sure whether this tool is suitable for your application? Or are you still missing important technical details? No problem!Contact us - we will be happy to advise you. 📧 eMail: info@metav-werkzeuge.com ☎️ Phone: +49 2822 7131930 ✔️ WhatsApp: +49 170 2837271 Product characteristics for ADCT 1505PD indexable inserts from ISCAR Brand: ISCAR Manufacturer Order Number: ADCT1505PDFR-HMIC328 Dataand Figures: ISO-Code: ADCT1505PD Clearance Angle: 15° Angle: 85° Thickness: 5,56mm Special features Material: cemented carbide Grade: IC328 with hole Hole Style: cylindrical hole + single-sided countersink (40°–60°) Form: parallelogram Chip Breaker: single-sided Series: HELIMILL/HELI2000 Manufacturer: ISCAR Ltd.; Industrial Zone, P.O.Box 11; 24959 Tefen; Israel; www.iscar.so.il; info@iscar.co.il Brand names and registered trademarks are the property of their respective owners. The use of brand names and trademarks is for descriptive purposes only. The brands mentioned are not in any contractual relationship with our company. The items offered are original, brand-new goods of the ISCAR brand. 40START indexable-inserts-ADCT-1505PD-IC328-ISCAR 40END
ADCT 1505PD IC928 Indexable Insert - ISCAR
Unsure whether the tool is the right one? Or are you missing technical data?Just get in touch with us! 📧 eMail: info@metav-werkzeuge.com ☎️ Phone: +49 2822 7131930 ✔️ WhatsApp: +49 170 2837271 Design details indexable inserts ADCT 1505PD from ISCAR Brand: ISCAR Manufacturer Order Number: ADCT1505PDFR-HMIC928 Data/ Figures: ISO-Code: ADCT1505PD Clearance Angle: 15° Angle: 85° Thickness: 5,56mm Features Material: cemented carbide Grade: IC928 with hole Hole Style: cylindrical hole + single-sided countersink (40°–60°) Form: parallelogram Chip Breaker: single-sided Series: HELIMILL/HELI2000 Manufacturer: ISCAR Ltd.; Industrial Zone, P.O.Box 11; 24959 Tefen; Israel; www.iscar.so.il; info@iscar.co.il The rights to brand names and registered trademarks are held by their rightful owners. The designation of brand names and trademarks is for explanatory purposes only. Our company has no commercial, legal or other connection with the brands concerned. The items offered are original, brand-new goods of the ISCAR brand. 40START indexable-inserts-ADCT-1505PD-IC928-ISCAR 40END
ADCT 154512 KCSM40 Indexable Insert - Kennametal
Not sure whether this tool is suitable for your application? Or are you still missing important technical details? No problem!Contact us - we will be happy to advise you. 📧 eMail: info@metav-werkzeuge.com, ☎️ Phone: +49 2822 7131930, ✔️ WhatsApp: +49 170 2837271 Technical data indexable inserts ADCT 154512 from Kennametal Brand: Kennametal Manufacturer Order Number: ADCT154512PDSRLD-KCSM40-KENNAMETAL Facts / Figures: ISO-Code: ADCT154512 Clearance Angle: 15° Angle: 85° Radius: 1.2 Special features Material: cemented carbide Grade: KCSM40 with hole Hole Style: cylindrical hole + single-sided countersink (40°–60°) Form: parallelogram Chip Breaker: single-sided Manufacturer: Kennametal; 600 Grant Street, Suite 5100, Pittsburgh, PA 15219, USA; www.kennametal.com; ftmill.service@kennametal.com Brand names and registered trademarks are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. Named brands are in no way associated or co-operate with our company. This is a brand new original product of the leading brand Kennametal. 40START indexable-inserts-ADCT-154512-KCSM40-Kennametal 40END
ADCT 154512 KCSM40 Indexable Insert - Kennametal
Areyou not sure whether this tool fulfils your requirements? Or do you need additional technical data?No problem - we will be happy to help you ✔️ WhatsApp: +49 170 2837271 📧 eMail: info@metav-werkzeuge.com ☎️ Phone: +49 2822 7131930 Performance features inserts ADCT 154512 from Kennametal Brand: Kennametal Manufacturer Order Number: ADCT154512PDERLD-KCSM40-KENNAMETAL Figures for the tool: ISO-Code: ADCT154512 Clearance Angle: 15° Angle: 85° Radius: 1.2 Special features Material: cemented carbide Grade: KCSM40 with hole Hole Style: cylindrical hole + single-sided countersink (40°–60°) Form: parallelogram Chip Breaker: single-sided Manufacturer: Kennametal; 600 Grant Street, Suite 5100, Pittsburgh, PA 15219, USA; www.kennametal.com; ftmill.service@kennametal.com Ownership of brand names and protected trademarks remains with their owners. The mention of brands and registered trademarks is for descriptive purposes only. Mention of the brands does not imply any relationship to our company. This is a brand new original product of the leading brand Kennametal. 40START indexable-inserts-ADCT-154512-KCSM40-Kennametal 40END
ADCT 154532 KC725M Indexable Insert - Kennametal
Are you unsure whether the tool is suitable for your application? Or do you need further technical information?No problem - feel free to contact us! 📧 eMail: info@metav-werkzeuge.com, ☎️ Phone: +49 2822 7131930, ✔️ WhatsApp: +49 170 2837271 Product specifications for ADCT 154532 indexable inserts from Kennametal Brand: Kennametal Manufacturer Order Number: ADCT154532PDSRLD-KC725M-KENNAMETAL Data/ Figures: ISO-Code: ADCT154532 Clearance Angle: 15° Angle: 85° Radius: 3.2 Features Material: cemented carbide Grade: KC725M with hole Hole Style: cylindrical hole + single-sided countersink (40°–60°) Form: parallelogram Chip Breaker: single-sided Manufacturer: Kennametal; 600 Grant Street, Suite 5100, Pittsburgh, PA 15219, USA; www.kennametal.com; ftmill.service@kennametal.com Registered trademarks and trade names are the property of their respective owners. Quotations of brand names and registered trademarks are for illustrative purposes only. The brands mentioned are not in any contractual relationship with our company. This is a brand new original product of the leading brand Kennametal. 40START indexable-inserts-ADCT-154532-KC725M-Kennametal 40END
Why carbide indexable inserts remain the go-to choice
Carbide indexable inserts are the most widely used and versatile cutting inserts in machining. Manufactured from a sintered mixture of hard particles such as tungsten carbide and a metallic binder like cobalt, these inserts form the actual cutting edge on toolholders including milling cutters, turning inserts and drills. Synonyms used here: carbide cutting inserts, indexable carbide inserts.
How they perform under coolant and load
As the cutting element, carbide indexable inserts enable economic and precise machining across a broad spectrum of materials, from soft non‑ferrous metals to high‑strength steels. In tool systems without internal cooling, heat generated at the cutting zone is normally removed by external machine nozzles using coolant, which is adequate for most standard tasks, open contours and easily accessible components. For deep holes, heavy roughing or when working with materials that generate high temperatures such as stainless steel or titanium alloys, the use of internal cooling is essential: coolant is delivered through internal channels in the toolholder directly to the cutting edge under pressure to prevent thermal overload, optimise chip formation and extend insert life.
Key performance gains you can expect
- increased tool life through the high wear resistance and balanced toughness of tungsten carbide inserts
- consistent chip control and surface finish when coolant is delivered precisely via internal channels
- reduced machine downtime thanks to easy indexability and fast insert changes on compatible toolholders
- broad material compatibility, from soft non‑ferrous metals to hardened steels, enabling fewer tool variants in stock
- economic productivity by combining long stand life with repeatable cutting performance
Metav as your precision partner
Metav stands for the democratisation of precision. With decades of expertise and a catalogue that spans from high‑precision measuring instruments to full workshop equipment, Metav acts as a reliable quality filter for the European market from its Emmerich location. Over 48,000 customers trust Metav’s range and service; the breadth of more than 250,000 products helps reduce supplier complexity while ensuring consistent supply and product quality for industry and trade.
In brief: carbide indexable inserts at a glance
Carbide indexable inserts deliver the necessary balance of extreme wear resistance and mechanical toughness for versatile, cost‑efficient machining. Used with appropriate coolant strategy—external coolant for general work and internal cooling for demanding, deep or heat‑intensive operations—they are a cornerstone of modern metalcutting.
FAQ
What are carbide indexable inserts made of?
Carbide indexable inserts are manufactured from a sintered mixture of hard particles such as tungsten carbide and a metallic binder like cobalt, producing a cutting material that combines high wear resistance with the toughness needed to resist mechanical shock.
When is internal cooling necessary for carbide cutting inserts?
Internal cooling becomes necessary for deep hole drilling, heavy roughing and when machining materials that generate significant heat, such as stainless steel or titanium alloys. Internal cooling channels in the toolholder deliver coolant directly to the cutting edge to prevent thermal overload and improve chip breakage.
Can indexable carbide inserts be used without internal cooling?
Yes. For most standard applications, open contours and well‑accessible components, external coolant supplied by machine nozzles is sufficient, as tungsten carbide is more tolerant of moderate temperature fluctuations than some alternative materials.
How do carbide indexable inserts contribute to production efficiency?
By offering long tool life, stable cutting performance and quick indexability on compatible toolholders, indexable carbide inserts help reduce downtime, simplify tool inventories and maintain consistent part quality across varying materials.
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com