DCMT 11T304 KC850 Indexable Insert - Kennametal

Take advantage of a compact, secure clamping solution that combines left-hand cutting capability with internal coolant to extend insert life and improve surface finish; its 12 x 12 mm tool head and 110 mm overall length permit tight setups and stable machining. Order or request technical advice directly via Metav Werkzeuge for quick delivery and integration planning. SDJCL 1212 clamp holder (SDJC for DCMT indexable inserts) — left-hand, internal coolant — Teknik Makina A SDJCL 1212 clamp holder designed for left-hand turning with DCMT 11T3 indexable inserts, offering internal coolant and a compact 12 x 12 mm head for reliable part machining in confined fixtures Left-hand cutting orientation Internal coolant supply 12 x 12 mm tool head 110 mm overall length Stable left-hand turning with consistent chip control The compact clamping geometry and left-hand cutting configuration deliver repeatable results in turning applications where reverse orientation is required. Fitted for DCMT 11T3 indexable inserts, the holder is engineered to keep the insert at the correct cutting angle (93°) and cutting height, ensuring predictable chip formation and surface quality. The robust design translates into fewer interruptions for insert changes and a steadier throughput in batch production. Coolant-fed performance and space-saving dimensions Internal coolant routing supports concentrated lubrication and chip evacuation directly at the cutting edge, which helps to reduce thermal load and improve insert life. With a compact 12 x 12 mm head and an overall length of 110 mm, the holder suits close-clearance tools and face-turned components where tool overhang must be minimised. The low mass (0.11 kg) and precise geometry aid vibration damping, supporting finer surface finishes and tighter tolerances on production parts. Practical fitment and service-friendly details Designed for straightforward assembly, the holder accepts the TA030 U-plate and is secured using an M5 plate screw and a Torx clamping screw (M3.5x8.5) tightened with a T15 key. The ISO designation SDJCL 1212 and bar reference J11-F-IC make specification and reordering clear in procurement documentation. Internal coolant and standardised fixings reduce setup time and match common workshop practices, enabling rapid swap-out and minimal adjustments between jobs. For integration support or to secure supply of the Teknik Cutting Tools SDJCL 1212 clamp holder with internal coolant, contact Metav Werkzeuge in Emmerich for technical advice and reliable delivery via info@metav-werkzeuge.com or +49 2822 7131930 Technical Data SKU: AP575TM ISO designation: SDJCL 1212 Model: SDJC for DCMT indexable inserts Manufacturer: Teknik Makina Cutting direction: left Suitable inserts: DCMT 11T3 Internal coolant: yes Facts Tool head width: 12 mm Tool head height: 12 mm Cutting head width: 12 mm Overall length: 110 mm Cutting height: 32 mm Weight: 0.11 kg Cutting angle: 93° Screw sizes: M5, M3.5x8.5 Torx key: T15 Special features Internal coolant supply For DCMT 11T3 indexable inserts Left-hand cutting orientation ISO designation SDJCL 1212 Bar designation J11-F-IC Compatible with TA030 U-plate FAQ Which indexable inserts suit this holder? The holder is specified for DCMT 11T3 indexable inserts; the SDJCL 1212 geometry ensures correct seating and reliable cutting performance with those inserts. Does the holder provide internal coolant? Yes — the SDJCL 1212 clamp holder features internal coolant routing to the insert zone for improved cooling and chip control. What is the overall length and head size? Overall length is 110 mm with a compact tool head of 12 x 12 mm, providing a small footprint for confined machining. Which screws and keys are required for assembly? Assembly uses an M5 plate screw and a Torx clamping screw M3.5x8.5, tightened with a T15 Torx key as supplied in typical workshop toolkits. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a compact, ISO‑rated clamping solution that combines precise insert seating and internal coolant for improved chip control; its 16×16 mm cross section and 100 mm length deliver consistent rigidity in short overhang setups. Order through Metav Werkzeuge or consult our specialists for integration advice and fast supply from Emmerich. Klemmhalter — SDJC toolholder for DCMT 11T3 inserts, internal coolant, right‑hand (Teknik Cutting Tools) The Klemmhalter is a right‑hand SDJC toolholder designed for turning with DCMT 11T3 indexable inserts; suited to workshop and light industrial lathes where secure clamping and coolant delivery improve cycle stability. SDJCR 1616 profile, 16×16 mm Compatible with DCMT 11T3 inserts Internal coolant supply for chip control Right‑hand holder with 100 mm overall length Precision seating and reproducible cutting performance The SDJC design provides a clear datum for insert location and repeatable clamping, which reduces setup time and minimises positional deviation during batch work. The holder accepts DCMT 11T3 indexable inserts and secures them with a M3.5x8.5 Torx clamping screw using a T15 key, ensuring a firm and serviceable connection. These characteristics translate into stable tool life and consistent workpiece geometry when exchanging inserts or performing rapid tool changes. Improved process reliability through internal coolant Built‑in internal coolant channels deliver cutting fluid directly to the cutting edge, supporting effective chip evacuation and thermal control in interrupted or continuous cuts. The focused coolant flow helps preserve edge integrity on the insert and reduces built‑up edge formation, which in turn maintains surface finish and prolongs insert life. For operations where coolant‑assisted cutting is required, the integrated supply contributes to fewer reworks and higher first‑pass yield. Compact geometry for rigid turning and short overhangs With a cross section of 16×16 mm and a cutting height of 32 mm, the holder offers a compact footprint and predictable stiffness for near‑centreline applications. The specified cutting angle 93° and right‑hand orientation support conventional turning directions while the 100 mm overall length limits overhang to improve vibration resistance. The unit’s modest mass (approx. 0.17 kg) facilitates rapid toolchanging without compromising stability on smaller toolposts. Simple integration and low‑effort maintenance Designed to common mounting practices, the holder is identified as SDJCR 1616, compatible with standard boring bar designations such as H11‑F‑IC, and requires only a T15 Torx key for clamping or maintenance. The accessible screw and predictable seating make insert indexing and routine checks straightforward, which reduces downtime between shifts. This combination of standard interfaces and robust construction supports efficient workshop workflows and predictable shopfloor uptime. For tailored procurement of Teknik Cutting Tools' SDJC clamping holders (AP572TM) and to discuss fitment with existing toolposts, contact Metav Werkzeuge in Emmerich by email at info@metav-werkzeuge.com or by phone on +49 2822 7131930 for expert advice and supply options Technical Data Article number: AP572TM ISO designation: SDJCR 1616 Product designation: SDJC for DCMT indexable inserts Manufacturer: Teknik Makina Facts Width: 16 mm Height: 16 mm Cutting head width: 16 mm Cutting height: 32 mm Overall length: 100 mm Overall height: 16 mm Weight: 0.17 kg Cutting angle: 93° Cutting direction: Right Special features Compatible with DCMT 11T3 inserts Internal coolant supply SDJC clamping geometry Torx clamping screw M3.5x8.5 Torx key size T15 Compatible with H11‑F‑IC boring bars Right‑hand orientation FAQ What insert type fits this holder? The holder is designed for DCMT 11T3 indexable inserts and locates them on the SDJC seat for secure clamping and repeatable positioning. Does the toolholder provide coolant to the insert? Yes, the toolholder features internal coolant channels to deliver cutting fluid directly toward the cutting edge, improving chip evacuation and tool life. What are the key mounting dimensions to check before ordering? Verify the 16×16 mm cross section and 100 mm overall length to ensure compatibility with the toolpost and necessary overhang for the intended operation. Which clamping hardware is used for insert retention? Insert retention uses a M3.5x8.5 Torx screw tightened with a T15 key for quick service and reliable clamping. Is this holder right‑hand or left‑hand? This version is right‑hand, with a cutting angle of 93°, optimised for conventional right‑hand turning directions. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a compact, coolant-ready toolholder that secures DCMT 11T3 inserts reliably while delivering stable right-hand turning performance; order the AP571TM directly via Metav Werkzeuge or consult our specialists for application advice. Clamping holder AP571TM — SDJC toolholder for DCMT 11T3 with internal coolant The Clamping holder AP571TM is a right-hand SDJC toolholder designed for use with DCMT 11T3 indexable inserts, offering internal coolant supply and a compact 12 × 12 mm cutting head for stable precision turning. SDJCR 1212 ISO designation Compatible with DCMT 11T3 inserts Internal coolant for improved chip evacuation Robust 12 x 12 mm cutting head dimensions Secure clamping that keeps cutting geometry stable The AP571TM is engineered to maintain consistent cutting geometry during interrupted cuts and heavy finishing passes. The SDJCR 1212 designation corresponds to a proven clamping form that fits standard turning toolholders, while the M3.5x8.5 Torx screw and T15 key provide a secure, repeatable clamp force. This mechanical reliability minimises insert movement and run-out, translating into predictable tool life and a constant surface finish. For workshops aiming to reduce rework and tool-change downtime, this holder supports efficient shopfloor processes through dependable retention and straightforward maintenance. Coolant-fed design for better chip control and tool life Integrated supply channels allow coolant to reach the cutting zone directly, supporting effective chip control and heat dissipation. The internal coolant capability reduces edge temperature and helps prevent built-up edge on the insert, which in turn extends insert life and preserves component tolerances. In applications where surface finish and tool longevity affect production economics, this coolant-ready configuration offers a measurable improvement in machining stability and process reproducibility, especially on medium–heavy duty turning where thermal management matters. Compact dimensions for rigid performance in confined setups With a cutting-head footprint of 12 mm by 12 mm, a cutting height of 32 mm and an overall length of 110 mm, the holder combines rigidity with access to tighter fixtures. The modest mass (0.11 kg) and a 93° cutting angle produce low overhang and reduced vibration, improving chip formation and dimensional control. The right-hand cutting direction specification makes the holder suitable for standard right-hand lathes and CNC turning centres. These compact geometries are particularly beneficial for secondary operations and when tool clearance is limited, enabling more reliable finishes without sacrificing stability. Easy integration and standardised tooling for efficient workflows The toolholder accepts common DCMT 11T3 indexable inserts and mounts on a J11-F-IC shank, simplifying inventory management across tooling systems. The ISO-style designation and conventional fixing hardware mean familiar handling for technicians and fast replacement during tool changes. Standardisation reduces the number of specialised parts required in a busy workshop and streamlines procurement, maintenance and operator training — factors that support continuous, predictable production rhythms. For coolant-ready, compact turning solutions from Teknik Makina, contact Metav Werkzeuge in Emmerich for procurement and technical advice via info@metav-werkzeuge.com or call +49 2822 7131930 Technical Data Article number: AP571TM Manufacturer: Teknik Makina Article designation: SDJC for DCMT indexable inserts (SDJCR 1212) Facts Cutting-head width: 12 mm Holder height: 12 mm Cutting-head width (alternate): 12 mm Cutting height: 32 mm Overall length: 110 mm Overall height: 12 mm Weight: 0.11 kg Cutting angle: 93° Cutting direction: right-hand Torx screw: M3.5x8.5 Torx key: T15 Shank designation: J11-F-IC Special features Internal coolant: yes Compatible inserts: DCMT 11T3 ISO designation: SDJCR 1212 FAQ What insert type fits this holder? The holder accepts DCMT 11T3 indexable inserts; the AP571TM is specified for this insert form and secures it using the SDJCR-style clamp. Is the holder suitable for coolant-fed machining? Yes. The AP571TM features internal coolant channels to deliver cutting fluid to the insert interface for improved chip evacuation and thermal control. Which cutting direction is supported? This toolholder is configured for right-hand cutting operations and is intended for installation on right-handed turning setups. What are the key mounting and fixing details? Fixing is provided via an M3.5x8.5 Torx screw tightened with a T15 key; shank designation for mounting is J11-F-IC. How does the compact design affect performance? The 12 × 12 mm cutting-head dimensions and 110 mm overall length reduce overhang, increase rigidity and help to lower vibration, resulting in more consistent finishes and longer tool life. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a compact, left‑hand clamping solution with internal coolant and proven compatibility with DCMT 11T3 indexable inserts for steady turning performance; purchase directly from Metav Werkzeuge or request specialist advice from our consultants. SDJC Clamping Holder for DCMT Indexable Inserts — Left‑hand holder with internal coolant (Teknik Makina) The SDJC for DCMT Indexable Inserts is a left‑hand clamping holder designed for turning operations that require internal coolant delivery and a compact 12 mm shank for versatile workshop use Holder SDJCL 1212 by Teknik Makina Internal coolant for reliable chip evacuation Compatible with DCMT 11T3 indexable inserts Left‑hand orientation, 93° cutting angle Precision clamping for reproducible turning results The holder is engineered to deliver consistent clamping pressure via its SDJCL 1212 ISO profile, which secures DCMT‑style inserts with repeatable seating. This reduces setup time and minimises rework by keeping the insert position stable across cycles. The compact 12 mm shank and 16 mm cutting head width balance rigidity and access, so turning tasks that demand tight tolerances benefit from reduced vibration and improved surface finish. Coolant‑assisted chip control that supports productivity Equipped with internal coolant, the tool directs coolant to the cutting zone so chips are cleared efficiently and tool life is extended. For materials that produce long or stringy chips, forced coolant can prevent martensitic heat build‑up and lessen manual cleaning intervals. The internal feed is integrated without compromising the holder profile, meaning coolant is supplied while retaining full clamping reliability. Designed for workshop compatibility and quick changeovers Compatibility with DCMT 11T3 indexable inserts and the J11‑IC toolholder designation ensures that the holder fits common insert geometries and available insert grades. The left‑hand orientation and 93° cutting angle are suited to specific turning set‑ups, while the supplied Torx and clamping hardware (M3.5x11 Torx screw, T15 key, and M5 clamping plate screw) are industry standard for rapid, secure insert changes. At 110 mm overall length and 0.11 kg weight, the holder is easy to handle during tool changes and storage. Built for reliable, everyday workshop use Materials and construction are focused on longevity and consistent performance; the holder is finished to withstand routine use and is compatible with a range of insert grades for diverse materials. The robust clamping mechanism, together with measured dimensions and a 32 mm cutting height, supports repeatable setups and predictable machining results, so production planners can schedule operations with confidence rather than frequent adjustments. For reliable turning with internal coolant and DCMT compatibility, contact Metav Werkzeuge for availability and technical guidance — call +49 2822 7131930 or email info@metav-werkzeuge.com Technical data Article number: AP514TM Manufacturer: Teknik Makina ISO designation: SDJCL 1212 For indexable inserts: DCMT 11T3 Toolholder designation: J11-IC Weight: 0.11 kg Overall length: 110 mm Total height: 12 mm Shank width: 12 mm Cutting head width: 16 mm Cutting height: 32 mm Cutting angle: 93° Internal coolant: yes Cutting direction: left U‑plate: TA030 U‑plate screw: M5 Torx screw: M3,5x11 Torx key: T15 SKU: AP514TM FAQ What insert types are compatible with this holder? The holder accepts DCMT 11T3 indexable inserts; the SDJC geometry is matched to that insert form for reliable seating and repeatability. Is the coolant internal or external on this clamping holder? Internal coolant is provided; coolant is channelled to the cutting zone to aid chip evacuation and tool life. What is the ISO designation and main dimensions of the holder? The ISO designation is SDJCL 1212, with a 12 mm shank width, 110 mm overall length and a 16 mm cutting head width. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a compact, work-ready toolholder that combines precise insert compatibility and internal coolant for stable turning results; its robust clamping with standard fasteners keeps downtime to a minimum. Order the holder directly via Metav Werkzeuge or consult our specialists for application-specific advice. Klemmhalter — SDJC tool holder for DCMT indexable inserts with internal coolant, right-hand The Klemmhalter is a right-hand SDJC tool holder engineered for DCMT 11T3 indexable inserts, optimised for external turning operations where coolant supply and repeatable clamping are essential. Internal coolant supply For DCMT 11T3 indexable inserts Right-hand turning orientation Compact 110 mm overall length Precise compatibility that reduces set-up time The holder is specified as SDJCR 1212, created to accept DCMT 11T3 indexable inserts and to work with standard tool shanks such as J11-IC. Its defined geometry and the near-right cutting angle 93° ensure predictable tool projection and chip flow during external turning. Designed for direct replacement of like-form holders, this component minimises the need for re-profiling toolpaths, supporting efficient machine changeover and stable process control. Robust mechanical design for reliable clamping Key fastening elements are supplied in common workshop standards: a clamp plate screw M5, a securing Torx screw M3.5x11 and the matching Torx T15 key interface are used for the insert seat and assembly. The holder presents a compact footprint — 110 mm overall length with a total height 12 mm, a toolholder width of 12 mm and a cutting-head width of 16 mm — keeping overhang low and reducing vibration. The assembly weight of 0.11 kg contributes to improved dynamic behaviour on high-speed lathes. Integrated coolant and maintenance advantages Internal coolant is built into the toolholder to deliver cutting fluid directly to the insert edge, improving chip evacuation, extending insert life and stabilising cutting temperatures. The use of internal feed reduces reliance on external nozzles and simplifies set-up. Routine service focuses on fastener checks and ensuring the TA030 clamp plate is seated correctly; familiar fasteners and commonly available keys make maintenance quick and predictable, reducing unplanned downtime. Application scenarios and mounting guidance This right-hand tool holder is intended for external turning where DCMT 11T3 inserts provide the required cutting geometry and edge preparation. Typical applications include finishing and light to medium machining of steels where predictable chip control and coolant delivery matter. The nominal cutting height 32 mm must be considered when calibrating tool offsets and selecting insert grades. Mounting into compatible tool posts or boring bars follows standard procedures for the J11-IC shank family; the compact design supports tight toolpacks and multi-station turrets. For tailored technical guidance or to secure supply of the Teknik Makina SDJCR 1212 clamping toolholder, contact Metav Werkzeuge for expert advice and prompt delivery from Emmerich. Technical data Article number: AP509TM Manufacturer: Teknik Makina ISO designation: SDJCR 1212 Weight: 0.11 kg Compatible insert: DCMT 11T3 Core data Overall length: 110 mm Total height: 12 mm Holder width: 12 mm Cutting-head width: 16 mm Cutting height: 32 mm Cutting angle: 93° Direction: Right-hand Special features Internal coolant Clamp plate type: TA030 Clamp plate screw: M5 Securing screw: Torx M3.5x11 Torx key size: T15 Compatible shank designation: J11-IC FAQ Is this holder compatible with DCMT 11T3 inserts? Yes, the holder is designed specifically for DCMT 11T3 indexable inserts and seats them in the SDJC pocket geometry for secure cutting. Does the tool holder supply internal coolant to the insert? Internal coolant is integrated into the tool holder to deliver fluid directly to the cutting edge, improving chip control and insert life. Which fasteners are used to secure the insert and clamp plate? The design uses a M5 clamp plate screw and a Torx M3.5x11 securing screw; assembly and service use a Torx T15 key. What is the cutting orientation and how does it affect mounting? This is a right-hand turning holder; it must be mounted accordingly in the turret or tool post to achieve the specified cutting direction. Can this holder be mounted on standard J11-IC shanks? Yes, the holder is compatible with tool shanks designated J11-IC, facilitating integration into existing tool set-ups. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of robust clamping, internal coolant and a compact 25 × 25 mm shank for secure left‑hand turning in medium‑duty CNC operations; order directly via Metav Werkzeuge or consult our specialists for application advice. SDJCL 2525 clamping toolholder — SDJC for DCMT indexable inserts, left‑hand, internal coolant — Teknik Makina The SDJCL 2525 is a left‑hand turning toolholder designed for DCMT 11T3 indexable inserts, engineered to provide stable clamping and targeted coolant delivery for improved insert life in metalcutting operations. Left‑hand orientation for turning operations Internal coolant channel for improved cooling Compatible with DCMT 11T3 indexable inserts 25 × 25 mm shank, 150 mm overall length Consistent clamping for repeatable turning accuracy The holder is built around a compact 25 × 25 mm shank and a defined 93° cutting angle, providing a stable interface for turning tasks where repeatability matters. The clamping geometry secures DCMT style inserts and reduces micro‑movement at the cutting edge, which translates into consistent surface finish and predictable tool life. With a 32 mm cutting head width and a 35 mm cutting height, the component is suitable for routine external turning and facing tasks on conventional and CNC lathes. The robust design and measured mass (approx. 0.735 kg) help dampen vibration for smoother cuts. Targeted cooling and improved insert longevity This toolholder features an internal coolant passage that directs cutting fluid toward the insert seat and cutting zone, helping to reduce thermal load and minimise built‑up edge. Direct coolant improves chip control and often extends the service intervals for carbide inserts, which makes the solution economically attractive when productivity and uptime are priorities. The combination of internal coolant and the SDJC clamping concept supports reliable cutting performance, especially in interrupted cuts and heavy‑duty passes with DCMT 11T3 inserts. Straightforward installation and workshop compatibility Designed to ISO style SDJCL 2525 dimensions, the toolholder integrates smoothly into standard toolposts and turret systems. Fixing is managed with a Torx T15 drive and M3.5×11 Torx screw for secure insert retention; the holder accepts M11 mounting on compatible boring bars and pairs with the TA030 clamping plate where required. The overall 150 mm length keeps reach compact while enabling access to typical workpiece geometries. The straightforward mounting and standardised interfaces make this holder a practical choice for workshops and subcontractors aiming to rationalise their tooling setup. Purpose and ideal applications Engineered for left‑hand external turning with DCMT 11T3 inserts, this holder is most useful in small to medium‑batch production where stability and predictable tool life are required. It suits steel and alloy turning in industrial and precision workshops, and is a reliable option for lathe operations that benefit from directed coolant and a compact, rigid shank. The straightforward mechanical concept reduces setup time and supports reproducible process parameters during component runs. For procurement or technical advice on the SDJCL 2525 clamping toolholder from Teknik Makina, contact Metav Werkzeuge for tailored recommendations and delivery from our Emmerich distribution centre; email info@metav-werkzeuge.com or call +49 2822 7131930 Technical Data Article number: AP517TM Manufacturer: Teknik Makina (Teknik Cutting Tools) Product designation: SDJCL 2525 / SDJC for DCMT inserts SKU: AP517TM Weight: 0.735 kg Data Shank dimensions: 25 × 25 mm Cutting head width: 32 mm Cutting height: 35 mm Overall length: 150 mm Cutting angle: 93° Direction: Left‑hand Special features Internal coolant: yes Suitable for: DCMT 11T3 indexable inserts Clamping plate: TA030 Torx key: T15 Torx screw: M3.5×11 Boring bar interface: M11 FAQ What insert type fits this holder? The holder is designed specifically for DCMT 11T3 indexable inserts and secures them with the SDJC clamping arrangement. Is the coolant internal or external? This toolholder features internal coolant, delivering cutting fluid directly to the insert seat and cutting edge to assist cooling and chip control. Which orientation is the holder for? The SDJCL 2525 is configured for left‑hand turning operations and is suitable for external turning and facing tasks. What are the key mounting features? Mounting uses a Torx T15 drive with an M3.5×11 screw; the holder is compatible with M11 boring bar interfaces and the TA030 clamping plate. Can this holder be used on CNC lathes? Yes — the compact 25 × 25 mm shank and standardised ISO dimensions make it suitable for turret and toolpost mounting on CNC turning centres. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Benefit from internal coolant and a precise fit for DCMT indexable inserts; the robust shank and a defined 32 mm cutting height deliver stable, repeatable turning results. Order the Klemmhalter SDJCL 2020 directly via Metav Werkzeuge or ask our consultants if needed. Klemmhalter SDJCL 2020 — Left‑hand toolholder with internal coolant (Teknik Makina) Klemmhalter SDJCL 2020 is a left‑hand toolholder for turning applications, designed for use with DCMT 11T3 indexable inserts and internal coolant supply Left‑hand cutting orientation Internal coolant supply For DCMT 11T3 indexable inserts ISO SDJCL 2020 designation Enhanced process stability through coolant delivery The integrated internal coolant channel ensures consistent lubrication and chip evacuation directly at the cutting edge, reducing heat and improving tool life. With a focused coolant feed, the holder supports longer uninterrupted runs and fewer tool changes, which contributes to higher machine uptime. This section highlights the holder’s capacity to maintain cutting conditions, rather than only listing dimensions, so production planners can expect more reliable cycle times and reduced rework. Accurate geometry for repeatable turning results Built to the ISO SDJCL 2020 profile, the clamping geometry offers a secure seat for DCMT 11T3 inserts and a repeatable insert position. The defined cutting height of 32 mm and a cutter head width of 25 mm guarantee consistent cutting geometry across batches. For work requiring tight tolerances, the stable insert clamping minimises deflection and supports predictable toolpath outcomes, which simplifies process qualification and shortens setup times. Compact design that fits workshop workflows With an overall length of 125 mm and a compact shank, the holder offers a balance between accessibility and rigidity in confined turret stations. The modest weight of 0.404 kg contributes to low centrifugal loads during high‑speed rotations while the left‑hand orientation and 93° cutting angle optimise chip flow for typical turning operations. The combination of compact size and solid construction supports flexible machine set‑ups and easier handling during indexable insert changes. Ready for integration and secure fastening Delivery features suitable fastening details for a fast fit on compatible tool posts: the holder accepts a Torx T15 drive and is secured with an M3,5x11 screw, while the U‑plate designation TA030 and toolbar rod reference K11 indicate common mounting interfaces. These attributes reduce adaptation effort when switching holders or integrating into existing turning stations, helping maintenance teams implement changes with minimal downtime. For reliable left‑hand turning with internal coolant, order the Teknik Makina SDJCL 2020 through Metav Werkzeuge — contact our team in Emmerich at info@metav-werkzeuge.com or +49 2822 7131930 for application advice Technical Data Article number: AP516TM Manufacturer: Teknik Makina Product designation: SDJC for DCMT Indexable Inserts ISO designation: SDJCL 2020 Facts Overall length: 125 mm Cutting height: 32 mm Holder height: 20 mm Head width: 25 mm Shank width: 20 mm Weight: 0.404 kg Cutting angle: 93° ECLASS: 21181004 Suitable inserts: DCMT 11T3 Screw: M3,5x11 Torx key: T15 Special features Internal coolant Left‑hand cutting direction U‑plate: TA030 Toolholder rod: K11 Designed for DCMT 11T3 indexable inserts FAQ Which insert types are compatible with this holder? The holder is designed for DCMT 11T3 indexable inserts; the SDJCL 2020 geometry ensures secure seating for these inserts on Teknik Makina holders (AP516TM) Is the coolant delivered to the cutting edge? Yes — the Klemmhalter SDJCL 2020 features internal coolant delivery that channels fluid directly to the insert area to improve cooling and chip control Can the holder be mounted on standard toolposts? Mounting uses common interfaces: the U‑plate designation TA030 and toolholder rod K11 align with many turret systems for straightforward installation What orientation is the holder made for? This toolholder has a left‑hand cutting orientation and a 93° cutting angle, optimised for left‑hand turning operations Which torque or driver is required for the clamping screw? The holder uses an M3,5x11 screw with a Torx T15 drive for clamping and insert fastening Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Combine accurate clamping geometry, internal coolant and compatibility with DCMT 11T3 inserts for dependable left-hand turning operations; order directly via Metav Werkzeuge or consult the technical advisors for application support. Klemmhalter AP515TM — SDJC holder for DCMT indexable inserts, left-hand, 16 x 16 mm (Teknik Cutting Tools) The Klemmhalter AP515TM is a left-hand SDJC clamping holder engineered for turning with DCMT 11T3 indexable inserts, optimised for controlled coolant delivery and compact 16 x 16 mm mounting. SDJCL 1616 shank, 16 x 16 mm Designed for DCMT 11T3 indexable inserts Internal coolant supply for chip control Left-hand turning with 93° cutting angle Precision that shortens setup and keeps tolerances tight The AP515TM combines a compact 16 x 16 mm shank and a consistent cutting height of 32 mm to provide repeatable tool positioning across serial production. The ISO designation SDJCL 1616 identifies the holder geometry for straightforward tool selection and machine programming. With an overall length of 100 mm and a lightweight construction at 0.204 kg, the toolholder minimises overhang while maintaining rigidity, which reduces vibration and supports stable cutting forces. Compatibility with DCMT 11T3 inserts ensures easy sourcing of cutting edges and predictable performance in left-hand turning applications. Controlled coolant and chip management for longer tool life Integrated internal coolant channels deliver cutting fluid directly to the insert seat, improving cooling at the cutting zone and promoting efficient chip evacuation. This direct feed helps to lower thermal load on the insert and workpiece, which in turn extends the service life of indexable tips and reduces the risk of built-up edge. The specified 93° cutting angle supports secure engagement on shoulder and profile cuts while the holder geometry directs chips away from the tool flank, resulting in fewer interruptions for cleaning and less rework downstream. Secure clamping and straightforward service routines Clamping is achieved using the supplied retention hardware and a TA030 support plate, with a Torx fastener system (key T15) and a retention screw M3.5x11 for positive, repeatable seating. The toolholder accepts standard DCMT tips and is compatible with shank designation H11 for the relevant boring bar series, simplifying inventory and reconditioning workflows. The mechanical design facilitates rapid insert changes and controlled torque application, which shortens maintenance intervals and reduces unplanned downtime while preserving cutting geometry. Practical fitment in production environments Built for workshops and production turning centres that require a compact left-hand option, this SDJC holder suits applications that use industry-standard DCMT inserts for general turning and profiling tasks. The combination of compact dimensions, internal coolant and standardised mounting makes the holder a practical choice where setup speed and process stability are priorities. For operations aiming to consolidate tooling without sacrificing reliability, the AP515TM integrates with common tool post systems and supports an efficient workflow from set-up through series production. For dependable left-hand turning with internal coolant, contact Metav Werkzeuge to secure supply of the Teknik Cutting Tools SDJCL 1616 holder AP515TM — call +49 2822 7131930 or email info@metav-werkzeuge.com Technical data Article number: AP515TM Manufacturer: Teknik Makina Description: SDJC for DCMT Indexable Inserts Facts Shank / holder height: 16 mm Cutting-head width: 16 mm Holder width: 16 mm Cutting height: 32 mm Overall length: 100 mm Weight: 0.204 kg Cutting angle: 93° Special features Compatible inserts: DCMT 11T3 ISO designation: SDJCL 1616 Internal coolant: yes Cutting direction: left-hand U-plate: TA030 Torx key: T15 Torx screw: M3.5x11 Boring-bar designation: H11 FAQ Which inserts fit this holder? The AP515TM is specified for DCMT 11T3 indexable inserts and accepts the common DCMT geometry for standard turning tasks. Is coolant supported through the toolholder? Yes, the holder features internal coolant delivery to the insert seat for improved cooling and chip control. Can the holder be used for right-hand turning? This item is configured for left-hand turning; for opposite-direction operations a right-hand equivalent should be selected. What fasteners are required for clamping? Clamping uses a Torx retention screw M3.5x11 tightened with a T15 key and the matching TA030 support plate. What is the ISO designation for ordering and setup? The ISO identifier is SDJCL 1616, which aids in matching the holder to compatible tool posts and machine fixtures. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of the combination of robust right-hand turning geometry, reliable internal coolant and ISO SDJCR 2525 compatibility for consistent cycle times and predictable tool life — order the toolholder directly via Metav Werkzeuge or contact our advisors for tailored integration advice. AP512TM — SDJCR 2525 turning toolholder (right-hand, internal coolant) by Teknik Makina The AP512TM is a right-hand SDJCR 2525 turning toolholder engineered for ISO DCMT 11T3 indexable inserts, intended for precision external turning in production and job-shop environments. Right-hand turning configuration Internal coolant supply Compatible with DCMT 11T3 inserts Solid 25 x 25 mm SDJCR 2525 shank Improved process stability through coolant-fed chip control The integrated internal coolant channel delivers coolant directly to the cutting zone, supporting reliable chip evacuation and reducing heat build-up. For production environments this means longer insert life and fewer unscheduled tool changes; when using DCMT 11T3 inserts the coolant feed helps maintain cutting-edge integrity during prolonged cuts. The design is therefore suited to repetitive turning tasks where maintaining consistent surface finish and cycle times is a priority. Secure clamping for repeatable accuracy Clamping is handled by the TA030 clamp plate and an M3.5x11 Torx screw, tightened with a T15 key, providing a robust and repeatable seat for the insert. This mechanical arrangement reduces micro-movement under load and ensures repeatability between insert changes, which translates into stable part tolerances and reduced rework. The solid interface is beneficial when machining with intermittent cuts or under higher radial forces. Geometry tuned for precision turning results The toolholder’s geometry — a 93° cutting angle and a set cutting-edge height 35 mm — positions the insert for controlled engagement and predictable chip formation. The right-hand orientation and the SDJCR format deliver an optimised approach angle for external contours and shoulder work, helping to achieve tight dimensional control without complex tool set-ups. Compact format with straightforward integration With a compact 150 mm length and a mass of 0.735 kg, the holder balances stiffness and accessibility for confined tool stations. The SDJCR 2525 designation reflects the 25 x 25 mm shank dimensions for standard turret and toolpost systems, and compatibility with M11-IK boring-bar interfaces simplifies integration into existing toolbanks. For workshops that prioritise quick insert swaps and minimal inventory, this indexable insert holder supports efficient tool management and predictable maintenance intervals. The AP512TM is therefore a practical choice for both small batch and continuous turning operations. Contact Metav Werkzeuge in Emmerich for purchasing or technical advice on Teknik Makina’s SDJCR 2525 right-hand toolholder — email info@metav-werkzeuge.com or call +49 2822 7131930 to discuss integration and delivery from the Emmerich warehouse Technical Data Article number: AP512TM Manufacturer: Teknik Makina ISO designation: SDJCR 2525 Facts Shank dimensions: 25 x 25 mm Head width: 32 mm Toolholder height: 25 mm Cutting-edge height: 35 mm Overall length: 150 mm Weight: 0.735 kg Cutting angle: 93° Features Internal coolant: yes Compatible inserts: DCMT 11T3 Clamp plate: TA030 Torx screw: M3,5x11 Torx key size: T15 Orientation: right-hand Boring bar compatibility: M11-IK FAQ Which insert type fits this toolholder? The AP512TM is designed for DCMT 11T3 indexable inserts and secures them with the TA030 clamp plate and M3.5x11 Torx screw. Is there internal coolant on this holder? Yes, the toolholder features internal coolant supply to the cutting zone to aid chip evacuation and prolong insert life. What are the shank dimensions and fitting standard? The holder uses a 25 x 25 mm shank, specified by the ISO designation SDJCR 2525, for standard turret and toolpost mounting. Which screw and key are required for insert clamping? Clamping is performed with an M3.5x11 Torx screw; a T15 Torx key is the correct tool for assembly and torque application. Is the AP512TM suitable for heavy cuts? The rigid clamping system and solid 25 x 25 mm shank provide good stiffness for demanding turning operations; however, final suitability depends on cutting parameters and insert grade. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a coolant-fed, right-hand clamping solution that combines secure insert retention and compact dimensions for stable turning operations; order the SDJCR 2020 directly via Metav Werkzeuge or consult our tooling specialists for application advice. SDJCR 2020 clamping holder — SDJC tool holder for DCMT 11T3 inserts, right-hand, internal coolant (Teknik Cutting Tools) SDJCR 2020 clamping holder is a right-hand turning tool holder designed for DCMT indexable inserts; suitable for precise external turning where coolant feed and rigid clamping are required SDJC design for DCMT 11T3 inserts Right-hand turning orientation Integrated internal coolant feed Robust 20 x 20 mm shank for stability Secure insert seating for consistent machining The holder’s SDJCR 2020 geometry is tuned for stable clamping of DCMT 11T3 indexable inserts, delivering predictable seating and repeatable cutting performance. The clamping arrangement and the supplied M3.5x11 fixing screw ensure the insert is retained with minimal movement, which reduces vibration and protects the cutting edge. Compatibility with a widely used insert size simplifies tooling logistics and supports quicker tool set-up in small-series and production environments alike. Compact dimensions that improve toolpath reliability A compact but robust design—with a 20 x 20 mm shank, 25 mm cutting-head width and 125 mm overall length—provides a favourable stiffness-to-length ratio for turning tasks. The modest mass (approx. 0.404 kg) and precise geometry help to lower deflection under load, which in turn supports tighter tolerances and longer tool life. For workshop planners the short footprint and standard shank size make toolholder exchange and turret programming straightforward. Built-in coolant and serviceable components for uptime The internal coolant channel promotes efficient chip evacuation and targeted cooling at the insert rake zone, which can extend insert life and improve surface finish on difficult-to-machine materials. Practical service features—such as the T15 Torx drive for the clamp screw and the U-plate reference TA030—allow fast insert changes and straightforward maintenance. The holder’s 93° cutting angle and 32 mm cutting-edge height align with common lathe set-ups, reducing the need for supplementary fixtures or offsets. For coolant-fed right-hand turning where consistent insert retention matters, contact Metav Werkzeuge in Emmerich to request the SDJCR 2020 from Teknik Cutting Tools and discuss the best insert and clamp combinations for the intended application. Technical data Article number: AP511TM Manufacturer: Teknik Makina ISO designation: SDJCR 2020 Facts Overall length: 125 mm Shank: 20 x 20 mm Cutting head width: 25 mm Cutting-edge height: 32 mm Cutting angle: 93° Weight: 0.404 kg Special features For indexable inserts: DCMT 11T3 Direction: right-hand turning Internal coolant: yes Torx key: T15 Screw: M3.5x11 U-plate reference: TA030 Compatible toolholder bar: K11-IK FAQ What inserts fit this holder? The SDJCR 2020 clamping holder accepts DCMT 11T3 indexable inserts; the geometry and clamp screw configuration are matched to that insert designation. Is this holder for right-hand or left-hand turning? This tooling is configured for right-hand turning operations, as indicated by the SDJC orientation. Does the tool holder provide internal coolant? Yes — the holder features internal coolant feed to the insert zone to aid chip control and tool life. What shank size is required for the turret? The holder has a 20 x 20 mm shank and is intended for toolposts or turrets that accept that standard square shank. Which fastener and key are used for the clamping screw? Clamping uses an M3.5x11 screw secured with a T15 Torx key for reliable insert retention. What is the article number for reordering? The SKU for this product is AP511TM, handy for procurement and inventory management. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a compact left-hand turning solution with 30 mm cutting height and a 150 mm overall length for stable machining and simple integration; order the clamp holder directly via Metav Werkzeuge or consult the technical team for alignment and delivery. Clamp holder SDJCL 2525 — SDJC for DCMT Indexable Inserts (left-hand) by Teknik Makina The clamp holder SDJCL 2525 is a left-hand turning toolholder designed for secure use with DCMT 11T3 indexable inserts in conventional and CNC lathes. Left-hand turning orientation For DCMT 11T3 indexable inserts Cutting height 30 mm Overall length 150 mm Precise clamping for consistent surface finishes The SDJCL 2525 toolholder combines a rigid clamping geometry with a defined cutting height 30 mm to maintain a constant tool tip position during turning operations. This precision clamping reduces set-up time and minimises run-out, which helps to keep repeatability high when changing inserts. Compatibility with standard DCMT 11T3 indexable inserts simplifies tooling choices and supports consistent surface quality across batches. The left-hand configuration ensures correct rake and approach geometry for left-hand turning tasks. Predictable chip flow and stable cutting behaviour An accurately specified 93° cutting angle and robust head dimensions (head width 32 mm) promote predictable chip formation and assist in maintaining steady cutting forces. Stable chip control lowers chatter risk and supports longer insert life by avoiding irregular loads at the cutting edge. The toolholder’s geometry is designed to work in tandem with negative-indexable inserts, meaning that cutting forces are directed into the holder body for superior rigidity under moderate to heavy cuts. Compact construction for easy machine integration A compact profile with a holder width of 25 mm and an overall length 150 mm enables straightforward installation in tight tool turrets and gang setups. The clamping screw thread (M11) and the ISO designation SDJCL 2525 conform to common workshop practices, simplifying retrofitting and repeatable mountings. With a mass of 0.735 kg, the component balances inertia and rigidity to suit a wide range of turning operations while keeping dynamic loads manageable for many turret systems. Designed for reliable workshop use The product supports a clear tool specification approach: SDJCL 2525 identifies the holder geometry, while the use of DCMT 11T3 inserts provides broad availability of grades and chipbreakers to match workpiece materials. The combination of measurable dimensions—cutting height, head width and overall length—offers a verifiable basis for tooling plans and machining simulations. For production environments seeking dependable, repeatable turning results, the holder contributes to process stability and predictable tool change behaviour. For workplaces requiring a left-hand turning toolholder from Teknik Makina, contact Metav Werkzeuge for exact-fit advice and dependable supply from Emmerich — email info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: D368TM Manufacturer: Teknik Makina ISO designation: SDJCL 2525 For inserts: DCMT 11T3 Facts Cutting height: 30 mm Head width: 32 mm Holder width: 25 mm Overall length: 150 mm Weight: 0.735 kg Cutting angle: 93° Cutting direction: left Clamping screw thread: M11 Special features Left-hand turning orientation Compatible with DCMT indexable inserts ISO toolholder designation SDJCL 2525 Compact profile for turret integration FAQ What insert type fits this holder? The SDJCL 2525 clamp holder accepts DCMT 11T3 indexable inserts; the holder geometry is matched to the insert form for secure seating and repeatable positioning. Is the clamp holder suitable for CNC turret systems? Yes — the compact dimensions (overall length 150 mm, head width 32 mm) and standard M11 clamping make the holder appropriate for many turret and gang-tool setups in CNC turning centres. Which cutting direction is supported? This holder is configured for left-hand turning operations; the orientation aligns the insert rake and clearance for left-hand cuts. How does the cutting height affect setup? A defined cutting height of 30 mm ensures the insert tip sits at a consistent reference plane, simplifying turret alignment and reducing the need for shim adjustments. Can the holder be used with different DCMT insert grades? Yes — the holder accepts standard DCMT 11T3 grades and chipbreaker styles, allowing selection of carbide grades suited to the workpiece material and machining parameters. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a compact, left‑hand clamping toolholder that combines precise compatibility with DCMT 11T3 indexable inserts, a 93° cutting approach and a slim 20 mm shank for stable turning. Order directly via Metav Werkzeuge or consult the team for tailored application advice. SDJCL 2020 clamping toolholder by Teknik Makina — left‑hand, for DCMT 11T3 inserts, 125 mm overall length The SDJCL 2020 clamping toolholder is a left‑hand turning holder engineered for use with DCMT 11T3 indexable inserts, providing a compact 125 mm profile for space‑saving external turning setups. For DCMT 11T3 indexable inserts Left‑hand cutting orientation 125 mm overall length Robust 20 mm shank height Maximum rigidity with a compact profile The holder is designed to deliver rigidity in a compact form: an overall length of 125 mm and a 20 mm shank height combine to reduce overhang while maintaining stability during external turning. A cutting angle of 93° helps position the insert for predictable engagement, which reduces vibration and supports consistent surface finish. The holder’s modest mass (approximately 0.404 kg) balances inertial damping with ease of handling, making it suitable for short‑run changeovers and repetitive production tasks where tool stability is critical. Quick, repeatable insert clamping for efficient production Clamping systems determine how reliably an insert holds its geometry under load. This toolholder is specified for DCMT 11T3 indexable inserts and the ISO designation SDJCL 2020 identifies the shank form and mounting interface. The design emphasises repeatable seating and secure fixing, which minimises index‑to‑index variation and accelerates tool changes. Reduced downtime and fewer adjustments translate into tangible productivity benefits: more consistent cycle times and less part rework in series turning. Predictable cutting geometry for consistent results Using a standard insert size like DCMT 11T3 allows for predictable approach and chip control across different machines and operators. The toolholder’s head width (25 mm) and cutting height (25 mm) align the insert at the intended datum height, ensuring the correct engagement angle without additional shims. For engineers and machinists who depend on repeatable set‑ups, this stability simplifies process planning and supports consistent part tolerances over extended runs. Built for workshop reliability and straightforward integration The clamping toolholder’s ISO coding (SDJCL 2020) and its direct compatibility with common indexable inserts make it easy to integrate into existing tool stations and turret configurations. The left‑hand orientation suits operations where tool path and lathe set‑ups require a reversed approach. Combined with Metav’s logistical and quality oversight, the holder is presented as a dependable component for both independent workshops and production departments seeking a dependable supply chain and consistent product quality. For secure delivery and application guidance, contact Metav Werkzeuge — the partner for democratised precision and reliable European supply: eMail info@metav-werkzeuge.com or call +49 2822 7131930 to discuss suitability for specific turning tasks and machine interfaces. Technical data Article number: D366TM Manufacturer: Teknik Makina ISO designation: SDJCL 2020 Compatible inserts: DCMT 11T3 Cutting direction: left SKU: D366TM Facts Overall length: 125 mm Shank height: 20 mm Shank width: 20 mm Head width: 25 mm Cutting height: 25 mm Cutting angle: 93° Weight: 0.404 kg Special features SDJC design for DCMT indexable inserts Left‑hand cutting orientation Compact, space‑saving profile Repeatable clamping interface Teknik Makina product FAQ What inserts fit this holder? The holder is compatible with DCMT 11T3 indexable inserts; the SDJCL 2020 interface secures the DCMT geometry for predictable cutting performance. Is this holder suitable for right‑hand turning? This specific toolholder is manufactured for left‑hand cutting orientation; a right‑hand version is required for conventional right‑hand turning. What is the overall length and shank size? The toolholder has an overall length of 125 mm and a shank height/width of 20 mm, balancing reach with rigidity for external turning. How does the clamping system affect productivity? The clamping interface on the SDJCL 2020 minimises index‑to‑index variation, enabling faster insert changes and more consistent cycle times when used with DCMT 11T3 inserts. Can the holder be integrated into existing turrets? Yes — the ISO designation and standard shank dimensions facilitate integration into common turret mounts and lathe tool stations provided the turret accommodates a 20 mm shank. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Combine stable 16 × 16 mm shank rigidity, compatibility with DCMT 11T3 indexable inserts and a precise 93° cutting angle to secure reliable left-hand external turning — order via Metav Werkzeuge or consult our specialists for application support. SDJCL 1616 clamping holder — SDJC for DCMT indexable inserts, left-hand, 93° cutting angle The SDJCL 1616 clamping holder is a left-hand toolholder for DCMT 11T3 indexable inserts, designed for stable external turning and straightforward insert changes in workshop and light industrial lathe work. Left-hand turning orientation Compatible with DCMT 11T3 inserts Shank 16 × 16 mm for stable clamping 100 mm overall length for external turning Secure clamping for consistent surface quality The holder is engineered to deliver clamping stability through its 16 × 16 mm shank and compact head geometry, which reduces micro-movement during cuts. With a cutting height 25 mm and a well-defined seating for the insert, the arrangement promotes repeatability from one set-up to the next, translating into improved surface finish and longer insert life. This stability is particularly valuable in batch production and repair work where consistent results matter. Tailored for DCMT inserts and left-hand cutting Compatibility with DCMT 11T3 indexable inserts ensures access to a broad range of grades and geometries for finishing or medium-duty turning. The left-hand configuration and 93° cutting angle give the cutting edge the clearance and support required for secure external turning, while the insert pocket design simplifies indexing and reduces downtime associated with insert changes. The result is a combination of flexibility and operational efficiency for common turning tasks. Reach and rigidity to boost productivity A 100 mm overall length provides practical reach without excessive overhang, helping to minimise leverage and reduced vibration during cuts. At a weight of 0.204 kg the unit balances rigidity with manageable mass for rapid tool changes. Together, these attributes contribute to a cost-efficient machining process: fewer rejects, steadier feeds and the option to run higher effective cutting parameters within the stability limits of the lathe. Quick installation and workshop compatibility The clamping system accepts bar designation H11 and follows established ISO sizing as SDJCL 1616, enabling straightforward integration into existing toolposts and quick-change setups. Its form factor and simple insert access make it suitable for precision workshops, maintenance departments and small-scale production, where dependable toolholding and easy servicing support tight schedules and predictable maintenance intervals. For tailored advice or to order this Teknik Makina SDJCL 1616 clamping holder via Metav Werkzeuge, please contact Metav Werkzeuge directly at info@metav-werkzeuge.com or call +49 2822 7131930 for expert guidance and fast supply from Emmerich. Technical data SKU: D364TM Manufacturer: Teknik Makina Article designation: SDJC for DCMT Indexable Inserts ISO designation: SDJCL 1616 Facts Shank height: 16 mm Shank width: 16 mm Cutting head width: 20 mm Cutting height: 25 mm Overall length: 100 mm Cutting angle: 93° Weight: 0.204 kg Cutting direction: left Special features Left-hand toolholder For DCMT 11T3 indexable inserts Bar designation: H11 FAQ Which indexable inserts fit this holder? The holder is designed for DCMT 11T3 indexable inserts; the SDJCL 1616 seating supports standard DCMT geometry for quick indexing and replacement. Is this toolholder for left- or right-hand turning? This version is left-hand; the SDJCL 1616 is configured for left-hand cutting operations with a 93° cutting angle. What are the essential dimensions to check before ordering? Key dimensions are shank 16 × 16 mm, cutting head width 20 mm, cutting height 25 mm and overall length 100 mm — SKU D364TM. Which applications suit this clamping holder? The holder is suitable for external turning on lathes in precision workshops and small-scale production, where DCMT inserts provide flexible grades and edge geometries. How does the 93° cutting angle affect performance? A 93° cutting angle provides clearance and robust support at the insert corner, improving edge strength for general external turning while helping to avoid interference with workpiece features. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a robust left-hand SDJC design and precise ISO sizing to ensure stable turning with DCMT inserts; its compact 12 × 12 mm shank and 110 mm overall length support repeatable set-ups and straightforward integration into existing toollines — order directly via Metav Werkzeuge or consult our specialists for supply and compatibility advice Clamping holder SDJCL 1212 — SDJC for DCMT 11T3, left-hand, 12 × 12 mm The Clamping holder SDJCL 1212 is a left-hand SDJC toolholder designed for turning operations with DCMT 11T3 indexable inserts, optimised for stable clamping and predictable chip control in production and workshop environments Left-hand SDJC design for turning Compatible with DCMT 11T3 indexable inserts 12 × 12 mm shank for standard toolposts 110 mm overall length for compact set-ups Consistent cutting performance for left-hand turning The SDJCL 1212 offers a reliably rigid geometry that translates into consistent cutting behaviour and improved surface quality. The left-hand orientation and a cutting angle of 93° position the insert for controlled engagement, which reduces radial loads and supports predictable chip flow. For production environments this means fewer surprises at the lathe: cycle times remain stable and rework is reduced. The holder’s design focuses on repeatability rather than cosmetic features, so setup time and variability between operators are minimised. Secure clamping and reduced downtime through clear dimensions A secure clamping system and clearly defined dimensions enable fast insert changes and repeatable tool offsets. The holder features a 12 mm clamp height and a 12 × 12 mm shank, combined with a 16 mm cutting-head width and a 20 mm cutting height that together deliver a compact, stiff assembly. The modest weight of 0.132 kg and 110 mm overall length make it suitable for multi-tool turrets and smaller toolposts where balance and accessibility matter. These measurable values make programming, presetting and tool management straightforward for workshop staff. Broad compatibility and dependable sourcing for production use Compatibility is concise: the holder is made for DCMT 11T3 indexable inserts and carries the ISO designation SDJCL 1212, simplifying tool selection and procurement. Its designation and dimensions facilitate integration into existing tooling layouts without guesswork. Supplied by Teknik Cutting Tools and available through Metav Werkzeuge, the component benefits from a European supply chain that emphasises consistent stock and predictable delivery — a practical advantage when tool replacements must be swift to avoid production downtime. For reliable left-hand turning with DCMT indexable inserts, contact Metav Werkzeuge to discuss availability and ensure the SDJCL 1212 is matched to the intended application Technical data SKU: D362TM ISO designation: SDJCL 1212 For inserts: DCMT 11T3 Cutting direction: left Facts Overall length: 110 mm Shank: 12 × 12 mm Clamp height: 12 mm Cutting-head width: 16 mm Cutting height: 20 mm Weight: 0.132 kg Cutting angle: 93° Special features SDJC clamping holder for indexable inserts J11 toolholder bore designation Left-hand turning configuration Compact, stiff design for predictable set-ups FAQ Which inserts fit this holder? The holder accepts DCMT 11T3 indexable inserts; the designation SDJCL 1212 matches the common insert geometry for turning applications. Is this toolholder for left- or right-hand turning? This SDJC clamping holder is configured for left-hand cutting operations as specified by its orientation. What are the shank and clamp dimensions? The shank measures 12 × 12 mm with a clamp height of 12 mm, giving a compact and repeatable mounting reference. What is the SKU and how is the holder identified? The article is listed as D362TM and identified by the ISO designation SDJCL 1212 for clear procurement and presetting. What length and weight should be expected when balancing a turret? Expect an overall length of 110 mm and a weight of 0.132 kg, suitable for compact tool arrangements and minimal inertia effects. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Take advantage of the combination of precise insert compatibility, a stable 25 x 25 mm shank and a compact 150 mm overall length for reliable turning operations; order directly via Metav Werkzeuge or consult the team for application advice. SDJCR 2525 clamping toolholder – SDJC for DCMT indexable inserts (right-hand) The SDJCR 2525 clamping toolholder is a right-hand turning holder designed to accept DCMT 11T3 indexable inserts for medium-duty external turning and facing tasks in general workshop and production environments. Compatible with DCMT 11T3 indexable inserts Right-hand cutting orientation Robust 25 x 25 mm shank 150 mm overall length for extended reach Consistent chip control and repeatable geometry for efficient turning The holder is engineered to secure DCMT 11T3 inserts with a stable clamping interface, which reduces micro-movement and improves surface finish on serial components. The 93° cutting angle provides a balanced approach between clearance and cutting force, helping to maintain tool life under typical machining feeds. In practice, a dependable clamping design lowers rework rates by limiting insert chatter, and the result is a more predictable process that supports tighter tolerances on turned parts. Rigid shank and compact length to increase stability and access A 25 x 25 mm shank combined with a 150 mm overall length gives a sturdy yet compact footprint for lathe setups where access and rigidity matter. The moderate mass of 0.735 kg contributes to vibration damping without making tool changes cumbersome. The 32 mm cutting head width and 30 mm cutting height are matched to the insert geometry so cutting forces are transferred evenly into the holder; this reduces edge wear on inserts and allows consistent finishing passes with fewer tool adjustments. Fast mounting and straightforward integration with standard toolposts The turning holder includes an M11 mounting characteristic for straightforward attachment where compatible posts or adapters are used, and the SDJC clamping concept allows quick insert indexing and replacement. For production environments, reduced downtime during insert changes and the use of standard DCMT 11T3 sizes mean less inventory complexity and faster cycle recovery. The combination of standard interface and robust construction supports reliable throughput and simplifies tooling management on the shopfloor. For supply and technical guidance on Teknik Cutting Tools' SDJCR 2525 clamping toolholder, contact Metav Werkzeuge in Emmerich at info@metav-werkzeuge.com or +49 2822 7131930 to discuss compatibility with specific lathes and insert grades Technical Data Article number: D228TM Manufacturer: Teknik Makina ISO designation: SDJCR 2525 ECLASS: 21181004 Data Shank width: 25 mm Shank height: 25 mm Overall length: 150 mm Cutting head width: 32 mm Cutting height: 30 mm Cutting angle: 93° Weight: 0.735 kg Suitable for inserts: DCMT 11T3 Mounting thread: M11 Cutting direction: right Special features SDJC clamping concept for DCMT inserts Right-hand turning configuration Compact, rigid construction for reduced vibration FAQ Which insert size fits this holder? The SDJCR 2525 clamping toolholder accepts DCMT 11T3 indexable inserts as the standard size for its clamping pocket. Is the holder suitable for right-hand turning only? Yes, the holder is configured for a right-hand cutting direction and is intended for external turning and facing in that orientation. What are the shank dimensions and overall length? The holder features a 25 x 25 mm shank and an overall length of 150 mm, providing a compact but rigid setup for many lathe toolposts. How does the SDJC clamping system affect tool change time? The SDJC clamping design allows quick indexing and secure retention of inserts, which reduces changeover time and supports higher machine uptime. Can this holder be mounted to standard toolposts? The holder uses an M11 interface characteristic and is compatible with standard mounting arrangements where that thread or corresponding adapter is accepted. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a precision toolholder that combines compatibility with DCMT inserts, reliable right-hand turning geometry and a compact form factor for stable machining. Order directly via Metav Werkzeuge or consult our specialists for a tailored supply solution. Clamping holder SDJC for DCMT Indexable Inserts — Right-hand, SDJCR 2020 The clamping holder SDJC for DCMT indexable inserts is a right-hand toolholder engineered for turning operations with DCMT 11T3 inserts, delivering stable cutting geometry and simple insert clamping for workshop and production use. Right-hand cutting orientation For DCMT 11T3 indexable inserts Overall length 125 mm for stability Robust 20 mm holder width Stable clamping for repeatable turning results The SDJCR 2020-style toolholder is designed to secure DCMT 11T3 indexable inserts with a consistent clamp force and minimal play. Thanks to its overall length of 125 mm and compact cross-section, the holder provides a steady tool projection that reduces vibration and improves surface finish in turning operations. The cutting angle of 93° helps to position the insert for conventional turning passes while maintaining favourable chip flow; this geometry is particularly useful where predictable toolpath behaviour is required. Clear mechanical interfaces and a standard ISO designation facilitate integration into existing tool setups. Precision dimensions that support process reliability Key dimensions are tuned for workshop interchangeability: a holder height of 20 mm, head width 25 mm and holder width 20 mm combine to create a slim yet rigid toolbody. The cutting height of 25 mm ensures the insert seat aligns correctly with common lathe tool heights, reducing setup time and the need for shims. With a measured mass of 0.404 kg, the holder balances inertia and responsiveness, which helps to maintain concentricity across a range of spindle speeds. These measurable properties translate into predictable tool behaviour and make the holder suitable for both single-part turning and small-series production. Compatibility and easy fitting for efficient shop workflows Intended specifically for DCMT 11T3 inserts, the clamping design supports fast insert changes and secure positioning for repeatable cycles. The toolholder is configured for right-hand cutting direction and is compatible with bar-stock mounting schemes referenced by the K11 bore-bar designation, enabling straightforward retrofitting to common tool posts and boring bars. The SDJC clamping principle gives a firm grip on the insert corner, reducing the risk of insert movement under load and simplifying maintenance routines by standardising spare-part inventories. Robust design that reduces downtime and simplifies logistics Constructed to industry norms and identified by the ISO code SDJCR 2020, this toolholder lets purchasing and engineering teams standardise on a recognised tool format. The combination of well-documented dimensions and a compact footprint assists in planning toolpaths, fixture clearances and stocking. Reduced setup variability and standard compatibility lower the frequency of corrective adjustments, which supports higher machine uptime and a more predictable production flow. For procurement or technical clarification, contact Metav Werkzeuge for product availability, compatibility advice and ordering: Metav Werkzeuge will advise on delivery options and precise fitting details Technical data SKU: D226TM Type: SDJC for DCMT indexable inserts ISO designation: SDJCR 2020 Manufacturer: Teknik Makina Dimensions & core data Overall length: 125 mm Cutting height: 25 mm Holder height: 20 mm Head width: 25 mm Holder width: 20 mm Weight: 0.404 kg Cutting angle: 93° Compatibility & features For DCMT 11T3 inserts Right-hand cutting direction Bore-bar designation: K11 Clamping type: SDJC FAQ Is this holder suitable for DCMT 11T3 inserts? Yes. The clamping holder SDJC for DCMT indexable inserts is specified for use with DCMT 11T3 inserts and secures the insert corner for turning tasks. What is the cutting direction of the holder? The toolholder is configured for right-hand cutting operations, matching the SDJCR 2020 ISO orientation. Which dimensions determine installation height and stability? Key dimensions are cutting height 25 mm, holder height 20 mm and overall length 125 mm, which together influence tool projection and stability during turning. Can the holder be mounted on standard bar systems? Yes. The product references bore-bar designation K11, facilitating mounting on compatible bar and toolpost systems used in workshop settings. What is the ISO code for identification and ordering? The holder is identified as SDJCR 2020, which can be used for unambiguous ordering and stock management. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Take advantage of the combination of precise clamping, compact design and proven compatibility with DCMT inserts for efficient turning operations; order directly via Metav Werkzeuge or contact our consultants for application advice. SDJC for DCMT Indexable Inserts — SDJCR 1616 Toolholder by Teknik Cutting Tools, right‑hand cutting, compact 100 mm length SDJC for DCMT Indexable Inserts is a right‑hand clamping toolholder designed for turning with DCMT 11T3 indexable inserts; ideal for shops seeking secure clamping and predictable cutting geometry in confined setups. SDJCR 1616 ISO toolholder Compatible with DCMT 11T3 inserts Right‑hand cutting orientation Compact 100 mm overall length Consistent clamping for repeatable turning results The solidly machined toolholder body provides a stable seat for inserts, ensuring repeatable cutting forces and surface finish. With an ISO designation SDJCR 1616 and compatibility with DCMT 11T3 inserts, the assembly reduces insert play and vibration; this leads to lower tool wear and more consistent part tolerances. The 16 mm holder height and 20 mm cutting‑head width are balanced for rigidity in short‑overhang applications, helping maintain concentricity during medium‑duty turning tasks. Fast setup and predictable cutting geometry A clear advantage of this clamping solution is reduced setup time: the insert pocket and clamping path are engineered to position each DCMT insert precisely, so index changes return the original cutting geometry. The 93° cutting angle supports a controlled chip flow and stable engagement on facing and light profiling, while the right‑hand configuration suits conventional turning directions. For production runs where consistency matters, the predictable tool path shortens process validation and increases uptime. Space‑saving design suited to compact toolposts At an overall length of 100 mm and a net weight of 0.204 kg, the holder is tailored for toolposts with limited clearance. The compact dimensions permit closer tool stacking and easier access on multi‑station turrets. In addition to freeing up workspace, the smaller overhang reduces bending moments, contributing to improved surface finish without altering cutting parameters significantly. Application focus and material compatibility Configured specifically for DCMT 11T3 inserts, this holder excels in general turning tasks on conventional steels and alloyed materials where indexable carbide inserts are standard. The design supports a secure clamping force via the designated clamping screw interface (H11 shank reference), which stabilises the insert under intermittent loads; this is particularly beneficial for batch production and mixed‑series turning where fast insert indexing is required. For application guidance or to specify the SDJCR 1616 holder for a particular lathe or insert grade, contact Metav Werkzeuge — our consultants assist with matching toolholders and inserts for optimal productivity and tool life. Technical data SKU: D224TM Manufacturer: Teknik Makina Article name: SDJC for DCMT Indexable Inserts (SDJCR 1616) Numbers / Core technical data Holder height: 16 mm Holder width: 16 mm Cutting‑head width: 20 mm Cutting height: 25 mm Overall length: 100 mm Weight: 0.204 kg Cutting angle: 93° Cutting direction: right Suitable for: DCMT 11T3 inserts Designs / Special features ISO designation: SDJCR 1616 Shank reference: H11 Indexable insert compatibility: DCMT 11T3 Compact form factor for limited toolpost space FAQ What inserts fit this toolholder? The SDJCR 1616 toolholder is designed to accept DCMT 11T3 indexable inserts, providing correct seating and clamping for standard grades. Is the holder suitable for right‑hand turning only? Yes, the design specifies a right‑hand cutting orientation to match conventional turning directions and toolpost setup. How does the compact length affect performance? The 100 mm overall length reduces overhang, lowering bending moments and improving surface finish compared with longer holders when used in similar cutting conditions. Can this toolholder be used for finishing passes? With its stable clamping and a 93° cutting angle, the holder supports controlled engagement suitable for finishing and light profiling with appropriate insert grades. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a compact, ISO‑rated toolholder that combines standard compatibility with precise geometry for consistent turning results; the robust SDJCR 1212 configuration and a 12 mm shank width ensure stable clamping and predictable chip flow. Order directly via Metav Werkzeuge or contact our consultants for specification support. SDJCR 1212 toolholder by Teknik Makina — right‑hand, for DCMT inserts The SDJCR 1212 is a right‑hand SDJC toolholder designed to accept DCMT 11T3 indexable inserts for precision turning tasks in general machining and workshop environments. SDJCR 1212 ISO designation Right‑hand turning geometry Fits DCMT 11T3 indexable inserts 12 mm shank width, 110 mm overall length Stable clamping for reliable turning results The SDJCR 1212 toolholder is built around a proven clamping concept that secures DCMT 11T3 inserts with consistent alignment. The ISO designation signals compatibility across standard insert ranges, reducing setup time and inventory complexity. With a right‑hand cutting orientation and a straightforward insert seat, the holder delivers repeatable contact between insert and workpiece; this helps to maintain surface finish quality and tool life across serial production and one‑off jobs alike. For workshops seeking predictable performance, the emphasis on standardisation is a clear operational advantage. Compact dimensions that improve rigidity and access Key dimensions—12 mm shank width, 16 mm cutting head width and 110 mm overall length—are balanced to offer stiffness without excessive overhang. The 20 mm cutting edge height and a 93° cutting angle provide a positive geometry for general turning and profiling, allowing controlled chip formation and clearance. A low mass of 0.132 kg means less inertial load on the turret during rapid programme changes, while the compact design aids access in tighter setups. In practice, these measured proportions translate into reduced chatter risk and more stable machining on medium‑duty lathes. Practical workflow benefits and compatibility Designed around the widely used DCMT insert format, this SDJC toolholder makes insert replacement and tool setup straightforward for production and maintenance teams. The shank designation J11 indicates the fitting standard for the mounting bar, simplifying procurement and spare‑part planning. Right‑hand orientation aligns cutting forces predictably for conventional lathe feeds, assisting with toolpath planning and fixture design. By relying on standardised insert geometry and an ISO toolholder, shops can lower logistical friction and focus on cycle‑time optimisation rather than bespoke tooling. Suited for workshops and production environments This toolholder is aimed at machine shops, subcontract manufacturers and maintenance departments requiring dependable turning accessories that integrate into existing toolholding systems. The combination of ISO conformity, compact geometry and insert compatibility supports a broad range of materials and turning tasks when matched with the appropriate DCMT grade. The result is a pragmatic, cost‑efficient upgrade for setups that demand fast changeovers and steady repeatability rather than high‑specialty tooling. For purchase advice or to secure the Teknik Makina SDJCR 1212 toolholder through Metav Werkzeuge—taking advantage of our sourcing and workshop expertise—please contact Metav Werkzeuge GmbH at info@metav-werkzeuge.com or call +49 2822 7131930 for tailored consultation and order support. Technical data Article number: D222TM Manufacturer: Teknik Makina ISO designation: SDJCR 1212 Fits inserts: DCMT 11T3 Shank designation: J11 Key dimensions Shank width: 12 mm Cutting head width: 16 mm Cutting edge height: 20 mm Cutting angle: 93° Overall length: 110 mm Weight: 0.132 kg Compatibility & special features Right‑hand cutting direction SDJC holder type for DCMT inserts ISO‑standard insert seat Compact, high‑stiffness geometry FAQ What insert type does this holder accept? The SDJCR 1212 toolholder accepts DCMT 11T3 indexable inserts and is designed for standard DCMT insert geometry. Is the toolholder right‑hand or left‑hand? This model is supplied in a right‑hand configuration suitable for conventional turning directions. Which shank width and overall length are specified? The holder features a 12 mm shank width and an overall length of 110 mm, offering a compact, stiff arrangement. Can this holder be used across different lathes? Yes; the ISO designation and J11 shank fitting support compatibility with compatible turret bars and holders in many workshop setups. Who manufactures the product and where can it be obtained? The toolholder is produced by Teknik Makina and can be sourced through Metav Werkzeuge; for procurement and specification advice contact Metav Werkzeuge GmbH. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a compact, precision-oriented design that combines stable clamping with quick insert changes and consistent left-hand cutting performance; order the SDJCL 1616 clamping holder via Metav Werkzeuge or consult our technical team for application advice. SDJCL 1616 clamping holder — flat SDJC for DCMT inserts, 16 x 16 mm The SDJC for DCMT Indexable Inserts is a flat, left-hand clamping toolholder for turning operations, intended for use with DCMT 11T3 indexable inserts. Flat SDJC clamping holder for DCMT 11T3 inserts 16 x 16 mm head and shank dimensions Left-hand cutting with 93° cutting angle M5 clamp screw and M3.5x8.5 torx fixing Consistent accuracy through a rigid, compact layout The holder’s 16 x 16 mm head and shank dimensions, combined with a total length of 100 mm, deliver a compact package that reduces overhang and vibration in turning operations. A lower overhang improves repeatability and surface finish, which in turn prolongs insert life and reduces rework. The specified cutting height 25 mm ensures that tool position relative to the workpiece remains stable, making this holder suited to short-reach, high-stability tasks on lathes and turning centres. The design supports predictable machining cycles and fewer rejects in production. Quick, secure clamping to reduce downtime Designed for straightforward insert changes, the holder accepts DCMT 11T3 indexable inserts and secures them with an M5 clamp screw and supporting torx screw (M3.5x8.5) fixed with a T15 key. The clamping plate designation TA030 is specified for correct seating. These standard fittings speed up maintenance and reduce tool-change time in repetitive workflows. The result is a measurable increase in machine uptime and more efficient shift planning for small to medium-sized batch production. Purpose-built for left-hand turning and defined approach geometry Configured for left-hand cutting, this toolholder applies a 93° approach angle that positions the insert for robust cutting forces and controlled chip flow in left-handed operations. Left-hand orientation is essential when machining features that demand a specific feed direction or when machine setup requires mirrored toolpaths. The clear specification of direction and angle simplifies process planning and avoids ambiguity when integrating the holder into existing tool racks or CNC tool libraries. Integration with workshop procurement and quality assurance Produced by Teknik Makina to ISO-style designation SDJCL 1616, the holder is light at 0.18 kg yet engineered for industrial use. The compact form factor makes it easy to stock alongside other turning tools, and the standardised fastening parts reduce the variety of spare hardware required. For procurement, the product’s compatibility with commonly used DCMT inserts and standard screws simplifies logistics and keeps tooling inventories lean, supporting Metav’s approach to accessible precision. For tailored advice, spare-part lists or to procure Teknik Makina SDJCL 1616 clamping holders directly, contact Metav Werkzeuge — email info@metav-werkzeuge.com or call +49 2822 7131930 for prompt, specialist support and reliable supply from our Emmerich centre Technical data Article number: D157TM Designation: SDJC for DCMT Indexable Inserts Manufacturer: Teknik Makina Core dimensions Overall length: 100 mm Head width: 16 mm Shank height: 16 mm Cutting head width: 16 mm Cutting height: 25 mm Weight: 0.18 kg Cutting/approach angle: 93° Features & fittings ISO designation: SDJCL 1616 Compatible inserts: DCMT 11T3 Cutting direction: left-hand Clamp screw: M5 Torx screw: M3.5 x 8.5 Torx key size: T15 Clamping plate: TA030 FAQ Which inserts are compatible with this holder? The holder is compatible with DCMT 11T3 indexable inserts; the SDJCL 1616 is engineered to seat these inserts securely for standard turning tasks. Is the holder suitable for right-hand turning applications? This toolholder is configured for left-hand cutting and is intended for left-oriented turning operations rather than right-hand use. What are the main dimensions to consider when planning a tool setup? Key dimensions are 16 x 16 mm for head and shank, overall length 100 mm, and cutting height 25 mm for the SDJCL 1616 (SKU D157TM). What fastening parts are required for proper assembly? Assembly uses an M5 clamp screw, an additional M3.5 x 8.5 torx screw and a T15 torx key; the clamping plate specified is TA030. What advantage does the 93° cutting angle provide? The 93° approach angle provides a robust contact geometry that stabilises the insert under cutting loads, improving surface finish and component consistency. Manufacturer / Responsible: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of the combination of precise 12 × 12 mm shank geometry, secure TA030 clamping and DCMT 11T3 compatibility for consistent turning results; order via Metav Werkzeuge or consult the technical team for confirmation. SDJC for DCMT Indexable Inserts – SDJCL 1212 clamping holder, left-hand, 12 × 12 mm (Teknik Makina) The SDJC for DCMT Indexable Inserts is a left-hand clamping holder designed for secure, repeatable turning operations with DCMT 11T3 inserts in workshop and production environments Compatible with DCMT 11T3 inserts Left-hand cutting orientation 12 × 12 mm shank cross-section TA030 clamping plate with M5 screw Consistent clamping for accurate turning results The robust clamping holder design secures indexable inserts to provide stable cutting conditions and predictable part quality. Compatibility with DCMT 11T3 inserts allows the use of standard triangular-shaped turning tips, which simplifies inventory and reduces tooling change complexity. The 12 × 12 mm shank cross-section gives a compact footprint while maintaining sufficient rigidity for light to medium turning tasks. A cutting approach of 93° keeps cutting forces well directed, helping to reduce vibration and deliver repeatable surface finishes. Fast set-up and reliable insert retention Quick and safe insert changes are enabled by the integrated TA030 clamping plate and the designated screws. The clamping plate is retained with an M5 screw, while the insert seat is secured via a Torx fixing (M3.5×8.5) tightened with a T15 key, ensuring consistent torque and repeatability from one change to the next. This arrangement reduces downtime during routine maintenance and supports stable cutting geometry after each reassembly, which in production leads to fewer in-process adjustments and higher throughput. Compact length and light weight for adaptable toolposting With an overall length of 110 mm and a mass of 0.13 kg, this holder balances accessibility and low inertia for many lathe setups. The compact form factor eases access to tight workpiece features, while the modest weight reduces additional radial loading on the turret. The left-hand cutting orientation suits operations where negative-direction cuts are required or when specific toolpath strategies are in use. The holder is identified as SDJCL 1212, matching common ISO-style designations to simplify procurement and toolroom communication. Contact Metav Werkzeuge for tailored technical advice and to source the Teknik Cutting Tools SDJC for DCMT indexable inserts (SKU D156TM) for integration into existing tooling systems Technical data Article number: D156TM Manufacturer: Teknik Makina Product: SDJC for DCMT Indexable Inserts ISO designation: SDJCL 1212 Core data Shank width: 12 mm Shank height: 12 mm Cutting-head width: 12 mm Cutting height: 20 mm Overall length: 110 mm Weight: 0.13 kg Cutting angle: 93° Direction: left Special features Compatible inserts: DCMT 11T3 Clamping plate: TA030 Clamping plate screw: M5 Torx screw: M3.5×8.5 Torx key: T15 Holder designation: SDJCL 1212 FAQ Which insert types fit this holder? The SDJC for DCMT Indexable Inserts accepts DCMT 11T3 indexable tips, allowing the use of widely available turning inserts for general-purpose machining. Is the holder suitable for left-hand turning only? This toolholder is specified for left-hand cutting direction and is intended for operations that require a negative-direction approach. What are the key dimensions to verify for toolpost compatibility? Relevant dimensions include the 12 × 12 mm shank cross-section and 110 mm overall length; these determine fit in standard tool posts and turret pockets. How is the insert retained and what fastening is required? The insert is secured via the TA030 clamping plate; the plate is fixed with an M5 screw while the insert is clamped using a M3.5×8.5 Torx screw tightened with a T15 key. Can this holder be identified by an ISO-style code? Yes, the holder carries the designation SDJCL 1212, which aids in matching the part to tooling lists and ordering documentation. Manufacturer / Responsible: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of the compact SDJCR 1616’s precise 16 mm clamping geometry and secure Torx fixing to maintain stable, repeatable turning operations; order directly via Metav Werkzeuge or contact the consultants for suitability advice. SDJC for DCMT Indexable Inserts (SDJCR 1616) — Compact right‑hand toolholder with 93° approach angle A SDJC for DCMT indexable inserts (SDJCR 1616) designed for right‑hand turning tasks where a compact head and reliable clamping are essential for consistent chip control and repeatable part quality. SDJCR 1616 ISO toolholder for DCMT 11T3 inserts Compact 16 x 16 mm head for tight spaces Right‑hand cutting with 93° approach angle Includes Torx M3.5x8.5 screw and M5 clamp plate Stable clamping that prolongs insert life and reduces rework The holder’s 16 mm head dimensions and robust clamping geometry provide a rigid interface between tool and insert, which reduces vibration and improves surface finish. With an approach angle of 93°, the arrangement favours secure engagement of DCMT 11T3 indexable inserts and helps maintain consistent chip formation in interrupted cuts. The combination of compact size and structural stability translates into fewer insert changes and lower scrap rates in serial turning operations. Fast set‑up and positive locking for uninterrupted machining A clear benefit of this design is quick, repeatable assembly: the clamp plate (TA030) uses an M5 fastening and the insert pocket secures with a Torx M3.5x8.5 screw, tightened with a T15 key, which simplifies workshop logistics and reduces tool‑change time. At an overall length of 100 mm and weighing 0.18 kg, the toolholder is easy to handle yet substantial enough to withstand typical turning forces. These features support efficient production cycles and make the holder suitable for compact toolpost arrangements. Broad compatibility for common turning setups Engineered for standard indexable inserts, the holder accepts DCMT 11T3 inserts and pairs with bar designations such as H11‑F, enabling integration into many existing tool systems. The right‑hand cutting orientation suits conventional lathe programmes and tooling layouts, while the ISO designation SDJCR 1616 ensures clear specification when coordinating inserts and spare parts. This makes the component a practical choice for workshops aiming to consolidate tooling without compromising process reliability. Contact Metav Werkzeuge today to confirm fitment and secure reliable supply of the SDJCR 1616; information and ordering via info@metav-werkzeuge.com or by telephone on +49 2822 7131930 Technical data Article number: D458TM Manufacturer: Teknik Makina ISO designation: SDJCR 1616 ECLASS: 21181004 Facts Head width: 16 mm Head height: 16 mm Cutting head width: 16 mm Overall length: 100 mm Weight: 0.18 kg Approach angle: 93° Cutting direction: right Features Suitable for DCMT 11T3 inserts Clamp plate: TA030 Clamp plate screw: M5 Torx screw: M3.5x8.5 Torx key: T15 Boring bar designation: H11-F FAQ Which inserts fit this holder? The holder is specified for DCMT 11T3 indexable inserts and is designated SDJCR 1616, ensuring compatibility with common DCMT insert geometries. What is the approach angle and why does it matter? The 93° approach angle defines the cutting engagement and supports stable chip formation and consistent surface finish in right‑hand turning operations. Which fastening parts are supplied or required? The toolholder uses a clamp plate TA030 with an M5 fastening and requires a Torx M3.5x8.5 screw (Torx key T15) for insert retention. Is the holder suitable for compact toolposts? Yes; with a compact 16 x 16 mm head and 100 mm overall length, the design is intended for tight machining envelopes and minimal overhang. What is the ISO designation and catalogue reference? The ISO designation is SDJCR 1616 and the SKU / article number is D458TM. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a compact, robust clamping solution that combines precise insert positioning and space-saving dimensions for reliable external turning operations; order directly via Metav Werkzeuge or request tailored advice from the consultants. Clamping holder SDJC for DCMT indexable inserts — right-hand, flat style by Teknik Makina The SDJC for DCMT Indexable Inserts is a right-hand clamping holder designed for external turning with a flat head, optimised for DCMT 11T3 inserts in confined setups. Right-hand clamping holder SDJCR 1212 Flat head for DCMT 11T3 indexable inserts 12 × 12 mm head dimensions for compact turning 110 mm overall length, lightweight 0.134 kg Stable cutting performance for small-diameter turning The holder, designated SDJCR 1212, secures DCMT 11T3 indexable inserts in a low-profile mounting that reduces tool overhang and vibration. The flat head geometry, together with a defined 93° cutting angle, was engineered to maintain a repeatable cutting edge position, which is beneficial when machining short, external profiles. Precision is supported by the standardised ISO-style seat, so insert seating and indexing are consistent; this reduces set-up deviations and contributes to predictable tool life and part tolerances. Space-saving design that improves machining access With a head footprint of 12 mm by 12 mm and an overall length of 110 mm, the turning holder enables access in tight fixtures and close to shoulders where larger tools would obstruct the operation. The holder’s lightweight construction (0.134 kg) reduces dynamic loads on the turret during rapid direction changes, which helps to preserve surface finish. The right-hand orientation is matched to clockwise cutting applications and is suitable for many general-purpose turning tasks in job shops and production cells where compactness and rigidity are required. Compatibility and practical workshop advantages The unit accepts indexable inserts, permitting economical regrinds and rapid replacement without full tool change. The bar designation J11-F indicates the compatible shank system for insertion into common tool posts and turrets. As a standardised clamping solution, the component is compatible with established insert grades and chipbreaker geometries, allowing adaptation to a wide range of materials and cutting conditions while keeping inventory management straightforward. Reliability, supply and partner assurance Manufactured by Teknik Makina and distributed through Metav’s quality-controlled supply chain, the toolholder combines practical design with consistent availability for workshop planners. The standardised ISO-style identification and compact dimensions mean predictable integration into existing tooling setups, reducing planning time and improving machine uptime. For machining strategies where small turnings, close tolerances and repeatable insert location matter, this holder delivers measurable process stability. Contact Metav Werkzeuge for specification matching and delivery from Emmerich — telephone +49 2822 7131930 or e‑mail info@metav-werkzeuge.com for tailored advice and rapid dispatch. Technical Data Article number: D457TM Manufacturer: Teknik Makina Product: SDJC for DCMT Indexable Inserts SKU: D457TM ISO designation: SDJCR 1212 Compatible insert: DCMT 11T3 Cut direction: right eClass: 21181004 Facts Head width: 12 mm Head height: 12 mm Head cutting width: 12 mm Overall length: 110 mm Weight: 0.134 kg Cutting angle: 93° Special features Flat head design Right-hand clamping holder Bar designation J11-F Indexable insert compatibility Compact, low-profile construction FAQ What inserts fit this clamping holder? The clamping holder is specified for DCMT 11T3 indexable inserts and secures them via the SDJCR 1212 seat for standard seating and indexing. Is the holder right- or left-hand oriented? This toolholder is a right-hand design, intended for clockwise cutting directions in standard turning operations. What are the key dimensions to check for turret fitment? Critical dimensions are the 12 mm head width/height and 110 mm overall length; verify turret clearance and the J11-F bar designation for correct shank compatibility. Will the holder work in tight shoulder machining? Yes — the flat head and compact 12 × 12 mm footprint are intended to improve access in confined setups while maintaining a stable cutting position. Which manufacturer produces this toolholder and who supplies it? The toolholder is produced by Teknik Makina and supplied via Metav’s distribution, referenced under SKU D457TM for procurement and stock enquiries. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of precise clamping, a 25 mm cutting height and compatibility with DCMT 11T3 indexable inserts to ensure consistent turning performance; order directly via Metav Werkzeuge or consult our specialists for application guidance. SDHCL 2525 Clamping Holder (SDHC) – 25 mm cutting height, 150 mm overall length | Teknik Makina A robust SDHCL 2525 clamping holder engineered for left‑hand turning applications, designed to accept DCMT 11T3 indexable inserts and to provide secure, repeatable clamping in production environments Compatible with DCMT 11T3 inserts 25 mm cutting height for robust cuts 150 mm overall length for deep reach Left‑hand cutting direction, ISO SDHCL 2525 Reliable clamping and consistent tool performance The clamping system is built to deliver secure clamping and repeatable geometry across shift cycles. With a 25 mm cutting height and a plunge‑resistant clamping arrangement, the holder stabilises the insert during interrupted cuts and heavier feed rates. The specified 107.5° cutting angle is incorporated to balance cutting forces and chip flow, which reduces chatter and preserves tool life. These measurable design choices are intended to support efficient production and consistent component tolerances. Reach and rigidity for demanding turning tasks A 150 mm overall length combined with a 32 mm head width provides extended reach while maintaining rigidity for longer overhangs. The moderate mass of 0.738 kg contributes to vibration dampening without adding unnecessary inertia, and the left‑hand orientation is suited for machines or setups that require inverse cutting direction. Terms such as left‑hand cutting are standardised in workshop planning: left‑hand denotes the feed and orientation used during turning operations, not tool handedness alone. Standard interfaces and fast setup for production use ISO designation SDHCL 2525 identifies the clamping geometry and ensures compatibility with industry tooling systems. The holder accepts a clamping screw with an M11 interface, enabling straightforward replacement and torque control during maintenance. By using established indexable inserts such as DCMT 11T3, setup times are reduced and insert stocking is simplified, which supports predictable changeovers and sustained throughput on the shop floor. Contact Metav Werkzeuge for application advice and to order the SDHCL 2525 clamping holder from Teknik Cutting Tools — expert guidance is available by phone or email to confirm machine compatibility and insert selection Technical Data Article number: D352TM Manufacturer: Teknik Makina ISO designation: SDHCL 2525 Suitable for inserts: DCMT 11T3 Facts Cutting height: 25 mm Head width: 32 mm Holder width: 25 mm Overall length: 150 mm Cutting angle: 107.5° Weight: 0.738 kg Clamping screw: M11 Cutting direction: left Special features SDHC clamping type for indexable inserts Compatible with DCMT 11T3 indexable inserts ISO standardised holder geometry Designed for left‑hand turning operations FAQ Which inserts are compatible with this holder? The SDHCL 2525 clamping holder is compatible with DCMT 11T3 indexable inserts; the combination (Teknik Makina, SKU D352TM) is specified for this insert size and form. Is the holder suitable for left‑hand turning only? Yes, the unit is configured for left‑hand cutting direction, making it appropriate for operations and machines that require inverse feed orientation. What are the key dimensions to check for machine setup? Key dimensions are 25 mm cutting height, 150 mm overall length and 32 mm head width, which should be verified against toolpost clearance and turret capacity before fitting the holder. What clamping interface is used for the insert screw? The holder uses an M11 clamping screw interface to secure the insert, supporting standard torque settings and straightforward servicing. How does the design support stable turning with longer overhangs? With its 150 mm overall length and 0.738 kg mass, the holder balances reach and rigidity to reduce vibration during extended overhang operations, improving surface finish and repeatability. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Take advantage of a compact tooling solution that combines sturdy shank stability, standard indexable insert compatibility and precise T-slot cutting for reduced setup time. The design pairs a 63 mm cutting diameter with a 25 mm shank for reliable rigidity, while compatibility with common indexable inserts keeps consumable costs low — order or enquire via Metav Werkzeuge for tailored advice. T-Nut Cutter S072TM — T-slot cutter, 63 mm diameter, DCMT-compatible A robust T-slot cutter, T-Nut Cutter S072TM, built for producing precise T-nuts and grooves in milling operations with standard indexable inserts Precision T-slot cutting for repeatable fittings Compatible with DCMT 11T3 indexable inserts 63 mm diameter for deep, stable cuts 25 mm shank for rigid toolholding Increase throughput with a stable cutter geometry The cutter’s 63 mm diameter and stout 25 mm shank deliver a combination of rigidity and reach that reduces vibration and enables higher, more consistent feed rates. By improving mechanical stability during machining, the tool supports shorter cycle times and fewer rejected parts; this is an efficiency gain that directly translates into higher throughput for series production. The overall tool geometry is optimised for producing repeatable T-slots, so changeovers become faster and machining parameters stay more predictable. Lower tooling costs through standard insert compatibility Featuring support for DCMT 11T3 indexable inserts and geometries specified as 55° for DCMT and 35° for VBMT, the cutter uses widely available insert types to reduce inventory complexity. The use of common inserts means replacement is quick and inexpensive compared with bespoke solutions, and carbide insert options offer balanced wear performance. For operations seeking predictable tool-change procedures and minimal downtime, the insert system provides a practical cost-benefit while maintaining surface quality and slot accuracy. Designed for secure seating and simple maintenance With four cutting edges and a clear fastener pattern, the cutter ensures stable insert clamping and easy maintenance. The supplied fastening arrangement uses a Torx screw M3.5x9 and a T15 key, which standardises the tightening process and ensures repeatable clamping torque. This arrangement reduces the risk of insert movement under load and makes routine servicing straightforward on the shop floor. The overall construction and fastener choice support long-term repeatability without specialised tooling. Practical setup guidance and quality assurance The cutter’s 120 mm overall length and 40 mm cutting length make it suitable for a range of T-slot depths while retaining sufficient tooloverhang control. When pairing the cutter with suitable cutting parameters and a secure toolholder, the operator benefits from improved dimensional consistency and a cleaner surface finish. For best results, match the insert geometry to the material and machine capability; those seeking specific cutting data for unusual workpiece alloys or novel setups should consult the technical team at Metav Werkzeuge for application-specific guidance. For application advice or to discuss a tailored tooling package, contact Metav Werkzeuge — their specialists in precision tooling will assist with selection, compatible inserts and procurement from Emmerich. Technical data Article number: S072TM Manufacturer: Teknik Makina Item name: T-Nut Cutter Compatible inserts: DCMT 11T3 Insert angles: 55° for DCMT and 35° for VBMT Facts Diameter: 63 mm Cutting edges: 4 Overall length: 120 mm Shank diameter: 25 mm Cutting length: 40 mm Weight: 0.536 kg Cutting angle: 55° Special features For indexable inserts DCMT 11T3 Torx screw M3.5x9 Torx key T15 Designed for repeatable T-slot machining FAQ Which indexable inserts fit this cutter? The T-Nut Cutter S072TM accepts DCMT 11T3 indexable inserts and is dimensioned to work with those geometries for reliable T-slot profiling. How many cutting edges does the tool have and what is the effective cutting length? The tool features 4 cutting edges and an effective cutting length of 40 mm, giving a good balance between material removal and slot depth capability. What shank size is required for secure toolholding? A 25 mm shank is specified for the cutter; using a matched, high-rigidity toolholder improves repeatability and surface finish when machining T-slots. Which fastening components are needed for insert replacement? Insert clamping uses a Torx screw M3.5x9, tightened with a T15 key, ensuring consistent clamping torque and simple maintenance routines. Is the cutter suitable for deep T-slots or limited-access pockets? With a 63 mm diameter and 120 mm overall length, the cutter is suited to moderate-depth T-slots; for deeper or very narrow pockets, verify reach and clearance against the specific workpiece geometry Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of the combination of a compact 16 x 16 mm shank, secure clamping for DCMT 11T3 inserts and a short 100 mm overall length to keep turning operations consistent and flexible; order the SDACR‑F directly via Metav Werkzeuge or request application advice from our consultants. SDACR‑F clamping holder (SDACR 1616) – right‑hand external turning, Teknik Makina A SDACR‑F clamping holder designed for secure right‑hand external turning with DCMT indexable inserts, suitable for general workshop and light production use. SDACR 1616 shank 16 x 16 mm Compatible with DCMT 11T3 inserts Right‑hand orientation, 90° cutting angle 100 mm overall length, 0.2 kg weight Consistent chip control through precision clamping The SDACR‑F is engineered to deliver consistent clamping and predictable tool geometry when used with DCMT 11T3 indexable inserts. The SDACR 1616 designation reflects the holder’s nominal shank dimensions, which are 16 x 16 mm, guaranteeing a standardised fit in compatible toolposts and reducing variation between set‑ups. A defined 90° cutting angle ensures stable cutting forces during external turning, which helps maintain surface finish and dimensional repeatability across a production run. For workshop managers seeking dependable repeatability, this compact toolholder balances rigidity and accessibility without complicating tooling inventories. Built for quick set‑up and repeatable accuracy Mechanical simplicity is the main advantage of this design: the clamping interface secures inserts reliably while enabling straightforward index changes. The holder’s compact form and H11‑F shank designation simplify mounting and alignment, shortening machine downtime during tool changes. With a 100 mm overall length and a mass of 0.2 kg, the assembly imposes minimal overhang, which reduces vibration potential and supports consistent cutting conditions. Reduced set‑up time translates directly into higher machine availability, especially in small to medium lot production where frequent tool swaps are normal. Versatile compatibility for everyday turning tasks Designed for right‑hand cutting, the toolholder is geared towards external turning and general finishing operations in workshop and light industrial settings. Its compatibility with the widely used DCMT 11T3 insert format makes the holder a practical choice for operations that value inventory simplicity: a single holder supports multiple grades and geometries of inserts. The compact head and standardised shank dimensions assist in compact tooling arrangements and make the holder suitable for constrained toolpost environments where accessibility and clear sightlines are important. Supplier assurance and streamlined procurement Supplied under SKU D442TM, this holder is part of a pragmatic tooling strategy that emphasises interchangeability and reliable performance. Specifying a standardised clamping holder reduces the need for multiple bespoke solutions and simplifies purchasing and maintenance cycles. Metav’s selection process and distribution from Emmerich act as an added quality filter for European customers, supporting consistent availability and traceable sourcing. For procurement teams, the combination of technical conformity and supply reliability reduces the risk of unexpected process variation while keeping toolroom complexity manageable. Request technical advice from Metav Werkzeuge to confirm the SDACR‑F’s suitability for the intended turning process — contact Metav Werkzeuge at info@metav-werkzeuge.com or call +49 2822 7131930 for tailored recommendations. Technical data Article number: D442TM SKU: D442TM Model: SDACR‑F for DCMT Indexable Inserts ISO designation: SDACR 1616 Manufacturer: Teknik Makina Facts Shank size: 16 x 16 mm Head width: 16 mm Holder width: 16 mm Overall length: 100 mm Weight: 0.2 kg Cutting angle: 90° Special features Compatible inserts: DCMT 11T3 Orientation: right‑hand Shank designation: H11‑F Suitable for external turning applications Compact design for reduced overhang FAQ What insert type fits this holder? The SDACR‑F clamping holder is compatible with DCMT 11T3 indexable inserts. Is the holder right‑hand or left‑hand oriented? This toolholder is manufactured for right‑hand cutting and external turning operations. What are the shank dimensions of the holder? The holder uses a 16 x 16 mm shank (SDACR 1616 specification). How long is the toolholder and what is its weight? The overall length is 100 mm and the unit weight is 0.2 kg. How can this holder be ordered or referenced? Order using SKU D442TM; consult Metav Werkzeuge for technical clarification or procurement advice. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Combine robust clamping with through‑coolant efficiency and compact dimensions to secure repeatable turning results; the right‑hand SVJCR 2020 holder accepts standard indexable inserts and offers a 150 mm overall length with a 93° cut angle. Order the holder directly via Metav Werkzeuge or consult their technical advisors for application matching. Klemmhalter SVJCR 2020 — Right‑hand clamping holder with internal coolant, Teknik Makina The Klemmhalter SVJCR 2020 is a right‑hand clamping holder intended for turning operations, featuring internal coolant and designed to work with common DCMT 11T3 indexable inserts. Internal coolant channel for efficient chip evacuation Right‑hand orientation for standard turning operations Compatible with DCMT 11T3 indexable inserts Robust SVJCR 2020 clamping system, 150 mm overall length Repeatable clamping for reliable part quality The SVJCR 2020 designation identifies a precision clamping system that secures indexable inserts with consistent seating and repeatability. The SVJCR 2020 clamp geometry reduces insert movement under load, which translates into stable cutting conditions and more predictable tool life. The 93° approach angle ensures favourable cutting forces for many external turning applications, while the moderate mass (approximately 0.735 kg) keeps tool overhang manageable. These attributes together reduce scrap rates and support steady cycle times on serial production runs. Internal coolant to keep cycles productive An integrated internal coolant channel directs cutting fluid close to the cutting edge, improving chip control and cooling the insert‑seat interface. This targeted supply reduces heat build‑up, which often extends insert life and helps maintain surface finish quality over longer cuts. In practice, coolant‑through holders lower the need for secondary interventions to clear chips and can enable slightly higher cutting parameters where the machine and insert grades permit, improving overall machining throughput without sacrificing consistency. Workshop‑friendly dimensions and serviceability Compact dimensions have been chosen to balance rigidity and accessibility: overall length 150 mm, head width 32 mm, holder width/height 25 mm and a cutting height of 35 mm. These measures make the toolholder suitable for typical lathe toolposts while keeping every dimension within common fixture envelopes. Maintenance uses standard hardware (Torx key T8, screw M2.5x6.5), simplifying routine insert changes and clamp checks. The relatively low weight supports safer handling at the bench and reduces inertia during rapid tool changes. Designed for integration and dependable operation As a right‑hand turning holder, the component integrates into production settings where predictable orientation is required. The SVJCR 2020 clamping form and the compatibility with standard DCMT 11T3 inserts enable quick requalification when replacing worn cutters, which shortens downtime. Robust construction and a focus on practical features support a dependable supply chain relationship: tools delivered from an established partner help to keep machines cutting with minimal administrative overhead. Contact Metav Werkzeuge for application advice on the Teknik Makina SVJCR 2020 holder and to confirm compatibility with specific insert grades and machine setups Technical data SKU: AP521TM Designation: Klemmhalter (SVJCR 2020) Manufacturer: Teknik Makina Overall length: 150 mm Weight: 0.735 kg Cutting direction: right Internal cooling: yes Facts Head width: 32 mm Holder width: 25 mm Holder height: 25 mm Cutting height: 35 mm Cutting angle: 93° Torx key size: T8 Torx screw: M2.5x6.5 Special features ISO designation SVJCR 2020 Compatible inserts: DCMT 11T3 Right‑hand turning holder Through‑coolant provision for improved chip control FAQ Which indexable inserts fit this holder? The holder is designed for compatibility with DCMT 11T3 indexable inserts; confirm the chosen insert grade and geometry for intended materials before production. Is cooling delivered through the holder? Yes, the SVJCR 2020 toolholder features internal coolant to deliver fluid near the cutting edge and assist chip evacuation. What is the overall length and weight of the toolholder? The overall length is 150 mm and the weight is approximately 0.735 kg, making it suitable for standard lathe toolposts. What fastening hardware is required for maintenance? Maintenance and insert changes use a T8 Torx key and the clamp screw spec is M2.5x6.5, which are common workshop standards. Which cutting direction is this holder designed for? The product is configured for right‑hand turning operations and is intended for external turning applications. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

The combination of a rigid clamping concept, internal coolant feed and a defining 93° cutting angle ensures steady chip control and longer tool life in left-hand turning operations; order the holder directly via Metav Werkzeuge or request technical advice from the Metav team for fast supply. Klemmhalter SVJC for VCMT Indexable Inserts — left-hand toolholder with internal coolant, Teknik Makina The Klemmhalter SVJC for VCMT Indexable Inserts is a left-hand turning toolholder designed for industrial turning tasks, offering integrated coolant routing and a compact 150 mm form for stable machining with common triangular inserts. Left-hand cutting orientation Suitable for DCMT 11T3 inserts Internal coolant feed integrated Compact overall length 150 mm Solid construction, weight 0.735 kg Consistent clamping for repeatable turning results The holder is built around the SVJCR 1616 ISO design, providing a predictable shank geometry suited to workshop toolposts and turret fixtures. With a defined 93° cutting angle, the geometry supports reliable chip flow and repeatable contact conditions, which directly benefits process stability and surface finish. The precise clamping seat reduces insert movement under load, translating the holder’s mechanical properties into measurable improvements in tool life and component tolerances. Coolant-through design to reduce thermal wear and improve tool life An internal coolant channel is integrated to deliver cutting fluid close to the cutting edge, enhancing heat dissipation and chip evacuation during heavy or interrupted cuts. This targeted cooling lowers thermal loads on the insert, which often extends the effective runtime of carbide grades and supports consistent dimensional accuracy across longer batches. For shops prioritising cycle-time and tool cost per part, the coolant feed is a tangible advantage for productivity and process reliability. Industrial-grade fastening and maintenance features The toolholder’s maintenance concept focuses on quick, secure insert changes and uncomplicated upkeep: clamping is effected using a Torx screw (size M2.5x6.5) that requires a T8 key for tightening. The accessible fastening geometry shortens service times and reduces downtime during insert indexation. With a measured mass of 0.735 kg and an overall length of 150 mm, the component balances rigidity and manageable handling, making it suitable for medium-duty turning centres and lathe toolposts where dependable clamping stiffness is required. Designed for common triangular turning inserts and practical workshop use Compatibility with triangular inserts is signalled by the designation and the specified insert sizing; the holder is provided for DCMT 11T3 style inserts and follows established clamping standards, supporting straightforward integration into existing tooling setups. The left-hand orientation and compact head width (32 mm) make the holder a pragmatic choice for external turning and profiling where approach direction and tool clearance are decisive. The documented shank reference H11-IK supports consistent seating and interchangeability in standard toolholding systems. For technical purchase advice on the Teknik Makina SVJC holder or to arrange prompt delivery from Metav Werkzeuge in Emmerich, contact Metav Werkzeuge at info@metav-werkzeuge.com or call +49 2822 7131930 for detailed assistance and stock information Technical Data Article number: AP520TM Manufacturer: Teknik Makina ISO designation: SVJCR 1616 Intended insert: DCMT 11T3 Shank designation: H11-IK Facts Cutting direction: left Cutting angle: 93° Overall length: 150 mm Head width: 32 mm Holder height: 25 mm Cutting height: 35 mm Weight: 0.735 kg Special features Internal coolant feed: yes Torx screw: M2.5x6.5 Torx key size: T8 Compact design for confined setups Robust construction for industrial use FAQ Which inserts fit the holder? The holder is specified for DCMT 11T3 triangular inserts; the SVJC designation indicates a clamping geometry compatible with these common insert types. Is coolant-through capability available? Yes — the toolholder includes an internal coolant feed to deliver fluid close to the cutting edge for improved heat control and chip evacuation. What is the cutting direction of the toolholder? The toolholder is configured for left-hand cutting operations, suitable for turning tasks that require a left-hand approach. What fastening hardware is required for insert changes? Insert clamping uses a Torx screw (M2.5x6.5) and a T8 Torx key for secure and fast insert replacement. What are the key dimensions to check for machine compatibility? Important dimensions: overall length 150 mm, head width 32 mm, holder height 25 mm, cutting height 35 mm; the ISO designation SVJCR 1616 indicates the shank form. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Benefit from robust clamping, coolant-through capability and precise left-hand cutting geometry to maintain consistent turning performance and minimise rework. Combine stable insert support and an optimised 93° cutting angle for reliable chip control; order the SVJCL 2525 directly via Metav Werkzeuge or consult our specialists for application advice. SVJCL 2525 Clamping Holder — left-hand turning holder with internal coolant by Teknik Makina SVJCL 2525 Clamping Holder is a left-hand external turning tool holder engineered for VCMT/DCMT indexable inserts and coolant-through machining in metalworking lathes Left-hand turning orientation for opposed cuts Internal coolant for enhanced chip evacuation Compatible with VCMT and DCMT 11T3 inserts ISO designation SVJCL 2525, shank M16-IK Stable left-hand turning for predictable results The holder is designed to deliver stable clamping in left-hand operations, which is especially relevant for opposed turning and specialised fixture setups. With a 93° cutting angle and a 35 mm cutting height, the geometry has been selected to reduce cutting forces and to maintain insert seating under load. This results in fewer interruptions for retightening and a more consistent surface finish, helping workshops maintain throughput without sacrificing control. Secure insert fixation and broad compatibility A firm clamping system and standardised seating enable quick changeovers and repeatable positioning for VCMT and DCMT indexable inserts such as DCMT 11T3. The holder’s ISO designation SVJCL 2525 clarifies shank form and mounting dimensions, while the shank specification M16-IK fits common boring-bar set-ups. These features mean the toolholder is suitable for a wide range of external turning tasks, where repeatability and secure fixation reduce downtime and scrap. Coolant-through design that supports tool life The integrated internal coolant channel is routed to the cutting zone to improve chip evacuation and cooling, which in turn diminishes thermal load on the insert and workpiece. For operations with moderate to heavy material removal, targeted coolant delivery can extend insert life and maintain cutting-edge integrity. Maintenance is straightforward: the Torx fastener specification (T15 key, M3.5x11 screw) has been selected for common workshop tooling and simple access during insert changes. Practical dimensions and workshop integration At 150 mm overall length with a holder width and height of 25 mm and a cutting-head width of 32 mm, the unit balances rigidity and accessibility in confined toolposts. Weighing 0.735 kg, it provides the mass required for stability without excessive inertia when indexing or repositioning. The holder’s form factor is compatible with standard toolposts and enables a compact setup where space is limited, while retaining the rigidity needed for accurate external turning. Arrange a technical consultation with Metav Werkzeuge to specify the SVJCL 2525 clamping holder for left-hand turning applications or to verify compatibility with existing toolposts and inserts. Technical data SKU: AP536TM Manufacturer: Teknik Makina Designation: SVJC for VCMT indexable inserts (SVJCL 2525) Direction: left-hand Core measurements Overall length: 150 mm Holder width: 25 mm Holder height: 25 mm Cutting-head width: 32 mm Cutting height: 35 mm Cutting angle: 93° Weight: 0.735 kg Features and compatibility Compatible inserts: VCMT, DCMT 11T3 Internal coolant: yes U-plate: TA034 Torx key: T15 Torx screw: M3.5x11 Shank designation: M16-IK FAQ What inserts can be used with this clamping holder? The SVJCL 2525 clamping holder is compatible with common VCMT and DCMT indexable inserts, including DCMT 11T3 types. Is the holder suitable for coolant-through machining? Yes, the holder features internal coolant routing to the cutting zone to aid chip evacuation and tool life. Does this holder support left-hand turning only? The toolholder is configured for left-hand cutting direction and is intended for left-hand turning applications. What are the key dimensions to check for toolpost compatibility? Check the overall length (150 mm), holder width and height (both 25 mm) and the shank designation M16-IK for compatibility with the existing toolpost. Which fasteners are required for insert clamping and maintenance? Insert and clamping maintenance use a Torx T15 key and an M3.5x11 mounting screw as specified for the unit. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of the combination of internal coolant, solid carbide construction and precise compatibility with DCMT 11T3 inserts for reliable boring results and reduced downtime. Order the tool directly via Metav Werkzeuge or ask our consultants for application advice. Teknik Makina Boring Bar SDUC with Coolant, Ø25 mm, Solid Carbide The Boring Bar SDUC with Coolant is a right-hand, internally cooled bar designed for precision boring and turning operations with indexable inserts in CNC lathes and turning centres Internal coolant supply Compatible with DCMT 11T3 inserts Solid carbide construction Ø25 mm diameter, 250 mm overall length Precision and performance for demanding machining Manufactured from solid carbide, this boring bar delivers high rigidity and thermal stability for consistent bore geometry and longer tool life. The integrated internal coolant channel directs cutting fluid precisely to the cutting edge, improving chip evacuation and reducing heat at the cutting zone. With a cutting height of 13 mm and right-hand cutting orientation, the tool is engineered to maintain surface finish and dimensional accuracy during interrupted cuts and extended cycles. The combination of robust material and targeted coolant reduces the frequency of rework and supports higher metal removal rates while keeping vibration low. Compatibility that speeds setup and reduces downtime Designed for DCMT 11T3 indexable inserts, the holder accepts commonly used carbide grades and insert geometries for flexible application across batches. Secure clamping is achieved by the specified Torx T15 fastener and M3.5x8.5 screw, allowing quick insert changes and repeatable seating without specialised fixtures. The ISO designation E20S SDUCR 11 simplifies procurement and replacement planning in production environments. These features together cut fixture time and make routine maintenance straightforward, supporting efficient shift handovers and fast tool changes on multi-shift shop floors. Workshop integration and practical advantages With a nominal diameter of 25 mm, overall length of 250 mm and a shank diameter of 20 mm, the tool fits compact tool holders while providing adequate reach for medium-depth bores. The unit’s weight of 0.95 kg contributes to stable rotation and predictable dynamic behaviour on heavy or small spindles. Right-hand cutting direction is optimised for conventional turning set-ups; the internal coolant reduces reliance on external nozzles and helps avoid chip recutting. For manufacturers seeking a dependable, ready-to-fit boring solution, the combination of material choice, coolant delivery and standardised insert compatibility offers a clear performance and productivity advantage. Contact Metav Werkzeuge for a technical consultation on the Teknik Makina SDUC boring bar with internal coolant — reliable supply from Emmerich and short delivery times. Technical Data Article number: KE34TM Manufacturer: Teknik Makina ISO designation: E20S SDUCR 11 Facts Diameter: 25 mm Overall length: 250 mm Shank diameter: 20 mm Weight: 0.95 kg Cutting height: 13 mm Cutting direction: right Special features Material: Solid carbide Internal coolant: yes For indexable inserts: DCMT 11T3 Torx screw: M3.5x8.5 (T15) FAQ Is the bar suitable for standard DCMT 11T3 inserts? Yes. The Teknik Makina SDUC with Coolant is designed for DCMT 11T3 inserts and accepts common carbide grades for turning and boring operations. How is the coolant supplied to the cutting edge? Coolant is delivered through an internal channel; this internal coolant design focuses fluid flow at the insert edge to improve chip evacuation and cooling. What torque driver is required for insert clamping? Insert clamping and screw access are specified for a Torx T15 key and the screw size is M3.5x8.5, ensuring secure and repeatable clamping. Can this boring bar be used on compact CNC lathes? Yes. With a shank diameter of 20 mm, Ø25 mm body and 250 mm overall length, it fits many compact tool holders while providing sufficient reach for medium-depth bores. What does the ISO code E20S SDUCR 11 indicate? The ISO designation E20S SDUCR 11 identifies the holder’s size, geometry and mounting standard, simplifying matching with existing toolholder systems and spare-part ordering. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Benefit from a compact combination of internal coolant and left-hand cutting that stabilises internal turning and improves tool life; compatible with standard DCMT 11T3 inserts and available directly via Metav Werkzeuge or via consultant enquiry. Boring bar SDUC with Coolant (E20S SDUCL 11) — Internal coolant, left-hand cutting, 25 mm The Boring bar SDUC with Coolant is a left-hand indexable boring bar for precision internal turning and stable chip evacuation in production and workshop environments Internal coolant for stable chip evacuation Fits DCMT 11T3 indexable inserts Solid carbide construction for rigidity 25 mm diameter, 250 mm overall length Greater process stability through coolant-assisted cutting The combination of internal coolant and a left-hand cutting orientation delivers improved cooling at the cutting edge and more reliable chip control, which directly reduces the risk of recutting and extends insert life. Designed for use with DCMT 11T3 indexable inserts, the tool supports consistent bore quality over long production runs. The integrated coolant channel focuses cooling and lubrication exactly where it is needed, helping to maintain surface finish and reduce thermal distortion in long internal bores. Rigidity and repeatable accuracy from its construction Constructed from solid carbide, the bar provides high stiffness and vibration damping that contributes to repeatable bore geometry and longer run lengths between rework. The 20 mm shank offers secure clamping in standard toolholders, while the 13 mm cutting height gives reliable insert support for stable cutting conditions. Fastening and insert retention use a T15 Torx drive with an M3.5x8.5 screw, ensuring a secure fit and straightforward, repeatable insert changes. The overall mass (approx. 0.95 kg) aids steadiness during plunge and overhang operations. Faster setup and predictable maintenance for production A focus on compatibility with widely used indexable inserts simplifies tooling logistics and reduces inventory complexity, allowing faster setup and predictable maintenance cycles. The 25 mm diameter and 250 mm overall length balance reach with rigidity, making the bar suitable for through-bore work and shorter internal features alike. Standardised clamping and screw sizes support quick insert replacement, minimising downtime and contributing to higher overall equipment effectiveness in both small workshops and larger machining centres. Contact Metav Werkzeuge for tailored advice on Teknik Makina boring bars and to secure the SDUC with internal coolant — phone +49 2822 7131930 or email info@metav-werkzeuge.com Technical data Article number: KE44TM Brand: Teknik Makina ISO designation: E20S SDUCL 11 Product name: Boring bar SDUC with Coolant Facts Diameter: 25 mm Overall length: 250 mm Shank diameter: 20 mm Weight: 0.95 kg Cutting height: 13 mm Special features Solid carbide Internal coolant Compatible with DCMT 11T3 inserts Left-hand cutting direction Torx key: T15 Torx screw: M3,5x8,5 FAQ Which indexable inserts fit this boring bar? The boring bar accepts DCMT 11T3 indexable inserts; use the manufacturer-recommended grades for the intended material and cutting conditions. Is coolant supplied through the bar? Yes — the E20S SDUCL 11 design includes internal coolant, which delivers lubrication and cooling directly to the cutting edge. What is the cutting direction of the tool? This tool features a left-hand cutting orientation suitable for left-hand internal turning operations. What are the fastening specifications for the insert? Insert retention uses a T15 Torx drive with an M3.5x8.5 screw for secure clamping and repeatable insert changes. What is the SKU and ISO designation for ordering and documentation? SKU KE44TM, ISO designation E20S SDUCL 11, produced by Teknik Makina Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Combine precise indexable-insert compatibility with compact dimensions and robust clamping to achieve repeatable turning results and shortened setup times. Order the Teknik Makina SDHCL 2020 clamp holder via Metav Werkzeuge or consult our specialists for application-specific recommendations. Clamp holder SDHCL 2020 (SDHC for DCMT indexable inserts) — left-hand, 125 mm overall length The clamp holder SDHCL 2020 is a left-hand toolholder engineered for external turning with DCMT 11T3 indexable inserts in workshop and light production environments. SDHCL 2020 ISO designation For DCMT 11T3 indexable inserts Left-hand orientation, 107.5° cutting angle Compact 125 mm overall length Consistent part quality through secure clamping The principal advantage of this toolholder is its robust clamping design, which secures DCMT 11T3 inserts reliably and reduces insert movement under cutting forces. The combination of a deliberate clamp geometry and the ISO designation SDHCL 2020 makes inspections and replacements straightforward, promoting consistent part tolerance and fewer scrapped components. This results in measurable improvements in first-pass yield and less time spent reworking components. Space-saving dimensions for improved access With a 125 mm overall length and a narrow 20 mm width, the holder provides access to tight diameters and close shoulder work without compromising stiffness. The 25 mm cutting head width and 25 mm cutting height support a compact footprint while maintaining an effective contact area for the insert. Workshops benefit from a reduced tool overhang and improved chip flow, which together enhance tool life and machining stability on small to medium workpieces. Designed for straightforward shop-floor integration The holder’s left-hand orientation and a precise 107.5° cutting angle are suited to conventional turning setups where left-handed approach angles are required. The shank designation K11 ensures compatibility with common tooling fixtures, simplifying inventory management. At 0.411 kg, the component is light enough for fast changeovers yet engineered to deliver the rigidity expected in production runs. These attributes combine to shorten setup times and reduce the number of special adapters required. Practical benefits for procurement and production planning Adopting this clamp holder reduces the variety of specialised holders needed, since it accepts a widely used insert format and conforms to an ISO-style designation. Fewer tool variants mean lower logistical overhead and faster tool changes at the turret. The technical data support straightforward procurement choices and ensure that purchasing decisions are based on measurable parameters rather than approximations. For procurement or technical clarification regarding the Teknik Makina SDHCL 2020 clamp holder, contact Metav Werkzeuge in Emmerich at +49 2822 7131930 or info@metav-werkzeuge.com for expert guidance and delivery options. Technical data Article number: D350TM Manufacturer: Teknik Makina Product: SDHC for DCMT Indexable Inserts ISO designation: SDHCL 2020 Facts Height: 20 mm Cutting head width: 25 mm Width: 20 mm Cutting height: 25 mm Overall length: 125 mm Weight: 0.411 kg Cutting angle: 107.5° Suitable insert: DCMT 11T3 Cutting direction: left Special features Shank designation: K11 ISO designation: SDHCL 2020 For DCMT 11T3 indexable inserts Left-hand turning orientation FAQ Which insert type fits this holder? The holder accepts DCMT 11T3 indexable inserts; compatibility is stated for the SDHCL 2020 clamp holder (Teknik Makina, SKU D350TM). Is the toolholder suitable for left-hand turning only? Yes. The design is specified for left-hand cutting direction and the geometry is optimised for left-hand operations. What are the key dimensions to check for turret mounting? Important dimensions include the 125 mm overall length, 20 mm width, and 20 mm height; these determine clearance and fixture compatibility for the workshop turret. How does the clamp holder support repeatable setups? The clamp geometry and ISO-style designation ensure repeatable seating of DCMT 11T3 inserts, reducing variation between tool changes and improving process reliability. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a compact, right-hand turning solution with DCMT 11T3 compatibility and a 90° cutting angle for reliable, repeatable machining; the holder’s 20 mm head dimensions and 125 mm overall length ensure easy integration into existing setups. Order or request advice directly via Metav Werkzeuge for assured supply and technical support. Clamping holder SDACR-F for DCMT indexable inserts (right-hand) – Teknik Makina A robust SDACR-F clamping holder designed for right-hand turning with DCMT 11T3 indexable inserts, suitable for workshop and production turning tasks. Right-hand turning, 90° cutting angle Compatible with DCMT 11T3 indexable inserts ISO designation SDACR 2020 20 mm head height and 125 mm overall length Consistent cutting results through rigid clamping and geometry The holder’s design delivers rigid clamping and stable tool presentation, which reduces chatter and improves surface finish during turning operations. With a 90° cutting angle and accommodation for DCMT 11T3 inserts the tool promotes predictable chip formation and repeatable toolpaths, translating into fewer scrapped parts and reduced rework. The arrangement is particularly beneficial when consistent axial positioning and reliable insert seating are required for batch production or precision jobbing. Simple compatibility for fast tool changes and setup Designed to the ISO SDACR 2020 shank standard, the clamping solution integrates smoothly with conventional toolposts and boring-bar systems identified as K11-F. The standardised interface enables quick mounting and exchange of indexable inserts, so changeovers are faster and machine downtime is reduced. At a weight of 0.397 kg and a compact 125 mm overall length, the unit balances rigidity with manageable mass for routine workshop handling. Economical tooling and suitability for mixed workshops By accepting replaceable indexable inserts, the holder reduces consumable costs compared with solid-tool alternatives: only the cutting edge is replaced while the main body remains in service. The compact dimensions—20 mm head height and 20 mm widths—make it suitable for confined setups where space and access matter, while the right-hand orientation supports standard turning directions. This combination of economy, straightforward maintenance and compact form factor suits both small specialist workshops and larger production environments seeking consistent turning performance. For precision right-hand turning solutions from Teknik Makina, rely on the SDACR-F clamping holder—contact Metav Werkzeuge for product availability and technical advice at info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: D444TM Product name: SDACR-F for DCMT Indexable Inserts Model designation: SDACR 2020 Brand: Teknik Makina Weight: 0.397 kg Dimensions & core data Head height: 20 mm Head width: 20 mm Shank width: 20 mm Overall length: 125 mm Cutting angle: 90° Cutting direction: right Compatibility & special features For DCMT 11T3 indexable inserts ISO designation SDACR 2020 Boring bar designation: K11-F Right-hand turning tool FAQ Which inserts fit the clamping holder? The SDACR-F clamping holder is designed for DCMT 11T3 indexable inserts and secures them for standard turning operations. Is the holder suitable for left-hand turning? This holder is configured for right-hand turning with a 90° cutting angle; left-hand operations require a corresponding left-hand tool variant. What does ISO SDACR 2020 mean for mounting? ISO SDACR 2020 denotes the shank and head geometry standard, ensuring compatibility with toolposts and holders designed for that format. Can the holder be used in small jobbing shops? Yes, the compact 125 mm overall length and modest weight make the holder practical for both small workshops and larger production environments. How does the design help reduce tooling costs? By using replaceable indexable inserts, only the cutting edges are renewed when worn, extending the service life of the holder and lowering per-edge costs. Manufacturer / Responsible: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a compact combination of secure clamping, internal coolant and precise geometry to keep turning processes consistent and predictable; request a tailored quote via Metav Werkzeuge for fast supply and expert advice. Clamping holder SVJCL 2020 – SVJC holder for VCMT/DCMT indexable inserts, left-hand, internal coolant (Teknik Makina) A robust clamping holder engineered for left-hand turning operations with VCMT/DCMT indexable inserts, designed to deliver stable tool engagement and coolant-fed machining in small- to medium-sized lathes. SVJCL 2020 design for secure insert clamping Internal coolant for improved chip evacuation Compatible with DCMT 11T3 and VCMT inserts 32 mm cutting head width for stable cutting Consistent clamping that reduces tool downtime The SVJCL 2020-style clamping holder provides a mechanically secure seat for indexable inserts, reducing micro-movement during heavy engagement. The combination of a solid clamping geometry and the specified M2.5x6.5 Torx screw (driven with a T8 key) ensures repeatable seating force and predictable tool life. For production environments where tool-change frequency affects throughput, this configuration supports longer, stable cutting intervals and a lower risk of insert chipping, which in turn reduces unplanned stoppages. Coolant-fed chip control for cleaner cuts Built with internal coolant, the holder channels cutting fluid directly to the insert pocket and cutting edge to assist chip evacuation and edge cooling. This feature improves surface finish and helps control thermal loading on both insert and workpiece during continuous turning. When paired with appropriate inserts such as DCMT 11T3, coolant-fed turning often yields a steadier process window and better control over built-up edge formation, particularly in alloyed steels and mixed materials. Geometry tuned for accurate turning performance A near-neutral 93° cutting angle and a 32 mm cutting head width give a balanced engagement that is suitable for facing and general turning tasks. The holder’s dimensions — holder height 25 mm, holder width 25 mm and cutting height 35 mm — are selected to match common toolpost and turret interfaces while providing the rigidity required for consistent cutting forces. This mechanical stability supports predictable chip formation and repeatable part tolerances when used in standard lathe setups. Straightforward fitment and machine integration With an overall length of 150 mm and a clear ISO designation SVJCL 2020, the holder integrates easily into existing tool posts and bar setups; the mounting bar reference K11-IK is supplied for compatibility checks. The unit’s weight of 0.735 kg is balanced for manual handling yet sturdy enough to resist vibration in moderate cutting regimes. Compatibility with VCMT/DCMT insert formats simplifies inventory management and tooling standardisation across multiple machines. Request a technical consultation or quote from Metav Werkzeuge for the Teknik Cutting Tools SVJCL 2020 clamping holder (AP531TM) to confirm fitment and delivery from Emmerich — contact info@metav-werkzeuge.com or call +49 2822 7131930 for prompt assistance Technical Data Article number: AP531TM Manufacturer: Teknik Makina Numbers / Core technical data Overall length: 150 mm Weight: 0.735 kg Cutting head width: 32 mm Holder height: 25 mm Holder width: 25 mm Cutting height: 35 mm Cutting angle: 93° Torx key: T8 Torx screw: M2.5x6.5 SKU: AP531TM Design & Features Left-hand orientation Internal coolant Compatible with DCMT 11T3 and VCMT inserts ISO designation: SVJCL 2020 Mounting bar designation: K11-IK FAQ Which insert types fit this holder? The holder is designed for DCMT 11T3-format inserts and is compatible with VCMT indexable inserts when specified; the SVJCL 2020 clamping geometry secures these insert formats for standard turning tasks. Does the holder provide coolant directly to the cutting edge? Yes, internal coolant is integrated into the clamping assembly so that fluid reaches the insert pocket and cutting edge, improving chip control and edge life. Is this a left-hand or right-hand holder? This toolholder is a left-hand orientation, intended for operations where the cutting direction is left-hand relative to the workpiece rotation. What fastener and key are required for the clamping screw? Clamping is achieved with a Torx screw M2.5x6.5, driven with a T8 Torx key as specified in the technical data. How does the 93° cutting angle affect machining? The 93° approach provides a near-neutral engagement that balances radial and axial loads, making the holder suitable for facing and general turning with stable force distribution. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Benefit from a robust T‑slot milling solution that combines compatibility with DCMT 11T3 indexable inserts, a 50 mm cutter diameter and a 25 mm shaft for secure mounting and consistent results. Order the tool directly via Metav Werkzeuge or contact the specialists for integration advice. T-Nut Cutter S070TM — 55° / 35° insert angles, 50 mm diameter (Teknik Makina) The T-Nut Cutter S070TM is a precision milling head for producing T-slots and grooves in steel components, engineered for use with DCMT and VBMT indexable inserts and designed for stable, repeatable machining. Compatible with DCMT 11T3 indexable inserts 50 mm diameter for deep T-slots Shaft diameter 25 mm for secure mounting Three cutting edges for smooth material removal Stable mounting for repeatable machining results The S070TM is built to reduce vibration and runout through a balanced geometry and a shaft diameter 25 mm that secures the toolholder interface. A stable mounting improves surface finish and tool life, which leads to more predictable cycle times in serial production. The 50 mm diameter and the cutter’s mass distribution contribute to steadier cutting forces, while the three cutting edges ensure continuous material engagement for a uniform chip flow and reduced rework. Flexible insert choices lower tooling costs Compatibility with indexable inserts such as DCMT 11T3 (and similar VBMT types) means insert tips are replaced rather than the whole head, reducing consumable costs and downtime. The tool supports a 55° approach geometry for DCMT and 35° for VBMT, which allows adjustment of cutting angle to match specific slot profiles and material behaviours. For operations where tool change frequency and inventory efficiency matter, this design facilitates standardised insert stocking and straightforward tip indexing. Geometry and lengths optimised for steel machining Designed for high-class steel machining, the cutter offers a cutting length 40 mm and a total length 120 mm, enabling deep T-slot creation without compromising stability. The cutter’s geometry balances clearance and support to deliver clean slot walls and consistent dimensions, even in tougher steel grades. Clearances and chip evacuation characteristics are tuned to reduce heat buildup, which extends insert life and maintains dimensional accuracy across longer runs. Quick assembly and straightforward maintenance Maintenance is uncomplicated thanks to the standard fastening hardware and accessible insert clamp. The cutter uses an M3.5x9 Torx screw secured with a T15 Torx key, enabling rapid insert changes and consistent torque during reassembly. This practical maintenance approach keeps machine downtime to a minimum and helps maintain cutting performance. Weight and handling were considered in the design—at approximately 0.584 kg the tool is heavy enough for stability yet light enough for safe handling during setup. For reliable T-slot production with proven insert compatibility, request the Teknik Makina T‑Nut Cutter S070TM through Metav Werkzeuge; our technical team is available at info@metav-werkzeuge.com or by phone on +49 2822 7131930 to assist with specifications and order placement. Technical data Article number: S070TM Manufacturer: Teknik Makina Product: T‑Nut Cutter — 55° for DCMT and 35° for VBMT indexable inserts Dimensions & core data Cutter diameter: 50 mm Shaft diameter: 25 mm Cutting length: 40 mm Total length: 120 mm Number of cutting edges: 3 Weight: 0.584 kg Features & compatibility Compatible inserts: DCMT 11T3 Cutting angles: 55° / 35° Torx screw: M3.5x9 Torx key: T15 Application note: suitable for high‑class steel machining FAQ What inserts are compatible with this T‑Slot cutter? The cutter accepts DCMT 11T3 indexable inserts and can also be used with equivalent VBMT styles; the S070TM design supports the specified insert seat and clamping arrangement. Which cutting angles are provided and what do they mean? The tool is designed for 55° geometry for DCMT inserts and 35° for VBMT inserts; these angles refer to the insert rake/approach and determine chip flow and slot profile suitability. How long are the cutting and overall lengths? This T‑nut cutter features a cutting length of 40 mm and a total length of 120 mm, permitting deeper slotting while maintaining rigidity. What fastening hardware is required for insert changes? Insert clamping uses an M3.5x9 Torx screw, tightened or released with a T15 Torx key, allowing rapid and repeatable insert replacement. Is the cutter suitable for steel machining? Yes — the S070TM is specified for high‑class steel machining, with geometry and chip evacuation suited to demanding steel applications. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Take advantage of a compact, coolant-fed turning solution that combines secure clamping, simple setup and consistent chip control for smoother production runs; order directly via Metav Werkzeuge or consult our specialists for application advice. Klemmhalter SVJCL 1616 — SVJC for VCMT / DCMT indexable inserts, right-hand, coolant-fed The Klemmhalter SVJCL 1616 is a right-hand turning holder designed for VCMT and DCMT style indexable inserts, offering a coolant-fed clamping arrangement for reliable chip evacuation in industrial turning operations. Right-hand turning holder with coolant feed Compatible with DCMT 11T3 / VCMT inserts Overall length 150 mm, compact design Torx screw M2.5x6.5 and T8 key for secure clamping Solid clamping and precise positioning for consistent machining A robust clamping concept ensures the insert remains stable under cutting forces: the SVJCL 1616 is engineered with a defined cutting geometry and a 93° approach angle that promotes predictable tool behaviour. With a cutting height of 35 mm and a compact head width of 32 mm, the holder keeps the insert datum close to the workpiece for repeatable results. The measured mass of 0.735 kg gives the assembly inertia that helps resist vibration without adding unnecessary bulk, supporting higher process stability on conventional and CNC lathes alike. Coolant-fed seat for better chip control and tool life Internal coolant is integrated into the clamping body to direct coolant towards the cutting zone, improving chip evacuation and reducing heat build-up at the cutting edge. The internal coolant provision reduces thermal load on the insert and can extend edge life in medium-duty turning cycles; it also helps maintain surface integrity by flushing chips away from the tool-workpiece interface. For workshops aiming for steady cycle times and fewer unscheduled indexings, the coolant-fed arrangement is a practical efficiency measure. Fast setup and secure fastening for reduced downtime Maintenance and index changes are simplified by the clear fastener specification: the clamping screw is M2.5x6.5 and is tightened with a Torx T8 key, a widely available combination in production environments. The ISO designation SVJCL 1616 and the corresponding shank notation H11-IK make toolholding identification straightforward during setup and reordering. The compact overall length of 150 mm shortens overhang, while the 25 mm body height and 25 mm body width keep the holder easy to clamp in many turret and tooling block geometries. Application focus: turning with indexable inserts This holder is tailored for turning operations using triangular indexable inserts such as DCMT 11T3 and equivalent VCMT shapes, offering a practical solution for facing and light to medium external turning passes when used in a right-hand orientation. The toolholder’s geometry and coolant capability support a variety of workshop tasks where repeatability and chip management are priorities. For integrators and production managers, the holder represents a small, well-defined component that fits into broader tooling strategies without overstating capability. For application advice or to secure supply of the Teknik Makina SVJCL 1616, contact Metav Werkzeuge in Emmerich by phone at +49 2822 7131930 or by email at info@metav-werkzeuge.com — technical consultation and rapid delivery options are available Technical data Article number: AP530TM Manufacturer: Teknik Makina Facts Overall length: 150 mm Weight: 0.735 kg Cutting height: 35 mm Holder height: 25 mm Holder width: 25 mm Cutting head width: 32 mm Cutting angle: 93° Special features Internal coolant: yes Compatible inserts: DCMT 11T3 / VCMT ISO designation: SVJCL 1616 Shank designation: H11-IK Cutting direction: right Screw: M2.5x6.5 Torx key: T8 SKU: AP530TM FAQ Which insert types are compatible with this turning holder? The turning holder accepts triangular indexable inserts in the DCMT 11T3/VCMT family; the clamping geometry is matched to those insert sizes for secure seating and repeatable positioning. Does the toolholder provide coolant to the cutting edge? Yes, the holder features internal coolant supply directed towards the insert seat to improve chip flushing and thermal control during operation. What fastener and key are required for insert clamping? Clamping is achieved with an M2.5x6.5 screw tightened using a Torx T8 key, ensuring a secure and serviceable assembly. Is this holder suitable for left-hand turning? This model is specified for right-hand cutting direction; select the corresponding left-hand version if left-hand machining is required. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Data conflict detected for SKU KE50TM: the field 'fur_wendeplatten' specifies DCMT 0702, while the product title and description reference DCMT 11T3. These specifications are inconsistent and must be verified before a product description can be produced. Please confirm the correct insert designation to ensure accuracy and consistency in the product listing, as discrepancies like this can lead to confusion for customers and potential errors in inventory management or order fulfilment. It is essential to address this issue promptly by cross-referencing the provided data with the manufacturer's specifications or consulting relevant documentation to determine the accurate and intended insert designation for this SKU.

Take advantage of the combination of robust shank design, precise insert compatibility and efficient chip evacuation for reliable T-slot machining; order the cutter directly via Metav Werkzeuge or consult the technical team for suitability. T-Nut Cutter TKC251TM — 60 mm diameter, 25 mm shank | Teknik Makina The T-Nut Cutter TKC251TM is a high-capacity T-slot cutter designed for producing secure T-nut profiles in metalworking and fixture production. High-efficiency 60 mm cutting diameter 4 cutting edges for smooth material removal 25 mm shank for solid clamping stability Precision and stability for consistent T-slot profiles The TKC251TM is engineered to deliver a consistent T-slot geometry thanks to its 60 mm diameter and stable 25 mm shank. The cutter’s 4 flutes promote balanced cutting forces and help to reduce chatter, while the specified cutting angle 55° supports accurate sidewall formation. These design choices combine to reduce rework and ensure repeatable part quality, particularly where secure fastening or locating elements depend on uniform T-nut dimensions. Weight and balance are tuned to support steady spindle performance; the tool mass of 0.583 kg contributes to vibration damping without compromising responsiveness. Fast insert changes and clarified insert compatibility This T-slot cutter accepts DCMT 11T3 indexable inserts, a common and versatile geometry for side-and-face operations. The indexable system allows worn cutting edges to be rotated or replaced rapidly, reducing downtime compared with brazed-tip tools. Fixing is secured by a M3.5x9 Torx screw and tightened with a T15 key, enabling repeatable clamp torque and straightforward servicing at the bench. For users unfamiliar with insert codes: DCMT 11T3 denotes an indexable, trigon-shaped insert with a nominal size suitable for the cutter’s pocket; the set-up supports precise chip breaking and economical edge indexing. Efficient machining workflow and workshop advantages With an overall length 120 mm and a cutting length 35 mm on the shaft, this cutter is configured for deep, stable engagement in common T-slot operations. The combination of robust shank diameter and multiple cutting edges contributes to improved surface finish and faster feed rates under suitable machine conditions. The cutter’s geometry is intended to provide a balance between material removal rate and tool life, supporting efficient batch production without sacrificing profile accuracy. Supplied technical data and the tool’s indexable insert system make it practical to plan replacement cycles and maintenance in a production schedule, helping workshops maintain throughput and predictable quality. Contact Metav Werkzeuge in Emmerich for procurement advice and accurate specification matching for the Teknik Makina T-slot cutter TKC251TM (SKU TKC251TM) Technical data SKU: TKC251TM Manufacturer: Teknik Makina Compatible inserts: DCMT 11T3 Core dimensions Diameter: 60 mm Overall length: 120 mm Shank diameter: 25 mm Cutting length (shaft): 35 mm Number of flutes: 4 Weight: 0.583 kg Cutting angle: 55° Design & compatibility Torx key: T15 Torx screw: M3.5x9 Files available: IDs 62de7eec33927e49dbf32794, 62de7e5c0f56dbb4de4dbf10 FAQ What inserts fit this T-slot cutter? The cutter uses DCMT 11T3 indexable inserts; these are compatible with the cutter’s insert pocket and support economical edge indexing. Can the cutter be clamped in a standard 25 mm toolholder? The tool features a 25 mm shank, which is intended for secure clamping in holders or collets rated for that diameter. What is the significance of the 4 flutes on this cutter? Four cutting edges distribute cutting forces evenly, improving surface finish and reducing vibration during T-slot machining. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

The combination of a secure clamp system and internal coolant ensures stable, long‑running left‑hand turning operations with consistent surface finish. Benefit from compatibility with DCMT/VCMT indexable inserts and robust geometry to reduce vibration and tool change time — order the holder directly via Metav Werkzeuge or request technical advice from our consultants. SVJCL 2020 clamping toolholder (SVJC for VCMT indexable inserts) — left‑hand with internal coolant The SVJCL 2020 clamping toolholder is a left‑hand turning tool designed for VCMT/DCMT indexable inserts, delivering secure clamping and integrated coolant for machining centres and conventional lathes. Left‑hand turning orientation (left) Internal coolant channel for reliable chip clearance Fits DCMT/VCMT indexable inserts Overall length 150 mm, robust 0.735 kg Stable performance for left‑hand turning and repeatable results Engineered for precision turning, this clamp‑style toolholder provides a defined cutting angle of 93°, which positions the insert for controlled chip formation and consistent contact pressure. The holder accepts standard DCMT/VCMT indexable inserts, enabling quick index changes and familiar insert geometry for toolrooms and production lines. Reduced setup time and repeatability are the primary benefits: repeatable seating and clamping lower scrap rates and shorten machine downtime, while established insert formats keep tooling logistics simple. Integrated coolant and secure clamping for longer insert life The internal coolant channel improves cooling at the cutting edge, supporting longer cutting intervals and more predictable tool wear. With the dedicated clamping plate TA034 and the supplied fastening hardware (Torx screw M3.5x11, Torx key T15), the insert is held firmly to minimise micro‑movement under load. This combination reduces thermal softening and edge chipping, which in turn increases productive cutting time and helps maintain surface quality on turned components — a direct economic advantage on medium‑ to high‑volume batches. Robust dimensions that enhance rigidity and reduce vibration With an overall length of 150 mm and a weight of 0.735 kg, the toolholder balances reach and rigidity for stable turning operations. Key dimensions such as a cutting height of 35 mm, a holder height of 25 mm, and a cutting‑head width of 32 mm contribute to a low‑vibration setup that supports better surface finish and longer insert life. The shank designation K16‑IK indicates the mounting profile, making integration into existing toolposts straightforward and ensuring secure support during heavy cuts. For technical consultation on integrating the SVJCL 2020 into existing setups or to request a quote, contact Metav Werkzeuge in Emmerich by e‑mail at info@metav-werkzeuge.com or by phone at +49 2822 7131930 — our specialists will advise on suitability and supply options Technical data Article number: AP535TM Manufacturer: Teknik Makina ISO designation: SVJCL 2020 Product type: SVJC for VCMT indexable inserts Facts Overall length: 150 mm Cutting height: 35 mm Holder height: 25 mm Cutting head width: 32 mm Holder width: 25 mm Weight: 0.735 kg Cutting angle: 93° ECLASS: 21181004 Special features Internal coolant: yes Fits inserts: DCMT 11T3 / VCMT Clamping plate: TA034 Torx screw: M3.5x11 Torx key: T15 Shank designation: K16‑IK Cutting direction: left FAQ Is this holder suitable for standard DCMT and VCMT inserts? The SVJCL 2020 holder is specified for DCMT 11T3 and compatible VCMT indexable inserts, enabling use of common turning inserts in production and repair workshops (AP535TM). Does the toolholder provide coolant to the insert tip? Yes — the holder includes an internal coolant channel, delivering coolant towards the insert to improve tool life and surface finish during sustained turning operations. What mounting or fastening parts are supplied? The holder is supplied with the designated clamping plate TA034 and uses a Torx screw M3.5x11 (Torx key T15) for secure retention of the insert seat. Can this holder be mounted in a standard toolpost with a K16 profile? The shank designation K16‑IK indicates compatibility with toolposts and boring bars accepting that profile; the holder offers straightforward integration where the K16 mounting is used. Is the SVJCL 2020 suitable for heavy roughing cuts? The toolholder’s robust geometry, defined cutting height and mass (0.735 kg) give it good rigidity for many turning tasks; assessment for heavy roughing should consider the machine power, insert grade and cutting parameters. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Optimise internal boring with a left‑hand, solid carbide bar that combines internal coolant and compatibility with DCMT 11T3 indexable inserts; the robust 16 mm shank and 200 mm overall length ensure stable set‑up and repeatable bore finishes — order the boring bar directly via Metav Werkzeuge or ask our consultants if needed Boring bar SDQC with Coolant — solid carbide, internal coolant, left‑hand Boring bar SDQC with Coolant is a left‑hand indexable boring bar designed for precision internal turning and reliable chip control in machine lathe and CNC applications Internal coolant for improved chip evacuation Solid carbide body for high rigidity Compatible with DCMT 11T3 indexable inserts 16 mm shank; 200 mm overall length Cooler cutting, longer tool life through internal coolant The integration of internal coolant directly to the cutting zone lowers cutting temperatures and assists chip evacuation, which translates into longer insert life and more consistent bore surfaces. By directing fluid to the interface between insert and workpiece, the tool reduces thermal expansion and minimises the risk of surface distress; the result is improved process stability and fewer reworks. The combination of coolant feed and a solid carbide body keeps the cutting edge cooler and stiffer, offering measurable gains in cycle time and tool-change intervals for repetitive production runs. Quick mounting and secure clamping for less downtime Designed with a 16 mm shank and an ISO designation of E16R SDQCL 11, the bar fits standard 16 mm toolholders and provides a compact footprint in the turret or tool post. Insert retention uses a T15 Torx key and an M3.5×8.5 clamping screw, enabling straightforward insert replacement and secure fastening that resists vibration. The bar’s nominal diameter of 20 mm and overall length of 200 mm give a well‑balanced reach for many internal bores while the modest weight (0.5 kg) reduces centrifugal load during high‑speed turning. Together these features shorten set‑up time and maintain concentricity throughout the cut. Left‑hand geometry and insert compatibility for precise bores Left‑hand cutting direction is prescribed for specific turning orientations and can be advantageous in fixtures or multi‑spindle arrangements where the turning vector requires it. The bar accepts DCMT 11T3 indexable inserts, a common triangular insert size that offers multiple cutting edges per insert and economical indexability. The cutting height 11 mm matches the insert geometry to ensure a correct, repeatable cutting plane without the need for additional shims. This setup supports high‑precision internal turning tasks where repeatability and surface integrity are priority production metrics. For technical specification checks, ordering details or to discuss integration of the Teknik Makina SDQC boring bar with internal coolant into an existing cell, contact Metav Werkzeuge at info@metav-werkzeuge.com or call +49 2822 7131930 to request consultation and supply options Technical Data Article number: KE63TM Manufacturer: Teknik Makina ISO designation: E16R SDQCL 11 Insert type: DCMT 11T3 Torx key: T15 Torx screw: M3.5x8.5 Core technical data Shank diameter: 16 mm Diameter: 20 mm Overall length: 200 mm Weight: 0.5 kg Cutting height: 11 mm Special features Internal coolant Left‑hand cutting direction Solid carbide construction Compatible with DCMT 11T3 indexable inserts FAQ Which inserts are compatible with this boring bar? The Teknik Makina Boring bar SDQC with Coolant is designed for DCMT 11T3 indexable inserts, enabling multiple re‑indexes per carbide insert for economical operation. How does the internal coolant improve machining? Internal coolant supplied through the bar directly to the cutting zone improves chip evacuation and reduces cutting temperature, which in turn prolongs insert life and stabilises bore finish when using the SDQC with coolant. What are the key mounting dimensions for toolholder selection? Mounting requires a 16 mm shank holder; the bar’s ISO designation E16R SDQCL 11 and 200 mm overall length define the clearance and reach for toolpost or turret installation. Is the cutting direction left or right handed? This tool is manufactured with a left‑hand cutting direction, suitable for operations and setups that require a left‑hand geometry. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of the combination of precise compatibility with DCMT 11T3 indexable inserts, a firm 107.5° cutting geometry and a compact 20 mm clamp height for reliable, repeatable turning operations — order directly via Metav Werkzeuge or speak with our consultants for application advice. Klemmhalter SDHCR 2020 – clamping holder for DCMT inserts, 107.5° cutting angle (right-hand) Klemmhalter for right-hand turning, designed to accept DCMT 11T3 indexable inserts for stable, high-quality facing and light to medium turning tasks Right-hand clamping holder for turning Compatible with DCMT 11T3 indexable inserts 107.5° cutting angle for stable engagement Clamp height 20 mm, cutting head width 25 mm Precision compatibility that reduces setup time The SDHCR 2020 clamping design ensures consistent seating of DCMT 11T3 indexable inserts, which are replaceable cutting tips used to maintain cutting performance without regrinding. Precise seating and the 107.5° nose angle reduce deflection and promote even wear, so cycle times remain predictable. Thanks to the measured 20 mm clamp height and a 25 mm cutting-head width, the toolholder offers a compact footprint while maintaining rigidity — an important balance for medium-duty turning where both access and stability matter. Stable clamping for repeatable results Built for right-hand operations, this clamping tool secures the insert reliably using the standard clamping geometry SDHC for DCMT. The clamp mechanism is arranged to hold inserts with minimal play, which translates to fewer re-tightening incidents and reduced micro-vibration at the cutting edge. The nominal cutting height of 25 mm aligns the cutting tip consistently with the lathe centre, lowering the risk of unexpected offsets and thus decreasing setup checks. The overall weight of 0.411 kg contributes to a robust but manageable tool assembly during handling and changeover. Practical benefits for workshop productivity Adopting a holder designed to match common ISO-designated inserts simplifies inventory and tool management. Because indexable inserts can be rotated or replaced quickly, downtime is minimised and tool life is extended in comparison with brazed or monolithic cutters. The holder’s ISO designation SDHCR 2020 denotes a standardised shank and geometry that integrate with conventional tool posts and tool blocks; the shank reference K11 assists in confirming mount compatibility. Fewer variables at setup mean predictable machining quality across repeated batches, supporting leaner production planning. Robust supplier backing and application support Sourcing this clamping holder via Metav provides access to a broad selection of compatible inserts and assembly advice from a supplier with a European distribution and quality filter in Emmerich. Metav’s extended product range and experience in precision tools mean spare parts and matching components are available quickly, reducing lead times on replacements and upgrades. For newcomers to indexable tooling, the principle is straightforward: the holder secures a replaceable insert; when the cutting edge is worn, the insert is indexed or swapped — restoring cutting performance without retooling the entire holder. For precise turning applications relying on standard DCMT inserts, choose the Teknik Makina clamping holder and contact Metav Werkzeuge for tailored guidance and quick delivery — eMail info@metav-werkzeuge.com or call +49 2822 7131930. Technical data Article number: D250TM Manufacturer: Teknik Makina Facts Clamp height: 20 mm Cutting-head width: 25 mm Cutting height: 25 mm Cutting angle: 107.5° Overall length: 125 mm Weight: 0.411 kg Direction: right Special features ISO designation: SDHCR 2020 Suitable for: DCMT 11T3 indexable inserts Shank designation: K11 Bezeichnung (English): SDHC for DCMT Indexable Inserts FAQ Which indexable inserts fit this clamping holder? The clamping holder D250TM is designed for DCMT 11T3 indexable inserts and matches the insert geometry intended by the SDHC holder family. Is the holder suitable for right-hand or left-hand turning? This model is specified for right-hand turning applications; the orientation is fixed by the tool’s cutting geometry. How does the 107.5° cutting angle affect machining? A 107.5° nose angle provides stable engagement with the workpiece, helping to distribute cutting forces and improve insert life under typical turning conditions. What does ISO designation SDHCR 2020 mean for compatibility? The SDHCR 2020 designation indicates standardised shank and clamp geometry, facilitating integration with common tool posts and simplifying replacement across similar toolholders. Can this holder reduce setup time in batch production? Yes — by accepting standard indexable inserts such as DCMT 11T3, the holder allows rapid insert changes and consistent seating, which reduces setup variability and downtime. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

The combination of fast indexable insert changes and a stable 25 mm shank ensures consistent high throughput and reduced downtime; pair this reliability with the precise 60° profile and robust 50 mm cutting diameter for dependable T-slot production. Order the T-slot cutter directly via Metav Werkzeuge or ask the consultants if assistance is required. T-slot cutter TKC250TM — 50 mm diameter, 60° cutting angle by Teknik Makina T-slot cutter TKC250TM designed for efficient production of standard 60° T-slots with indexable inserts in industrial milling applications 50 mm diameter for wide T-slot cuts Compatible with DCMT 11T3 inserts 25 mm shank diameter for secure clamping 60° cutting angle for standard T-slots Precision and productivity for repetitive T-slot machining The TKC250TM delivers a measurable productivity advantage through its 50 mm diameter and 4 cutting edges, enabling a high material removal rate when used with suitable indexable inserts. The cutter accepts DCMT 11T3 inserts, which allow quick edge changes and consistent cutting geometry, reducing non-productive time. The specification of a 60° cutting angle corresponds to the common T-slot profile, so set-up is straightforward and repeatable. The combination of robust geometry and indexable tooling supports efficient series production on CNC milling centres. Secure clamping and straightforward maintenance A 25 mm shank provides stable clamping in standard toolholders and contributes to vibration damping during heavy cuts, while the M3.5x9 Torx screw and T15 key enable rapid insert replacement without special tools. The indexable-insert design means that regrinding is avoided; worn edges are replaced in seconds, maintaining process consistency. This construction supports planned maintenance strategies: shorter changeover times and predictable tooling costs compared with solid cutters. Tool dynamics and machine compatibility With an overall length of 120 mm and a 30 mm cutting length, the cutter balances reach with rigidity for accessible T-slot machining in many workpiece setups. The tool mass of 0.521 kg contributes to dynamic stability—helping to reduce chatter when used within appropriate spindle speeds and with the right insert grade. These dimensional and mass characteristics suit production machines with adequate torque and stable fixturing, ensuring the cutter performs as intended under continuous operation. Practical setup tips and application context The TKC250TM is optimised for producing standard-profile T-slots; insert choice and cutting parameters should be matched to the workpiece material and machine capability. The indexable insert approach supports flexible selection of grades for steel, aluminium or other materials (select grade per supplier guidance). For feed and speed settings, follow the insert manufacturer's recommendations and consider machining tests to fine-tune parameters for the specific setup. For complex applications, consult Metav Werkzeuge for advice on insert grades and holder compatibility. For practical integration or specification checks of the Teknik Cutting Tools T-slot cutter TKC250TM, contact Metav Werkzeuge by phone +49 2822 7131930 or email info@metav-werkzeuge.com for tailored technical advice and ordering support. Technical data SKU: TKC250TM Product name: T-slot cutter Manufacturer: Teknik Makina Compatible inserts: DCMT 11T3 Torx screw: M3.5x9; Torx key: T15 Core dimensions Diameter: 50 mm Shank diameter: 25 mm Cutting length: 30 mm Overall length: 120 mm Cutting edges: 4 Cutting angle: 60° Weight: 0.521 kg Special features Indexable insert tool Quick insert changes with Torx fastening 4 cutting edges for productive cuts Designed for standard 60° T-slot profiles FAQ Which inserts fit the cutter? The cutter is designed for DCMT 11T3 indexable inserts; use inserts suited to the material and application for the best performance with the TKC250TM. What is the shank size and how does it affect clamping? The 25 mm shank provides secure clamping in standard toolholders and improves rigidity compared with smaller shank diameters. How many cutting edges are provided and what is their benefit? The tool has 4 cutting edges, enabling higher feed rates and smoother cutting transitions for repetitive T-slot production. What is the cutting profile angle of the tool? The cutter produces a 60° T-slot profile, which matches common industrial T-slot standards. Which fastening parts are required for insert changes? Insert retention uses a M3.5x9 Torx screw tightened with a T15 key for straightforward insert replacement. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of internal coolant, solid carbide construction and compatibility with standard indexable inserts for reliable boring operations — order directly via Metav Werkzeuge or consult our specialists for application support. Boring bar KE54TM – SDQC with internal coolant, 25 mm (Teknik Makina) The Boring bar SDQC with Coolant is a precision toolholder designed for internal-coolant boring applications and compatibility with DCMT 11T3 inserts in metalworking and CNC environments Boring bar KE54TM by Teknik Makina Internal coolant for improved chip evacuation Compatible with DCMT 11T3 indexable inserts Consistent cutting performance through internal coolant The integrated internal coolant channel maintains stable machining conditions by directing coolant to the cutting zone, which improves chip evacuation and reduces built-up edge formation. This results in more consistent surface finish and extended insert life when working through interrupted cuts or long bores. The controlled coolant delivery also helps to maintain a predictable thermal environment, aiding process repeatability and reducing the risk of premature tool wear. Robust solid-carbide construction for rigidity and longevity Constructed from solid carbide, the tool provides high rigidity and vibration resistance essential for precision turning and boring. The ISO designation E20S SDQCR 11 reflects a compact, stiff toolholder geometry optimised for demanding operations. With a compact mass of 0.95 kg, the assembly balances stiffness with manageable handling, contributing to stable cutting conditions and longer service intervals compared with less rigid alternatives. Workshop-ready dimensions and simple integration with insert systems Designed with a 25 mm cutting body and 250 mm overall length, the bar features a 20 mm shank for conventional toolholder reception and a cutting height of 13 mm, offering straightforward retrofit into existing setups. Compatibility with DCMT 11T3 indexable inserts, plus a right-hand cutting orientation and fastening via T15 Torx key and M3.5x8.5 Torx screws, ensures fast insert changes and reliable clamping. The straightforward mechanical interface reduces downtime and supports predictable cycle times in production environments. For tailored advice on integrating the Teknik Makina SDQC with internal coolant (KE54TM) into a specific process, contact Metav Werkzeuge for technical consultation and product availability at info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: KE54TM Manufacturer: Teknik Makina ISO designation: E20S SDQCR 11 Product type: SDQC with Coolant Material: Solid carbide Facts Diameter: 25 mm Overall length: 250 mm Shank diameter (aufnahme): 20 mm Cutting height: 13 mm Weight: 0.95 kg Special features Internal coolant Compatible with DCMT 11T3 indexable inserts Right-hand cutting direction Torx key T15 and Torx screw M3.5x8.5 for clamping Solid carbide construction FAQ How is the coolant supplied to the cutting edge? The KE54TM boring bar uses an integrated internal coolant channel to deliver coolant directly to the cutting zone, improving chip removal and tool life. Which insert type fits this boring bar? The bar is compatible with DCMT 11T3 indexable inserts, enabling quick replacement and established insert geometries for a range of materials. What are the key dimensions to check for machine compatibility? Key values: 25 mm diameter, 250 mm overall length, 20 mm shank diameter and 13 mm cutting height; these dimensions define mechanical fit and reach for the KE54TM boring bar. Is the cutting direction right-hand or left-hand? This tool is configured for right-hand cutting operations. What is the ISO designation for this toolholder? The tool is designated E20S SDQCR 11, which indicates its geometry and intended mounting in standard toolholder systems. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of the combination of precise clamping, internal coolant and compact dimensions to maintain cycle-time stability and extend insert life; order the holder directly via Metav Werkzeuge or consult our tooling specialists for application-specific advice. SVJCR 2525 — SVJC for VCMT Indexable Inserts, internal coolant, right-hand SVJCR 2525 is a right-hand clamping holder designed for turning applications with VCMT/DCMT-style indexable inserts; ideal for medium-duty external turning where secure insert retention and coolant supply increase productivity. Right-hand turning orientation Internal coolant supply Compatible with DCMT 11T3 inserts ISO designation SVJCR 2525 Consistent right-hand turning for stable throughput The holder delivers repeatable clamping and a defined cutting geometry that reduces setup time and stabilises cycle times. With a right-hand orientation and a 93° approach angle, the toolholder is intended for conventional turning operations where predictable chip formation and tool behaviour are required. The overall length of 150 mm and compact head width minimise overhang, which in turn reduces vibration and supports more consistent surface finish and dimensional control—benefits that translate directly into fewer reworks and higher process reliability. Secure clamping and coolant to extend insert life A secure clamping mechanism, specified under ISO SVJCR 2525, holds DCMT/VCMT indexable inserts firmly and is tightened using an M3.5x11 Torx screw (T15), ensuring repeatable torque and seating. The integrated internal coolant channel supplies coolant directly to the cutting edge; this reduces thermal load, improves chip evacuation and commonly extends the service life of carbide inserts. For manufacturers seeking to lower tooling costs per component, the combination of firm clamping and directed coolant provides a measurable reduction in wear and a more stable cutting process. Compact footprint and straightforward integration Designed with a 25 mm shank width and a 25 mm holder height, together with a 32 mm cutting-head width, this clamping holder fits common turret and toolpost setups while keeping footprint small. The modest weight of 0.735 kg and standardised interface simplify handling and changeover; the holder accepts the common DCMT 11T3 insert form factor, which facilitates stocking and reduces inventory complexity. Where quick set-up is essential, the standardised dimensions and familiar screw interface enable rapid installation with existing tooling hardware. Practical advantages for workshop and production use Because the design focuses on proven interface standards and coolant-fed cooling, it suits both jobbing shops and production lines where repeatability and uptime are priorities. The robust construction and clear ISO designation make procurement and QA processes straightforward, while the compatibility with commonly used indexable inserts ensures broad applicability across turning tasks. Technical advisors are available to discuss specific workpiece materials and machining parameters to ensure the holder matches the intended application. Contact Metav Werkzeuge for tailored tooling recommendations and request the SVJCR 2525 right-hand clamping holder with internal coolant (AP526TM) — call +49 2822 7131930 or email info@metav-werkzeuge.com Technical data Article number: AP526TM Manufacturer: Teknik Makina Designation: SVJC for VCMT indexable inserts ISO designation: SVJCR 2525 Facts Cutting height: 35 mm Holder height: 25 mm Shank width: 25 mm Cutting-head width: 32 mm Overall length: 150 mm Weight: 0.735 kg Cutting direction: right Approach angle: 93° Compatible inserts: DCMT 11T3 Coolant: internal Special features Clamping plate: TA034 Torx screw: M3.5x11 Torx key size: T15 Right-hand orientation Suitable for VCMT/DCMT indexable inserts FAQ Which insert types fit this holder? The clamping holder is intended for DCMT / VCMT indexable inserts; the geometry matches DCMT 11T3-style inserts to ensure correct seating and cutting clearance. Does the holder provide coolant to the insert tip? Yes, the toolholder features an internal coolant channel that supplies coolant close to the cutting edge to support chip control and reduce thermal loading. What fastener is used to secure the insert? An M3.5x11 Torx screw is used for insert clamping; the required Torx key size is T15, providing consistent torque for repeatable clamping. Is this holder suitable for left-hand turning? No, the holder is specified for right-hand turning; left-hand operations require the corresponding left-hand variant. Can the holder be mounted in standard toolposts and turrets? Yes, the holder's standardised shank dimensions and ISO designation are compatible with common turret and toolpost interfaces used in turning centres. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Turning Holder SDHC for DCMT Indexable Inserts by Teknik Makina The Turning Holder SDHC for DCMT Indexable Inserts is a precision clamping solution for turning applications, designed to secure DCMT 11T3 indexable inserts for reliable metalcutting operations. Teknik Makina Turning Holder SDHCR 2525 for DCMT 11T3 Secure clamping with robust SDHC design 150 mm overall length for standard toolposts Right-hand cutting with 107.5° cutting angle Compact head width 32 mm for versatile access Durable clamping and consistent cutting performance Built for repeatable results, this Turning Holder features the SDHCR 2525 ISO design that delivers stable insert seating and reduced vibration. The holder’s construction supports consistent chip flow and improved surface finish, making it suitable for serial turning tasks. With a focus on repeatability, the design reduces setup times and minimises downtime, ensuring efficient machining across batches. Compatibility with DCMT 11T3 inserts for flexible tooling Engineered specifically for DCMT 11T3 indexable inserts, the holder enables quick insert changes and secure fixation. This compatibility simplifies tooling logistics and allows workshops to use a common insert family across multiple operations. The targeted fit helps maintain cutting geometry and prolongs insert life by ensuring correct seating and pressure distribution during cutting. Compact dimensions for better accessibility and tool life The holder’s compact head width of 32 mm and a tool body of 25 mm x 25 mm allow access to confined areas while maintaining rigidity. Reduced overhang and a 150 mm overall length lower bending moments and extend tool and insert life. For operations where reach and stiffness must be balanced, this design offers improved stability without sacrificing access to tight workpiece features. Designed for workshop reliability and simple integration Manufactured by Teknik Makina, the holder is built to integrate smoothly into standard toolposts and setups. The right-hand cutting orientation and a precise 107.5° cutting angle deliver predictable chip control and repeatable results on common turning materials. For maintenance and replacement planning, the clear ISO designation and robust mounting geometry simplify inventory and procurement. Choose Teknik Makina’s Turning Holder for dependable clamping of DCMT inserts — for expert advice or technical clarification contact METAV Werkzeuge at info@metav-werkzeuge.com or call +49 2822 7131930, WhatsApp +49 170 2837271 Technical Specifications for reliable clamping Bezeichnung: Turning Holder Brand: Teknik Makina SKU: D252TM For Indexable Inserts: DCMT 11T3 Compatible Inserts: DCMT 11T3 Overall Length: 150 mm Weight: 0.738 kg ISO Designation: SDHCR 2525 Secondary Designation: M11 Width: 25 mm Height: 25 mm Cutting Head Width: 32 mm Cutting Direction: Right Cutting Angle: 107.5° GTIN: 4061905153495 Condition: New Availability: In Stock Manufacturer: Teknik Makina, Nolu Sokak, No 9, Selcuklu, Türkei, eMail: info@teknik-makina.com Responsible Person: Metav Werkzeuge GmbH, Parkring 45, 46446 Emmerich, eMail: info@metav-werkzeuge.com FAQ What inserts does the Turning Holder from Teknik Makina accept? The Teknik Makina Turning Holder is designed to accept DCMT 11T3 indexable inserts, ensuring a secure fit and correct cutting geometry for standard turning operations. Is the Turning Holder SDHCR 2525 suitable for right-hand turning only? Yes, the Teknik Makina Turning Holder SDHCR 2525 shown here is specified for right-hand cutting, which aligns with common turning setups that require that orientation. Can the Turning Holder be used in compact toolposts and confined spaces? The compact dimensions and 32 mm cutting head width of the Teknik Makina Turning Holder make it well suited for installations where accessibility and rigidity are both required. Who can I contact for technical questions about the Turning Holder? For technical questions about the Teknik Makina Turning Holder, METAV Werkzeuge offers expert advice — eMail: info@metav-werkzeuge.com, Phone: +49 2822 7131930, WhatsApp: +49 170 2837271. 150mm SDHC Turning Holder for DCMT 11T3 Indexable Inserts, SDHCR 2525, 107.5° - Teknik Makina

Take advantage of a compact, rigid tool holder that combines secure clamping with straightforward compatibility for DCMT turning inserts; its 12 mm shank dimensions and 110 mm overall length support stable turning with minimal vibration. Order directly via Metav Werkzeuge or consult our specialists for application advice. SDACR-F for DCMT Indexable Inserts — Teknik Makina tool holder, right-hand, 90° SDACR-F for DCMT Indexable Inserts is a right-hand tool holder designed for 90° turning applications using DCMT 11T3 indexable inserts, suitable for compact turret setups and precise external turning. Right-hand 90° cutting orientation Holds DCMT 11T3 indexable inserts 12 mm shank height and width 110 mm overall length Stable cutting with compact geometry The SDACR-F is engineered to deliver precision in short-reach turning operations. With a rigid 90° cutting configuration and right-hand orientation, the holder reduces tool deflection during external turning, which improves surface finish and repeatability. The compact geometry of the clamping unit helps to keep overhang low, translating into less vibration and longer insert life. The design is particularly suited for medium-duty production where consistent part quality and predictable tool behaviour are essential. Clear compatibility and secure clamping Designed specifically for DCMT 11T3 turning inserts and identified as ISO SDACR 1212, the holder’s clamping seat and screw arrangement provide reliable insert retention under variable cutting forces. The 12 mm shank height and width create a balanced fit for common toolposts and turrets, while the overall length of 110 mm allows for compact machine setup without sacrificing access. These measurable specifications mean quick verification during tool selection and simpler tool inventory management on the shop floor. Practical benefits for everyday workshop use Weighing 0.135 kg, this tool holder is lightweight yet robust, making it easy to handle during tool changes and less demanding on automated tool changers. The secure clamping reduces the need for frequent re‑adjustment, lowering setup time and increasing spindle uptime. Supplied through Metav Werkzeuge’s quality-controlled distribution, the holder comes with traceable SKU referencing for procurement and inventory control, supporting reliable supply for repetitive turning tasks. Contact Metav Werkzeuge for tailored technical advice and to request a personalised quotation for the SDACR-F tool holder (SKU D440TM); phone +49 2822 7131930 or eMail info@metav-werkzeuge.com Technical data Article number: D440TM Manufacturer: Teknik Makina Designation: SDACR-F for DCMT Indexable Inserts ISO designation: SDACR 1212 Facts Overall length: 110 mm Shank height: 12 mm Shank width: 12 mm Cutting head width: 12 mm Weight: 0.135 kg Cutting angle: 90° Special features Suitable for DCMT 11T3 inserts Right-hand cutting direction ISO toolholder form SDACR 1212 Bezeichnung_2_en provided: SDACR-F for DCMT Indexable Inserts FAQ Which inserts fit this holder? The holder is designed for DCMT 11T3 indexable inserts; the seating and clamping geometry match that insert specification for secure retention. Is the holder right-hand or left-hand? This tool holder is configured for right-hand turning operations and a 90° cutting orientation, as specified by the SDACR form. What are the key dimensions to check for machine compatibility? Important dimensions are the 12 mm shank height and width and the 110 mm overall length; verify these against the turret or toolpost envelope. How heavy is the tool holder and what does that mean in practice? The holder weighs 0.135 kg, which makes it easy to handle during manual changes and reduces inertia on automatic changers while maintaining adequate rigidity. Can this holder be used for heavy interrupted cuts? The SDACR-F's compact design and secure clamping are intended for stable external turning; for heavy interrupted cuts, assess machine power and insert grade accordingly. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Reliable turning performance is achieved through precise clamping, internal coolant and a defined 93° cutting angle, delivering stable chip control and repeatable surface quality; compact dimensions (150 mm length, 35 mm cutting height) support secure setups. Order the SVJC for VCMT indexable inserts directly via Metav Werkzeuge or ask our consultants if needed. SVJC for VCMT Indexable Inserts – SVJCR 2020 turning holder with internal coolant (Teknik Makina) The SVJC for VCMT Indexable Inserts is a right‑hand turning holder engineered for secure clamping of DCMT/VCMT‑style indexable inserts in general turning operations. Right‑hand turning holder with internal coolant Compatible with DCMT/VCMT 11T3 inserts ISO designation SVJCR 2020 for reliable fit Compact 150 mm length, 35 mm cutting height Consistent clamping for repeatable results A robust clamping design provides secure clamping of indexable plates, reducing vibration at the cutting edge and improving surface finish. The holder’s geometry with a 93° cutting angle ensures predictable chip flow and stable cutting forces, which is particularly beneficial in finishing passes and serial production. The ISO designation SVJCR 2020 guarantees compatibility with standard tool posts and quick replacement cycles, supporting consistent set‑ups and reduced machine downtime. Controlled coolant flow to extend tool life The integrated internal coolant channel directs lubricant precisely to the cutting zone, aiding in chip control and thermal management. This reduces flank wear and helps maintain edge integrity for longer, improving overall tool life. For right‑hand turning operations the holder’s coolant routing supports uninterrupted machining at higher speeds while maintaining reliable chip evacuation, which contributes to fewer interruptions and higher process stability. Designed for quick assembly and secure fastening Assembly and insert changes are straightforward thanks to the defined clamping parts and fasteners: the clamping plate TA034, Torx drive T15 and screw M3.5x11 ensure repeatable torque and secure seating. With an overall length of 150 mm, a cutting height of 35 mm and a head width of 32 mm, the holder offers a compact footprint that is easy to position in tight toolrooms. The mass of 0.735 kg provides a good balance between rigidity and dynamic response for most medium‑duty turning tasks. Practical supply and reliability for workshop routines Compatibility with common indexable plates such as DCMT 11T3 reduces the need for special tooling inventories and speeds up changeovers. The combination of standardised interface and practical dimensions supports efficient inventory management and flexible machine assignment. Backed by an established distributor and a broad product range, workshops benefit from a dependable supply chain and sensible logistics directly from the European distribution centre. Contact Metav Werkzeuge for a tailored quote on the SVJCR 2020 clamping holder AP525TM and fast delivery from Emmerich Technical Data SKU: AP525TM Item: SVJC for VCMT Indexable Inserts Manufacturer: Teknik Makina ISO designation: SVJCR 2020 eClass: 21181004 Facts Overall length: 150 mm Cutting height: 35 mm Holder height: 25 mm Cutting head width: 32 mm Weight: 0.735 kg Cutting angle: 93° Special features Right‑hand cutting direction Internal coolant Compatible with DCMT 11T3 inserts Clamping plate: TA034 Torx key: T15 Torque screw: M3.5x11 Boring bar designation: K16-IK FAQ Which insert types fit this holder? The SVJC for VCMT indexable inserts (SVJCR 2020, AP525TM) is compatible with DCMT 11T3‑style plates and VCMT variants that match the same pocket geometry. Is the coolant internal or external? Internal coolant is provided via a dedicated channel, enabling targeted lubrication at the cutting edge to improve chip evacuation and reduce wear. Can the holder be used for finishing operations? Yes; the combination of a 93° cutting angle and secure clamping makes the holder suitable for finishing passes where surface quality and dimensional repeatability are required. What fastening hardware is required for assembly? Assembly uses the clamping plate TA034 with a Torx T15 drive and a M3.5x11 screw to ensure consistent clamping force and repeatable replacement. Is this a left‑hand or right‑hand holder? This toolholder is designed for right‑hand cutting direction and is specified accordingly in the product data. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com