High-precision drills for reliable, high-throughput metalworking
Drills provide the fundamental rotating cutting solution for producing accurate cylindrical holes in materials such as structural steel, high-alloy stainless steel, cast iron, non-ferrous metals and engineering plastics, delivering consistent hole quality and extended tool life in CNC machining and turning centres. This category covers everything from classic twist drill made from high-speed steel for general machining to solid carbide drill optimised for high cutting speeds and long run times, offering advanced coatings and internal coolant options for improved heat management. By using optimised point geometries and split points the tools reduce thrust, prevent walking at the start of the cut and ensure superior surface finish, which benefits sectors from general mechanical engineering to automotive component manufacture.
9.8mm HSS-G Twist Drill DIN 338 ,short, bright finished, Type N - MetavCUT
Kombinieren Sie die HSS-G-Schneidleistung mit der kurzen Ausführung für höhere Stabilität und schnellere Bohrzyklen; profitieren Sie von einem Spitzenwinkel 135° für harte Werkstoffe und von reduzierter Anpresskraft bei anspruchsvollen Metallarbeiten. Bestellen Sie den Spiralbohrer direkt über Metav oder nutzen Sie unsere technische Beratung bei Rückfragen. Spiralbohrer 9,8 mm, HSS-G, kurze Ausführung Spiralbohrer 9,8 mm in kurzer Ausführung, geschliffen und nach DIN 338 klassifiziert, für präzise Metallbohrungen in Werkstatt und Produktion. Spiralbohrer 9,8 mm, HSS-G, geschliffen Kurze Ausführung für hohe Stabilität Spitzenwinkel 135° für harte Werkstoffe Bis zu 40 % schnelleres Bohren bei 50 % weniger Anpresskraft Geeignet für Handbohrmaschine und stationäre Maschinen Mehr Leistung durch gehärtetes Material und präzise Geometrie Der HSS-G-Werkstoff kombiniert hohe Verschleißfestigkeit mit guter Schneidhaltigkeit und eignet sich deshalb besonders für legierten und unlegierten Stahl sowie Gussmaterialien. Durch die geschliffene Fertigung entsteht eine sehr scharfe Schneide, die das Eindringen in hartes Material erleichtert und saubere Bohrlöcher erzeugt. Für Anwender bedeutet das: geringerer Kraftaufwand, höhere Prozesssicherheit und weniger Nacharbeit bei Passungen. Kurze Ausführung für höhere Stabilität und Genauigkeit Die kurze Auskraglänge reduziert die Hebelwirkung und minimiert das Verbiegen während des Bohrens. In Kombination mit der Spirallänge von 87 mm und der Gesamtlänge von 133 mm sorgt das für einen stabilen Schnitt und bessere Rundlaufgenauigkeit bei stationären und handgeführten Anwendungen. Die Einhaltung der DIN 338 und die geschliffene Schaftausführung unterstützen präzise Bohrbilder bei anspruchsvollen Metallbearbeitungen. Praxisorientierte Anwendungsempfehlungen für Metall Mit einem Durchmesser von 9,8 mm gehört dieser Bohrer zum Standard-Bereich und eignet sich für Werkstattarbeiten, Montage und DIY-Projekte an dünnen bis mittleren Blechen, Profilen und Flachstahl. Für besonders präzise Bohrungen empfiehlt sich vorheriges Anpünkteln, um ein Wandern des Werkzeugs zu vermeiden. Die Kombination aus 135° Spitzenwinkel und der geschliffenen Geometrie reduziert Einbohrkräfte in harten Werkstoffen wie Edelstahl. Hinweise zur Anwendung und Standzeitoptimierung Für lange Standzeiten empfehlen sich Kühlung und moderater Vorschub, insbesondere bei Mehrfachbohrungen oder temperatursensiblen Werkstoffen. Tiefe Löcher sollten schrittweise aufgebohrt werden, um die Spanabfuhr sicherzustellen. Der Spiralbohrer ist für Handbohrmaschine und stationäre Maschinen ausgelegt; bei stationärem Einsatz zeigt sich die beste Performance und die geringste Bruchgefahr. Empfehlung: Vertrauen Sie auf die Profi Line von MetavCUT und nutzen Sie den kurzen HSS-G Spiralbohrer für präzise Metallbearbeitung; bei technischen Fragen erreichen Sie unsere Beratung per E‑Mail info@metav-werkzeuge.com oder Telefon +49 2822 7131930. Leistungsmerkmale Artikelnummer: 48098-FDA Marke: MetavCUT Modellserie: Profi Line Bezeichnung: Spiralbohrer Typ: Typ N Fakten Durchmesser: 9,8 mm Gesamtlänge: 133 mm Spirallänge: 87 mm Spitzenwinkel: 135° Verpackungseinheit: 5 Besonderheiten Material: HSS-G (Schnellarbeitsstahl, geschliffen) Schaftausführung: geschliffen Norm: DIN 338 Ausführung: kurz Farbe: blank Einsatz: Handbohrmaschine FAQ Wie unterscheidet sich dieser geschliffene Spiralbohrer von walzgegossenen Bohrern? Der geschliffene Spiralbohrer von MetavCUT bietet schärfere Schneidkanten und höhere Rundlaufgenauigkeit, was zu saubereren Bohrlöchern in Metall führt; solche Bohrer sind ideal für präzise Anwendungen, während walzgegossene Varianten oft zäher und weniger spröde sind. Für welche Materialien ist der Spiralbohrer 9,8 mm besonders geeignet? Der Spiralbohrer der Profi Line von MetavCUT ist konzipiert für legierten und unlegierten Stahl, Gussstahl, Gusseisen, Sintereisen sowie Nichteisenmetalle und Hartkunststoff; der 135° Spitzenwinkel erleichtert das Anbohren harter Werkstoffe. Kann der Bohrer in einer Handbohrmaschine verwendet werden? Ja, der Spiralbohrer ist für Handbohrmaschine und stationäre Maschinen geeignet; bei handgeführten Einsätzen sorgt die kurze Ausführung für höhere Stabilität und geringere Verkantungsneigung. Welche Vorteile bringt die kurze Ausführung bei der täglichen Arbeit? Die kurze Ausführung reduziert Auskraglänge und Biegebeanspruchung, was die Präzision erhöht und die Bruchgefahr verringert; Anwender profitieren von schnellerem Bohren und einem sichereren Fertigungsprozess. Welche SKU hat dieses Produkt und wie viele Stück sind pro Einheit? Das Produkt ist gelistet unter SKU 48098-FDA und wird in einer Verpackungseinheit von 5 Stück geliefert.
9.9mm HSS Twist Drill DIN 338 ,short, roll forged, black, Type N - MetavCUT
Robuste Kombination aus HSS, kurzer Ausführung und 118° Spitzenwinkel sorgt für hohe Stabilität und saubere Bohrungen in Metall. Profitieren Sie von der Präzision der kurzen Bauweise und der Eignung für gängige Werkstoffe; bestellen Sie das Produkt direkt über Metav Werkzeuge oder fragen Sie unsere Beratung bei Bedarf an. Spiralbohrer von MetavCUT — kurzer HSS-Bohrer für Metall Der Spiralbohrer ist ein kurzer HSS-Bohrer nach DIN 338, ausgelegt für präzise Metallbohrungen an Hand- und stationären Maschinen. MetavCUT Spiralbohrer »40099-FDA« HSS kurz Für Metallbearbeitung und Handbohrmaschinen geeignet Kurze Bauweise für höhere Stabilität und Präzision Typ N Normalspirale für gängige Stahlarbeiten 9,9 mm Durchmesser für Standardanwendungen Hohe Stabilität durch kurze Bauweise für saubere Bohrungen Die kurze Ausführung reduziert die Auskraglänge und erhöht dadurch die Stabilität beim Bohren in Stahl und Guss. Durch die verminderte Biegebelastung entsteht weniger Laufunruhe, sodass saubere Bohrungen mit geringerer Nachbearbeitung möglich sind. Anwender profitieren von geringerer Bruchgefahr und konstanteren Bohrbildern bei mittleren Durchmessern. Materialeigenschaften von HSS und Bedeutung für die Praxis HSS steht für Schnellarbeitsstahl und kombiniert Elastizität mit Schnittfestigkeit, was insbesondere bei Bohrungen unter 6 mm das Bruchrisiko senkt. Bei einem Durchmesser von 9,9 mm ermöglicht HSS dennoch zähere Schnitte in legierten und unlegierten Stählen sowie in Nichteisenmetallen. Für Anwender bedeutet das eine zuverlässige Werkzeuggleistung auch bei wechselnden Materialqualitäten. Normgerecht und praxistauglich: DIN 338 und Typ N erklärt Die Norm DIN 338 definiert kurze Spiralbohrer mit Zylinderschaft und gibt Fertigungs- und Abmessungsrichtlinien vor, die Wiederholgenauigkeit und Austauschbarkeit sichern. Die Typ N Normalspirale ist die klassische Ausführung für Metall und bietet eine ausgewogene Spanabfuhr für mittlere Werkstoffe. Das Resultat ist planbare Qualität bei der Bearbeitung von Blechen, Profilen und Maschinenbauteilen. Anwendungshinweise für saubere Ergebnisse und lange Standzeiten Vor dem Bohren empfiehlt sich ein Anpunktieren oder Zentrieren, um das Wandern des Bohrers zu minimieren. Bei 9,9 mm Durchmesser ist direkter Bohrbetrieb möglich, bei hoher Präzision aber zusätzliches Anpunkten sinnvoll. Kühlschmierstoffe verlängern die Standzeit von HSS deutlich; bei zähen Werkstoffen ist reduzierte Vorschubgeschwindigkeit zu empfehlen, um Überhitzung zu vermeiden. Für wen dieses Werkzeug entwickelt wurde Dieser Bohrer richtet sich an Werkstätten, Maschinenbauer und ambitionierte Heimwerker, die robuste und genormte Werkzeuge für Metallarbeiten benötigen. Die kurze Bauform ist besonders geeignet für Arbeiten an festen Spannvorrichtungen und stationären Säulenbohrern sowie für Einsätze, bei denen Stabilität und Genauigkeit wichtiger sind als Reichweite. Empfehlung: Setzen Sie auf die bewährte Qualität von MetavCUT und wählen Sie den kurzen HSS-Bohrer für präzise Metallbohrungen; bei Fragen erreichen Sie unseren technischen Vertrieb direkt über info@metav-werkzeuge.com oder telefonisch unter +49 2822 7131930 Produktmerkmale Bezeichnung: Spiralbohrer Hersteller: MetavCUT Material: HSS (Schnellarbeitsstahl) Norm: DIN 338 Typ: Typ N SKU: 40099-FDA Fakten Durchmesser: 9,9 mm Gesamtlänge: 133 mm Spirallänge: 87 mm Spitzenwinkel: 118° Verpackungseinheit: 5 Besonderheiten Ausführung: kurz Farbe: schwarz Für Bohrmaschine: Handbohrmaschine HSS: Schnellarbeitsstahl für metallische Werkstoffe DIN 338: Norm für kurze Spiralbohrer mit Zylinderschaft FAQ Welche Werkstoffe eignen sich für diesen Spiralbohrer? Der MetavCUT Spiralbohrer (Typ N, HSS, SKU 40099-FDA) ist geeignet für legierten und unlegierten Stahl, Gusseisen, Nichteisenmetalle und Kunststoffe; für sehr zähe Werkstoffe sollte Kühlschmierstoff eingesetzt werden. Ist der kurze Bohrer für Handbohrmaschinen verwendbar? Ja, die kurze Ausführung des MetavCUT Spiralbohrers ist für Handbohrmaschine und stationäre Maschinen geeignet und bietet durch reduzierte Auskraglänge mehr Stabilität. Warum ist der Spitzenwinkel 118° relevant? Ein Spitzenwinkel von 118° erleichtert das Anbohren und ist besonders vorteilhaft bei gängigen Metall- und Nichteisenwerkstoffen, da er gute Zentrierung und effiziente Spanbildung ermöglicht.
9.9mm HSS-E Twist Drill DIN 338 ,short, 5% cobalt-alloyed, Type N - MetavCUT
Spiralbohrer 47099-FDA von MetavCUT — kurzer HSS‑E Bohrer für Metall Der Spiralbohrer 47099-FDA ist ein kurzer HSS‑E Spiralbohrer für präzise Metallbohrungen an Handbohrmaschinen und stationären Maschinen. Kurze Ausführung für erhöhte Stabilität HSS‑E mit 5% Kobalt für härtere Werkstoffe Geschliffener Schaft für hohe Rundlaufgenauigkeit Spitzenwinkel 135° für Edelstahl und gehärteten Stahl Gesamtlänge 133 mm, Spirallänge 87 mm Mehr Stabilität und Präzision beim Metallbohren Die kurze Ausführung dieses Spiralbohrers reduziert die Auskraglänge und minimiert damit Vibrationen sowie Verbiegen beim Bohren. Das Ergebnis sind saubere Bohrlöcher und ein geringeres Bruchrisiko, besonders bei anspruchsvollen Metallarbeiten. Anwender profitieren von höherer Vorschubstabilität und gleichbleibender Maßhaltigkeit selbst bei wiederholten Bohrvorgängen. Materialqualität und Schnittverhalten für harte Werkstoffe Der Bohrer besteht aus HSS‑E (Hochlegierter Schnellarbeitsstahl) mit 5% Kobalt, was die Rotbeständigkeit und Verschleißfestigkeit erhöht. Durch die Legierung bleibt die Schneide auch bei höheren Temperaturen länger scharf, sodass das Werkzeug bei Stahl, Gusseisen und Nichteisenmetallen zuverlässige Standzeiten liefert. Ein Vorteil ist die Kombination aus Zähigkeit und Schnitthaltigkeit für anspruchsvolle Einsätze. Vielseitige Anwendung für Werkstatt und Montage Mit einem Durchmesser von 9,9 mm gehört dieser Bohrer in den Standard‑Bereich und eignet sich sowohl für Handbohrmaschinen als auch für stationäre Säulenbohrmaschinen. Für präzise Ergebnisse empfiehlt sich punktgenaues Anpunkten vor dem Bohren. Das macht den Bohrer zur guten Wahl für Werkstätten, Montagen und für industrielle Instandsetzungsarbeiten, bei denen Alltagstauglichkeit und Zuverlässigkeit gefragt sind. Normgerecht gefertigt und auf Genauigkeit ausgelegt Der Spiralbohrer erfüllt die Vorgaben der DIN 338, was die Typisierung als kurze Spiralbohrer mit Zylinderschaft bestätigt. Die geschliffene Fertigung sorgt für sehr scharfe Kanten und hohe Rundlaufgenauigkeit, ideal für saubere Bohrbilder. Anwender sollten beim Bohren in dicken Werkstücken Kühlung einsetzen und bei Bedarf stufenweise aufbohren, um beste Ergebnisse zu erzielen. Sichern Sie sich den MetavCUT Kurzbohrer aus der Standard Line für präzise Metallbearbeitung und profitieren Sie von Verfügbarkeit und fachkundiger Beratung direkt aus Emmerich — bei Rückfragen eMail an info@metav-werkzeuge.com oder Telefon +49 2822 7131930 Produktmerkmale Artikelnummer: 47099-FDA Marke: MetavCUT Bezeichnung: Spiralbohrer Serie: Standard Line Hersteller: MetavCUT Norm: DIN 338 Daten Durchmesser: 9,9 mm Gesamtlänge: 133 mm Spirallänge: 87 mm Spitzenwinkel: 135° Verpackungseinheit: 5 Besonderheiten Material: HSS-E (Hochlegierter Schnellarbeitsstahl) Legierung: 5% Kobalt Schaftausführung: geschliffen Ausführung: kurz Für Bohrmaschine: Handbohrmaschine Typ: Typ N (Normalspirale) Norm: DIN 338 (kurze Spiralbohrer mit Zylinderschaft) FAQ Für welche Materialien ist dieser Spiralbohrer geeignet? Der MetavCUT Spiralbohrer 47099-FDA ist für legierten und unlegierten Stahl, Gusseisen, Nichteisenmetalle und Kunststoff ausgelegt und liefert dank HSS‑E mit 5% Kobalt gute Standzeiten bei härteren Werkstoffen. Kann der Bohrer in einer handgeführten Akkubohrmaschine verwendet werden? Ja, der Spiralbohrer aus der Standard Line ist für Handbohrmaschinen geeignet; bei starkem Vorschub oder sehr harten Materialien empfiehlt sich eine stationäre Maschine oder reduzierter Vorschub zur Verlängerung der Lebensdauer. Worin liegt der Vorteil der geschliffenen Schaftausführung? Die geschliffene Ausführung sorgt für hohe Rundlaufgenauigkeit und scharfe Schneiden, wodurch der Bohrer präzise und saubere Bohrlöcher erzeugt, ideal für Metallbearbeitung mit engen Toleranzen. Warum ist der Spitzenwinkel 135° wichtig? Ein Spitzenwinkel von 135° reduziert das Einstechen bei harten Werkstoffen wie Edelstahl und sorgt für kontrollierteres Anbohren sowie verringerte Ausrissbildung an der Austrittskante. Welche Norm beschreibt diesen Bohrertyp und was bedeutet das? Die DIN 338 spezifiziert kurze Spiralbohrer mit Zylinderschaft; bei diesem MetavCUT Spiralbohrer bedeutet das standardisierte Abmessungen und Fertigungsqualität, die für industrielle Anwendungen geeignet sind.
9.9mm HSS-G Twist Drill DIN 338 ,short, bright finished, Type N - MetavCUT
Twist Drill — Type N, 9.9 mm, 135° tip, short, bright finished, HSS‑G, DIN 338 (MetavCUT) The Twist Drill Type N is a short HSS‑G drill for precision metal drilling, designed for use in hand and machine drilling applications. Short design for improved stability 135° tip for hard materials HSS‑G fully ground for precise holes Conforms to DIN 338 for metalworking Precision and performance for demanding metalwork Designed for accurate metal drilling, this HSS‑G short Twist Drill delivers consistently clean holes with high roundness. The fully ground geometry produces very sharp cutting edges and excellent runout characteristics, which reduces burr formation and improves hole quality. For users seeking reliable results in alloyed and unalloyed steels, the combination of Type N spiral and a 135° point angle supports controlled penetration and reduces lateral wandering during the initial drill entry. Short length for stability and faster operation Because the bit has a reduced protruding length, the short design significantly increases rigidity and lowers the tendency to bend under load. This leads to measurable workflow benefits: the grinded HSS geometry enables drilling up to 40% faster while requiring 50% less feed force compared with conventional HSS variants. Contractors and workshop technicians working on small setups or clamped workpieces profit from improved precision and less chatter when using a compact, robust drill of this design. Geometry and materials optimised for hard materials The 135° tip angle is chosen specifically to assist drilling into harder materials such as stainless steel and tempered components; a larger point angle shortens initial bite time while maintaining tool life. The designation DIN 338 classifies this short Twist Drill with a cylindrical shank and describes the ground manufacturing process; grinding (HSS‑G) creates sharp cutting lips but can make the tool more brittle, so coolant and steady machine setup are advisable to avoid premature breakage. Who benefits and practical usage advice This Twist Drill is targeted at professional users and advanced hobbyists needing reliable metal drilling — especially for precision work on lathe‑mounted or stationary drilling machines and well‑supported handheld drilling operations. The fully ground shank ensures good chucking accuracy; for best results, secure the workpiece, use appropriate cutting fluid and moderate feed, and avoid excessive overhang. MetavCUT’s short series is particularly suitable when stability and accuracy are priorities over reach. Strongly recommended: choose the MetavCUT short HSS‑G Twist Drill Type N for demanding metal applications — for personalised technical advice and ordering support contact METAV Werkzeuge at info@metav-werkzeuge.com, call +49 2822 7131930 or message via WhatsApp +49 170 2837271 Designation: Twist Drill Brand: MetavCUT SKU: 45099-FDA Diameter: 9.9 mm Tip angle: 135° Type: Type N Execution: Short Colour: Bright finished Material: HSS‑G Shank finish: Fully ground Spiral length: 87 mm Overall length: 133 mm For drill machine: Drilling Machine (Hand drill) Model series: Standard Line Norm: DIN 338 Application: Drills for metal Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What are Twist Drills used for and which materials suit them best? The MetavCUT Twist Drill Type N is primarily used for drilling metal; it is especially effective on alloyed and unalloyed steels, cast materials and non‑ferrous metals. Its geometry and 135° point make it suitable for harder workpieces where accurate centring and reduced walking are required. Which three drill types are commonly distinguished? In general practice three main categories are identified: metal drills, wood drills and stone/concrete drills. The MetavCUT Twist Drill Type N belongs to the metal drill group and is optimised for machining metallic materials. Can the MetavCUT Twist Drill be used in a handheld drill or only in machine tools? The short design of the MetavCUT Twist Drill Type N improves rigidity and makes it suitable for both well‑supported handheld drilling and stationary machine tools; however, optimum precision is achieved in clamped or machine setups with appropriate cooling. Why is the tip of a Twist Drill ground to a specific angle? The 135° tip on the MetavCUT Twist Drill reduces initial cutting forces and improves centring in hard materials; grinding the tip also reduces the cross‑cut width, lowering friction and the required feed, which helps achieve cleaner holes with less tool wear.
9.9mm HSS-G Twist Drill DIN 338 ,short, bright finished, Type N - MetavCUT
Kompakte Bauweise und geschliffene HSS-G Geometrie sorgen für hohe Stabilität und präzise Bohrungen in Stahl und Guss. Der 135° Spitzenwinkel erleichtert das Anbohren harter Werkstoffe, während die kurze Ausführung Schwingungen reduziert. Bestellen Sie den Spiralbohrer direkt über Metav Werkzeuge oder fragen Sie unsere Beratung bei Bedarf an. Spiralbohrer – MetavCUT Profi Line Kurzbohrer Spiralbohrer aus der Profi Line für präzise Metallbohrungen mit kurzer Ausführung und hoher Rundlaufgenauigkeit. Kurze Ausführung für höhere Stabilität Geschliffen nach DIN 338 für scharfe Kanten Spitzenwinkel 135° für hartes Material HSS-G Material für legierten und unlegierten Stahl Spirallänge 87 mm für zuverlässige Spanabfuhr Robuste Materialwahl für dauerhafte Präzision Der geschliffene HSS-G Werkstoff kombiniert Verschleißfestigkeit mit Schneidfähigkeit und ist speziell auf die Bearbeitung von Stahl, Gussstahl und Nichteisenmetallen abgestimmt. Durch die geschliffene Schaftausführung entsteht eine sehr hohe Rundlaufgenauigkeit, die saubere, maßhaltige Bohrlöcher ermöglicht. Für Anwender bedeutet das weniger Nacharbeit und konstante Ergebnisse bei stationären wie handgeführten Maschinen. Kurze Ausführung für mehr Stabilität und Kontrolle Die kurze Bauform reduziert Auskraglänge und damit Biegebelastung sowie Schwingungsneigung. Das führt zu stabilerem Lauf, höherer Präzision und deutlich geringerem Bruchrisiko bei zähen Materialien. Die Spirallänge 87 mm sorgt trotzdem für effektive Spanabfuhr, sodass in vielen Metallanwendungen saubere Bohrbilder erzielt werden, ohne auf Stabilität verzichten zu müssen. Geometrie und Anwendung für harte Werkstoffe Der Spitzenwinkel 135° optimiert das Eindringen in gehärtete Werkstoffe und verringert das Ausbrechen beim Austritt. In Kombination mit der kurzen Ausführung eignet sich der Bohrer besonders für präzise Bohrungen in legiertem Stahl, Gusseisen und Temperguss. Die Typ-N Normalspirale ist die bewährte Lösung für klassische Metallbearbeitung und erlaubt zuverlässige Ergebnisse bei üblichen Schnittparametern. Praktische Hinweise für den Werkstattalltag Für beste Ergebnisse empfiehlt sich Vorbohren bei sehr dicken oder harten Teilen sowie der Einsatz von Kühlschmierstoff bei stationären Anwendungen. Bei Handbohrmaschinen bietet der kurze Bohrer erhöhte Stabilität; bei sehr tiefen Löchern ist die Begrenzung der Bohrtiefe zu beachten. Die DIN 338 Klassifizierung garantiert standardisierte Abmessungen und Kompatibilität mit gängigen Spannfuttern. Mit dem MetavCUT Profi Line Spiralbohrer 9,9 mm präzise Bohrungen sichern – Beratung und Bestellung direkt über Metav Werkzeuge per eMail info@metav-werkzeuge.com oder Telefon +49 2822 7131930. Produktmerkmale Artikelnummer: 48099-FDA Marke: MetavCUT Serie: Profi Line Bezeichnung: Spiralbohrer Typ: Typ N Ausführung: kurz Schaftausführung: geschliffen Daten Durchmesser: 9,9 mm Gesamtlänge: 133 mm Spirallänge: 87 mm Spitzenwinkel: 135° Verpackungseinheit: 5 Besonderheiten Material: HSS-G Norm: DIN 338 Oberfläche: blank (bright finished) Für Bohrmaschine: Handbohrmaschine Geeignet für: legierter Stahl, unlegierter Stahl, Gussstahl, Gusseisen, Sintereisen, Temperguss, Nichteisenmetalle, Hartkunststoff FAQ Wie unterscheidet sich die kurze Ausführung von einem Standardbohrer? Die kurze Ausführung reduziert die Auskraglänge und erhöht dadurch die Stabilität beim Bohren. Der MetavCUT Profi Line Spiralbohrer bietet so weniger Schwingungen und eine bessere Rundlaufgenauigkeit im Vergleich zu längeren Bohrern. Ist der geschliffene HSS-G Spiralbohrer für Edelstahl geeignet? Der geschliffene HSS-G Bohrer mit 135° Spitzenwinkel eignet sich für viele gehärtete Werkstoffe; bei sehr zähem Edelstahl sind jedoch angepasste Schnittdaten und Kühlschmierstoff empfehlenswert, um Standzeit und Bohrergebnis zu optimieren. Welche Maschine passt am besten für diesen Bohrertyp? Der MetavCUT Profi Line Spiralbohrer ist für stationäre Säulenbohrmaschinen und Handbohrmaschinen einsetzbar; die kurze Ausführung erhöht die Eignung für handgeführte Anwendungen, solange das Spannfutter das Maß sicher hält. Wie beeinflusst die Typ-N Normalspirale die Anwendung? Die Typ-N Normalspirale ist die klassische Geometrie für Metallbohrungen und bietet eine ausgewogene Spanabfuhr sowie gute Zentration beim Anbohren, ideal für allgemeine Werkstatt- und Industrietätigkeiten.
9mm HSS Twist Drill DIN 338 ,short, roll forged, black, Type N - MetavCUT
Twist Drill — Type N short, Ø 9 mm, 118° tip, black, HSS, DIN 338 (MetavCUT) The Twist Drill Type N short is a high‑stability HSS metal drill designed for precise holemaking in steel and other metals with a 9 mm diameter and a 118° tip angle. Short HSS design for enhanced stiffness 9 mm diameter for standard metal holes 118° tip for reliable centering Complies with DIN 338 for short twist drills Black finish for corrosion resistance Precision and durability from HSS material High Speed Steel (HSS) gives this Twist Drill outstanding elasticity and resistance to fracture during common metalworking tasks. The HSS composition is especially suitable for drilling alloyed and unalloyed steel, cast iron, non‑ferrous metals and plastics, providing dependable tool life under typical workshop conditions. The short execution reduces flex and vibration, resulting in consistently round holes and longer tool service intervals. Better control and centering with a 118° tip A 118° point angle improves centering on curved or slightly irregular surfaces and reduces walking at the drill start, which is useful when producing clean, accurate holes in softer steels and aluminium. Because the tip geometry affects feed forces and heat generation, this configuration balances penetration speed and control for general metalworking. Users benefit from fewer re‑drills and faster set‑up when precision is required. Stable short design according to DIN 338 Manufactured to DIN 338, the short twist drill format prioritises stiffness and dimensional accuracy. This Type N short design minimizes overhang from the chuck, lowering the risk of bending and enabling higher feed rates on both portable and stationary drilling machines. MetavCUT’s adherence to this standard means predictable performance and interchangeability with other DIN‑compliant tooling in professional environments. Practical use recommendations for workshop and on‑site work When using this MetavCUT Twist Drill in a drilling machine or a hand drill, moderate cutting speeds and steady feed ensure optimal results; excessive speed can shorten tool life. For holes up to moderate depths, the short overall length (125 mm) and spiral length (81 mm) improve chip evacuation and reduce runout. Professionals and serious hobbyists will appreciate the combination of robustness and ease of resharpening that HSS tools offer. Highly recommended: For precise metal drilling choose the MetavCUT Twist Drill Type N short in HSS for reliable centering and enhanced stiffness — for personalised technical advice METAV Werkzeuge provides expert consultation via eMail: info@metav-werkzeuge.com, Phone: +49 2822 7131930 or WhatsApp: +49 170 2837271 Designation: Twist Drill Brand: MetavCUT SKU: 40090-FDA Diameter: 9 mm Point angle: 118° Type: Type N Colour: black Version: short Material: HSS Standard: DIN 338 Spiral length: 81 mm Overall length: 125 mm Application: Drills for metal For use with: Drilling Machine / Hand Drill Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What is the MetavCUT Twist Drill Type N short best used for? The MetavCUT Twist Drill Type N short is intended primarily for drilling metal; it excels in producing accurate holes in alloyed and unalloyed steel, cast iron and non‑ferrous metals thanks to its HSS construction and short, stiff geometry. Can this Twist Drill be used in a hand drill? Yes, the MetavCUT Twist Drill short execution can be used in a hand drill or a drilling machine, but best results come from steady speeds and controlled feed to maintain centering and to avoid excessive wear. What are Twist Drills used for? Twist Drills are mainly applied when machining high‑strength materials and larger diameters. Their form allows straightforward resharpening and sustains higher loads; the design suits metalworking and larger bore tasks. Which three drill types exist? There are three principal drill types: Metal drills, Wood drills and Stone/Concrete drills.
9mm HSS-E Twist Drill DIN 338 ,short, 5% cobalt-alloyed, Type N - MetavCUT
Twist Drill – Short HSS‑E Type N, Ø 9 mm, 135°, 5% Cobalt‑Alloyed, DIN 338 (MetavCUT) The Twist Drill from MetavCUT is a short Type N drill for precise metalworking, especially suited to drilling hard and alloyed steels with a 135° tip angle. Short design for high stability 135° tip for hard materials Fully ground flutes for precise holes HSS‑E with 5% cobalt for heat resistance Conforms to DIN 338 for short drills Greater Precision through Short Design and Material Choice The short Execution reduces overhang and increases Stability, which is particularly beneficial when machining hard metals. Manufactured in HSS‑E with 5% Cobalt‑Alloyed composition, the tool offers improved heat resistance and wear behaviour compared with standard HSS. As a result, operators achieve cleaner holes and longer tool life when performing demanding Metalworking tasks on stationary or portable Drilling Machines. Clean Holes and High Runout Accuracy with Ground Geometry A Fully ground flute geometry produces very sharp cutting edges and excellent Runout Accuracy, ideal for precision applications. The Type N spiral geometry is the classic choice for Metal Drilling and generates reliable chip evacuation in many alloys. Note that ground drills can be more brittle than rolled variants, therefore using appropriate cooling and careful feed rates on tougher Materials is recommended to avoid breakage. Designed for Metalworking: Recommended Applications and Users This MetavCUT Twist Drill is intended for drilling Alloyed and Unalloyed Steel, Cast Iron, Non‑Ferrous Metals and certain Plastics; it is well suited to workshop technicians, maintenance teams and precision machinists. The short overall length and stable shank make it especially useful for operations requiring minimal deflection, such as jig and fixture work or when using a Hand Drill for controlled site repairs. 135° Point Angle: Faster Penetration and Better Centering in Hard Materials A 135° Point Angle helps reduce the tendency to wander on the surface of hard materials and shortens the initial penetration time compared with steeper points. This geometry lowers the cutting forces on the central tip and improves centring on Stainless Steel and other tough alloys, enabling more dependable starts and reducing the need for pilot operations in many cases. Standard Compliance and Practical Handling Notes Conforming to DIN 338 ensures consistent dimensions and interchangeability for short Twist Drills with cylindrical shank. The Standard Line manufacturing and the Fully Ground Shaft Execution ensure predictable performance across batches. For best results, pair the drill with appropriate coolant and moderate spindle speeds when working in high‑tensile steels; this preserves edge integrity and reduces the risk of chipping. Strong recommendation: choose the MetavCUT Twist Drill (Short Type N, HSS‑E) for demanding metal drilling tasks — for tailored advice or supplementary technical data contact METAV Werkzeuge by eMail: info@metav-werkzeuge.com, Tel: +49 2822 7131930, WhatsApp: +49 170 2837271 Technical Information Designation: Twist Drill Brand: MetavCUT SKU: 47090-FDA Diameter: 9 mm Point angle: 135° Type: Type N Execution: Short Colour: 5% cobalt-alloyed Material: HSS‑E Shaft execution: Fully ground Overall length: 125 mm Spiral length: 81 mm Model series: Standard Line Norm: DIN 338 For drilling machine: Drilling Machine (Hand Drill) Application: Drills for metal Packaging unit: 5 Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What are Twist Drills used for? The MetavCUT Twist Drill (Type N) is primarily used for machining high‑strength materials and larger drill diameters; its geometry allows straightforward regrinding and it withstands greater mechanical loads, making it a standard choice for robust Metalworking tasks. Which three drill types exist? Common categories are Metal drills, Wood drills and Stone/Concrete drills, and the MetavCUT Twist Drill belongs to the Metal drill group suited for ferrous and non‑ferrous Materials. Can the MetavCUT Twist Drill be used for wood? The MetavCUT Twist Drill can be used in Wood, but as a Metal drill it offers less guidance and a rougher finish than dedicated Wood drills; it is easier to resharpen and shows lower self‑feeding tendency compared with specialised wood brad point drills.
9mm HSS-G Twist Drill DIN 1869 ,extra long, bright finished - MetavCUT
Twist Drill by MetavCUT — 9 mm, 135° Tip, Extra Long, Bright Finished, HSS‑G, DIN 1869, Fully Ground Shank A Twist Drill designed for deep metal drilling with Drilling Machines and engineered for high precision and reduced feed force. Extra long design for deep drilling HSS‑G ground for faster metal cutting 135° tip geometry for hard materials Fully ground shank for high runout accuracy Conforms to DIN 1869 for demanding applications Faster drilling with lower feed force for efficient workflows The HSS‑G construction delivers up to 40% faster drilling while requiring 50% less feed force compared with conventional HSS drills, making it ideal where productivity matters. Designed as an extra long variant, this drill enables deeper hole depths and greater reach without sacrificing concentricity. For workshop and industrial use, the combination of high cutting speed and reduced operator exertion translates into measurable time savings and less operator fatigue. Reliable centring and clean holes even in tough alloys With a 135° tip angle and a ground flute geometry, this tool penetrates harder materials more effectively and reduces walking at the start of the hole. The CNC ground flutes provide sharp cutting edges and excellent runout accuracy, resulting in precise, burr‑reduced holes in Grauguss, legierten and unlegierten Stahl, and non‑ferrous metals. The geometry is optimised to support drilling in applications up to the material classes indicated by DIN 1869. Built for deep and difficult penetrations The extended overall length and a spiral length of 175 mm allow drilling where standard lengths fail, for example deep assemblies or awkward fixturing. The bright finished surface offers good chip evacuation characteristics in conjunction with appropriate coolant, while the fully ground shank ensures consistent clamping in chucks and reduced vibration. Use with a suitable Drilling Machine and controlled coolant flow for best results in prolonged or stationary operations. Who benefits and how to use it correctly Manufacturers, toolrooms and maintenance teams that require repeatable, precise holes in harder metals will value this design. For optimal life and performance, use stable fixturing, appropriate spindle speeds and coolant when working with high‑strength steels. Because ground HSS drills can be more brittle than rolled types, avoid excessive lateral loading and prefer stationary machine setups for deepest holes and continuous production runs. Strong recommendation: Choose the MetavCUT Twist Drill for precise deep‑hole metalworking — for technical advice or to confirm suitability for a specific application, contact METAV Werkzeuge for expert support via email info@metav-werkzeuge.com, phone +49 2822 7131930 or WhatsApp +49 170 2837271 Technical specifications Designation: Twist Drill Brand: MetavCUT SKU: 32090-FDA Diameter: 9 mm Tip Angle: 135° Execution: Extra long Total Length: 250 mm Spiral Length: 175 mm Material: HSS‑G Shank Execution: Fully ground Colour: Bright finished Application: Drills for metal For Drilling Machine: Drilling Machine Standard: DIN 1869 Model Series: Standard Line Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What is a Twist Drill used for and which materials suit this MetavCUT Twist Drill? The MetavCUT Twist Drill is primarily intended for drilling into metals; its HSS‑G composition and 135° tip make it especially suitable for alloyed and unalloyed steels, cast iron and non‑ferrous metals. Use in a properly set up Drilling Machine with cooling for best results. Which three general drill types exist? The three main drill categories are metal drills, wood drills, and stone/concrete drills; the MetavCUT Twist Drill belongs to the metal drill group and is optimised for metalworking tasks.
9mm HSS-G Twist Drill DIN 1869 ,extra long, bright finished - MetavCUT
Twist Drill — Twist Drill, Diameter 9 mm, 135° Tip, Extra Long, Bright Finished, HSS‑G, DIN 1869 The Twist Drill is an extra‑long HSS‑G drill bit for drilling machines, designed for deep metal drilling and precise holemaking in alloyed and unalloyed steels. Extra long design for deep drilling 9 mm diameter with 135° tip angle HSS‑G fully ground for precise bores Conforms to DIN 1869 for deep‑hole work Precision and material: ground HSS for clean metal holes The fully ground HSS‑G geometry delivers high concentricity and sharp cutting edges, producing clean, precise holes in metal. Grinding the flutes rather than rolling creates a sharper cutting profile, which reduces chatter and improves roundness when used with appropriate feed and coolant. This makes the bit particularly suitable for alloyed and unalloyed steel, cast iron and non‑ferrous metals where hole quality and dimensional accuracy are required. Deep drilling capability: extra length for difficult access With an extra long overall length and an extended spiral, this design allows drilling in deep parts or where access from the rear is restricted. The extended spiral assists chip evacuation during deeper cuts, reducing the risk of clogging. For tasks requiring long reach, the extra‑long execution provides the working length necessary without compromising guidance when used in a suitable drilling machine and with correct cooling. Tip geometry and performance: 135° for harder materials A 135° tip angle reduces the tendency to wander and shortens centring time on harder workpieces such as stainless steel. The larger tip angle reduces the aggressiveness of the lead, distributing cutting forces over a broader area and often requiring less feed force. For demanding materials, the combination of tip geometry and HSS‑G composition improves tool life when adequate coolant and a stable setup are used. Practical use and user group: suited for workshops and industrial settings This twist drill was developed for professional workshops and industrial users who need reliable deep drilling in metals. It is best applied in drilling machines under steady clamping and with cooling. Compared with rolled types, the ground version can be re‑sharpened more easily to renew cutting edges, making it advantageous for users who perform maintenance on tooling and value reproducibility and finish. Strong recommendation: Choose the MetavCUT Twist Drill in extra‑long HSS‑G execution for demanding deep metal drilling — for technical advice or to confirm suitability for a specific application, METAV Werkzeuge provides expert consultation: info@metav-werkzeuge.com, Phone +49 2822 7131930, WhatsApp +49 170 2837271 Designation: Twist Drill Brand: MetavCUT SKU: 33090-FDA Diameter: 9 mm Tip Angle: 135° Execution / Type: Extra Long Colour: Bright Finished Material: HSS‑G Shaft Execution: Fully Ground Spiral Length: 220 mm Overall Length: 320 mm Standard: DIN 1869 Application: Drills for Metal Model Series: Standard Line For Use In: Drilling Machine Manufacturer: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What is the MetavCUT Twist Drill used for? The MetavCUT Twist Drill is primarily applied for drilling high‑strength workpieces and larger diameters in metal; its extra‑long HSS‑G design and DIN 1869 specification make it suitable for deep drilling where extended reach and durable cutting performance are required. Which three drill types exist? Common categories are Metal drills, Wood drills and Masonry/Concrete drills; the MetavCUT Twist Drill belongs to the metal drill category and is optimised for metalworking tasks. For what is a Twist Drill mainly used? A Twist Drill is mainly used for machining high‑strength materials and larger hole diameters; its form allows straightforward resharpening and it withstands higher loads in demanding applications. Why are twist drills pointed? The point reduces the cross‑edge at the tip of the Twist Drill, significantly lowering friction and feed forces while improving centring in the workpiece; a pointed geometry therefore eases penetration and enhances accuracy.
9mm HSS-G Twist Drill DIN 1869 ,extra long, bright finished - MetavCUT
Twist Drill — Extra Long Twist Drill, 9 mm, 135° tip, HSS‑G, Bright Finished (MetavCUT) The Twist Drill is an extra‑long HSS‑G drill designed for deep metal drilling with a 9 mm diameter and a 135° tip for hard materials. Extra‑long design for deep, hard‑to‑reach holes 9 mm Diameter for precise metal drilling 135° Tip angle optimised for harder materials HSS‑G ground for fast, clean cuts DIN 1869 compliant for demanding deep‑hole work Precision and performance for deep metal holes The MetavCUT extra‑long HSS‑G twist drill combines a generous overall length with a long Spiral to enable deep‑reach drilling where standard lengths fall short. Thanks to the fully ground flute geometry, the bit produces very sharp cutting edges and high run‑out accuracy, which results in cleaner, more precise holes in metals. For workshop and industrial environments this means fewer re‑cuts, improved fit‑up of components and more predictable machining results under challenging conditions. Faster cutting with less feed force The ground HSS‑G material and optimised geometry allow up to 40% faster drilling and require up to 50% less feed force compared with conventional HSS drills. This makes the tool especially effective when working with alloyed and unalloyed steel, cast steel, cast iron and non‑ferrous metals. The 135° tip angle reduces initial cutting resistance and improves centring on harder materials, shortening set‑up time and increasing throughput on serial operations. Reliable choice for demanding standards and deep drilling Conforming to DIN 1869, this twist drill is built for deep‑hole applications and tougher conditions. The Spiral length of 280 mm and total length of 410 mm are tailored for situations that require extended reach without compromising hole quality. Because the flutes are formed by CNC grinding rather than rolling, users benefit from superior surface finish and dimensional accuracy—features that matter when subsequent machining or assembly demands tight tolerances. Practical workshop guidance and safe use When using this extra‑long Twist Drill in tougher materials, stationary mounting and adequate cooling are recommended to avoid brittle fracture and to extend tool life. The fully ground shank supports better clamping accuracy in chucks and collets, reducing vibration and ensuring concentricity. For operators less familiar with deep‑hole techniques, using modest spindle speeds, steady feed and cutting fluid will deliver the best balance between speed and tool life. Who benefits from this tool This drill is aimed at metalworkers, toolrooms and maintenance professionals who require extended reach and high‑quality holes in harder materials. Whether producing components in small series or performing repair work on assemblies where access is limited, the MetavCUT twist drill offers a practical combination of depth capability and metal‑cutting performance. Strongly recommended: the MetavCUT extra‑long HSS‑G Twist Drill for reliable deep metal drilling — for technical advice or application support contact METAV Werkzeuge; we provide comprehensive consultation and sample guidance via eMail: info@metav-werkzeuge.com, Phone: +49 2822 7131930, WhatsApp: +49 170 2837271 Technical data Designation: Twist Drill Brand: MetavCUT Model series: Standard Line Diameter: 9 mm Total length: 410 mm Spiral length: 280 mm Tip angle: 135° Material: HSS‑G Standard: DIN 1869 Execution: Extra long Colour: Bright finished Shaft finish: Fully ground Suitable for: Drilling Machine / Hand drill Application: Drills for metal Manufacturer: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What materials is the MetavCUT Twist Drill best suited for? The MetavCUT Twist Drill (extra‑long HSS‑G Twist Drill) is particularly suited to alloyed and unalloyed steel, cast steel, cast iron, sintered iron, malleable iron, non‑ferrous metals and hard plastics, offering robust performance where higher strength and precision are required. Is the MetavCUT Twist Drill suitable for very deep holes? Yes, the MetavCUT extra‑long Twist Drill is designed for deep holes: its extended overall length and the Spiral length make it suitable for deep‑reach applications, and compliance with DIN 1869 underlines its suitability for demanding drilling tasks. For what is a Twist Drill used? It is mainly used for machining high‑strength materials and large bore diameters. This design is easy to resharpen and withstands higher loads. Which three drill types exist? There are metal drills, wood drills and stone/concrete drills. Why are Twist Drills tipped/sharpened? Sharpening reduces the secondary cutting edge at the tip of the Twist Drill, lowering friction forces and thus requiring less feed force while improving centring in the workpiece. Can a metal Twist Drill be used to drill wood? A metal drill can be used in wood but gives poorer guidance and a less clean result; it is easier to regrind and has lower self‑feeding characteristics. For which depths is the Twist Drill the most used tool? A full‑bore hole is made with a Twist Drill. For diameters up to 20 mm and depths up to 100 mm, the Twist Drill is the most commonly used tool.
9mm HSS-G Twist Drill DIN 338 ,left cutting - MetavCUT
Twist Drill — Profi Line left-cutting HSS-G 9 mm, 135° (DIN 338) by MetavCUT The Twist Drill left-cutting HSS-G 9 mm is a metal drill bit designed for use in drilling machines and hand drills for efficient extraction and precise metal drilling. Left-cutting geometry for screw extraction and tough tasks 9 mm Diameter for standard metal drilling 135° Tip angle for harder materials like stainless steel HSS-G Material for wear resistance and durability Conforms to DIN 338 for short twist drills with cylindrical shank Superior Performance in Hard Materials thanks to the 135° Tip Angle The Profi Line short twist drill features a 135° tip angle, which reduces entry forces and shortens the pilot time when penetrating harder materials. This geometry is particularly advantageous for stainless steel and other high-strength alloys because it spreads cutting load and decreases the risk of tip wandering. The result is cleaner holes and improved centring in demanding Metal applications. One direct advantage for workshops is fewer rejects and less rework when machining tougher components. Left-cutting Design: Fast Extraction and Lower Feed Force A left-cutting grind means the bit is ground to cut when the spindle turns counterclockwise; this is ideal for removing broken or seized screws and studs. The MetavCUT left-cutting twist drill is optimised for such operations and, according to the manufacturer data, can achieve up to 40% faster drilling while requiring up to 50% less axial feed force compared with conventional HSS drills. For technicians, this translates into reduced operator strain and faster job turnaround when working on repair or disassembly tasks. Material and Standard: HSS-G and DIN 338 for Reliable Use Manufactured from HSS-G, this drill offers a balance of toughness and heat resistance suited for sustained metal cutting. The product is made to DIN 338, the standard describing short twist drills with a cylindrical shank; this ensures consistent shank dimensions, compatible fitting in standard chucks, and predictable performance across production workflows. For buyers this means reliable interchangeability in tool holders and consistent hole quality in serial work. Where this Drill Excels and Who Benefits Most This twist drill is aimed at professionals and maintenance technicians who work with both alloyed and unalloyed steels, cast steels, cast iron, sintered metals, non-ferrous metals and hard plastics. Its left-cutting version is especially useful in repair shops and assembly lines where removal of broken fasteners is frequent. The Profi Line series positions the bit as a practical choice for workshops that require a robust, short drill with dependable centring and reduced push-down effort. For demanding metalwork choose the MetavCUT Profi Line Twist Drill for reliable extraction and efficient drilling — METAV Werkzeuge offers expert advice and comprehensive support, contact via eMail: info@metav-werkzeuge.com, Phone: +49 2822 7131930, WhatsApp: +49 170 2837271 Technical Information Designation: Twist Drill (Spiralbohrer) Brand: MetavCUT SKU: 60090-FDA Diameter: 9 mm Tip Angle: 135° Execution: left-cutting (linksschneidend) For: Drilling Machine / Hand Drill Material: HSS-G Standard: DIN 338 Model Series: Profi Line Packaging unit: 5 Application: Drills for metal Manufacturer: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What is the Twist Drill used for? The MetavCUT Twist Drill is primarily applied to the machining of high-strength materials and larger drill diameters; it is especially suited for alloyed and unalloyed steel, cast steel, cast iron, sintered iron, malleable iron, non-ferrous metals and hard plastics. Its shape allows relatively simple resharpening while maintaining resistance under heavy loads. Which three drill types are there? Commonly distinguished drill types are metal drill bits, wood drill bits and masonry/concrete drill bits. The MetavCUT Twist Drill belongs to the metal drill bit group. Why are twist drills resharpened at the tip? Resharpening the tip of a twist drill reduces the cross-cut edge at the point. By regrinding the point, friction is significantly lowered and less feed force is required; at the same time the bit centres more reliably in the workpiece. Can a Twist Drill be used to drill wood? A metal twist drill such as the MetavCUT Twist Drill can be used in wood, but guidance is inferior and hole quality is usually less clean than with a dedicated wood bit. Metal bits are easier to resharpen and typically exhibit lower self-feeding tendencies. For which drilling depths is the Twist Drill most used? A through hole in solid material is typically produced with a twist drill. For diameters up to 20 mm and drilling depths up to 100 mm, the twist drill is the most commonly used tool. What is better, HSS or HSSE? The common belief that HSSE steels are always superior to standard HSS steels is not universally correct. When choosing between HSS and HSSE, evaluate whether the specific working conditions justify the higher acquisition cost of HSSE.
9mm HSS-G Twist Drill DIN 338 ,short, bright finished, Type N - MetavCUT
Twist Drill — MetavCUT Basic Line, 9 mm, 135° Tip, HSS‑G (Short, Bright Finished, DIN 338) The Twist Drill is a short HSS‑G metalworking drill designed for Drilling Machines and handheld use, offering high feed efficiency and stable performance in demanding steel applications. Short design for stable, precise drilling 9 mm diameter for common metalworking tasks 135° tip for improved centring in hard materials Fully ground shank for accurate seating in chucks Conforms to DIN 338 for short twist drills Faster penetration and reduced feed effort for hard metals The HSS‑G composition delivers a clear advantage: up to 40% faster drilling and roughly 50% less thrust compared with conventional HSS bits. For users working with alloyed and unalloyed Steel, Cast Steel, Gusseisen and hard plastics, this means fewer tool changes and smoother cycles. The 135° tip angle reduces the tendency to wander on tough surfaces and shortens dwell during initial engagement. This results in more efficient machining and less operator fatigue. Short geometry for superior stability and hole quality A short overall length and a spiral length of 81 mm minimise overhang and vibration, producing more consistent hole geometry under moderate cutting conditions. The fully ground shank ensures solid clamping in chucks and better concentricity, improving finish and reducing runout. Because the flute length and geometry follow DIN 338, workshop operators benefit from predictable behaviour when switching between comparable short twist drills. Built for metalworking workshops and maintenance tasks This Type N twist drill is the classic choice for metal applications and is optimised for Drilling Machines as well as robust handheld units. Its bright finished surface eases chip evacuation in many metals while remaining straightforward to resharpen when needed. For maintenance engineers, toolroom technicians and small fabrication shops, the combination of 9 mm diameter and short design strikes a balance between versatility and rigidity. Industry standard compliance delivers reproducible results Manufactured to DIN 338 specifications within the MetavCUT Basic Line, this twist drill follows proven dimensional and performance criteria for short cylinder‑shank bits. The Type N normal spiral provides a versatile chip geometry for a wide range of metallic materials. If uncertainty remains about the correct geometry or material choice for a specific application, the short tip geometry and HSS‑G grade allow straightforward regrinding while maintaining performance. We recommend the MetavCUT Twist Drill from the Basic Line for precision metalworking where stability and efficient penetration matter most — for technical questions or selection support contact METAV Werkzeuge for expert advice: info@metav-werkzeuge.com | +49 2822 7131930 | WhatsApp +49 170 2837271 Technical Data Bezeichnung: Twist Drill Marke: MetavCUT SKU: 27090-FDA Durchmesser: 9 mm Spitzenwinkel: 135° Typ: Type N Ausführung: short Farbe: bright finished Material: HSS-G Schaft Ausführung: fully ground Gesamtlänge: 125 mm Spirallänge: 81 mm Anwendung: Drills for metal Norm: DIN 338 Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What materials is the MetavCUT Twist Drill suitable for? The MetavCUT Twist Drill (Type N, HSS‑G) is primarily intended for metalworking; it performs well in alloyed and unalloyed Steel, Cast Steel, Gusseisen and certain hard plastics, offering reliable penetration and chip formation for these materials. How does the short design of the MetavCUT Twist Drill benefit workshop use? A short Twist Drill from MetavCUT reduces overhang and vibration, improving hole accuracy and concentricity; the compact geometry is especially helpful for precise operations and when working with harder materials where deflection must be minimised. For what is a Twist Drill used? A Twist Drill is mainly employed for machining high‑strength materials and larger drill diameters; this form is easy to resharpen and endures higher loads. Which three drill types exist? The main categories are Metal Drills, Wood Drills and Stone/Concrete Drills. Why are Twist Drills sharpened at the tip? Tip sharpening reduces the cross‑cut at the drill tip, lowering friction and thus reducing required feed force while improving centring in the workpiece. Can a Twist Drill be used to drill wood? A Metal Drill can be used in wood, but guidance and finish are inferior compared with dedicated wood drills. Metal drills are easier to resharpen and show less self‑feeding tendency. For which drilling depths is the Twist Drill most commonly used? Twist Drills are the standard choice for through‑hole drilling. For diameters up to 20 mm and depths up to 100 mm they are the most frequently used tool. Is HSS better than HSSE? The common belief that HSSE is always superior to HSS is incorrect; selection should consider the specific working conditions and whether the extra cost of HSSE is justified. Sind Sie sich nicht sicher, ob dieses Werkzeug Ihre Anforderungen erfüllt? Oder benötigen Sie ergänzende technische Daten? Kein Problem – wir stehen Ihnen gerne zur Verfügung. 📧 eMail: info@metav-werkzeuge.com ☎️ Telefon: +49 2822 7131930 ✔️ WhatsApp: +49 170 2837271
9mm HSS-G Twist Drill DIN 338 ,short, bright finished, Type N - MetavCUT
Twist Drill — Type N, 9 mm, 135° tip, short, bright finished, HSS-G, DIN 338 (MetavCUT) A short, precision Twist Drill Type N designed for metalworking with a 9 mm diameter and a 135° point angle for stable, clean drilling in hard materials. Short design for higher stability HSS‑G ground for fast, precise drilling 135° point for hard materials like stainless steel Conforms to DIN 338 for short cylindrical drills Fully ground shank for excellent concentricity Durable HSS‑G construction for reliable metalworking The HSS‑G material offers a balance of hardness and edge retention that benefits demanding metalworking tasks. Built as a ground High Speed Steel tool, this short drill delivers sharp cutting edges and high runout accuracy, which reduces burr formation and improves hole quality. For users who prioritize precision, the ground geometry translates into cleaner bores and fewer reworks, while the bright finished surface aids chip evacuation during cutting. Short design increases stability and precision A reduced overall length and a shorter Spiral length improve stiffness during drilling, so less bending occurs under load. This compact geometry is particularly useful when machining legiertem und unlegiertem Stahl and other hard metals, where a rigid tool axis is essential. The shorter overhang results in increased feed stability, enabling higher feed rates in many setups without sacrificing hole accuracy. 135° tip and Type N spiral for hard materials The 135° point angle is tailored to cut into harder materials with reduced tendency to wander at entry, making it suitable for stainless steel and other tougher alloys. As a Type N (normal spiral) configuration, the tool is optimized for metal drilling rather than soft substrates. For less experienced users: a larger tip angle decreases the initial cutting aggressiveness and improves centering, which helps when starting holes in tough components. Precise shank and DIN 338 compliance for machine use With a fully ground shank, the drill provides excellent concentricity and grip in standard drill chucks and toolholders, reducing runout and wear. Conformance to DIN 338 ensures standardized dimensions and compatibility with common tool setup procedures in production and workshop environments. These characteristics make the tool well suited to both stationary machines and portable drilling machines used in metal fabrication. Who benefits and recommended applications Mechanical workshops, toolrooms and production engineers working with steels, cast materials and non‑ferrous metals will find the short Twist Drill especially advantageous for precision holemaking. Its properties support drilling in components where surface finish and positional accuracy matter. For simple explanations: HSS‑G denotes a ground High Speed Steel drill, Type N indicates the classic metal spiral, and the 135° tip suits harder substrates. Strong recommendation: For precision metal drilling choose the MetavCUT short Twist Drill Type N with HSS‑G ground geometry — METAV Werkzeuge offers expert advice and technical support if needed. If unsure whether this tool meets specific requirements or if additional technical data is required, please contact us — 📧 info@metav-werkzeuge.com | ☎️ +49 2822 7131930 | ✔️ WhatsApp +49 170 2837271 Designation: Twist Drill Brand: MetavCUT SKU: 45090-FDA Diameter: 9 mm Point angle: 135° Type: Type N Execution: short Overall length: 125 mm Spiral length: 81 mm Shank execution: fully ground Material: HSS-G Finish: bright finished For drilling machine: Drilling Machine Application: Drills for metal Model series: Standard Line Norm: DIN 338 Colour: bright finished Manufacturer: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What is a Twist Drill used for and which materials suit the MetavCUT Type N drill? The Twist Drill by MetavCUT, Type N, is primarily used for drilling metal; it is ideal for legiertes und unlegiertes Stahl, Gussstahl, Gusseisen and non‑ferrous metals. The Type N spiral and HSS‑G ground geometry ensure reliable cutting in harder materials and give good hole quality in workshop and production settings. Which three drill types exist and where does the MetavCUT Twist Drill fit? Three common drill types are metal drills, wood drills and masonry/concrete drills. The MetavCUT Twist Drill is a metal drill (Type N) and is specifically engineered for use in metalworking rather than for wood or stone. Why is the tip of a Twist Drill sharpened and how does that help in practice? The tip sharpening reduces the cross‑cut edge at the drill point, lowering friction and required feed force. For the MetavCUT Twist Drill Type N this means easier entry, better centering and reduced heat generation, resulting in cleaner holes and longer tool life when combined with appropriate cooling. Can the MetavCUT Twist Drill be used for drilling wood? A metal drill such as the MetavCUT Twist Drill can be used in wood, but it will usually offer less guidance and a rougher finish than a dedicated wood drill. Metal drills are easier to resharpen and exhibit less self‑feeding, so they may require more careful positioning when used in timber.
9mm HSS-G Twist Drill DIN 338 ,short, bright finished, Type N - MetavCUT
Geringe Auskraglänge und geschliffene HSS-G-Geometrie sorgen für präzise, vibrationsarme Bohrungen in Stahl und Guss; der 135° Spitzenwinkel erleichtert das Anbohren harter Werkstoffe und reduziert das Ausbrechen. Nutzen Sie die Kombination aus Stabilität, schnellerer Vorschubrate und hoher Rundlaufgenauigkeit, und ordern Sie den Bohrer direkt über Metav als verlässlichen Partner. Spiralbohrer 9 mm HSS-G (kurz) – MetavCUT Profi Line Spiralbohrer 9 mm HSS-G (kurz) – MetavCUT Profi Line eignet sich für präzise Metallbohrungen an stationären und handgeführten Maschinen und wurde nach DIN 338 für kurze Spiralbohrer ausgelegt. Kurze Ausführung für erhöhte Stabilität HSS-G geschliffen für saubere Bohrlöcher 135° Spitzenwinkel: besseres Anbohren von Edelstahl Zylinderschaft, passend für Handbohrmaschine DIN 338 Klassifikation, Profi Line Qualität Präzise Bohrleistung für harte Werkstoffe Die kurze Bauform reduziert die Auskraglänge und erhöht so die Stabilität beim Bohren. Bei gleicher Bohrungsgröße führt die verringerte Hebellänge zu weniger Vibrationen und verbessertem Rundlauf, was saubere und maßhaltige Bohrlöcher zur Folge hat. Die geschliffene HSS-G-Geometrie sorgt für sehr scharfe Schneiden und ermöglicht ein bis zu 40 % schnelleres Bohren bei gleichzeitig 50 % geringerer Anpresskraft gegenüber herkömmlichen HSS-Ausführungen, besonders in legierten und unlegierten Stahlgüten. Passgenau für Werkstatt und Montage Diese Ausführung wurde für den Einsatz an stationären Bohrmaschinen und für handgeführte Geräte konzipiert. Die Kombination aus Zylinderschaft und kurzer Gesamtlänge macht den Bohrer kompatibel mit typischen Spannfuttern und erhöht die Sicherheit bei der Anwendung. Anwender in Werkstatt, Montage und Instandhaltung profitieren von der einfachen Handhabung und der schnellen Verfügbarkeit des passenden Werkzeugs für Serien- und Einzelteile. Materialwahl, Geometrie und Normen für professionelle Ansprüche Der Bohrer besteht aus HSS-G (Schnellarbeitsstahl, geschliffen) und entspricht der DIN 338, die kurze Spiralbohrer mit Zylinderschaft klassifiziert. Die geschliffene Fertigung bringt sehr hohe Rundlaufgenauigkeit und scharfe Schneiden, wodurch besonders präzise Bohrungen in Gussstahl, Gusseisen und Nichteisenmetallen möglich sind. Hinweis: Geschliffene HSS-Werkzeuge können spröder sein; Kühlung und stationären Einsatz erhöhen die Standzeit. Zielgruppen und typische Einsatzbereiche Entwickelt für Anwender, die präzise Metallbohrungen benötigen: Industrie, Fachbetrieb und anspruchsvolle Heimwerker. Der Typ N mit Normalspirale ist speziell für Metallbearbeitungen wie Stahl, Temperguss und Hartkunststoff ausgelegt. Für sehr tiefe Löcher oder hochgehärtete Stähle sind andere Werkzeuge sinnvoll; für standardmäßige Bohrungen bis zu mittlerer Tiefe bietet dieses Produkt jedoch ein hervorragendes Verhältnis aus Präzision und Wirtschaftlichkeit. Empfehlung: Für präzise Metallbohrungen die Profi Line von MetavCUT wählen und technische Beratung direkt bei Metav anfordern per eMail info@metav-werkzeuge.com oder Telefon +49 2822 7131930 Produktmerkmale Artikelnummer: 48090-FDA Marke: MetavCUT Serie: Profi Line Bezeichnung: Spiralbohrer Fakten Durchmesser: 9 mm Gesamtlänge: 125 mm Spiralänge: 81 mm Spitzenwinkel: 135° Verpackungseinheit: 5 Besonderheiten Material: HSS-G (Schnellarbeitsstahl, geschliffen) Schaft Ausführung: geschliffen (vollständig geschliffener Zylinderschaft) Norm: DIN 338 (kurze Spiralbohrer mit Zylinderschaft) Typ: Typ N (Normalspirale, geeignet für Metall) Ausführung: kurz (reduzierte Auskraglänge) Farbe: blank (bright finished) Für Bohrmaschine: Handbohrmaschine Hersteller: MetavCUT FAQ Welche Werkstoffe kann ich mit diesem Spiralbohrer bearbeiten? Der MetavCUT Spiralbohrer in HSS-G ist ausgelegt für legierten und unlegierten Stahl, Gussstahl, Gusseisen, Sintereisen, Temperguss, Nichteisenmetalle und Hartkunststoff; für sehr weiche Werkstoffe kann eine andere Bohrersorte sinnvoll sein. Ist dieser Bohrer für Handbohrmaschinen geeignet? Ja, der Zylinderschaft und die kurze Ausführung machen den Spiralbohrer kompatibel mit gängigen Spannfuttern von Handbohrmaschinen sowie stationären Bohrmaschinen. Warum ist die geschliffene Ausführung vorteilhaft? Geschliffene HSS-G-Bohrer bieten hohe Rundlaufgenauigkeit und scharfe Schneiden, was zu saubereren Bohrlöchern führt; der MetavCUT Profi Line nutzt diese Eigenschaft für präzise Metallbearbeitung. Welchen Vorteil bringt der 135° Spitzenwinkel? Der 135° Spitzenwinkel erleichtert das Anbohren harter Werkstoffe und verringert das Wanderverhalten beim Ansetzen, was ein kontrollierteres Einstechen und weniger Ausbrechen bewirkt. Für welche Art von Produktion ist dieser Bohrer nicht ideal? Für sehr tiefe Bohrungen (deutlich über das 5-fache des Durchmessers) oder großserielle Bearbeitung von hochgehärtetem Stahl ist meist ein Vollhartmetallwerkzeug wirtschaftlicher als der HSS-G Spiralbohrer. Welche Normen und Serienbezeichnung hat der Bohrer? Der Bohrer trägt die DIN 338 Klassifikation und gehört zur Profi Line von MetavCUT, Artikelnummer 48090-FDA.
9mm HSS-G Twist Drill DIN 338 ,short, TIN-coated - MetavCUT
Twist Drill — Short HSS-G Drill, 9 mm, 118° point, TIN-coated, DIN 338, fully ground, MetavCUT A short Twist Drill designed for precise metal drilling with Drilling Machines Short design for increased stability and precision TIN-coated surface for reduced wear and friction HSS-G fully ground for faster drilling and clean holes 118° point angle for easy centring in softer metals Conforms to DIN 338 for consistent manufacturing quality Durable HSS-G Construction for Longer Tool Life The HSS-G base material combined with a TIN-coated surface delivers extended lifetime when working with metallic materials. This composition reduces surface wear and friction, so heat buildup is minimised during continuous drilling. The coating supports improved tool life particularly under intermittent cooling, while the substrate material retains cutting edge stability for demanding machining tasks. Short Design and Fully Ground Geometry for Precise Results A shorter overall length reduces overhang and increases stability, which directly improves concentricity and reduces vibration during drilling. The fully ground flute geometry creates sharper cutting edges, enabling up to faster penetration with lower feed forces compared to rolled types. The 118° point angle favours centring and controlled entry in softer metals and certain non-ferrous alloys while still offering reliable starts on slightly curved surfaces. Optimised for Metalworking and Professional Use Designed for use with Drilling Machines, this tool excels in machining alloyed and unalloyed steel, Tempered Cast Iron, Gusseisen, Sintered Iron, Copper, Bronze and hard plastics. Workshops and maintenance professionals benefit from consistent hole quality and reduced rework. The tool’s characteristics make it particularly suitable for precision tasks where minimized runout and reproducible hole tolerances matter. DIN 338 Standard and Practical Handling Advice Manufactured to DIN 338, the tool follows industry definitions for short Twist Drills with Cylindrical Shanks. Being ground rather than rolled results in sharper edges and higher runout accuracy, but also a slightly increased susceptibility to fracture under improper handling. Use appropriate coolant for extended tool life and prefer stationary or well-supported setups to exploit the drill’s precision advantages. Strongly recommend MetavCUT’s short TIN-coated HSS-G Twist Drill for demanding metalworking tasks — for expert advice and application support contact METAV Werkzeuge: 📧 info@metav-werkzeuge.com | ☎️ +49 2822 7131930 | ✔️ WhatsApp +49 170 2837271 — METAV Werkzeuge offers extensive and competent consultation for technical queries and product selection Bezeichnung: Twist Drill Marke: MetavCUT SKU: 28090-FDA Durchmesser: 9 mm Spitzenwinkel: 118° Gesamtlänge: 125 mm Spirallänge: 81 mm Ausführung: short Schaft Ausführung: fully ground Farbe / Beschichtung: TIN-coated Material: HSS-G Norm: DIN 338 Für Bohrmaschine: Drilling Machine Anwendung: Drills for metal Modellserie: Basic Line Hersteller: MetavCUT Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What is the MetavCUT Twist Drill used for? The MetavCUT Twist Drill is mainly applied to the machining of high-strength materials and larger drill diameters; its short design and robust geometry make it suitable for demanding metalworking tasks. The tool’s shape allows relatively easy resharpening and it withstands considerable loads while delivering clean, precise holes. Which three drill types exist? The common classification names three main categories: Metal drills, Wood drills and Masonry/Concrete drills. The MetavCUT Twist Drill belongs to the metal drill group and is optimised for the properties and requirements of metallic materials.
9mm HSS-G Twist Drill DIN 338 ,short, TIN-coated, Type N - MetavCUT
Twist Drill — Short HSS-G Type N, 9 mm, 135°, TiN-coated, DIN 338 The Twist Drill is a short HSS-G metalworking drill bit (Type N) designed for precision drilling in hard materials and optimised for use in drilling machines. Short design for higher stability TiN-coated for extended tool life Fully ground shank for cleaner holes 135° tip for hard metals and stainless steel Conforms to DIN 338 for short drill bits Durable Material and Coating for Long Service Life The short HSS-G construction combined with the TiN-coated surface reduces friction and wear during metalworking, which translates into a significantly longer lifetime under continuous use. With a 9 mm diameter and a flute length of 81 mm, this bit is especially suited for alloyed and unalloyed steel, cast iron, sintered iron, nickel silver, copper, bronze and hard plastics. The TiN layer lowers surface temperature and, when used with appropriate cooling, decreases abrasive wear and maintains cutting performance over prolonged operations. Stable Short Design for Precise, Efficient Drilling Thanks to the reduced overhang of the short execution, this Twist Drill provides superior stability and resists bending under load, enabling more accurate hole positions and improved concentricity. The fully ground geometry yields sharp cutting edges and high running accuracy, allowing up to 40% faster penetration and requiring about 50% less feed force compared with conventional HSS drills. These advantages make it a reliable choice for demanding production and workshop environments where precision and throughput matter. Optimised Tip Geometry and Suitable Applications The 135° point angle is tailored for harder materials and stainless steel: it shortens the initial penetration time and improves centring on tough surfaces. As a Type N normal-spiral bit, the tool excels at general metal drilling tasks and is intended primarily for use with drilling machines. Typical fields of application include maintenance, toolrooms and manufacturing where metals such as steel, cast components and non-ferrous alloys must be drilled with repeatable quality. Compliance, Manufacturing and Best Practice Manufactured according to DIN 338 as a short, cylindrical-shank Spiral Drill, this product is produced as a ground (HSS-G) variant, which implies CNC-ground flutes for sharp edges and precise geometry. Ground drills generally offer cleaner holes and better accuracy than roll-formed types, though they can be somewhat more brittle and therefore are recommended for use with suitable coolant and in predominantly stationary mounting conditions. For optimal results, pair the bit with controlled speeds, adequate coolant and a solid clamping system. For precision metalworking, choose the MetavCUT Twist Drill Type N with TiN coating — for technical advice or to confirm suitability, METAV Werkzeuge provides expert consultation via email info@metav-werkzeuge.com, by phone +49 2822 7131930 or WhatsApp +49 170 2837271 Designation: Twist Drill Brand: MetavCUT SKU: 46090-FDA Diameter: 9 mm Flute Length (Spirallänge): 81 mm Total Length (Gesamtlänge): 125 mm Point Angle (Spitzenwinkel): 135° Type: Type N Execution (Ausführung): short Shank Finish (Schaft-Ausführung): fully ground Coating (Farbe): TiN-coated Material: HSS-G Standard (Norm): DIN 338 Application: Drills for metal / Bohrer für Metall Intended Machine (Für Bohrmaschine): Drilling Machine / Handbohrmaschine Model Series (Modellserie): Standard Line Manufacturer: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What is the Twist Drill (MetavCUT, Type N) mainly used for? The MetavCUT Twist Drill Type N is primarily applied to machining high-strength materials and larger hole diameters; it performs well on alloyed and unalloyed steels and similar metals. Its form allows easier regrinding and it endures considerable loads, making it suitable for demanding metalworking tasks. Which three drill types exist? The main categories are Metal drills (such as the MetavCUT Twist Drill), Wood drills and Masonry/Concrete drills. Each type is optimised in geometry and material for its intended substrate.
9mm HSS-G Twist Drill DIN 338 ,short, TIN-coated, Type N - MetavCUT
Twist Drill Profi Line — 9 mm, 135° · Type N · TIN-coated · Short · HSS‑G · DIN 338 The Twist Drill Profi Line is a short Type N drill designed for precision metalworking with Drilling Machines and Hand Drills. Short design for higher stability and precision TIN-coated HSS‑G for extended tool life Fully ground shank for fast, low-force drilling Optimised 135° tip for hard metals Conforms to DIN 338 for reliable quality Precision and productivity for metalworking Kurz-design drills like the Twist Drill Profi Line combine a reduced overhang with a robust geometry, resulting in higher Stability and less tendency to deflect when drilling. The HSS‑G material paired with a TIN‑coating reduces friction and wear, so holes in alloyed and unalloyed steel, cast components and non‑ferrous metals are produced with consistent accuracy. This yields a measurable time advantage in series work and minimises rework. Less effort, faster penetration with fully ground geometry A fully ground flute and refined cutting geometry ensure the drill requires up to 50% less feed force and can cut faster, especially in demanding materials. The 135° point angle shortens the initial entry time on hard materials such as stainless steel, while the precise tip improves centring. For users, this means easier handling on handheld machines and more predictable results on stationary Drilling Machines. Robust short format tailored to demanding tasks The short overall length (125 mm) and spiral length (81 mm) make this drill particularly suited to operations where rigidity is decisive. The Type N normal helix is the classic choice for metalworking, offering reliable chip evacuation across a broad range of alloys. Operators benefit from cleaner holes and less vibration, which is especially valuable when drilling tougher materials or when hole quality is critical. Practical explanation of key terms The designation HSS‑G indicates a High Speed Steel drill produced by grinding (G = ground), which provides very sharp cutting edges and excellent concentricity. TIN‑coated refers to a thin layer of Titanium Nitride that increases surface hardness and reduces adhesive wear. DIN 338 classifies short twist drills with cylindrical shanks and ensures interchangeability and consistent dimensions across manufacturers. Strong recommendation: For demanding metal drilling choose the MetavCUT Profi Line Twist Drill — for advice or to confirm suitability contact METAV Werkzeuge: 📧 info@metav-werkzeuge.com ☎️ +49 2822 7131930 ✔️ WhatsApp +49 170 2837271 Designation: Twist Drill / Spiralbohrer Marke: MetavCUT SKU: 41090-FDA Diameter: 9 mm Point Angle: 135° Type: Type N Execution: Short Colour/Coating: TIN-coated Material: HSS‑G Shank Execution: Fully ground Spiral Length: 81 mm Overall Length: 125 mm For Drilling Machine: Drilling Machine / Hand Drill suitability indicated Norm: DIN 338 Series: Profi Line Application: Drills for metal Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What is the MetavCUT Profi Line Twist Drill used for? The MetavCUT Profi Line Twist Drill is primarily used for machining high‑strength materials and larger diameters; it is especially effective when drilling alloyed or unalloyed steel and other metals where a short, rigid tool is required. Its construction allows it to withstand higher loads and deliver precise hole geometry. Which three drill types exist? Generally, three common drill categories are distinguished: Metal Drills, Wood Drills and Masonry/Concrete Drills. The MetavCUT Profi Line Twist Drill belongs to the Metal Drill category and is optimised for metalworking tasks. Why are twist drills re‑pointed? Re‑pointing reduces the cross‑cut at the tip of the Twist Drill, significantly lowering friction and therefore the required feed force; at the same time the tip centres better in the workpiece, improving hole accuracy. Can a metal drill be used for wood? A Metal Drill such as the MetavCUT Profi Line can be used in wood, but guidance and hole finish are inferior compared with dedicated wood drills. Metal drills are easier to re‑sharpen and have less self‑pulling action, which can be an advantage in some manual operations. For which drilling depths is the Twist Drill most commonly used? A through‑hole in solid material is typically executed with a Twist Drill. For diameters up to 20 mm and drilling depths up to 100 mm, the Twist Drill is the most frequently used tool, offering efficient chip removal and reliable performance. Is HSS or HSSE better? The common assumption that HSSE alloys are categorically superior to HSS is not always correct. Selection should be based on working conditions: HSSE can offer advantages in specific high‑speed or abrasive situations, but the higher purchase cost must be justified by the application. Are you unsure whether this tool meets your requirements or need additional technical data? METAV Werkzeuge offers comprehensive, expert consultation — contact us by email at info@metav-werkzeuge.com, by phone at +49 2822 7131930 or via WhatsApp at +49 170 2837271.
9mm HSS-G Twist Drill DIN 338 - MetavCUT
Twist Drill — Metal Drill HSS‑G, Ø 9 mm, 135° Point, Spezial, DIN 338, with multi‑bevel cutting edge and triangular shank, MetavCUT The Twist Drill HSS‑G metal drill is designed for fast, precise holes in steel and other hard materials, suitable for hand and stationary drilling machines. Fast drilling: up to 40% quicker than standard HSS Requires 50% less feed force 135° point for harder materials 3‑flat shank for secure grip in cordless drills Conforms to DIN 338 for short twist drills Faster metalworking with less effort This HSS‑G tool delivers a measurable productivity gain thanks to a specially ground geometry that enables up to 40% faster drilling while needing 50% less feed force than conventional HSS drills. The result is reduced operator fatigue and higher throughput in repetitive tasks. For workshops and industrial users who value cycle time, the shortened drilling time translates directly into improved efficiency and lower labour costs per hole without compromising hole quality. Cleaner entry and reliable centring in hard materials The 135° point is optimised for harder workpiece materials such as stainless steel and tempered alloys; it reduces wandering at the start of the hole and shortens the required plunge distance. By decreasing the chisel edge width, the point geometry lowers friction and cutting forces, which helps produce burr‑reduced, clean hole edges. For users unfamiliar with tip angles: a larger point angle typically penetrates harder materials more easily and provides better centring. Secure clamping and compatibility for hand tools The design with a triangular shank (3‑flat shank) ensures slip‑free engagement in chucks of cordless and hand drills, improving torque transfer and reducing slippage during exertion. Conformance to DIN 338 classifies this as a short twist drill with a cylindrical shank made of high‑speed steel, so it fits standard toolholders and is suitable for both mobile and stationary applications. METAV Werkzeuge offers expert consultation if there are questions about drill retention or machine compatibility. Tailored for demanding applications and varied materials Manufactured from HSS‑G, this Rapid‑type drill is suitable for a broad spectrum of materials including alloyed and unalloyed steels, cast and temper‑cast steels, non‑ferrous metals, hard plastics and also for occasional use in wood. Its geometry focuses on reliable performance in metalworking environments; the short configuration is particularly advantageous where rigidity and minimal runout are required. For precision shops, maintenance teams or professionals, this tool combines robustness with straightforward resharpening. Strong recommendation: For professionals seeking faster, cleaner holes in tough materials, choose the MetavCUT HSS‑G Twist Drill — METAV Werkzeuge provides comprehensive technical advice and support via email, phone and WhatsApp: info@metav-werkzeuge.com | +49 2822 7131930 | WhatsApp +49 170 2837271 Designation: Twist Drill Brand: MetavCUT SKU: 55090-FDA Diameter: 9 mm Point angle: 135° Spiral length: 81 mm Total length: 125 mm Shaft execution: with multi‑bevel cutting edge and triangular shank Model series: Spezial Material: HSS‑G Standard: DIN 338 Application: Drill for metal Suitable for: Drilling Machine (hand drill) Packaging unit: 5 Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ For what is a Twist Drill used? The MetavCUT Twist Drill is primarily applied to the machining of high‑strength materials and larger bore diameters; its shape is easy to regrind and it withstands greater loads, making it ideal for demanding metalworking operations. Which three drill types exist? Common drill types are metal drills, wood drills and stone/concrete drills, and the MetavCUT Twist Drill belongs to the metal drill category tailored for metal machining. Why are Twist Drills pointed? Pointing reduces the chisel edge at the tip of the Twist Drill, which significantly lowers friction and therefore requires less feed force; at the same time the point improves centring of the drill in the workpiece. Can a Twist Drill be used to drill wood? A metal drill such as the MetavCUT Twist Drill can be used in wood, but guidance is inferior and the finish is less clean; however these drills are easier to resharpen and show less self‑feed. At which drilling depths is the Twist Drill most used? A full‑bore hole is often executed with a Twist Drill. For diameters up to 20 mm and drilling depths up to 100 mm the Twist Drill is the most commonly used tool. What is better, HSS or HSSE? The general belief that HSSE steels are inherently superior to normal HSS is incorrect; when choosing between HSS and HSSE for a MetavCUT Twist Drill, assess working conditions carefully to determine whether the higher purchase cost of HSSE is justified.
9mm HSS-G Twist Drill DIN 340 ,long, bright finished - MetavCUT
MetavCUT Twist Drill — Twist Drill, 9 mm, 135° tip, Long, Bright finished, HSS‑G, DIN 340 The MetavCUT Twist Drill is a long HSS‑G Twist Drill engineered for deep, precise metal drilling in demanding applications with a 9 mm diameter and a 135° tip. Long HSS‑G Twist Drill for deep holes 9 mm diameter for precise metal drilling 135° tip for hard materials like stainless steel Fully ground shank for high runout accuracy Conforms to DIN 340 for deep hole performance High cutting performance for tough metals Designed to handle challenging materials, this long HSS‑G Twist Drill excels in drilling legierte und unlegierte Stahl grades and cast irons. The larger 135° tip angle reduces entry forces for harder workpieces and improves centring, while the long flute length allows access to recessed holes. Users benefit from faster advance and reduced effort, since the ground geometry promotes a sharper cutting edge and cleaner chip removal. Precise geometry for accurate bores A fully ground shaft and CNC‑ground flutes ensure high runout accuracy and consistently round holes, which is critical when machining components that require tight tolerances. The ground manufacturing method yields very sharp edges and precise tolerance control; however, the harder geometry is best used with appropriate feed, cooling and, for portable setups, cautious handling to avoid brittle breakage. Practical advantages in workshop and production Because the long variant follows DIN 340, it is suited for deeper bores, bushings and situations with limited accessibility. The bright finished surface aids visual inspection and reduces initial friction during entry. For metalworking tasks in small series or repair work the tool reduces rework thanks to cleaner holes, making it an efficient choice where reliability and repeatability matter most. Who benefits and how to use it safely Engineers, toolroom technicians and maintenance professionals profit from the combination of HSS‑G hardness and long design when working on automotive, mechanical and maintenance applications. When using this Twist Drill in stationary machines, apply cutting fluid and moderate speed for best life expectancy. For handheld Drilling Machines, maintain firm guidance and lower advance rates to minimise breakage risk. We recommend the MetavCUT long HSS‑G Twist Drill for demanding deep metal bores — for personalised advice, drill parameter recommendations or further technical data contact METAV Werkzeuge: info@metav-werkzeuge.com, phone +49 2822 7131930 or WhatsApp +49 170 2837271 Designation: Twist Drill Brand: MetavCUT SKU: 53090-FDA Diameter: 9 mm Total length: 175 mm Spiral length: 115 mm Tip angle: 135° Material: HSS‑G Execution: Long Colour: Bright finished Shank execution: Fully ground Standard: DIN 340 For drilling machine: Drilling Machine Application: Drills for metal Model series: Standard Line Packaging unit: 5 Manufacturer: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What is the MetavCUT Twist Drill best used for? The MetavCUT Twist Drill is primarily intended for metalworking and is applied for drilling in high‑strength and cast materials where long, stable bores are required; it is especially suitable for deep holes and hard materials. Can the MetavCUT Twist Drill be re‑sharpened and reused? Yes, the MetavCUT Twist Drill made of HSS‑G can be re‑sharpened by grinding; attention should be paid to preserving the original tip angle and flute geometry to maintain performance. For what are Twist Drills used? The MetavCUT Twist Drill is mainly used when machining high‑strength materials and larger diameters; its form is relatively easy to re‑grind and it stands up to higher loads. Which 3 drill types exist? The main categories are metal drills, wood drills and stone/concrete drills; the MetavCUT Twist Drill belongs to the metal drill type. Why are Twist Drills pointed? The point grind reduces the cross‑cut at the tip of the MetavCUT Twist Drill, lowering friction and required feed forces while improving centring accuracy in the workpiece. Can you drill wood with a Twist Drill? A metal drill such as the MetavCUT Twist Drill can be used in wood, but guidance and finish are inferior compared with dedicated wood drills; metal drills are easier to re‑sharpen and have less self‑feed. At which drilling depths is the Twist Drill most used? Solid drilling for diameters up to around 20 mm and depths up to 100 mm is the most frequent use case; the MetavCUT Twist Drill is a common choice for such through‑holes and deep bores. What is better, HSS or HSSE? Choosing between HSS and HSSE depends on working conditions; the common assumption that HSSE is universally superior is incorrect — evaluate whether the application justifies the higher cost relative to the actual material and speed demands.
9mm Spiralbohrer, 118° Spitzenwinkel, HSS, Morsekegel, rollgewalzt, 87mm Spirallänge - MetavCUT
Profitieren Sie von der Kombination aus HSS-Material und rollgewalzter Fertigung für erhöhte Zähigkeit und verringertes Bruchrisiko bei Standardbohrungen. Nutzen Sie die Morsekegelschaft für sichere Drehmomentübertragung bei Ständerbohrmaschinen. Bestellen Sie den Bohrer direkt über Metav oder fragen Sie unsere Beratung an. Spiralbohrer von MetavCUT — Standard Line (SKU 54090-FDA) Der Spiralbohrer für Metall mit rollgewalzter HSS-Ausführung und Morsekegelschaft bietet belastbare Leistung für Werkstatt und Maschinenpark. HSS rollgewalzt für erhöhte Zähigkeit Morsekegelschaft für sichere Drehmomentübertragung Norm DIN 345 für standardisierte Einsätze 9 mm Durchmesser, 168 mm Gesamtlänge Spitzenwinkel 118° für leichtes Eindringen Haltbarkeit durch Materialwahl und Fertigungsverfahren für robuste Einsätze Die HSS-Legierung in Kombination mit der rollgewalzten Herstellung macht den Bohrer zäher und bruchsicherer als geschliffene Alternativen in vergleichbaren Einsatzbereichen. Diese Fertigungsweise reduziert das Bruchrisiko bei Durchmessern unter 6 mm, bleibt aber auch bei 9 mm robust, wenn es um Bohrungen in legierten und unlegierten Stahl, Guss und Nichteisenmetallen geht. Daraus ergibt sich ein klarer Vorteil in Arbeitsumgebungen, in denen Standzeit und Wirtschaftlichkeit zählen. Sichere Aufnahme und Kraftübertragung für stationäre Maschinen Für den Einsatz in Ständerbohrmaschinen und ähnlichen stationären Maschinen sorgt die Morsekegelschaft für selbsthemmende Verbindung und präzise Drehmomentübertragung. Der Bohrer eignet sich besonders dort, wo hohe Kräfte übertragen werden müssen und ein fixer Sitz in der Aufnahme gefordert ist. Durch die Kombination aus Schaftform und Konstruktion lassen sich Wiederholbohrungen mit stabiler Laufruhe und reduziertem Rundlaufrisiko erreichen. Einsatzbereich und Anwendungsempfehlungen für Metallbearbeitung Der Bohrer ist ausgelegt für allgemeine Metallbohrung bis etwa 900 N/mm² Festigkeit, einschließlich Grauguss, Temperguss und Sintereisen. Beim Bohren in dünnen Blechen empfiehlt sich Vorzentrierung, bei dichten oder zähen Werkstoffen Kühlschmierstoff zu verwenden, um Spananhäufung zu vermeiden. Der Spitzenwinkel 118° erleichtert das Eindringen in weichere Materialien und unterstützt sauberes Ansetzen auf gewölbten Flächen. Präzision und Handling im Arbeitsalltag Mit einer Spirallänge von 87 mm und einer Gesamtlänge von 168 mm bietet der Bohrer guten Spantransport und Reichweite für viele Standardaufgaben. Die DIN 345-Konformität sichert Kompatibilität mit gängigen Normen im Maschinenbau und Instandhaltung. Anwender erhalten damit ein Werkzeug, das bekannte Anforderungen in Werkstatt und Fertigung zuverlässig abdeckt, ohne aufwendige Spezialspannmittel zu benötigen. Setzen Sie auf die MetavCUT Standard Line für belastbare Metallbohrungen und ordern Sie den Spiralbohrer direkt über Metav oder kontaktieren Sie die Fachberatung per eMail unter info@metav-werkzeuge.com bzw. telefonisch Produktmerkmale Artikelnummer: 54090-FDA Marke: MetavCUT Serie: Standard Line Bezeichnung: Spiralbohrer Daten Durchmesser: 9 mm Gesamtlänge: 168 mm Spirallänge: 87 mm Spitzenwinkel: 118° Verpackungseinheit: 1 Besonderheiten Material: HSS Ausführung: rollgewalzt Schaftausführung: Morsekegel — selbsthemmend, hohe Drehmomentübertragung Norm: DIN 345 Farbe: schwarz FAQ Welche Materialien lassen sich mit dem Spiralbohrer bearbeiten? Der MetavCUT Spiralbohrer aus der Standard Line (SKU 54090-FDA) eignet sich für Stahl, legierte und unlegierte Werkstoffe, Guss und Nichteisenmetalle sowie Kunststoffe, solange die Festigkeit 900 N/mm² nicht deutlich überschreitet. Ist die Morsekegelschaft für Ständerbohrmaschinen geeignet? Ja, die Morsekegelschaft des MetavCUT Spiralbohrers bietet eine selbsthemmende Aufnahme, die für Ständerbohrmaschinen und Maschinen mit entsprechender MK-Aufnahme optimale Kraftübertragung ermöglicht. Wie unterstützt die rollgewalzte Fertigung die Einsatzdauer? Die rollgewalzte Herstellung macht den HSS-Bohrer zäher und reduziert das Bruchrisiko insbesondere bei kleineren Durchmessern; die MetavCUT Standard Line profitiert somit von besserer Standzeit bei Standardbohrungen. Welchen Spitzenwinkel hat der Bohrer und warum ist das wichtig? Der Spiralbohrer besitzt einen Spitzenwinkel von 118°, was ein leichteres Eindringen in weichere Materialien und ein verbessertes Ansetzen auf gewölbten Oberflächen ermöglicht.
High-performance drill bits for demanding production
Drill bits designed for industrial manufacturing where precision, repeatability and tool life are decisive. Based on a spectrum from HSS and kobalt-alloyed hss-e for universal use to solid carbide drills for high-speed, high-precision serial production, this range covers applications from general engineering to automotive supplier work.
Why these drill bits are essential in the workshop and on the machining centre
Function and behaviour:
- primary use: creating accurate cylindrical holes
- typical machines: CNC machining centres, lathes and drill presses
- key design aspects: optimised chisel edge, defined point angles, flute geometry for reliable chip evacuation
Technical advantages and process benefits:
- reduced feed forces through optimised point geometry
- improved heat control with advanced coatings and, where specified, internal coolant supply
- extended tool life using solid carbide variants and multilayer coatings such as TiN / TiAlN
- process security on challenging materials thanks to tailored materials and geometries
Concrete benefits that boost productivity and quality
- predictable tool life and fewer tool changes, lowering machine downtime
- stable hole quality and consistent tolerances across long runs
- efficient chip control and thermal management for safe deep-hole and hardened-material drilling
- suitability across a wide material range, reducing the need for multiple specialised tools
Metav as a reliable partner for high-precision tooling
Metav combines decades of sector expertise with a broad, dependable offering from its Emmerich facility. With over 48,000 customers and more than 250,000 products, Metav positions its range of drill bits, twist drills and indexable drills as a practical, quality-first choice for procurement managers and production engineers seeking dependable supply and technical competence.
Technical data (at a glance)
- material: HSS, kobalt-alloyed hss-e, solid carbide
- coatings: TiN, TiAlN, advanced nanocoatings
- coolant option: internal coolant feed where specified
- typical applications: mild steel, high-alloy stainless steel, cast iron, non-ferrous metals, technical plastics, hardened materials (use solid carbide variants)
- tool types available: twist drills, solid carbide drills, indexable drills, centre and pilot drills, step drills
FAQ
What is the difference between hss and solid carbide drill bits?
HSS drill bits offer toughness and resistance to breakage for general machining, while solid carbide drills provide higher wear resistance and are the preferred choice for high-speed, high-volume machining and hardened materials.
Which coatings improve tool life for industrial drilling?
Coatings such as TiN and TiAlN increase surface hardness and thermal stability; when combined with the correct drill geometry and, if available, internal coolant, they significantly extend the service life of drill bits.
Can these drill bits be used on CNC machining centres for deep holes?
Yes. Drill bits designed with optimised flute geometry and internal coolant supply are suited to deep-hole machining on CNC machining centres, ensuring controlled chip evacuation and heat management.
How should I choose between twist drills, solid carbide drills and indexable drills?
Select twist drills for general-purpose drilling, solid carbide drills for high-speed and hardened-material applications, and indexable drills for large-diameter holes where insert changes offer economic advantages.
Why choose Metav for drill bits and drilling solutions?
Metav offers a comprehensive selection of drill bits, twist drills and indexable drills combined with sector expertise, centralised supply from Emmerich and proven reliability across thousands of industrial customers.
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com