How do I use a micrometer?

Precision blind‑hole inspection is facilitated by the combination of a self‑centring three‑point head, carbide measuring faces and an accuracy of ±0.005 mm; order the MS908.663 via Metav Werkzeuge or consult our advisors for specification support. MS908.663 — three‑point internal micrometer with self‑centring head and ±0.005 mm accuracy (Metav IndustryLine) A self‑centring three‑point internal micrometer MS908.663 designed for fast, repeatable measurement of blind holes in workshop and production environments. Self‑centring three‑point measuring head Accuracy ±0.005 mm for repeatable results Carbide measuring faces for long service life Delivered in a protective transport case Precise blind‑hole measurement with minimal operator error The three‑point measuring concept produces a natural centre‑finding action that stabilises the instrument inside a blind hole, reducing eccentricity and operator influence. With an analogue reading of 0.005 mm and an accuracy of ±0.005 mm, this gauge is suited to quality‑critical internal diameter checks where small deviations matter. The vernier‑style scale enables direct mechanical reading without reliance on batteries or electronics, supporting uninterrupted inspections on the shop floor. This combination of mechanical reliability and fine resolution promotes consistent pass/fail decisions during incoming inspection and first‑off checks. Built for demanding workshop use and long‑term repeatability Constructed with carbide measuring faces, the instrument resists wear in daily use and preserves measuring integrity over longer service intervals. The instrument’s physical length of 145 mm and measuring span of 100–125 mm places it in the standard measuring range for general machine‑shop applications, offering a practical balance between reach and rigidity. The robust design and hardened contact surfaces make the micrometer tolerant of routine handling; the supplied protective transport case reduces the risk of damage during storage and transit, keeping calibration stability intact. Practical advantages for process control and inspection routines Using a self‑centring, three‑point internal gauge streamlines internal diameter checks in blind holes, bores and recesses, enabling faster set‑ups at the bench or on the machine. The instrument’s repeatable seating and fine resolution help to reduce scrap and rework by catching dimensional drift earlier in the process. As an analogue instrument it integrates easily into established measurement routines and inspection sheets, while its mechanical simplicity minimises downtime compared with devices that rely on electronics. Typical applications and handling guidance The micrometer is intended for blind‑hole and internal diameter measurements in general engineering, toolroom checks and production quality control. For best results, ensure clean contact surfaces and a stable seating in the bore before taking a reading; the three‑point head will centre itself, but careful alignment reduces measurement scatter. Periodic verification against a gauge block or master ring is recommended to confirm ongoing accuracy and to schedule recalibration when necessary. The instrument’s durability and simple operation make it a practical choice for repetitive internal measurements on ferrous and non‑ferrous components. For reliable blind‑hole inspection with Metav IndustryLine precision, contact Metav Werkzeuge for purchase and expert advice by email at info@metav-werkzeuge.com or by telephone on +49 2822 7131930 Technical data Article number: MS908.663 Name: Three‑point internal micrometer Brand: Metav IndustryLine Type: Analogue internal measuring instrument Numbers / Core technical data Measuring range: 100–125 mm Measuring length: 145 mm Reading / Resolution: 0.005 mm Accuracy: ±0.005 mm Special features / Design Self‑centring three‑point measuring head Carbide measuring faces Delivered in a protective transport case Suitable for blind‑hole (blind bore) measurement FAQ How does the three‑point head help with blind‑hole measurement? The three‑point geometry of the MS908.663 automatically centres inside a blind hole, reducing eccentricity and improving repeatability of internal diameter readings. What level of accuracy and resolution can be expected? The instrument provides a resolution of 0.005 mm with an accuracy of ±0.005 mm, making it suitable for tight tolerance internal checks in production and workshop environments. Is the gauge suitable for frequent workshop use? Yes; the carbide measuring faces and robust mechanical construction are designed for daily inspection tasks and extended service life. Can this micrometer measure other internal features besides blind holes? While optimised for blind holes, the instrument can be used for internal diameter checks, recesses and similar internal features where the three‑point contact can seat reliably. What is included with the instrument on delivery? The MS908.663 is supplied complete with a protective transport case to protect the gauge during storage and transport. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Take advantage of the combination of compact design, repeatable self‑centring measurement and wear‑resistant carbide faces to maintain consistent bore quality in small components. Order the instrument directly via Metav Werkzeuge or consult our specialists for application advice. Three‑point internal micrometer MS908.653 — self‑centring three‑point head, carbide measuring faces (Metav IndustryLine) A Three‑point internal micrometer MS908.653 engineered for precise measurement of blind bores in workshop and quality‑control environments. Self‑centring three‑point measuring head Carbide measuring faces for wear resistance Precise range 12–16 mm with 0.004 mm accuracy Compact 80 mm body length for confined spaces Accurate measurements in confined bores The three‑point geometry provides a self‑centring effect that stabilises the measuring axis in blind holes, reducing eccentricity and improving repeatability. With a declared accuracy of 0.004 mm and a vernier reading increment of 0.005 mm, this analogue instrument delivers the fine mechanical resolution expected in micro‑component inspection. The design minimises operator variation by ensuring the measuring anvils expand symmetrically, which translates into faster decision‑making during incoming inspection or in‑process checks. Small format, specialist capability Classified in the Micro category (measuring range 12–16 mm), the tool combines a short 80 mm body length with a compact head that is easy to manoeuvre inside tight bores. The carbide measuring faces resist wear during repetitive use, extending the interval between maintenance cycles and preserving measurement integrity. An adjustment ring (size 16) allows repeatable pre‑settings for batch measurements, so set‑ups for small series or precision assemblies remain consistent without excessive rework. Built for blind‑hole tasks and straightforward handling Designed specifically for blind‑hole measurement, the three‑point micrometer eliminates the need for improvised measuring aids. Its analogue, non‑electronic construction favours robustness in workshop conditions and simplifies routine maintenance compared with electronic gauges. The combination of mechanical simplicity and the self‑centring head reduces measurement time and supports reliable dimensional control of bores used in bearings, housings and valve seats. Workshop integration and supplier confidence Metav IndustryLine supplies a practical measuring solution that fits established inspection routines and supports traceable quality processes. The instrument’s proven geometry and durable contact faces make it suitable for precision toolrooms and production lines where compact accuracy is required. For specification matching, calibration options and integration into existing quality workflows, Metav Werkzeuge acts as a single, reliable partner with rapid technical guidance and supply across Europe. Contact Metav Werkzeuge today for tailored technical advice and reliable supply of the MS908.653 three‑point internal micrometer via Metav Werkzeuge GmbH in Emmerich Technical data Article number: MS908.653 Brand: Metav IndustryLine Category: Messschrauben Facts Measuring range: 12.0–16.0 mm Measuring range (min): 12 mm Measuring range (max): 16 mm Body length: 80 mm Accuracy: 0.004 mm Reading increment: 0.005 mm Adjustment ring: 16 Special features Self‑centring three‑point head Carbide measuring faces Designed for blind‑hole measurement Analog/vernier design Compact micro‑class instrument FAQ What types of bores is this instrument intended for? This three‑point internal micrometer MS908.653 is designed for precise measurement of blind bores and internal diameters within its 12–16 mm range. How precise is the measurement and what resolution is readable? The instrument offers an accuracy of 0.004 mm with a vernier reading increment of 0.005 mm, providing fine mechanical resolution suitable for micro‑component inspection. Are the measuring faces durable for repetitive workshop use? Yes, the micrometer is fitted with carbide measuring faces to increase wear resistance during repetitive measurements and to maintain dimensional integrity. Is the micrometer suitable for small‑batch production set‑ups? Its compact 80 mm body and adjustment ring (size 16) enable repeatable pre‑settings, making the MS908.653 well suited to small series and frequent set‑ups. Can calibration or certification be arranged for this instrument? Calibration options and certificates can be arranged through Metav Werkzeuge; contact the supplier for available services and lead times. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Take advantage of the combination of compact, workshop‑grade precision and robust design for repeatable blind‑hole measurement; the self‑centring three‑point contact and hardened measuring faces deliver reliable results across production and maintenance tasks. Order the instrument directly via Metav Werkzeuge or consult our advisors for application guidance. Three‑point internal micrometer MS908.657 (Metav IndustryLine) — Self‑centring, 30–40 mm The Three‑point internal micrometer MS908.657 is a mechanically driven measuring instrument intended for precise internal diameter checks, especially blind‑hole applications in fine mechanical and light industrial environments. Self‑centring three‑point contact system Measurement range 30–40 mm Hardened measuring faces for durability Precision designed for blind‑hole measurement The three‑point geometry provides self‑centring contact inside blind holes, ensuring that the contact points align automatically with the bore axis and thereby reduce eccentricity errors. With an accuracy of ±0.004 mm and a mechanical reading of 0.005 mm, this analogue measuring instrument translates fine thread motion into dependable metrology results without electronic dependence. The three‑point contact method also helps to average minor surface irregularities, which can reduce rework and speed up routine inspection tasks, making it suitable for both small series production and maintenance checks. Compact format for fine mechanical work Classified in the Mikro range (measurement span up to 100 mm), the instrument’s 30–40 mm span and overall length of 97 mm offer a favourable balance between reach and stiffness. This makes the device well suited to precision tasks where space is limited, such as watch and instrument repair, small housings and insert fittings. The hardened measuring faces increase wear resistance and preserve measurement consistency over long service intervals, so that calibration intervals remain predictable and downtime is minimised. Workshop‑ready robustness and simple handling The analogue design emphasises mechanical reliability: a clear adjustment ring (setting ring 40) allows quick pre‑setting and repeatable contact positioning, while the compact construction withstands everyday workshop handling. Delivered in a protective case for transport, the micrometer is prepared for secure storage and movement between benches or sites. The instrument’s straightforward operation and sturdy build lower the barrier to consistent metrology in production, inspection and maintenance workflows while keeping measurement practice transparent and traceable. Contact Metav Werkzeuge today for tailored application advice on the Metav IndustryLine Three‑point internal micrometer MS908.657 and ensure the right fit for blind‑hole inspection in your workshop Technical data Article number: MS908.657 Manufacturer: Metav IndustryLine Product type: Three‑point internal micrometer Suitable for: Blind‑hole measurement Core data Measurement range: 30–40 mm Length: 97 mm Accuracy: ±0.004 mm Reading (resolution): 0.005 mm Adjustment ring: 40 Mechanical type: Analogue Special features Self‑centring three‑point contact Hardened measuring faces Delivered in protective case for transport Suited to fine mechanical and light industrial use FAQ What makes the three‑point contact better for blind holes? The three‑point geometry centres itself in the bore and averages contact positions; the MS908.657 uses this principle to reduce eccentricity and provide stable internal diameter readings for blind‑hole applications. What accuracy and resolution can be expected from this instrument? The instrument offers an accuracy of ±0.004 mm with a mechanical reading of 0.005 mm, giving precise analogue measurement suitable for production checks and workshop inspection. Is the device suitable for watchmaking and small parts? Yes. With its compact dimensions and classification in the Mikro range, the micrometer is well adapted to fine mechanical work, small housings and components where a short, stiff measuring span is required. Are the measuring faces wear‑resistant? The micrometer is supplied with hardened measuring faces, which increases durability and helps maintain measurement consistency over extended use. Does the delivery include a protective case? The instrument is supplied in a protective case for transport and secure storage, making it straightforward to move between benches or sites. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Benefit from the combination of self‑centring three‑point contact, 0.005 mm accuracy and carbide measuring faces to secure reproducible blind‑hole measurements; order the MS908.658 directly via Metav Werkzeuge or consult our specialists for application advice. Three‑point internal micrometer MS908.658 — self‑centring, 40–50 mm range (Metav IndustryLine) The Three‑point internal micrometer MS908.658 is a self‑centring, analogue instrument intended for precision measurement of blind holes and internal bores in small to medium components, offering a compact solution for fine mechanical and toolmaking tasks. Self‑centring three‑point measurement High precision: 0.005 mm accuracy Carbide measuring faces for durability Measuring range 40–50 mm for blind holes Reliable accuracy for critical fits and assemblies The MS908.658 delivers a resolution of 0.005 mm with a matching accuracy of 0.005 mm, providing measurable repeatability for tolerance‑sensitive internal features. The finely graduated analogue scale suits production and workshop environments where a tactile, immediate reading is preferred over electronic systems. This level of precision reduces rework and inspection time by supplying a clear, verifiable measurement result that supports quality control routines and efficient process decisions. Compact, micro‑range design that reduces handling error Classified in the micro range (max. 10–100 mm), the instrument’s 40–50 mm span targets finely detailed components such as small housings, inserts and precision sleeves. The self‑centring mechanism with three‑point contact automatically aligns the measuring faces within a bore, lowering sensitivity to off‑axis entry and operator variance. The compact form factor and balanced length make single‑handed operation straightforward, improving throughput where frequent in‑process checks are required. Durable measuring faces for long‑term repeatability Equipped with carbide (hardmetal) measuring faces, the micrometer resists wear and maintains measurement integrity across extended use. Carbide tips provide a hard, stable contact surface that minimises surface damage to workpieces while preserving repeatable reference points. For workshops seeking a robust, low‑maintenance gauge, this construction ensures a consistent lifecycle performance and contributes to lower total cost of ownership over time. Practical handling, calibration and typical applications The instrument is analogue and supplied with a setting ring at 40 mm to simplify zeroing and quick verification before series checks. Its total length of 97 mm facilitates access to compact bores while keeping the device rigid during measurement. Typical applications include blind‑hole inspection in toolmaking, component verification in precision engineering and quick fit checks in assembly processes. For specification matching and integration into inspection routines, Metav’s product consultants can assist with selection and measuring technique recommendations. Choose the Metav IndustryLine MS908.658 for reproducible blind‑hole measurement and contact Metav Werkzeuge in Emmerich for tailored technical advice: info@metav-werkzeuge.com / +49 2822 7131930 Technical data Article number: MS908.658 Type: Three‑point internal micrometer Brand: Metav IndustryLine Measuring range: 40–50 mm Resolution / reading: 0.005 mm Accuracy: 0.005 mm Operation: Analogue Setting ring: 40 Length: 97 mm Facts Measuring range: 40–50 mm Resolution: 0.005 mm Accuracy: ±0.005 mm Length: 97 mm Special features Self‑centring mechanism Three‑point contact for blind‑hole measurement Carbide (hardmetal) measuring faces Suited for fine mechanical and toolmaking applications Analogue scale for immediate readings FAQ What bore sizes can be measured with this instrument? The MS908.658 covers internal dimensions in the 40–50 mm range and is optimised for blind‑hole measurement within that span. How precise is the measurement capability? The instrument offers a resolution of 0.005 mm with an accuracy rated at 0.005 mm, suitable for many tolerance‑sensitive internal checks. Are the measuring faces wear‑resistant? Yes, the MS908.658 is fitted with carbide (hardmetal) measuring faces, which provide superior wear resistance and long‑term repeatability. Is this gauge suitable for production‑line checks? Its compact, analogue design and self‑centring three‑point system make the micrometer well suited to repetitive in‑process inspections and quick verification tasks. Does the micrometer require electronic data output? This model is analogue and does not include electronic data output; it is designed for direct, fast readings on the shop floor. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Benefit from the self-centring design, carbide measuring faces and ±0.005 mm accuracy to secure reproducible internal measurements in compact assemblies; order the three-point internal micrometer directly via Metav Werkzeuge or consult our specialists for technical guidance. Three-point internal micrometer MS908.660 — self-centring, 62–75 mm range A compact, analogue three-point internal micrometer designed for precise internal diameter checks in confined bores and fine-mechanical work. Self-centring three-point mechanism Measuring range 62–75 mm High accuracy ±0.005 mm Carbide measuring faces, analogue Precision where access is restricted The three-point internal micrometer is engineered for accurate measurements in confined spaces. Its self-centring mechanism ensures the measuring anvils align centrally within a bore, reducing operator-induced eccentricity and improving repeatability. With a readout resolution of 0.005 mm and a verified accuracy of ±0.005 mm, the instrument provides a reliable basis for quality control tasks where small deviations matter. The compact profile and 114 mm body length make this instrument particularly suitable for short, deep bores and components that cannot be accessed with larger gauges, offering precision without the need for complex fixturing. Durable construction for consistent results Built with carbide measuring faces, the instrument resists wear and maintains a stable contact geometry over extended use, which preserves measurement integrity in production environments. The analogue mechanism is robust and free of electronics, making it uncomplicated to operate in workshop conditions where durability is paramount. The combination of hardened contact surfaces and mechanical simplicity translates into low maintenance and consistent performance during repetitive checking routines, supporting efficient inspection workflows on the shop floor. Practical handling and typical applications Designed for ease of use in inspection and assembly, the instrument delivers fast, reliable readings for internal diameters between 62 and 75 mm. Its three-point contact is particularly effective for detecting form deviations and average bore sizes without additional adapters. Typical applications include component verification in machining, maintenance checks on housings and bearings, and quality assurance in small-batch production. The analogue format permits immediate interpretation of results, while the instrument’s geometry supports measurements that would be difficult with external gauges or callipers. Contact Metav Werkzeuge today for tailored advice and to arrange supply of the Metav IndustryLine three-point internal micrometer MS908.660 via Metav Werkzeuge GmbH; technical consultants are available at info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: MS908.660 Brand: Metav IndustryLine Type: Analogue three-point internal micrometer Measuring range: 62–75 mm Readout: 0.005 mm Accuracy: ±0.005 mm Body length: 114 mm Self-centring mechanism Carbide measuring faces Suitable for blind-hole measurement Analogue (mechanical) operation FAQ How accurate is the three-point internal micrometer for routine inspection? The MS908.660 delivers an accuracy of ±0.005 mm, making it suitable for routine precision checks and quality control where sub-hundredth-millimetre repeatability is required. Can the instrument be used in blind or recess bores? Yes, the design is intended for confined and blind-hole measurements; the three-point contact provides reliable central alignment inside such bores. What maintenance is required to preserve measurement accuracy? Regular cleaning of contact surfaces and occasional verification on a calibrated reference ring are recommended to maintain the micrometer’s performance; the carbide measuring faces reduce wear and extend intervals between checks. Is the readout mechanical or electronic? This is an analogue instrument with a mechanical readout at 0.005 mm resolution, favouring robustness in workshop settings without relying on electronics. Which environments and applications suit this instrument best? The three-point internal micrometer is ideal for machine shops, maintenance workshops and inspection benches where compact, repeatable internal measurements are needed across small to medium-sized components. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Compact, self‑centring three‑point internal micrometre with a 6.0–8.0 mm measuring range and high mechanical resolution; the MS908.650 combines precise blind‑hole measurement with hardened measuring faces and a fine 0.001 mm reading—Order the three‑point internal micrometre directly via Metav Werkzeuge or ask our consultants if needed Three‑point internal micrometre MS908.650 — self‑centring, 6.0–8.0 mm range Three‑point internal micrometre MS908.650 delivers reliable blind‑hole measurement for precision workshops and production lines Self‑centring three‑point contact Measuring range 6.0–8.0 mm Resolution 0.001 mm reading Hardened measuring faces (HM) Precision where blind‑hole bores matter The self‑centring three‑point contact mechanism ensures coaxial alignment inside blind holes, reducing measurement variability compared with two‑point probes. With a measuring range of 6.0–8.0 mm and an analogue vernier controlled fine adjustment, this instrument is optimised for small‑diameter bores where repeatability is critical. The device’s geometry minimises radial play so that each measurement reflects the actual bore diameter rather than positioning error, which is particularly valuable in small‑component assembly and quality control workflows. Exceptional reading and repeatability for workshop standards Equipped with a mechanical reading division of 0.001 mm, the instrument offers a fine visual resolution while the stated accuracy of ±0.004 mm provides a clear performance expectation for routine inspections. The analogue vernier design gives tactile feedback during measurement, enabling experienced operators to control contact force intuitively. This combination of high resolution and guaranteed accuracy supports process control in machining and metrology tasks where small deviations can affect assembly fit or functional tolerances. Durable contact faces for industrial use The micrometre is fitted with hardened measuring faces (HM) to withstand repeated contact with workpiece surfaces and abrasive contaminants found in production environments. These robust faces preserve the geometry of the contact points over long service intervals, which reduces drift and the need for frequent re‑profiling. In practice, hardened faces extend usable life and maintain measurement integrity when inspecting ferrous and non‑ferrous components during serial production. Designed for blind‑hole measurement and simple handling Specifically configured for blind‑hole bores, the three‑point contact and compact body (length 54.5 mm) permit access to confined features that larger gauges cannot reach. The instrument includes an adjustment ring (setting ring 6) that allows controlled extension of the contact arms, making it suitable for varied hole depths within the stated range. Its compact, mechanically driven construction requires no batteries and integrates easily into inspection benches, making it a practical choice for laboratories and on‑shop measuring stations where robustness and low maintenance are priorities. Contact Metav Werkzeuge today to discuss how the MS908.650 can be integrated into existing inspection routines or to request tailored advice from our technical consultants Technical data Article number: MS908.650 Manufacturer: Metav IndustryLine Type: Three‑point internal micrometre Facts Measuring range: 6.0–8.0 mm Length: 54.5 mm Reading increment: 0.001 mm Accuracy: ±0.004 mm Adjustment ring: 6 Special features Self‑centring three‑point contact Hardened measuring faces (HM) Analogue vernier reading Suitable for blind‑hole bores Category: Messschrauben FAQ What measurement range does this instrument cover? The MS908.650 covers a measuring range of 6.0–8.0 mm, optimised for small blind‑hole bores. Is the device suitable for repetitive production checks? Yes, the MS908.650 is designed for workshop and production use with hardened measuring faces and a robust three‑point contact that supports repeatable inspections. What level of accuracy and resolution can be expected? The instrument provides a reading increment of 0.001 mm and a stated accuracy of ±0.004 mm, suitable for demanding quality control tasks. Can the micrometre measure deep blind holes? The compact length (54.5 mm) and the adjustment ring (6) make the MS908.650 appropriate for many blind‑hole depths within its 6.0–8.0 mm range. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Benefit from precise three-point contact, a self-centring mechanism and an accuracy of 0.005 mm for reliable blind‑hole measurement; order the MS908.661 directly via Metav Werkzeuge or ask our consultants for application advice. Three‑point internal micrometer MS908.661 — 75–88 mm range, self‑centring (Metav IndustryLine) The Three‑point internal micrometer MS908.661 offers a compact, mechanically robust solution for accurate measurement of blind bores between 75 and 88 mm, combining repeatable contact geometry with workshop‑grade durability. Self‑centring three‑point contact Measuring range 75–88 mm Accuracy 0.005 mm Precise three‑point geometry for repeatable blind‑hole results The instrument employs a three‑point contact arrangement that engages the bore at equidistant positions, producing consistent centring and minimising eccentricity in blind‑hole measurements. With a specified accuracy of 0.005 mm and a reading increment of 0.005 mm, the mechanical design prioritises repeatability and straightforward interpretation of results. This focus on measurable performance supports quicker decision‑making on the shop floor and reduces the likelihood of rework caused by inconsistent bore centring. Robust construction and easy handling for daily use Built for persistent use in production and inspection areas, the gauge features hardened measuring faces and an analogue measuring mechanism that requires no batteries. The compact body (length 114 mm) and an adjustable setting ring (87) provide tactile control during measurement operations. Hardened contact surfaces extend service life under typical workshop conditions, while the analogue format keeps the instrument immediately usable without electronic maintenance. The combined effect is low‑maintenance operation with dependable mechanical accuracy. Practical suitability and workflow benefits Designed specifically for blind‑hole applications, the tool is suited to toolrooms, maintenance shops and quality control benches where internal diameters must be checked quickly and reliably. The self‑centring action reduces setup time and helps standardise measurement procedures across operators, improving throughput and traceability. As a purely mechanical gauge it integrates easily with established inspection routines and supports rapid pass/fail decisions without additional calibration steps beyond routine verification. Quality assurance and provenance that support procurement Supplied under the Metav IndustryLine umbrella, the instrument represents a balance of functional precision and workshop pragmatism. Choice of a mechanically driven, three‑point internal gauge is a rational investment when repeatability and simple operation are priorities. Metav’s approach to product selection and distribution provides transparency and supply reliability for industrial buyers who prioritise consistent measurement outcomes. For technical availability and procurement of the MS908.661 three‑point internal micrometer, contact Metav Werkzeuge for product guidance and stock information at info@metav-werkzeuge.com or by phone on +49 2822 7131930 Technical data Article number: MS908.661 Name: Three‑point internal micrometer Manufacturer: Metav IndustryLine Core specifications Measuring range: 75–88 mm Accuracy: 0.005 mm Reading increment: 0.005 mm Length: 114 mm Setting ring: 87 Special features Self‑centring three‑point contact Hardened measuring faces Analogue measuring mechanism Suitable for blind‑hole bores Category: Micrometers FAQ What measuring range does this instrument cover? The MS908.661 covers a measuring range of 75–88 mm and is therefore suited to medium‑sized internal diameters such as blind bores in assemblies. How precise is the measurement? Precision is stated as 0.005 mm with a reading increment of 0.005 mm, which ensures repeatable results for standard workshop inspection tasks. Why is three‑point contact advantageous for blind holes? Three‑point contact centres the gauge automatically within the bore, reducing eccentricity and improving repeatability compared with single‑point internal probes. Where is this instrument typically used? This analogue internal micrometer is used in toolrooms, maintenance workshops and quality control where robust, battery‑free measurement of blind bores is required. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Combining self-centring operation with a guaranteed 0.005 mm accuracy across an 87–100 mm measuring band, this instrument delivers repeatable results for blind-hole inspection and internal-diameter checks. Order via Metav Werkzeuge or request expert advice from our consultants for application-specific guidance. Three-Point Internal Micrometer MS908.662 — Self-centring, 87–100 mm, 0.005 mm accuracy (Metav IndustryLine) A compact, three-point internal micrometer MS908.662 engineered for precise measurement of blind bores and internal diameters in the 87–100 mm range. Self-centring measuring head 87–100 mm measurement range 0.005 mm graduation and accuracy Carbide measuring faces for durability Precision for blind-hole measurements that must be repeatable The three-point measuring principle combines three symmetrically arranged anvils to centre automatically within the bore, reducing alignment errors and improving repeatability. With a declared accuracy of 0.005 mm and a matching reading resolution of 0.005 mm, the instrument is configured for reliable internal measurements where tight tolerances apply. The mechanical three-point arrangement compensates for minor irregularities in bore geometry and, compared with single-anvil probes, significantly reduces positional uncertainty; this is particularly important when inspecting blind bores where full insertion of contact probes is not possible. Durable, workshop-ready design for routine inspection Constructed with carbide measuring faces, the unit withstands abrasive and repetitive contact without rapid wear, thus maintaining measurement integrity over time. The analogue vernier operation provides a dependable mechanical reading method that does not rely on batteries, ensuring continuous availability on the shop floor. The compact overall length (114 mm) and a preset setting ring at 87 mm allow straightforward setup for the nominal range and make the tool suitable for tight-access tasks. These attributes combine to reduce downtime and simplify daily inspection routines in toolrooms and maintenance departments. Micro-class capability and typical use cases With a maximum measuring range of 100 mm, this instrument falls within the micro classification for compact internal gauges, a category valued for high precision in confined spaces. Typical applications include fine mechanical assembly, toolmaking, quality control of small to medium-sized components, and inspection of blind-hole bores in housings and castings. The self-centring function and carbide contacts make it an effective choice for repeated checks during production runs and for settings where consistent, operator-independent measurement behaviour is required. For tailored application advice or to secure this self-centring internal micrometer from Metav Werkzeuge in Emmerich — contact info@metav-werkzeuge.com or call +49 2822 7131930 for consultancy and delivery options Technical Data Article number: MS908.662 Product: Three-point internal micrometer Brand: Metav IndustryLine Facts Measuring range: 87–100 mm Reading / Resolution: 0.005 mm Accuracy: 0.005 mm Overall length: 114 mm Setting ring: 87 mm Special features Self-centring three-point head Carbide measuring faces Analogue vernier operation Suitable for blind-hole bores FAQ Is this instrument suitable for measuring blind bores? Yes. The MS908.662 three-point internal micrometer from Metav IndustryLine is specifically designed for accurate measurement of blind-hole bores within the 87–100 mm band. What accuracy and resolution are provided? The tool offers a declared accuracy of 0.005 mm with a reading resolution of 0.005 mm, making it suitable for precise workshop inspection tasks. What are the measuring faces made from? The measuring faces are carbide-tipped to provide wear resistance and long-term dimensional stability under repeated use. Does the instrument require batteries or electronics? No. The device uses an analogue vernier principle and is entirely mechanical, eliminating the need for batteries and reducing maintenance points. For which workshop tasks is the micrometer best suited? Ideal for fine mechanical work, toolroom checks and production inspection of internal diameters and blind holes where compact, high-precision measuring tools are required. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com