wie benutzt man einen mikrometer?

Precision blind‑hole inspection is facilitated by the combination of a self‑centring three‑point head, carbide measuring faces and an accuracy of ±0.005 mm; order the MS908.663 via Metav Werkzeuge or consult our advisors for specification support. MS908.663 — three‑point internal micrometer with self‑centring head and ±0.005 mm accuracy (Metav IndustryLine) A self‑centring three‑point internal micrometer MS908.663 designed for fast, repeatable measurement of blind holes in workshop and production environments. Self‑centring three‑point measuring head Accuracy ±0.005 mm for repeatable results Carbide measuring faces for long service life Delivered in a protective transport case Precise blind‑hole measurement with minimal operator error The three‑point measuring concept produces a natural centre‑finding action that stabilises the instrument inside a blind hole, reducing eccentricity and operator influence. With an analogue reading of 0.005 mm and an accuracy of ±0.005 mm, this gauge is suited to quality‑critical internal diameter checks where small deviations matter. The vernier‑style scale enables direct mechanical reading without reliance on batteries or electronics, supporting uninterrupted inspections on the shop floor. This combination of mechanical reliability and fine resolution promotes consistent pass/fail decisions during incoming inspection and first‑off checks. Built for demanding workshop use and long‑term repeatability Constructed with carbide measuring faces, the instrument resists wear in daily use and preserves measuring integrity over longer service intervals. The instrument’s physical length of 145 mm and measuring span of 100–125 mm places it in the standard measuring range for general machine‑shop applications, offering a practical balance between reach and rigidity. The robust design and hardened contact surfaces make the micrometer tolerant of routine handling; the supplied protective transport case reduces the risk of damage during storage and transit, keeping calibration stability intact. Practical advantages for process control and inspection routines Using a self‑centring, three‑point internal gauge streamlines internal diameter checks in blind holes, bores and recesses, enabling faster set‑ups at the bench or on the machine. The instrument’s repeatable seating and fine resolution help to reduce scrap and rework by catching dimensional drift earlier in the process. As an analogue instrument it integrates easily into established measurement routines and inspection sheets, while its mechanical simplicity minimises downtime compared with devices that rely on electronics. Typical applications and handling guidance The micrometer is intended for blind‑hole and internal diameter measurements in general engineering, toolroom checks and production quality control. For best results, ensure clean contact surfaces and a stable seating in the bore before taking a reading; the three‑point head will centre itself, but careful alignment reduces measurement scatter. Periodic verification against a gauge block or master ring is recommended to confirm ongoing accuracy and to schedule recalibration when necessary. The instrument’s durability and simple operation make it a practical choice for repetitive internal measurements on ferrous and non‑ferrous components. For reliable blind‑hole inspection with Metav IndustryLine precision, contact Metav Werkzeuge for purchase and expert advice by email at info@metav-werkzeuge.com or by telephone on +49 2822 7131930 Technical data Article number: MS908.663 Name: Three‑point internal micrometer Brand: Metav IndustryLine Type: Analogue internal measuring instrument Numbers / Core technical data Measuring range: 100–125 mm Measuring length: 145 mm Reading / Resolution: 0.005 mm Accuracy: ±0.005 mm Special features / Design Self‑centring three‑point measuring head Carbide measuring faces Delivered in a protective transport case Suitable for blind‑hole (blind bore) measurement FAQ How does the three‑point head help with blind‑hole measurement? The three‑point geometry of the MS908.663 automatically centres inside a blind hole, reducing eccentricity and improving repeatability of internal diameter readings. What level of accuracy and resolution can be expected? The instrument provides a resolution of 0.005 mm with an accuracy of ±0.005 mm, making it suitable for tight tolerance internal checks in production and workshop environments. Is the gauge suitable for frequent workshop use? Yes; the carbide measuring faces and robust mechanical construction are designed for daily inspection tasks and extended service life. Can this micrometer measure other internal features besides blind holes? While optimised for blind holes, the instrument can be used for internal diameter checks, recesses and similar internal features where the three‑point contact can seat reliably. What is included with the instrument on delivery? The MS908.663 is supplied complete with a protective transport case to protect the gauge during storage and transport. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

The combination of precise self‑centring contact, a compact 10–12 mm measuring range and robust carbide faces ensures fast, repeatable blind‑hole measurements with minimal setup. Order the instrument directly via Metav Werkzeuge or consult the team for application advice. Metav IndustryLine Three‑Point Internal Micrometre MS908.652 — self‑centring, 10–12 mm range The Three‑Point Internal Micrometre MS908.652 is a compact analogue micrometre designed for precise diameter measurement inside blind holes and small bores in the 10–12 mm range. Self‑centring three‑point contact Measuring range 10–12 mm Accuracy 0.004 mm Carbide measuring faces Reliable centring for blind‑hole measurement A three‑point contact ensures rapid and reproducible alignment in blind holes, reducing repositioning time and measurement scatter. The micrometre’s self‑centring mechanism automatically locates the bore centre, so the operator obtains a consistent contact geometry on each measurement. With a measuring span of 10–12 mm the instrument is tailored to micro components and small bores where repeatability and short setup times are essential, improving throughput in small‑part inspection tasks. Durable contact surfaces for longer service life The measuring faces are manufactured as carbide contacts to resist wear and preserve accuracy during frequent use. The unit’s analogue design gives a tactile feel and straightforward reading, paired with a fine adjustment capability to approach tight fits carefully. The compact body (length approx. 54.5 mm) is suited to constrained access, while a setting ring (size 10) is included for verification and quick zeroing, supporting stable traceability in routine quality checks. Practical workflow advantages and workshop integration This three‑point micrometre combines simple operation with technical reliability: measurements are quick, calibration checks are straightforward and the tool integrates easily into existing inspection benches. Classified in the Micro range (max. 10–100 mm), it fulfils typical needs of precision engineering, watchmaking and small‑component production where stiffness, reach and single‑hand operation must be balanced. Metav’s distribution ensures European stock and reliable delivery from Emmerich. Request application guidance or order details from Metav Werkzeuge for the Metav IndustryLine three‑point internal micrometre MS908.652 — contact info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: MS908.652 Brand: Metav IndustryLine Category: Micrometres Type: Three‑point internal micrometre Measuring range: 10.0–12.0 mm Minimum range: 10 mm Maximum range: 12 mm Accuracy: 0.004 mm Length: 54.5 mm Setting ring: 10 Self‑centring three‑point contact Carbide (hard metal) measuring faces Analogue operation (nonius style) Suitable for blind‑hole bores FAQ How does the three‑point contact improve measurement in blind holes? The three‑point geometry of the MS908.652 centres automatically in a bore, giving a stable contact triangle that reduces wobble and improves repeatability compared with single‑point probes. What measurement accuracy can be expected from this instrument? The instrument is specified with an accuracy of 0.004 mm; in routine use this delivers repeatable diameter readings for small‑bore inspection tasks. Is the micrometre suitable for workshop use or only for laboratory conditions? Designed for practical workshop use, the robust carbide faces and analogue adjustment make the MS908.652 resilient to frequent handling while keeping measurement quality high. How is the instrument returned to zero or checked on site? A setting ring (size 10) is provided for quick verification and zeroing of the micrometre before inspection runs. Which components and applications benefit most from this micrometre? Small bores, precision fittings, watch‑ and micro‑mechanical parts and any blind‑hole diameters in the 10–12 mm range benefit from the compact form, self‑centring contact and carbide faces of the MS908.652. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Take advantage of the combination of high accuracy, wireless + USB data transfer and full ISO 17025 calibration with certificate for reliable measurements in precision workshops; order the three-point internal micrometre directly via Metav Werkzeuge or ask our consultants for tailored advice. Three‑Point Internal Micrometre – Digital internal measuring tool with wireless + USB and 1.5" colour touchscreen (Microtech Metrology) The Three‑Point Internal Micrometre is a compact digital instrument engineered for precise internal diameter measurement in small bores and precision components within the micro measurement category. *Digital display: 1.5" colour touchscreen *Wireless and USB data output *ISO 17025 calibrated with certificate *Measuring range 12–16 mm, 0.004 mm accuracy Accurate measurements for micro components Classified in the Micro category (suitable for very compact tasks), this instrument covers a measuring range of 12.0–16.0 mm, offering a practical reach for miniature assemblies and precision parts. The instrument combines a fine resolution of 0.0001 mm with a guaranteed accuracy of ±0.004 mm, which reduces measurement uncertainty and supports reproducible inspection results. Such precision is particularly valuable when inspecting small bores in sub‑assemblies where even slight deviations can affect fit and function. Traceable data capture and delivered calibration Designed for modern production environments, the micrometre provides wireless and USB connectivity for straightforward data transfer into inspection logs and SPC systems. The 1.5" colour touchscreen simplifies reading and setting adjustments on the shop floor, while the supplied setting ring ensures fast zeroing and repeatable reference points. The tool is supplied fully calibrated to ISO 17025 and includes a calibration certificate, enabling formal traceability and immediate use in processes that require accredited measurement results. Ergonomic handling that speeds up inspections The three‑point contact design centres measurement force, improving contact consistency inside bores and reducing operator‑induced variation. The compact format supports single‑hand operation in confined spaces and the intuitive touchscreen speeds routine checks, lowering cycle times and decreasing the likelihood of rework. The included setting ring and clear digital readout combine to make daily inspection routines both ergonomic and efficient. Integration into workshop quality routines With its digital outputs and compact form factor, the device integrates easily into existing inspection stations and handheld workflows. The substantial measuring depth of 230 mm provides versatility when accessing deeper bores or assemblies, while the three‑point mechanism ensures stable centring for reliable interior measurements. Together, these features support a consistent quality chain from initial inspection through to final acceptance. Contact Metav Werkzeuge in Emmerich for a suitability review or to request a quotation for this Microtech Metrology three‑point internal micrometre with ISO 17025 calibration; email info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: 133701610 GTIN: 4061905074219 Manufacturer: Microtech Metrology ECLASS: 21170335 Facts Measuring range: 12.0–16.0 mm Resolution: 0.0001 mm Accuracy: ±0.004 mm Measuring depth: 230 mm Special features Digital colour 1.5" touchscreen Data output: Wireless and USB Included setting ring ISO 17025 calibration with certificate Three‑point internal measuring spindle FAQ What bore sizes can be inspected with this instrument? The Three‑Point Internal Micrometre is designed for bores in the 12.0–16.0 mm range and is classified in the micro category for compact internal measurements. Is the micrometre delivered calibrated for traceability? Yes, the instrument is supplied fully calibrated to ISO 17025 and includes a calibration certificate for immediate traceable use. How are measurement results transferred to a PC or inspection system? Measurement data can be transmitted via the micrometre’s wireless interface or exported using the USB connection for integration into inspection logs. What level of precision can be expected during routine checks? Routine measurements with the Three‑Point Internal Micrometre offer a resolution of 0.0001 mm and an accuracy of ±0.004 mm, suitable for high‑precision shopfloor inspections. Does the tool include accessories for initial setup? The micrometre is supplied with an inclusive setting ring to establish a reproducible zero reference and support repeatable measurements. Manufacturer / Responsible: Microtech, Nizhneyurkovska str., 45a, 04080 Kyiv, Ukraine, tool@microtech.tools

Take advantage of self‑centring three‑point measuring, compact dimensions and a finely graduated reading for consistent blind‑bore checks; the combination of repeatable centring, carbide measuring faces and analogue robustness supports efficient workshop workflows. Order the Three‑point internal micrometer directly via Metav Werkzeuge or ask our consultants if needed. Three‑point internal micrometer MS908.654 — self‑centring, 16–20 mm range (Metav IndustryLine) The Three‑point internal micrometer MS908.654 is a precision instrument designed for reliable measurement of blind bores in the 16–20 mm band, combining a three‑point contact head with a compact frame for confined spaces Self‑centring three‑point head Measurement range 16–20 mm Carbide measuring faces (HM) Delivered in protective case Precise bore measurement where space is limited The three‑point contact design ensures automatic centring inside a blind bore so that the measuring points engage evenly; this reduces eccentricity and improves repeatability compared with single‑point probes. With a defined measurement range of 16–20 mm the instrument falls into the micro class of calipers, making it especially suitable for fine mechanical tasks and small assemblies where controlled measuring force and stable contact geometry are decisive for consistent results. The compact geometry helps to keep torsion low and supports reproducible checks in confined geometries. Workshop‑grade contact surfaces and durability Hard‑facing on the contact surfaces gives dependable wear resistance: the carbide measuring faces resist abrasion in routine shop use and extend service life under frequent contact with metal workpieces. The micrometer’s analogue construction avoids batteries and electronic vulnerabilities, favouring simple maintenance and immediate readiness. Supplied in a protective case, the instrument is shielded during transport and storage, supporting reliable deployment across different production stations. Readability and measurement certainty The instrument provides a fine reading step alongside a verified accuracy that supports confident decision making. With a display increment of 0.005 mm and an assessed accuracy of ±0.004 mm, the micrometer allows precise comparative measurements and go/no‑go assessments in production and quality control. The three‑point mechanism shortens setup time for successive measurements and reduces correctional effort, which increases throughput without compromising measurement integrity. Applications, classification and practical benefit Classified as a micro‑range internal micrometer, the tool is suited to watchmaking, valve seats, small hydraulic components and other blind‑hole checks where a short, rigid measuring system is required. The self‑centring function removes an additional alignment step, while the robust contact material supports mixed workshop environments. As a compact analogue instrument it combines mechanical simplicity with measurement quality, making it an efficient choice wherever repeatable internal diameters must be verified. For procurement or technical advice on Metav IndustryLine measuring instruments, contact Metav Werkzeuge in Emmerich for personalised guidance and secure delivery from our European warehouse Technical data SKU: MS908.654 Manufacturer: Metav IndustryLine Type: Three‑point internal micrometer Core specifications Measurement range: 16–20 mm Accuracy: ±0.004 mm Reading increment: 0.005 mm Overall length: 80 mm Analogue operation Features and materials Self‑centring three‑point head Carbide measuring faces Suitable for blind‑hole bores Delivered in protective case Compact micro‑range instrument FAQ What measurement range does this instrument cover? The Three‑point internal micrometer MS908.654 covers a range of 16–20 mm, designed for precise checks in small blind bores. How accurate is the micrometer for production checks? The instrument offers an assessed accuracy of ±0.004 mm with a reading increment of 0.005 mm, allowing reliable comparative measurements on small components. Are the contact faces suitable for regular shop use? Yes, the measuring faces are made of carbide, providing increased wear resistance and extended service life in routine workshop conditions with the Three‑point internal micrometer. Is this micrometer suitable for very tight or confined bores? Its compact frame and self‑centring three‑point head make the tool especially suitable for confined blind‑hole applications where stable contact and low torsion are required. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Take advantage of the self-centring three-point system and interchangeable measuring insert for reliable blind-hole measurements; combined with carbide measuring faces and an accuracy of ±0.007 mm, this instrument supports consistent quality control. Order the (three-point internal micrometer MS908.667) directly via (Metav Werkzeuge) or ask our consultants if needed. Three-point internal micrometer MS908.667 — self-centring, interchangeable insert The three-point internal micrometer for precise measurement of blind bores in workshop and inspection environments, designed as a mechanical instrument for repeatable internal diameter checks. Self-centring three-point system Interchangeable measuring insert Carbide measuring faces for wear resistance High precision ±0.007 mm Reliable blind-bore measurement with minimal operator influence The three-point system centres automatically within blind bores, reducing alignment errors and giving a reproducible contact geometry; this produces consistent results when inspecting bores. With a reading resolution of 0.005 mm (vernier) and a stated accuracy of ±0.007 mm, the instrument narrows measurement uncertainty to a level suitable for many workshop and production control tasks. The effect is a measurable reduction in rework and faster go/no-go decisions on turning and drilling operations. Durable contact surfaces and easy servicing save time Hard-wearing carbide measuring faces extend service intervals and maintain measurement integrity under repeated use. The measuring insert is exchangeable, which simplifies maintenance and allows quick replacement of worn contacts without discarding the whole instrument. The mechanical construction is straightforward and low-maintenance compared with electronic systems, making it suitable for environments where robustness and simple servicing are priorities. Size and handling tuned to everyday workshop needs Classified in the standard measuring range (measuring range 200–225 mm), this device offers a practical balance of reach and stiffness for typical machine‑shop components such as housings, sleeves and medium-sized bores. The instrument’s overall length of 145 mm supports good accessibility in confined bores while remaining easy to handle during repeated checks. As an analogue instrument with a vernier readout, it performs reliably where electronic readouts are unnecessary or undesired. Confidence for quality control and process stability Intended for routine inspection and in-process checks, the micrometer’s self-centring action and robust contact faces reduce operator-dependent variation and increase throughput in batch inspection. The interchangeable insert concept supports lifecycle planning: wear parts can be stocked and replaced quickly to maintain traceable measurement performance. The device is suitable for blind-hole measurement tasks and integrates well into manual quality-control workflows where mechanical verifiability is required. Contact Metav Werkzeuge today for ordering details and specification advice on the Metav IndustryLine three-point internal micrometer MS908.667 and its spare measuring inserts Technical Data Article number: MS908.667 Manufacturer: Metav IndustryLine Category: Micrometers (internal micrometer) Facts Measuring range: 200–225 mm Reading / Resolution: 0.005 mm Accuracy: ±0.007 mm Overall length: 145 mm Display: analogue (vernier) Features & Delivery Self-centring three-point system Carbide measuring faces Interchangeable measuring insert Designed for blind bores (blind-hole measurement) Mechanical, analogue instrument FAQ How does the three-point centring reduce measurement error? The self-centring three-point mechanism distributes contact forces evenly; the three-point internal micrometer MS908.667 centres itself in the bore to reduce eccentricity and improve repeatability. Can the measuring faces be replaced when worn? Yes — the instrument is fitted with an exchangeable measuring insert, so worn carbide faces can be renewed without replacing the entire micrometer. Is the reading digital or mechanical? The device uses a mechanical vernier readout with a reading resolution of 0.005 mm, offering a robust, electronics-free solution for workshop environments. For which bore types is this instrument intended? It is designed specifically for blind bores; the three-point configuration ensures reliable contact geometry in such applications. What is the measuring range and typical accuracy? The measuring range is 200–225 mm and the stated accuracy is ±0.007 mm, suitable for standard workshop inspection tasks. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Compact, self‑centring three‑point internal micrometre with a 6.0–8.0 mm measuring range and high mechanical resolution; the MS908.650 combines precise blind‑hole measurement with hardened measuring faces and a fine 0.001 mm reading—Order the three‑point internal micrometre directly via Metav Werkzeuge or ask our consultants if needed Three‑point internal micrometre MS908.650 — self‑centring, 6.0–8.0 mm range Three‑point internal micrometre MS908.650 delivers reliable blind‑hole measurement for precision workshops and production lines Self‑centring three‑point contact Measuring range 6.0–8.0 mm Resolution 0.001 mm reading Hardened measuring faces (HM) Precision where blind‑hole bores matter The self‑centring three‑point contact mechanism ensures coaxial alignment inside blind holes, reducing measurement variability compared with two‑point probes. With a measuring range of 6.0–8.0 mm and an analogue vernier controlled fine adjustment, this instrument is optimised for small‑diameter bores where repeatability is critical. The device’s geometry minimises radial play so that each measurement reflects the actual bore diameter rather than positioning error, which is particularly valuable in small‑component assembly and quality control workflows. Exceptional reading and repeatability for workshop standards Equipped with a mechanical reading division of 0.001 mm, the instrument offers a fine visual resolution while the stated accuracy of ±0.004 mm provides a clear performance expectation for routine inspections. The analogue vernier design gives tactile feedback during measurement, enabling experienced operators to control contact force intuitively. This combination of high resolution and guaranteed accuracy supports process control in machining and metrology tasks where small deviations can affect assembly fit or functional tolerances. Durable contact faces for industrial use The micrometre is fitted with hardened measuring faces (HM) to withstand repeated contact with workpiece surfaces and abrasive contaminants found in production environments. These robust faces preserve the geometry of the contact points over long service intervals, which reduces drift and the need for frequent re‑profiling. In practice, hardened faces extend usable life and maintain measurement integrity when inspecting ferrous and non‑ferrous components during serial production. Designed for blind‑hole measurement and simple handling Specifically configured for blind‑hole bores, the three‑point contact and compact body (length 54.5 mm) permit access to confined features that larger gauges cannot reach. The instrument includes an adjustment ring (setting ring 6) that allows controlled extension of the contact arms, making it suitable for varied hole depths within the stated range. Its compact, mechanically driven construction requires no batteries and integrates easily into inspection benches, making it a practical choice for laboratories and on‑shop measuring stations where robustness and low maintenance are priorities. Contact Metav Werkzeuge today to discuss how the MS908.650 can be integrated into existing inspection routines or to request tailored advice from our technical consultants Technical data Article number: MS908.650 Manufacturer: Metav IndustryLine Type: Three‑point internal micrometre Facts Measuring range: 6.0–8.0 mm Length: 54.5 mm Reading increment: 0.001 mm Accuracy: ±0.004 mm Adjustment ring: 6 Special features Self‑centring three‑point contact Hardened measuring faces (HM) Analogue vernier reading Suitable for blind‑hole bores Category: Messschrauben FAQ What measurement range does this instrument cover? The MS908.650 covers a measuring range of 6.0–8.0 mm, optimised for small blind‑hole bores. Is the device suitable for repetitive production checks? Yes, the MS908.650 is designed for workshop and production use with hardened measuring faces and a robust three‑point contact that supports repeatable inspections. What level of accuracy and resolution can be expected? The instrument provides a reading increment of 0.001 mm and a stated accuracy of ±0.004 mm, suitable for demanding quality control tasks. Can the micrometre measure deep blind holes? The compact length (54.5 mm) and the adjustment ring (6) make the MS908.650 appropriate for many blind‑hole depths within its 6.0–8.0 mm range. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Benefit from precise three-point contact, a self-centring mechanism and an accuracy of 0.005 mm for reliable blind‑hole measurement; order the MS908.661 directly via Metav Werkzeuge or ask our consultants for application advice. Three‑point internal micrometer MS908.661 — 75–88 mm range, self‑centring (Metav IndustryLine) The Three‑point internal micrometer MS908.661 offers a compact, mechanically robust solution for accurate measurement of blind bores between 75 and 88 mm, combining repeatable contact geometry with workshop‑grade durability. Self‑centring three‑point contact Measuring range 75–88 mm Accuracy 0.005 mm Precise three‑point geometry for repeatable blind‑hole results The instrument employs a three‑point contact arrangement that engages the bore at equidistant positions, producing consistent centring and minimising eccentricity in blind‑hole measurements. With a specified accuracy of 0.005 mm and a reading increment of 0.005 mm, the mechanical design prioritises repeatability and straightforward interpretation of results. This focus on measurable performance supports quicker decision‑making on the shop floor and reduces the likelihood of rework caused by inconsistent bore centring. Robust construction and easy handling for daily use Built for persistent use in production and inspection areas, the gauge features hardened measuring faces and an analogue measuring mechanism that requires no batteries. The compact body (length 114 mm) and an adjustable setting ring (87) provide tactile control during measurement operations. Hardened contact surfaces extend service life under typical workshop conditions, while the analogue format keeps the instrument immediately usable without electronic maintenance. The combined effect is low‑maintenance operation with dependable mechanical accuracy. Practical suitability and workflow benefits Designed specifically for blind‑hole applications, the tool is suited to toolrooms, maintenance shops and quality control benches where internal diameters must be checked quickly and reliably. The self‑centring action reduces setup time and helps standardise measurement procedures across operators, improving throughput and traceability. As a purely mechanical gauge it integrates easily with established inspection routines and supports rapid pass/fail decisions without additional calibration steps beyond routine verification. Quality assurance and provenance that support procurement Supplied under the Metav IndustryLine umbrella, the instrument represents a balance of functional precision and workshop pragmatism. Choice of a mechanically driven, three‑point internal gauge is a rational investment when repeatability and simple operation are priorities. Metav’s approach to product selection and distribution provides transparency and supply reliability for industrial buyers who prioritise consistent measurement outcomes. For technical availability and procurement of the MS908.661 three‑point internal micrometer, contact Metav Werkzeuge for product guidance and stock information at info@metav-werkzeuge.com or by phone on +49 2822 7131930 Technical data Article number: MS908.661 Name: Three‑point internal micrometer Manufacturer: Metav IndustryLine Core specifications Measuring range: 75–88 mm Accuracy: 0.005 mm Reading increment: 0.005 mm Length: 114 mm Setting ring: 87 Special features Self‑centring three‑point contact Hardened measuring faces Analogue measuring mechanism Suitable for blind‑hole bores Category: Micrometers FAQ What measuring range does this instrument cover? The MS908.661 covers a measuring range of 75–88 mm and is therefore suited to medium‑sized internal diameters such as blind bores in assemblies. How precise is the measurement? Precision is stated as 0.005 mm with a reading increment of 0.005 mm, which ensures repeatable results for standard workshop inspection tasks. Why is three‑point contact advantageous for blind holes? Three‑point contact centres the gauge automatically within the bore, reducing eccentricity and improving repeatability compared with single‑point internal probes. Where is this instrument typically used? This analogue internal micrometer is used in toolrooms, maintenance workshops and quality control where robust, battery‑free measurement of blind bores is required. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Combining self-centring operation with a guaranteed 0.005 mm accuracy across an 87–100 mm measuring band, this instrument delivers repeatable results for blind-hole inspection and internal-diameter checks. Order via Metav Werkzeuge or request expert advice from our consultants for application-specific guidance. Three-Point Internal Micrometer MS908.662 — Self-centring, 87–100 mm, 0.005 mm accuracy (Metav IndustryLine) A compact, three-point internal micrometer MS908.662 engineered for precise measurement of blind bores and internal diameters in the 87–100 mm range. Self-centring measuring head 87–100 mm measurement range 0.005 mm graduation and accuracy Carbide measuring faces for durability Precision for blind-hole measurements that must be repeatable The three-point measuring principle combines three symmetrically arranged anvils to centre automatically within the bore, reducing alignment errors and improving repeatability. With a declared accuracy of 0.005 mm and a matching reading resolution of 0.005 mm, the instrument is configured for reliable internal measurements where tight tolerances apply. The mechanical three-point arrangement compensates for minor irregularities in bore geometry and, compared with single-anvil probes, significantly reduces positional uncertainty; this is particularly important when inspecting blind bores where full insertion of contact probes is not possible. Durable, workshop-ready design for routine inspection Constructed with carbide measuring faces, the unit withstands abrasive and repetitive contact without rapid wear, thus maintaining measurement integrity over time. The analogue vernier operation provides a dependable mechanical reading method that does not rely on batteries, ensuring continuous availability on the shop floor. The compact overall length (114 mm) and a preset setting ring at 87 mm allow straightforward setup for the nominal range and make the tool suitable for tight-access tasks. These attributes combine to reduce downtime and simplify daily inspection routines in toolrooms and maintenance departments. Micro-class capability and typical use cases With a maximum measuring range of 100 mm, this instrument falls within the micro classification for compact internal gauges, a category valued for high precision in confined spaces. Typical applications include fine mechanical assembly, toolmaking, quality control of small to medium-sized components, and inspection of blind-hole bores in housings and castings. The self-centring function and carbide contacts make it an effective choice for repeated checks during production runs and for settings where consistent, operator-independent measurement behaviour is required. For tailored application advice or to secure this self-centring internal micrometer from Metav Werkzeuge in Emmerich — contact info@metav-werkzeuge.com or call +49 2822 7131930 for consultancy and delivery options Technical Data Article number: MS908.662 Product: Three-point internal micrometer Brand: Metav IndustryLine Facts Measuring range: 87–100 mm Reading / Resolution: 0.005 mm Accuracy: 0.005 mm Overall length: 114 mm Setting ring: 87 mm Special features Self-centring three-point head Carbide measuring faces Analogue vernier operation Suitable for blind-hole bores FAQ Is this instrument suitable for measuring blind bores? Yes. The MS908.662 three-point internal micrometer from Metav IndustryLine is specifically designed for accurate measurement of blind-hole bores within the 87–100 mm band. What accuracy and resolution are provided? The tool offers a declared accuracy of 0.005 mm with a reading resolution of 0.005 mm, making it suitable for precise workshop inspection tasks. What are the measuring faces made from? The measuring faces are carbide-tipped to provide wear resistance and long-term dimensional stability under repeated use. Does the instrument require batteries or electronics? No. The device uses an analogue vernier principle and is entirely mechanical, eliminating the need for batteries and reducing maintenance points. For which workshop tasks is the micrometer best suited? Ideal for fine mechanical work, toolroom checks and production inspection of internal diameters and blind holes where compact, high-precision measuring tools are required. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com