Precise HSS-G twist drill for millimetre-accurate, burr-free holes
The HSS-G twist drill DIN 338 type N is a short, ground, uncoated tool with a 135° split point designed to deliver self-centring, repeatable drilling in steel, iron, sheet materials and non-ferrous metals. Its ground profile from high-speed steel gives superior run-out accuracy, razor-sharp cutting edges and extremely smooth flutes that reduce friction and prevent chip adhesion when machining aluminium and plastics. The 135° cross-ground tip eliminates the need for centre-punching, lowering thrust forces and preventing wander on smooth surfaces, which ensures process-reliable and dimensionally accurate holes. As a universal and economical choice for professional workshop and industrial use, this drill offers consistent chip evacuation and clean, true holes with minimal burr formation.
4.9mm HSS-G Twist Drill DIN 338 ,short, bright finished, Type N - MetavCUT
Twist Drill — short HSS‑G 4.9 mm, 135° (Type N), bright finished The Twist Drill short HSS‑G 4.9 mm is a precision metal‑drilling bit for drilling machines and hand drills, designed for stable, accurate holes in hard materials. Short HSS‑G design for metal drilling 135° point angle for harder materials Fully ground shank for high concentricity Conforms to DIN 338 for short twist drills Profi Line finish for precise, clean boreholes High performance for demanding metal work The Twist Drill from MetavCUT is engineered as a short HSS‑G cutting tool that achieves up to 40% faster drilling with 50% less thrust force compared with conventional HSS drills, thanks to the ground geometry. The reduced cantilever length increases stability and reduces deflection, so the bit cuts cleaner and requires less rework. This makes the tool particularly suited for precision tasks in workshops and production environments where efficiency and repeatability matter. Reliable drilling in hard and alloyed materials With a 135° point angle and Type N normal spiral, this short twist drill is optimised for stainless steel, alloyed and unalloyed steels, cast steels, sintered iron and hard plastics. The DIN 338 classification confirms the design as a short cylindrical shank drill in HSS‑G quality, where grinding creates very sharp cutting edges and high runout accuracy. For users with limited metallurgical knowledge: a larger point angle reduces initial cutting forces and improves centring when penetrating tougher surfaces. Greater control and easier handling The fully ground shank and shortened overall length give the drill superior concentricity and less vibration in both drilling machines and compatible hand drills. Where rigidity is essential, the short design minimises chatter and improves hole quality. For workshop use, this means fewer tool changes and less scrap. Note that ground HSS drills are harder but can be more brittle than rolled alternatives, so recommend controlled feed, suitable cooling and stationary clamping for maximum tool life. Designed for professionals who demand precision Part of the Profi Line, the bright finished short twist drill combines a smooth surface with precise geometry to deliver clean chips and reliable hole tolerance. The 4.9 mm diameter and 86 mm overall length balance reach and rigidity for common metalworking tasks. For those seeking expert advice on suitability for specific alloys, hole tolerances or recommended feed rates, MetavCUT tools are supported by METAV Werkzeuge with comprehensive, competent consultation and after‑sales support. Strong recommendation: Choose the MetavCUT short Twist Drill for precise, efficient metal drilling and contact METAV Werkzeuge for tailored technical advice via info@metav-werkzeuge.com or by phone +49 2822 7131930, WhatsApp +49 170 2837271 Twist Drill Brand: MetavCUT SKU: 48049-FDA Diameter: 4.9 mm Point angle: 135° Type: Type N Execution: short Spiral length: 52 mm Overall length: 86 mm Shank execution: fully ground Finish/Colour: bright finished Material: HSS-G Norm: DIN 338 Application: Drills for metal For drilling machine: Drilling Machine / Hand drill Model series: Profi Line Manufacturer: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What is the MetavCUT Twist Drill used for The MetavCUT Twist Drill short HSS‑G is primarily used for drilling high‑strength materials and larger diameters in metalworking; its ground design keeps cutting edges very sharp and maintains precision under demanding loads. Which three drill types exist When classifying common drill categories, there are metal drills, wood drills and masonry/concrete drills; the MetavCUT Twist Drill belongs to the metal drill family and is optimised for steel and other hard materials. Why are twist drills sharpened Twist drills are sharpened to reduce the cross cutting edge at the tip, which lowers friction and required feed force while improving centring; sharpening the MetavCUT Twist Drill therefore reduces heat and makes guided entry into the workpiece easier. Can a metal twist drill be used in wood A metal drill such as the MetavCUT Twist Drill can be used in wood, but it will usually give less precise guidance and a rougher finish compared with a dedicated wood drill; however, metal drills are easier to resharpen and typically have less aggressive self‑feeding.
4mm HSS-G Twist Drill DIN 338 ,short, bright finished, Type N - MetavCUT
Kompakte Kombination aus Stabilität und Präzision: Der kurze, geschliffene HSS-G Spiralbohrer mit 135° Spitzenwinkel ermöglicht bis zu 40 % schnelleres Bohren bei gleichzeitig 50 % geringerer Anpresskraft und eignet sich besonders für legierte und unlegierte Stähle. Für stationäre Maschinen und handgeführte Bohrmaschinen geeignet. Bestellen Sie den MetavCUT Spiralbohrer direkt über Metav oder fragen Sie unsere Beratung bei Bedarf an. Spiralbohrer 4 mm HSS-G, kurze Ausführung, Profi Line Der Spiralbohrer 4 mm HSS-G in kurzer Ausführung bietet hohe Stabilität und präzise Bohrungen in Metall bei stationären und handgeführten Anwendungen. Kurze Ausführung für höhere Stabilität Geschliffene HSS-G-Geometrie für präzise Bohrungen 135° Spitzenwinkel für harte Werkstoffe Geeignet für Handbohrmaschine und stationäre Maschinen DIN 338 Klassifikation, Profi Line Höhere Standfestigkeit durch kurze Auskraglänge Die kurze Bauform reduziert die Auskraglänge und minimiert somit Verformung und Vibrationen beim Bohren. Dadurch entsteht eine spürbar höhere Stabilität, die insbesondere bei harten Werkstoffen wie legiertem Stahl oder Gusseisen saubere Bohrbilder und längere Werkzeugstandzeiten ermöglicht. Für Anwender heißt das: gleichmäßigere Bohrungsqualität und weniger Ausschuss bei Serien- oder Einzelteilen. Schnelleres und effizienteres Bohren dank geschliffener Geometrie Die geschliffene HSS-G-Geometrie sorgt für sehr scharfe Schneiden und hohe Rundlaufgenauigkeit. In der Praxis führt das zu bis zu 40 % schnellerem Bohren und reduziertem Kraftaufwand, wodurch die Belastung für Maschine und Bediener sinkt. Für weniger erfahrene Anwender ist dies ein Vorteil, weil das Bohren kontrollierter gelingt und das Risiko von Anlaufrissen am Bohranfang reduziert wird. Spezifische Eignung für Metall und Anwendungsbereiche Der Spiralbohrer wurde speziell für die Bearbeitung von Stahl, legiertem Stahl, Gusseisen, Temperguss, Nichteisenmetallen und harten Kunststoffen entwickelt. Als Typ N mit Normalspirale überzeugt er im Standard-Bereich (2–13 mm) und ist für alltägliche Werkstattaufgaben sowie präzise Montagearbeiten gut geeignet. Wer häufig in Metall bohrt, profitiert von der ausgewogenen Kombination aus Standzeit und Zerspanleistung. Praktische Hinweise zur Anwendung und Maschinenwahl Bei handgeführten Bohrmaschinen empfiehlt sich das Anpicken oder Zentrieren vor dem Bohren, um ein Wandern des Bohrers zu vermeiden. Stationäre Maschinen erlauben höhere Präzision und schonen das Werkzeug. Zur Kühlung und Späneabfuhr ist bei langen Serienläufen die Nutzung von Kühlschmierstoff oder geeigneter Späneabfuhr sinnvoll, damit die Lebensdauer des Werkzeugs erhalten bleibt. Vorteile der DIN-338-Norm und geschliffener Ausführung erklärt Die Einordnung nach DIN 338 garantiert standardisierte Abmessungen und Austauschbarkeit. Geschliffen bedeutet, dass die Spirallage präzise per CNC geschliffen wurde, was besonders scharfe Kanten und saubere Bohrungen liefert. Diese Ausführung ist besonders dann vorteilhaft, wenn hohe Maßhaltigkeit und Oberflächenqualität gefordert sind. Empfehlung: Für präzise Metallbearbeitung den MetavCUT Spiralbohrer mit geschliffener HSS-G-Geometrie wählen und Verfügbarkeit direkt bei Metav prüfen: info@metav-werkzeuge.com · Tel. +49 2822 7131930 · WhatsApp +49 170 2837271 Produktmerkmale Artikelnummer: 48040-FDA Marke: MetavCUT Serie: Profi Line Bezeichnung: Spiralbohrer Fakten Durchmesser: 4 mm Gesamtlänge: 75 mm Spirallänge: 43 mm Spitzenwinkel: 135° Verpackungseinheit: 10 Besonderheiten Material: HSS-G (Schnellarbeitsstahl, geschliffen) Schaftausführung: geschliffen (voll geschliffen für hohe Rundlaufgenauigkeit) Norm: DIN 338 (kurze Spiralbohrer mit Zylinderschaft) Ausführung: kurz (reduzierte Auskraglänge, höhere Stabilität) Typ: Typ N (Normalspirale, geeignet für Metallbearbeitung) Oberfläche: blank (bright finished) Für Bohrmaschine: Handbohrmaschine FAQ Ist der Spiralbohrer für Edelstahl geeignet? Der MetavCUT Spiralbohrer 4 mm HSS-G mit 135° Spitzenwinkel eignet sich für viele harte Werkstoffe; bei besonders zähem Edelstahl sind angepasste Schnittwerte und Kühlung empfehlenswert, um Standzeit zu maximieren. Kann der Bohrer in einer Handbohrmaschine verwendet werden? Ja, der kurze Spiralbohrer wurde für den Einsatz in Handbohrmaschinen und stationären Maschinen konzipiert; durch die kurze Ausführung erhöht sich die Stabilität beim handgeführten Bohren. Was bedeutet HSS-G geschliffen und welchen Vorteil bringt das? HSS-G steht für geschliffenen Schnellarbeitsstahl; diese Fertigungsart liefert sehr scharfe Schneiden und hohe Rundlaufgenauigkeit, was zu präziseren Bohrlöchern und häufig besseren Oberflächen führt. Wie beeinflusst der 135° Spitzenwinkel die Bohrung? Der größere Spitzenwinkel reduziert die Anbohrbelastung in harten Werkstoffen, verbessert die Zentrierung und verringert das Risiko von Ausrissen; daher ist er für legierte Stähle und Gussmaterialien empfehlenswert. Ist der Bohrer nach DIN 338 gefertigt und was heißt das praktisch? Ja, die Ausführung entspricht DIN 338; das garantiert standardisierte Abmessungen, Austauschbarkeit und eine klare Einordnung der kurzen Spiralbohrer mit Zylinderschaft.
5.1mm HSS-G Twist Drill DIN 338 ,short, bright finished, Type N - MetavCUT
Twist Drill — Short HSS‑G Twist Drill, Ø 5.1 mm, 135° Tip, Type N, Bright Finished, Short Version, DIN 338, MetavCUT The Twist Drill short Type N is a precision HSS‑G metalworking drill designed for stable, accurate holes in hard and alloyed steels, ideal for use with drilling machines and hand drills. Short design for increased rigidity HSS‑G ground for sharp cutting edges 135° tip for hard metals and stainless steel Suited for Drilling Machine and hand drills Conforms to DIN 338 for short twist drills Short design and material for higher drilling efficiency The Twist Drill from MetavCUT features a short overall length and a reduced exposed flute length, which significantly increases Stability during machining and reduces the tendency to deflect. Made from HSS‑G (ground high speed steel), the tool delivers very sharp cutting edges and excellent concentricity. The grinding process produces a clean geometry that allows more efficient chip removal and a longer useful life under correct operating conditions. For customers who need a reliable solution for demanding metal applications, this combination of short design and ground HSS offers clear performance advantages. Precise tip geometry for demanding materials A 135° Tip Angle makes this short Twist Drill particularly suitable for drilling hard materials such as stainless steel and tempered alloys. The flatter point reduces the tendency to wander on the surface and shortens plunge time when entering the workpiece. As a Type N (normal spiral) geometry, it represents the classic metalworking design and balances cutting action with chip evacuation. This geometry reduces feed forces compared with blunt angles and enables cleaner, more accurate holes when used with appropriate coolant and clamping. Typical applications and who benefits most This Twist Drill is intended primarily for metalworking: alloyed and unalloyed steels, cast steels, cast iron, sintered iron, non‑ferrous metals and hard plastics. Its robust short form is ideal for precision tasks on stationary and portable drilling machines where rigidity matters. Workshops, maintenance departments and precision fabricators who require repeatable hole quality in tougher materials will find this tool particularly advantageous. The ground HSS construction also allows easier regrinding and refurbishment when necessary, extending tool life under professional maintenance. Standards and manufacturing details that matter Manufactured to DIN 338, this short Twist Drill conforms to the classification and dimensional tolerances expected for short cylindrical shank HSS drills. The designation HSS‑G indicates a ground flute geometry, often referred to as HSS‑G or HSS‑Ground, which provides high surface finish and accurate runout. The drill is delivered with a fully ground shank, a bright finished appearance and a precise flute geometry that supports high concentricity in chucks and collets. For stationary machine use, the ground variant offers excellent repeatability—while noting that ground drills can be somewhat more brittle and benefit from proper cooling during heavy machining. Highly recommended: Choose MetavCUT’s precision short Twist Drill for demanding metalworking tasks — METAV Werkzeuge offers expert advice and technical support; contact METAV Werkzeuge for consultation at info@metav-werkzeuge.com, phone +49 2822 7131930 or WhatsApp +49 170 2837271 Twist Drill Brand: MetavCUT SKU: 48051-FDA Diameter: 5.1 mm Tip Angle: 135° Type: Type N Execution: short Finish: bright finished Material: HSS‑G Spiral Length: 52 mm Overall Length: 86 mm Shank Finish: fully ground Application: Drills for metal Model Series: Profi Line Standard: DIN 338 For Drilling Machine: Drilling Machine Manufacturer: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ For what is a Twist Drill used? The MetavCUT Twist Drill (Type N) is mainly used for machining high‑strength materials and larger drill diameters; its design is well suited to demanding metalworking tasks. The ground geometry is easy to resharpen and remains capable under higher loads, making it particularly useful when drilling steels and other tough materials. Which three drill types exist? Common drill families are metal drills, wood drills and masonry/concrete drills; the MetavCUT Twist Drill belongs to the metal drill category and is optimised for metalworking rather than softwood or masonry applications.
5.2mm HSS-G Twist Drill DIN 338 ,short, bright finished, Type N - MetavCUT
Twist Drill (Type N) — 5.2 mm, 135°, short, HSS‑G, Bright Finished — MetavCUT Profi Line The Twist Drill (Type N) is a short HSS‑G metal drill designed for precise drilling on Drilling Machines and workshop applications. Short design for increased stability HSS‑G ground for clean metal holes 135° tip for hard materials like stainless steel Fully ground shank for high concentricity Conforms to DIN 338 for short twist drills Faster, more stable drilling for demanding metalwork The short design of this Twist Drill reduces overhang and significantly improves stability during cutting, which leads to more accurate, round holes and less tool wobble. For professionals who require repeatable results, the reduced tendency to bend translates into fewer reworks and a steadier feed. This benefit is especially relevant when working on harder metals where precision is critical. Ground HSS geometry and 135° tip for hard materials Manufactured from HSS‑G and produced with CNC grinding, the flute geometry and cutting edges deliver sharpness and excellent runout accuracy. The 135° tip angle shortens the dwell time on contact and improves centring in tough materials such as stainless steel and tempered alloys. Ground twist drills are easier to re‑sharpen and provide clean chip evacuation, while the Type N normal spiral ensures reliable performance in metal. Built for metal applications and professional workshops This short twist drill is tailored for drilling metal on both stationary and portable Drilling Machines and excels when used on steel, cast iron, non‑ferrous metals and hard plastics. The fully ground shank supports precise clamping and concentricity in the chuck, making it suitable for production runs and sensitive setups. As part of the Profi Line by MetavCUT, the tool targets skilled tradespeople and industrial users who prioritise repeatability and tool life. Efficiency gains and handling recommendations Thanks to the optimised geometry, this short HSS‑G drill can achieve up to 40% faster drilling and requires about 50% less thrust compared with conventional HSS tools under comparable conditions, making operations quicker and less physically demanding. For best results and longer tool life, use appropriate cooling or cutting fluid and avoid excessive overhang. The drill conforms to DIN 338, the standard for short twist drills with cylindrical shanks. Strong recommendation: Choose the MetavCUT Profi Line short Twist Drill for precision metal drilling and consult METAV Werkzeuge for technical advice — they provide expert support and comprehensive guidance to ensure the tool matches your exact needs. Are you unsure whether this Twist Drill meets your requirements or do you need additional technical data? METAV Werkzeuge offers competent consultation: 📧 info@metav-werkzeuge.com ☎️ +49 2822 7131930 ✔️ WhatsApp: +49 170 2837271 Designation: Twist Drill Brand: MetavCUT SKU: 48052-FDA Diameter: 5.2 mm Overall Length: 86 mm Spiral Length: 52 mm Point Angle: 135° Type: Type N Execution: Short Shank Execution: Fully ground Material: HSS‑G Surface/Colour: Bright finished Application: Drills for metal Standard: DIN 338 Model Series: Profi Line Suitable For: Drilling Machine Manufacturer: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What is the main use of a Twist Drill? A Twist Drill from MetavCUT (Type N) is primarily used for machining high‑strength materials and larger drill diameters. The geometry and construction make it suitable for drilling into alloyed and unalloyed steel, cast steel, cast iron, sintered iron, tempered castings, non‑ferrous metals and hard plastics. Its ground design offers sharp edges and precise bore quality while withstanding higher loads. Which three drill types exist? Commonly distinguished drill categories are metal drills, wood drills and masonry/concrete drills. The MetavCUT Twist Drill belongs to the metal drill category and is optimised for those applications. Why are twist drills sharpened at the tip? Sharpening the tip reduces the cross‑cutting edge and lowers friction at the point, which decreases the required thrust force. A correctly ground tip also centres the drill better in the workpiece and improves drilling accuracy. Can a metal drill be used for wood? A metal drill, such as the MetavCUT Twist Drill (Type N), can be used in wood but will typically provide less guidance and a rougher finish than specialised wood drills. Metal drills are easier to re‑sharpen and have less self‑feeding action compared with dedicated wood drills, so results may vary depending on the application and required quality.
5.3mm HSS-G Twist Drill DIN 338 ,short, bright finished, Type N - MetavCUT
Twist Drill – MetavCUT Profi Line, 5.3 mm, Type N, 135°, Short, Bright Finished, HSS‑G, DIN 338 The Twist Drill from MetavCUT is a short, precision metal drill designed for Drilling Machines and characterised by a 135° Tip and HSS‑G construction for demanding metalworking applications. Short HSS‑G Twist Drill for high stability 135° Tip for hard materials like stainless steel Fully ground shank for high concentricity DIN 338 compliant short design Optimised flute length for stationary drilling Precision and Stability for Metalworking The short design delivers significantly improved Stability and reduced deflection compared with longer drills. With a Flute Length of 52 mm and an Overall Length of 86 mm, this short Twist Drill is engineered for applications where rigidity and accurate hole position matter. The reduced overhang minimises vibration on stationary or bench drills, enabling cleaner holes in Alloyed and unalloyed Steel as well as in Gusseisen and non‑ferrous metals. Faster, Cleaner Drilling with Ground HSS Equipped with HSS‑G (ground High Speed Steel) geometry, the drill achieves sharper cutting edges and excellent runout accuracy. Ground drills are ideal when Precision and surface quality are required; they allow up to 40% faster drilling and need less axial force compared to conventional HSS drills. Note: Ground tools can be more brittle than rolled variants and benefit from proper coolant and stationary machine setups. Geometry Optimised for Hard Materials A 135° Tip Angle reduces initial bite and improves centring when working with harder materials such as stainless steel. The Type N (normal spiral) flute design is the classic choice for metal drilling, combining reliable chip evacuation with robust cutting action. For users unfamiliar with the terms: a larger tip angle makes the drill enter the workpiece more gently and helps to avoid chatter when penetrating tough metals. Who Benefits from This Drill Manufactured for professionals and workshops, the Profi Line MetavCUT short twist drill suits machinists who need reproducible, high‑quality holes in demanding materials. It is particularly recommended for precision operations on bench and pillar Drilling Machines where rigidity and concentricity directly impact component fit and finishing operations. Practical Notes on Use The Fully Ground shank ensures excellent concentricity in chucks and collets, improving hole accuracy and surface finish. For best results in harder alloys, use adequate coolant and moderate cutting speeds; the geometry and material combination are optimised for stationary or slow to moderate feeds rather than aggressive, high‑overhang hand‑held drilling. We recommend the MetavCUT Profi Line Twist Drill for precision metalworking tasks — for any technical questions or to confirm suitability for a specific application, METAV Werkzeuge offers comprehensive advice: info@metav-werkzeuge.com | +49 2822 7131930 | WhatsApp: +49 170 2837271 Designation: Twist Drill Brand: MetavCUT SKU: 48053-FDA Type: Type N Diameter: 5.3 mm Tip Angle: 135° Material: HSS‑G Execution: Short Flute Length: 52 mm Overall Length: 86 mm Shank Finish: Fully Ground Colour: Bright Finished For Use With: Drilling Machine Norm: DIN 338 Model Series: Profi Line Manufacturer: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What is a Twist Drill used for? The MetavCUT Twist Drill Type N is primarily used for drilling high‑strength materials and larger diameters; its short form offers greater Stability and precision. The ground geometry makes it suitable for alloyed and unalloyed steel, cast steel, cast iron, sintered iron, malleable iron, non‑ferrous metals and hard plastics, and it withstands higher loads while allowing cleaner, more accurate holes. Which three drill types are there? When choosing tools, consider three main categories: Metal drills (such as the MetavCUT Twist Drill), Wood drills, and Stone/Concrete drills. Each type is optimised for its respective material to ensure best performance and hole quality.
5.4mm HSS-G Twist Drill DIN 338 ,short, bright finished, Type N - MetavCUT
MetavCUT Twist Drill — Type N short, Ø 5.4 mm, HSS‑G, DIN 338, 135° The MetavCUT Twist Drill is a short Type N twist drill for Drilling Machines designed for precise metalworking, offering a 5.4 mm diameter, 135° tip angle and a HSS‑G ground geometry for high accuracy. Short Design for higher Stability 5.4 mm Diameter for precise Metalwork 135° Tip for hard Materials like Stainless Steel HSS‑G Ground for sharp, accurate Holes Conforms to DIN 338 for reliable Standards Faster, More Stable Drilling for Demanding Metalwork Compared with standard lengths, the short design reduces the exposed length of the tool and significantly increases stability and concentricity during operation. This leads to less vibration and more consistent hole quality when machining challenging Materials such as alloyed steel. The combination of fully ground shank and controlled geometry reduces required feed forces, which supports faster cycle times and lowers the risk of runout on both stationary and portable Drilling Machines. Precision Cutting Geometry That Improves Results A 135° tip angle and the ground flute geometry ensure reliable centring and smoother entry into hard Materials. The HSS‑G (ground high‑speed steel) construction produces very sharp cutting edges and high roundness accuracy, resulting in cleaner holes with reduced burr formation. For operators who demand repeatable hole quality, this configuration reduces the need for rework and simplifies downstream processes. Designed for Metal: Materials and Applications Engineered primarily for metalworking, this Type N short Twist Drill is suitable for unalloyed and alloyed steel, cast steel, cast iron, sintered iron, malleable iron, non‑ferrous metals and hard plastics. The tool is especially practical when drilling smaller diameters in tougher Materials where rigidity and accurate guidance are essential. Its specification aligns with DIN 338, which classifies short twist drills with cylindrical shanks and confirms suitability for both stationary and mobile metalworking setups. Practical Advantages in Workshop Use Shorter overall length results in easier handling and reduced deflection during hand‑held or machine work, improving operator confidence and throughput. The ground design (HSS‑G) is straightforward to resharpen when required and gives excellent surface finish in drilled holes. While ground drills tend to be less ductile than rolled equivalents, best practice is to use appropriate coolant and moderate feed rates to prolong tool life and maintain consistent performance. Who Benefits Most from This Tool Ideal for professional metalworkers, toolrooms and repair workshops where precision and repeatability matter, the MetavCUT short Type N Twist Drill supports reliable results in production and maintenance tasks. Engineers and technicians who require fast, predictable penetration in harder Materials will appreciate the reduced feed force and improved centring behavior, which together reduce cycle times and scrap rates. Strong recommendation: Choose the MetavCUT short Type N Twist Drill for demanding metalworking tasks — for tailored technical advice or to confirm suitability for specific jobs, contact METAV Werkzeuge: info@metav-werkzeuge.com | Tel: +49 2822 7131930 | WhatsApp: +49 170 2837271 Designation: Twist Drill Marke: MetavCUT SKU: 48054‑FDA Diameter: 5.4 mm Tip Angle: 135° Type: Type N Execution: short Colour: bright finished Shank: fully ground Material: HSS‑G Spiral Length: 52 mm Overall Length: 86 mm For Drilling Machine: Drilling Machine Model Series: Profi Line Application: Drills for metal Norm: DIN 338 Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ Is the MetavCUT Twist Drill suitable for stainless steel and hardened alloys? The MetavCUT Twist Drill in Type N with a 135° tip and HSS‑G ground geometry is designed to handle harder Materials such as stainless steel and alloyed steels; the larger tip angle improves centring and reduces walking when starting a hole. What are the benefits of the short version of this Twist Drill? A short Twist Drill offers higher stability and less tendency to bend, which produces more precise holes and allows lower feed forces; the short design is therefore well suited to precise workshop and toolroom operations. For what is a Twist Drill used? A Twist Drill, such as the MetavCUT Type N short Twist Drill, is mainly applied when machining high‑strength Materials and larger diameters; its shape is easy to resharpen and it endures substantial loads during metalworking. Which three drill types exist? The three primary drill categories are Metal Drills, Wood Drills and Stone/Concrete Drills; the MetavCUT Twist Drill falls into the Metal Drills category and is optimised for metalworking tasks.
5.5mm HSS-G Twist Drill DIN 338 ,short, bright finished, Type N - MetavCUT
Twist Drill — Type N Short HSS-G (Diameter 5.5 mm, 135° point, Bright Finished) by MetavCUT The Twist Drill is a short Type N HSS-G metal drill designed for high-precision drilling in hard materials with a 5.5 mm diameter and a 135° point angle for improved centring and reduced chipping Short design for enhanced stability and precision Fully ground shank for high Runout accuracy Optimised 135° point for hard metals Conforms to DIN 338 for short twist drills Faster drilling with lower feed force in steel Precision Cutting Power for Hard Materials The Twist Drill in HSS‑G quality offers concentrated cutting performance for demanding metalworking tasks. Its 5.5 mm Diameter combined with a 135° Point Angle reduces the tendency to grab and improves centring in Stainless Steel and other hard alloys. The short overall length minimises overhang and vibration, which results in consistently cleaner Holes and longer tool life when used with appropriate Cutting Fluid. DIN 338 compliance ensures reproducible geometry for industrial and workshop applications. Short Geometry for Greater Stability and Faster Results A reduced Free Length makes this drill far less prone to bending during operation. The Short version with a Spiral Length of 57 mm and a Total Length of 93 mm is particularly suited to operations where stiffness and accuracy matter, including work on lathes, drill presses and hand Drilling Machines. The Fully Ground flute geometry produces sharp cutting edges and excellent Roundness, enabling up to 40% faster drilling and requiring 50% less feed force compared with conventional HSS drills in comparable conditions. Designed for Metalworkers and Precision Workshops This Type N Twist Drill is targeted at professionals and advanced hobbyists who process alloyed and unalloyed Steel, Cast Steel, Cast Iron, Sintered Iron, Non‑Ferrous Metals and Hard Plastics. The typical user benefits from precise hole dimensions and excellent surface finish, especially in materials that demand a 135° tip geometry. For applications that require repeatable accuracy, the Profi Line series by MetavCUT provides robust performance and reproducible results. Correct Use, Sharpening and Material Guidance The 135° Point is specially chosen for harder materials because a larger point angle shortens initial penetration time and improves tool life. Point sharpening reduces the cross‑cut at the tip, lowering friction and necessary feed force while improving centring in the workpiece. HSS‑G (ground high speed steel) stands for very sharp cutting edges and high Roundness, yet it can be more brittle than rolled variants; therefore, secure clamping and coolant are recommended to avoid breakage and to extend service life. Strong recommendation: Choose the MetavCUT Twist Drill Type N short HSS‑G for demanding metal drilling tasks — for personalised advice or further technical data contact METAV Werkzeuge for expert support via eMail: info@metav-werkzeuge.com, Phone: +49 2822 7131930 or WhatsApp: +49 170 2837271 Designation: Twist Drill (Spiralbohrer) Brand: MetavCUT SKU: 48055-FDA Diameter: 5.5 mm Point Angle: 135° Type: Type N Execution: Short Material: HSS-G Colour: Bright finished Shank Finish: Fully ground Spiral Length: 57 mm Total Length: 93 mm Application: Drills for metal Model Series: Profi Line Standard: DIN 338 Suitable For: Drilling Machine (Hand Drilling Machine) Packaging Unit: 10 Manufacturer: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What is a Twist Drill used for and where does the MetavCUT Twist Drill perform best? The MetavCUT Twist Drill (Type N, HSS‑G) is mainly used for machining High‑Strength materials and larger drill diameters; it excels when drilling alloyed and unalloyed Steel, Cast Steel, Cast Iron, Sintered Iron, Non‑Ferrous Metals and Hard Plastics because its geometry and material withstand higher loads while delivering precise holes. Which three main drill types exist? The three common drill categories are Metal drills, Wood drills and Stone/Concrete drills, each optimised in geometry and material for their specific substrate. Why are Twist Drills pointed? Pointing the tip reduces the Cross‑Cut at the Drill’s tip, which lowers friction and required feed force; this sharpening also improves centring in the Workpiece and results in cleaner holes. Can a Metal (HSS) drill be used for wood? A Metal drill can be used in Wood, but the guidance is worse and the hole finish is typically less clean; however, such drills are easier to resharpen and show less self‑pulling into the material than specialised wood drills Are you unsure whether this Twist Drill meets your requirements or need additional technical data? METAV Werkzeuge offers extensive, competent consultation — please contact us by eMail: info@metav-werkzeuge.com, Phone: +49 2822 7131930 or WhatsApp: +49 170 2837271
5.6mm HSS-G Twist Drill DIN 338 ,short, bright finished, Type N - MetavCUT
Twist Drill Type N — short HSS‑G drill, 5.6 mm, 135°, bright finished The Twist Drill Type N short HSS‑G is a precision metalworking drill designed for drilling machines and demanding applications in harder Materials such as Steel and Cast Iron. Twist Drill Type N 5.6 mm, short HSS‑G Fully ground shank for high concentricity 135° Point for hard materials like Stainless Steel DIN 338 compliant short cylindrical drill Short design increases stability and accuracy Faster metalworking with less effort and more control The short Twist Drill in HSS‑G delivers a measurable productivity advantage: CNC‑ground geometry enables up to 40% faster drilling while requiring 50% less feed force compared with conventional HSS drills. This translates into shorter cycle times and reduced operator fatigue when working on alloyed and unalloyed Steel, Cast Steel, Gusseisen, Sintered Iron, and Hard Plastics. For professionals seeking efficient material removal and consistently clean holes, this drill reduces rework and increases throughput without sacrificing hole quality. Greater stability and precision thanks to reduced overhang A shorter overall length means a smaller exposed section from the chuck, which significantly improves stability and reduces deflection under load. In practice this yields straighter holes and better concentricity, particularly when using portable or stationary Drilling Machines. The compact design is ideal for tight setups or when working in jigs and fixtures where control is critical. Users will notice improved repeatability on series work and less vibration on demanding tasks. Geometry engineered for hard materials and clean starts The 135° point angle is chosen to penetrate harder Materials more reliably and to shorten the initial contact time with the workpiece. The Type N (normal spiral) flute geometry is a classic metalworking profile that balances efficient chip evacuation with robust cutting action. Being HSS‑G (ground) means the flutes and cutting edges are formed by grinding, producing very sharp edges and excellent runout accuracy. For less experienced users: grinding (not rolling) produces sharper corners and more precise holes, but requires proper cooling and reduced shock loading to avoid breakage. Recommended uses and suitable operators This short Twist Drill is targeted at professional machinists, maintenance technicians, and metalworking shops that demand accuracy in small to medium diameters. It performs best in metal applications up to medium hardness ranges and is well suited for both stationary machine tools and controlled hand drilling when used with appropriate speeds and coolant. For applications where extreme toughness is needed or frequent impact occurs, consider application‑specific alternatives and consult technical support for selection. I recommend MetavCUT’s Twist Drill Type N as the precision choice for metalworking tasks where stability and fast penetration matter most — for tailored advice or machining parameters contact METAV Werkzeuge at info@metav-werkzeuge.com or call +49 2822 7131930 (WhatsApp +49 170 2837271) Bezeichnung: Twist Drill Marke: MetavCUT SKU: 48056-FDA Durchmesser: 5.6 mm Spitzenwinkel: 135° Typ: Type N Ausführung: short Farbe: bright finished Schaftausführung: fully ground Material: HSS‑G Norm: DIN 338 Gesamtlänge: 93 mm Spirallänge: 57 mm Für Bohrmaschine: Drilling Machine Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What is a Twist Drill best used for and which materials suit it? The MetavCUT Twist Drill Type N is primarily used for metalworking; it is especially effective when machining high‑strength Materials and larger hole diameters. The short HSS‑G design is suitable for alloyed and unalloyed Steel, Cast Steel, Gusseisen, Sintered Iron, Tempered Casts, Non‑Ferrous Metals and Hard Plastics, delivering precise holes and strong cutting performance. Which three basic drill types exist? The main drill types are Metal drills (e.g., the MetavCUT Twist Drill), Wood drills, and Stone/Concrete drills, each optimised in geometry and material for their specific substrate. Why are Twist Drills sharpened at the point? The tip sharpening reduces the cross‑cut at the drill point, which lowers friction and therefore requires less feed force. A properly sharpened MetavCUT Twist Drill centers more easily in the workpiece and cuts with reduced heat and wear. Can one use a metal Twist Drill to drill wood? A metal Twist Drill such as the MetavCUT Type N can be used in Wood, but guidance is reduced and hole finish may be inferior compared with dedicated Wood drills. Metal drills are easier to resharpen and have a lower tendency for self‑feeding, which can be advantageous for controlled drilling. For which drilling depths is the Twist Drill most commonly used? A full‑bore operation into solid material is typically performed with a Twist Drill. For diameters up to about 20 mm and drilling depths up to 100 mm, short or standard Twist Drills are the most frequently used tooling. What is better, HSS or HSSE? There is no universal superiority of HSSE over HSS. When choosing between HSS and HSSE, evaluate whether the specific working conditions—such as higher cutting temperatures or abrasive materials—justify the higher cost of HSSE for your MetavCUT Twist Drill application. If you are unsure whether this Twist Drill meets your requirements or you need additional technical data, METAV Werkzeuge offers extensive, competent advice — please contact us by email at info@metav-werkzeuge.com, by phone at +49 2822 7131930 or via WhatsApp at +49 170 2837271
5.7mm HSS-G Twist Drill DIN 338 ,short, bright finished, Type N - MetavCUT
Das kurze Fazit: Der Spiralbohrer von MetavCUT kombiniert HSS-G-Material und eine geschliffene Schaftausführung zu hoher Stabilität und präziser Bohrung in Metall; der 135° Spitzenwinkel erleichtert das Anbohren harter Werkstoffe und reduziert Ausriss. Bestellen Sie den Spiralbohrer direkt über Metav Werkzeuge oder kontaktieren Sie unsere Beratung bei offenen Fragen. Spiralbohrer kurz von MetavCUT — Profi Line Der Spiralbohrer eignet sich als kurzer HSS‑G Metallbohrer für präzise Bohrungen in legiertem und unlegiertem Stahl sowie Gusswerkstoffen HSS‑G geschliffen für präzise Metallbohrungen Kurze Ausführung für höhere Stabilität 135° Spitzenwinkel für harte Werkstoffe DIN 338 Norm, Zylinderschaft kompatibel Geringere Anpresskraft, bis zu 40 % schnelleres Bohren Robuste Werkstoffwahl sorgt für Durchsatz und Präzision Bei härteren Materialien zahlt sich der Einsatz von HSS‑G aus: Der Schnellarbeitsstahl bietet hohe Schneidfähigkeit und Wärmebeständigkeit, sodass der Bohrvorgang stabil bleibt. Die geschliffene Fertigung sorgt für scharfe Schneiden und eine verbesserte Rundlaufgenauigkeit, was saubere Bohrlöcher ohne übermäßiges Ausbrechen ermöglicht. Daraus resultiert ein sofort spürbarer Produktivitätsvorteil gegenüber ungeformten Walzbohrern. Kürzere Ausführung erhöht Stabilität und Anwendersicherheit Weil die Auskraglänge reduziert ist, verringert sich das Risiko von Verbiegung und Bruch bei stationärem oder maschinellem Einsatz. Die kurze Ausführung ist speziell für stationäre Maschinen und Handbohrmaschinen geeignet, die einen festen Halt gewährleisten. Anwender profitieren von weniger Vibration, gleichmäßigerem Vorschub und damit konstanteren Bohrresultaten. Geometrie und Spitzenwinkel für anspruchsvolle Anwendungen Der 135° Spitzenwinkel wurde gewählt, um das Anbohren in harten Werkstoffen wie Edelstahl oder Temperguss zu erleichtern. Ein größerer Spitzenwinkel reduziert das Wandern auf der Oberfläche und verteilt die Anpresskraft, sodass weniger Vorschub nötig ist. Für Einsteiger: Der Spitzenwinkel beschreibt den Winkel an der Bohrerspitze und beeinflusst, wie schnell und sauber sich der Bohrer in das Material einarbeitet. Einsatzbereiche, Verarbeitung und Maschinenkompatibilität Dieser kurze Spiralbohrer ist nach DIN 338 klassifiziert und mit einem Zylinderschaft ausgestattet, was die Nutzung in handelsüblichen Spannfuttern erleichtert. Er ist geeignet für legierte und unlegierte Stähle, Gussstahl, Gusseisen sowie Nichteisenmetalle und Hartkunststoff. Für tiefergehende oder sehr große Durchmesser empfiehlt sich Mehrstufenaufbohren; für die hier angegebenen Abmessungen ist der Bohrer jedoch für typische Werkstatt‑ und Produktionsaufgaben ausgelegt. Pflegehinweise und Verarbeitungsroutine für längere Standzeit Kühlmittel und regelmäßiges Entgraten verlängern die Lebensdauer dieses Werkzeugs deutlich. Bei geschliffenen HSS‑Bohrern empfiehlt sich vorsichtiges Vorgehen bei Schlagbelastung, um Sprödbruch zu vermeiden. Durch die Kombination aus scharfer Geometrie und geeigneter Kühlschmierstoffzufuhr lässt sich die Standzeit maximieren und Wiederholgenauigkeit sichern. Empfehlung: Den MetavCUT Profi Line HSS‑G Spiralbohrer für präzise Metallbearbeitung direkt über Metav Werkzeuge beziehen — bei Fragen gerne per eMail info@metav-werkzeuge.com oder Telefon +49 2822 7131930 Produktmerkmale Artikelnummer: 48057-FDA Marke: MetavCUT Serie: Profi Line Bezeichnung: Spiralbohrer Ausführung: kurz Fakten Durchmesser: 5,7 mm Gesamtlänge: 93 mm Spirallänge: 57 mm Spitzenwinkel: 135° Verpackungseinheit: 10 Besonderheiten Material: HSS‑G (Schnellarbeitsstahl, geschliffen) Norm: DIN 338 (kurze Spiralbohrer) Schaftausführung: geschliffen (Zylinderschaft) Typ: Typ N (Normalspirale) Farbe: blank Für Bohrmaschine: Handbohrmaschine Hersteller: MetavCUT Modellserie: Profi Line SKU: 48057-FDA Ausführung: kurz Verpackungseinheit: 10 FAQ Für welche Materialien ist der Spiralbohrer von MetavCUT geeignet? Der MetavCUT Spiralbohrer der Profi Line eignet sich besonders für legierten und unlegierten Stahl, Gussstahl, Gusseisen, Nichteisenmetalle und Hartkunststoffe; die HSS‑G Ausführung gewährleistet zuverlässige Leistung bei diesen Werkstoffen. Warum ist die kurze Ausführung vorteilhaft? Die kurze Ausführung reduziert Auskraglänge und erhöht dadurch Stabilität und Rundlaufgenauigkeit, was bei maschinellen Metallbohrungen zu saubereren Ergebnissen mit dem MetavCUT Spiralbohrer führt. Welche Bedeutung hat der 135° Spitzenwinkel? Ein 135° Spitzenwinkel erleichtert das Anbohren von harten Werkstoffen und reduziert das Wandern auf der Oberfläche; das führt bei dem MetavCUT Profi Line Werkzeug zu vereinfachtem Anbohren und weniger Ausriss. Ist der Bohrer kompatibel mit Standardspannfuttern? Ja, der Zylinderschaft entspricht der DIN‑Norm und ist für gängige Spannfutter geeignet; der geschliffene Schaft unterstützt sicheren Halt und gute Ausrichtung. Welche SKU hat der Bohrer und wo kann man weitere technische Daten anfragen? Die SKU lautet 48057-FDA; weitere technische Details und Beratung sind bei Metav Werkzeuge erhältlich, z. B. per eMail info@metav-werkzeuge.com oder Telefon +49 2822 7131930.
5.8mm HSS-G Twist Drill DIN 338 ,short, bright finished, Type N - MetavCUT
Twist Drill — Type N Short HSS‑G, Ø 5.8 mm, 135° Tip, Bright Finished (MetavCUT) A short Twist Drill (Type N) for precision metalworking, designed for use in Drilling Machines and hand drills with a 135° tip for harder materials. Short HSS‑G design for improved stability 135° Tip for drilling harder materials Fully ground shank for excellent concentricity Conforms to DIN 338 for consistent quality Higher Productivity through Short Design and Reduced Feed Force The Twist Drill in a short execution delivers greater rigidity and reduced deflection thanks to its shorter overhang. The HSS‑G ground geometry enables up to 40% faster drilling and requires 50% less feed force compared with conventional HSS variants, resulting in quicker cycle times and less operator effort. This makes the tool particularly effective for demanding metal applications where accuracy and throughput matter. Precise Holes and Better Guidance for Hard Materials A fully ground shank and the Type N normal spiral geometry ensure superior concentricity and clean hole quality. The 135° tip angle is optimised for harder materials such as stainless and alloyed steels, reducing the risk of walking on the surface and shortening plunge time. Compliance with DIN 338 guarantees standardised dimensions and interchangeability for workshop workflows. Designed for Professional Metalworking and Workshop Use This short drill is aimed at machinists, maintenance technicians and professional workshops that require robust, repeatable results in metal. The ground flute geometry makes regrinding straightforward while preserving cutting edges; consequently, the tool offers longevity and simple refurbishment. Use the drill where stable clamping and coolant supply are available to maximise life and hole quality. Practical Handling Tips to Avoid Breakage and Extend Life Because ground short drills can be more brittle than rolled types, operate the tool with appropriate coolant and moderate speeds for the drilled material. Secure Workpiece clamping and minimal overhang are recommended to exploit the stability advantage. For best results in portable hand drills, ensure good axial support and avoid excessive side loads to reduce the risk of fracture. MetavCUT’s short Twist Drill Type N is recommended for precise metal drilling; for personalised advice or additional technical data please contact METAV Werkzeuge — we provide extensive, competent consultation by eMail: info@metav-werkzeuge.com, Phone: +49 2822 7131930, WhatsApp: +49 170 2837271 Designation: Twist Drill Brand: MetavCUT SKU: 48058-FDA Type: Type N Diameter: 5.8 mm Spiral Length: 52 mm Overall Length: 86 mm Tip Angle: 135° Execution: Short Shank Finish: Fully ground Material: HSS‑G Colour / Surface: Bright finished For Machine: Drilling Machine Norm: DIN 338 Model Series: Profi Line Application: Drills for Metal Manufacturer: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What is a Twist Drill used for? The MetavCUT Twist Drill Type N is primarily used for machining high‑strength materials and larger hole diameters; its shape is easy to regrind and it withstands increased loads, making it suitable for demanding metalworking tasks. Which three drill types exist? When comparing drill categories, the main groups are Metal drills, Wood drills and Stone/Concrete (Masonry) drills — the MetavCUT Twist Drill Type N belongs to the metal drill category and is optimised for Ferrous and Non‑ferrous Metals.
5.9mm HSS-G Twist Drill DIN 338 ,short, bright finished, Type N - MetavCUT
Twist Drill (Short, Type N) — 5.9 mm, 135° Tip, HSS‑G, Bright Finished, DIN 338 — MetavCUT Profi Line The Twist Drill (short Type N) is a precision metal drilling tool designed for demanding applications, offering a 135° tip for hard materials and a fully ground HSS‑G construction for clean, accurate holes. Short Design for Increased Stability and Precision 135° Tip Optimised for Hard Metals HSS‑G Ground for Sharp, Clean Holes Fully Ground Cylinder Shank for Accurate Runout High performance for demanding metalworking that reduces cycle times Short construction combined with the HSS‑G material ensures that this Twist Drill delivers faster drilling with lower feed force, particularly in tough alloys. The reduced overhang improves rigidity and significantly lowers the tendency to deflect, which translates into more consistent hole quality and fewer rejects. Users benefit from up to 40% faster penetration in many steels compared with conventional HSS drills and require noticeably less operator effort, making it an efficient choice for production and workshop environments. Robust manufacturing and standards that support precision Manufactured to DIN 338 as a short, ground drill with a cylinder shank, the tool features CNC ground flutes for precise geometry and sharp cutting edges. The designation HSS‑G (ground high‑speed steel) indicates a grinding process that yields very fine cutting edges and excellent runout characteristics; novices should note that ground drills are ideal for precision but may be less tolerant to shock loading than rolled variants. The fully ground shank aids concentricity in chucks and reduces vibration for cleaner holes. Designed application: reliable performance in metals and hard materials This short Type N Twist Drill is optimised for drilling in a wide range of metals including alloyed and unalloyed steels, cast steel, cast iron, sintered iron, malleable iron, non‑ferrous metals and hard plastics. The 135° tip angle shortens the initial biting time on hard workpieces and helps to maintain centre accuracy when starting a hole. For users working with stainless steel or tempered materials, the geometry reduces workhardening at the entry and improves tool life under appropriate cooling conditions. Practical handling advice and recommended use cases Because of its shorter flute length (Spiral Length 52 mm, Overall Length 86 mm) the drill is particularly suitable for stationary and portable drilling where stiffness and repeatability matter. For best results, use moderate cutting speeds, adequate coolant and a stable clamping setup. The ground tip offers excellent centring, but operators should avoid side loads and impact to prevent premature breakage. The bright finished surface facilitates chip evacuation while keeping adhesion of lubricants minimal. Who benefits from this tool and why it stands out Workshops, toolrooms and manufacturers seeking consistent, high‑quality holes in metal will appreciate the balance of stability and cutting speed offered by this short Twist Drill. The MetavCUT Profi Line focuses on repeatability and industrial robustness, making the tool suitable for both prototype work and small‑batch production where accuracy is critical. Its combination of a short design, HSS‑G manufacture and Type N spiral makes it a reliable choice for craftsmen and professionals alike. Strongly recommend the MetavCUT short Twist Drill (Type N) for precision metal drilling — for expert advice contact METAV Werkzeuge at info@metav-werkzeuge.com or call +49 2822 7131930, WhatsApp +49 170 2837271 Designation: Twist Drill Marke: MetavCUT SKU: 48059-FDA Type: Type N Diameter: 5.9 mm Tip angle: 135° Spiral length: 52 mm Overall length: 86 mm Execution: Short Shank finish: Fully ground Material: HSS‑G Colour: Bright Finished Application: Drills for metal Model series: Profi Line Standard: DIN 338 Intended for drilling machine: Drilling Machine (Handbohrmaschine) Packaging unit: 10 Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What is a Twist Drill used for and which materials suit the MetavCUT Type N short Twist Drill? The MetavCUT Twist Drill (short, Type N) is primarily used for drilling metal; it performs especially well in alloyed and unalloyed steels, cast iron, sintered iron, non‑ferrous metals and hard plastics, offering precise holes and improved centring in demanding tasks. Which three drill types exist and how does the MetavCUT Twist Drill relate to them? The three common drill types are Metal Drill, Wood Drill and Masonry/Concrete Drill; the MetavCUT Twist Drill is a Metal Drill of Type N, optimised for metalworking and not intended as a specialist wood or masonry bit.
5mm HSS-G Twist Drill DIN 338 ,short, bright finished, Type N - MetavCUT
Twist Drill 5 mm (Type N) – Short HSS‑G, 135° Tip, Bright Finished, Fully Ground, DIN 338 by MetavCUT The Twist Drill Type N short design is a 5 mm metal drill for Drilling Machines, engineered for precise, stable holes in hard materials such as alloyed and unalloyed steel. Short design for increased stability and precision Fully ground HSS‑G for sharp cutting edges 135° tip angle suited to hard materials DIN 338 compliant for short cylindrical shanks Ideal for professional metalworking and workshop use Precision and Stability for Metalworking The short design of this Twist Drill reduces the unsupported length outside the chuck, which directly increases stability and reduces deflection during drilling. For users who require accurately placed holes in metallic components, the reduced overhang means less vibration and a more concentric hole. This makes the tool particularly suitable for stationary and portable Drilling Machines where repeatability and hole quality matter. Material and Cutting Performance that Saves Effort Made from HSS‑G (ground high speed steel), the Twist Drill delivers very sharp cutting edges and high Runout accuracy after manufacture. The fully ground flute geometry enables up to 40% faster drilling performance and requires around 50% less feed force compared with conventional HSS variants, which benefits operators by lowering effort and tool wear. The 135° tip is optimised for harder materials and shortens initial penetration time while improving centring. Designed for Professional Applications and Materials This Type N Twist Drill is designed primarily for metalworking: alloyed and unalloyed Steel, Cast Steel, Cast Iron, Sintered Iron, Tempered Materials, Non‑Ferrous Metals and Hard Plastics. The short flute length and robust geometry make it the preferred choice for workshops, toolmaking and maintenance departments that demand clean, precise holes and reliable performance under continuous use. The Profi Line model series emphasises durability and consistent results. Handling, Regrinding and Best Practice To achieve best results, use coolant or lubrication when drilling harder metals and operate the Twist Drill at appropriate speeds for the 5 mm diameter. Because the drill is ground rather than rolled, it provides very sharp edges and excellent hole finish but is somewhat more brittle; avoid excessive lateral forces and favour fixed or well‑supported setups. If regrinding is required, maintain the 135° tip geometry to preserve centring behaviour and reduce required feed force. We recommend MetavCUT’s short HSS‑G Twist Drill for precision metalworking — for personalised advice and technical assistance please contact METAV Werkzeuge; Email: info@metav-werkzeuge.com; Phone: +49 2822 7131930; WhatsApp: +49 170 2837271 Technical Details Designation: Twist Drill Brand: MetavCUT SKU: 48050-FDA Diameter: 5 mm Tip Angle: 135° Type: Type N Material: HSS‑G Execution: short Shaft Finish: fully ground Flute (Spiral) Length: 52 mm Overall Length: 86 mm Colour / Surface: bright finished For Use With: Drilling Machine Model Series: Profi Line Standard: DIN 338 Application: Drills for metal Manufacturer: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What is the Twist Drill used for and where does MetavCUT recommend it? The MetavCUT Twist Drill Type N is used primarily for drilling Metal; it excels when making holes in alloyed and unalloyed Steel, Cast Iron and similar hard materials. Its short design improves stability and is recommended for precision workshop and industrial applications. Which three drill bit types exist and how does this Twist Drill fit in? There are three common drill bit categories: Metal Drill Bits, Wood Drill Bits and Masonry/Concrete Drill Bits. The MetavCUT Twist Drill belongs to the Metal Drill Bit group and is engineered for metalworking tasks where a conventional wood or masonry bit would be unsuitable. Why are Twist Drills pointed? The tip sharpening on a Twist Drill reduces the cross‑edge at the point. By pointing, friction is significantly decreased which lowers the required feed force and improves centring of the drill in the workpiece. Can the Twist Drill be used for wood? A Metal Drill Bit such as the MetavCUT Twist Drill can be used in Wood, but guidance and finish are usually inferior compared with dedicated Wood bits. Metal drills are easier to regrind and offer less self‑feeding, so results may be acceptable for non‑critical woodwork.
6.1mm HSS-G Twist Drill DIN 338 ,short, bright finished, Type N - MetavCUT
Twist Drill MetavCUT Profi Line — Type N, 6.1 mm, HSS‑G, Short, 135°, Bright Finished A short MetavCUT Twist Drill Type N for precise metal Drilling Machine work, optimised for hard materials and high stability. Short design for higher stability HSS‑G material for sharp, clean holes 135° tip angle for hard metals Fully ground shaft for superior runout Conforms to DIN 338 for short drills Greater Stability for Accurate Holes Short design reduces the unsupported length of the cutting tool, which directly improves Stability and reduces deflection during machining. The Short 6.1 mm geometry combined with a Fully Ground shaft leads to higher concentricity and cleaner bores when used in a Drilling Machine. As a result, fewer rework operations are required and hole tolerance is easier to maintain. Faster Penetration in Tough Materials Built from HSS‑G, this Short Type N drill achieves up to 40% faster drilling and requires around 50% less feed force compared with conventional HSS drills under comparable conditions. The 135° tip angle is optimised for harder substrates such as stainless steel and tempered alloys, shortening the initial breakthrough time and lowering axial loads on the machine spindle. Precise Application and Recommended Use Designed for metalworking, the Twist Drill Type N excels in drilling Alloyed and Unalloyed Steel, Cast Steel, Cast Iron and Non‑Ferrous Metals. The shortened spiral length limits chatter and makes this drill particularly suited for precise bench, column and stationary machining where coolant can be applied. For manual handfeeding in a Drilling Machine, the improved stability ensures repeatable centre positioning. Manufacturing Quality and Standards for Reliability Produced to DIN 338 as part of the Profi Line, the drill is delivered with a bright finished surface and a ground flute geometry that gives very sharp cutting edges and excellent runout characteristics. Ground flutes (HSS‑G) provide cleaner chips and a defined cutting geometry, though they can be more brittle than rolled variants and therefore benefit from controlled machining parameters and adequate cooling. Strong recommendation: choose the MetavCUT Profi Line short Twist Drill Type N for demanding metal drilling tasks; for advice on suitability, tool parameters or complementary tooling contact METAV Werkzeuge — expert consultation is available by email at info@metav-werkzeuge.com, by phone at +49 2822 7131930 or via WhatsApp at +49 170 2837271 Designation: Twist Drill Brand: MetavCUT SKU: 48061-FDA Diameter: 6.1 mm Spiral Length: 57 mm Overall Length: 93 mm Tip Angle: 135° Type: Type N Execution: Short Shaft Finish: Fully Ground Material: HSS‑G Colour: Bright Finished Model Series: Profi Line Application: Drills for metal Standard: DIN 338 For Drilling Machine: Drilling Machine Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What materials can the MetavCUT Twist Drill Type N be used on? The MetavCUT Twist Drill Type N is primarily specified for metalworking and is suitable for alloyed and unalloyed steel, cast steel, cast iron, sintered iron and non‑ferrous metals; its HSS‑G construction and 135° tip make it particularly effective on harder materials. Is the MetavCUT Twist Drill Type N suitable for handheld drilling? The short configuration and fully ground shaft of the MetavCUT Twist Drill Type N improve stability and centring, so it can be used in hand drilling applications, but best results are achieved with a stationary Drilling Machine and appropriate coolant to avoid undue stress on the tool. For what is a Twist Drill used? A Twist Drill is mainly applied when machining high‑strength materials and larger hole diameters. This form is easy to regrind and withstands higher loads while maintaining good cutting performance. Which 3 drill types exist? The three main drill categories are metal drills, wood drills and masonry/concrete drills. Why are Twist Drills sharpened? Sharpening reduces the cross‑edge at the tip of the Twist Drill, significantly lowering friction and therefore reducing the required feed force; it also improves centring of the tip in the workpiece. Can a metal drill be used in wood? A metal drill can be used in wood, but guidance and finish are usually inferior compared with purpose‑made wood bits; metal drills are easier to regrind and typically have less aggressive self‑feed.
6.2mm HSS-G Twist Drill DIN 338 ,short, bright finished, Type N - MetavCUT
Twist Drill — short HSS‑G Metal Drill, 6.2 mm, 135°, Type N, Bright Finished A short Twist Drill (Type N) designed for precision metalworking and use in drilling machines, offering high stability and fast cutting performance Short design for greater stability and precision HSS‑G material for sharp, durable cutting edges 135° tip angle for harder materials and faster entry Fully ground shank for excellent runout accuracy Precision and Stability for Demanding Metalwork Shorter overall length and a reduced overhang provide significantly higher stability during cutting operations. The combination of a short geometry and a fully ground shank minimises vibration and deflection, so holes remain concentric and tolerances are easier to hold. This design is especially advantageous when machining hard materials or when using smaller diameters, because the stiffer setup reduces the risk of chatter and improves hole quality. Faster Cutting with Lower Feed Force Thanks to the HSS‑G grind and optimized geometry, this drill achieves up to 40% faster drilling rates while requiring around 50% less feed force than conventional HSS tools. The 135° tip angle shortens penetration time in tough alloys and stainless steels by reducing the initial cutting resistance. For users this means quicker cycle times and reduced operator effort, particularly on demanding jobs where efficiency and repeatability matter. Engineered for Metalworking and Machine Use Designed to meet DIN 338, this short twist drill is tailored for metal applications including alloyed and unalloyed steel, cast steels, cast iron, sintered iron, non‑ferrous metals and hard plastics. The Type N normal spiral makes it a versatile choice for conventional metal drilling. Because ground drills can be more brittle than roll‑formed types, it is recommended to use adequate cooling and, where possible, a machine setup rather than hand‑only operation to maximise tool life and prevent breakage. Practical Advice for Safe and Accurate Results When setting up, ensure the drill is clamped securely in a high‑precision chuck and that the workpiece is firmly supported to avoid movement. Start with a suitable pilot or centre drill where needed, and adapt cutting speeds to the material and drill diameter. Regular sharpening of the cutting lips maintains centring behaviour and hole finish; ground HSS tools deliver excellent runout accuracy but benefit from controlled feed and coolant during deep or interrupted cuts. Strong recommendation: choose the MetavCUT Profi Line short Twist Drill for precise, efficient metal drilling — for technical advice or to confirm suitability for your application contact METAV Werkzeuge; we provide expert consultation and comprehensive support. 📧 info@metav-werkzeuge.com ☎️ +49 2822 7131930 ✔️ WhatsApp: +49 170 2837271 Twist Drill Brand: MetavCUT SKU: 48062-FDA Diameter: 6.2 mm Overall length: 93 mm Spiral length: 57 mm Tip angle: 135° Type: Type N Length execution: Short Shank execution: Fully ground Material: HSS-G Standard: DIN 338 Colour: Bright finished For drilling machine: Drilling Machine Application: Drills for metal Model series: Profi Line Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What is a Twist Drill used for? A Twist Drill is primarily used for machining high‑strength materials and larger diameters; it is especially applied to metalworking where robust performance is required. The design is easy to regrind and withstands higher loads, making it a common choice for drilling steels and tougher alloys. Which three drill types are there? The basic categories are Metal drills, Wood drills, and Stone/Concrete drills. Each type features geometry and flutes adapted to its target material to ensure effective chip evacuation and hole quality. Can this Twist Drill be used in hand drills or only in machines? The MetavCUT Profi Line short Twist Drill is optimised for machine use to exploit its stability and precision, but it can be used in a quality handheld drilling machine for light tasks. For heavy or deep drilling in hard materials, a stationary drilling machine and coolant are recommended to avoid excessive stress on the tool. Why are twist drills point‑ground? Point grinding reduces the cross‑edge at the tip, significantly lowering friction so less feed force is required. A ground point also improves centring in the workpiece, leading to more accurate hole positions and smoother drilling starts.
6.3mm HSS-G Twist Drill DIN 338 ,short, bright finished, Type N - MetavCUT
Twist Drill — MetavCUT Profi Line, 6.3 mm, 135°, Type N, Bright Finished, Short HSS‑G, DIN 338 The Twist Drill is a short Type N drill for Drilling Machines, designed for precise metal drilling in demanding industrial and workshop applications. Short design for higher stability HSS‑G ground for sharp cutting edges 135° tip angle for hard materials Fully ground shank for precise concentricity Conforms to DIN 338 for standardised quality Precision and faster drilling for metal components The MetavCUT short Twist Drill with HSS‑G material combines resilient cutting performance with precise geometry. Its 6.3 mm diameter and 135° tip angle reduce entry forces when penetrating hard metals, shortening drilling time and improving hole quality. This design is particularly suitable when drilling stainless steel or alloyed steels, because the larger tip angle helps centre the tool and minimises wandering on the work surface, delivering cleaner, more accurate holes. Short length increases rigidity and accuracy A shorter overall length means less overhang and therefore significantly higher Stability during machining. The reduced cantilever of this short execution lowers bending and chatter, which allows higher feed rates and better surface finish when compared with longer drills. For bench and machine work where runout and concentricity matter, the short Profi Line variant gives reproducible results and reduces the risk of breakage under heavier cutting loads. Ground geometry and material advantages explained The designation HSS‑G indicates a ground High Speed Steel, produced with CNC grinding to form the flutes and cutting edges. This results in very sharp edges and excellent roundness, which translate into precise holes and easier regrinding when required. The fully ground shank ensures accurate clamping and minimises axial runout in standard Drilling Machines. Customers benefit from improved tool life in many metalworking tasks, provided suitable cooling and moderate cutting parameters are used. Built for demanding metalworking tasks This Type N normal‑spiral drill is optimised for a wide range of metallic materials. It is particularly recommended for alloyed and unalloyed steels, cast and ductile irons, sintered metals and non‑ferrous metals, as well as hard plastics. The combination of short design, fully ground shank, and 135° tip supports reliable centring and consistent hole quality, making it a solid choice for toolrooms, maintenance shops and production environments focused on repeatable accuracy. Who should choose this Profi Line short Twist Drill Engineers, machinists and workshop professionals seeking reliable, precise metal drilling will appreciate the balance of speed and robustness offered by this tool. The short Twist Drill suits stationary and light moving machine applications where stability is crucial. For users prioritising easy reconditioning and sharp cut performance, the HSS‑G ground version offers straightforward resharpening and consistent results across repeated operations. Strong recommendation: Choose the MetavCUT Profi Line short Twist Drill for precision metal drilling — for expert, non‑binding advice contact METAV Werkzeuge by eMail: info@metav-werkzeuge.com, Phone: +49 2822 7131930, or WhatsApp: +49 170 2837271 Twist Drill Marke: MetavCUT SKU: 48063-FDA Diameter: 6.3 mm Tip angle: 135° Type: Type N Material: HSS‑G Execution: Short Spiral length: 63 mm Overall length: 101 mm Shank execution: Fully ground Finish/Colour: Bright finished Model series: Profi Line Application: Drills for metal For drilling machine: Drilling Machine Norm: DIN 338 Packaging unit: 10 Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What is the Twist Drill used for? The MetavCUT Twist Drill (Type N) is primarily applied to the machining of high‑strength materials and larger bore diameters. Its short, ground geometry is easier to sharpen and remains durable under greater loads, which makes it suitable for industrial metal drilling where tool resilience and repeatable hole quality are required. Which three drill types exist? When comparing drill categories, there are Metal drills, Wood drills and Stone/Concrete drills. The MetavCUT Twist Drill belongs to the Metal drills group and is engineered specifically for metalworking tasks rather than woodworking or masonry.
6.4mm HSS-G Twist Drill DIN 338 ,short, bright finished, Type N - MetavCUT
MetavCUT Twist Drill — Twist Drill, 6.4 mm, 135°, Type N, Bright Finished, Short, DIN 338, HSS-G A MetavCUT Twist Drill for precision metalworking, the short 6.4 mm Type N cutter delivers stable, fast drilling in hard materials Short design for increased stability and precision 6.4 mm Diameter for accurate metal drilling 135° Tip angle optimised for hard materials HSS-G Material with fully ground geometry Conforms to DIN 338 for standardised quality Engineered for faster, more stable metal drilling The MetavCUT Twist Drill in a short execution combines a compact overall length with a reduced overhang to deliver higher stability and less tendency to deflect. Manufactured from HSS‑G (high speed steel, ground), the bit features a precision ground flute geometry that produces clean holes and reduces cutting forces. The short geometry yields up to 40% faster drilling and requires significantly less feed pressure compared with conventional HSS versions, making it especially suitable for demanding tasks in workshops and production environments. DIN 338 classifies this type of short twist drill with a cylindrical shank, ensuring compatibility with standard chucks and consistent manufacturing tolerances. Optimised tip geometry for hard and alloyed materials A 135° tip angle reduces the initial bite and improves centring in tougher metals such as stainless steel and alloyed steels, shortening contact time and improving tool life. Type N (normal spiral) provides a balanced flute helix suitable for metalworking, while the fully ground shank guarantees excellent concentricity and low runout when mounted in a drilling machine or hand drill. For users less familiar with the terminology: HSS‑G denotes that the cutting geometry is produced by grinding rather than rolling, which results in very sharp cutting edges and high hole quality; however, the ground structure is generally more brittle and benefits from adequate cooling during prolonged operations. Practical benefits, target users and safe handling tips Workshop technicians, maintenance staff and professional machinists will appreciate the combination of short overhang and robust HSS‑G material for producing precise bores in cast iron, sintered parts, non‑ferrous metals and hard plastics. When using the drill in handheld applications, reduced flex leads to fewer broken drills and a more predictable drilling result. To avoid premature breakage, apply moderate pecking cycles on deep holes, use coolant for heat dissipation and clamp workpieces securely. If there is uncertainty whether this cutter matches specific requirements or when additional technical data is needed, Metav Werkzeuge provides extensive and competent advice and support. Strong recommendation: Choose the MetavCUT short HSS‑G Twist Drill (Type N) for demanding metal applications — for expert consultation contact METAV Werkzeuge by eMail at info@metav-werkzeuge.com, by phone at +49 2822 7131930 or via WhatsApp at +49 170 2837271 Technical specifications Designation: Twist Drill Brand: MetavCUT SKU: 48064-FDA Model series: Profi Line Diameter: 6.4 mm Spiral length: 63 mm Overall length: 101 mm Tip angle: 135° Type: Type N Execution: Short Shank execution: Fully ground Finish / Colour: Bright finished Material: HSS-G Application: Drills for metal Suitable for: Drilling Machine / Hand drill Standard: DIN 338 Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What is a Twist Drill used for? The MetavCUT Twist Drill (Type N) is primarily used for machining high‑strength materials and larger bore diameters; its short, ground geometry makes it well suited to precise metalworking. This form is relatively easy to re‑sharpen and withstands significant loads while delivering clean bores, which is why it is often the tool of choice for workshops working with alloyed and unalloyed steel, cast iron and similar materials. Which three drill types are commonly distinguished? In general practice the main drill categories are metal drills, wood drills and stone/concrete drills; the MetavCUT Twist Drill belongs to the metal drill group and is optimised for metalworking tasks.
6.5mm HSS-G Twist Drill DIN 338 ,short, bright finished, Type N - MetavCUT
Twist Drill — Short HSS‑G Metal Drill, 6.5 mm, 135° (Type N, DIN 338, Bright Finished) The Twist Drill is a short HSS‑G drill for Drilling Machines, designed for precise metal drilling and heavy‑duty applications. Short HSS‑G design for demanding metal work Higher stability from reduced overhang and short length 135° tip for efficient entry in hard materials Fully ground shank for high concentricity DIN 338 compliant short twist drill Faster, more stable drilling for metal workpieces The Short Design of this HSS‑G Twist Drill reduces the protruding length from the Chuck, delivering noticeably higher Stability and reduced deflection when drilling into hard alloys. This stability directly improves hole accuracy and roundness, which is essential in workshop and industrial settings where repeatable results matter. Users benefit from lower scrap rates and less rework when tight tolerances are required. Lower feed force and improved penetration in hard materials A 135° Tip Angle combined with the ground geometry allows easier entry into harder materials such as stainless steel. The ground HSS-G geometry reduces the required feed force by up to 50% and can enable up to 40% faster drilling compared with conventional HSS variants. For applications that demand efficient material removal and less operator fatigue, this short Twist Drill offers measurable productivity gains. Precisely ground flute geometry for clean holes The fully ground flutes (HSS‑G) produce sharp cutting edges and excellent concentricity, resulting in clean, burr‑reduced holes and improved surface finish. This benefit is particularly useful when subsequent operations—such as reaming or tapping—rely on a high‑quality pilot hole. Note that ground drills can be more brittle than rolled types, so cooling and steady clamping are recommended for best tool life. Optimised for metal; simple explanation for non‑specialists Type N represents a classic metal Twist Drill spiral, intended for Metal Drilling rather than soft wood or masonry. In practical terms: choose this short HSS‑G drill when working on alloyed or unalloyed steel, cast steel, cast iron, sintered iron, non‑ferrous metals and hard plastics. If drilling in wood or concrete, a different specialist drill type will deliver better guidance and hole quality. Robust standard compliance and practical handling tips Conforming to DIN 338 confirms that this short Twist Drill meets established industry dimensions and shank specifications, simplifying machine setup and toolholder selection. For consistent results: use appropriate coolant, clamp the workpiece securely, and avoid excessive overhang—even though the short length improves rigidity, correct machining practice remains decisive for tool life. Strongly recommended: choose the MetavCUT short HSS‑G Twist Drill for stable, precise metal drilling; for application advice or detailed technical data contact METAV Werkzeuge — expert consultation available by email, phone or WhatsApp at info@metav-werkzeuge.com / +49 2822 7131930 / +49 170 2837271 Technical data Designation: Twist Drill (Short) Brand: MetavCUT SKU: 48065-FDA Diameter: 6.5 mm Tip angle: 135° Type: Type N (Normal Spiral) Execution: Short Overall length: 101 mm Spiral length: 63 mm Shank execution: Fully Ground Material: HSS‑G (Ground High Speed Steel) Surface / Colour: Bright Finished For Drilling Machine: Drilling Machine (Hand Drill compatibility for small tasks) Norm: DIN 338 Application: Drills for Metal Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What is the short Twist Drill best used for? The short Twist Drill from MetavCUT is primarily used for Metal Drilling; its reduced overhang and HSS‑G geometry make it suitable for precise work in alloyed and unalloyed steel, cast components and hard plastics where accuracy and low deflection are required. How does the 135° tip affect drilling performance? A 135° tip on the MetavCUT Twist Drill provides a flatter cutting face that shortens penetration time in harder materials and improves centring for tough steels, making the tool more efficient for industrial metalworking tasks. What are Twist Drills used for Twist Drills are mainly applied when machining high‑strength materials and larger drill diameters. This form is easy to regrind and withstands higher loads, making it suitable for demanding metal cutting work. Which three drill types exist There are three common drill categories: Metal Drills, Wood Drills, Stone/Concrete Drills. Why are Twist Drills sharpened (pointed)? Sharpening the point reduces the cross‑cut at the tip, which significantly lowers friction and the required feed force. At the same time the sharpened point improves centring in the workpiece. Can you use a metal drill in wood? A Metal Drill can be used in Wood, but guidance and finish are inferior compared with dedicated wood bits. Metal Drills are easier to resharpen and have less self‑feeding tendency, resulting in a rougher hole in timber. For which drilling depths is the Twist Drill most used? A solid through hole is typically made with a Twist Drill. For diameters up to 20 mm and drill depths up to 100 mm, the Twist Drill is the most commonly used tool. Is HSS or HSSE better? The general belief that HSSE is always superior to HSS is not universally correct. Evaluate operating conditions carefully to decide whether the higher purchase cost of HSSE is justified for the intended application. If uncertain whether this MetavCUT Twist Drill meets specific requirements or for supplementary technical data, METAV Werkzeuge provides comprehensive and competent advice — contact info@metav-werkzeuge.com, phone +49 2822 7131930 or WhatsApp +49 170 2837271.
6.6mm HSS-G Twist Drill DIN 338 ,short, bright finished, Type N - MetavCUT
Der kurze Spiralbohrer von MetavCUT vereint HSS-G-Schneidstoff, geschliffene Präzision und einen 135° Spitzenwinkel für anspruchsvolle Metallarbeiten. Die kompakte Bauform reduziert Vibrationen und erhöht die Stabilität bei Hand- und stationärem Bohren; dadurch werden saubere Bohrbilder und längere Standzeiten erzielt. Bestellen Sie direkt über Metav oder kontaktieren Sie uns bei Fragen zur Anwendung. Spiralbohrer von MetavCUT — Profi Line, kurzer HSS-G Bohrer Spiralbohrer von MetavCUT, kurze Ausführung, für präzise Bohrungen in Metall bei Hand- und Maschinenbetrieb Kurzversion nach DIN 338 für mehr Stabilität Geschliffener HSS-G für saubere, präzise Bohrungen 6,6 mm Durchmesser, ideal für Standard-Metallarbeiten 135° Spitzenwinkel für härtere Werkstoffe Zylinderschaft für Handbohrmaschine, Gesamtlänge 109 mm Robuste Materialwahl für präzise Metallbearbeitung Der Einsatz von HSS-G als Schneidstoff sorgt für hohe Schneidhaltigkeit und Temperaturbeständigkeit bei Bohrungen in legierten und unlegierten Stahl. Die geschliffene Ausführung führt zu sehr scharfen Schneiden und hoher Rundlaufgenauigkeit, was saubere Bohrbilder ermöglicht. Dieser Vorteil reduziert Nachbearbeitung und erhöht die Effizienz bei wiederkehrenden Metallarbeiten. Kurze Bauform steigert Stabilität und Standzeit Die kurze Ausführung mit reduzierter Auskraglänge minimiert Durchbiegung und Vibration, wodurch Stabilität und Führung bei Handbohrmaschinen sowie stationären Maschinen deutlich verbessert werden. Für Anwender bedeutet das weniger Bruchrisiko und zuverlässigere Ergebnisse, besonders beim Bohren in harten Werkstoffen wie Temperguss oder Gusseisen. Geometrie und Spitzenwinkel für härtere Werkstoffe Der 135° Spitzenwinkel reduziert das Ausbrechen an der Einlaufkante und erleichtert das Anbohren von Edelstahl und hartem Stahl. In Kombination mit der Typ-N-Normalspirale ergibt sich ein ausgewogenes Eindringverhalten, das präzise Zentrierung und kontrollierten Spanabtransport unterstützt. Dadurch lassen sich definierte Bohrpassungen ohne übermäßigen Vorschub erzielen. Anwendungsbereiche und Zielgruppe Konzipiert für den Einsatz in Werkstatt und Industrie eignet sich dieser Bohrer besonders für Metallbearbeitung, Maschineninstandhaltung und Montagearbeiten. Die Ausführung empfiehlt sich für Anwender, die Wert auf Präzision und Wiederholgenauigkeit legen, etwa in der Metallverarbeitung, im Maschinenbau und bei anspruchsvollen Reparaturarbeiten. Hinweise zu Einsatz und Kühlung Bei stationärem Bohren in dichten Werkstoffen empfiehlt sich Kühlung zur Vermeidung von Überhitzung und zur Verlängerung der Standzeit. Durch den geschliffenen Schaft ist der Bohrer für präzise Einsätze vorgesehen; bei Handgebrauch auf festsitzende Spindelaufnahme und kontrollierten Vorschub achten. Eine angemessene Schmierung reduziert Werkzeugverschleiß und sorgt für konstante Bohrergebnisse. Empfehlung: Vertrauen Sie auf die Profi Line von MetavCUT mit HSS-G und kurzer Bauform für stabile, präzise Metallbohrungen — bei Fragen zur Anwendung erreichen Sie uns per E‑Mail unter info@metav-werkzeuge.com oder telefonisch unter +49 2822 7131930 Produktmerkmale Artikelnummer: 48066-FDA Marke: MetavCUT Serie: Profi Line Bezeichnung: Spiralbohrer Typ: Typ N Norm: DIN 338 Material: HSS-G Schaft-Ausführung: geschliffen Farbe: blank Verpackungseinheit: 10 Daten Durchmesser: 6,6 mm Gesamtlänge: 109 mm Spirallänge: 69 mm Spitzenwinkel: 135° Verpackungseinheit: 10 Besonderheiten kurze Ausführung Zylinderschaft Für Bohrmaschine: Handbohrmaschine Anwendung: Bohrer für Metall geschliffen (HSS-G = geschliffen) DIN 338 definiert kurze Spiralbohrer mit Zylinderschaft FAQ Ist dieser Bohrer für Edelstahl geeignet? Der Spiralbohrer von MetavCUT aus HSS-G mit 135° Spitzenwinkel ist gut geeignet für das Anbohren von härteren Werkstoffen wie Edelstahl; bei längeren Bohrungen Kühlung und moderater Vorschub empfehlen. Welche Aufnahme passt für den Schaft? Der geschliffene Zylinderschaft des MetavCUT Spiralbohrers passt in handelsübliche Spannfutter von Handbohrmaschinen und stationären Bohrmaschinen mit entsprechender Aufnahme. Wie viele Bohrer sind in einer Verpackungseinheit? Die Verpackungseinheit enthält 10 Stück; die SKU lautet 48066-FDA und gehört zur Serie Profi Line von MetavCUT. Eignet sich der Bohrer für Blindlöcher und lange Bohrungen? Wegen der kurzen Bauform und der Spirallänge von 69 mm ist der Bohrer besonders für kürzere, präzise Bohrungen geeignet; für tiefe Sacklochbohrungen werden längere Ausführungen empfohlen. Welche Vorteile bietet die geschliffene Ausführung gegenüber gewalzten Bohrern? Geschliffene Bohrer der Serie Profi Line bieten höhere Schärfe und Rundlaufgenauigkeit, was präzisere Bohrungen in Metall ermöglicht; sie können jedoch empfindlicher gegenüber Krafteinleitung sein und profitieren von kontrollierter Anwendung und Kühlung.
6.7mm HSS-G Twist Drill DIN 338 ,short, bright finished, Type N - MetavCUT
Die kurze Ausführung kombiniert Stabilität und Präzision: reduzierte Auskraglänge minimiert das Verbiegen, der HSS-G-Werkstoff sorgt für scharfe Schnittkanten, und der Spitzenwinkel von 135° erleichtert das Anbohren harter Werkstoffe. Bestellen Sie den Spiralbohrer direkt über Metav oder fragen Sie unsere Beratung an, wenn Sie spezifische Anwendungen planen. Spiralbohrer — kurzer HSS-G-Bohrer für Metall Der Spiralbohrer in kurzer Ausführung für präzise Metallbohrungen mit geschliffener Geometrie und Zylinderschaft MetavCUT Profi Line Spiralbohrer Kurze Ausführung für höhere Stabilität beim Bohren Material HSS-G (geschliffen) für präzise Bohrungen Spitzenwinkel 135° für harte Werkstoffe Geeignet für Handbohrmaschine und Werkstattbetrieb Kompakte Bauform erhöht Standfestigkeit und Präzision Die kurze Ausführung reduziert die Auskraglänge und verbessert dadurch die Stabilität beim Bohren. Das führt zu weniger Vibrationen und geringerer Neigung zum Verbiegen, was besonders bei Bohrungen in Stahl oder Gusseisen die Qualität der Bohrung erhöht. Anwender profitieren von saubereren Bohrlöchern und höherer Wiederholgenauigkeit bei stationärer oder handgeführter Bearbeitung. Materialwahl und Schneidverhalten für Metallbearbeitung Der Einsatz von HSS-G kombiniert Härte und Schnitthaltigkeit mit hoher Oberflächengüte durch CNC-Schliff. Die geschliffene Geometrie erzeugt scharfe Kanten, die saubere Späne und präzise Bohrbilder ermöglichen. In Verbindung mit dem Spitzenwinkel 135° eignet sich diese Ausführung besonders für legierte und unlegierte Stähle sowie für Edelstahl, da das Anbohren erleichtert wird und das Werkzeug stabiler in harten Werkstoffen arbeitet. Kompatibilität mit Werkzeugen und typischen Anwendungen Dieser Bohrer ist für Anwendungen im Standard-Bereich konzipiert und eignet sich für Werkstatt, Montage und DIY-Projekte. Die Kombination aus Zylinderschaft und robuster Ausführung erlaubt die Nutzung in Handbohrmaschine und stationären Maschinen. Für hochpräzise Passungen sollte jedoch vor dem Bohren angesenkt oder mit einem Zentrierbohrer gearbeitet werden, um ein Wandern des Bohrers zu vermeiden. Verarbeitungsempfehlungen und praktische Hinweise Bei der Verwendung von geschliffenen Bohrern empfiehlt sich der Einsatz von Kühlschmierstoff, insbesondere bei zähen oder wärmeleitfähigen Werkstoffen, um Überhitzung und vorzeitigen Verschleiß zu vermeiden. Die geschliffen Ausführung liefert hohe Rundlaufgenauigkeit, ist jedoch empfindlicher gegen seitliche Belastung als walzgefertigte Bohrer; deshalb ist ruhige Führung und geeignete Aufnahme wichtig für eine lange Werkzeugstandzeit. Empfehlung: Für präzise Metallbohrungen die MetavCUT Profi Line HSS-G Kurzvariante wählen und bei Metav anfragen — eMail: info@metav-werkzeuge.com / Telefon: +49 2822 7131930 Produktmerkmale Artikelnummer: 48067-FDA Marke: MetavCUT Serie: Profi Line Bezeichnung: Spiralbohrer Zahlen Durchmesser: 6,7 mm Gesamtlänge: 109 mm Spirallänge: 69 mm Spitzenwinkel: 135° Verpackungseinheit: 10 Besonderheiten Material: HSS-G (geschliffen) Schaftausführung: geschliffen, Zylinderschaft Norm: DIN 338 Typ: Typ N Farbe: blank Für Bohrmaschine: Handbohrmaschine Ausführung: kurz FAQ Für welche Materialien ist dieser Bohrer geeignet? Der MetavCUT Profi Line Spiralbohrer mit HSS-G eignet sich für legierte und unlegierte Stähle, Gussstahl, Gusseisen, Sintereisen sowie Nichteisenmetalle und Hartkunststoffe und bietet dabei saubere Bohrbilder. Ist der Bohrer für die Nutzung in einer Handbohrmaschine geeignet? Ja, die kurze Ausführung des MetavCUT Profi Line Spiralbohrers wurde speziell für den Einsatz in Handbohrmaschine und Werkstatt entwickelt und reduziert die Neigung zum Verbiegen. Was bedeutet HSS-G und welchen Vorteil bietet es? HSS-G steht für geschliffenen Schnellarbeitsstahl; die geschliffene Geometrie sorgt für sehr scharfe Schneidkanten und hohe Rundlaufgenauigkeit, was präzise Bohrungen in harten Werkstoffen ermöglicht. Warum ist der Spitzenwinkel 135° wichtig? Ein Spitzenwinkel von 135° erleichtert das Anbohren harter Werkstoffe und verringert das Fransen beim Eintritt; das verbessert die Bohrbildqualität insbesondere in Edelstahl und gehärteten Stählen. Entspricht der Bohrer einer Norm und welche Ausführung ist das? Der Spiralbohrer erfüllt die Norm DIN 338 und ist in kurzer Ausführung mit Zylinderschaft gefertigt, was ihm höhere Stabilität und Eignung für präzise Metallbohrungen verleiht.
6.8mm HSS-G Twist Drill DIN 338 ,short, bright finished, Type N - MetavCUT
Kombination aus kurzer Ausführung, HSS‑G Geschliffen und 135° Spitzenwinkel sorgt für schnelle, präzise Metallbohrungen und reduziert die Anpresskraft deutlich; bestellen Sie den Spiralbohrer direkt über Metav oder fragen Sie unsere Beratung bei Bedarf an. Spiralbohrer 6,8 mm HSS‑G, kurz – Profi Line von MetavCUT Der Spiralbohrer 6,8 mm in kurzer Ausführung für stabile und präzise Metallbohrungen auf stationären und handgeführten Maschinen 6,8 mm HSS‑G, geschliffen Kurze Ausführung für höhere Stabilität Spiralänge 69 mm für präzise Führung 135° Spitzenwinkel für harte Werkstoffe Norm DIN 338, Typ N für Metall Präzise Bohrungen durch geschliffene HSS‑Geometrie Die geschliffene HSS‑G‑Geometrie sorgt für sehr scharfe Schneiden und hohe Rundlaufgenauigkeit, was besonders bei Metallbohrungen zu sauberen, maßhaltigen Löchern führt. Durch den CNC‑Schliff entstehen definierte Spanräume, die das Bohrbild verbessern und die Standzeit unter geeigneter Kühlung erhöhen. Anwender profitieren von bis zu 40 % schnellerem Bohren und 50 % geringerer Anpresskraft gegenüber konventionellen HSS‑Bohrern, was die Ermüdung bei Serien‑ oder Montagearbeiten reduziert. Stabilität und Führungsgenauigkeit durch kurze Auskraglänge Die kurze Ausführung bedeutet eine geringere Auskraglänge aus dem Bohrfutter, wodurch Verwölbung und Schwingungen minimiert werden. Das Ergebnis ist eine höhere Stabilität beim Zentrieren und weniger Neigung zum Verbiegen, insbesondere beim Bohren in harten Materialien wie legiertem Stahl oder Gusseisen. Diese Eigenschaft macht den Bohrer zur ersten Wahl, wenn es auf präzise Passungen und saubere Bohrkanten ankommt. Praktische Einsatzbereiche und Maschinenkompatibilität Der Bohrer eignet sich für die Bearbeitung von legierten und unlegierten Stählen, Gussstahl, Gusseisen, Sintereisen, Temperguss, Nichteisenmetallen und Hartkunststoff. Er kann sowohl auf stationären Säulenbohrmaschinen als auch auf hochwertigen Handbohrmaschinen eingesetzt werden; bei Handanwendung empfiehlt sich Anpunkten zur Führung. Die Auslegung als Typ N (Normalspirale) macht ihn robust und vielseitig für allgemeine Metallarbeiten. Material, Norm und Besonderheiten der Ausführung Die Fertigung nach DIN 338 garantiert die Klassifizierung als kurzer Spiralbohrer mit Zylinderschaft. Der Schaft geschliffen ermöglicht eine präzise Spannaufnahme, die Spirallänge von 69 mm unterstützt eine kontrollierte Spanabfuhr bei mittleren Bohrtiefen, und der 135° Spitzenwinkel erleichtert das Anbohren harter Werkstoffe. Durch die kurze Gesamtlänge ergibt sich eine hohe Führungsstabilität für maßhaltige Ergebnisse. Empfehlung: Setzen Sie auf den MetavCUT Spiralbohrer in HSS‑G für anspruchsvolle Metallbohrungen; bei offenen Fragen erreichen Sie unsere Beratung per E‑Mail info@metav-werkzeuge.com oder telefonisch unter +49 2822 7131930. Produktmerkmale Bezeichnung: Spiralbohrer Hersteller: MetavCUT Serie: Profi Line Artikelnummer: 48068-FDA Daten Durchmesser: 6,8 mm Gesamtlänge: 109 mm Spiralänge: 69 mm Spitzenwinkel: 135° Verpackungseinheit: 10 Besonderheiten Material: HSS‑G — geschliffen (CNC‑Schliff, hohe Rundlaufgenauigkeit) Schaftausführung: geschliffen Ausführung: kurz Typ: Typ N — Normalspirale, geeignet für Metall Farbe: blank Für Bohrmaschine: Handbohrmaschine Norm: DIN 338 — Klassifikation kurzer Spiralbohrer FAQ Ist der Bohrer für Edelstahl geeignet? Der Spiralbohrer von MetavCUT in HSS‑G mit 135° Spitzenwinkel eignet sich für härtere Werkstoffe und kann unter geeigneter Kühlschmierstoffzufuhr auch für Edelstahl eingesetzt werden; bei sehr zähem Werkstoff sind spezielle Beschichtungen empfehlenswert. Kann der Bohrer in einer Handbohrmaschine verwendet werden? Ja, die kurze Ausführung und der Zylinderschaft erlauben den Einsatz an Handbohrmaschinen, wobei ein Anpunkten zur Führung empfohlen wird; für optimale Ergebnisse empfiehlt sich eine leistungsfähige Maschine mit ruhigem Rundlauf. Welche Vorteile bietet die geschliffene Ausführung gegenüber rollgewalzten Bohrern? Geschliffene HSS‑G‑Bohrer bieten schärfere Schneiden und höhere Rundlaufgenauigkeit, was zu saubereren Bohrbildern und präziseren Ergebnissen in Metall führt; sie sind jedoch empfindlicher gegen Verkantung und daher eher für stationäre oder kontrollierte Anwendungen geeignet. Worauf ist bei der Anwendung dieses Spiralbohrers zu achten? Beim Einsatz des Spiralbohrers 6,8 mm von MetavCUT sollte auf angemessene Kühlung und eine kontrollierte Vorschubgeschwindigkeit geachtet werden; bei tiefen Bohrungen sind Zwischenspülungen oder mehrstufiges Aufbohren sinnvoll. Welche technischen Angaben weist die SKU 48068-FDA aus? Die SKU 48068-FDA bezeichnet den Spiralbohrer 6,8 mm aus der Profi Line von MetavCUT, gefertigt in HSS‑G, kurze Ausführung, geschliffener Schaft, DIN 338, geeignet für Metallanwendungen.
6.9mm HSS-G Twist Drill DIN 338 ,short, bright finished, Type N - MetavCUT
Twist Drill (Type N) short HSS-G Ø 6.9 mm, 135°, bright finished The Twist Drill Type N short HSS-G is a precision metal‑drilling tool for handheld and machine applications, designed for stable, fast and accurate holes in hard materials. Short Design for higher Stability HSS‑G ground for sharp edges and precision 135° Tip for hard metals and stainless steel Fully Ground shank for excellent concentricity Conforms to DIN 338 for short twist drills Engineered for faster, more stable metal drilling Thanks to its short design, this Twist Drill offers a reduced overhang that significantly improves stability and lowers the risk of bending during operation. The HSS‑G ground geometry enables up to 40% faster drilling while requiring around 50% less feed force compared with conventional HSS variants, which means less operator effort and higher productivity for repetitive or demanding metal‑working tasks. Ideal for precise holes where runout and wobble must be minimised. Precision through fully ground construction This drill is produced with a fully ground flute geometry (HSS‑G), a manufacturing method that creates very sharp cutting edges and high concentricity. Ground Twist Drills deliver cleaner, more accurate holes and improved surface quality in metals. Note that ground tools can be somewhat more brittle than rolled versions, so coolant use and reduced overhang are recommended for long tool life and consistent results. Geometry tailored to hard materials and accuracy A 135° tip angle reduces entry forces and is optimised for harder workpiece materials such as stainless and alloyed steels. The classic Type N normal spiral is purpose‑built for metal drilling and ensures reliable chip removal and cutting action. Dimensions: Diameter 6.9 mm, Spiral Length 69 mm, Overall Length 109 mm, providing a compact yet effective form factor for demanding applications. The product meets DIN 338, the standard for short twist drills with cylindrical shanks. Practical application and machine compatibility Designed primarily for Drilling Machines and handheld drills where precision and stability are required, this short Twist Drill from the Profi Line is suitable for alloyed and unalloyed steels, cast materials and hard plastics. The bright finished surface and fully ground shank support excellent clamping in chucks and reduce runout. For best results in tougher materials, use appropriate coolant and avoid excessive overhang to prevent breakage and ensure repeatable hole quality. Opt for the MetavCUT short Type N Twist Drill for demanding metal‑working tasks — METAV Werkzeuge offers expert technical advice and support via info@metav-werkzeuge.com, Tel +49 2822 7131930, WhatsApp +49 170 2837271 Designation: Twist Drill Brand: MetavCUT SKU: 48069-FDA Type: Type N Diameter: 6.9 mm Spiral Length: 69 mm Overall Length: 109 mm Tip Angle: 135° Material: HSS-G Shank Execution: Fully Ground Execution: short Colour: bright finished For Drilling Machine: Drilling Machine Application: Drills for metal Model Series: Profi Line Norm: DIN 338 Manufacturer: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ For what is a Twist Drill used? The MetavCUT Twist Drill Type N short is primarily used for machining high‑strength materials and larger diameters; its design makes it easy to resharpen and able to withstand higher loads, which is why it is favoured for metalworking and demanding drilling tasks. Which three drill types exist? Commonly distinguished drill types are Metal Drill, Wood Drill and Masonry/Concrete Drill, and the MetavCUT Twist Drill belongs to the metal drill category optimised for steel and similar materials.
6mm HSS-G Twist Drill DIN 338 ,short, bright finished, Type N - MetavCUT
Spiralbohrer – HSS‑G Kurzspiralbohrer (MetavCUT Profi Line) Spiralbohrer von MetavCUT in kurzer Ausführung für präzise Metallbohrungen an Hand‑ und stationären Maschinen. HSS‑G Spiralbohrer von MetavCUT Profi Line Kurze Ausführung für höhere Stabilität Geschliffener Zylinderschaft für hohe Rundlaufgenauigkeit 135° Spitzenwinkel für harte Werkstoffe Geeignet für Handbohrmaschine und stationäre Maschinen Mehr Stabilität und präzision bei harten Werkstoffen Die kurze Ausführung reduziert die Auskraglänge und erhöht dadurch die Stabilität während des Bohrens. Durch die verringerte Neigung zum Verbiegen ergeben sich saubere Bohrbilder und geringere Ausschussraten bei legierten und unlegierten Stählen. Kombination aus kurzer Geometrie und geschliffener Fertigung sorgt für eine definierte Spanbildung und reduziert Vibrationen bei der Bearbeitung. Material und Fertigung für längere Standzeit und saubere Löcher Der HSS‑G Werkstoff bietet eine ausgewogene Härte und Zähigkeit, ideal für die Metallbearbeitung. Die geschliffene Ausführung ermöglicht scharfe Schneiden und hohe Rundlaufgenauigkeit, was insbesondere beim Bohren in Gusseisen, Temperguss und Sintereisen zu präziseren Ergebnissen führt. Der Einsatz von Kühlmittel wird empfohlen, um Wärmeentwicklung zu begrenzen und die Standzeit weiter zu erhöhen. Geometrie und Anwendungen: Wie die Technik den Vorteil liefert Der 135° Spitzenwinkel reduziert das Aufreißen beim Anbohren härterer Werkstoffe und verkürzt die Anbohrphase, was die Bearbeitungszeit senkt. Als Typ N Normalspirale eignet sich der Bohrer besonders für klassische Metallanwendungen; die DIN‑Konformität nach DIN 338 garantiert definierte Maße und Austauschbarkeit in der Werkstatt. Für Arbeiten an dünnen Blechen empfiehlt sich zudem ein Vorstechen, um Wandern zu vermeiden. Einsatzempfehlungen und sichere Handhabung Der Spiralbohrer ist primär für den Einsatz an Hand‑ und stationären Bohrmaschinen ausgelegt; bei Handgeräten vermeidet die kurze Bauform Überlast und verbessert die Kontrolle. Für tiefe Bohrungen empfiehlt sich stufenweises Arbeiten, bei größeren Durchmessern Vorbohren. Kühlung, moderater Vorschub und passende Drehzahlen erhöhen die Effizienz und verringern Bruchrisiken bei der spröderen geschliffenen Ausführung. MetavCUT Profi Line HSS‑G Kurzspiralbohrer empfehlen: Für präzise Metallbohrungen direkt technische Beratung beim Metav‑Qualitätsfilter in Emmerich anfragen: info@metav-werkzeuge.com oder telefonisch +49 2822 7131930. Produktmerkmale Artikelnummer: 48060-FDA Marke: MetavCUT Serie: Profi Line Typ: Typ N Norm: DIN 338 Verpackungseinheit: 10 Fakten Durchmesser: 6 mm Gesamtlänge: 93 mm Spirallänge: 57 mm Spitzenwinkel: 135° Besonderheiten Material: HSS‑G (Schnellarbeitsstahl, geschliffen) Ausführung: kurz Schaft Ausführung: geschliffen (Zylinderschaft) Für Bohrmaschine: Handbohrmaschine und stationäre Maschinen Farbe: blank FAQ Welche Materialien lassen sich mit dem Spiralbohrer von MetavCUT bearbeiten? Der MetavCUT Profi Line Spiralbohrer aus HSS‑G eignet sich für legierte und unlegierte Stähle, Gussstahl, Gusseisen, Sintereisen, Temperguss, Nichteisenmetalle und Hartkunststoffe; bei härteren Werkstoffen empfiehlt sich Kühlung. Ist die kurze Ausführung für handgeführte Bohrarbeiten geeignet? Ja, die kurze Ausführung reduziert Auslenkung und verbessert die Handhabung an Handbohrmaschinen; trotzdem sind moderater Vorschub und passende Drehzahlen wichtig, um Bruch zu vermeiden. Warum ist die geschliffene Fertigung vorteilhaft? Geschliffene Spiralbohrer (HSS‑G) bieten scharfe Schneiden und hohe Rundlaufgenauigkeit, was zu sauberen Bohrlöchern und weniger Nacharbeit führt; Einsatz an stationären Maschinen erhöht die Zuverlässigkeit. Welche Rolle spielt der 135° Spitzenwinkel? Der 135° Spitzenwinkel verringert das Auftreten von Aufreißen beim Anbohren harter Werkstoffe und verkürzt die Anbohrzeit, was die Effizienz bei Edelstahl und gehärteten Stählen verbessert. Welche Normen und Bezeichnungen hat der Bohrer? Der Spiralbohrer entspricht der DIN 338 und wird in der MetavCUT Profi Line geführt; die Artikelnummer lautet 48060-FDA, was die einfache Identifikation im Lager ermöglicht.
7.1mm HSS-G Twist Drill DIN 338 ,short, bright finished, Type N - MetavCUT
Introducing Twist Drill — MetavCUT Profi Line short HSS‑G Type N, 7.1 mm, 135° (bright finished) The Twist Drill is a short HSS‑G Type N drill designed for precise metal drilling, offering improved stability and fast cutting in demanding workshop and industrial applications. Short design for increased stability and precision HSS‑G ground geometry for sharper cutting edges 135° point angle tailored for hard metals and stainless steel Fully ground shank for excellent runout accuracy Conforms to DIN 338 for short cylinder‑shank twist drills Engineered for faster, more stable metal cutting The Profi Line short Twist Drill combines a short length with a ground HSS geometry to reduce vibration and deflection during drilling. This design means higher stability and a lower tendency to wander, so holes remain concentric and true. The ground HSS (HSS‑G) material produces very sharp cutting edges that can achieve up to 40% faster drilling while requiring around 50% less feed force versus conventional HSS drills, which is especially advantageous when machining tougher alloys or thicker sections. Geometry that adapts to hard materials and reduces set‑up time A 135° point angle reduces the tendency to rub at the tip and shortens penetration time in hard materials such as stainless steel. The Type N normal spiral provides a balanced flute geometry that evacuates chips reliably while maintaining cutting stability. The fully ground flutes and shank ensure high runout accuracy, which simplifies set‑up on both stationary drill presses and portable drilling machines and results in cleaner, more precise holes. Designed for professional workshops and demanding applications This short Twist Drill suits machinists, toolroom technicians and maintenance teams who require repeatable accuracy on metal components. Its shorter overhang minimises bending moments, making it ideal for precision work in confined fixtures or jigs. The drill is primarily intended for metalworking tasks including alloyed and unalloyed steel, cast steel, cast iron, sintered iron, malleable cast iron, non‑ferrous metals and hard plastics. Practical handling, grinding and cooling recommendations Because the HSS‑G ground variant favours sharpness and accuracy, it can be more brittle than rolled alternatives; appropriate coolant and moderate feed rates are recommended for prolonged tool life. Ground flutes allow straightforward re‑grinding when required, so maintenance is simple in a well‑equipped workshop. Use steady clamping and, for best results, prefer machine drilling where coolant and rigid fixturing are available to exploit the drill’s full performance. Choose the MetavCUT Profi Line short Twist Drill for precise, stable metal drilling — for technical questions or to ensure the drill matches your application, METAV Werkzeuge provides expert advice and support: info@metav-werkzeuge.com | +49 2822 7131930 | WhatsApp +49 170 2837271 Designation: Twist Drill Brand: MetavCUT SKU: 48071-FDA Type: Type N (Normal Spiral) Diameter: 7.1 mm Point Angle: 135° Overall Length: 109 mm Spiral Length: 69 mm Execution: short Shank Finish: fully ground Material: HSS-G (ground high‑speed steel) Colour / Surface: bright finished Intended For: Drilling Machine / Hand Drills Model Series: Profi Line Standard: DIN 338 Manufacturer: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What are Twist Drills used for? Twist Drills such as the MetavCUT Profi Line short Twist Drill are primarily used for machining high‑strength materials and larger drill diameters; their ground form is easy to re‑sharpen and can withstand higher loads, making them a reliable choice for metalworking applications. Which three drill types exist? The main categories are metal drills (for steel and alloys), wood drills (for timber and similar materials), and stone/concrete drills (for masonry and concrete).
7.2mm HSS-G Twist Drill DIN 338 ,short, bright finished, Type N - MetavCUT
Twist Drill — Short HSS‑G Spiral Drill, 7.2 mm, 135° (Type N) The Twist Drill is a short Type N HSS‑G drill designed for precise metal drilling, featuring a 7.2 mm diameter and a 135° tip angle for demanding applications. Short design for increased stability HSS‑G ground for precise metal holes 135° tip for hard materials like stainless steel Fully-ground shank for accurate concentricity DIN 338 compliant professional standard Engineered for higher precision and reduced vibration Built with a short overall length and a reduced overhang, this HSS‑G Twist Drill minimises bending and vibration to deliver more accurate bores in metal. The fully-ground geometry produces sharp cutting edges and superior runout characteristics, which means cleaner holes and less rework. For workshop setups and stationary machines where concentricity matters, this construction offers a measurable advantage in repeatability and tool life. Optimised for hard metals and efficient cutting The 135° tip angle and the Type N normal spiral make this drill particularly suitable for tougher materials such as alloyed and unalloyed steel. Thanks to the ground HSS composition, drilling speeds can be increased while maintaining edge stability; in practical terms this often results in up to 40% faster drilling with significantly lower feed force compared to conventional HSS designs. The short flute length also aids coolant penetration and chip evacuation during deeper operations. Practical use, handling and recommended applications For precise work on steel, cast materials and non-ferrous metals, this Twist Drill from the MetavCUT Profi Line is intended for use in Drilling Machines and hand drills where a short, rigid setup is possible. The fully-ground shank ensures secure chucking and improved concentricity for finishing operations. Users looking for professional results in manufacturing, maintenance or toolrooms will appreciate the balance of stability and cutting performance offered by this design. For professional results choose MetavCUT’s short Twist Drill — contact METAV Werkzeuge for technical advice and tailored recommendations via eMail: info@metav-werkzeuge.com, Phone: +49 2822 7131930 or WhatsApp: +49 170 2837271 Designation: Twist Drill Marke: MetavCUT SKU: 48072-FDA Diameter: 7.2 mm Tip Angle: 135° Type: Type N Execution: Short Overall Length: 109 mm Spiral Length: 69 mm Material: HSS‑G Shank Finish: Fully ground Colour: Bright finished For Drilling Machine: Drilling Machine Application: Drills for metal Model Series: Profi Line Norm: DIN 338 Manufacturer: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What is a Twist Drill used for? A Twist Drill from MetavCUT (Type N) is primarily used for machining high-strength materials and larger drill diameters; its geometry is easy to regrind and it withstands substantial loads. The design excels when drilling alloyed and unalloyed steel, cast steel, cast iron, sintered iron, malleable iron, non-ferrous metals and hard plastics. Which three drill types are there? Commonly distinguished drill types are metal drills, wood drills and masonry/concrete drills; the MetavCUT Twist Drill belongs to the metal drill category and is optimised for steel and similar materials. Can I use a metal Twist Drill for wood? A metal Twist Drill such as the MetavCUT Type N can be used in wood but will typically offer inferior guidance and a less clean finish than a dedicated wood drill. Metal drills are easier to regrind and produce less aggressive self-feeding, which can be acceptable for rough woodworking tasks.
Precision centring for clean, repeatable holes
The HSS‑G twist drill DIN 338 type N, short, ground, uncoated, 135° split point is a universal production drill engineered for demanding workshop and industrial tasks. Also described as a high-speed steel twist drill or ground twist drill, it combines accurate centring with excellent chip evacuation for process-secure drilling.
Where this drill makes a measurable difference
Designed to be used directly in production settings, the drill’s ground profile is machined from solid HSS, not roll-formed, which delivers superior concentricity and razor-sharp cutting edges. The flat 135° split point with cross grind centres the drill on contact, so the usual pre‑punching step can be omitted. That reduces set-up time, lowers drilling force and prevents walking on smooth surfaces, making it ideal for series work and delicate fixturing.
Concrete benefits for daily use
- Faster set-up and higher first-pass accuracy thanks to the 135° split point.
- Improved hole quality and dimensional consistency from the ground HSS profile.
- Reduced chip adhesion and smoother flute flow with the uncoated (blank) surface, especially on aluminium and plastics.
- Lower drilling force and less tool deflection for thin sheets and non-ferrous materials.
- Versatile application across common workshop materials while maintaining process reliability.
Metav as a practical precision partner
Metav combines decades of application expertise with a focused European supply chain from Emmerich. With more than 48,000 customers and a broad range of workshop and metrology supplies, Metav offers this HSS‑G twist drill as part of a pragmatic range that balances reliability and accessibility. The combination of product knowledge and dependable logistics supports uninterrupted production and sensible purchasing decisions.
Technical data
- Standard: DIN 338
- Type: type N (short)
- Material: ground from solid high-speed steel (HSS)
- Coating/surface: uncoated (blank)
- Point geometry: 135° split point with cross grind
- Profile: ground flutes, razor-sharp cutting edges, high concentricity
- Typical applications: steel; iron; sheet metal; non-ferrous metals; aluminium; various plastics
- Operational advantages: self-centring; reduced need for centre‑punching; improved chip evacuation; lower drilling force
FAQ
Is the HSS‑G twist drill suitable for aluminium and plastics?
The HSS‑G twist drill is well suited to aluminium and many plastics. Its uncoated, blank surface reduces friction and helps chips evacuate cleanly so material build-up on the cutting edge is minimised.
Can I omit centre‑punching with this drill?
Yes. The 135° split point with cross grind self‑centres on contact, which typically removes the need for separate centre‑punching and reduces the risk of the drill walking.
How does a ground twist drill differ from roll‑formed drills?
A ground twist drill is machined from solid HSS, providing better concentricity, sharper cutting edges and smoother flutes compared with roll‑formed alternatives, resulting in higher hole quality and longer reliable performance.
What does type N mean in DIN 338?
Type N indicates the short series as defined in DIN 338, making this configuration compact for stable, controlled drilling in workshop and industrial applications.
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com