Durable indexable inserts for efficient metalcutting
Indexable inserts are hardened cutting elements designed to deliver consistent material removal in metalworking, providing cost-effective tool life management and repeatable results for turning, milling and drilling operations. Suited for machining steel, stainless and heat-resistant alloys, these inserts offer rapid edge renewal and reduced downtime through simple indexing, while versions optimised for internal coolant significantly improve chip control and thermal management in demanding applications. By choosing the right insert grade and geometry you gain improved tool life, predictable wear behaviour and better surface finish thanks to enhanced chip control, with key benefits including wear-resistant carbide, internal coolant compatibility and reliable chip breaking.
CCGW09T308TM-2 WBH10 Wendeplatten - Walter Tools
Take advantage of the combination of CBN cutting performance, precise geometry and high process stability to extend tool life and improve part quality; order directly via Metav Werkzeuge or request tailored advice from our consultants. CCGW09T308TM-2 WBH10 indexable insert — CBN grade for hard turning | Walter Tools The CCGW09T308TM-2 WBH10 is a rhombic 80° indexable insert designed for hard turning and finish operations on hardened steels and similar difficult-to-machine materials. CBN grade WBH10 for hard materials 7° clearance for stable cutting Rhombic 80° geometry for versatile turning Boosted productivity for hard-material machining The insert’s core strength is its CBN composition, specified here as WBH10, which is engineered for high resistance to abrasive wear in hard turning. This translates into longer tool life and fewer index changes during production, reducing downtime and tooling costs. By choosing a CBN solution, operators benefit from consistent cutting performance when machining hardened steels, where conventional carbide grades would wear rapidly. Geometry that enhances stability and surface finish The rhombic 80° shape combined with a 7° clearance angle provides a stable cutting stance and improved chip flow in interrupted and continuous cuts. The moderate 0.8 mm corner radius supports a balance between edge strength and achievable surface quality, meaning fewer rejects and less secondary finishing. The insert’s geometry is therefore suited to both roughing passes where edge security is critical and finishing passes where dimensional accuracy and surface condition matter. Application range and process reliability This insert is optimised for hard and pre-hardened steels, offering reliable performance in serial production and rework tasks. The WBH10 grade is part of the Walter CBN series aimed at machining high-hardness workpieces; its design reduces the frequency of tool changes and helps maintain stable cutting forces. Process planners will appreciate the predictability of tool life when integrating these inserts into production cycles for wear-critical components. Integration and handling on turning systems The CCGW form factor is compatible with a wide range of indexable toolholders used in both conventional lathes and CNC turning centres. The insert’s standardised dimensions and chipbreaker type simplify logistics and stocking, while the robust cutting edge geometry reduces the need for frequent regrinding or special reconditioning. For workshops seeking a low-maintenance cutting solution, this insert offers straightforward handling and consistent repeatability. Contact Metav Werkzeuge for availability and recommendations on Walter Tools CCGW09T308TM-2 WBH10 CBN inserts — email info@metav-werkzeuge.com or call +49 2822 7131930 for application-specific advice and rapid delivery options. Technical data Article number: CCGW09T308TM-2-WBH10-WALTER SKU: CCGW09T308TM-2-WBH10-WALTER Designation: CCGW09T308TM-2 WBH10 Manufacturer: Walter Tools Facts Clearance angle: 7° Corner radius: 0.8 mm Plate size: 09 Plate thickness: T3 Plate form: Rhombus 80° Chipbreaker: 2 Special features Cutting material: CBN (WBH10) Series: Walter CBN / Hartstoff Application: Hard machining, hardened steels (ISO group H) Suitable for pre-hardened steel machining Robust edge for high wear resistance FAQ What materials is this insert intended for? The CCGW09T308TM-2 WBH10 insert is designed primarily for hardened steels and pre-hardened workpieces; the WBH10 CBN grade provides high wear resistance for these applications. How does the 7° clearance affect performance? A 7° clearance angle improves cutting stability and reduces rubbing at the flank, contributing to consistent surface finish and extended tool life when using this indexable insert. Can the insert be used for both roughing and finishing? Yes, the combination of rhombic 80° geometry and a 0.8 mm corner radius allows secure roughing cuts and capable finishing passes when optimised cutting parameters are applied. Is this insert compatible with standard toolholders? The CCGW form factor corresponds to common indexable insert standards and fits compatible turning and boring toolholders, allowing easy integration into existing setups. What are the main benefits of using a CBN grade like WBH10? WBH10 offers superior abrasive wear resistance and process stability for hard machining, reducing tool-change frequency and improving production consistency. Manufacturer: Walter Tools; Manufacturer/Responsible: AB Sandvik Coromant, Mossvägen 10, 811 34 Sandviken, Sweden; support.coromant@sandvik.com Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenzeichen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers.
CCGW09T308TM-2 WBH10C Wendeplatten - Walter Tools
Take advantage of the combination of a CBN-grade cutting material, precise Rhombus 80° geometry, and a 0.8 mm corner radius to ensure consistent performance in hard machining; order the insert directly via Metav Werkzeuge or consult our specialists for process optimisation. CCGW09T308TM-2 WBH10C indexable insert for boring and turning — Walter Tools, CBN grade for hard machining CCGW09T308TM-2 WBH10C is an indexable insert designed for hard and wear-intensive turning and boring tasks, especially on hardened steels. Coated CBN grade WBH10C for hard machining Rhombus 80° shape for versatile tool mounting 7° clearance angle for secure cutting engagement High-performance grade for hardened steels that extends tool life The WBH10C grade is a coated CBN cutting material developed for applications where hardness and abrasion dominate. For components hardened to high levels, the insert provides exceptional wear resistance and stable edge retention, which translates into longer tool life and fewer index changes. This behaviour reduces machine downtime and supports a predictable production rhythm, making the insert particularly suitable for serial hard turning and finishing operations. Geometry engineered for stability and repeatable results With a Rhombus 80° profile and a corner radius of 0.8 mm, the geometry balances strength and edge accessibility. The moderate corner radius helps produce a consistent surface finish while limiting cutting forces that can cause chatter. The 7° clearance prevents rubbing during engagement and improves chip flow, supporting steady cutting conditions even under interrupted cuts. These geometric choices enable the insert to deliver repeatable dimensional accuracy in demanding workflows. Practical benefits in process reliability and economy Designed for wear-intense applications, the insert enables improved process reliability through its CBN-based wear resistance and robust geometry. Fewer insert changes and predictable performance lead to lower overall tooling costs per part. The combination of stable chip formation and high edge security supports higher cutting parameters where applicable, which can shorten cycle times and increase throughput without compromising surface integrity. Suitable applications and material compatibility explained The insert is intended primarily for the machining of hardened steels and prehardened materials where conventional carbide grades struggle. CBN excels at preserving cutting edges against abrasive, high-temperature wear typical in hardened workpieces and certain cast or high-alloy materials. The plate’s designation and series indicate suitability for hard turning, light finishing passes, and operations where dimensional repeatability is a priority. Contact Metav Werkzeuge for tailored cutting data and application advice on Walter Tools CBN inserts to secure optimal performance in hardened-steel operations Technical data Article number: CCGW09T308TM-2-WBH10C-WALTER ISO designation: CCGW09T308TM-2 WBH10C Product type: Bohr-/Aufbohrwendeschneidplatte / Drehwendeschneidplatte Manufacturer: Walter Tools Facts Clearance angle: 7° Corner radius: 0.8 mm Plate size: 09 Plate thickness: T3 Chipbreaker: 2 Tolerance class: G Special features Series: Walter CBN / Hartstoff Grade: WBH10C (coated CBN) Material application: hardened steels (H) Plate form: Rhombus 80° Execution: W FAQ What materials is this insert intended for? This insert, specified as CCGW09T308TM-2 WBH10C by Walter Tools, is intended primarily for hardened steels and prehardened materials where a CBN grade is advantageous. How does the WBH10C grade improve tool life? The WBH10C coated CBN composition offers high abrasion resistance and stable cutting edges, so the insert maintains dimension and surface finish longer under hard machining conditions than typical carbide solutions. What does the 0.8 mm corner radius mean for finish and strength? A 0.8 mm corner radius balances a fine surface finish with structural strength of the cutting edge, reducing the risk of premature edge chipping while producing consistent surface quality. Can the insert be used for interrupted cuts? The insert’s robust Rhombus 80° geometry and coated CBN grade provide good stability for many interrupted-cut scenarios typical in hard turning, though specific cutting data should be validated for the component and machine setup. Is this insert compatible with standard boring and turning toolholders? The Rhombus 80° profile is a common shape for indexable systems; compatibility should be confirmed against the toolholder’s designated insert seat and clamping system using the ISO designation. Manufacturer/Responsible: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen; Germany Protected trademarks and trade names are the property of their respective owners. Brand names and registered marks are mentioned for clarification only. There is no affiliation between our company and the named brands. The offered article is an original, factory-new product of the manufacturer.
CCGW09T308TM-2 WBH20 Wendeplatten - Walter Tools
Combining CBN wear resistance with a 0.8 mm corner radius and a 7° clearance, this insert delivers stable cutting and extended tool life for hard machining operations; order the CCGW09T308TM-2 WBH20 insert directly via Metav Werkzeuge or consult our specialists for application advice. CCGW09T308TM-2 WBH20 indexable insert for hard machining — Walter Tools (CBN grade, Rhombic 80°) The CCGW09T308TM-2 WBH20 is an indexable turning and boring insert engineered for hard machining of hardened steels and similar challenging materials, offering high wear resistance and consistent performance. CBN grade WBH20 for hard machining Rhombic 80° insert form 7° clearance for stable cutting 0.8 mm corner radius for edge strength Optimised CBN grade for durable hard machining The WBH20 grade uses CBN (cubic boron nitride) as the cutting material, which is purposely formulated for high-wear tasks on hardened steels (ISO 513 group H). This results in reliable tool life and lower frequency of insert changes compared with conventional carbide in similar applications. The material's inherent abrasion resistance reduces flank wear, supporting longer uninterrupted production runs and fewer process interruptions, which in turn helps to maintain consistent batch quality and reduce scrap rates. Geometry that improves process stability and surface finish The Rhombic 80° form combined with a 7° clearance angle delivers a robust cutting geometry that resists edge chipping during interrupted cuts and heavy engagement. The 0.8 mm corner radius increases edge strength while still permitting acceptable surface quality on finishing passes. The integrated chipbreaker 2 promotes controlled chip formation in hard turning, reducing the risk of entanglement and safeguarding both the workpiece and the toolholder. Together these features contribute to predictable cycle times and improved first-pass yield. Practical benefits for production planning and machining security Designed as part of the Walter CBN / Hartstoff series, this indexable insert supports a targeted strategy for hard finishing and hard turning operations, offering process security and repeatable results. Specified tolerance class G and the insert's standardised designation make tool management straightforward and reduce setup variability. Use of a CBN-grade insert like this one can lower overall tooling consumption and contribute to more efficient scheduling by extending service intervals and simplifying inventory choices for hardened-steel applications. Contact Metav Werkzeuge for tailored application guidance on the Walter Tools CCGW09T308TM-2 WBH20 insert and to discuss current availability via info@metav-werkzeuge.com or +49 2822 7131930 Technical Data Article number: CCGW09T308TM-2-WBH20-WALTER Designation: CCGW09T308TM-2 WBH20 Manufacturer: Walter Tools Facts Clearance angle: 7° Corner radius: 0.8 mm Insert form: Rhombic 80° Size: 09 Thickness: T3 Chipbreaker: 2 Tolerance class: G Special features CBN grade WBH20, Walter CBN / Hartstoff series Intended for hardened steels (ISO 513 H) Stable edge for hard machining Rhombic 80° geometry for versatile turning and boring FAQ What materials is this insert suitable for? The CCGW09T308TM-2 WBH20 insert is designed primarily for hardened steels (ISO 513 group H) and related hard materials; its CBN cutting grade provides the required wear resistance for these applications. How does the Rhombic 80° shape affect cutting performance? The Rhombic 80° geometry gives a robust cutting edge that tolerates higher radial forces and interrupted cuts, improving process stability and enabling secure edge positioning in a range of turning and boring setups. What advantage does the 0.8 mm corner radius provide? A 0.8 mm corner radius increases edge strength and reduces the likelihood of chipping when machining hard materials, helping to preserve surface integrity and extend the usable life of the insert. Is this insert compatible with standard toolholders for CCGW-style inserts? The insert follows the CCGW designation and is compatible with toolholders designed for that family; for confirmation of holder fitment and clamping specifications refer to tooling documentation or consult Metav Werkzeuge. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Protected trademarks and trade names are the property of their respective owners. Brand names and protected trade names are mentioned for explanatory purposes only and do not indicate any affiliation between our company and the named brands. The offered item is an original, brand-new product of the manufacturer Walter Tools.
CCGW09T308TM-2 WBH20C Wendeplatten - Walter Tools
Benefit from the combination of CBN-grade wear resistance and a robust Rhombic 80° seating that keeps hard-turning operations consistent and productive; the compact geometry and 0.8 mm corner radius support longer tool life and stable cutting. Order the CCGW09T308TM-2 WBH20C directly via Metav Werkzeuge or ask our consultants if needed. CCGW09T308TM-2 WBH20C – Turning insert for hard machining | Walter Tools The CCGW09T308TM-2 WBH20C is a CBN turning insert designed for hard machining of hardened steels, delivering high wear resistance and process stability in demanding finishing and light roughing applications CBN grade for extreme wear resistance Designed for hardened steels (H) Rhombic 80° form for secure seating 0.8 mm corner radius for robust edge Reliable cutting performance for hardened materials The insert is manufactured in a CBN class cutting material that is specifically engineered for machining hardened steels and pre-hardened workpieces. This composition gives a significantly higher wear resistance compared with conventional carbide grades, which translates directly into longer tool life and fewer indexings. In practical terms, the hardened-cutting capability reduces unscheduled tool changes and supports a predictable production rhythm, making the grade particularly suitable where repeatable results and minimal downtime are required. Geometry tuned for stability and surface quality The Rhombic 80° form combined with a 7° clearance and a 0.8 mm corner radius creates a secure seat in the toolholder and a resilient cutting edge under elevated cutting forces. The defined geometry helps to maintain a stable chip flow and reduces vibration during the cut, which improves surface finish and protects the cutting edge. The T3 plate thickness contributes to mechanical rigidity, ensuring that the insert withstands the stresses of hard turning without premature deformation. Application benefits: productivity and process security Because the grade is optimised for hard materials, the insert supports higher material removal rates in applications where abrasive wear would quickly blunt other grades. The design and grade combination promote consistent cutting conditions, which enhances productivity and process security in serial production. For workshop planners and process engineers, this means more predictable tool life, reduced inventory for spare inserts and an easier route to stable cycle times on challenging components. Practical handling and integration into existing tooling The insert’s ISO designation and standard form allow straightforward mounting in compatible turning toolholders, simplifying tool management in mixed fleets. The integrated chipbreaker supports controlled chip formation for common hard-turning conditions, while the stable edge geometry reduces the need for frequent operator adjustments. For customers requiring further clarification on holder compatibility or cutting-data recommendations, technical support and application advice are available to assist with selection and process set-up. For workshops seeking a reliable CBN solution for hard turning, consider the Walter Tools WBH20C insert and contact Metav Werkzeuge for detailed application advice or to request procurement assistance via info@metav-werkzeuge.com or +49 2822 7131930 Technical Data Article number: CCGW09T308TM-2-WBH20C-WALTER Label: Bohr-/Aufbohrwendeschneidplatte / Drehwendeschneidplatte CCGW09T308TM-2 WBH20C Walter Tools Series: Walter CBN / Hartstoff Facts Plate size: 09 Clearance angle: 7° Corner radius: 0.8 mm Plate form: Rhombus 80° Plate thickness: T3 Tolerance class: G Special features Grade: WBH20C (coated CBN) Application: hardened steels (H), hard machining Chipbreaker: 2 Execution: W ISO designation: CCGW09T308TM-2 WBH20C FAQ Is this insert suitable for finishing hardened steels? The CCGW09T308TM-2 WBH20C insert by Walter Tools is specifically designed for hard machining and is well suited to finishing operations on hardened steels, thanks to its CBN composition and stable geometry. Which workpiece materials are recommended for this grade? The WBH20C grade is intended for hardened steels and pre-hardened materials where high abrasion resistance and cutting-edge stability are required. Can the insert be used with standard turning holders? Yes, the ISO form and Rhombic 80° shape of the insert allow use in compatible standard turning toolholders; correct clamping to the holder is important for achieving the quoted process stability. What benefits does the 0.8 mm corner radius deliver? A 0.8 mm corner radius increases edge robustness under heavy cutting loads and contributes to improved surface finish and longer tool life in hard-turning tasks. How does the chipbreaker influence performance on hard materials? The specified chipbreaker supports controlled chip formation in hard-cutting scenarios, helping to avoid long, unstable chips and improving process reliability. Manufacturer/Responsible: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen Protected trademarks and trade names are the property of their respective owners. Brand names and protected trademarks are mentioned for explanatory purposes only. There is no connection between our company and the named brands. The offered article is original, brand-new goods from the manufacturer.
CCGW09T308TM-2 WBH30 Wendeplatten - Walter Tools
Benefit from the wear resistance of the WBH30 CBN grade combined with a stable rhombic 80° geometry and a 0.8 mm corner radius for reliable hard‑turning. Order the insert directly via Metav Werkzeuge or contact our consultants for machining recommendations. CCGW09T308TM-2 WBH30 rhombic 80° CBN insert for hard turning — Walter Tools The CCGW09T308TM-2 WBH30 is a rhombic CBN insert engineered for heavy‑duty turning and boring of hardened steels, delivering stable chip control and long tool life. CBN grade WBH30 for hard materials Rhombic 80° geometry 7° clearance for stable cutting 0.8 mm corner radius for edge strength Durable performance for hardened steel machining The CBN cutting compound of this insert provides exceptional wear resistance, making it ideal for repeated operations on hardened steels. By using a cubic boron nitride grade tailored for hard‑turning, the insert reduces flank wear and maintains a consistent cutting edge over extended cycles. This results in fewer tool changes and more predictable cycle times, which supports higher process reliability in serial production. Geometry designed to withstand heavy cuts The rhombic 80° shape and 0.8 mm corner radius combine to deliver a robust cutting edge that resists chipping under elevated radial and tangential forces. The 7° clearance angle improves chip flow and reduces rubbing on the flank, which helps preserve surface integrity on the workpiece. Together, these geometric choices enable stable machining of hard materials while maintaining a competitive surface finish. Improved productivity through longer tool life Using a CBN insert from the Walter CBN series reduces downtime associated with frequent insert changes and rework. The WBH30 composition is optimised for abrasive, high‑hardness environments; this increases cumulative cutting performance and lowers cost per component. For operations where repeatability and uptime are critical, the combination of coated CBN grade and proven insert geometry provides a measurable productivity advantage. Application guidance and material compatibility This insert is intended for hard machining tasks and is suitable for materials classified under ISO group H, notably hardened steels and pre‑hardened workpieces. The Walter CBN / Hartstoff series is formulated for challenging abrasion and maintains edge stability during intermittent or continuous cuts. When integrating this insert into a process, select appropriate cutting parameters and coolant strategies for CBN tooling to exploit the full benefit of the grade and geometry. For demanding hard‑turning applications, choose the Walter Tools CCGW09T308TM-2 WBH30 and contact Metav Werkzeuge at info@metav-werkzeuge.com or +49 2822 7131930 for tailored cutting data and supply options. Technical data Article number: CCGW09T308TM-2-WBH30-WALTER Designation: CCGW09T308TM-2 WBH30 Brand: Walter Tools Series: Walter CBN / Hartstoff Core data Clearance angle: 7° Corner radius: 0.8 mm Plate form: Rhombus 80° Plate size: 09 Plate thickness: T3 Chipbreaker: 2 Tolerance class: G Features and applications CBN grade WBH30 Execution: W Suitable for hardened steels (ISO H) Suitable for pre‑hardened steel applications Designed for hard turning and abrasive workpiece materials FAQ What materials is this insert best suited for? The insert is intended for hard‑turning and is suitable for materials in ISO group H, particularly hardened steels and pre‑hardened workpieces; the WBH30 CBN grade is optimised for such applications. How does the 0.8 mm corner radius affect cutting? A 0.8 mm corner radius increases edge strength and improves resistance to chipping during heavy cuts, which helps maintain dimensional stability and surface quality over longer tool life. Is the geometry suitable for finishing passes? The rhombic 80° form with a moderate corner radius provides a balance between robust cutting for semi‑finishing and the potential for achieving good surface finish when cutting parameters are adapted. What does the tolerance class G indicate? Tolerance class G specifies the manufacturing tolerance for the insert geometry; this influences fit and repeatability in insert seats and supports consistent performance across batches for the CCGW09T308TM-2 WBH30 insert. Manufacturer: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen; Germany Protected trademarks and brand names are the property of their respective owners. Brand names and trademarks are mentioned for explanation only; no connection between our company and the named brands is implied. The offered item is original, factory‑new merchandise from the manufacturer Walter Tools.
CCGW09T308TM-MW2 WBH10C WBH10C Wendeplatten - Walter Tools
Take advantage of the combination of a CBN grade optimised for hard turning, a stable rhombic geometry and precise chip control for dependable performance in hardened-steel machining; order directly via Metav Werkzeuge or consult our application experts for process parameters and availability CCGW09T308TM-MW2 WBH10C - Rhombic 80° CBN turning insert for hardened steel (Walter Tools) The CCGW09T308TM-MW2 WBH10C is an indexable turning insert designed for hard machining tasks, offering a coated CBN grade for high wear resistance and consistent performance in hardened-steel applications Coated CBN for hard turning Rhombic 80° geometry for versatility 0.8 mm corner radius for edge stability 7° clearance angle for reliable cutting Consistent wear resistance for demanding hard turning The WBH10C grade is a coated CBN cutting material developed to withstand the high temperatures and abrasive conditions typical of hardened-steel machining. As a result, the insert delivers extended tool life and reduced flank wear compared with conventional carbide solutions when applied correctly. CBN (cubic boron nitride) is a superabrasive optimised for permanent hardness and thermal stability; this means the insert maintains cutting-edge geometry under heavy contact stresses, which translates into fewer tool changes and more predictable machining cycles for production environments Geometry and chip control that improve surface quality With a rhombic 80° shape and a 0.8 mm corner radius, this insert combines edge strength with flexible approach angles to achieve consistent surface finish and dimensional stability. The integrated MW2 chipbreaker promotes reliable chip formation during interrupted cuts and finishing passes, reducing the risk of built-up edge and improving swarf evacuation. The modest 7° clearance ensures a controlled cutting engagement and lowers rubbing at the flank, resulting in stable forces and reproducible part quality in serial production Practical advantages for workshop integration and application The insert's T3 plate thickness and tolerance class G offer mechanical robustness and repeatable seating in standard toolholders, supporting process security across shifts. Designed for machining hardened steels and pre-hardened materials, it is suitable for hard turning operations where wear resistance and edge life are critical. Use of a CBN grade minimises thermal deformation of the cutting edge and often enables higher cutting speeds or longer cycles between indexings, improving throughput and cost-efficiency for medium to high-volume production Contact Metav Werkzeuge for tailored application advice and availability of Walter Tools CCGW09T308TM-MW2 WBH10C insert Technical Data Article number: CCGW09T308TM-MW2-WBH10C-WALTER Description: Bohr-/Aufbohrwendeschneidplatte / Drehwendeschneidplatte CCGW09T308TM-MW2 WBH10C Walter Tools Series: Walter CBN / Hartstoff Grade: WBH10C Core specifications Clearance angle: 7° Corner radius: 0.8 mm Insert shape: Rhombus 80° Insert size: 09 Thickness: T3 Tolerance class: G Applications & features Coating / material: Coated CBN Chipbreaker: MW2 Execution: W Suitable for: hardened steels (H) Suitable for: pre-hardened steel Applicable processes: hard turning FAQ What materials is this insert suitable for? This insert is specified for machining hardened steels and is suitable for pre-hardened steel applications, using the WBH10C CBN grade to control wear during hard turning How does a CBN grade compare with carbide for hard machining? Coated CBN, as used in this insert, offers superior thermal and abrasive resistance compared with carbide in hardened materials, resulting in longer edge life and more consistent dimensional output when machining hard workpieces What does the MW2 chipbreaker achieve in practice? The MW2 chipbreaker supports controlled chip formation and improved evacuation, reducing the risk of built-up edge and helping to maintain a consistent surface finish during interrupted or continuous hard-turning operations Which toolholders fit this insert form and size? The rhombic 80° form and size 09 are compatible with standard indexable turning holders designed for CCGW-style inserts; selection of the correct holder and clamping torque ensures the T3 thickness and tolerance class G provide repeatable seating How should cutting data be adjusted for this insert? Cutting parameters depend on the workpiece hardness and machine rigidity; start with manufacturer-recommended speeds for CBN in hardened steels and favour stable feeds and depths of cut to exploit the insert’s wear resistance and process stability Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Protected trademarks and trade names are the property of their respective owners. Mark names and protected designations are used for explanation only. There is no affiliation between our company and the mentioned brands. The offered item is original, brand-new goods supplied by the manufacturer.
CCGW09T308TS-2 WBK20 Wendeplatten - Walter Tools
Take advantage of the combination of longer tool life, stable cutting performance and catalogue-dependent material options to improve productivity in hard-turning applications; order the insert directly via Metav Werkzeuge or consult the team for specification support. CCGW09T308TS-2 WBK20 — Rhombic 80° CBN turning insert by Walter Tools (CBN grade, 7° clearance) CCGW09T308TS-2 WBK20 is a precision CBN turning insert designed for high‑wear and hard‑turning tasks, offering a robust geometry for demanding steel and superalloy machining. CBN grade for hardened materials Rhombic 80° geometry for versatile turning 7° clearance for stable cutting Increased process efficiency for hardened workpieces The combination of CBN cutting material and the WBK20 grade targets high‑wear environments where consistent edge life matters. CBN inserts resist abrasive wear in applications such as hardened steels and certain superalloys, which leads to fewer tool changes and a more predictable production rhythm. The insert’s hard substrate and coated or uncoated variants (catalogue‑dependent) allow for higher cutting speeds and a reduced total cost of machining when compared with conventional carbide solutions in similar tasks. Geometry engineered for stability and surface quality The rhombic 80° form paired with a 0.8 mm corner radius provides a balanced contact area that supports both corrective turning and finishing passes. A 7° clearance angle promotes positive rake behaviour and reduces rubbing on the workpiece, translating into improved surface finish and lower thermal loading of the cutting edge. Where dimensional control is critical, this geometry helps to maintain repeatable cutting conditions and lessens the likelihood of chatter in stable set‑ups. Application guidance and safe selection This insert is supplied in the CCGW09T308TS-2 WBK20 specification and is best considered for operations on hardened steels and materials with high abrasive tendencies; however, final suitability should be verified against the manufacturer’s product matrix. The chipbreaker 2 configuration supports controlled chip formation in interrupted or continuous turning, improving evacuations in automated or semi‑automated machining. For specific cutting data and to match the insert to the machine and workpiece, consult the technical data sheets or request assistance from Metav Werkzeuge. Practical benefits for production planners Adopting a CBN insert such as this one can shorten cycle times through higher permissible cutting speeds and reduce tooling logistics by extending tool life. The T3 thickness and standard plate size 09 make the insert compatible with a wide range of common tool holders, simplifying inventory. In practice, shops report greater process stability and fewer unexpected stoppages when switching to a purpose‑designed CBN grade for hard‑turning tasks. Contact Metav Werkzeuge for tailored advice on integrating the Walter Tools CCGW09T308TS-2 WBK20 into the process, request cutting data or order directly via info@metav-werkzeuge.com or by phone on +49 2822 7131930 Technical Data Article number: CCGW09T308TS-2-WBK20-WALTER Product type: Bohr-/Aufbohrwendeschneidplatte / Drehwendeschneidplatte Series: Walter Schneidstoffsorte - Serie offen Grade: WBK20 Manufacturer: Walter Tools Facts Free angle: 7° Corner radius: 0.8 mm Plate form: Rhombus 80° Plate size: 09 Plate thickness: T3 Chipbreaker: 2 Tolerance class: G Material specification: Catalogue-dependent Special features CBN cutting material for hard and high-wear machining Suited for hardened steels and, depending on matrix, certain cast materials or superalloys Designed for stable cutting and consistent edge life Standard form for versatile turning operations FAQ What materials is this CBN insert suitable for? The CCGW09T308TS-2 WBK20 insert is specified for hardened steels and other high‑wear materials; suitability for cast components or superalloys should be confirmed using the Walter Tools product matrix. How does the rhombic 80° shape affect machining? The rhombic 80° geometry offers flexible approach angles for turning, enabling both roughing and finishing with reliable chip control when combined with the built‑in chipbreaker. What advantages does the WBK20 grade offer? The WBK20 CBN grade provides enhanced wear resistance and dimensional stability in prolonged turning operations, which reduces tool change frequency and improves process predictability. Is the insert compatible with common tool holders? Yes, the size 09 and T3 thickness conform to widely used tool holder standards, facilitating quick integration into existing tool systems. Where to find cutting data for this insert? Cutting parameters and application recommendations are available from the manufacturer’s technical documentation and from Metav Werkzeuge; consult the product matrix before machining. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenzeichen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers.
CCGW120404FS-1 WDN10 WDN10 Wendeplatten - Walter Tools
Take advantage of the combination of long tool life, precise geometry and reliable performance for consistent machining of abrasive non‑ferrous materials; order the insert directly via Metav Werkzeuge or consult the technical advisors if application data is required CCGW120404FS-1 WDN10 — PKD Turning Insert, Rhombic 80° by Walter Tools CCGW120404FS-1 WDN10 is a polycrystalline‑diamond turning insert designed for high‑wear applications on abrasive, non‑ferrous materials PKD grade WDN10 for abrasive non‑ferrous materials Rhombic 80° geometry for flexible turning strategies 7° clearance angle for stable cutting action 0.4 mm corner radius for improved surface finish High wear resistance for abrasive non‑ferrous machining The polycrystalline diamond (PKD) composition of this insert delivers outstanding wear resistance when machining abrasive, non‑ferrous materials. The PKD grade WDN10 is engineered to withstand high abrasive loads, which translates into longer intervals between tool changes and more predictable tool life. For production environments where consistent component quality and reduced downtime are priorities, the insert’s hard compound reduces flank and crater wear, helping to maintain dimensional accuracy over extended runs. Suitability for specific alloys should be verified against the product matrix to ensure optimal results. Geometry engineered for reliable finishes and process stability A combination of the rhombic 80° geometry and the 0.4 mm corner radius supports both turning versatility and fine surface quality. The 7° clearance angle provides positive cutting engagement while limiting rubbing on the flank, which helps to preserve the cutting edge and reduce built‑up edge formation. The integrated chipbreaker 1 is tailored for controlled chip formation in non‑ferrous, abrasive conditions, promoting steady material evacuation and stable cutting forces. These geometric features together support predictable machining and repeatable part quality in CNC turning operations. Practical integration and economic benefits in production Designed as a straightforward replacement insert for compatible toolholders, the insert belongs to the Walter Schneidstoffsorte series and is supplied under the designation CCGW120404FS‑1 WDN10. The PKD grade reduces tool consumption for challenging materials, which can improve cost per part in high‑volume applications. In mixed‑material production or in workpieces containing abrasive inclusions, the insert’s wear properties contribute to fewer unexpected tool failures and reduced scrap rates, supporting continuous production and operational efficiency. For specific process parameters and to confirm compatibility with the chosen workpiece material, technical advice is available on request Choose the Walter Tools PKD insert for robust performance in abrasive non‑ferrous turning and contact Metav Werkzeuge for application guidance and availability Technical data Article number: CCGW120404FS-1-WDN10-WALTER Designation: CCGW120404FS-1 WDN10 Manufacturer: Walter Tools Product type: Turning/cutting insert Series: Walter Schneidstoffsorte - Serie offen Grade: WDN10 Style: W Facts Geometry: Rhombic 80° Clearance angle: 7° Corner radius: 0.4 mm Plate size: 12 Plate thickness code: 04 Chipbreaker: 1 Tolerance class: G Special features PKD (polycrystalline diamond) cutting material Suitable for abrasive, non‑ferrous materials (check matrix) Designation without grade: CCGW120404FS-1 WDN10 is a PKD grade optimised for wear resistance FAQ What materials is this insert optimised for? The CCGW120404FS‑1 WDN10 insert is optimised for abrasive, non‑ferrous materials; the PKD grade WDN10 offers high wear resistance for such applications. Can the insert be used for finishing and roughing operations? Yes, the rhombic 80° geometry combined with a 0.4 mm corner radius enables both controlled finishing and robust roughing in suitable non‑ferrous workpieces when parameters are adapted. How does the 7° clearance angle affect cutting performance? The 7° clearance angle reduces flank contact and helps maintain a stable cutting edge, which supports consistent surface quality and extended tool life for the Walter Tools insert. Is the chip formation controlled for automated machining? The integrated chipbreaker 1 is designed to produce predictable chips in abrasive non‑ferrous machining, aiding evacuation and process stability during CNC turning. How should suitability for a specific alloy be verified? Suitability for a particular alloy should be checked against the product matrix and process data; the CCGW120404FS‑1 WDN10 benefits from PKD properties but requires parameter adaptation for best results. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Protected trademarks and trade names are the property of their respective owners. Brand names and protected product names are used for explanatory purposes only. There is no connection between our company and the named brands. The offered item is original, factory‑new goods of the manufacturer.
CCGW120408FS-1 WDN10 WDN10 Wendeplatten - Walter Tools
High wear resistance and precise geometry combine to deliver efficient, repeatable machining of abrasive non‑ferrous materials; the polycrystalline diamond grade WDN10 paired with a 0.8 mm corner radius and 7° clearance supports long tool life and stable chip control. Order the CCGW120408FS-1 WDN10 indexable insert directly via Metav Werkzeuge or ask the consultants for application advice. CCGW120408FS-1 WDN10 indexable insert for abrasive non‑ferrous machining | Walter Tools The CCGW120408FS-1 WDN10 is an indexable turning and boring insert engineered for productive machining of abrasive non‑ferrous metals and other abrasive, non‑ferrous materials. PKD grade WDN10 for abrasive non‑ferrous materials Rhombus 80° geometry for versatile turning 0.8 mm corner radius for consistent edge strength 7° clearance angle for reliable chip control Improved productivity through a wear‑resistant cutting grade The combination of polycrystalline diamond (PKD) in grade WDN10 and robust geometry delivers measurable gains in tool life when tackling abrasive non‑ferrous materials. PKD is especially resistant to abrasive wear, which translates into fewer index changes and longer uninterrupted run times on production lathes and turning centres. The design prioritises cutting stability and consistent surface finish, so shops processing abrasive aluminium alloys, graphite or other non‑ferrous substrates can expect reduced rework and improved throughput. These technical advantages create a clear cost‑benefit for high‑volume and precision applications. Geometry and edge design that support consistent results The Rhombus 80° form, combined with a 0.8 mm corner radius and 7° clearance, offers a balance between strength and accessibility to typical profiles. The modest corner radius helps maintain a durable cutting edge while supporting repeatable dimensional control on facing and light profiling operations. Chipbreaker 1 is tuned to promote predictable chip formation with the intended material class, reducing the risk of chip entanglement and improving coolant access. Together, these features enable reliable machining with fewer interruptions and consistent part quality across batches. Application guidance and integration into production As an indexable insert optimised for abrasive non‑ferrous work, the insert suits a range of CNC turning and boring setups where PKD grades are indicated. The CCGW form and the insert’s thickness provide stability in standard toolholders designed for rhombic inserts. Selection should follow the machine, workpiece and process matrix for cutting speeds, feeds and coolant strategy; the PKD grade is not intended for ferrous materials. For shops seeking to standardise inserts across multiple cells, this grade offers a predictable wear pattern and good repeatability in series production. Contact Metav Werkzeuge for application recommendations and to secure CCGW120408FS-1 WDN10 from Walter Tools; call +49 2822 7131930 or email info@metav-werkzeuge.com Technical data Article number: CCGW120408FS-1-WDN10-WALTER ISO designation: CCGW120408FS-1 WDN10 Product type: Bohr-/Aufbohrwendeschneidplatte / Drehwendeschneidplatte Core specifications Inscribed circle: 12 mm Thickness: 4 mm Corner radius: 0.8 mm Clearance angle: 7° Geometry: Rhombus 80° Chipbreaker: 1 Materials & features Grade: polycrystalline diamond (PKD), WDN10 Series: Walter Schneidstoffsorte - Serie offen Tolerance class: G Execution: W Material information: catalogue‑dependent FAQ Is this insert suitable for aluminium and other non‑ferrous alloys? Yes. The CCGW120408FS-1 WDN10 features a PKD grade formulated for abrasive non‑ferrous metals and related materials, offering enhanced wear resistance during long runs. Can the insert be used on steel or cast iron? No. The PKD composition of this insert is intended for non‑ferrous and abrasive non‑ferrous substrates; steel and cast iron are not suitable for this grade. Which toolholders are compatible with this insert geometry? Standard holders that accept CCGW‑form rhombic inserts and support a Rhombus 80° mounting will be compatible; ensure the holder matches the 12 mm inscribed circle and thickness specifications. How does the 0.8 mm corner radius affect finish and strength? The 0.8 mm radius balances edge strength and surface finish, improving resistance to chipping while maintaining good dimensional control on common turning operations. What advantages does the WDN10 grade provide in production? WDN10 delivers long life on abrasive non‑ferrous materials, consistent edge performance and predictable wear, supporting higher uptime and lower insert consumption in repetitive machining tasks. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Walter Tools is part of an established group of precision tool manufacturers and focuses on robust cutting solutions. Markennamen und geschützte Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenzeichen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers.
CCGX 060202 -AL 1205 Indexable Insert - Sandvik
Are you unsure whether the tool is suitable for your application? Or do you need further technical information?No problem - feel free to contact us! ☎️ Phone: +49 2822 7131930, ✔️ WhatsApp: +49 170 2837271, 📧 eMail: info@metav-werkzeuge.com Technical data for CCGX 060202 indexable inserts from Sandvik Brand: Sandvik Manufacturer Order Number: CCGX060202-AL1205-SANDVIK Facts for the tool: ISO-Code: CCGX060202 Clearance Angle: 7° Thickness: 2,38mm Radius: 0.2 Features Material: cemented carbide Grade: 1205 Chip Breaker: -AL special Hole Style: special Form: rhombic Chip Breaker: special Manufacturer: Registered brand names and trademarks are the property of their respective owners. The naming of brand names and protected trademarks is for descriptive purposes only. The brands mentioned are not in any contractual relationship with our company. This is a brand new original product of the leading brand Sandvik. 40START indexable-inserts-CCGX-060202-1205-Sandvik 40END
CCGX 060202 AL 1105 Indexable Insert - Sandvik
Unsure whether the tool is the right one? Or are you missing technical data?Just get in touch with us! 📧 eMail: info@metav-werkzeuge.com, ☎️ Phone: +49 2822 7131930, ✔️ WhatsApp: +49 170 2837271 Information on technical features CCGX 060202 inserts from Sandvik Brand: Sandvik Manufacturer Order Number: CCGX060202AL1105-SANDVIK Figures for the tool: ISO-Code: CCGX060202 Clearance Angle: 7° Thickness: 2,38mm Radius: 0.2 Special features Material: cemented carbide Grade: 1105 Chip Breaker: AL special Hole Style: special Form: rhombic Chip Breaker: special Manufacturer: Registered trademarks and trade names are the property of their respective owners. The designation of brand names and trademarks is for explanatory purposes only. The brands mentioned are not in any contractual relationship with our company. The article presented is a brand-new original product of the Sandvik brand. 40START indexable-inserts-CCGX-060202-1105-Sandvik 40END
CCGX 060202 Indexable Insert for Aluminium - MetavCUT
Areyou not sure whether this tool fulfils your requirements? Or do you need additional technical data?No problem - we will be happy to help you 📧 eMail: info@metav-werkzeuge.com, ☎️ Phone: +49 2822 7131930, ✔️ WhatsApp: +49 170 2837271 Design details for CCGX 060202 indexable inserts from MetavCUT Brand: MetavCUT Manufacturer Order Number: CCGX060202-Aluminium Dataand Figures: ISO-Code: CCGX060202 Clearance Angle: 7° Angle: 80° Thickness: 2,38mm Radius: 0.2 Special features Material: cemented carbide Usage for: Aluminium special Hole Style: special Form: rhombic Chip Breaker: special Manufacturer: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; www.metav-shop.de; info@metav-werkzeuge.com 40START indexable-inserts-CCGX-060202-Aluminium-MetavCUT 40END
CCGX 060202 Indexable Insert for Stahl - MetavCUT
Unsure whether the tool is the right one? Or are you missing technical data?Just get in touch with us! 📧 eMail: info@metav-werkzeuge.com ☎️ Phone: +49 2822 7131930 ✔️ WhatsApp: +49 170 2837271 Specifications CCGX 060202 indexable inserts from MetavCUT Brand: MetavCUT Manufacturer Order Number: CCGX060202-Steel Figures for the tool: ISO-Code: CCGX060202 Clearance Angle: 7° Angle: 80° Thickness: 2,38mm Radius: 0.2 Special features Material: cemented carbide special Hole Style: special Form: rhombic Chip Breaker: special Manufacturer: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; www.metav-shop.de; info@metav-werkzeuge.com 40START indexable-inserts-CCGX-060202-Stahl-MetavCUT 40END
CCGX 060202 Indexable Insert for Stainless Steel - MetavCUT
Areyou not sure whether this tool fulfils your requirements? Or do you need additional technical data?No problem - we will be happy to help you 📧 eMail: info@metav-werkzeuge.com, ☎️ Phone: +49 2822 7131930, ✔️ WhatsApp: +49 170 2837271 Product features for indexable inserts CCGX 060202 from MetavCUT Brand: MetavCUT Manufacturer Order Number: CCGX060202-Stainless Facts / Figures: ISO-Code: CCGX060202 Clearance Angle: 7° Angle: 80° Thickness: 2,38mm Radius: 0.2 Special features Material: cemented carbide Usage for: Stainless steel special Hole Style: special Form: rhombic Chip Breaker: special Manufacturer: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; www.metav-shop.de; info@metav-werkzeuge.com 40START indexable-inserts-CCGX-060202-Stainless Steel-MetavCUT 40END
CCGX 060202 LH10 Indexable Insert - Sandvik
Are you unsure whether the tool is suitable for your application? Or are you still missing technical data?No problem, just contact us!!! 📧 eMail: info@metav-werkzeuge.com ✔️ WhatsApp: +49 170 2837271 ☎️ Phone: +49 2822 7131930 Product details for indexable inserts CCGX 060202 from Sandvik Brand: Sandvik Manufacturer Order Number: CCGX060202ALH10-SANDVIK Facts and Figures: ISO-Code: CCGX060202 Clearance Angle: 7° Thickness: 2,38mm Radius: 0.2 Special features Material: cemented carbide Grade: LH10 special Hole Style: special Form: rhombic Chip Breaker: special Manufacturer: Registered trademarks and trade names are the property of their respective owners. The naming of brand names and protected trademarks is for descriptive purposes only. Mention of the brands does not imply any relationship to our company. The sales offer includes high-quality, new branded articles from the manufacturer Sandvik. 40START indexable-inserts-CCGX-060202-LH10-Sandvik 40END
CCGX 060204 -AL 1205 Indexable Insert - Sandvik
Not sure whether this tool is suitable for your application? Or are you still missing important technical details? No problem!Contact us - we will be happy to advise you. 📧 eMail: info@metav-werkzeuge.com, ☎️ Phone: +49 2822 7131930, ✔️ WhatsApp: +49 170 2837271 Specifications CCGX 060204 indexable inserts from Sandvik Brand: Sandvik Manufacturer Order Number: CCGX060204-AL1205-SANDVIK Dataand Figures: ISO-Code: CCGX060204 Clearance Angle: 7° Thickness: 2,38mm Radius: 0.4 Special features Material: cemented carbide Grade: 1205 Chip Breaker: -AL special Hole Style: special Form: rhombic Chip Breaker: special Manufacturer: Brand names and protected trademarks are the property of their respective owners. The mention of protected brand names and trademarks is for illustrative purposes only. There is no connection whatsoever between our company and the brands mentioned. The article presented is a brand-new original product of the Sandvik brand. 40START indexable-inserts-CCGX-060204-1205-Sandvik 40END
CCGX 060204 AL 1105 Indexable Insert - Sandvik
You couldn't find the right insert? Let us help you!► Send us a photo of your insert by e-mail.► Send us a drawing by email► Send us your sample insert or drawing by post. Product details CCGX 060204 indexable inserts from Sandvik Brand: Sandvik Manufacturer Order Number: CCGX060204AL1105-SANDVIK Facts for the tool: ISO-Code: CCGX060204 Clearance Angle: 7° Thickness: 2,38mm Radius: 0.4 Features Material: cemented carbide Grade: 1105 Chip Breaker: AL special Hole Style: special Form: rhombic Chip Breaker: special Manufacturer: Brand names and registered trademarks are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no connection whatsoever between our company and the brands mentioned. The article presented is a brand-new original product of the Sandvik brand. 40START indexable-inserts-CCGX-060204-1105-Sandvik 40END
CCGX 060204 Indexable Insert for Aluminium - MetavCUT
Areyou not sure whether this tool fulfils your requirements? Or do you need additional technical data?No problem - we will be happy to help you ✔️ WhatsApp: +49 170 2837271, ☎️ Phone: +49 2822 7131930, 📧 eMail: info@metav-werkzeuge.com Product specifications for indexable inserts CCGX 060204 from MetavCUT Brand: MetavCUT Manufacturer Order Number: CCGX060204-Aluminium Data & Figures: ISO-Code: CCGX060204 Clearance Angle: 7° Angle: 80° Thickness: 2,38mm Radius: 0.4 Special features Material: cemented carbide Usage for: Aluminium special Hole Style: special Form: rhombic Chip Breaker: special Manufacturer: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; www.metav-shop.de; info@metav-werkzeuge.com 40START indexable-inserts-CCGX-060204-Aluminium-MetavCUT 40END
CCGX 060204 Indexable Insert for Stahl - MetavCUT
Unsure whether the tool is the right one? Or are you missing technical data?Just get in touch with us! 📧 eMail: info@metav-werkzeuge.com ☎️ Phone: +49 2822 7131930 ✔️ WhatsApp: +49 170 2837271 Information on technical features insert CCGX 060204 from MetavCUT Brand: MetavCUT Manufacturer Order Number: CCGX060204-Steel Facts and Figures: ISO-Code: CCGX060204 Clearance Angle: 7° Angle: 80° Thickness: 2,38mm Radius: 0.4 Features Material: cemented carbide Usage for: Steel special Hole Style: special Form: rhombic Chip Breaker: special Manufacturer: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; www.metav-shop.de; info@metav-werkzeuge.com 40START indexable-inserts-CCGX-060204-Stahl-MetavCUT 40END
CCGX 060204 Indexable Insert for Stainless Steel - MetavCUT
Are you unsure whether the tool is suitable for your application? Or are you still missing technical data?No problem, just contact us!!! ✔️ WhatsApp: +49 170 2837271 📧 eMail: info@metav-werkzeuge.com ☎️ Phone: +49 2822 7131930 Specifications indexable inserts CCGX 060204 from MetavCUT Brand: MetavCUT Manufacturer Order Number: CCGX060204-Stainless Facts for the tool: ISO-Code: CCGX060204 Clearance Angle: 7° Angle: 80° Thickness: 2,38mm Radius: 0.4 Features Material: cemented carbide Usage for: Stainless steel special Hole Style: special Form: rhombic Chip Breaker: special Manufacturer: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; www.metav-shop.de; info@metav-werkzeuge.com 40START indexable-inserts-CCGX-060204-Stainless Steel-MetavCUT 40END
CCGX 060204 LH10 Indexable Insert - Sandvik
Are you unsure whether the tool is suitable for your application? Or are you still missing technical data?No problem, just contact us!!! 📧 eMail: info@metav-werkzeuge.com, ☎️ Phone: +49 2822 7131930, ✔️ WhatsApp: +49 170 2837271 Information on technical features for CCGX 060204 indexable inserts from Sandvik Brand: Sandvik Manufacturer Order Number: CCGX060204ALH10-SANDVIK Facts and Figures: ISO-Code: CCGX060204 Clearance Angle: 7° Thickness: 2,38mm Radius: 0.4 Features Material: cemented carbide Grade: LH10 special Hole Style: special Form: rhombic Chip Breaker: special Manufacturer: Brand names and registered trademarks are the property of their respective owners. The mention of brands and registered trademarks is for descriptive purposes only. The brands mentioned are not in any contractual relationship with our company. The items offered are original, brand-new goods of the Sandvik brand. 40START indexable-inserts-CCGX-060204-LH10-Sandvik 40END
CCGX 060208 Indexable Insert for Aluminium - MetavCUT
Are you unsure whether the tool is suitable for your application? Or are you still missing technical data?No problem, just contact us!!! ✔️ WhatsApp: +49 170 2837271, 📧 eMail: info@metav-werkzeuge.com, ☎️ Phone: +49 2822 7131930 Information on technical features for indexable inserts CCGX 060208 from MetavCUT Brand: MetavCUT Manufacturer Order Number: CCGX060208-Aluminium Facts for the tool: ISO-Code: CCGX060208 Clearance Angle: 7° Angle: 80° Thickness: 2,38mm Radius: 0.8 Features Material: cemented carbide Usage for: Aluminium special Hole Style: special Form: rhombic Chip Breaker: special Manufacturer: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; www.metav-shop.de; info@metav-werkzeuge.com 40START indexable-inserts-CCGX-060208-Aluminium-MetavCUT 40END
CCGX 060208 Indexable Insert for Stahl - MetavCUT
You couldn't find the right insert? Let us help you!► Send us a photo of your insert directly by email► Send us your drawing directly by e-mail.► Send us a sample insert or drawing by post Product specifications for indexable inserts CCGX 060208 from MetavCUT Brand: MetavCUT Manufacturer Order Number: CCGX060208-Steel Facts and Figures: ISO-Code: CCGX060208 Clearance Angle: 7° Angle: 80° Thickness: 2,38mm Radius: 0.8 Special features Material: cemented carbide Usage for: Steel special Hole Style: special Form: rhombic Chip Breaker: special Manufacturer: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; www.metav-shop.de; info@metav-werkzeuge.com 40START indexable-inserts-CCGX-060208-Stahl-MetavCUT 40END
CCGX 060208 Indexable Insert for Stainless Steel - MetavCUT
Are you unsure whether the tool is suitable for your application? Or do you need further technical information?No problem - feel free to contact us! 📧 eMail: info@metav-werkzeuge.com ☎️ Phone: +49 2822 7131930 ✔️ WhatsApp: +49 170 2837271 Features for indexable inserts CCGX 060208 from MetavCUT Brand: MetavCUT Manufacturer Order Number: CCGX060208-Stainless Data/ Figures: ISO-Code: CCGX060208 Clearance Angle: 7° Angle: 80° Thickness: 2,38mm Radius: 0.8 Features Material: cemented carbide Usage for: Stainless steel special Hole Style: special Form: rhombic Chip Breaker: special Manufacturer: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; www.metav-shop.de; info@metav-werkzeuge.com 40START indexable-inserts-CCGX-060208-Stainless Steel-MetavCUT 40END
Why indexable inserts are indispensable in modern machining
Indexable inserts, also known as cutting inserts or indexable cutting inserts, are standardised, replaceable cutting elements that mount on tool holders such as turning bits, milling cutters or drills. Made from wear-resistant materials like carbide, cermet, ceramic or other superhard grades, they carry the actual cutting edge and allow a worn corner to be rotated or flipped instead of replacing or regrinding the entire tool body.
How these inserts work and when to choose them
In everyday workshop and production settings, indexable inserts perform the direct material removal on the workpiece. Standard inserts for tool systems without internal coolant typically feature closed faces or a single central fixing hole, with heat evacuation handled by external machine nozzles. Inserts designed for systems with internal coolant are engineered to support coolant flow: they include calculated chipbreaker geometries that guide an internal coolant jet under the chip or, in specialised designs, contain sintered microchannels to direct coolant right to the cutting edge. Such coolant-compatible inserts are essential for machining heat-resistant alloys, heavy cutting operations and deep internal machining, where thermal load and chip control are critical.
Tangible benefits for production and workshop efficiency
Choosing the right indexable inserts delivers measurable operational advantages:
- Reduced downtime: faster changeover because a worn insert is simply indexed rather than the whole tool being replaced.
- Extended cutting-edge life: targeted coolant application and optimised chipbreaker design lower thermal stress and improve tool life.
- Consistent part quality: predictable cutting-edge geometry from standardised inserts maintains tolerances across batches.
- Versatility: availability in carbide, cermet, ceramic and superhard grades permits selection according to workpiece material and cutting conditions.
- Lower tooling costs over time: fewer full-tool replacements and less regrinding required.
Metav as a dependable source for inserts and tooling systems
Metav combines decades of precision expertise with a wide-ranging supply chain, positioning itself as a practical partner for industry, craft and trade. From Emmerich on the Rhine, Metav operates as a quality filter for the European market, offering more than 250,000 products and serving over 48,000 customers. For procurement teams aiming to reduce supplier count while retaining technical reliability, Metav’s assortment of indexable inserts and compatible tool holders provides a central, trustworthy solution.
Quick summary
Indexable inserts (cutting inserts or indexable cutting inserts) enable economical, repeatable material removal by allowing worn cutting edges to be indexed or replaced quickly; coolant-adapted designs further reduce thermal load and enhance chip control for demanding applications.
FAQ
What materials are indexable inserts available in?
Indexable inserts are available in wear-resistant grades such as carbide, cermet, ceramic and other superhard materials, selected according to the workpiece material and cutting conditions.
When should I choose inserts with internal coolant support?
Choose inserts designed for internal coolant when machining heat-resistant alloys, performing heavy cuts or working in deep internal features, because the coolant reduces thermal load at the cutting edge and actively improves chip breakage.
How do chipbreaker geometries affect performance?
Chipbreaker geometries on indexable inserts guide the chip flow and, when matched to an internal coolant jet, direct the coolant under the chip to control temperature and facilitate reliable chip formation, which extends edge life and stabilises machining.
Can standard inserts be used with external coolant only?
Yes; standard inserts for tool systems without internal coolant typically have closed faces or a central fixing hole and rely on external machine nozzles for heat evacuation, which is sufficient for many routine, accessible cuts.
Why source inserts through Metav?
Metav supplies a broad range of indexable inserts and tooling, backed by decades of expertise and a comprehensive European stock, making it a practical choice for consistent quality and dependable delivery.
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com