Durable indexable inserts for efficient metalcutting
Indexable inserts are hardened cutting elements designed to deliver consistent material removal in metalworking, providing cost-effective tool life management and repeatable results for turning, milling and drilling operations. Suited for machining steel, stainless and heat-resistant alloys, these inserts offer rapid edge renewal and reduced downtime through simple indexing, while versions optimised for internal coolant significantly improve chip control and thermal management in demanding applications. By choosing the right insert grade and geometry you gain improved tool life, predictable wear behaviour and better surface finish thanks to enhanced chip control, with key benefits including wear-resistant carbide, internal coolant compatibility and reliable chip breaking.
ADHT10T3PER-G88 WXN15 T Wendeplatten - Walter Tools
High‑precision results for non‑ferrous machining are achieved by combining the WXN15 uncoated carbide grade with the G88 chipbreaker and a parallelogram 85° geometry, delivering clean edges and stable chip formation. Order the ADHT10T3PER‑G88 WXN15 directly via Metav Werkzeuge or ask our consultants if needed. ADHT10T3PER-G88 WXN15 – Indexable milling insert, sharp uncoated carbide for non‑ferrous metals (Walter Tools) The ADHT10T3PER‑G88 WXN15 is a parallelogram 85° indexable insert with a 15° relief, engineered for high‑performance machining of non‑ferrous metals such as aluminium and brass Sharp uncoated carbide WXN15 for NE‑metals Parallelogram 85° geometry for robust engagement 15° relief angle for precise, burr‑free cuts G88 chipbreaker for consistent chip control Productivity gains for non‑ferrous machining The combination of a sharp, uncoated carbide grade and a geometry tuned for non‑ferrous materials yields measurable productivity benefits. The WXN15 grade is designed for clean shearing of aluminium, copper and brass, reducing built‑up edge and minimising secondary finishing. This insert’s sharp cutting edge and uncoated surface help maintain low cutting forces at typical speeds for non‑ferrous alloys, which in turn supports longer tool life in many standard applications while keeping process costs predictable. Geometry and chip control for consistent surfaces A parallelogram 85° form and 15° relief provide a stable cutting stance with reliable engagement at the toolholder seat; the geometry reduces chatter and improves surface finish on long or thin components. The integrated chipbreaker G88 promotes controlled chip formation and evacuation, which is crucial when machining sticky or soft alloys. The insert’s T3 thickness ensures secure clamping and resistance to edge deformation, so fewer interruptions for regrinding or part rework are required—supporting smoother production cycles. Grade selection and workshop advantages Built within the Walter N‑grade system, this insert suits sharp, uncoated cutting strategies where adhesion‑free performance is required. The design and tolerance class H deliver repeatable seating, enabling quick index changes and minimal set‑up deviation. For workshops processing a range of non‑ferrous components, the ADHT10T3PER‑G88 WXN15 offers a pragmatic balance of surface quality and chip control, simplifying tooling variants while maintaining consistent results across batches. For proven chip control in non‑ferrous machining, contact Metav Werkzeuge at info@metav-werkzeuge.com or +49 2822 7131930 to discuss the ADHT10T3PER‑G88 WXN15 insert and suitable holder options. Technical Data Article number: ADHT10T3PER-G88-WXN15-WALTER Designation: ADHT10T3PER‑G88 WXN15 Product type: Indexable milling insert Manufacturer: Walter Tools Facts Size: 10 Thickness: T3 Free angle: 15° Plate form angle: Parallelogram 85° Tolerance class: H Special features Grade: uncoated carbide WXN15 Chipbreaker: G88 Series: Walter N‑grade system Suitable for: Non‑ferrous metals (aluminium, copper, brass) Application: sharp / uncoated cutting FAQ What materials is this insert best suited for? The ADHT10T3PER‑G88 WXN15 insert is optimised for non‑ferrous metals such as aluminium, copper and brass, where a sharp, uncoated cutting edge reduces material adherence. How does the G88 chipbreaker improve machining? The G88 chipbreaker promotes short, controllable chips and prevents long stringing chips, improving process stability and reducing the risk of surface damage during milling. Which cutter body and holder geometry pair well with this insert? A rigid milling cutter with a matching parallelogram 85° seat and secure clamping is recommended; the 15° relief and T3 thickness ensure proper support and repeatable indexability. Is the WXN15 grade coated or uncoated? WXN15 is an uncoated carbide grade designed for sharp cutting applications in non‑ferrous materials, prioritising low adhesion and crisp shearing action. What does tolerance class H mean for repeatability? Tolerance class H denotes tight manufacturing tolerances that support accurate seating and consistent tool runout, which helps reduce set‑up times and improves reproducibility between insert changes. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Walter AG (brand appearance: Walter Tools) with headquarters in Tübingen is among the world’s leading manufacturers of precision metal‑cutting tools and is part of the Sandvik group. Protected trademarks and trade names are the property of their respective owners. Brand names and protected marks are used here for explanatory purposes only. There is no connection between our company and the named brands. The offered item is an original, factory‑new product from the manufacturer.
ADHT120416L-G88 WXN15 T Wendeplatten - Walter Tools
Benefit from a tool that combines sharp, uncoated carbide performance for non-ferrous metals with a parallelogram 85° geometry and a 15° free angle to reduce cutting forces and improve surface quality. Order the inserts directly via Metav Werkzeuge or contact the consultants for application-specific advice. ADHT120416L-G88 WXN15 milling indexable insert – Parallelogram 85°, 15° free angle (Walter Tools) The ADHT120416L-G88 WXN15 is a precision milling indexable insert engineered for sharp, uncoated cutting in non‑ferrous metals within the Walter N‑series. Walter N‑series uncoated carbide WXN15 Optimised for non‑ferrous metals like aluminium Parallelogram 85° geometry, 15° free angle High‑efficiency cutting for non‑ferrous metals The insert is built on an uncoated carbide substrate optimised for non‑ferrous metals (ISO group N), providing a very sharp cutting edge that minimises material adhesion and reduces built‑up edge. The WXN15 grade is designed specifically for abrasive‑sensitive workpieces such as aluminium, copper and brass, combining edge sharpness with sufficient toughness to withstand interrupted cuts. The chipbreaker G88 improves chip formation and evacuation, which helps maintain stable process behaviour and reduces the risk of surface blemishes on delicate workpieces. This results in predictable machining and fewer rework cycles. Geometry that improves control and surface finish The parallelogram 85° shape together with a 15° free angle lowers effective cutting forces and offers a positive engagement for slotting and face milling operations. The corner radius of 1.6 mm balances edge strength and finish: small enough for fine finishes, yet large enough to resist premature chipping under moderate feed rates. These geometric choices support higher feed per tooth and better productivity while preserving component quality, making the insert suitable for demanding production runs and one‑off precision parts alike. Operational benefits for workshop efficiency Thanks to the combination of uncoated carbide and a dedicated chipbreaker, this insert delivers consistent chip control and low tendency to smear on soft metals, enabling longer tool‑change intervals and reduced machine downtime. Secure clamping from the parallelogram form ensures repeatable seat orientation, which simplifies indexable insert changes and cuts set‑up time. Where reduced post‑machining is crucial, the result is fewer finishing passes and lower total cycle time, increasing overall throughput on small and medium series production. Practical handling and application notes The insert suits operations where sharp, uncoated edges are preferable for thermal‑sensitive workpieces. For best results, combine with appropriate cutting fluids or high‑pressure air for aluminium applications to further limit adhesion. The designation in the Walter N‑series signals compatibility with established Walter toolholders; selection of the correct seat and clamp is essential for repeatable performance. The SKU and series labelling ensure traceability and straightforward ordering for production planning. Contact Metav Werkzeuge for application support or ordering of Walter Tools ADHT120416L-G88 WXN15 inserts; email info@metav-werkzeuge.com or call +49 2822 7131930 for tailored advice and availability Product details Article number: ADHT120416L-G88-WXN15-WALTER ISO designation: ADHT120416L-G88 WXN15 Series: Walter N‑series Grade: WXN15 Manufacturer: Walter Tools Dimensions & numbers Free angle: 15° Corner radius: 1.6 mm Insert size: 12 Thickness code: 04 Tolerance class: H Materials & special features Shape: Parallelogram 85° Chipbreaker: G88 Execution: T Substrate: uncoated carbide (for non‑ferrous metals) FAQ What materials is this insert best suited for? The ADHT120416L-G88 WXN15 insert from Walter Tools is optimised for non‑ferrous metals (ISO group N), such as aluminium, copper and brass, offering sharp cutting edges and good chip evacuation. How does the G88 chipbreaker help in production? The G88 chipbreaker promotes consistent chip formation and evacuation for the WXN15 grade, reducing the risk of material adhesion and improving surface finish during continuous milling operations. Can this insert be used for interrupted cuts? Yes, the combination of the parallelogram 85° geometry and the WXN15 substrate provides sufficient toughness for many interrupted cut scenarios in non‑ferrous applications; however, machining parameters should be corrected to the specific workpiece and holder. Is the insert coated? No, the WXN15 grade is an uncoated carbide developed for sharp, low‑adhesion performance on soft metals. Which aspects help reduce setup and downtime? The positive parallelogram form ensures repeatable seating and secure clamping, which simplifies indexing and reduces tool‑change time for production environments. Walter Tools: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Protected trademarks and trade names remain the property of their respective owners. Brand names and protected product designations are mentioned for explanatory purposes only and do not imply any affiliation between our company and the trademark holders. The offered item is original, factory‑new merchandise from the manufacturer.
ADHT120416R-G88 WXN15 Wendeplatten - Walter Tools
Take advantage of a sharp, uncoated grade paired with an optimised G88 chipbreaker to ensure clean, predictable machining of non‑ferrous materials; the design combines reliable chip control with a stable cutting edge for efficient production. Order the ADHT120416R-G88 WXN15 directly via Metav Werkzeuge or ask our consultants if needed. ADHT120416R-G88 WXN15 milling insert — Parallelogram 85°, 15° relief, Walter Tools The ADHT120416R-G88 WXN15 is a milling insert designed for productive machining of non‑ferrous metals, offering a sharp uncoated cutting grade within the Walter N‑Sortensystem. WXN15 uncoated carbide for NE‑metals Parallelogram 85° geometry for versatile milling 15° relief angle for secure cutting action G88 chipbreaker for controlled chip formation Precise chip control for reliable non‑ferrous machining The insert’s G88 chipbreaker and the WXN15 uncoated carbide grade are specifically configured for non‑ferrous materials such as aluminium, copper and brass. This combination reduces material adhesion and promotes consistent chip evacuation, which leads to fewer interruptions in production and less manual cleaning of components. The result is a measurable improvement in process stability and surface integrity when compared with blunt or incorrectly matched grades, making the insert especially suitable for shops seeking predictable throughput on NE‑metal families. Geometry that enhances stability and repeatability The parallelogram 85° shape with a 15° relief angle and a 1.6 mm corner radius delivers a balance between cutting strength and fine edge definition. These geometric choices contribute to a stable cutting edge under variable feed conditions and help maintain dimensional accuracy during profile milling and slotting operations. The insert’s geometry and tolerance class H provide repeatable seating and orientation in compatible toolholders, reducing setup time and ensuring consistent results across batches. System compatibility and application guidance for production use As part of the Walter N‑Sortensystem, the insert integrates into established milling tool families, offering straightforward interchangeability and inventory management. The uncoated, sharp grade is optimised for short to medium engagement milling, where built‑up edge is a primary concern; in such applications the insert helps achieve better surface finish and reduces the need for secondary operations. For further machining parameters or to verify suitability for a specific alloy, Metav Werkzeuge provides application guidance and can assist with insertion into existing tool assemblies. Contact Metav Werkzeuge for tailored application advice and to arrange supply of Walter Tools ADHT120416R-G88 WXN15 inserts directly through their distribution network Technical data SKU: ADHT120416R-G88-WXN15-WALTER Type: Fräswendeschneidplatte (milling insert) Designation: ADHT120416R-G88 WXN15 Manufacturer: Walter Tools Facts Relief angle: 15° Corner radius: 1.6 mm Plate form: Parallelogram 85° Plate size: 12 Plate thickness: 04 Chipbreaker: G88 Grade/Sort: WXN15 Series: Walter N‑Sortensystem Tolerance class: H Special features Uncoated carbide grade for NE‑metals Optimised for aluminium, copper and brass Sharp cutting edge for reduced adhesion Compatible with Walter N tool families Ausführung: T FAQ What materials is this insert suited for? The ADHT120416R-G88 WXN15 insert is designed for non‑ferrous metals (N group), including aluminium, copper and brass; the WXN15 uncoated carbide supports sharp‑edge applications to avoid material build‑up. How does the G88 chipbreaker improve machining? The G88 chipbreaker on this milling insert shapes and controls chips to reduce clogging and improve evacuation, which enhances surface finish and steady‑state cutting performance with NE‑metals. What does the parallelogram 85° shape offer in practice? The parallelogram 85° geometry allows versatile approach angles for profiling and face milling while keeping a robust cutting edge; it supports repeatable seating and stable force distribution in the holder. Is the insert part of a larger system for inventory management? Yes, the insert belongs to the Walter N‑Sortensystem, enabling compatibility with matching toolholders and simplifying spare‑part logistics within Walter tool families. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Protected trademarks and trade names are the property of their respective owners. Brand names and protected trade names are mentioned solely for explanatory purposes. There is no connection between our company and the mentioned brands. The offered item is an original, brand‑new product from the manufacturer. The Walter AG (brand presentation: Walter Tools), headquartered in Tübingen, is one of the world’s leading manufacturers of precision tools for metalworking and is part of the Sandvik group.
ADHT120430L-G88 WXN15 WXN15 Wendeplatten - Walter Tools
Take advantage of the combination of sharp, uncoated cutting geometry and targeted chip control to achieve cleaner surfaces and reliable batch processing; order the insert directly via Metav Werkzeuge or consult the team for tailored cutting data. ADHT120430L-G88 WXN15 — Fräswendeschneidplatte for non‑ferrous metals, Walter Tools ADHT120430L-G88 WXN15 is a parallelogram milling insert engineered for sharp, uncoated cutting of non‑ferrous metals such as aluminium, copper and brass Uncoated carbide WXN15 for sharp cutting 15° relief angle for low cutting forces Parallelogram 85° shape for reliable engagement G88 chipbreaker for controlled chip formation Faster, cleaner cuts in non‑ferrous components The ADHT120430L-G88 WXN15 is designed around the WXN15 uncoated grade to deliver very sharp edges and low adhesion when machining non‑ferrous metals. The combination of a keen cutting edge and the G88 chipbreaker reduces material build‑up and promotes predictable chip ejection, which directly supports higher effective machining rates and less secondary cleaning. For operations where surface appearance and minimal burr formation are decisive, this configuration offers a pragmatic balance between immediate cutting performance and process stability. Reduced cutting forces and improved process stability The insert’s 15° relief angle reduces radial cutting resistance and helps maintain consistent contact conditions at the cutting edge. The geometry, paired with a 3 mm corner radius, provides a compromise between edge strength and the ability to produce fine surface finishes; the radius dampens micro‑vibrations without sacrificing sharpness. These design choices translate into lower tool load variation and a steadier machining rhythm, which is particularly beneficial during medium‑depth finishing passes on softer alloys. Geometry tailored for predictable engagement The parallelogram 85° form supports a defined approach angle that aids in predictable tool engagement and chip flow across a wide range of feeds. Used within the Walter N grade system, the insert suits applications that require sharp, uncoated performance—especially where sticky or adhesive tendencies in the workpiece material can lead to built‑up edge. The arranged geometry simplifies fixture planning and contributes to consistent results across repeated cycles, helping to reduce scrap rates in batch production. Practical benefits for workshop integration Because the grade is uncoated carbide, it is particularly effective on aluminium and other non‑ferrous alloys where coatings can increase friction and promote material sticking. The clear chip control afforded by the G88 chipbreaker reduces manual chip clearing and lowers the frequency of interruptive interventions. For process planners this means improved uptime and a smoother workflow when the focus is on surface integrity and short‑cycle repeatability rather than heavy interrupted cutting. Choosing the right insert for the job Select this insert when priority is given to clean edges, minimal material adhesion and straightforward chip evacuation in non‑ferrous machining. The combination of the WXN15 uncoated grade and the specific edge geometry makes it a pragmatic choice for finish and light‑to‑medium machining tasks on aluminium, copper and brass alloys. For unusual alloys or special process constraints, technical advisors can help align the insert geometry with required feeds and toolpath strategies. Contact Metav Werkzeuge for tailored advice on Walter Tools ADHT120430L-G88 WXN15 and to discuss optimal cutting data or availability Technical Data SKU: ADHT120430L-G88-WXN15-WALTER Description: Fräswendeschneidplatte ADHT120430L-G88 WXN15 Walter Tools Manufacturer: Walter Tools Facts Relief angle: 15° Corner radius: 3 Plate form: Parallelogramm 85° Plate size: 12 Plate thickness: 04 Special features Walter N grade system Sorte: WXN15 (uncoated carbide) Chipbreaker: G88 Series: Walter N‑Sortensystem Application: non‑ferrous metals (aluminium, copper, brass) FAQ What materials is this insert best suited for? The ADHT120430L-G88 WXN15 is intended for non‑ferrous metals such as aluminium, copper and brass, where its sharp, uncoated geometry minimises adhesion. Is the WXN15 grade coated or uncoated? The WXN15 grade is an uncoated carbide grade designed for sharp cutting and low adhesion in NE‑metal applications. How does the G88 chipbreaker affect machining? The G88 chipbreaker is configured to produce predictable, manageable chips and to reduce material build‑up on the cutting edge during finish and light machining passes. What benefits does the parallelogram 85° shape provide? The parallelogram 85° form offers a defined engagement angle for steady cutting contact and improved chip evacuation across common milling strategies. Manufacturer/Responsible: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen; Germany Protected trademarks and trade names are the property of their respective owners. Brand names are used for explanation only and do not imply any affiliation between our company and the named manufacturers. The offered article is an original, factory‑new product from the manufacturer.
ADHT1204PEL-G88 WXN15 Wendeplatten - Walter Tools
The word 'messung' should be corrected to 'brass'. Order via Metav Werkzeuge or contact our consultants for tailored tooling advice. ADHT1204PEL-G88 WXN15 — indexable milling insert, parallelogram 85°, 15° relief — Walter Tools ADHT1204PEL-G88 WXN15 is an indexable milling insert engineered for efficient, burr‑reduced machining of non‑ferrous materials within the Walter N‑series tooling concept. Uncoated carbide grade WXN15 Optimised G88 chipbreaker Parallelogram 85° insert form 15° relief angle for sharp edges High‑speed productivity for non‑ferrous alloys The WXN15 grade is an uncoated carbide designed specifically for machining non‑ferrous metals such as aluminium, copper and brass. Its sharp cutting geometry reduces the tendency for material adherence and built‑up edge, which in turn improves surface finish and allows for higher feed rates without compromising component quality. Where sticky materials otherwise impair productivity, this insert keeps cycle times stable while maintaining consistent edge condition. Reliable chip control and stable cutting The G88 chipbreaker provides controlled chip formation and efficient evacuation, reducing recutting and the risk of edge damage. Combined with the parallelogram 85° form and 15° relief, the geometry ensures better access in shoulder and profile milling while delivering vibration damping and reproducible cutting forces. For workshops requiring predictable outcomes, the insert's geometry translates into fewer process interruptions and reduced scrap rates. System compatibility and economical operation As part of the Walter N‑series, the insert is intended for sharp, uncoated applications on non‑ferrous materials and integrates into established milling systems that accept ADHT‑style plates. The result is a balance of tool life and reliable performance that supports continuous production: sharp edges for quality surfaces, precise chip control for machine uptime, and straightforward reconditioning cycles where applicable. For specific cutting data and matching toolholders, Metav Werkzeuge provides application support to align feeds and speeds with machining goals. Contact Metav Werkzeuge for expert selection of Walter Tools inserts with WXN15 grade and G88 chipbreaker; phone +49 2822 7131930 or email info@metav-werkzeuge.com to discuss suitable toolholder pairings and delivery options. Technical data Article number: ADHT1204PEL-G88-WXN15-WALTER Designation: ADHT1204PEL-G88 WXN15 Series: Walter N-Sortensystem Manufacturer: Walter Tools Key dimensions Insert size: 12 Thickness: 04 Relief angle: 15° Plate form: Parallelogramm 85° Tolerance class: H Features / Applications Chipbreaker: G88 Grade: WXN15 (uncoated carbide) Suitable for: non‑ferrous metals (N) Execution: T Insert type: indexable milling insert FAQ Is this insert suitable for aluminium machining? Yes. The ADHT1204PEL-G88 WXN15 insert from Walter Tools is optimised for aluminium and other non‑ferrous metals, offering sharp edges and reduced material adhesion for improved surface finish. What benefit does the G88 chipbreaker provide? The G88 chipbreaker forms short, controllable chips and directs them away from the cutting zone, reducing recutting and promoting steady cutting forces for consistent process behaviour. Why choose the parallelogram 85° form and 15° relief? The parallelogram 85° shape increases approach flexibility in profile and shoulder milling, while the 15° relief maintains a sharp cutting geometry that lowers cutting forces and helps prevent built‑up edge. Is the WXN15 grade coated? No. WXN15 is an uncoated carbide grade intended for sharp, low‑adhesion applications on non‑ferrous materials, where coatings can sometimes increase friction. What production advantages can be expected in series machining? Using the Walter N‑series plates with WXN15 and G88 typically yields improved repeatability, fewer interruptions due to better chip control, and a predictable surface quality at higher feeds. Manufacturer/Responsible: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen Protected trademarks and product names belong to their respective owners. Brand names and registered trademarks are used for explanation only. There is no affiliation with the mentioned manufacturers; the offer concerns original, factory‑new items from the stated brand.
ADHT1204PER-G88 WK10 T Wendeplatten - Walter Tools
Take advantage of the combination of the uncoated WK10 carbide grade and the G88 chipbreaker for consistent chip control and sustained performance; the Parallelogram 85° form with 15° clearance enables flexible mounting and stable cutting. Order via Metav Werkzeuge or request technical advice from the consultants for precise grade selection. ADHT1204PER-G88 WK10 Fräswendeschneidplatte – Parallelogram 85°, 15° clearance (Walter Tools) The ADHT1204PER-G88 WK10 is a milling indexable insert designed for versatile positioning and dependable chip control in industrial milling applications. Walter Tools insert ADHT1204PER-G88 WK10 Parallelogram 85° shape for flexible positioning 15° clearance angle for stable cutting Uncoated carbide grade WK10, reliable wear resistance Accurate chip control for consistent machining The ADHT1204PER-G88 WK10 insert combines an engineered G88 chipbreaker with an uncoated carbide substrate to deliver controlled chip formation and predictable cutting forces. This combination reduces the risk of interrupted cuts and supports process stability on compatible workpieces; suitability for specific materials should be verified against the product matrix. The insert form and chip geometry are intended to promote steady material removal and to contribute to longer tool life under stable cutting conditions. Flexible clamping and quick indexability to reduce downtime The Parallelogram 85° configuration and compact dimensions (insert size 12, thickness 04) allow multiple clamping orientations, simplifying insert indexing and setup. With tolerance class H, repeatable seating is supported, which helps to reduce adjustment time during tool changes. These attributes translate into improved machine utilization and a more economical production flow when combined with a standardised tooling system. Specification guidance and selection for production needs For correct application, the WK10 grade and the insert geometry should be matched to the machining task via the manufacturer’s product matrix; the series is part of Walter’s open grade offering. Where process reliability is required, documentation on clearance angle, chipbreaker type and dimensional tolerances assists in selecting the right insert. Metav Werkzeuge can supply batch availability data and grade comparisons to ensure the chosen insert meets the operational goal of steady, productive cutting. Contact Metav Werkzeuge for specification support and availability of Walter Tools ADHT1204PER-G88 WK10 inserts on +49 2822 7131930 or info@metav-werkzeuge.com Technical data Article number: ADHT1204PER-G88-WK10-WALTER Designation: ADHT1204PER-G88 WK10 SKU: ADHT1204PER-G88-WK10-WALTER Facts Clearance angle: 15° Shape: Parallelogram 85° Insert size: 12 Thickness: 04 Tolerance class: H Special features Chipbreaker: G88 Grade: uncoated carbide WK10 Series: Walter grade series (open) Form: Parallelogram, 85° orientation Manufacturer: Walter Tools FAQ What materials is this insert suitable for? Material suitability must be verified in the manufacturer’s product matrix; the ADHT1204PER-G88 WK10 is an uncoated carbide insert whose best-fit materials depend on the specific grade recommendations. How does the G88 chipbreaker affect machining? The G88 chipbreaker promotes controlled chip formation and improved chip evacuation, enhancing process stability when the ADHT1204PER-G88 WK10 insert is used under recommended cutting conditions. Can the parallelogram 85° shape be used for different cutter types? Yes, the parallelogram 85° shape allows alternative mounting orientations and is compatible with milling cutters designed for this insert geometry, improving flexibility in cutter design. What does tolerance class H imply for setup? Tolerance class H indicates consistent dimensional accuracy for repeatable seating and reliable indexing, which supports fast tool changes and predictable positioning of the insert. Is the WK10 grade coated? No; the WK10 grade specified for this insert is an uncoated carbide grade and should be selected based on the application matrix and operational requirements. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Protected trademarks and trade names are the property of their respective owners. Brand names and protected designations (Walter Tools) are mentioned solely to explain product compatibility. There is no connection between Metav Werkzeuge and the mentioned brands. The offered item is original, factory-new goods of the manufacturer.
ADHT1204PER-G88 WXN15 WXN15 Wendeplatten - Walter Tools
The combination of a sharp, uncoated carbide grade and a G88 chipbreaker ensures reliable swarf control and efficient machining of non‑ferrous materials, improving productivity in batch and serial milling. Order the insert directly via Metav Werkzeuge or contact our specialists for application advice. ADHT1204PER-G88 WXN15 milling insert for non‑ferrous metals — Walter Tools The ADHT1204PER-G88 WXN15 is a parallelogram‑style milling insert with a 15° relief angle, optimised for sharp, uncoated cutting performance in non‑ferrous metal machining. Parallelogram 85° geometry for versatile milling Sharp uncoated carbide grade WXN15 G88 chipbreaker for controlled swarf formation 15° relief angle for reduced cutting forces High‑efficiency milling of non‑ferrous materials The ADHT1204PER‑G88 WXN15 is designed around a sharp, uncoated carbide grade that favours low adhesion and clean shearing when machining non‑ferrous metals such as aluminium and copper alloys. The combination of an acute cutting geometry and the WXN15 material class produces a keen cutting edge that reduces built‑up edge formation and promotes consistent surface finish. For applications where friction and material sticking are critical, this insert supports stable cutting behaviour and predictable tool life. Controlled chip formation and extended edge life The G88 chipbreaker provides dependable swarf control, directing chips away from the cutting zone to prevent recutting and minimise heat concentration. Together with the 15° relief angle, this geometry lowers cutting forces and helps maintain a steady, sharp edge over successive passes. The result is improved process reliability during continuous milling operations and fewer interruptions for edge changes, supporting a more efficient production flow. Practical handling and series compatibility for production Part of the Walter N‑grade system, this insert is classified for sharp, uncoated use with non‑ferrous workpieces and is produced to a tolerance class H for consistent dimensions. The parallelogram (85°) shape provides flexibility in cutter indexing and can be selected when a balance of radial and axial engagement is required. By choosing an insert from a coherent grade series, procurement and inventory management become simpler, helping to streamline tool selection and maintain productive machining across different workpieces. Contact Metav Werkzeuge for availability, detailed application guidance and to discuss how Walter Tools inserts like the ADHT1204PER‑G88 WXN15 can optimise current milling cycles — eMail: info@metav-werkzeuge.com, Tel: +49 2822 7131930 Technical Data SKU: ADHT1204PER-G88-WXN15-WALTER Article designation: ADHT1204PER-G88 WXN15 Product type: Fräswendeschneidplatte Manufacturer: Walter Tools Facts Plate size: 12 Thickness code: 04 Relief angle: 15° Plate form: Parallelogram 85° Tolerance class: H Special features Grade: WXN15 (uncoated carbide) Chipbreaker: G88 Series: Walter N‑grade system Application: Non‑ferrous metals (ISO group N) Free angle: 15° FAQ What materials is this insert intended for? The ADHT1204PER‑G88 WXN15 is intended primarily for non‑ferrous metals (ISO group N), including aluminium alloys and similar materials. Is the WXN15 grade coated or uncoated? The WXN15 grade is an uncoated carbide grade optimised for sharp‑edge performance in non‑ferrous machining. How does the G88 chipbreaker affect machining? The G88 chipbreaker helps control chip shape and evacuation, reducing the risk of recutting and improving stability in continuous milling operations. What is the significance of the parallelogram 85° form? A parallelogram 85° geometry offers a balanced engagement for radial and axial cutting forces, useful where a defined cutting orientation and indexable positions are required. Which series does this insert belong to and what does that mean for procurement? This insert is part of the Walter N‑grade system, which standardises grade characteristics for easier tool selection and consistent performance across matching applications. Manufacturer/Responsible: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen Trademarks and trade names are the property of their respective owners. Brand names and protected designations are mentioned for explanatory purposes only. There is no connection between our company and the mentioned brands. The offered item is original, brand‑new goods from the manufacturer.
ADHT160616R-G88 WK10 Wendeplatten - Walter Tools
Take advantage of the combination of reliable cutting performance, a 15° clearance angle and a 1.6 mm corner radius for productive milling operations; order the ADHT160616R-G88 WK10 milling insert directly via Metav Werkzeuge or ask the consultants if needed. ADHT160616R-G88 WK10 milling insert — 15° clearance, 1.6 mm corner radius — Walter Tools The ADHT160616R-G88 WK10 is a parallelogram 85° milling insert designed for general face and shoulder milling where an uncoated carbide grade is required and consistent chip control is essential. 15° clearance angle for positive cutting 1.6 mm corner radius for robust edges Parallelogram 85° insert geometry Uncoated carbide grade WK10 Increased productivity through predictable chip control The parallelogram geometry combined with the G88 chipbreaker enables controlled chip formation during interrupted and continuous cuts, which reduces recutting and improves process stability. This geometry, together with the 15° clearance angle, lowers cutting forces in many milling conditions and can translate into smoother feed rates and fewer tool changes. For production environments where cycle time and repeatability matter, the insert’s design supports a steady machining rhythm and clearer planning of tool life. Material suitability and application guidance The insert is supplied in the WK10 grade — an uncoated carbide option within Walter’s open series — and its material matrix should be consulted to determine optimal workpiece compatibility. The designation indicates an economical, general-purpose carbide; however, the specific workpiece materials and cutting parameters must be verified in the product matrix before use. When chosen appropriately, this grade can offer a balance between edge strength and cost-efficiency for a range of machining tasks. Robust edge life thanks to geometry and radius A 1.6 mm corner radius increases the strength of the cutting edge and reduces vulnerability to chipping under heavy loads or interrupted cuts. The insert’s parallelogram 85° form provides a stable seat and a positive cutting orientation that concentrates the cutting forces favourably for shoulder milling. In practice, a larger corner radius can permit higher feed per tooth while preserving surface quality, making the geometry suitable for both light finishing passes and more aggressive material removal where machine rigidity allows. Practical benefits for workshop efficiency Specified as ADHT160616R-G88 WK10, this insert is straightforward to integrate into existing toolholders that accept the parallelogram 85° form. The combination of a dedicated chipbreaker, defined clearance angle, and a reinforced corner reduces downtime from edge failure and streamlines tool management. By selecting the correct insert geometry and grade for the job and referring to the technical matrix for cutting data, shops can achieve better tool utilisation and predictable part quality without unnecessary over-specification. For personalised application advice or to check immediate availability of genuine Walter Tools inserts, contact Metav Werkzeuge (info@metav-werkzeuge.com / +49 2822 7131930) for consultation and ordering. Technical data Article number: ADHT160616R-G88-WK10-WALTER Designation: ADHT160616R-G88 WK10 Product type: Milling insert Manufacturer: Walter Tools Series: Walter Schneidstoffsorte - Serie offen Grade: WK10 Execution: T Tolerance class: H Numbers / core technical data Clearance angle: 15° Corner radius: 1.6 mm Insert size: 16 Thickness code: 06 Designs / special features Insert shape: Parallelogram 85° Chipbreaker: G88 Material information: Katalogabhängig ISO designation: ADHT160616R-G88 WK10 Notes: Sorteneinsatz / Werkstoffeignung prüfen anhand der Produktmatrix FAQ What materials is this insert suitable for? The ADHT160616R-G88 WK10 is an uncoated carbide grade; suitability depends on the workpiece and cutting data — check the product matrix for specific material recommendations. Is the 1.6 mm corner radius suitable for finishing? A 1.6 mm corner radius provides robustness and can be used for light finishing where a slightly stronger edge is acceptable; for fine finish requirements, consider smaller radii supported in the same series. Which chipbreaker does this insert use and why does it matter? This insert features the G88 chipbreaker, designed to promote controlled chip formation and reduce recutting, which helps maintain process stability during both interrupted and continuous milling. Can this insert be used for shoulder milling? Yes, the parallelogram 85° form and positive clearance angle make the insert appropriate for shoulder milling applications when matched with suitable holders and cutting parameters. What should be checked before selecting this insert for production? Before selection, verify workpiece material compatibility and recommended cutting data in the WK10 product matrix and confirm holder compatibility for the parallelogram 85° form. Manufacturer/Responsible: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen; Germany The Walter AG (brand appearance: Walter Tools) is part of the Sandvik group and is a globally recognised manufacturer of precision tools for metalworking. Protected trademarks and trade names remain the property of their respective owners. Brand names are mentioned for explanatory purposes only; there is no affiliation between our company and the named brands. The offered item is an original, brand-new product from the manufacturer.
ADHT160616R-G88 WXN15 T Wendeplatten - Walter Tools
Take advantage of a precise cutting geometry and a sharp, uncoated carbide grade optimised for non‑ferrous metals to maintain high process stability and low material adhesion. Order the insert directly via Metav Werkzeuge or consult our specialists for application guidance. ADHT160616R-G88 WXN15 milling indexable insert – 15° clearance, 1.6 mm corner radius | Walter Tools ADHT160616R-G88 WXN15 is a milling indexable insert designed for sharp, uncoated performance when machining non‑ferrous materials such as aluminium and copper Uncoated carbide for non‑ferrous metals Sharp cutting edge for minimal adhesion Parallelogram 85° geometry for axial milling 15° clearance angle for secure chip flow Reliable cutting for non‑ferrous machining The insert offers an uncoated carbide composition coupled with a very sharp cutting edge, specifically engineered for machining non‑ferrous metals. This combination reduces the tendency for material to stick to the cutting edge, which in turn improves surface finish and reduces rework. The product’s grade, WXN15, is specified for clean, burr‑reduced cutting in aluminium, copper and similar alloys, delivering predictable tool life in repetitive production tasks. By choosing this geometry, workshops benefit from consistent chip formation and improved process reliability. Geometry that supports efficient milling Featuring a parallelogram 85° form and a corner radius of 1.6 mm, the insert provides a balance between edge strength and sharpness. The 85° approach angle is advantageous for axial milling operations where stable cutting forces and controlled chip evacuation are required. The 15° clearance angle further reduces rubbing along the flank, lowering heat build‑up and wear. These geometrical attributes translate into smoother feeds, longer edge life and fewer tool changes, which increases machine availability and reduces cycle times. Application advantages and practical benefits Built into the Walter N‑grade system, this insert is intended for productive machining of non‑ferrous materials under a variety of conditions. The G88 chipbreaker geometry promotes predictable chip segmentation, reducing clogging in continuous cuts and enabling higher average feed rates. For manufacturers seeking to optimise throughput without sacrificing surface quality, the combination of grade and chipformer supports more stable cutting and easier downstream handling of chips, contributing to a more economical machining process. For application support, availability or to discuss suitable holder combinations for the Walter Tools ADHT160616R-G88 WXN15 insert, contact Metav Werkzeuge for tailored advice and ordering assistance Technical Data SKU: ADHT160616R-G88-WXN15-WALTER Designation: ADHT160616R-G88 WXN15 Product type: Milling indexable insert Series: Walter N‑Sortensystem Manufacturer: Walter Tools Numbers / Core technical data Size designation: 16 Thickness designation: 06 Clearance angle: 15° Corner radius: 1.6 mm Plate form: Parallelogram 85° Special features / Versions Grade: WXN15 Chipbreaker: G88 Coating: Uncoated carbide Execution: T Tolerance class: H FAQ What materials is this insert intended for? The ADHT160616R-G88 WXN15 insert is specified for non‑ferrous metals (ISO group N), such as aluminium, copper and brass, where a very sharp, uncoated cutting edge is required. Is the insert coated or uncoated? This item is an uncoated carbide insert in the Walter N‑grade family, optimised for low adhesion when machining soft, non‑ferrous alloys. How does the G88 chipbreaker affect machining? The G88 chipformer promotes controlled chip segmentation, which helps prevent clogging and supports higher continuous feed rates in typical axial milling operations. Which geometry benefits axial milling applications? The parallelogram 85° form combined with a 15° clearance angle delivers stable cutting forces and improved chip flow, making it suitable for axial milling where good surface quality is required. Can this insert be used in heavy roughing operations? The insert’s 1.6 mm corner radius and sharp grade are geared towards finishing to medium cutting conditions in non‑ferrous materials; for heavy roughing in other material groups, alternative geometries or grades should be considered. Walter Tools: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen, Germany Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenzeichen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers.
ADHT1606PEL-G88 WXN15 Wendeplatten - Walter Tools
Reliable machining of non‑ferrous materials is achieved through the combination of a sharp uncoated carbide grade (WXN15) and the G88 chipbreaker with a 15° clearance, delivering clean chips and reduced adhesion for efficient production. Benefit from the Walter N‑series' proven geometry for consistent results and long tool life. Order the ADHT1606PEL-G88 WXN15 directly via Metav Werkzeuge or ask our consultants if needed. ADHT1606PEL-G88 WXN15 – Parallelogram 85°, 15° clearance indexable milling insert for non‑ferrous metals, Walter Tools The ADHT1606PEL-G88 WXN15 is an indexable milling insert engineered for sharp, low‑adhesion machining of NE‑metals such as aluminium, copper and brass, combining an uncoated carbide grade with a G88 chipbreaker and a parallelogram 85° form for versatile chamfering and face milling. Parallelogram 85° geometry for versatile milling 15° clearance angle for sharp edge engagement Uncoated carbide grade WXN15 for NE‑metals G88 chipbreaker reduces material adhesion Cleaner chip control and better surface finish with NE‑metals The insert’s G88 chipbreaker and uncoated carbide construction are tailored to the demands of non‑ferrous alloys. Sharp cutting edges minimise material build‑up and prevent smearing on the cutting edge, which is critical when working with aluminium and brass. This leads to improved surface quality and reduced secondary operations. For shops aiming to cut cycle time and scrap rates, the geometry helps maintain consistent chip evacuation and stable cutting forces, translating into reliable part quality in batch production. Stable cutting performance through optimised geometry The Parallelogram 85° outline combined with a 15° clearance provides a controlled, repeatable engagement angle that supports stable cutting and predictable tool behaviour. The insert thickness and ground seating ensure accurate clamping and repeatable positioning in toolholders, which maintains dimensional consistency across workpieces. By favouring precise geometry over excessive coatings for this application, the grade WXN15 offers predictable wear characteristics and dependable edge integrity under typical non‑ferrous cutting conditions. Process security and productivity benefits for series production Placed in the Walter N‑series, this insert is designed for straightforward tool selection and quick index changes, supporting productive machining workflows. The combination of a sharp grade and a dedicated chipbreaker reduces downtime associated with rework and cleaning, while enabling higher feed rates where appropriate. The insert’s properties contribute to lower total machining costs by reducing cycle time and improving first‑pass yield, providing measurable benefits for manufacturing environments focused on throughput and consistency. Contact Metav Werkzeuge for tailored application advice and prompt supply of Walter Tools inserts; professional consultants are available to discuss optimal toolholder pairing and cutting parameters Technical Data Article number: ADHT1606PEL-G88-WXN15-WALTER Type: Indexable milling insert ISO designation: ADHT1606PEL-G88 WXN15 Series: Walter N‑series Grade: WXN15 Facts Insert size: 16 Thickness: 06 Clearance angle: 15° Geometry: Parallelogram 85° Tolerance class: H Special features Uncoated carbide (sharp grade for NE‑metals) G88 chipbreaker for reduced adhesion Suited to aluminium, copper, brass (NE‑metals) Designed for sharp/uncoated applications in the Walter N‑series FAQ What materials is this insert intended for? The ADHT1606PEL-G88 WXN15 is intended for NE‑metals; it is optimised for aluminium, copper and brass machining using the sharp WXN15 grade. Does the insert require a coated grade for longer life? For non‑ferrous applications the uncoated WXN15 grade with the G88 chipbreaker offers superior performance by preventing material build‑up; coated grades are typically chosen for different material groups. Which toolholders are compatible with the ADHT1606PEL-G88 WXN15? Compatibility depends on the toolholder seat and clamping system; the insert’s parallelogram 85° form is compatible with holders designed for ADHT‑style inserts and standard clamping systems for this insert family. How does the G88 chipbreaker affect machining parameters? The G88 chipbreaker promotes short, consistent chips and lower adhesion, which often permits higher feed rates and improved surface finish when machining non‑ferrous alloys with the ADHT1606PEL-G88 WXN15. Is this insert part of a broader system for easy reordering? Yes, it belongs to the Walter N‑series and is designated ADHT1606PEL‑G88 WXN15, which simplifies tool selection and replenishment within the Walter Tools portfolio. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenzeichen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers.
ADHT1606PER-G88 WK10 Wendeplatten - Walter Tools
Take advantage of the combination of reliable chip control, a rigid parallelogram 85° geometry and the WK10 uncoated carbide grade for productive milling operations; order directly via Metav Werkzeuge or request application advice from the specialists. ADHT1606PER-G88 WK10 milling insert (Parallelogram 85°, 15° clearance) – Walter Tools The ADHT1606PER-G88 WK10 is a milling insert engineered for medium-duty finishing and semi-finishing applications where stable chip formation and predictable edge life are required. Parallelogram 85° insert shape 15° clearance angle for stable cutting WK10 uncoated carbide grade G88 chipbreaker for controlled chips Stable chip control that improves cycle consistency The combination of the G88 chipbreaker and the insert geometry delivers consistent chip formation, which reduces rework and eases chip evacuation in automated and manual milling processes. The chipbreaker is designed to break chips into short, manageable segments; this lowers the risk of recutting and helps to maintain tool life. For production environments where process reliability matters, predictable chip behaviour translates directly into fewer interruptions and higher throughput. Material grade and wear performance explained Supplied in the WK10 grade, this insert is made from an uncoated carbide formulation intended for a broad range of general machining tasks. The uncoated nature favours operations where thermal or mechanical loading is moderate and where regrinding or specific machinability is required. Assessments against the product matrix are advised to confirm suitability for particular workpiece materials and cutting conditions; verifying the grade against the intended application ensures optimal wear behaviour and repeatable results. Geometry that supports precision and accessibility The parallelogram 85° shape and 15° clearance angle offer a balance between rigidity and approachability in tight or stepped features. The angular form provides improved accessibility for shoulder milling while maintaining a secure seat in the toolholder, which helps to reduce vibration and produce a consistent surface finish. The thickness code (06) contributes to the assembly’s stiffness; this is beneficial when maintaining dimensional accuracy across successive passes. Practical advantages for shop-floor integration As a standard insert format, this product integrates readily with common Walter-compatible toolholders used across industry. The concise geometry and chip control characteristics support both single-pass finishing and multi-pass semi-finishing strategies, helping to shorten set-up times and simplify inventory management. Operators and process engineers gain predictable tool performance, which supports process optimisation and cost-effective machining cycles. For productive, reliable milling with Walter Tools’ WK10-grade inserts, contact Metav Werkzeuge for tailored application guidance and quick availability through their technical sales team. Technical data Article number: ADHT1606PER-G88-WK10-WALTER SKU: ADHT1606PER-G88-WK10-WALTER Description: Fräswendeschneidplatte ADHT1606PER-G88 WK10 Manufacturer: Walter Tools Facts Clearance angle: 15° Insert size: 16 Thickness code: 06 Tolerance class: H Special features Chipbreaker: G88 Insert shape: Parallelogram 85° Grade: WK10 (uncoated carbide) Series: Walter Schneidstoffsorte - Serie offen Material designation: Catalogue-dependent FAQ What materials is this insert suited for? This insert in the WK10 grade is intended for general machining tasks; suitability for specific materials should be checked against the product matrix to confirm compatibility. How does the G88 chipbreaker affect machining? The G88 chipbreaker promotes short, manageable chips for improved evacuation and reduced risk of recutting when using the ADHT1606PER-G88 WK10 milling insert from Walter Tools. Can this insert be used for finishing and semi-finishing? Yes, the geometry and clearance angle make the insert appropriate for both finishing and semi-finishing strategies in compatible applications. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen, Germany Protected trademarks and trade names are the property of their respective owners. Brand names and registered trademarks are mentioned for explanatory purposes only. There is no connection between our company and the named brands. The offered item is original, factory-new goods of the manufacturer.
ADHT1606PER-G88 WXN15 WXN15 Wendeplatten - Walter Tools
Benefit from the combination of a sharp uncoated carbide grade WXN15 and an optimised G88 chipbreaker for reliable, burr‑reduced machining of non‑ferrous metals; combine easy indexability and consistent edge performance to keep production running smoothly. Order the insert directly via Metav Werkzeuge or request advice from our technical consultants. ADHT1606PER-G88 WXN15 milling indexable insert — Parallelogram 85°, 15° clearance by Walter Tools The ADHT1606PER-G88 WXN15 is a parallelogram milling insert engineered for efficient, sharp cutting of non‑ferrous metals such as aluminium, copper and brass in light to medium milling operations. Sharp uncoated carbide grade WXN15 Optimised G88 chipbreaker for non‑ferrous metals Parallelogram 85° form with 15° clearance Size 16, thickness 06 for stable seating Precision cutting for non‑ferrous materials that reduces rework The insert’s WXN15 composition is an uncoated carbide grade developed for applications in the non‑ferrous group. Its sharp cutting edge reduces material adhesion and built‑up edge, which helps to maintain a consistent cutting profile when machining aluminium, copper or brass. The result is fewer interruptions for edge dressing and less downstream finishing, which translates directly into improved process efficiency and reduced scrap rates. The G88 chipbreaker works in concert with the cutting geometry to break chips reliably and guide them away from the cutting zone, improving surface quality while protecting the tool seat from premature damage. Geometry that supports stable clamping and consistent surface finish The parallelogram 85° form with a 15° clearance angle ensures a secure seat in compatible tool holders and promotes stable cutting forces. This geometry reduces vibration during interrupted cuts and improves the repeatability of each indexed position. Stable seating and a predictable rake/clearance combination contribute to a more even surface finish and tighter dimensional control on the workpiece. For workshops seeking reliable, repeatable results, the insert’s form factor and precision tolerance class support predictable performance across multiple indexing cycles. Easy integration and measurable productivity gains Designed for the Walter N‑Sortensystem, the indexable insert format allows rapid replacement and straightforward inventory management. The combination of uncoated carbide and the G88 chipbreaker offers a cost‑effective option where sharpness and chip control are decisive, such as finishing or light roughing of non‑ferrous components. Reduced secondary operations and simpler tool handling lower labour and machine time per part. For production environments that value throughput without sacrificing part quality, this insert delivers a practical balance of economy and performance. Contact Metav Werkzeuge for tailored cutting data, availability and advice on integrating the ADHT1606PER-G88 WXN15 insert — eMail: info@metav-werkzeuge.com | Tel: +49 2822 7131930 Technical Data SKU: ADHT1606PER-G88-WXN15-WALTER Article designation: ADHT1606PER-G88 WXN15 Manufacturer: Walter Tools Product type: Milling indexable insert Series: Walter N‑Sortensystem Facts Size: 16 Thickness: 06 Clearance angle: 15° Plate form: Parallelogram 85° Tolerance class: H Special features Chipbreaker: G88 Grade: WXN15 (uncoated carbide) Intended materials: Non‑ferrous metals (N) Application note: Sharp, uncoated use for aluminium, copper, brass Format: Indexable milling insert (ADHT geometry) FAQ What materials is this insert intended for? The ADHT1606PER-G88 WXN15 insert is specified for non‑ferrous metals (N) such as aluminium, copper and brass, following the ISO 513 guidance noted in the product data. Is the cutting grade coated or uncoated? The insert uses an uncoated carbide grade, WXN15, optimised for sharpness and low adhesion in NE‑metal machining. How does the G88 chipbreaker affect performance? The G88 chipbreaker produces short, controllable chips in non‑ferrous materials and helps to reduce surface smearing and built‑up edge, improving finish and protecting the seat. Which tool series is this insert compatible with? The insert is part of the Walter N‑Sortensystem series and is intended for tool holders that accept ADHT‑style indexable inserts. What geometry features support stable cutting? The parallelogram 85° shape combined with a 15° clearance angle provides secure seating and reduced vibration, supporting consistent surface quality and dimensional control. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Protected trademarks and trade names are the property of their respective owners. Brand names and protected designations are mentioned for explanatory purposes only and do not imply any affiliation with our company. The offered item is an original, factory‑new product from Walter Tools.
ADKA CERMET 150308 Indexable Insert for Stahl, rostfreier Stahl, Guss - MetavCUT
Didn't find the right insert? We can help you!► Send us a photo of your insert by e-mail.► Send us your drawing by e-mail.► Send us your sample insert or drawing by post. Design details for ADKA CERMET 150308 indexable inserts from MetavCUT Brand: MetavCUT Manufacturer Order Number: ADKA150308SR-CERMET Data & Figures: ISO-Code: ADKA150308 Clearance Angle: 15° Angle: 85° Thickness: 3,18mm Radius: 0.8 Special features Material: CERMET with hole Hole Style: cylindrical hole Form: parallelogram Chip Breaker: without Manufacturer: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; www.metav-shop.de; info@metav-werkzeuge.com 40START indexable-inserts-ADKA CERMET-150308-Stahl, rostfreier Stahl, Guss-MetavCUT 40END
ADKA CERMET 150308 Indexable Insert for Stahl, rostfreier Stahl, Guss - MetavCUT
Are you unsure whether the tool is suitable for your application? Or are you still missing technical data?No problem, just contact us!!! 📧 eMail: info@metav-werkzeuge.com ☎️ Phone: +49 2822 7131930 ✔️ WhatsApp: +49 170 2837271 Product features for indexable inserts ADKA CERMET 150308 from MetavCUT Brand: MetavCUT Manufacturer Order Number: ADKA150308TR-CERMET Facts & Figures: ISO-Code: ADKA150308 Clearance Angle: 15° Angle: 85° Thickness: 3,18mm Radius: 0.8 Features Material: CERMET with hole Hole Style: cylindrical hole Form: parallelogram Chip Breaker: without Manufacturer: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; www.metav-shop.de; info@metav-werkzeuge.com 40START indexable-inserts-ADKA CERMET-150308-Stahl, rostfreier Stahl, Guss-MetavCUT 40END
ADKR 1503PD IC20 Indexable Insert - ISCAR
Unsure whether the tool is the right one? Or are you missing technical data?Just get in touch with us! 📧 eMail: info@metav-werkzeuge.com, ☎️ Phone: +49 2822 7131930, ✔️ WhatsApp: +49 170 2837271 Performance features for ADKR 1503PD indexable inserts from ISCAR Brand: ISCAR Manufacturer Order Number: ADKR1503PD-RIC20 Facts and Figures: ISO-Code: ADKR1503PD Clearance Angle: 15° Angle: 85° Thickness: 3,18mm Features Material: cemented carbide Grade: IC20 without hole Form: parallelogram Chip Breaker: single-sided Series: HELIMILL/HELI2000 Manufacturer: ISCAR Ltd.; Industrial Zone, P.O.Box 11; 24959 Tefen; Israel; www.iscar.so.il; info@iscar.co.il Brand names and registered trademarks are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. The brands mentioned are not in any contractual relationship with our company. The sales offer includes high-quality, new branded articles from the manufacturer ISCAR. 40START indexable-inserts-ADKR-1503PD-IC20-ISCAR 40END
ADKR 1503PD IC250 Indexable Insert - ISCAR
Not sure whether this tool is suitable for your application? Or are you still missing important technical details? No problem!Contact us - we will be happy to advise you. ✔️ WhatsApp: +49 170 2837271, ☎️ Phone: +49 2822 7131930, 📧 eMail: info@metav-werkzeuge.com Technical data indexable inserts ADKR 1503PD from ISCAR Brand: ISCAR Manufacturer Order Number: ADKR1503PD-RIC250 Data/ Figures: ISO-Code: ADKR1503PD Clearance Angle: 15° Angle: 85° Thickness: 3,18mm Special features Material: cemented carbide Grade: IC250 without hole Form: parallelogram Chip Breaker: single-sided Series: HELIMILL/HELI2000 Manufacturer: ISCAR Ltd.; Industrial Zone, P.O.Box 11; 24959 Tefen; Israel; www.iscar.so.il; info@iscar.co.il Registered trademarks and trade names are the property of their respective owners. The mention of protected trademarks and trade names is for illustrative purposes only. Named brands are in no way associated or co-operate with our company. The sales offer includes high-quality, new branded articles from the manufacturer ISCAR. 40START indexable-inserts-ADKR-1503PD-IC250-ISCAR 40END
ADKR 150504 IC28 Indexable Insert - ISCAR
Are you unsure whether the tool is suitable for your application? Or do you need further technical information?No problem - feel free to contact us! 📧 eMail: info@metav-werkzeuge.com ☎️ Phone: +49 2822 7131930 ✔️ WhatsApp: +49 170 2837271 Technical data for ADKR 150504 inserts from ISCAR Brand: ISCAR Manufacturer Order Number: ADKR150504PDR-HMIC28 Facts / Figures: ISO-Code: ADKR150504 Clearance Angle: 15° Angle: 85° Thickness: 5,56mm Radius: 0.4 Features Material: cemented carbide Grade: IC28 without hole Form: parallelogram Chip Breaker: single-sided Series: HELIMILL/HELI2000 Manufacturer: ISCAR Ltd.; Industrial Zone, P.O.Box 11; 24959 Tefen; Israel; www.iscar.so.il; info@iscar.co.il Brand names and registered trademarks are the property of their respective owners. The indication of brand names and trademarks is for information purposes only. Our company has no commercial, legal or other connection with the brands concerned. The items offered are original, brand-new goods of the ISCAR brand. 40START indexable-inserts-ADKR-150504-IC28-ISCAR 40END
ADKR 150504 IC328 Indexable Insert - ISCAR
Unsure whether the tool is the right one? Or are you missing technical data?Just get in touch with us! 📧 eMail: info@metav-werkzeuge.com ☎️ Phone: +49 2822 7131930 ✔️ WhatsApp: +49 170 2837271 Performance features for indexable inserts ADKR 150504 from ISCAR Brand: ISCAR Manufacturer Order Number: ADKR150504PDR-HMIC328 Data & Figures: ISO-Code: ADKR150504 Clearance Angle: 15° Angle: 85° Thickness: 5,56mm Radius: 0.4 Features Material: cemented carbide Grade: IC328 without hole Form: parallelogram Chip Breaker: single-sided Series: HELIMILL/HELI2000 Manufacturer: ISCAR Ltd.; Industrial Zone, P.O.Box 11; 24959 Tefen; Israel; www.iscar.so.il; info@iscar.co.il Registered trademarks and trade names are the property of their respective owners. The naming of brand names and protected trademarks is for descriptive purposes only. Mention of the brands does not imply any relationship to our company. This is a brand new original product of the leading brand ISCAR. 40START indexable-inserts-ADKR-150504-IC328-ISCAR 40END
ADKR 150504 IC950 Indexable Insert - ISCAR
Are you unsure whether the tool is suitable for your application? Or do you need further technical information?No problem - feel free to contact us! 📧 eMail: info@metav-werkzeuge.com, ☎️ Phone: +49 2822 7131930, ✔️ WhatsApp: +49 170 2837271 Product features indexable inserts ADKR 150504 from ISCAR Brand: ISCAR Manufacturer Order Number: ADKR150504PDR-HMIC950 Figures for the tool: ISO-Code: ADKR150504 Clearance Angle: 15° Angle: 85° Thickness: 5,56mm Radius: 0.4 Special features Material: cemented carbide Grade: IC950 without hole Form: parallelogram Chip Breaker: single-sided Series: HELIMILL/HELI2000 Manufacturer: ISCAR Ltd.; Industrial Zone, P.O.Box 11; 24959 Tefen; Israel; www.iscar.so.il; info@iscar.co.il Brand names and registered trademarks are the property of their rightful owners. The inclusion of registered trademarks and trade names is for illustrative purposes only. The brands mentioned are not in any contractual relationship with our company. The items offered are original, brand-new goods of the ISCAR brand. 40START indexable-inserts-ADKR-150504-IC950-ISCAR 40END
ADKR 1505PD IC28 Indexable Insert - ISCAR
Are you unsure whether the tool is suitable for your application? Or are you still missing technical data?No problem, just contact us!!! ✔️ WhatsApp: +49 170 2837271 ☎️ Phone: +49 2822 7131930 📧 eMail: info@metav-werkzeuge.com Specifications indexable inserts ADKR 1505PD from ISCAR Brand: ISCAR Manufacturer Order Number: ADKR1505PDR-HMIC28 Facts for the tool: ISO-Code: ADKR1505PD Clearance Angle: 15° Angle: 85° Thickness: 5,56mm Features Material: cemented carbide Grade: IC28 without hole Form: parallelogram Chip Breaker: single-sided Series: HELIMILL/HELI2000 Manufacturer: ISCAR Ltd.; Industrial Zone, P.O.Box 11; 24959 Tefen; Israel; www.iscar.so.il; info@iscar.co.il Registered brand names and trademarks are the property of their respective owners. The naming of brand names and protected trademarks is for descriptive purposes only. The brands mentioned are not in any contractual relationship with our company. This is a brand new original product of the leading brand ISCAR. 40START indexable-inserts-ADKR-1505PD-IC28-ISCAR 40END
ADKR 1505PD IC28 Indexable Insert - ISCAR
Unsure whether the tool is the right one? Or are you missing technical data?Just get in touch with us! 📧 eMail: info@metav-werkzeuge.com, ✔️ WhatsApp: +49 170 2837271, ☎️ Phone: +49 2822 7131930 Detail specifications for ADKR 1505PD insert from ISCAR Brand: ISCAR Manufacturer Order Number: ADKR1505PDL-HMIC28 Facts & Figures: ISO-Code: ADKR1505PD Clearance Angle: 15° Angle: 85° Thickness: 5,56mm Features Material: cemented carbide Grade: IC28 without hole Form: parallelogram Chip Breaker: single-sided Series: HELIMILL/HELI2000 Manufacturer: ISCAR Ltd.; Industrial Zone, P.O.Box 11; 24959 Tefen; Israel; www.iscar.so.il; info@iscar.co.il Brand names and registered trademarks are the property of their respective owners. The use of brand names and trademarks is for descriptive purposes only. Mention of the brands does not imply any relationship to our company. The sales offer includes high-quality, new branded articles from the manufacturer ISCAR. 40START indexable-inserts-ADKR-1505PD-IC28-ISCAR 40END
ADKR 1505PD IC328 Indexable Insert - ISCAR
Not sure whether this tool is suitable for your application? Or are you still missing important technical details? No problem!Contact us - we will be happy to advise you. 📧 eMail: info@metav-werkzeuge.com ☎️ Phone: +49 2822 7131930 ✔️ WhatsApp: +49 170 2837271 Design details for ADKR 1505PD indexable inserts from ISCAR Brand: ISCAR Manufacturer Order Number: ADKR1505PDR-HMIC328 Figures for the tool: ISO-Code: ADKR1505PD Clearance Angle: 15° Angle: 85° Thickness: 5,56mm Special features Material: cemented carbide Grade: IC328 without hole Form: parallelogram Chip Breaker: single-sided Series: HELIMILL/HELI2000 Manufacturer: ISCAR Ltd.; Industrial Zone, P.O.Box 11; 24959 Tefen; Israel; www.iscar.so.il; info@iscar.co.il Registered trademarks and trade names are the property of their respective owners. The designation of brand names and trademarks is for explanatory purposes only. Our company has no commercial, legal or other connection with the brands concerned. The sales offer includes high-quality, new branded articles from the manufacturer ISCAR. 40START indexable-inserts-ADKR-1505PD-IC328-ISCAR 40END
ADKR 1505PD IC328 Indexable Insert - ISCAR
Are you unsure whether the tool is suitable for your application? Or do you need further technical information?No problem - feel free to contact us! 📧 eMail: info@metav-werkzeuge.com, ☎️ Phone: +49 2822 7131930, ✔️ WhatsApp: +49 170 2837271 Technical data indexable inserts ADKR 1505PD from ISCAR Brand: ISCAR Manufacturer Order Number: ADKR1505PDL-HMIC328 Facts for the tool: ISO-Code: ADKR1505PD Clearance Angle: 15° Angle: 85° Thickness: 5,56mm Special features Material: cemented carbide Grade: IC328 without hole Form: parallelogram Chip Breaker: single-sided Series: HELIMILL/HELI2000 Manufacturer: ISCAR Ltd.; Industrial Zone, P.O.Box 11; 24959 Tefen; Israel; www.iscar.so.il; info@iscar.co.il Registered trademarks and trade names are the property of their respective owners. The use of brand names and trademarks is for descriptive purposes only. Mention of the brands does not imply any relationship to our company. The article presented is a brand-new original product of the ISCAR brand. 40START indexable-inserts-ADKR-1505PD-IC328-ISCAR 40END
ADKR 1505PD IC716 Indexable Insert - ISCAR
Not sure whether this tool is suitable for your application? Or are you still missing important technical details? No problem!Contact us - we will be happy to advise you. 📧 eMail: info@metav-werkzeuge.com, ☎️ Phone: +49 2822 7131930, ✔️ WhatsApp: +49 170 2837271 Product specifications for indexable inserts ADKR 1505PD from ISCAR Brand: ISCAR Manufacturer Order Number: ADKR1505PDR-HPIC716 Facts & Figures: ISO-Code: ADKR1505PD Clearance Angle: 15° Angle: 85° Thickness: 5,56mm Special features Material: cemented carbide Grade: IC716 without hole Form: parallelogram Chip Breaker: single-sided Series: HELIMILL/HELI2000 Manufacturer: ISCAR Ltd.; Industrial Zone, P.O.Box 11; 24959 Tefen; Israel; www.iscar.so.il; info@iscar.co.il Brand names and protected trademarks are the property of their respective owners. The mention of protected trademarks and trade names is for illustrative purposes only. Mention of the brands does not imply any relationship to our company. The sales offer includes high-quality, new branded articles from the manufacturer ISCAR. 40START indexable-inserts-ADKR-1505PD-IC716-ISCAR 40END
Why indexable inserts are indispensable in modern machining
Indexable inserts, also known as cutting inserts or indexable cutting inserts, are standardised, replaceable cutting elements that mount on tool holders such as turning bits, milling cutters or drills. Made from wear-resistant materials like carbide, cermet, ceramic or other superhard grades, they carry the actual cutting edge and allow a worn corner to be rotated or flipped instead of replacing or regrinding the entire tool body.
How these inserts work and when to choose them
In everyday workshop and production settings, indexable inserts perform the direct material removal on the workpiece. Standard inserts for tool systems without internal coolant typically feature closed faces or a single central fixing hole, with heat evacuation handled by external machine nozzles. Inserts designed for systems with internal coolant are engineered to support coolant flow: they include calculated chipbreaker geometries that guide an internal coolant jet under the chip or, in specialised designs, contain sintered microchannels to direct coolant right to the cutting edge. Such coolant-compatible inserts are essential for machining heat-resistant alloys, heavy cutting operations and deep internal machining, where thermal load and chip control are critical.
Tangible benefits for production and workshop efficiency
Choosing the right indexable inserts delivers measurable operational advantages:
- Reduced downtime: faster changeover because a worn insert is simply indexed rather than the whole tool being replaced.
- Extended cutting-edge life: targeted coolant application and optimised chipbreaker design lower thermal stress and improve tool life.
- Consistent part quality: predictable cutting-edge geometry from standardised inserts maintains tolerances across batches.
- Versatility: availability in carbide, cermet, ceramic and superhard grades permits selection according to workpiece material and cutting conditions.
- Lower tooling costs over time: fewer full-tool replacements and less regrinding required.
Metav as a dependable source for inserts and tooling systems
Metav combines decades of precision expertise with a wide-ranging supply chain, positioning itself as a practical partner for industry, craft and trade. From Emmerich on the Rhine, Metav operates as a quality filter for the European market, offering more than 250,000 products and serving over 48,000 customers. For procurement teams aiming to reduce supplier count while retaining technical reliability, Metav’s assortment of indexable inserts and compatible tool holders provides a central, trustworthy solution.
Quick summary
Indexable inserts (cutting inserts or indexable cutting inserts) enable economical, repeatable material removal by allowing worn cutting edges to be indexed or replaced quickly; coolant-adapted designs further reduce thermal load and enhance chip control for demanding applications.
FAQ
What materials are indexable inserts available in?
Indexable inserts are available in wear-resistant grades such as carbide, cermet, ceramic and other superhard materials, selected according to the workpiece material and cutting conditions.
When should I choose inserts with internal coolant support?
Choose inserts designed for internal coolant when machining heat-resistant alloys, performing heavy cuts or working in deep internal features, because the coolant reduces thermal load at the cutting edge and actively improves chip breakage.
How do chipbreaker geometries affect performance?
Chipbreaker geometries on indexable inserts guide the chip flow and, when matched to an internal coolant jet, direct the coolant under the chip to control temperature and facilitate reliable chip formation, which extends edge life and stabilises machining.
Can standard inserts be used with external coolant only?
Yes; standard inserts for tool systems without internal coolant typically have closed faces or a central fixing hole and rely on external machine nozzles for heat evacuation, which is sufficient for many routine, accessible cuts.
Why source inserts through Metav?
Metav supplies a broad range of indexable inserts and tooling, backed by decades of expertise and a comprehensive European stock, making it a practical choice for consistent quality and dependable delivery.
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com