105mm Three-Point Replacement Tips Ø12mm Carbide For Rod Calipers From 500mm - Metav IndustryLine

Take advantage of the combination of carbide wear resistance, precise Ø 12 mm mounting and a 105 mm reach to restore reliable contact on large calipers; order the replacement tips directly via Metav Werkzeuge or consult our specialists for fitment advice.

Replacement Tips for Bar-Divider Calipers (M201.175.1) – Carbide, 105 mm, Ø 12 mm (Metav IndustryLine)

A set of Replacement Tips for Bar-Divider Calipers (M201.175.1) intended to renew contact points on calipers with measuring ranges from 500 mm, designed for workshop and industrial metrology applications

• Carbide tips for extended wear resistance
• 105 mm length for deep measurements
• Ø 12 mm shank for secure mounting
• Compatible with M201.175–M201.178

Restore accurate contact on large-range calipers

Replacement contact points made from carbide deliver consistent repeatability for large-scale measurements. Installed on calipers with a measuring range classified as large-range (500–1,000 mm), the hardened tips resist wear that otherwise degrades measurement reliability over time. The result is a measurable reduction in rework and fewer out-of-tolerance parts during quality inspections, making the changeover a cost-effective maintenance action for production lines and metrology benches.

Reach and stability where it matters

The 105 mm length provides additional reach for recessed features and deep bores while maintaining a stable contact geometry. A Ø 12 mm mounting shank gives a precise fit into the holder, reducing play and ensuring reproducible seating pressure. Compatibility with the caliper series M201.175–M201.178 is specified to simplify selection; technicians benefit from a straightforward replacement that restores original contact geometry without modifications to the instrument.

Workshop-ready durability and straightforward upkeep

The empirically proven hardness of carbide ensures low abrasion under repeated use, which extends service intervals and keeps downtime to a minimum. These replacement tips are a practical maintenance item for metrology equipment used in toolmaking, fixture assembly and machine shops, and they support the reliable transfer of dimensional data during routine inspections. Replacement is performed quickly with basic tooling, enabling calibration cycles to continue with minimal interruption.

Contact Metav Werkzeuge to confirm compatibility with specific calipers and to request ordering advice for Metav IndustryLine carbide replacement tips.

Technical Data

• Article number: M201.175.1
• GTIN: 4061905053610

Facts

• Length: 105 mm
• Shank diameter: Ø 12 mm
• Weight: 0.1 kg

Special features

• Material: carbide
• Compatible with: M201.175–M201.178
• Application: calipers from 500 mm measuring range

FAQ

How do these replacement tips improve measurement repeatability? The carbide composition of the replacement tips increases surface hardness and wear resistance, so the Replacement Tips for Bar-Divider Calipers (M201.175.1) preserve contact geometry and improve repeatability over prolonged use.

Are these tips compatible with my caliper model? Compatibility is specified as M201.175–M201.178; for other models, Metav IndustryLine replacement tips should be checked against the shank diameter and holder design before purchase.

Can these tips be used for internal and external measurements? The contact geometry of the replacement tips supports both internal and external contact tasks commonly encountered on larger calipers in workshop metrology.

Is a special calibration needed after replacing the tips? After mechanical replacement, a quick functional check or calibration is recommended. If formal calibration is required, follow the established calibration procedure applicable to the measuring instrument.

What advantages does the Ø 12 mm shank provide? A Ø 12 mm shank ensures a secure fit in compatible holders, reducing lateral play and improving the stability of the contact point during measurement.

Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com