High wear resistance from HSS‑Co and a compact 10.5 mm diameter combine for accurate slotting in demanding steels and non‑ferrous metals; order the slotting cutter directly via Metav Werkzeuge or ask our consultants if needed MAYKESTAG slotting cutter (10.5 mm) — HSS‑Co, 8 flutes, DIN 850 D The MAYKESTAG slotting cutter is a compact, Type N milling cutter for precision slotting and groove work in steels and short‑chipping non‑ferrous metals HSS‑Co for high heat resistance DIN 850D Type N standard 8 flutes for efficient chip evacuation Cylindrical shank with drive flat Consistent cutting performance for mixed steel and non‑ferrous workpieces The cutter is made from HSS‑Co, a cobalt‑alloyed high‑speed steel that offers improved red hardness and wear resistance compared with conventional HSS. This combination of material and geometry delivers stable cutting when working on construction, case‑hardened and quenched steels, as well as on short‑chipping non‑ferrous metals, reducing the need for frequent regrinding. The DIN 850 D, Type N designation indicates a standardised geometry that balances cutting edge strength and chip control, helping to maintain consistent part quality across production runs. Geometry and flute design that speed up cycle times With 8 flutes, the tool promotes fine chip formation and continuous engagement, which enhances surface finish and reduces vibration in many milling operations. The 10.5 mm diameter and 8 mm cutting length create a compact cutter suited for narrow slots and grooves, while the 6 mm cylindrical shank with drive flat ensures secure clamping in standard toolholders and reduces the risk of slippage under load. Right‑hand cutting direction and the cutter’s flute count are tuned to support steady feed rates and predictable tool life, contributing to improved throughput in repetitive tasks. Practical applications and safe handling in the workshop This slotting cutter is engineered for shops and production lines that require a reliable general‑purpose milling tool for moderate to demanding materials. The Type N geometry and HSS‑Co composition make it resilient during interrupted cuts and occasional contact with harder surfaces, lowering downtime for tool changes. For operators less familiar with milling terminology: “short‑chipping” means the cutter produces small, breakable chips that are easier to evacuate, reducing the risk of chip entanglement and improving surface quality. If clarification is needed about suitability for a specific workpiece or machining strategy, Metav’s technical advisers can provide tailored recommendations. Contact Metav Werkzeuge today for application advice and to secure reliable supply from Emmerich — expert support for selection and fast delivery is available on request Technical data Article number: 4117802224NW Label: Schlitzfräser DIN 850D TypN D.10,5mm HSS‑Co Z.8 L.2,5mm MAYKESTAG Product type: Slotting cutter Manufacturer: ALPEN‑MAYKESTAG GmbH Facts Diameter: 10.5 mm Overall length: 50 mm Cutting length: 8 mm Shank diameter: 6 mm Number of flutes: 8 Cutting direction: Right‑hand cutting Special features Material: HSS‑Co Standard: DIN 850 D · Type N Suited for milling construction, case‑hardened and quenched steels Designed for short‑chipping non‑ferrous metals Cylindrical shank with drive flat FAQ What materials is this cutter suitable for? The MAYKESTAG slotting cutter (SKU 4117802224NW) with HSS‑Co is specified for milling construction steels, case‑hardened and quenched steels, and short‑chipping non‑ferrous metals. How many flutes does the cutter have and what is the benefit? The tool has 8 flutes, which aid efficient chip evacuation and contribute to a finer surface finish during slotting operations. Does the shank type affect clamping? Yes; the 6 mm cylindrical shank with drive flat on this MAYKESTAG cutter improves axial drive and prevents slippage in standard collets and chucks. What does DIN 850 D Type N mean for everyday use? DIN 850 D Type N denotes a standardised cutter geometry that balances edge strength and chip control, offering repeatable performance for general‑purpose milling tasks. Is this cutter suitable for interrupted cuts and tougher materials? The HSS‑Co composition and Type N geometry make the cutter robust for interrupted cuts and increased heat exposure, providing greater durability than standard HSS in such conditions. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Take advantage of the HSS‑Co construction, robust Type N geometry and secure cylinder shank with drive flat for reliable machining of construction and case‑hardened steels; order directly via Metav Werkzeuge or consult our specialists for application advice. MAYKESTAG slot cutter DIN 850 D, HSS‑Co, Ø 10.5 mm, 8 flutes The MAYKESTAG slot cutter is a Type N, DIN 850 D tool designed for precision slotting and small‑scale milling in steels and short‑chipping non‑ferrous metals HSS‑Co material for enhanced heat resistance DIN 850 D, Type N for steel and short‑chipping NE‑metals 8 flutes for improved surface finish Ø 10.5 mm with 8 mm cutting length Cylinder shank with drive flat for secure clamping High‑temperature stability for consistent cuts The use of HSS‑Co (cobalt high‑speed steel) gives the cutter increased red hardness compared with standard high‑speed steel, which means longer life under elevated temperatures in demanding milling operations. This material choice supports consistent dimensional results across series production and reduces the frequency of tool changes. For workshops and production lines, the main benefit is a reduction in downtime and more predictable maintenance intervals when machining structural and case‑hardened steels. Geometry that balances productivity and surface quality Equipped with 8 flutes, the cutter favours a finer finish on the slot walls while maintaining adequate chip formation for short‑chipping materials. The Ø 10.5 mm diameter combined with an 8 mm cutting length is well suited for shallow slotting and finishing passes where tool rigidity and exact diameters matter. In practical terms, the higher flute count supports a smoother feed and can help achieve a better surface without multiple finishing operations, enhancing throughput for batch work. Versatile application across steels and non‑ferrous metals Certified to DIN 850 D as a Type N tool, this slot mill is intended for machining construction steels, case‑hardening and tempered steels as well as short‑chipping non‑ferrous metals. The tool’s right‑hand cutting direction and robust geometry make it a reliable choice for conventional milling setups. When paired with appropriate feeds and speeds for the workpiece, the cutter delivers repeatable slot profiles, making it suitable for component manufacturing and toolroom repairs that demand repeat accuracy. Secure clamping and straightforward handling in the workshop A cylinder shank with drive flat (Mitnahmefläche) and a 6 mm shank diameter provide secure clamping in standard collets and chucks, reducing slippage during interrupted cuts. The overall length of 50 mm keeps the stick‑out modest for improved rigidity, which benefits dimensional control on thin‑walled parts or where chatter must be avoided. For routine maintenance, the cutter’s material and geometry allow predictable resharpening intervals, supporting a cost‑conscious tool management approach in small and medium‑sized workshops. For specialist advice on integrating the MAYKESTAG slot cutter into a production process or to source matching holders and spares, contact Metav Werkzeuge for tailored support and fast supply from Emmerich. Technical data Article number: 4117802223NW Manufacturer: ALPEN‑MAYKESTAG GmbH Product type: Slot cutter Label: Schlitzfräser DIN 850D TypN D.10,5mm HSS‑Co Z.8 L.2mm MAYKESTAG Core specifications Diameter: Ø 10.5 mm Total length: 50 mm Cutting length: 8 mm Flutes: 8 Shank diameter: 6 mm Cutting direction: right‑hand Special features Material: HSS‑Co Standard: DIN 850 D Type: N Shank: cylinder with drive flat Suitable for: construction steels, case‑hardening and tempered steels, short‑chipping non‑ferrous metals FAQ What materials is this cutter suitable for? The MAYKESTAG slot cutter is intended for machining construction steels, case‑hardening and tempered steels and short‑chipping non‑ferrous metals, as specified by its Type N DIN 850 D designation. What are the key dimensions to consider when selecting holders? Ensure compatibility with the 6 mm cylinder shank and a tool stick‑out that keeps the effective length close to the listed 50 mm for optimal rigidity. Can the cutter be resharpened? Yes, the HSS‑Co substrate allows for professional resharpening; adhere to original geometry to maintain cutting performance and the DIN 850 D characteristics. Is the tool suitable for interrupted cuts or slotting in thin parts? The combination of a short 8 mm cutting length and modest stick‑out improves rigidity and makes the cutter suitable for controlled slotting and many interrupted‑cut applications. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Take advantage of a hard-wearing HSS‑Co cutting geometry combined with an 8‑flute configuration and a compact 8 mm cutting length for precise, repeatable slotting in construction and alloy steels — order directly via Metav Werkzeuge or consult the sales team for application advice. MAYKESTAG Slot Milling Cutter DIN 850D Type N — 10.5 mm, HSS‑Co The MAYKESTAG Slot Milling Cutter DIN 850D Type N is a right‑hand slotting cutter designed for machining construction, case‑hardened and quenched‑and‑tempered steels, plus short‑chipping non‑ferrous metals in workshop and production environments *HSS‑Co construction for higher heat resistance *8 cutting edges for smooth slotting *Right‑hand cutting for conventional milling *10.5 mm diameter, 8 mm cutting length High‑accuracy slotting for demanding steels and alloys The alloyed HSS‑Co substrate specified for this cutter is selected to balance wear resistance and toughness when machining medium‑hard and heat‑resistant workpiece materials. Meeting the DIN 850D design intent, the tool’s 8 flutes create a stable cutting geometry that reduces vibration and improves dimensional repeatability during slotting operations. For production lines and jobbing shops alike, this results in fewer rework cycles and more consistent part tolerances. Reliable chip control and process stability A short 8 mm cutting length together with the right‑hand helix favours machining of short‑chipping materials and reduces the risk of built‑up edge. The multi‑flute layout helps distribute cutting forces, enabling finer feed per tooth at equivalent material removal rates; this supports higher surface quality and lengthens the service life of the tool. In practice, these characteristics translate to lower downtime and predictable tool change intervals in both single‑piece and small‑batch series work. Practical integration into existing toolholding systems The cutter is supplied with a 6 mm cylindrical shank with a drive flat, permitting secure clamping in standard collets and holders while maintaining concentricity for precision slotting. The overall length of 50 mm and a 10.5 mm nominal diameter make the tool compatible with compact set‑ups and machines where reach and rigidity are critical. This straightforward fitment simplifies inventory management and reduces the need for specialised toolholders. Discuss specific applications and material pairings with Metav Werkzeuge — call +49 2822 7131930 or eMail info@metav-werkzeuge.com to confirm suitability for the intended machining task Technical data Article number: 4117802225NW Label: Schlitzfräser DIN 850D TypN D.10,5mm HSS‑Co Z.8 L.3mm MAYKESTAG Manufacturer: ALPEN‑MAYKESTAG GmbH Facts Diameter: 10.5 mm Cutting length: 8 mm Overall length: 50 mm Number of cutting edges: 8 Shank diameter: 6 mm Cutting direction: right‑hand Special features Material: HSS‑Co Norm: DIN 850D Type: N Cylindrical shank with drive flat Suited for construction, case‑hardened and tempered steels Suitable for short‑chipping non‑ferrous metals FAQ What materials is this slot milling cutter suitable for? The MAYKESTAG slot milling cutter (DIN 850D Type N, SKU 4117802225NW) is intended for construction steels, case‑hardened and quenched‑and‑tempered steels, and for short‑chipping non‑ferrous metals where an HSS‑Co substrate is advantageous. How does the 8‑flute design affect machining? An 8‑flute geometry on this cutter increases contact stability and distributes cutting forces, enabling finer feeds per tooth and improved surface finish when using the MAYKESTAG slot milling cutter in appropriate setups. Which toolholders fit the cutter’s shank? The 6 mm cylindrical shank with drive flat is compatible with standard collet chucks and small‑diameter holders commonly used in milling machines and machining centres for precise clamping of the MAYKESTAG slot milling cutter. Is this cutter suitable for high‑speed milling? The cutter’s HSS‑Co composition offers a balance of toughness and heat resistance; however, spindle speed and feed must be set according to the machined material and machine rigidity when using the MAYKESTAG DIN 850D tool. How many cutting edges are on this tool and what is the practical benefit? The tool has 8 cutting edges, which promote smoother slotting operations, greater surface integrity and improved tool life compared with lower‑flute variants when matched to the right workpiece and cutting parameters. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Take advantage of a durable HSS‑Co construction and an optimised 8‑flute geometry for reliable slotting in demanding materials; the DIN 850 D compliance and a cylindrical shank with drive flat ensure secure clamping and repeatable results. Order the cutter directly via Metav Werkzeuge or request consultation from their technical advisors if further machining data is required. MAYKESTAG Slot milling cutter DIN 850 D, Ø13.5 mm, HSS‑Co The MAYKESTAG slot milling cutter DIN 850 D is a right‑hand, 8‑flute tool designed for precise slotting in construction, case‑hardened and quenched‑and‑tempered steels as well as short‑chipping non‑ferrous metals HSS‑Co for high wear resistance 8 flutes for improved surface finish DIN 850 D standardised geometry Cylindrical shank with drive flat for secure clamping High cutting performance with cobalt high‑speed steel The cutter is manufactured from HSS‑Co, a cobalt‑alloyed high‑speed steel that combines toughness with elevated hot‑hardness, which reduces flank wear during medium‑duty milling operations. With a Ø13.5 mm diameter and a cutting length 8 mm, the tool is intended for short slotting tasks where consistent chip control matters. The 8‑flute design increases cutting engagement and distributes cutting forces across more edges, resulting in a smoother surface finish and longer indexable life compared with fewer‑tooth counterparts. This technical combination supports efficient machining cycles and helps maintain dimensional accuracy in repeated production runs. Designed for demanding steels and short‑chipping non‑ferrous metals Norm conformity to DIN 850 D and the choice of HSS‑Co make this cutter suitable for machining construction steels, case‑hardened parts and quenched‑and‑tempered steels, while still coping well with short‑chipping non‑ferrous metals. The tool’s right‑hand cut and the cylindrical shank with a drive flat ensure reliable torque transmission and secure clamping in conventional and automated toolholders. With a shank Ø10 mm and an overall length 56 mm, the cutter integrates smoothly into standard collets and chucks, enabling a compact set‑up that keeps runout low and repeatability high. Operational benefits for workshop and production environments Supplied as a single unit, the cutter’s compact cutting length 8 mm and robust material selection reduce the need for frequent regrinding in short‑run series, while the standardised geometry simplifies tool management across multiple machines. The combination of DIN conformity, a solid HSS‑Co body and an optimised flute count supports predictable tool life and stable chip evacuation, which in turn lowers downtime and increases throughput. For applications requiring precise slot widths and consistent edge quality, this tool delivers measurable improvements in process reliability and reproducibility. For process‑critical slotting, contact Metav Werkzeuge for tailored advice or to source the MAYKESTAG slot milling cutter directly—email info@metav-werkzeuge.com or call +49 2822 7131930 to discuss specifications and availability Technical data Article number: 4117802226NW SKU / UID: 4117802226NW Manufacturer: ALPEN‑MAYKESTAG GmbH Product type: Slot milling cutter Facts Diameter: Ø13.5 mm Overall length: 56 mm Cutting length: 8 mm Shank diameter: Ø10 mm Number of flutes: 8 Packaging unit: 1 Special features Material: HSS‑Co Standard: DIN 850 D Cut direction: right‑hand cut Cylindrical shank with drive flat Application: construction steels, case‑hardened and quenched‑and‑tempered steels, short‑chipping non‑ferrous metals No coating specified FAQ What materials is this slot milling cutter suitable for? The MAYKESTAG slot milling cutter, made from HSS‑Co, is suitable for construction steels, case‑hardened parts and quenched‑and‑tempered steels, and it also performs well with short‑chipping non‑ferrous metals. How many flutes does the cutter have and what is the benefit? This tool features 8 flutes; the increased number of cutting edges improves surface finish and reduces individual edge loading for steadier tool life. What shank size and overall length should be expected? The cutter has a shank diameter of 10 mm and an overall length of 56 mm, dimensions that support secure clamping and compatibility with standard toolholding systems. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Combine HSS‑Co tool steel, DIN 850 D Type N geometry and a 10 mm cylindrical shank with drive face for robust, precise slotting in mixed workshop and production environments; order directly via Metav Werkzeuge or request further advice from our consultants. MAYKESTAG slot milling cutter — 13.5 mm, HSS‑Co, 8‑tooth The MAYKESTAG slot milling cutter is a right‑hand, DIN 850 D Type N cutter designed for slotting and peripheral milling of structural, case‑hardened and tempered steels as well as short‑chip non‑ferrous metals HSS‑Co for enhanced wear resistance DIN 850 D Type N for reliable chip control 8 mm cutting length for precise slot depth 10 mm cylindrical shank with drive face Long‑lasting cutting performance for production use The HSS‑Co composition combines high‑speed steel with cobalt alloying to deliver improved hot‑hardness and wear resistance compared with standard HSS. This makes the cutter suitable for repeated engagement under load, extending tool life in continuous operation. With eight cutting edges, the design balances material removal and surface finish; the geometry specified by DIN 850 D supports consistent chip formation, reducing rebating and providing predictable tool behaviour in automated or manual setups. Precise slotting in mixed materials with controlled chip breakage The tool is specified as Type N, optimised for slotting and plunge cuts where short, controllable chips are required. The modest 8 mm cutting length and 13.5 mm diameter permit accurate slot depths while limiting tool overhang, which helps maintain concentricity and surface quality. Right‑hand cutting and the flute geometry are chosen to favour short‑chip performance, making the cutter suitable for structural steels, quenched and tempered components, and short‑chip non‑ferrous alloys in light‑to‑medium machining tasks. Secure mounting and straightforward integration into tooling systems A 10 mm cylindrical shank with drive face provides a stable interface with collets and toolholders, improving torque transmission and reducing slippage during interrupted cuts. The compact 56 mm overall length minimises cantilevering, and the standardised shank diameter facilitates quick tool changes on common milling spindles. Specified tolerances and familiar mounting dimensions enable seamless integration into production tooling arrays and retrofit replacement stocks. Operational advantage and application clarity Chosen for balanced performance rather than extreme removal rates, this slotting cutter offers predictable behaviour in finishing and semi‑finishing operations. The combination of HSS‑Co material and the DIN‑compliant flute profile results in improved run‑time and consistent surface outcomes, helping to reduce downtime for tool changes. For shops handling mixed batches of steel and short‑chip non‑ferrous components, the cutter represents a pragmatic compromise between economy and machining stability. For dependable slotting and consistent supply, request the MAYKESTAG HSS‑Co slot milling cutter via Metav Werkzeuge — our Emmerich hub provides expert advice and reliable delivery to support production continuity Technical data Article number: 4117802227NW Manufacturer: ALPEN‑MAYKESTAG GmbH Product type: Slot milling cutter SKU: 4117802227NW Facts Diameter: 13.5 mm Cutting length: 8 mm Overall length: 56 mm Shank diameter: 10 mm Number of cutting edges: 8 Special features Material: HSS‑Co Norm: DIN 850 D Type: N (short‑chip geometry) Cutting direction: right‑hand cutting Shank: cylindrical shank with drive face Intended for: structural, case‑hardened and tempered steels; short‑chip non‑ferrous metals FAQ What materials is this slotting cutter suited to? The MAYKESTAG slot milling cutter is specified for structural steels, case‑hardened and tempered steels and short‑chip non‑ferrous metals, thanks to its HSS‑Co composition and Type N geometry. What are the key dimensions for mounting and setup? The cutter features a 10 mm cylindrical shank with drive face and a 56 mm overall length; these dimensions suit common collets and holders and are identified under SKU 4117802227NW. How deep can the cutter machine in a single pass? The tool offers an 8 mm cutting length for controlled slot depths; for deeper slots, multiple passes with careful machining parameters are recommended. Does the cutter meet an industry standard for geometry? Yes, the flute and cutting geometry comply with DIN 850 D and the Type N designation, which supports short‑chip performance and predictable chip control. Manufacturer: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Take advantage of a high-performance combination: HSS‑Co construction for elevated heat resistance, an 8-flute geometry for fine surface quality, and a compact cutting length for precise slotting operations—available through Metav Werkzeuge or via consultation with our technical team. MAYKESTAG Slot cutter DIN 850 D, Type N – Ø16.5 mm, HSS‑Co, 8 flutes The MAYKESTAG Slot cutter DIN 850 D Type N is a precision slotting tool designed for machining construction, case-hardened and quenched steels, as well as short‑chipping non‑ferrous materials in workshop and production settings Cobalt HSS for enhanced heat resistance 8 flutes for smooth surface finish Ø16.5 mm cutting diameter Cylinder shank with drive flat for secure clamping Consistent finish and productivity for series and single-part work The tool’s cobalt high-speed steel (HSS‑Co) composition provides improved hot hardness compared with standard high-speed steels, which enhances tool life under elevated temperatures. Combined with the 8 flutes, this geometry reduces vibration and produces a refined surface, making the cutter particularly suitable for operations that demand repeatable surface quality. The result is a reliable tool for both small batch production and individual precision tasks. Compact design for controlled slotting and secure clamping With an overall length of 56 mm and an 8 mm cutting length, the cutter is optimised for shallow slotting and finishing passes where rigidity matters. The 10 mm shank and cylinder shank with drive flat ensure secure clamping in standard collets and holders, lowering the risk of slippage and runout during machining. The right‑hand cutting direction conforms with standard milling spindle rotation, simplifying setup and reducing process variables. Application range explained for reliable selection Certified to DIN 850 D and specified as Type N, the cutter is intended for slotting tasks in construction and case-hardened steels as well as for short‑chipping non‑ferrous metals. "Short‑chipping" refers to materials that break into short, manageable chips rather than long strings; this cutter’s flute design supports efficient chip evacuation in such materials. For customers evaluating tool selection, these characteristics translate directly into fewer tool changes and lower production interruptions. Process advantages and practical handling notes The combination of HSS‑Co and multiple flutes balances wear resistance and surface performance, offering a cost-efficient alternative to more exotic materials where extreme temperatures or very high cutting speeds are not required. The Ø16.5 mm diameter provides a stable cutting cross-section, while the modest cutting length reduces deflection in narrow slotting operations. For best results, secure the cutter in an appropriate 10 mm holder and select feeds and speeds matching short‑chip materials and the stated tool material. For precision slotting tasks, consult Metav Werkzeuge’s specialists to confirm suitability for the intended materials and to order this MAYKESTAG slot cutter directly; technical enquiries are welcome at info@metav-werkzeuge.com or by telephone on +49 2822 7131930 Technical data Article number: 4117802230NW Label: Schlitzfräser DIN 850D Typ N D.16,5mm HSS-Co Z.8 L.5mm MAYKESTAG Manufacturer: ALPEN-MAYKESTAG GmbH Facts Diameter: 16.5 mm Total length: 56 mm Cutting length: 8 mm Shank diameter: 10 mm Number of flutes: 8 SKU / UID: 4117802230NW Special features Material: HSS‑Co Norm: DIN 850 D Type: N Cutting direction: right-hand cutting Cylinder shank with drive flat Suitable for machining construction, case-hardened and quenched steels and for short‑chipping non‑ferrous metals FAQ What materials is this slot cutter suitable for? The MAYKESTAG slot cutter DIN 850 D Type N (4117802230NW) is designed for construction, case-hardened and quenched steels, and for short‑chipping non‑ferrous metals owing to its HSS‑Co composition and flute geometry. How should the cutter be clamped for best results? Use a tool holder or collet compatible with a 10 mm shank and ensure the cylinder shank with drive flat is aligned to prevent rotation; this improves runout and machining stability with the MAYKESTAG slot cutter. What performance benefits do the 8 flutes provide? The 8 flutes reduce vibration and enhance surface finish in slotting operations, supporting a more consistent machining result and extended tool life compared with lower‑flute configurations for similar applications. Is this cutter compliant with a standard specification? Yes—the cutter is specified to DIN 850 D, Type N, which describes the geometry and intended use for this class of slot cutters. Manufacturer: ALPEN-MAYKESTAG GmbH; Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Take advantage of the combination of HSS‑Co toughness, a Ø16.5 mm cutting diameter and a 10 mm shank for reliable slotting in mixed-steel workshops; order the slot milling cutter directly via Metav Werkzeuge or ask our consultants if needed. MAYKESTAG Slot Milling Cutter — Ø16.5 mm, HSS‑Co, 8 flutes The MAYKESTAG slot milling cutter is a right‑hand slot cutter for precision machining of construction and tempered steels, as well as short‑chipping non‑ferrous metals, supplied on a cylindrical shank with drive flat HSS‑Co grade for hard‑wearing performance Ø16.5 mm diameter for precise slotting 8 cutting edges for smooth chip formation 10 mm shank with drive flat for secure clamping High‑temperature stability and durable cutting life Manufactured from HSS‑Co, the tool is designed to maintain hardness and cutting geometry at elevated temperatures, which extends tool life during continuous milling. The combination of a DIN 850 D geometry and 8 flutes supports even load distribution across the cutting edges; this reduces wear and improves dimensional stability in repetitive production runs. The cutting length 8 mm and Ø16.5 mm diameter are set to deliver consistent slot widths while keeping vibrations low, enabling predictable cycle times in CNC and manual milling operations. Concentric clamping and process reliability A 10 mm shank with a dedicated drive flat ensures secure clamping and repeatable concentricity when used in standard collets or chucks. The cylindrical shank design minimises runout, which directly improves surface finish and reduces the need for secondary rework. Where tight tolerances are required, the stable interface between tool and spindle results in reduced scrap rates and more predictable setup times, benefitting batch production and single‑part tasks alike. Proven application range and chip control Specified for machining construction steels, tempered steels and short‑chipping non‑ferrous metals, the cutter’s geometry favours controlled chip breakage and evacuation. Right‑hand cutting orientation provides conventional feed behaviour for standard milling fixtures, and the flute geometry is optimised for short, brittle chips rather than long, stringy swarf. This reduces the risk of chip re‑cutting and supports safer, cleaner operation on lathes and milling centres when slotting or plunge milling small features. Workshop efficiency, standard conformity and handling Compliance with DIN 850 D guarantees a standardised profile and interchangeability, which simplifies tool management across shops using compatible tooling systems. The solid‑carbide‑alternative design is not used here; instead this robust HSS‑Co cutter offers an economical balance between cutting performance and cost‑effective regrinding cycles. Packaging is supplied per item for direct replacement, and the reliable geometry supports reproducible results, improving throughput and trust in daily production planning. Metav Werkzeuge’s quality‑filter approach ensures consistent delivery and product traceability. For procurement of robust slot milling performance, contact Metav Werkzeuge for tailored advice and to secure the MAYKESTAG slot milling cutter (SKU 4117802229NW) via info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: 4117802229NW Description: Schlitzfräser DIN 850D Typ N D.16,5mm HSS‑Co Z.8 L.4mm MAYKESTAG Manufacturer: ALPEN‑MAYKESTAG GmbH Product type: Slot milling cutter Facts Diameter: 16.5 mm Overall length: 56 mm Cutting length: 8 mm Number of cutting edges: 8 Shank diameter: 10 mm Packaging unit: 1 SKU / UID: 4117802229NW Special features Material: HSS‑Co Norm / Type: DIN 850 D · Type N Cutting direction: right‑hand cutting Shank: cylindrical shank with drive flat Application: for machining construction, case‑hardened and tempered steels and for short‑chipping non‑ferrous metals FAQ What materials is this slot milling cutter suitable for? The slot milling cutter from MAYKESTAG is intended for construction steels, tempered steels and short‑chipping non‑ferrous metals, as stated in the technical specifications. How should the tool be clamped for best results? Use a standard collet or chuck sized for the 10 mm shank; the cylindrical shank with drive flat ensures secure clamping and reduced runout when clamped correctly. Can this cutter be used in high‑speed milling applications? The HSS‑Co grade provides improved heat resistance compared with standard high‑speed steel, making the cutter suitable for moderately elevated cutting speeds within recommended machining parameters. What standard does the tool comply with? The geometry adheres to DIN 850 D (Type N), which ensures consistent profile and interchangeability across compliant tooling systems. How many cutting edges does the tool have and what benefit does this offer? The cutter features 8 flutes, which provide smoother chip load distribution and improved surface finish in slotting operations. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Take advantage of the combination of HSS‑Co construction, an 8‑flute geometry and a secure 10 mm shank for consistent slotting performance in demanding workshop environments; order the cutter directly via Metav Werkzeuge or consult our experts for application advice. Slot milling cutter DIN 850 D Type N, Ø 16.5 mm, HSS‑Co – ALPEN‑MAYKESTAG A Slot milling cutter DIN 850 D Type N designed for slotting and face milling of construction, case‑hardened and quenched steels as well as short‑chipping non‑ferrous metals HSS‑Co material for high heat resistance DIN 850 D Type N cutting geometry 8 flutes for efficient chip evacuation Shank Ø 10 mm with drive flat Consistent cutting performance in demanding steels Manufactured from HSS‑Co, the cutter offers increased red‑hardness and wear resistance compared with standard high‑speed steel, which benefits operations on tougher workpiece materials. The DIN 850 D / Type N geometry combines a robust cutter body with stable flute profiles to reduce chatter and extend tool life. This results in reliably repeatable cuts when machining construction and quenched steels, supporting stable production throughput and predictable tool intervals. Fast chip removal and improved surface quality The 8 flutes are arranged to balance cutting forces and promote continuous chip evacuation, particularly effective within the cutter’s cutting length 8 mm. A compact diameter of Ø 16.5 mm reduces deflection in slotting tasks while maintaining rigidity, which helps to achieve a smoother surface finish and tighter dimensional control. For short‑chipping non‑ferrous metals, this flute count and geometry suppress built‑up edge formation and support higher feed rates where the process allows. Secure clamping and workshop compatibility The cylindrical shank with a drive flat and a shank Ø 10 mm enables reliable clamping in standard holders and collets, simplifying tool changes in busy shops. An overall length of 56 mm keeps the projection low, reducing vibration and improving concentricity under load. The cutter is right‑hand cutting, suitable for conventional milling set‑ups. Together these mechanical features make the tool straightforward to integrate into existing tool magazines and manual fixtures without special adaptations. Contact Metav Werkzeuge today for tailored application advice on the ALPEN‑MAYKESTAG slot milling cutter and to discuss suitable holders or cutting parameters – eMail info@metav-werkzeuge.com or call +49 2822 7131930 Technical Data Article number: 4117802228NW Manufacturer: ALPEN‑MAYKESTAG GmbH Product type: Slot milling cutter (Type N) SKU / UID: 4117802228NW Key dimensions Diameter: 16.5 mm Cutting length: 8 mm Overall length: 56 mm Shank diameter: 10 mm Number of flutes: 8 Material & features Material: HSS‑Co (cobalt high‑speed steel) Cutting direction: right‑hand cutting Standard / type: DIN 850 D, Type N Shank: cylindrical with drive flat Suitable for: construction, case‑hardened and quenched steels; short‑chipping non‑ferrous metals FAQ What materials can be machined with this slot milling cutter? The ALPEN‑MAYKESTAG slot milling cutter (SKU 4117802228NW) is intended for machining construction steels, case‑hardened and quenched steels, and short‑chipping non‑ferrous metals, thanks to its HSS‑Co composition and Type N geometry. Is the shank compatible with standard collets? Yes; the tool has a shank Ø 10 mm and a cylindrical shank with drive flat, ensuring secure clamping in common 10 mm collets and chucks used in general workshop tooling. Is this cutter suitable for finishing passes? The combination of 8 flutes and a compact diameter (Ø 16.5 mm) supports good surface quality in slotting and light finishing operations, provided cutting parameters are adjusted for material and machine rigidity. How should the cutter be clamped to avoid run‑out? Use a precision collet or shrink fit holder for the shank Ø 10 mm and ensure minimal tool projection to benefit from the cutter’s overall length 56 mm and reduced tendency to vibrate during cutting. Which cutting direction does the tool use? The tool is right‑hand cutting, compatible with standard clockwise spindle rotation used in most milling operations. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Benefit from precise, durable cutting performance and secure clamping: the combination of HSS‑Co cutting material, a 19.5 mm diameter and a cylindrical shank with drive flat delivers consistent slotting results and long tool life. Order the cutter via Metav Werkzeuge or consult our technical team for application-specific advice. MAYKESTAG Slot milling cutter DIN 850 D, HSS‑Co, D 19.5 mm MAYKESTAG Slot milling cutter DIN 850 D Type N for slotting in construction, application and quenched‑and‑tempered steels as well as short‑chipping non‑ferrous metals HSS‑Co base material for high hot hardness DIN 850 D standard, Type N geometry 10 cutting edges for fine surface finish 10 mm shank with drive flat for secure clamping High‑performance cutter material for demanding steels The use of HSS‑Co (cobalt high‑speed steel) ensures elevated hot hardness and thermal resistance compared with standard high‑speed steels, making this slotting tool suitable for machining construction and tempered steels. With a 19.5 mm diameter and a 10 mm cutting length, the geometry is geared towards precise slot creation while maintaining tool rigidity. The material choice reduces the risk of premature wear when intermittent temperatures rise, so process reliability increases and downtime decreases. Geometry and fluting designed for productivity and surface quality A Type N geometry under DIN 850 D provides a balanced profile for general slotting duties, and the presence of 10 cutting edges supports higher feed rates with finer stepovers, resulting in improved component finish. The right‑hand cut orientation matches standard spindle directions and machining cycles. Because more cutting edges distribute the load, the tool can offer a steady removal rate with less vibration, translating into repeatable tolerances and fewer rework cycles for medium‑duty production. Secure clamping and compatibility with workshop toolholders The 10 mm shank with drive flat provides positive location in standard collets and chucks, reducing slippage and improving torque transfer at higher feeds. The overall length of 63 mm affords sufficient reach for common slotting depths while keeping overhang minimal to help preserve run‑out accuracy. The cylindrical shank format is compatible with a broad range of holder systems, simplifying tool changeover and inventory management across the machine park. Practical benefits for shopfloor workflows Using a dedicated slot milling cutter made from HSS‑Co for short‑chipping non‑ferrous metals as well as steels reduces the need for multiple tool families, helping to streamline tooling lists and operating procedures. The tool’s conformity to DIN 850 D means predictable performance within standardised setups, easing programming and quality control. Combined with Metav’s supply chain reliability, the cutter supports continuous production planning and predictable lead times. For application guidance or to secure supply of the MAYKESTAG slot milling cutter, contact Metav Werkzeuge today for technical consultation and swift delivery — eMail info@metav-werkzeuge.com or phone +49 2822 7131930 for tailored recommendations. Technical data Article number: 4117802232NW Product type: Slot milling cutter Manufacturer: ALPEN‑MAYKESTAG GmbH Material: HSS‑Co SKU: 4117802232NW Facts Diameter: 19.5 mm Overall length: 63 mm Cutting length: 10 mm Shank diameter: 10 mm Number of cutting edges: 10 Cutting direction: right‑hand cut Special features DIN 850 D Type N geometry Cylindrical shank with drive flat Suitable for construction, application and quenched‑and‑tempered steels Suitable for short‑chipping non‑ferrous metals FAQ What materials is this slot milling cutter suitable for? The MAYKESTAG slot milling cutter (ALPEN‑MAYKESTAG GmbH, SKU 4117802232NW) is specified for construction and quenched‑and‑tempered steels and for short‑chipping non‑ferrous metals, reflecting its HSS‑Co composition and Type N geometry. How does the number of cutting edges affect machining? With 10 cutting edges, the cutter distributes cutting forces over more teeth, improving surface finish and allowing higher feed per revolution for applicable materials when using appropriate cutting parameters with the MAYKESTAG tool. Is the shank compatible with common collets and chucks? Yes, the cutter has a 10 mm cylindrical shank with a drive flat to ensure secure clamping in standard collets and toolholders; this reduces slippage during slotting operations. What does DIN 850 D Type N imply for users? The DIN 850 D Type N designation denotes a standardised slotting geometry suitable for general slotting applications, offering predictable cutting behaviour and easier process integration. Does the tool cut left‑hand or right‑hand? The tool is right‑hand cutting, matching the typical clockwise spindle rotation of most machining centres and mills. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Take advantage of a robust HSS‑Co construction combined with a DIN 850 D Type N geometry and 10 cutting edges to achieve consistent slotting results in mixed workshop environments; order the cutter directly via Metav Werkzeuge or request specialist advice from our consultants. MAYKESTAG slot cutter DIN 850 D Type N, Ø19.5 mm — HSS‑Co, 10 flutes MAYKESTAG slot cutter DIN 850 D Type N designed for precise slotting tasks in construction and quenched-and-tempered steels as well as short-chip non-ferrous metals HSS‑Co grade for extended tool life DIN 850 D, Type N geometry 10 cutting edges for efficient stock removal Cylindrical shank with drive flat, Ø10 mm High-efficiency cutting backed by tool-grade material The combination of HSS‑Co construction and a multi‑edge design delivers reliable performance for demanding slotting. The hardened high-speed alloy provides improved wear resistance compared with standard high-speed steels, while the 10 cutting edges reduce chip load per tooth and promote smooth material evacuation. For production-oriented machining, this configuration means more consistent surface quality and longer intervals between regrinds, which in turn helps to maintain process stability and productivity. Application range and material compatibility for process planning Designed in accordance with DIN 850 D Type N, the cutter is suited to machining construction, case‑hardened and quenched‑and‑tempered steels as well as short‑chip non‑ferrous metals. The Type N geometry balances cutting forces and chip control, which is advantageous when working with mixed batches or when frequent tool changes are costly. This specification enables planners to select a single tool for a range of alloys, simplifying tool inventories and reducing setup complexity. Accurate clamping and reliable tool engagement at the spindle The cylindrical shank with a drive flat and a Ø10 mm shank enables secure clamping in standard collets and chucks, reducing runout and vibration during slotting operations. The cutter’s Ø19.5 mm diameter and a cutting length of 10 mm are matched to a compact overall length, allowing efficient access in constrained setups while maintaining stiffness. Together, these features support repeatable slot profiles and minimise the risk of chatter in medium‑duty milling applications. Practical benefits for workshop and industrial workflows Right‑hand cutting and the compact profile allow straightforward integration into existing machining cycles without elaborate programme changes. Fewer tool interventions and predictable edge life contribute to lower downtime and easier capacity planning. For workshops aiming to democratise precision, this cutter offers a practical combination of durability, process reliability, and compatibility with standard toolholders — qualities that support steady output and help meet delivery commitments. For reliable slotting performance with HSS‑Co durability, contact Metav Werkzeuge to secure the MAYKESTAG slot cutter and discuss delivery options or technical recommendations tailored to specific materials and machine setups. Technical data Article number: 4117802233NW Label: Schlitzfräser DIN 850D Typ N D.19,5mm HSS-Co Z.10 L.6mm MAYKESTAG Manufacturer: ALPEN-MAYKESTAG GmbH Product type: Slot cutter Core specifications Diameter: 19.5 mm Cutting length: 10 mm Overall length: 63 mm Shank diameter: 10 mm Cutting edges: 10 Cutting direction: Right-hand Materials & special features Material: HSS-Co Standard: DIN 850 D, Type N Intended for construction and quenched-and-tempered steels Suitable for short-chip non‑ferrous metals Cylindrical shank with drive flat FAQ Which materials is the slot cutter suitable for? The slot cutter is specified for machining construction steels, quenched‑and‑tempered steels and short‑chip non‑ferrous metals according to the DIN 850 D Type N designation. What is the shank size and how should it be clamped? The tool has a Ø10 mm cylindrical shank with a drive flat; clamp in a matched collet or chuck to reduce runout and ensure secure engagement. How many cutting edges does the cutter have and what is the benefit? With 10 cutting edges, the cutter reduces chip load per tooth for smoother cutting action and improved surface finish during slotting. Is a coating specified for the tool? No coating is listed for this tool; the base material is HSS‑Co, chosen for its wear resistance without an additional surface finish. What is the article number for ordering or reference? The article number is 4117802233NW; this identifies the MAYKESTAG slot cutter (HSS‑Co, DIN 850 D Type N) for procurement and stock control. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Take advantage of a robust combination of HSS‑Co performance and DIN 850 D Type N conformity for reliable slotting in short‑chipping non‑ferrous metals and a broad range of steels; the cylindrical shank with drive flat ensures secure toolholding. Order the Slot cutter DIN 850 D Type N, Ø 19.5 mm, HSS‑Co, 10 flutes directly via Metav Werkzeuge or ask our consultants if needed. Slot cutter DIN 850 D Type N, Ø 19.5 mm — HSS‑Co, 10 flutes by MAYKESTAG The Slot cutter DIN 850 D Type N is a right‑hand cutting milling tool designed for precision slotting and profile machining in engineering workshops and production environments. HSS‑Co high‑performance cutting steel DIN 850 D Type N standard conformity Cylindrical shank with drive flat Suited to steels and short‑chipping non‑ferrous metals Increased material removal with consistent chip control The milling tool combines a HSS‑Co cutting material with a dense tooth count to deliver steady removal rates and reliable chip formation. With a diameter of Ø 19.5 mm and 10 flutes, the cutter is configured to maintain a uniform engagement in the workpiece and to reduce vibration during slotting operations. The right‑hand cut specification supports conventional tool paths and is compatible with common CNC and manual milling setups. The result is higher process stability and fewer rejects when working on components that demand repeatable groove quality. Durable alloy and standardised geometry for long service life Manufactured to DIN 850 D, the cutter uses a cobalt‑alloyed high‑speed steel that improves heat resistance and retains hardness under elevated cutting temperatures. The cobalt alloy content increases wear resistance and contributes to longer tool life compared with standard HSS grades. The cylindrical shank with drive flat provides positive torque transmission and simplifies clamping in collets or end mill holders, reducing slippage and machine downtime. For users unfamiliar with the terminology: DIN 850 D denotes a standardised slotting geometry and tolerance band, ensuring interchangeability and predictable cutting behaviour. Application range and handling benefits for production workflows The tool is intended for machining construction steels, case‑hardened steels and short‑chipping non‑ferrous metals, offering versatility across maintenance, prototyping and series production. Thanks to the compact overall length and the robust shank diameter, the cutter minimises chatter and supports fine‑tolerance slotting and keyed features. Where high precision is required, the tool’s geometry yields clean slot walls and consistent profile dimensions, helping to reduce finishing operations. The MAYKESTAG design focus on repeatability and stable chip evacuation enhances throughput and supports tighter process windows. For reliable slotting performance with an emphasis on HSS‑Co durability, contact Metav Werkzeuge to request technical advice or place an order for the MAYKESTAG slot cutter — experts at Metav Werkzeuge will advise on toolholders and suitable machining parameters Technical data Article number: 4117802231NW Label: Schlitzfräser DIN 850D TypN D.19,5mm HSS-Co Z.10 L.4mm MAYKESTAG Manufacturer: ALPEN-MAYKESTAG GmbH Specifications Diameter: 19.5 mm Total length: 63 mm Shank diameter: 10 mm Number of cutting edges: 10 Features Material: HSS‑Co Cutting direction: Right‑hand cut Shank: Cylindrical shank with drive flat Standard: DIN 850 D Type: N SKU / UID: 4117802231NW FAQ What materials is this slot cutter suitable for? The Slot cutter DIN 850 D Type N is suitable for construction steels, case‑hardened steels and short‑chipping non‑ferrous metals, using the HSS‑Co grade to withstand elevated cutting temperatures. Does the shank fit standard collets and holders? The cylindrical shank with drive flat is designed for secure clamping in standard collets and end mill holders; the 10 mm shank diameter matches commonly used toolholding systems. How does HSS‑Co compare to standard HSS for this application? HSS‑Co (cobalt‑alloyed high‑speed steel) offers improved heat resistance and wear performance over standard HSS, extending tool life under intermittent high‑load conditions typical for slotting. Is this cutter suitable for high‑speed machining? The cutter’s geometry and DIN 850 D standard make it appropriate for controlled spindle speeds; recommended cutting parameters depend on the specific material and machine rigidity. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Take advantage of a robust combination of HSS‑Co cutting material, DIN 850 D Type N standardisation and a compact geometry for consistent slotting results; order directly via Metav Werkzeuge or consult our specialists for application advice. MAYKESTAG slot cutter DIN 850 D, Ø 22.5 mm, HSS‑Co, 10 teeth The MAYKESTAG slot cutter DIN 850 D is a high‑performance milling cutter for slotting and finishing work in construction and quenched steels as well as short‑chipping non‑ferrous metals. HSS‑Co cutting material for high wear resistance DIN 850 D Type N for standardised performance 10 cutting edges for efficient material removal Reliable material and standard for longer service life The cutter is manufactured from HSS‑Co (cobalt high‑speed steel), a material known for its elevated hot hardness and wear resistance, which supports more sustained productivity under thermal load. Compliance with DIN 850 D and classification as Type N ensures consistent geometry and cutting behaviour across batches, simplifying tool selection and process planning. These attributes translate into reduced tool changes and predictable tool life for workshops that demand steady throughput. Efficient chip evacuation and cutting action for mixed applications Equipped with 10 cutting edges and a right‑hand cutting spiral, the tool delivers controlled chip formation and smooth engagement when machining construction and quenched steels as well as short‑chipping non‑ferrous metals. The increased flute count favours smaller chip cross‑sections and higher feed rates where machine power permits, enabling faster material removal without sacrificing surface finish. The cutter’s configuration reduces the risk of built‑up edge in sticky alloys and supports stable chip control in intermittent cuts. Compact dimensions for versatile integration in the workshop With an Ø 22.5 mm cutting diameter, a total length of 63 mm and a cutting length of 10 mm on a 10 mm shank, the tool fits a wide range of standard milling holders and collet chucks. The cylindrical shank with drive flat provides secure clamping and repeatable concentricity, which contributes to consistent slot width and runout behaviour. These precise dimensions help streamline tool inventory and make the cutter a practical choice for jobbing shops and production cells alike. For tailored guidance on selecting the right MAYKESTAG slot cutter or to arrange fast delivery from Metav Werkzeuge, contact our specialists at Metav Werkzeuge GmbH in Emmerich via info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: 4117802234NW Product label: Schlitzfräser DIN 850D Typ N, Ø 22.5 mm, HSS‑Co, Z=10, Lc 10 mm Manufacturer: ALPEN‑MAYKESTAG GmbH Core specifications Diameter: 22.5 mm Overall length: 63 mm Cutting length: 10 mm Shank diameter: 10 mm Number of cutting edges: 10 Cutting direction: right‑hand Special features Material: HSS‑Co (cobalt high‑speed steel) Standard: DIN 850 D, Type N Cylindrical shank with drive flat Suitable for construction, case‑hardened and quenched steels Suitable for short‑chipping non‑ferrous metals FAQ What materials can this slot cutter machine? The MAYKESTAG slot cutter (SKU 4117802234NW) is suitable for machining construction steels, case‑hardened and quenched steels, and short‑chipping non‑ferrous metals thanks to its HSS‑Co composition and Type N geometry. Which shank size is required for secure clamping? A 10 mm collet or chuck is required; the cutter has a 10 mm shank with a drive flat for reliable concentricity and secure clamping. Is the geometry suited for high‑feed applications? The 10‑edge configuration supports higher feed rates with controlled chip formation, making the tool appropriate for efficient material removal where machine power and stability allow. Does the cutter conform to an industrial standard? Yes, the tool conforms to DIN 850 D and is specified as Type N, which provides standardised geometry and predictable cutting behaviour. Can this cutter be used for finishing passes? The cutter’s fine flute count and HSS‑Co material enable good surface quality; however, finishing performance will depend on machining parameters and workpiece material. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Take advantage of a robust HSS‑Co construction, precise 22.5 mm diameter and 10 cutting edges for stable slot machining in steels and short‑chipping non‑ferrous metals; order directly via Metav Werkzeuge or consult Metav’s specialists for application advice. MAYKESTAG Slot cutter (DIN 850 D, Type N) – 22.5 mm, HSS‑Co, 10 flutes A MAYKESTAG slot cutter in HSS‑Co, engineered for slotting and peripheral milling of construction and tempered steels as well as short‑chipping non‑ferrous metals, supplied with a cylindrical shank and drive flat for secure clamping. HSS‑Co cutting material for high wear resistance 22.5 mm diameter for precise slotting 10 cutting edges for smooth chip removal Cylindrical shank with drive flat for secure clamping Reliable material choice for demanding milling tasks The cobalt high‑speed steel (HSS‑Co) composition gives the cutter elevated hot hardness and wear resistance compared with standard HSS, which leads to longer cutting life when machining tougher steels. This material choice enables consistent dimensional accuracy and reduced tool change frequency, supporting continuous production runs. The DIN 850 D Type N specification indicates suitability for general slotting tasks in workshop and light industrial settings, providing a predictable performance basis for production planning. Design that improves chip control and surface finish With 10 flutes, the tool balances chip evacuation and cutting engagement to reduce vibration and produce a cleaner slot surface. The right‑hand cutting direction and precisely ground cutting edges assist in achieving a uniform finish while limiting burr formation on the workpiece. The 22.5 mm diameter and the cutter’s flute geometry help maintain stability during plunge or peripheral cutting, which is particularly beneficial when working on short‑chipping non‑ferrous materials and construction steels that demand repeatable results. Practical shaft and mounting details for secure operation The cutter is supplied with a 10 mm cylindrical shank and a drive flat, ensuring secure clamping in collets or toolholders commonly used in milling centres and bench mills. The combination of shank geometry and cutter length supports straightforward tool changes and reliable concentricity in high‑precision setups. For shops consolidating supplies, the tool’s compatibility with standard holders reduces setup time and streamlines tooling inventories. Contact Metav Werkzeuge for tailored recommendations on integrating the MAYKESTAG slot cutter into existing machining processes and to request the SKU 4117802235NW for procurement or specification clarifications Technical Data Article number: 4117802235NW Brand: MAYKESTAG Product type: Slot cutter Facts Diameter: 22.5 mm Total length: 63 mm Cutting length: 10 mm Shank diameter: 10 mm Number of cutting edges: 10 Cutting direction: Right‑hand Special features Material: HSS‑Co Standard: DIN 850 D Type: N Application: milling of construction, case‑hardened and quenched steels; short‑chipping non‑ferrous metals Shank: cylindrical with drive flat FAQ What materials is this slot cutter suitable for? The MAYKESTAG slot cutter 4117802235NW is intended for construction, case‑hardened and quenched steels and for short‑chipping non‑ferrous metals, thanks to its HSS‑Co material and DIN 850 D Type N design. How does the number of flutes affect performance? With 10 flutes, the cutter offers an improved balance between chip removal and cutting engagement, which helps the MAYKESTAG slot cutter deliver smoother surfaces and reduced vibration during slotting. Is the shank compatible with standard collets? The tool’s 10 mm cylindrical shank and drive flat are compatible with common collets and toolholders, providing secure clamping for stable operation of the MAYKESTAG slot cutter. Does the cutter require a specific cutting direction? This cutter is right‑hand cutting, so machining setups should be configured accordingly to ensure correct feed direction and optimal chip flow when using the MAYKESTAG tool. Which aspects should be considered when selecting feeds and speeds? Feeds and speeds should be chosen based on workpiece material and machine rigidity; the HSS‑Co composition of this cutter allows slightly higher operating temperatures than standard HSS, but conservative parameters are recommended for hardened steels to prolong life. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Take advantage of the combination of HSS‑Co wear resistance and a DIN 850 D Type N geometry for reliable slotting in construction and heat-treated steels; the secure 10 mm cylindrical shank ensures stable clamping and repeatable results—order via Metav Werkzeuge or consult our advisors for application support. MAYKESTAG slot milling cutter DIN 850D, 22.5 mm, HSS‑Co, 10 flutes A MAYKESTAG slot milling cutter (DIN 850 D, Type N) designed for slotting and face milling in construction, case‑hardened and quenched steels as well as short‑chipping non‑ferrous metals HSS‑Co for high wear resistance DIN 850 D Type N geometry 22.5 mm diameter, 10 flutes Cylindrical shank with drive flat Durable material for demanding machining tasks Manufactured from HSS‑Co (cobalt alloyed high‑speed steel), this slot cutter delivers increased red‑hardness and wear resistance, which prolongs tool life when machining tougher steels. Cobalt content raises the permissible cutting temperature, so the cutter maintains edge integrity under intermittent heavy loads. For workshops seeking consistent end results with fewer tool changes, the material choice reduces downtime and supports higher productivity in daily metalworking routines. Geometry and flute count optimised for clean slots The DIN 850 D Type N profile with 10 flutes provides a balance between cutting stability and surface finish. A higher flute count improves radial stiffness and reduces tool deflection, resulting in consistent slot dimensions and a smoother milled surface. The cutter’s right‑hand cutting action and defined 10 mm cutting length support precise step‑over strategies in both CNC and manual milling operations, while its tooth geometry is suitable for short‑chipping non‑ferrous metals and a range of steels where chip control is critical. Shank and dimensions engineered for secure clamping A 10 mm cylindrical shank with drive flat ensures reliable transmission of torque and simple, repeatable clamping in standard collets and chucks. With a 22.5 mm diameter and 63 mm overall length, the tool is compact enough for close‑tolerance slotting yet long enough for common fixture setups. The combination of shank design and balanced tool proportions reduces vibration, supporting improved tool life and stable cutting conditions in both batch production and single‑part manufacturing. Practical advantages for everyday workshop use The cutter’s standards‑based design simplifies tool selection and integration: conformity with DIN 850 D makes the geometry predictable across applications and tooling systems. The 10‑flute layout supports tighter step‑overs when surface finish matters, while the HSS‑Co substrate helps maintain performance when brief temperature peaks occur. For engineers and technicians who require dependable slotting performance without complex set‑up, this tool provides a straightforward, robust option. Contact Metav Werkzeuge for tailored advice on application suitability and stock availability; phone +49 2822 7131930 or email info@metav-werkzeuge.com and reference SKU 4117802236NW for a fast consultation Technical Data Article number: 4117802236NW Label: Schlitzfräser DIN 850D TypN D.22,5mm HSS‑Co Z.10 L.8mm MAYKESTAG Core Data Diameter: 22.5 mm Overall length: 63 mm Cutting length: 10 mm Number of cutting edges: 10 Shank diameter: 10 mm Cutting direction: right‑hand Packaging unit: 1 Special features Material: HSS‑Co Standard: DIN 850 D, Type N Application: milling of construction, case‑hardened and quenched steels; short‑chipping non‑ferrous metals Shank: cylindrical shank with drive flat FAQ What materials is this cutter suitable for? The MAYKESTAG slot milling cutter is specified for milling construction, case‑hardened and quenched steels as well as short‑chipping non‑ferrous metals, reflecting the HSS‑Co substrate and Type N geometry. What are the key dimensions to consider for clamping? Shank diameter is 10 mm with a cylindrical shank and drive flat; overall length is 63 mm and cutter diameter is 22.5 mm, SKU 4117802236NW. How many flutes does the cutter have and what does that mean for cutting? The tool has 10 flutes; the higher flute count improves rigidity and surface finish, making it suitable for tighter step‑overs where a smooth slot surface is required. Is the cutter right‑hand or left‑hand cutting? The cutter is right‑hand cutting, designed for conventional slotting and face milling orientations. What standard does the tool conform to and why is that important? It conforms to DIN 850 D, Type N, which ensures standardised geometry for predictable machining behaviour and easier integration into existing tool inventories. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Take advantage of a robust HSS‑Co cutting grade and a DIN 850 D Type N geometry for reliable slotting in construction and tempered steels; order directly via Metav Werkzeuge or consult the team for application data. MAYKESTAG Slot Milling Cutter DIN 850 D Typ N – 25.5 mm, HSS‑Co The MAYKESTAG slot milling cutter DIN 850 D Typ N is a right‑hand slotting tool engineered for producing precise slots and grooves in construction, case‑hardened and tempered steels as well as short‑chipping non‑ferrous metals HSS‑Co cutting material for demanding steels DIN 850 D, Type N geometry for slot milling 25.5 mm diameter for medium‑width slots Cylindrical shank with drive flat for secure clamping Durable substrate and geometry for repeatable cuts The tool is manufactured from HSS‑Co, a cobalt‑alloyed high‑speed steel that retains hardness at elevated cutting temperatures, which leads to longer service life under intermittent heavy load. The DIN 850 D specification and Type N tooth form are designed to balance edge strength and chip control when slotting across a range of steels. Right‑hand cutting combined with the chosen tooth count ensures predictable chip flow when machining short‑chipping non‑ferrous metals and medium‑hard steels, reducing the likelihood of built‑up edge and improving process stability. Consistent slot geometry and surface quality With a 25.5 mm nominal diameter and a 10 mm cutting length, the cutter provides a compact profile suitable for confined fixtures and precise slot depths. The tool’s overall length of 63 mm and 10 flutes deliver a favourable contact ratio for improved surface finish on milled slot faces. These dimensions support controlled cutting engagement and help achieve a uniform surface finish with fewer passes, which benefits finishing operations and reduces subsequent deburring work. Secure clamping and machine compatibility The cutter features a cylindrical shank with a drive flat, enabling dependable seating in collets and tool holders and promoting secure clamping under radial and axial loads. The 10 mm shank diameter matches common collet sizes used in both manual and CNC milling centres, simplifying tool changes and inventory management. This mechanical compatibility, together with the tool’s robust grade, supports repeatable setup and contributes to reduced downtime in mixed‑batch production environments. Typical applications and handling recommendations Ideal for slot milling of grooves, keyways and shallow pockets in construction and tempered steels, this cutter suits operations that demand a compromise between edge strength and finish. For best results, select machining parameters that reflect the workpiece material and machine rigidity; incremental feeds and consistent coolant application will extend tool life and maintain dimensional accuracy. For tailored cutting data or material‑specific advice, consult Metav Werkzeuge’s technical team before first use. Contact Metav Werkzeuge in Emmerich for tailored cutting data and fast supply at info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: 4117802237NW Material: HSS‑Co Product type: Slot milling cutter Manufacturer: ALPEN‑MAYKESTAG GmbH Cutting edges: 10 Diameter: 25.5 mm Overall length: 63 mm Cutting length: 10 mm Shank diameter: 10 mm Cutting direction: Right‑hand cutting Facts Ø: 25.5 mm Overall length: 63 mm Cutting length: 10 mm Shank Ø: 10 mm Cutting edges: 10 Special features DIN 850 D, Type N geometry HSS‑Co cutting grade Cylindrical shank with drive flat Suitable for construction, case‑hardened and tempered steels Also suitable for short‑chipping non‑ferrous metals Right‑hand cutting FAQ Which materials is this cutter suitable for? The MAYKESTAG slot milling cutter (SKU 4117802237NW) with HSS‑Co is suitable for construction steels, case‑hardened and tempered steels and for short‑chipping non‑ferrous metals. What clamping system is required? Clamp the tool by its 10 mm shank in a matching collet or holder; the cylindrical shank with drive flat ensures positive seating and stable clamping for the cutter. What surface quality can be expected? Thanks to the 10 flutes and Type N geometry, the cutter produces a favourable finish on slot faces, reducing the need for secondary finishing in many applications. Is the cutter right‑hand or left‑hand? This cutter is right‑hand cutting, designed for standard clockwise spindle rotation during slot milling. Which operations are typical for this tool? Typical uses include slot milling, producing keyways and shallow grooves in medium‑to‑high‑strength steels and in short‑chipping non‑ferrous materials. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Take advantage of a durable cutter that combines cobalt high‑speed steel construction, a 28.5 mm diameter and a 12‑tooth geometry for efficient slotting in a range of steels and short‑chipping non‑ferrous metals; order directly via Metav Werkzeuge or contact our consultants for application advice. MAYKESTAG Slot Milling Cutter DIN 850 D — 28.5 mm HSS‑Co, 12 Teeth A MAYKESTAG slot milling cutter designed for precise slotting and groove machining in construction, quenched and tempered steels and short‑chipping non‑ferrous metals Cobalt high‑speed steel HSS‑Co Complies with DIN 850 D 12 cutting edges for smooth material removal Cylindrical shank with drive flat Consistent results from a cobalt HSS core The cutter is made from HSS‑Co (cobalt‑alloyed high‑speed steel), which provides a balance between toughness and hot‑hardness compared with ordinary high‑speed steel. This material choice improves resistance to thermal softening during interrupted cuts, resulting in a longer effective tool life and more consistent machining performance when producing slots and grooves. The DIN 850 D designation ensures a defined geometry and manufacturing standard, which helps to predict cutting behaviour and makes the tool suitable for industrial production environments. Efficient chip control and surface quality With 12 teeth and a right‑hand cutting direction, the geometry supports steady chip formation and evacuation when machining short‑chipping materials such as brass, aluminium and certain non‑ferrous alloys. The cutter’s tooth count and geometry reduce vibration and promote a cleaner finish on the slot wall, delivering time savings through fewer finishing passes and predictable surface quality. For applications involving hardened or heat‑treated steels, the cutter’s design maintains cutting stability under moderate feed rates. Secure clamping and machine compatibility A 12 mm cylindrical shank with drive flat provides reliable clamping in standard collets and chucks, reducing the risk of slippage during higher torque operations. The tool’s overall length of 71 mm and cutting length of 12 mm permit use in common milling setups where moderate reach and rigidity are required. The combination of shank design and balanced geometry supports repeatable positioning and helps to reduce setup time on vertical milling machines and CNC centres. Practical advantages for workshop operations Specification conformity to DIN 850 D and the use of HSS‑Co mean the tool is straightforward to regrind and maintain, extending service life and lowering per‑slot costs in the long term. The tool is intended for slotting in construction and tempered steels as well as for machining short‑chipping non‑ferrous metals, which makes it a versatile choice for small series production and repair work. This predictability and maintainability support continuous workflow and reduce downtime in busy workshops. For technical advice on application suitability or to procure the MAYKESTAG HSS‑Co slot milling cutter, contact Metav Werkzeuge for tailored guidance and reliable supply at info@metav-werkzeuge.com or +49 2822 7131930 Technical Data Article number: 4117802240NW Product type: Slot milling cutter Brand: ALPEN‑MAYKESTAG GmbH SKU: 4117802240NW Facts Diameter: 28.5 mm Cutting length: 12 mm Overall length: 71 mm Shank diameter: 12 mm Teeth: 12 Cutting direction: Right‑handing Special features Material: HSS‑Co (cobalt high‑speed steel) Standard: DIN 850 D Type: N Cylindrical shank with drive flat For machining construction, quenched and tempered steels and short‑chipping non‑ferrous metals Packaging unit: 1 FAQ What materials is this slot milling cutter suitable for? The MAYKESTAG slot milling cutter is designed for machining construction steels, quenched and tempered steels and short‑chipping non‑ferrous metals as stated in the product specification (SKU 4117802240NW). Can the cutter be regrinded after use? Yes, tools manufactured from HSS‑Co, such as this slot cutter, can generally be regrinded to restore the cutting edges, extending tool life with correct workshop practice. Will the 12 mm shank fit standard collet systems? The 12 mm cylindrical shank with a drive flat provides compatibility with standard collets and clamping systems commonly used on milling machines and CNC centres. Is the tool suitable for high‑speed machining? The cutter is made from HSS‑Co and is intended for robust slotting operations; for very high cutting speeds, application parameters and machine capability should be checked against material and process requirements. Which standard defines the tool geometry? The cutter conforms to DIN 850 D, which standardises the tool type (N) and geometry to ensure predictable cutting behaviour. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Take advantage of a robust HSS‑Co construction, a substantial Ø 28.5 mm cutting diameter and a secure cylindrical shank for dependable slot milling in mixed production environments. Order the MAYKESTAG slot cutter directly via Metav Werkzeuge or consult our specialists for integration advice. MAYKESTAG Slot cutter DIN 850 D Typ N — Ø 28.5 mm, HSS‑Co, 12 teeth The Slot cutter DIN 850 D Typ N is a precision milling cutter designed for slotting tasks in construction, case‑hardening and quenched‑and‑tempered steels as well as for short‑chip non‑ferrous metals HSS‑Co high‑performance cutting steel Ø 28.5 mm diameter for medium slots 12 cutting edges for smooth chip formation Cylindrical shank with drive flat, Ø 10 mm Right‑hand cutting direction for standard milling Durable cutting performance for mixed steels and non‑ferrous alloys The use of HSS‑Co (cobalt‑alloyed high‑speed steel) provides increased heat resistance and fracture toughness compared with standard high‑speed steel, resulting in longer tool life under elevated cutting temperatures. Conforming to DIN 850 D and constructed as Type N, this cutter is optimised for short‑chip applications and intermittent engagement, which supports stable milling processes when working with construction steels, case‑hardening grades and short‑chipping non‑ferrous materials. The material selection benefits workshop throughput by reducing tool changes and maintaining dimensional accuracy over longer production runs. Geometry and tooth count for consistent surface quality With 12 teeth and a geometry tailored to short‑chip removal, the cutter delivers a balance of feed rate and surface finish: more flutes permit higher feed per revolution while preserving a fine slot wall. The right‑hand cutting orientation matches standard milling setups and ensures predictable chip flow. The specified 12 mm cutting length provides sufficient engagement depth for typical slotting operations while limiting deflection, which improves repeatability and reduces rework in precision assemblies. Secure holding and compact dimensions for reliable machining A cylindrical shank with drive flat offers positive torque transfer and simplifies clamping with standard collets and chucks, while the Ø 10 mm shank and 63 mm overall length make the tool suitable for compact toolholders and limited‑reach setups. The combination of reduced overhang and a robust shank reduces vibration and improves tool life; this leads to fewer interruptions in production and a more predictable machining cadence for small to medium batch sizes. For bespoke advice on integrating the MAYKESTAG slot cutter into production or to request detailed technical data, contact Metav Werkzeuge in Emmerich at info@metav-werkzeuge.com or call +49 2822 7131930 for rapid support and reliable supply Technical data Article number: 4117802239NW Product: Slot cutter Brand: ALPEN‑MAYKESTAG GmbH Facts Diameter: Ø 28.5 mm Overall length: 63 mm Cutting length: 12 mm Shank diameter: Ø 10 mm Cutting edges: 12 Special features Material: HSS‑Co Right‑hand cutting Norm: DIN 850 D, Type N Cylindrical shank with drive flat Suitable for construction, case‑hardening and quenched‑and‑tempered steels Suitable for short‑chip non‑ferrous metals FAQ What materials is this cutter suitable for? The MAYKESTAG slot cutter (slot cutter, SKU 4117802239NW) is suitable for construction steels, case‑hardening and quenched‑and‑tempered steels, and for short‑chip non‑ferrous metals. What are the tool dimensions and shank size? The cutter has a diameter of Ø 28.5 mm, an overall length of 63 mm and a shank diameter of Ø 10 mm. How many cutting edges does the tool have and what finish can be expected? With 12 cutting edges the tool provides smooth chip formation and a consistent surface finish when used with appropriate feeds and speeds. Is this cutter compatible with standard toolholders? Yes; the cylindrical shank with drive flat is designed for secure clamping in standard collets and chucks used in milling operations. Which standard does the cutter comply with? The tool conforms to DIN 850 D, Type N, indicating geometry and application suitability for short‑chip milling tasks. Manufacturer: ALPEN‑MAYKESTAG GmbH / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Take advantage of the combination of HSS‑Co cutting performance, a Ø28.5 mm cutting diameter and a robust Ø10 mm shank with drive flat for reliable power transmission; order the tool directly via Metav Werkzeuge or request consultancy for application-specific recommendations. MAYKESTAG slotting cutter DIN 850 D Type N, Ø28.5 mm, HSS‑Co A robust MAYKESTAG slotting cutter designed for precision slot and groove milling in demanding steels and short‑chip non‑ferrous metals. HSS‑Co for demanding steels and alloys 12 cutting edges for efficient stock removal DIN 850 D, Type N for slotting applications Cylindrical shank with drive flat, Ø10 mm Consistent slotting performance through high‑grade cobalt steel This slotting cutter is manufactured from HSS‑Co, a cobalt‑enriched high‑speed steel that maintains hardness at elevated temperatures and thus supports consistent cutting performance during demanding operations. The combination of the Ø28.5 mm diameter and 12 cutting edges enables a balance between material removal rate and surface quality, reducing the need for repeat passes and keeping cycle times predictable. For production environments where process stability matters, the cobalt alloy offers extended tool life compared with conventional high‑speed steel. Clear application range and machining advantages Engineered according to the DIN 850 D specification and designated Type N, the cutter is intended for milling structural, tool and quenched‑and‑tempered steels as well as short‑chipping non‑ferrous metals. Short‑chip materials include many aluminium alloys and other metals that form manageable swarf rather than long, stringy chips; this behaviour reduces the risk of chip entanglement and helps maintain consistent feed. The result is a more reliable process in mixed‑material shops and when switching between ferrous and suitable non‑ferrous stock. Shank and geometry engineered for secure power transfer The cylindrical shank with drive flat (Ø10 mm) ensures secure seating in conventional tool holders and milling chuck systems, reducing slippage under load and enabling repeatable positioning. With an overall length of 63 mm and a cutting length of 12 mm, the tool offers sufficient reach for many slotting tasks while keeping deflection low. Right‑hand cutting geometry supports conventional milling setups and promotes stable chip removal when paired with suitable feeds and speeds. Compliance with the DIN standard additionally simplifies process documentation and tool selection in industrial settings. Why this cutter fits professional workshops and small series production For toolrooms and production workshops seeking a cost‑effective route to high‑precision slotting, the cutter delivers a rational performance profile: durable HSS‑Co construction, proven geometry and standardised dimensions that integrate with existing fixtures. The result is reliable throughput and reduced rework. Metav’s role as an experienced precision partner complements the product: decades of distribution and a European quality filter in Emmerich help ensure consistent supply and expert advice for integration into existing tool fleets. Choose the MAYKESTAG HSS‑Co slotting cutter for dependable slotting results — contact Metav Werkzeuge for tailored procurement and technical guidance from Emmerich. Technical data SKU: 4117802238NW Item: Slotting cutter DIN 850 D Type N Brand: MAYKESTAG Manufacturer: ALPEN‑MAYKESTAG GmbH Facts Diameter: 28.5 mm Overall length: 63 mm Cutting length: 12 mm Shank diameter: 10 mm Cutting edges: 12 Cutting direction: right‑hand cutting Special features Material: HSS‑Co Standard: DIN 850 D Type: N Cylindrical shank with drive flat For milling structural, tool and quenched‑and‑tempered steels and short‑chipping non‑ferrous metals FAQ What materials is this slotting cutter suitable for? The cutter is specified for milling structural, tool and quenched‑and‑tempered steels and for short‑chipping non‑ferrous metals, as noted in the DIN 850 D Type N designation. How many cutting edges does the tool have and what is the effect? The tool features 12 cutting edges, which promotes efficient stock removal while helping to preserve surface finish and extend tool life under appropriate cutting conditions. What shank size is required for mounting the cutter? The tool has a Ø10 mm cylindrical shank with a drive flat designed for secure clamping in standard chucks and tool holders. Is the cutter compliant with industry standards? Yes; the cutter is produced to DIN 850 D and carries the Type N specification suitable for slotting applications. Which SKU should be referenced when ordering or requesting technical data? Reference SKU 4117802238NW and the MAYKESTAG slotting cutter to ensure the correct item is supplied. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Take advantage of the HSS‑Co cutting material, the DIN 850 D, Type N geometry and the compact 32.5 mm diameter to achieve consistent slotting performance in a range of steels and short‑chipping non‑ferrous metals. Order directly via Metav Werkzeuge or contact the consultants for tailored technical support. MAYKESTAG slot milling cutter DIN 850 D, 32.5 mm, HSS‑Co The MAYKESTAG slot milling cutter is a right‑hand cutting tool designed for precision slotting in construction, case‑hardened and tempered steels as well as short‑chipping non‑ferrous metals HSS‑Co cutting material for high wear resistance DIN 850 D, Type N for robust steel machining 12 cutting edges for smooth, fine slotting Cylindrical shank with drive flat, 12 mm diameter Consistent cutting performance through material and standard The cutter is manufactured from HSS‑Co (cobalt high‑speed steel), a material selected for its increased hot hardness and wear resistance compared with standard high‑speed steels. Combined with the DIN 850 D, Type N specification, this equips the tool for repeated work on construction and quenched‑and‑tempered steels while maintaining edge stability. For workshops and production lines, the result is fewer tool changes and a noticeable improvement in process reliability when machining medium‑to‑high strength materials. Geometry and chip control that improve surface quality With 12 cutting edges and a right‑hand cut geometry, the tool provides fine chip segmentation and steady cutting forces, which reduces vibration and improves slot surface finish. The 12 mm shank with drive flat ensures secure clamping and positive torque transmission in standard collet or chuck systems. These design choices translate into predictable machining behaviour and reduced need for rework when producing slots, grooves or keyways in mixed‑material batches. Compact design to speed up setup and reduce downtime The tool’s 32.5 mm diameter, 12 mm cutting length and 71 mm overall length make it suitable for constrained set‑ups where reach and rigidity must be balanced. The combination of compact form and robust material means the cutter performs well in repetitive tasks, helping to keep cycle times steady and order throughput dependable. For machine shops seeking a pragmatic balance between tool life and flexibility, this cutter provides a reliable option for series production and repair work alike. For additional technical details or to verify compatibility with specific machines and materials, Metav’s technical team is available at info@metav-werkzeuge.com or by phone on +49 2822 7131930 Choose the MAYKESTAG slot milling cutter for dependable slotting in demanding materials — purchase via Metav Werkzeuge for secure supply from Emmerich and direct access to technical advice: info@metav-werkzeuge.com / +49 2822 7131930 Technical data Article number: 4117802242NW Product type: Slot milling cutter Brand: MAYKESTAG Manufacturer: ALPEN‑MAYKESTAG GmbH Packing unit: 1 Facts Diameter: 32.5 mm Overall length: 71 mm Cutting length: 12 mm Cutting edges: 12 Shank diameter: 12 mm Cutting direction: right‑hand cut Special features Material: HSS‑Co (cobalt high‑speed steel) Standard: DIN 850 D, Type N Application: milling of construction, case‑hardened and tempered steels; short‑chipping non‑ferrous metals Shank: cylindrical with drive flat FAQ What materials is this cutter suitable for? The MAYKESTAG slot milling cutter is specified for machining construction steels, case‑hardened and quenched‑and‑tempered steels, and short‑chipping non‑ferrous metals thanks to its HSS‑Co composition and DIN 850 D, Type N geometry. Is the shank compatible with standard collets? Yes, the 12 mm cylindrical shank with drive flat is designed for secure clamping in standard collet chucks and toolholders used in conventional milling machines and machining centres. How many cutting edges does the tool have and what is the benefit? This cutter has 12 cutting edges, which promote fine chip division and steady cutting forces, improving surface finish and reducing vibration during slotting operations. Can the cutter be used for slotting in aluminium and copper alloys? The tool’s geometry and HSS‑Co material make it suitable for short‑chipping non‑ferrous metals, including many aluminium and copper alloys; machining parameters should be adapted to alloy and feed conditions. What is the product reference for ordering? Order reference / SKU: 4117802242NW for the MAYKESTAG slot milling cutter Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Take advantage of a tool that combines HSS‑Co hardness with a compact Ø4.5 mm form factor and a six‑flute geometry for steady chip control; the result is reliable slotting performance in construction and tempered steels with minimal vibration. Order the cutter directly via Metav Werkzeuge or contact our consultants for compatibility advice. Slot cutter DIN 850 D Type N, Ø4.5 mm – HSS‑Co, 6 flutes (MAYKESTAG) A slot cutter DIN 850 D Type N designed for precision slotting in construction, case‑hardened and tempered steels and for short‑chipping non‑ferrous metals, supplied with a cylindrical shank and drive flat. HSS‑Co for high wear resistance Six flutes for smooth material removal Precision Ø4.5 mm cutting diameter Cylindrical shank with drive flat Faster, dependable cuts in demanding materials The HSS‑Co composition gives the cutter increased hot hardness and edge retention compared with conventional high‑speed steel, so machining cycles remain consistent even under intermittent load. This makes the tool particularly suited to short‑chipping materials and alloyed structural steels where chip formation and tool life are critical. By specifying a tool made to DIN 850 D, workshops receive a standardised geometry that simplifies process planning and reduces scrap from incorrect tool selection. Smooth surface finish through optimised flute geometry A geometry with six flutes minimises radial forces and improves chip evacuation on shallow slotting operations. The result is a cleaner slot and reduced tendency for chatter, which benefits both manual and CNC setups. The 6 mm cutting length is optimised for controlled engagement in panel or component edges, providing a balance between reach and rigidity; the shorter effective cutting zone keeps deflection low and helps maintain tolerances with every pass. Secure clamping and compatibility with common toolholders The cylindrical shank with a drive flat is engineered for reliable gripping in standard collets and chuck systems, preventing slippage during interrupted cuts. A shank diameter of 6 mm matches common workshop tooling, permitting quick tool changes and straightforward integration into existing tool sets. Overall length of 50 mm gives enough reach for many slotting tasks while keeping the clamped length sufficient for stable operation. Designed for everyday workshop and small‑batch production Manufactured by ALPEN‑MAYKESTAG, the cutter is intended for routine use in repair shops, toolrooms and small production lines where predictable performance is essential. The right‑hand cutting direction aligns with standard feed orientations and simplifies operator instructions. For operations that cycle between steels and short‑chipping non‑ferrous metals, the combination of material and flute count reduces the need for multiple specialised cutters, streamlining inventory and set‑up times. Discuss machining requirements with Metav Werkzeuge — our specialists will advise on the MAYKESTAG slot cutter (SKU 4117802220NW), compatibility with holders and recommended feeds and speeds; contact info@metav-werkzeuge.com or call +49 2822 7131930 for tailored guidance Technical data Article number: 4117802220NW Product: Slot cutter DIN 850 D Type N Manufacturer: ALPEN‑MAYKESTAG GmbH Core specifications Diameter: 4.5 mm Overall length: 50 mm Cutting length: 6 mm Shank diameter: 6 mm Flutes: 6 Cutting direction: right‑hand cutting Special features Material: HSS‑Co Norm: DIN 850 D, Type N For machining construction, case‑hardened and tempered steels Suitable for short‑chipping non‑ferrous metals Cylindrical shank with drive flat FAQ What materials can this slot cutter machine effectively? The slot cutter from ALPEN‑MAYKESTAG is designed for construction, case‑hardened and tempered steels and is also suitable for short‑chipping non‑ferrous metals as specified for the Type N DIN 850 D design. Which shank size is required for this tool? The cutter features a 6 mm shank diameter and a drive flat, matching standard 6 mm collets and chucks for secure clamping of the MAYKESTAG slot cutter (SKU 4117802220NW). How many flutes does the cutter have and what is the benefit? This tool has six flutes; the increased flute count improves surface finish and reduces vibration during slotting, leading to steadier cuts and better dimensional control. Is the cutter suitable for CNC and manual milling machines? Yes; the combination of HSS‑Co material, standardised DIN 850 D geometry and a cylindrical shank with drive flat makes the cutter compatible with both CNC and manual milling setups. Where can feed and speed recommendations be obtained? For tailored feeds and speeds for the MAYKESTAG slot cutter (ALPEN‑MAYKESTAG, SKU 4117802220NW), consult Metav Werkzeuge’s technical team who can advise based on the workpiece material and machine characteristics. Manufacturer: ALPEN‑MAYKESTAG GmbH; Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

The combination of HSS‑Co construction and 14 cutting edges delivers steady performance and extended tool life for demanding slotting tasks; the robust Ø45.5 mm diameter and cylindrical shank with drive flat ensure secure clamping and consistent results. Order the cutter via Metav Werkzeuge or consult the technical team if specialised milling parameters are required. MAYKESTAG Slot cutter DIN 850D Type N, Ø45.5 mm, HSS‑Co The MAYKESTAG slot cutter DIN 850D Type N is a heavy‑duty milling tool designed for precise slotting in construction, case‑hardened and quenched‑and‑tempered steels, as well as short‑chipping non‑ferrous metals. Robust HSS‑Co construction for long tool life 14 cutting edges for smooth chip control Ø45.5 mm diameter for wide slotting tasks Cylindrical shank with drive flat for secure clamping High‑performance material for consistent cutting results The use of HSS‑Co (cobalt‑alloyed high‑speed steel) provides a balance between hardness and toughness that supports higher cutting temperatures and longer tool life than standard high‑speed steels. This material choice reduces the risk of premature wear when milling medium‑strength and heat‑treated steels; as a result, machining intervals are extended and unplanned tool changes are less frequent. The cutter’s grade is optimised for short‑chipping operations, contributing to reliable surface quality and repeatable slot dimensions. Geometry and clamping that support accuracy and stability A Ø45.5 mm body combined with 14 cutting edges ensures even material engagement and improved chip division, which helps to avoid chatter in stable setups. The tool’s 14 mm cutting length concentrates effective cutting where required, while the 12 mm shank diameter and cylindrical shank with drive flat permit rigid clamping in common collets and toolholders. The cutter is right‑hand cutting, which corresponds to standard spindle rotation and simplifies setup. Together these features reduce vibration and support consistent dimensional tolerances in series production. Applications across steels and short‑chipping non‑ferrous metals Designed according to DIN 850 D as Type N, the cutter is suitable for slotting and face milling of construction steels, case‑hardened components and quenched‑and‑tempered materials, as well as non‑ferrous metals that form short chips during machining. The tool’s geometry favours processes where controlled chip breaking and surface finish are required, such as slotting for keyways, machining of housings or preparing seats for secondary operations. Selection of appropriate feeds and speeds for the chosen workpiece material will further enhance life and finish. Operational efficiency and straightforward maintenance The tool’s specification supports productivity: a sturdy HSS‑Co body tolerates intermittent cutting and higher temperatures, while the multi‑edge configuration spreads wear over several flutes to delay regrinding. Reconditioning is practical because the core material is a recognised high‑speed grade. For workshop planning, the compact overall length and standard shank size make integration into existing tool cycles straightforward, and the robust design helps reduce spindle downtime and maintain a steady throughput in batch operations. For demanding slotting tasks trust the MAYKESTAG cutter’s HSS‑Co construction and robust geometry — contact Metav Werkzeuge for application advice and reliable supply from Emmerich. Technical data Article number: 4117802243NW Manufacturer: ALPEN‑MAYKESTAG GmbH Product type: Slot cutter Material: HSS‑Co Packaging unit: 1 Cutting direction: Right‑hand cutting Dimensions & performance Diameter: Ø45.5 mm Overall length: 71 mm Cutting length: 14 mm Number of cutting edges: 14 Shank diameter: 12 mm Standards & special features DIN 850 D, Type N Cylindrical shank with drive flat Suited for construction, case‑hardened and quenched‑and‑tempered steels Suitable for short‑chipping non‑ferrous metals Zylinderschaft mit Mitnahmefläche (cylindrical shank with drive flat) FAQ What materials is this slot cutter suitable for? The MAYKESTAG slot cutter (DIN 850D Type N, SKU 4117802243NW) is specified for construction steels, case‑hardened and quenched‑and‑tempered steels, and for short‑chipping non‑ferrous metals. How does the HSS‑Co composition benefit milling? HSS‑Co provides greater hot hardness and wear resistance compared with standard high‑speed steels, so the cutter maintains cutting performance and requires fewer changes under higher thermal loads. What size of collet or holder is required for the shank? A 12 mm collet or compatible holder is required to clamp the cylindrical shank; the drive flat improves torque transmission and reduces slippage during heavy engagement. Is the cutter balanced for high‑speed milling? The tool’s multi‑edge geometry and solid HSS‑Co construction support stable running in conventional slotting speeds; final balancing and allowable speeds depend on the machine spindle and clamping arrangement. Can the cutter be reconditioned after wear? As a solid HSS‑Co cutter, the tool can be reconditioned by reviving cutting edges where appropriate; regrinding should respect the original geometry and DIN 850 D parameters to retain performance. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Take advantage of the cutter's HSS‑Co composition, compact 7.5 mm diameter and six‑flute geometry for reliable slotting in short‑chipping materials; order directly via Metav Werkzeuge or contact the sales team for tailored advice. Slot cutter DIN 850 D Type N — 7.5 mm, HSS‑Co, 6 flutes (ALPEN‑MAYKESTAG) The Slot cutter DIN 850 D Type N is a purpose‑built milling tool for precise slotting and groove work in construction, case‑hardened and quenched steels as well as short‑chipping non‑ferrous metals. Cobalt high‑speed steel for long tool life 7.5 mm diameter for accurate slotting Six flutes for improved chip evacuation Cylindrical shank with drive flat for secure hold Consistent cutting performance for efficient production The cutter’s HSS‑Co composition delivers a balance of hardness and toughness that supports consistent material removal under moderate cutting speeds. Combined with the six‑flute geometry, the tool produces smaller, controllable chips which reduces machining interruptions and extends uninterrupted run times. For operations on construction steels and short‑chipping non‑ferrous alloys, this results in a measurable increase in process reliability while maintaining surface quality and dimensional stability. Predictable geometry for accurate slots and grooves With a 7.5 mm cutting diameter and 6 mm shank, the tool provides a compact, stable profile suited to tight slotting tolerances. The cutting length 6 mm and right‑hand cutting orientation ensure familiar behaviour in standard mill setups, while the DIN standardised form (DIN 850 D Type N) simplifies tool selection. The cylindrical shank with drive flat improves clamping security, reducing run‑out and vibration for straighter walls and cleaner edges. Reduced setup complexity and broad machine compatibility The standardised shaft and form factor make the cutter straightforward to integrate into existing toolholders and collet chucks on both manual and CNC milling machines. Its dimensions and geometry support short changeovers and predictable tool offsets, which helps keep cycle times down. For workshops seeking consistent, repeatable slotting without complex retooling, the design focuses on operational ease and repeatability. Robust workshop quality from a recognised maker Manufactured according to DIN 850 D principles and produced by a specialist maker, this cutter combines practical application focus with workshop durability. The tool is intended for everyday production use where precision and reliability matter, offering stable performance for repetitive slotting tasks and small‑batch runs. When paired with Metav Werkzeuge’s logistics and advisory services, the solution supports an efficient supply chain and informed purchasing decisions. Choose the ALPEN‑MAYKESTAG slot cutter for dependable slotting performance and contact Metav Werkzeuge for personalised selection advice — eMail info@metav-werkzeuge.com or call +49 2822 7131930 for further technical information and order support Technical data Article number: 4117802221NW Product: Slot cutter (Schlitzfräser) Brand: ALPEN‑MAYKESTAG GmbH Material: HSS‑Co Core measurements Diameter: 7.5 mm Overall length: 50 mm Cutting length: 6 mm Shank diameter: 6 mm Flutes: 6 Cutting direction: right‑hand Designs and special features DIN 850 D Type N Cylindrical shank with drive flat For milling construction, case‑hardened and quenched steels Suitable for short‑chipping non‑ferrous metals FAQ What materials is this cutter suitable for? The ALPEN‑MAYKESTAG slot cutter is designed for construction steels, case‑hardened and quenched steels, and short‑chipping non‑ferrous metals. Which shank size is required for the tool holder? A 6 mm shank holder is required for the cutter; use a collet or chuck that securely seats a 6 mm cylindrical shank with drive flat. How does the six‑flute geometry affect machining? Six flutes give finer chip division and improved surface finish for short‑chipping materials; the geometry supports steady feed rates and reduced vibration. Is this cutter compatible with CNC milling machines? Yes, the standardised DIN 850 D Type N form and cylindrical shank make the cutter compatible with common CNC and manual milling setups. Can the cutter be reconditioned or reground? Regrinding depends on the remaining core diameter and flute geometry; consult Metav Werkzeuge for serviceability advice for this SKU 4117802221NW. Manufacturer: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Take advantage of a high‑performance HSS‑Co construction and DIN 850 D geometry to combine durable wear resistance with reliable slotting results; the cutter’s 6 flutes and 6 mm cutting length provide smooth chip evacuation and consistent surface finish. Order the slot milling cutter directly via Metav Werkzeuge or consult our specialists for application support. Slot milling cutter DIN 850 D Type N — 7.5 mm HSS‑Co (MAYKESTAG) The slot milling cutter DIN 850 D Type N, 7.5 mm HSS‑Co is designed for slotting and face milling of construction, case‑hardened and quenched steels as well as short‑chipping non‑ferrous materials in production and workshop settings HSS‑Co for high wear resistance DIN 850 D Type N geometry 6 cutting edges for smooth finish Suited for steels and non‑ferrous metals Increase throughput with consistent chip control and surface quality The combination of HSS‑Co tool steel and a Type N geometry gives predictable performance under interrupted and continuous cuts, translating into fewer rework steps and higher first‑pass yield. The tool’s 6 flutes optimise chip load distribution, which reduces vibration and produces a more uniform surface finish on workpieces. For buyers seeking measurable production improvements, this translates into shorter cycle times and more stable process windows when machining medium‑hard steels and short‑chipping alloys. Broad material compatibility reduces tooling variants in the tool crib Constructed from HSS‑Co, the cutter tolerates higher temperatures at the cutting edge than standard HSS, allowing reliable operation in a wide range of materials. The tool is suitable for construction steels, case‑hardened and quenched steels, and short‑chipping non‑ferrous metals, enabling consolidation of tooling stocks. Explaining the term: HSS‑Co means high‑speed steel with cobalt alloying, which offers improved red hardness and abrasion resistance compared with plain high‑speed steels — a clear advantage when tools are used intermittently at higher cutting speeds. Practical design for secure mounting and efficient handling A cylindrical shank with drive flat and a shank diameter of 6 mm ensures a secure grip in standard toolholders and reduced run‑out, which supports higher precision in slotting operations. The tool’s right‑hand cutting orientation and a cutting length of 6 mm match common setup conventions, simplifying programming and fixturing. The cutter’s overall length of 50 mm permits use in many standard vertical and horizontal milling setups without compromising rigidity for typical slot depths. Application guidance and process reliability When used according to machine capabilities and recommended feeds and speeds, the geometry defined by DIN 850 D promotes reliable chip formation and evacuation. For shops less familiar with the standard, DIN 850 D specifies dimensions and tolerances for this kind of cutter, helping engineers select compatible holders and set expected machining parameters. The result is easier process documentation, repeatable setups and less trial‑and‑error during process qualification. For reliable slotting in steels and short‑chipping non‑ferrous metals, choose the MAYKESTAG 7.5 mm HSS‑Co slot milling cutter and contact Metav Werkzeuge for tailored application advice or to place an order: info@metav-werkzeuge.com | +49 2822 7131930 Technical Data Article number: 4117802222NW Label: Schlitzfräser DIN 850D Typ N D.7,5mm HSS‑Co Z.6 L.2mm MAYKESTAG Manufacturer: ALPEN‑MAYKESTAG GmbH Facts Material: HSS‑Co Diameter: 7.5 mm Overall length: 50 mm Cutting length: 6 mm Cutting edges: 6 Shank diameter: 6 mm Cutting direction: right‑hand Special features Conforms to DIN 850 D Type N geometry Cylindrical shank with drive flat Suitable for construction, case‑hardened and quenched steels Suitable for short‑chipping non‑ferrous metals FAQ What materials can be machined with this cutter? The slot milling cutter is designed for construction steels, case‑hardened and quenched steels and for short‑chipping non‑ferrous metals; the HSS‑Co composition provides enhanced heat and wear resistance suitable for these applications. What are the key dimensions and mounting details? The tool has a 7.5 mm diameter, 6 mm cutting length and a 6 mm shank diameter; the cylindrical shank with drive flat is compatible with standard collets and toolholders for stable mounting. Is this cutter suitable for high‑speed machining? The cobalt‑alloyed HSS‑Co grade offers improved red hardness compared with plain HSS, making the cutter suitable for elevated cutting speeds within the machine and process limits specified by the workshop. How does the DIN 850 D designation affect selection? DIN 850 D defines geometry and tolerances for this cutter type, aiding in predictable performance and compatibility with existing fixtures and process documentation; selecting a cutter to this standard reduces setup variability. How many flutes does the cutter have and what is the benefit? With 6 flutes, the cutter balances chip evacuation and surface finish, reducing vibration and improving dimensional stability during slotting operations. Manufacturer: ALPEN‑MAYKESTAG GmbH; Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com