110mm 16 x 10mm Grooving Tool Carbide P25/P30 4mm Cut Width, DIN 4981 (ISO 7) - Werner Wilke Zerspanungstechnik GmbH
Take advantage of the combination of industrial-grade Hartmetall P25/P30, standardised mounting and a compact 4 mm parting width for consistent, repeatable separations. Order the tool directly via Metav Werkzeuge or consult the team for application-specific guidance. Parting and Grooving Tool DIN 4981 (ISO 7) — 16 x 10 mm, Hartmetall P25/P30, right-hand (Wilke) A parting and grooving tool designed for precision turning and reliable chip control in standard ISO7 toolholders DIN 4981 (ISO 7) compatibility for standard mounting Carbide grade P25/P30 for general-purpose machining Steel shank with diamond-ground carbide inserts Compact 16 x 10 mm cross-section for stable clamping 4 mm cutting width for narrow parting operations Precise, repeatable parting with industrial carbide The tool delivers a reliable combination of die-hard carbide and standardised mounting, allowing stable, repeatable separations in turning processes. Built to DIN 4981 (ISO 7), the holder mates with commonly used toolposts and clamping systems; this reduces setup time and supports predictable tool height and alignment. The Hartmetall P25/P30 composition balances wear resistance with toughness, which is advantageous when working on a variety of ferrous components. The narrow cutting width results in reduced material removal per pass and improved surface finish at the cut face. Robust design for low-vibration performance and quick set-up A steel shank fitted with diamond-ground carbide cutting plates provides a rigid interface between the machine and the insert, minimising chatter and extending tool life. The 16 x 10 mm cross-section and 110 mm overall length offer a compact footprint that still provides necessary reach for many turning operations. The right-hand geometry suits conventional lathe set-ups and supports predictable chip flow away from the workpiece. This construction helps to keep cycle times steady and reduces rework, supporting efficient shop-floor throughput. Efficient use, predictable maintenance and application scope With an Einstechbreite (cutting width) of 4 mm, the tool is set up for narrow parting and grooving tasks where material waste must be controlled. The choice of P25/P30 carbide makes the tool a pragmatic option for general steel turning and typical workshop materials; its balanced wear resistance supports longer intervals between insert changes. Technical queries about compatibility or cutting data can be clarified quickly by the supplier; practical guidance helps to match cutting speeds and feeds to the carbide grade for best results. Contact Metav Werkzeuge today to discuss fitment, obtain cutting-data recommendations and secure reliable supplies of high-precision parting tools from stock in Emmerich Technical Data Article number: 4118645102NW Product type: Parting and grooving tool Norm: DIN 4981 (ISO 7) Label: Stechdrehmeißel DIN 4981ISO7 16x10mm HM P25/P30 re. Wilke Facts Overall length: 110 mm Cross-section: 16 x 10 mm Cutting width: 4 mm Packaging unit: 5 Special features Material: Hartmetall P25/P30 Right-hand cutting direction Steel shank with diamond-ground carbide inserts Compliant with DIN 4981 (ISO 7) FAQ Which machine types is this parting tool compatible with? The parting and grooving tool is compatible with lathes and turning centres that accept DIN 4981 (ISO 7) toolholders; compatibility is ensured by the standardised mounting system. What materials suit the Hartmetall P25/P30 grade best? The P25/P30 carbide grade is aimed at general-purpose turning of steels and similar ferrous materials where a balance of wear resistance and toughness is required. How wide is the cut this tool makes and what does that mean in practice? The tool offers a 4 mm cutting width, which is suitable for narrow parting and grooving tasks that demand minimal material removal and improved finish at the separated face. Is the tool supplied ready to fit or are inserts fitted on delivery? The item is supplied as a steel shank fitted with diamond-ground carbide cutting plates, ready for mounting in a compliant toolholder. Hersteller: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
12 x 8mm Grooving Tool Solid Carbide P25/P30, 3mm Cut Width, DIN 4981 (ISO 7) - Werner Wilke Zerspanungstechnik GmbH
Precision parting and grooving is provided by a right-hand carbide cutting system in P25/P30, featuring a compact 12 x 8 mm cross-section and a 3 mm grooving width for repeatable, narrow cuts; order directly via Metav Werkzeuge or consult our specialists for application guidance. Wilke Parting Tool DIN 4981 (ISO 7) — Carbide P25/P30, 12 x 8 mm, right-hand A Wilke parting tool designed for precision grooving and cut-off operations on standard lathes, compliant with DIN 4981 (ISO 7) and fitted with diamond-ground carbide inserts. Carbide P25/P30 cutting insert Cross-section 12 x 8 mm 3 mm grooving width for precise parting Precise, repeatable parting for production stability The compact geometry of the tool, with a 12 x 8 mm cross-section and a narrow 3 mm grooving width, delivers consistently reproducible cuts and minimal material loss per operation. Compliance with DIN 4981 (ISO 7) ensures compatibility with standard tool holders and reliable clamping, which helps maintain process stability across batches. This configuration reduces setup variability and supports predictable cycle times for series production. Long service life through balanced carbide technology Equipped with P25/P30 carbide, the insert offers a balanced combination of hardness and toughness suitable for general turning and parting tasks. The grade provides resistance to abrasive wear while preserving edge stability during intermittent cuts, contributing to longer tool life and fewer indexings. For workshops seeking dependable performance, the carbide composition reduces unplanned downtime and supports consistent surface quality at the cut face. Straightforward mounting and rigid support reduces vibration A steel shank fitted with diamond-ground carbide inserts ensures accurate locating and secure clamping in standard parting tool holders. The modest 100 mm overall length is compatible with compact setups and provides sufficient overhang control to limit chatter. The robust mechanical connection simplifies tool changes and improves vibration damping, which benefits finish quality and dimensional accuracy in precision operations. Ready for conventional lathe applications and tight grooves With a right-hand cutting direction and a focused insert geometry, the tool is optimised for conventional parting and grooving where narrow kerfs are required. Delivered in a practical packaging unit, the set-up supports efficient stock management for workshops carrying out repetitive cut-off tasks. The configuration is particularly useful when space on the lathe carriage is limited and when clean separation of workpieces is essential. For tailored advice on integrating this Wilke parting tool into existing tool holders or production lines, contact Metav Werkzeuge for expert guidance and prompt delivery from Emmerich: +49 2822 7131930, info@metav-werkzeuge.com Technical data Article number: 4118645052NW Description: Parting tool DIN 4981 (ISO 7), 12 x 8 mm, HM P25/P30, right-hand Manufacturer: Werner Wilke Zerspanungstechnik GmbH Packaging unit: 5 pieces Facts Overall length: 100 mm Cross-section: 12 x 8 mm Grooving width: 3 mm Applicable standard: DIN 4981 (ISO 7) Special features Carbide: P25/P30 Steel shank with diamond-ground carbide inserts Right-hand cutting direction Suitable for precision parting and grooving operations FAQ What material is the insert made from? The insert is manufactured from P25/P30 carbide as specified for the Wilke parting tool (SKU 4118645052NW), offering a balance of wear resistance and edge stability. What grooving width does the tool provide? The tool provides a 3 mm grooving width, designed for narrow kerfs and precise parting operations in conventional lathe work. Which standard and holder compatibility apply? The tool conforms to DIN 4981 (ISO 7), ensuring compatibility with standard parting tool holders that accept this interface. How long is the tool and what is the cross-section? Overall length is 100 mm with a 12 x 8 mm cross-section, offering a compact profile for reduced overhang and improved rigidity. Is the cutting direction left- or right-hand? This version is right-hand cutting, optimised for conventional right-hand parting and grooving applications. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
12 x 8mm Parting Tool Solid Carbide P25/P30 3mm Cut Left DIN 4981 (ISO 7) - Werner Wilke Zerspanungstechnik GmbH
Benefit from a robust combination of carbide P25/P30 cutting edges, a standardised DIN 4981 (ISO 7) interface and a slim 3 mm parting width for reproducible, efficient separations in small-batch and series production. Order the parting tool directly via Metav Werkzeuge or consult the team for application advice. Parting tool DIN 4981 (ISO 7) — 12 x 8 mm, carbide P25/P30, left-hand (Wilke) A Wilke parting tool designed for precise cut-off operations in constrained setups, featuring a 12 x 8 mm shank and diamond-ground carbide inserts Solid carbide grade P25/P30 inserts DIN 4981 (ISO 7) interface standard 12 x 8 mm cross-section steel shank Left-hand cutting direction 3 mm parting width for narrow grooves Precision and wear resistance for repeatable cut-off operations This parting solution combines carbide P25/P30 cutting edges with diamond-ground seating to deliver consistent edge geometry and extended life. The hardened insert geometry reduces micro-chipping and maintains cutting geometry over multiple regrinds, which results in more predictable tool life and fewer machine stoppages. For production environments where reproducibility matters, the standardised DIN 4981 (ISO 7) interface ensures straightforward mounting and exchangeability in compatible toolholders, supporting steady cycle times and lower setup overhead. Narrow cutting width with controlled chip formation The 3 mm parting width offers narrow-groove capability while preserving stability thanks to the 12 x 8 mm shank profile and robust insert fixation. The diamond-ground seating improves thermal contact and reduces insert movement, which helps control chip evacuation and surface finish in the parted component. Such features make this design suitable for applications requiring compact separation cuts and a good balance between stiffness and accessibility in restricted tool pockets. Compatibility and functional design for workshop workflows With a 12 x 8 mm cross-section and a left-hand cutting configuration, the tool is compatible with holders that accept DIN 4981 (ISO 7)-mounted inserts and simplifies tool change routines on conventional lathes and automated turning centres. The steel shank fitted with diamond-ground carbide inserts provides mechanical stability and repeatable positioning, which shortens calibration cycles and supports inline quality control. Left-hand orientation is pre‑set for operations that demand cut direction consistency without additional fixturing. Reliable supply and practical handling for production use Delivered in a practical packaging unit, the tool set supports efficient stock rotation and predictable replenishment for production shops. The combination of a standardised interface, clearly specified shank dimensions and a defined parting width reduces procurement complexity and supports centralised tool management. As a result, maintenance intervals can be planned more reliably and tool inventories kept leaner without compromising availability. For tailored specification advice or to secure a reliable supply of this Wilke parting tool, contact Metav Werkzeuge GmbH at info@metav-werkzeuge.com or call +49 2822 7131930 for fast, localised service from Emmerich. Technical data Article number: 4118645502NW Designation: Parting tool (Stechdrehmeißel) Material: Carbide P25/P30 Standard: DIN 4981 (ISO 7) Facts Overall length: 100 mm Cross-section: 12 x 8 mm Parting width: 3 mm Packaging unit: 5 pieces Special features Steel shank fitted with diamond-ground carbide inserts Left-hand cutting direction Interface: DIN 4981 (ISO 7) FAQ What interface does this parting tool use? The tool uses the DIN 4981 (ISO 7) interface, allowing mounting in standard holders that accept ISO 7-mounted parting inserts. What is the specified parting width and how narrow are the cuts? The cutting width is 3 mm, designed for narrow-groove separations where a slim kerf is required. Which carbide grade is fitted and what does that mean? Fitted with carbide P25/P30 inserts, the tool combines wear resistance and edge stability suited to general turning and parting tasks that require predictable tool life. Is the tool supplied as a single item or in multipacks? The product is supplied in a packaging unit of 5 pieces, enabling simple stock replenishment for small workshops and production lines. What is the SKU for ordering or stock identification? The SKU for this item is 4118645502NW, which should be used for enquiries and reorders. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
125mm 20 x 12mm Grooving Turning Tool Carbide P25/P30 5mm Cut Right-Hand, DIN 4981 (ISO 7) - Werner Wilke Zerspanungstechnik GmbH
Take advantage of a compact, right-handed parting tool solution with diamond‑ground carbide cutting plates and a precise 5 mm cut‑off width to maintain reproducible separations — available through Metav Werkzeuge with expert advice for fast workshop supply. Parting tool DIN 4981 (ISO 7) 20 x 12 mm, Carbide P25/P30 — right‑handed, Werner Wilke Parting tool DIN 4981 (ISO 7) 20 x 12 mm, Carbide P25/P30 — right‑handed, Werner Wilke is a right‑handed cut‑off and grooving tool intended for lathe use, featuring diamond‑ground carbide plates mounted on a steel shank for consistent edge quality and reliable separation. Carbide P25/P30 cutting plates Precise 5 mm cut‑off width Cross‑section 20 x 12 mm for standard holders Diamond‑ground plates on steel shank Precision and stability for reproducible separations The right‑handed parting tool is engineered to give consistent separation performance in routine turning operations. The carbide P25/P30 plates deliver a stable cutting edge that resists premature wear, while the diamond‑ground finish on the plates improves seating accuracy and reduces micro‑vibrations during cutting. With a 5 mm cut‑off width, the tool provides controlled material removal for clean parting without unnecessary material loss, helping to reduce scrap and rework in repetitive production. Productivity benefits and predictable tool behaviour A combination of a robust steel shank and precision‑finished cutting plates supports steady machining conditions and simpler tool life planning. The standard DIN 4981 (ISO 7) interface and the 20 x 12 mm cross‑section make the tool readily compatible with common toolholders, which reduces set‑up time and minimises downtime between operations. The straightforward geometry promotes reliable chip control during short, decisive cut‑off passes, enabling smoother cycle times and a more economical workflow. Workshop compatibility and handling advantages The tool’s overall length of 125 mm and compact cross‑section simplify installation in constrained tool posts and allow close control of overhang. Supplied in a packaging unit of 5, the tool is suited to small batch replenishment or stocking for routine maintenance. Right‑handed cutting direction and clear specification of the 5 mm cut‑off width make process planning straightforward for operators and ensures compatibility with existing turning setups adhering to DIN 4981 (ISO 7). Delivered as a ready‑to‑fit unit, the tool streamlines tool change procedures and supports steady production flow. Contact Metav Werkzeuge for tailored advice and fast supply from Emmerich — specialists can confirm holder compatibility and delivery times to suit the workshop's needs. Technical data Article number: 4118645152NW Product type: Stechdrehmeißel Manufacturer: Werner Wilke Zerspanungstechnik GmbH Standard: DIN 4981 (ISO 7) Dimensions / Core data Cross‑section: 20 x 12 mm Overall length: 125 mm Cut‑off width: 5 mm Cutting direction: right‑handed Packaging unit: 5 Materials / Special features Material: Hard metal (carbide) P25/P30 Steel shank with diamond‑ground carbide cutting plates Right‑handed configuration Designed for DIN 4981 (ISO 7) toolholders FAQ What is the cut‑off width of this tool? The cut‑off width is 5 mm, as specified for the parting tool (Stechdrehmeißel). Which carbide grade is fitted to the cutting plates? The cutting plates are carbide P25/P30, providing a balance of toughness and wear resistance for general turning tasks. Is the tool right‑ or left‑handed? This item is right‑handed, suitable for operations that require a right‑hand cutting direction. What are the key dimensions to check for holder compatibility? Check the 20 x 12 mm cross‑section and the DIN 4981 (ISO 7) interface; the overall length is 125 mm for fitting considerations. How many pieces are supplied per unit? The packaging unit contains 5 tools. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
140mm 25x16mm Grooving Tool Carbide P25/P30 6mm Cut Width, DIN 4981 (ISO 7) - Werner Wilke Zerspanungstechnik GmbH
High-precision parting with robust carbide and standardised fitting ensures reliable production cycles; benefit from the combination of carbide P25/P30 cutting plates, a 25 x 16 mm cross-section and a precise 6 mm parting width for repeatable results. Order the tool directly via Metav Werkzeuge or request tailored advice from our consultants. Wilke parting tool (25 x 16 mm) – Carbide P25/P30, DIN 4981 (ISO 7) Wilke parting tool (25 x 16 mm) is a right-hand, carbide-equipped cut-off tool engineered for precise parting and grooving tasks in standard workshop turning applications Carbide P25/P30 grades for durability DIN 4981 (ISO 7) compatible mounting Diamond-ground carbide cutting plates 6 mm parting width, right-hand cut Precision cutting for consistent parting results The tool delivers repeatable, clean parting thanks to its standardised interface and premium cutting materials. The combination of DIN 4981 (ISO 7) compliance and a compact 25 x 16 mm cross-section ensures consistent seat and alignment in compatible holders, reducing runout and vibration. With the cutting edges made from carbide P25/P30, the insert maintains edge stability under typical lathe speeds, which translates into longer tool life and fewer interruptions in production. Engineered for productivity and surface quality A steel shank fitted with diamond-ground carbide cutting plates gives a stable connection between holder and insert while promoting improved surface finish on the parted face. The defined 6 mm parting width minimises material waste and simplifies process planning for narrow grooves. The right-hand cutting direction is optimised for conventional turning directions on most lathes, enabling efficient chip breakage and steady feed rates for short-cycle and batch operations. Compatibility, handling and best-practice use The tool’s standard interface simplifies integration into existing setups that accept DIN 4981 (ISO 7) tools and holders. With an overall length of 140 mm, the geometry supports secure clamping while reducing overhang where possible. For best results, secure the shank firmly, use appropriate coolant or lubrication for the material being machined, and avoid excessive overhang to preserve edge life. The straightforward design supports both occasional workshop use and higher-frequency production runs, offering a balance of accessibility and professional performance. For availability, compatibility checks or expert recommendations on Wilke parting tools, contact Metav Werkzeuge GmbH in Emmerich or request a customised proposal via info@metav-werkzeuge.com or +49 2822 7131930 Technical data SKU: 4118645202NW Label: Stechdrehmeißel DIN 4981ISO7 25x16mm HM P25/P30 re. Wilke Manufacturer: Werner Wilke Zerspanungstechnik GmbH Product type: Parting tool Standard: DIN 4981 (ISO 7) Material: Hartmetall P25/P30 UID: 4118645202NW Core dimensions Overall length: 140 mm Cross-section: 25 x 16 mm Parting width: 6 mm Packaging unit: 5 Special features Right-hand cutting direction Steel shank with diamond-ground carbide cutting plates Carbide grades: P25 / P30 Designed for standard DIN 4981 (ISO 7) holders FAQ What material are the cutting plates made of? The cutting plates are made of carbide P25/P30, offering a balance of wear resistance and toughness for general turning and parting operations with the Wilke parting tool (SKU 4118645202NW). Which standard does the tool mount to? The tool complies with DIN 4981 (ISO 7), ensuring compatibility with holders and tooling systems that accept this standard interface. What is the parting width and why does it matter? The parting width is 6 mm, which determines the kerf and influences material removal, chip formation and waste; narrower widths help reduce material loss and can simplify finishing operations. Is the tool suitable for automated batch production? The combination of a steel shank, diamond-ground carbide plates and standardised mounting makes this parting tool suitable for both workshop use and higher-frequency production, provided proper clamping and cooling are observed. How long is the tool and how does that affect mounting? The overall length is 140 mm; keeping overhang minimal and ensuring rigid clamping will help maintain precision and prolong cutting edge life. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
16 x 10mm Grooving Tool 4mm Cut Width Carbide P25/P30, DIN 4981 (ISO 7) - Werner Wilke Zerspanungstechnik GmbH
Take advantage of the combination of durable P25/P30 carbide tips, a secure 16 x 10 mm shank, and a precise 4 mm parting width for dependable parting operations; order the tool directly via Metav Werkzeuge or consult their specialists for application guidance. Werner Wilke parting-off tool 16 x 10 mm (left-hand) — Carbide P25/P30, DIN 4981 (ISO 7) The parting-off tool is a left-hand, carbide-tipped turning tool for precise parting and grooving on lathes, designed to fit holders compliant with DIN 4981 (ISO 7). Carbide P25/P30 cutting tips DIN 4981 (ISO 7) shank form Left-hand cutting direction 4 mm parting width Engineered for reliable, repeatable parting cuts This turning insert is built around P25/P30 carbide, a grade chosen for a balance of toughness and wear resistance that suits frequent parting operations. The 16 x 10 mm cross-section of the shank provides secure clamping in standard holders, while the adherence to DIN 4981 (ISO 7) ensures interchangeability and simple replacement in compatible tool posts. The 4 mm parting width is specified for narrow, accurate cut-off work, reducing material waste and helping maintain concentricity. For machine shops seeking predictable results, the combination of standardised shank dimensions and a proven carbide grade supports consistent process setup and efficient tool management. Longer service life and fewer machine interruptions Carbide tips in P25/P30 deliver reliable wear behaviour under interrupted cutting conditions typical of parting work. The tool's construction, featuring a steel shank fitted with diamond-ground carbide cutting plates, reduces the need for frequent re-grinding and keeps changeover times low. This directly contributes to higher machine uptime and a more favourable cost-per-part scenario. Where repeatability and minimised setup time are priorities, a dedicated parting solution such as this lowers the risk of unexpected rejects and supports continuous production runs with fewer manual interventions. Practical mounting and application advantages Compatibility with the DIN 4981 (ISO 7) standard simplifies selection of suitable tool holders and ensures a solid mechanical interface. The left-hand cutting direction is ideal for operations where material feed and lathe configuration require a counterclockwise cut; specifying the correct orientation avoids fixture adjustments and preserves thread or shoulder geometry adjacent to the cut-off point. The 16 x 10 mm cross-section also aids in resisting lateral forces during parting, helping to maintain cut stability and preventing chatter, even with brief interruptions in the cut. Where this tool performs best in the workshop This tool is suited to steel and general metal parting tasks on conventional and CNC lathes where narrow, precise cuts are required. The robust carbide plates perform well in standard turning applications and support short-cycle production as well as precision one-off jobs. For precision workshops and industrial users who value interchangeability and operative reliability, the combination of standard shank form, dedicated 4 mm parting width and P25/P30 carbide provides a practical balance of performance and versatility. For specialised materials or non-standard set-ups, professional consultation is available to match tool choice to the workpiece and machine characteristics. For reliable supply and application advice on this Werner Wilke parting-off tool, contact Metav Werkzeuge in Emmerich by email at info@metav-werkzeuge.com or by phone on +49 2822 7131930 to discuss specifications and delivery. Technical Data Article number: 4118645552NW Standard: DIN 4981 (ISO 7) Material: Carbide P25/P30 Product type: Parting-off tool Manufacturer: Werner Wilke Zerspanungstechnik GmbH Facts Cross-section: 16 x 10 mm Overall length: 110 mm Parting width: 4 mm Cutting direction: left-hand Packaging unit: 5 Special features Steel shank with diamond-ground carbide plates Suitable for standard DIN 4981 (ISO 7) holders Designed for narrow parting and grooving operations FAQ What standard does the shank conform to? The parting-off tool conforms to DIN 4981 (ISO 7), ensuring compatibility with holders built to the same standard. Which carbide grade is used on the cutting plates? The tool is fitted with P25/P30 carbide plates, chosen for a balance of toughness and wear resistance appropriate to parting work. What is the effective cutting width of the tool? The specified parting width is 4 mm, suitable for narrow cut-off operations that require precision and minimal material loss. Is the tool right- or left-hand oriented? This variant is left-hand, intended for applications where a left-hand cut direction is required by the lathe setup. How is the tool supplied and in what quantity? The article is supplied in a packaging unit of 5, facilitating straightforward replacement planning in production environments. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
20 x 12mm Parting Tool Carbide P25/P30 5mm Cut Width, DIN 4981 (ISO 7) - Werner Wilke Zerspanungstechnik GmbH
Take advantage of the combination of carbide P25/P30 durability, a 5 mm parting width and a rigid 20 x 12 mm shank for controlled, repeatable parting operations; order directly via Metav Werkzeuge or ask the technical consultants for application advice. Wilke Stechdrehmeißel (Parting Tool) 20 x 12 mm — HM P25/P30, left-hand The Stechdrehmeißel (parting tool) is designed for left-hand parting and grooving in lathe turning, featuring a robust 20 x 12 mm shank and diamond-ground carbide cutting plates for stable performance. Carbide grades P25/P30 for durability 5 mm parting width for precise cuts 20 x 12 mm shank, 125 mm overall length Left-hand cutting, DIN 4981 (ISO 7) compatibility Durable carbide for consistent cutting performance The tool uses Hartmetall P25/P30 inserts that combine wear resistance with a balanced toughness, reducing the frequency of insert changes and downtime. Diamond-ground cutting faces ensure a consistent cutting edge geometry, which improves surface finish and reduces micro-chipping during high-precision parting work. This results in fewer interruptions to the machining cycle and a measurable uplift in process stability when compared with generic-grade inserts. Compact, rigid design for accurate parting and groove control A 20 x 12 mm shank cross-section and an overall length of 125 mm provide the rigidity required for narrow 5 mm parting operations. The compact profile reduces deflection under load and supports accurate depth control, so operators benefit from cleaner cut-off points and reduced secondary finishing. Conformance to DIN 4981 (ISO 7) simplifies integration with compatible tool holders, ensuring straightforward mounting and repeatable set-up. Left-hand orientation and standard compatibility for flexible shop use The left-hand cutting orientation is suited to applications where tool approach and spindle rotation necessitate a leftward cutting direction; this is specified in the product designation to avoid setup errors. The parting blade is equipped on a steel shank with diamond-ground carbide plates, a configuration that balances economy with service life. For shops standardising tooling, the compliance with recognised norms streamlines inventory choices and reduces the need for bespoke holders. Practical handling and predictable maintenance Thanks to the replaceable carbide plates, maintenance focuses on quick insert swaps rather than full tool replacement, cutting service time and inventory waste. The tool’s geometry supports controlled chip formation at the specified 5 mm cutting width, reducing the chance of chip entanglement during parting. For complex or critical applications, Metav’s technical team can provide guidance on optimised cutting parameters and compatible tool holders to preserve tool life and part quality. Request tailored advice from Metav Werkzeuge for optimal deployment of the Wilke left-hand parting tool — Metav’s specialists can recommend holders, cutting parameters and delivery options from Emmerich Technical data Article number: 4118645602NW Label: Stechdrehmeißel DIN 4981ISO7 20x12mm HM P25/P30 li. Wilke Type: Stechdrehmeißel Manufacturer: Werner Wilke Zerspanungstechnik GmbH Standard: DIN 4981 (ISO 7) Core technical data Overall length: 125 mm Cross-section: 20 x 12 mm Parting width: 5 mm Packing unit: 5 Design & special features Material: Hartmetall P25/P30 Left-hand cutting direction Steel shank with diamond-ground carbide cutting plates Designed for parting and grooving in turning operations FAQ What does left-hand cutting mean for setup? Left-hand cutting indicates the tool is designed to cut when fed from right to left relative to the workpiece; the Wilke parting tool must be mounted accordingly to match spindle rotation and feed direction. How wide is the cutting slot produced by this tool? The tool provides a 5 mm parting width as specified; this dimension refers to the effective cut width produced by the carbide cutting plates. Which standard ensures holder compatibility? Compatibility is assured by DIN 4981 (ISO 7), which defines the tool-shank and holder interfaces relevant to this parting tool. What are the benefits of P25/P30 carbide grades? P25/P30 carbide grades offer a balance of wear resistance and toughness, delivering reliable edge life for interrupted cuts and the demands of parting operations. How is the tool maintained when inserts wear? The diamond-ground carbide plates are replaceable; worn plates are exchanged rather than replacing the entire shank, reducing maintenance time and material waste. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
25 x 16mm Grooving Tool Carbide P25/P30 6mm Cut Left DIN 4981 (ISO 7) - Werner Wilke Zerspanungstechnik GmbH
Take advantage of the combination of carbide P25/P30 durability, a 25 x 16 mm robust shank and a precise 6 mm parting width for consistent, high‑quality parting operations; order directly via Metav Werkzeuge or consult our advisers for application support. Parting tool DIN 4981 (ISO 7) — 25 x 16 mm, carbide P25/P30, left‑hand (Wilke) Parting tool DIN 4981 (ISO 7) — 25 x 16 mm, carbide P25/P30, left‑hand (Wilke) offers an industrial‑grade solution for controlled parting and grooving in turning operations across general workshop and production environments. Carbide grade P25/P30 for demanding turning Complies with DIN 4981 (ISO 7) interface 25 x 16 mm cross‑section, robust shank 6 mm parting width for precise cuts High reliability and repeatable accuracy for parting tasks The design targets repeatable results in batch and one‑off turning. With a carbide P25/P30 cutting configuration and a steel shank fitted with diamond‑ground carbide inserts, the tool offers stable edge retention and consistent cutting geometry. The adherence to DIN 4981 (ISO 7) ensures compatibility with standard toolholders, reducing setup time and enabling straightforward interchangeability in a production cell. These characteristics translate directly into higher uptime and fewer reworks when parting and grooving operations demand tight tolerances. Robust construction that supports efficient machining A substantial 25 x 16 mm cross‑section and an overall length of 140 mm provide the rigidity required for clean parting strokes, while the 6 mm parting width is tuned for narrow, material‑saving separations. The left‑hand cutting orientation suits applications where the tooling arrangement or spindle direction requires an inverse approach. Robust mechanical properties reduce chatter and deliver a superior surface finish compared with less rigid tools, contributing to faster cycle times and lower scrap rates on both small and medium series. Clear application advantages and material suitability The combination of P25/P30 carbide and diamond‑ground topography makes the tool particularly effective for steel and alloy turning where wear resistance and edge stability matter. The tool is suited for industrial workshops and specialist turning centres seeking a balance between tool life and finish quality. Where narrow parting widths and controlled chip formation are required, this configuration reduces the risk of workpiece pull‑out and supports safer separating operations, especially in automated or semi‑automated turning cells. Practical fit‑and‑use considerations for the workshop Compliance with the DIN 4981 (ISO 7) interface simplifies fixture planning and spare‑part logistics: the tool mounts into standard holders without modification. Packaged in units of five, the set‑supply approach supports predictable stock levels for maintenance teams. The left‑hand orientation and specified dimensions should be checked against existing toolholders and part programmes during setup; if necessary, consult technical documentation for holder clamping and overhang limits to preserve tool life and maintain process stability. For precise parting applications, contact Metav Werkzeuge for technical advice and availability via info@metav-werkzeuge.com or phone +49 2822 7131930 Technical data SKU: 4118645652NW Product type: Parting tool Material: Carbide P25/P30 Cross‑section: 25 x 16 mm Parting width: 6 mm Overall length: 140 mm Cutting direction: Left‑hand Standard: DIN 4981 (ISO 7) Packaging unit: 5 Facts Overall length: 140 mm Cross‑section: 25 x 16 mm Parting width: 6 mm Packaging unit: 5 pieces Special features Carbide P25/P30 cutting configuration Steel shank fitted with diamond‑ground carbide inserts Complies with DIN 4981 (ISO 7) Left‑hand cutting orientation FAQ What materials is this parting tool best suited for? The parting tool with carbide P25/P30 is optimised for steel and alloy turning, offering good wear resistance and edge stability for typical workshop steels. Is the tool compatible with standard DIN 4981 toolholders? Yes, compliance with DIN 4981 (ISO 7) means the tool is designed for use with standard holders that accept this interface size. What is the effective parting width and why does it matter? The specified 6 mm parting width provides a narrow kerf for material savings and reduced clamping forces while maintaining chip control during separation. How is the tool supplied and what is the SKU for reordering? The item is supplied in packaging units of five and is listed under SKU 4118645652NW for easy reordering. Which direction of cut does this tool use and when is that required? This is a left‑hand parting tool; it is used where the tool must cut towards the operator’s left or in setups that require inverse cutting orientation. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com