140mm 10x10mm Internal Thread Turning Tool Carbide P25/P30 60° Right-Hand WN283 - Werner Wilke Zerspanungstechnik GmbH
Benefit from durable carbide P25/P30 grades, a precise 60° thread profile and a robust 10 x 10 mm shank for dependable internal threading in series production. Order the internal thread turning tool directly via Metav Werkzeuge or consult the Metav advisors for application-specific recommendations. Internal thread turning tool 10 x 10 mm, carbide P25/P30, right-hand 60° — Wilke The Internal thread turning tool 10 x 10 mm (carbide P25/P30) is a right-hand, 60° profile tool intended for secure internal threading operations; it is mounted on a steel shank fitted with diamond-ground carbide cutting inserts for repeatable performance Carbide P25/P30 for consistent wear resistance 60° profile for standard metric threads 10 x 10 mm square shank, 140 mm overall length Steel shank with diamond-ground carbide inserts Consistent material selection for predictable tool life The combination of carbide P25/P30 grades and diamond-ground cutting faces provides a balance between toughness and hardness that suits a broad range of general-purpose threading tasks. The specified carbide grades are chosen to reduce flank wear while maintaining edge security under interrupted cuts. This results in fewer insert changes, improved process stability and a measurable reduction in unexpected downtime for repetitive internal threading cycles. Design that supports secure clamping and accurate thread form A 10 x 10 mm square shank with a 140 mm overall length offers straightforward mounting in standard internal-tool holders and provides sufficient reach for many bore depths. The 60° tip geometry produces a standard metric thread form and helps to maintain pitch accuracy when combined with correct feed settings. The steel shank construction with fixed, diamond-ground carbide inserts ensures concentricity and repeatability, supporting consistent dimensional results across serial parts. Practical guidance for machining and set-up The right-hand cutting orientation suits conventional lathe spindle rotation and standard turning programmes. When setting up the tool, ensure the insert seat is clean and clamped to the holder to preserve the diamond-ground insert finish and to prevent micro-movement that would affect thread quality. Appropriate feeds and spindle synchronisation produce the intended 60° profile; the tool’s configuration is engineered to simplify set-up and to deliver predictable cutting behaviour in routine workshop environments. Where this tool is most effective This threading tool is intended for internal thread production where a standard 60° profile is required and where stable repeatability is a priority. The tool’s construction makes it well suited to batch operations where tool life and dimensional consistency matter. The designation WN283 and the solid combination of carbide specification and insert finish emphasise suitability for industrial use where operators require a robust, easy-to-integrate threading solution Contact Metav Werkzeuge for tailored advice on integrating the Wilke internal thread turning tool WN283 (SKU 4118655052NW) into production or to request current availability via info@metav-werkzeuge.com or +49 2822 7131930 Technical Data Article number: 4118655052NW Norm: WN283 Product type: Internal thread turning tool Manufacturer: Werner Wilke Zerspanungstechnik GmbH Facts Overall length: 140 mm Cross-section: 10 x 10 mm Tip angle: 60° Cutting direction: right Packaging unit: 5 Special features Carbide P25/P30 Steel shank with diamond-ground carbide inserts Right-hand 60° profile FAQ What materials is this internal thread turning tool suitable for? The internal thread turning tool with carbide P25/P30 is intended for general-purpose internal threading; the carbide grades provide a compromise between hardness and toughness for common workshop materials. Is the tool supplied ready-mounted on the shank? The tool is delivered as a steel shank fitted with diamond-ground carbide cutting inserts according to the product specification and ready for clamping in a compatible internal-tool holder. What is the standard thread form produced by the tool? The tool produces a 60° thread form suitable for standard metric internal threads when set up with appropriate feed and spindle synchronisation. How should the tool be clamped for best results? Secure clamping of the 10 x 10 mm square shank in a rigid internal-tool holder is recommended to preserve concentricity and to maintain the diamond-ground finish of the carbide insert. What is the SKU and norm designation for ordering and reference? Reference WN283, SKU 4118655052NW for ordering and specification checks; this identifies the Wilke internal thread turning tool with carbide P25/P30. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
160mm Internal Thread Turning Insert 12x12mm Carbide P25/P30 60° Right-Hand WN283 - Werner Wilke Zerspanungstechnik GmbH
High precision for internal threads is ensured by the combination of solid carbide P25/P30 construction and a 12 x 12 mm cross-section, while the 60° profile and right-hand cutting direction guarantee compatibility with standard metric internal threads; order the WN283 tool via Metav Werkzeuge or request technical advice from their consultants. Internal thread turning tool 12 x 12 mm, solid carbide P25/P30, 60° — Wilke The internal thread turning tool 12 x 12 mm from Werner Wilke is a compact carbide-tipped tool designed for accurate internal threading in limited bores on conventional lathes Solid carbide P25/P30 for durable edges 12 x 12 mm cross-section for tight bores 60° profile for standard metric threads Right-hand cutting for conventional lathes Robust carbide grade for predictable cutting performance The tool is built with solid carbide P25/P30, a specification that combines wear resistance with stable cutting properties to support repeatable results in serial production. The chosen carbide grade and the precise edge geometry provide consistent chip formation and reduce the need for frequent regrinding, which translates into quieter toolroom cycles and fewer unscheduled tool changes. Stability under load is a key technical advantage for workshop environments focused on reproducible thread quality. Compact geometry that reaches confined bores With a 12 x 12 mm cross-section and an overall length of 160 mm, the design offers a compromise between rigidity and accessibility for internal threading tasks. The compact section reduces vibration in narrow bores while the length provides the reach necessary for deeper thread profiles. For machinists working on components with limited internal space, the geometry supports controlled tool engagement and improved surface finish, helping to maintain dimensional accuracy even in small or awkwardly positioned bores. Standard 60° profile and right-hand cutting for compatibility The 60° thread angle aligns with common metric and ISO thread forms, ensuring the tool is suitable for producing standard internal threads in a wide range of components. The right-hand cutting direction corresponds to typical lathe spindle rotation, simplifying setup on conventional turning centres. Identified as WN283, the cutter’s profile and orientation minimise setup complexity and help maintain thread form integrity across batches. Solid construction and precision-mounted cutting plates The tool combines a substantial steel shank with diamond-ground carbide cutting plates mounted to the holder, providing sharp, repeatable cutting edges and reliable seat stability. Diamond grinding of the plates enhances edge definition and contributes to consistent tool life. The assembly is suitable for routine workshop maintenance and offers clear traceability through the WN283 designation and article numbering, which aids stock management and reordering in industrial supply chains. For specification checks, availability of the Wilke WN283 internal thread turning tool or tailored application advice, contact Metav Werkzeuge by e‑mail at info@metav-werkzeuge.com or by phone at +49 2822 7131930 for prompt technical support and supply information Technical data Article number: 4118655102NW Name: Internal thread turning tool 12 x 12 mm, WN283 Product type: Internal thread turning tool Manufacturer: Werner Wilke Zerspanungstechnik GmbH Facts Overall length: 160 mm Cross-section: 12 x 12 mm Point angle: 60° Packaging unit: 5 pieces Special features Material: solid carbide P25/P30 Steel shank with diamond-ground carbide cutting plates Right-hand cutting direction WN283 designation FAQ What material is the tool made from? The Wilke internal thread turning tool is supplied with solid carbide P25/P30 plates mounted on a steel shank with diamond-ground cutting plates for defined edge geometry. Which thread profile is produced with this tool? The tool employs a 60° profile, suitable for standard metric internal threads and compatible with common ISO thread forms. Is the tool suitable for use in confined bores? Yes, the 12 x 12 mm cross-section combined with the 160 mm overall length provides access to compact internal bores while maintaining sufficient rigidity for accurate threading. How is the tool identified for reordering? This item is designated WN283 and listed under article number 4118655102NW, produced by Werner Wilke Zerspanungstechnik GmbH Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
16x16mm Internal Thread Turning Tool Carbide P25/P30 60° Right-Hand WN283 - Werner Wilke Zerspanungstechnik GmbH
Take advantage of the combination of carbide P25/P30 durability, a compact 16 x 16 mm cross-section and a precise 60° profile for reliable internal threading; order directly via Metav Werkzeuge or consult the technical team for application support. Internal thread turning tool 16x16 mm, carbide P25/P30, right-hand, 60° — Wilke A Internal thread turning tool 16x16 mm P25/P30 engineered for precise internal thread cutting in turning operations, suitable for repetitive workshop and light industrial use Carbide P25/P30 inserts for high wear resistance 16 x 16 mm square cross-section 60° thread angle for standard internal threads Right-hand cutting direction for conventional turning Consistent performance from premium carbide grades The choice of carbide P25/P30 offers a balance between toughness and hardness that benefits continuous machining processes. This grade resists abrasive wear while maintaining edge stability during interrupted cuts, which reduces the frequency of insert changes and supports longer uninterrupted production runs. The result is a lower total cost of operation through fewer tool changes and less machine downtime. Precise 60° profile for repeatable thread geometry A defined 60° tip angle provides the correct flank geometry for standard internal threads, ensuring thread form accuracy and improved mating with external threads. The controlled profile reduces the need for additional finishing passes and minimises the risk of rework, which is particularly valuable for components requiring consistent thread tolerance and surface finish across batches. Rigid holder geometry for secure clamping and stability The 16 x 16 mm square section combined with a steel shank and diamond-ground carbide cutting plates (as supplied) gives a stable tool assembly that resists vibration under load. The robust design supports higher cutting parameters where appropriate and simplifies tool positioning in the holder, translating directly into reproducible thread starts and improved dimensional stability on turned parts. Practical suitability and operational benefits With a total length of 180 mm and a right-hand cutting direction, this tool integrates easily into standard lathe setups for conventional internal threading tasks. Supplied in pack sizes of five, the tools allow preparations for serial production while keeping spare inserts accessible. The configured tool suits workshops aiming for dependable, repeatable threading without complex retooling. Contact Metav Werkzeuge for tailored application advice and to secure the Wilke carbide P25/P30 internal thread turning tool via info@metav-werkzeuge.com or +49 2822 7131930 Technical Data Article number: 4118655152NW Standard: WN283 Manufacturer: Werner Wilke Zerspanungstechnik GmbH Facts Total length: 180 mm Cross-section: 16 x 16 mm Tip angle: 60° Pack unit: 5 Special features Material: Carbide P25/P30 Right-hand cutting direction Steel shank with diamond-ground carbide cutting plates Execution: 60° profile FAQ Which materials are suitable for machining with this tool? The internal thread turning tool 16x16 mm P25/P30 is designed primarily for general steel applications and similar materials where carbide inserts of grade P25/P30 provide effective wear resistance. How does the 60° tip angle affect thread compatibility? A 60° tip angle corresponds to standard thread flank geometry, which ensures that threads produced with this tool match common metric and unified profiles when used with correct pitch and feed settings. Is the tool supplied ready-to-use in the holder configuration described? The tool arrives equipped with diamond-ground carbide cutting plates on a steel shank, allowing immediate mounting and use in compatible tool holders for internal threading operations. What advantages do carbide P25/P30 inserts provide over other grades? Carbide P25/P30 combines hardness and toughness suitable for repetitive turning tasks, extending tool life under typical workshop cutting conditions and reducing the need for frequent insert replacement. Can this tool be used for interrupted cuts or entry into previously machined bores? The robust shank and carbide inserts provide the stability needed for many interrupted cuts; however, machining parameters should be adjusted according to the specific workpiece material and bore condition. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
20x20mm Internal Thread Turning Tool Carbide P25/P30 60° Right-Hand WN283 - Werner Wilke Zerspanungstechnik GmbH
Take advantage of the combination of carbide P25/P30 cutting edges, a rigid 20 x 20 mm square shank and a 60° tip angle for reliable, repeatable internal thread turning; order directly via Metav Werkzeuge or consult the Metav team for compatibility and supply options. Internal thread turning tool WN283 — 20 x 20 mm, carbide P25/P30, 60° right-hand (Werner Wilke) A WN283 internal thread turning tool designed for precision internal 60° thread machining in turning applications, equipped with diamond-ground carbide cutting plates for consistent thread form. Carbide P25/P30 cutting insert 20 x 20 mm square shank 60° tip for standard thread profiles Right-hand cutting direction 210 mm overall length Precision threads with consistent profile quality The combination of P25/P30 carbide and diamond-ground cutting plates provides high dimensional stability and a defined cutting edge, which reduces the need for rework and ensures consistent 60° thread geometry. This construction supports reproducible results in series production and single-part manufacture alike. The hardened cutting plates are ground to form, so the tool maintains thread profile accuracy over repeated cuts, contributing to lower scrap rates and predictable cycle times. Rigid shank design for secure clamping and reduced vibration A 20 x 20 mm square shank and 210 mm overall length deliver the mechanical stiffness required for internal turning operations in conventional and CNC lathes. The robust shank reduces chatter and improves surface finish by maintaining tool position under load. As a result, tool life is extended and surface integrity of internal threads is improved, which benefits subsequent assembly and reduces downstream inspection effort. Straightforward integration into shop workflows Supplied to the WN283 standard and fitted on a steel shank, the tool is ready to be mounted in standard toolholders for immediate use. The right-hand cutting direction matches common turning setups, simplifying process planning and reducing setup time. Packaged in practical multiples, the tool supports predictable replenishment and keeps production moving without frequent procurement interruptions. Industrial reliability and procurement confidence Sourced from an experienced tooling specialist and offered through Metav's distribution, this tool is backed by a distribution network focused on dependable supply and quality filtering from Emmerich. Metav’s approach to democratising precision means access to a broad range of measurement and tooling products, with stable availability for workshops and industrial users. The combination of proven cutting materials and a stable supply chain supports both daily production demands and planned maintenance cycles. Contact Metav Werkzeuge for a consultation on how the WN283 internal thread turning tool fits into current tooling setups and to secure reliable supply from Emmerich. Technical data Article number: 4118655202NW Standard: WN283 Brand: Werner Wilke Zerspanungstechnik GmbH Product type: Internal thread turning tool Label: Innengewindedrehmeißel 20x20mm HM P25/P30 re. 60° Wilke Data Overall length: 210 mm Cross section: 20 x 20 mm Tip angle: 60° Cutting direction: right Packaging unit: 5 Materials and features Carbide P25/P30 Steel shank fitted with diamond-ground carbide cutting plates 60° configuration Right-hand operation FAQ What is the tip angle of this internal thread turning tool? The tool features a 60° tip angle, designed for standard internal 60° thread profiles. What are the shank dimensions and overall length? The shank measures 20 x 20 mm and the overall length is 210 mm, offering a balance of rigidity and reach. Which cutting material is used for the inserts? The tool is equipped with P25/P30 carbide cutting plates, diamond-ground for consistent edge geometry. Is this a right-hand or left-hand tool? This model is configured for right-hand cutting direction. How many pieces are supplied per packaging unit? The item is supplied in a packaging unit of 5. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
25x25mm Internal Thread Turning Tool Carbide P25/P30 60° Right-Hand WN283 - Werner Wilke Zerspanungstechnik GmbH
Take advantage of the combination of carbide P25/P30 durability, a 25 x 25 mm rigid cross-section, and a 60° profile for consistent internal thread quality; order via Metav Werkzeuge or contact the consultants for selection guidance. Internal thread turning tool WN283 — 25 x 25 mm, Carbide P25/P30, 60° right-hand (Wilke) A Internal thread turning tool WN283 engineered for machining internal metric threads in lathes and CNC turning centres, supplied with a steel shank and diamond-ground carbide cutting inserts. Carbide P25/P30 for reliable wear resistance 25 x 25 mm cross-section for rigid setup 60° profile angle for standard metric threads Right-hand orientation; diamond-ground inserts High-performance cutting with carbide inserts for repeatable results The tool is equipped with carbide P25/P30 cutting edges mounted on a steel shank, delivering a balance of toughness and wear resistance suitable for production environments. The use of diamond-ground inserts gives a defined cutting geometry that promotes stable chip formation and predictable tool life. As a result, shops can expect improved process stability and fewer interruptions from unplanned tool changes, which supports higher overall machine utilisation and a more efficient workflow. Secure internal thread form and dimensional accuracy With a 25 x 25 mm cross-section and a 60° profile, the design focuses on rigidity and correct thread geometry for standard metric threads. The larger cross-section increases radial stiffness in internal operations, reducing deflection during plunging and profile cutting. By preserving the correct profile angle and insert geometry, the tool helps maintain thread form tolerance and surface finish, which is particularly important when producing mating components and assemblies where thread fit is critical. Practical handling and economic operation in production The cartridge-style arrangement of carbide inserts on a hardened steel shank allows straightforward replacement of cutting edges, reducing downtime and consumable cost over time. The right-hand cutting direction aligns with common lathe setups and turning centres, enabling simple integration into existing tool posts and holders. For batch production, the combination of long shank length and standard cross-section supports consistent set-ups and fast changeovers, contributing to lower unit costs and a more reliable manufacturing schedule. Secure reliable internal threading with the Wilke WN283 — contact Metav Werkzeuge for tailored advice and dependable supply from Emmerich: info@metav-werkzeuge.com | +49 2822 7131930 Technical data Article number: 4118655252NW Norm: WN283 Label: Innengewindedrehmeißel 25x25mm HM P25/P30 re. 60° Wilke Manufacturer: Werner Wilke Zerspanungstechnik GmbH Facts Overall length: 250 mm Cross-section: 25 x 25 mm Tip angle: 60° Packaging unit: 1 Special features Material: Carbide P25/P30 Execution: 60° thread profile Cutting direction: Right-hand Steel shank with diamond-ground carbide inserts FAQ What is this tool intended for? The internal thread turning tool WN283 is designed for machining internal metric threads on lathes and CNC turning centres, providing a standard 60° profile for mating thread fits. Which cutting material is used on the inserts? The cutting edges are carbide P25/P30, presented as diamond-ground inserts mounted on a steel shank to combine edge stability with toughness. Is the tool right-hand or left-hand? This tool is supplied in a right-hand configuration for conventional turning operations. What shank size and length does the tool have? Shank cross-section is 25 x 25 mm with an overall length of 250 mm, suitable for holders that accept 25 x 25 profiles. Does the tool support standard metric thread profiles? Yes, the tool is configured for the 60° thread profile commonly used for metric internal threads. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com