12/20mm Keyway Block For Fixed Mounting, Suitable For M6 x 10, H2mm - AMF
Take advantage of precise fixture alignment and secure thread compatibility for stable clamping in mixed-slot machine tables; order directly via Metav Werkzeuge or consult the team for specification matching. T-slot nut No. 6322A — fixed-mount T-slot nut for 12/20 mm slots (AMF) The T-slot nut No. 6322A is a fixed-mount clamping component for machine tables and fixtures, designed for nominal T-slot widths of 12 mm and 20 mm and compatible with M6 x 10 fastenings. For 12 mm and 20 mm T-slots Compatible with M6 x 10 fasteners Designed for fixed mounting Secure clamping across machine and fixture slots The T-slot nut delivers a consistent mechanical interface where two different slot standards meet: a nominal 12 mm width on the machine side and 20 mm on the fixture side. This makes the component suitable for hybrid set-ups where adapters or stepped clamping rails are used. By matching the nominal slot dimensions, the element reduces lateral play and helps maintain repeatable positioning under load. The design supports conventional threaded fastenings and ensures that a standard M6 x 10 screw achieves the required clamp force without the need for special bolts or washers. Simple installation and compatibility benefits Installation is straightforward: the element accepts an M6 x 10 fastener and is intended for fixed mounting in the slot system, removing the need for complex alignment during assembly. Because the component is tailored to the two nominal slot widths, it provides mechanical compatibility between machine tables and dedicated fixturing plates. For procurement and system planning, the single-piece supply format simplifies stock keeping and allows planners to order the exact quantity required for assembly lines or jigs. Practical advantages for workshop and production use Using a dedicated T-slot nut that matches both machine and fixture slot dimensions reduces set-up time and minimises rework caused by ill-fitting clamping hardware. The part supports efficient tool changes and fixture swaps by providing a repeatable datum for clamping points. Where repeatability and minimised downtime are priorities, the component contributes to smoother production flow and predictable assembly outcomes, particularly in mixed-standard environments common in retrofit and modular fixturing. For reliable clamping in mixed-slot setups, order the AMF T-slot nut No. 6322A through Metav Werkzeuge and request specialist advice from the Metav team to ensure full compatibility with existing tables and fixtures. Technical data Article number: 4000833234NW SKU: 4000833234NW Type: Nr. 6322A Label: Nutenstein Nr.6322A Nennmaß der Nut 12/20mm z.Festmontage AMF Manufacturer: AMF Product type: T-slot nut Packaging unit: 1 UID: 4000833234NW Facts Nominal slot (machine): 12 mm Nominal slot (fixture): 20 mm Suitable for: M6 x 10 Special features Fixed-mount design Compatible with mixed slot standards (12 / 20 mm) Designed for standard M6 x 10 fastenings Supplied as single unit FAQ Which slot widths does this component fit? The T-slot nut No. 6322A fits nominal slot widths of 12 mm on the machine side and 20 mm on the fixture side, providing compatibility where both standards occur. What fastener size is required for mounting? Mounting requires an M6 x 10 fastener; the T-slot nut is designed to accept this standard metric screw for secure clamping. Is the T-slot nut intended for adjustable or fixed mounting? This variant is designed for fixed mounting, intended to be secured in place rather than used as a freely sliding T-slot nut. Can the part be used to bridge different fixture systems? Yes — because it addresses both 12 mm and 20 mm nominal slot dimensions, the component is suitable for bridging machine tables and fixture plates that use differing T-slot standards. How is the product supplied? The item is supplied as a single unit, allowing direct replacement or specific-count ordering for assembly needs. Manufacturer: AMF; Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
125mm 14mm T-Slot Screw M12 Grade 10.9 With Nut And Washer DIN 787 - AMF
Robust Grade 10.9 construction combined with an M12 metric thread and a 125 mm overall length ensures secure clamping in industrial machine tables; the bolt is supplied complete with nut and washer. Order this T‑slot fastening directly via Metav Werkzeuge or consult our advisers for application support. T-slot bolt DIN 787 – AMF | M12 thread, 14 mm T-slot, 125 mm overall length A T-slot bolt DIN 787 engineered for dependable fixture of workpieces and tooling in 14 mm T‑slot systems on machine tables and modular clamping equipment. High-strength grade 10.9 For 14 mm T-slot systems M12 metric thread Includes nut and washer Reliable clamping for demanding industrial applications This fastening solution delivers high tensile strength through its Grade 10.9 specification, making it suitable for repeated load cycles in production environments. Compliance with DIN 787 denotes its design for T‑slot use on machine tables and modular rigs; the profile engages the slot securely and resists rotation under tightening. The material and heat-treatment implied by the grade provide greater resistance to shear and tensile stress than standard bolts, which reduces the need for frequent replacements and supports continuous operation in workshops and production lines. Straightforward compatibility and quick installation Fitting is straightforward: the bolt is dimensioned for a 14 mm T‑slot, features an M12 thread and an overall length of 125 mm, and is supplied complete with a nut and washer for an immediate installation. The M12 metric thread enables the use of common torque settings and standard tooling, simplifying assembly and maintenance tasks. For technical enquiries about fitment, torque recommendations or slot geometry, Metav Werkzeuge offers direct support via email or telephone to assist with correct selection and safe use. Engineered quality and dependable supply chain Manufactured to the DIN standard under the AMF label, this T‑slot fastener reflects industrial production tolerances and traceability appropriate for professional workshops and OEM assembly. Packaged per unit for controlled release into assembly processes, the component supports a lean inventory strategy where reliability and predictable performance matter. Choosing components with clear standards and vendor backing helps maintain uptime and reduces the administrative overhead associated with non-conforming parts. Choose the AMF T‑slot bolt for secure, repeatable clamping and contact Metav Werkzeuge for precise product matching or purchasing from the Emmerich warehouse at Metav Werkzeuge; our consultants will advise on integration and supply logistics. Technical Data SKU: 4000833320NW Standard: DIN 787 Product: T-slot bolt Brand: AMF Label: T-slot bolt M12, 14 mm T-slot, L 125 mm, Grade 10.9, incl. nut and washer Key measurements T-slot width: 14 mm Thread: M12 Overall length: 125 mm Axite enrichment: A: 13.7; B: 75; E: 22; K: 8 Pack unit: 1 UID: 4000833320NW Special features Compliance with DIN 787 High-strength Grade 10.9 Includes nut and washer Designed for machine table T‑slot systems FAQ What T-slot width does this bolt require? The fastening is designed for a 14 mm T‑slot and engages securely when used in appropriately sized machine table slots. Which thread size is used on this T‑slot bolt? The product features an M12 metric thread suitable for standard tooling and torque settings. Does the delivery include fastening hardware? Yes, the T‑slot bolt is supplied with the matching nut and washer to allow immediate assembly. Is this component compliant with any standard? This AMF T‑slot bolt is specified to DIN 787, indicating its intended form and fit for T‑slot applications. Manufacturer: AMF; Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
125mm Clamping Iron For T-Slot 16+18mm, Suitable For M16/M18 - AMF
Take advantage of a robust T‑slot clamping solution that meets DIN 6314 standards and fits 16 + 18 mm T‑slots; the compact 125 mm length and 18 mm width enable precise, repeatable fixturing. Order directly via Metav Werkzeuge or consult the team for tailored mounting advice. AMF T-slot Clamping Bar (DIN 6314) — 125 mm for 16 + 18 mm T‑slots A AMF T-slot Clamping Bar (DIN 6314) for secure and repeatable workpiece clamping on machine tables with 16 mm and 18 mm T‑slots. DIN 6314 conformity for reliable compatibility Fits 16 + 18 mm T‑slots for universal clamping 125 mm overall length for compact setups Suitable for M16 and M18 fixation Secure, standardised clamping that reduces setup variance The DIN 6314 specification ensures a standardised interface between the clamping element and machine table, delivering consistent contact geometry and predictable clamping behaviour. With a compact 125 mm overall length and 18 mm nominal width, this clamping bar is designed to stabilise short to medium workpieces where a small footprint is required. The standard compliance simplifies fixture planning and reduces the need for bespoke adaptors, which in turn lowers setup time and increases repeatability on production or jobbing machines. Efficient integration with existing fixturing and bolts Compatibility with 16 + 18 mm T‑slots and thread sizes M16 / M18 enables direct use with common T‑slot bolts and clamping hardware, avoiding additional conversion parts. The geometry supports secure force transfer to the workpiece, helping to maintain machining accuracy under typical cutting loads. For operations that demand quick changeovers, the compact form factor allows fast repositioning, leading to improved throughput and fewer machine idle minutes while preserving machining stability. Compact design for versatile workshop use and predictable handling The clamping bar’s dimensions and adherence to DIN enable easy storage, handling and replacement planning within a standard workshop environment. Supplied in a single unit, the component is suitable for supplementing existing clamping kits or for targeted applications where a short, robust clamping element is required. Traceable identification via SKU and conformity markings supports inventory control and maintenance scheduling, ensuring consistent availability and diminished risk of mismatched parts. For tailored advice on integrating this DIN 6314 clamping bar into existing fixtures, contact Metav Werkzeuge for product guidance and reliable supply from Emmerich — email info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: 4000833005NW Standard: DIN 6314 Product type: T‑slot clamping bar Brand: AMF Facts Overall length: 125 mm Nominal width: 18 mm T‑slot compatibility: 16 + 18 mm Suitable for: M16, M18 fixation Packaging unit: 1 Special features Conforms to DIN 6314 Compact design for small fixtures Traceable SKU for inventory control Intended for machine table clamping applications FAQ What table slots does this clamping bar fit? The clamping bar is designed for 16 + 18 mm T‑slots, making it suitable for machine tables and fixtures that accept these standard slot widths. Which bolt sizes are compatible with this AMF clamping bar? Compatibility is stated for M16 and M18 fixation, allowing use with common T‑slot bolts and clamping hardware. What is the overall length and width of the clamping element? The component measures 125 mm in overall length with a nominal width of 18 mm, optimised for compact clamping arrangements. Does the product adhere to an industry standard? Yes — the clamping bar conforms to DIN 6314, ensuring standardised geometry and predictable interfacing with machine tables. How is the item supplied and identified? The item is supplied as a single unit and is listed under SKU 4000833005NW for inventory and ordering purposes. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
125mm Clamping Wedge T‑Slot 12/14/16mm For M12 M14, DIN 6316 - AMF
Reliable, standard-compliant clamping for T-slots 12, 14 and 16 mm combined with compatibility for M12 and M14 fastenings supports predictable set-up and secure holding in common clamping systems. Order the component directly via Metav Werkzeuge or consult Metav's specialists for matching parts and delivery options. Clamping wedge DIN 6316 (AMF) — for T-slots 12 / 14 / 16 mm, 125 mm length A Clamping wedge DIN 6316 intended for securing fixtures and workpieces in standard T-slots, suited to M12 and M14 fastenings. Standard DIN 6316 compliance Fits T-slots 12 / 14 / 16 mm Length 125 mm for deep engagement Compatible with M12 and M14 fixtures Consistent fit with standard T-slot systems The DIN 6316 designation guarantees a familiar interface with common clamping rails and tables, simplifying procurement and replacement planning. Designed for T-slots 12 / 14 / 16 mm, the component provides a standardised mating geometry that reduces variation between suppliers. For workshops that rely on repeatable fixtures, this results in fewer adjustments during set-up and a predictable clamping envelope that integrates with existing tooling. Secure hold that shortens set-up time By combining a compact profile with a 125 mm engagement length, the wedge delivers stable contact across the slot, improving clamp stability under lateral loads. The component’s compatibility with M12 and M14 fastenings means common bolts and studs can be used without special adaptors, enabling faster assembly and fewer inventory items. The result is reduced machine downtime and more efficient batch changes on the shop floor. Predictable procurement through norm conformity Conformity to DIN 6316 is a practical advantage for purchasing and maintenance: the specification describes geometric and functional expectations, so replacements and spare parts remain interoperable. For purchasing departments, this lowers the risk of mis-matching components and supports a leaner spare-part inventory. Documentation and parts lists benefit from the norm reference when planning long-term toolroom supplies. Practical workshop considerations and applications The compact design and standardised dimensions make the element suitable for a wide range of clamping tasks in general workshop and industrial settings where T-slot tables are used. The simple geometry supports straightforward cleaning and inspection during maintenance cycles. For customised clamping assemblies, the wedge functions as a reliable basic element that pairs with standard bolts and clamp bars to build robust fixture systems. For supply enquiries or assistance selecting compatible fixtures for the AMF clamping wedge, contact Metav Werkzeuge for tailored advice and reliable delivery from Emmerich Technical Data Article number: 4000833058NW Standard: DIN 6316 Designation: Clamping wedge for T-slots (Spanneisen), AMF SKU / UID: 4000833058NW Facts T-slot compatibility: 12, 14, 16 mm Width: 14 mm Total length: 125 mm Suitable for: M12, M14 Packaging unit: 1 Enrichment codes: Addition: A: 20; B2: 40; B3: 20; C: 16; E1: 44; E2: 40 Special features Conforms to DIN 6316 Designed for standard clamping systems Intended for workshop and industrial fixtures Brand: AMF FAQ What T-slot sizes does the clamping wedge support? The clamping wedge supports T-slots of 12, 14 and 16 mm, matching standard machining table profiles. Which bolt sizes are compatible with this clamping element? Compatible bolt sizes are M12 and M14, enabling use with common clamping hardware. How long is the component and what does that mean for clamping stability? The element has a total length of 125 mm, which provides extended engagement in the slot for improved lateral stability during machining. Is the product standardised and easy to replace with equivalents? Yes; the item conforms to DIN 6316, which makes it straightforward to find equivalent parts with compatible geometry and function. What is the SKU for ordering or reference? The SKU / UID for ordering is 4000833058NW (AMF clamping wedge). Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
125mm Fork Clamp Bar 14mm Slot For M12 M14 Clamping Screw, DIN 6315B - AMF
Take advantage of the DIN 6315B conformity and fork-style reliability for consistent, repeatable clamping. The 14 mm slot and 125 mm overall length provide secure seating and extended reach for standard clamping screws. Order the fork clamping wedge directly via Metav Werkzeuge or ask our consultants if needed. AMF Fork clamping wedge DIN 6315B (slot 14 mm, L 125 mm) The AMF fork clamping wedge DIN 6315B is a fork-design clamping wedge for workshop fixtures and vices, engineered to accept standard M12 and M14 clamping screws. DIN 6315B compliant fork design Compatible with clamping screws M12 and M14 14 mm slot width for secure seating 125 mm overall length for versatile clamping Stable fork design for predictable clamping results The fork-style construction delivers a consistent contact geometry that reduces lateral movement during tightening. Conformity with DIN 6315B means the part matches common fixture interfaces, helping to maintain repeatability across setups. The design focuses on straightforward mechanical function: fork engagement, screw tensioning and positive seating — all translated into reliable clamp behaviour in production environments. This section emphasises the measurable benefit of repeatable positioning and reduced rework. Compatibility with standard clamping screws and fixtures Specified for M12 and M14 clamping screws, the component integrates with widely used clamping hardware, simplifying parts procurement and replacement cycles. The 14 mm slot allows secure seating of the mating screw head or bolt, reducing the need for additional adaptors. For workshops standardising on metric screw sizes, this compatibility supports inventory rationalisation and faster changeovers between jobs. Practical dimensions that aid handling and reach The 125 mm overall length increases usable reach and offers added leverage when securing workpieces, especially in deeper or more crowded fixture assemblies. The compact yet extended format reduces the need for auxiliary extensions while preserving clearance for adjacent components. The item is identified as SKU 4000833023NW for ordering and stock reference; this simplifies reordering and traceability within procurement systems. For reliable fork-style clamping from AMF, contact Metav Werkzeuge in Emmerich for technical advice and fast fulfilment by phone +49 2822 7131930 or email info@metav-werkzeuge.com Technical Data Article number: 4000833023NW SKU / UID: 4000833023NW Product type: Clamping wedge Design: Fork design Standard: DIN 6315B Brand: AMF Packaging unit: 1 Facts Slot width: 14 mm Overall length: 125 mm Suitable for clamping screws: M12, M14 Axite enrichment: A: 25; B2: 38; B3: 12; B4: 6 Packaging unit: 1 Special features DIN 6315B conformity Fork-style clamping wedge For clamping screw M12 / M14 Workshop-ready geometry for fixtures Identified as SKU 4000833023NW FAQ Which clamping screws are compatible with the AMF fork clamping wedge? The AMF fork clamping wedge is designed for M12 and M14 clamping screws, providing a standard interface for common workshop hardware. Does this component fit fixtures built to DIN 6315B? Yes, the AMF fork clamping wedge complies with DIN 6315B, enabling it to mate with fixtures and fixtures components manufactured to that standard. What are the principal dimensions to verify before ordering? Key measurements are a 14 mm slot width and a 125 mm overall length; these determine seating compatibility and reach in the fixture assembly. Is the AMF fork clamping wedge suitable for use in tight assemblies? The fork geometry and 125 mm length are intended to increase reach while preserving clearance; however, final suitability depends on the specific fixture layout and clearance requirements — verify dimensions against the assembly. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
125mm Parallel Gauge Set Pair-Set Precision Ground 24 Pairs ±0.01 mm - AMF
Benefit from hardened, case‑stored precision and pairwise plan‑parallel finishing for reliable stackable shimming; order the AMF Parallel shim set directly via Metav Werkzeuge or consult the technical team for specification support. Parallel shim set No. 6348P - 125 by AMF — 24 pairs, 125 mm, case‑hardened The Parallel shim set No. 6348P - 125 is a precision shimming kit for exact height setting and gap compensation in jigs, fixtures and machine set‑up. Precision, pairwise ground and parallel Case‑hardened for lasting wear resistance 1 mm step coverage across the set Height tolerance IT5 ±0.01 mm Precision shimming for reproducible set‑up The AMF set delivers measured, repeatable results because each shim is pairwise ground and finished to be plan‑parallel. This manufacturing approach guarantees consistent contact surfaces when shims are stacked, so nominal build‑ups increase in exact increments. With a height tolerance of IT5 and a declared accuracy of ±0.01 mm, the kit supports fine adjustment tasks where micrometric control matters. The 1 mm step arrangement across the set simplifies calculation of cumulative heights, reducing trial‑and‑error and shortening set‑up time in series production or toolmaking. Durable construction and tidy storage for workshop use Components are case‑hardened, providing improved surface hardness and resistance to wear under repeated handling and clamping forces. The set is supplied in a protective wooden case, which keeps elements organised and prevents accidental mixing of pairs — a practical advantage for busy benches. Each shim measures 125 mm in length and the complete delivery contains 24 pairs, making the assortment suitable for a wide range of machine‑side and assembly tasks where stable, long‑term accuracy is required. Conformity, compatibility and operational benefits Manufactured with reference to DIN ISO 2768m, the shims offer standardised dimensional integrity and are suitable for integration into existing fixture systems and measurement routines. The clearly defined increments and traceable tolerance class help maintenance teams and quality departments to document adjustments and reproduce settings reliably. As a precision accessory for production and maintenance, the set reduces waste caused by incorrect shimming and supports efficient changeovers in both single‑piece flow and repetitive operations. Technical enquiries regarding suitability for specific applications are welcome. For hardened, high‑precision height setting, order the AMF Parallel shim set No. 6348P - 125 via Metav Werkzeuge or contact Metav Werkzeuge for tailored technical advice at info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: 4123321021NW Type: Nr. 6348P - 125 Brand: AMF Product: Parallel shim set Content: 24 pairs Facts Length: 125 mm Step increments: 1 mm Height tolerance: IT5 ±0.01 mm Standard: DIN ISO 2768m Special features Case‑hardened Pairwise plan‑parallel fine ground Wooden storage case Sets cover step range with 1 mm increments FAQ What is the stated height tolerance of the set? The AMF Parallel shim set No. 6348P - 125 is specified with a height tolerance of IT5 and a nominal tolerance of ±0.01 mm. How many shims are included and what are their dimensions? The delivery contains 24 pairs of parallel shims; each element is 125 mm long and arranged to cover heights in 1 mm increments across the set. Are the shims suitable for repeated clamping and fixture use? Yes — the shims are case‑hardened to improve surface durability, making the set appropriate for frequent handling and clamping operations in workshop environments. Is the finish suitable for stacking without introducing tilt? Pairwise plan‑parallel finishing ensures flat contact faces; this pairwise ground quality limits cumulative error when shims are stacked for height build‑up. Which standard governs the remaining dimensions of the set? Remaining dimensions and general tolerances are produced in accordance with DIN ISO 2768m for consistent integration into tooling and fixtures. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
125mm Stud Bolt DIN 6379 Heat Treated Grade 8.8, M16 Thread - AMF
Take advantage of a standardised fastener with proven tensile performance: the DIN 6379 specification combined with tempering to property class 8.8 delivers dependable strength for mechanical joints, while the M16 thread and 125 mm overall length ensure straightforward integration in existing assemblies – order directly via Metav Werkzeuge or consult their specialists for configuration and supply. Stud bolt DIN 6379 M16x125 mm, tempered to property class 8.8 (AMF) A Stud bolt DIN 6379 M16x125 mm engineered for high-strength fastening in mechanical and structural applications DIN 6379 standardised stud bolt Tempered to property class 8.8 for strength M16 thread with 125 mm overall length Hex width 19 mm for common spanners Dependable strength designed for repeated loading The stud adheres to DIN 6379, providing a verified basis for specification in production and maintenance documentation. Tempering to property class 8.8 means a defined yield and tensile strength suitable for many bolted connections where a balance of ductility and load capacity is required. This combination reduces the risk of premature failure under cyclical loads and supports predictable torque behaviour during assembly, delivering measurable improvements in joint reliability. Clear, measurable dimensions for quick assembly Precise sizing reduces assembly time and fitment errors: the component features an M16 threaded section and an overall length of 125 mm, with an across-flats width of 19 mm for commonly used wrenches. An indicated unthreaded section of b: 75 mm provides a controlled shank length for locating or shear applications, supporting consistent clamp lengths and enabling repeatable preload in bolted joints. These objective values simplify part selection and inventory management for workshops and maintenance teams. Versatile application and streamlined procurement Manufactured by AMF, the part is suitable for a wide range of mechanical assemblies where a robust threaded stud is required, from fixture construction to machine repairs. The combination of standard compliance and documented mechanical class helps integrate the component into quality-management systems and parts lists. For purchasing efficiency and supply reliability, Metav Werkzeuge offers centralised access to this and related fasteners, reducing supplier complexity while maintaining traceability and batch control. For tailored advice on AMF stud bolts (SKU 4000833274NW) and to ensure the right specification for critical joints, contact Metav Werkzeuge in Emmerich or request a technical consultation by phone or e-mail. Technical data Article number: 4000833274NW Designation: Stud bolt DIN 6379 M16x125 mm, tempered to property class 8.8 (AMF) Label: Stiftschraube DIN6379 M16x125mm vergütet auf 8.8 AMF Dimensions & thread Thread: M16 Overall length: 125 mm Width (across flats): 19 mm Unthreaded section b: 75 mm Packaging unit: 1 Special features Standard: DIN 6379 Property class: 8.8 (tempered) Brand: AMF SKU: 4000833274NW FAQ What mechanical class does this stud bolt meet? The stud bolt meets property class 8.8, indicating defined yield and tensile strength suitable for many structural and mechanical fastening tasks. Which standard governs the design of this fastener? The component is manufactured to DIN 6379, ensuring compatibility with engineering specifications that reference this German industrial standard. What are the key dimensions to check before ordering? Check the M16 thread, the 125 mm overall length and the across-flats width of 19 mm to ensure correct fitment for intended assemblies. Is there an unthreaded shank and how long is it? Yes, the product data indicates an unthreaded section b: 75 mm, which is useful for locating or shear-plane applications. Who is the supplier and how can this item be ordered? The SKU 4000833274NW identifies the AMF stud bolt; procurement and further consultation are available through Metav Werkzeuge for ordering and supply logistics. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
125mm Stud Bolt DIN 6379 Metric Fine Threaded Tempered Grade 8.8 - AMF
Take advantage of a high‑tensile, DIN‑compliant fastener: the M20 stud bolt, heat‑treated to property class 8.8 with an overall length of 125 mm ensures dependable clamping force and long service life; order directly via Metav Werkzeuge or consult the technical team for application advice. Stud bolt DIN 6379 M20×125, property class 8.8 — AMF The stud bolt DIN 6379 M20×125 is a heat‑treated, metric threaded fastener designed for secure mechanical joins in industrial and maintenance settings. Conforms to DIN 6379 standard Metric thread M20 for common assemblies Heat‑treated to property class 8.8 Overall length 125 mm for versatile use Consistent clamping performance for machinery assemblies The stud bolt is designed to deliver reliable clamping force where repeatable connections are required. Compliance with DIN 6379 establishes predictable geometries and tolerances, which supports consistent torque‑to‑preload behaviour in bolted joints. The M20 thread and property class 8.8 rating indicate a balance between tensile strength and ductility, reducing the risk of sudden brittle failure while enabling secure fixation under dynamic load. For procurement planners and maintenance engineers, these characteristics translate into predictable assembly behaviour and reduced rework. Simplified installation thanks to standard dimensions Standardised dimensions reduce complexity at the workbench and accelerate assembly cycles. The stud’s 125 mm overall length and thread specification match common nuts and clamping elements, enabling straightforward replacement in existing equipment without custom adaptations. A nominal width value of 27 mm supports compatibility with typical spanners and torque tools, so maintenance intervals can be completed faster and with conventional tooling. This dimensional clarity supports lean workshop processes and lowers downtime during repairs. Material treatment for durability under load The fastener is quenched and tempered to 8.8, providing strength suitable for many mechanical and structural applications while maintaining sufficient toughness. Heat treatment improves resistance to plastic deformation during tightening and service loads, which extends component life and maintains joint integrity. The construction ensures that the fastener sustains repeated assembly cycles and mechanical stresses common in industrial environments, offering a cost‑effective alternative to more exotic materials where extreme corrosion resistance or ultra‑high hardness are not required. Procurement and quality traceability for operations Specifying a fastener that adheres to established standards simplifies quality assurance. With the DIN reference and brand identification, batch traceability and conformity checks become straightforward steps in incoming inspection. The supplied packaging unit of 1 facilitates controlled stocking of critical spares, and the clear article identifier (SKU) supports efficient reordering and inventory management. Choosing a standardised stud from a recognised supplier minimises specification variance and supports uninterrupted production throughput. Contact Metav Werkzeuge for supply and specification support on AMF stud bolts conforming to DIN 6379 — available from our Emmerich warehouse; eMail: info@metav-werkzeuge.com | Tel: +49 2822 7131930 Technical Data Article number: 4000833283NW Brand: AMF Product type: Stud bolt Label: Stiftschraube DIN6379 M20x125mm vergütet auf 8.8 AMF Facts Standard: DIN 6379 Thread: M20 Overall length: 125 mm Width: 27 mm Packaging unit: 1 Special features Property class: 8.8 (quenched and tempered) SKU: 4000833283NW Intended use: industrial fastening and maintenance FAQ What standard does this stud bolt comply with? The stud bolt complies with DIN 6379, ensuring standardised dimensions and tolerances suitable for industrial assemblies. What is the tensile class of the fastener? The fastener is heat‑treated to property class 8.8, giving balanced tensile strength and toughness for general mechanical applications. Which thread and length are specified for this article? Thread is M20 and the overall length is 125 mm, matching common metric nuts and assembly requirements. Is the stud suitable for repeated disassembly and reassembly? Yes. The quenched and tempered 8.8 treatment improves resistance to deformation during tightening and reuse, so it is suitable for maintenance cycles. How is the product supplied for inventory purposes? The item is supplied in a packaging unit of 1, with SKU 4000833283NW for easy reordering and stock control. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
125mm Stud Screw DIN 6379 Heat Treated 10.9 M10 - AMF
High-strength fastening for critical assemblies: tempered to grade 10.9 and manufactured to DIN 6379 for predictable mechanical behaviour in industrial use. Order this stud bolt directly via Metav Werkzeuge or consult our specialists for selection and availability. AMF stud bolt DIN 6379 M10 x 125 mm, Grade 10.9 The AMF stud bolt DIN 6379 M10 x 125 mm is a tempered threaded stud intended for high-strength mechanical and structural fastenings in workshops and production environments. Tempered to grade 10.9 Conforms to DIN 6379 standard Thread size M10 x 125 mm Width across flats 13 mm Reliable high-strength performance for safety-critical joints Manufactured to a recognised metric strength class, the stud provides repeatable mechanical properties under load. The grade 10.9 heat treatment denotes quenched and tempered steel with elevated yield and tensile strength, which reduces deformation and the risk of thread failure in dynamic or heavily stressed assemblies. For procurement and maintenance planning, the combination of a standardised specification and robust material treatment enables long-term predictability and lowers the frequency of unscheduled replacements while ensuring component safety in machinery and structural fixtures. Standardised dimensions for efficient assembly and inspection Compliance with DIN 6379 and the metric thread M10 x 125 mm ensures interchangeability with existing fasteners and compatibility with standard tooling. The 13 mm width across flats simplifies torque application with common spanners and sockets, supporting consistent assembly practice and accurate torque control. Standard dimensions support streamlined inventory management and permit straightforward verification during quality control; inspection routines can rely on familiar reference values rather than bespoke measurements, improving throughput in production and maintenance operations. Consistent workshop durability and traceable supply Tempering to grade 10.9 delivers consistent hardness and mechanical characteristics that are suitable for bolted joints exposed to high loads. The fastener’s specification reduces uncertainty during design and replacement work, while the clear labelling and traceability—including SKU 4000833254NW—support orderly stock management and documentation. Where project specifications mandate standard-compliant fasteners, this stud offers a cost-effective, reliable choice that aligns with industrial quality requirements and the expectations of professional workshops. For reliable high-strength fastenings select the AMF stud bolt and contact Metav Werkzeuge in Emmerich for availability and specialist advice: info@metav-werkzeuge.com or +49 2822 7131930. Technical data Article number: 4000833254NW Description: Stud bolt, DIN 6379, tempered to 10.9 Manufacturer: AMF Packaging unit: 1 Dimensions & thread Thread: M10 Overall length: 125 mm Width across flats: 13 mm Materials & standards Strength class: 10.9 (quenched and tempered) Standard: DIN 6379 Identification: SKU 4000833254NW FAQ What does grade 10.9 mean for the stud’s performance? Grade 10.9 indicates a quenched and tempered steel fastener with elevated yield and tensile strength; the AMF stud bolt in grade 10.9 delivers higher load capacity and reduced risk of plastic deformation under heavy service loads. Is this fastener compatible with standard M10 nuts and tapped holes? Yes, the stud’s M10 x 125 mm thread matches standard metric M10 fastening elements and can be used with corresponding nuts and tapped holes specified for M10 threads. Can the stud be used in structural or machinery applications? The stud, produced to DIN 6379 and tempered to grade 10.9, is designed for mechanical and structural fastening where higher tensile strength and predictable behaviour are required. How is the stud identified in stock and documentation? The fastener is identified by SKU 4000833254NW and the designation Stud bolt, DIN 6379, M10 x 125 mm, tempered to 10.9, which assists in procurement and traceability. What tooling is recommended for installation? Assembly is facilitated by the 13 mm width across flats, permitting the use of standard sockets or spanners sized to that dimension for consistent torque application. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
125mm Stud Screw M12x125 Hardened 10.9 DIN 6379 - AMF
Take advantage of DIN 6379 conformity and property class 10.9 strength for secure, long-term assemblies; the M12 thread and 125 mm overall length enable reliable integration in deep or multi-layer joints. Order directly via Metav Werkzeuge or request advice from our consultants for specification matching. AMF Stud Bolt DIN 6379 – M12 x 125 mm, Property Class 10.9 The AMF Stud Bolt DIN 6379 is a hardened threaded stud designed for high‑strength industrial fastening and assembly applications. High tensile strength grade 10.9 Thread size M12 for standard fittings Overall length 125 mm for deep assemblies Conforms to DIN 6379 standard Secure fastening with measurable strength The component is manufactured and tempered to property class 10.9, which delivers high tensile strength and predictable elastic behaviour under load. Compliance with DIN 6379 ensures that the geometry and thread form meet established industrial tolerances, simplifying integration with standard nuts and mating components. This technical consistency reduces assembly rework and supports reliable load-bearing joints in machine construction and structural fastening. Compatibility that speeds up assembly A standard M12 thread combined with an overall length of 125 mm offers straightforward interchangeability with common fasteners and fixtures. The stud’s dimensions favour installations where depth and clamping length matter, enabling designers and fitters to calculate clamping forces and thread engagement with confidence. Clear, standardised specifications mean fewer bespoke parts, faster procurement cycles and reduced planning overhead on the shop floor. Traceability and practical supply for production Marked identification and the supplied article reference make stock control and reordering efficient; the item is supplied per packaging unit 1, suitable for precision replacement or single‑part assembly work. The robust mechanical properties and standardised form reduce the risk of premature failure, supporting uptime and predictable maintenance intervals. For workshops and production lines that rely on repeatable quality, this stud is a practical component to keep on the shelf. Contact Metav Werkzeuge for tailored procurement advice, specification confirmation and to secure the correct stud bolt for the application; call +49 2822 7131930 or e‑mail info@metav-werkzeuge.com Technical data Article number: 4000833261NW Standard: DIN 6379 Thread: M12 Overall length: 125 mm Width: 15 mm Facts Property class: 10.9 Packaging unit: 1 SKU: 4000833261NW Special features Tempered to property class 10.9 Conformity with DIN 6379 Addition: b: 75 Manufacturer: AMF FAQ What material strength does the stud provide? The stud is specified as tempered to property class 10.9, providing high tensile strength and reliable performance in load-bearing applications. Is the thread compatible with standard nuts and fittings? Yes, the M12 thread matches standard metric M12 nuts and components, allowing straightforward integration into common assemblies. What standard certifies the stud’s dimensions and tolerances? The stud conforms to DIN 6379, which governs the dimensions and thread form relevant to this type of threaded stud. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
125mm T-Nut Clamp For T-Nut 12+14+16mm, DIN 6314 - AMF
Benefit from a combination of DIN 6314 conformity, compatibility with 12/14/16 mm T‑slots and support for M12/M14 clamping hardware for dependable workstation clamping; order directly via Metav Werkzeuge or consult our specialists for tailored selection advice. AMF T‑slot clamp DIN 6314 – for T‑slots 12/14/16 mm, 125 mm length The AMF T‑slot clamp DIN 6314 is a robust clamping component designed to secure workpieces on machine tables and milling fixtures with standard T‑slots Compatible with T‑slots 12 / 14 / 16 mm 125 mm overall length for extended reach Compatible with M12 and M14 clamping bolts Reliable clamping across common T‑slot widths Conforming to DIN 6314, this T‑slot clamp delivers consistent positioning and repeatable clamping performance on standard machine tables. Compatibility with 12/14/16 mm slots reduces the variety of clamps required in a busy workshop, streamlining inventory and setup. The standardised form helps achieve precision in fixture builds, as the component mates cleanly with established table geometries and commonly used clamping elements. Where stability and reproducibility matter, the standard conformity is a practical guarantee of fit and function. Fast installation and secure hold with standard threads Designed for use with M12 and M14 fasteners, the clamp enables quick assembly and secure mechanical engagement without special adapters. A 125 mm overall length provides additional reach for deeper setups while maintaining a compact footprint for crowded jigs. The combination of familiar thread sizes and extended reach supports efficient cycle changes and reduces non‑productive time during machining operations. For workshop teams, this means fewer adjustments and a faster return to productive runs while retaining a reliable clamping force. Built for workshop resilience and broad workshop use The design suits routine production and jobbing environments where robust components are required for repeated use. Compatibility with standard clamping hardware makes the clamp a practical choice for retrofit fixtures as well as new setups. The component’s straightforward geometry allows easy inspection and replacement during maintenance intervals, supporting uptime and predictable process quality. For buyers seeking a dependable, standards‑based clamping element, this option balances flexibility and longevity while fitting seamlessly into established tooling systems. For specification advice, availability and ordering of the AMF T‑slot clamp, contact Metav Werkzeuge in Emmerich: info@metav-werkzeuge.com | +49 2822 7131930 — our technical team will assist with selection and delivery options Technical data Article number: 4000833004NW Product: T‑slot clamp (Spanneisen) Brand: AMF Standard: DIN 6314 Facts Overall length: 125 mm Width: 14 mm T‑slot compatibility: 12 / 14 / 16 mm Suitable for thread sizes: M12, M14 Packaging unit: 1 Special features Suitable for use with standard clamping bolts M12 and M14 Axite enrichment: Addition: A: 20; B2: 40; B3: 14; E1: 21; E2: 50 SKU / UID: 4000833004NW FAQ How does the clamp accommodate different T‑slot widths? The clamp is profiled for 12 / 14 / 16 mm T‑slots so it fits common machine tables; the DIN 6314 geometry ensures a correct seating across these widths. Is this clamp suitable for milling fixtures and machine tables? Yes — the AMF T‑slot clamp DIN 6314 is intended for securing workpieces on milling fixtures and machine tables where standardised clamping is required. Which fasteners are recommended with this clamp? Use M12 or M14 clamping bolts as specified; these thread sizes are supported to provide the required clamping force and compatibility. What is the overall length and when is it useful? The overall length is 125 mm, offering extended reach for deeper setups or when additional clearance is needed between the clamp and workpiece. Manufacturer: AMF; Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
125mm T-Slot Clamping Bar For T‑Nut 16+18, DIN 6316 - AMF
Reliable clamping performance and DIN 6316 conformity combine with compatibility for 16 + 18 mm T‑slots and a compact 125 mm length to deliver stable workholding for small fixtures and machining setups. Order directly via Metav Werkzeuge or contact the technical team for fit verification and supply details. Clamping bar AMF (DIN 6316) for T‑slot 16 + 18 mm, 125 mm length A robust clamping bar designed to secure workpieces in T‑slot tables with 16 and 18 mm grooves, offering standardised mounting and compact length for tight set‑ups. DIN 6316 compliance Fits T‑slots 16 and 18 mm Length 125 mm for compact clamping Suitable for M16 and M18 fastenings Secure, standardised clamping for repeatable setups The clamping bar conforms to DIN 6316, which ensures predictable geometry and repeatable positioning when used with matching T‑nuts and bolts. This standardisation reduces setup variation and supports consistent machining results; the direct consequence is fewer rejects and less rework. Compatibility with M16 and M18 fastening systems allows the clamping element to be integrated into common fixturing layouts without the need for custom adapters, improving process efficiency and throughput. Compact design that integrates with existing tables With a 125 mm overall length and suitability for 16 + 18 mm T‑slots, the component is intended for compact fixturing where space is limited but rigidity remains essential. The reduced footprint permits multiple clamping points on small workpieces and simplifies the arrangement of stop blocks and parallels. By using standard T‑slot interfaces and conventional fasteners, the clamping bar minimises the need for special tooling and keeps clamping procedures straightforward for production and repair tasks. Robust conformity and lower downtime through predictable behaviour Manufactured for reliable performance, the clamping element delivers consistent clamping force across cycles, which helps to avoid loosening and vibration-related issues during machining. Compliance with recognised standards supports quality assurance processes and makes inspection and replacement straightforward. The compact, standardised design also supports lean inventory strategies: the single‑piece spec reduces variant complexity and helps to maintain a smooth supply to the workshop bench. For reliable, standardised clamping that fits common T‑slot tables, contact Metav Werkzeuge for availability and technical advice — Metav Werkzeuge provides local stocking and expert guidance from Emmerich. Technical data Article number: 4000833059NW SKU / UID: 4000833059NW Designation: Clamping bar DIN 6316 for T‑slot 16 + 18 mm L 125 mm Facts Standard: DIN 6316 T‑slot width: 16 + 18 mm Length: 125 mm Width: 18 mm Suitable for: M16, M18 Packaging unit: 1 Special features Manufacturer: AMF Product type: Clamping bar Axite enrichment: Addition: A: 25; B2: 50; B3: 25; C: 20; E1: 51,5; E2: 40 FAQ Which table grooves are compatible with this clamping bar? The clamping bar is designed for 16 + 18 mm T‑slot grooves and works with standard T‑nuts specified for those widths. Can this component be used with M16 and M18 bolts? Yes, the clamping bar is suitable for fastening with M16 and M18 bolts, providing secure attachment to matching T‑nuts. Does the clamping bar meet an industry standard? The component is manufactured to DIN 6316, ensuring standardised dimensions and repeatable positioning in fixture assemblies. What is the overall length and typical application area? With an overall length of 125 mm, the clamping bar is ideal for compact fixturing and small‑format machining tables where space is restricted. Is this item supplied singly or in sets? The item is supplied as packaging unit 1, intended for single‑piece replacement or incremental fixture assembly. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
125mm T-Slot Screw M20 Grade 8.8 DIN 787, T-Nut 20mm – AMF
Take advantage of the proven combination of DIN 787 conformity, Grade 8.8 strength and precise M20 threading for reliable clamping in 20 mm T-slots; order the fastening element directly via Metav Werkzeuge or consult the Metav specialists for selection support. AMF T-slot screw (DIN 787) – 20 mm T-nut, M20, 125 mm, Grade 8.8 A AMF T-slot screw (DIN 787) designed for secure clamping in machine table T-slots and fixture systems, offering standardised dimensions and robust tensile properties. DIN 787 standardised T-slot screw Fits 20 mm T-slots M20 thread, 125 mm overall length Grade 8.8 high tensile strength Consistent clamping performance for production environments Manufactured to DIN 787, this T-slot fastening delivers a precise fit in machine table grooves and fixture plates. The combination of M20 thread and 125 mm overall length ensures reliable engagement and consistent clamp pressure for medium to heavy-duty applications. The Grade 8.8 designation indicates a high-tensile fastener that maintains preload under dynamic loads; this regularity reduces retightening intervals and supports predictable process performance. Clear specification for correct selection and assembly The defined geometry — matched to a 20 mm T-slot — simplifies component selection and reduces setup time. The coarse thread size (M20) enables secure torque transmission while the overall length provides necessary engagement depth for many jigs and workholding arrangements. For customers less familiar with standards, DIN 787 denotes standardised T-slot dimensions, meaning compatible counterparts from other manufacturers will align without modification, aiding interchangeability on workshop equipment. Practical advantages on the shop floor and in maintenance Using a standardised, high-strength fastener reduces downtime caused by incorrect or underspecified hardware. The fastener’s geometry supports straightforward installation with common torque tools; retention in the T-slot is immediate once positioned and tightened. For complex assemblies or unusual configurations, Metav’s product data and advisors can clarify whether the AMF T-slot screw matches exact fixture requirements and recommend complementary components to complete the clamping system. For secure and standard-compliant clamping elements, order the AMF T-slot screw via Metav Werkzeuge or contact Metav’s consultants at info@metav-werkzeuge.com / +49 2822 7131930 for tailored advice and supply options Technical data Article number: 4000603236NW Product: T-slot screw (T-Nutenschraube) Manufacturer: AMF Standard: DIN 787 Facts Thread: M20 T-slot width: 20 mm Overall length: 125 mm Pack quantity: 1 Addition: A: 19.7; B: 85; E: 32; K: 12 Special features Grade 8.8 tensile class Standardised T-slot geometry Designed for machine table and fixture clamping Axite enrichment dimensional values included FAQ What T-slot size does this screw fit? This screw is specified for a 20 mm T-slot, ensuring compatibility with standard 20 mm machine table grooves. What does Grade 8.8 mean for load capability? Grade 8.8 indicates a high-tensile steel fastener; the AMF T-slot screw therefore provides elevated strength and maintains preload under typical workshop loads. Is the fastener compliant with an industrial standard? Yes, the T-slot screw is manufactured to DIN 787, which standardises T-slot fastening geometry for interchangeability. Which thread and length are provided? The product features an M20 thread and an overall length of 125 mm, suitable for medium to heavy clamping engagements. Can the dimensional additions A, B, E and K be used for fixture planning? Yes, the listed additions (A: 19.7; B: 85; E: 32; K: 12) supply the key dimensions needed for precise fixture and component layout. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
12mm Hex Nut DIN 6331 M8 Threaded, Strength Class 10, SW13 - AMF
Take advantage of the combination of standard compliance, high tensile capacity and precision machining to secure reliable assemblies with minimal maintenance; order directly via Metav Werkzeuge or consult our specialists for specification support. Hexagon nut DIN 6331 M8 — AMF, strength class 10, 13 mm spanner A hexagon nut DIN 6331 M8 designed for high-strength fastening in industrial and mechanical assemblies, offering standard compatibility and a machined bearing surface for consistent torque transfer. DIN 6331 standard compliance M8 thread, strength class 10 13 mm spanner width, 14.4 mm across corners 12 mm overall height, pressed and milled finish Reliable clamping through recognised strength class A fastener specified to strength class 10 delivers higher tensile and shear capacity than common lower classes, which directly improves joint safety under dynamic loads. The M8 thread paired with the DIN 6331 specification ensures compatibility with standardised bolts and studs, simplifying procurement and reducing inventory complexity. For maintenance planners, this means fewer part variants to manage and more predictable performance in bolted joints. Precision faces for predictable torque and reduced loosening The combination of pressed and milled production steps provides flat bearing faces and tight geometry control, which improves contact between nut and mating surface. With a 13 mm spanner width and 14.4 mm across corners, the hexagon profile supports standard tooling and avoids slippage during assembly. The 12 mm overall height balances thread engagement with compact installation space, helping to maintain preload and reduce the risk of loosening in vibrating environments. Standard compatibility and practical application benefits Conformity to DIN 6331 makes this component suitable for machine building, jigs and fixtures, conveyor lines and general workshop assemblies where standard parts are required for interchangeability. The nut’s defined geometry and strength rating enable engineers to perform straightforward strength checks during design reviews and maintenance inspections, supporting predictable life-cycle planning and fewer unexpected failures. Specify AMF strength class 10 hexagon nuts via Metav Werkzeuge for robust, standardised fastening — contact our consultants for tailored technical advice and order coordination. Technical Data Article number: 4000833406NW Brand: AMF Product type: Hexagon nut Standard: DIN 6331 Label: Hexagon nut DIN 6331 M8 spanner 13 mm pressed and milled strength 10 AMF Facts Thread size: M8 Spanner width: 13 mm Across corners: 14.4 mm Overall height: 12 mm Packaging unit: 1 Special features Strength class 10 Pressed and milled faces Suits standard M8 bolts FAQ What does strength class 10 mean for load capacity? Strength class 10 indicates a high tensile rating for the nut; the AMF hexagon nut in this class is suitable where increased clamping force and resistance to shear are required. Is this nut compatible with standard M8 bolts and screws? Yes, the hexagon nut DIN 6331 M8 is designed to mate with standard M8 bolts and studs, ensuring interchangeability across industrial components. Which spanner size is recommended for assembly? A 13 mm spanner is specified for this hexagon nut; the across-corners dimension of 14.4 mm accommodates standard tooling without risk of slipping. Does the pressed and milled finish affect torque application? The pressed and milled faces provide flat, accurate contact surfaces that improve torque distribution and reduce the likelihood of loosening under vibration. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
12mm Hexagon Nut M8 SW13 Strength Class 10, DIN 6330B - AMF
Robust fastening with standard conformity and high load capacity: the DIN 6330B specification combined with strength class 10 delivers dependable connections, while the compact M8 thread and wrench size 13 mm simplify installation. Order the component directly via Metav Werkzeuge or consult their technical advisors for specification checks. Hexagon nut DIN 6330B M8 — strength class 10, SW 13 mm (AMF) A hexagon nut DIN 6330B M8 engineered for high-strength mechanical connections in industrial and workshop applications. Hexagon nut M8 to DIN 6330B Strength class 10 for high load capacity Wrench size 13 mm (SW 13) for standard tools Overall height 12 mm for standard assemblies Consistent high-strength performance for industrial assemblies The component is specified to strength class 10, which indicates elevated load-bearing capability compared with lower classes; this translates into improved joint reliability under dynamic and static loads. Conformity to DIN 6330B ensures dimensional consistency across batches, reducing variability during procurement and assembly. Fewer failures and longer service intervals result in lower downtime and predictable maintenance cycles, supporting efficient production workflows. Precise geometry speeds up installation and reduces errors Standardised dimensions — M8 thread, wrench size 13 mm, corner measure 14.4 and an overall height of 12 mm — allow the fastener to be used with common spanners and torque tools, reducing tool changes and assembly time. The compact geometry facilitates access in confined assemblies and ensures predictable clamping behaviour. Clear conformity to international norms simplifies parts lists and inventory planning for procurement departments and workshop managers. Traceability and practical procurement for workshop use Marked data such as the manufacturer code and SKU supports traceability in supply chains and quality control. The clear specification and compatibility with standard tool sizes make the item straightforward to stock as a replacement part or for series production. For complex requirements or verification of fit, Metav’s advisors can provide dimension checks and guidance on selection, enabling informed procurement decisions and reducing the risk of incorrect orders. For reliable, high-strength fastenings request the AMF hexagon nut M8 (SKU 4000833391NW) via Metav Werkzeuge—contact info@metav-werkzeuge.com or call +49 2822 7131930 for technical clarifications Technical data Article number: 4000833391NW Type: M8 Standard: DIN 6330B Product: Hexagon nut Manufacturer: AMF Item label: Sechskantmutter DIN 6330B M8 SW 13mm Festigkeit 10 AMF UID: 4000833391NW Facts Overall height: 12 mm Wrench size (SW): 13 mm Thread: M8 Corner measurement: 14.4 Packaging unit: 1 Strength class: 10 Special features Conforms to DIN 6330B Strength class 10 SW 13 compatibility Supplied by AMF FAQ What standard does this nut conform to? The hexagon nut conforms to DIN 6330B, ensuring standardised dimensions and interchangeability. What is the thread size and wrench size? Thread size is M8 and the compatible wrench size (SW) is 13 mm, recorded for quick tool selection. What is the strength classification of the fastener? This fastener is specified as strength class 10, indicating suitability for higher-load applications. What are the key dimensions to check during procurement? Key dimensions include overall height 12 mm, corner measurement 14.4 and M8 thread; these values support correct part matching. Which SKU should be ordered for this item? Order using SKU 4000833391NW to ensure the correct AMF hexagon nut is supplied. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
12mm T-Slot Clamping Screw Set M12 38-Piece Heat-Treated, Strength Class 8/10 - AMF
Take advantage of a robust combination of M12 thread compatibility, 12 mm T-slot fit and hardened components to ensure reliable clamping under repeated load; order the set directly via Metav Werkzeuge or consult the sales team for technical matching. AMF clamping screw set Nr. 6520 – 38-piece M12 set for 12 mm T-slots The AMF clamping screw set Nr. 6520 is a machine-table workholding kit designed for secure clamping in 12 mm T-slots on fixtures and milling tables. For 12 mm T-slots M12 threaded components All parts quenched and tempered Supplied in wooden case with hinged lid Secure clamping where it matters The set is engineered for dependable workholding on machine tables and modular fixtures. With M12 threads matched to a 12 mm T-slot, the kit provides consistent preload and repeatable positioning for medium to heavy machining tasks. The combination of standardised thread size and slot compatibility reduces set-up time and minimises the need for bespoke fasteners, supporting faster changeovers and steadier machining cycles. Built for high load and longevity All components are quenched and tempered, offering improved fatigue resistance and dimensional stability during repeated tightening cycles. The inclusion of strength class 8 and 10 parts means the hardware can tolerate higher tensile and shear loads compared with lower-grade fasteners, which supports safer clamping under increased cutting forces. This durability reduces replacement frequency and helps maintain consistent clamping performance over time. Organised kit for efficient workshop use Presented as a 38-piece assortment in a wooden case with hinged lid, the kit keeps components organised and accessible at the bench or in the toolroom. Clear arrangement and sturdy storage accelerate selection of the required part and protect the hardware from surface damage when transported. The compact case supports tidy workshop practices and helps maintain productivity by keeping essential clamping elements to hand. Compatibility, application and selection guidance The clamping kit suits general-purpose fixtures, machine-bed set-ups and modular fixturing systems that accept a 12 mm T-slot and M12 hardware. For specific machine tables or unusual slot profiles, the thread and slot combination should be checked before installation. The set is ideal where robust, standardised clamping is required and where organised storage reduces setup time and operational interruptions. Contact Metav Werkzeuge for tailored advice on the AMF clamping screw set Nr. 6520 and to confirm compatibility with specific machine tables; phone +49 2822 7131930 or eMail info@metav-werkzeuge.com Technical data Article number: 4000833381NW Type: Nr. 6520 Product: clamping screw set Manufacturer: AMF SKU: 4000833381NW Packaging unit: 1 Facts T-slot size: 12 mm Thread: M12 Content: 38 pieces Strength classes: 8 and 10 Special features For T-slots All parts quenched and tempered Supplied complete in wooden case with hinged lid FAQ What does the set contain? The AMF clamping screw set Nr. 6520 is supplied as a 38-piece kit intended to cover common clamping needs for machine tables; the SKU is 4000833381NW. Is this kit suitable for a 12 mm T-slot? Yes, the components are configured for use with a 12 mm T-slot and standard M12 clamping arrangements. Which thread size is included in the set? The kit contains M12 threaded clamping elements suitable for M12 tapped or bolted connections in fixtures. What is meant by strength class 8 and 10? Strength class 8 and 10 denote higher-grade fasteners with increased tensile and shear capability; the AMF set uses these classes to provide improved load capacity and longer service life under machining forces. Are the components hardened? All parts in the set are quenched and tempered, improving durability and resistance to wear during repeated clamping cycles. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
12mm T-Slot Nut DIN 508 10mm M8, Strength Class 10 - AMF
Take advantage of a compact, DIN‑compliant fastening solution that combines a low profile with a robust M8 thread and strength class 10, ensuring consistent clamping performance in standard 10 mm T‑slots — order via Metav Werkzeuge or consult the specialists for application advice. T-Nutenstein DIN 508 T-Nut 10mm M8 AMF — standard T-slot nut with M8 thread and 12 mm height The T-Nutenstein DIN 508 T-Nut 10mm M8 AMF is a DIN‑508 compliant T‑slot nut designed for secure clamping in 10 mm machine table slots and modular fixturing systems. DIN 508 standard fit for T-slot 10 mm M8 internal thread for common fixtures Strength class 10 for high clamping loads Compact 12 mm height for low-profile setups Consistent fit and repeatable clamping in standard T‑slots Compliance with DIN 508 guarantees a precise seating geometry for insertion into T-slot 10 mm profiles, reducing lateral play and enabling repeatable clamping cycles. The machined profile matches common machine table tolerances, so fixture alignment and repositioning run with minimal adjustment. The combination of the standardised form and the integrated M8 thread means compatibility with widely used bolts and clamping elements, simplifying procurement and reducing the variety of fasteners required on the shop floor. High load capacity where strength matters Specified as strength class 10, the component is intended for demanding clamping tasks where increased tensile and yield capacity are required. This elevated class reduces the risk of plastic deformation under higher clamping torques and contributes to longer service intervals in high‑cycle production. For operations that prioritise mechanical reliability, the higher property class delivers a rational performance advantage and supports stable machining conditions with predictable holding force. Rapid integration into existing fixtures and easy machining layout The 12 mm height and compact form factor allow installation into low‑profile setups and tight assemblies without sacrificing thread access. Detailed installation dimensions — A 9.7; E 15; K 6 — provide the necessary reference for CAD modelling and fixture design, enabling seamless integration into existing jigs and clamping systems. The internal M8 thread aligns with standard clamping bolts, which accelerates assembly time and reduces the need for specialised fasteners, delivering a clear efficiency benefit on the production line. Proven reliability and supply continuity for workshops As a standardised T‑slot fastener from AMF, the part supports steady sourcing strategies for production and toolrooms. Availability via Metav Werkzeuge links the component to a stable European supply chain and a broad product range, which helps consolidate procurement and lowers vendor complexity. The presence of a defined standard and clear dimensional data supports quality assurance processes and simplifies documentation for inspection and traceability in workshop environments. For secure, DIN‑compliant clamping select the AMF T‑slot nut and contact Metav Werkzeuge for stock status or technical clarification: info@metav-werkzeuge.com | +49 2822 7131930 Technical Data Article number: 4000833202NW UID: 4000833202NW Manufacturer: AMF Facts Height: 12 mm T-slot width: 10 mm Thread: M8 Addition: A 9.7; E 15; K 6 Strength class: 10 Packaging unit: 1 Special features Standard: DIN 508 Product type: T-slot nut SKU: 4000833202NW FAQ Which T-slot width does this nut fit? The AMF T‑slot nut is designed for a 10 mm T‑slot in accordance with DIN 508, providing the appropriate seating geometry for standard machine table slots. What thread size is provided in the nut? This T‑slot nut includes an M8 internal thread, matching common clamping bolts and fixture hardware used in workshop assemblies. What does strength class 10 mean for the application? Strength class 10 indicates a higher property class intended for elevated clamping forces; the AMF T‑slot nut rated as strength class 10 offers improved resistance to deformation under load compared with lower classes. Are detailed installation dimensions available for fixture design? Yes; the component data lists the addition values A 9.7; E 15; K 6, which serve as reference dimensions for CAD modelling and fixture layout when integrating the AMF T‑slot nut. Is this product standard compliant and suitable for repetitive clamping cycles? Manufactured to DIN 508, the T‑slot nut from AMF provides a standardised form that supports repeatable seating and reliable clamping performance across multiple cycles. Manufacturer: AMF; Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
12mm T-Slot Nut M8 DIN 508 14mm Height, Strength Class 10 - AMF
Take advantage of a DIN 508-compliant fastening solution that fits 12 mm T-slots and provides an M8 internal thread for standardised fixturing; its strength class 10 rating ensures robust clamping and consistent repeatability in production environments. Order directly via Metav Werkzeuge or consult the team for application guidance. T-slot nut (DIN 508) — 12 mm T-slot, M8 thread — AMF A T-slot nut (DIN 508) engineered for securing fixtures and components in standard 12 mm T-slots, suitable for workshop and industrial clamping applications. DIN 508 compliant T-slot nut Fits 12 mm T-slots M8 internal thread Strength class 10 for high clamping forces Reliable clamping in standard T-slots The DIN 508 conformity guarantees compatibility with industry-standard T-slotted tables and profiles, enabling repeatable fixturing without trial-and-error adaptations. Built to sit precisely in a 12 mm slot and accept an M8 fastener, this component simplifies setup and reduces downtime during tool changes or rework. The standardised interface means fixtures and clamps from different suppliers align predictably, improving throughput and lowering setup variability. Built for strength and consistent repeatability Specified as strength class 10, the design supports elevated clamping forces while maintaining a secure seat in the T-groove. The factory-provided geometry values — A: 11.7; E: 18; K: 7 — define the critical seating and engagement dimensions that influence load distribution and torque transfer. This measured approach to geometry ensures that each unit delivers consistent mechanical behaviour across repeated cycles, which is essential for high-volume or precision assembly processes. Quick integration into assembly and fixturing workflows With a compact profile and standard thread form, the part integrates easily into existing fixturing systems and tooling kits. Supplied in single units, the item is identified by SKU/UID 4000603160NW for straightforward procurement and inventory control. Where fast replacement or exact-match parts are required, the standardised specification streamlines purchasing and reduces the risk of incorrect components entering the production line. The component supports efficient production planning by removing ambiguity about compatibility with common clamps and bolts. For secure, standard-compliant fixturing choose AMF T-slot nuts — contact Metav Werkzeuge for expert advice and reliable supply from Emmerich: info@metav-werkzeuge.com or +49 2822 7131930 Technical data SKU / UID: 4000603160NW Label: T-Nutenstein (DIN 508) Werksnorm T-Nut 12mm M8 AMF Manufacturer: AMF Dimensions / Standards Height: 14 mm T-slot width: 12 mm Thread: M8 Standard: DIN 508 Packaging unit: 1 Features / Special values Strength class: 10 Addition: A: 11,7; E: 18; K: 7 Product type: T-slot nut FAQ What slot width does this T-slot nut fit? The T-slot nut is specified for 12 mm T-slots and accepts an M8 fastener, as shown in the product specification for the AMF T-slot nut (SKU 4000603160NW). Is the nut compliant with industry standards? Yes — the component is DIN 508 compliant, ensuring standardised dimensions and interchangeability with compatible fixture systems. What does strength class 10 mean for performance? Strength class 10 indicates the component is designed for higher clamping loads and improved resistance to yielding under torque, supporting more demanding assembly and machining tasks. What are the A, E and K values listed in the data? The values A: 11.7; E: 18; K: 7 are factory-specified geometry figures that define the seating and engagement dimensions of the part; they are used to verify fit and load distribution in fixturing designs. Is the material specified for this T-slot nut? The provided product data for the AMF T-slot nut (SKU 4000603160NW) does not specify the material; consult the manufacturer's technical datasheet for material confirmation and surface treatment details. Manufacturer: AMF / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
13-48mm Clamping Wedge for T-Slot 16mm with M16x125 Clamping Screw, 18mm Width - AMF
Take advantage of the combination of secure clamping, simple adjustability and a compact footprint for reliable fixturing in production and workshop environments; the compact M16 clamping screw, compatibility with T‑slot 16 mm and the adjustable clamp height 13–48 mm make repeatable set‑ups straightforward. Order the AMF Nr. 6314V clamping jaw directly via Metav Werkzeuge or ask our consultants if needed. Nr. 6314V Clamping Jaw — T‑slot 16 mm, adjustable height 13–48 mm (AMF) The Nr. 6314V clamping jaw is designed for machine tables and fixtures with a 16 mm T‑slot and provides a narrow 18 mm contact face for compact workholding in confined setups. Adjustable clamp height 13–48 mm Designed for T‑slot 16 mm Sturdy 18 mm clamp width Supplied with M16 x16 x125 screw Secure clamping for precise machining A compact clamping element with an M16 clamping screw delivers dependable holding force while the adjustable clamp height of 13–48 mm permits accommodation of varying workpiece thicknesses. This combination reduces re‑set times and minimises slippage during machining cycles, which improves process stability. The narrow contact profile maintains access to neighbouring operations and supports precise, repeatable workholding on assembly and milling tables. Quick integration into standard fixturing Fitting a 16 mm T‑slot is the core function of this clamping solution; the T‑slot 16 mm compatibility ensures plug‑and‑play alignment with common machine tables and fixture systems. The 125 mm overall length and compact 18 mm width balance reach and clearance, enabling rapid clamping without interfering with surrounding tooling. The supplied M16 x16 x125 clamping screw streamlines installation and avoids separate procurement of fasteners. Robust design that supports uptime and simple handling Built for repetitive use in workshop and light industrial environments, the component combines a straightforward geometry with proven thread size for predictable torque‑to‑holding results. The clamping jaw’s dimensions and included screw mean fewer separate parts to manage, supporting efficient inventory and faster set‑up. For unfamiliar terms: a T‑slot is the standard dovetail‑like track on machine tables that guides and locates clamping elements; the clamp height range denotes the vertical span the jaw can bridge between the table and the workpiece. For specification checks or to confirm fitment for a specific table or fixture, contact Metav Werkzeuge — our specialists will advise on the AMF Nr. 6314V clamping jaw and assist with supply and delivery from Emmerich; eMail: info@metav-werkzeuge.com or Tel: +49 2822 7131930 Technical Data Article number: 4000833074NW Type: Nr. 6314V Product: Clamping jaw Brand: AMF Packaging unit: 1 Dimensions & core data Clamping height: 13–48 mm T‑slot: 16 mm Width: 18 mm Thread: M16 Overall length: 125 mm Supplied screw: M16 x16 x125 mm A: 25 B2: 50 E1: 26 E2: 45 LS: 55 Special features Supplied clamping screw M16 x16 x125 mm Compatible with T‑slot 16 mm systems Compact 18 mm clamp face for tight setups Adjustable clamp height for variable workpiece thickness FAQ What T‑slot size does this clamping jaw require? The clamping jaw is designed for a T‑slot 16 mm and integrates directly with machine tables and fixtures using that slot dimension. Is a clamping screw included with the item? Yes, the delivery includes a M16 x16 x125 clamping screw for immediate installation with the AMF Nr. 6314V clamping jaw. What range of clamping heights is possible? The adjustable clamp height spans 13–48 mm, allowing the jaw to bridge a variety of workpiece thicknesses without additional spacers. Can this jaw be used in compact fixtures with limited lateral space? The narrow 18 mm clamp width and 125 mm overall length make it suitable for confined layouts where neighbouring clamps or tools are close. Are the dimensional values A, B2, E1, E2 and LS provided? Yes; the component’s auxiliary dimensions are: A: 25, B2: 50, E1: 26, E2: 45, LS: 55, which assist in precise fixture planning. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
130mm Clamp Jaw No. 6313K for T-Slot 16+18mm, Clamping Height 0-55mm - AMF
Combining a compact total length of 130 mm with compatibility for T‑slot 16 + 18 mm, this clamping jaw delivers flexible fixturing and a wide clamping height range of 0–55 mm for varied workpieces. Order the component directly via Metav Werkzeuge or consult our specialists for integration support. Nr. 6313K clamping jaw — T‑slot 16 + 18 mm, clamping height 0–55 mm (AMF) A Nr. 6313K clamping jaw engineered for secure fixture in standard machine table T‑slots, offering adaptable height adjustment and straightforward integration with M16 clamping hardware. Fits T‑slot 16 + 18 mm Clamping height 0–55 mm Compatible with M16 clamping studs Total length 130 mm Versatile T‑slot compatibility for faster set‑ups The design targets rapid adaptation to common machine tables: the jaw accepts both 16 mm and 18 mm T‑slots, enabling fewer tool changes and condensed set‑up times. For workshop planners, this reduces the need for multiple specialised jaws and simplifies inventory. The geometry is optimised for standard clamping studs, so the component integrates smoothly into existing fixturing systems and supports repeatable positioning with minimal rework. Secure clamping across a wide height range Variable clamping is delivered through a broad clamping height range (0–55 mm) and defined axial offset (B2: 56 mm) that allow reliable contact with irregular or stepped workpieces. This range ensures firm contact pressure while maintaining accessibility for machining operations. The controlled height span improves stability during cutting or milling, helping to reduce vibration and improve surface finish in serial or single‑piece production. Compact form and straightforward installation With a total length of 130 mm and a nominal width of 18 mm, the jaw offers a compact footprint without sacrificing clamping surface area. The compact dimensions suit congested fixtures and make it simple to replace or rearrange elements on a machine table. Compatibility with M16 clamping hardware means existing studs and screws can be reused, lowering procurement effort and shortening downtime during changeovers. For precise, reliable fixturing with AMF components, contact Metav Werkzeuge in Emmerich for tailored advice and supply: info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: 4000603003NW Model: Nr. 6313K Label: Spannpratze Nr.6313K Gr.18 f.T‑Nut 16+18mm Spann‑H.0‑55mm AMF Facts T‑slot compatibility: 16 + 18 mm Width: 18 mm Total length: 130 mm Clamping height H1: 0–55 mm Secondary height H2: 42–84 mm Axial offset B2: 56 mm Suitable for: M16 Special features Product type: clamping jaw Brand: AMF Packaging unit: 1 SKU: 4000603003NW FAQ Is the jaw suitable for both 16 mm and 18 mm T‑slots? Yes. The clamping jaw is designed for T‑slot 16 + 18 mm, allowing it to be used on machine tables with either slot size. What clamping height can be achieved with this component? The jaw supports a clamping height range of 0–55 mm, providing flexibility for a variety of workpiece profiles. Can existing M16 studs be used with this jaw? Compatibility with M16 clamping studs is specified, so existing M16 hardware can generally be used for installation. What are the key installation dimensions to check before fitting? Refer to the total length 130 mm, width 18 mm, and the axial offset B2: 56 mm to ensure correct fit and clearance in the fixture layout. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
13mm Ball Washer DIN 6319C For M12 Screws, Bore 13mm - AMF
Take advantage of the combination of DIN 6319C conformity, a precise Ø13 mm bore and compact height for consistent seating and reliable assemblies; order directly via Metav Werkzeuge or consult our technical team for specification support. Spherical washer DIN 6319C for M12 — AMF, bore Ø13 mm The Spherical washer DIN 6319C is a precision seating washer designed to compensate angular misalignment and ensure uniform load transfer beneath M12 fastenings in mechanical and structural assemblies DIN 6319C standardised seating washer For M12 fastenings with Ø13 mm bore Compact height H2 4.6 mm for tight spaces Spherical seating radius R 17 for self-alignment Secure seating and consistent load transfer The spherical washer manufactured to DIN 6319C provides a reliable bearing surface that compensates for angular errors between bolt head and component face. By matching the seating geometry to the mating surface, the washer improves load distribution across the joint and reduces peak stresses that can cause loosening or uneven clamping. For assemblies using M12 bolts, the specified Ø13 mm bore ensures correct running clearance while the spherical form promotes repeatable torque behaviour and safer mechanical connections. Engineered dimensions for predictable assembly performance Key measures such as D1 Ø13 mm, D3 24 mm, H2 4.6 mm and R 17 mm define the seating profile and overall fit. The bore diameter (D1) is selected to suit standard M12 shank tolerances; the outer diameter (D3) and spherical radius (R) determine contact area and tilting capacity. These dimensions translate directly into practical benefits: precise centring, consistent clamping force and reduced need for rework. Technical teams unfamiliar with seating washers will find that adherence to standard dimensions simplifies parts sourcing and ensures interchangeability across suppliers. Practical workshop advantages and supply reliability Delivered in single-unit packaging for controlled assembly usage, this seating disc supports quality-conscious production and maintenance workflows. The design reduces rework time and supports predictable assembly tolerances, which is particularly valuable for repeat production runs or retrofit work. For procurement and stocking, Metav Werkzeuge’s distribution from Emmerich acts as a quality filter for the European market, helping maintain steady supply and technical guidance for fitment and selection. For technical clarification or to source AMF spherical washers with DIN 6319C conformity via Metav Werkzeuge, contact our specialists in Emmerich for immediate assistance and order placement Technical data SKU: 4000833458NW Label: Kugelscheibe DIN 6319C for screws M12, bore Ø13 mm Manufacturer: AMF Product type: Spherical washer Suitable for: M12 Packaging unit: 1 UID: 4000833458NW Dimensions / Key measures D1: 13 mm (bore Ø) D3: 24 mm (outer Ø) H2: 4.6 mm (height) R: 17 mm (spherical radius) Standard: DIN 6319C Features / Applications Standardised seating element for angular compensation Designed for steel assemblies and machine construction Single-piece seating washer for consistent clamping Compact form factor for limited installation space FAQ Is this washer suitable for M12 bolts? The spherical washer is specified for use with M12 fastenings; the Ø13 mm bore provides the correct clearance for standard M12 shanks. Which standard does the seating washer comply with? The washer conforms to DIN 6319C, ensuring interchangeability and standardised seating geometry. What are the key dimensions that affect fit and function? Critical measures are D1 Ø13 mm, D3 24 mm, H2 4.6 mm and R 17 mm, which together define bore fitment, contact area and angular compensation. Can the washer compensate for uneven contact surfaces? Yes, the spherical seating radius allows the washer to correct minor misalignments between the bolt head and the mating surface, improving load distribution. How is the product supplied and identified? This item is supplied in a packaging unit of 1 and is listed under SKU 4000833458NW for ordering and inventory. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
13mm Clamping Wedge For T-Slot 12+14mm, Clamping Height 0-35mm - AMF
Take advantage of precise T‑slot compatibility and adjustable clamping height to standardise fixture setups and reduce changeover time; order the Clamping prong No. 6313K directly via Metav Werkzeuge or consult our specialists for integration advice. Clamping prong No. 6313K — compact clamping element for T‑slot fixtures The Clamping prong No. 6313K is a purpose‑built clamping element for machine tables with 12 mm and 14 mm T‑slots, engineered to deliver repeatable clamping at low profile heights. T‑slot compatible 12 + 14 mm Adjustable clamping height 0–35 mm Width 13 mm for narrow fixtures Suitable for M12 clamping bolts Faster, more repeatable setups with T‑slot compatibility The design offers direct compatibility with standard T‑slot 12 + 14 mm machine tables, which simplifies fixture planning and reduces the need for adapters. By matching the slot geometry, the clamping element provides consistent repeatability and reduces lateral play during clamping cycles. The compact footprint supports denser fixturing layouts without compromising access to the workpiece, so set‑up times are shortened and throughput is improved in repetitive production tasks. Secure clamping across a practical height range With an adjustable clamping height of 0–35 mm (H1), this clamping prong adapts to different workpiece thicknesses while maintaining a low profile. The additional dimension references (H2: 30–55 mm, B2: 38) indicate compatibility with common fixture stacks and spacer arrangements used in professional clamping systems. The part is engineered for use with M12 clamping bolts, ensuring secure axial force transmission and straightforward integration into existing clamps and tensioning elements. Robust, space‑saving form for workshop efficiency Constructed to operate reliably in demanding shop environments, the clamping element’s 13 mm width and overall compact length of 88 mm permit installation where space is limited. The narrow section and defined contact faces reduce interference with tool paths and fixturing accessories. Supplied as individual units (packaging unit 1), the component suits both one‑off jigs and serial fixture builds, enabling modular expansion of clamping systems without extensive redesign. Practical integration and application notes The clamp prong is a dedicated clamping aid for curvature‑free, mechanical clamping in metalworking and general workshop applications. It mates with standard clamping hardware; no special fasteners are required beyond the specified M12 bolts. For multi‑station fixtures, the compact design supports closer spacing of clamps, increasing usable table area and enhancing workpiece stability during machining operations. For tailored advice on integrating the AMF clamping prong into existing fixtures or to order delivery from Metav Werkzeuge, contact our technical team at info@metav-werkzeuge.com or call +49 2822 7131930 — Metav Werkzeuge provides expert support and reliable supply from Emmerich to your workshop Technical Data Article number: 4000603000NW Type: Nr. 6313K Product: Clamping prong Brand: AMF Dimensions & measurable data Width: 13 mm Overall length: 88 mm T‑slot compatibility: 12 + 14 mm Clamping height H1: 0–35 mm Additional dimension H2: 30–55 mm B2 value: 38 Suitable for: M12 Packaging unit: 1 UID: 4000603000NW Materials & features Product type: clamping element for T‑slot fixtures Supply format: single unit Intended use: mechanical clamping in workshop fixtures FAQ What T‑slot sizes does this clamping prong fit? The clamping prong is compatible with 12 mm and 14 mm T‑slots, designed to match standard table profiles for secure seating and repeatable positioning. Which clamping height range is usable with this item? The primary clamping height range is 0–35 mm (H1); further dimension references (H2: 30–55 mm, B2: 38) describe additional stack options for fixture assemblies. Which bolt size is recommended for fastening? The component is designed for use with M12 clamping bolts to provide correct axial force and integration with common clamping hardware. Is the prong suitable for dense fixture layouts? Yes, with a 13 mm width and 88 mm overall length, the element is suitable for compact fixturing where space conservation is critical. Can the prong be used in serial production fixtures? Supplied as single units, the prong is intended for modular use and can be deployed in both single‑jig and serial fixture environments to improve process stability. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
13mm Flat Washer DIN 6340 For M12 Screws, 35mm Outer Diameter x 5mm Thick - AMF
Take advantage of a standardised fastening solution that ensures consistent load distribution and straightforward inventory management: the washer is manufactured to DIN 6340, sized for M12 fastenings with a 13 mm bore and a 5 mm thickness, delivering reliable performance in assembly processes. Order the part directly via Metav Werkzeuge or consult our specialists for compatibility checks. U-washer DIN 6340 for M12 screws, 13 mm bore — AMF The U-washer DIN 6340 is a standard-compliant washer designed to distribute clamping loads for M12 fastenings in industrial and workshop assemblies. Standardised to DIN 6340 Suitable for M12 fastenings 13 mm bore for precise fit 5 mm thickness for stable support Consistent assembly results through standard compliance Conformity with DIN 6340 ensures consistent geometry and repeatable behaviour in series assembly, which reduces variability during torqueing and joint pre-loading. The standardised inner diameter of 13 mm corresponds to the nominal thread size, so the bore clears M12 threads without play that would compromise clamping. Where process reliability is required, such as in fixture building or machine assembly, the standard designation provides a clear basis for procurement and quality control. The item is listed under SKU 4000833438NW for traceability in stock systems. Mechanical benefits from defined dimensions A washer with an outer diameter of 35 mm and a thickness of 5 mm gives a predictable contact area and stiffness under load; this translates into reduced localised material deformation and improved joint life compared with undersized washers. The specified thickness helps prevent subsidence under high compression and keeps the clamped parts aligned. In practical terms, using a washer of the stated dimensions supports consistent clamp force transmission and lowers the risk of fastener loosening in dynamic or thermal cycling environments. Practical handling and workshop integration The component is intended for straightforward stocking and use in maintenance and production settings. Supplied in single units, the part can be logged into inventory systems and matched to M12 bolt assortments or fitting kits. As a basic fastening element, it integrates with established assembly routines and can be combined with standard nuts and bolts without additional adjustments. For technicians less familiar with specification sheets: the bore is the central hole size, the outer diameter indicates the load-bearing ring, and the thickness relates to the washer’s stiffness — these three parameters together determine fit and performance. Contact Metav Werkzeuge for supply and technical advice on AMF U-washers; call +49 2822 7131930 or email info@metav-werkzeuge.com for delivery from Emmerich and assistance with application suitability Technical data Article number: 4000833438NW Label: U-Scheibe DIN 6340 f.Schrauben M12 Bohrungs-D.13mm AMF Manufacturer: AMF Product type: Washer Suitable for: M12 Packaging unit: 1 Numeric data Bore diameter D1: 13 mm Outer diameter D2: 35 mm Thickness S: 5 mm Standard: DIN 6340 Special features Standard-compliant geometry Designed for load distribution in M12 joints Single-unit packaging for inventory control FAQ Is this washer suitable for M12 bolts? Yes. The washer is specified for M12 fastenings and features a 13 mm bore matched to that thread size. What does DIN 6340 mean for performance? DIN 6340 denotes standardised washer geometry; compliance ensures consistent dimensions and predictable behaviour under clamping loads for the AMF washer. How do the dimensions affect joint stability? The combination of 35 mm outer diameter and 5 mm thickness increases contact area and stiffness, which helps maintain clamp force and reduce material indentation. Can the washer be used in structural assemblies with dynamic loads? Yes. The defined thickness and diameter provide improved resistance to deformation under cyclic loading compared with thinner, smaller washers. Manufacturer: AMF / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
14.2mm Countersink DIN 6319G 120° Cone Angle For M12 Screws, D4 36 H3 6 - AMF
Benefit from precise joint alignment, conformity to DIN 6319G and a defined 120° cone angle for consistent seating; order the AMF conical seat directly via Metav Werkzeuge or consult our specialists for application advice. Conical seat DIN 6319G (AMF) — Cone washer for M12, 14.2 mm bore, 120° Conical seat DIN 6319G — a seating washer designed to provide accurate axial alignment and uniform load transfer for M12 bolted connections in industrial and workshop assemblies Conforms to DIN 6319G standard Fits M12 screws with 14.2 mm bore 120° cone angle for precise seating Ensured alignment and reduced joint stress A conical seating washer manufactured to the DIN 6319G specification provides a controlled contact geometry that reduces eccentric loading and improves clamp distribution. The defined 120° cone angle generates a repeatable seating surface that minimises wobble and localised stress concentrations. In practice, the standardised geometry supports consistent torque-to-preload behaviour and contributes to longer joint lifetime, making the component suitable where reliable clamping and repeatability are required. Straightforward compatibility with common fasteners Designed for use with M12 fasteners, the item features a 14.2 mm bore and defined assembly dimensions (D4: 36 mm; H3: 6 mm) that allow immediate integration without additional machining. The larger outside diameter ensures an adequate bearing surface while the bore clearance accommodates standard M12 bolt shanks. These measurable values permit quick verification during inventory or assembly planning and simplify part selection for routine maintenance or series production. Workshop-ready standard component for industrial use Produced under the AMF designation, this cone washer serves as a compact, standardised solution for a wide range of bolted connections in mechanical engineering and maintenance operations. Its adherence to an established norm supports quality control processes and eases procurement decisions. Supplied in single units, the part is suitable for spare-part provisioning or targeted replacements in maintenance kits and assembly lines. Contact Metav Werkzeuge for rapid supply and specification advice on AMF conical seats; email info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: 4000833448NW Standard: DIN 6319G Brand: AMF Type: Conical seat (cone washer) Dimensions & core data Bore / D2: 14.2 mm Outside diameter / D4: 36 mm Height / H3: 6 mm Cone angle: 120° Suitable for: M12 Design & special features Conical seating washer Pack unit: 1 Label: Kegelpfanne DIN 6319G for screws M12, bore dia. 14.2 mm, cone angle 120° FAQ Is the component suitable for standard M12 bolts? Yes. The AMF conical seat is designed for M12 fasteners and features a 14.2 mm bore to provide appropriate clearance for M12 bolt shanks. What standard does this seating washer comply with? The part conforms to DIN 6319G, ensuring standardised geometry and reproducible seating performance for bolted joints. Which dimensions are relevant when checking fit? Key dimensions are the bore (14.2 mm), outside diameter (36 mm) and height (6 mm); these determine compatibility and bearing surface in assemblies. How does the 120° cone angle affect joint behaviour? A 120° cone angle provides a defined seating interface that promotes uniform load distribution and reduces eccentric forces, improving joint stability. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com