21mm Washer DIN 6340 For M20 Bolts 50mm Outer Diameter 6mm Thick - AMF
Benefit from DIN 6340 conformity, a 21 mm bore tailored for M20 fastenings and a robust 6 mm thickness that delivers reliable load distribution; order directly via Metav Werkzeuge or consult our technical advisers for specification support. U-washer (DIN 6340) for M20 screws, bore Ø21 mm – AMF A U-washer (DIN 6340) engineered to ensure secure M20 screw connections in industrial assemblies and standard workshop applications. DIN 6340 compliant 21 mm bore for M20 bolts 6 mm robust thickness 50 mm outer diameter Consistent standard compliance for predictable assemblies Conformity with DIN 6340 guarantees dimensional accuracy and repeatable fit, which reduces variations in production and maintenance. For procurement and inventory planning this standardisation means fast replacement and assured interchangeability. The compliance also simplifies quality control procedures: inspection protocols can reference the recognised DIN tolerances rather than bespoke measurements, saving time in acceptance testing and enabling predictable joint behaviour in series assemblies. Optimised geometry for M20 bolting and pressure distribution The combination of a 21 mm bore, a 50 mm outer diameter and 6 mm thickness provides effective surface contact and even stress distribution beneath the bolt head or nut. The slightly oversized outside diameter lowers the unit pressure on softer substrates, limiting embedment and preserving component surfaces. Where a reliable clamp force is required, this form factor improves joint stiffness and reduces the risk of localised deformation, making the AMF washer a practical choice for heavy-duty threaded connections. Practical benefits in workshop and industrial use With its standardised design, the washer supports streamlined assembly workflows and reduces rework. The U-washer is suitable for repeat installations and maintenance cycles where consistent joint behaviour is critical. Because the component is manufactured to a recognised standard, documentation and parts lists remain concise and unambiguous, which helps logistics and service teams speed up repairs and lowers the risk of incorrect part selection. How the washer improves bolted-joint performance Beyond basic spacing, the primary function is load distribution and protection of the clamped surfaces. By increasing contact area, the washer reduces localised stress peaks and helps maintain clamp preload under dynamic loads. In applications combining metric M20 bolts with standard nuts or heads, this washer complements torque settings by offering a predictable interface that supports reliable clamp force transmission and longer joint life. For specification advice or to secure standard-compliant AMF washers for M20 applications, contact Metav Werkzeuge in Emmerich for tailored recommendations and prompt supply: info@metav-werkzeuge.com | +49 2822 7131930 Technical data Article number: 4000833442NW SKU/UID: 4000833442NW Manufacturer: AMF Product type: Washer Standard: DIN 6340 Dimensions / Core data Bore diameter (D1): 21 mm Outer diameter (D2): 50 mm Thickness (S): 6 mm Suitable for: M20 Packaging unit: 1 Features / Applications For use with M20 bolts and standard nuts Standardised geometry for interchangeability Designed for industrial and workshop assemblies Label: U-Scheibe DIN 6340 f.Schrauben M20 Bohrungs-D.21mm AMF FAQ What standard does this washer comply with? The washer complies with DIN 6340, ensuring standardised dimensions and tolerances for reliable replacements. Is the bore size suitable for M20 bolts? Yes, the 21 mm bore is specified for M20 threaded connections and pairs correctly with standard M20 bolts and nuts. What are the key dimensions to check for compatibility? Check the 21 mm bore, 50 mm outer diameter and 6 mm thickness to ensure compatibility with mating components and surface load requirements. Can this washer be used in heavy-duty clamping applications? The washer’s 6 mm thickness and wide outer diameter provide improved load distribution, making it suitable for many heavy-duty bolted joints. Which SKU identifies this AMF washer? The product is listed under SKU/UID 4000833442NW, labelled as a DIN 6340 washer for M20 screws. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
22mm Clamp Bar Nr. 6314V Height 19-105mm M20 Thread With M20x22x200 Clamping Screw - AMF
Take advantage of a compact, adaptable clamping solution with a 22 mm T‑slot interface, an adjustable clamping height of 19–105 mm and a robust M20 thread for standard clamping screws; order directly via Metav Werkzeuge or consult our specialists for integration advice. Spanneisen Nr. 6314V – Clamping arm for 22 mm T‑slot, H 19–105 mm (AMF) A Spanneisen Nr. 6314V provides versatile clamping for workshop and production fixturing, designed to engage 22 mm T‑slots and accept standard M20 clamping screws. For 22 mm T‑slot tables Adjustable clamping height 19–105 mm Thread M20 for standard clamping screws Compact 160 mm overall length Secure, adaptable clamping that speeds up setup times The clamping arm is configured for direct integration with machines and fixtures that use a 22 mm T‑slot, allowing quick attachment and repeatable positioning. The broad clamping height 19–105 mm range enables handling of varied workpiece sizes without multiple intermediate components, which reduces setup changes and minimises downtime. This adaptability supports lean workflows and helps maintain consistent clamping pressure across production runs. Standardised thread for reliable force transmission Equipped to accept an M20 thread, the component pairs with common clamping screws such as M20 x 22 x 200, delivering secure and predictable holding force for machining and assembly operations. Using established thread standards simplifies maintenance and replacement, so clamp assemblies remain serviceable with off‑the‑shelf fasteners. The standardised interface therefore contributes directly to operational reliability and easier spare‑part management. Compact footprint and clear dimensional data for easy planning With a 160 mm overall length and 22 mm width, the clamping arm fits into tight fixture layouts while providing a stable lever for clamping actions. The concise dimensional profile supports efficient nesting on modular fixturing plate systems and helps planners calculate clearances quickly. Clear numeric specifications make the component straightforward to include in CAD layouts or BOMs, reducing ambiguity during procurement and installation. For dependable clamping in standard T‑slot setups, request the AMF clamping arm Nr. 6314V via Metav Werkzeuge — our consultants at Metav Werkzeuge will advise on compatibility and order fulfilment to ensure rapid integration into existing jig and fixture systems Technical data Article number: 4000603038NW Type: Nr. 6314V Product type: Clamping arm Manufacturer: AMF Packing unit: 1 Key measurements Clamping height: 19–105 mm T‑slot: 22 mm Width: 22 mm Overall length: 160 mm Thread: M20 Special features Compatible clamping screw: M20 x 22 x 200 Additional dimensions: A: 30; B2: 60; E1: 30; E2: 60; LS: 109 FAQ What T‑slot size is this clamping arm designed for? This clamping arm is designed for a 22 mm T‑slot and is supplied as the Spanneisen Nr. 6314V (AMF, SKU 4000603038NW) for direct mounting in standard 22 mm table slots. What is the clamping height range and why does it matter? The clamping height range is 19–105 mm; this range allows the Spanneisen Nr. 6314V to secure a wide variety of workpiece heights without additional spacers, improving fixture flexibility. Which clamping screw fits the assembly? The assembly is compatible with an M20 x 22 x 200 clamping screw as indicated in the component data; using this standard fastener ensures correct engagement with the M20 thread. Can this clamping arm be used in modular jig systems and CNC fixtures? Yes, the compact design and standard interfaces make the Spanneisen Nr. 6314V suitable for modular jig systems and CNC fixtures where a 22 mm T‑slot and M20 clamping are employed. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
22mm Nutenstein No. 6322B 18mm Slot Width For M6 x 16 Fastening - AMF
Robust fixing for 18 mm T-slots and compatibility with M6 x 16 fasteners deliver secure clamping with minimal profile height; the compact 10 mm section reduces interference in confined assemblies. Order the AMF Nr. 6322B directly via Metav Werkzeuge or consult our specialists for application advice. Nr. 6322B T-slot nut — 18 mm nominal slot, for M6 x 16 fasteners (AMF) The Nr. 6322B T-slot nut is a compact fastening element intended for machines, fixtures and worktables with an 18 mm T-slot, optimised for fixed mounting and standard metric fasteners. Fits 18 mm T-slots Compatible with M6 x 16 fasteners Compact 10 mm profile height Designed for fixed mounting Secure clamping for standard 18 mm tables The component provides a dependable clamping point in 18 mm T-slots, ensuring repeatable positioning of fixtures and workpieces. Its compatibility with M6 x 16 fasteners allows the use of common metric screws for straightforward assembly. As a result, the element reduces lateral play and secures loads without the need for bespoke fasteners, enabling consistent machine set-ups and predictable clamping performance. Low profile that minimises interference With a 10 mm profile height and a total length of 22 mm, the fastening element keeps the clamped area compact and unobtrusive. The reduced height is beneficial where tool paths or adjacent components require clearance, and the compact length aids in installations where space along the slot is limited. These dimensional characteristics help maintain accessibility while providing the required clamping force. Simple integration into fixed mounting assemblies Designed for fixed mounting, the unit suits permanent or semi-permanent fixture arrangements on production jigs and tooling plates. Its standardised geometry for an 18 mm nominal slot simplifies inventory and replacement planning across multiple workstations. The compatibility with standard metric screws shortens assembly time and supports consistent torque settings during installation, which in turn contributes to repeatable clamping quality. Suitable choice for workshop and industrial applications Manufactured by AMF, this T-slot nut is a practical option for workshops and production environments seeking a reliable, compact fastening solution. Supplied as a single unit per packaging, the component supports targeted replacements and small-batch fitting tasks. The straightforward design focuses on function and compatibility, making it a pragmatic choice where proven standard parts are preferred over customised solutions. For secure, standardised T-slot fixation with an 18 mm nominal slot, request the AMF Nr. 6322B via Metav Werkzeuge in Emmerich for specification checks and supply at info@metav-werkzeuge.com or +49 2822 7131930 Technical data SKU: 4000833229NW Type: Nr. 6322B Manufacturer: AMF Product type: T-slot nut UID: 4000833229NW Dimensions Height: 10 mm Total length: 22 mm Nominal slot width: 18 mm Compatible fastener: M6 x 16 Special features Packaging unit: 1 Fixed mounting variant Label: T-slot nut Nr. 6322B — nominal slot 18 mm — fixed mounting — AMF FAQ What slot size is this T-slot nut designed for? The T-slot nut is sized for an 18 mm nominal slot width, providing a standard fit for 18 mm T-slots. Which screw size fits this nut? The component accepts M6 x 16 fasteners, allowing the use of standard M6 screws with a 16 mm length. What are the key dimensions of the fastening element? Key measurements are a 10 mm profile height and a total length of 22 mm, offering a compact footprint. Is this item suitable for permanent fixture mounting? Yes; the design is for fixed mounting, intended where a secure, lasting clamping point is required. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
22mm Slot Nut Nr. 6322A For Fixed Mounting, Fits M6 x 16 - AMF
Take advantage of a precise fit for mixed machine and fixture T-slots combined with a fixed‑mount design and compatibility with standard M6 x 16 fastenings for reliable clamping performance; order directly via Metav Werkzeuge or consult our technical team for application advice. Nr. 6322A T-slot nut (nominal slot 22/20 mm) by AMF The Nr. 6322A T-slot nut is a fixed‑mount fastening component for 22 mm machine and 20 mm fixture T‑slots, designed to accept M6 x 16 screw connections for secure clamping in workshop and production environments Precision fit for 22/20 mm T-slots Designed for fixed mounting Suitable for M6 x 16 fastening Robust AMF component quality Precise compatibility that shortens set‑up time The combination of nominal slot dimensions 22/20 mm and a finish intended for fixed mounting ensures a repeatable seating position in machine tables and dedicated fixtures, which reduces alignment effort during assembly and tool changes. A defined interface for M6 x 16 fastenings simplifies parts selection and inventory management, meaning less time is spent checking screw dimensions and more on productive machining. In practice, the precise fit results in improved clamping consistency and reduced rework. Secure fixed mounting for vibration‑resistant clamping The fixed‑mount configuration delivers a stable connection between workholding elements and the machine or jig, lowering the risk of micro‑movement under cutting loads. This stability supports process reliability and helps preserve dimensional tolerances across production batches. With a component designed specifically for fixed installation, maintenance cycles are more predictable and fixture life is extended through reliable force distribution during clamping operations. Clear integration into existing workshop systems Specified for standard T‑slot sizes and M6 screw engagement, the component integrates easily into conventional machine tables and tooling plates, allowing rapid retrofitting or new fixture design without specialist adapters. Technical teams benefit from the straightforward specification: nominal slot widths and screw compatibility are defined, simplifying drawings and procurement lists. For workshops seeking reproducible clamping results, this T‑slot nut supports consistent setup procedures and reduces assembly complexity. For tailored technical advice or to procure AMF fastening components, contact Metav Werkzeuge in Emmerich by email at info@metav-werkzeuge.com or by phone on +49 2822 7131930 — Metav’s consultants will advise on compatibility and availability Technical data Article number: 4000833238NW Type: Nr. 6322A Product type: T-slot nut Manufacturer: AMF Packaging unit: 1 Facts Nominal slot (machine): 22 mm Nominal slot (fixture): 20 mm Suitable for screw: M6 x 16 HL: 2 mm Special features Fixed mounting design Precision fit for 22/20 mm T-slots AMF component label and SKU 4000833238NW FAQ What slot widths does this T‑slot nut fit? The T‑slot nut is specified for a 22 mm nominal machine slot and a 20 mm nominal fixture slot, providing a defined seating for mixed‑use setups. Which screw size is recommended for mounting? The component is designed to accept M6 x 16 screws for secure fixed mounting in compatible T‑slots. Is this item suitable for regular machine table retrofits? Yes, the nut’s specification and fixed‑mount design allow straightforward integration into standard machine tables and workshop fixtures. Does the product offer vibration resistance during heavy cutting? The fixed‑mount configuration and precision fit of the AMF T‑slot nut reduce micro‑movement and contribute to stable clamping under cutting loads. How is the item delivered and what is the packaging unit? The item is supplied with a packaging unit of 1 and is listed under SKU 4000833238NW for order reference. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
22mm Slot Nut Nr.6322B For 20mm Slot, Height 10mm, For M6 x 16 Fastening - AMF
Take advantage of the combination of compact dimensions, secure fastening and straightforward installation to keep assembly processes efficient and reliable; order the item via Metav Werkzeuge or consult Metav's specialists for compatibility advice. AMF T-slot nut Nr. 6322B — for 20 mm slot, compatible with M6 x 16 The AMF T-slot nut Nr. 6322B is a purpose-built T-slot nut for modular fixture systems, intended for fixed mounting in profiles with a nominal 20 mm groove and compatible with standard M6 x 16 fasteners T-slot nut for 20 mm slot Compatible with M6 x 16 fasteners Compact dimensions: 22 mm length, 10 mm height Flat design for fixed mounting Secure, standardised clamping for profile systems The AMF component provides a reliable connection between fixtures and standard aluminium profiles. Designed for a 20 mm slot, this T-slot nut accepts common M6 threads and therefore simplifies part selection across a wide range of modular assemblies. The design translates technical compatibility into practical benefits: reduced downtimes when changing setups, fewer special parts to manage and predictable mechanical behaviour under clamping loads. Where installation speed and repeatability matter, the combination of slot compatibility and standard fastener size supports efficient assembly lines and jigs. Compact shape reduces interference and eases installation With an overall length of 22 mm and a height of 10 mm, the nut occupies minimal profile space while delivering a secure anchoring point. The flat design for fixed mounting prevents rotation during tightening and ensures a stable seating surface, which lowers the risk of misalignment in narrow assemblies. For engineers and workshop planners this means simpler mounting procedures, fewer alignment iterations and cleaner component layouts on workbenches or machine tables. Clear, compact dimensions also assist with CAD planning and automatic parts lists for production runs. Simplified inventory and dependable supply for workshops Standardised parts such as this T-slot nut reduce SKU complexity and support lean stocking strategies. Supplied in single units, the component is easy to sample and integrate into prototypes or small batches before scaling procurement. The SKU 4000833230NW and type Nr. 6322B make traceability straightforward in procurement systems and maintenance lists. Backing from an established distributor ensures continuity of supply and a quality filter at the logistics hub in Emmerich, which supports reliable restocking and consistent part quality for workshops and production facilities. Secure a reliable stock of AMF T-slot nut Nr. 6322B through Metav Werkzeuge for consistent assembly performance; contact Metav Werkzeuge for technical clarifications at info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: 4000833230NW Type: Nr. 6322B Manufacturer: AMF Product type: T-slot nut Label: Nutenstein Nr.6322B Nennmaß der Nut 20mm fl.z.Festmontage AMF Dimensions Overall length: 22 mm Height: 10 mm Suitable for: M6 x 16 Special features Addition: B: 20 Flat design for fixed mounting Packaging unit: 1 FAQ What slot width is this nut intended for? The nut is intended for a nominal 20 mm slot, as indicated by the product label and the Addition B: 20 specification for the AMF T-slot nut Nr. 6322B (SKU 4000833230NW). Which fastener size fits this T-slot nut? This T-slot nut is compatible with M6 x 16 fasteners, providing a standardised connection for common assembly tasks. What are the overall dimensions of the part? The component measures 22 mm in length and 10 mm in height, dimensions that support compact installations and convenient CAD planning. Is the nut suitable for fixed mounting? Yes — the design includes a flat side for fixed mounting, which reduces rotation during tightening and improves seating stability in profile grooves. How is the part supplied for initial testing or small production runs? The nut is supplied per the packaging unit of 1, allowing easy sampling and incremental stocking of the AMF T-slot nut Nr. 6322B. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
22mm T-Slot Bolt M20 L125mm Grade 8.8 With Nut And Washer, DIN 787 - AMF
Take advantage of a DIN 787‑compliant design combined with an M20 thread and 125 mm overall length for robust, repeatable clamping in T‑slot applications; the fastener’s strength class 8.8 and delivery with nut and washer ensure reliable assembly and reduced procurement steps. Order the AMF T‑slot screw directly via Metav Werkzeuge or consult our specialists for specification support. AMF T‑slot screw DIN 787 – 22 mm T‑slot, M20 x 125 mm, grade 8.8 A T‑slot screw designed for secure fixturing in 22 mm T‑slots, offering standardised dimensions and industrial strength for machine tables and clamping systems. DIN 787 standardised dimensions M20 thread for high clamping force 125 mm overall length for deep fixtures Includes nut and washer for direct use Reliable performance for production clamping The fastener conforms to DIN 787, which defines the geometry and fit for T‑slot bolts used in machine tables and fixtures. The M20 thread combined with a 125 mm overall length provides a high clamping leverage and makes tightening procedures predictable under service conditions. Specified as strength class 8.8, the component offers a balance of tensile strength and toughness suitable for routine industrial use, reducing downtime caused by fastener failure and ensuring consistent part alignment during machining or assembly processes. Compact handling and immediate fitment benefits Supplied complete with nut and washer, the assembly is ready for immediate installation, eliminating the need to source hardware separately and speeding up fixture changes. The 22 mm head profile is matched to standard T‑slot widths for a secure, anti‑rotation fit, which improves repeatability in production set‑ups. Where quick changeovers are required, the standardised form factor simplifies inventory management and reduces time spent on assembly preparation. Robust choice for workshops and production lines Chosen for its standardized geometry and proven strength class, this T‑slot fastener supports reliable clamping across a wide range of applications from toolroom jigs to shop‑floor fixtures. The combination of DIN compliance, thread size and included fastening elements contributes to a predictable service life and lower overall maintenance effort. For buyers seeking an efficient supply route, the item aligns with Metav’s emphasis on accessible precision and dependable delivery. For procurement or technical selection of AMF T‑slot screws, contact Metav Werkzeuge for tailored advice and reliable supply coordination via info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: 4000833352NW SKU / UID: 4000833352NW Standard: DIN 787 Brand: AMF Facts Thread: M20 T‑slot compatibility: 22 mm Overall length: 125 mm Packaging unit: 1 Special features Strength class: 8.8 Delivered with nut and washer Product type: T‑slot screw Axial enrichments: A: 21.7; B: 85; E: 35; K: 14 FAQ What T‑slot width does this fastener fit? This T‑slot screw is designed for a 22 mm T‑slot and matches the standard head geometry specified under DIN 787. Does the delivery include fastening hardware? Yes, the AMF T‑slot screw is supplied with nut and washer, ready for immediate assembly. What do DIN 787 dimensions guarantee? DIN 787 ensures standardised head and shank geometry for T‑slot bolts, so the fastener will fit correctly into machine tables and clamping rails compliant with the same standard. Which thread and length are specified for this fastener? The component uses an M20 thread and an overall length of 125 mm, suitable for deeper fixture requirements. How is the item packaged? The product is supplied in a packaging unit of 1. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
22mm T-Slot Nut M16 DIN 508, Strength Class 10 - AMF
Take advantage of the precise fit and high clamping capacity offered by this component: compatibility with DIN 508, a 22 mm T-slot profile and an M16 threaded core ensure reliable fixture retention; the strength class 10 rating adds durability for demanding clamping operations. Order the component directly via Metav Werkzeuge or contact our consultants for application advice. T-slot nut (DIN 508) — 22 mm, M16 | AMF A T-slot nut (DIN 508) for secure fixture mounting in 22 mm table slots, designed for heavy-duty clamping and standardised machine tool tables DIN 508 standard compliant For 22 mm T-slots M16 threaded fastening Strength class 10 for heavy clamping Accurate seating for standard machine tables The T-slot insert is manufactured to meet DIN 508, guaranteeing a consistent and predictable fit in standard 22 mm T-slots. With an overall height of 28 mm and axial dimensions A 21.7 mm, E 35 mm and K 14 mm, the component provides a defined seating surface that reduces lateral play and improves repeatability when mounting clamps or fixtures. This compatibility with common slot geometries simplifies fixture planning and reduces setup time on the shop floor. Robust fastening for demanding clamping tasks Featuring an M16 internal thread and rated strength class 10, the part is engineered for high clamping loads where secure retention is critical. The tensile performance implied by the strength class supports heavy-duty applications while preserving joint integrity during machining cycles. Specifying a high-strength T-slot fastener like this helps maintain consistent clamping force over repeated use, lowering the risk of slippage and the need for frequent retorquing. Straightforward integration and stock-ready supply Designed as a direct replacement or upgrade for factory-standard T-slot hardware, the item integrates seamlessly into existing workholding systems and modular fixtures. Supplied singly (packing unit: 1) and clearly identified by SKU 4000603169NW, the component from AMF simplifies inventory management for workshops and production lines. The standardised geometry and thread size make procurement and stocking predictable, supporting efficient order cycles and faster assembly on the production bench. Contact Metav Werkzeuge for application guidance or to reserve AMF T-slot nuts (SKU 4000603169NW); email info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: 4000603169NW UID: 4000603169NW Manufacturer: AMF Product type: T-slot nut Standard: DIN 508 Facts Height: 28 mm T-slot width: 22 mm Thread: M16 Axial dimensions: A 21.7 mm, E 35 mm, K 14 mm Strength class: 10 Packing unit: 1 Special features Factory standard: DIN 508 Suitable for securing fixtures and workholding in machine tables Single-piece supply for predictable stocking FAQ What slot width does this T-slot nut fit? The T-slot nut is designed for 22 mm T-slots as specified under DIN 508, ensuring correct seating in standard table profiles. Which thread size is provided? This component is supplied with an M16 internal thread for direct connection to M16 bolts and clamping elements. What are the key axial dimensions to check for compatibility? Check the axial dimensions A 21.7 mm, E 35 mm and K 14 mm to confirm fit and seating on the table slot, as these determine how the nut engages the slot profile. How does the strength class affect application? The strength class 10 rating indicates high mechanical capability suitable for demanding clamping operations, providing robust retention under load. Is the item supplied individually or in sets? The part is supplied as a single unit (packing unit: 1) and is listed under SKU 4000603169NW for straightforward ordering and inventory control. Manufacturer: AMF; Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
22mm T-Slot Nut M20 High Strength Class 10, DIN 508 - AMF
Robust clamping performance and standard compliance make this component a dependable choice for fixture work: 22 mm T-slot compatibility, M20 thread and strength class 10 deliver high clamping forces and long service life. Order the T-nut directly via Metav Werkzeuge or consult the technical team for integration advice. T-Nut DIN 508 T-Nut 22mm M20 AMF — M20 thread for 22 mm T-slots A T-Nut DIN 508 T-Nut 22mm M20 AMF designed for secure clamping in 22 mm T-slots on machine tables, clamping plates and fixturing systems. DIN 508 compliant T-nut M20 metric thread for high clamping force Compatible with 22 mm T-slots Strength class 10 for increased durability High clamping force for demanding fixtures The design offers a compact profile with a M20 internal thread and a strength class 10, enabling reliable torque transmission for heavy clamping tasks. The combination of thread size and hardness class ensures the component withstands repeated tightening cycles without significant deformation, which supports consistent assembly quality in production environments. This makes the element suitable where firm, vibration-resistant fixing is required in milling tables and modular fixture systems. Precise dimensions for predictable assembly Manufactured to DIN 508, the T-nut provides reproducible geometry for automated positioning and manual assembly alike. Key dimensions — 22 mm T-slot compatibility, height 28 mm and sectional measures A 21.7 mm / E 35 mm / K 14 mm — enable planners and machinists to verify fitment quickly and avoid iterative adjustments. Clear dimensional data supports CAD integration and reduces setup time on jigs or machine tables, improving throughput in batch production. Reliable standard conformity and workshop fit Compliance with the recognised standard assures compatibility across suppliers and fixture systems, reducing the risk of mismatched components. The part is suited for industrial clamping applications and retrofit operations where standardised, interchangeable parts are required. Traceable identification via the SKU and documented measurements simplifies procurement and inventory management for maintenance departments and toolrooms. For firm, standard-compliant clamping choose the AMF T-nut: contact Metav Werkzeuge for availability, technical clarification and ordering at info@metav-werkzeuge.com or +49 2822 7131930 Technical Data Article number: 4000833210NW Product type: T-Nut Brand: AMF Standard: DIN 508 Facts T-slot width: 22 mm Height: 28 mm Thread: M20 Dimensions A: 21.7 mm; E: 35 mm; K: 14 mm Strength class: 10 Packaging unit: 1 Special features DIN 508 compliant Metric thread M20 For 22 mm T-slot systems Compact, robust design FAQ What T-slot width does this T-nut fit? The T-nut fits a 22 mm T-slot and is specified for standard 22 mm machine table grooves. Which thread size is provided with the T-nut? The component has an internal M20 metric thread designed for high clamping loads. Is this part compliant with industry standards? Yes, the T-nut is manufactured to DIN 508, ensuring compatibility with standard fixturing systems. What are the key dimensions relevant for installation? Relevant measures include height 28 mm and sectional dimensions A 21.7 mm, E 35 mm, K 14 mm, which facilitate fitting and CAD verification. How does strength class 10 affect usage? Strength class 10 indicates higher tensile and yield properties, supporting repeated tightening and demanding clamping applications with improved resistance to wear and deformation. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
22mm T-Slot Nut M20 Rhombic High Strength Class 10, Height 28mm - AMF
Take advantage of high compatibility and proven strength: the 22 mm T-slot and M20 thread combine with a rhombic profile and strength class 10 to deliver a secure clamping solution that integrates with standard aluminium profiles; order directly via Metav Werkzeuge or request technical advice from the Metav team. T-slot Nut No. 510 — 22 mm T-slot, M20 thread, rhombic profile by AMF T-slot Nut No. 510 is a rhombic-profile T-slot nut engineered for secure fastening in 22 mm T-slots, featuring an M20 metric thread for robust connections. 22 mm T-slot compatibility M20 metric thread for heavy-duty fixings Rhombic profile for positive clamping Strength class 10 rated construction Proven compatibility with standard 22 mm profiles for reliable assembly The design focuses on straightforward integration: the 22 mm T-slot width matches common aluminium profile systems, while the M20 thread provides a widely used metric interface for bolts and studs. The rhombic cross-section converts tightening torque into a positive mechanical grip, reducing the risk of rotation under load. These characteristics make the component suitable for machine frames, workholding systems and modular fixtures where standardised interface dimensions contribute to faster assembly and fewer errors. The result is a repeatable connection that supports efficient production workflows. Clear dimensioning for predictable clamping behaviour With measured additions of A 21.7 mm, E 35 mm and K 14 mm, the part offers defined contact surfaces that simplify layout and ensure predictable clamping geometry. The specification also notes a strength class 10, indicating elevated material performance for demanding applications where higher tensile resistance is required. Such numeric values enable planners to verify fit and safety margins during design reviews and to select suitable mating fasteners with confidence. Where tolerance stacks are critical, these dimensions provide a verifiable basis for CAD modelling and procurement documentation. Operational benefits and supply reliability from a trusted partner Beyond mechanical performance, the component supports lean assembly practices: standardisation on a T-slot width and a metric thread reduces inventory complexity and speeds up maintenance interventions. Sourcing through an established supplier brings additional assurance: Metav Werkzeuge combines a broad portfolio with logistical reliability, backed by a large customer base and central European distribution. That supply chain transparency helps avoid production downtime and keeps workstations supplied with compatible fastening elements for rapid assembly or retrofit tasks. Contact Metav Werkzeuge for tailored advice on the AMF T-slot Nut No. 510 (SKU 4000833222NW) and to arrange immediate supply or technical clarification from Emmerich’s specialist team Technical Data Article number: 4000833222NW Type: No. 510 Label: T-slot nut No. 510 T-slot 22mm M20 rhombic AMF Facts Height: 28 mm T-slot width: 22 mm Thread: M20 Addition: A: 21.7 mm; E: 35 mm; K: 14 mm; Strength class: 10 Packaging unit: 1 Special features Rhombic profile Metric M20 thread Suitable for 22 mm T-slots Manufacturer: AMF FAQ Is this T-slot nut compatible with standard 22 mm aluminium profiles? Yes. The AMF T-slot Nut No. 510 (SKU 4000833222NW) is designed specifically for 22 mm T-slot profiles and mates with standard aluminium framing systems. Which thread size is used for fastening? The part features an M20 metric thread, allowing the use of common M20 bolts or studs for heavy-duty connections. What does the strength class 10 indicate for performance? Strength class 10 denotes elevated tensile and yield properties, so the T-slot nut from AMF delivers improved resistance against shear and pull-out in demanding assemblies. Are the dimensional additions provided for design verification? Yes. The values A 21.7 mm, E 35 mm and K 14 mm describe the critical contact dimensions and support precise CAD integration and tolerance checks. Can this nut be used in load-bearing fixture applications? The combination of a rhombic profile and strength class 10 makes the component suitable for many load-bearing fixtures; assessment of the complete joint and fastener selection should follow standard engineering practice. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
22mm T-Slot Nut Nr. 510 M16 Rhombic, Height 28mm, Strength Class 10 - AMF
Robust rhombic T‑slot nut with an M16 internal thread and 22 mm T‑slot compatibility for reliable, repeatable clamping; strength class 10 and a 28 mm height combine to deliver high load capacity and long service life. Order directly via Metav Werkzeuge or request technical guidance from our consultants to confirm fit and installation. T-slot nut No. 510 — rhombic T‑slot element, 22 mm, M16 (AMF) The T-slot nut No. 510 is a rhombic clamping insert designed for 22 mm T‑slots, offering an M16 thread for secure fixture mounting across machine tables and modular workholding systems. Rhombic profile for positive locking Fits 22 mm T‑slot standard M16 internal thread for strong clamping Strength class 10 for high load capacity Secure, high-strength clamping for demanding fixtures The rhombic geometry delivers positive locking in the slot and, together with the M16 thread, ensures clamping reliability under dynamic loads. With a nominal height of 28 mm and defined add-on dimensions A 21.7 mm, E 35 mm and K 14 mm, the component provides predictable bearing surfaces and repeatable positioning. These measurable values translate into reduced setup variation and consistent force transmission, which helps to lower fixture rework rates and improve process stability in production environments. Fast integration with standard machine tables and tooling Compatibility with the 22 mm T‑slot standard simplifies retrofits and new builds: the element slots into common machine and fixture rails without the need for adapters. The compact form factor and internal thread arrangement enable straightforward installation using standard fastening hardware, shortening downtime during changeovers. Clear, numeric data for slot width, thread size and additional dimensions allow planning departments to verify fit in CAD models and BOMs quickly, supporting efficient procurement and reduced assembly times. Industrial-grade performance backed by reliable supply Rated strength class 10, this clamping component is specified for applications where high clamping force and fatigue resistance are required. The rhombic profile and precise manufacturing tolerances contribute to long service intervals and predictable maintenance cycles. As part of Metav’s offering, sourcing from a central European distribution point means steady availability and a quality filter that supports production continuity. Technical documentation and measured values accompany deliveries to support quality assurance and traceability. Contact Metav Werkzeuge for specification checks or to confirm compatibility with existing fixtures — email info@metav-werkzeuge.com or call +49 2822 7131930 to arrange supply and technical consultation on the T‑slot nut No. 510. Technical data Article number: 4000603185NW Type: Nr. 510 UID: 4000603185NW Manufacturer: AMF Product type: T‑slot nut Label: T‑Nutenstein Nr.510 T‑Nut 22mm M16 rhombisch AMF Dimensions & core data Height: 28 mm T‑slot width: 22 mm Thread: M16 A: 21.7 mm E: 35 mm K: 14 mm Strength class: 10 Special features Rhombic profile Designed for 22 mm T‑slots Internal M16 thread High strength class 10 Packaged per 1 unit FAQ What slot size does this nut fit? The element is specified for a 22 mm T‑slot, matching common machine table standards for modular clamping. What thread is provided in the component? An M16 internal thread is integrated to accept standard M16 bolts for strong, repeatable clamping. What does strength class 10 indicate for load capability? Strength class 10 designates the high tensile capability of the part; the T‑slot nut No. 510 is therefore suitable where elevated clamping forces and durability are required. Are additional dimensions available for installation planning? Yes — the supplementary dimensions are A 21.7 mm, E 35 mm and K 14 mm, which support precise integration and CAD verification. Can the component be supplied in larger quantities or special packs? Standard supply is per single unit; consult Metav Werkzeuge for volume orders and packaging options referencing SKU 4000603185NW. Hersteller: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
23.2mm Countersink DIN 6319G 120° Cone Angle for M20 Screws, Bore Ø23.2mm - AMF
The combination of DIN 6319G conformity, a precise Ø23.2 mm bore and a 120° cone angle ensures consistent, flush seating for M20 fastenings; benefit from reliable assembly performance and straightforward specification handling. Order the AMF conical washer directly via Metav Werkzeuge or consult our specialists if application advice is required. AMF Conical Washer DIN 6319G – for M20 Screws, Ø23.2 mm Bore, 120° Cone Angle AMF Conical Washer DIN 6319G provides a standardised seating solution for countersunk fasteners, designed for secure and repeatable mounting in industrial assemblies. DIN 6319G conformity Precision bore Ø23.2 mm 120° cone angle for flush seating For M20 screw assemblies Secure seating for flush countersunk connections A conical washer manufactured to DIN 6319G gives a defined bearing surface for countersunk screw heads. The standardised geometry reduces variability in joint behaviour and helps prevent eccentric loading of the fastener. Specifying a standardised seating element like this AMF component improves process reliability on assembly lines and in maintenance tasks, as the conical profile guides the screw head into a stable, repeatable position for predictable clamping results. Precision dimensions that reduce assembly variance The washer’s measured bore (Ø23.2 mm) and overall geometry, including an outer seating diameter of 50 mm and a height of 8 mm, ensure components align consistently during installation. These precise dimensions lower the need for post-assembly correction and cut down on rework time. When tolerance stacks are critical, using a standardised seating washer limits the number of variables affecting joint integrity and helps maintain torque and preload consistency across multiple fastenings. Integration into workshop and production workflows Designed for use with M20 fastenings and featuring a 120° cone angle, this seating washer fits seamlessly into common bolted-joint designs where flush appearance and load distribution are required. Its conformity to a recognised DIN standard simplifies parts lists and procurement, and it is suited to both one-off repairs and serial production. Specifiers and workshop planners benefit from predictable behaviour in load transfer and can include the component directly in assembly drawings and bills of materials. Contact Metav Werkzeuge for tailored advice and fast supply of the AMF conical washer — call +49 2822 7131930 or email info@metav-werkzeuge.com to discuss application requirements and place an order Technical data Article number: 4000833451NW Manufacturer: AMF Product type: Conical washer Standard: DIN 6319G Packaging unit: 1 Dimensions / Core data Bore diameter D2: 23.2 mm Outer diameter D4: 50 mm Height H3: 8 mm Cone angle: 120° Suitable for screw size: M20 Features / Applications Countersunk seating for flush installation Conforms to DIN 6319G For use with M20 screws Designed for consistent load distribution FAQ What screw size is this seating washer intended for? This AMF conical washer is specified for use with M20 screws and is listed under article number 4000833451NW. What are the key dimensions of the washer? The washer has a bore diameter of 23.2 mm (D2), an outer seating diameter of 50 mm (D4) and a height of 8 mm (H3). Which standard does the washer comply with? The component is manufactured to DIN 6319G, ensuring standardised geometry for countersunk seating. What is the cone angle and why does it matter? The 120° cone angle provides a reliable seating profile that promotes flush installation of countersunk heads and helps distribute load evenly across the bearing surface. Is this suitable for serial production use? Yes — the standardised geometry and precise dimensions of the AMF conical washer support repeatable assembly processes and are appropriate for both serial production and maintenance operations. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
23.2mm Countersink Seat DIN 6319D 120° Cone Angle, For M20 Screws - AMF
Take advantage of the DIN 6319D conformity and the precise 23.2 mm bore to ensure a reliable seat for M20 countersunk screws, improving load distribution and alignment in assemblies; order via Metav Werkzeuge or consult their experts for supply and compatibility. AMF Countersunk Washer DIN 6319D (M20, 23.2 mm, 120°) The AMF Countersunk Washer DIN 6319D provides a defined countersink seat for fastening applications, designed to accommodate M20 countersunk screw heads and to ensure uniform contact in mechanical and structural assemblies. Designed to DIN 6319D standard Suitable for M20 countersunk screws Bore diameter 23.2 mm for accurate seating Countersink angle 120° for matching screw heads Precision seating reduces local stress and improves joint reliability Adherence to DIN 6319D guarantees a standardised geometry that helps distribute clamping forces evenly beneath countersunk screw heads. The defined 120° countersink angle and the 23.2 mm bore ensure that the screw head sits concentrically, which reduces localised material stress and the risk of deformation in thin plates or soft substrates. This measurable conformity simplifies quality checks and supports repeatable assembly processes in production environments. Consistent compatibility and easier assembly for faster production The washer is specified for M20 countersunk screws, enabling straightforward component matching and reducing assembly errors. By providing a precise bearing surface, the seat minimises the need for rework and improves torque transmission from the screw head to the joint. For procurement and inventory planning, the standardised geometry enables interchangeability between batches, supporting predictable lead times and smoother production scheduling. Robust sourcing and technical clarity for professional users Supplied under SKU 4000833471NW, the component is a pragmatic choice for engineers and buyers seeking standard-compliant parts that integrate into existing designs without modification. Clear technical dimensions such as D2 = 23.2 mm, D4 = 36 mm and H3 = 7.5 mm (see technical data) mean the seat can be verified quickly during incoming inspections. The documented specification supports traceability and simplifies supplier audits, reinforcing responsible procurement practices in workshops and industrial operations. For procurement advice, availability checks or compatibility queries regarding the AMF Countersunk Washer DIN 6319D, contact Metav Werkzeuge in Emmerich by phone +49 2822 7131930 or email info@metav-werkzeuge.com to secure supply and technical guidance. Technical data Article number: 4000833471NW Standard: DIN 6319D Product type: Countersunk washer Brand: AMF Suitable for: M20 Facts Bore diameter (D2): 23.2 mm Outer diameter (D4): 36 mm Height (H3): 7.5 mm Countersink angle: 120° Special features Conforms to standardised geometry for repeatability Designed for countersunk screw heads to improve seating Packaged unit: 1 Label reference: Kegelpfanne DIN 6319D f. Schrauben M20 FAQ What screws is this seat designed for? The AMF Countersunk Washer DIN 6319D is designed for use with M20 countersunk screws, providing a matched bearing surface for proper head seating. Why is compliance with DIN 6319D important? Compliance with DIN 6319D ensures standardised dimensions and angles so assemblies behave predictably; this simplifies inspection, replacement and compatibility across suppliers. How does a 120° countersink improve joint performance? A 120° countersink matches the geometry of corresponding screw heads, increasing contact area and reducing point loads, which enhances joint longevity and reduces the risk of material damage. Can this washer be used in structural or mechanical assemblies? Yes, the defined seating and load distribution characteristics make the component suitable for both structural and mechanical fastening tasks where standardised countersunk connections are required. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
23–51mm Clamping Support Pad Set Universal, Size 1 - AMF
Take advantage of the combination of adjustable height range (23–51 mm) and compact Gr.1 sizing to achieve consistent, repeatable clamping without lengthy setup. Order the set directly via Metav Werkzeuge or request technical guidance for integration into existing clamping systems. Clamping shim set No. 6500E – Gr.1, adjustable 23–51 mm (AMF) The Clamping shim set No. 6500E Gr.1 from AMF provides a compact, universally applicable solution for fine height adjustment in clamping setups. Variable height range 23–51 mm Universal application for clamping tasks Compact Gr.1 for confined workspaces Repeatable positioning and quick stacking Reliable height compensation that reduces setup time A clamping shim set such as the No. 6500E Gr.1 is designed to provide precise height compensation between clamping elements and workpieces. With a height range of 23–51 mm, the set removes the need for improvised shimming and repeated adjustments, enabling faster fixture set-up and shorter machine idle time. The numerical values H min: 23 mm and H max: 51 mm indicate the minimum and maximum achievable stack height; the clear range supports predictable results in jigs and vice fixtures. For production environments, this translates into measurable time savings and fewer reworks caused by misalignment. Defined contact dimensions for stable clamping and predictable force distribution The shim geometry is specified by A: 19 mm, B: 30 mm and C: 33 mm, which describe the relevant contact widths and effective seating dimensions. These nominal measures ensure a consistent interface with commonly used clamping components and enable correct load distribution across the contact surfaces. Using defined contact dimensions improves clamping stability and reduces the risk of localised deformation under clamping loads. In practical terms, such predictability supports repeatable precision and simplifies quality assurance procedures. Universality and workflow benefits for workshops and production lines Thanks to its universal application, this shim set suits a wide variety of clamping scenarios in both maintenance and production. The compact Gr.1 format is especially useful where space is restricted or when fine stacking is required to reach exact heights. By adopting standardised shims, procurement and stockkeeping become simpler, and changeovers are quicker because the same set can address multiple fixturing tasks. The result is a pragmatic combination of efficiency and adaptability that aligns with modern lean workflows. For reliable integration into existing jigs and fixtures, contact Metav Werkzeuge for availability and technical assistance at info@metav-werkzeuge.com or call +49 2822 7131930 — Metav’s specialists will advise on matching the No. 6500E Gr.1 to specific clamping systems. Technical Data Article number: 4000833090NW Typ: Nr. 6500E - 1 Label: Spannunterlage Nr.6500E Gr.1 universell einsetzbar AMF Dimensions / Core Data H min: 23 mm H max: 51 mm A: 19 mm B: 30 mm C: 33 mm Special features / Versions Product type: Clamping shim set Brand: AMF Universal application: yes Packaging unit: 1 FAQ What height range does the shim set cover? The set covers a height range from 23 mm to 51 mm, enabling precise height compensation for a variety of clamping setups. Which contact dimensions define the shim geometry? The key contact dimensions are A: 19 mm, B: 30 mm and C: 33 mm, which determine seating and load distribution characteristics. Is this set suitable for tight or restricted workspaces? Yes. The Gr.1 format is compact and intended for use where space is limited or when fine stacking is required to reach exact clamping heights. Can the No. 6500E be used across different clamping systems? The No. 6500E Gr.1 is described as universally applicable and is compatible with a range of standard clamping arrangements; verification against specific fixture interfaces is recommended. Manufacturer: AMF; Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
24mm Hex Nut M16 Pressed And Face-Machined Strength Class 10, DIN 6331 - AMF
Reliable, standard-compliant fastening that combines DIN 6331 conformity with strength class 10 and precision-milled contact faces for dependable clamping. Take advantage of consistent torque transfer and compact dimensions for robust assemblies; order the M16 hexagon nut directly via Metav Werkzeuge or consult our specialists for application advice. Hexagon Nut DIN 6331 M16 (SW 24, Strength 10) – AMF The Hexagon Nut DIN 6331 M16 is a precision-machined fastening element designed for high-load industrial assemblies and maintenance tasks, offering standard compatibility and reliable clamping performance. DIN 6331 standardised geometry Strength class 10 for high loads 24 mm spanner width (SW 24) Precision milled faces, total height 24 mm Reliable clamping for demanding assemblies Manufactured to the DIN 6331 specification, this fastening element provides a predictable interface with standard bolts and threaded components. The M16 designation denotes the nominal thread size, ensuring compatibility with existing metric hardware. With strength class 10, the part is engineered for high clamping forces, which translates into fewer loose connections and reduced downtime in production and maintenance environments. The clear technical standard reduces sourcing uncertainty and supports process planning. Precision machining that improves assembly efficiency Pressed and precision-milled faces deliver consistent contact surfaces and accurate seating under tool engagement. The combination of milled flats and a defined 26.8 mm corner measure produces uniform torque transfer to the clamped joint, helping to avoid uneven preload and repeated retorquing. The compact 24 mm spanner width and a total height of 24 mm make the component easy to handle during automated or manual assembly, shortening cycle times without compromising reliability. Versatile industrial use and installation benefits Suitable wherever elevated load capacity and standard compliance are required, this hexagon nut supports machine building, fixture assembly and general workshop repairs. Its standard geometry simplifies inventory management by matching common metric bolt dimensions, while the robust design aids long-term operational safety. For procurement and fitment questions, internal specialists can advise on torque settings and matching fasteners to achieve optimal clamping results. For procurement or technical advice on the AMF Hexagon Nut DIN 6331 M16, contact Metav Werkzeuge in Emmerich by phone or email for prompt, expert support. Technical Data Article number: 4000833413NW SKU: 4000833413NW Type designation: M16 Product type: Hexagon nut Manufacturer: AMF Core data Thread size: M16 Standard: DIN 6331 Total height: 24 mm Spanner width: 24 mm Corner measure: 26.8 mm Package unit: 1 Special features Strength class 10 Pressed and milled faces Standardised geometry for compatibility Precision component for industrial assemblies FAQ What standard does this nut comply with? The component conforms to DIN 6331, ensuring standardised dimensions and interchangeability with metric bolt systems. What load capability does the nut offer? The nut is specified as strength class 10, which indicates suitability for high-clamping-force applications and demanding assemblies. Which spanner size fits this nut? A 24 mm spanner (SW 24) is required to install and remove the nut, matching the stated spanner width. Is this nut suitable for machine building and fixtures? Yes, the Hexagon Nut DIN 6331 M16 from AMF is designed for machinery, fixtures and maintenance where standard compatibility and robust clamping are required. How is the contact surface prepared on this nut? The nut features pressed and precision-milled faces, providing consistent seating and reliable torque transfer. Manufacturer: AMF; Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
24mm M16 Hexagon Nut DIN 6330B Strength Class 10, Overall Height 24mm - AMF
Robust fastening with strength class 10 and a standard M16 thread ensures secure joints; the SW 24 mm across‑flats allows use with common spanners. Order the AMF hexagon nut directly via Metav Werkzeuge or ask our consultants if needed. AMF Hexagon Nut M16 (DIN 6330B) – Strength Class 10, SW 24 mm The AMF Hexagon Nut M16 (DIN 6330B) is a standard fastening component designed for industrial assemblies where secure, repeatable clamping is required. Strength class 10 for high clamping force Across‑flats 24 mm for standard spanners Complies with DIN 6330B for interchangeability Reliable performance for heavy‑duty assemblies The component delivers predictable mechanical performance thanks to its strength class 10 rating, which indicates a high tensile and yield capability suitable for demanding joints. Specified as an M16 hexagon nut under DIN 6330B, this fastening element provides a standardised geometry that supports consistent torque application and repeatable preload. For production environments, this reduces rework and minimises variations in clamping force, translating into fewer unscheduled stops and a steadier assembly quality. Seamless compatibility with common tools and standards Designed with an SW 24 mm across‑flats dimension, the nut fits standard spanners and sockets used in maintenance and assembly shops. Conformity to DIN 6330B ensures interchangeability with equivalent standard parts, simplifying stocking and replacement processes. The established standard means less time spent verifying part fitment and more time on productive work, so tool inventories are leaner and procurement decisions become easier to standardise across sites. Predictable maintenance and reduced downtime Using a standardised hexagon nut from a recognised supplier reduces uncertainty in maintenance cycles. The defined overall height and corner measurements promote consistent thread engagement and predictable torque‑to‑tightness relationships. As a result, bolted joints maintain clamping integrity over repeated service intervals, lowering the risk of loosening under vibration and thermal cycling. This reliability supports a more economical lifecycle by reducing unscheduled inspections and part replacements. Procurement clarity and expert backing from Metav Sourcing from a trusted partner streamlines supply and documentation. Metav combines extensive distribution capacity with sector expertise, offering centralised access to precision components and clear product data for planning and compliance. For purchasers aiming to rationalise suppliers and ensure stable delivery, Metav’s proximity and stock management act as a practical quality filter for the European workshop environment. Contact Metav Werkzeuge today to secure AMF hexagon nuts in strength class 10 for your next production batch and benefit from tailored procurement advice and reliable supply from Emmerich. Technical Data Article number: 4000833398NW SKU: 4000833398NW Type: M16 Standard: DIN 6330B Facts Thread size: M16 Across‑flats (SW): 24 mm Overall height: 24 mm Strength class: 10 Corner measure: 26.8 mm Special features Product type: Hexagon nut Manufacturer: AMF Packaging unit: 1 UID: 4000833398NW Addition: Eckenmaß: 26,8; Festigkeitsklasse: 10 FAQ What thread size does this hexagon nut have? The AMF hexagon nut is specified as M16, corresponding to a standard M16 metric thread. Which standard governs the nut’s dimensions and interchangeability? Dimensions and interchangeability follow DIN 6330B, ensuring the AMF hexagon nut matches equivalent standard parts. What spanner size is required for tightening? The nut uses an SW 24 mm across‑flats dimension, compatible with standard 24 mm spanners and sockets. What strength class is this nut rated to? This AMF hexagon nut is rated strength class 10, intended for applications requiring higher clamping forces. How is the product supplied for ordering and stocking? The item is supplied in a packaging unit of 1; refer to SKU 4000833398NW when ordering. Manufacturer: AMF / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
24mm T-Slot Nut M20 DIN 508 High Strength Class 10, Height 32mm - AMF
Take advantage of standardised compatibility and high tensile performance for dependable clamping in machine tables and fixtures; order supply through Metav Werkzeuge or request technical guidance from our consultants. T-Nutenstein (DIN 508) T-nut 24 mm, M20 — AMF T-Nutenstein (DIN 508) Werksnorm T-Nut 24mm M20 AMF is a precision T-slot clamping element designed for secure fixing in 24 mm T-slots on machine tables, fixtures and modular workholding systems. Standardised DIN 508 compatibility M20 thread for high clamping force Fits 24 mm T-slots precisely Strength class 10 for robust fixation Consistent standard compliance for reliable interchangeability Conformity to DIN 508 ensures predictable fit and function when integrating this component into standard T-slot systems. The design aligns with established machine-table profiles so that replacement or expansion work proceeds without time-consuming adaptations. By using a standardised component, shops and production facilities reduce setup variability and minimise the need for bespoke parts, supporting smoother process planning and faster throughput in repetitive clamping operations. High tensile performance that reduces downtime The nut is specified in strength class 10, which indicates elevated tensile and yield properties compared with lower classes; this reduces the risk of deformation under high preload and contributes to longer service life. Dimensional data supporting precise engagement — including A: 23.7 mm, E: 40, K: 16 — helps ensure secure seating and consistent torque behaviour. For applications that demand repeatable clamp pressure and minimal loosening during cyclical loads, the robust specification offers a clear operational advantage. Practical compatibility and straightforward installation for workshop use Designed for a 24 mm T-slot and with an M20 thread, the component accepts standard M20 bolts or studs for direct connection to clamping elements or workpieces. Installation involves sliding the nut into the slot and orienting it to accept the bolt, enabling quick assembly or reconfiguration of jigs and fixtures. The compact profile and machine-compatible height (32 mm) make it suitable for confined spaces while maintaining the mechanical clearance required for reliable clamping cycles. For supply and professional advice on using AMF T-slot nuts with strength class 10, contact Metav Werkzeuge in Emmerich for tailored assistance and fast delivery: info@metav-werkzeuge.com • +49 2822 7131930 Technical data Article number: 4000833211NW Label: T-Nutenstein (DIN 508) Werksnorm T-Nut 24mm M20 AMF Product type: T-Nutenstein Manufacturer: AMF UID: 4000833211NW Dimensions / Core data T-slot width: 24 mm Thread: M20 Height: 32 mm Packaging unit: 1 Special features Standard: DIN 508 Addition: A: 23.7; E: 40; K: 16 Strength class: 10 FAQ What T-slot width does this nut fit? The T-nut is designed for a 24 mm T-slot and provides a precise fit for standard 24 mm machine-table profiles. Which bolt or thread size is suitable for fastening? This T-nut uses an M20 internal thread and is compatible with standard M20 bolts or studs for secure clamping. What does strength class 10 mean for application? Strength class 10 indicates higher tensile and yield capacity; this AMF T-nut offers robust fixation and reduced deformation under high preload. Is the component compliant with industry standards? Yes — the part is manufactured to DIN 508, ensuring interchangeability and predictable integration into standard T-slot systems. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
250mm Fork Clamp Bar No.6315GN Slotted 22mm For M20 M22 Tension Screw - AMF
Combining a robust fork design, a 22 mm slot width and a 250 mm length delivers stable, repeatable clamping for standard fixtures; compatible with both M20 and M22 clamping screws to reduce setup complexity. Order directly via Metav Werkzeuge or contact our consultants for specification checks. Gabelspanneisen No. 6315GN — Fork clamping wedge, 22 mm slot, 250 mm length (AMF) Gabelspanneisen No. 6315GN is a fork-style clamping wedge designed for secure workholding where standard clamping screws M20 and M22 are used, offering dependable positioning for a variety of workshop fixturing tasks. Fork design No. 6315GN for secure clamping Slot width 22 mm for standard fixtures Length 250 mm for deeper engagement Compatible with M20 and M22 clamping screws Reliable clamping for consistent setups The fork-style clamping wedge provides a straightforward way to convert vertical screw force into lateral clamping pressure, enabling secure fixturing with minimal additional components. The combination of a 22 mm slot and 250 mm length creates a stable contact area that reduces movement during machining or assembly, which improves process repeatability. Where repeatable positioning matters, the wedge form helps maintain alignment without complex adaptations, so changeovers become faster and less error-prone. Fits common screw standards to reduce changeover time Compatibility with both M20 and M22 clamping screws means the component integrates directly into many conventional clamping systems. This cross-compatibility lowers the need for specialised adapters and reduces downtime during tooling swaps. As a result, fixture planning can focus on productivity and cycle time rather than on bespoke hardware, delivering a practical efficiency gain for production and maintenance workflows. Designed for straightforward integration and handling The fork execution simplifies installation: orient the wedge, insert the screw and apply clamping force. Its geometry is aimed at dependable contact and straightforward alignment in vises or fixture assemblies, supporting consistent clamping force transfer. This clarity in function makes it suitable for assembly stations, machining fixtures and general workshop applications where robust, repeatable holding is required without elaborate setup procedures. Confidence in supply and technical support Sourcing components via a dedicated distributor ensures reliable availability and technical guidance. Metav’s role as a precision partner adds an assurance of quality and logistical transparency, backed by stock management from Emmerich. For teams consolidating suppliers or standardising on dependable clamping hardware, the combination of clear compatibility and supply-chain reliability reduces procurement complexity and supports long-term operational stability. Contact Metav Werkzeuge for a tailored specification check on the AMF fork clamping wedge No. 6315GN and advice on integrating it into existing fixtures — Metav Werkzeuge is ready to assist from Emmerich with product and technical support Technical data SKU: 4000833042NW UID: 4000833042NW Type: Fork execution No. 6315GN Product type: Clamping wedge Facts Slot width: 22 mm Length: 250 mm Compatible clamping screws: M20, M22 Package unit: 1 Special features Fork design for lateral clamping force Suitable for standard fixture systems Label: Gabelspanneisen No.6315GN Schlitz-B.22mm L.250mm f.Spannschraube M20,M22 AMF FAQ What is the primary application of this fork clamping wedge? The fork clamping wedge No. 6315GN by AMF is intended for secure workholding and fixture use where a 22 mm slot and 250 mm engagement improve positional stability. Can the wedge be used with both M20 and M22 screws? Yes, the component is compatible with clamping screws M20 and M22, enabling direct integration into common clamping systems. Is this component suitable for heavy-duty machining? The fork design and 250 mm length provide a stable contact area for robust fixturing; suitability for specific heavy-duty operations depends on the broader fixture and machine force. How does the fork geometry affect setup time? Fork geometry simplifies alignment and clamping force transfer, reducing the need for custom adapters and cutting down changeover time in workshop environments. Which SKU should be referenced when ordering or enquiring? Please reference SKU 4000833042NW when requesting availability or technical details for this AMF fork clamping wedge. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
250mm Fork Clamp Bar Slot 18mm For M16 M18 Clamping Screw DIN 6315B - AMF
Take advantage of a standardised fork design and clear dimensional data to streamline fixture assembly and maintenance. With a DIN 6315B specification and a 250 mm overall length the component offers predictable integration into production tooling; order directly via Metav Werkzeuge or consult our specialists for application advice. Fork clamp DIN 6315B – Slot B, 18 mm, 250 mm (AMF) A Fork clamp DIN 6315B engineered for straightforward fixture use and compatible with M16 and M18 clamping screws in industrial and workshop environments. DIN 6315B compatibility 18 mm slot width 250 mm overall length Suitable for M16 and M18 clamping screws Standardised fork design for predictable fixture integration The fork-style clamping bar follows the DIN 6315B specification, which ensures standardised mounting and interchangeability across fixtures. This reduces setup time and simplifies stock management, because components manufactured to common standards fit without modification. The fork geometry, described here as a fork clamp, provides a defined engagement point for clamping screws and locating elements, resulting in consistent positioning during repetitive operations. Where jigs and fixtures rely on repeatable interfaces, this conformity translates into fewer alignment checks and less downtime. Fast compatibility with common clamping screws for flexible setups Designed to accept M16 and M18 clamping screws, the forked clamping bar enables rapid adaptation to existing clamping arrangements. The combination of a 18 mm slot and fork configuration supports secure engagement with a range of screw diameters commonly used in production. For procurement and planning, the clear specification reduces uncertainty: the item is a straightforward solution for retrofitting or expanding clamping systems. If additional dimensional data or advice on screw selection is required, Metav Werkzeuge consultants can provide practical guidance to match the clamping forces and thread standards of the application. Clear dimensions for consistent clamping and maintenance With a 250 mm overall length, the component delivers an extended reach while maintaining a compact footprint suitable for many fixture layouts. The 18 mm slot offers a predictable seating surface that aids in distributing clamping loads and maintaining parallelism between workpiece and fixture. These measurable attributes support quality control and enable quick verification during routine inspection. The fork design also facilitates visual checks for wear or deformation—important for preserving process reliability—so scheduled maintenance can be planned on objective, dimension-based criteria rather than guesswork. For standardised clamping with AMF compatibility and fast supply from Emmerich, contact Metav Werkzeuge for tailored advice and reliable delivery. Technical Data Article number: 4000833028NW Manufacturer: AMF Product type: Clamping bar (fork version) Label: Fork clamp DIN 6315B – Slot B 18 mm L 250 mm for clamping screw M16, M18 Packaging unit: 1 Facts Slot width: 18 mm Overall length: 250 mm Suitable for: M16, M18 SKU: 4000833028NW Special features Standard: DIN 6315B Fork design Slot type: Slot B Brand: AMF FAQ What standard does this clamping bar conform to? The fork clamp conforms to DIN 6315B, providing a standardised interface for fixture and jig integration. Which clamping screws are compatible with the fork design? Compatibility is specified for M16 and M18 clamping screws; the 18 mm slot and fork profile accommodate these common thread sizes. What are the key dimensions to check when retrofitting into an existing fixture? Check the 250 mm overall length and 18 mm slot width to ensure correct reach and engagement with the clamping system; reference SKU 4000833028NW when ordering. Is this product suitable for serial production environments? Yes. The standardised design and clear dimensional specification make the forked clamping bar suitable for repeatable, serial production-fixture setups where interchangeability and predictable performance are priorities. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
250mm Fork Clamp Bar Slot 18mm For M16 M18 Clamping Screw, GN 6315GN - AMF
Take advantage of a fork-style clamping solution that combines precise slot geometry and standard screw compatibility to streamline fixture setup. The 18 mm slot width and 250 mm length ensure adaptable clamping reach and repeatable positioning; order directly via Metav Werkzeuge or request expert advice for system integration. Gabelspanneisen No. 6315GN — Fork clamping bar, slot 18 mm, L 250 mm (AMF) A Gabelausführung No. 6315GN fork clamping bar designed for secure fixture clamping with M16 and M18 clamping screws in workshop and industrial fixturing. Fork design for M16 and M18 clamping screws Slot width 18 mm for standard fixture bars Length 250 mm for versatile clamping reach Robust construction for workshop and industrial use Secure, repeatable clamping with fork geometry The fork-style clamping bar is engineered to provide consistent fixture alignment and stable force transmission when paired with standard clamping screws. The fork design holds the workpiece securely while allowing fast engagement/disengagement during changeovers, which reduces setup time and increases throughput. Compatible with common clamping thread sizes, the component is suited to both manual bench fixtures and automated clamping stations. Clear dimensions to simplify fixture planning Critical dimensions are provided for straightforward integration into existing tooling layouts: the slot width (18 mm) and overall length (250 mm) define the clamping envelope and reach. Additional dimensional references (A: 30; B2: 50; B3: 28; L1: 250; L2: 57; L3: 36) support CAD placement and ensure correct clearance for mating components. These measurable values allow accurate planning of clamp positions and prevent interference during operation. Designed for demanding workshop environments The component is intended for use in production and maintenance settings where reliability matters. The geometry and construction support repeated clamping cycles; this durability reduces the need for frequent replacements and contributes to steady machine availability. The design focuses on practical usability in metalworking and general workshop applications while remaining compatible with standard clamping systems. Easy integration into existing clamping systems Integration is facilitated by compatibility with M16 and M18 clamping screws and the standard 18 mm slot, enabling seamless substitution into common fixture arrangements. The part functions as a modular element within versatile clamping setups, allowing procurement teams to reduce SKUs by selecting a solution that interfaces with a wide range of accessories and screw types. For specification and layout assistance, technical consultation is available. For procurement or technical advice on the AMF fork clamping bar, contact Metav Werkzeuge in Emmerich for tailored assistance and reliable supply coordination via phone or email. Technical data Article number: 4000833041NW Model: Gabelausführung Nr. 6315GN Product type: Clamping bar Brand: AMF Packaging unit: 1 Facts Slot width: 18 mm Overall length: 250 mm A: 30 mm B2: 50 mm B3: 28 mm L1: 250 mm L2: 57 mm L3: 36 mm Compatible threads: M16, M18 Special features Fork version for positive engagement Standard slot for fixture compatibility Suitable for workshop and industrial fixturing Modular integration with clamping screws and accessories FAQ Which clamping screws are compatible with this fork clamping bar? The fork clamping bar is compatible with M16 and M18 clamping screws; refer to model No. 6315GN (SKU 4000833041NW) when specifying the thread interface. What are the slot width and overall length? The slot width is 18 mm and the overall length is 250 mm, dimensions that define the clamping envelope for fixture planning. Can this component be used in automated clamping stations? Yes; the fork design and standard dimensions allow integration into both manual fixtures and automated clamping systems for repeatable positioning. Which measurements aid CAD integration and mounting? Use the provided dimensional references (A: 30; B2: 50; B3: 28; L1: 250; L2: 57; L3: 36) to place the part accurately in assemblies and to verify clearances. How should the item be referenced when ordering or specifying? Reference the AMF fork clamping bar by model No. 6315GN and SKU 4000833041NW to ensure the correct part and dimensions are supplied. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
250mm Fork Clamp Iron No. 6315GN Slotted Jaw 26mm For M24 Clamping Screw, Addition A40 B2:70 B3:43 L1:250 L2:83 L3:56 - AMF
Take advantage of the fork design, 26 mm slot width and 250 mm overall length for dependable fixture clamping and straightforward integration into standard setups; Order the fork clamping wedge No. 6315GN directly via Metav Werkzeuge or ask our consultants if needed Fork clamping wedge No. 6315GN — Fork version clamping wedge with 26 mm slot and 250 mm length (AMF) The Fork clamping wedge No. 6315GN is a fork-style clamping wedge engineered for fixture and workholding applications with M24 clamping screws, combining a narrow slot profile with extended engagement length for stable part retention Fork design for secure clamping Slot width 26 mm for standard fixtures Length 250 mm for deep engagement Reliable holding power for fixture work The fork-style geometry offers a direct mechanical advantage: the fork design centres clamping force around the screw axis and provides a consistent contact surface. With a 26 mm slot width and compatibility with M24 clamping screws, this clamping wedge is intended for standardised fixture systems and simple retrofitting. The result is a predictable clamping behaviour that reduces setup time and ensures repeatable component positioning. Technical users will value the clear interface to existing clamping screws and the improved load distribution compared with single-point clamps. Dimensions that simplify integration and alignment Precise dimensions enable straightforward planning for jigs and fixtures: the overall engagement length 250 mm (L1) combines reach with rigidity, while the additional measured values (A: 40; B2: 70; B3: 43; L2: 83; L3: 56) describe the wedge geometry for correct seat and clearance design. These figures allow engineers to calculate lever arms and contact points accurately so that clamping forces are applied where intended. The measured geometry also supports CAD-based checks, avoiding trial-and-error on the shop floor and accelerating fixture build times. Robust workshop suitability and consistent performance Designed as a practical component for industrial workholding, the clamping wedge is supplied as a single unit for immediate use and is brand-marked by AMF. The straightforward construction focuses on reliable mechanical function and long service intervals when used within specified parameters. For procurement and tooling consolidation, the component integrates cleanly into a wider clamping system and supports stable production runs. If additional specification data or compatibility checks are required, technical advice is available to confirm fit and function in specialised setups. Contact Metav Werkzeuge for tailored specification support on the AMF fork clamping wedge No. 6315GN — phone +49 2822 7131930 or eMail info@metav-werkzeuge.com for prompt assistance and advice Technical data Article number: 4000833043NW SKU: 4000833043NW Type: Fork version No. 6315GN Label: Fork clamping wedge No.6315GN slot W.26mm L.250mm for clamping screw M24 AMF Brand: AMF Data Slot width: 26 mm L1 (overall length): 250 mm A: 40 B2: 70 B3: 43 L2: 83 L3: 56 Special features Product type: Clamping wedge Suitable for: M24 clamping screws Packaging unit: 1 UID: 4000833043NW FAQ What clamping screw size fits this wedge? The fork clamping wedge No. 6315GN is designed for use with M24 clamping screws and mates directly with standard M24 fixture hardware. What is the slot width and why does it matter? The wedge features a 26 mm slot width, which determines compatibility with mating fixture elements and ensures correct seating and force distribution during clamping. How long is the wedge and what does that mean for engagement? The overall engagement length is 250 mm (L1); this extended length increases contact area and enables deeper engagement in fixture assemblies for improved stability. Is the component supplied as a single unit? Yes, the AMF fork clamping wedge No. 6315GN is supplied as a single unit (packaging unit: 1) ready for immediate installation. Manufacturer: AMF; Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
250mm Fork Jaw Clamp Bar Slot 22mm For M20 M22 Clamping Screw DIN 6315B - AMF
Take advantage of a standard-compliant clamping solution that combines secure engagement and broad compatibility for efficient workshop workflows; the fork-style design and 22 mm slot work together to reduce setup time and simplify spare-part management — order via Metav Werkzeuge or ask their consultants for application advice. Fork-style clamping wedge DIN 6315B – 22 mm slot, 250 mm (AMF) A fork-style clamping wedge DIN 6315B for machine-table and fixture clamping, designed to accept M20 and M22 clamping screws for standardised, repeatable set-ups Fork design for secure clamping DIN 6315B standardised compatibility 22 mm slot for broad clamping range 250 mm length for deep workpieces Consistent, standardised clamping for production environments The DIN 6315B specification ensures interchangeability across fixtures and clamping systems, which reduces procurement complexity and downtime. As a fork-style clamping wedge, this component provides a reliable interface between the clamping screw and workpiece support; the 22 mm slot allows a wider range of jaw and bracket geometries to be engaged. In practical terms, conformity to the standard translates into predictable performance during repeat production runs and faster changeovers on the shop floor. Compatibility that speeds set-up and reduces inventory Designed to accept common thread sizes M20 and M22, the wedge eliminates the need for multiple specialised adapters. Fewer bespoke parts mean simplified inventory and quicker assembly: maintenance teams benefit from reduced search time and purchasing departments from lower SKUs. The specification-driven approach supports leaner stocking while maintaining flexibility for varied clamping tasks, making it suitable for both single-machine workshops and production lines. Robust engagement for secure workholding The fork design achieves positive engagement with the clamping screw, translating clamp force efficiently into holding power at the point of contact. This geometry improves stability during machining and finishing operations where consistent clamping pressure is required. The 250 mm overall length extends the usable reach of the clamping element, allowing secure support of longer or irregularly shaped workpieces without compromising access for tools or inspection. Practical benefits for workshop efficiency Using a standardised, heavy-duty clamping element simplifies both planning and daily operation. The clear specification (slot width 22 mm, length 250 mm) enables quick selection of complementary components and avoids ambiguous fittings that can interrupt production. For technicians and engineers, the component’s straightforward design reduces assembly steps and facilitates routine checks, contributing to steady throughput and fewer unplanned stops. For robust, standard-compliant clamping solutions from AMF, contact Metav Werkzeuge in Emmerich for tailored advice and reliable supply of compatible components. Technical data Article number: 4000833030NW Label: Gabelspanneisen DIN 6315B Schlitz-B.22mm L.250mm f.Spannschraube M20,M22 AMF Manufacturer: AMF Facts Slot width: 22 mm Overall length: 250 mm Suitable for: M20, M22 Packaging unit: 1 Special features Fork design Standard: DIN 6315B Product type: clamping wedge axite enrichment: A: 40; B2: 62; B3: 20; B4: 10 FAQ What clamping screw sizes does this wedge accept? The fork-style clamping wedge is specified for M20 and M22 clamping screws, ensuring compatibility with common machine-clamping hardware. Does the component comply with recognised standards? Yes, the element is manufactured to DIN 6315B, which supports interchangeability and predictable performance in fixture assemblies. What is the usable slot width and overall length? The wedge features a 22 mm slot width and an overall length of 250 mm, providing extended reach for deeper workpieces. Is this part suitable for series production and quick changeovers? The standardised design and common thread compatibility make the wedge well suited to series production, where repeatability and rapid set-up are priorities. How does the fork design improve clamping performance? The fork geometry ensures positive engagement with the clamping screw and directs clamp force effectively to the workpiece, improving stability during machining. Manufacturer: AMF; Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
250mm Fork Jaw Clamp Bar Slot B26mm For M24 Clamping Screw, DIN 6315B - AMF
Combine DIN 6315B conformity with a 26 mm fork slot and direct compatibility with M24 clamping screws to ensure consistent fixture alignment and faster setup; order the AMF fork clamp bar directly via Metav Werkzeuge or consult the technical team for integration advice. AMF Fork-Style Clamp Bar DIN 6315B — 26 mm Slot, 250 mm Length The AMF Fork-Style Clamp Bar DIN 6315B is a forked clamping bar designed for fixture and clamping systems, providing standardised mounting and secure engagement with M24 clamping screws. DIN 6315B compliant fork design 26 mm slot width for standard fixtures 250 mm overall length for versatile reach Compatible with M24 clamping screws Secure, standardised engagement for reliable fixtures The fork configuration delivers a positive mechanical engagement with clamping screws and fixture components, increasing repeatability in production and jig setups. Built to the DIN 6315B standard, this clamp bar supports interchangeability across systems that rely on standardised dimensions. The 26 mm slot width provides a defined seating for forks and keys, while the 250 mm overall length balances reach and stiffness for common workshop tasks. These characteristics reduce the need for custom adapters and simplify the alignment process in repetitive operations. Faster setup through measured compatibility and fewer adjustments Standard dimensioning and the intended fit for M24 clamping screws reduce setup time and minimise trial adjustments during changeovers. Where fixtures are exchanged frequently, the predictability of standard parts decreases downtime and streamlines assembly sequences. The fork variant ensures quick insertion and positive location, which is especially useful in modular clamping systems and routine production runs. This measured approach to compatibility supports more efficient workshop workflows and a lower error rate at the fixture stage. Practical integration for workshop and production environments Designed as a single, ready-to-fit component, the fork clamp bar suits both bench-level jigging and larger fixture assemblies in production. The fork-style clamp bar from AMF is supplied as an individual item, making it straightforward to replace or expand existing clamping arrays without overhauling the entire system. Its straightforward geometry allows easy inspection and verification of seating and wear, supporting predictable maintenance cycles and safer clamping conditions on the shop floor. For standardised, fork-style clamping choose the AMF fork clamp bar via Metav Werkzeuge — contact Metav Werkzeuge for technical guidance and prompt supply from Emmerich: info@metav-werkzeuge.com | +49 2822 7131930 Technical data Article number / SKU: 4000833033NW Type: Fork version Standard: DIN 6315B Product type: Clamp bar Slot width: 26 mm Overall length: 250 mm For clamping screw: M24 Manufacturer: AMF Packaged units: 1 Core data Slot width: 26 mm Total length: 250 mm For: M24 clamping screws Packaged units: 1 SKU: 4000833033NW Special features Fork-style execution for positive engagement DIN 6315B standardised dimensions Suitable for fixture and jig integration Supplied as single unit for easy replacement Axite enrichment values: A: 40; B2: 66; B3: 20; B4: 10 FAQ Is this clamp bar compatible with M24 clamping screws? Yes. The AMF fork clamp bar is designed specifically for use with M24 clamping screws and mates with standard M24 threaded clamping systems. What standard ensures interchangeability for this component? The clamp bar conforms to DIN 6315B, which ensures standardised dimensions and interchangeability within compatible fixture systems. What are the key dimensions to check before ordering? Check the fork slot width of 26 mm and the overall length of 250 mm to ensure fit with existing fixture components and required reach. How is the AMF fork clamp bar supplied? The product is supplied as a single unit (packaged unit: 1), suitable for direct replacement or integration into modular clamping setups. Where is this clamp bar typically used? This fork-style clamp bar is used in jigs, fixture systems and production clamping assemblies where standardised, repeatable clamping is required. Manufacturer: AMF; Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
250mm Stud Bolt M16 Heat Treated 8.8 DIN 6379 - AMF
The combination of DIN 6379 conformity, an M16 thread and a 250 mm overall length ensures reliable mechanical fastening and straightforward parts interchangeability; tempered to strength class 8.8, the fastener delivers consistent clamping performance for industrial assemblies. Order the stud bolt directly via Metav Werkzeuge or ask our consultants if needed. Stud bolt DIN 6379 M16 x 250 mm, tempered to 8.8 — AMF A Stud bolt DIN 6379 M16 x 250 mm tempered to 8.8 (AMF) for secure, standardised mechanical joins in workshop and industrial applications Conforms to DIN 6379 standard M16 thread for robust connections Tempered to strength class 8.8 Hex drive width 19 mm for controlled torque Consistent performance for structural fastenings Conformity with DIN 6379 guarantees that this stud bolt fits established machine and assembly standards, which simplifies spare-part management and reduces downtime. The M16 thread paired with the 250 mm overall length provides a long engagement depth that is suitable for bolting through thick assemblies, while the tempered treatment to class 8.8 increases tensile strength and yield characteristics. This combination is designed for repeatable clamping force, which helps maintain joint integrity under cyclic loads and routine maintenance. Precision features that aid efficient installation The external thread form and the hex 19 mm drive interface enable reliable torque transmission during tightening, so the joint can be tensioned predictably. These characteristics, when used with calibrated torque tools, reduce the risk of over- or under-tightening and contribute to consistent assembly quality. The item’s adherence to an established norm allows planners to specify the fastener in CAD and parts lists with confidence, facilitating procurement and ensuring compatibility across production batches. Clear specification and supply details for purchasing Technical transparency is provided through the clear labelling of standard, thread size and strength class, which streamlines material approvals and quality checks. The product is supplied as a single unit, labelled for traceability and inventory control. The SKU 4000833277NW and the visible marking of 8.8 tempering support documentation for quality records, and purchasing teams benefit from immediate identification when ordering replacements or matching components. For application advice or to secure stock of AMF stud bolts, contact Metav Werkzeuge’s technical team and order through their procurement channel for prompt, reliable supply Technical data Article number: 4000833277NW Product: Stud bolt Brand: AMF Standard: DIN 6379 Facts Thread: M16 Overall length: 250 mm Hex width: 19 mm Strength class: 8.8 Packaging unit: 1 Special features Tempered to strength class 8.8 Conforms to DIN 6379 Single-piece supply Marked SKU for traceability FAQ What does strength class 8.8 mean for load capacity? Strength class 8.8 indicates a quenched and tempered bolt with enhanced tensile and yield properties compared with lower classes; the AMF stud bolt graded 8.8 is intended for demanding mechanical joints where reliable clamping is required. Is this stud bolt compatible with metric nuts and standard components? Yes, the Stud bolt DIN 6379 M16 x 250 mm tempered to 8.8 (AMF) is made to the DIN 6379 specification and is compatible with standard M16 nuts and mating parts manufactured to the same norm. How should the bolt be tightened to achieve correct clamping? Use a calibrated torque or tensioning tool and apply the manufacturer-recommended torque for M16 threads and strength class 8.8; controlled torque ensures the AMF stud bolt achieves the intended preload without overstressing the assembly. What is delivered in one packaging unit? Packaging unit 1 contains one AMF stud bolt, clearly labelled with SKU 4000833277NW for inventory and quality-traceability purposes. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
250mm Stud Bolt M20 Hardened Grade 8.8 DIN 6379, Threaded Length 160mm - AMF
Take advantage of a robust, DIN‑compliant fastening solution: the combination of DIN 6379 standardisation and property class 8.8 heat treatment ensures dependable clamp strength and consistent assembly performance; order directly via Metav Werkzeuge or consult our specialists for precise application advice. AMF Stud Bolt DIN 6379, M20 x 250 mm, Class 8.8 A AMF stud bolt (DIN 6379) designed for heavy‑duty fastening in mechanical assemblies, flanged joints and structural connections. Heat‑treated to property class 8.8 Conforms to DIN 6379 standard M20 metric thread for robust connections 250 mm overall length for deep assemblies Reliable connections for demanding assemblies The AMF stud bolt delivers a focused solution where repeatable, high‑strength joints are required. Conformance to DIN 6379 guarantees dimensional compatibility with matching nuts and components, reducing assembly errors and rework. The metric M20 thread, combined with the specified overall length of 250 mm, allows for secure engagement in flanged unions or layered assemblies. For production planners and maintenance engineers, this translates into shorter fitting times and predictable torque behaviour during tightening. Strength and material treatment explained Specified as property class 8.8, the fastener benefits from heat treatment that raises tensile strength and yield characteristics compared with untreated bolts. In practice, this means the stud is suitable for structural and mechanical applications that demand medium‑high strength without resorting to alloy or special‑grade fasteners. Compliance with DIN 6379 ensures that the fastener’s mechanical attributes and thread form meet established industrial tolerances, facilitating interchangeability across suppliers and simplifying procurement specifications. Application notes and installation benefit The stud’s length and thread size make it suitable for deep or multi‑layer assemblies where standard bolts would not provide sufficient engagement. A width value of 27 mm supports the use of standard spanners or sockets for installation, enabling consistent torque application and easier on‑site handling. Where downtime or alignment sensitivity is a concern, adopting a DIN‑based stud reduces the risk of incorrect part selection and contributes to stable joint life cycles, lowering maintenance frequency and supporting predictable production throughput. For assured supply and expert guidance on integrating AMF fasteners into industrial assemblies, contact Metav Werkzeuge in Emmerich at info@metav-werkzeuge.com or +49 2822 7131930 to discuss specifications and availability Technical data Article number: 4000833286NW Manufacturer: AMF Product type: Stud bolt Standard: DIN 6379 Packaging unit: 1 Core measurements Thread: M20 Overall length: 250 mm Width: 27 mm Addition: b: 160 Special features Heat‑treated to property class 8.8 Conforms to DIN 6379 Suitable for use in bolted and flanged connections FAQ What applications suit this stud bolt best? The stud bolt is intended for mechanical assemblies, flanged joints and structural connections where a DIN 6379‑compliant, heat‑treated fastener is required; the SKU 4000833286NW identifies this specific AMF item. How does property class 8.8 influence performance? Property class 8.8 indicates a heat‑treated medium‑high strength fastener; in practice, the AMF stud bolt provides reliable tensile and yield behaviour for many industrial fastening jobs without requiring specialised alloy grades. Is the thread form compatible with standard nuts and tools? Yes — the M20 metric thread follows standard thread specifications and pairs with standard M20 nuts and common spanner or socket sizes for secure tightening. Can this fastener be used in multi‑layer or deep assemblies? With an overall length of 250 mm, the stud is well suited to deeper stacks and multi‑layer joints, allowing sufficient thread engagement for robust clamping. What does DIN 6379 guarantee for procurement teams? DIN 6379 conformity ensures dimensional interchangeability and adherence to established industrial tolerances, simplifying supplier selection and quality assurance when specifying the AMF stud bolt (SKU 4000833286NW). Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com