Unsere aktuellen Angebote

The combination of a 3 W COB LED for wide-area illumination, a 3.8 V 1600 mAh Li‑Ion Polymer power supply and a contactless sensor switch ensures reliable, hands-free lighting for workshop tasks; order the headlamp directly via Metav Werkzeuge or consult their advisers for application guidance. LED headlamp 3.8V 1600 mAh (3 W) – TECWERK The LED headlamp 3.8V 1600 mAh (3 W) is a sensor-operated, hands-free light engineered for workshop maintenance, inspection and on-the-job repair where clear, wide-area illumination and simple operation are essential 3 W COB LED for high light output Two switchable brightness levels Touchless sensor for hands-free control Clear illumination that speeds up tasks The lamp uses a COB LED delivering a concentrated yet even beam that covers the immediate work area, reducing the need for repeated repositioning and enabling precise visual inspection. With two switchable brightness levels, lighting can be adapted to fine detail work or broader area tasks, which improves efficiency and reduces eye strain. The design focuses on usable output rather than marketing figures, giving a practical solution for routine maintenance and assembly work. Sensor control for uninterrupted workflow A touchless switch with sensor function allows the light to be turned on or off with a simple hand movement, so the light remains usable while wearing gloves or handling tools. The sensor operation supports genuine hands-free working and reduces contamination of controls in dirty or oily environments. This intuitive control method shortens task time and keeps focus on the process rather than on fiddly switches. Recognisable battery status and dependable power Power is supplied by a 3.8 V, 1600 mAh Li‑Ion Polymer battery that is lightweight and compact yet sufficiently rated for typical maintenance periods. A clear LED battery charge indicator signals charging progress — red while charging and green when charging is complete — so battery status is immediately visible and planning for recharging becomes straightforward. The battery technology chosen balances energy density and practical service life for frequent use. Ready for workshop routines and simple storage Supplied in blister packaging, the lamp is compact to store and easy to pick up for single-person use or as part of a tool kit. The robust, no-frills construction and sensor operation make it suitable for mechanics, electricians and maintenance engineers who need dependable, hands-free lighting without complicated setup. The product integrates easily into established toolrooms and is suitable as a routine spare for mobile service teams. Choose TECWERK’s sensor-controlled headlamp for safer, more efficient workshop lighting — contact Metav Werkzeuge in Emmerich for ordering or technical advice at info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: 2000877173NW Label: LED headlamp 3.8V 1600 mAh 1x Li‑Ion Polymer 3 W Blister packaging TECWERK Packaging unit: 1 Core specifications Power: 3 W Light source: COB LED Battery: 3.8 V, 1600 mAh Li‑Ion Polymer Modes: Two brightness levels Special features Touchless sensor on/off LED battery charge indicator (red = charging, green = charged) Hands-free operation suitable for workshops Blister packaging for simple storage and retail display FAQ How is the light intensity adjusted? The lamp offers two switchable brightness levels; adjustment is made via the built-in control so the light output can be adapted to detailed or broad tasks. Does the lamp indicate charging status? Yes, the LED battery charge indicator shows red during charging and green when charging is complete for immediate status recognition. Which battery type is used and is it replaceable? A 3.8 V, 1600 mAh Li‑Ion Polymer battery is fitted; the specification and maintenance instructions are provided with the device. Is the headlamp suitable for workshop use with gloves? The touchless sensor allows operation without direct contact, enabling use while wearing gloves and during hands-on tasks. What is the product SKU for ordering? Ordering can be referenced by SKU 2000877173NW for the TECWERK LED headlamp. Manufacturer / Responsible: NORDWEST Handel AG, Robert-Schuman-Straße 17, 44263 Dortmund

Reliable hybrid LED lighting that combines high luminous output, flexible power sources and robust protection for the workshop and site. Benefit from the 47 W / 5,500 lm performance and mains‑to‑battery automatic switchover — order via Metav Werkzeuge or contact our consultants for application advice. TECWERK Multi Battery Hybrid LED Floodlight — 47 W, 5,500 lm, IP54 The TECWERK Multi Battery Hybrid LED Floodlight is a versatile site and workshop light for mains or 18 V battery use, offering reduced glare and integrated powerbank functionality. Compatible with 18 V batteries from major brands Switches automatically between mains and battery Integrated USB output for powerbank use Dimmable: 100% / 50% / 25% settings IP54 splash‑proof, shock‑ and dust‑resistant Continuous illumination for uninterrupted workflows The hybrid worklight delivers a 47 W rating and 5,500 lm luminous flux for reliable, bright illumination in demanding environments. Designed for compatibility with common 18 V tool batteries (Bosch, Makita, Milwaukee, DeWalt, CAS/Metabo), the unit switches automatically from mains to battery operation to maintain light during power interruptions. The integrated USB output serves as a powerbank, enabling device charging on site, while the reported run time of 1.5–6.5 h (depending on battery capacity and dim setting) supports extended tasks without frequent battery changes. Clear, daylight‑balanced light that reduces fatigue The fixture produces a neutral 5,000 K light colour and a wide 120° beam angle to cover work areas evenly. An opal diffuser reduces glare and softens the beam for more comfortable visual conditions, which helps to minimise eye strain during precision tasks. With an expected service life of 50,000 h, the lamp maintains consistent colour and output over prolonged use, reducing maintenance cycles and ensuring steady illumination for inspection, assembly or general workshop activities. Robust design with safety and handling in mind Built to withstand jobsite conditions, the unit is rated IP54 for splash and dust protection and is described as shockproof. Practical features include a removable H07RN‑F cable (5 m, 3G1.5 mm²), a rear protective‑earth plug and a clear charge indicator for immediate status checks. The three‑step dimmable control (100% / 50% / 25%) extends runtime when required, and automatic mains/battery switchover functions as an emergency lighting safeguard. Compliance with BGI 608 K2 underlines its suitability for professional applications that demand documented safety standards. Choose the TECWERK hybrid floodlight for dependable, flexible site lighting and contact Metav Werkzeuge for tailored application advice or ordering — eMail: info@metav-werkzeuge.com | Tel: +49 2822 7131930 Technical data Article number: 2000873433NW Product: TECWERK Multi Battery Hybrid LED Floodlight (translated) Packaging unit: 1 Brand: TECWERK Numbers / Core technical data Power: 47 W Light output: 5,500 lm Colour temperature: 5,000 K Beam angle: 120° Service life: 50,000 h Run time: 1.5–6.5 h Special features / Versions Compatibility: 18 V batteries (Bosch, Makita, Milwaukee, DeWalt, CAS/Metabo) Protection class: IP54 Cable: H07RN‑F 5 m 3G1.5 mm² (removable) Lighting control: Dimmable 100% / 50% / 25% Diffuser: Opal, glare‑reduced USB output: Integrated powerbank function Safety: Automatic mains/battery switchover Certification/standard: BGI 608 K2 Tested: Yes (prüfpflichtig) FAQ What power sources can be used with this floodlight? The floodlight accepts mains power or 18 V tool batteries; it is compatible with Bosch, Makita, Milwaukee, DeWalt and CAS (Metabo) battery systems and switches automatically between mains and battery operation. How long will the light run on battery? Run time ranges from 1.5–6.5 h, depending on the battery capacity used and the selected dimming setting on the TECWERK hybrid floodlight. Is the light suitable for outdoor worksites? Yes. The unit is rated IP54 for protection against dust and splashing water and is described as shock‑resistant, making it suitable for many outdoor and site applications. Can the lamp charge mobile devices? An integrated USB output provides a powerbank function so small devices can be charged directly from the floodlight while on site. Does the light reduce glare for close‑up tasks? The opal diffuser softens the beam and reduces direct glare, delivering a more even, comfortable light that supports precision work and visual inspection. Manufacturer/Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund

Take advantage of a compact, robust 50 W lighting solution that combines high luminous output with practical mobility; the integrated 5200 mAh Li‑Ion battery and powerbank function ensure continued operation and device charging on site. Order the unit directly via Metav Werkzeuge or contact their consultants for tailored advice. TECWERK LED Floodlight 50 W – 800–4,500 lm, 14.8 V Li‑Ion, IP54 The TECWERK LED Floodlight 50 W is a portable worklight designed for workshop and site use, offering adjustable beam control and a built‑in powerbank for versatile illumination and device charging. 120 SMD LEDs for even illumination Adjustable beam: vertical 90° and horizontal 180° Integrated powerbank function for device charging IP54 housing and practical handle for site use Reliable, high‑output lighting for professional tasks The compact lamp delivers 800–4,500 lm from 120 SMD LEDs driven by 50 W of power, providing a choice between concentrated and broad illumination depending on the task. The internal 5200 mAh Li‑Ion battery at 14.8 V keeps the unit operational where mains access is limited, while the IP54 rating protects against dust and splashing water—suitable for demanding workshop and outdoor applications. The spec-driven design supports productivity by offering a strong, consistent light source that helps maintain workflow under variable site conditions. Precise illumination and comfortable colour rendering Thanks to the adjustable beam (vertical 90° and horizontal 180°) the lamp can be set for targeted task lighting or wide-area coverage, reducing the need for multiple fixtures. The neutral 5700 K colour temperature yields daylight‑like illumination that supports accurate visual inspection and reduces eye strain during fine work. These characteristics make the light appropriate for preparatory tasks, inspections and any situation where both intensity and colour fidelity matter. Practical features for everyday site use Built with a robust housing and a practical handle, the worklight is engineered for portability and frequent handling on site. The unit includes a visible battery indicator to monitor charge status and a powerbank function to recharge mobile devices or tools, adding operational flexibility. With a typical recharge time of approx. 3.5 h, the lamp is ready for repeated use after a short downtime. The device is noted as subject to inspection, ensuring that periodic safety checks and documentation are supported for professional environments. For technical advice or to request a tailored supply, contact Metav Werkzeuge – Metav’s specialists can advise on matching illumination solutions to specific workshop or site requirements; reach them at info@metav-werkzeuge.com or +49 2822 7131930 Technical data SKU: 2000873354NW Model: TECWERK LED floodlight 50 W 800–4,500 lm Brand: TECWERK Core figures Power: 50 W Light output: 800–4,500 lm LEDs: 120 SMD Battery: 5,200 mAh, 14.8 V Li‑Ion Colour temperature: 5,700 K Charge time: approx. 3.5 h Beam angles: vertical 90°, horizontal 180° Protection class: IP54 Inspection required: yes Special features Adjustable beam Battery indicator Robust housing and practical handle Powerbank function Universal, portable use FAQ What is the typical light output range of this worklight? The worklight provides a variable light output between 800 and 4,500 lumens, enabling both focused task lighting and broad area illumination. How long does the battery take to recharge? The internal battery of the TECWERK LED Floodlight recharges in approximately 3.5 hours under normal charging conditions. Can the unit be used in wet or dusty environments? The floodlight has an IP54 protection rating, which makes it resistant to dust ingress and splash water—suitable for most site and workshop conditions. Does the light offer device charging capability? Yes, the integrated powerbank function allows the floodlight to supply power to USB‑charged devices, adding practical on‑site utility. Is a safety inspection required for this product? The product is listed as inspection required, meaning it should be included in regular safety and electrical checks as per workplace regulations. Manufacturer/Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund

Take advantage of the combination of precise CVD AC820P coating performance, a positive 80° C‑rhombus geometry and a 0.8 mm corner radius for consistent finishing results; order the insert directly via Metav Werkzeuge or request application advice from the consultants. Sumitomo CCMT09T308N-SU AC820P – Positive 80° turning insert for finishing steel A Sumitomo CCMT09T308N-SU AC820P turning insert engineered for finishing and light external and internal turning of steel in continuous to lightly interrupted cuts CVD-coated AC820P for balanced wear resistance Positive 80° C‑rhombus geometry for fine finishing SU chipbreaker for light, one-sided chips Two usable cutting edges; 0.8 mm corner radius Stable surface finish through positive geometry The positive C‑rhombus 80° form paired with a small 0.8 mm corner radius promotes a consistently fine surface on turned components. The insert’s positive rake and neutral cutting direction reduce cutting forces, which benefits smaller lathes and lighter set-ups by lowering vibration and improving repeatability. This geometry is particularly suited to finishing passes where surface integrity and dimensional stability are priorities. Balanced wear and fracture resistance for steady productivity Coated with a CVD Super‑FF layer (Al₂O₃/TiCN) of approximately 14 µm and a substrate hardness of 90.1 HRA, the grade delivers an even compromise between wear resistance and toughness. The measured bending strength of 2.2 GPa supports resistance against fracture in continuous to lightly interrupted cuts, making the insert a dependable choice for production runs requiring long tool life and fewer tool changes. Controlled chip formation and predictable cutting window The single‑sided SU chipbreaker and a slightly positive chip angle (approx. 8°) generate short, manageable chips for finishing operations. Recommended cutting parameters span ap 0.5–2.5 mm and feed f 0.07–0.30 mm/rev (optimum 0.20 mm/rev), with cutting speeds Vc 190–310 m/min (optimum 250 m/min) for steel applications. These ranges help to set up processes quickly and achieve repeatable component quality. Practical design for everyday turning tasks A cylindrical hole with a single countersink and a plate thickness of 3.97 mm ensure stable clamping and reliable seat location in standard toolholders. Two usable cutting edges extend the economical life of each indexable plate, while the neutral feed direction and positive geometry keep cutting forces moderate. The insert is supplied in practical packaging units of 10 pieces, facilitating workshop inventory management. For application advice or stock information on Sumitomo turning inserts, contact Metav Werkzeuge by e‑mail at info@metav-werkzeuge.com or by phone on +49 2822 7131930 Technical data Article number: 207108 Manufacturer article number: 207108 SKU: 207108-Sumitomo Product name: Sumitomo CCMT09T308N-SU AC820P Wendeschneidplatte Product type: Indexable insert for turning Brand: Sumitomo Origin: Japan Facts Substrate hardness: 90.1 HRA Layer thickness: approx. 14 µm Bending strength: 2.2 GPa Plate thickness: 3.97 mm Cutting edge length: 9.7 mm Inner circle diameter: 9.525 mm Cutting angle / tip angle: 80° Clearance angle: 7° Corner radius: 0.8 mm Usable cutting edges: 2 Recommended cutting speed Vc: 190–310 m/min (optimum 250 m/min) Feed range f: 0.07–0.30 mm/rev (optimum 0.20 mm/rev) ap range: 0.5–2.5 mm Pack unit: 10 pieces Tolerance class: M Special features Material: Cemented carbide, CVD-coated (Super‑FF, Al₂O₃/TiCN) Grade: AC820P (universal CVD sort for steel) Chipbreaker: SU – light, one-sided chip control Plate form: C‑Rhombus 80° (positive) Plate size: 09T3 (CCMT09T308N‑SU) Hole style: Cylindrical hole with single countersink Cutting direction: Neutral Application: Finishing to light external and internal turning of steel; continuous to slightly interrupted cuts Limitations: Not intended for heavy interrupted cuts, aggressive roughing or primarily stainless steel applications Suitability: Two usable cutting edges; positive rake angle approx. 8° FAQ What applications suit this turning insert best? The insert is designed for finishing and light external and internal turning of steel, performing well in continuous to slightly interrupted cuts; it is specified as a Sumitomo CCMT09T308N‑SU AC820P turning insert. Which cutting speeds and feeds are recommended? For the AC820P grade, use Vc 190–310 m/min (optimum 250 m/min) with feeds of 0.07–0.30 mm/rev (optimum 0.20 mm/rev) and ap between 0.5–2.5 mm for typical steel finishing tasks. What benefits does the CVD AC820P coating provide? The CVD AC820P coating (Al₂O₃/TiCN) offers a balanced combination of wear resistance and toughness, assisting long tool life and stable performance in finishing operations on steel. Can the insert be used for interrupted cuts? Yes, the insert tolerates light interruptions in cutting; however, it is not intended for heavy interrupted cuts or aggressive roughing where a more fracture‑resistant grade would be required. How many effective edges does each plate provide? Each plate offers two usable cutting edges, which supports economical indexation and reduces tooling costs in serial production. Manufacturer: Sumitomo Electric Hardmetal Corp.; 1‑1‑1 Koyakita, Itami, Hyogo 664‑0016; in Itami Works of Sumitomo Electric Industries, Ltd.

Benefit from the combination of CVD-coated carbide durability and an ISO‑standard geometry that ensures reliable holder compatibility; the plate’s T9215 grade delivers wear resistance and fracture toughness for productive medium‑steel turning. Order the insert directly via Metav Werkzeuge or consult our advisors for application guidance. CNMG 120404-TM T9215 — ISO CNMG120404 rhombic turning insert, CVD‑coated carbide, 0.4 mm corner radius (Tungaloy) A CNMG 120404-TM T9215 indexable turning insert engineered for medium steel turning, offering high wear resistance and consistent performance in continuous to lightly interrupted cuts. CVD-coated carbide grade T9215 ISO CNMG 120404 rhombic geometry 0.4 mm corner radius for fine finish Double-sided chipbreaker with cylindrical hole Productivity with reliable wear resistance The T9215 grade is a CVD‑coated carbide designed to balance wear resistance and fracture toughness, making it particularly effective for medium steel machining. This combination allows stable cutting at elevated feed rates and supports high productivity in continuous to lightly interrupted operations. The coating reduces flank and crater wear, extending effective tool life and lowering changeover frequency, which benefits batch production and longer turning cycles. Precise ISO geometry for straightforward toolholder matching The insert follows the ISO CNMG120404 specification with a rhombic 80° included angle and 0° relief angle, which simplifies selection of the corresponding holder. Compatibility is determined by form, relief angle, tolerance class, fastening method, size and thickness; ensuring these parameters match the toolholder avoids setup errors and contributes to consistent cutting conditions. The ISO conformity aids tool management and inventory control across multiple machines. Controlled surface quality and cutting stability With a 0.4 mm corner radius, the plate offers a favourable compromise between edge strength and surface finish: small radii help achieve finer finishes while maintaining edge integrity under moderate feeds. The double‑sided chipbreaker supports predictable chip formation and evacuation, while the cylindrical central hole and 4.76 mm thickness ensure secure clamping in standard CNMG holders. Together, these features reduce vibration, improve repeatability and support efficient finishing passes. For high‑productivity turning with Tungaloy’s T9215 grade, contact Metav Werkzeuge for tailored advice or to place an order — email info@metav-werkzeuge.com or call +49 2822 7131930 to discuss suitability for specific steel grades and machining conditions Technical data Article number: 6772176 Manufacturer SKU: TUN6772176 SKU: 6772176-Tungaloy Label: CNMG 120404-TM T9215 Facts Corner radius: 0.4 mm Included angle: 80° Relief angle: 0° Plate thickness: 4.76 mm Plate size: 12 mm Special features Material: carbide Coating: T9215 (CVD) Plate form: rhombic, with cylindrical hole Chipbreaker: double-sided Application: turning (external and internal) Model series: ISO turning inserts FAQ What materials is this insert best suited for? The CNMG 120404-TM T9215 is optimised for medium steel machining; the T9215 CVD coating enhances wear resistance for continuous to lightly interrupted cuts. Can the insert be used for finishing passes? Yes — the 0.4 mm corner radius and the double‑sided chipbreaker facilitate improved surface quality during finishing operations while maintaining adequate edge strength. How does the ISO CNMG120404 designation affect holder selection? ISO CNMG120404 specifies the plate geometry and size; matching holder form, relief angle, tolerance class, fastening and thickness ensures secure clamping and correct cutting geometry. Is the insert suitable for interrupted cuts? The T9215 grade provides good fracture toughness and is suitable for continuous to lightly interrupted cuts; heavy interruption may require a different geometry or a tougher grade. What advantages does the CVD coating offer? The CVD coating improves resistance to flank and crater wear, reducing tool degradation at elevated cutting speeds and supporting longer effective tool life. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.

Data inconsistency detected: the product lists "Sumitomo" as manufacturer, which is not included in the approved manufacturer directory for this specification. Please provide a manufacturer from the approved list (Kennametal, ISCAR, Sandvik, MetavCUT) or confirm the correct manufacturer details so a compliant product description can be generated. It is important to ensure that the manufacturer aligns with the approved directory to maintain compliance with the specification requirements and avoid potential issues during the approval process. If "Sumitomo" is indeed the correct manufacturer, additional documentation or clarification may be required to validate its inclusion in the directory.

Take advantage of the combination of positive 55° geometry, a PVD AC530U coating and high fracture resistance for predictable finishing results in small depths; order the insert directly via Metav Werkzeuge or ask the consultants for process parameters and availability. Sumitomo DCMT11T304N-LU AC530U indexable insert for finishing and light turning — Positive 55° PVD-coated carbide Sumitomo DCMT11T304N-LU AC530U is a positive D‑rhombus insert engineered for fine finishing and light turning of steel and stainless steel in applications with small depths and intermittent cuts Positive 55° D‑rhombus geometry PVD AC530U with high fracture resistance LU fine-chip breaker for stable chips Optimised for small depths and interrupted cuts Consistent finishing with a positive 55° geometry The combination of a positive 55° cutting angle and a fine LU chipbreaker delivers low cutting forces and a controlled chip shape, which is particularly beneficial when machining thin-walled components or parts in unstable setups. The positive rake reduces radial loads, so surface integrity improves during finishing operations. The insert’s corner radius 0.4 mm supports a consistent edge condition for predictable surface finish without aggressive material removal. Coating and substrate designed to resist chipping The multi‑layer PVD Super‑ZX‑Coat (TiAlN/AlCrN) in the AC530U grade combines a hard surface with enhanced toughness; with a measured hardness of 91.4 HRA and a reported bending fracture strength of 3.3 GPa, the system minimises edge breakage in interrupted cuts. This coating-substrate pairing is aimed at delivering high fracture resistance and sharp positive edges that maintain form during light turning and finishing, extending usable edge life under conservative cutting speeds. Geometry and handling for reliable indexation The insert’s D‑rhombus 55° form and neutral cutting direction enable flexible toolholder choices while the cylindrical hole with one-sided countersink ensures secure seating and repeatable positioning in standard toolholders. With two usable cutting edges per insert, a thin plate thickness of 3.97 mm and a relief angle of 7°, the design supports easy re‑indexing and stable clamping — a practical advantage when frequent edge changes are required in small‑batch or mixed‑series production. Process window and practical recommendations For best results start conservatively: depth of cut (ap) in the range 0.2–1.5 mm and feeds between 0.05–0.20 mm/rev, adjusting speeds by material and machine rigidity. The grade is optimised for finishing / light turning of steel and stainless steel and performs well in interrupted cuts and contours; it is not intended for hard roughing, continuous high‑speed heavy cuts, cast iron or non‑ferrous alloys. Packaged in practical units of 10 pieces, the inserts originate from Japan and are suitable where precise surface quality and edge stability are priorities. For supplementary technical data or tailored cutting parameter recommendations, Metav Werkzeuge provides application support via e‑mail and telephone. Contact Metav Werkzeuge for precise process support and availability of the Sumitomo AC530U insert — phone +49 2822 7131930 or e‑mail info@metav-werkzeuge.com Technical data Article number: 203727-Sumitomo Manufacturer item no.: DCMT11T304N-LU AC530U Type: Indexable insert for turning Manufacturer: Sumitomo Origin: Japan Facts Cutting angle: 55° Relief angle: 7° Plate thickness: 3.97 mm Cutting-edge length: 11.6 mm Corner radius: 0.4 mm Inner hole diameter: 9.525 mm Number of cutting edges: 2 Tolerance class: M Hardness: 91.4 HRA Bending fracture strength: 3.3 GPa Special features Geometry: D‑rhombus 55°, positive Chipbreaker: LU – fine-chip, one-sided, positive rake ~15° Coating: PVD Super‑ZX‑Coat TiAlN/AlCrN multi‑layer Material: Cemented carbide, PVD-coated Application: Finishing and light turning of steel and stainless steel Hole style: Cylindrical hole with one-sided countersink Feed/direction: Neutral Pack size: 10 pieces Origin: Japan Edge type: Two usable cutting edges FAQ What machining tasks suit this insert best? This insert is intended for finishing and light turning of steel and stainless steel; it performs well with small depths and interrupted cuts where surface quality and edge stability are required. Which grade and coating does the insert use? The insert is supplied in the AC530U grade with a multi‑layer PVD Super‑ZX‑Coat (TiAlN/AlCrN), offering a balance of hardness and fracture resistance for fine finishing. What are the recommended starting parameters? A practical starting point is ap 0.2–1.5 mm and feed 0.05–0.20 mm/rev; speeds should be adapted to material and machine rigidity, beginning conservatively. How many usable edges does each insert provide? Each insert offers two usable cutting edges, allowing economical re‑indexing during production. Is this insert suitable for cast iron or aluminium? This grade is not optimised for cast iron or non‑ferrous metals; it is designed primarily for steel and stainless steel finishing applications. Manufacturer/Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Benefit from the combination of a positive 55° D‑rhombus geometry, a proven SU chipbreaker and the CVD‑coated AC8035P grade for secure edges and stable performance in light, interrupted steel turning; order the insert directly via Metav Werkzeuge or consult our specialists for application support. DCMT11T304N-SU AC8035P turning indexable insert — positive 55° geometry, CVD-coated (Sumitomo) The Sumitomo DCMT11T304N-SU AC8035P is a positive, D‑rhombus 55° indexable insert designed for light, interrupted steel turning with an SU chipbreaker and a 0.4 mm corner radius CVD-coated grade AC8035P for edge security Positive D‑rhombus 55° geometry for fine turning SU chipbreaker for light interrupted steel cuts Two usable cutting edges; 0.4 mm corner radius Reliable chip control and secure edges for interrupted cuts The positive D‑rhombus 55° profile combined with the SU chipbreaker creates controlled chip breakage and low cutting forces, making the insert particularly suitable for light, interrupted steel machining and components with variable surface conditions such as forged skins. The small 0.4 mm corner radius reduces impact at entry and exit, lowering the risk of chipping; the dual usable cutting edges extend tool life per index, improving uptime and reducing handling frequency. Coating and substrate engineered for reduced crack propagation The insert is produced from CVD‑coated carbide in the AC8035P grade with a surface treatment (ABSOTECH) that reduces stress concentration. With a hardness of 89.4 HRA and a quoted transverse fracture strength of 2.6 GPa, the combination provides high edge and break resistance under interrupted loads. The approximately 9 µm coating thickness optimises edge protection; note that while the grade excels in interrupted and variable conditions, continuous, quiet high‑speed finishing is not its primary strength. Process windows and starting recommendations for steady results For stable cutting start in the suggested geometry range: radial depth of cut ap 0.5–2.5 mm and feed f 0.07–0.30 mm/rev. Recommended cutting speeds are application dependent: Vc ≈ 140–220 m/min for mild steels and ≈ 90–160 m/min for higher alloyed or carburised steels, beginning at the lower end and increasing as process confidence grows. These ranges help achieve repeatable component quality while protecting the insert from overload during entry and broken surfaces. Dimensions, clamping and handling for easy integration Key dimensions and handling details support simple machine integration: plate thickness 3.97 mm, usable cutting edge length 11.6 mm, inner hole diameter 9.525 mm with a cylindrical hole and one‑sided countersink, and two usable cutting edges per insert. The insert is supplied in a pack unit of 10 pieces and is produced in Japan; tolerance class M ensures consistent fit in standard turning toolholders. The neutral cutting direction and positive clearance angle of 7° combine for forgiving tool behaviour under variable conditions. Contact Metav Werkzeuge today for tailored recommendations on Sumitomo AC8035P inserts and to discuss suitable cutting parameters or sample packs — eMail: info@metav-werkzeuge.com, Tel: +49 2822 7131930 Technical Data Article number: 245078-Sumitomo Manufacturer SKU: DCMT11T304N-SU AC8035P Product type: turning indexable insert Origin: Japan Packaging unit: 10 pieces Data Hardness: 89.4 HRA Plate thickness: 3.97 mm Cutting edge length: 11.6 mm Corner radius: 0.4 mm Included angle / nose angle: 55° Relief angle / free angle: 7° Inner hole diameter: 9.525 mm Number of usable cutting edges: 2 Tolerance class: M Special features Material: carbide, CVD‑coated (AC8035P) Chipbreaker geometry: SU — one‑sided, positive rake ≈ 8° Geometry: D‑rhombus 55°, positive insert Hole style: cylindrical hole with one‑sided countersink Application: light, interrupted steel turning; suitable for forged surfaces and variable conditions Coating details: ABSOTECH CVD, layer thickness ≈ 9 µm; reduced surface stresses Mechanical: high edge and fracture resistance; bending strength 2.6 GPa Limits: not optimised for heavy roughing or continuous high‑speed finishing FAQ What material is this insert best suited for? The DCMT11T304N-SU AC8035P insert is optimised for steel machining, particularly light, interrupted cuts and components with forged surfaces; its AC8035P CVD grade gives improved edge security in such conditions. Which chipbreaker is fitted and what does it achieve? The insert features an SU chipbreaker, a one‑sided positive design that provides controlled chip formation and reduced cutting forces during interrupted and variable‑condition turning. What are the recommended cutting parameters to start with? Begin with ap 0.5–2.5 mm and feed 0.07–0.30 mm/rev; suggested cutting speeds are ≈ 140–220 m/min for mild steels and ≈ 90–160 m/min for higher alloyed steels, adjusting upward as stability permits. How many times can the insert be indexed? The insert has two usable cutting edges, enabling one index change; the positive geometry and robust coating help prolong useful life under interrupted loads. Are there limitations to using this grade? Yes — the AC8035P grade and 55° DCMT geometry are not intended for heavy roughing or for continuous, quiet high‑speed finishing where different grades or geometries perform better. Manufacturer/Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Take advantage of a robust CVD coating and a stable 55° negative geometry to achieve consistent finishes and reduced tooling changes in serial turning. Order the Sumitomo insert directly via Metav Werkzeuge or consult our specialists for application-specific recommendations. Sumitomo DNMG150608N-SU AC820P – indexable turning insert, CVD-coated, 55° D‑rhombus The Sumitomo DNMG150608N-SU AC820P is a double‑sided negative 55° indexable insert designed for finishing to light contouring of steel components. CVD-coated AC820P grade with Al₂O₃/TiCN 55° D‑rhombus negative geometry Robust 6.35 mm plate with 4 edges SU chipbreaker for fine finishing Stable finish quality through advanced coating and grade The combination of the AC820P grade with a CVD Super‑FF‑Coat (Al₂O₃/TiCN) delivers a balance of hardness and thermal resistance that supports consistent edge life during finishing operations. With a measured hardness of 90.1 HRA and a coating thickness of approx. 14 µm, this insert maintains cutting performance on a broad range of steels while reducing flank wear. The technical finish of the coating improves resistance to built‑up edge and helps sustain geometric integrity under the moderate cutting speeds recommended for this family. Geometry and chip control for precise contouring The D‑rhombus 55° negative form combined with the SU chipbreaker provides a stable support zone and gentle chip formation suited to fine cuts. The insert offers a 0.8 mm corner radius and four usable cutting edges, on a 6.35 mm plate that increases rigidity at the toolholder interface. A neutral cutting direction and the cylindrical through‑hole aid in repeatable clamping and quick indexing. Typical starting parameters are ap 0.5–2.0 mm, f 0.08–0.30 mm/rev and Vc in the range 190–310 m/min for steel; validate speeds against workpiece stability and machine dynamics. Productivity and shopfloor advantages Using a double‑sided, four‑edge insert reduces tooling expenditure and downtime for replacements in repetitive finishing tasks. The insert’s robust negative plate and standard form factor (1506) simplify tool‑set planning across turning programmes and facilitate predictable setup. The design is optimised for finishing to light machining rather than heavy roughing or highly interrupted cuts, which helps specify the right insert for the job and avoid premature edge failure. Packing in 10 pieces supports stocked supply and quick replenishment. Contact Metav Werkzeuge for supply and machining guidance on the Sumitomo DNMG150608N-SU AC820P insert — email info@metav-werkzeuge.com or call +49 2822 7131930 for application validation and ordering assistance Technical data Article number: 207074 SKU: 207074-Sumitomo Manufacturer SKU: DNMG150608N-SU AC820P Name: Sumitomo DNMG150608N-SU AC820P Wendeschneidplatte Material: Hartmetall, CVD‑coated Origin: Japan Packaging unit: 10 pieces Numbers / Core technical data Cutting angle / Spitzenwinkel: 55° Plate thickness: 6.35 mm Corner radius: 0.8 mm Number of cutting edges: 4 Cutting edge length: 15.5 mm Inner circle / bore: 12.7 mm Hardness: 90.1 HRA Bending strength: 2.2 GPa Coating thickness: approx. 14 µm Recommended depth of cut (ap): 0.5–2.0 mm Recommended feed (f): 0.08–0.30 mm/rev Recommended cutting speed (Vc) for steel: 190–310 m/min Tolerance class: M Designs / Special features D‑rhombus 55° negative plate form SU chipbreaker, double‑sided geometry Four usable cutting edges per insert Neutral cutting direction Cylindrical through‑hole (Zylindrisches Durchgangsloch) CVD Super‑FF‑Coat (Al₂O₃/TiCN) Robust 6.35 mm plate for increased rigidity Intended for finishing to light contouring; not for heavy roughing or heavy interrupted cuts Manufacturer article number: 207074 ANSI reference: DNMG442ESU Monotaro code: 41306045 FAQ What materials is this insert suitable for? The Sumitomo DNMG150608N-SU AC820P insert is aimed at machining steel in finishing to light contouring operations, leveraging its AC820P CVD coating and SU chipbreaker for steady edge behaviour. How many cutting edges are available per insert? Each insert provides four usable cutting edges thanks to its double‑sided negative design, which supports economical tool usage and rapid indexing. Which cutting parameters should be considered as a starting point? Start with ap 0.5–2.0 mm, feed 0.08–0.30 mm/rev and Vc ~190–310 m/min for steel; the actual choice depends on workpiece rigidity, toolholder stability and machine capability when using the Sumitomo AC820P grade. Can this insert be used for roughing operations? No — the insert’s SU chipbreaker is a fine/finish geometry optimised for light cuts; it is not recommended for heavy roughing, very high feeds or severely interrupted cuts. Is the coating suitable for elevated temperatures? The CVD Super‑FF‑Coat (Al₂O₃/TiCN) offers thermal stability and wear resistance beneficial for finishing speeds, helping to reduce flank wear during continuous finishing passes. Manufacturer / Responsible: Sumitomo Electric Hardmetal Corp.; 1‑1‑1 Koyakita, Itami, Hyogo 664‑0016; Japan

Take advantage of the combination of reliable CVD ABSOTECH Platinum coating, a GU universal chipbreaker, and an 80° C-rhombus geometry for consistent performance in general and medium steel turning; order directly via Metav Werkzeuge or consult the technical team for application-specific advice. Sumitomo CNMG120408N-GU AC8025P indexable turning insert — 80° C-rhombus, CVD-coated The Sumitomo CNMG120408N-GU AC8025P is a negative 80° indexable insert designed for general and medium steel turning, providing stable cutting in continuous to lightly interrupted conditions. C-rhombus 80° negative geometry CVD ABSOTECH Platinum coating AC8025P GU universal chipbreaker, double-sided Four usable cutting edges per insert Consistent performance for general and medium steel turning The insert is engineered around an 80° C-rhombus geometry and a GU universal chipbreaker, which together deliver stable engagement and reliable chip control in typical steel turning tasks. The CVD ABSOTECH Platinum coating with a hardness of 90.1 HRA and an approx. 12 µm layer thickness reduces adhesion and build-up at the cutting edge, extending productive cutting intervals. This combination is particularly beneficial where repeatable surface quality and predictable tool life are priorities. Predictable cutting window and machining recommendations Recommended cutting windows are documented to support process planning: for workpieces up to ~180 HB, a depth of cut (ap) of 1.0–4.0 mm, feed 0.20–0.50 mm/rev, and cutting speed Vc 200–320 m/min (optimum ≈ 260 m/min) form a validated starting point. For harder materials above ~180 HB, the same ap and feed ranges apply but with reduced speeds (Vc 130–230 m/min, optimum ≈ 165 m/min). These values enable a straightforward selection of parameters and allow setup engineers to balance productivity and tool life efficiently. Robust edge security and operational versatility The double-sided design provides four usable cutting edges and a 0.8 mm corner radius, offering a broad window for finishing and semi-finishing passes. The insert’s bending strength of 2.3 GPa supports reliable performance under varying cutting forces. While optimised for general steel work, the insert is not the primary choice for heavy interrupted cuts, maximum high-speed continuous cuts, hardened steel or stainless steel — its strengths lie in a wide, economical application range with low adhesion and good resistance to edge chipping. Discuss machining parameter optimisation and order Sumitomo CNMG120408N-GU AC8025P inserts through Metav Werkzeuge; technical consultants are available at info@metav-werkzeuge.com or +49 2822 7131930 to tailor recommendations to specific machines and workpiece materials Technical data Article number: 19P7335 SKU: 230846-Sumitomo Manufacturer SKU: CNMG120408N-GU AC8025P Product: Sumitomo CNMG120408N-GU AC8025P indexable insert Origin: Japan Numbers / Core technical data Hardness: 90.1 HRA Layer thickness: approx. 12 µm Bending strength: 2.3 GPa Plate thickness: 4.76 mm Cutting edge length: 12.9 mm Inner hole diameter: 12.7 mm Corner radius: 0.8 mm Number of usable edges: 4 Pack quantity: 10 pieces Included angle / tip angle: 80° Tolerance class: M Recommended windows (≤ ~180 HB): ap 1.0–4.0 mm; f 0.20–0.50 mm/rev; Vc 200–320 m/min (optimum ≈ 260 m/min) Recommended windows (> ~180 HB): ap 1.0–4.0 mm; f 0.20–0.50 mm/rev; Vc 130–230 m/min (optimum ≈ 165 m/min) Designs / Special features C-rhombus 80° negative geometry GU universal chipbreaker, general/middle machining, double-sided Carbide, CVD-coated (ABSOTECH Platinum) Cylindrical through-hole Neutral cutting direction Four usable edges per insert Current Sumitomo first recommendation for general steel turning Not optimised for highest-speed continuous cuts or heavily interrupted/hardened steel FAQ What materials is this insert intended to machine? The Sumitomo CNMG120408N-GU AC8025P indexable insert is intended primarily for general and medium steel turning and performs best within the documented cutting windows for mild to medium-hard steels. What does the GU chipbreaker deliver in practice? The GU universal chipbreaker on this insert provides controlled chip formation for a wide range of cutting depths and feeds, supporting predictable surface finish and reduced edge build-up during standard turning tasks. How many usable edges are available per insert and what is the corner radius? Each double-sided insert supplies four usable cutting edges and a corner radius of 0.8 mm, allowing for multiple indexings before replacement. Are there any application limits for this grade? The AC8025P grade is not the primary choice for the heaviest interruptions, extreme high-speed continuous cuts or hard and stainless steels; it is optimised for a broad, economical range of steel turning operations. What is the significance of the CVD ABSOTECH Platinum coating? The CVD ABSOTECH Platinum coating enhances surface smoothness and reduces adhesion at the cutting edge, lowering the risk of built-up edge and improving edge security under typical turning conditions. Manufacturer: Sumitomo; Origin: Japan

Take advantage of the large positive geometry and the AC820P CVD coating to achieve low cutting forces and consistent finishing results; combine reliable fracture resistance with two usable cutting edges for efficient production flow. Order the insert directly via Metav Werkzeuge or consult our specialists for application advice. Sumitomo CCMT120408N-SU AC820P indexable turning insert – large positive C‑Rhombus 80°, CVD-coated The Sumitomo CCMT120408N-SU AC820P is a large, positive 80° C‑rhombus insert designed for finishing to light external and internal turning of steel, featuring an SU chipbreaker and a 0.8 mm corner radius for low cutting forces and improved surface quality Large positive C‑rhombus 80° form CVD-coated AC820P, low cutting forces SU chipbreaker optimised for finishing 0.8 mm corner radius, two usable edges Cleaner finishing with lower cutting forces The large positive C‑Rhombus 80° geometry reduces cutting resistance and lowers power draw during light turning operations, which directly benefits cycle times and tool life. The positive rake and the SU chipbreaker produce short, controllable chips suitable for uninterrupted finishing passes, helping to maintain a stable cutting regime. For machining operations where surface quality and dimensional consistency matter, this geometry minimises vibration and supports predictable tool wear, resulting in fewer rework cycles and improved process stability. Durable coating and material for balanced wear resistance The insert is made of CVD-coated cemented carbide with the AC820P specification; the CVD Super‑FF‑Coat (Al₂O₃/TiCN) with a layer thickness of about 14 µm offers a combination of wear resistance and fracture toughness. With a measured hardness of 90.1 HRA and a flexural strength of approximately 2.2 GPa, the grade is engineered for steady performance in finishing and light turning of steel. Recommended cutting data supports efficient operation at Vc 190–310 m/min (optimum 250 m/min) with feeds in the range f 0.07–0.30 mm/U; these parameters help exploit the coating’s strengths while avoiding aggressive conditions for which this grade is not intended. Integration and economy for day-to-day production The insert’s 0.8 mm corner radius and two usable edges provide a practical balance between edge strength and fine finish capability, reducing tool change frequency and inventory complexity. The cylindrical hole with one‑side countersink and the neutral cutting direction support secure mounting in common turning toolholders, while the 4.76 mm plate thickness contributes to stable clamping and repeatable positioning. With recommended depth of cut ap 0.5–2.5 mm and a clear specification window for feeds, the component integrates smoothly into established turning cycles and is supplied in a standard unit of 10 pieces for predictable replenishment. Contact Metav Werkzeuge for application-specific recommendations on the Sumitomo CCMT120408N-SU AC820P insert or to check current availability; phone +49 2822 7131930 or email info@metav-werkzeuge.com Technical data Article number: 207117-Sumitomo Manufacturer SKU: CCMT120408N-SU AC820P Product type: Indexable turning insert Article name: Sumitomo CCMT120408N-SU AC820P Wendeschneidplatte Facts Geometry: C‑Rhombus 80° Cutting angle / tip angle: 80° Clearance angle: 7° Corner radius: 0.8 mm Plate thickness: 4.76 mm Cutting edges: 2 usable edges Cutting length: 12.9 mm Inner circle: 12.7 mm Tolerance class: M Hardness: 90.1 HRA Flexural strength: ~2.2 GPa Recommended ap: 0.5–2.5 mm Recommended feed f: 0.07–0.30 mm/U Cutting speed Vc: 190–310 m/min (optimum 250 m/min) Packaging unit: 10 pieces Special features Material: CVD-coated cemented carbide Coating: CVD Super‑FF‑Coat (Al₂O₃/TiCN), ~14 µm Chipbreaker: SU (single-sided, positive chip geometry) Hole style: Cylindrical hole with one-sided countersink Application: Finishing to light external and internal turning of steel Strengths: Low cutting forces, large positive form, balanced wear and fracture resistance Limits: Not intended for heavy interrupted cuts, aggressive roughing, or primary stainless steel applications Origin: Japan FAQ What materials is this insert suitable for? The CCMT120408N-SU AC820P insert is optimised for finishing and light turning of steel, with the coating and geometry tuned to low cutting forces and stable wear behaviour in those applications. Can this grade be used for heavy interrupted cuts or roughing? No; the AC820P CVD grade and the positive SU geometry are designed for finishing and light machining. Heavy interrupted cuts or aggressive roughing exceed the recommended operating envelope for this insert. What are the recommended cutting parameters for efficient finishing? Recommended ranges are Vc 190–310 m/min (optimum 250 m/min) with feeds f 0.07–0.30 mm/U and depths of cut ap 0.5–2.5 mm, which leverage the coating and geometry for consistent surface quality. How many usable edges does the insert offer and what is the corner radius? The insert provides two usable cutting edges and a corner radius of 0.8 mm, balancing edge strength with the capacity to achieve fine surface finishes. Does the insert require a special toolholder due to the hole style? The cylindrical hole with a one-sided countersink is compatible with common clamping systems for CCMT-style inserts; secure seating and correct tightening in a suitable holder ensure repeatable performance. Manufacturer/Responsible: Sumitomo Electric Hardmetal Corp., 1-1-1, Koyakita, Itami, Hyogo 664-0016 (in Itami Works of Sumitomo Electric Industries, Ltd.)

Take advantage of the CVD-coated T9215 grade for extended tool life and high feed rates to maintain a stable machining process; order the insert directly via Metav Werkzeuge or consult our specialists for application advice. WNMG 080404 T9215 indexable insert (trigon, 80°) — Tungaloy WNMG 080404 T9215 is an indexable trigon insert engineered for medium turning of ISO P15 Stahl, combining a modern CVD surface for high wear resistance with geometry optimised for stable, productive cutting CVD T9215 for high wear resistance Extended tool life at high speeds Trigon insert with 80° cutting geometry Double-sided chipbreaker, cylindrical hole Boosted productivity through advanced CVD technology The new CVD substrate T9215 delivers significantly improved resistance to wear and breakage in medium turning of ISO P15 Stahl, enabling higher cutting speeds and feeds without compromising edge life. Because the coating suppresses crack initiation and limits crack propagation, the cutting edge can remain in service for longer, reducing changeover frequency and increasing uptime. This leads to measurable gains in throughput for batch and continuous production environments while maintaining consistent component quality. Consistent chip control and repeatable surface finish The trigon geometry with an 80° cutting angle and a 0° rake leads to robust cutting mechanics and steady engagement with the workpiece. The integrated double-sided chipbreaker supports reliable chip formation across typical turning parameters for medium machining, while the 0.4 mm nose radius balances edge strength and fine surface finish. The cylindrical hole allows secure clamping, and the 4.76 mm thickness contributes to vibration dampening; together these features support repeatable dimensional accuracy and improved process stability. Practical advantages for workshop productivity and process security Application-focused design choices translate into practical benefits on the shop floor: fewer stoppages for insert changes, stable cutting at higher feeds, and predictable tool behaviour when machining Stahl in the specified ISO class. The insert’s composition and surface technology reduce the risk of premature edge failure, supporting longer tool cycles and simplified tool inventory management. As a result, the solution is well suited to manufacturers pursuing efficient, reliable turning operations without complex process requalification. For tailored recommendations on implementing Tungaloy T9215 grade inserts in existing turning processes, contact Metav Werkzeuge to discuss the SKU M702011230009 and application parameters Technical data Article number: M702011230009 Designation: WNMG080404 Type: WNMG Grade: T9215 Manufacturer: Tungaloy Facts Radius: 0.4 mm Insert size: 08 Thickness: 4.76 mm Cutting angle: 80° Rake angle: 0° Special features Carbide substrate CVD coating T9215 Double-sided chipbreaker Cylindrical hole Trigon shape Negative rake angle 0° For medium turning of ISO P15 (Stahl) FAQ What materials is this insert designed for? The Tungaloy WNMG 080404 T9215 insert is developed primarily for medium turning of ISO P15 class Stahl, offering optimised wear resistance for these materials. How does the T9215 CVD grade improve tool life? The CVD T9215 surface treatment suppresses crack initiation and slows crack growth, which increases the usable life of the cutting edge under higher speeds and feeds. Can the insert be used on both roughing and finishing operations? The combination of an 80° geometry and a 0.4 mm nose radius makes the insert suitable for stable medium turning where a balance between material removal and surface finish is required. Is the insert reversible or indexable? This is a double-sided indexable insert; both faces can be used to extend service life before replacement is necessary. Which SKU corresponds to this insert for ordering? Order reference: M702011230009 for the WNMG 080404 T9215 indexable insert by Tungaloy. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.

Take advantage of the combination of CVD-coated carbide wear resistance, a versatile 0.8 mm corner radius and optimised chip control for a productive turning process; order the inserts via Metav Werkzeuge or consult the technical team for application-specific guidance. WNMG 080408 T9215 — Trigon Turning Insert by Tungaloy (CVD-coated carbide, TM chipbreaker) WNMG080408-TM T9215 is an ISO-standard turning insert designed for medium-steel machining, offering high wear resistance and reliable performance in continuous and light interrupted cuts. CVD-coated carbide grade T9215 Optimised TM chipbreaker design Trigon insert with cylindrical hole 0.8 mm corner radius for versatility ISO 080408 for standardised holders Engineered for consistent productivity in medium-steel turning The insert is manufactured from CVD-coated carbide, grade T9215, which combines extended tool life with improved fracture resistance. This composition is specifically chosen for medium steel applications, where abrasive wear and moderate mechanical shocks occur. The result is a measurable increase in cutting time between changes and fewer unplanned tool exchanges, which supports steady production flow and lowers process costs. The coating process enhances surface hardness and thermal stability, enabling higher cutting speeds while maintaining dimensional control and predictable tool wear. Geometry and clamping that ensure repeatable results The trigon shape with a cylindrical hole and defined ISO dimensions ensures secure clamping in compatible holders; compatibility depends on form, relief, tolerance class, fastening, size and thickness. The insert’s 0° relief angle and an 80° cutting edge angle contribute to a robust cutting geometry that resists chipping under load. The TM chipbreaker is optimised for consistent chip formation in the targeted material range, improving evacuation and reducing the risk of re-cutting. Such stable cutting behaviour supports a better surface finish and reduces the need for secondary operations. Practical selection guidance for reliable machining For turning tasks where a balance of wear resistance and fracture toughness is required, the grade T9215 provides a practical compromise between life and robustness. The 0.8 mm corner radius offers versatility for both general finishing and light roughing, while the trigon form increases edge security in interrupted cuts. Selection of chipbreaker and grade should be matched to workpiece material, cut stability and the intended cutting strategy; when set up correctly, the insert promotes longer tool life, reduced downtime and higher hourly throughput. Operators benefit from fewer tool changes and improved process stability, contributing directly to a lower total cost of machining. For production environments seeking durable, high-productivity inserts, request Tungaloy WNMG080408-TM T9215 from Metav Werkzeuge for availability and application advice via info@metav-werkzeuge.com or phone +49 2822 7131930 Technical Data Article number: 6772400 SKU: 6772400-Tungaloy Manufacturer SKU: TUN6772400 Brand: Tungaloy Model series: ISO turning inserts Name: WNMG080408-TM T9215 Application: Turning Facts Corner radius: 0.8 mm Plate thickness: 4.76 mm Insert size: 08 ISO code: 080408 Cutting edge angle: 80° Relief angle: 0° Hole: cylindrical Special features Material: carbide with CVD coating Grade: T9215 Chipbreaker: TM Shape: trigon Suitable for: medium steel, continuous and light interrupted cuts Compatibility: ISO-standard holders, defined by form, relief, tolerance class, fastening, size and thickness FAQ What material range is this insert intended for? The WNMG080408-TM T9215 insert is intended primarily for medium steel machining and performs well in continuous and light interrupted cutting conditions. What advantages does the T9215 grade offer? Grade T9215 is a CVD-coated carbide formulation that offers good wear resistance combined with fracture toughness, supporting higher productivity and consistent tool life. How does the TM chipbreaker affect machining? The TM chipbreaker on this trigon insert promotes stable chip formation and evacuation in the targeted material range, improving surface finish and reducing recutting. Is the insert compatible with standard ISO holders? Yes, the ISO designation 080408 identifies the insert geometry; compatibility with toolholders is established by matching form, relief, tolerance class, fastening, size and thickness. For which types of turning is the 0.8 mm corner radius suitable? The 0.8 mm corner radius provides versatility across finishing and light roughing tasks, offering a balance between edge strength and achievable surface quality. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.