Precision gauge blocks and plug gauges for reliable dimensional control
Mechanical gauge blocks and plug gauges are essential for tactile verification of threads, bores and gap dimensions, providing fast, unambiguous go/no-go results that enhance process reliability and reduce scrap. Designed for industrial metalworking and toolmaking, these precision tools support incoming inspection and final quality checks by delivering traceable measurements in applications such as thread inspection, bore diameter testing and spacing checks. Manufactured from specially hardened, low-distortion alloys and fine-lapped for minimal measurement uncertainty, the range includes thread plug gauges, precision plug gauges and calibration gauge blocks to ensure long-term repeatability and wear resistance.
11.33mm Gauge Pin 50mm Length Workshop Version, Special Steel - Metav IndustryLine
Combining special steel construction, ±0.002 mm repeatability and a compact 50 mm length, this gauge pin provides reliable end‑measure checks in workshop environments; order via Metav Werkzeuge or consult the specialists if further specification is required. Gauge pin, single — 11.33 mm Ø, 50 mm length (Workshop version) by Metav IndustryLine Gauge pin 11.33 mm, 50 mm length is a compact precision end‑measure gauge intended for workshop testing, alignment and dimensional verification of small components ±0.002 mm accuracy for repeatable checks 11.33 mm diameter suited to fine end‑measure tasks 50 mm overall length for compact component access Workshop version with transport case for safe handling Built for repeatable end‑measure checks The gauge pin is designed for reliable dimensional control where consistent contact geometry is essential. The ±0.002 mm specification denotes the pin’s measured variation under controlled conditions, which translates into tight reproducibility when used for end‑measure inspections or matching plug fits. Constructed from special steel, the pin resists wear typical of workshop use while maintaining its profile, so process deviations are reduced and inspection throughput improves. Compact format that supports practical workshop workflows Classified in the micro range (10–100 mm), this compact test gauge offers the ideal balance between reach and stiffness for small parts and assemblies. The 50 mm length and 11.33 mm diameter enable access to confined bores and ends without compromising handling. Supplied as a workshop version and packed in a transport case, the pin is protected during transit and storage, enabling faster deployment on benches or in jigs and minimising downtime caused by damage or loss. Clear technical fit for quality control tasks A simple, robust geometry makes the gauge pin suitable for repeat verification tasks, end‑measure control and use as a reference in fixtures. The combination of special steel material and narrow tolerance supports frequent tactile checks and mechanical gauging applications. Where routine verification is required, this format reduces measurement uncertainty and streamlines quality assurance steps, allowing teams to keep production flowing with dependable referencing. Contact Metav Werkzeuge today for tailored advice on Metav IndustryLine gauge pins, delivery options from Emmerich and assistance matching the component to specific inspection routines — email info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: M323.B33 GTIN: 4061905067747 Manufacturer: Metav IndustryLine Version: Workshop version Measurements & accuracy Diameter: 11.33 mm Length: 50 mm Weight: 0.10 kg Accuracy: ±0.002 mm Materials & delivery Material: special steel Delivery: transport case for safe transport Intended use: end‑measure checks, workshop testing FAQ What is the primary application of this gauge pin? The gauge pin is intended for end‑measure checks, alignment and dimensional verification of small components in workshop environments. What tolerance can be expected during routine checks? The gauge pin is specified with an accuracy of ±0.002 mm, providing close repeatability for inspection and gauging tasks. Is the gauge pin suitable for confined bores and small parts? Yes; the 11.33 mm diameter and 50 mm length make this gauge pin well suited to confined bores and compact component checks. What material is the pin made from and why is that relevant? Manufactured from special steel, the pin offers wear resistance and stable geometry under typical workshop use, preserving measurement integrity. How is the pin delivered to protect it during transport? The workshop version is supplied in a transport case to protect the pin from damage and contamination during handling and transit. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
11.34mm Gauge Pin Length 50mm Workshop Finish - Metav IndustryLine
Take full advantage of ±0.002 mm repeatability combined with a special steel construction and a compact 50 mm gauge length for consistent bore checks and fixture set‑ups; order directly via Metav Werkzeuge or consult the Metav team for application advice. Gauge pin, single, Ø 11.34 mm, length 50 mm (Metav IndustryLine) The gauge pin, single, Ø 11.34 mm, length 50 mm is a workshop‑grade test pin for fast verification of bore diameters and for use as a reference in jigs, gauges and fixture set‑ups across production and inspection environments. High dimensional accuracy ±0.002 mm Special steel construction for longevity Compact 50 mm length for shallow bores Workshop execution for everyday use Precision that removes doubt Manufactured to a tight tolerance of ±0.002 mm, this test pin delivers measurable repeatability that supports consistent quality control in production and inspection processes. The fine tolerance is presented as a clear technical parameter rather than marketing claim: it enables reliable go/no‑go checks and reduces the need for repeated rework. The Ø 11.34 mm diameter is stated to two decimal places to reflect the pin’s intended role as a dimensional master for small‑bore verification; the numerical accuracy helps planners and quality engineers predict fit and clearance without additional measuring steps. Designed for reliable bore checking and fixture work With a length of 50 mm, the pin is geared towards shallow to medium‑depth bores and is compact enough for use in tight fixture arrangements. The single‑piece construction is immediately usable for plug checks, setting end‑stops or calibrating dial indicators when a fixed reference is required. Where traceable dimensional references are needed on the shop floor, this compact test pin serves as a quick, mechanical baseline that complements optical or digital inspection methods. The clear numeric specification of diameter and length makes it straightforward to document acceptance criteria in inspection plans. Robust finish and workshop readiness Constructed from special steel, the pin is engineered for wear resistance under frequent handling typical of workshop use. The combination of durable material and a practical mass (approx. 0.1 kg) ensures stable handling and helps avoid accidental deformation during routine checks. The workshop execution denotes an item built for everyday operational use rather than delicate laboratory conditions: it is suitable for mounting in fixtures, for comparative checks in incoming inspection or for repetitive verification tasks on the shop floor. Where process reliability is in focus, such mechanical masters simplify daily routines and shorten inspection cycles. For precise bore verification choose the Metav IndustryLine gauge pin and contact Metav Werkzeuge for ordering or technical consultation via info@metav-werkzeuge.com or +49 2822 7131930 Technical Data SKU: M323.B34 GTIN: 4061905067754 Article name: Gauge pin, single, Ø 11.34 mm, length 50 mm Core data Diameter: 11.34 mm Length: 50 mm Tolerance / Accuracy: ±0.002 mm Weight: 0.1 kg Measurement range: 11.34 mm Special features Material: Special steel Execution: Workshop execution Category: Gauge pins FAQ What is the stated accuracy of this gauge pin? The gauge pin is specified with an accuracy of ±0.002 mm and is supplied as a single, fixed‑diameter pin (SKU M323.B34). Which material is used for the pin? The pin is manufactured from special steel, chosen for wear resistance and stable dimensional behaviour in workshop conditions. For which tasks is this pin suited? This pin is intended for bore verification, fixture set‑up and as a dimensional master in inspection routines for shallow to medium‑depth holes. Can this pin be used in jigs and fixtures? Yes; the pin’s compact 50 mm length and robust steel construction make it suitable for integration into jigs, stops and comparative fixtures. Is the diameter stated to production tolerances? The nominal diameter Ø 11.34 mm is given to two decimal places to reflect its use as a reference dimension in quality documentation. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
11.35mm Gauge Pin, Workshop Version, 50mm Length - Metav IndustryLine
Take advantage of the combination of workshop‑grade robustness, tight ±0.002 mm tolerance and compact form for repeatable end‑measure checks; order the pin directly via Metav Werkzeuge or consult the specialists for integration into existing gauge sets. Gauging pin M323.B35 — single pin, 11.35 mm diameter, 50 mm length (Metav IndustryLine) Gauging pin M323.B35 is a precision inspection pin designed for end‑measure verification and alignment tasks in workshop metrology and gauge assemblies. Workshop‑grade execution Diameter 11.35 mm precision Length 50 mm robust pin Tolerance ±0.002 mm accuracy Repeatable end‑measure checks with industrial accuracy The M323.B35 is tailored for precision end‑measure and alignment applications where consistent results matter. With a nominal diameter of 11.35 mm and a verified ±0.002 mm variation, the pin reduces measurement uncertainty during repetitive checking tasks. Its geometry supports secure seating in bores and gauge fixtures, improving positional repeatability and lowering the risk of setup errors in production checks. The compact design keeps handling straightforward while offering the dimensional stability required for frequent use. Designed for daily workshop handling and longevity Manufactured from special steel, the pin is finished to withstand regular mechanical interaction without premature wear. The 50 mm length provides sufficient engagement for most gauge and fixture configurations while remaining easy to manoeuvre on the bench. The workshop‑orientated construction gives a robust feel and dependable contact behaviour during seating and removal. These characteristics translate into fewer rejects caused by measurement variation and a longer service life in demanding environments. Practical delivery and storage for safe transport Supplied in a protective transport case, the pin arrives ready for secure storage and movement between workstations. The case mitigates the risk of incidental damage or contamination during handling, preserving the pin’s surface integrity and dimensional fidelity. For operations that maintain sets of gauges, this packing simplifies organisation and reduces downtime when locating the correct pin for a check or assembly operation. Integration and application advantages in inspection workflows As a single gauging pin, the M323.B35 is suited to end‑measure verification, alignment in jigs and quick interchange in gauge sets where a reliable reference diameter is required. The tight tolerance and solid construction support consistent comparisons against reference gauges and mating parts, helping to accelerate in‑process inspection cycles. Where traceable calibration is required, further verification services can be matched to the set‑up to ensure conformity with internal quality plans. Contact Metav Werkzeuge in Emmerich for tailored advice on specifying the M323.B35 and arranging supply – phone +49 2822 7131930 or email info@metav-werkzeuge.com Technical data Article number: M323.B35 GTIN: 4061905062803 ECLASS: 21170231 Facts Diameter: 11.35 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.1 kg Special features Material: special steel Workshop execution Supplied in protective transport case FAQ What applications is this gauging pin intended for? The M323.B35 gauging pin from Metav IndustryLine is intended for end‑measure verification, alignment in jigs and use as a reference diameter in gauge sets where a precise, repeatable contact is required. How tight is the dimensional tolerance of the pin? The product specification lists a dimensional variation of ±0.002 mm, which supports high repeatability for inspection tasks and fixture alignment. Is the pin delivered ready for workshop use and storage? Yes, the M323.B35 is supplied in a protective transport case to preserve surface condition and simplify storage and transport between workstations. What material is the pin made from and why does that matter? The pin is made from special steel, chosen for wear resistance and stable contact characteristics, which helps maintain dimensional fidelity under regular handling. Does the product data include calibration information? The supplied product data does not state inclusion of a calibration certificate for the M323.B35; calibration requirements should be clarified with Metav Werkzeuge if traceable verification is required Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
11.36mm Gauge Pin Length 50mm Workshop Version, Special Steel ±0.002 - Metav IndustryLine
Take advantage of exact diameter control and workshop‑hardened durability to ensure reproducible end‑measure checks; the combination of a tight tolerance and robust special steel keeps inspection routines efficient and reliable. Order the inspection tool directly via Metav Werkzeuge or consult the technical team for clarification. Gauge pin M323.B36 — Test pin, Ø 11.36 mm, 50 mm length (Metav IndustryLine) The gauge pin M323.B36 is a workshop‑grade test pin designed for end‑measure verification and dimensional checks in metrology applications, with a nominal diameter of 11.36 mm and a working length of 50 mm. Workshop-grade construction Diameter 11.36 mm, length 50 mm Dimensional tolerance ±0.002 mm Special steel for wear resistance Precision where it matters A compact inspection element engineered for small‑part verification, the gauge pin delivers a nominal diameter of 11.36 mm with a verified tolerance of ±0.002 mm, providing the kind of repeatable fit control required in component end‑measure tasks. Classified within the micro range for measuring instruments (max. range 10–100 mm), this format prioritises stiffness and minimal flexure, which reduces measurement variance when comparing mating bores or plug fits. The tight tolerance supports direct decision‑making in incoming inspection and assembly validation. Built for robust workshop use Constructed from special steel, the pin balances surface hardness with corrosion resistance to withstand regular contact during inspection cycles. At a working length of 50 mm and weighing approximately 0.1 kg, the component is easy to handle while remaining sufficiently substantial to avoid accidental bending under normal use. The workshop configuration emphasises longevity and ease of cleaning; the finish supports friction‑controlled insertion and removal, helping maintain measurement reliability over many cycles. The M323.B36 is thus suitable for daily use at machine benches and quality stations. Integrating the pin into quality workflows The pin serves as a straightforward gauge for go/no‑go checks, reference fits and end‑measurement verification within established inspection routines. When combined with calibrated fixtures or comparator setups, the low declared variation enables clearer pass/fail criteria and reduces rework. Supply from a dedicated precision partner ensures traceability and consistent availability, supporting planned inspection intervals and tooling schedules. The product’s concise specification simplifies documentation and procurement for quality management systems. Contact Metav Werkzeuge for tailored advice on incorporating the M323.B36 into inspection protocols or to request delivery from the Emmerich inventory; technical queries are welcomed at info@metav-werkzeuge.com or by phone on +49 2822 7131930 Technical Data Article number: M323.B36 GTIN: 4061905063220 Manufacturer: Metav IndustryLine Facts Diameter: 11.36 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.1 kg Special features Material: special steel Workshop execution Category: gauge pin / test pin Accuracy class: industrial inspection FAQ What is the declared tolerance of this gauge pin? The declared dimensional tolerance for the M323.B36 gauge pin is ±0.002 mm, suitable for fine workshop inspection tasks. Is the M323.B36 suitable for routine end‑measure checks? Yes; the Metav IndustryLine M323.B36 is designed for end‑measure verification and fits direct inspection workflows for small bores and mating parts. What material is the pin made from and why does that matter? The pin is made from special steel, chosen for wear resistance and stability so that dimensional properties remain consistent through repeated use. Which measuring category does this pin belong to? With a nominal diameter of 11.36 mm it falls into the micro category (measuring range up to 100 mm), where stiffness and minimal flexure are priorities for precision. Can this pin be used as a reference in fixture testing? The M323.B36 is suitable as a reference element in fixture and comparator tests thanks to its tight tolerance and stable material properties. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
11.37mm Gauge Pin 50mm Length Workshop Version, Special Steel - Metav IndustryLine
Benefit from workshop-grade robustness combined with sub-millimetre repeatability: the compact 11.37 mm diameter and a measured tolerance of ±0.002 mm ensure consistent end-dimension checks for small components; order directly via Metav Werkzeuge or consult our advisors for application-specific guidance. Gauge pin M323.B37 — single test pin, Ø 11.37 mm, length 50 mm (Metav IndustryLine) The Gauge pin M323.B37 is a single test pin designed for precise end‑dimension verification and fit checks in compact assemblies and precision components. Workshop-grade execution Diameter 11.37 mm exact Tolerance ±0.002 mm Length 50 mm special steel Reduce rejects with measurable precision A tight tolerance of ±0.002 mm provides a markedly lower measurement uncertainty than common workshop pins, translating directly into fewer fit‑related rework cycles. The controlled diameter of 11.37 mm reduces variation when checking mating bores and seating surfaces; this repeatability is especially beneficial where small accumulations of clearance determine assembly success. By specifying a single, verified diameter, inspection sequences become faster and more reliable, supporting lean quality routines and consistent production throughput. Compact format for fine‑part inspection With an overall length of 50 mm, the pin is tailored to compact inspection tasks where reach and rigidity must be balanced. The dimensions place the item in the micro class for calipers and gauge pins, making it ideal for fine mechanical parts, miniature housings and precision fastener seats. The short, stiff geometry minimises bending and eccentricity during contact checks, so measuring setups for small components remain simple and repeatable without specialised fixturing. Durable material built for workshop use Manufactured from special steel, the component combines surface hardness and wear resistance with the dimensional stability required in routine inspection. The workshop‑grade execution resists abrasion from repeated probing and offers longevity under standard shop conditions. Where frequent interchange between gauges and test fixtures occurs, a robust substrate reduces the need for premature replacement and maintains traceability of measurement results over longer intervals. Integration into inspection workflows The single‑piece design supports straightforward handling and storage in gauge racks or inspection trays. Its nominal diameter and tolerance make it straightforward to include in process control plans as a quick go/no‑go reference or as a datum for comparative checks. Compatibility with existing plug‑gauge holders and bench fixtures means the pin can be introduced into established inspection chains with minimal adaptation, accelerating validation and operator familiarity. Procurement and inventory advantages Standardised dimensions and a clear article identity simplify purchasing and stockkeeping. The compact form factor minimises storage footprint while the stable material composition limits drift over time, reducing calibration frequency compared with softer test artefacts. For buyers seeking dependable small‑part inspection aids, this configuration offers a low‑effort route to reproducible checks and predictable tool life. Contact Metav Werkzeuge today for application advice or to confirm compatibility with existing inspection setups — phone +49 2822 7131930 or e‑mail info@metav-werkzeuge.com to discuss the Metav IndustryLine gauge pin and related metrology items Technical Data Article number: M323.B37 GTIN: 4061905063237 Brand: Metav IndustryLine Numbers Diameter: 11.37 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.1 kg Special features Workshop-grade execution Material: Special steel Single test pin FAQ What level of accuracy can be expected from this gauge pin? The Metav IndustryLine gauge pin M323.B37 delivers an accuracy reflected by the specified tolerance of ±0.002 mm, suitable for fine fit and end‑dimension checks. Is this pin suitable for miniature components and watchmaking tasks? Yes; with a diameter of 11.37 mm and compact length, the pin is classified in the micro range and is appropriate for precision inspection of small assemblies. Can the pin be used as a datum for comparative inspections? The single‑piece design of the M323.B37 makes it well suited to act as a reference or datum in comparative checks and simple go/no‑go routines. What material is the pin made from and how does that affect service life? Constructed from special steel, the pin combines wear resistance and dimensional stability, reducing replacement frequency under normal workshop use. Is the M323.B37 compatible with common plug‑gauge holders and bench fixtures? Yes; the standard diameter and length enable integration with typical holders and fixtures used in inspection benches and jig assemblies. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
11.38mm Gauge Pin 50mm Length Workshop Version, Special Steel - Metav IndustryLine
Combining workshop-grade construction with tight dimensional control, this single test pin delivers an 11.38 mm diameter and 50 mm length with a confirmed accuracy of ±0.002 mm, supporting reliable end‑dimension checks and fewer production interruptions. Order the test pin directly via Metav Werkzeuge or ask our consultants for application guidance. M323.B38 Test Pin — 11.38 mm Diameter, 50 mm Length A M323.B38 test pin engineered for precise end‑measurement and inspection tasks in workshop metrology. Workshop‑grade execution Diameter 11.38 mm for end‑gage checks Length 50 mm for fixture access Dimensional accuracy ±0.002 mm Keep tolerances within specification with repeatable measurements The probe is designed to provide consistent dimensional control in routine inspection tasks. With a diameter of 11.38 mm and an overall length of 50 mm, the pin fits typical gauge bores and fixture pockets while preserving accessibility in confined assemblies. The stated ±0.002 mm tolerance reflects the component’s suitability for fine verification work, reducing the risk of false rejects and rework. Using a dedicated test pin like this reduces handling variation compared with improvised substitutes and keeps throughput stable on the shop floor. Robust workshop construction for dependable service life Manufactured from special steel, the component is specified for robust day‑to‑day use in industrial environments. The workshop‑grade execution emphasises dimensional stability under repeated contact and positioning operations. The simple geometry of the pin supports straightforward integration into jigs and inspection sets, while the single‑piece design eliminates play that can arise from multi‑part assemblies. This results in fewer setup adjustments and more time spent on productive measurement tasks. Integrates easily into gauges and inspection routines As a standardised inspection element, the pin lends itself to use as a reference in manual gauges, go/no‑go fixtures and check stands. Its form factor helps achieve reproducible seating and alignment, which is particularly valuable when validating end dimensions or verifying mating features during assembly. The component supports process reliability by enabling quick comparative checks, shortening inspection cycles and improving traceability within established quality workflows. Contact Metav Werkzeuge for application advice and availability of the M323.B38 test pin; reach the team at +49 2822 7131930 or info@metav-werkzeuge.com Technical data SKU: M323.B38 GTIN: 4061905063244 Category: Test pins / Messstifte Facts Length: 50 mm Diameter: 11.38 mm Accuracy: ±0.002 mm Weight: 0.1 kg Special features Material: special steel Workshop execution Single test pin FAQ What is the intended use for this test pin? The M323.B38 test pin is intended for end‑dimension checks, fixture validation and repeatable seating in shop‑floor inspection routines. What accuracy can be expected from the pin? The component is specified with an accuracy of ±0.002 mm, suitable for fine verification work in workshop metrology. Can this pin be used in standard gauge blocks and fixtures? Yes, the 11.38 mm diameter and 50 mm length are compatible with common gauge pockets and jigs used for end‑measurement and assembly checks. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
11.39mm Gauge Pin 50mm Length Workshop Finish - Metav IndustryLine
The combination of a precise 11.39 mm diameter, a compact 50 mm working length and a repeatable ±0.002 mm tolerance provides reliable size checks in busy workshops; order the gauge pin directly via Metav Werkzeuge or consult our specialists for application advice. Metav IndustryLine single gauge pin — 11.39 mm dia, 50 mm length A single gauge pin (11.39 mm, 50 mm length) for precise end‑measurement and go/no‑go verification in workshop environments Single gauge pin 11.39 mm diameter High repeatability with ±0.002 mm tolerance Special‑steel construction for wear resistance Supplied in a protective transport case Reliable size verification for daily workshop use The single gauge pin is designed for straightforward dimensional checks where consistent results matter. The 11.39 mm diameter and 50 mm length provide a compact testing tool suited to bench‑level inspection tasks and assembly verification. With a stated ±0.002 mm tolerance, the pin offers high repeatability that supports process stability and reduces rework. For those unfamiliar with gauge terminology: tolerance denotes the maximum permitted deviation from nominal size, so a small tolerance means closer agreement to the stated dimension and fewer measurement surprises. Accurate tolerance control that supports quality routines Accuracy and reproducibility are central to efficient inspection routines. The pin’s ±0.002 mm specification positions it for fine inspection tasks where narrow tolerances are required. In practical terms this enables reliable go/no‑go assessments and quick verification of mating bores or shafts without elaborate fixturing. The special steel construction brings improved wear resistance compared with untreated steels, extending service life under frequent use and maintaining dimensional integrity over many inspection cycles. Robust design and workshop readiness Manufactured as a workshop version, the pin is built to withstand regular handling in production or maintenance areas. The compact geometry keeps handling simple while the material choice gives solid resistance to abrasion in everyday use. The tool is supplied in a protective transport case to guard the calibrated surface during storage and transit — a practical advantage for mobile inspection tasks or when pins are kept together in a toolkit. Lightweight and easy to place, the pin integrates smoothly into labelling and sorting routines on the shop floor. Practical efficiency: integration into inspection workflows A single, precisely made gauge pin speeds up routine checks and supports decision‑making on the production line. Its compact size reduces setup time compared with larger gauges, and repeatable measurements help maintain process documentation and traceability. Where multiple sizes are used, keeping a consistent set of durable pins minimises downtime and simplifies training for operators unfamiliar with more complex metrology equipment. Contact Metav Werkzeuge today to confirm suitability for specific inspection tasks or to reserve the Metav IndustryLine gauge pin; call +49 2822 7131930 or e‑mail info@metav-werkzeuge.com Technical Data Article number: M323.B39 GTIN: 4061905063251 Brand: Metav IndustryLine Facts Diameter: 11.39 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.1 kg Special features Material: special steel Workshop version Supplied in protective transport case (plastic or wooden) FAQ What inspection tasks is this gauge pin best suited for? The Metav IndustryLine single gauge pin is suitable for end‑measurement and go/no‑go checks on bores, shafts and mating parts where a compact, repeatable reference is required. How tight is the dimensional tolerance of the pin? The gauge pin is specified to ±0.002 mm, offering high repeatability for fine inspection tasks and short‑run quality checks. Is the pin suitable for heavy daily use in a production environment? Yes, the workshop version with special steel construction is intended for routine handling and frequent checks in production and maintenance settings. Does the item come with protective packaging? The tool is supplied in a protective transport case to prevent damage during storage and transport, supporting safe handling between workstations. What identifiers are available for ordering and traceability? Order and trace using SKU/Article number M323.B39 and GTIN 4061905063251 for clear traceability. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
11.3mm Test Pin 50mm Length Workshop Version, Special Steel - Metav IndustryLine
Take advantage of the combination of precise ±0.002 mm tolerance, robust special steel construction and workshop‑ready packaging for dependable end‑measure checks on the shop floor. Order the gauge pin directly via Metav Werkzeuge or consult our specialists for selection and delivery advice. M323.B30 gauge pin, 11.3 mm Ø · 50 mm length (Metav IndustryLine) M323.B30 gauge pin designed for go/no‑go and end‑measure validation in workshop inspection and assembly control. Precision tolerance ±0.002 mm Diameter 11.3 mm, length 50 mm Workshop‑grade special steel Supplied in a transport case Consistent fits for assembly and inspection The M323.B30 is manufactured to a tight ±0.002 mm tolerance, delivering consistently repeatable fits when checking bores, dowels and mating parts. With a nominal diameter of 11.3 mm and an overall 50 mm length, the single‑piece design combines a compact form with the axial stability required for routine end‑measure checks. The use of special steel gives improved wear resistance compared with plain grades, which extends service life under frequent use and reduces the need for early replacement — a direct productivity benefit in production and quality control workflows. Practical handling that speeds up inspection cycles This inspection pin is a lightweight, robust tool that simplifies comparative measurements and assembly verification. The compact mass and straight shank enable quick seating and clear tactile feedback for operators, improving measurement speed without sacrificing accuracy. Supplied in a protective transport case, the instrument is ready for workshop conditions and short transfers between stations. Such practical features contribute to measurable time savings during batch checks and reduce the risk of damage during handling, which supports uninterrupted production. Ready integration into quality routines and inventory The single gauge pin fits directly into established inspection sequences and can be logged in inventory with the SKU M323.B30 and GTIN 4061905066870 for traceable asset management. Its workshop execution is suitable for routine dimensional control and end‑measure validation in machine shops, jigs and fixtures. Where consistent go/no‑go assessment is required, this test pin provides a cost‑efficient, low‑maintenance solution that maintains repeatability across cycles while keeping tooling complexity to a minimum. For reliable end‑measure verification and workshop delivery, request the M323.B30 from Metav Werkzeuge and discuss stock availability or customised packing with our Emmerich team. Technical Data SKU: M323.B30 GTIN: 4061905066870 Brand: Metav IndustryLine Facts Diameter: 11.3 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.1 kg Special features Material: Special steel Workshop‑grade execution Supplied in a transport case Single‑piece gauge pin Application: end‑measure checks FAQ What diameter and length does the gauge pin have? The M323.B30 gauge pin is 11.3 mm in diameter with a 50 mm overall length. What precision can be expected from this inspection pin? The inspection pin is manufactured to a tolerance of ±0.002 mm, suitable for precise end‑measure checks. Which materials is the pin suitable for inspecting? Made from special steel, the pin is intended for dimensional checks of compatible bores and mating parts commonly found in metal and mechanical assemblies. Is the product supplied ready for use in a workshop environment? Yes, the M323.B30 is delivered as a workshop‑grade single pin and comes in a protective transport case for safe handling between stations. How should the gauge pin be stored to retain accuracy? Store the pin dry and protected from impacts in its transport case; regular visual checks for wear will help maintain its measurement performance. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
11.41mm Gauge Pin 50mm Length Workshop Version - Metav IndustryLine
For precise end-measure checks rely on the combination of 11.41 mm diameter, 50 mm length and a tight ±0.002 mm tolerance for consistent workshop measurements; order the test pin directly via Metav Werkzeuge or ask our consultants if needed. Test pin M323.B41 — workshop-grade inspection pin, 11.41 mm Ø, 50 mm length (Metav IndustryLine) Test pin M323.B41 is a single inspection pin designed for end‑measurement and reference tasks in workshop environments, combining a compact form with industrial repeatability. Workshop-grade design Diameter 11.41 mm Length 50 mm Tolerance ±0.002 mm Consistent gauging for repeated end-measure tasks The short, rigid design delivers reproducible contact when used as an end gauge or reference pin in fixtures. With a diameter of 11.41 mm and a measured length of 50 mm, the pin offers predictable seating and minimal lateral play, reducing measurement scatter during repeated checks. The declared ±0.002 mm variation indicates suitability for precise workshop inspection where fine tolerances are required but laboratory conditions are not necessary. Robust material for daily workshop use Made from special steel, this inspection pin tolerates the mechanical demands of everyday handling and fixture insertion. The material choice balances wear resistance with machinability, so the component retains critical dimensions across many cycles. As a single-unit test pin, it integrates easily into Go/No‑Go setups, gauge assemblies or short-run checking fixtures without the need for complex mounting hardware. Practical benefits for production and setup Compact dimensions and a clear dimensional specification translate into practical speed gains during setup and quality checks. The pin’s geometry simplifies alignment in jigs and aids quick verification of end dimensions on components or assemblies. Using a defined reference like this inspection pin reduces setup time and helps maintain production flow by making pass/fail decisions straightforward and rapid. Traceability and workshop suitability Supplied as an individual inspection pin, the component is intended for direct integration into workshop processes; its single‑piece delivery streamlines stocking and replacement. The combination of workshop-grade execution, precise diameter and fine tolerance makes it a dependable choice for machinists, toolmakers and quality technicians who require a compact, repeatable reference for end measurements. For specification advice, sample availability or procurement of this Metav IndustryLine test pin (SKU M323.B41), please contact Metav Werkzeuge in Emmerich for direct support and reliable delivery. Technical data SKU: M323.B41 GTIN: 4061905063275 Manufacturer: Metav IndustryLine Facts Diameter: 11.41 mm Length: 50 mm Weight: 0.1 kg Accuracy: ±0.002 mm eClass: 21170231 Special features Material: Special steel Delivery: single inspection pin Design: workshop execution Application: end measurement / reference gauge FAQ What is the primary use of this inspection pin? The inspection pin M323.B41 from Metav IndustryLine is intended primarily for end‑measurement and reference checks in workshop fixtures and simple gauge applications. Is the tolerance of ±0.002 mm suitable for quality control in production? Yes — the stated ±0.002 mm tolerance makes the M323.B41 appropriate for precise workshop checks and routine production control where sub‑millimetre repeatability is required. Can this pin be used in fixture alignment and Go/No‑Go applications? Yes. The 11.41 mm diameter and 50 mm length provide a compact, repeatable reference that suits fixture alignment and basic Go/No‑Go gauging tasks. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
11.42mm Gauge Pin, Single, 50mm Length, Workshop Finish - Metav IndustryLine
High-precision 11.42 mm gauge pin with a tight ±0.002 mm tolerance and a compact 50 mm length delivers reliable end‑measure references for routine inspection and assembly checks. The workshop execution and special steel construction ensure consistent dimensional behaviour under regular handling. Order the gauge pin directly via Metav Werkzeuge or ask our consultants if needed. Gauge pin, single (Ø 11.42 mm, L 50 mm) — Workshop version by Metav IndustryLine The Gauge pin, single (Ø 11.42 mm, L 50 mm) is a workshop-grade reference pin for dimensional checks, bore verification and go/no‑go assessments in precision assembly and inspection environments. Workshop-grade precision pin Diameter 11.42 mm, length 50 mm Tolerance ±0.002 mm Made from special steel alloy Precision where it counts A compact reference element designed for exact end‑measure checks, the gauge pin provides a measured diameter of 11.42 mm with a verified tolerance of ±0.002 mm. This level of accuracy reduces ambiguity during acceptance testing and supports reproducible results in small‑part inspection. The numerical tolerance specifies the maximum deviation permitted from the nominal size; keeping this within ±0.002 mm means lower rework rates and clearer go/no‑go decisions in production control. Built for everyday workshop use Designed as a Workshop version, the pin combines a short overall length with stable geometry, making it straightforward to handle in confined jigs and fixtures. The core material is special steel, selected for dimensional stability under routine use. The compact 50 mm length minimises bending moments during manual checking and simplifies insertion into bores or alignment features, which in turn speeds up inspection cycles and reduces operator fatigue. Practical applications and handling advantages Sized within the micro range (10–100 mm), the pin is suited to fine mechanical tasks such as bore verification, alignment checks and end‑measure references in small assemblies. Its form factor supports quick tactile verification as well as integration into inspection fixtures or test benches. For workshops seeking consistent reference standards, the pin acts as a tangible dimensional baseline that streamlines quality workflows and shortens decision loops on manufactured parts. For precise workshop measurement assistance and order handling, contact Metav Werkzeuge — specialists are available at info@metav-werkzeuge.com or by phone on +49 2822 7131930 to advise on integration and supply. Technical data Article number: M323.B42 GTIN: 4061905064173 Manufacturer: Metav IndustryLine Material: Special steel Execution: Workshop version Facts Diameter: 11.42 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.1 kg SKU: M323.B42 Special features Compact format for confined fixtures Suited to bore verification and end‑measure checks Workshop execution for routine handling FAQ What tolerance does the gauge pin offer? The gauge pin, single (Ø 11.42 mm, L 50 mm) (Metav IndustryLine, SKU M323.B42) is specified with a tolerance of ±0.002 mm, suitable for fine inspection tasks. Is this pin suitable for bore verification? Yes. The pin's diameter and compact length make it appropriate for bore verification, alignment checks and quick go/no‑go assessments in small assemblies. What material is used for the pin? This gauge pin is manufactured from special steel, chosen for dimensional stability under regular workshop handling. Is the design intended for daily workshop use? Yes. The workshop execution indicates robustness for routine inspection activities and straightforward handling in fixtures and jigs. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
11.43mm Gauge Pin 50mm Length Workshop Version - Metav IndustryLine
Take advantage of precise dimensional control, robust workshop design and straightforward integration into inspection routines for consistent production checks. The combination of 11.43 mm diameter, a tight tolerance of ±0.002 mm and a 50 mm working length supports dependable go/no‑go and end‑measure tasks. Order the gauge pin directly via Metav Werkzeuge or ask our consultants for application advice. Gauge pin M323.B43 — 11.43 mm diameter, 50 mm length (Metav IndustryLine) The gauge pin M323.B43 is a workshop‑grade precision pin designed for end‑measure inspections and plug‑gauge checks in industrial metrology applications. Workshop‑grade construction Diameter 11.43 mm for end‑measure checks Tolerance ±0.002 mm for reliable fits Delivered in protective transport box Consistent dimensional control for production checks A small inspection tool can determine whether a part is acceptable or requires rework. With a declared tolerance of ±0.002 mm, this gauge pin provides the kind of repeatable accuracy that supports fast, objective decisions at the bench or on the shop floor. The 11.43 mm diameter and 50 mm length are matched to common end‑measure and plug‑fit tasks, enabling rapid verification of holes, bores and mating features without the need for complex set‑ups. The tight tolerance reduces uncertainty in pass/fail checks and lowers the risk of downstream assembly issues. Built for the workshop — durable material and handling Constructed in special steel and supplied in a workshop configuration, the pin tolerates routine handling while maintaining surface integrity and dimensional stability. Hardwearing material properties ensure consistent contact behaviour during repeated measurements, and the compact 50 mm length supports easy manipulation in confined spaces. The practical weight of 0.1 kg offers a tangible feel without being cumbersome, so the pin can be used comfortably across multiple inspection stations. Easy integration into existing inspection workflows Designed as a standard gauge‑pin element, this component pairs with plug gauges, gauge blocks and basic go/no‑go fixtures. It functions as a quick reference for end‑measure validation and tactile fit assessments, making it suitable for incoming inspection, in‑process checks and final quality gates. The clear, single‑diameter geometry simplifies comparison tasks and speeds up throughput in repetitive inspection cycles. A reliable partner from a recognised metrology supplier Metav IndustryLine delivers this gauge pin as part of a broader commitment to accessible precision. The product’s shop‑oriented design and consistent manufacturing tolerances reflect Metav’s focus on dependable supply and practical usability. For workshops seeking to standardise simple dimensional checks without overcomplex instrumentation, this pin represents a pragmatic balance of accuracy, robustness and day‑to‑day convenience. Contact Metav Werkzeuge today for tailored application advice or to reserve the M323.B43 for workshop inspection tasks — call +49 2822 7131930 or email info@metav-werkzeuge.com Technical data Article number: M323.B43 GTIN: 4061905064180 ECLASS: 21170231 Facts Diameter: 11.43 mm Length: 50 mm Weight: 0.1 kg Tolerance: ±0.002 mm Special features Workshop version Material: special steel Protective transport box Category: Gauge pin FAQ What nominal diameter does the pin have? The pin has a nominal diameter of 11.43 mm, specified for precise end‑measure and plug‑fit checks with the M323.B43 gauge pin from Metav IndustryLine. What tolerance can be expected from this gauge pin? Dimensional tolerance is ±0.002 mm, which supports repeatable go/no‑go decisions and reliable fit assessments when using the M323.B43 gauge pin. Is the pin suitable for regular workshop use? Yes — the M323.B43 is a workshop‑grade pin made of special steel, designed for routine inspection tasks and handling in industrial environments. How does the gauge pin integrate with other inspection tools? The pin works as a reference element alongside plug gauges, gauge blocks and simple fixtures; the straight geometry makes it easy to use in standard verification workflows. Which product identifier should be quoted when ordering? Please quote the SKU/article number M323.B43 and the GTIN 4061905064180 when enquiring or ordering this gauge pin. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
11.44mm Gauge Pin Length 50mm Workshop Finish - Metav IndustryLine
Take advantage of precise end‑dimension control with a 11.44 mm diameter test pin and 50 mm usable length, delivered as a single, workshop‑grade gauge pin. The combination of special steel construction and a verified positional tolerance of ±0.002 mm supports repeatable inspection and fixture checks. Order or request further specification details from Metav Werkzeuge for seamless procurement and application advice. Gauge pin, single, 11.44 mm, length 50 mm — workshop‑grade (Metav IndustryLine) The Gauge pin, single, 11.44 mm, length 50 mm is a workshop‑grade precision test pin for end‑dimension checks, fixture alignment and pass/fail verification in production and inspection environments Workshop‑grade construction for daily use Diameter specified as 11.44 mm for exact fits Length 50 mm suited to end‑dimension checks Positional tolerance ±0.002 mm for repeatable results Repeatable end‑dimension control for production Engineered for routine inspection work, this test pin provides a 11.44 mm reference diameter with a positional tolerance of ±0.002 mm, ensuring consistent pass/fail decisions during batch checks. The tight tolerance minimises measurement uncertainty and reduces rework by providing a reliable mechanical reference for bores, jigs and assembly fixtures. Where numerical gauging is impractical, a hardened reference pin offers a straightforward, low‑complexity solution for dimensional verification in series production. Robust construction that endures workshop conditions Manufactured from special steel, the pin combines wear resistance with stable geometry across repeated insertions, supporting sustained accuracy over long runs. The 50 mm length gives sufficient engagement for end‑dimension verification while remaining compact for easy handling and storage. The workshop version is tailored to frequent use and simple maintenance, so wear patterns are predictable and replacement scheduling can be integrated into standard quality routines without interrupting production flow. Traceability and shop‑floor integration Delivered as a single item with the SKU M323.B44 and GTIN 4061905064197, the pin is straightforward to catalogue and control within existing quality systems. The simple form factor makes it compatible with manual go/no‑go checks, fixture set‑ups and quick functional inspections. Metav IndustryLine supplies an industrial‑grade reference that balances accessibility and precision, backed by a broad product range that reduces the need for multiple suppliers and keeps procurement practical for small and large shops alike. Contact Metav Werkzeuge for a quotation or technical clarification — Metav IndustryLine specialists can advise on suitability for specific inspection tasks and order processing at info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: M323.B44 GTIN: 4061905064197 Brand: Metav IndustryLine Type: Gauge pin, single Data Diameter: 11.44 mm Length: 50 mm Positional tolerance: ±0.002 mm Weight: 0.1 kg Special features Workshop version Material: special steel Delivered as single item FAQ What materials is the gauge pin made from? The gauge pin is produced from special steel, chosen for durability and stable geometry under repetitive use. What accuracy can be expected from the test pin? The pin provides a positional tolerance of ±0.002 mm, making it suitable for precise end‑dimension checks. Is the M323.B44 suitable for fixture alignment? Yes, the M323.B44 gauge pin is designed for fixture alignment and end‑dimension verification in workshop and production settings. How is the item identified for stock and traceability? Identification is via SKU M323.B44 and GTIN 4061905064197 for straightforward integration into inventory and quality systems. Can the pin be used for go/no‑go checks on small bores? The pin's 11.44 mm diameter and workshop specification make it appropriate as a reference for pass/fail checks on compatible bores Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
11.46mm Gauge Pin 50mm Length Workshop Version, Special Steel - Metav IndustryLine
Reliable dimensional checks are ensured by combining a tight ±0.002 mm tolerance with a compact 50 mm gauge length and robust special steel construction; this delivers consistent end‑measurement verification on the shop floor. Order the gauge pin directly via Metav Werkzeuge or consult our specialists for application advice. M323.B46 gauge pin – 11.46 mm diameter, 50 mm length (Metav IndustryLine) The M323.B46 gauge pin is a precision inspection pin designed for end‑measurement verification and bore checking in workshop and inspection environments Workshop execution for everyday use Diameter 11.46 mm with ±0.002 mm tolerance Compact 50 mm length for easy handling Supplied in protective case Repeatable, measurable precision for in‑line inspection A gauge pin is a fundamental reference tool for quick dimensional checks and the M323.B46 provides repeatable results thanks to its declared ±0.002 mm accuracy. The nominal 11.46 mm diameter and defined length establish a reliable datum for verifying bore sizes, plug fits and end‑masses where exact seating is required. In practical terms, this level of precision supports tighter process control and reduces the need for secondary verification, enabling faster decision making in routine quality checks. Robust workshop design that withstands daily handling Built in a workshop execution, the inspection pin combines a compact 50 mm length with special steel that resists wear in frequent use. The compact form factor keeps handling simple and limits leverage during insertion, reducing the risk of deformation while providing good tactile feedback for manual checks. Delivery in a protective case ensures the gauge surface remains free from knocks and contamination during storage and transport, maintaining measurement integrity and extending service life. Easy integration into inspection routines and traceability The single‑piece design simplifies incorporation into existing inspection procedures and makes the pin a practical tool for fast go/no‑go assessments. Identifiers such as SKU M323.B46 and GTIN support inventory control and traceability in procurement and quality systems. As a workshop‑grade measurement aid, the pin complements fixed gauges and handheld instruments, helping to streamline quality workflows and preserve calibration cycles by reducing unnecessary wear on more complex devices. For reliable end‑measurement checks, order the M323.B46 gauge pin from Metav Werkzeuge or contact our specialists at info@metav-werkzeuge.com / +49 2822 7131930 for tailored advice and delivery options Technical Data SKU: M323.B46 GTIN: 4061905064609 Material: Special steel Type: Gauge pin (single) Dimensions & Tolerances Diameter: 11.46 mm Length: 50 mm Tolerance / Accuracy: ±0.002 mm Weight: 0.1 kg Features & Delivery Workshop execution Supplied in protective case Category: Gauge pins (Messstifte) Article class: 21170231 FAQ What tolerance does the gauge pin offer? The gauge pin M323.B46 is specified with an accuracy of ±0.002 mm, suitable for precise workshop inspections. Is the pin delivered calibrated? The M323.B46 inspection pin is supplied ready for use; no ISO 17025 calibration certificate is included unless specified separately. What applications suit this gauge pin? Typical uses include bore verification, plug checks and end‑measurement references in machining and assembly operations where an 11.46 mm nominal diameter is required. How is the pin supplied to protect the measuring surfaces? The pin is supplied in a protective case to prevent knocks and contamination during storage and transport. Can this pin be used as a reference in quality documentation? Yes, SKU M323.B46 and the GTIN number facilitate traceability and inventory management when referenced in quality records. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
11.47mm Gauge Pin, Single, 50mm Length, Workshop Finish - Metav IndustryLine
Take advantage of the combination of exacting ±0.002 mm tolerance, a ground diameter of 11.47 mm and a compact 50 mm length for reliable end-measurements in busy inspection benches. Order the test pin directly via Metav Werkzeuge or ask our consultants if needed. Test pin M323.B47 — gage pin, Ø 11.47 mm, 50 mm length (Metav IndustryLine) A test pin M323.B47 designed for precise end-measurements and routine go/no-go checks in workshop inspection and small-part assembly. Workshop version for robust daily use Diameter 11.47 mm, ground to tolerance Length 50 mm for end-measurements Special steel for wear resistance Inspection tolerance ±0.002 mm Precision where repeatability matters The M323.B47 is manufactured to a close inspection tolerance of ±0.002 mm, making it a dependable reference on measuring benches and during final acceptance checks. Such a narrow deviation ensures that the pin can be used where reproducible results are mandatory, for example when verifying bore diameters or confirming mating fits. The diameter 11.47 mm is ground to size and referenced to national traceability practices, which reduces uncertainty in pass/fail decisions and supports consistent quality control across production batches. Built for workshop conditions and frequent handling Constructed from special steel and offered in a workshop version, this gage pin balances hardness and toughness for everyday use. The 50 mm length provides enough engagement for end-measurements while remaining compact for handheld or fixture-mounted checks; the item’s modest mass (about 0.1 kg) keeps handling comfortable and positioning precise. A hardened, ground surface reduces wear and protects the critical measuring diameter, extending service intervals and lowering total inspection cost per part. Integrates smoothly into inspection workflows Traceability and identification are straightforward: the article is stocked as SKU M323.B47 with GTIN 4061905064616 for inventory and procurement processes. The pin is ideal for end-measurements and final dimensional verification in assembly, toolmaking and batch testing where consistent reference gauges are required. Delivered as a single test pin, the component slots easily into gauge sets or can be used individually at test benches; its precision and robustness support rapid decisions and minimise rework. For supply enquiries or application advice on the M323.B47 test pin, contact Metav Werkzeuge for expert recommendations and reliable delivery from Emmerich. Technical data Article number: M323.B47 GTIN: 4061905064616 Brand: Metav IndustryLine Measurements / Core data Diameter: 11.47 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.1 kg Special features / Materials Material: special steel Design: workshop version Category: gage pin / test pin FAQ What applications suit this test pin best? The M323.B47 test pin from Metav IndustryLine is intended for end-measurements, bore checking and go/no-go verification in workshop inspection and small-part assembly. Is the diameter guaranteed within stated limits? Yes. The M323.B47 is delivered with the specified diameter of 11.47 mm and a tolerance of ±0.002 mm, suitable for repeatable inspection tasks. Can this pin be used in gauge sets or fixtures? The pin’s compact 50 mm length and robust workshop design make it suitable for integration into gauge sets or fixed inspection fixtures for routine checks. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
11.48mm Test Pin, Single, 50mm Length, Workshop Version - Metav IndustryLine
Take advantage of the combination of pinpoint accuracy, compact dimensions and robust workshop design for reliable end‑measurements and efficient inspection workflows. Order the component directly via Metav Werkzeuge or ask the technical consultants for application advice. Pin gauge M323.B48 — 11.48 mm diameter, 50 mm length (Metav IndustryLine) A Pin gauge M323.B48 engineered for precise end‑measurements and go/no‑go checks in workshop inspection and final control Workshop-grade construction Diameter 11.48 mm, length 50 mm High tolerance ±0.002 mm Special steel material Precision tailored for fine inspection and repeatable checks The pin gauge specified here provides a compact measuring element with a diameter of 11.48 mm and a length of 50 mm, designed for repeatable end‑measurements and reference checks. With a stated tolerance of ±0.002 mm, this inspection pin sits in the high‑precision segment for small gauges and is suitable where dimensional certainty is essential. The component is classified within the micro range (measuring spans up to 100 mm), which makes it especially useful for fine mechanical tasks, end‑dimension verification and tight tolerance acceptance tests in small assemblies. Robust construction that supports workshop throughput Produced from special steel, the item is configured as a workshop version intended for regular handling and use in production environments. The compact geometry reduces bending and handling error while the chosen material offers the wear resistance required for repeated insertion and withdrawal cycles. As a consequence, the gauge supports efficient quality control routines: inspection steps remain fast, reproducible and easy to incorporate into an operator’s standard sequence, reducing rework rates and increasing throughput without sacrificing accuracy. Practical benefits for inspection routines and fixtures Integration into fixtures and go/no‑go jigs is straightforward thanks to the standardised diameter and the moderate length of 50 mm, which balances accessibility with rigidity. The gauge is supplied as a single item and functions well as a reference pin in comparative set‑ups, alignment tasks or manual gauging stations. Documentation such as GTIN and SKU support traceability and inventory control, while the compact format simplifies storage and reduces the time needed to identify the correct gauge during inspection cycles. Request a technical quote or application sample for the Metav IndustryLine pin gauge directly from Metav Werkzeuge in Emmerich to ensure immediate compatibility with existing inspection procedures Technical data Article number: M323.B48 GTIN: 4061905064623 SKU: M323.B48 Label: Prüfstift, einzeln, 11,48 mm Länge 50 mm Facts Diameter: 11.48 mm Length: 50 mm Tolerance / accuracy: ±0.002 mm Weight: 0.1 kg Material: Special steel Special features Workshop design Single piece delivery Micro‑range gauge (suitable for fine mechanical inspection) Compact geometry for reduced bending FAQ What applications suit this pin gauge best? This pin gauge M323.B48 is suited to end‑dimension checks, go/no‑go verification and alignment tasks in small assemblies and fine mechanical components. What level of accuracy can be expected from the gauge? The inspection pin offers a tolerance of ±0.002 mm, providing high precision for tight acceptance criteria in workshop and inspection environments. What material is the pin made from and how does that affect use? Constructed from special steel, the pin combines wear resistance with dimensional stability, supporting repeated usage in production checks. Is this gauge delivered as a single piece or in sets? The product is supplied as a single gauge pin (single piece delivery), making it suitable for replacement, spare stock or selective auditing tasks. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
11.49mm Gauge Pin, Single, 50mm Length, Workshop Version, Special Steel, Supplied in Case - Metav IndustryLine
The combination of 11.49 mm nominal diameter, ±0.002 mm accuracy and a robust 50 mm special-steel shaft ensures repeatable hole checks and reliable end-measurements in workshop environments; the item is supplied in a protective transport box for secure handling. Order supply or request technical advice directly via Metav Werkzeuge for smooth integration into inspection routines. Gauge pin M323.B49 — single precision test pin, 11.49 mm, 50 mm length (Metav IndustryLine) The Gauge pin M323.B49 is a single precision test pin designed for quick diameter verification and end-measurements in workshop metrology, particularly where compact, high-repeatability checks are required. Precision diameter 11.49 mm ±0.002 mm 50 mm hardened special steel shaft Workshop execution for robust use Delivered in protective transport box Repeatable measurements with micro-range precision This measuring pin is engineered for reliable repeatability: the 11.49 mm nominal diameter and the declared ±0.002 mm tolerance give a tight inspection window that reduces uncertainty during pass/fail checks. In practice, this level of accuracy supports fine workshop quality control where small deviations may lead to rework. Classified in the micro measurement range, the pin is optimised for compact components and small bores—an ideal choice for precision fixtures, gauge sets and end‑measurements where operator consistency is crucial. The result is fewer false rejects and more predictable throughput. Durable design that suits everyday workshop use Constructed from special steel and specified as a workshop execution, the pin balances wear resistance and handling robustness. The 50 mm shaft length provides sufficient engagement for many standard checks while keeping the tool compact and easy to position in confined setups. Supplied in a protective transport box, the pin arrives ready for safe storage and transport, reducing the risk of damage between uses. The modest weight supports quick manual handling and rapid set‑up during serial checks without compromising stability under light clamping. Practical integration and measurable benefits for inspection workflows Incorporating this gauge pin into measurement cycles streamlines routine inspections: fixed-diameter pins are simple to use for go/no‑go-style verifications and quick comparative checks against calibrated references. Traceability is supported through the SKU and GTIN labelling, enabling consistent inventory management for tool spares and inspection kits. Used alongside established gauge blocks and master pins, the device shortens inspection times and contributes to predictable quality outcomes—benefits that compound across production runs and reduce downstream corrective actions. For workshop-grade precision choose the Metav IndustryLine gauge pin M323.B49—contact Metav Werkzeuge in Emmerich for supply and application advice at info@metav-werkzeuge.com or +49 2822 7131930 Technical data SKU: M323.B49 Article designation: Single gauge pin, 11.49 mm, length 50 mm GTIN: 4061905065200 Manufacturer: Metav IndustryLine Facts Diameter: 11.49 mm Length: 50 mm Accuracy: ±0.002 mm Weight: 0.1 kg Special features Material: Special steel Version: Workshop execution Delivered in transport box FAQ What applications is this gauge pin suited for? The M323.B49 gauge pin from Metav IndustryLine is intended for quick diameter verification and end-measurements in workshop environments, particularly for compact bores and small precision components. What does the stated accuracy ±0.002 mm mean in practice? An accuracy of ±0.002 mm indicates the declared maximum deviation for the measuring diameter of the M323.B49; it supports tight tolerance checks and repeatable inspection decisions in routine quality control. Is the pin suitable for use with gauge sets and master plugs? Yes, the design of the M323.B49 allows integration with existing gauge sets and master plugs for comparative checks and visual pass/fail procedures. How should the pin be stored to maintain accuracy? The gauge pin is delivered in a protective transport box; storing it in that box and avoiding corrosive environments preserves the surface and measurement integrity. Can this pin be used for through‑hole and end‑face checks? The measuring geometry and 50 mm length make the M323.B49 appropriate for both short through‑hole verifications and end‑face engagement where a fixed reference diameter is required. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
11.4mm Test Pin 50mm Length Workshop Version, Special Steel in Case - Metav IndustryLine
Take advantage of the combination of ±0.002 mm repeatability, a compact 11.4 mm diameter and a 50 mm length in a robust workshop format to secure reliable end‑size checks; order directly via Metav Werkzeuge or consult the Metav specialists for application advice. Gauge pin, single – 11.4 mm Ø, 50 mm length (Metav IndustryLine) The gauge pin, single 11.4 mm, 50 mm length is a hardened reference pin designed for workshop end‑size verification and dimensional control in machining and inspection stations. Workshop version for robust use Tolerance ±0.002 mm for traceable checks 11.4 mm diameter, 50 mm overall length Supplied in protective transport case Precision for repeatable end‑size control The hardened gauge pin delivers a tight tolerance of ±0.002 mm, which supports repeatable pass/fail assessments and reduces ambiguity in size verification. This level of accuracy is suited to comparator checks, plug‑gauge routines and manual inspection tasks where a clear numerical limit is required. By specifying the measurement deviation, the component acts as a stable dimensional reference and helps to reduce non‑conformance risk on the shop floor. Compact form factor with practical reach A diameter of 11.4 mm combined with an overall length of 50 mm provides sufficient reach for recessed features while remaining easy to handle. The shortened profile minimises cantilevering and deflection during insertion, improving the repeatability of measurements in confined bores or stepped components. In workshop contexts, the balance of stiffness and reach makes this size effective for routine checks without complicating handling. Durable material for everyday workshop use Constructed from special steel, the pin is optimised for wear resistance and dimensional stability under frequent use. The material choice supports longevity in abrasive or oily environments common to machining and assembly areas. Corrosion protection and appropriate surface finish contribute to consistent contact conditions, so measurement deviations are driven by the part under test rather than by the gauge itself. Practical delivery and handling The product is supplied in a protective transport case, ensuring safe storage between uses and simplifying organised tool racks in inspection bays. Case delivery reduces the chance of damage from knocks or contamination and streamlines inventory management for quality technicians who maintain multiple reference pins across different sizes. Designed for integration into inspection workflows As a single‑piece reference, the pin is suitable for manual checks, fixture validation and as a reference element within jigs. The straightforward geometry removes ambiguity when documenting routine checks and integrates easily into inspection protocols and production quality records. The compact design also supports efficient storage alongside other metrology tools. Where this pin adds measurable value Use this workshop‑grade gauge pin for end‑size verification, assembly checks and follow‑up inspections where a clear, repeatable physical limit is required. Its combination of tight tolerance, compact dimensions and durable special steel construction reduces rework and helps sustain a stable quality output in small to medium batch production. For precise end‑size control and advice on suitable sizes, contact Metav Werkzeuge (Metav IndustryLine) at info@metav-werkzeuge.com or by phone on +49 2822 7131930 to discuss application requirements and stock availability Technical Data Article number: M323.B40 GTIN: 4061905063268 SKU: M323.B40 Label: Gauge pin, single, 11.4 mm, length 50 mm Facts Diameter: 11.4 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.1 kg Special features Material: Special steel Workshop version Supplied in protective transport case FAQ What is the exact tolerance of this gauge pin? The gauge pin is manufactured to a tolerance of ±0.002 mm, enabling tight end‑size comparisons and repeatable shop‑floor checks. Is the pin suitable for recessed bores and stepped features? Yes. With an 11.4 mm diameter and 50 mm overall length, the pin is designed to access recessed features while maintaining stiffness for reliable measurements. How is the gauge pin delivered and stored? The Metav IndustryLine gauge pin is supplied in a protective transport case to prevent damage and to support organised storage between uses. Which material is used and how does it affect durability? The pin is made from special steel, chosen for wear resistance and dimensional stability under frequent workshop use. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
11.51mm Gauge Pin 50mm Length Workshop Version - Metav IndustryLine
Benefit from a workshop-grade inspection tool that pairs compact handling with ±0.002 mm tolerance and robust construction in special steel; this combination supports reliable, repeatable bore checks. Order the gauge pin directly via Metav Werkzeuge or consult our specialists if further clarification is required. Gauge pin M323.B51 — workshop-grade inspection pin, Ø 11.51 mm, 50 mm length (Metav IndustryLine) Gauge pin M323.B51 is a precision inspection pin designed for fast, repeatable verification of bore diameters in workshop environments and small-series production. Workshop-grade construction Tolerance ±0.002 mm Diameter 11.51 mm Length 50 mm Precision that keeps production reliable The gauge pin M323.B51 delivers a consistently tight ±0.002 mm tolerance that reduces uncertainty during quality checks and speeds up inline inspection. Machined from special steel, the pin maintains dimensional stability under frequent use, which means fewer rechecks and faster decision-making on the shop floor. The clear tolerance rating supports traceable acceptance criteria and simplifies pass/fail routines, providing a rational basis for improved throughput and lower scrap rates. Small size, big flexibility for fine parts Classified in the Micro range (measurement range up to 10–100 mm), this inspection pin is tailored to fine mechanical tasks where space and access are limited. With a diameter of 11.51 mm and a shank length of 50 mm, the format is ideal for checking small bores, assembly fits and end dimensions in precision components. The compact geometry makes handling straightforward for single-handed checks and reduces the risk of bending or misalignment that can occur with longer gauges. Robust workshop design and transport-ready delivery Engineered as a workshop-grade execution, the pin resists routine wear while remaining easy to clean and store. Delivery in a protective plastic or wooden case safeguards the gauge during transport and on-site handling, keeping the measurement surface intact until use. This practical approach to packaging supports reliable measurement results and a longer service life, aligning with Metav’s commitment to make precision accessible and dependable for every workshop. Contact Metav Werkzeuge today to discuss how the Metav IndustryLine gauge pin M323.B51 can be integrated into existing inspection routines or to request bespoke batch inspection advice from our Emmerich team. Technical data SKU: M323.B51 GTIN: 4061905065224 Manufacturer: Metav IndustryLine Facts Diameter: 11.51 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.1 kg Special features Material: special steel Workshop execution Supplied individually in a protective plastic or wooden case Intended use: bore and end-dimension inspection FAQ What tolerances can be expected from this inspection pin? The inspection pin M323.B51 is specified to a tolerance of ±0.002 mm, providing fine-resolution verification for precision bores and fits. Is the gauge suitable for small-series production checks? Yes, the workshop-grade design and compact 50 mm length make this gauge pin suitable for repeatable in-process and final checks in small-series production. What material is the inspection pin made from? The pin is manufactured from special steel, chosen for dimensional stability and wear resistance under regular workshop use. How is the gauge delivered and protected in transit? The gauge pin M323.B51 is supplied individually in a protective plastic or wooden case to ensure the measurement surfaces remain undamaged during transport and storage. Can this pin be used for internal and stepped measurements? The pin is intended primarily for bore and end-dimension inspection; its geometry supports precise verification of internal diameters and end dimensions. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
11.52mm Gauge Pin 50mm Length Workshop Version - Metav IndustryLine
Take advantage of the combination of ±0.002 mm tolerance and special steel workshop construction for reliable fit checks and repeatable end‑measure verification; order directly via Metav Werkzeuge or contact our consultants for application advice. Gauge pin M323.B52 — single test pin, 11.52 mm diameter, 50 mm length (Metav IndustryLine) A gauge pin M323.B52 designed for precise plug‑fit checks and end‑measure verification in workshop environments, supplied in a protective case for safe transport Workshop execution Diameter 11.52 mm, tolerance ±0.002 Length 50 mm solid steel Delivered in protective case Repeatable, measurement‑grade fit verification The cylindrical test pin is intended for quick and reliable plug‑fit and bore verification in production and maintenance settings. With a diameter of 11.52 mm and a declared tolerance of ±0.002 mm, this pin provides high repeatability for go/no‑go fit checks and alignment tasks. Manufactured for workshop use, the geometry is optimised to reduce wobble during insertion so that each check yields consistent comparative results rather than a dimensional report. Robust construction for industrial handling Built from special steel and finished for durable workshop service, the pin sustains repeated use without rapid wear. The 50 mm length offers sufficient engagement for most short‑reach checks while remaining easy to handle by a single operator. The workshop execution prioritises resilience and straightforward operation, reducing the risk of damage during everyday tasks and supporting faster inspection cycles on the shop floor. Simple integration into inspection and set‑up routines As a compact, single‑piece test pin, the component slots directly into existing plug‑gauge sets, fixture checks or tool‑setting procedures. The solid design minimises sources of error and streamlines visual and tactile assessments of bore conformity. Supplied in a protective case, the pin is ready for safe storage and transport between workstations, helping maintain geometric integrity and ensuring the same reference can be relied upon across multiple checks. For workshop‑grade fit testing with the Metav IndustryLine gauge pin M323.B52, contact Metav Werkzeuge for purchase or tailored application support — call +49 2822 7131930 or email info@metav-werkzeuge.com to arrange immediate dispatch from Emmerich Technical data Article number: M323.B52 GTIN: 4061905065231 SKU: M323.B52 Manufacturer: Metav IndustryLine Key figures Diameter: 11.52 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.1 kg Features Material: special steel Workshop execution Delivered in protective case Category: Messstifte FAQ What tolerance does this gauge pin offer? The gauge pin M323.B52 (Metav IndustryLine) is specified with a tolerance of ±0.002 mm, making it suitable for precise plug‑fit and end‑measure checks. What is the pin made from? This M323.B52 test pin is manufactured from special steel designed for workshop durability and repeated use. Is the pin supplied ready for transport and storage? Yes — the M323.B52 is delivered in a protective case to preserve the gauge geometry during transport and storage. For which inspection tasks is this pin recommended? The pin is ideal for quick go/no‑go plug‑fit checks, bore verification, fixture alignment and tool‑setting operations in workshop environments. What is the length and how does it affect use? With a 50 mm length, the pin gives adequate engagement for short‑reach checks while remaining easy to handle during repetitive inspection tasks. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
11.53mm Gauge Pin 50mm Length Workshop Version - Metav IndustryLine
Take advantage of the compact 11.53 mm diameter, the ±0.002 mm tolerance and the workshop‑grade special steel construction for reliable end‑measurements and consistent inspection throughput; order the gauge pin directly via Metav Werkzeuge or contact our consultants for application advice. Gauge pin, single — 11.53 mm diameter, 50 mm length (Metav IndustryLine) A single gauge pin designed for precision end‑measurements and fixture reference in workshop inspection and small‑part metrology. Workshop execution, hardened special steel Diameter 11.53 mm with ±0.002 mm tolerance Length 50 mm, compact micro‑range tool Supplied single in protective transport case Precision that keeps inspection fast and reliable The compact gauge pin is manufactured to an industrial ±0.002 mm tolerance, which ensures repeatable end‑measurements and minimises sorting rework in production control. Classified in the micro range (max 10–100 mm), this size is particularly suited to fine components where measurement stability and low flex are critical. By using a gauge pin with such a narrow tolerance, calibration cycles become more predictable and measurement uncertainty is reduced, supporting faster decision making on the shop floor and through the quality process. Workshop‑ready design for repeatable use and handling Constructed from special steel and specified as a workshop execution, the pin combines surface resilience with dimensional stability during everyday handling. The 50 mm length balances accessibility with rigidity, making it simple to position in fixtures or bores without excessive operator force. Supplied single and protected in a transport case, the pin arrives ready for safe storage and immediate use, which helps preserve the calibrated state and extends tool life under typical workshop conditions. Integrates into inspection routines and tooling setups As a straightforward reference element, the pin fits into setting blocks, plug gauges and assembly jigs to provide a fixed datum or stop. Its compact form factor enables use in tight assemblies and on small fixtures, while the precise diameter delivers a reliable contact surface for comparative checks and go/no‑go operations. Compatibility with standard inspection workflows reduces setup time and supports consistent traceability when paired with Metav’s logistic and documentation routines. Speak to Metav Werkzeuge for tailored advice or to secure this workshop‑grade gauge pin (M323.B53) with 11.53 mm diameter and ±0.002 mm tolerance — call +49 2822 7131930 or email info@metav-werkzeuge.com Technical data Article number: M323.B53 GTIN: 4061905065248 Manufacturer: Metav IndustryLine Material: Special steel Diameter: 11.53 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.1 kg Packaging: delivered in protective transport case Execution: Workshop version Classification: Micro range (max 10–100 mm) Category: Gauge pin FAQ What is the intended use for this gauge pin? The gauge pin is intended as a precision reference for end‑measurements, fixture alignment and small‑part inspection; the M323.B53 from Metav IndustryLine serves as a compact datum or stop in workshop metrology. Is the pin supplied ready for use or does it require additional preparation? The item is supplied single and protected in a transport case; the pin is ready for immediate use after removal from its packaging and routine cleaning. How does the ±0.002 mm tolerance affect inspection outcomes? A tolerance of ±0.002 mm reduces measurement uncertainty and improves repeatability when using the pin as a reference, helping to avoid unnecessary rework and to maintain consistent quality control. Can this gauge pin be used in heavy‑duty environments? The workshop execution and special steel construction make the pin suitable for regular shop use; for harsher or high‑temperature environments, consult Metav Werkzeuge for material and handling recommendations. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
11.54mm Gauge Pin, 50mm Length, Special Steel, Workshop Version, Delivered in Case - Metav IndustryLine
Reliable workshop gauge pin combining durability and high precision: ±0.002 mm tolerance and special steel construction ensure consistent end-measurement results; order the gauge pin directly via Metav Werkzeuge or ask our consultants if needed. Gauge pin, single — Ø 11.54 mm, length 50 mm | Metav IndustryLine The gauge pin Ø 11.54 mm, length 50 mm is a compact inspection pin designed for precise end-face and diameter checks in workshop environments. Single gauge pin Ø 11.54 mm, length 50 mm Workshop-grade special steel construction Dimensional tolerance ±0.002 mm for precise checks Supplied in a transport case for safe storage Engineered accuracy for reliable end measurements The compact inspection pin is designed to deliver repeatable end-measurement results in routine quality checks. With a declared tolerance of ±0.002 mm, the pin supports fine verification tasks where small deviations matter. The short, rigid geometry and a calibrated shaft diameter make the component suitable for quick pass/fail checks and reference measurements on turned parts, bores or mating faces. The tight tolerance reduces rework and inspection cycles, improving throughput and ensuring components meet dimensional specifications without time-consuming secondary checks. Robust construction for everyday workshop use Manufactured from special steel, the pin combines wear resistance with dimensional stability under typical workshop conditions. The 50 mm length and compact diameter make the pin easy to handle and position in gauges, fixtures or assembly jigs, while the material choice preserves accuracy over prolonged use. The workshop specification indicates a build intended for daily operation rather than delicate laboratory handling, so the measuring pin withstands routine handling, cleaning and storage without rapid loss of form. This durability translates into lower replacement frequency and dependable performance on the shop floor. Practical handling, traceability and storage benefits Delivery in a protective transport case secures the measuring pin during storage and transport, reducing the risk of incidental damage that could compromise the ±0.002 mm accuracy. The single-pin format supports modular inspection strategies: individual pins can be swapped into go/no-go fixtures or combined into sets for series inspection. Clear identification with SKU and GTIN simplifies inventory and traceability, supporting quality records and incoming inspection workflows. The compact nature of the pin also eases integration into existing gauges and does not demand special handling equipment. For application advice or to arrange supply of Metav IndustryLine gauge pins, contact Metav Werkzeuge for a tailored recommendation and delivery from Emmerich. Technical data Article number: M323.B54 GTIN: 4061905065255 Label: Gauge pin, single, Ø 11.54 mm, length 50 mm Brand: Metav IndustryLine Material: Special steel Weight: 0.1 kg Facts Diameter: 11.54 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.1 kg SKU: M323.B54 Special features Workshop version Supplied in transport case Single inspection pin Compact geometry for end-measurement checks FAQ What inspection tasks is this gauge pin suited for? The gauge pin is intended for end-face and diameter verification on turned parts and bores; the Ø 11.54 mm measuring pin supports pass/fail checks and reference measurements in production. Is the dimensional accuracy of the pin documented? Yes, the measuring pin is supplied with a declared tolerance of ±0.002 mm; traceability is supported via SKU M323.B54 and GTIN 4061905065255. Which material is used and how does it affect durability? The pin is made from special steel, chosen for wear resistance and stability under workshop conditions, which helps preserve dimensional integrity over repeated use. Can the pin be integrated into existing gauges or fixtures? The compact form and standard diameter enable straightforward integration into go/no-go fixtures, plug checks and modular gauge holders used in routine inspection processes. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
11.55mm Test Pin Single 50mm Length Workshop Version - Metav IndustryLine
Benefit from workshop-grade reliability and pinpoint repeatability: the combination of ±0.002 mm tolerance and a special steel shaft ensures consistent end‑dimension checks, while delivery in a protective transport case preserves accuracy in daily use. Order via Metav Werkzeuge or consult our specialists for application advice. Gauge pin, single, Ø11.55 mm, length 50 mm — Metav IndustryLine The Gauge pin, single, Ø11.55 mm, length 50 mm is a compact, workshop‑grade reference pin for precise end‑dimension checking and fixture set‑up in small‑part production and inspection. Workshop-grade construction for durable daily use Diameter Ø11.55 mm with ±0.002 mm tolerance 50 mm hardened special-steel shaft Delivered in protective transport case Accuracy that secures measurement decisions This compact reference pin, specified at ±0.002 mm positional variation, provides a level of repeatability suitable for fine inspection tasks where small deviations matter. Placing the component measurement against a defined cylindrical reference reduces interpretation variance and supports reproducible results. Classified in the micro measurement range for compact gauges, the item is well matched to precision tasks in tooling, small‑component assembly and quality control where consistent end‑dimension data are required. Built for everyday workshop use and safe handling A special steel shaft and workshop‑grade finish combine wear resistance with straightforward handling. The 50 mm working length balances reach and stiffness, allowing secure engagement without excessive overhang. Supplied in a protective transport case, the pin is protected from knocks and contamination between uses, which preserves the reference surface and extends service life. The compact mass also simplifies manual positioning during repeated checks. Practical role in inspection and fixture alignment Designed for end‑dimension checks and as a reference for setting-up jigs, this precision pin is particularly useful when fixed gauges are impractical. Its defined Ø11.55 mm diameter aids in verifying bore sizes, alignment features and mating parts during assembly stages. Using a dedicated reference pin reduces measurement uncertainty introduced by variable clamping and supports rapid comparison checks on production lines or in the workshop. Reliability delivered by a specialist supplier Sourced under the Metav IndustryLine label, the component benefits from a supplier network that emphasises traceable stock and dependable delivery. For workshops and smaller production facilities, that supply reliability turns into fewer interruptions and a more predictable inspection routine. The compact format and durable construction mean the pin integrates easily into existing test benches and carrying kits. For workshop applications requiring a compact, high‑repeatability reference, request the Metav IndustryLine gauge pin M323.B55 from Metav Werkzeuge or contact our technical advisors at info@metav-werkzeuge.com / +49 2822 7131930 to discuss suitability for specific inspection tasks Technical Data Article number: M323.B55 GTIN: 4061905065262 Brand: Metav IndustryLine Facts Diameter: 11.55 mm Length: 50 mm Tolerance / repeatability: ±0.002 mm Weight: 0.1 kg Measurement range: 11.55 mm Special features Material: special steel Workshop execution Delivered in protective transport case Category: gauge pins (messstifte) FAQ What applications suit this gauge pin best? This gauge pin (brand Metav IndustryLine, SKU M323.B55) is intended for end‑dimension checks, fixture set‑up and alignment tasks in workshops and inspection benches where compact, repeatable references are required. Is the pin suitable for everyday production use? Yes; the workshop‑grade finish and special‑steel construction make the pin robust for routine production sampling and repeated reference measurements. How precise is the measurement reference provided by the pin? The pin offers a positional variation of ±0.002 mm, providing high repeatability for fine inspection tasks and small‑part quality control. Does the delivery include protection for transport? The pin is supplied in a protective transport case to reduce the risk of transport damage and surface contamination during storage. Can this gauge pin be used for bore verification? Its defined Ø11.55 mm diameter makes it suitable as a reference for verifying bore sizes and for quick go/no‑go comparisons in assembly or inspection processes. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
11.56mm Gauge Pin Length 50mm Workshop Finish - Metav IndustryLine
Take advantage of a compact, workshop-grade measuring solution with repeatable accuracy and robust material properties. The combination of a 11.56 mm gauge diameter, a 50 mm usable length and a dimensional tolerance of ±0.002 mm supports reliable end‑measurement tasks and simple integration into inspection routines — order directly via Metav Werkzeuge or consult the technical advisors for specification matching. M323.B56 gauge pin — single, Ø 11.56 mm, 50 mm length (Metav IndustryLine) M323.B56 is a single gauge pin designed for end‑measurement and reference checks in workshop environments Workshop-grade construction for daily use Diameter 11.56 mm with tight tolerance Solid special steel for wear resistance Tolerance ±0.002 mm for high repeatability Accuracy tailored to end‑measurement tasks The compact pin delivers a repeatable tolerance of ±0.002 mm, which makes it suitable for precision end measurements and small-bore checks where reproducibility matters. As a fixed‑diameter measuring element, the gauge pin functions as a reliable reference when checking bore seating, alignment or component end sizes. The high nominal diameter of 11.56 mm combined with the short 50 mm length minimises lever arm effects, helping to reduce measurement uncertainty in short‑reach applications. Built to withstand workshop conditions Crafted from special steel, this measuring pin is optimised for frequent handling and contact checks. The workshop‑grade design focuses on wear resistance and dimensional stability over repeated use, so maintenance intervals remain low and inspection workflows run smoothly. The compact form factor also contributes to easy storage and fast part‑to‑part comparison during routine quality control. Practical use and handling benefits The single gauge pin is intended for straightforward end‑measurement and verification tasks on production and assembly benches. Mounted as a reference or used as a manual plug gauge, the pin simplifies go/no‑go style checks and quick dimensional confirmations. The short length ensures minimal deflection when inserted into bores or pressed against mating surfaces, and the solid steel construction supports consistent tactile feedback during manual inspection. Ordering, traceability and workshop integration As a dedicated workshop gauge, the pin is labelled and ready for direct integration into inspection sets or fixture complements. The compact dimensions and clear specification make it suitable as a replacement or standardised reference element in small‑part production. For procurement and inventory planning, reference the item by SKU M323.B56 and the Metav IndustryLine designation when specifying compatible inspection kits. Contact Metav Werkzeuge for availability and technical matching of the Metav IndustryLine M323.B56 gauge pin to specific measurement setups Technical data SKU: M323.B56 GTIN: 4061905066146 Description: Gauge pin, single, Ø 11.56 mm, length 50 mm Manufacturer: Metav IndustryLine Specifications Diameter: 11.56 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.1 kg Features Material: special steel Version: workshop execution Category: gauge pin (single) FAQ What are the exact dimensions of the M323.B56 gauge pin? The M323.B56 gauge pin has a nominal diameter of 11.56 mm and a usable length of 50 mm, supplied as a single measuring element. What level of accuracy can be expected from this gauge pin? The Metav IndustryLine M323.B56 is specified with a dimensional tolerance of ±0.002 mm, providing high repeatability for end‑measurement checks. For which tasks is this gauge pin intended? This single gauge pin is intended for end‑measurements, bore seating checks and quick reference inspections in workshop and production environments. What material is used for the pin and how does that affect durability? The pin is made from special steel, giving improved wear resistance and dimensional stability for repeated workshop use. How should the M323.B56 be referenced when ordering or specifying? Order or specify the item using the SKU M323.B56 and the Metav IndustryLine designation to ensure correct selection. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
11.57mm Gauge Pin 50mm Length Workshop Version - Metav IndustryLine
Take advantage of a compact, high-precision gauge pin that combines a finely ground 11.57 mm diameter with a short 50 mm length and a tight ±0.002 mm tolerance for reliable go/no-go and setting tasks; order directly via Metav Werkzeuge or consult the technical team for application advice. Gauge pin M323.B57 — 11.57 mm diameter, 50 mm length (Metav IndustryLine) A gauge pin designed for accurate dimensional checks and plug-fit verification in workshop metrology, available in a robust workshop execution. Precisely ground 11.57 mm diameter 50 mm length for compact checks Tolerance ±0.002 mm for tight fits Workshop execution, robust design Precision where small tolerances matter This instrument delivers repeatable results in tasks that demand micrometric control. The combination of a finely finished 11.57 mm diameter and a stated ±0.002 mm positional tolerance makes it suitable for checking bore sizes, verifying plug fits and setting end gauges in small assemblies. The short 50 mm overall length reduces flex and improves handling during manual inspections, so measurements remain consistent even when the operator must work quickly. The use of special steel provides dimensional stability and wear resistance, ensuring the component maintains precision over many cycles. Designed for workshop practice and efficient workflows The workshop execution reflects practical details that support everyday use on the shop floor: compact dimensions for easy storage in tool drawers, a weight of around 0.1 kg for comfortable manipulation, and a construction aimed at robustness rather than laboratory fragility. These characteristics shorten inspection cycles and reduce set‑up time when comparing shafts, pins or bores against a reference size. As a practical tool for production control, the part helps maintain throughput while keeping quality checks straightforward and reliable. Integration into inspection routines and traceability As a purpose-made inspection pin, the M323.B57 fits seamlessly into existing measurement routines for small to medium components. Its clear numerical specification supports documentation in quality protocols and simplifies decisions about gauging strategy: use for functional go/no-go checks, reference setting or comparative inspection of mating parts. The numerical values printed here (diameter 11.57 mm, length 50 mm, tolerance ±0.002 mm) provide an objective basis for procurement and quality planning and help align workshop practice with measurable performance targets. Contact Metav Werkzeuge today to request the M323.B57 gauge pin or to discuss its suitability for specific inspection tasks via info@metav-werkzeuge.com or +49 2822 7131930 Technical Data Article number: M323.B57 GTIN: 4061905066399 Manufacturer: Metav IndustryLine Material: Special steel Weight: 0.1 kg Diameter: 11.57 mm Length: 50 mm Tolerance: ±0.002 mm Facts Diameter: 11.57 mm Length: 50 mm Weight: 0.1 kg Tolerance: ±0.002 mm GTIN: 4061905066399 Special features Workshop execution Category: Messstifte (gauge pins) Label: Prüfstift, einzeln, 11,57 mm Länge 50 mm SKU: M323.B57 FAQ What inspection tasks is this gauge pin suitable for? This gauge pin M323.B57 is suitable for plug-fit verification, go/no-go checks and setting reference gauges in workshop metrology applications. What material is the pin made from and why does it matter? The pin is made from special steel, which gives the M323.B57 good wear resistance and dimensional stability for repeated inspection cycles. How tight is the dimensional specification of the pin? The pin is specified with a tolerance of ±0.002 mm, providing the level of precision required for close-fit inspections and high-quality assembly checks. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
Fast, tactile checks where electronics are impractical
Gauges and test pins provide unequivocal go/no-go results for threads, bores, gaps and radii without relying on electronics. The range covers plug gauges and ring gauges for internal and external threads, feeler gauges and precision feeler strips for micro‑gap assessment, plus probe pins and measuring pins for tactile diameter and pitch checks.
How these tools work in the production environment
Mechanical gauges operate as direct reference standards: a plug gauge or ring gauge verifies conformity to thread profiles and mating ability, while limit gauges separate accept from reject in a single step. Test pins are used to tactilely measure small bore diameters, centre‑to‑centre distances and radii. Manufactured from hardened gauge steel or ceramic and often precision lapped, these instruments deliver immediate physical results that are ideal for incoming inspection, machine‑side checks and final control.
Measurable benefits that affect production performance
- Reduced scrap and rework through rapid, unambiguous pass/fail assessment.
- Increased repeatability thanks to very low measurement uncertainty and fine lapping.
- Lower downtime: quick checks at the machine save cycle time and reduce setup periods.
- Durable construction with high wear resistance from specialised, low‑distortion alloys.
- Versatile delivery formats: individual gauges, organised sets in wooden cases or metre‑length feeler rolls compliant with DIN 2269.
Why Metav is the practical choice for precision supplies
Metav combines decades of expertise with a broad warehouse and quality filtering from Emmerich. As a precision partner for industry, craft and trade, Metav supplies a comprehensive selection of gauges and test pins alongside complementary tools such as precision calipers and setting rings. With over 48,000 customers and a catalogue exceeding 250,000 items, Metav is positioned to supply reliably, reduce vendor complexity and support traceable quality control to national standards.
Summary
Gauges and test pins are indispensable for dependable, repeatable quality assurance where tactile, mechanical verification is preferred. Choose these plug gauges, ring gauges, feeler strips and probe pins when immediate, robust measurement decisions are required on the shop floor.
FAQ
What materials are gauges and test pins typically made from?
Gauges and test pins are usually manufactured from hardened gauge steel for durability and wear resistance; ceramic variants are available where thermal stability and minimal wear are critical.
How do thread gauges ensure mating capability?
Thread plug gauges and ring gauges check flank diameters and thread form against standards, providing a clear go/no‑go verdict that confirms pairability with mating parts.
Which tolerance class should I choose for probe pins and gauge sets?
Select tolerance classes aligned with your inspection requirements; for high‑precision tasks, sets produced to DIN 2269 or equivalent tolerance classes ensure micrometre‑level control and repeatability.
Can feeler gauges measure contact gaps in valve and engine work reliably?
Yes. Feeler gauges and precision feeler strips, supplied either as a fan or metre‑length rolls, allow accurate assessment of valve clearances and contact gaps down to micrometre increments.
How do limit gauges speed up in‑process inspection?
Limit gauges separate good from bad in a single, tactile operation, enabling rapid go/no‑go checks at the machine and reducing both inspection time and the likelihood of human interpretation errors.
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com