Precision gauge blocks and plug gauges for reliable dimensional control
Mechanical gauge blocks and plug gauges are essential for tactile verification of threads, bores and gap dimensions, providing fast, unambiguous go/no-go results that enhance process reliability and reduce scrap. Designed for industrial metalworking and toolmaking, these precision tools support incoming inspection and final quality checks by delivering traceable measurements in applications such as thread inspection, bore diameter testing and spacing checks. Manufactured from specially hardened, low-distortion alloys and fine-lapped for minimal measurement uncertainty, the range includes thread plug gauges, precision plug gauges and calibration gauge blocks to ensure long-term repeatability and wear resistance.
10.94mm Gauge Pin, Single, 50mm Length, Workshop Version - Metav IndustryLine
Take advantage of the combination of ±0.002 mm tolerance, Special steel workshop construction and the compact 50 mm length for reliable end‑measure checks; order the gauge pin directly via Metav Werkzeuge or ask our consultants if needed. Gauge pin, single, 10.94 mm — 50 mm length (Metav IndustryLine workshop version) The gauge pin, single, 10.94 mm is a compact reference pin for precise end‑measure and go/no‑go checks in workshop inspection routines. Workshop version for daily use Diameter 10.94 mm for tight fits Length 50 mm for compact checks Tolerance ±0.002 mm for precise inspection Precision that keeps production moving The workshop‑grade pin provides a consistently low tolerance of ±0.002 mm, which translates into fewer false rejects and faster verification cycles on the shop floor. With a nominal diameter of 10.94 mm, the pin functions as a reliable reference for end‑measure operations and fixture checks. This stability reduces rework and shortens decision loops during quality control, supporting a smoother production flow and better utilisation of inspection resources. Built for everyday handling and repeatability Manufactured from Special steel and finished for workshop use, the pin combines surface durability with dimensional integrity across repeated insertions. At 50 mm overall length and approximately 0.1 kg mass the component is compact to manoeuvre yet robust enough for daily handling. Supplied as a single item and protected for transport in a dedicated transport box, the design minimises transit damage and enables immediate deployment in assembly or inspection stations. Easy integration into existing inspection routines Classified in the Micro range (10–100 mm), this precision reference pin slots into standard gauge blocks, fixtures and manual measuring jigs without the need for extensive adaptation. The simple geometry supports quick visual checks and tactile go/no‑go tests, while the documented tolerance makes it straightforward to include the pin in inspection protocols and reporting. The compact format supports tight‑space applications where consistent roundness and diameter control are essential for fit and function verification. Secure workshop accuracy with Metav IndustryLine gauge pins—contact Metav Werkzeuge for specification support and supply from Emmerich; email info@metav-werkzeuge.com or call +49 2822 7131930 Technical Data Article number: M323.A94 GTIN: 4061905064814 SKU: M323.A94 Material: Special steel Category: Gauge pins Facts Diameter: 10.94 mm Length: 50 mm Weight: 0.1 kg Accuracy: ±0.002 mm Special features Workshop version Supplied as single piece Delivered in transport box Compact format for end‑measure checks FAQ What is the exact diameter of the gauge pin? The gauge pin has a diameter of 10.94 mm (SKU M323.A94) and is supplied by Metav IndustryLine as a single reference pin. What accuracy does the pin provide? The pin is specified to an accuracy of ±0.002 mm, suitable for tight tolerance go/no‑go and reference checks. How long is the pin and what is its weight? The pin measures 50 mm in length and weighs approximately 0.1 kg, offering a compact but sturdy reference standard. Is the pin intended for workshop use or laboratory calibration? This is a workshop version designed for everyday inspection and fixture checks; it is supplied as a single piece and protected for transport. Which measurement range classification applies to this pin? With a diameter of 10.94 mm the component falls into the Micro classification (10–100 mm), optimised for small‑part inspection and fine‑mechanical applications. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
10.95mm Gauge Pin Single 50mm Length Workshop Version - Metav IndustryLine
Take advantage of the combination of tight tolerance ±0.002 mm, workshop-grade construction and compact handling to secure reproducible end‑dimension checks; order the gauge pin directly via Metav Werkzeuge or ask our consultants for application advice. Gauge pin M323.A95 – Single gauge pin, Ø 10.95 mm, length 50 mm (Metav IndustryLine) A single gauge pin (M323.A95) designed for precise end‑measure and plug‑gauge checks in workshop and inspection routines. Single gauge pin Ø 10.95 mm Length 50 mm, workshop execution Tight tolerance ±0.002 mm Special steel for dimensional stability Reproducible accuracy for routine inspection The compact design delivers consistent measurement results where repeatability matters. With a declared positional tolerance of ±0.002 mm, this gauge pin is suited to production sampling and final‑size verification, reducing uncertainty in serial checks. The hard, precision‑ground circumference provides a reliable reference surface that minimises bearing errors and keeps run‑out low during plug or bore tests. For quality engineers and inspection technicians, the clear numeric tolerance streamlines acceptance criteria and supports traceable quality control. Robust workshop design with secure handling Manufactured in special steel and finished in a workshop execution, the item is built for daily use without sacrificing finesse. The 50 mm length and compact diameter make it easy to position in fixtures and jigs while the short, stiff geometry reduces bending and handling errors during measurement. Delivery in a transport case protects the pin in transit and storage, preserving the calibrated surface and ensuring the tool arrives ready for immediate use on the bench or in the gauge block set. Micro‑range sizing for fine mechanical components With a measurement size of Ø 10.95 mm, this instrument falls into the micro category (measurement range up to 100 mm), which is the standard for fine mechanical work such as small bores, assemblies and watch‑type components. The small footprint and high straightness make it ideal for testing end dimensions, seating checks and go/no‑go verifications in confined spaces. Integration into existing inspection sequences is straightforward, and the high material stability supports consistent thermal behaviour across normal shop temperatures. For workshop‑grade precision choose the Metav IndustryLine gauge pin M323.A95; contact Metav Werkzeuge for procurement or technical advice at info@metav-werkzeuge.com or call +49 2822 7131930 Technical data SKU: M323.A95 GTIN: 4061905064821 Category: Messstifte Facts Diameter: Ø 10.95 mm Length: 50 mm Measurement range min/max: 10.95 mm / 10.95 mm Tolerance: ±0.002 mm Weight: 0.1 kg Special features Material: Special steel Delivery: Transport case for protection during shipping Version: Single item, workshop execution FAQ What checks is this gauge pin intended for? This gauge pin M323.A95 is intended for end‑dimension and plug checks in inspection and workshop routines, providing a defined diameter reference for bore and seating measurements. Is the tolerance suitable for serial inspection tasks? Yes, the declared tolerance of ±0.002 mm on the Metav IndustryLine gauge pin M323.A95 supports reproducible sampling and acceptance checks in production environments. How is the gauge pin delivered and protected? The item is supplied in a transport case to protect the precision surface during shipping and storage, ensuring the Metav IndustryLine gauge pin arrives ready for use. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
10.96mm Gauge Pin 50mm Length Workshop Version, Special Steel - Metav IndustryLine
Combining ±0.002 mm repeatability with a 10.96 mm nominal diameter and a robust special steel construction, this gauge pin delivers reliable, reproducible inspection results for workshop routines and quality checks. Order the item directly via Metav Werkzeuge or consult our advisors for application guidance. Gauge pin M323.A96 — 10.96 mm Ø, 50 mm length (Metav IndustryLine) A gauge pin designed as a compact inspection pin for quick bore checks and reference measurements in workshop and production environments. Workshop version for robust, daily use Diameter 10.96 mm with ±0.002 mm tolerance Length 50 mm for standard inspection tasks Made from special steel for durability Accurate measurement as foundation for faster decision-making The pin offers an accuracy of ±0.002 mm, a tolerance level that supports precise fit checks and clear go/no‑go assessments during incoming inspection or in‑process control. The close dimensional control reduces uncertainty in pass/fail decisions, which shortens inspection loops and minimises rework. When used as a reference probe in gauge sets or in fixture checks, the consistent diameter measurement assists traceable quality records and repeatable assembly tolerances. Robust design that suits daily workshop handling Constructed from special steel and specified as a workshop execution, this inspection pin tolerates frequent handling and contact with measuring fixtures. The 50 mm working length and compact form factor make the pin easy to seat in bore gauges, adaptors or fixture receivers while maintaining low flex and stable contact. The material choice balances wear resistance and machinability so the pin retains its geometry over many cycles, supporting longer maintenance intervals and predictable lifetime performance. Simple integration into quality workflows and traceability Marked with SKU M323.A96 and GTIN for inventory control, the component is straightforward to document in parts lists and inspection plans. Its nominal diameter of 10.96 mm makes the pin suitable as a reference for small-bore checks or as part of stepped gauge arrays. Clear technical specification and standardised identification streamline stockkeeping, enable fast replacements and support consistent audit trails in production environments. Contact Metav Werkzeuge for availability, batch information and how the Metav IndustryLine gauge pins can be included in existing inspection programmes Technical data Article number: M323.A96 GTIN: 4061905064838 Manufacturer: Metav IndustryLine Facts Diameter: 10.96 mm Length: 50 mm Accuracy (variation): ±0.002 mm Weight: 0.1 kg Special features Material: special steel Workshop execution Category: Gauge pin / Inspection pin SKU: M323.A96 FAQ What is the dimensional tolerance of this gauge pin? The gauge pin is specified with a dimensional variation of ±0.002 mm for the nominal 10.96 mm diameter (SKU M323.A96), providing tight repeatability for inspection tasks. Which applications is this inspection pin suitable for? This inspection pin is intended for bore and fit checks, fixture verification and small‑bore reference measurements in workshop and production inspection routines. What material is used and how does it affect durability? The pin is made from special steel, chosen for wear resistance and stability under frequent handling, which supports prolonged geometric retention during regular inspection use. Is the gauge pin supplied with an identification code for traceability? Yes, the item is identified by SKU M323.A96 and GTIN 4061905064838 for straightforward traceability in stock and quality documentation. Can this pin be used as a replacement in gauge sets? The compact form and standardised diameter make the pin suitable as a replacement element in many gauge arrays and small‑bore checking assemblies, subject to the set’s matching dimensions. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
10.97mm Gauge Pin Single 50mm Length Workshop Finish - Metav IndustryLine
Take advantage of precise diameter control, durable workshop design and practical length for reliable end‑gauging tasks; order this gauge pin directly via Metav Werkzeuge or consult our specialists for application advice. Gauge pin, single — 10.97 mm diameter | Workshop version (Metav IndustryLine) The gauge pin, single, 10.97 mm is a hardened precision end‑measure pin for go/no‑go and limit checks in workshop and production settings, supplied in a protective case for safe transport Workshop design for durable handling Diameter 10.97 mm ±0.002 mm tolerance 50 mm length for recessed features Supplied in protective case for transport Repeatable diameter control for assembly and inspection The hardened special steel construction and the defined tolerance of ±0.002 mm ensure repeatable checks on shafts, bores and seating surfaces. As a compact precision tool it delivers a consistent physical reference that reduces interpretation error compared with visual gauges; the numeric accuracy translates directly into measurable quality control benefits during incoming inspection and final assembly. The small mass and robust material mean the gauge pin resists wear while maintaining form, supporting reproducible results across production runs. Practical format that fits workshop workflows With a 10.97 mm nominal diameter and 50 mm length, this single gauge pin is designed for accessibility into moderate recesses and alignment tasks. The workshop version prioritises ease of handling and resistance to knocks, making it suitable for routine in‑process checks on milling and turning centres. Supplied in a protective case, the component remains transport-safe between bench and machine, reducing downtime due to damaged gauges and simplifying storage logistics on a crowded shop floor. Direct applicability and procurement confidence As a straightforward, low‑complexity measuring element, the pin integrates into existing inspection routines without additional systems. Its classification within the micro range (10–100 mm) denotes an excellent compromise between reach and stiffness for precision small‑part work. Ordering through Metav Werkzeuge provides supply reliability from the European Emmerich hub and access to product advice if special variants or matched sets are required, enabling fast replenishment and minimal interruption to production. For technical advice or to secure supply of this Metav IndustryLine gauge pin (M323.A97) directly from Metav Werkzeuge in Emmerich, contact our team for tailored recommendations and prompt delivery. Technical data Article number: M323.A97 GTIN: 4061905064845 SKU: M323.A97 Material: special steel Nominal diameter: 10.97 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.1 kg Facts Category: Gauge pin Version: single pin, workshop execution Measurement range classification: Micro (10–100 mm) Intended use: end measurements, go/no‑go checks, alignment Special features Supplied in protective case for transport Robust workshop finish Suitable for repetitive production checks FAQ What degree of precision does the gauge pin offer? The gauge pin delivers a tolerance of ±0.002 mm, which is indicated for tight end‑measure checks and reliable go/no‑go control in production. Is the pin suitable for use in a production workshop environment? Yes; the workshop execution and special steel construction make the pin durable for routine in‑process inspection and handling on shop floors. Can this gauge pin be used for alignment and seating checks? The 10.97 mm diameter and 50 mm length are appropriate for alignment tasks and seating verifications where a compact, stiff reference is required. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
10.98mm Gauge Pin 50mm Length Workshop Version - Metav IndustryLine
Take advantage of ±0.002 mm tolerance, robust Special steel construction and a compact 50 mm length for repeatable go/no‑go checks; order the pin directly via Metav Werkzeuge or consult the team for application advice. Gauge pin M323.A98 — single test pin, 10.98 mm diameter (Metav IndustryLine) The gauge pin M323.A98 is a single test pin designed for precise end‑measurement and fit checks in workshop environments; a compact solution for small‑format inspection tasks. Workshop version for robust daily use Tolerance ±0.002 mm for repeatable checks 10.98 mm diameter for end‑measurement applications Supplied in a protective case for transport Precision for small‑format inspection and reliable go/no‑go checks This compact gauge pin has a nominal diameter of 10.98 mm and a verified manufacturing tolerance of ±0.002 mm, which positions it firmly in the micro class of measuring pins (ideal for measurement ranges up to 100 mm). The narrow diameter and tight tolerance make this component suitable for end‑measurement tasks and plug‑gauge comparisons where repeatability is essential. By choosing a pin with this accuracy, production and QC routines benefit from clear, reproducible results that reduce the need for secondary checks and minimise scrap rates. Built for workshop use with secure handling and transport Constructed from Special steel, the pin is finished to withstand everyday workshop conditions while retaining its measuring geometry. At a length of 50 mm, the pin combines sufficient engagement depth with easy handling; the workshop version designation emphasises durability and straightforward use during assembly, set‑up or incoming inspection. The unit is supplied in a protective case to secure the datum surface during transport — practical for workshop logistics and field work without implying long‑term storage suitability. Faster inspection cycles and simplified fit validation With its narrow tolerance band and compact design, this test pin supports efficient go/no‑go and fit checks in fixtures, jigs and assembly verifications. The precise diameter reduces uncertainty when checking bore fits and end measurements, contributing to faster decision cycles on the shop floor and fewer stoppages for rework. Combined with Metav’s supply chain reliability, the component helps maintain steady throughput by ensuring measuring aids are available when needed. Contact Metav Werkzeuge for tailored advice on integrating the Metav IndustryLine M323.A98 gauge pin into existing inspection routines and to arrange supply from Emmerich with dependable delivery and stock assurance Technical data SKU: M323.A98 GTIN: 4061905064852 ECLASS: 21170231 Core specifications Diameter: 10.98 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.1 kg Features Material: Special steel Version: Workshop version Delivery: Protective case for transport Intended use: end measurements Category: Gauge pins FAQ What is the nominal diameter and tolerance of the pin? The Metav IndustryLine M323.A98 gauge pin has a nominal diameter of 10.98 mm and a manufacturing tolerance of ±0.002 mm. Is the pin suitable for end‑measurement and plug‑gauge checks? Yes. The design and tolerance of the M323.A98 make it suitable for end‑measurement tasks and fit validation in fixtures where compact, repeatable measurement elements are required. How is the pin delivered and handled for transport? The pin is supplied in a protective case to safeguard the measuring faces during transport; the case is intended for transport protection rather than long‑term storage. Which material is used for the pin and what does that mean for workshop use? Manufactured from Special steel, the pin offers a balance of hardness and toughness suitable for routine workshop inspection and handling. Can the M323.A98 be used directly in production jigs and fixtures? Yes. The compact length (50 mm) and tight tolerance support direct use in jigs and fixtures for go/no‑go checks and end‑dimension verification. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
10.99mm Gauge Pin 50mm Length Workshop Finish - Metav IndustryLine
Take advantage of the combination of high repeatability, tight tolerance (±0.002 mm) and compact handling for reliable in‑process checks; order the gauge pin directly via Metav Werkzeuge or consult Metav’s specialists for application advice. Gauge pin, single — 10.99 mm diameter, 50 mm length (Metav IndustryLine) Gauge pin M323.A99 provides a compact solution for end‑dimension checks and assembly verification in precision workshops and inspection benches. Workshop-grade construction Diameter controlled to ±0.002 mm Single piece for individual inspection tasks Consistent, traceable measurements for small bores The 10.99 mm diameter pin is manufactured for reproducible checking of end dimensions and small bore clearances, delivering a tolerance of ±0.002 mm that supports reliable go/no‑go assessments and fine inspection tasks. As a precision measuring element, the pin minimises cumulative measurement uncertainty when used in comparative setups or alongside gauge blocks. This level of control reduces rework rates and secures process stability in serial checking. Robust workshop construction with precise handling Built in a workshop‑grade execution from special steel, the pin balances wear resistance and dimensional stability across repeated insertions. The 50 mm overall length provides adequate reach for many component depths while remaining easy to guide by hand or fixture, and the modest mass (approx. 0.1 kg) helps to avoid inadvertent deflection during manual checks. The single‑piece supply format is suitable for dedicated test benches and simplifies inventory management for small‑batch quality control. Easy integration into quality routines and documentation Designed for straightforward incorporation into standard inspection procedures, the measuring pin complements plug and ring gauge sets or custom jigs for repeat inspections. Clear item identification and the compact form factor enable fast deployment on control plans and audit checklists. When traceability is required, the pin’s consistent geometry supports stable reference readings, helping to maintain documentation continuity across shifts and operators. Contact Metav Werkzeuge today to discuss how the Metav IndustryLine gauge pin M323.A99 can be matched to existing inspection fixtures or to request specialist advice on implementing it into production control. Technical data Article number: M323.A99 GTIN: 4061905065590 Label: Gauge pin, single, 10.99 mm, length 50 mm Manufacturer: Metav IndustryLine Facts Diameter: 10.99 mm Length: 50 mm Accuracy: ±0.002 mm Weight: 0.1 kg Special features Workshop execution Material: special steel Supplied individually Application: end‑dimension checks FAQ What is the exact diameter and tolerance of the pin? The gauge pin has a diameter of 10.99 mm with a manufacturing tolerance of ±0.002 mm, specified for precise end‑dimension checks. Is this pin suitable for use in small‑bore inspection fixtures? Yes, the design and 50 mm length of the gauge pin make it suitable for small‑bore fixtures and many bench inspection setups, supporting consistent engagement and repeatable readings. Can this pin be used as a reference for go/no‑go assessments? The pin’s tight tolerance and stable geometry mean it can be used as a reference element in go/no‑go routines and comparative checks when documented in the inspection plan. How is the gauge pin supplied and identified? The item is supplied individually under the article number M323.A99 and GTIN 4061905065590, facilitating clear identification in stock and inspection records. Which material is the pin made from and what does that mean for durability? Manufactured from special steel, the pin offers enhanced surface endurance and dimensional stability for repeated mechanical engagement in workshop environments. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
100 mm Limit Plug Gauge H7, Hardened Gauge Steel, DIN 2245 - Metav IndustryLine
Take advantage of a robust inspection tool that combines compliance with DIN 2245, an H7 tolerance check and a hardened gauge‑steel construction for reliable in‑process assessment; order directly via Metav Werkzeuge or consult the Metav team for specification support. Limit plug gauge M314.100, 100.0 mm H7, Metav IndustryLine A Limit plug gauge M314.100 designed for fast verification of H7 bore tolerances in production and inspection environments. DIN 2245 compliant design H7 tolerance checking for bores Hardened gauge steel construction Clear SKU and GTIN identification Fast, standardised bore verification that reduces rework The M314.100 is built to the DIN 2245 specification and intended for quick go/no‑go checks of bores specified to H7. By offering a straightforward, mechanical acceptance test, the gauge shortens inspection cycles and reduces subjective judgement at the machine or inspection bench. The hardened design ensures consistent contact geometry, which supports repeatable measurements and helps to minimise scrap and rework through rapid pass/fail decisions. Robust construction for the workshop and production line Manufactured from hardened gauge steel, this plug gauge withstands routine handling on the shop floor while retaining the contact integrity required for reliable gauging. The material choice and finish provide wear resistance and stable dimensions during regular use, which translates into prolonged service life and fewer replacements. The construction is optimised for frequent insertion and removal, keeping downtime low and inspection throughput high. Traceability and simple integration into quality routines Identification via SKU and GTIN simplifies inventory control and traceability within quality management systems. The gauge’s conformity to established standards supports consistent documentation and auditability in production records. As a Metav IndustryLine product, it benefits from the distributor’s European quality filter and logistics base in Emmerich, making supply and replacement straightforward for workshops and inspection departments. For supply, technical details or application guidance with the Metav IndustryLine plug gauge, contact Metav Werkzeuge in Emmerich for personalised assistance and reliable delivery. Technical data Article number: M314.100 GTIN: 4054469121949 Norm: DIN 2245 Material: gauge steel, hardened Diameter: 100 mm EClass: 21170218 Facts Diameter: 100 mm GTIN: 4054469121949 Customs tariff number: 90173000 SKU: M314.100 Special features H7 tolerance for bore inspection Manufactured to DIN 2245 Category: gauges / plug gauges Brand: Metav IndustryLine FAQ What is this gauge used for? The limit plug gauge M314.100 is used to verify whether bores meet the specified H7 tolerance and to provide a rapid go/no‑go assessment in production and inspection workflows. Which standard does the gauge comply with? The gauge is manufactured to DIN 2245, ensuring established dimensions and design suited for standard bore inspection tasks. What material is the gauge made from? The plug gauge is produced from hardened gauge steel, selected for durability and dimensional stability under routine workshop use. How does the gauge fit into quality documentation? The gauge includes a clear SKU and GTIN for inventory and traceability, facilitating integration into inspection records and production audits. Is this product suitable for shop‑floor use? Yes. As a Metav IndustryLine product, the gauge is intended for robust use in workshops and inspection areas where quick, standardised checks are required. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
1000 mm Precision Feeler Gauge Set With Ring, Tapered Blades 0.05–1.00 mm, 20‑Piece - Metav IndustryLine
Take advantage of the combination of fine increments, a robust ring mounting and a conical blade geometry for reliable gap setting and repeatable inspection results; order the set directly via Metav Werkzeuge or consult the specialists for application advice. Precision feeler gauges – Metav IndustryLine, conical tips, 0.05–1.00 mm The Precision feeler gauges are a ring-mounted set designed for precise gap and clearance measurement in mechanical workshops and toolrooms, suited to engine tuning, valve setting and fine assembly tasks. Conical tips for precise insertion 0.05–1.00 mm measurement range 20 blades on a retention ring Robust 1,000 mm blade length Accurate measurement where small differences matter Manufactured to close tolerances, these feeler blades offer a measurement range from 0.05 to 1.00 mm in finely graduated steps that cover the most common inspection and setup tasks. The set was produced under factory standard ("Werksnorm") and the blades are finished to a manufacturing tolerance of approximately ±0.012 mm, which supports repeatable results when comparing clearances or assembling matching parts. For precision-oriented workshops and maintenance shops this combination of fine gradation and defined tolerance translates into fewer adjustment cycles and a lower risk of assembly error, making the set a pragmatic choice for tasks that require consistent gap control. Organised handling and reliable blade geometry A ring-mounted design keeps the 20 blades accessible and securely retained while enabling quick selection and straightforward storage. The blades feature a conical form, which eases insertion into narrow joints and stepped clearances and reduces the risk of catch or deformation at the tip during measurement. The nominal blade width of 12.7 mm provides a stable contact surface that helps avoid flex in thin gaps, and the long blade option—listed at 1,000 mm—offers reach for larger components or specialised fixtures without compromising handling. Together these details reduce downtime searching for the right thickness and help maintain consistent contact conditions during repeated checks. Typical applications and practical advantages in the workshop This ring-mounted gauge set is tailored for precision fitting, setting valve clearances, checking bearing play and selecting shims during assembly. The fine increment steps—ranging from 0.05 mm upward in defined stages—allow close approach to a target clearance and make progressive adjustments straightforward. The robust retention system and conical tips also suit use in confined or stepped bore situations where a rigid feeler profile is required for reliable feedback. For procurement and maintenance managers the set represents a useful blend of organisation, measurable accuracy and practical ergonomics that support standardised procedures across multiple operators. Contact Metav Werkzeuge today for application advice or to request the Metav IndustryLine set M318.020.5 and ensure the right blade range for workshop requirements; phone +49 2822 7131930 or e‑mail info@metav-werkzeuge.com Technical data Article number: M318.020.5 GTIN: 4054469162737 Customs tariff no.: 90173000 Core technical data Length: 1,000 mm Measurement range: 0.05–1.00 mm Thickness steps: 0.05 / 0.10 / 0.15 / 0.20 / 0.25 / 0.30 / 0.35 / 0.40 / 0.45 / 0.50 / 0.55 / 0.60 / 0.65 / 0.70 / 0.75 / 0.80 / 0.85 / 0.90 / 0.95 / 1.00 mm Accuracy (manufacturing tolerance): ~±0.012 mm Number of blades per set: 20 Special features Conical blade geometry Retention ring for organised storage Factory standard (Werksnorm) production Ring-mounted set for workshop use FAQ What thicknesses are included in the set? The set comprises thicknesses from 0.05 mm up to 1.00 mm in defined steps, supplied as a 20‑blade ring set (SKU M318.020.5). Are the blades suitable for narrow or stepped gaps? Yes, the conical tips are designed to ease insertion into narrow joints and stepped bores while maintaining reliable contact. Is this product delivered as a complete set? The product is supplied as a 20‑piece set on a retention ring, manufactured to factory standard (Werksnorm). Can this set be used for valve clearance and shim selection? The fine gradation and stable blade width make the set well suited for valve clearances, shim selection and similar precision fitting tasks. Which brand produces this feeler set and what is the article number? This is a Metav IndustryLine product, article number M318.020.5, distributed via Metav Werkzeuge. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
100mm Setting Ring Form C Hardened Gauge Steel DIN 2250, JS 3 - Metav IndustryLine
Take advantage of a hardened and lapped gauge surface together with DIN-certified tolerances for reliable reference measurements; the combination of 100 mm nominal diameter and a substantial 2.3 kg mass delivers stable seating and reproducible setup results. Order directly via Metav Werkzeuge or request advice from our consultants for procurement and specification checks. Setting ring 100 mm (gauge ring) – hardened gauge steel, DIN 2250 JS 3 Setting ring 100 mm for precision setting and verification of internal gauges and measurement equipment in workshops and inspection rooms. Hardened, lapped gauge steel construction DIN 2250 / DIN 286 tolerance JS 3 Diameter 100 mm, Form C geometry Robust 2.3 kg mass for measurement stability Reliable reference for workshop and inspection use The Setting ring 100 mm is engineered as a stable reference for setting and checking internal measuring instruments. With a nominal diameter of 100 mm and compliance with DIN 2250, the ring provides a defined datum that simplifies transfer of dimensional standards across tools and setups. The clear normative specification helps integrate the ring into QA routines where traceable, repeatable references are required. Material and finish that minimise wear and error Manufactured from hardened gauge steel and delivered with a lapped finish, this gauge ring resists surface degradation and preserves form accuracy under frequent handling. The lapping process reduces micro-roughness, which lowers measurement scatter when mating gauges or styli are applied. The material selection and finishing approach therefore reduce long-term maintenance and protect measurement certainty. Norm conformity for traceable tolerances Designed to meet DIN 2250 and DIN 286, with tolerance class JS 3, the ring facilitates documented conformity checks and acceptance testing. These standards define the permissible deviation band, enabling users to rely on the ring as a reference within calibrated inspection chains. Such normative alignment supports quality control regimes and helps to demonstrate process capability during audits. Stable mass and form for reproducible seating At 2.3 kg, the ring offers sufficient mass to avoid displacement during routine handling, improving the repeatability of setting operations. The Form C profile ensures predictable contact geometry when gauging instruments are introduced, reducing operator-induced variation and enhancing the precision of comparative measurements. Practical handling and integration into workflows The ring’s compact size and clearly specified geometry make it straightforward to store and deploy on inspection benches or in gauge sets. The robust construction allows frequent use without rapid wear, and the normative documentation simplifies inventory classification in toolrooms and calibration labs. Use the ring as a primary reference for calibrating internal micrometres, bore gauges and comparative tests. Proven sourcing and suitability for industry use As part of the Metav IndustryLine range the ring is intended for industrial and workshop use where durable, standards-compliant gauge equipment is required. The combination of normative conformity, hardened and lapped material and a stable mass makes this component a pragmatic choice for quality-focused shops and inspection departments that require long-term reproducibility. Contact Metav Werkzeuge for a tailored specification review or procurement of the Metav IndustryLine setting ring (M313.100); telephone +49 2822 7131930 or email info@metav-werkzeuge.com Technical Data SKU: M313.100 GTIN: 4054469121031 Tariff number: 90173000 Facts Diameter: 100 mm Weight: 2.3 kg Special features Material: hardened gauge steel, lapped Norms: DIN 2250 and DIN 286, JS 3 Geometry: Form C FAQ What tolerance class does the ring comply with? The setting ring conforms to DIN 2250 and DIN 286 with tolerance class JS 3, providing a defined deviation range for reference measurements. What material and finish are used for the ring? The ring is made from hardened gauge steel and supplied with a lapped finish, designed to reduce surface wear and improve measurement repeatability. For which applications is this gauge ring intended? This gauge ring is intended for setting and verifying internal measuring instruments such as bore gauges and comparative gauges in workshop and inspection environments. What does Form C indicate for this ring? Form C refers to the geometric form specified in the applicable standards and denotes the ring’s contact and profile characteristics as defined by DIN 2250. What is the product identifier for ordering? The article is listed as M313.100 in the Metav IndustryLine range and carries GTIN 4054469121031 for unambiguous identification. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
105mm Setting Ring Form C Hardened Gauge Steel DIN 2250/DIN 286 JS3 - Metav IndustryLine
Benefit from a hardened, lapped gauge steel construction, DIN 2250 conformity and a precise 105 mm diameter for stable, repeatable setting operations; order the setting ring directly via Metav Werkzeuge or consult our advisers for technical clarification. Setting ring 105 mm — hardened gauge steel, DIN 2250 conformity The Setting ring 105 mm is a precision reference gauge designed for setting and verification tasks in industrial metrology, providing a compact, stable reference for tool presetting and dimensional checks. Hardened, lapped gauge steel Conforms to DIN 2250 / DIN 286 JS 3 Precision 105 mm diameter Robust Form C configuration A stable reference that reduces setup variability The ring is manufactured from hardened and lapped gauge steel, delivering a wear-resistant contact surface that preserves dimensional integrity over many cycles. Conformity to DIN 2250 and DIN 286, JS 3 specifies the geometric and tolerance requirements, making the component a dependable reference for transferring nominal diameters. The compact 105 mm diameter combined with the Form C profile gives a consistent seat and contact geometry, which reduces measurement scatter and supports reproducible tool-setting operations. Designed to support efficient workshop workflows With a mass of 2.3 kg, the part offers intrinsic stability during use, minimising the risk of movement that can distort setting results. The robust construction shortens adjustment times by providing an immediate, repeatable datum; this contributes to higher throughput and fewer reworks in daily production. Where repeatability and quick changeovers matter, the ring functions as a time‑saving reference that integrates directly into existing presetting and inspection routines. Ready for quality-controlled processes and traceable inventory The component carries a GTIN and an eClass identifier for straightforward inventory management and traceability. Compliance with recognised DIN standards simplifies documentation in quality processes and supports compatibility with other calibrated tools. As a workshop-grade setting gauge, the ring is suitable for routine verification, tool presetting and as a reproducible reference within non-accredited measurement chains where mechanical stability and standardised tolerances are required. Choose the Metav IndustryLine setting ring for robust, DIN-compliant reference performance and source it through Metav Werkzeuge for straightforward supply from Emmerich. Technical data Article number: M313.105 GTIN: 4054469121048 Brand: Metav IndustryLine Diameter: 105 mm Weight: 2.3 kg Material: hardened and lapped gauge steel Standards: DIN 2250; DIN 286, JS 3 Facts Diameter: 105 mm Weight: 2.3 kg ECLASS: 21170104 Customs tariff number: 90173000 Special features Form C configuration Hardened and lapped surface Category: Gauges (Lehren) FAQ What is the primary application of this setting ring? The Setting ring 105 mm from Metav IndustryLine serves as a precision reference for setting instruments, verifying diameters and as a reproducible datum in workshop measurement and tool presetting. Which standards govern the tolerances of the ring? Tolerance and form requirements are specified by DIN 2250 and DIN 286, JS 3, which are satisfied by this setting ring. What material and finish are used for durability? The component is made of hardened and lapped gauge steel, providing a wear-resistant surface and long-term dimensional stability. Is the ring suitable for routine workshop use? Yes; the 2.3 kg mass and robust Form C profile make it well suited to repeatable workshop tasks and quick, stable set-up cycles. Can this part be integrated into a calibrated quality system? The ring is manufactured to DIN tolerances and can act as a workshop reference; accredited calibration requirements depend on the quality system and any necessary calibration certificates are not specified in the basic product data. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
10mm Test Pin Single, ±0.001mm Accuracy, Length 50mm, Workshop Version - Metav IndustryLine
Take advantage of precise end‑dimension verification combined with robust workshop construction and consistent repeatability; the 10.00 mm diameter with ±0.001 mm tolerance ensures tight fits and reliable inspection results. Order the gauge pin directly via Metav Werkzeuge or consult the team for application advice. M323.000 Test pin – gauge pin, 10.00 mm, ±0.001 mm (Metav IndustryLine) The M323.000 test pin is a workshop‑grade precision gauge pin intended for end‑dimension checks, fixture alignment and general inspection tasks in industrial metrology. Workshop‑grade precision pin Diameter 10.00 mm with ±0.001 mm tolerance Special steel construction, length 50 mm Consistent dimensional accuracy for inspection The M323.000 is specified for a 10.00 mm nominal diameter with a tight ±0.001 mm deviation, making it suitable where minute dimensional conformity is decisive. Such accuracy reduces uncertainty during go/no‑go assessments and supports faster decision‑making on production lines. The clear numeric specification provides a verifiable basis for tolerance stacks and inspection reports, helping to cut rework and to document compliance with drawing requirements. Robust workshop design for repeated use Constructed from special steel and offered as a workshop‑grade item, the pin combines durability with a manageable 50 mm length that balances reach and stiffness. The chosen material and compact geometry provide resistance to wear in routine use while keeping handling straightforward during fixture insertion. This combination supports long service life under typical workshop conditions and maintains precision across repeated cycles without complex maintenance. Easy integration into inspection and tooling routines As a single‑item gauge pin with a compact profile, the component fits into fixture bores, counter‑gauges and alignment procedures where reliable reference dimensions are required. The clearly defined numeric attributes enable straightforward procurement and inventory coding for quality departments. Metav IndustryLine’s focus on accessible precision ensures that this gauge pin can be adopted across workshops and inspection benches, supporting consistent measurement routines and traceable part verification. Contact Metav Werkzeuge for tailored advice on integrating the M323.000 test pin into existing inspection processes or to request a technical datasheet via info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: M323.000 GTIN: 4061905056017 Brand: Metav IndustryLine Designation: Test pin, single Core data Diameter: 10.00 mm Tolerance: ±0.001 mm Length: 50 mm Weight: 0.033 kg Special features Material: Special steel Workshop version Eclass: 21170231 Packaging: single item FAQ What tolerance does this gauge pin offer? The M323.000 test pin from Metav IndustryLine is specified with a tolerance of ±0.001 mm. What are the physical dimensions of the pin? Diameter 10.00 mm and length 50 mm; weight 0.033 kg are the nominal dimensions for the M323.000 gauge pin. Which material is used for the pin? The M323.000 is manufactured from special steel and designed for repeated workshop use. Where is this gauge pin typically applied? The M323.000 is intended for end‑dimension checks, alignment in fixtures and precision inspection tasks across general metrology and workshop inspection routines. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
10–11mm Gauge Pin Set With Holder 0.01mm Increment, Supplied In Case - Metav IndustryLine
Take advantage of 0.01 mm diameter steps and an accurate ±0.004 mm tolerance in a matched 101-piece range for consistent fit checks; supplied with a pin holder and a transport case for immediate workshop use. Order the gauge pin set directly via Metav Werkzeuge or ask our consultants if needed. Gauge pin set – 10–11 mm range, 0.01 mm increments by Metav IndustryLine Gauge pin set for precision diameter verification and fit checking in quality control, toolmaking and inspection tasks Precise 0.01 mm diameter steps Complete 101-piece matched set Supplied with pin holder and transport case Special steel for dimensional stability Precision that speeds up quality decisions The matched 101-piece set delivers continuous diameter coverage across the 10–11 mm band with 0.01 mm increments, enabling rapid selection of the correct gauge for tolerance checks. With an indicated accuracy of ±0.004 mm, this assortment supports reliable pass/fail assessments and reduces uncertainty during incoming inspection or final control. The fine step size simplifies iterative adjustments on assembly lines and shortens decision cycles in the workshop. Ready-to-use kit for improved workflow efficiency Delivered as a complete kit, the set includes a dedicated pin holder and a protective transport case, so the collection remains organised and ready at the bench. The compact layout of the pins minimises handling time when comparing diameters or performing sequential measurements, which translates into measurable time savings during batch testing. The matched pairings reduce the need for supplemental gauges and speed up traceable inspection procedures. Material choice for stable dimensions over time Manufactured from special steel, the pins are designed for dimensional stability and consistent contact geometry under regular use. The material selection and production tolerances ensure long-term repeatability, which is essential when the same reference pins are used across multiple inspection stations. Clear marking and matched sizing help maintain a documented chain of measurement when integrating the set into quality management systems. Suited to shopfloor inspection and precision workshops This gauge assortment is suitable for fit testing, diameter verification and reference measurements in production and metrology settings. The fine gradation and matched manufacturing minimise interpolation errors when determining the best-fit pin, supporting efficient troubleshooting and setup work. Where repeatability and quick throughput matter, the set provides a practical balance between range and handling convenience. Contact Metav Werkzeuge to secure the Metav IndustryLine gauge pin set, complete with pin holder and transport case, for immediate integration into inspection routines. Technical data SKU: M318.580 GTIN: 4054469156170 Manufacturer: Metav IndustryLine Core data Pieces per set: 101 Diameter range: 10.0–11.0 mm Increment / step: 0.01 mm Accuracy: ±0.004 mm Pin length: 50 mm Weight: 6.6 kg Special features Material: special steel Includes: pin holder Delivery: transport case included Tariff number: 90173000 Set type: matched 101-piece set FAQ What applications are best suited to this gauge pin set? The gauge pin set is ideal for diameter verification, fit testing and component inspection in quality control, toolmaking and workshop calibration tasks. How are the pins delivered and stored? Pins are supplied as a matched 101-piece set, delivered with a pin holder and a protective transport case to keep the collection organised and portable. What is the resolution and typical accuracy of the set? The set has 0.01 mm increments with an indicated accuracy of ±0.004 mm, making it suitable for precise fit checks and repeatable reference measurements. Can these pins be used as reference standards in production? Yes; the matched manufacturing and material choice support repeatability, allowing the pins to serve as convenient reference tools within inspection workflows. Is the material specified for long-term dimensional stability? The pins are made from special steel, chosen to maintain contact geometry and dimensional stability under regular inspection use. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
10–20mm Gauge Pin Set 101 Pieces 0.1mm Increment With Holder, Supplied In Case - Metav IndustryLine
Take advantage of the combination of high measuring accuracy, broad coverage from 10.0–20.0 mm and robust special steel construction for reliable, repeatable inspection workflows. Order the gauge pin set directly via Metav Werkzeuge or ask our consultants if needed Gauge Pin Set M318.524 — 10.0–20.0 mm coverage, 0.1 mm increments (Metav IndustryLine) The Gauge Pin Set M318.524 is a precision inspection set designed for dimensional verification and hole gauging across the 10.0–20.0 mm range, suitable for production control and quality assurance tasks in metalworking and toolmaking Complete 10.0–20.0 mm coverage 0.1 mm increments for fine gradation Manufactured from special steel Faster inspection with reliable step coverage A comprehensive range spanning 10.0–20.0 mm in 0.1 mm increments reduces tool changes and speeds up batch inspection. The graded pins allow quick selection of the nearest nominal diameter, enabling concise go/no-go checks and incremental measurement without recalibration between sizes. For production lines and quality benches, this coverage translates into fewer interruptions and a measurable gain in throughput while maintaining consistent sampling routines. Robust construction for consistent results Made from special steel, the pins resist wear and preserve dimensional integrity under frequent use. The set delivers a stated measuring deviation of 0.004 mm, which supports tight tolerances in workshop and inspection environments. The material choice and finish ensure a stable contact surface that minimises measurement scatter; combined with correct handling, this contributes to reproducible readings and extended service life for the tools. Practical handling and integration into the workshop Designed as an inspection set rather than single-use gauges, the pins are complemented by a dedicated pin holder, easing handling and alignment during hole checks. The set’s mass and balance allow steady manual operation during repetitive inspections; the straightforward incremental system also fits into existing inspection routines and documentation workflows. For procurement, Metav IndustryLine supplies this set as a ready-to-use package for immediate inclusion in quality-control procedures. Contact Metav Werkzeuge for tailored advice on how the Metav IndustryLine gauge pin set can be integrated into inspection processes and to confirm suitability for specific production tolerances Technical Data Article number: M318.524 GTIN: 4054469156279 Tariff number: 90173000 Weight: 5.6 kg Material: Special steel Facts Measuring range: 10.0–20.0 mm Graduations: 0.1 mm Measuring deviation: 0.004 mm Pack format: set Special features With pin holder Set for incremental gauging ECLASS: 21170231 FAQ What measurement range does the set cover? The set covers the 10.0–20.0 mm range with 0.1 mm increments to allow fine-grained dimensional checks. How precise are the pins for routine inspection? The pins achieve a measuring deviation of 0.004 mm, making the Gauge Pin Set M318.524 (Metav IndustryLine) suitable for close-tolerance checks in metalworking. What material are the pins made from and why does that matter? Pins are manufactured from special steel, which provides wear resistance and consistent contact surfaces to maintain dimensional stability during repeated use. Is the set suitable for production line sampling? Yes — the graduated coverage and robust construction are intended for repeated sampling and quick go/no-go verification within routine production inspection. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
11 mm Gauge Ball Pair Hardened Chrome Steel 0.003 mm Accuracy, Diameter Tolerance 0.00008 mm - Metav IndustryLine
Optimise reference and calibration routines with a hardened chrome‑steel gauge ball pair offering an 11 mm diameter and 0.003 mm accuracy; the combination of tight diameter tolerance and high surface quality delivers reproducible datum points for fixtures and inspection jigs. Order directly via Metav Werkzeuge or ask our consultants for application guidance. Gauge ball pair M318.421 – 11 mm, 0.003 mm accuracy (Metav IndustryLine) A gauge ball pair M318.421 designed as high‑precision reference spheres for metrology, go/no‑go gauges and fixture alignment in inspection and workshop environments Hardened chrome‑steel gauge balls 11 mm nominal diameter Accuracy 0.003 mm Diameter tolerance 0.00008 mm Precision that reduces measurement uncertainty The pair of hardened chrome‑steel spheres provides repeatable reference points for aligning fixtures, checking runout and calibrating contact probes. With an stated accuracy of 0.003 mm and a diameter tolerance of 0.00008 mm, the parts are suitable where reproducibility matters. The very low surface roughness (0.00001 mm) minimises contact variation and friction, helping to maintain consistent probe responses and reducing the need for repeat measurements. These characteristics support faster inspection cycles and more predictable quality control. Robust material and finish for stable performance Made from hardened chrome steel (>HRC 62), the spheres resist deformation and wear even under repeated contact measuring. The material choice and hardening ensure that the nominal 11 mm diameter remains stable over time, which is essential for reference artefacts used in fixtures and gauges. Delivered as a set of two, the pair is suitable for establishing datum lines or paired support points. The construction and finish minimise the influence of handling and environmental factors, so calibration intervals can focus on process‑critical instruments rather than consumable reference parts. Practical benefits for workshop and inspection use The compact size and high accuracy make these balls a convenient addition to calibration kits and inspection benches. Their geometry allows precise contact with probes and feeler‑type instruments, enabling quick checks without complex setup. Where throughput is important, the consistent contact behaviour translates into fewer reworks and more reliable part acceptance. For applications that require traceable reference artefacts, the clear specification of diameter, tolerance and hardness provides an objective basis for measurement procedures and documentation. Contact Metav Werkzeuge today to discuss how the Metav IndustryLine gauge ball pair can streamline inspection workflows; our technical team at info@metav-werkzeuge.com or +49 2822 7131930 will advise on integration and supply Technical Data SKU: M318.421 GTIN: 4054469184098 Material: Chrome steel, hardened Diameter: 11 mm Accuracy: 0.003 mm Set: contains 2 pieces Facts Weight: 0.05 kg Diameter tolerance: 0.00008 mm Surface roughness: 0.00001 mm Hardness: >HRC 62 Pieces per set: 2 Special features Category: Gauges (reference spheres) Finish: high‑precision surface Intended use: reference points, fixture alignment, calibration FAQ What is the intended use for these gauge balls? The gauge ball pair M318.421 is intended as high‑precision reference spheres for fixtures, gauge blocks, probe calibration and alignment tasks in inspection and workshop environments. How precise are the spheres and what tolerance applies? The spheres have an accuracy of 0.003 mm with a diameter tolerance of 0.00008 mm, making them suitable for reproducible reference measurements and precise datum definition. What material and hardness are specified for these balls? The balls are manufactured from hardened chrome steel with a hardness greater than HRC 62, providing wear resistance and dimensional stability for repeated contact measures. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
11 mm Gauge Pin Wear Allowance, Hardened Steel, DIN 7162 - Filetta
Reliable 11 mm limit plug gauge manufactured from hardened steel and produced to DIN 7162 ensures consistent go/no‑go inspection and predictable wear behaviour; order directly via Metav Werkzeuge or consult our specialists for application advice. Limit plug gauge MS911.215 — Filetta, 11 mm, hardened steel (DIN 7162) The Limit plug gauge MS911.215 is a precision inspection pin for go/no‑go checks of internal diameters in production and quality control environments. Hardened steel for long service life DIN 7162 standard compliance 11 mm nominal diameter for bore checks Wear allowance on good side Consistent inspection backed by an industry standard This gauge pin delivers reliable, repeatable checks for internal bores, designed to support standardised quality workflows. Manufactured in accordance with DIN 7162, the tool provides a clear reference for pass/fail decisions and integrates readily into established inspection sequences. The 11 mm nominal dimension is presented as a precise measuring reference, and the geometry of the pin minimises wobble during insertion to improve repeatability and reduce measurement scatter in serial inspection. Robust construction for long operational life Made from hardened steel, the pin resists surface damage and maintains its working diameter under frequent use. The design incorporates a wear allowance on the good side, which signals gradual material loss without compromising the functional check; this feature extends usable life while making wear visible during routine inspections. For workshops that demand low downtime, the material choice and finish reduce the need for frequent replacement and support uninterrupted production checks. Practical application and handling in the workshop The plug gauge is intended for quick go/no‑go checks on internal diameters in machining, assembly and incoming inspection stations. Its compact form enables fast handling and clear pass/fail interpretation, supporting efficient throughput without complex procedures. Markings and standard conformity simplify traceability and documentation, while the sturdy construction keeps maintenance straightforward and predictable. The Filetta badge denotes established toolmaking expertise and suitability for industrial environments where dependable gaging is required. For application-specific advice on using this Filetta limit plug gauge and to obtain supply directly from Metav Werkzeuge in Emmerich, contact our team for tailored recommendations and fast delivery Technical data Article number: MS911.215 Manufacturer: Filetta Material: hardened steel Facts Nominal diameter: 11 mm Special features DIN 7162 compliant Wear allowance on good side Application: internal bore go/no‑go inspection Category: gauge pins / plug gauges FAQ What is the primary application of this gauge? The Filetta limit plug gauge MS911.215 is intended for go/no‑go inspection of internal diameters during production and quality control. What does the wear allowance on the good side mean? The wear allowance indicates a deliberate tolerance on the pass side so that gradual surface wear can be detected without immediately affecting the go/no‑go result, extending usable life. Is this gauge compliant with recognised standards? Yes, the plug gauge is manufactured in accordance with DIN 7162, which governs limit gauge design and marking. What is the exact nominal size of the pin? The nominal diameter is 11 mm; reference and tolerance interpretation follow DIN 7162 specifications. Which workshop environments are suitable for this tool? The gauge is suited to machining, assembly and incoming inspection where compact, rapid internal diameter checks are required; its hardened steel construction supports frequent use. Manufacturer / Responsible: Schut Geometrische Meettechniek bv; Duinkerkenstraat 21; 9723 BN Groningen; The Netherlands; +31 50 5877877; schutnl@schut.com
11 mm Limit Plug Gauge Wear Allowance On Good Side, DIN 7162 - Filetta
Take advantage of precise, fast pass/fail checks and robust wear resistance thanks to hardened steel and DIN 7162 conformity; order the matching gauge pins directly via Metav Werkzeuge or contact our consultants for batch and inspection advice. Limit Gauge Pin — hardened-steel inspection pin, 11 mm, DIN 7162 (Filetta) The Limit Gauge Pin is a hardened-steel inspection pin designed for rapid go/no-go checks and routine dimensional control in workshops and inspection benches, compliant with DIN 7162. Hardened-steel construction for long service life Conforms to DIN 7162 for consistent tolerances 11 mm nominal diameter for standard inspection tasks Wear allowance on the good side to extend usable life Faster, reliable pass/fail inspection for production lines The compact inspection pin delivers quick go/no-go checks that reduce measuring time at control points and on the shop floor. By providing an unequivocal pass or fail condition, the pin supports efficient decision-making in both single-piece inspections and repetitive sampling routines. Conformity with DIN 7162 ensures that the nominal diameter and tolerance band are traceable to an established standard, which simplifies integration into existing inspection protocols and statistical process control. Robust build that minimises downtime Thanks to its hardened steel construction the pin withstands repeated contact without rapid degradation, while the specified wear allowance on the good side preserves the functional limit for longer. This translates into fewer replacements, reduced downtime and lower indirect costs from inspection interruptions. The hardened surface also keeps seating and mating surfaces consistent, helping to avoid false rejects that would otherwise increase rework. Practical benefits for inspection benches and gauge sets As a dedicated inspection pin, the component is optimised for quick handling and straightforward verification tasks on inspection benches and assembly jigs. The clear go/no-go characteristic reduces interpretation time for operators and speeds up routine quality checks. For quality managers the result is measurable: quicker throughput at control stations and a more consistent acceptance rate across batches. Traceability and suitability for regular quality workflows Manufactured to industry standard, the pin supports consistent batch-to-batch performance and straightforward inventory management when used in gauge sets or fixed inspection fixtures. The simple geometry and standardised tolerance regime make the item suitable for assembly audits, incoming inspections and periodic verification of tool wear, providing procurement confidence for maintenance and quality teams. Request technical advice or a batch availability check from Metav Werkzeuge in Emmerich to align delivery options with production schedules Technical Data Article number: MS911.173 Name: Limit Gauge Pin Material: hardened steel Standard: DIN 7162 Measurements / Core data Diameter: 11 mm Features / Applications Wear allowance on the good side Hardened for wear resistance Intended for go/no-go inspection tasks Category: gauge pins / inspection pins FAQ What is the nominal diameter of this inspection pin? The inspection pin has a nominal diameter of 11 mm; this specification applies to the Filetta limit gauge pin (SKU MS911.173). Is the pin suitable for go/no-go checks on assembly lines? Yes, the Filetta limit gauge pin is designed for rapid pass/fail checks and is suitable for routine assembly-line and workshop inspections. What material is used and how does it affect service life? The pin is made from hardened steel, which increases wear resistance and extends usable life compared with untreated pins. Which standard governs the pin’s tolerances? Tolerances and dimensions conform to DIN 7162, providing a recognised reference for inspection procedures. How does the wear allowance on the good side affect inspection practice? The specified wear allowance on the good side allows continued use while preserving the functional limit for a longer period, reducing unnecessary replacements Manufacturer / Responsible: Schut Geometrische Meettechniek bv; Duinkerkenstraat 21; 9723 BN Groningen; The Netherlands; +31 50 5877877; schutnl@schut.com
11,19mm Prüfstift, Länge 50 mm, Werkstatt-Ausführung, Spezial‑Stahl, mit Kiste - Metav IndustryLine
Der präzise Prüfpartner für Werkstatt und Fertigung: Nutzen Sie die Kombination aus hoher Genauigkeit, robustem Spezial‑Stahl und sicherer Transportverpackung für verlässliche Endmaßkontrollen. Bestellen Sie den Prüfstift direkt über Metav Werkzeuge oder fordern Sie technische Beratung an. Prüfstift, einzeln, 11,19 mm Länge 50 mm von Metav IndustryLine Der Prüfstift, einzeln, 11,19 mm Länge 50 mm ist ein präziser Messstift für Endmaß‑Kontrollen und Werkstattprüfungen, konzipiert für wiederholgenaue Maßprüfungen bei Montagen und Serienkontrollen. Werkstatt-Ausführung für robuste Einsätze Spezial‑Stahl für hohe Verschleißfestigkeit Präzision ±0,002 mm für Endmaßkontrollen Länge 50 mm für einfache Handhabung Lieferung in robustem Kasten für Transport Robuste Werkstoffwahl sichert Langzeitpräzision Der Prüfstift wird aus Spezial‑Stahl gefertigt, was Verschleißfestigkeit und Formstabilität kombiniert. Dank dieses Materials bleibt die Messfläche auch bei häufigem Einsatz dauerhaft erhalten, wodurch sich Stillstandszeiten für Nacharbeit verringern. Die Werkstatt‑Ausführung ist auf rauere Umgebungen ausgelegt, sodass der Prüfstift auch bei wiederholten Montagevorgängen seine Maßhaltigkeit bewahrt und konstante Prüfergebnisse liefert. Hohe Genauigkeit für zuverlässige Endmaßprüfungen Mit einer ausgewiesenen Genauigkeit ±0,002 mm eignet sich der Prüfstift gezielt für Endmaßkontrollen und Abgleichmessungen. Die kleine Messgröße ermöglicht präzise Passungsprüfungen und Maßvergleiche bei Bauteilen mit engen Toleranzen. Anwender profitieren von reproduzierbaren Ergebnissen, weil die Konstruktion verwindungsarm ist und die Schaftlänge von 50 mm eine ergonomische Handhabung erlaubt. Vielseitiger Einsatz in Fertigung und Qualitätssicherung Dieses Messmittel richtet sich an Anwender in der Fertigungsmesstechnik, im Maschinenbau und in der Serienmontage, die kompakte und belastbare Prüfinstrumente benötigen. Typische Anwendungen sind Passungsprüfungen, Prüflehren‑Ergänzungen und Stichprobenkontrollen in Produktionslinien. Durch die kompakte Bauform eignet sich der Prüfstift auch für enge Messpunkte und Innenbearbeitungsstationen. Sichere Lieferung und dokumentierte Identität Der Prüfstift wird transportgerecht in einem robusten Kasten geliefert, der Beschädigungen beim Versand reduziert und die Handhabung beim Transport erleichtert. Die Kennzeichnung mit SKU M323.B19 und GTIN 4061905064951 sorgt für nachvollziehbare Bestell- und Lagerprozesse; das übersichtliche Gewicht von 0,1 kg erleichtert die Logistikplanung. Für präzise Endmaß‑Kontrollen empfehlen wir den Prüfstift M323.B19 von Metav IndustryLine – technische Beratung und Bestellung über Metav Werkzeuge, eMail: info@metav-werkzeuge.com oder Telefon: +49 2822 7131930 Produktmerkmale Bezeichnung: Prüfstift, einzeln, 11,19 mm Länge 50 mm Artikelnummer: M323.B19 Marke: Metav IndustryLine GTIN: 4061905064951 Daten Länge: 50 mm Messbereich: 11,19 mm Gewicht: 0,1 kg Genauigkeit: ±0,002 mm Besonderheiten Werkstatt-Ausführung Material: Spezial-Stahl Kategorie: Messstifte Verpackung: Lieferung in Kasten FAQ Wie genau ist der Prüfstift im praktischen Einsatz? Der Prüfstift M323.B19 von Metav IndustryLine weist eine Genauigkeit von ±0,002 mm auf, was ihn für Endmaßkontrollen und Passungsprüfungen mit engen Toleranzen auszeichnet. Für welche Anwendungen eignet sich der Prüfstift besonders? Das Messstift‑Format ist ideal für Passungsprüfungen, Stichprobenkontrollen und den Einsatz in der Serienmontage, wo kompakte, verschleißfeste Prüfmittel benötigt werden. Aus welchem Material besteht der Prüfstift und welche Vorteile bringt das? Der Prüfstift besteht aus Spezial‑Stahl; dies bietet hohe Verschleißfestigkeit und Formstabilität, wodurch die Messflächen auch bei häufigem Einsatz dauerhaft zuverlässig bleiben. Wie wird der Prüfstift geliefert und wie erleichtert das die Handhabung? Der Prüfstift wird transportgerecht in einem robusten Kasten geliefert, der Beschädigungen beim Versand minimiert und den sicheren Transport zum Einsatzort gewährleistet. Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
11-12mm Test Pin Set 101 Pieces 0.01mm Increment With Probe Holder In Case - Metav IndustryLine
A compact inspection kit that combines fine increments with workshop robustness: 101-piece gauge pin set with 0.01 mm increments and an assessed accuracy of ±0.004 mm, supplied with a gauge pin holder and protective case. Order the set directly via Metav Werkzeuge or consult our specialists for application guidance. Gauge pin set — 101-piece, 11–12 mm range, 0.01 mm increments (Metav IndustryLine) The gauge pin set is a workshop-grade inspection kit intended for precise hole and gauge checks in mechanical and maintenance environments. 101-piece set with 0.01 mm steps High tolerance accuracy ±0.004 mm Supplied with a gauge pin holder Delivered in protective transport case Precision where measurement matters The set provides a dense gradation with 0.01 mm increments, enabling fine-tuned selection for go/no-go checks and incremental fit control. With an assessed accuracy of ±0.004 mm, the kit supports tasks that require reliable repeatability in assembly inspection and quality control. The close spacing of the pins reduces adjustment time compared with coarser sets and helps maintain consistent tolerances across batches. The benefit for the workshop is reduced rework and faster verification during setup and incoming inspections, supported by the set's clear labelling and organised layout. Designed for workshop routine and durability Manufactured from special steel, the pins resist wear and preserve dimensional integrity under frequent use. The set comprises 101 pieces, each with a nominal length of 50 mm, packed in a robust transport case that keeps the pins protected and organised between uses. The inclusion of a gauge pin holder simplifies handling during measurement, improving ergonomics and reducing the risk of accidental damage. For workshops that perform repetitive checks, the combination of material choice and protective packaging delivers longer service life and predictable behaviour under daily operational stress. Practical handling and inspection workflow Organisation and speed are central to efficient inspection. The tight incrementing and full set range between 11.00 and 12.00 mm allow immediate selection of the best-fitting pin, eliminating guesswork. Labelling and a clear layout speed up the measurement cycle, while the holder enables safer transfer of pins to fixtures or measuring benches. The set's overall weight of 7.3 kg reflects a complete kit ready for bench or mobile use; the protective case simplifies transport within production areas. This pragmatic combination of features supports shorter cycle times and consistent quality documentation. Contact Metav Werkzeuge for tailored advice on integrating the Metav IndustryLine gauge pin set into existing inspection routines and secure this workshop-ready kit with holder and protective case Technical data SKU: M318.581 GTIN: 4054469156187 Tariff code: 90173000 Facts Measurement range: 11.00–12.00 mm Increment: 0.01 mm Assessed accuracy: 0.004 mm Pieces per set: 101 Length (nominal): 50 mm Weight: 7.3 kg Special features Material: special steel Supplied with a gauge pin holder Delivered in a protective transport case Workshop version, organised layout for fast selection FAQ What tolerance and resolution can be expected from this gauge pin set? The gauge pin set delivers a step size of 0.01 mm with an assessed accuracy of ±0.004 mm, suitable for precise fit and clearance checks. Is the set complete for the stated measurement range? Yes, the 101-piece set covers the range from 11.00 mm to 12.00 mm in 0.01 mm steps and is supplied as a complete workshop kit. What material are the pins made from and how durable are they? Pins are manufactured from special steel, chosen for wear resistance and dimensional stability under frequent use. Does the delivery include any handling aids? The set is supplied with a gauge pin holder and a protective transport case to support safer handling and organised storage. Which SKU identifies this product for ordering? This product is listed under SKU M318.581 within the Metav IndustryLine range. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
11.01mm Test Pin 50mm Length Workshop Version - Metav IndustryLine
This precision test pin delivers repeatable reference measurements thanks to its 11.01 mm diameter, 50 mm length and a tight ±0.002 mm tolerance; its workshop‑grade construction and transport box ensure protected handling and long service life. Order the item directly via Metav Werkzeuge or consult the technical team for application advice. Gauge pin M323.B01 – 11.01 mm diameter, 50 mm length (Metav IndustryLine) The gauge pin M323.B01 is a single precision test pin intended for dimensional checks and end‑measure references in workshop and inspection settings. Single gauge pin Ø 11.01 mm, length 50 mm Tolerance ±0.002 mm for high precision Made from special steel for durability Supplied in transport box, workshop version Exact reference measurements with industrial precision A compact reference element designed for repeatable inspection tasks, the gauge pin provides a reliable datum for go/no‑go checks and verification of end dimensions. The ±0.002 mm tolerance reduces measurement uncertainty and supports fast quality assessments on the shop floor, enabling confident decisions during incoming inspection or final control. As a solid, single‑piece pin, it serves as a stable contact for comparison measurements and simple fixture checks without the need for elaborate apparatus. Robust workshop design for everyday handling Built in a workshop version for practical use, the pin is manufactured from special steel to resist wear during repeated insertions and contact. The 50 mm length offers a good balance between reach and stiffness, while the compact diameter maintains contact integrity in small bores and against flat references. Supplied in a protective transport box, the component arrives ready for safe storage and transfer between benches, reducing the risk of damage that could affect dimensional stability. Practical integration into inspection routines The item functions well as a reference in fixture set‑up, end‑measure verification and comparative gauging. Its compact mass and clear dimensional specification facilitate quick incorporation into measuring jigs or simple test rigs for batch control. Traceability is supported via the listed identifiers, allowing clear inventory and auditability within a quality system. For operations that require regular, reproducible checks, the pin helps keep process tolerances tight and inspection throughput efficient. For application advice, ordering or to confirm compatibility with an existing inspection setup, contact Metav Werkzeuge in Emmerich — Metav’s specialists will advise on lead times and delivery options. Technical data Article number: M323.B01 GTIN: 4061905065613 Label: Prüfstift, einzeln, 11,01 mm Länge 50 mm Numbers / Core technical data Diameter: 11.01 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.1 kg Special features / Versions Material: Special steel Version: Workshop execution Supply: Delivered in a transport box Single item (not in sets) Category: Gauge pins FAQ Is this gauge pin suitable for precision hole checks? The gauge pin M323.B01 is intended for dimensional reference and is suitable for many precision hole checks where a fixed‑diameter probe is applicable. What accuracy can be expected from this test pin? The product is specified with a tolerance of ±0.002 mm, which establishes its suitability for fine inspection tasks requiring high repeatability. What material is used for the pin? This gauge pin is made from special steel, chosen for wear resistance and durability in routine workshop use. Is the pin supplied ready for transport and storage? Yes, the M323.B01 is supplied in a transport box as part of the workshop execution to protect the pin during handling and storage. Can the gauge pin be integrated into existing fixtures? The compact form and standard dimensions allow the pin to be used in simple fixtures and jigs for comparative or end‑measure tasks. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
11.02mm Gauge Pin 50mm Length Workshop Version - Metav IndustryLine
Take advantage of precise dimensional control and robust workshop design to shorten inspection cycles and reduce rework; the combination of ±0.002 mm tolerance and special steel construction ensures reliable repeatability for end‑measure checks — order through Metav Werkzeuge or consult our specialists for tailored supply. Gage pin M323.B02 — 11.02 mm diameter, 50 mm length (Metav IndustryLine) Gage pin M323.B02 is a single inspection pin for dimensional verification and end‑measure checks in workshop and production settings. High-precision tolerance ±0.002 mm Solid special-steel construction Workshop version for robust use Diameter 11.02 mm, length 50 mm Reproducible checks with sub‑millimetre certainty The single inspection pin is manufactured to a tight ±0.002 mm tolerance, making it suitable for precise go/no‑go checks and pass/fail verifications where repeatability is essential. The small diameter of 11.02 mm combined with a stable 50 mm shank delivers a compact measurement reference that minimises deflection and contact error during routine checks. This level of reproducibility reduces inspection uncertainty, shortens setup time and lowers the risk of costly rework in small‑batch production or final inspection processes. Durable construction built for workshop routines Designed as a workshop version, the pin is made from special steel to resist wear under frequent contact and handling. The single‑piece design and compact mass (approx. 0.1 kg) aid comfortable handling and rapid placement in fixtures or jigs, while the material choice maintains geometric integrity over repeated use. For operators this translates into fewer replacements, stable results across many cycles and dependable surface condition for tactile or optical comparison methods. Practical identification and traceable use in production Marked and identified for shop‑floor use, the pin carries clear article references for inventory and quality‑assurance tracking. The compact format suits integration into fixture sets or portable inspection kits and supports fast exchanges during inline checks. With its straightforward geometry, the gage pin is compatible with standard locating bores and simple comparison setups, offering an economical means to enforce dimensional tolerances without complex equipment. For procurement and traceability, refer to M323.B02 and the Metav IndustryLine designation when specifying replacements. For workshop-grade dimensional checks, specify the Metav IndustryLine gage pin M323.B02 via Metav Werkzeuge GmbH in Emmerich — contact our team at info@metav-werkzeuge.com or +49 2822 7131930 for advice and reliable supply Technical data Article number: M323.B02 GTIN: 4061905065620 Brand: Metav IndustryLine SKU: M323.B02 Core specifications Diameter: 11.02 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.1 kg Special features Material: Special steel Version: Workshop execution Type: Single gage pin Category: Messstifte FAQ What tolerance does this inspection pin offer? The gage pin M323.B02 is specified with a tolerance of ±0.002 mm, suitable for precise dimensional checks. Which material is used for the pin? The pin is manufactured from special steel, selected for wear resistance and dimensional stability. Is this pin suitable for use in a workshop environment? Yes, the workshop execution is intended for regular shop‑floor use and frequent handling. How is the product identified for ordering and traceability? Identification is by article number M323.B02 and GTIN 4061905065620 for inventory and procurement. Can this pin be incorporated into simple fixture checks? The single‑piece geometry and compact dimensions make it well suited to locating bores and basic fixture setups for inline inspection. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
11.03mm Gauge Pin 50mm Length Workshop Version - Metav IndustryLine
Take advantage of exact dimensional control provided by the tight ±0.002 mm tolerance and the wear‑resistant special steel construction for consistent inspection results; order the gauge pin directly via Metav Werkzeuge or consult our specialists for application advice. Metav IndustryLine gauge pin — 11.03 mm diameter, 50 mm length A precision gaging pin designed for workshop inspection and fine mechanical end‑measurements, the gauge pin serves as a reliable reference for go/no‑go checks and fit verification. Diameter 11.03 mm for precise fits 50 mm overall length for stable handling Special steel construction for durability Workshop execution for routine inspection Accurate fits for repeatable inspection results The gauge pin is manufactured to a nominal diameter of 11.03 mm with a certified radial tolerance of ±0.002 mm, providing a stable reference for size verification and assembly checks. This level of precision supports rapid go/no‑go decisions on the shop floor and reduces the risk of faulty assemblies, ensuring that downstream processes run without interruption. The compact dimensions suit repetitive tasks where speed and repeatability matter most. Robust material and workshop design that endures daily use Constructed from special steel, the inspection pin is built to withstand regular handling in a production environment. The workshop version balances machinability and surface integrity, delivering a reliable contact surface for gauge blocks, pin jigs and bench fixtures. The modest mass aids ergonomic handling while maintaining sufficient stiffness for short‑run checks and bench inspection routines. Easier handling, quicker quality decisions With a 50 mm overall length the pin offers a comfortable gripping zone without compromising measurement stability. The design simplifies placement into fixtures or receiver holes, speeding up comparative checks and visual go/no‑go assessments. Tight manufacturing tolerances translate into fewer ambiguous results, which shortens inspection time and reduces rework rates across quality control steps. Designed for fine mechanical and small‑part inspection Classified within the micro range of inspection tools, this pin is particularly suited to fine mechanical work and small‑part verification where compact gauges are required. The combination of small nominal diameter and exact tolerance makes it a fitting tool for precision workshops, component manufacturers and calibration benches that demand trustworthy reference gauges. Choose the Metav IndustryLine gauge pin for dependable end‑of‑line checks and contact Metav Werkzeuge GmbH in Emmerich for tailored product guidance at info@metav-werkzeuge.com or +49 2822 7131930 Technical Data SKU: M323.B03 GTIN: 4061905065637 Brand: Metav IndustryLine Label: Gauge pin, single, 11.03 mm diameter, 50 mm length Facts Diameter: 11.03 mm Length: 50 mm Weight: 0.1 kg Tolerance: ±0.002 mm Special features Material: Special steel Workshop execution Category: Gauge pins FAQ What tolerance does the gauge pin have? The gauge pin is produced with a tolerance of ±0.002 mm, delivering the dimensional reliability expected from the Metav IndustryLine M323.B03 inspection pin. For which applications is this gauge pin suitable? The pin is optimised for workshop inspection and fine mechanical end‑measurements where compact, high‑precision reference gauges are required. What is the nominal diameter and length of the pin? The nominal diameter is 11.03 mm and the overall length is 50 mm, dimensions intended for stable handling and precise fit checks. Which material is used for the pin? The inspection pin is made from special steel that is selected for durability and consistent contact performance in routine inspection tasks. How is the product identified for ordering or traceability? Order or reference the item by SKU M323.B03 or GTIN 4061905065637 to ensure the correct Metav IndustryLine gauge pin is supplied. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
11.04mm Gauge Pin 50mm Length Workshop Finish - Metav IndustryLine
Reliable workshop measuring pin in hardened special steel with industrial tolerance and compact length; ideal for confined-space end‑measure checks and inline plug gauging. Order the (gauge pin M323.B04) directly via (Metav Werkzeuge) or ask our consultants if needed. Gauge pin M323.B04 — single gauge pin, Ø 11.04 mm, 50 mm length | Metav IndustryLine The gauge pin M323.B04 is a workshop‑grade measuring pin designed for precise end‑measure checks and plug gauging in production and inspection environments. Precise diameter Ø 11.04 mm Compact 50 mm length for tight spaces Tight tolerance ±0.002 mm for repeatable checks Workshop-grade special steel construction Compact precision for routine end‑measure checks This workshop‑grade measuring pin offers a nominal Ø 11.04 mm with a compact 50 mm length, giving reliable access to bores and confined features without sacrificing rigidity. Manufactured to a tight ±0.002 mm tolerance, the pin supports consistent go/no‑go and comparative checks on the shop floor; the stated accuracy means measurable deviations are kept within a few micrometres, which is sufficient for serial inspection tasks and setting reference gauges. The use of special steel ensures a stable contact surface that withstands repeated engagement while maintaining dimensional integrity. Consistent performance that reduces rework Made in a workshop‑grade execution, the component delivers the kind of precision needed where throughput and quality control meet. The nominal tolerance and robust material selection lower the risk of false rejects and minimise rework, contributing to smoother production flow and predictable inspection intervals. The item’s balanced mass and finish make it easy to seat in fixtures and retainers, so measurement time per part is reduced and process capability is improved without complex fixturing. Practical handling and compatibility in everyday inspection As a single gauge pin, M323.B04 integrates easily into standard plug gauge sets, fixture checks and assembly controls; its compact format suits repetitive manual checks and semi‑automated stations alike. The labeled SKU and GTIN allow straightforward inventory tracking and traceability in procurement systems, while the straightforward geometry keeps cleaning and inspection simple between cycles. Combined with Metav’s quality filter and parts selection, this component supports reliable end‑measure verification across workshops and small production lines. For workshop applications requiring compact, high‑repeatability plug gauging, choose the Metav IndustryLine gauge pin M323.B04 and contact Metav Werkzeuge for ordering or technical clarification at info@metav-werkzeuge.com or by phone on +49 2822 7131930 Technical data Article number: M323.B04 GTIN: 4061905065644 Brand: Metav IndustryLine Measurements Diameter: 11.04 mm Length: 50 mm Tolerance / accuracy: ±0.002 mm Weight: 0.1 kg Materials & features Material: Special steel Workshop execution Single gauge pin Story trigger: end measurements eClass: 21170231 FAQ What applications is this gauge pin suited for? The Metav IndustryLine gauge pin M323.B04 is intended for end‑measure checks, plug gauging and quick comparative inspections on production and inspection benches. How precise is the measuring pin in daily use? With an accuracy of ±0.002 mm the gauge pin provides repeatable measurements suitable for many shop‑floor and assembly verification tasks where micrometre‑level control is required. Can this pin be used in fixture or plug gauge sets? Yes, the single gauge pin M323.B04 is compatible with standard plug‑gauge arrangements and can be mounted in retainers or fixtures for inline checks. What material is the pin made from and how does that affect wear? The pin is manufactured from special steel, offering a durable contact surface that withstands repeated engagement and helps preserve dimensional stability. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
11.05mm Gauge Pin 50mm Length Workshop Version - Metav IndustryLine
Take advantage of a compact, workshop-grade gauge pin with a precise 11.05 mm diameter and tight ±0.002 mm tolerance for repeatable end measurements; its 50 mm length and robust special‑steel construction support reliable everyday inspection. Order the gauge pin directly via Metav Werkzeuge or ask our consultants if needed. Metav IndustryLine Gauge Pin M323.B05 — 11.05 mm diameter, 50 mm length A single gauge pin, designed for precise end and fit checks in inspection, jigs and fixture setups, supplied as an individual unit for straightforward replacement and inventory control. Diameter 11.05 mm precision Length 50 mm compact design Tolerance ±0.002 mm accuracy Special steel, workshop‑grade finish Consistent dimensional control for inspection and assembly The compact gauge pin offers a measurable and dependable reference for go/no‑go checks, end‑of‑line inspections and jig verification. With a nominal diameter of 11.05 mm and a verified tolerance of ±0.002 mm, this inspection pin reduces uncertainty in repetitive checks and supports tighter process control. The short, rigid envelope and straightforward geometry minimise bending and alignment errors, which translates into fewer reworks and improved throughput when used in fixture or gauge stacks. Robust, workshop‑grade design that endures daily use Constructed from special steel, this pin is made for consistent contact and handling in a production environment. The 50 mm length provides sufficient engagement for a stable reference while remaining compact for dense gauge assemblies. The workshop version is finished to withstand frequent insertion and removal; material choice and finish focus on wear resistance and dimensional stability so that replacement intervals are predictable and maintenance costs remain low. The result is a durable tool that maintains its precision across repetitive cycles. Traceability and straightforward integration into quality routines Each unit is identifiable by SKU M323.B05 and GTIN 4061905063008, enabling clear labelling in stores and inspection records. The pin’s simple form factor makes it easy to incorporate into existing gauges, checking fixtures or verification protocols without special adapters. For procurement and planning, the compact size and individual delivery simplify stock management and allow precise replenishment. Add the Metav IndustryLine gauge pin to inspection sets where reproducible dimension references are required for assembly, test benches or incoming‑goods checks. For workshop‑grade precision and reliable supply choose Metav IndustryLine M323.B05 — contact Metav Werkzeuge in Emmerich at +49 2822 7131930 or info@metav-werkzeuge.com for product availability and technical advice Technical data SKU: M323.B05 GTIN: 4061905063008 Brand: Metav IndustryLine Measurements Diameter: 11.05 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.1 kg Special features Material: Special steel Version: Workshop‑grade Delivery: single unit Eclass: 21170231 FAQ Is this gauge pin suitable for use in fixture and jig checks? The Metav IndustryLine gauge pin M323.B05, with an 11.05 mm diameter and ±0.002 mm tolerance, is designed for fixture, jig and assembly‑line checks where a compact, repeatable reference is required. How is the pin supplied and identified for inventory? Each unit is supplied individually and marked by SKU M323.B05 and GTIN 4061905063008 to ease stock control and traceability in inspection systems. What material is used and how does it affect lifespan? The pin is made from special steel; this material choice provides robust wear characteristics suited to workshop environments and frequent handling. Can this gauge pin be used for precision bore checking? Yes — the tight tolerance and precise diameter make the pin suitable as a reference for bore and end measurements when used with appropriate seating and alignment in the inspection set. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
11.06mm Test Pin 50mm Length Workshop Version - Metav IndustryLine
Take advantage of the combination of exact fit, workshop durability and tight tolerance for dependable end‑measure checks; order directly via Metav Werkzeuge or consult the team for application advice. Metav IndustryLine Test Pin — Single gauge pin Ø 11.06 mm, 50 mm length A test pin intended for precise end‑measure verification and fixture checks in mechanical workshops and inspection rigs. Diameter 11.06 mm with ±0.002 mm tolerance 50 mm hardened length for secure engagement Workshop‑grade special steel construction Suited to end‑measure and gauge set applications Accurate end‑measure verification for repeatable checks The pin delivers a diameter of 11.06 mm with a stated tolerance of ±0.002 mm, enabling reliable close‑fit inspections where repeatability matters. Such tight dimensional control reduces uncertainty when verifying bores, dowel fits or mating components; the small tolerance translates directly into fewer sorting steps and reduced rework. The metric dimensioning aligns with common inspection tables and gauge blocks, ensuring the component integrates smoothly into quality procedures. Robust build designed for regular workshop use Manufactured from special steel, the item provides a balance between toughness and wear resistance appropriate for everyday workshop handling. The 50 mm length offers sufficient engagement depth for typical plug‑type checks while remaining manageable in hand or when mounted in a gauge plate. The labelled workshop execution highlights practical design choices such as easy handling and resistance to incidental knocks, which helps maintain functional accuracy over repeated cycles. Simple integration into inspection routines The compact geometry and standard sizing make the pin straightforward to incorporate into existing fixtures and gauge sets. Where precise end‑measure checks are required, the component serves as a stable datum or go/no‑go reference, supporting faster decision making on the shop floor. Clear numeric specification of diameter and tolerance supports process documentation and helps technicians choose the correct reference part without additional measurement steps. For procurement or application guidance on Metav IndustryLine test pins, contact Metav Werkzeuge in Emmerich via info@metav-werkzeuge.com or call +49 2822 7131930 for tailored advice and reliable supply Technical Data Article number: M323.B06 GTIN: 4061905063787 SKU: M323.B06 Facts Diameter: 11.06 mm Tolerance: ±0.002 mm Length: 50 mm Weight: 0.1 kg Special features Material: Special steel Version: Workshop execution Category: Gauge pins Accuracy class: High‑precision tolerance FAQ What applications suit this test pin best? The test pin (Metav IndustryLine single gauge pin, M323.B06) is intended for end‑measure verification, fixture checks and plug‑type inspections in mechanical workshops and inspection rigs. Is the specified tolerance sufficient for precision assembly tasks? Yes, the ±0.002 mm tolerance provided for the Metav IndustryLine test pin supports close‑fit assemblies and accurate verification where tight dimensional control is required. Which material is used and how does it affect durability? The pin is made from special steel; this construction offers workshop resilience and wear resistance suitable for repeated inspection cycles with the Metav IndustryLine gauge pin. Can this pin be used with standard gauge plates and fixtures? The dimensioning (11.06 mm × 50 mm) and metric specification make the pin compatible with common gauge plates and fixture setups used in industrial inspection. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
Fast, tactile checks where electronics are impractical
Gauges and test pins provide unequivocal go/no-go results for threads, bores, gaps and radii without relying on electronics. The range covers plug gauges and ring gauges for internal and external threads, feeler gauges and precision feeler strips for micro‑gap assessment, plus probe pins and measuring pins for tactile diameter and pitch checks.
How these tools work in the production environment
Mechanical gauges operate as direct reference standards: a plug gauge or ring gauge verifies conformity to thread profiles and mating ability, while limit gauges separate accept from reject in a single step. Test pins are used to tactilely measure small bore diameters, centre‑to‑centre distances and radii. Manufactured from hardened gauge steel or ceramic and often precision lapped, these instruments deliver immediate physical results that are ideal for incoming inspection, machine‑side checks and final control.
Measurable benefits that affect production performance
- Reduced scrap and rework through rapid, unambiguous pass/fail assessment.
- Increased repeatability thanks to very low measurement uncertainty and fine lapping.
- Lower downtime: quick checks at the machine save cycle time and reduce setup periods.
- Durable construction with high wear resistance from specialised, low‑distortion alloys.
- Versatile delivery formats: individual gauges, organised sets in wooden cases or metre‑length feeler rolls compliant with DIN 2269.
Why Metav is the practical choice for precision supplies
Metav combines decades of expertise with a broad warehouse and quality filtering from Emmerich. As a precision partner for industry, craft and trade, Metav supplies a comprehensive selection of gauges and test pins alongside complementary tools such as precision calipers and setting rings. With over 48,000 customers and a catalogue exceeding 250,000 items, Metav is positioned to supply reliably, reduce vendor complexity and support traceable quality control to national standards.
Summary
Gauges and test pins are indispensable for dependable, repeatable quality assurance where tactile, mechanical verification is preferred. Choose these plug gauges, ring gauges, feeler strips and probe pins when immediate, robust measurement decisions are required on the shop floor.
FAQ
What materials are gauges and test pins typically made from?
Gauges and test pins are usually manufactured from hardened gauge steel for durability and wear resistance; ceramic variants are available where thermal stability and minimal wear are critical.
How do thread gauges ensure mating capability?
Thread plug gauges and ring gauges check flank diameters and thread form against standards, providing a clear go/no‑go verdict that confirms pairability with mating parts.
Which tolerance class should I choose for probe pins and gauge sets?
Select tolerance classes aligned with your inspection requirements; for high‑precision tasks, sets produced to DIN 2269 or equivalent tolerance classes ensure micrometre‑level control and repeatability.
Can feeler gauges measure contact gaps in valve and engine work reliably?
Yes. Feeler gauges and precision feeler strips, supplied either as a fan or metre‑length rolls, allow accurate assessment of valve clearances and contact gaps down to micrometre increments.
How do limit gauges speed up in‑process inspection?
Limit gauges separate good from bad in a single, tactile operation, enabling rapid go/no‑go checks at the machine and reducing both inspection time and the likelihood of human interpretation errors.
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com