Precision gauge blocks and plug gauges for reliable dimensional control
Mechanical gauge blocks and plug gauges are essential for tactile verification of threads, bores and gap dimensions, providing fast, unambiguous go/no-go results that enhance process reliability and reduce scrap. Designed for industrial metalworking and toolmaking, these precision tools support incoming inspection and final quality checks by delivering traceable measurements in applications such as thread inspection, bore diameter testing and spacing checks. Manufactured from specially hardened, low-distortion alloys and fine-lapped for minimal measurement uncertainty, the range includes thread plug gauges, precision plug gauges and calibration gauge blocks to ensure long-term repeatability and wear resistance.
14.8mm Gauge Pin 50mm Length Workshop Version - Metav IndustryLine
Take advantage of the precise combination of Ø14.8 mm diameter, 50 mm length and ±0.002 mm accuracy for consistent inspection results in the workshop; order the gauge pin directly from Metav Werkzeuge or consult our technical advisers for application advice. Gauge pin, single, Ø14.8 mm × 50 mm — Metav IndustryLine A gauge pin designed for workshop inspection and end‑dimension checks, providing a compact, traceable probe for assembly, testing and quality control. Diameter 14.8 mm precision Length 50 mm workshop version Accuracy ±0.002 mm Special steel construction Reliable precision for routine inspection needs This compact measuring element offers repeatable dimensional control where small tolerances matter. With a nominal diameter of 14.8 mm and a measured length of 50 mm, the component is suitable for end‑dimension checks, plug‑gauge comparisons and fixture verification. The specified accuracy of ±0.002 mm supports tight inspection limits and reduces rework by identifying deviations early in the process. The robust design is intended for regular workshop use and integrates easily into manual and semi‑automated inspection routines. Durable material and straightforward handling Constructed from special steel, the pin balances surface hardness with machinability to withstand frequent use while keeping form stability. The compact geometry and modest mass (approx. 0.1 kg) simplify handling and positioning in jigs or test nests, helping to speed up repetitive measuring tasks. The workshop configuration emphasises practicality: quick visual identification, secure seating in gauge holders and predictable behaviour under typical shop conditions, which contributes to shorter inspection cycles and improved throughput. Traceability, identification and integration Identification by SKU M323.E80 and GTIN allows straightforward stock control and ordering, while the eClass entry supports catalogue and ERP integration. The clear technical specification—Ø14.8 mm, 50 mm length, special steel, ±0.002 mm—facilitates selection for compatible assemblies and fixtures, avoiding mismatches during procurement. Where batch consistency and traceable parts lists are required, this probe can be referenced directly in documentation and production plans to ensure reproducible measurement outcomes. For reliable workshop measurement choose the Metav IndustryLine gauge pin (M323.E80) — contact Metav Werkzeuge in Emmerich for ordering and specific application advice by phone +49 2822 7131930 or e‑mail info@metav-werkzeuge.com Technical data Article number: M323.E80 GTIN: 4061905068485 Category: Messstifte eClass: 21170231 Facts Diameter: 14.8 mm Length: 50 mm Weight: 0.1 kg Accuracy: ±0.002 mm Special features Workshop version Material: Special steel Story trigger: End dimensions FAQ What inspection tasks is this gauge pin suited for? The gauge pin is suited for end‑dimension checks, plug comparisons and fixture verification in general workshop and production contexts. What is the declared tolerance for this measuring pin? The measuring element is specified with an accuracy of ±0.002 mm, allowing tight control for dimensional checks. Which material is used for the pin and why does it matter? The pin is made from special steel; this offers a balance of wear resistance and dimensional stability for repeated workshop use. How is the item identified for ordering and inventory? The product is listed as SKU M323.E80 with GTIN 4061905068485 for straightforward procurement and stock management. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
14.91mm Gauge Pin, Single, 50mm Length, Workshop Version - Metav IndustryLine
Taking advantage of a workshop‑grade design, tight ±0.002 mm tolerance and a compact 14.91 mm nominal diameter, this single gauge pin ensures repeatable reference measurements in production and inspection routines. Order the test pin directly via Metav Werkzeuge or ask the consultants for matching sets and delivery options. Metav IndustryLine Test Pin M323.E91 — Single gauge pin, Ø 14.91 mm, 50 mm length The test pin M323.E91 is a workshop‑grade gauge element for precise end‑measurement and go/no‑go checks, with a nominal diameter of 14.91 mm and a length of 50 mm. Workshop version for daily shop use Nominal diameter 14.91 mm for end‑measurement 50 mm length in hardened special steel Tolerance ±0.002 mm for high repeatability Consistent accuracy for production control The compact gauge element delivers a certified repeatability of ±0.002 mm, making it suitable for fine inspection tasks and dimensional checks where small deviations matter. As a precision reference with a nominal diameter of 14.91 mm, the component supports reliable pass/fail decisions and reduces rework by keeping measurement scatter low. The stated tolerance and the short, stiff geometry combine to minimise bending and operator‑induced error, providing a stable reference in routine quality control. Robust workshop design that lasts Built as a workshop version, the pin is manufactured from special steel and finished for durability in daily use. The 50 mm length offers a practical engagement depth for many end‑measurement and alignment tasks while keeping handling straightforward. Delivered in a protective case for transport, the gauge arrives ready for safe storage and easy retrieval at the bench. The compact mass (approx. 0.1 kg) and hardened construction resist wear, extending service life under repetitive contact conditions. Integration into inspection workflows As a single gauge pin with SKU M323.E91, the component is straightforward to integrate into inspection fixtures, comparative checks and set‑up procedures. Marked traceability with GTIN 4061905070365 simplifies inventory and compliance documentation. The combination of compact form, robust material and tight tolerance supports automated and manual gauging alike, improving throughput by making reference measurements faster and less ambiguous. For workshop environments that demand dependable reference gauges, choose Metav IndustryLine — contact Metav Werkzeuge in Emmerich for tailored supply and advice via info@metav-werkzeuge.com or +49 2822 7131930 Technical Data Article number: M323.E91 GTIN: 4061905070365 Brand: Metav IndustryLine Facts Nominal diameter: 14.91 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.1 kg Special features Material: special steel Workshop version Delivered in protective case for transport Designation: test pin, single FAQ What is the primary use of this test pin? The test pin M323.E91 from Metav IndustryLine is intended for end‑measurement, reference checks and go/no‑go gauging in workshop and inspection applications. Is the material specified for wear resistance? Yes, the gauge pin is made from special steel, a choice that gives the M323.E91 increased wear resistance and dimensional stability under frequent contact. What measurement accuracy can be expected? The single gauge pin provides a tolerance of ±0.002 mm, which supports high repeatability in routine inspection tasks. How is the item supplied for transport and storage? The pin is delivered in a protective case suitable for transport, ensuring safe handling from the warehouse to the workshop bench. Can the M323.E91 be used in fixture setups and inventory systems? Yes, the test pin is well suited to fixture integration and its GTIN (4061905070365) and SKU (M323.E91) make inventory tracking and documentation straightforward. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
14.92mm Gauge Pin Length 50mm Workshop Version - Metav IndustryLine
Take advantage of precise end‑measurement capability and workshop robustness thanks to a Ø 14.92 mm diameter and a verified tolerance of ±0.002 mm, supplied ready for transport in a protective case; order the test pin directly via Metav Werkzeuge or consult the sales team if clarification is required. M323.E92 test pin – Gauge pin, Ø 14.92 mm, 50 mm length (Metav IndustryLine) A M323.E92 test pin designed as a workshop‑grade gauge pin for precise end‑measurement and alignment tasks in inspection and assembly environments. Workshop version, robust construction Diameter Ø 14.92 mm, tolerance ±0.002 mm 50 mm overall length for end‑measurement Supplied in protective transport case Precision for repeatable end‑measurement The M323.E92 functions as a precision gauge pin for end‑measurement, alignment and fixture checks, offering a consistent datum for inspection tasks. With a nominal diameter of Ø 14.92 mm and a declared tolerance of ±0.002 mm, the component provides a narrow dimensional window that supports reproducible measurements and reliable plug‑gauge references. This accuracy reduces uncertainty in pass/fail evaluations and aids quality control in production and rework operations. Workshop‑grade design and material advantages Manufactured from special steel, the pin is intended for demanding shop use where mechanical robustness matters. The workshop‑grade execution ensures handling and deployment in routine measurement cycles without excessive concern for minor knocks during use. Supplied in a protective transport case, the pin remains protected during storage and transit, preserving its dimensional integrity and extending service life while simplifying logistics on the shop floor. Practical uses and integration into inspection workflows Designed for end‑measurement applications, the pin serves as a reference element in fixture setup, bore gauging and alignment procedures. The 50 mm overall length offers sufficient engagement for most standard checks while keeping the component compact for handling. As a single‑piece test pin, it integrates easily into measurement benches, pin gaugesets or bespoke inspection fixtures where a precise cylindrical datum is required for comparative and go/no‑go assessments. For workshop-ready precision order the M323.E92 gauge pin via Metav Werkzeuge or contact the Metav team at info@metav-werkzeuge.com / +49 2822 7131930 to discuss suitability for specific inspection tasks Technical data SKU: M323.E92 GTIN: 4061905070372 Material: Special steel Diameter: 14.92 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.1 kg Category: Gauge pin (Messstifte) Delivery: single item in transport case Special version: Workshop execution Facts Diameter (numeric): 14.92 mm Length (numeric): 50 mm Tolerance (numeric): ±0.002 mm Weight (numeric): 0.1 kg GTIN (numeric): 4061905070372 Special features Workshop‑grade construction Supplied in protective transport case Single test pin for end‑measurement and alignment Manufactured from special steel FAQ What are the exact dimensions of the pin? Diameter 14.92 mm, overall length 50 mm for the M323.E92 test pin. What tolerance is specified for this gauge pin? The pin is specified with a dimensional tolerance of ±0.002 mm. Which material is used for the M323.E92? The pin is manufactured from special steel. Is the pin intended for shop or laboratory use? The M323.E92 is a workshop‑grade gauge pin, designed for robust shop use and routine inspection tasks. Does the delivery include protective packaging? Yes, the pin is supplied as a single item in a protective transport case. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
14.93mm Gauge Pin Length 50mm Workshop Version - Metav IndustryLine
Take advantage of the combination of high repeatability, compact dimensions and workshop-suited robustness to keep fine‑mechanical inspection tasks reliable and efficient; order the required inspection pins directly via Metav Werkzeuge or consult our advisers for specification support. Gauge pin, single inspection pin Ø 14.93 mm – 50 mm length (Metav IndustryLine) The gauge pin, single inspection pin Ø 14.93 mm – 50 mm length is a precision measurement pin for fine mechanical and workshop use, intended for end‑measure checks, fixture alignment and dimensional verification in small bore applications. Workshop version, robust design Diameter 14.93 mm precision fit Tolerance ±0.002 mm accuracy Supplied in transport box Precise diameter and tight tolerance for repeatable checks The inspection pin delivers a diameter of 14.93 mm with a tolerance of ±0.002 mm, which corresponds to a 2 µm deviation and supports highly repeatable measurements in fine‑mechanical contexts. Such accuracy reduces rework and inspection time by providing a stable reference for bore gauging and end‑measure verification. The combination of special steel construction and a compact form factor ensures that dimensional stability is maintained during handling and short measurement cycles, making this gauge especially suitable where small tolerances are decisive. Compact length and workshop design that aid everyday handling With a length of 50 mm and a low mass (approx. 0.1 kg), the pin is easy to position by hand yet rigid enough to avoid significant deflection during typical workshop tasks. The declared workshop execution underlines durability under frequent use in production and maintenance environments. Delivery in a transport box (plastic or wooden) protects the item during storage and transit, preserving the measurement surface and supporting clean handling procedures between uses. The small footprint makes the pin a practical addition to inspection kits and jigs without occupying excessive space. Application range and benefit for quality processes Classified within the micro measurement range (maximum span up to 100 mm), this inspection pin is tailored to fine‑mechanical work such as small bore checking, alignment of fixtures and end‑measure standards for assembly or repair operations. The robust material and tight tolerance support repeatability and reliable pass/fail comparisons when used alongside calibrated measuring systems. As a precision tool from a recognised industrial line, the pin contributes to consistent quality control and helps shorten the feedback loop between measurement and corrective action on the shop floor. Contact Metav Werkzeuge for procurement details and specification advice based on the Metav IndustryLine range; our advisers can confirm suitability for specific inspection tasks and provide ordering assistance. Technical data Article number: M323.E93 GTIN: 4061905070389 SKU: M323.E93 Facts Diameter: 14.93 mm Length: 50 mm Weight: 0.1 kg Tolerance: ±0.002 mm Special features Material: Special steel Workshop execution Supplied in transport box (plastic/wood) Category: Gauge pins FAQ What level of accuracy does this inspection pin offer? The inspection pin provides an accuracy of ±0.002 mm, making it suitable for applications that require micrometre‑level repeatability; the specification is part of the Metav IndustryLine gauge pin data (SKU M323.E93). For which types of measurements is the pin intended? This gauge pin is intended for end‑measure checks, bore verification and fixture alignment in fine‑mechanical and workshop settings, where the 14.93 mm diameter and 50 mm length suit small‑format components. What is the material and how does it affect durability? Constructed from special steel, the pin from Metav IndustryLine combines surface resilience with dimensional stability, supporting frequent workshop use while maintaining measurement integrity. Is the pin suitable for inclusion in inspection kits? Yes, the compact dimensions and protected delivery in a transport box make this pin suitable for inspection kits and portable measurement sets; the low weight also eases handling during repeat checks. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
14.94mm Gauge Pin Length 50mm Workshop Finish, ±0.002 Accuracy - Metav IndustryLine
Take advantage of the high repeatability and tight tolerance of this workshop test pin to secure consistent end‑measure inspections; its 14.94 mm diameter and 50 mm length in special steel make it a compact, robust solution for routine gauging. Order directly via Metav Werkzeuge or consult our specialists for supply and logistics. Gauge pin, single — 14.94 mm dia, 50 mm length (Metav IndustryLine) The Gauge pin, single, 14.94 mm, 50 mm is a workshop‑grade test pin designed for precise end‑measurement checks and go/no‑go gauging in compact inspection setups. Workshop execution, robust design Diameter exactly 14.94 mm for end‑measure use High precision tolerance ±0.002 mm Supplied in a protective transport case Precision for fine mechanical inspection The compact design targets applications that demand repeatable small‑part checks: with a diameter of 14.94 mm and a specified tolerance of ±0.002 mm, the pin suits fine mechanical inspection where minimal clearance matters. Classified in the micro measuring range (10–100 mm), this test pin combines dimensional stability and short jaw geometry to reduce bending and positional error during routine go/no‑go checks, making it an efficient measuring artefact for workshop metrology and component end‑measure verification. Durable material and workshop readiness Manufactured from special steel, the pin is engineered for wear resistance and consistent surface quality that preserves its gauge dimensions under repeated use. The workshop execution emphasises practical handling: chamfers for easy entry, a hardened shaft for longevity and a finish that minimises surface corrosion. Delivered in a protective transport case, the pin is protected during storage and transit, easing workshop logistics and reducing the risk of damage before use. Practical benefits for production control As a single‑piece gauge, the test pin streamlines quick fit checks, alignment testing and reference measurements on jigs and fixtures. The combination of compact length (50 mm) and tight tolerance supports rapid decision‑making on the shopfloor: inspect, accept or reject with minimal setup. Traceable identification (SKU M323.E94, GTIN 4061905070396) assists inventory management and documentation in quality workflows while the familiar gauge‑pin format integrates easily with existing plug‑gauge routines and inspection fixtures. For workshop‑grade end‑measure checks, contact Metav Werkzeuge in Emmerich to secure the Metav IndustryLine M323.E94 gauge pin and confirm delivery and packing options: info@metav-werkzeuge.com / +49 2822 7131930 Technical Data Article number: M323.E94 GTIN: 4061905070396 Category: Gauge pin (test pin) Facts Diameter: 14.94 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.1 kg Special features Material: Special steel Workshop execution Supplied in protective transport case SKU: M323.E94 FAQ What is the intended use for this gauge pin? The gauge pin is intended for end‑measure checks, go/no‑go gauging and alignment tasks in workshop inspection where compact, repeatable measurements are required. What accuracy can be expected from the test pin? The test pin offers a tolerance of ±0.002 mm, providing high repeatability suitable for fine mechanical inspection and tight fit verifications. Is the pin ready for immediate use after delivery? Yes; the Metav IndustryLine gauge pin M323.E94 is supplied in a protective case and ready for workshop use without further preparation. What material is the pin made from and how does that affect wear? The pin is manufactured from special steel, chosen for surface durability and dimensional stability to withstand repeated insertion and contact during inspection. How does the 14.94 mm diameter fit into measurement categories? With a diameter of 14.94 mm and a 50 mm length, the item falls into the micro measuring range (10–100 mm), optimised for precision work on small components. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
14.95mm Gauge Pin 50mm Length Workshop Version - Metav IndustryLine
Take advantage of the 14.95 mm diameter and ±0.002 mm accuracy for reliable end‑dimension verification and repeatable workshop measurements; the robust workshop design and delivery in a transport case keep the pin protected during handling and transport. Order the gauge pin directly via Metav Werkzeuge or consult our advisors for specification matching and procurement assistance. Gauge pin, single, 14.95 mm diameter · 50 mm length — Metav IndustryLine The gauge pin, single, 14.95 mm diameter and 50 mm length is a precision inspection pin designed for end‑dimension checks and alignment tasks in workshop and production environments Workshop version, robust design Diameter 14.95 mm with high accuracy 50 mm length for compact measurements Special steel construction for wear resistance Reliable precision for end‑dimension verification The inspection pin delivers a measured tolerance of ±0.002 mm, positioning it in the high‑precision range for small components. As a compact gauge in the micro range (measurement span under 100 mm), it is optimised for fine mechanical work where short measuring faces reduce torsion and improve repeatability. The specified diameter of 14.95 mm is produced to tight dimensional control, enabling consistent fits and go/no‑go assessments in assembly and inspection routines. This level of accuracy reduces rework and supports tighter process control across batch runs. Robust design for everyday workshop use Manufactured from special steel, the pin is engineered to resist wear in frequent use while maintaining its critical dimensions. The 50 mm length provides a secure working grip without excess overhang, aiding manual handling and gauge insertion in jigs or bore checks. Supplied as a workshop edition, the component is finished and prepared for practical shopfloor conditions. Delivery includes a protective transport case, which simplifies storage and reduces the risk of damage in transit — a pragmatic choice for mobile metrology or multi‑workstation environments. Practical advantages for quality control and throughput As a single plug‑style gauge, the component is easy to integrate into inspection sequences and serves as a straightforward reference for end‑dimension checks and alignment tasks. The compact form factor and proven material choice contribute to repeatability and long service life, helping to maintain consistent quality control across production cycles. The part’s clear labelling and SKU facilitate inventory management and fast replacement, supporting lean stocking practices in maintenance and inspection departments. Contact Metav Werkzeuge for tailored advice and procurement of the Metav IndustryLine gauge pin (M323.E95) with 14.95 mm diameter and 50 mm length — expert support from Emmerich for quick delivery and specification checks. Technical data Article number: M323.E95 GTIN: 4061905066559 Label: Prüfstift, einzeln, 14,95 mm Länge 50 mm Weight: 0.1 kg Material: Special steel Measurements Diameter: 14.95 mm Length: 50 mm Accuracy / tolerance: ±0.002 mm Features Workshop version (robust design) Delivered in transport case for safe handling Category: Gauge pins (Messstifte) eClass: 21170231 FAQ Is the pin suitable for precision go/no‑go checks on bores? The gauge pin is suitable for go/no‑go and end‑dimension checks; the 14.95 mm diameter and ±0.002 mm tolerance make it appropriate for tight bore verification and alignment tasks. What material is the gauge pin made from and how durable is it? The pin is manufactured from special steel, chosen for wear resistance under frequent contact; this ensures durability in routine workshop inspection as supplied by Metav IndustryLine. Does the product arrive ready for use and how is it packaged? The single gauge pin is supplied ready for workshop use and is delivered in a protective transport case to reduce handling damage during storage and movement. Can this pin be used in assembly jigs and fixtures? Yes — the compact 50 mm length and stable diameter make the pin well suited for use in jigs, fixtures and manual alignment procedures in production settings. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
14.96mm Test Pin 50mm Length Workshop Version - Metav IndustryLine
Taking advantage of precision, robust workshop construction and compact dimensions, this gauge pin ensures reproducible end‑dimension checks for small parts; order directly via Metav Werkzeuge or contact our advisors for specification support. Gauge pin M323.E96 — single plug gauge, 14.96 mm Ø × 50 mm (Metav IndustryLine) The gauge pin M323.E96 is a workshop‑grade precision plug gauge designed for end‑dimension verification of small mechanical components and fits inspection fixtures and gauge blocks. Workshop‑grade construction Diameter 14.96 mm for end‑dimension checks Tolerance ±0.002 mm for high accuracy Precision where space and repeatability matter This compact plug gauge delivers reliable measurements for small bores and end dimensions thanks to a nominal diameter of 14.96 mm and a 50 mm length that keeps the effective measuring span short and stiff. The specified tolerance of ±0.002 mm translates into dependable repeatability during serial inspections and short‑run production checks. Constructed from special steel, the pin resists wear in routine workshop use while providing a consistent reference for fit and clearance decisions. Designed for practical workshop workflows Built as a workshop‑grade component, the pin integrates easily with benches, jigs and portable inspection setups. The compact geometry reduces handling time and simplifies alignment in fixtures, helping to speed up go/no‑go evaluations and minimise rework. Delivery in a dedicated transport box protects the finish during storage and transit and keeps the pin ready for immediate use in maintenance rounds or setup checks. Its size places it in the micro range of precision plugs, making it suitable for watchmaking, instrument parts and small‑bore components. Clear applications and measurable benefits Ideal for end‑dimension verification, assembly checks and comparative gauging, this plug gauge provides a concise traceable reference that improves first‑pass yields and assembly certainty. The combination of special steel construction and tight dimensional control supports reproducible fits and reduces the need for downstream adjustments. For workshops and quality cells requiring compact, accurate reference pins, this product helps standardise measurement routines and shortens inspection cycles while preserving component integrity. Secure workshop precision with Metav IndustryLine gauge pins — contact Metav Werkzeuge in Emmerich for tailored advice and order support at info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: M323.E96 GTIN: 4061905066566 Manufacturer: Metav IndustryLine Facts Diameter: 14.96 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.1 kg Special features Workshop execution Material: Special steel Delivered in transport box Category: Messstifte FAQ What is the nominal diameter and length of this gauge pin? The gauge pin M323.E96 has a nominal diameter of 14.96 mm and a length of 50 mm suitable for compact inspection tasks. How accurate is the plug gauge for end‑dimension checks? Accuracy is specified as ±0.002 mm, which supports consistent repeatability for small‑part inspections and assembly verifications. Is the pin suitable for routine workshop use and transport? Yes. The M323.E96 is a workshop‑grade plug gauge made from special steel and supplied in a transport box to protect the finish during handling. Which applications is this gauge pin best suited for? This plug gauge is intended for end‑dimension verification, small‑bore inspection and fixture checks in machine shops, tool rooms and quality control stations. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
14.97mm Gauge Pin, Single, 50mm Length, Special Steel, Workshop Version - Metav IndustryLine
Take advantage of a compact, dimensionally stable inspection pin that combines a 14.97 mm tolerance fit with a ±0.002 mm accuracy specification and a robust workshop design for repeatable fixture and end‑measurement tasks; order directly via Metav Werkzeuge or consult our team for application advice. Gauge pin M323.E97 — 14.97 mm diameter, 50 mm length (Workshop version) — Metav IndustryLine A gauge pin M323.E97 designed for precise end‑measurement and fixture alignment in workshop and inspection environments. Precision fit: 14.97 mm diameter 50 mm length for fixture set‑ups Accuracy ±0.002 mm Workshop version, robust design Supplied in transport case Engineered for reliable end‑measurement and repeatability The gauge pin is manufactured to a narrow diameter of 14.97 mm, delivering a tight fit where consistent control of the mating tolerance is required. With a specified accuracy of ±0.002 mm, this pin supports high‑precision checks and comparative gauging in routine quality control. The compact 50 mm length and low mass make it suitable for quick insertion into jigs, plug gauges or assembly fixtures while maintaining dimensional stability during use. These properties translate into fewer reworks and more predictable inspection outcomes. Practical handling and workplace advantages Constructed from special steel, the pin balances stiffness and wear characteristics appropriate for workshop handling and repeated insertion cycles. Its modest weight of 0.1 kg and the workshop‑oriented finish simplify manual handling during set‑up. Delivery in a transport case protects the datum surfaces in transit and storage, preserving the measuring length and contact faces until use. The solid construction and packaging reduce downtime for replacement and help to maintain calibration intervals by preventing accidental damage. Suited to inspection, assembly and fixture alignment workflows This single gauge pin is a straightforward tool for end‑dimension verification, alignment of bores and locating pins in assembly fixtures. Where quick comparative inspection is required, the pin acts as a reliable reference gauge to verify bore sizes, seating planes and positional fits without complex measuring devices. Its workshop specification ensures resilient performance in production environments, while the clear dimensional and tolerance information facilitates integration into quality documentation and work instructions. Contact Metav Werkzeuge for application guidance on the M323.E97 gauge pin and to confirm compatibility with existing jig and inspection systems — our Emmerich team provides fast, practical support. Technical data Article number: M323.E97 GTIN: 4061905066573 Label: Gauge pin, single, 14.97 mm diameter, 50 mm length Manufacturer: Metav IndustryLine Core specifications Diameter: 14.97 mm Length: 50 mm Weight: 0.1 kg Tolerance/accuracy: ±0.002 mm Materials & features Material: Special steel Workshop version Supplied in transport case SKU: M323.E97 FAQ What tolerance is specified for this gauge pin? The gauge pin M323.E97 is specified with an accuracy of ±0.002 mm, suitable for fine comparative checks and tight fitting tests. Which material is used for the pin? The M323.E97 is made from special steel, chosen for dimensional stability under routine workshop use. Is the pin supplied ready for immediate use out of the box? The product is supplied in a transport case to protect measuring faces; no calibration certificate is indicated in the product data. Can this pin be used for fixture alignment and bore checking? Yes. The 14.97 mm diameter and 50 mm length make it well suited for fixture alignment, bore checks and locating tasks in assembly and inspection workflows. How is the item identified for ordering? Order using the article number M323.E97 or GTIN 4061905066573 to ensure the correct workshop‑version gauge pin is supplied. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
14.98mm Test Pin 50mm Length Workshop Version - Metav IndustryLine
Reliable workshop-grade gauge pin offering a compact 14.98 mm diameter, 50 mm usable length and a tight ±0.002 mm tolerance for repeatable end-dimension checks; the special steel construction and protective transport case support durability and safe storage. Order this precision pin directly via Metav Werkzeuge or consult our advisors for application guidance. Gauge pin, single — 14.98 mm diameter, 50 mm length (M323.E98, Metav IndustryLine) Gauge pin, single, 14.98 mm / 50 mm — a compact measuring element for precise end‑dimension checks and fixture setting in workshop metrology. Workshop version for robust daily use Precise 14.98 mm diameter 50 mm usable length Dimensional tolerance ±0.002 mm Supplied in protective transport case Precision that reduces rework and speeds inspection A compact reference element delivers measurable gains on the inspection bench: the 14.98 mm diameter and ±0.002 mm specification provide a reproducible reference for end‑dimension verification, alignment and quality control. Built to the requirements of everyday production, this measuring dowel translates high geometric fidelity into faster decision cycles on go/no‑go checks and dimensional reporting. The tight tolerance reduces measurement scatter and therefore the need for repeat checks, improving throughput without compromising traceability. Designed for workshop handling and fixture integration The short, rigid form and 50 mm usable length make the component easy to mount in jigs, gauges and setting fixtures; its workshop version designation indicates a focus on handling resilience and practical fit. The weight of approximately 0.1 kg and the balanced geometry support steady seating in sockets and bores, while the delivered transport case keeps the measuring surface protected between uses. Integration into existing inspection routines is straightforward, with the pin serving as a reliable datum for both single‑point checks and comparative set‑ups. Durable material and clear application focus Manufactured from special steel, the pin resists everyday wear while maintaining its geometric integrity under normal workshop conditions. The construction supports repeated insertion and withdrawal, preserving the measurement edge and extending service life. As an end‑dimension reference element, it suits routine production checks where consistent repeatability is essential. For customers seeking a robust, no‑nonsense measuring component, this unit offers an attractive balance of accuracy, durability and operational simplicity under the Metav IndustryLine label. For application advice or specification confirmation for the M323.E98 gauge pin, contact Metav Werkzeuge in Emmerich — call +49 2822 7131930 or email info@metav-werkzeuge.com to discuss suitability and procurement options Technical data SKU: M323.E98 GTIN: 4061905067365 Brand: Metav IndustryLine Material: special steel Version: workshop execution Weight: 0.10 kg Facts Diameter: 14.98 mm Usable length: 50 mm Tolerance: ±0.002 mm Special features Supplied in protective transport case Compact reference for end‑dimension checks Suitable for jig and fixture integration Robust handling properties for daily workshop use FAQ What is the exact diameter and length of this gauge pin? The pin is specified with a diameter of 14.98 mm and a usable length of 50 mm; the product is listed as M323.E98 from Metav IndustryLine. How precise is the measuring element? Precision is stated as ±0.002 mm, which makes the M323.E98 suitable for repeatable end‑dimension verification in workshop environments. Is the pin delivered with any protective packaging? Yes, the gauge pin is supplied in a protective transport case to preserve the measuring surfaces during storage and transit. Can this pin be used as a datum in fixtures and jigs? The compact form and 50 mm usable length allow the pin to be integrated as a datum or reference element in fixtures and setting gauges. What material is the pin made from and how does that affect durability? Constructed from special steel, the measuring pin is designed for durability under regular workshop handling and repeated insertion cycles. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
14.99mm Test Pin 50mm Length Workshop Finish - Metav IndustryLine
The precise combination of a 14.99 mm diameter, 50 mm length and ±0.002 mm repeatability delivers reliable go/no‑go and end‑measurement checks; order the gauge pin directly via Metav Werkzeuge or consult the team for application advice. Gauge pin M323.E99 — single inspection pin, 14.99 mm dia, 50 mm length (Metav IndustryLine) A gauge pin, single piece with a 14.99 mm nominal diameter and 50 mm usable length, designed for workshop measurement tasks and end‑size verification in production and assembly. Precision diameter 14.99 mm for tight fits Length 50 mm for compact inspection tasks Accuracy ±0.002 mm for reproducible checks Reliable inspection for tight tolerances The compact solid pin provides a clear, measurable datum for both go/no‑go and end‑measure operations, making it suitable where consistent repeatability is essential. With a nominal diameter of 14.99 mm and an accuracy of ±0.002 mm, the pin reduces uncertainty in assembly and inspection routines, lowering the risk of rework. The hardened special steel construction maintains geometric stability under routine handling, so dimensional checks remain trustworthy over many cycles. Built for daily workshop use Manufactured as a workshop version, the pin balances durability with practical handling: the 50 mm length gives sufficient engagement without excess overhang, supporting quick manual verifications at the bench or on the shop floor. The robust material choice ensures resistance to wear and straightforward cleaning after use. This combination of form and material supports faster inspection cycles and contributes to uninterrupted production flow by making simple checks quick and dependable. Integrating precision into quality workflows As an individual inspection element, the pin is straightforward to incorporate into existing jigs, fixtures and test benches; the consistent 14.99 mm sizing simplifies interchangeability and stocking. Where documented traceability is required, the supplied product details (SKU and GTIN) permit straightforward identification in quality records. The result is a compact, repeatable measuring aid that helps maintain process capability and supports documented quality assurance across small‑batch and series production. For precise workshop checks specify the Metav IndustryLine gauge pin M323.E99 and contact Metav Werkzeuge in Emmerich for tailored advice and local delivery options — info@metav-werkzeuge.com, +49 2822 7131930 Technical data Article number: M323.E99 GTIN: 4061905067372 Manufacturer: Metav IndustryLine Facts Diameter: 14.99 mm Length: 50 mm Accuracy: ±0.002 mm Weight: 0.1 kg Special features Workshop version Material: special steel Single inspection/gauge pin Intended use: end‑size/end‑measure checks ECLASS: 21170231 FAQ What is the nominal diameter and why is 14.99 mm relevant? The nominal diameter of the gauge pin is 14.99 mm; this near‑limit size allows verification of holes and fits where tight clearances are specified, ensuring components meet dimensional requirements. Is the pin suitable for repeated workshop use? Yes, the workshop version construction in special steel is designed for regular handling and routine inspections without rapid degradation. Can this pin be used as a reference in jigging or fixture tests? The single pin format and consistent 14.99 mm sizing make it suitable as a datum element in jigs and fixtures for quick verification and alignment tasks. What does the stated accuracy ±0.002 mm mean in practice? An accuracy of ±0.002 mm indicates very small deviation in diameter, supporting reproducible checks and reducing measurement uncertainty during quality control. How is the product identified for ordering or stock management? The product is listed under SKU M323.E99 and GTIN 4061905067372, which can be used for procurement and traceability. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
14.9mm Gauge Pin 50mm Length Workshop Version, Special Steel - Metav IndustryLine
Take advantage of workshop-grade precision and robust construction combined with a tight ±0.002 mm manufacturing tolerance and a 14.9 mm nominal diameter for reliable end-size verification; order directly through Metav Werkzeuge or consult our specialists for application advice. Test pin M323.E90 — Gauge pin for end-dimension checks, 14.9 mm Ø, 50 mm length (Metav IndustryLine) Test pin M323.E90 serves as a compact, workshop-grade verification pin designed for dimensional checks in production and inspection routines, especially for end-size measurements and repeatability checks. 14.90 mm nominal diameter for bore checks 50 mm overall length for deep bores ±0.002 mm manufacturing tolerance Special steel, workshop execution Reliable metrology performance for daily inspection tasks The pin is engineered for consistent results in routine quality control: the 14.9 mm nominal diameter combined with a manufacturing tolerance of ±0.002 mm reduces uncertainty when checking bores, seats and mating parts. This level of precision supports efficient pass/fail decisions on the shop floor and integrates smoothly into go/no-go checks or fixture-based verification. The technical specification is deliberately straightforward so that measurement departments can rely on repeatable dimensional references without elaborate setup. Robust design that withstands workshop handling With a total length of 50 mm and a compact form factor, the pin balances reach and rigidity to resist bending during typical handling. Constructed from special steel in a workshop execution, the component provides durable contact surfaces that maintain geometry under regular use. The relatively low mass (0.1 kg) aids quick manipulation and placement in fixtures, while the controlled tolerance ensures the pin remains a stable reference across production cycles, reducing rework and inspection time. Fits into inspection workflows and documentation The M323.E90 pin is suitable for plain mechanical checks and can be used alongside calipers, micrometres and coordinate inspection systems as a reliable reference for end dimensions. The item’s traceable identifiers (SKU M323.E90, GTIN 4061905070358) make it straightforward to include in inventory lists and inspection protocols. For specialised applications or integration into bespoke gauges, Metav Werkzeuge’s metrology advisors can advise on compatible fixturing and handling practices to ensure the pin’s characteristics are fully utilised in process control. Choose the Metav IndustryLine M323.E90 for dependable workshop verification and contact Metav Werkzeuge in Emmerich for targeted application support: info@metav-werkzeuge.com / +49 2822 7131930 Technical data Article number: M323.E90 GTIN: 4061905070358 Label: Test pin, single, 14.9 mm diameter, length 50 mm Facts Diameter: 14.9 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.1 kg Special features Material: Special steel Workshop execution (robust handling) Category: Gauge pin / Test pin FAQ What is the intended use for this test pin? The M323.E90 test pin is intended for end-dimension verification, bore checks and fixture-based pass/fail inspection in workshop and production environments. How precise is the gauge pin? This gauge pin is manufactured to a tolerance of ±0.002 mm, offering high repeatability for routine inspection tasks. Which material is the pin made from? The pin is made from special steel and comes in a workshop execution suitable for regular handling. Can the pin be included in documentation and traceability systems? Yes, the M323.E90 includes identifiers such as SKU M323.E90 and GTIN 4061905070358 for inventory and inspection record keeping. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
140mm Setting Ring, Hardened Gauge Steel, Form C, DIN 2250/DIN 286 JS3 - Metav IndustryLine
A compact, standards‑led choice for workshop reference: combine DIN 2250 conformity, a 140 mm diameter and hardened, lapped gauge steel for repeatable setup and long service life — order the setting ring directly via Metav Werkzeuge or consult our specialists for application advice. Setting ring 140 mm (DIN 2250) — hardened gauge steel, Form C (Metav IndustryLine) A setting ring 140 mm designed as a precision reference for ring gauging, fixture setup and dimensional verification across inspection and production environments. *DIN 2250 and DIN 286, JS 3 compliance *Hardened, lapped gauge steel *Form C profile for standard fits *Diameter 140 mm for common fixture setups Reliable standards that support reproducible processes The component is manufactured to DIN 2250 and DIN 286 with JS 3 tolerance, providing a clear reference for calibre checks and machine setup. This standards conformity translates into predictable limits for go/no‑go assessment and reduces the need for interim rework. With a nominal 140 mm bore and a design intended for repeatable seating, the part functions as a robust reference gauge that streamlines inspection routines and shortens the time from initial setup to productive machining. Material and geometry that minimise measurement uncertainty Made from hardened, lapped gauge steel, the item combines surface integrity with dimensional stability. The Form C profile ensures a defined fit to mating parts while the lapped finish reduces local contact stress and wear, which keeps deviations low over prolonged use. At 3.85 kg the mass provides inherent stability when used in fixture jigs or bench inspection, helping to avoid unintended movement and enabling more reproducible readings during repetitive checks. Practical applications in workshop and inspection workflows This ring is suited to ring gauging, fixture alignment, calibration stands and as a master reference for checks on assemblies and turning work. The geometry supports standard fit types used in toolrooms and quality labs, making it an appropriate choice for both incoming inspection and in‑process verification. As a reference element, the setting ring helps maintain traceable tolerances across production batches and reduces downtime associated with ambiguous setup conditions. Confidence from a dedicated precision partner Sourcing this product from Metav IndustryLine ties the physical gauge to a broader supply and service proposition: a wide catalogue of measurement aids, distribution stability from Emmerich and a documented track record in supplying industry‑grade instruments. The combination of standard compliance, robust material treatment and a form matched to common fits offers a pragmatic balance of durability and repeatable accuracy for workshops and inspection departments. For reliable fixture set‑up and long‑term repeatability, order the Metav IndustryLine setting ring 140 mm from Metav Werkzeuge or contact our specialists at info@metav-werkzeuge.com / +49 2822 7131930 for tailored technical guidance. Technical data Article number: M313.140 GTIN: 4054469121130 Diameter: 140 mm Weight: 3.85 kg Facts Tariff code: 90173000 ECLASS: 21170104 Category: Lehren / Messgeräte Special features Material: hardened and lapped gauge steel Standards: DIN 2250 and DIN 286, JS 3 Design: Form C setting ring Usage: reference gauge for fixture setup and dimensional checks FAQ What standards does the setting ring conform to? The setting ring is manufactured in accordance with DIN 2250 and DIN 286 and is produced to a JS 3 tolerance class for consistent reference performance. Is the material suitable for heavy use in an inspection environment? Yes — the ring is made from hardened, lapped gauge steel, a specification intended to resist wear and maintain surface integrity under regular use. Can this ring be used as a master for go/no‑go gauges? The 140 mm setting ring is designed as a precision reference and is suitable for use as a master element in go/no‑go gauging and fixture verification. What advantages does the Form C profile provide? Form C delivers a standardised fit geometry that simplifies mating with common fixtures and gauges, reducing uncertainty during seating and alignment. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
145mm Setting Ring, Hardened Gauge Steel, Form C, DIN 2250/DIN 286 JS3 - Metav IndustryLine
Take advantage of the combination of hardened, lapped gauge steel, DIN 2250 compliance and a stable 145 mm diameter for fast, repeatable set-ups and reliable inspection results. Order the setting ring directly via Metav Werkzeuge or contact our consultants for application advice. Setting ring M313.145 — 145 mm gauge ring, hardened lapped gauge steel (DIN 2250) The Setting ring M313.145 is a precision gauge ring for setting and verifying internal diameters in inspection and toolroom environments, designed to the DIN 2250 standard. Hardened, lapped gauge-steel construction Conforms to DIN 2250 and DIN 286, JS 3 Accurate 145 mm diameter for repeatable setups Robust 4.75 kg mass for stable fixturing Stable reference for repeatable setups A hardened and lapped gauge-steel ring provides a dimensionally stable reference that reduces variability during routine set-ups. The 145 mm nominal diameter, produced to DIN 2250 tolerances, enables precise fixture adjustment and tool presetting with minimal trial adjustments. Using a standard-compliant reference part means fewer rechecks and less machine downtime, helping maintain a predictable production flow. Conformance that simplifies inspection workflows Built to both DIN 2250 and DIN 286 with JS 3 tolerance class, the ring suits quality control processes where documented standards are mandatory. The standardised tolerance and traceable dimension allow calibration chains and inspection protocols to be implemented consistently. This reduces the administrative effort in quality records while ensuring measurable conformance during audits. Mass and form for functional stability At 4.75 kg, the ring offers sufficient mass to remain steady during handling and when placed in fixtures, which translates into fewer measurement artefacts from movement. The listed Form C configuration supports common workshop use and easy seating in mandrels or bore gauges. The combination of mass and finishing treatment (lapped surface) directly improves contact quality with measuring instruments, yielding more reproducible readings. Material and surface finish for longevity Manufactured from hardened gauge steel and finished by lapping, the component resists wear and preserves the critical diameter across repeated use. The lapped finish reduces surface friction and seating irregularities, extending the service life of both the ring and the mating gauges. For environments requiring robust reference tools, this construction minimises long‑term maintenance and replacement frequency. For specific application advice or to secure supply of the Metav IndustryLine setting ring M313.145, please contact Metav Werkzeuge in Emmerich by phone or email for prompt, expert assistance. Technical data Article number: M313.145 GTIN: 4054469121147 Tariff number: 90173000 Category: Lehren Facts Diameter: 145 mm Weight: 4.75 kg Tolerance class: JS 3 Standards: DIN 2250; DIN 286 Special features Material: gauge steel, hardened and lapped Design: Form C Application: reference ring for internal-diameter setting and verification FAQ Is the ring suitable for use as a master for internal-diameter setting? Yes. The setting ring M313.145 (Metav IndustryLine) is designed as a reference for setting and verifying internal diameters and complies with DIN 2250 tolerances. What does the lapped finish mean for daily use? A lapped surface improves contact consistency and reduces wear; for the Metav IndustryLine setting ring, this helps sustain accurate seating and repeatable measurements over time. Which tolerance class does the ring meet and what does that imply? The ring is supplied to JS 3 tolerance, meaning it provides a tight, standardised fit for repeatable inspection and presetting tasks in toolroom and inspection settings. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
15 mm Ceramic Setting Ring 0.001 mm Accuracy, Corrosion‑Resistant ZrO2 Ceramic, HV1250 - Metav IndustryLine
Combining zirconia ceramic construction with HV 1250 hardness and ±0.001 mm accuracy, this ceramic setting ring delivers repeatable set‑up precision and extended wear life for routine metrology tasks. Order the ring directly via Metav Werkzeuge or consult our specialists for application advice. Ceramic setting ring 15 mm 0.001 mm (38x10) — zirconia ceramic, ±0.001 mm accuracy (Metav IndustryLine) The Ceramic setting ring 15 mm 0.001 mm (38x10) is a workshop‑grade precision gauge intended for instrument setting and reference work in metrology and calibration processes. Zirconia ceramic, non‑magnetic and wear‑resistant Accuracy ±0.001 mm for high‑precision set‑up Hardness HV 1250 for long service life Workshop‑grade design for routine metrology Consistent sub‑micron accuracy for set‑up tasks The ring offers ±0.001 mm accuracy, making it suitable where tight reference tolerances are required for setting instruments or verifying calibration fixtures. Manufactured from zirconia ceramic, the component provides excellent dimensional stability across typical workshop temperature fluctuations and resists magnetic interference during sensitive set‑ups. The precision class and measured tolerance reduce ambiguity in reference readings and support reproducible adjustment procedures. Durability that lowers maintenance intervals and costs Thanks to a HV 1250 hardness rating and a wear‑resistant surface, the setting ring withstands repeated engagement without rapid surface degradation. The non‑magnetic property prevents interaction with magnetic tooling or nearby sensors, while the ceramic substrate minimises corrosion risk compared with metallic gauges. These material advantages translate into fewer replacements and more predictable calibration intervals for production and inspection equipment. Practical integration for everyday metrology workflows Designed as a workshop‑grade component, the ring is compact and simple to handle during standard set‑up routines. The geometry and surface finish support stable contact with micrometers, gauges and comparator anvils, enabling reliable transfer standards in bench workflows. Traceable performance and low wear characteristics make the item a practical reference for quality control loops, fixture set‑ups and routine verification tasks across diverse light‑industrial environments. For precision tools and application guidance, contact Metav Werkzeuge in Emmerich to request this Metav IndustryLine ceramic setting ring and expert advice: info@metav-werkzeuge.com | +49 2822 7131930 Technical data Article number: M313.K15 Manufacturer: Metav IndustryLine Description: Ceramic setting ring 15 mm, workshop version Facts Diameter: 15 mm Accuracy: ±0.001 mm Hardness: HV 1250 Special features Material: zirconia ceramic Non‑magnetic Wear‑resistant surface Workshop‑grade construction FAQ What level of accuracy can be expected from this setting ring? The ceramic setting ring provides an accuracy of ±0.001 mm, making it suitable for fine set‑up and calibration tasks where sub‑micron repeatability is required. Is the material suitable for use near magnetic sensors or instruments? Yes. The ring is made from zirconia ceramic and is non‑magnetic, which prevents interference with magnetic sensors and avoids attraction to magnetic tooling. How does the hardness rating affect durability in daily use? With a hardness of HV 1250, the component shows strong resistance to surface wear and contact damage, extending service life in routine metrology operations. Can this ring be used as a transfer standard for micrometre set‑ups? The ring is designed as a workshop‑grade reference and is suitable for setting micrometers and verifying comparator contacts where ±0.001 mm accuracy meets application needs. What identifier should be quoted when ordering or requesting technical details? Please quote the article number M313.K15 (Ceramic setting ring 15 mm 0.001 mm (38x10)) when enquiring about this Metav IndustryLine product. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
15 mm Gauge Ball Pair, Hardened Chrome Steel, 0.003 mm Accuracy, Diameter Tolerance 0.00008 mm - Metav IndustryLine
Take advantage of a compact, wear‑resistant reference solution that combines hardened chrome steel construction, 15 mm diameter and 0.003 mm accuracy for dependable inspection routines; order the pair directly via Metav Werkzeuge or consult our specialists for application advice. Gauge Ball Pair M318.425 — 15 mm, 0.003 mm accuracy (Metav IndustryLine) A matched pair of precision gauge balls for calibration and dimensional inspection in metrology and gauge testing. Hardened chrome steel construction Diameter 15 mm for standard gauges Accuracy 0.003 mm for precision checks Supplied as a matched pair Repeatable reference for high‑precision checks The 15 mm precision spheres provide a stable reference for short‑range verification and comparative gauging. With an accuracy of 0.003 mm and a diameter tolerance of 0.00008 mm, these precision spheres minimise measurement deviation during repeat inspections. The surface roughness 0.00001 ensures low contact variability, while the >HRC 62 hardness rating delivers long‑term wear resistance; this combination reduces the frequency of replacement and supports consistent results in routine quality control. Practical calibration and inspection benefits Designed as a gauge ball pair, the set of two matched spheres simplifies comparative measurements and alignment procedures. Being supplied as a set of two allows for quick checks between a reference and the test item, helping to accelerate throughput without compromising traceability. The matched pairing also aids in detecting measurement system shifts, thereby contributing to lower process uncertainty and improved decision‑making in inspection workflows. Compact handling with workshop readiness The small footprint and modest mass (approx. 0.08 kg per set) make these spheres easy to handle in both bench and fixture‑based operations. Their hardened chrome steel composition provides mechanical stability and resistance to surface damage during routine use. For workshops and inspection labs seeking rugged, low‑maintenance reference elements, the matched pair offers a straightforward upgrade to existing gauge sets and inspection kits, supporting reliable dimension control with minimal setup time. Contact Metav Werkzeuge for tailored advice on integrating the Metav IndustryLine gauge ball pair into existing inspection routines and to discuss order options directly with our specialists Technical data Article number: M318.425 GTIN: 4054469184135 Weight: 0.08 kg Facts Diameter: 15 mm Accuracy: 0.003 mm Diameter tolerance: 0.00008 mm Surface roughness: 0.00001 Hardness: >HRC 62 Pieces per set: 2 Materials & features Material: hardened chrome steel Supplied as a matched pair Suitable for gauge reference and inspection FAQ Are the spheres supplied as a matched set? The gauge ball pair M318.425 is supplied as a matched set of two precision spheres, enabling comparative checks and paired reference use. What are the main dimensional specifications? Diameter is 15 mm with an accuracy of 0.003 mm and a diameter tolerance of 0.00008 mm for the M318.425 pair. Which material and hardness are used? The spheres are made from hardened chrome steel with a hardness exceeding HRC 62 for good wear resistance. What measurement tasks are these balls suitable for? These precision spheres are intended for calibration, gauge inspection and short‑range dimensional checks in metrology environments. Is traceability or calibration included with the product? The product is supplied as a matched pair; specific calibration certificates are provided only if stated in the product listing for that article. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
15 mm Gauge Pin, Single, 50 mm Length, Workshop Version - Metav IndustryLine
Take advantage of precise industrial tolerances and a compact workshop design for consistent end measurements; the combination of ±0.002 mm accuracy and special steel construction ensures reliable reference values in assembly and testing operations — order via Metav Werkzeuge or consult the sales team for application advice. Test pin M323.F00 — single gauge pin, 15.00 mm diameter, 50 mm length (Metav IndustryLine) The Test pin M323.F00 serves as a compact reference probe for end measurements and fixture checks in workshop environments, supplied as a single precision pin suitable for bench or jig use. 15.00 mm diameter for precise end measurements 50 mm compact working length Tolerance ±0.002 mm industrial precision Workshop-grade special steel construction Accurate reference values that reduce rework and uncertainty The solid cylindrical design provides a stable reference for end-measurement tasks where repeatability matters. With a stated tolerance of ±0.002 mm, this pin delivers industrial-grade dimensional control that supports quality assurance processes and reduces the need for rework. The moderate mass and balanced geometry help maintain contact consistency during manual or fixture-based measurements, contributing to reproducible results in serial inspection and bench testing. Compact form and robust material for everyday workshop use A length of 50 mm and a nominal diameter of 15.00 mm keep handling simple while allowing use in confined setups and measurement fixtures. The special steel construction offers a durable contact surface that resists wear under routine use in production and inspection environments. The single-pin format permits targeted checks and makes the component easy to store and replace within a tooling kit, ensuring minimal downtime when references are required. Clear identification and integration into inspection workflows Traceability is supported by the product identifiers SKU M323.F00 and GTIN 4061905067389, simplifying inventory and document control. The workshop-oriented finish and compact dimensions mean the pin integrates readily into existing jigs and gauges as a reference element for end-measurements. Suppliers such as Metav IndustryLine combine broad distribution with a service approach that helps workshops source precision components without compromising on supply reliability. For dependable end-measurement references, request the Metav IndustryLine test pin via Metav Werkzeuge — contact the team for specification matching or ordering assistance at info@metav-werkzeuge.com or by phone on +49 2822 7131930 Technical data SKU: M323.F00 GTIN: 4061905067389 Category: Gauge pin / Test pin Facts Diameter: 15.00 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.1 kg Special features Material: Special steel Version: Workshop execution Single test pin Application hint: End measurements FAQ What level of accuracy does the test pin provide? The test pin is specified with a tolerance of ±0.002 mm, offering industrial precision suitable for reference and inspection tasks. Which materials is the pin made from? The probe is manufactured from special steel, chosen for wear resistance and dimensional stability under regular workshop use. Is this pin suitable for fixture or jig applications? Yes, the compact 50 mm length and standard 15.00 mm diameter make the pin suitable as a reference element in fixtures and jigs for end-measurements. How is the product identified for inventory control? Identification is provided by SKU M323.F00 and GTIN 4061905067389, which assist with ordering and documentation. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
15 mm Limit Plug Gauge H7 DIN 2245 Hardened Gauge Steel - Metav IndustryLine
Take advantage of the combination of DIN 2245 compliance, hardened gauge steel construction and an H7 tolerance for reliable bore acceptance checks; order the limit plug gauge directly via Metav Werkzeuge or contact our advisors for application-specific guidance. Limit plug gauge, 15.00 mm, DIN 2245 H7 — Metav IndustryLine, hardened gauge steel The Limit plug gauge, 15.00 mm DIN 2245 H7 is a compact go/no-go verification gauge for fast, repeatable assessment of bore diameters in production and inspection. DIN 2245 H7 tolerance fit Hardened gauge steel construction Precise 15.00 mm diameter verification Compact go/no-go inspection tool Accurate acceptance testing that saves production time The limit plug gauge is designed for quick verification of bores to the H7 tolerance class under DIN 2245, turning a complex inspection into a single, reliable step. Because the gauge is manufactured from hardened gauge steel, the tool resists wear in routine use, maintaining precision and reducing the need for frequent replacments. The resulting benefit is a measurable cut in inspection time and fewer false rejections during quality control, supporting smoother production workflows and higher first-pass yield. Robust construction for consistent results on the shop floor Manufactured from hardened gauge steel, the gauge delivers stable performance even when used repeatedly in machine shops and inspection benches. The go/no-go principle provides immediate, unambiguous results: a go fit confirms conformity to the nominal 15.00 mm bore with the H7 tolerance, while a no-go indicates deviation. This simplicity reduces operator interpretation and increases repeatability, which is particularly valuable for batch inspections or in-line quality checks where speed and clarity are essential. Integration into inspection routines and traceability The plug gauge is suitable for direct use in dimensional control routines and as a first-line acceptance check prior to downstream assembly. Marking and the supplied article identifiers allow straightforward logging of inspection events; recorded checks improve process documentation and support traceability. For operations that require formal certification trails, Metav Werkzeuge can advise on calibration and documentation strategies that keep inspection records consistent with internal quality systems. For a reliable inspection routine based on DIN 2245 tolerance checking, request the Metav IndustryLine limit plug gauge from Metav Werkzeuge for expert advice and dependable delivery from Emmerich. Technical Data Article number: M314.015 GTIN: 4054469121444 Norm: DIN 2245 Diameter: 15 mm Facts EClass: 21170218 Customs tariff number: 90173000 SKU: M314.015 Special features Material: gauge steel, hardened Category: Messstifte; Lehren Label: Grenzlehrdorn, 15,0 mm DIN 2245/H7; 0,07 kg Condition: good FAQ What is the intended use of this limit plug gauge? The limit plug gauge is intended for quick go/no-go checking of bore diameters to H7 tolerance, providing a fast conformity check for production and inspection tasks. How does the gauge indicate acceptance or rejection? A successful fit (go) with the 15.00 mm plug confirms the bore meets the H7 limit; a no-go condition signals that the bore exceeds the allowed deviation and requires further evaluation. Is the gauge suitable for high-volume shop use? Yes, the hardened construction and simple go/no-go operation make the gauge suitable for repeated use in the shop floor environment where speed and repeatability matter. Can the gauge be included in calibration records? The plug gauge can be included in calibration and inspection logs; Metav Werkzeuge can advise on calibration intervals and documentation to match internal quality procedures. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
15 mm Limit Plug Gauge With Wear Allowance, Hardened Steel, DIN 7162 - Filetta
Benefit from a hardened-steel construction, conformity to DIN 7162 and a defined wear allowance on the GO side for dependable dimensional control; order the limit gauge pin directly via Metav Werkzeuge or consult our specialists for application advice. Limit gauge pin MS911.219 — 15 mm hardened-steel limit gauge to DIN 7162 by Filetta The Limit gauge pin MS911.219 is a precision limit gauge pin intended for quick GO/NO‑GO verification and repeatable dimensional checks in production and inspection routines. Hardened steel for stable measurement Conforms to DIN 7162 standard Wear allowance on the GO side Precision 15 mm gauge diameter Consistent conformity for routine inspection A hardened, standardised limit gauge offers a straightforward method to verify part dimensions with minimal interpretation. The MS911.219 is made from hardened steel, ensuring surface durability and stable contact geometry during repeated use. Conformity with DIN 7162 provides an objective reference that supports quality control documentation and helps to reduce false rejections. For workshop environments and inspection benches where speed and clarity are essential, a limit gauge pin delivers a direct binary check that complements more elaborate measuring systems. Robust construction for repeatable results Durability and repeatability are primary considerations for shop-floor gauges. The chosen material and heat treatment yield a contact surface that resists deformation, so checks remain reliable over long production runs. The documented wear allowance on the GO side compensates for gradual surface wear and preserves the intended acceptance criteria; this feature extends service life and maintains measurement integrity between maintenance intervals. As a compact verification tool, the pin requires no auxiliary power and offers an efficient way to protect throughput without adding complexity. Easy integration into inspection workflows Limit gauge pins are inherently low‑complexity instruments that integrate well into production flow, in-line checks and final inspection stages. The compact 15 mm diameter simplifies handling and storage while allowing quick GO/NO‑GO trials at several positions on a component. When used alongside calibrated measurement procedures, these gauges contribute to faster decision-making and fewer production stoppages. Clear marking and standard conformity aid traceability in quality records and make these pins suitable for routine use in mechanical workshops and inspection departments. Practical advantages for purchasing and maintenance Standardised gauges such as this reduce training overhead because their purpose and limits are unambiguous. The solid construction cuts maintenance intervals and the wear allowance on the GO side postpones replacement until a defined criterion is reached, lowering total lifecycle costs. For companies that standardise workbenches, limit gauge pins offer a cost‑effective supplement to calipers and micrometres, serving as quick acceptance checks that keep assembly and machining processes moving. Contact Metav Werkzeuge for technical guidance on integrating the Filetta limit gauge pin MS911.219 into existing inspection routines or to arrange prompt delivery from Emmerich — eMail info@metav-werkzeuge.com or call +49 2822 7131930 Technical Data Article number: MS911.219 Model: MS911.219 Standard: DIN 7162 Facts Diameter: 15 mm Special features Material: hardened steel Feature: wear allowance on the GO side Category: gauge pins / test pins FAQ What inspection tasks suit this type of gauge? Limit gauge pins are intended for quick GO/NO‑GO checks and the MS911.219 by Filetta is well suited to routine diameter verification and reproducible bench checks. Is the MS911.219 suitable for continuous shop‑floor use? Yes, the hardened-steel construction and the specified wear allowance on the GO side make the Filetta MS911.219 appropriate for frequent use in production environments. Does this gauge conform to any standard? The Filetta limit gauge pin MS911.219 is supplied to DIN 7162, enabling consistent acceptance criteria and straightforward traceability in quality documentation. Manufacturer / Responsible: Schut Geometrische Meettechniek bv; Duinkerkenstraat 21; 9723 BN Groningen; The Netherlands; +31 50 5877877; schutnl@schut.com
15 mm Limit Plug Gauge, Wear Allowance On Go Side, Hardened Steel, DIN 7162 - Filetta
Benefit from the combination of hardened steel construction and conformity to DIN 7162 for repeatable internal diameter checks; the 15 mm nominal size offers a direct fit for standard bores. Order the limit plug gauge directly via Metav Werkzeuge or consult our specialists for application advice. Limit plug gauge – 15 mm, hardened steel (Filetta) Limit plug gauge for quick go/no-go verification of internal diameters in production and inspection Hardened steel construction Compliant with DIN 7162 standard 15 mm nominal diameter gauge Wear allowance on master side Precision inspection where it matters The limit plug gauge is designed for fast and reliable verification of internal bores in routine quality checks. Manufactured from hardened steel, the gauge offers mechanical resilience that reduces wear and maintains form under repeated use. Conformity with DIN 7162 ensures that the gauge fits established acceptance procedures and inspection protocols, simplifying integration into existing quality workflows. As a result, production lines gain a compact, low-effort control tool that supports consistent pass/fail decisions. Durability and traceable performance A clear technical advantage of this gauge is the incorporated wear allowance on the master side, which prolongs usable life and offers predictable wear behaviour. The material choice—hardened steel—provides resistance to deformation and abrasion, reducing dimensional drift during frequent checks. For workshops and inspection rooms that require robust tools rather than disposable checking aids, this construction translates into fewer replacements and stable measurement outcomes over time, supporting reliable component acceptance. Simple handling for reliable results The gauge’s nominal 15 mm size and compact form factor make it suitable for rapid in-process checks and bench inspection tasks in metalworking and assembly. As a limit gauge, it provides unambiguous go/no-go feedback without needing additional measurement devices, speeding up throughput while keeping control simple. The Filetta item (Article number MS911.177) is particularly suited to operators who prioritise straightforward inspection methods and durable tooling that aligns with recognised standards. For reliable acceptance testing and long-term workshop use, request the Filetta limit plug gauge from Metav Werkzeuge—technical advice and supply are available via info@metav-werkzeuge.com or by phone on +49 2822 7131930 Technical data Article number: MS911.177 Name: Limit plug gauge Brand: Filetta Facts Diameter: 15 mm Standard: DIN 7162 Special features Material: hardened steel Application: internal diameter verification (plug gauge) Special feature: wear allowance on master side Category: Gauges (Measuring instruments > Gauges) FAQ What is the intended use of this limit plug gauge? The limit plug gauge is intended for go/no-go checks of internal diameters in production and inspection; the Filetta gauge MS911.177 verifies whether bores meet the specified acceptance limits. Is the gauge suitable for continuous shop-floor use? Yes, the hardened steel construction of the Filetta limit plug gauge ensures robustness for frequent shop-floor inspections and routine quality control. Which standard does the gauge conform to? The gauge conforms to DIN 7162, meaning it fits standard inspection routines and documented acceptance criteria for plug gauges. Manufacturer / Responsible: Schut Geometrische Meettechniek bv; Duinkerkenstraat 21; 9723 BN Groningen; The Netherlands; +31 50 5877877; schutnl@schut.com
15 mm Setting Ring Form C, Hardened Gauge Steel, DIN 2250/DIN 286 JS3 - Metav IndustryLine
Combine the precise tolerance class DIN 2250 / DIN 286 (JS 3) with a hardened, lapped gauge steel finish and Form C geometry to secure reproducible reference diameters in inspection and set-up tasks. Order the setting ring directly via Metav Werkzeuge or consult our specialists for application advice. Setting ring 15 mm (M313.015) — DIN 2250, hardened gauge steel — Metav IndustryLine The Setting ring 15 mm (M313.015) is a precision gauge ring designed for reliable diameter references in inspection, calibration and tool-room set‑ups. DIN 2250 / DIN 286 JS 3 tolerance Hardened and lapped gauge steel Form C geometry for stable seating GTIN 4054469120539 for traceability Faster, verifiable set-ups through standardised tolerances A clearly specified tolerance system reduces ambiguity during machine set-up and inspection. Built to DIN 2250 and DIN 286 with JS 3 tolerance grading, this ring provides a documented reference diameter that supports repeatable workflows and consistent pass/fail decisions. The formal standardisation shortens measurement uncertainty assessment and simplifies integration into quality plans, which translates into fewer set‑up iterations and reduced machine downtime. Durable construction that preserves accuracy over time Manufactured from hardened, lapped gauge steel, the ring resists wear while maintaining its calibrated profile. The lapped finish reduces surface irregularities and helps preserve the contact geometry under repeated use, so reference dimensions remain stable across inspection cycles. For workshop and shop‑floor environments this means longer intervals between replacement and a lower risk of drift-induced rejects, improving throughput without sacrificing precision. Form C shape for stable seating and repeatable results The Form C configuration delivers defined seating that minimises rocking and eccentricity when used with fixtures or plug gauges. This geometry assists in achieving consistent contact lines during measurement or during the setting of master gauges, yielding improved repeatability. Where component alignment and centring are critical, the shaped bearing face reduces setup variation and contributes directly to tighter process control. Seamless integration into quality systems and inventory control The ring is provided with clear identification (SKU M313.015 and GTIN 4054469120539), facilitating traceability in inspection records and stock management. As a compact, standards‑based reference, it fits naturally into gauge sets, calibration benches and inspection jigs, supporting both routine checks and documented verification procedures. The combination of normative conformity and durable material offers a pragmatic balance of longevity and metrological reliability for production and maintenance applications. Contact Metav Werkzeuge for tailored gauge sets, compatibility advice or to discuss matching ring standards — telephone +49 2822 7131930 or e-mail info@metav-werkzeuge.com Technical data Article number: M313.015 Manufacturer: Metav IndustryLine GTIN: 4054469120539 Eclass: 21170104 Facts Diameter: 15 mm TARIC / Commodity code: 90173000 Standards: DIN 2250; DIN 286; JS 3 Special features Material: hardened and lapped gauge steel Geometry: Form C Categories: Gauges; Setting rings FAQ What tolerance class does this ring meet? The setting ring meets the tolerances described in DIN 2250 and DIN 286 with a JS 3 grading, providing a reproducible reference for inspection and set‑up activities. What material and finish are used? The M313.015 is made from hardened gauge steel with a lapped finish, chosen to combine wear resistance with a stable contact surface for long‑term accuracy. How does the Form C design help in practical use? Form C gives a defined seating face that reduces rocking and eccentricity, improving repeatability when the ring is used in fixtures, plug gauge assemblies or calibration benches. How can the ring be identified in stock and documentation? Identification is via SKU M313.015 and GTIN 4054469120539, which supports traceability in inventory systems and inspection records. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
15-16mm Gauge Pin Set 101pcs 0.01mm Increment With Probe Holder In Plastic Case - Metav IndustryLine
The combination of high incremental precision, robust special steel construction and organised transport storage makes this gauge pin set a practical choice for repeatable size checks and assembly control. Order the gauge pin set directly via Metav Werkzeuge or ask our consultants if needed. Gauge pin set M318.585 — 15.00–16.00 mm, 0.01 mm step (Metav IndustryLine) Gauge pin set M318.585 is a precision inspection kit for verifying bore diameters and fit tolerances in production and inspection environments. 101-piece precision set Range 15.00–16.00 mm 0.01 mm step accuracy Supplied in transport case Accurate size control for fast, reliable inspection This precision pin collection is designed for incremental checking across the 15.00–16.00 mm range with 0.01 mm steps, enabling fine gradation when assessing bore sizes and clearance fits. The specified performance includes an indicated accuracy of 0.004 mm, which supports tight tolerancing in workshop quality control. Using a stepped set reduces setup time for sequential inspections and simplifies pass/fail decisions during series production, while the 50 mm pin length provides a stable seating depth for standard bore checks. Durable design and tidy workshop storage Constructed from special steel, the pins resist everyday wear and keep dimensional stability across repeated use. The set includes a pin holder that aids handling during measurement tasks and prevents accidental damage when selecting pieces. Delivery in a dedicated transport case protects the pins during movement between workstations and keeps the 101 items organised for quick retrieval. The overall kit weight of 10.7 kg reflects the solid construction and the professional nature of the set, suitable for busy machine shops and inspection benches. Practical applications in manufacturing and inspection This set is tailored for use in mechanical engineering, toolrooms and assembly control where dimensional conformity is critical. The fine 0.01 mm increment is particularly useful when matching fits or checking progressive machining steps. As a compact gauge solution, it supports repeatable checks without complex measuring devices, making routine in-process control faster and less error-prone. The collection’s format also suits use alongside coordinate measuring equipment for rapid pre-checks before more elaborate inspection procedures. Contact Metav Werkzeuge today for supply details and mention M318.585 to ensure rapid handling from Emmerich Technical data Article number: M318.585 GTIN: 4054469156224 Customs tariff number: 90173000 Facts Pieces per set: 101 Measurement range: 15.00–16.00 mm Increment / step: 0.01 mm Pin length: 50 mm Accuracy: 0.004 mm Weight: 10.7 kg Special features Material: special steel With pin holder Supplied in transport case Category: gauge pins Set design for sequential bore checks FAQ What is the intended use for this gauge pin set? The gauge pin set M318.585 is intended for checking bore diameters, verifying assembly fits and performing rapid in-process pass/fail inspections in workshops and production lines. How fine are the steps and how does that help inspection? Steps of 0.01 mm allow fine-grained assessment of bore sizes; the 0.01 mm increment in this M318.585 set makes it easier to identify incremental deviations during progressive machining or assembly. Is the set delivered with a calibration certificate? The M318.585 set is supplied in a transport case; it is not provided with an ISO 17025 calibration certificate unless explicitly labelled as calibrated on the product listing. What material are the pins made from and how durable are they? Pins are manufactured from special steel, offering durable performance for routine workshop use and helping to maintain dimensional stability over many inspection cycles. Can this set be used for serial production checks? Yes, the organised layout and fine increments of the M318.585 set support rapid, repeatable checks suitable for serial production and incoming inspection tasks. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
15.01mm Gauge Pin Length 50mm Workshop Finish - Metav IndustryLine
Compact inspection pin combining 15.01 mm diameter, 50 mm length and a tight ±0.002 mm tolerance for dependable reference measurements; robust special steel construction ensures long service life in workshop environments. Order the gauge pin directly via Metav Werkzeuge or consult the Metav specialists for technical guidance. Gauge pin, single M323.F01 – Ø 15.01 mm, 50 mm length (Metav IndustryLine) The gauge pin, single 15.01 mm, 50 mm is a hardened inspection pin for precise end‑measurement and reference checks in metrology benches and workshop quality control. Workshop-grade construction for daily use Diameter 15.01 mm with ±0.002 mm tolerance 50 mm hardened special-steel pin Single-piece design, traceable GTIN 4061905067396 Accurate reference for inspection and calibration As a compact reference element, the M323.F01 provides consistently reproducible contact points for go/no‑go checks and end‑measurements. The defined 15.01 mm diameter combined with a ±0.002 mm manufacturing tolerance reduces measurement uncertainty and supports repeatable results on gauges, comparators and fixture checks. This level of accuracy is particularly suitable where small deviations can affect assembly fits or functional clearances; the pin therefore serves as a reliable master for routine inspection routines and short‑run quality control. Built for workshop durability and handling comfort The pin is formed from special steel and finished in a workshop‑grade execution to withstand repeated use. A 50 mm shank length ensures stable seating in inspection fixtures while remaining easy to handle during frequent checks. The single‑piece design minimises potential play between components and simplifies storage and handling in a busy production environment. These attributes translate into less downtime for replacements and a reduced risk of damage-induced measurement drift, supporting continuous production flows. Traceability and straightforward integration into inspection workflows Marked by GTIN and article references, the component is ready for catalogue integration and inventory control; traceability supports quality documentation and audit trails. The compact geometry allows rapid use with depth gauges, micrometers and comparator setups, making it a practical choice for machine shops and quality labs that require fast, repeatable comparative measurements. For specific fixture compatibility or batch requirements Metav Werkzeuge can advise on matching reference tools and supply logistics. Contact Metav Werkzeuge for advice on specifying the M323.F01 gauge pin and to arrange supply direct from Emmerich for reliable delivery and quality assurance Technical data Article number: M323.F01 GTIN: 4061905067396 eClass: 21170231 Label: Gauge pin, single, 15.01 mm × 50 mm Facts Diameter: 15.01 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.1 kg Special features Material: Special steel Version: Workshop execution Supply: Single gauge pin Accuracy class: ±0.002 FAQ What tolerance does the pin provide? The pin is manufactured to a tolerance of ±0.002 mm, which makes the M323.F01 suitable for reference and inspection tasks requiring tight dimensional control. Which materials can be inspected with this pin? The gauge pin itself is made from special steel; it is intended as a dimensional reference and is suitable for use with components made of common workshop materials when used as a master or checking element. How is the item supplied? The product is supplied as a single gauge pin under article number M323.F01 and can be ordered with GTIN 4061905067396 for inventory purposes. Can this pin be used in fixture checks and comparator setups? Yes, the compact geometry and precise diameter make it well suited for comparator seating, fixture alignment and go/no‑go reference checks in workshop and inspection stations. Is the part traceable for quality documentation? Traceability is supported via the GTIN and article number; Metav IndustryLine documentation can be provided to assist with quality records and inventory tracking. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
15.02mm Test Pin, Single, 50mm Length, Workshop Version - Metav IndustryLine
Take advantage of the workshop‑grade robustness, ±0.002 mm tolerance and compact 50 mm measuring length for repeatable end‑dimension checks; order directly via Metav Werkzeuge or consult our specialists for application advice. Gauge pin, single — 15.02 mm diameter, 50 mm length (Metav IndustryLine M323.F02) The gauge pin, single, 15.02 mm diameter, 50 mm length is a workshop‑grade inspection pin designed for precise end‑dimension verification and fixture checking in production and assembly environments. Workshop version for daily use Nominal diameter 15.02 mm ±0.002 mm Compact 50 mm measuring length Supplied in a transport case Reliable dimensional control for rapid inspection This compact gauge pin is specified for consistent end‑dimension checks where short, repeatable measurements are required. With a nominal diameter of 15.02 mm and a documented deviation of ±0.002 mm, the pin supports fine tolerance verification during incoming inspection, fixture set‑up and spot checks on the shop floor. The precision tolerance reduces uncertainty in pass/fail decisions and shortens inspection cycles, delivering measurable efficiency gains in routine quality control. Material choice and mechanical durability Constructed from special steel in a workshop configuration, the measuring pin combines mechanical stability with wear resistance suitable for repeated contact checks. The solid construction and balanced mass (approx. 0.1 kg) make the pin easy to locate and position while resisting the deformation that can compromise short‑length measurements. This material selection prioritises longevity and keeps replacement intervals low, which supports predictable maintenance planning in production environments. Designed for handling and safe storage At 50 mm overall length the pin is compact enough for quick one‑hand placement yet long enough to reach recessed features in many assemblies. The supplied transport case protects the pin during storage and transit and helps maintain the measuring surface condition between uses. The workshop execution emphasises practical aspects: robust handling, clear identification and straightforward storage to keep inspection routines swift and reliable. Fits into established inspection workflows The M323.F02 measuring pin is suitable as a standardised reference for end‑measure checks and fixture validation; it integrates easily into existing inspection jigs and comparative gauges. Labelling and SKU traceability support inventory control and process documentation, while the straightforward geometry minimises operator training. As part of Metav IndustryLine, this measuring pin benefits from the manufacturer’s focus on accessible precision and consistent supply for industrial customers. For dependable end‑dimension verification, request the M323.F02 from Metav Werkzeuge in Emmerich or contact our consultants for tailored application guidance Technical data SKU: M323.F02 GTIN: 4061905067402 Description: Gauge pin, single, 15.02 mm diameter, 50 mm length Manufacturer: Metav IndustryLine Facts Diameter: 15.02 mm Length: 50 mm Tolerance / deviation: ±0.002 mm Weight: 0.1 kg Special features Workshop version Material: special steel Supplied in a transport case Category: Gauge pins (Messstifte) FAQ What is the measurement tolerance of this gauge pin? The M323.F02 gauge pin is manufactured to a deviation of ±0.002 mm, making it suitable for fine tolerance end‑dimension checks. How is the pin delivered and stored? The Metav IndustryLine pin is supplied in a transport case to protect the measuring surfaces during storage and transport. What applications is this measuring pin intended for? This inspection pin is intended for end‑dimension verification, fixture checking and short‑range reference measurements in production and assembly workflows. How can the product be identified for reordering? Reference the SKU M323.F02 or the GTIN 4061905067402 when reordering the Metav IndustryLine gauge pin. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
15.03mm Gauge Pin, Single, 50mm Length, Workshop Version - Metav IndustryLine
The combination of ±0.002 mm repeatability, 15.03 mm diameter and robust special steel construction ensures reliable end‑measure checks in workshop environments; order the gauge pin directly via Metav Werkzeuge or consult Metav's specialists for integration advice. Gauge pin, single, 15.03 mm — 50 mm length (Metav IndustryLine, workshop version) A gauge pin, single, 15.03 mm (length 50 mm) designed for precise end‑measure control and go/no‑go checking in production and maintenance settings. Workshop version for everyday use Diameter 15.03 mm for end‑measure checks Tolerance ±0.002 mm for high repeatability 50 mm overall length with sturdy construction Precision that protects quality and reduces rework This gauge pin delivers ±0.002 mm dimensional fidelity, providing a measurable improvement in inspection consistency compared with coarse gauges. The pin's nominal diameter of 15.03 mm is matched to tight tolerances, making it suitable for final checks, alignment tasks and calibration routines where even small deviations lead to costly rework. Thanks to the compact length of 50 mm, the probe is simple to handle while still offering enough engagement for reliable go/no‑go assessments; the result is a faster quality loop and fewer scrapped parts. Durable material and workshop suitability Manufactured from special steel, the probe combines surface hardness with resistance to wear in routine shop use. The Workshop version construction focuses on robustness: contact faces are ground for repeatable seating and the body resists damage from incidental knocks and handling. This material choice maintains a stable diameter over time, so measurement drift is minimised and replacement intervals are extended—an economical choice for busy inspection benches and on‑machine checks. Practical use and integration into inspection workflows The pin is sized for direct insertion checks and end‑dimension verification in fixtures and nests, and it fits common pin holders and gauge sets. Its compact form facilitates handheld verification as well as use in jigs when a quick go/no‑go decision is required. By standardising on a repeatable gauge with a declared tolerance, inspection protocols become more defensible and traceable—improving audit readiness and production confidence. The combination of robustness and precision supports lean workflows and reduces stoppages due to ambiguous measurements. Discuss integration with Metav Werkzeuge for tailored inspection solutions — Metav IndustryLine items like this gauge pin (SKU M323.F03) can be specified for production or maintenance work; email info@metav-werkzeuge.com or call +49 2822 7131930 to arrange technical alignment Technical data Article number: M323.F03 GTIN: 4061905067419 Manufacturer: Metav IndustryLine Facts Diameter: 15.03 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.1 kg ECLASS: 21170231 Special features Material: special steel Workshop version (robust construction) Single gauge pin for end‑measure checking Story trigger: end measures (endmasse) FAQ Is this gauge pin suitable for go/no‑go checks on shafts and bores? Yes. The Metav IndustryLine gauge pin (SKU M323.F03) with 15.03 mm diameter and ±0.002 mm tolerance is intended for go/no‑go and end‑measure verification on shafts, bores and mating features. Can the pin be used for repeated in‑machine checks? Repeated checks are feasible; the gauge pin's special steel construction and workshop specification are chosen to withstand routine handling and in‑machine use while maintaining dimensional stability. How is the accuracy specified verified? The declared ±0.002 mm tolerance is the manufacturing specification for the gauge pin. For traceable calibration certificates or batch verification, Metav Werkzeuge can advise on available calibration services and documentation. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
Fast, tactile checks where electronics are impractical
Gauges and test pins provide unequivocal go/no-go results for threads, bores, gaps and radii without relying on electronics. The range covers plug gauges and ring gauges for internal and external threads, feeler gauges and precision feeler strips for micro‑gap assessment, plus probe pins and measuring pins for tactile diameter and pitch checks.
How these tools work in the production environment
Mechanical gauges operate as direct reference standards: a plug gauge or ring gauge verifies conformity to thread profiles and mating ability, while limit gauges separate accept from reject in a single step. Test pins are used to tactilely measure small bore diameters, centre‑to‑centre distances and radii. Manufactured from hardened gauge steel or ceramic and often precision lapped, these instruments deliver immediate physical results that are ideal for incoming inspection, machine‑side checks and final control.
Measurable benefits that affect production performance
- Reduced scrap and rework through rapid, unambiguous pass/fail assessment.
- Increased repeatability thanks to very low measurement uncertainty and fine lapping.
- Lower downtime: quick checks at the machine save cycle time and reduce setup periods.
- Durable construction with high wear resistance from specialised, low‑distortion alloys.
- Versatile delivery formats: individual gauges, organised sets in wooden cases or metre‑length feeler rolls compliant with DIN 2269.
Why Metav is the practical choice for precision supplies
Metav combines decades of expertise with a broad warehouse and quality filtering from Emmerich. As a precision partner for industry, craft and trade, Metav supplies a comprehensive selection of gauges and test pins alongside complementary tools such as precision calipers and setting rings. With over 48,000 customers and a catalogue exceeding 250,000 items, Metav is positioned to supply reliably, reduce vendor complexity and support traceable quality control to national standards.
Summary
Gauges and test pins are indispensable for dependable, repeatable quality assurance where tactile, mechanical verification is preferred. Choose these plug gauges, ring gauges, feeler strips and probe pins when immediate, robust measurement decisions are required on the shop floor.
FAQ
What materials are gauges and test pins typically made from?
Gauges and test pins are usually manufactured from hardened gauge steel for durability and wear resistance; ceramic variants are available where thermal stability and minimal wear are critical.
How do thread gauges ensure mating capability?
Thread plug gauges and ring gauges check flank diameters and thread form against standards, providing a clear go/no‑go verdict that confirms pairability with mating parts.
Which tolerance class should I choose for probe pins and gauge sets?
Select tolerance classes aligned with your inspection requirements; for high‑precision tasks, sets produced to DIN 2269 or equivalent tolerance classes ensure micrometre‑level control and repeatability.
Can feeler gauges measure contact gaps in valve and engine work reliably?
Yes. Feeler gauges and precision feeler strips, supplied either as a fan or metre‑length rolls, allow accurate assessment of valve clearances and contact gaps down to micrometre increments.
How do limit gauges speed up in‑process inspection?
Limit gauges separate good from bad in a single, tactile operation, enabling rapid go/no‑go checks at the machine and reducing both inspection time and the likelihood of human interpretation errors.
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com