Precision gauge blocks and plug gauges for reliable dimensional control
Mechanical gauge blocks and plug gauges are essential for tactile verification of threads, bores and gap dimensions, providing fast, unambiguous go/no-go results that enhance process reliability and reduce scrap. Designed for industrial metalworking and toolmaking, these precision tools support incoming inspection and final quality checks by delivering traceable measurements in applications such as thread inspection, bore diameter testing and spacing checks. Manufactured from specially hardened, low-distortion alloys and fine-lapped for minimal measurement uncertainty, the range includes thread plug gauges, precision plug gauges and calibration gauge blocks to ensure long-term repeatability and wear resistance.
15.29mm Gauge Pin 50mm Length Workshop Version - Metav IndustryLine
Combine precise ±0.002 mm repeatability, robust special steel construction and a compact 15.29 mm diameter with a 50 mm overall length for dependable reference measurements; order this gauge pin via Metav Werkzeuge or consult the in‑house specialists for application advice. Gauge pin M323.F29 — Precision gauge pin, 15.29 mm diameter, 50 mm length (Metav IndustryLine) A gauge pin M323.F29 engineered as a dimensional reference for inspection and end‑measurement tasks, offering stable contact geometry in workshop environments. High‑precision tolerance ±0.002 mm Special steel construction for wear resistance 50 mm overall length for standard inspection use Dependable reference for dimensional control A compact measuring reference such as this gauge pin supplies a clear measurement basis when verifying bores, pins and alignment features. The 15.29 mm diameter and the notified ±0.002 mm tolerance translate into a quantifiable limit for acceptance testing and go/no‑go checks, reducing ambiguity during quality control. The solid contact geometry provides repeatable seating in gauges and fixtures, which improves throughput by cutting down rework cycles and inspection uncertainty. Built for workshop handling and traceability Constructed from special steel, the pin is resilient against routine handling and exhibits good wear resistance in standard workshop use. The 50 mm overall length gives a practical working reach while maintaining stiffness for accurate contact. Delivered in a protective box for safe transport and storage, the item arrives ready for immediate integration into inspection benches or fixture sets. This workshop‑spec design supports regular shop routines without the need for special handling equipment. Practical integration into inspection routines As a compact inspection aid, the pin functions as a clear dimensional standard for end‑measurement setups and fixture alignment. The compact mass and balanced dimensions (approx. 0.1 kg) make mounting and swapping straightforward during serial checks. Coupling this reference element with existing gauges or dedicated holders yields an efficient inspection step that can be repeated across batches to track process stability and reduce scrap rates. Contact Metav Werkzeuge today to discuss suitability for specific inspection tasks and to order the Metav IndustryLine gauge pin M323.F29 with protective packaging or alternative sizes for broader measurement coverage. Technical data Article number: M323.F29 GTIN: 4061905067808 Manufacturer: Metav IndustryLine Weight: 0.1 kg Material: Special steel Category: Gauge pin / test pin Workshop version Protective box for transport included Facts Diameter: 15.29 mm Length: 50 mm Tolerance: ±0.002 mm Special features Delivered in protective box for transport Robust contact geometry for repeatable seating Intended for inspection and end‑measurement applications FAQ What is the primary use of this gauge pin? The gauge pin M323.F29 serves as a precision reference for bore checks, pin sizing and fixture alignment during inspection tasks. Is the material specified for long‑term workshop use? Yes, the pin is made from special steel that provides good wear resistance for routine inspection handling. Does the delivery include protective packaging? The gauge pin is supplied in a protective box to ensure safe transport and to reduce the risk of damage prior to use. What tolerance can be expected during inspection? The product is specified with a tolerance of ±0.002 mm, suitable for high‑accuracy reference checks in workshop environments. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
15.2mm Gauge Pin, Single, 50mm Length, Workshop Version - Metav IndustryLine
Take advantage of precise dimensional control and consistent fit checks thanks to the combination of a 15.20 mm nominal diameter, a tight ±0.002 mm tolerance and a robust 50 mm working length; order the item directly via Metav Werkzeuge or request assistance from our consultants for integration into inspection plans. M323.F20 test pin — 15.20 mm diameter, 50 mm length (Metav IndustryLine) The M323.F20 test pin is a workshop‑grade gauge pin designed for end‑measure checks and bore verification in production and quality control environments. 15.20 mm ground diameter for precise fits 50 mm working length for secure handling Special steel for dimensional stability Tolerance ±0.002 mm for reliable checking Accurate fit control for interchangeable parts This gauge pin delivers a measurable improvement in process reliability through a 15.20 mm nominal diameter combined with a ±0.002 mm manufacturing tolerance. Such accuracy supports repeatable verification of bores and mating features, which reduces assembly rework and scrap. The result is a straightforward quality assurance metric: a single, traceable dimension that confirms part conformity and helps maintain production flow. Workshop-friendly design that speeds inspection The 50 mm length provides secure handling during routine checks while remaining compact enough for bench and in‑line use. The workshop‑grade execution balances robustness with ease of use: the pin is supplied as a single item for flexible deployment across fixtures, go/no‑go sets or ad‑hoc measurement tasks. Dimensional stability of the special steel material ensures that routine contact checks do not rapidly alter the reference size, supporting consistent results across multiple stations. Practical applications and traceability for quality systems Intended primarily for end measurements and bore checks, the pin suits final inspection, first article verification and process control sampling. The product is identifiable via GTIN for inventory control and traceability in quality documentation, enabling clear linking between measurement results and supplied items. As a house brand from Metav IndustryLine, the component fits into larger gauge systems or can be used independently where an exact reference surface is required. Contact Metav Werkzeuge for tailored gauge set recommendations and technical advice on the Metav IndustryLine M323.F20 test pin, available for prompt supply from Emmerich. Technical data Article number: M323.F20 GTIN: 4061905070303 Brand: Metav IndustryLine Category: Gauge pin Supply: single piece Facts Diameter: 15.20 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.1 kg Special features Material: Special steel Workshop‑grade execution Intended for end measurements and bore checks Single item supply for flexible use FAQ What is the nominal size and tolerance of this gauge pin? The M323.F20 test pin features a nominal diameter of 15.20 mm with a manufacturing tolerance of ±0.002 mm, providing a reliable reference for precision checking. Which measurement tasks is this component suited for? This gauge pin is intended for end‑measure checks and bore verification, making it suitable for first article inspection, assembly checks and routine process control. What material is the pin made from and why does that matter? The pin is made from special steel, which offers dimensional stability and wear resistance under repeated contact, helping to preserve the reference size over many inspection cycles. Is calibration supplied with this item? No specific calibration certificate is indicated for this listing; certified calibration can be arranged separately to meet internal quality system requirements. Can the pin be integrated into existing gauge sets or fixtures? Yes. Supplied as a single item, the pin is suitable for incorporation into gauge sets, fixtures or handheld inspection routines where a precise reference diameter is required. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
15.31mm Gauge Pin Length 50mm Workshop Finish - Metav IndustryLine
Precise workshop gauge pin in special steel with a nominal diameter of 15.31 mm and a length of 50 mm delivers repeatable end‑measurement results; its tight ±0.002 mm tolerance supports fine control in inspection tasks and the protective transport case preserves accuracy. Order directly via Metav Werkzeuge or contact a consultant for application advice. Gauge pin, single, 15.31 mm diameter, 50 mm length — Metav IndustryLine Gauge pin, single, 15.31 mm, length 50 mm ideal for end‑measurements, alignment checks and fixture set‑up in workshop metrology Workshop-grade special steel construction Nominal diameter 15.31 mm for end measurements 50 mm length for secure insertion and handling Calibration tolerance ±0.002 mm for fine control Accuracy that supports reliable decisions on the shop floor The compact inspection pin is designed for repeatable end‑measurements, making it suitable for routine quality checks and fixture calibration. With a nominal diameter of 15.31 mm and a stated positional tolerance of ±0.002 mm, the component reduces measurement uncertainty and streamlines pass/fail decisions. The precise diameter specification ensures consistent contact geometry, which simplifies comparison against drawing tolerances and shortens inspection cycles. Robust construction built for regular workshop use Manufactured from special steel, this single gauge pin resists deformation during repeated insertions and withdrawals, maintaining the required dimensional integrity. The 50 mm shank length provides a comfortable engagement depth without excessive overhang, helping to preserve concentricity during use. These mechanical choices reduce the need for frequent replacement and support a steady throughput in production and maintenance environments. Practical handling and protection for transport and storage Supplied as an individual inspection element, the pin arrives ready for integration into gauges, fixtures and test sets. The component’s modest mass and compact geometry ease handling and placement in assemblies, while the protective transport case keeps the surface condition intact during storage and transfer. This reduces preparation time at the workstation and helps maintain the specified ±0.002 mm performance between uses. Integrating the pin into inspection routines and fixtures The product functions well as a reference element in go/no‑go checks, alignment aids and fixture setting, where stable contact surfaces and precise diameters deliver dependable results. Its workshop orientation means the component can be used directly in production inspection loops or as a controlled spare for maintenance benches, supporting a pragmatic quality workflow that prioritises both reliability and uptime. Contact Metav Werkzeuge today for procurement guidance or to discuss suitable inspection fixtures and handling options for this Metav IndustryLine gauge pin Technical Data Article number: M323.F31 GTIN: 4061905068799 Manufacturer: Metav IndustryLine Material: Special steel Facts Diameter: 15.31 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.1 kg Special features Workshop-grade version Delivered in protective case Single-piece gauge pin Intended for end and alignment measurements FAQ What is the intended use of this gauge pin? This gauge pin is intended for end‑measurements, alignment checks and fixture set‑up in workshop metrology; the Metav IndustryLine single gauge pin M323.F31 is optimised for repeatable contact measurements. Is the diameter specification suitable for calibration references? Yes, the nominal 15.31 mm diameter and ±0.002 mm tolerance make the pin suitable as a dimensional reference in routine calibration and go/no‑go checks. Which materials and applications are compatible with the pin? Made from special steel, the pin is suitable for general workshop use and for contact with most common component materials during inspection and alignment tasks. How should the pin be stored to preserve accuracy? Store the pin in its protective case and avoid impact or contamination; the supplied transport case helps keep the measuring surface clean and preserves the specified tolerance. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
15.32mm Gauge Pin, 50mm Length Workshop Version, Special Steel - Metav IndustryLine
Take advantage of a 15.32 mm diameter reference pin with ±0.002 mm tolerance and a 50 mm working length to secure reproducible measurements and efficient quality checks; the special‑steel construction provides long service life under workshop conditions. Order the gauge pin directly via Metav Werkzeuge or ask our consultants if needed. Gauge pin M323.F32 — 15.32 mm diameter, 50 mm length (Metav IndustryLine) The gauge pin M323.F32 is a single, workshop‑grade test pin designed for precise dimensional verification and reference tasks in quality control and fixture set‑ups. High precision ±0.002 mm Diameter 15.32 mm, length 50 mm Special‑grade steel for durability Workshop version for robust use Consistent, measurable accuracy for quality assurance The primary advantage of this gauge pin is its measurable accuracy: a verified tolerance of ±0.002 mm provides a stable reference for pass/fail checks, setup validation and repeat measurements. In practice, this level of precision reduces uncertainty during inspection cycles and shortens decision time when assessing components. The clearly defined 15.32 mm nominal diameter and 50 mm usable length mean the pin integrates easily into existing measurement jigs and inspection routines, enabling faster setup and fewer rechecks. Durable construction for frequent workshop use Manufactured from special steel, the pin is finished for resistance against wear and stand‑alone handling in a busy production environment. The workshop version classification signals robustness: surfaces and tolerances are maintained under repeated seating and removal, which lowers lifecycle costs through extended service intervals. At around 0.1 kg, the pin balances rigidity with manageable handling, making it suitable for bench inspection, fixture alignment and routine verification tasks without the need for elaborate fixturing. Practical versatility across inspection and tooling tasks As a single test pin, the component serves multiple functions in the metrology workflow: reference for gauging operations, datum establishment in fixtures and verification of bores or mating parts when used together with complementary inspection equipment. Its simple geometry and standardised diameter facilitate interchangeability within pin sets or fixture portfolios, helping to harmonise inspection procedures across production stages. The combination of precise tolerance and robust material choice supports reliable outcomes in both shopfloor and toolroom contexts. For workshop‑grade precision and expert guidance, contact Metav Werkzeuge in Emmerich to request the M323.F32 gauge pin and tailored advice from our technical consultants Technical Data SKU: M323.F32 GTIN: 4061905068805 Label: Prüfstift, einzeln, 15,32 mm Länge 50 mm Brand: Metav IndustryLine Material: special steel Accuracy: ±0.002 mm Weight: 0.1 kg Length: 50 mm Diameter: 15.32 mm Facts Diameter: 15.32 mm Length usable: 50 mm Tolerance: ±0.002 mm Weight: 0.1 kg ECLASS: 21170231 Special features Workshop version (robust design) Single test pin for reference and alignment Suitable for fixture and inspection tasks FAQ What applications is this gauge pin suitable for? The gauge pin M323.F32 is intended for dimensional verification, datum setting and alignment in inspection and tooling applications, offering a stable reference in workshop and quality‑control environments. How precise is the M323.F32 in everyday use? The M323.F32 provides a tolerance of ±0.002 mm, which ensures repeatable results for routine pass/fail checks and setup verification under standard workshop conditions. What material is used for the pin and why does it matter? This test pin is made from special steel; the material choice improves wear resistance and maintains dimensional stability during repeated handling and seating. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
15.33mm Gauge Pin Length 50mm Workshop Finish - Metav IndustryLine
Take advantage of the combination of precision tolerance ±0.002 mm, Ø 15.33 mm sizing and a 50 mm working length for reliable end‑measurements and fit checks; order the gauge pin directly via Metav Werkzeuge or consult our specialists for integration advice. Gauge pin M323.F33 — Ø 15.33 mm / 50 mm length, workshop grade (Metav IndustryLine) The Gauge pin M323.F33 is a workshop‑grade test pin designed for accurate end‑measurements and fit verification in metalworking, inspection and assembly tasks. Workshop-grade construction Ø 15.33 mm, 50 mm length Manufactured from special steel Tolerance ±0.002 mm Precision that secures interchangeability With a declared tolerance of ±0.002 mm, this test pin is specified for close‑tolerance checking where dimensional interchangeability is essential. Such a tolerance reduces ambiguity in go/no‑go decisions and is commonly used for final acceptance checks or validation of mating parts. The stated accuracy is achieved through controlled manufacturing processes so that the pin can be used as a reference for plug‑type inspections and end‑dimension verification, helping to cut rework and keep production flow steady. The Ø 15.33 mm nominal size positions the pin for medium‑format bores and fits where small clearance margins must be verified. Built for workshop use and dependable handling Engineered as a workshop‑grade single pin and manufactured from special steel, this component balances hardness and dimensional stability for everyday use. The 50 mm length offers sufficient engagement for most fixture and gauge applications while remaining easy to handle and position by a single operator. Its modest mass and compact shape make mounting in test fixtures uncomplicated, and the material choice supports wear resistance during repeated insertion cycles. Supplied as an individual test pin, the item is suitable for quick replacement in inspection sets and for targeted spot checks on production lines. Practical integration and production benefits Designed for end‑measurement tasks, the pin integrates smoothly into inspection routines and can be combined with existing gauge sets or fixture tooling to enable rapid pass/fail checks. Using a defined reference such as this reduces cycle time at inspection stations and improves traceability of dimensional checks. The workshop specification signals an economical choice for everyday quality control while maintaining measurable precision, which supports stable process control and fewer downstream rejects. Backed by Metav’s distribution and quality assurance, the product is presented as a reliable component for routine metrology tasks. For workshop precision and dependable fit verification, choose the Metav IndustryLine gauge pin M323.F33 — contact Metav Werkzeuge in Emmerich for tailored supply and technical guidance. Technical data Article number: M323.F33 GTIN: 4061905068812 Manufacturer: Metav IndustryLine Facts Diameter: 15.33 mm Length: 50 mm Weight: 0.10 kg Tolerance: ±0.002 mm Special features Material: Special steel Configuration: Single gauge pin Application trigger: end measurements Version: Workshop execution FAQ What accuracy can be expected from this gauge pin? The gauge pin M323.F33 is specified with a tolerance of ±0.002 mm, making it suitable for close‑tolerance inspection and go/no‑go checks. Which materials is the pin intended to check? The M323.F33 from Metav IndustryLine is designed for dimensional fit and end‑measurement tasks; selection of mating part materials should follow standard engineering practice for gauge‑to‑workpiece_CONTACT and wear considerations. Is the pin supplied as a single item or in a set? This article is supplied as a single gauge pin (M323.F33) for flexible use in bespoke inspection setups and replacement in modular gauge assemblies. How long is the usable engagement for measurement? The pin provides a 50 mm usable length suitable for most fixture insertions and engagement depths required in workshop inspection. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
15.34mm Gauge Pin, Single, 50mm Length, Workshop Version - Metav IndustryLine
Take advantage of precise tolerances and a compact form factor to secure reliable end-gauge checks and repeatable inspection routines; the combination of ±0.002 mm accuracy and a hardened special steel construction supports robust workshop workflows. Order the gauge pin directly via Metav Werkzeuge or contact our advisors for application guidance. Test pin M323.F34 — 15.34 mm gauge, 50 mm length (Metav IndustryLine) The M323.F34 test pin is a single gauge pin designed for precise end-measurement tasks and inspection fixtures in workshop environments. High-precision ±0.002 mm tolerance Hardened special steel body Compact 50 mm working length Single-unit delivery for quick replacement Precision where repeatability is essential The M323.F34 provides ±0.002 mm positional accuracy, making it suitable for end-gauge measurements and verification routines where small deviations can affect assembly fits or functional clearances. The nominal diameter of 15.34 mm delivers a defined contact surface for pins, plugs and gauges, reducing uncertainty at the measurement point. Where gauging reliability matters, this level of tolerance minimises rework and supports process control in serial production or quality inspection. Robust construction for daily workshop use Manufactured from special steel, the pin resists wear and preserves dimensional integrity during repeated insertion cycles. The 50 mm overall length balances accessibility with rigidity, so the component can be handled easily while retaining a stable seating in jigs or fixtures. The workshop-grade specification means the component is built for frequent use under typical machine-shop conditions, reducing downtime for replacements and ensuring consistent measurement points over time. Clear identification and integration into quality workflows The single-unit design simplifies stocking and replacement; parts can be identified quickly by the article number and GTIN for traceable inventory management. The compact mass also reduces handling strain in manual processes and supports rapid fixture changes. As a standardised gauge element, the pin integrates straightforwardly into inspection layouts, complementing existing end-gauge sets or bespoke checking fixtures and contributing to reproducible inspection data across shifts. For procurement and precise specification queries about the Metav IndustryLine test pin M323.F34, contact Metav Werkzeuge GmbH in Emmerich by phone or email for tailored supply and technical advice. Technical data Article number: M323.F34 GTIN: 4061905068829 Manufacturer: Metav IndustryLine Numbers / Core technical data Diameter: 15.34 mm Length: 50 mm Tolerance / accuracy: ±0.002 mm Weight: 0.1 kg Special features / Versions Material: special steel Delivery: single test pin Suitable for end-gauge and inspection applications Workshop execution (robust design) FAQ What is the intended application for this test pin? The M323.F34 test pin is intended for end-gauge checks, fixture pins and inspection jigs where a precise cylindrical reference of 15.34 mm is required. How tight is the manufacturing tolerance? Manufactured to an accuracy of ±0.002 mm, the gauge pin meets demanding repeatability requirements for routine inspection tasks. What material is used and how does it affect wear? The pin is produced from special steel, chosen for wear resistance and dimensional stability under frequent use in workshop conditions. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
15.35mm Test Pin Single 50mm Length Workshop Version - Metav IndustryLine
Take advantage of a compact inspection solution that combines 15.35 mm diameter precision, a 50 mm working length and a workshop-grade steel finish for consistent end‑measurement checks. Order the gauge pin directly via Metav Werkzeuge or consult our specialists for application advice. Gauge pin (single) 15.35 mm — 50 mm length, workshop execution (Metav IndustryLine) Gauge pin for fast dimensional verification and end‑measure checks in workshop and inspection environments Workshop execution, robust design Diameter 15.35 mm, high dimensional accuracy Tolerance ±0.002 mm for fine inspection Supplied in protective transport case Precision that supports reliable inspection The compact test pin is manufactured to a diameter of 15.35 mm with a declared tolerance of ±0.002 mm, which positions it for fine inspection work where repeatable fits are required. Such accuracy reduces uncertainty at the go/no‑go stage and makes the component suitable for routine end‑measure checks on turned or machined parts. The pin’s special steel construction provides a stable contact surface that resists wear in normal workshop use, ensuring measurements remain consistent over multiple cycles. Practical handling that keeps production moving With a 50 mm length and a balanced mass, this single gauge pin is easy to handle during manual inspection tasks and bench checks. The workshop execution implies a design optimised for durability under frequent use rather than delicate laboratory handling. For safe transport and on‑site protection the item is supplied in a protective transport case, which helps to prevent nicks and maintains the integrity of the nominal diameter between uses. The compact footprint means the pin can be stored alongside inspection tools without occupying valuable bench space. Seamless integration into inspection routines The pin is intended as a straightforward dimensional reference for end‑measure validation and quick go/no‑go assessments; it can be incorporated into existing manual inspection workflows without special fixtures. Supplied singly as SKU M323.F35, the part is ideal where a precise plug‑type reference or an end‑measure gauge is required for rapid acceptance checks. The robust material choice and workshop finish support repeated contact with metallic components while maintaining the dimensional stability necessary for consistent quality control. Contact Metav Werkzeuge today for delivery options and practical advice on integrating the M323.F35 gauge pin into inspection setups; our Emmerich specialists will help confirm suitability and arrange dispatch. Technical data Article number: M323.F35 GTIN: 4061905068836 Weight: 0.10 kg Material: Special steel Finish: Workshop execution Packaging: Protective transport case Core specifications Diameter: 15.35 mm Length: 50 mm Tolerance: ±0.002 mm Unit: Single item Special features Designed for end‑measurement and go/no‑go checks Robust construction for workshop use Compact, easy to store and transport FAQ What are the exact dimensions of the gauge pin? The gauge pin M323.F35 has a diameter of 15.35 mm and a total length of 50 mm. What tolerance does the test pin meet? The single test pin is manufactured to a tolerance of ±0.002 mm, suitable for fine inspection tasks. How is the item packaged for transport? The product is supplied in a protective transport case to prevent damage and preserve dimensional integrity during handling. Which applications suit this gauge pin best? This gauge pin is intended for end‑measure checks and quick go/no‑go assessments on machined metal components in workshop and inspection settings. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
15.36mm Gauge Pin, Workshop Version, 50mm Length - Metav IndustryLine
The combination of a precision ground 15.36 mm diameter, a compact 50 mm length and a tight tolerance of ±0.002 mm delivers reproducible end‑measure checks and reliable fit control in workshop environments; order the part directly via Metav Werkzeuge or consult our specialists for application advice. Gauge pin, single, 15.36 mm diameter, 50 mm length (Metav IndustryLine) Gauge pin, single, 15.36 mm diameter, 50 mm length for precise end‑measure verification and tooling checks in workshop and inspection tasks. Workshop version, robust design Precision ground 15.36 mm diameter Compact 50 mm length measuring pin Special steel, tolerance ±0.002 mm Consistent, reproducible checks for production control This measuring pin is engineered for high repeatability in routine checks and tooling set‑up. The 15.36 mm diameter, produced to a tolerance of ±0.002 mm, provides a reliable reference for bore verification, end‑measure confirmation and gauge assembly. As a compact, single pin it is particularly suited to tight fixtures and stacked gauge sets where consistent contact geometry is essential. The short, rigid form factor reduces measurement variation caused by bending or misalignment, thereby contributing directly to lower scrap rates and fewer inspection reworks. Durable construction tailored for workshop use Manufactured from special steel, the pin combines dimensional integrity with a workshop‑oriented finish that withstands frequent handling and seating in jigs and gauges. The 50 mm length offers a balance between handling and engagement depth for most common bore checks, while the material selection supports mechanical robustness under repeated insertion and withdrawal cycles. Because the tool is specified as a workshop version, it is optimised for practical daily use rather than fragile laboratory handling, which helps maintain throughput in busy production environments. Practical benefits for calibration, tool setting and assembly As a single, precision pin, this item serves as a simple yet effective datum for end‑measure checks, assembly alignment and the calibration of comparative gauges. Its compact size allows for easy storage in tool drawers or dedicated insert sets while retaining the accuracy required for process control. Integration into existing inspection routines is straightforward: the pin acts as a stable reference point that supports traceable measurements and quick go/no‑go decisions, helping to keep inspection cycles short and predictable. For reliable end‑measure control choose the Metav IndustryLine gauge pin M323.F36 and contact Metav Werkzeuge in Emmerich for tailored advice and supply coordination Technical data Article number: M323.F36 GTIN: 4061905068843 Label: Gauge pin, single, 15.36 mm diameter, 50 mm length Category: Gauge pins Brand: Metav IndustryLine Key dimensions Diameter: 15.36 mm Length: 50 mm Weight: 0.1 kg Tolerance/accuracy: ±0.002 mm Measurement range (min/max): 15.36 mm Features & application Workshop version Material: Special steel Intended use: End‑measure checks, gauge setting, bore verification Suitable for fixture and assembly reference FAQ What is the primary use of this gauge pin? The M323.F36 gauge pin from Metav IndustryLine is intended for end‑measure verification, bore checks and as a reference in gauge setting and fixture alignment. What tolerance and precision can be expected? The pin is manufactured to a tolerance of ±0.002 mm, providing high reproducibility for routine inspection and tool‑setting tasks. Which material is used for the pin? The measuring pin is made from special steel, chosen for its dimensional stability and suitability for workshop use. Can the pin be used in stacked gauge sets or sockets? Yes, the compact 50 mm length and precision diameter make it suitable for stacked gauge assemblies and for acting as a datum in fixtures and sockets. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
15.37mm Gauge Pin 50mm Length Workshop Version - Metav IndustryLine
Combining Ø 15.37 mm diameter, ±0.002 mm tolerance and a 50 mm shaft, this single test pin delivers repeatable end measurements for workshop inspection tasks; order directly via Metav Werkzeuge or contact their advisors for application guidance. Test pin, single, Ø 15.37 mm, 50 mm length (Metav IndustryLine) Test pin, single, Ø 15.37 mm, 50 mm length is a workshop-grade gauge pin for end-measure checks and fixture setting in metalworking environments Workshop-grade construction Diameter Ø 15.37 mm for end gauges High accuracy ±0.002 mm 50 mm hardened special-steel shaft Precise end measurements for consistent production A compact inspection element that supports reproducible end measurement and reference checks, this gauge pin is designed for routine workshop verification. The nominal Ø 15.37 mm and fixed 50 mm shaft length provide a stable datum when establishing reference points in assemblies or gauges. With a declared tolerance of ±0.002 mm, the component reduces measurement scatter and supports consistent pass/fail decisions in repetitive quality-control processes. The small footprint and solid geometry help maintain alignment during insertion and extraction, which is essential for repeatable results. Built for daily workshop use and straightforward handling Engineered as a workshop version, the pin combines robust construction with simple usability for machinists and inspectors. The special steel composition offers enhanced wear resistance compared with softer alternatives, ensuring long service life under frequent contact and slight abrasion. As a fixed-dimension reference pin, it suits end-mass (end gauge) applications, gauge setting and fixture alignment where a reliable, rigid datum is required. The straightforward shape means no special training is necessary to integrate it into existing inspection routines or measuring jigs. Traceable accuracy and compatibility with inspection routines The precision class and measured tolerance make this pin suitable for control tasks where dimensional repeatability matters but ultra‑lab instrumentation is not required. Its accuracy supports conventional workshop QA workflows and can be incorporated into comparator checks, go/no‑go fixtures and assembly verification stations. The compact design aids storage and transport within tool sets and inspection kits. Supplied as a single test element with clear identification (SKU M323.F37 and GTIN 4061905069635), it streamlines inventory management and traceability in the workshop environment. For reliable workshop calibration and rapid supply, request the Metav IndustryLine test pin from Metav Werkzeuge in Emmerich — contact via info@metav-werkzeuge.com or call +49 2822 7131930 for purchase advice and stock information Technical data Article number: M323.F37 GTIN: 4061905069635 Brand: Metav IndustryLine Facts Diameter: 15.37 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.1 kg Special features Material: Special steel Version: Workshop execution Package: single test pin FAQ What is the intended use of this test pin? The test pin is intended as a fixed-dimension reference for end measurements, fixture setting and assembly verification in workshop and production inspection contexts. How accurate is the pin for quality checks? With a specified tolerance of ±0.002 mm, the pin provides tight repeatability suited to precise workshop inspections and comparative measurements. Which materials is the pin compatible with in inspection setups? The hardened special steel shaft is compatible with standard metalworking fixtures and contact points used in machining and assembly verification. Does the product include individual identification for traceability? The single test pin is supplied with the product identification (SKU M323.F37 and GTIN 4061905069635) to support inventory and traceability. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
15.38mm Test Pin, Single, 50mm Length Workshop Version - Metav IndustryLine
Take advantage of the combination of high repeatability, compact dimensions and robust workshop construction for reliable end‑size checks and fixture verification. Order the part directly via Metav Werkzeuge or consult our specialists for matching pins and measurement strategies. Gauge pin M323.F38 — single precision test pin, Ø 15.38 mm, length 50 mm The Gauge pin M323.F38 is a single precision test pin designed for end‑size inspection and fixture alignment in workshop and production environments. Single precision gauge pin Ø 15.38 mm 50 mm length for fixture testing Tolerance ±0.002 mm for tight control Workshop-grade special steel construction High repeatability that reduces inspection uncertainty The compact geometry and tight manufacturing tolerance of this pin deliver consistent results during repetitive checks. With a nominal diameter of Ø 15.38 mm and a runout tolerance of ±0.002 mm, the component is produced to allow repeatable end‑size verification and reliable gauge reference points in assembly jigs. Such dimensional control helps to reduce rework rates and contributes to predictable process capability metrics on the shop floor. Robust construction for everyday workshop use Manufactured from special steel and specified as a workshop version, the pin resists the typical handling and contact loads encountered in industrial measurement tasks. The 50 mm length gives sufficient engagement for many fixture and toolset applications while remaining easy to manoeuvre by hand. The solid construction supports long service life under regular use and helps maintain the geometric integrity that underpins accurate mechanical gauging. Practical integration into inspection routines and tooling As a single test pin, the item is ideally suited for quick pass/fail checks, locating operations and as a reference element in bespoke fixtures. The compact design simplifies storage and insertion into holding devices; when used alongside calibrated master gauges, it becomes part of a reproducible verification loop. If uncertainty remains about selecting the correct diameter or handling requirements, Metav’s product information and specification advice are available to align the component with specific measurement plans. Choose Metav IndustryLine components for dependable workshop measurement: order the M323.F38 precision test pin via Metav Werkzeuge in Emmerich or request application advice from our consultants to ensure the pin matches the inspection task Technical Data SKU: M323.F38 GTIN: 4061905069642 Weight: 0.1 kg Material: Special steel Accuracy: ±0.002 mm Core measurements Diameter: 15.38 mm Length: 50 mm Mass: 0.1 kg Special features Workshop execution Single-piece test pin Intended for end-size inspection and fixture alignment FAQ What tolerance does this gauge pin provide? The Metav IndustryLine gauge pin M323.F38 is manufactured to an accuracy of ±0.002 mm, suitable for tight workshop checks. Can the pin be used for fixture alignment and locating? Yes. The M323.F38 test pin is designed for fixture locating, end‑size checks and as a reference element in jigs and assemblies. What material is the pin made from? The pin is made from special steel and specified in a workshop-grade execution for robust everyday use. What are the exact dimensions of the pin? Nominal diameter is 15.38 mm with a length of 50 mm; the SKU is M323.F38 for ordering and traceability. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
15.39mm Test Pin, 50mm Length Workshop Version, Special Steel, Packed in Case - Metav IndustryLine
Take advantage of the combination of high repeatability, compact micro‑range dimensions and robust workshop design for reliable end‑measurement in tight production processes; order the gauge pin directly via Metav Werkzeuge or ask our consultants if needed. Gauge pin, single — 15.39 mm Ø, 50 mm length (Metav IndustryLine) The Gauge pin, single — 15.39 mm Ø, 50 mm length is a compact workshop pin for precise end measurements and fit checks in micro‑range inspection tasks. High precision ±0.002 mm Micro‑range: 15.39 mm diameter Workshop design for robust handling Supplied in transport box Precision that reduces rework and inspection time The compact checking pin is manufactured for repeatable results where small tolerances matter. With a declared variation of ±0.002 mm, the pin delivers the sort of precision required for dimensional controls and go/no‑go verifications in serial inspection. This accuracy reduces the need for repeated setups and minimises rework, improving throughput in quality control stations. The combination of a true 15.39 mm working diameter and a 50 mm usable length helps to stabilise contact during measurement and to provide consistent datum references. Compact format with a workshop‑ready build Engineered as a workshop design, this inspection pin balances stiffness and handling for everyday use at the bench or in production lines. The short, stiff profile suits micro‑range tasks where large callipers are impractical; classification within the micro‑range ensures the tool remains rigid and simple to position even on small parts. Construction from special steel gives mechanical resilience and wear resistance in regular use, so the component retains form across many measurement cycles. Practical handling, storage and transport The pin’s geometry and modest mass make single‑handed placement straightforward during rapid checks. Supplied in a transport box, the item is protected during storage and transit, supporting safe handling between job sites or inspection benches. The compact footprint simplifies tool organisation in a busy workshop and lowers the risk of damage that can affect measurement integrity, helping to preserve the declared tolerance over time. Where this pin delivers measurable benefit Ideal for end‑dimension verification, plug‑fit testing and assembly checks, the product serves toolmakers, precision workshops and quality departments that require a small, reliable master gauge. The robust material and controlled dimensions suit repeated probing of bores, recesses and fitted components, where a stable reference reduces cumulative measurement uncertainty and supports faster decision‑making on the production floor. Contact Metav Werkzeuge in Emmerich for procurement advice and technical clarification on the Metav IndustryLine gauge pin — phone +49 2822 7131930 or email info@metav-werkzeuge.com Technical data SKU: M323.F39 GTIN: 4061905069659 Brand: Metav IndustryLine Category: Gauge pins Weight: 0.1 kg Facts Diameter: 15.39 mm Length: 50 mm Variation/tolerance: ±0.002 mm Mass: 0.1 kg Special features Material: special steel Workshop design Supplied in transport box Micro‑range classification for fine parts FAQ What accuracy can be expected from this gauge pin? The gauge pin offers a declared variation of ±0.002 mm; this level of repeatability makes the pin suitable for tight tolerance checks and reliable go/no‑go assessments. Is the pin suitable for everyday workshop use? Yes, the Metav IndustryLine gauge pin is built in a workshop design from special steel, combining wear resistance with handling robustness for daily inspection tasks. Which measurement tasks does this pin cover best? The pin is optimised for end‑dimension verification, plug‑fit testing and checking small bores or recesses where a compact, precise reference is required. Does the product include protective packaging? The component is supplied in a transport box to protect the pin during storage and transfer, preserving dimensional integrity between uses. Can this item be used as a master for go/no‑go checks? With its controlled diameter of 15.39 mm and ±0.002 mm variation, the pin is appropriate as a master check for fit and clearance verifications in production environments. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
15.3mm Gauge Pin Single 50mm Length Workshop Version - Metav IndustryLine
Compact reliability for precision end measurement: combine the 15.3 mm diameter, ±0.002 mm tolerance and robust special steel construction for repeatable reference measurements in workshop environments. Order the part directly via Metav Werkzeuge or consult the specialists for supply and fitment advice. Gauge pin, single, 15.3 mm diameter, 50 mm length (Metav IndustryLine) Gauge pin, single, 15.3 mm diameter, 50 mm length is a workshop-grade reference pin for precise end‑measurement and fit checks in production and inspection processes. Workshop design for robust daily use Diameter 15.3 mm, length 50 mm Tolerance ±0.002 mm for tight fits Made from special steel for wear resistance Ensure repeatable fits with micrometric tolerance The test pin provides a tolerance of ±0.002 mm, making it suitable where consistent clearances and tight fits determine quality. As a compact reference element, the pin supports end measurement and functional control tasks, reducing rework and assembly trial‑and‑error. The guaranteed dimensional stability of the hardened special steel core preserves datum accuracy over repeated use, so measurement data remain comparable across shifts and batches. This rational advantage translates directly into fewer rejects and more predictable production outcomes. Built for workshop environments and frequent handling Designed as a workshop execution tool, the pin balances surface hardness and toughness to resist chipping during routine handling. At 50 mm length and a diameter of 15.3 mm, the geometry provides comfortable gripping and stable seating in fixtures or test jigs. The compact format is ideal for bench inspection or insertion checks, while the low mass (0.1 kg) keeps handling simple during high‑volume sampling. Durability reduces replacement cycles and maintenance, contributing to lower life‑cycle costs and smoother operations. Clear specification makes integration straightforward Traceable identification and compact dimensions simplify inventory and process documentation. The product functions as a standardised reference for go/no‑go assessments and dimensional verification in workshops and small series production. With straightforward geometry and clearly stated characteristics, the pin is uncomplicated to implement in incoming inspection, assembly controls or toolroom checks. The combination of defined diameter, length and tolerance supports objective decision thresholds and reliable pass/fail criteria. For workshop-ready precision from the Metav IndustryLine, request the M323.F30 gauge pin via Metav Werkzeuge and speak with our consultants about availability and delivery options Technical data Article number: M323.F30 GTIN: 4061905068782 Brand: Metav IndustryLine Material: Special steel Facts Diameter: 15.3 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.1 kg Special features Workshop-grade execution Single gauge pin for end measurement Category: Gauge pins / Messstifte Story trigger: end measurement FAQ What nominal size does the gauge pin have? The gauge pin has a nominal diameter of 15.3 mm and a length of 50 mm; the M323.F30 is intended for precise end‑measurement tasks. How tight is the dimensional tolerance? The pin is manufactured to a tolerance of ±0.002 mm, giving the M323.F30 suitability for applications that require very small clearance margins. What material is used for the pin? The test pin is made from a special steel chosen for wear resistance and dimensional stability during repeated use. Is the pin suited for everyday workshop use? Yes; the workshop execution and compact geometry make the pin appropriate for routine inspection, fixture checks and assembly verification. Can the pin be used as a reference in production control? The M323.F30 serves as a repeatable reference pin for end‑measurement and quick go/no‑go checks, supporting consistent production control. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
15.41mm Gauge Pin 50mm Length, Workshop Version, Special Steel ±0.002mm - Metav IndustryLine
Combine high repeatability (±0.002 mm) with a 15.41 mm diameter and 50 mm length for dependable end‑measure checks; order the gauge directly via Metav Werkzeuge or consult our specialists for application advice. Test pin M323.F41 — gauge pin, 15.41 mm diameter, 50 mm length (Metav IndustryLine) A Test pin M323.F41 for precise end‑measure and bore verification in workshop and inspection environments. Workshop version for robust use Diameter 15.41 mm for end‑measure checks Length 50 mm for recessed measurements Tolerance ±0.002 mm for consistent repeatability Reliable end‑measure control for production and quality inspection The M323.F41 functions as a compact, purpose‑built gauge pin for repeatable end‑measure and bore checks in workshop settings. Its nominal 15.41 mm diameter combined with a 50 mm overall length provides sufficient reach for many recessed or deep features while remaining easy to handle. The close tolerance of ±0.002 mm reduces the need for repeat measurements and helps maintain throughput by cutting rework cycles. Presented as a workshop version, the component withstands everyday handling and supports routine inspection tasks without specialised fixtures. Material choices and what they mean for wear and measurement stability Manufactured from special steel, the pin balances hardness and surface finish to preserve dimensional stability over repeated use. The chosen material supports stable contact conditions that are essential for reproducing readings between operators and across shifts. Where contact metallurgy and surface condition influence results, the pin’s finish minimises friction and scoring. This combination of material and geometry means the instrument remains reliable for serial quality checks and gives engineers confidence that readings reflect the part, not tool wear. Practical integration into inspection procedures As a single gauge element, the pin is quick to fit into standard inspection jigs, plug gauges or manual probe set‑ups used in workshop metrology. The compact format simplifies storage and handling while the defined length helps when verifying stepped bores or locating shoulders. By delivering consistent contact geometry and reducing operator‑dependent variability, the pin contributes to measurable improvements in inspection repeatability and process control. Where traceable documentation is required, the product identity and specifications support clear recording in inspection reports. Robust handling and delivery considerations for the workshop Designed for everyday industrial use, the pin is supplied ready for storage and transport in a protective case to avoid transit damage and preserve the working surface. The workshop version approach prioritises resilience and easy deployment on the shop floor. Combining solid construction with straightforward handling reduces downtime spent searching for matched pins and supports a more efficient inspection routine, which is especially valuable in busy production environments. Specify the M323.F41 from Metav IndustryLine for dependable end‑measure inspection — contact Metav Werkzeuge in Emmerich for availability and technical advice at info@metav-werkzeuge.com or on +49 2822 7131930 Technical Data Article number: M323.F41 GTIN: 4061905069673 Manufacturer: Metav IndustryLine Weight: 0.1 kg Facts Diameter: 15.41 mm Length: 50 mm Tolerance / accuracy: ±0.002 mm Net measurement range min/max: 15.41 mm Special features Material: special steel Workshop version for robust handling Delivered in a protective transport case Intended use: end‑measure and bore verification FAQ What applications is this test pin suited for? The M323.F41 test pin is intended for end‑measure checks and bore verification in workshop and inspection environments, offering a compact solution for recessed or stepped features. What level of accuracy can be expected? The pin is specified with a tolerance of ±0.002 mm, delivering high repeatability for routine quality control tasks. What material is the pin made from and why does that matter? Made from special steel, the pin offers a balance of surface stability and wear resistance that helps maintain consistent measurement results over repeated use. Is the pin supplied ready for storage and transport? Yes, the M323.F41 is supplied in a protective transport case to preserve the measuring surface and avoid damage during handling. How does the length influence measurement tasks? At 50 mm overall length, the pin reaches recessed areas and shoulders more easily than shorter gauges while remaining simple to handle for fast, repeatable checks. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
15.42mm Gauge Pin Length 50mm Workshop Finish - Metav IndustryLine
Take advantage of high repeatability and a tight ±0.002 mm tolerance together with the compact 15.42 mm diameter / 50 mm length for reliable go/no-go and reference checks in production or inspection. Order this precision gauge pin directly via Metav Werkzeuge or request specialist advice from their consultants. Gauge pin, single — 15.42 mm diameter, 50 mm length (Metav IndustryLine) A gauge pin, single (15.42 mm) intended for precise bore and ring gauging in workshop and inspection environments. High precision ±0.002 mm tolerance Hard-wearing special steel for longevity Diameter 15.42 mm for snug fits Compact 50 mm working length Precision where it counts for routine inspection This inspection pin is manufactured to a tolerance of ±0.002 mm, ensuring high-precision decisions when checking bores, dowel holes and mating parts. The tight tolerance reduces ambiguity in pass/fail decisions and supports process control documentation. In practice, such an accuracy level enables repeatable checks at production lines and inspection benches, where consistent measurement outcomes are required for quality assurance. The compact design also minimises thermal and handling influence during short measurement cycles. Durable material and workshop-ready design Made from special steel, the pin is intended for repeated use under workshop conditions; the material selection balances wear resistance with stable dimensional behaviour. A hard-wearing surface decreases the rate of wear at contact points, which prolongs the service life and maintains fit reliability over many cycles. For applications where surface finish and contact geometry matter, the material and machining quality contribute to consistent engagement and low-profile marking on mating parts. Compact dimensions for tight spaces and fast handling With a diameter of 15.42 mm and a working length of 50 mm, the pin is sized for confined bores and assemblies where access is limited. The short length reduces bending and handling variability, which is especially useful for routine end‑of‑line checks or batch sampling. The modest mass facilitates quick manual handling and rapid inspection sequences without sacrificing the rigidity needed for meaningful go/no-go assessments. Traceable identification and workshop applicability The component is supplied as a single gauge pin with clear identification for inventory and quality records: SKU M323.F42 and GTIN 4061905070037. This labelling supports traceability in inspection logs and simplifies replacement ordering. The product’s workshop version specification makes it suitable for everyday industrial use, serving as a simple reference gauge or end mass for go/no-go evaluation in machining and assembly operations. For dependable bore and ring checks choose the Metav IndustryLine gauge pin — contact Metav Werkzeuge in Emmerich for tailored technical guidance and reliable supply. Technical data SKU: M323.F42 GTIN: 4061905070037 ECLASS: 21170231 Numerical data Diameter: 15.42 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.1 kg Design & special features Material: Special steel Workshop version Label: Gauge pin, single, 15.42 mm length 50 mm Story trigger / application: end measurement FAQ What inspection tasks is this pin suited for? The single gauge pin is designed for bore and ring gauging, serving as a reference for go/no-go checks and quick dimensional verification in production and inspection. Is the pin suitable for frequent use in a production environment? Yes, the Metav IndustryLine pin is specified as a workshop version with a hard-wearing special steel construction intended for regular inspection cycles. How is the product identified for inventory and traceability? Identification is provided via SKU M323.F42 and GTIN 4061905070037, which simplifies logging and reordering. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
15.43mm Gauge Pin, Single, 50mm Length Workshop Version - Metav IndustryLine
Benefit from workshop‑grade robustness, an exact ±0.002 mm tolerance and a compact 50 mm length that together ensure reliable end‑measurement verification in small bores; order the inspection pin directly via Metav Werkzeuge or contact our consultants for application advice. Inspection pin, single, 15.43 mm, length 50 mm — Metav IndustryLine workshop pin with ±0.002 mm accuracy the Inspection pin, single, 15.43 mm, length 50 mm is a workshop‑grade gauge pin designed for precise end‑dimension checks and test‑fit verification in small components Workshop‑grade construction Diameter 15.43 mm for end‑measure checks Length 50 mm for robust handling Tolerance ±0.002 mm precision Precision where small tolerances matter This workshop‑grade gauge pin delivers repeatable measurement performance with a specified tolerance of ±0.002 mm, making it suitable for verification tasks where tight limits are critical. The stated accuracy supports confident acceptance or rejection decisions in quality checks and reduces rework by clarifying whether a bore or fit meets specification. Measured values are directly comparable thanks to the compact geometry and the clearly defined nominal diameter of 15.43 mm. Durable design for shopfloor handling Manufactured from special steel, the pin is engineered to withstand regular use in an industrial environment while maintaining form stability. The compact 50 mm length offers a balance between accessibility in confined bores and mechanical stiffness during insertion and withdrawal. Delivered in a protective case suitable for transport, the component is protected from handling damage and contamination, keeping workshop processes efficient and tools ready for immediate use. Practical fit‑check applications and workflow benefits As a single inspection pin, the item is ideal for end‑measure and test‑fit tasks in assembly, jig setting and incoming inspection of small components. The robust construction minimises deformation risk during repeated checks and simplifies handling in production routines. Using a clearly specified gauge pin reduces uncertainty in measurement chains, shortens inspection times and supports consistent production throughput in small‑part manufacturing. For consistent small‑bore verification choose the Metav IndustryLine inspection pin M323.F43 and contact Metav Werkzeuge for tailored advice or application recommendations — Metav Werkzeuge can assist with technical details and supply options. Technical Data Article number: M323.F43 GTIN: 4061905070044 Manufacturer: Metav IndustryLine Facts Diameter: 15.43 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.1 kg EClass: 21170231 Special features Workshop execution Material: special steel Delivered in a protective case for transport Category: Gauge pin / inspection pin Intended use: end‑dimension and test‑fit checks FAQ What measurement accuracy can be expected from this gauge pin? The inspection pin specifies a tolerance of ±0.002 mm, giving high repeatability for end‑dimension verification when used as a reference in workshop checks. Is the pin suitable for small‑bore acceptance testing? Yes; the 15.43 mm diameter and compact 50 mm length make the pin well suited to test‑fit and end‑measure checks in small bores and precision components. Which material is used and how does it affect durability? The pin is made of special steel, selected for wear resistance and mechanical stability to withstand regular shopfloor handling without rapid degradation. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
15.44mm Test Pin, Workshop Version, 50mm Length - Metav IndustryLine
Take advantage of workshop-grade robustness combined with high measurement accuracy — the 15.44 mm diameter, 50 mm length and a tight ±0.002 mm tolerance deliver repeatable end‑measure checks. Order the component directly via Metav Werkzeuge or request technical clarification from our consultants. Gauge pin, single, 15.44 mm (50 mm length) — Metav IndustryLine The gauge pin, single, 15.44 mm is a workshop‑grade end‑measurement pin engineered for dependable reference positioning and repeatable dimensional checks in inspection and set‑up tasks. Workshop version for robust use Diameter 15.44 mm, length 50 mm Precision ground, special steel construction Accurate reference with micrometre‑level repeatability The Metav IndustryLine gauge pin (M323.F44) is manufactured to a measured variation of ±0.002 mm, which corresponds to a reproducible dimensional window in the low micrometre range. As a precision‑ground cylindrical reference, it reduces run‑out and contact variability during end‑measure checks and alignment tasks. This level of dimensional control supports reliable go/no‑go decisions and consistent fixture set‑ups, simplifying quality control loops while reducing rework. Built for daily workshop use and long service life Produced in special steel and delivered in a workshop specification, this pin balances wear resistance with manageable handling. The compact 50 mm length and modest 0.1 kg mass make it easy to position in jigs and gauges without introducing handling fatigue, while the machined surface preserves repeatable contact points. The robust finish and straightforward geometry mean fewer surface defects during routine use, which translates into fewer measurement interruptions and a lower maintenance burden. Practical applications and integration into inspection routines The pin is intended primarily for end‑measurement, positioning and reference duties in toolrooms, assembly fixturing and quality control benches. Its single‑piece delivery and standard dimensions permit seamless incorporation into inspection jigs and manual comparators. When added to inspection workflows, the component provides a consistent datum for comparative checks and dimensional verification, making it a useful tool for production sampling and set‑up validation. Contact Metav Werkzeuge today to specify delivery quantities or to discuss how the Metav IndustryLine gauge pin M323.F44 fits into existing inspection equipment Technical data Article number: M323.F44 GTIN: 4061905070785 Brand: Metav IndustryLine Material: Special steel Version: Workshop version Label: Gauge pin, single, 15.44 mm length 50 mm Facts Diameter: 15.44 mm Length: 50 mm Dimensional variation: ±0.002 mm Weight: 0.1 kg eClass: 21170231 Special features Precision ground cylindrical reference Designed for end‑measure checks and positioning Single‑piece delivery Workshop‑specification finish FAQ What material is the gauge pin made from? The Metav IndustryLine gauge pin (M323.F44) is manufactured from special steel to provide a balance of surface hardness and wear resistance suitable for repeated reference use. What is the dimensional tolerance of this gauge pin? The Metav IndustryLine gauge pin (M323.F44) is specified with a dimensional variation of ±0.002 mm, offering micrometre‑level repeatability for precise end‑measure tasks. Which inspection tasks is this pin intended for? The Metav IndustryLine gauge pin (M323.F44) is intended for end‑measurement, positioning, fixture set‑up and comparative checks in toolroom and production inspection routines. Can this pin be used for fixture and gauge set‑ups? Yes — the Metav IndustryLine gauge pin (M323.F44) is suitable as a reference element in fixtures and gauges where a stable, precision cylindrical datum is required. How should the gauge pin be maintained to ensure longevity? Routine care for the Metav IndustryLine gauge pin (M323.F44) includes keeping contact faces clean, protecting the surface from corrosion and handling with soft‑jawed clamps to avoid nicks that would affect repeatability. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
15.45 mm Gauge Pin, Single, 50 mm Length, Workshop Finish - Metav IndustryLine
Take advantage of a workshop‑grade gauge pin that combines special steel construction with a tight tolerance of ±0.002 mm for consistent end‑measurement and fit verification; order directly via Metav Werkzeuge or consult our technical team for application advice. Gauge pin M323.F45 — single test pin, Ø 15.45 mm, 50 mm length (Metav IndustryLine) Gauge pin M323.F45 is a single precision test pin designed for measuring and checking bore fits, end faces and fixture locations in workshop environments Workshop version, robust design Diameter 15.45 mm for precise fits Length 50 mm for end‑measurement tasks Tolerance ±0.002 mm for high accuracy Precision for repeatable fit checks The M323.F45 is manufactured from special steel, heat‑treated and finished to deliver a highly repeatable datum for go/no‑go and reference checks. Its Ø 15.45 mm diameter and 50 mm effective length make it suitable for verifying bore sizes, locating dowel positions and confirming seating surfaces where a compact, rigid pin is required. The combination of small form factor and workshop grading reduces handling time during batch checks while maintaining tactile robustness on the shop floor. Measurable accuracy that supports quality control With a stated tolerance of ±0.002 mm, the pin supports tight inspection routines and statistical process control at component level. This tolerance level allows the pin to function as a reliable reference in assembly verification and first‑article inspection, reducing downstream rework. The precise finish also helps to minimise measurement uncertainty when used with micrometres or comparators, making the part a practical tool for both manual inspection and integration into fixture setups. Practical handling and protected shipment Delivered as a single item in a transport case, the pin is protected from handling damage during storage and transit; the case is suitable for workshop logistics. The compact 0.1 kg mass ensures easy handling and quick placement in fixtures or test jigs. A clear SKU and GTIN facilitate inventory management and traceability for procurement and quality records, while the workshop design prioritises durability where repeated contact and insertion are typical. For workshop‑grade inspection tools from Metav IndustryLine, order the M323.F45 gauge pin through Metav Werkzeuge in Emmerich or contact our specialists at info@metav-werkzeuge.com for tailored advice Technical Data Article number: M323.F45 GTIN: 4061905070792 Manufacturer: Metav IndustryLine Facts Diameter: 15.45 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.1 kg Special features Material: Special steel Workshop version (robust design) Supplied in transport case (plastic or wooden) FAQ What is the declared tolerance of the pin? The declared tolerance of the M323.F45 gauge pin is ±0.002 mm, making it suitable for high‑precision fit verification and inspection tasks. Can the pin be used for bore checking and fixture alignment? Yes, the M323.F45 is intended for bore checking, dowel and fixture location verification and end‑face measurements in workshop environments. How is the pin supplied to protect it in transit? The gauge pin is supplied as a single item in a transport case (plastic or wooden), preventing damage during storage and shipping. Which material is used for the pin and what does that mean for durability? The pin is made from special steel, providing mechanical strength and surface finish stability required for repeated insertion and positional checks. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
15.46mm Gauge Pin Length 50mm Workshop Finish - Metav IndustryLine
Take advantage of the combination of ±0.002 mm manufacturing tolerance, special steel construction and compact 50 mm length for reliable end‑measure checks and jig validation; order the gauge pin directly via Metav Werkzeuge or ask our consultants for application advice. Gauge pin M323.F46 — Single test pin, Ø 15.46 mm, length 50 mm (Metav IndustryLine) The Gauge pin M323.F46 is a workshop‑grade single test pin designed for precise end‑measure checks, bore verification and assembly fitting in inspection and production environments Workshop-grade construction Diameter precisely 15.46 mm High accuracy ±0.002 mm Delivered in protective plastic case Precision that keeps production within tolerance This gauge pin is manufactured to a tight ±0.002 mm tolerance, delivering consistent repeatability for critical checks on mating parts and jigs. The small diameter and short length make it particularly suited to fine alignment tasks and end‑measure verification where dimensional certainty prevents assembly rejects. By using a hardened special steel alloy, the pin maintains form stability under repeated use; this minimises wear and keeps inspection data reliable over many cycles. The technical specification therefore supports fast, evidence‑based decisions on part conformity and reduces rework time in high‑mix workshops. Compact format for bench and gauge applications With a 50 mm usable length and a nominal Ø 15.46 mm, this single test pin fits inspection fixtures, plug gauges and measuring jigs without adding unnecessary overhang. The compact design reduces the risk of bending during manual handling and simplifies one‑hand placement in repetitive test routines. Lightweight construction (approx. 0.1 kg) and the included protective case facilitate tidy storage and safe transport between workstations. This combination of compactness and robustness makes the pin a practical choice for maintenance, small‑batch production runs and quality control benches. Built for workshop realities and supply reliability The workshop execution underlines practical durability: surfaces are prepared for smooth seating in bores and to limit scoring of mating components. The product is supplied as a single item with traceable identity (SKU M323.F46), enabling straightforward inventory handling and batch tracking. Sourcing through Metav delivers the advantage of centralised European logistics and a quality‑filter process based in Emmerich, which helps ensure consistent delivery performance for production procurement. For engineers seeking a reliable reference pin that integrates easily into inspection procedures, this test pin offers a balance of precision, handling ease and availability. Contact Metav Werkzeuge today to discuss suitability for specific gauges or to request delivery of the M323.F46 single gauge pin from Metav IndustryLine Technical data SKU: M323.F46 GTIN: 4061905070808 Article: Gauge pin, single, Ø 15.46 mm, length 50 mm Brand: Metav IndustryLine Facts Diameter: 15.46 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.1 kg Special features Material: special steel Workshop execution Delivery: protective plastic case for transport FAQ How precise is the gauge pin for dimensional checks? The gauge pin M323.F46 is manufactured to a tolerance of ±0.002 mm, making it suitable for accurate end‑measure and fit checks in workshop and inspection settings. What material is the pin made from and why does it matter? The pin is made from special steel, which provides a durable contact surface and good wear resistance for repeated insertion and removal in bores and fixtures. Is the product supplied ready for storage and transport? Yes, the test pin is delivered in a protective plastic case to prevent damage during transport and to simplify safe storage between uses. Can the pin be used in assembly jigs and plug gauges? The compact 50 mm length and precise Ø 15.46 mm diameter make the pin suitable for many plug gauge and jig applications where a single reference diameter is required. How is the item identified for inventory and ordering? The product is listed under SKU M323.F46 and GTIN 4061905070808 for straightforward ordering and stock management. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
15.47mm Gauge Pin, Workshop Version, 50mm Length - Metav IndustryLine
A compact workshop gauge pin with Ø 15.47 mm and length 50 mm delivers repeatable fit checks thanks to its ±0.002 mm tolerance and robust special-steel construction; supplied in a protective case for safe handling. Order the item directly via Metav Werkzeuge or consult our advisors for application-specific guidance. Gauge pin, single, Ø 15.47 mm, length 50 mm (Metav IndustryLine) The gauge pin, single, Ø 15.47 mm, length 50 mm is a workshop-grade test pin designed for precise go/no-go fit verification and small-part dimensional checks in production and inspection environments. Workshop-grade construction Precise tolerance ±0.002 mm Diameter Ø 15.47 mm, length 50 mm Delivered in protective case Consistent inspection results through tight tolerance The tight ±0.002 mm tolerance ensures that each pin provides a reliable reference for go/no-go checks and assembly clearance verification. Where repeatability matters, the controlled diameter holds manufacturing variances to a minimum and reduces ambiguity during pass/fail decisions. The small form factor and defined geometry support fast, repeatable gauging routines that lower cycle time and minimise subjective judgement in visual or tactile checks. Durable design for daily workshop use Constructed from special steel, the test pin resists wear and maintains geometry under regular handling, which prolongs useful life and reduces replacement frequency. The workshop version finish offers a balance between corrosion resistance and the friction characteristics needed for insertion and withdrawal in common jigs and bushings. Supplied in a protective case, the pin is protected during transport and storage, helping to preserve its dimensional integrity until it reaches the inspection bench. Easy integration into measurement workflows The compact geometry—Ø 15.47 mm and length 50 mm—fits standard inspection setups and indexing fixtures, enabling quick insertion into existing test benches or fixture stacks. Traceable identification via SKU and GTIN supports inventory control and part traceability in quality documentation. The lightweight construction facilitates handling during high-volume checks while the clearly defined dimensions simplify documentation in inspection records and work instructions. For reliable small-diameter verification choose the Metav IndustryLine gauge pin and contact Metav Werkzeuge for tailored advice or to request the item under SKU M323.F47 via info@metav-werkzeuge.com or by phone on +49 2822 7131930 Technical data Article number: M323.F47 GTIN: 4061905070815 Label: Gauge pin, single, Ø 15.47 mm, length 50 mm Facts Diameter: 15.47 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.1 kg Special features Material: Special steel Workshop version Supplied in protective case Category: Gauge pins eClass: 21170231 FAQ What is the nominal diameter and length of this gauge pin? The gauge pin has a nominal diameter of 15.47 mm and a length of 50 mm, as specified for the Metav IndustryLine single gauge pin M323.F47. How accurate is the diameter of the pin? The diameter is manufactured to a tolerance of ±0.002 mm, which supports precise go/no-go and fit-control checks in production environments. Is the pin suitable for routine workshop inspection? Yes, the workshop version construction and the robust special-steel material make this test pin suitable for regular inspection tasks and repeated handling. How is the product delivered and protected in transit? The pin is supplied in a protective case to safeguard the measuring surface during transport and storage, preserving its dimensional integrity. Can this item be used for traceable inventory and documentation? Yes, the product is identifiable by SKU M323.F47 and GTIN 4061905070815, which supports traceability and documentation within quality-management systems. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
15.48mm Gauge Pin 50mm Length Workshop Version, Special Steel - Metav IndustryLine
Take advantage of the combination of high repeatability, compact workshop dimensions and robust material for reliable end‑size inspection. The precise 15.48 mm diameter and ±0.002 mm tolerance ensure consistent process control; order directly via Metav Werkzeuge or consult the technical team for application advice. Test pin M323.F48 — Gauge pin, 15.48 mm diameter, 50 mm length (Metav IndustryLine) The Test pin M323.F48 is a compact inspection pin designed for end‑size verification and workshop metrology tasks, offering high repeatability in a small footprint. Metav IndustryLine precision gauge pin Diameter 15.48 mm for end‑size verification Length 50 mm, compact workshop format Tolerance ±0.002 mm for repeatable inspection Precision that keeps production running The inspection pin is engineered for process control where accuracy matters. With a nominal diameter of 15.48 mm and a stated repeatability of ±0.002 mm, this gauge pin supports tight end‑size checks and reduces downstream rework. The presented tolerance corresponds to industry needs for fine inspection tasks and provides a reliable reference for go/no‑go testing and gauge setup. Because the component is made from special steel, dimensional stability under normal workshop conditions is improved, which helps maintain consistent measurement results over repeated cycles. Designed for practical workshop use and simple handling Compact dimensions and a 50 mm length give this inspection pin a favourable balance of reach and rigidity that is ideal for bench inspection and fixture verification. The workshop variant construction reduces the risk of deformation during handling while remaining easy to integrate into jigs and test rigs. The form factor aids quick positioning and repeatable seating in gauges, making routine checks efficient and lowering per‑check time. The robust finish simplifies cleaning and extends service intervals, supporting uninterrupted quality control in small to mid‑sized production environments. Materials, delivery and traceable identification Constructed from special steel, the pin offers wear resistance suitable for regular use in inspection workflows. The item is supplied as a single unit with clear identification (SKU M323.F48) and a traceable global trade item number, enabling straightforward inventory and traceability management. For transport and protection the test pin is delivered in a dedicated transport case, which reduces the risk of damage in transit and during storage. This practical packaging supports safe handling in both workshops and inspection labs without the need for additional protective measures. Choose Metav IndustryLine test pins for dependable end‑size control and request a tailored supply from Metav Werkzeuge in Emmerich — info@metav-werkzeuge.com / +49 2822 7131930 Technical data SKU: M323.F48 GTIN: 4061905070822 Article: Test pin, single, 15.48 mm, length 50 mm Brand: Metav IndustryLine Core specifications Diameter: 15.48 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.1 kg Materials and features Material: special steel Workshop variant Delivered in transport case Eclass: 21170231 FAQ What level of dimensional accuracy does this inspection pin provide? The Test pin M323.F48 is specified with a tolerance of ±0.002 mm, making the gauge pin suitable for fine end‑size verification and repeatable workshop inspection tasks. Is the pin suitable for fixture and gauge setting in small‑batch production? Yes, the compact 50 mm length and the stable diameter make this inspection pin appropriate for fixture alignment, gauge setting and quick go/no‑go checks in small to mid‑sized production runs. What is the material and how does it affect durability? Manufactured from special steel, the inspection pin resists wear under normal inspection conditions and retains dimensional stability for repeated use. How is the item delivered and protected? The product is supplied as a single unit (SKU M323.F48) and is delivered in a transport case to protect the pin during shipment and storage. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
15.49mm Gauge Pin 50mm Length Workshop Finish - Metav IndustryLine
Take advantage of a compact, workshop-grade inspection solution that combines precise dimensional control, robust special-steel construction and short handling lengths for reliable end‑dimension checks; order the gauge pin directly via Metav Werkzeuge or consult our technical team for specification matching. M323.F49 gauge pin, single — Ø 15.49 mm, length 50 mm (Metav IndustryLine) The M323.F49 gauge pin is a workshop‑grade precision inspection pin designed for fast end‑dimension checks and fixture alignment in toolrooms and small-scale production environments. Workshop‑grade construction Diameter 15.49 mm, length 50 mm Special steel for robust handling Consistent dimensional control for fast inspection The short, rigid design of this precision gauge pin delivers repeatable results where tight tolerances matter. With a specified dimensional deviation of ±0.002 mm, the pin provides an objective, measurable basis for go/no‑go checks and reference fits. The compact format reduces bending and handling error compared with longer probes, enabling quicker cycle times during batch checks. This practical accuracy supports efficient quality control workflows and reduces the likelihood of rework in downstream processes. Built for workshop use and everyday robustness Constructed from special steel and supplied in a workshop execution, the pin withstands routine handling and the knocks of shop environments without sacrificing measurement reliability. The solid material choice ensures surface integrity at the contact points and reliable seating in gauges and fixtures. For operations that require a balance between durability and precision, this format offers a pragmatic compromise: robust enough for daily use, yet precise enough for critical end‑dimension verification. Application focus: end‑dimension checks and fixture set‑up Ideal where compact size and exact diameter are required, this gauge pin suits tasks such as end‑dimension verification, alignment of fixtures and verification of mating parts. The nominal diameter of 15.49 mm and 50 mm overall length make it particularly useful in tooling, jig set‑up and small‑batch inspection scenarios where access is limited and exact fit assessment is essential. The clear, numerical specification allows straightforward integration into existing inspection routines and documentation. For procurement or technical advice on this workshop‑grade gauge pin from Metav IndustryLine, contact Metav Werkzeuge in Emmerich by phone +49 2822 7131930 or e‑mail info@metav-werkzeuge.com Technical data SKU: M323.F49 GTIN: 4061905070839 Category: Gauge pins Facts Diameter: 15.49 mm Length: 50 mm Dimensional deviation: ±0.002 mm Weight: 0.1 kg Special features Material: Special steel Workshop execution Application: End‑dimension checks, fixture alignment FAQ What is the nominal diameter of the gauge pin? The nominal diameter is 15.49 mm for the M323.F49 gauge pin. What tolerance does the pin provide? The item is specified with a dimensional deviation of ±0.002 mm, suitable for precise fit verification. Which material is used for this pin? The pin is manufactured from special steel, selected for workshop durability. What typical tasks is this pin suited for? Typical applications include end‑dimension checks, fixture set‑up and mating‑part verification in toolrooms and small production runs. Is an ISO 17025 calibration certificate supplied with this item? No ISO 17025 calibration certificate is specified for this item Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
15.4mm Gauge Pin 50mm Length Workshop Version - Metav IndustryLine
Take advantage of the combination of high repeatability, compact dimensions and a ±0.002 mm tolerance for reliable fit checks in workshop settings; the 15.4 mm diameter, 50 mm length inspection pin arrives as a single unit from Metav IndustryLine and is supplied in a protective transport case — order directly via Metav Werkzeuge or request advice from our consultants. Gauge pin, single — 15.4 mm Ø, 50 mm length (Metav IndustryLine) A gauge pin, single — 15.4 mm Ø, 50 mm length designed for precise end‑measurements and go/no‑go fit checks in production and maintenance environments. Precision ±0.002 mm accuracy 15.4 mm nominal diameter fit 50 mm length for end‑measurements Supplied in protective transport case Reproducible checks through tight tolerance and solid material The inspection pin combines a nominal diameter of 15.4 mm with a verified accuracy of ±0.002 mm, enabling repeatable fit and clearance checks in assembly, jigging and final inspection processes. The compact, single‑piece design minimises handling variables while the special steel shaft gives consistent surface hardness and wear resistance. For quality engineers and workshop technicians this translates into faster validation loops and fewer ambiguous results during acceptance tests. Built for workshop use and straightforward handling As a workshop‑grade inspection instrument, the pin is optimised for everyday use where robustness and simple logistics matter. The 50 mm length offers sufficient engagement for most end‑measurement tasks without being unwieldy, and the moderate mass aids stable placement during manual checks. The supply in a protective transport case preserves the reference surface during storage and transit, reducing downtime caused by damaged gauges and ensuring the tool is ready when needed. Practical benefits for inspection and setup workflows Using a dedicated inspection pin or plug gauge streamlines go/no‑go checks and simplifies setup routines for fixtures and housings. The cylindrical geometry and precise diameter support quick verification of bore fits, alignment and end stops. Where documentation of measurement capability is required, the clear numeric tolerance and the product’s identifiable SKU make traceability straightforward across production records and quality control reports. Integration into measurement routines and maintenance plans The single inspection pin is suitable as a reference instrument within a set of workshop gauges or as a stand‑alone check piece in maintenance kits. Its wear characteristics and the special steel composition mean predictable service life under normal workshop conditions; routine inspection of the reference surface is recommended to maintain measurement integrity. The compact format also simplifies storage and reduces the risk of accidental deformation compared with longer or thinner probe tools. Contact Metav Werkzeuge in Emmerich on +49 2822 7131930 or info@metav-werkzeuge.com to discuss technical suitability and supply of the M323.F40 gauge pin Technical data Article number: M323.F40 GTIN: 4061905069666 Material: Special steel Nominal diameter: 15.4 mm Length: 50 mm Weight: 0.1 kg Accuracy: ±0.002 mm Core specifications Single gauge pin (individual supply) Compact 50 mm engagement length Diameter tolerance suited for fit checks Workshop execution for robust use Special features Supplied in a protective transport case Category: Gauge pins (Messstifte) SKU: M323.F40 Brand: Metav IndustryLine FAQ How precise is this gauge pin for fit checks? The gauge pin offers a specified accuracy of ±0.002 mm, making the M323.F40 suitable for reproducible fit and clearance checks in workshop and production environments. What material is the pin made from? The shaft is manufactured from special steel, selected for stability and wear resistance in routine inspection tasks. Is the instrument supplied with protective packaging? Yes, the product is supplied in a protective transport case to safeguard the reference surface during storage and transport. Which applications are typical for this inspection pin? Typical uses include bore fit verification, alignment checks, fixture setup and end‑measurement tasks where a defined 15.4 mm diameter reference is required. Does the item come as a single unit or in sets? This listing is for a single gauge pin (individual supply) under SKU M323.F40, intended for immediate integration into test kits or inspection benches. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
15.51mm Gauge Pin 50mm Length Workshop Finish - Metav IndustryLine
Take advantage of a compact, workshop-grade solution that combines precision and robust handling for routine inspection tasks; the accuracy of ±0.002 mm and the durable special-steel construction support consistent dimensional checks on small bores. Order directly via Metav Werkzeuge or consult our technical team for batch supply and application advice. Test pin M323.F51 — Precision gauge pin, Ø15.51 mm, 50 mm length (Metav IndustryLine) The Test pin M323.F51 is a single-piece, workshop-grade precision gauge pin designed for end-measure and bore verification in metalworking and small-part inspection. Workshop-grade construction Diameter 15.51 mm, length 50 mm Accuracy ±0.002 mm Delivered in protective case Dependable dimensional checks for small bores The cylindrical gauge pin provides a straightforward, repeatable method for verifying bore diameters and end measurements. Constructed for precision, the pin’s nominal diameter of 15.51 mm and the stated accuracy ±0.002 mm make it suitable for routine verification of machined holes, seats and reference gauges where small tolerances are required. Using a solid test pin simplifies go/no-go checks and helps to reduce set-up time on the shop floor by offering a direct physical reference that is easy to compare against drawing tolerances. Robust workshop build for daily use Made from special steel with a workshop-focused finish, this single test pin is intended to withstand frequent handling in production and inspection environments. The construction emphasises wear resistance and dimensional stability, which preserves the reference diameter over many cycles. Supplied in a protective case for transport, the item is ready for safe storage and movement between inspection stations without exposing the measuring surface to accidental knocks or contamination. Practical accuracy and traceable handling With a compact length of 50 mm and a balanced weight for secure handling, the pin is convenient to use across bench and fixture checks. The declared accuracy ±0.002 mm supports fine measurement control for small and medium assemblies, reducing the likelihood of false rejects. For serial inspection tasks, the simplicity of a single precision pin reduces procedural complexity while maintaining a verifiable reference point that integrates smoothly into established quality workflows. Contact Metav Werkzeuge for tailored advice on Metav IndustryLine precision gauge pins and to arrange prompt supply from our Emmerich warehouse. Technical data Article number: M323.F51 GTIN: 4061905071522 Manufacturer: Metav IndustryLine Material: Special steel Feature: Workshop-grade execution Facts Diameter: 15.51 mm Length: 50 mm Accuracy: ±0.002 mm Weight: 0.1 kg Special features Single-piece test pin Delivered in protective plastic or wooden case for transport Suitable for bore and end-measure verification Category: Gauge pins / Messstifte FAQ What is the intended use of this gauge pin? The Test pin M323.F51 is intended for bore diameter checks and end-measure verification in metalworking, providing a simple reference for go/no-go assessments and dimensional comparisons. Is the accuracy specified suitable for shop-floor inspection? Yes, the declared accuracy of ±0.002 mm for the M323.F51 supports precise shop-floor inspections where small tolerances are required. How is the pin protected during transport? The gauge pin is supplied in a protective plastic or wooden case to prevent damage to the measuring surface during transport and handling. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
15.52mm Gauge Pin, Single, 50mm Length, Workshop Version - Metav IndustryLine
Taking advantage of the combination of precise diameter control (15.52 mm), high repeatability with ±0.002 mm accuracy and a compact 50 mm length ensures consistent end‑size verification in workshop inspections; order the gauge pin directly via Metav Werkzeuge or ask our consultants for application advice. Gauge pin M323.F52 — individual test pin, Ø 15.52 mm, length 50 mm (Metav IndustryLine) The gauge pin M323.F52 is an individual test pin for end‑size checks and fixture verification in workshop metrology, designed for reliable daily inspection tasks. Workshop-grade construction for daily use Ø 15.52 mm with ±0.002 mm tolerance 50 mm length for compact fixture checks Fast, measurable control for production and inspection A compact measuring element with a nominal diameter of 15.52 mm and a declared accuracy of ±0.002 mm offers decisive advantages in routine quality control. The tight tolerance reduces uncertainty in pass/fail decisions and shortens inspection cycles, which improves throughput in small‑batch production or repair work. By converting a measured result into an objectively comparable value, the pin supports reproducible decisions and lowers the risk of rework. Robust construction that suits workshop handling Made from special steel, this test pin combines surface hardness and wear resistance with a compact form factor. The 50 mm length and modest mass facilitate handling in confined set‑ups and when checking bores or mating parts on jigs. The workshop-grade configuration prioritises durability and straightforward usability, so that measurement integrity is maintained across repeated insertions without frequent tool replacement. Integrates with simple inspection workflows Delivered as a single item, the pin is suited to ad‑hoc checks, toolroom verification and fixture set‑up work where a precise, repeatable reference is required. The geometry and dimensional specification make it appropriate for end‑size verification of machined components and quick comparative checks on production lines. Traceable identification and the concise specification support inventory management and documentation within a standard inspection protocol. For procurement or technical clarification on the Metav IndustryLine gauge pins, contact Metav Werkzeuge for tailored advice and ordering at +49 2822 7131930 or info@metav-werkzeuge.com Technical data Article number: M323.F52 Label: Gauge pin, individual, 15.52 mm, length 50 mm Brand: Metav IndustryLine Core specifications Diameter: 15.52 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.1 kg GTIN: 4061905071539 Special features Material: Special steel Workshop-grade design Single-piece supply FAQ What tolerance does this gauge pin provide? The gauge pin M323.F52 is specified with a tolerance of ±0.002 mm, enabling precise end‑size verification. Which material is used for the pin? This test pin is manufactured from special steel, chosen for wear resistance and dimensional stability in workshop use. For which applications is the pin suitable? Typical uses include end‑size checks, fixture set‑up and fast comparative inspections of machined components where a compact reference pin is required. Is the pin supplied individually or in sets? The item is supplied as a single, individual gauge pin suitable for immediate use in workshop inspections. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
Fast, tactile checks where electronics are impractical
Gauges and test pins provide unequivocal go/no-go results for threads, bores, gaps and radii without relying on electronics. The range covers plug gauges and ring gauges for internal and external threads, feeler gauges and precision feeler strips for micro‑gap assessment, plus probe pins and measuring pins for tactile diameter and pitch checks.
How these tools work in the production environment
Mechanical gauges operate as direct reference standards: a plug gauge or ring gauge verifies conformity to thread profiles and mating ability, while limit gauges separate accept from reject in a single step. Test pins are used to tactilely measure small bore diameters, centre‑to‑centre distances and radii. Manufactured from hardened gauge steel or ceramic and often precision lapped, these instruments deliver immediate physical results that are ideal for incoming inspection, machine‑side checks and final control.
Measurable benefits that affect production performance
- Reduced scrap and rework through rapid, unambiguous pass/fail assessment.
- Increased repeatability thanks to very low measurement uncertainty and fine lapping.
- Lower downtime: quick checks at the machine save cycle time and reduce setup periods.
- Durable construction with high wear resistance from specialised, low‑distortion alloys.
- Versatile delivery formats: individual gauges, organised sets in wooden cases or metre‑length feeler rolls compliant with DIN 2269.
Why Metav is the practical choice for precision supplies
Metav combines decades of expertise with a broad warehouse and quality filtering from Emmerich. As a precision partner for industry, craft and trade, Metav supplies a comprehensive selection of gauges and test pins alongside complementary tools such as precision calipers and setting rings. With over 48,000 customers and a catalogue exceeding 250,000 items, Metav is positioned to supply reliably, reduce vendor complexity and support traceable quality control to national standards.
Summary
Gauges and test pins are indispensable for dependable, repeatable quality assurance where tactile, mechanical verification is preferred. Choose these plug gauges, ring gauges, feeler strips and probe pins when immediate, robust measurement decisions are required on the shop floor.
FAQ
What materials are gauges and test pins typically made from?
Gauges and test pins are usually manufactured from hardened gauge steel for durability and wear resistance; ceramic variants are available where thermal stability and minimal wear are critical.
How do thread gauges ensure mating capability?
Thread plug gauges and ring gauges check flank diameters and thread form against standards, providing a clear go/no‑go verdict that confirms pairability with mating parts.
Which tolerance class should I choose for probe pins and gauge sets?
Select tolerance classes aligned with your inspection requirements; for high‑precision tasks, sets produced to DIN 2269 or equivalent tolerance classes ensure micrometre‑level control and repeatability.
Can feeler gauges measure contact gaps in valve and engine work reliably?
Yes. Feeler gauges and precision feeler strips, supplied either as a fan or metre‑length rolls, allow accurate assessment of valve clearances and contact gaps down to micrometre increments.
How do limit gauges speed up in‑process inspection?
Limit gauges separate good from bad in a single, tactile operation, enabling rapid go/no‑go checks at the machine and reducing both inspection time and the likelihood of human interpretation errors.
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com