Precision gauge blocks and plug gauges for reliable dimensional control
Mechanical gauge blocks and plug gauges are essential for tactile verification of threads, bores and gap dimensions, providing fast, unambiguous go/no-go results that enhance process reliability and reduce scrap. Designed for industrial metalworking and toolmaking, these precision tools support incoming inspection and final quality checks by delivering traceable measurements in applications such as thread inspection, bore diameter testing and spacing checks. Manufactured from specially hardened, low-distortion alloys and fine-lapped for minimal measurement uncertainty, the range includes thread plug gauges, precision plug gauges and calibration gauge blocks to ensure long-term repeatability and wear resistance.
2 mm Precision Feeler Gauge Set Conical Tips 20-Piece 100mm Length Special Steel - Metav IndustryLine
Taking advantage of a compact 100 mm blade length and a finely graduated thickness range, this set combines precise gap control, durable special steel construction and a practical spread of sizes for routine maintenance and quality checks; order the set directly via Metav Werkzeuge or consult our specialists for application advice. Precision Feeler Gauge Set M318.023 – 0.10–2.00 mm range, 100 mm blades (Metav IndustryLine) The Precision Feeler Gauge Set M318.023 is a workshop-grade tool for rapid, repeatable clearance and gap measurements across maintenance, assembly and inspection tasks Precision blades in special steel Range 0.10–2.00 mm in fine steps 100 mm blade length for stable handling Accurate clearances for efficient production and maintenance This feeler-gauge set delivers reliable measurement for routine checks and setup tasks. With a thickness range of 0.10–2.00 mm presented across 20 blades, the set enables fine incremental selection for valve adjustments, bearing clearances and small-joint inspections. The listed nominal accuracy of ±0.012 mm gives a quantifiable basis for decision-making in quality control, reducing rework and downtime. Because blade lengths are 100 mm, handling is steadier than with very short leaves, so readings are easier to reproduce on comparable components. Robust design that suits demanding workshop conditions Constructed from special steel, the blades resist wear while retaining edge geometry needed for repeatable contact. The set format keeps sizes organised and accessible, supporting fast sequencing during set-up or inspection rounds. Delivered as a complete set, the collection of thicknesses covers common mechanical tolerances and avoids the need for interim shims or improvised gauges. This practical combination of durability and breadth of sizes speeds routine maintenance cycles and contributes to consistent product quality. Practical benefits for users and procurement The compact, lightweight nature of the set supports portability between workstations and makes it straightforward to include in a toolkit or inspection kit. For buyers, the Metav IndustryLine designation signals an industrial focus and a consistent supply chain; Emmerich acts as a quality filter for every delivery. Investing in this precision set simplifies daily checks, lowers the likelihood of assembly errors and supports traceable inspection routines that align with workshop process requirements. For a reliable, workshop-ready precision feeler gauge set from Metav IndustryLine, request the M318.023 via Metav Werkzeuge or contact our consultants at info@metav-werkzeuge.com / +49 2822 7131930 for application support and ordering guidance Technical Data Article number: M318.023 GTIN: 4061905047848 Weight: 0.10 kg Length: 100 mm Pieces per set: 20 Key figures Thickness range: 0.10–2.00 mm Individual thickness steps: 0.10–2.00 mm (various increments) Nominal accuracy: 0.012 mm Set: delivered complete (20 items) Tariff code: 90173000 Materials & features Material: special steel Standard: factory standard Category: feeler gauges / gauges for clearance measurement FAQ What thickness steps are included in the set? The M318.023 set contains blades covering sizes from 0.10 mm up to 2.00 mm in fine incremental steps, providing a versatile spread for common workshop tolerances. Is this feeler gauge set suitable for engine valve adjustments? Yes, the Precision Feeler Gauge Set M318.023 is designed for routine engine and mechanical maintenance tasks where accurate gap measurement between 0.10–2.00 mm is required. How durable are the blades under regular use? Blades are made from special steel for good wear resistance in standard workshop use; proper handling and storage prolong service life. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
2 mm Precision Feeler Gauge Set Tapered Tips 20-Piece Ring Mount, 150 mm Length - Metav IndustryLine
Take advantage of a compact 20-piece set with a 0.10–2.00 mm blade range and tapered geometry to speed gap checks and achieve consistent results; order the set directly via Metav Werkzeuge or contact our consultants for tailored advice. Metav IndustryLine Precision ring-mounted feeler gauge set — 20-piece, 150 mm, tapered blades The Metav IndustryLine Precision ring-mounted feeler gauge set is a workshop-ready gauge kit for fast, repeatable gap and clearance checks in assembly, maintenance and inspection tasks. 20-piece set, blade range 0.10–2.00 mm Tapered blades for narrow-gap access Ring-mounted for secure storage 150 mm blade length for improved reach Faster, measurable checks with industrial precision The set delivers a 0.10–2.00 mm span across 20 pieces, presented in clearly graduated thicknesses to simplify selection and reduce measurement time. With a reported accuracy of ±0.012 mm, the kit supports routine inspection tasks and adjustment work where reliable, repeatable clearance values matter. The combination of compact blade length (150 mm) and fine gradation reduces handling time compared with multiple single gauges, improving throughput on recurring checks while maintaining measurable traceability. Practical design that improves accessibility and safety Each blade features a tapered profile that eases insertion into tight gaps and ensures contact without excessive force, lowering the risk of damage to mating surfaces. The ring-mounted arrangement keeps blades organised and prevents loss while enabling quick access on the bench or in a tool pouch. The blades’ stepped thicknesses make it straightforward to approximate and then confirm fitment values, so technicians can make adjustments with confidence and return assemblies to specification faster. Where this set adds real value in production and service Designed for workshop, maintenance and inspection environments, the set suits everyday tolerance checks, valve and seal clearance verification, and setup work on machines and fixtures. Supplied to Werksnorm, it is intended as a practical, robust solution for tradespeople and toolroom staff who need a compact, reliable gauge set. The modest overall mass supports portability between stations without compromising the feel and control required for precise insertion and verification. Contact Metav Werkzeuge today to discuss delivery options for the Metav IndustryLine set and ensure the gauge selection meets specific workshop requirements Technical data SKU: M318.023.1 GTIN: 4054469164953 Brand: Metav IndustryLine Facts Measurement range: 0.10–2.00 mm Pieces per set: 20 Blade length: 150 mm Blade width: 12.7 mm Weight: 0.34 kg Accuracy: ±0.012 mm Tariff number: 90173000 Standard: Werksnorm Special features Tapered blades (konische Form) Ring-mounted set Blade thicknesses: 0.10 / 0.20 / 0.30 / 0.40 / 0.50 / 0.60 / 0.70 / 0.80 / 0.90 / 1.00 / 1.10 / 1.20 / 1.30 / 1.40 / 1.50 / 1.60 / 1.70 / 1.80 / 1.90 / 2.00 mm Compact, workshop-oriented design FAQ What measurement range does the set cover? The Metav IndustryLine precision ring-mounted feeler gauge set covers a 0.10–2.00 mm range across 20 graduated blades. What accuracy can be expected from the blades? Measured accuracy is stated as ±0.012 mm, which positions the set for reliable workshop inspection and adjustment tasks. How are the blades stored and organised? Blades are ring-mounted for secure storage and rapid access; the tapered geometry and clear graduation speed selection during routine checks. Is the set suitable for on-site maintenance work? Yes — the set’s compact 150 mm blade length and light overall mass make it convenient to carry between work stations and use in field service applications. Does the delivery include a calibration certificate? The product is supplied to Werksnorm; an ISO 17025 calibration certificate is not indicated in the product data. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
2" UNC Go Thread Ring Gauge 2 × 4.5 Pitch ANSI/ASME B1.1 2A - Metav IndustryLine
Take advantage of precise thread acceptance and durable construction: the combination of ANSI/ASME B1.1 conformity, hardened gauge steel and a clear 2A tolerance class ensures reliable go/no-go checks and long service life. Order the gauge directly via Metav Werkzeuge or contact our consultants for application advice. Thread ring gauge UNC GO, 2" x 4.5 TPI (ANSI/ASME B1.1) — Metav IndustryLine A Thread ring gauge UNC GO, 2" x 4.5 TPI for fast verification of external UNC threads in workshop and production environments, designed to the ANSI/ASME B1.1 specification. Hardened gauge steel construction Conforms to ANSI/ASME B1.1/B1.2 Tolerance class 2A acceptance GO ring for external thread verification Reliable acceptance testing to international thread standards This ring gauge is manufactured to the ANSI/ASME B1.1/B1.2 thread form and intended for GO checks against external UNC threads. As a GO gauge it confirms that a thread falls within the allowable maximum material condition for assembly; components that pass the GO test can be confidently assembled without interference. The explicit 2A tolerance class signals the gauge is matched to the common external thread allowance for class 2 fasteners, supporting interchangeability across suppliers and repeatable production acceptance. Built for repetitive use and long-term stability Made from hardened gauge steel, the ring gauge resists wear in high-usage inspection routines and retains thread geometry for many cycles, reducing the need for frequent replacement. The nominal size 2" and the thread pitch 4.5 TPI are clearly identified on the tool for rapid selection at the control station. Its robust construction and balanced mass help maintain concentric engagement during checks, which lowers measurement variation and contributes to consistent quality control in machining and assembly lines. Seamless workflow integration and traceability The ring gauge offers rapid, tactile GO/NO-GO assessment that integrates simply into shop-floor inspections and final inspection checks. Use the gauge to validate batches before assembly, to segregate non-conforming parts quickly, or to confirm corrective actions after tool adjustments. The compact handling and immediate pass/fail result reduce inspection time per part, increasing throughput while maintaining documented traceability through the product SKU and GTIN for inventory and quality records. For assured thread acceptance from a trusted source, request the Metav IndustryLine GO ring gauge via Metav Werkzeuge — our Emmerich team can advise on inventory and technical fitment at info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: M315.967 GTIN: 4054469180588 Label: Thread ring gauge UNC GO, 2" x 4.5 TPI Condition: Good Facts Weight: 0.8 kg Size: 2" Pitch: 4.5 TPI Tolerance class: 2A Features & materials Material: hardened gauge steel Standard: ANSI/ASME B1.1/B1.2 Type: GO ring gauge Category: Gauges / Inspection tools FAQ What is the primary use of this gauge? The thread ring gauge UNC GO, 2" x 4.5 TPI is used to verify external UNC threads quickly by confirming that the thread meets the GO acceptance condition specified in ANSI/ASME B1.1. What does the 2A tolerance class indicate? Tolerance class 2A denotes the commonly used external thread allowance for general-purpose fastening; the gauge is manufactured to that class to ensure compatibility with standard internal threads. How is the GO ring gauge applied during inspection? A component is considered acceptable if it screws onto the GO ring gauge freely without jamming; lack of fit indicates potential oversize or form error requiring rejection or rework. How should wear be checked and when is replacement needed? Inspect the ring for surface degradation or loss of thread form; if engagement becomes inconsistent or marks appear on the workpiece, replace the gauge or have it checked as part of the regular tool control cycle to maintain inspection reliability. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
2" UNC NOGO Thread Ring Gauge 2A 4.5 TPI ANSI/ASME B1.1 - Metav IndustryLine
Take advantage of the combination of standard-compliant inspection capability, hardened gauge-steel construction and clear traceability for reproducible thread checks — order the Thread Ring Gauge UNC NOGO 2" x 4.5 (2A) directly via Metav Werkzeuge or ask our consultants if further specification is required. Thread Ring Gauge UNC NOGO 2" x 4.5 (2A) — Metav IndustryLine A Thread Ring Gauge UNC NOGO 2" x 4.5 (2A) designed for go/no‑go verification of external UNC threads in accordance with ANSI/ASME B1.1/B1.2 for industrial inspection tasks ANSI/ASME B1.1/B1.2 compliant thread gauge Hardened gauge steel construction Tolerance class 2A for external thread acceptance Reliable standard compliance for process control The ring is manufactured to the ANSI/ASME B1.1/B1.2 specification and delivers a consistent method for deciding acceptance or rejection of external UNC threads. As a NOGO member it defines the maximum material limit for a threaded part: a fail on the NOGO indicates oversize material or incorrect thread form. This measurable criterion supports quality plans and reduces subjective judgement during routine inspections, improving reproducibility in batch testing and in-process controls. Robust construction for regular workshop use Made from hardened gauge steel, the gauge resists wear and maintains its functional limit over repeated cycles, which preserves inspection integrity and reduces recalibration frequency. The solid construction and ergonomic ring form allow quick engagement with external threads, speeding up throughput in the workshop. Mass and balance support stable handling; the design suits standard production environments where durability and repeatable contact geometry matter. Clear function and traceability for audits The 2" nominal size with pitch 4.5 and tolerance 2A is expressly intended for external UNC thread verification; the NOGO function helps ensure non‑conforming parts are identified before assembly. Markings and trace data (including SKU) facilitate traceability in quality records and audits. Where statistical process control is used, this fixed‑limit tool provides a simple go/no‑go output that integrates with sampling plans and reduces measurement ambiguity on the shop floor. Choose the Metav IndustryLine ring gauge for consistent, standard‑based thread inspection — contact Metav Werkzeuge in Emmerich at info@metav-werkzeuge.com or +49 2822 7131930 to confirm suitability and place an order. Technical data Article number: M315.997 GTIN: 4054469181226 Weight: 0.9 kg Material: Gauge steel, hardened Standard: ANSI/ASME B1.1/B1.2 Dimensional data Nominal diameter: 2" Pitch: 4.5 Tolerance class: 2A Tariff number: 90173000 Special features Type: UNC NOGO thread ring gauge Use: External thread acceptance checking Category: Gauges / Lehren (thread gauges) SKU: M315.997 FAQ What is the primary purpose of this thread ring gauge? The Thread Ring Gauge UNC NOGO 2" x 4.5 (2A) is intended to perform go/no‑go checks on external UNC threads to determine whether parts meet the specified maximum material and form limits. Which standard does this gauge follow? This ring gauge is manufactured to ANSI/ASME B1.1/B1.2 and therefore provides a standardised acceptance criterion for UNC threads. What does NOGO mean in practical terms? A NOGO ring checks the maximum material condition; if the part enters the NOGO, the external thread is oversize or malformed and must be rejected or reworked. What material is the gauge made from and how does that affect its use? The gauge is made of hardened gauge steel, which enhances wear resistance and longevity, maintaining accurate limits over extended use in production environments. How is the gauge identified for traceability? Identification is provided via the SKU M315.997 and GTIN 4054469181226, which should be recorded alongside inspection results for audit trails. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
2" UNC Thread Go/No-Go Plug Gauge 2B, 4.5 TPI, Hardened Gauge Steel, ANSI/ASME B1.1 - Metav IndustryLine
Take advantage of dependable thread verification with hardened gauge steel and full conformity to ANSI/ASME B1.1; secure consistent production quality and clear acceptance criteria by ordering via Metav Werkzeuge or consulting their specialists for application advice. Thread plug gauge UNC, 2 in × 4.5 tpi — Metav IndustryLine; hardened gauge steel, ANSI/ASME B1.1, 2B The Thread plug gauge UNC, 2 in × 4.5 tpi is a precision inspection gauge designed to verify internal UNC threads to ANSI/ASME B1.1/B1.2 standards with a 2B tolerance classification. Hardened gauge steel construction ANSI/ASME B1.1 compliant Tolerance class 2B 2 in × 4.5 tpi nominal size Consistent acceptance criteria for production control The plug gauge provides a clear, objective method for thread inspection, enabling efficient decisions at the inspection stage. Manufactured from hardened gauge steel, the tool maintains its profile under frequent use, which reduces rework and uncertain measurements. Conformity with ANSI/ASME B1.1 ensures that results are comparable across suppliers and customers, helping to uphold contractual specifications and minimise non‑conformances on the shop floor. Robust construction for repeatable measurements A stable gauge body and heat-treated material mean the instrument resists wear and deformation during routine checking. The 2B tolerance classification denotes standard internal thread acceptance for general engineering applications; using a purpose‑built plug removes operator guesswork and shortens inspection time. The mass and dimensioning aid comfortable handling and consistent seating in threaded bores, supporting a repeatable inspection cycle without elaborate fixturing. Simple to integrate into quality workflows This plug gauge is suitable for inline sampling or bench inspection and fits established quality procedures that reference ANSI/ASME B1.1. Labels and traceable article identifiers simplify inventory management and audit trails. Where traceability is required, the gauge can be logged with its SKU and GTIN for asset control, and routine inspection intervals can be scheduled according to internal quality plans to preserve measurement integrity. Suits standards-driven workshops and suppliers For procurement and inspection teams who prioritise standard compliance and longevity, the gauge offers a pragmatic balance between precision and durability. The UNC designation and 4.5 tpi pitch are commonly specified in mechanical and assembly work, so keeping a calibrated, hardened plug gauge on hand supports faster part acceptance and reduces delays at assembly or receiving. The product is an economical tool for ensuring thread quality across production batches. Contact Metav Werkzeuge today to discuss how the Metav IndustryLine thread plug gauge can be integrated into existing inspection routines or to request application guidance from their specialists at Metav Werkzeuge Technical data Article number: M315.937 GTIN: 4054469179940 Manufacturer: Metav IndustryLine Weight: 0.9 kg Material: Gauge steel, hardened Standard: ANSI/ASME B1.1/B1.2 Tolerance class: 2B Nominal size: 2 in Pitch: 4.5 tpi Core specifications Nominal size: 2 in Pitch: 4.5 threads per inch (tpi) Tolerance: 2B Weight: 0.9 kg Features & compliance Material: Gauge steel, hardened Application: Internal thread verification (UNC) Standards: ANSI/ASME B1.1/B1.2 Category: Thread gauges FAQ What standard does the gauge comply with? The plug gauge conforms to ANSI/ASME B1.1/B1.2, and the Metav IndustryLine thread plug gauge (M315.937) is manufactured to meet those specifications. Which nominal size and pitch are covered by this gauge? This inspection tool is specified for a 2 in nominal size with a 4.5 tpi pitch, suitable for UNC internal thread checks. What does tolerance class 2B mean for inspection? Tolerance class 2B indicates the standard internal thread class for general engineering use; the Metav IndustryLine gauge provides a practical acceptance check against that class. Is the gauge suitable for frequent shop‑floor use? Yes. The hardened gauge steel construction of the Metav IndustryLine thread plug gauge is designed for repetitive inspection and retains its form under normal shop conditions. How is the product identified for inventory and traceability? The item is listed under article number M315.937 and GTIN 4054469179940, which supports straightforward asset tracking in quality systems. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
2,01-3mm Gauge Pin Set 100 Pieces Step 0.01mm in Case - Metav IndustryLine
Highly repeatable gauging and fine gradation make this set ideal for routine quality control and small‑bore verification; the 0.01 mm increments across the 2.01–3.00 mm range ensure rapid identification of out‑of‑tolerance conditions while the robust construction supports long service life. Order the test pin set directly via Metav Werkzeuge or ask our consultants if needed. Test pin set – 100-piece gauge pins, 2.01–3.00 mm, 0.01 mm increments (Metav IndustryLine) A Test pin set for precise plug‑gage checks and repeatable bore verification in metrology and workshop quality control *100-piece set for systematic gauging *Diameter range 2.01–3.00 mm in 0.01 mm steps *Special steel for dimensional stability *Supplied in protective case for transport Faster, more reliable small‑bore inspection The 100-piece set offers a continuous series of gauge pins in 0.01 mm steps across the 2.01–3.00 mm band, enabling fast go/no‑go decisions and minimising adjustment iterations. The fine gradation reduces interpolation and the need for makeshift fits, so process control becomes more efficient and less error‑prone. With an indicated accuracy of ±0.002 mm, these pins support tight tolerance checks where standard workshop checks would otherwise be inconclusive. Durable construction that keeps measurements stable Manufactured from special steel, the pins provide high wear resistance and stable dimensions under normal workshop handling. The material choice prioritises dimensional stability and surface integrity, reducing the frequency of rework or replacement. The set is delivered in a protective case designed for safe transport and organised storage, preserving calibration intervals and keeping the pins sorted for swift retrieval during inspection tasks. Designed for everyday metrology and process integration As a compact, micro‑range solution (Micro classification), the set is tailored for fine mechanical parts, watchmaking, instrument work and precision assemblies where small bores are common. The systematic pin sequence simplifies documentation of pass/fail results and integrates directly with existing inspection routines in machine shops and quality departments. Use of gauge pins shortens inspection time and supports consistent traceability in production control. For reliable dimensional control and practical advice on selecting the right gauge range, contact Metav Werkzeuge for the Metav IndustryLine test pin set M318.552 at info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: M318.552 GTIN: 4054469129358 Manufacturer: Metav IndustryLine Facts Measuring range: 2.01–3.00 mm Increment: 0.01 mm Accuracy: ±0.002 mm Pieces per set: 100 Weight: 1.8 kg Pin length: 50 mm Special features Material: Special steel Supplied in protective case for transport and organised storage Step size per pin: 0.01 mm Classification: Micro range (measuring range up to 10–100 mm) Customs tariff number: 90173000 FAQ What material are the pins made from? The pins in this Test pin set are manufactured from special steel, chosen for wear resistance and dimensional stability. What level of accuracy can be expected? The gauge pins are specified with an accuracy of ±0.002 mm, suitable for fine workshop controls and precision verification. Is the set ready for immediate use upon delivery? Yes, the Test pin set is supplied in a protective case and is ready for immediate use in inspection routines. Which diameter range does the set cover? The set covers gauge diameters from 2.01 mm to 3.00 mm in 0.01 mm increments, enabling close‑spaced checks. Can this set be used for bore checking and plug gauging? The pin sequence and fine step size make the set ideal for plug gauging and rapid bore verification in small components. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
2-3mm Gauge Pin Set 101pcs 70mm 0.01mm Graduation In Plastic Case - Metav IndustryLine
Die 100-piece Pin gauge set M318.852 delivers repeatable small-bore verification thanks to its 2.00–3.00 mm range, 0.01 mm increments and 70 mm pin length, all made from special steel and supplied in a protective case. Order directly via Metav Werkzeuge or consult our specialists for application advice. Pin gauge set M318.852 — precision cylindrical gauges, 2.00–3.00 mm, 0.01 mm steps The Pin gauge set M318.852 is a compact range of precision cylindrical gauges designed for reliable verification of small bores, plug gauges and tooling controls in industrial metrology. High-resolution 0.01 mm increments Range 2.00–3.00 mm 70 mm nominal pin length Supplied in protective case Consistent small-bore verification for production control High-frequency inspection of small holes and bores demands repeatability and straightforward handling. The set’s 0.01 mm step size provides fine gradation for incremental checking across the 2.00–3.00 mm range, reducing guesswork during pass/fail decisions. Made from special steel, each cylinder delivers stable contact geometry so that measurements remain consistent across repeated use, supporting faster quality checks on workpieces, jigs and assemblies. Traceability and measurable precision for integration in QC For systematic quality control, numerically precise increments and a defined nominal pin length of 70 mm ease traceability in inspection reports and preparation of test procedures. The fine graduation aids in establishing clear tolerance bands for small-diameter features. When recorded as part of a measurement routine, the set helps maintain documented verification steps that support internal audits and process stability in machining and assembly operations. Practical handling, storage and workshop suitability The set is supplied in a protective case to keep the gauges organised and protected during transport and storage, improving turnaround in the workshop. At a manageable total weight of 1.82 kg, the set is convenient to carry between bench and machine. The compact format fits inspection stations and reduces setup time when switching between successive checks, contributing to smoother production flow and fewer interruptions. Contact Metav Werkzeuge today for availability, technical clarification and local delivery from Emmerich: info@metav-werkzeuge.com | +49 2822 7131930 — secure the precision pin gauge set that matches inspection requirements. Technical data Article number: M318.852 GTIN: 4061905450174 Material: Special steel Nominal pin length: 70 mm Measuring range: 2.00–3.00 mm Graduation/increment: 0.01 mm Weight: 1.82 kg Supplied in protective case Facts Range min: 2.00 mm Range max: 3.00 mm Increment: 0.01 mm Nominal length: 70 mm Total weight: 1.82 kg GTIN: 4061905450174 Special features Precision cylindrical gauge pins Set format for consecutive diameters Special steel construction Protective transport and storage case FAQ What measurement range does the set cover? The pin gauge set M318.852 covers diameters from 2.00 mm to 3.00 mm in 0.01 mm steps. Are the gauges supplied protected for workshop use? Yes, the M318.852 set is supplied in a protective case to keep the pins organised and secure during storage and transport. Which material are the pins made from? The pins in this set are manufactured from special steel, a material selected for dimensional stability and workshop durability. Is the set suitable for repeatable inspection tasks? The fine 0.01 mm graduation and consistent pin geometry make the M318.852 well suited to repeatable verification and routine quality checks. Can the gauges be used for calibration reference? The set provides precise incremental diameters useful for verification tasks; any formal calibration or certificate requirements should be checked with Metav Werkzeuge to confirm traceability and documentation. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
2.0 mm Limit Gauge Pin H7 DIN 2245 Hardened Gauge Steel - Metav IndustryLine
Data inconsistency detected in the supplied product information. The fields "ausschuss" (marked true) and "gut" (marked true) contradict one another, which creates confusion regarding the product's quality status. Additionally, there is a discrepancy between the weight values provided: the label states "0,01 kg", whereas the numeric field indicates 0.1. These inconsistencies make it difficult to ensure accurate processing and presentation of the product details. Please review and correct these entries to provide consistent and reliable data. Once the corrections are made, a full product description can be generated, ensuring clarity and alignment across all relevant fields.
2.00mm Test Pin Single ±0.001mm Length 50mm, Workshop Version - Metav IndustryLine
Combine workshop‑grade robustness with micrometric tolerance ±0.001 mm and a compact 50 mm length for reliable end‑dimension verification; ideal where repeatable, traceable gauges are required. Order the gauge pin directly via Metav Werkzeuge or ask our consultants if needed. Gauge pin, single — 2.00 mm, ±0.001 mm, 50 mm (Metav IndustryLine) Gauge pin, single — 2.00 mm, ±0.001 mm, 50 mm (Metav IndustryLine) is a precision test pin designed for end‑dimension checks and plug‑gauge applications in workshop and inspection environments Workshop-grade execution Diameter 2.00 mm, tolerance ±0.001 mm 50 mm overall length for end measurements Supplied in protective transport case Precise end‑dimension verification with micrometric repeatability The M323.200 gauge pin offers a nominal 2.00 mm diameter with a guaranteed ±0.001 mm tolerance, delivering the dimensional certainty required for tight clearance and plug‑fit assessments. Such a narrow tolerance reduces rework by ensuring components meet specification at first inspection; the small form factor makes the pin suitable for confined bores and fine mechanical parts. The clearly specified tolerance permits direct comparison against drawing limits and supports objective go/no‑go decisions during assembly and quality control. Robust workshop design for daily inspection routines Built as a workshop‑grade tool, the pin is machined from special steel selected for wear resistance and dimensional stability. The 50 mm length balances reach with rigidity, helping to avoid deflection during insertion. Supplied in a protective case, the measuring pin remains protected in transport and storage, preserving the hardened surface and maintaining long service life. The modest mass also makes the pin easy to handle for repetitive checks, supporting efficient throughput on the shop floor. Streamlined integration into quality control processes The simple geometry of the measuring pin makes it straightforward to incorporate into existing gauge sets, bore gauges and comparison fixtures. Clear identification by SKU and GTIN ensures traceability in inventory and inspection records, while the defined tolerance supports statistical process control and acceptance protocols. Using a standardised test pin like this reduces variation between operators and provides a consistent reference for final‑dimension verification across production batches. Practical handling and inspection benefits Ergonomic handling and a wear‑resistant finish mean quicker measurement cycles and reduced downtime for replacement. The compact design is ideal for small bores and tight features where larger gauges are impractical. Delivered ready for use in a transport case, the pin can be stored safely between shifts and transported between workstations without risk of damage, helping maintain measurement integrity and minimise disruption to inspection workflows. For workshop inspection and reliable end‑measurements, choose the Metav IndustryLine gauge pin M323.200 — contact Metav Werkzeuge for supply and technical advice at info@metav-werkzeuge.com or call +49 2822 7131930 Technical Data Article number: M323.200 GTIN: 4061905056727 Label: Gauge pin, single, 2.00 mm, ±0.001 mm, length 50 mm Manufacturer: Metav IndustryLine Measurements and tolerances Diameter: 2.00 mm Tolerance: ±0.001 mm Length: 50 mm Weight: 0.004 kg Materials and special features Material: Special steel Workshop execution Supplied in protective transport case Category: Gauge pins (Messstifte) FAQ What diameter and tolerance does this pin provide? The gauge pin M323.200 from Metav IndustryLine has a nominal diameter of 2.00 mm with a stated tolerance of ±0.001 mm, suitable for high‑precision end‑dimension checks. Is the pin suitable for repeated workshop use? Yes, the workshop‑grade construction and special steel finish make the pin resilient to frequent handling; it is supplied in a protective case to preserve surface condition between uses. Can this pin be integrated into existing gauge sets? The simple, standard geometry of this measuring pin allows straightforward integration into plug‑gauge holders and comparison fixtures for routine inspection tasks. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
2.01-3.00 mm Gauge Pin Set With Pin Holder 0.01 mm Graduation - Metav IndustryLine
Data inconsistency: the product is labelled as a 101-piece gauge pin set but the provided data lists 100 pieces; this discrepancy raises concerns about the accuracy of the information presented. It is essential to verify the correct set size to ensure that customers receive accurate details about the product they are purchasing. Misrepresentation of the set size could lead to confusion or dissatisfaction among buyers, potentially impacting trust in the product or brand. Please review the data thoroughly and confirm whether the set includes 101 pieces as labelled or 100 pieces as listed before publishing the final product description.
2.01mm Test Pin 50mm Length ±0.001 mm Workshop Version - Metav IndustryLine
Take advantage of precise end‑dimension control with a nominal diameter of 2.01 mm and a verified accuracy of ±0.001 mm; the workshop‑grade special steel construction and 50 mm length ensure stable handling and repeatable inspection results. Order the gauge pin directly via Metav Werkzeuge or consult the technical advisors for specification support. M323.201 — Gauge pin (single) Ø 2.01 mm, ±0.001 mm, 50 mm, Metav IndustryLine M323.201 is a single precision gauge pin intended for fine mechanical inspection and end‑dimension checks in workshop and small‑part inspection environments. Nominal diameter 2.01 mm Tolerance ±0.001 mm Length 50 mm Special steel workshop finish Precision where tight fits matter The M323.201 delivers substantial measurement confidence for micro‑components thanks to a guaranteed dimensional tolerance of ±0.001 mm. Such a narrow allowance is suitable for critical pass/fail checks on mating holes, pin fits and end dimensions where repeatability is paramount. The tight specification reduces rework and helps maintain consistent assembly quality across production batches. By converting nominal diameter and tolerance into predictable inspection outcomes, the pin supports efficient quality control procedures and shortens decision cycles at the inspection bench. Robust material and handling benefits for daily use Constructed from special steel, the pin combines wear resistance with dimensional stability under typical workshop conditions. The 50 mm shaft gives enough engagement depth for most small parts while remaining compact for handheld use and fixture mounting; the balanced length reduces bend and ensures reproducible seating during inspection. Where operators perform many repetitive checks, the material choice and the workshop finish minimise surface wear, maintaining the pin’s functional geometry and preserving calibration intervals. Clear application logic for process reliability Designed for fine mechanical and end‑mass checks, this single gauge pin is aimed at precision shops, toolmakers and quality laboratories performing small‑part verification. The nominal Ø 2.01 mm corresponds to micro‑component inspection ranges and is especially useful for verifying bore sizes, locating holes and validating pin fits in assemblies. Using a dedicated, single‑diameter gauge pin avoids ambiguity in go/no‑go assessments and simplifies insertion checks during incoming inspection or final quality validation. Integration into inspection workflows The pin’s compact geometry and exact tolerance facilitate straightforward use with vises, plug gauges and bench fixtures commonly found in small workshops. Its repeatable performance supports statistical process control by providing consistent reference measurements that feed into capability studies and inspection logs. When recorded in inspection routines, the measured stability from the pin contributes to fewer false rejects and better traceability of dimensional trends in serial production. Contact Metav Werkzeuge today to specify the M323.201 for precision end‑dimension checks and secure supply from Emmerich. Technical data Article number: M323.201 GTIN: 4061905056734 SKU: M323.201 Numbers Length: 50 mm Nominal diameter: 2.01 mm Accuracy / tolerance: ±0.001 mm Weight: 0.004 kg Special features Workshop version Material: Special steel Category: Gauge pin / Test pin FAQ What inspection tasks is this gauge pin suited for? The M323.201 gauge pin is intended for fine mechanical inspections such as bore checks, pin‑fit tests and end‑dimension verification on small components where a 2.01 mm reference is required. How precise is the M323.201 for routine quality control? With a tolerance of ±0.001 mm, the M323.201 provides high repeatability suitable for tight tolerance checks and reliable pass/fail decisions in production control. Can the gauge pin be used in fixtures or plug assemblies? Yes. The 50 mm length and workshop finish make the pin suitable for fixture mounting and use in assembly jigs, enabling consistent seating and repeatable measurement conditions. What maintenance keeps the pin in specification? Routine cleaning and protection from abrasive contamination will preserve the surface and geometry; periodic inspection against a calibrated master ensures continued dimensional conformity. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
2.02mm Gauge Pin Single ±0.001mm Length 50mm Workshop Version - Metav IndustryLine
Take advantage of the combination of industrial‑grade accuracy (±0.001 mm), a stable 2.02 mm diameter and a compact 50 mm length to ensure reproducible end‑measurements and fast fit checks on the shop floor. Order the gauge pin directly via Metav Werkzeuge or consult our specialists for application advice. Gauge pin M323.202 – single test pin, 2.02 mm diameter, ±0.001 mm accuracy (Metav IndustryLine) The gauge pin M323.202 is a compact workshop test pin designed for precise end‑measurements and fit verification in confined or series inspection tasks. High‑precision ±0.001 mm tolerance Compact 2.02 mm diameter for fine fits Robust special steel construction 50 mm length for secure contact and reach Precision that secures assembly tolerances A high degree of measuring certainty is essential for reliable parts inspection. With a declared tolerance of ±0.001 mm, this single test pin provides the metrological stability required for micro‑fits, plug gauges and end‑measure checks. The small nominal diameter of 2.02 mm makes the component suitable for tight bores and fine mechanical interfaces; the narrow profile reduces interference during insertion and supports fast, repeatable checks. The combination of these features helps to reduce rework and process variability in routine quality control. Built for repeatable inspection and fast go/no‑go checks The elongated 50 mm shaft delivers secure engagement with the measured feature and permits consistent contact geometry on every measurement. At approximately 0.004 kg, the element is light enough for handheld gauging yet rigid enough to avoid unwanted bending during short, repetitive operations. The workshop specification ensures a balance between robust handling and dimensional integrity, so the pin is effective for both bench and fixture use when verifying end dimensions or mating fits. Integrates into existing measurement routines with minimal setup Designed as a single, purpose‑driven test element, this gauge pin slots into established inspection routines without the need for special adapters. Its compact size allows access to restricted zones that larger gauges cannot reach, while the straightforward geometry simplifies traceability in inspection logs. Using a standard, single‑element pin speeds up cycle times for checks that would otherwise require more complex tooling, supporting lean inspection workflows and faster throughput. Durable material choice and dependable provenance Manufactured from special steel, the pin resists wear under normal contact use and maintains dimensional stability across repeated cycles. As part of the Metav IndustryLine, the component benefits from a supplier network focused on dependable supply and consistent quality control—attributes that matter when the same gauge is used across multiple shifts and operators. For applications where traceability or certification is required, Metav Werkzeuge can advise on calibration options and documentation to match quality‑management needs. For proven small‑diameter gauging components from Metav IndustryLine, contact Metav Werkzeuge for technical guidance and order processing — rapid supply from Emmerich ensures the test pin reaches the workshop when required. Technical Data Article number: M323.202 GTIN: 4061905056741 Manufacturer: Metav IndustryLine Core technical data Diameter: 2.02 mm Length: 50 mm Tolerance/accuracy: ±0.001 mm Weight: 0.004 kg Special features Material: special steel Version: workshop execution Application: end‑measurements, fit verification Story trigger: end measurements FAQ What level of accuracy does this test pin offer? The gauge pin M323.202 is specified with an accuracy of ±0.001 mm, making it suitable for high‑precision end‑measurements and fit checks in workshop inspection routines. Is the pin suitable for use in small bores or threaded holes? Yes. The 2.02 mm diameter and compact profile are specifically intended for narrow bores and fine fit verifications where access is restricted. What material is the pin made from and how durable is it? The shaft is manufactured from special steel, selected to retain dimensional stability and resist wear under normal inspection cycles. Can the pin be used in fixture or bench‑mounted gauges? The 50 mm length and robust shaft permit integration into simple fixture setups or handheld checks; Metav Werkzeuge can advise on fixturing options for series testing. Does the product come with manufacturer identification for traceability? The product is supplied as part of the Metav IndustryLine range (SKU M323.202, GTIN 4061905056741), which supports traceability in documented inspection procedures. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
2.03mm Gauge Pin Length 50mm ±0.001mm, Workshop Version - Metav IndustryLine
Take advantage of the combination of ultra‑fine tolerance, compact form and workshop‑ready protection for repeatable end‑measure checks. Order directly via Metav Werkzeuge or consult our specialists for specification support and rapid delivery. Gauge pin M323.203 – 2.03 mm ±0.001 mm, 50 mm length (Metav IndustryLine) The gauge pin M323.203 is a precision reference pin for end‑measure checking and fixture setting in metrology and workshop inspection. Precision diameter 2.03 mm ±0.001 mm 50 mm special steel shaft Workshop version with transport box Consistent reference for end‑measure and plug‑gauge tasks A compact reference element with a 2.03 mm nominal diameter and ±0.001 mm tolerance, this pin provides a stable benchmark for repeatable end‑measure checks and go/no‑go testing. The fine tolerance reduces uncertainty when dimensioning small bores or aligning precision fixtures, which lowers rework rates and shortens inspection cycles. The small mass and simple geometry make it straightforward to integrate into pin stacks or master gauge sets while maintaining consistent contact conditions. Robust handling and protected transport for shop use Designed as a workshop edition, the pin is made from special steel and supplied in a protective transport box to preserve the measuring surface during storage and shipment. The form‑stable shaft and clean finish minimise surface damage and ensure longevity under regular use. The product’s low weight and slim profile support rapid handling on the shop floor and reduce operator fatigue when performing repetitive reference measurements. Fast integration into quality workflows and fixture setups As a dedicated gauge element, the pin supports quick fixture setting, alignment and verification tasks without complex preparation. Its precise diameter is suited to fine bore checks and comparator fixtures, enabling technicians to make immediate pass/fail decisions and maintain throughput. Using standardised reference pins in inspection sequences simplifies documentation and contributes to stable process capability metrics. Choose the Metav IndustryLine gauge pin M323.203 for precise, repeatable end‑measure work and contact Metav Werkzeuge for tailored advice and reliable dispatch from Emmerich Technical data Article number: M323.203 GTIN: 4061905056758 Label: Gauge pin, single, 2.03 mm, ±0.001 mm, length 50 mm Facts Diameter: 2.03 mm Length: 50 mm Tolerance/accuracy: ±0.001 mm Weight: 0.004 kg Special features Material: special steel Workshop version Delivery: transport box FAQ What material is the gauge pin made from? The Metav IndustryLine gauge pin M323.203 is manufactured from special steel for stable dimensions and wear resistance in routine inspection tasks. Is the pin supplied with a calibration certificate? The gauge pin M323.203 is supplied as described; a calibration certificate is not included in the standard delivery unless explicitly stated for the specific product version. Can this pin be used for small bore inspection and setting of fixtures? Yes, the 2.03 mm diameter and tight ±0.001 mm tolerance make it suitable for small bore checks and for use as a reference when setting inspection fixtures and pin stacks. How should the gauge pin be stored to maintain accuracy? Store the pin in its transport box and avoid contact with abrasive surfaces or corrosive environments; keep in a dry, temperature‑stable location to preserve surface integrity and dimensional stability. Is the gauge pin suitable for repeated shop‑floor use? The workshop design and protective packaging of the Metav IndustryLine gauge pin M323.203 support regular shop‑floor use; the special steel construction balances durability with precision. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
2.04mm Gauge Pin Length 50mm ±0.001mm Workshop Version - Metav IndustryLine
Take advantage of the combination of extreme precision, workshop-hardy design and compact handling for reliable in-process checks; order the test pin directly via Metav Werkzeuge or consult our specialists for tailored inspection setups. Test pin M323.204 — single precision probe, 2.04 mm diameter, ±0.001 mm Test pin M323.204 is a compact inspection probe for pinpoint dimensional checking in precision workshops and quality departments. Workshop grade, robust design High precision ±0.001 mm tolerance Diameter 2.04 mm for fine measurements Compact length 50 mm for tight spaces Precision checking for micro components that saves rework The M323.204 test pin is designed for micro-range verification where smallest deviations matter: with a nominal diameter of 2.04 mm and a tolerance of ±0.001 mm, this probe provides repeatable contact checks for small bores, pin gauges and end measurements. Manufactured from special steel, the probe resists wear while keeping surface contact stable; the compact 50 mm length aids access to confined features. Engineers benefit from clearer go/no-go decisions and fewer rejected parts thanks to the pin’s consistently tight tolerances. Workshop robustness plus traceable inspection routines Built as a workshop-execution instrument, the probe balances hard-wearing construction with metrological accuracy. The fine tolerance reduces uncertainty in routine inspection, cutting down cycle time for batch sampling and supporting quicker process adjustments. Where traceable records are required, the pin serves as a reliable reference element within fixture checks and end‑of‑line control sequences. The compact geometry makes it suitable for handheld gauges as well as fixed checking fixtures, enabling integration into existing measurement stations without major rework. Simple handling, clear fit into measurement systems Handling remains straightforward: the small mass and short shank ease positioning, while the hard steel construction tolerates repeated contact. The probe is suited to component classes in toolmaking, small-part assembly and precision engineering that demand micro-scale verification. For compatibility, the item can be used alongside standard gauge holders and depth stops; careful mounting ensures the ±0.001 mm performance is translated into reliable plant-level results. The clear specification of diameter and length supports documentation and part traceability during audits. Contact Metav Werkzeuge for advice on integrating the M323.204 into inspection workflows or to request ordering information through our Emmerich supply channel Technical data Article number: M323.204 GTIN: 4061905056765 Manufacturer: Metav IndustryLine Facts Diameter: 2.04 mm Length: 50 mm Tolerance: ±0.001 mm Weight: 0.004 kg Special features Material: special steel Workshop execution High-precision finish Suitable for fine bore and end‑measure checks FAQ What applications suit this test pin best? The M323.204 test pin from Metav IndustryLine is intended for fine bore checks, end‑measure verification and precision fixture testing where a 2.04 mm diameter probe with ±0.001 mm tolerance is required. Is the pin suitable for repeated contact in a production environment? Yes, the workshop‑grade construction and special steel material make the probe resilient to repeated use, ensuring dimensional stability across inspection cycles. Can the probe be used with standard gauge holders? The probe’s compact 50 mm length and standardised shank dimensions allow it to be mounted in common gauge holders and fixture systems without additional modification. How is measurement uncertainty managed when using this probe? Manage uncertainty by securing the probe to a stable holder, controlling contact force during measurement and performing regular fixture checks; the probe’s ±0.001 mm tolerance provides a tight baseline for such procedures. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
2.05mm Gauge Pin 50mm Length ±0.001mm Workshop Version - Metav IndustryLine
Take advantage of the combination of ultra-fine one-micron tolerance, a compact 50 mm length and robust workshop construction for reliable end measurements; order directly via Metav Werkzeuge or request technical advice from our specialists. M323.205 gauge pin — 2.05 mm diameter, ±0.001 mm, 50 mm length (Metav IndustryLine) The M323.205 gauge pin is a workshop-grade inspection pin designed for precise end measurements and integration into fixtures and jigs. Ultra-fine tolerance ±0.001 mm Diameter nominal 2.05 mm Length 50 mm for end measurements Workshop-grade special steel construction Dependable one‑micrometre accuracy for quality control The inspection pin delivers a certified mechanical tolerance of ±0.001 mm, corresponding to a resolution at the 1 µm level that supports high-precision go/no-go checks and micrometric inspections. Such repeatable accuracy reduces measurement uncertainty in sampling and control operations, enabling faster decisions on conformity. The narrow tolerance makes this pin particularly suitable where dimensional consistency is critical, for example when validating pin gauges, assembly fits or small-bore seating in routine workshop inspections. Robust workshop construction that withstands daily use Built as a workshop-grade item from special steel, the pin combines wear resistance with consistent performance under regular handling. The material choice gives a reliable surface that resists deformation during insertion and withdrawal, which in turn preserves the geometric integrity of the nominal 2.05 mm diameter over many cycles. The compact weight and balanced geometry facilitate safe manual handling and make the component easy to seat in fixture pockets or controlled instrument holders. Compact form for precise end‑measurement applications At a length of 50 mm and a nominal diameter of 2.05 mm, the pin is optimised for end‑measurements and tight‑tolerance checks in small assemblies. Its small form factor allows straightforward integration into test rigs and makes it a practical choice for bench inspection tasks and inline fixtures alike. The low mass contributes to controlled insertion dynamics, helping to avoid measurement artefacts from impact or excessive force while delivering consistent contact conditions across repeated checks. For technical advice or to request the M323.205 from the Metav IndustryLine range, contact Metav Werkzeuge in Emmerich at info@metav-werkzeuge.com or call +49 2822 7131930 Technical data SKU: M323.205 GTIN: 4061905054471 Brand: Metav IndustryLine Core specifications Diameter: 2.05 mm Length: 50 mm Tolerance: ±0.001 mm Weight: 0.004 kg Features Material: special steel Workshop version Supplied individually Application: end measurements FAQ What tolerance does this gauge pin offer? The M323.205 gauge pin from Metav IndustryLine is specified with a tolerance of ±0.001 mm, suitable for micrometric inspection tasks. What material is used for the pin? This inspection pin is manufactured from special steel, chosen for its wear resistance and stability under workshop conditions. For which applications is this pin intended? The pin is intended for end measurements, fixture checks and small‑bore inspections where a nominal 2.05 mm diameter and one‑micrometre tolerance are required. Can the pin be used in inspection jigs and fixtures? Yes — the 50 mm length and compact form factor make the pin suitable for integration into test rigs and bench fixtures in routine quality control. How is the product identified for ordering? Order reference is SKU M323.205; the product is listed under the Metav IndustryLine range and carries GTIN 4061905054471. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
2.06mm Gauge Pin, ±0.001mm Accuracy, 50mm Length, Workshop Version - Metav IndustryLine
Reliable inspection requires both fine tolerance and durable construction: benefit from the combination of a ±0.001 mm tolerance, special steel hardness and a practical protective case for safe transport; order the gage pin directly via Metav Werkzeuge or ask our consultants for application advice. Gage pin M323.206 — 2.06 mm, ±0.001 mm, 50 mm The Gage pin M323.206 is a precision measuring pin for verifying end dimensions and bore fits in workshop metrology, designed as a robust workshop version for routine inspection tasks. High-precision ±0.001 mm tolerance Diameter 2.06 mm for tight bore checks Length 50 mm workshop design Delivered in protective case Precision where measurement matters A finely matched tolerance is the core benefit when checking bore sizes or end dimensions. The ±0.001 mm specification guarantees a high level of reproducibility for pass/fail checks and comparative inspections, reducing guesswork during quality control. For everyday workshop routines, a narrow tolerance helps to avoid rework and scrap by making acceptance criteria clear and repeatable. Robust workshop design for repeated handling Engineered as a workshop-grade instrument, the pin uses special steel to withstand frequent use and handling. The 50 mm length offers a secure grip and adequate engagement depth for most small-bore verifications, while the compact mass facilitates quick positioning. Delivery in a protective case ensures safe transport between benches or job sites, protecting the measuring surface from knocks and contamination that could otherwise affect accuracy. Simple integration and traceability in inspection workflows The test pin is suitable for quick plug checks, end-dimension verification and assembly validation in production and maintenance settings. Marked and traceable with SKU M323.206 and GTIN details, the component can be recorded in inspection logs and inventory systems for audit-friendly traceability. The compact geometry and industry-standard dimensions allow easy use with comparison fixtures and visual inspection jigs, improving throughput without complex set-up. Choose the Metav IndustryLine M323.206 for dependable bore verification and contact Metav Werkzeuge GmbH in Emmerich at info@metav-werkzeuge.com or +49 2822 7131930 for availability and expert guidance Technical data SKU: M323.206 GTIN: 4061905054488 Manufacturer: Metav IndustryLine Facts Diameter: 2.06 mm Tolerance: ±0.001 mm Length: 50 mm Weight: 0.004 kg ECLASS: 21170231 Special features Workshop version Delivered in protective case for transport Material: special steel Suitable for verification of end dimensions and bore fits FAQ What tolerance is specified for this gage pin? The gage pin is specified to ±0.001 mm, offering high repeatability for precise bore and end-dimension checks with SKU M323.206. Which materials is the pin made from? The pin is made of special steel, selected for wear resistance and durability under frequent workshop use. Is the pin supplied ready for transport? Yes, the item is delivered in a protective case intended for safe transport and to preserve the measuring surface. For which inspection tasks is this pin best suited? This pin is ideal for plug checks, verification of end dimensions and quick bore checks in production and maintenance environments. How can this test pin be recorded for traceability? Use the SKU M323.206 and GTIN 4061905054488 in inspection logs and inventory systems to maintain traceable records. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
2.07mm Gauge Pin Single, ±0.001mm, 50mm Length, Workshop Version - Metav IndustryLine
Taking advantage of high repeatability, submicrometre tolerance and a compact length, this test pin ensures repeatable dimensional checks in workshop and inspection tasks; combine robustness and precision for smoother quality routines. Order the gauge pin directly via Metav Werkzeuge or ask our consultants if needed. Gauge pin M323.207 — 2.07 mm diameter, ±0.001 mm tolerance (Metav IndustryLine) The M323.207 is a single test pin designed for precise dimensional inspection and fixture setting across metrology and production environments. Workshop-grade construction Diameter 2.07 mm with ±0.001 mm tolerance Length 50 mm for compact checks Supplied as a single test pin Reliable precision for routine inspection The compact gauge element delivers a 2.07 mm nominal diameter with an exceptional ±0.001 mm tolerance, making it suitable where tight limits are required in small bores or pin gauges. Manufactured as a workshop-grade tool, the component supports consistent pass/fail assessment and short-cycle quality checks. The combination of close tolerance and moderate length reduces deflection risk during use, which translates into fewer measurement repeats and more efficient inspection throughput. Robust material and practical handling Constructed from special steel, the pin balances surface hardness with corrosion resistance to withstand frequent handling and insertion cycles on the shop floor. The 50 mm length is intentionally compact to suit fixture set-up, gauge blocks and pin plates while keeping handling simple. At approximately 0.004 kg, the part is easy to position and integrate into existing inspection jigs. The solid design minimises burr-related errors and affords long-serving dimensional stability under normal workshop conditions. Integration into quality workflows As a single-item solution, the component is well suited for selective checks, calibration aids and fixture references where a dedicated nominal diameter is required. Traceable identification via SKU and GTIN facilitates stock control and documentation in quality management systems, while the clear specification supports supplier audits and inspection planning. Metav IndustryLine provides the necessary product data for procurement and inspection documentation to maintain repeatable measurement routines. For workshop-grade dimensional control, contact Metav Werkzeuge in Emmerich to secure the M323.207 gauge pin and discuss supply options or technical details. Technical data Article number: M323.207 GTIN: 4061905054495 Manufacturer: Metav IndustryLine Facts Diameter: 2.07 mm Length: 50 mm Tolerance: ±0.001 mm Weight: 0.004 kg Special features Material: Special steel Version: Workshop version Delivery form: single test pin Category: Gauge pins FAQ What is the primary use of this test pin? The M323.207 is intended for precise dimensional checks, fixture setting and selective inspection tasks where a defined nominal diameter of 2.07 mm is required. How accurate is the pin for quality checks? The pin is specified with a tolerance of ±0.001 mm, suitable for tight tolerance checks and applications that demand sub-micrometre repeatability. What material is the pin made from and is it durable? The component is made from special steel and delivered in a workshop-grade design, giving good wear resistance and durability for regular use in production environments. Is a calibration certificate supplied with this item? No calibration certificate is specified in the product data for this item Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
2.08mm Gauge Pin Single, ±0.001mm, 50mm Length, Workshop Version - Metav IndustryLine
The combination of high repeatability, submicron tolerance and a compact 50 mm form factor ensures reliable end‑measure checks and straightforward integration into workshop test fixtures. Order the gauge pin directly via Metav Werkzeuge or consult the team for specification matching. Gauge pin M323.208 — 2.08 mm diameter, ±0.001 mm, 50 mm length (Metav IndustryLine) A single, precision gauge pin designed for exact end‑measure references and workshop inspection tasks, supplied as an individual test pin for fixture setting and quality control. Workshop version for robust handling Diameter 2.08 mm with ±0.001 mm accuracy 50 mm special-steel construction Reliable reference for repeatable measurements The M323.208 gauge pin provides a stable reference for end‑dimension verification and fixture alignment. Manufactured in a workshop execution, the pin combines compact geometry with machining that prioritises consistent contact surfaces; this results in repeatable positioning when used for plug checks or in assembly jigs. The documented ±0.001 mm tolerance supports narrow acceptance windows in precision production and reduces the risk of rework caused by measurement variation. Precision explained and practical benefits A declared tolerance of ±0.001 mm places the gauge pin in a high‑precision category suitable for fine inspection tasks and fit verification. In practice, this means the pin can be used to establishing reference points where dimensional certainty is critical; the tight tolerance reduces measurement uncertainty and supports faster decision‑making in process control. The small diameter of 2.08 mm and the 50 mm length make the component especially suitable for compact bores, dowel checks and contact probing where minimal intrusion and high positional accuracy are required. Durable material and workshop suitability Constructed from special steel, the pin combines surface hardness with resistance to wear typical of workshop environments; this supports sustained dimensional integrity over repeated use. The single‑piece supply, low mass (approx. 0.004 kg) and precise machining enable easy handling and rapid interchange in test setups. The robust finish and geometry are tailored to withstand regular insertion without immediate loss of accuracy, supporting consistent inspection routines and minimising machine downtime. For reliable workshop calibration and procurement of the Metav IndustryLine M323.208 gauge pin, contact Metav Werkzeuge for ordering and technical guidance at info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: M323.208 GTIN: 4061905054501 Brand: Metav IndustryLine Label: Prüfstift, einzeln, 2,08mm, +/- 0.001 mm Länge 50 mm Numerical data Diameter: 2.08 mm Length: 50 mm Declared accuracy: ±0.001 mm Weight: 0.004 kg Materials & features Material: Special steel Delivery: Single gauge pin Version: Workshop execution Intended use: End‑measure reference / fixture and inspection tasks FAQ What tolerance does the gauge pin have? The gauge pin is specified with an accuracy of ±0.001 mm, allowing high‑precision end‑measure checks with narrow acceptance limits. Which materials is the M323.208 suitable for inspecting? The M323.208 gauge pin is a reference component for dimensional checks and is applicable when verifying bores, dowel seats and fixture positions irrespective of workpiece material. Is the pin supplied as a single item or in sets? This article is supplied as a single gauge pin (individual delivery); the designation and SKU are M323.208. How durable is the material under frequent use? Made from special steel, the pin is produced for workshop environments and offers wear resistance appropriate for repeated insertion and inspection cycles. Can the M323.208 be used for precision probing in measuring machines? Yes; the small diameter and tight tolerance make the gauge pin suitable as a contact reference for manual and machine‑assisted inspection setups. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
2.09mm Gauge Pin, Workshop Version, ±0.001mm Accuracy, 50mm Length - Metav IndustryLine
Take advantage of the combination of ±0.001 mm accuracy, a compact 2.09 mm diameter and a robust 50 mm length for reliable small‑bore inspection and repeatable end‑measurements; order the gauge pin directly via Metav Werkzeuge or consult the technical team for application advice. M323.209 Gauge pin (2.09 mm, ±0.001 mm) – Metav IndustryLine The M323.209 gauge pin is a single, high‑precision inspection pin designed for small‑bore verification and end‑measurements in workshop and inspection environments. High accuracy ±0.001 mm 2.09 mm diameter for fine bores 50 mm length for reliable reach Workshop version for robust handling Highest measurement confidence for small bores Engineered for tasks where small dimensional deviations matter, this pin delivers a ±0.001 mm positional tolerance that classifies it as a high‑precision inspection tool. Such tolerance helps reduce rejects and rework by providing a clear go/no‑go reference for tight fits. The fine 2.09 mm diameter makes it suitable for verification of small holes, plug gauges and end stops where conventional gauges are too coarse. Durable design that supports everyday metrology Constructed from special steel and specified as a workshop version, the pin combines surface hardness with a finish optimised for repeatable contact. The 50 mm length provides sufficient reach for many bench and fixture checks while maintaining stiffness to avoid deflection. These properties translate into reliable measurements over many cycles and minimise downtime linked to premature wear. Practical use in inspection and production workflows Ideal for inspection benches, jigs and assembly verification, the single‑piece pin simplifies inventory and traceability in quality processes. Its compact form factor allows easy integration into gauge sets and takedown checks. The robust construction supports frequent handling in production areas, and the clearly defined tolerance assists metrology teams in documenting conformity during incoming inspection and in‑process checks. For specialist advice or to arrange supply of the M323.209 gauge pin, contact Metav Werkzeuge in Emmerich for tailored technical guidance and prompt delivery. Technical data Article number: M323.209 GTIN: 4061905054518 Manufacturer: Metav IndustryLine Facts Diameter: 2.09 mm Length: 50 mm Tolerance: ±0.001 mm Weight: 0.004 kg Special features Material: Special steel Workshop version Single test pin FAQ What is the primary use of this gauge pin? The M323.209 gauge pin is intended for small‑bore verification and end‑measurement tasks in workshops and inspection areas. What precision class does the pin belong to? With a tolerance of ±0.001 mm, the pin falls into the high‑precision inspection category suitable for fine metrology checks. Which materials is the pin suitable for when used as a reference? The pin serves as a dimensional reference for bore and end‑measure checks and can be used alongside components made from a wide range of materials; selection of mating materials should follow usual metrological practice. Is the M323.209 suitable for integration into gauge sets? Yes, its compact form and defined length make it suitable for gauge sets, fixtures and inspection benches where small‑bore references are required. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
2.10mm Test Pin Single ±0.001 mm Accuracy Length 50 mm Workshop Version - Metav IndustryLine
Take advantage of the combination of micrometre-grade accuracy, robust workshop design and practical transport packaging for reliable end-dimension checks. Order the gauge pin directly via Metav Werkzeuge or ask the Metav consultants for application advice. Metav IndustryLine gauge pin M323.210 — 2.10 mm, ±0.001 mm, 50 mm length A Metav IndustryLine gauge pin for precise end-dimension verification in workshop and inspection environments, designed as a single-piece, workshop-grade test pin for micromechanical checks. Workshop version for durable everyday use Diameter 2.10 mm with ±0.001 mm tolerance 50 mm length for end-dimension verification Supplied in transport case for secure handling Measure end dimensions with micrometre-class certainty A test pin with a nominal diameter of 2.10 mm and a tolerance of ±0.001 mm delivers measurable, repeatable outcomes for tight-fit and finishing checks. The listed tolerance is a technical specification that directly reduces uncertainty in go/no-go assessments and gauge-based inspection routines. Where component fits matter, the reduced dimensional scatter shortens decision loops in production control and lowers the risk of rework. The combination of small diameter and fine tolerance positions this pin within the micro-range expected for precision bench and component work. Built for the workshop: robust material and safe transport Constructed from special steel and rated as a workshop version, the pin tolerates routine handling while retaining its measuring geometry. The 50 mm overall length provides adequate grip for insertion and withdrawal without compromising alignment when checking bores or mating parts. Delivery in a transport case (plastic or wooden) protects the gauge during storage and transit, preserving the measured surface and minimising the need for frequent rework or replacement. The single-piece format simplifies handling and reduces potential assembly errors that could otherwise affect measurement consistency. Practical integration into inspection workflows This precision test pin is intended for end-dimension and fit verification on small bores, jigs, and assembled components. Traceability is supported by the product identifiers included in the technical data, enabling simple inventory control and record-keeping for quality systems. As a compact measuring implement, it complements bench calipers and micrometres by providing a direct physical reference for mating features, accelerating in-process checks and pass/fail assessments. The design focuses on a single, well-defined task—reliable verification of critical diameters—so inspection steps remain straightforward and efficient. For application guidance or to source the Metav IndustryLine gauge pin M323.210 for your inspection bench, contact Metav Werkzeuge in Emmerich by email at info@metav-werkzeuge.com or by phone on +49 2822 7131930 to discuss suitability and delivery options Technical data Article number: M323.210 GTIN: 4061905054525 Weight: 0.004 kg Material: Special steel Nominal diameter: 2.10 mm Tolerance: ±0.001 mm Length: 50 mm Facts Diameter (nominal): 2.10 mm Tolerance: ±0.001 mm Length: 50 mm Weight: 0.004 kg GTIN: 4061905054525 Special features Workshop version Single-piece gauge pin Supplied in transport case (plastic or wood) for secure handling Intended for end-dimension verification FAQ What tolerance does this gauge pin offer? The gauge pin provides a tolerance of ±0.001 mm, enabling micrometre-level control for end-dimension checks. Is the pin suitable for routine workshop use? Yes; the workshop-grade construction and special steel material make the pin robust enough for regular inspection tasks. What is the length and how does that affect handling? At 50 mm length the pin offers a practical balance between handling comfort and measurement stability for manual checks. Can this pin be used for go/no-go checks on small bores? It is suitable for direct diameter verification and go/no-go style assessments where a 2.10 mm reference is required. How is the product identified for inventory and traceability? The product is listed as Metav IndustryLine gauge pin M323.210 with GTIN 4061905054525 for straightforward traceability. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
2.11mm Gauge Pin, Single, ±0.001mm, 50mm Length, Workshop Version - Metav IndustryLine
Benefit from the combination of industrial accuracy and workshop durability: the M323.211 precision gauge pin delivers a ±0.001 mm tolerance on a 2.11 mm diameter with a 50 mm functional length, enabling reliable end-dimension checks in routine quality control. Order directly via Metav Werkzeuge or consult our advisors for application support. M323.211 — precision gauge pin, 2.11 mm diameter, ±0.001 mm (Metav IndustryLine) The M323.211 is a single precision gauge pin designed for end-dimension verification and small-part inspection in workshop and laboratory quality-control environments. Workshop version for rugged everyday use Diameter 2.11 mm with ±0.001 mm tolerance 50 mm functional length for deep measurements Supplied in transport case for secure storage Accurate control for repeatable quality A gauge pin with a ±0.001 mm tolerance provides sub-micron-level repeatability that supports tight production tolerances and reduces scrap rates. The very small diameter of 2.11 mm makes this instrument suitable for fine bores and micro features where standard plugs cannot access. By offering a defined reference diameter and a stable length of 50 mm, the pin enables consistent pass/fail checks and comparative measurements that align with industrial metrology practices, improving process control and reducing measurement uncertainty. Built for workshop handling and longevity Manufactured from special steel and specified as a workshop version, the pin balances hardness and corrosion resistance to withstand frequent use. The compact mass and slim geometry allow easy handling during rapid inspection routines, while the supplied transport case protects the gauge during storage and transit. Robust design minimises deformation risk during everyday use, giving reliable reference points across many inspection cycles and supporting efficient inspection flows in busy production environments. Micro-class suitability and application scenarios With a maximum measuring range of 2.11 mm, this pin falls into the micro class of measuring tools, developed for fine mechanical assemblies, micro components and precision fixtures. Typical uses include verification of small-bore diameters, calibration of holding fixtures, end-dimension checks for turned parts and comparative gauging in inspection benches. The compact dimensions and high tolerance make the instrument a practical choice where tight fits and fine geometries are common. Practical integration and operational benefits The instrument's simple geometry allows straightforward use with common gauging procedures: insert for go/no-go checks, reference against calibrated master gauges or employ as a datum in manual measurement setups. Because the component is supplied ready for workshop use, it integrates quickly into existing inspection routines and reduces setup time. Complementary documentation and Metav's advisory services are available for users seeking to incorporate the pin into quality-control plans or to specify compatible fixtures. Choose the Metav IndustryLine precision gauge pin for controlled micro-dimension checks and contact Metav Werkzeuge in Emmerich for ordering and technical guidance: info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: M323.211 GTIN: 4061905054532 Brand: Metav IndustryLine Facts Diameter: 2.11 mm Tolerance / accuracy: ±0.001 mm Functional length: 50 mm Weight: 0.004 kg Special features Material: special steel Workshop version Supplied in transport case Category: gauge pins (Messstifte) FAQ What level of accuracy does this gauge pin provide? The M323.211 gauge pin from Metav IndustryLine is specified to ±0.001 mm, making it suitable for high-precision end-dimension checks. Is the pin suitable for use in a production workshop? Yes, the workshop version is made from special steel and supplied in a transport case for protection, designed for routine use on production benches. Which applications are best suited to this gauge pin? Compact bores, micro components and end-dimension verification are ideal applications; the 2.11 mm diameter and 50 mm length support checks in fine mechanical assemblies. Can the pin be used as a reference for fixture setup? Yes, the pin’s tight tolerance and stable length make it suitable as a reference datum for fixture calibration and comparative gauging tasks. What protective packaging is provided with the product? Delivery includes a transport case to protect the gauge pin during storage and handling. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
2.12mm Gauge Pin Precision ±0.001mm Length 50mm Workshop Version - Metav IndustryLine
The combination of ±0.001 mm measurement accuracy, a compact 2.12 mm diameter and a robust 50 mm length ensures reliable end‑measurement and repeatable checking results; order the gauge pin directly via Metav Werkzeuge or consult our specialists for integration advice. Gauge pin M323.212, single 2.12 mm, ±0.001 mm tolerance, 50 mm length (Metav IndustryLine) A gauge pin M323.212 designed for precision end‑measurement and go/no‑go checking in workshop and production quality control ±0.001 mm measurement accuracy 2.12 mm hardened special-steel pin 50 mm compact length for easy handling Cut inspection time with traceable precision The compact pin is engineered to deliver high repeatability through a manufacturing tolerance of ±0.001 mm, which reduces uncertainty in routine checks and accelerates go/no‑go decisions on the shop floor. A defined diameter of 2.12 mm and a consistent 50 mm length mean the part suits fixture reference points and microscopic fits without the need for frequent compromise adjustments. This measurable precision translates into fewer rechecks and higher throughput during batch acceptance and first‑article inspections. Built for daily workshop use and robust handling Constructed from special steel and finished for workshop execution, the pin resists wear under standard use while maintaining its measurement integrity. The compact 50 mm dimension improves ergonomics when handling small parts or when used inside confined fixtures, enabling quick placement and removal. The straightforward single‑pin format simplifies stocking and replacement; maintenance teams benefit from a durable, easily exchanged reference component that keeps inspection points operational. Easy integration into quality procedures and fixtures Designed as a practical measuring tool, the pin integrates smoothly into comparative checks, plug‑gauge arrays and fixture verification routines. Its clear numeric specification—diameter, length and tolerance—supports traceable documentation in quality reports and process control sheets. For shops adopting systematic quality measures, the pin offers an economical way to establish stable reference points without elaborate calibration requirements noted in the product data. For application advice or to confirm compatibility with specific jigs or measuring stations, Metav’s technical advisers are available to provide guidance. For purchasing or technical advice on the Metav IndustryLine gauge pin M323.212, contact Metav Werkzeuge directly by phone +49 2822 7131930 or email info@metav-werkzeuge.com to discuss suitability for production and delivery options Technical Data Article number: M323.212 GTIN: 4061905054549 SKU: M323.212 Brand: Metav IndustryLine Facts Diameter: 2.12 mm Length: 50 mm Tolerance: ±0.001 mm Weight: 0.004 kg Special features Material: Special steel Workshop execution Single gauge pin Category: Gauge pins FAQ What level of accuracy can be expected from the gauge pin? The gauge pin M323.212 is specified with a tolerance of ±0.001 mm, offering precision suitable for fine inspection tasks and reliable go/no‑go checks. Which materials is the pin made from? The M323.212 is manufactured from special steel and finished for workshop use to provide wear resistance and stable measurement performance. Is the pin supplied as a single item or in a set? This listing describes the gauge pin supplied individually as a single unit (SKU M323.212). Can the pin be used inside fixture assemblies and plug‑gauge checks? Yes. The defined 2.12 mm diameter and 50 mm length make the pin suitable as a reference element in fixtures, plug‑gauge arrangements and comparative inspection setups. Are calibration certificates included with the pin? The product data does not specify a calibration certificate; please contact Metav Werkzeuge for details on calibration services or certificate options. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
2.13mm Gauge Pin, Single, ±0.001mm Accuracy, 50mm Length, Workshop Version - Metav IndustryLine
Take advantage of workshop-grade 2.13 mm gauging with ±0.001 mm repeatability and robust special-steel construction for dependable end‑size checks; order directly via Metav Werkzeuge or consult the team for application advice. Pin gauge, single, 2.13 mm, ±0.001 mm, length 50 mm — Metav IndustryLine The pin gauge, single, 2.13 mm is a workshop-grade inspection pin designed for precise end‑size and fit verification in metalworking and precision assembly. Workshop-grade construction Diameter 2.13 mm ±0.001 mm Length 50 mm for compact inspections Special-steel construction Consistent metrology for repeatable end‑size checks The gauge pin delivers ±0.001 mm positional consistency, making it suitable where tight tolerances determine part acceptance. With a diameter of 2.13 mm and a solid 50 mm length, the component provides a measurable reference for plug fits, bore verification and comparative checks. Such a fine tolerance translates into measurable process reliability: production decisions based on this reference reduce rework and avoid downstream quality issues. The small form factor also supports use in confined inspection fixtures and bench routines without sacrificing stiffness or contact stability. Robust workshop design that stays dimensionally stable Built from special steel, this single inspection pin is specified for frequent workshop use where handling and contact wear must be controlled. The workshop‑grade construction reduces the risk of surface damage under repeated insertion and extraction cycles, preserving roundness and diameter integrity over time. At approximately 0.004 kg, the pin remains easy to position in fixtures and gauge blocks while offering sufficient mass for stable contact. The combination of material choice and compact geometry supports a long service life and predictable measurement behaviour. Practical benefits for production and inspection workflows Using a dedicated inspection pin streamlines routine verifications: quick go/no‑go testing, comparative gauging and fit assessments become straightforward and reproducible. The clear numerical specification and traceable SKU simplify inventory and quality documentation—supporting lean inspection routines and orderly tool management. Where accuracy matters, a defined reference such as this pin reduces subjective judgement and speeds up decision cycles on the shop floor, contributing directly to throughput and fewer rejects. Contact Metav Werkzeuge for tailored guidance on integrating the Metav IndustryLine pin gauge M323.213 into existing inspection routines; expert advice and procurement assistance are available from Emmerich. Technical data Article number: M323.213 GTIN: 4061905055232 Material: Special steel Label: Pin gauge, single, 2.13 mm, ±0.001 mm, length 50 mm Facts Diameter: 2.13 mm Tolerance: ±0.001 mm Length: 50 mm Weight: 0.004 kg ECLASS: 21170231 Special features Workshop execution Single test pin configuration SKU: M323.213 Story trigger: endmasse FAQ What tolerance can be expected from this inspection pin? The pin gauge is specified with a tolerance of ±0.001 mm; the Metav IndustryLine pin gauge M323.213 is intended for high‑precision end‑size checks where such repeatability is required. Which applications suit a 2.13 mm gauge pin? Small bore verification, plug‑fit checks, fixture setup and compact assembly inspection benefit from a 2.13 mm diameter pin, providing a clear reference for acceptance testing. Is the pin suitable for routine workshop use? Yes — the workshop‑grade construction and special‑steel material make the pin robust enough for frequent insertion and extraction in daily inspection routines. How is the pin identified for stock and quality records? The inspection pin is supplied as SKU M323.213 with GTIN 4061905055232 for unambiguous inventory and traceability. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
2.14mm Gauge Pin Length 50mm ±0.001mm Workshop Finish - Metav IndustryLine
Take advantage of ultra-fine dimensional control with a 2.14 mm diameter and ±0.001 mm positional accuracy, combined with a compact 50 mm length and workshop-grade construction for consistent fit checks. Order this gauge pin directly via Metav Werkzeuge or consult our advisors for tailored supply. M323.214 Gauge Pin — 2.14 mm, ±0.001 mm, 50 mm length (Metav IndustryLine) The M323.214 gauge pin offers micro‑range diameter verification for fine mechanical and end‑dimension checks in workshop environments ±0.001 mm tolerance Diameter 2.14 mm nominal Length 50 mm workshop design Made from special steel Precision that minimises rework and speeds inspection A nominal diameter of 2.14 mm combined with a tight ±0.001 mm tolerance (one micrometre) provides the dimensional certainty required for high‑accuracy go/no‑go checks and final inspection steps. The compact 50 mm length keeps the contact area stiff and reduces deflection during insertion, so repeatable results are achieved rapidly. This level of precision translates directly into lower scrap rates and fewer assembly mismatches, delivering a clear cost‑efficiency argument for production and quality teams. Designed for reliable fit checks and end‑dimension control Used as a reference pin in gauges, fixtures or as an end‑diameter master, this precision pin supports fast verification of bore sizes and assembly fits. The special steel construction gives consistent surface finish and contact behaviour, which is essential when working at micron‑scale tolerances. The workshop execution emphasises practical handling: small mass and compact geometry suit both hand operation and use within checking rigs, enabling efficient inspection cycles without complex setup. Practical durability for daily workshop use Although compact, the pin is manufactured to withstand routine handling in production environments. The workshop design ensures robustness where frequent insertion and withdrawal occur, while the small overall weight supports quick tool changes and minimal inertia in automated gauge heads. For quality engineers and toolroom technicians, the combination of fine nominal diameter and robust execution makes this item a dependable reference for dimension control in micro‑mechanical contexts. For micro‑precision gauging with 1 µm repeatability, contact Metav Werkzeuge GmbH in Emmerich to arrange supply or discuss application details — eMail: info@metav-werkzeuge.com • Phone: +49 2822 7131930 Technical Data SKU: M323.214 GTIN: 4061905055249 Brand: Metav IndustryLine Label: Prüfstift, einzeln, 2,14mm, +/- 0.001 mm Länge 50 mm Facts Diameter: 2.14 mm Length: 50 mm Tolerance: ±0.001 mm Weight: 0.004 kg Measurement range (max): 2.14 mm Special features Material: Special steel Workshop execution Application: End‑dimension and fit checks Story trigger: end dimensions FAQ What tolerance can be expected from this gauge pin? The M323.214 gauge pin is specified with a tolerance of ±0.001 mm, corresponding to 1 µm accuracy for high‑precision fit verification. Is the pin suitable for use in fixture gauges and plug checks? Yes, the precision pin is intended for fixture and plug checks where micro‑scale diameter control and repeatable insertion are required. What material is the pin made from and why does it matter? The pin is made from special steel, chosen to ensure consistent surface quality and contact behaviour during repeated measurements and fit tests. Can this pin be used in automated measuring stations? Its compact 50 mm length and low mass make the pin suitable for both manual and automated gauge heads designed for micro‑range diameter verification. How is the item identified for ordering or inventory? Order or reference this product by its SKU M323.214 or GTIN 4061905055249; both identifiers are listed above for procurement and inventory control. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
Fast, tactile checks where electronics are impractical
Gauges and test pins provide unequivocal go/no-go results for threads, bores, gaps and radii without relying on electronics. The range covers plug gauges and ring gauges for internal and external threads, feeler gauges and precision feeler strips for micro‑gap assessment, plus probe pins and measuring pins for tactile diameter and pitch checks.
How these tools work in the production environment
Mechanical gauges operate as direct reference standards: a plug gauge or ring gauge verifies conformity to thread profiles and mating ability, while limit gauges separate accept from reject in a single step. Test pins are used to tactilely measure small bore diameters, centre‑to‑centre distances and radii. Manufactured from hardened gauge steel or ceramic and often precision lapped, these instruments deliver immediate physical results that are ideal for incoming inspection, machine‑side checks and final control.
Measurable benefits that affect production performance
- Reduced scrap and rework through rapid, unambiguous pass/fail assessment.
- Increased repeatability thanks to very low measurement uncertainty and fine lapping.
- Lower downtime: quick checks at the machine save cycle time and reduce setup periods.
- Durable construction with high wear resistance from specialised, low‑distortion alloys.
- Versatile delivery formats: individual gauges, organised sets in wooden cases or metre‑length feeler rolls compliant with DIN 2269.
Why Metav is the practical choice for precision supplies
Metav combines decades of expertise with a broad warehouse and quality filtering from Emmerich. As a precision partner for industry, craft and trade, Metav supplies a comprehensive selection of gauges and test pins alongside complementary tools such as precision calipers and setting rings. With over 48,000 customers and a catalogue exceeding 250,000 items, Metav is positioned to supply reliably, reduce vendor complexity and support traceable quality control to national standards.
Summary
Gauges and test pins are indispensable for dependable, repeatable quality assurance where tactile, mechanical verification is preferred. Choose these plug gauges, ring gauges, feeler strips and probe pins when immediate, robust measurement decisions are required on the shop floor.
FAQ
What materials are gauges and test pins typically made from?
Gauges and test pins are usually manufactured from hardened gauge steel for durability and wear resistance; ceramic variants are available where thermal stability and minimal wear are critical.
How do thread gauges ensure mating capability?
Thread plug gauges and ring gauges check flank diameters and thread form against standards, providing a clear go/no‑go verdict that confirms pairability with mating parts.
Which tolerance class should I choose for probe pins and gauge sets?
Select tolerance classes aligned with your inspection requirements; for high‑precision tasks, sets produced to DIN 2269 or equivalent tolerance classes ensure micrometre‑level control and repeatability.
Can feeler gauges measure contact gaps in valve and engine work reliably?
Yes. Feeler gauges and precision feeler strips, supplied either as a fan or metre‑length rolls, allow accurate assessment of valve clearances and contact gaps down to micrometre increments.
How do limit gauges speed up in‑process inspection?
Limit gauges separate good from bad in a single, tactile operation, enabling rapid go/no‑go checks at the machine and reducing both inspection time and the likelihood of human interpretation errors.
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com