TPMT 16T304 T9215 Wendeplatten - Tungaloy
Take advantage of the combination of CVD-coated cemented carbide grade T9215, ISO conformity and a compact 0.4 mm nose radius for dependable medium-steel turning performance; order the inserts directly via Metav Werkzeuge or contact the consultants for application-specific recommendations. TPMT16T304-PS 16T304 T9215 — ISO turning insert (Tungaloy) TPMT16T304-PS T9215 is an ISO-compliant triangular indexable insert designed for external and internal turning, optimised for medium-steel applications CVD-coated cemented carbide T9215 Optimised for medium steel machining ISO triangular insert with cylindrical hole High wear resistance and fracture toughness Consistent cutting performance for medium-steel turning The triangular indexable insert delivers reliable tool life through a CVD-coated cemented carbide substrate identified as T9215. Chemical vapour deposition (CVD) applies a hard, wear-resistant layer that reduces flank and crater wear under continuous to slightly interrupted cutting. This composition combines wear resistance with fracture toughness, which supports stable, productive machining cycles and helps maintain component tolerances and surface quality during series production. ISO compatibility simplifies tooling choices and inventory As an ISO-standard insert, the part integrates into common turning systems; compatibility depends on form, relief angle, tolerance class, fastening, size and thickness. The system typically comprises the indexable insert, a matching external holder or boring bar, a supporting shim and clamp set, plus replacement fixing screws. Using standardised inserts streamlines stock management, reduces machine downtime and ensures predictable repeatability when assemblies are swapped between toolposts. Geometry and chip control tuned to practical turning tasks The insert features a 60° included angle and a 0.4 mm nose radius that balance edge strength and surface finish. A 11° relief angle supports general turning operations while the PS chipbreaker is suited to stable chip formation on medium steels. The plate thickness of 3.97 mm and a cylindrical hole with a one-sided countersink (40°–60°) enable secure clamping and consistent seat location, which is particularly important when repeatability and positional accuracy are required in production environments. Application advice and operational benefits Intended as a first-choice grade for medium-steel machining, this insert is suitable for both external and internal turning where continuous or lightly interrupted cuts occur. Selecting the correct chipbreaker and grade for the workpiece material and machining stability maximises tool life and productivity. The insert’s combination of geometry and T9215 grade aims to reduce unplanned tool changes, improve uptime and deliver consistent component surfaces without demanding specialised process parameters. For medium-steel turning tasks using Tungaloy’s T9215 grade, contact Metav Werkzeuge for tailored machining advice or to request availability at info@metav-werkzeuge.com or by telephone at +49 2822 7131930 Technical data Article number: 6772479 SKU: 6772479-Tungaloy Manufacturer SKU: TUN6772479 Manufacturer article number: 6772479 Model series: ISO-Drehwendeschneidplatten Label: TPMT16T304-PS T9215 Material: cemented carbide Core data Insert form: triangular ISO designation: 16T304 Chipbreaker: PS Nose radius: 0.4 mm Included angle: 60° Relief angle: 11° Plate thickness: 3.97 mm Plate size: 16 mm Hole: with hole Hole style: cylindrical hole + one-sided countersink (40°–60°) Special features Coating/grade: T9215 (CVD-coated cemented carbide) Typical application: turning (external and internal) Best for: medium-steel machining, continuous to light interrupted cuts Compatibility: determined by form, relief angle, tolerance class, fastening, size and thickness System components: insert, external holder or boring bar, shim/clamping set, replacement screws FAQ Is this insert suitable for internal boring as well as external turning? The TPMT16T304-PS T9215 insert by Tungaloy is designed for both external and internal turning tasks, provided the chosen holder or boring bar matches the insert’s form, size and clamping requirements. What advantages does the T9215 grade offer for steel machining? Tungaloy’s T9215 combines a CVD-coated cemented carbide structure with good wear resistance and fracture toughness, optimising tool life and process stability when machining medium steels. How does the 0.4 mm nose radius affect surface finish and strength? A 0.4 mm nose radius offers a compromise between improved surface finish and sufficient cutting-edge strength, making it suitable for many general turning operations without excessive tool load. What does the PS chipbreaker mean in practice? The PS chipbreaker is configured for controlled chip formation on medium steels, promoting stable chips under continuous to light interrupted cutting conditions and aiding swarf evacuation. How should compatibility with toolholders be checked? Compatibility depends on the insert’s shape, relief angle, fastening method, tolerance class, size and thickness; ensure the holder accepts 16T304 ISO triangular inserts and secures the cylindrical hole and countersink as specified. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
TPMT 16T304 T9215 Wendeplatten - Tungaloy
Take advantage of the combination of high wear resistance from the T9215 CVD coating, a compact 0.4 mm corner radius and secure ISO compatibility for reliable, productive turning operations. Order directly via Metav Werkzeuge or consult our technical team for application-specific recommendations. TPMT 16T304 T9215 — ISO turning indexable insert, CVD‑coated carbide, 0.4 mm corner radius — Tungaloy TPMT 16T304 T9215 is an ISO‑standard triangular indexable insert designed for external and internal turning in medium steel machining, combining robust wear resistance with stable chip control. TPMT indexable insert, ISO 16T304 CVD‑coated carbide grade T9215 Triangular shape with 0.4 mm corner radius 11° relief angle, cylindrical hole + countersink Productive performance for medium steel turning The insert’s CVD‑coated carbide grade T9215 provides a balanced combination of wear resistance and fracture toughness, making it particularly suitable for medium steel applications and continuous to lightly interrupted cuts. The integrated chipbreaker TSF promotes controlled chip formation and evacuation which supports higher feed rates and stable machining. These characteristics translate directly into improved throughput and predictable tool life, delivering a rational, performance‑driven advantage on the shop floor. Secure clamping and ISO compatibility for consistent results Manufactured to the ISO series specification, the insert is compatible with matching holders when form, relief angle, tolerance class, fastening method, size and thickness align. The part features a cylindrical hole with a single‑sided countersink (40°–60°) which assists accurate seating and repeatable clamping torque in standard toolholders and boring bars. This design focus reduces setup variability and contributes to more consistent component quality in batch production. Geometry engineered for precision and surface finish The triangular geometry with a 60° included angle and 0.4 mm corner radius offers a compromise between robustness and finishing capability: the small radius supports good surface integrity on external profiles while resisting edge chipping in general turning tasks. A 11° relief angle and a plate thickness of 3.97 mm ensure stable cutting edge support under radial and axial loads. These dimensional details are intended to produce repeatable surface finishes and dimensional control without sacrificing productivity. Practical application guidance and selection tips Intended for turning operations, the insert performs best when paired with an appropriate holder and cutting data matched to the workpiece and operation type. Select the TSF chipbreaker and T9215 grade for steel workpieces to maximise process reliability and tool life. For shorter runs or when encountering interrupted cuts, favour modest feeds and monitor edge condition; for continuous turning, advance cutting parameters gradually while keeping coolant and machine rigidity in mind. For further specification or optimisation of cutting parameters, Metav Werkzeuge’s consultants are available to advise on exact holder matching and parameter tuning. Contact Metav Werkzeuge today to specify these Tungaloy CVD‑coated inserts for improved productivity; technical consultants can be reached at info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: 6777786-Tungaloy Manufacturer article number: 6777786 Manufacturer SKU: TUN6777786 Designation: TPMT16T304-TSF T9215 Type: ISO turning indexable insert (TPMT) Manufacturer: Tungaloy Numerical data Corner radius: 0.4 mm Included angle: 60° Relief angle: 11° Plate thickness: 3.97 mm Plate size: 16 mm Design & special features Chipbreaker: TSF Coating: CVD‑coated carbide (T9215) Material: carbide Hole style: cylindrical hole + single‑sided countersink (40°–60°) Application: external and internal turning Model series: ISO turning indexable inserts Suitability: medium steel machining; continuous to lightly interrupted cuts FAQ Which materials are best machined with this insert? The T9215 CVD‑coated grade is optimised for medium steel machining; the TPMT16T304‑TSF insert delivers wear resistance and fracture toughness suited to continuous and light interrupted cuts in steel. How is holder compatibility ensured for these ISO inserts? Compatibility depends on the holder’s form, relief angle, tolerance class, fastening method, size and thickness; the TPMT format and the insert’s hole/countersink geometry enable secure seating in matching ISO toolholders. What benefit does the TSF chipbreaker provide? The chipbreaker TSF improves chip control and evacuation during turning, which supports higher feeds and more stable cutting, reducing the risk of rework and improving productivity with the T9215 grade insert. Can this insert be used for internal turning operations? Yes; the triangular TPMT geometry and standard hole arrangement allow use in appropriate boring bars and internal turning holders for both external and internal turning tasks. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
TPMT 16T304 T9225 Wendeplatten - Tungaloy
Take advantage of a robust combination of CVD-coated carbide and a well‑proven chipformer 24 for stable, productive turning in medium to heavy Stahl applications; order directly via Metav Werkzeuge or consult the team for process matching. TPMT 16T304 T9225 — ISO triangular turning insert for Stahl turning (Tungaloy) The TPMT16T304-24 T9225 is an ISO triangular insert designed for external and internal turning, offering a durable cutting grade for variable engagement and lightly interrupted cuts. ISO triangular insert 16T304 form CVD-coated carbide grade T9225 Robust for medium to heavy Stahl turning Higher productivity through a balanced cutting grade The combination of a CVD-coated surface and a carbide substrate in grade T9225 provides a balance between hardness and toughness that suits mixed and demanding turning tasks. This composition reduces flank wear under fluctuating cutting conditions while maintaining edge stability for longer tool life. The result is a measurable improvement in process reliability and less frequent insert changes, which supports continuous production and lowers intervention frequency. Precise geometry for consistent chip control A triangular insert with a 60° included angle and a corner radius 0.4 mm delivers predictable chip formation and repeatable geometry on turned parts. The integrated chipformer 24 moderates chip flow for the specified application, and the insert’s 11° relief angle ensures a stable cutting line with reduced rubbing on the flank. These geometry choices translate into a superior surface finish and consistent dimensional accuracy in component runs. Workshop compatibility and application flexibility The ISO designation 16T304 and the insert’s mounting features — cylindrical hole with one‑sided countersink (40°–60°) and a plate thickness 3.97 mm — make seat compatibility straightforward with matching ISO holders. Selection of the correct holder is determined by form, relief angle, tolerance class, clamping method, size and thickness. The insert is a practical choice where moderately heavy Stahl machining and occasional interrupted cuts require a tougher grade rather than an ultra‑hard coating, simplifying inventory while covering a wide range of turning tasks. Consult Metav Werkzeuge for application matching or request the Tungaloy TPMT16T304-24 T9225 specification sheet at info@metav-werkzeuge.com | +49 2822 7131930 Technical data Manufacturer article number: 6781201 SKU: 6781201-Tungaloy Manufacturer SKU: TUN6781201 Label: TPMT16T304-24 T9225 Model series: ISO-Drehwendeschneidplatten Material: carbide Numeric data Corner radius: 0.4 mm Included angle: 60° Relief angle: 11° Plate thickness: 3.97 mm Plate size: 16 Special features Coating: CVD-coated Grade: T9225 Chipformer: 24 Hole: with cylindrical hole + one-sided countersink (40°–60°) Plate form: triangular Application: Turning Typical use: medium to heavy Stahl machining; suitable for slightly interrupted cuts FAQ What material is the insert made from? The TPMT16T304-24 T9225 is produced from CVD-coated carbide (grade T9225), offering a balance of wear resistance and toughness for Stahl turning. Which applications suit this insert? This insert is intended for external and internal turning, particularly medium to heavy Stahl machining and situations with variable engagement or light interruptions. How does the chipformer influence performance? The chipformer 24 moderates chip flow to improve evacuation and surface quality under the specified cutting conditions for this insert. Is the insert compatible with standard ISO holders? Yes. The ISO designation 16T304 and the mounting features (cylindrical hole with countersink, 3.97 mm thickness) match ISO holders that accept this form and size; holder compatibility depends on form, relief angle, tolerance class, clamping and thickness. Can this insert handle interrupted cuts? Grade T9225 is formulated to provide additional toughness, making the insert suitable for lightly interrupted cuts and variable engagement scenarios. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
TPMT 16T304 T9225 Wendeplatten - Tungaloy
Take advantage of the combination of high toughness, reliable chip control and ISO compatibility for productive steel turning. Order the inserts directly via Metav Werkzeuge or consult their specialists for machining advice. TPMT 16T304 T9225 triangular indexable turning insert — CVD-coated carbide, chipbreaker PSF — Tungaloy TPMT 16T304 T9225 is a triangular ISO turning insert designed for external and internal turning of steel where medium to heavy cuts and intermittent engagement demand increased toughness CVD-coated carbide grade T9225 Robust universal grade for medium-heavy steel Chipbreaker PSF for stable chip control 60° triangle with 0.4 mm corner radius Consistent productivity through a balanced carbide grade The CVD-coated carbide composition of this insert, combined with the T9225 grade, provides a deliberate balance between wear resistance and fracture toughness. This balance is particularly beneficial in production environments where cutting conditions vary or where interrupted cuts are frequent. The result is fewer index changes and longer effective tool life, which lowers machine downtime and contributes to a more economical turning process. The robust specification supports higher material removal rates in steel while still maintaining surface quality. Design features that ensure secure clamping and accurate geometry The insert's triangular form with a 60° included angle and a corner radius of 0.4 mm gives both versatility and strength for a range of turning tasks. The relief angle of 11° and the plate thickness of 3.97 mm ensure correct seating and load distribution in ISO-compatible holders. The central cylindrical hole with a single-side countersink (40°–60°) supports standard clamping systems and simplifies replacement. Compatibility to specific holders is determined by form, clearance angle, tolerance class, clamping method, size and thickness; confirming these parameters avoids misfits and secures repeatable machining accuracy. Chip control and practical application guidance The integrated chipbreaker PSF is engineered to produce predictable, short chips when machining steels, improving evacuation and reducing the risk of entanglement on the workpiece or toolpost. For medium to heavy steel turning, select feeds and speeds according to job stability: a tougher grade like T9225 allows slightly more aggressive parameters than purely wear-focused grades, especially when cuts are intermittent. Where surface finish is critical, moderate feeds and appropriate nose radii will balance finish with productivity. The insert’s construction aids consistent chip formation across typical external and internal turning operations. Reliability, handling and selection advice for production shops As an ISO-standard turning insert from Tungaloy, TPMT 16T304 T9225 fits into established tooling systems and supports streamlined inventory management. The CVD-coated carbide layer improves resistance to abrasive wear while the substrate maintains fracture strength during variable engagement. When selecting inserts, match the chipbreaker, grade, and corner radius to the workpiece material and process stability; this reduces scrap risk and increases first-pass accuracy. For assistance with holder compatibility or process optimisation, Metav Werkzeuge provides technical advice to align insert choice with production goals. Contact Metav Werkzeuge for application-specific recommendations on Tungaloy turning inserts — reference SKU 6781224-Tungaloy and receive machining guidance or procurement support by email at info@metav-werkzeuge.com or by phone on +49 2822 7131930 Technical data Article number: 6781224-Tungaloy Manufacturer SKU: TUN6781224 Manufacturer article number: 6781224 Brand: Tungaloy Facts Corner radius: 0.4 mm Plate thickness: 3.97 mm Plate size: 16 mm Included angle: 60° Relief angle: 11° Special features CVD-coated carbide cutting material Grade T9225 – robust universal grade for medium to heavy steel machining Chipbreaker PSF ISO indexable turning insert series Triangular plate shape with central cylindrical hole and single-side countersink (40°–60°) Typical applications: external and internal turning FAQ What materials is this insert suited for? The TPMT 16T304 T9225 insert is designed primarily for steel machining; its T9225 grade provides toughness suited to medium and heavy steel turning operations. Which chip form can be expected with the PSF chipbreaker? The chipbreaker PSF produces controlled, short chips under typical steel turning conditions, improving evacuation and reducing the chance of chip-related interruptions. How does the CVD coating benefit tool life? The CVD-coated carbide layer increases abrasive wear resistance while the substrate maintains impact toughness, resulting in a longer effective life in variable cutting conditions. Is this insert compatible with ISO holders? This insert conforms to the ISO indexable insert system; compatibility depends on holder form, clearance angle, tolerance class, clamping and size — checking these parameters ensures correct fit. What is the manufacturer SKU for ordering and reference? The product is listed under SKU 6781224-Tungaloy and manufacturer SKU TUN6781224 for procurement and inventory purposes. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
TPMT 16T304 T9225 Wendeplatten - Tungaloy
Take advantage of the robust combination of CVD-coated carbide T9225 and precise PSS chip control for stable medium-to-heavy steel turning; order directly via Metav Werkzeuge or consult our specialists for optimal holder matching. TPMT 16T304 T9225 — Indexable turning insert (TPMT16T304-PSS) by Tungaloy, 60° triangle, 0.4 mm corner radius TPMT16T304-PSS T9225 is a CVD-coated carbide indexable insert designed for medium to heavy turning applications, offering reliable edge stability and adaptable chip control for variable engagement conditions. CVD-coated carbide grade T9225 Robust chip control with PSS breaker ISO 16T304 triangular geometry 0.4 mm corner radius for finishing Consistent performance for medium to heavy steel turning The TPMT16T304-PSS T9225 combines a CVD-coated carbide substrate with a universal wear-resistant grade to deliver consistent tool life in mixed production environments. The coating provides thermal resistance and improved flank wear behaviour, while the substrate maintains toughness during interrupted cuts. For operations where stability varies between finishes and heavier cuts, this insert reduces the frequency of tool changes and contributes to stable machining cycles, supporting predictable productivity. Improved chip control and surface quality Equipped with the PSS chipbreaker, the insert achieves controlled chip formation and evacuation, which leads to fewer tool interruptions and more consistent surface results. The 60° triangular geometry concentrates cutting forces and offers three effective cutting edges per indexable insert, optimising economy and setup time. By matching chipbreaker style and grade to the workpiece material and rigidity, shops benefit from reduced secondary operations and a smoother production flow. Straightforward integration with ISO holders for reliable clamping The ISO designation 16T304 signals broad compatibility with standard triangular turning holders when form, 11° relief angle, tolerance class, fastening method, size and thickness align. The insert’s cylindrical hole + single-side countersink (40°–60°) enables secure seating with common clamping systems, and the 3.97 mm thickness contributes to bending resistance under heavier feed conditions. This predictable fitment simplifies tool inventory and reduces the need for bespoke holder solutions. Application flexibility and workshop advantages Designed primarily for external and internal turning, the insert suits varied batch sizes and mixed-material workflows where a balance of wear resistance and toughness is required. The 0.4 mm corner radius is effective for light finishing and semi-finishing passes, offering a compromise between edge strength and surface finesse. Choosing the correct chipbreaker and stabilising the setup improves component consistency and cuts overall machining time, making the insert a practical choice for shops aiming to maintain throughput without sacrificing part quality. Discuss the Tungaloy T9225 grade with Metav Werkzeuge to optimise turning processes and holder compatibility; contact info@metav-werkzeuge.com or call +49 2822 7131930 to arrange technical advice and fast delivery Technical data Article number: 6781027-Tungaloy Manufacturer article number: 6781027 Manufacturer SKU: TUN6781027 Model series: ISO turning indexable inserts Material: Carbide Key specifications Insert designation: TPMT16T304-PSS Size: 16 Thickness: 3.97 mm Corner radius: 0.4 mm Relief angle: 11° Geometry angle: 60° Hole style: cylindrical hole + single-side countersink (40°–60°) Features and applications Coating/grade: CVD-coated carbide T9225 Chipbreaker: PSS Shape: triangular (TPMT) Typical use: external and internal turning System: ISO insert with matching holder, clamp and screw FAQ What materials is this insert best suited for? The TPMT16T304-PSS T9225 insert is intended as a robust universal grade for medium to heavy steel machining, offering a balance of wear resistance and toughness for variable cutting conditions. What are the key geometric features of the insert? The insert features a 60° triangular geometry, a 0.4 mm corner radius, 3.97 mm thickness and an 11° relief angle, providing three usable cutting edges and reliable edge strength for finishing passes. Which chipbreaker is fitted and what does it deliver? The PSS chipbreaker is integrated on this insert to ensure controlled chip formation and improved evacuation, which supports longer uninterrupted cuts and more consistent surface finishes. Is this insert compatible with standard holders? Yes. The ISO designation 16T304 indicates compatibility with ISO triangular turning holders, subject to matching form, tolerance class, fastening and size requirements; the insert sits via a cylindrical hole + single-side countersink (40°–60°) for secure clamping. How should the TPMT16T304-PSS T9225 be used in mixed-batch production? Select the PSS chipbreaker and the T9225 grade where interrupted cuts or variable engagement occur; the insert’s universality reduces inventory complexity while maintaining process stability across diverse components. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
TPMT 16T304 T9225 Wendeplatten - Tungaloy
TPMT 16T304 T9225 Drehen – TPMT16T304-PS von Tungaloy Die TPMT16T304-PS T9225 ist eine ISO-genormte Drehwendeschneidplatte für das Außen- und Innendrehen mit robuster Universalsorte für mittlere bis schwere Stahlbearbeitung Universalsorte T9225 für wechselnde Eingriffsbedingungen CVD-beschichtetes Hartmetall für hohe Standzeit Dreieckige Platte, Plattengröße 16 mm Mit Loch und zylindrischer Senkung 40°–60° Eckenradius 0,4 mm für vielseitige Konturen Effiziente Zerspanung und Wirtschaftlichkeit steigern Die TPMT16T304-PS kombiniert robuste Zähigkeit mit präziser Geometrie und richtet sich an Fertigungen mit wechselnden Schnittbedingungen. Durch die CVD-Beschichtung bleibt die Schneidkante länger stabil, was zu weniger Werkzeugwechseln und damit geringeren Stillstandzeiten führt. Die Formstabilität sorgt für konstante Bearbeitungsqualität bei Außen- und Innendrehen. Materialaufbau, Beschichtung und praktische Vorteile Das Hartmetall mit CVD-Beschichtung der Sorte T9225 bietet eine ausgewogene Mischung aus Verschleißfestigkeit und Zähigkeit, ideal bei leicht unterbrochenen Schnitten. Die Plattendicke von 3,97 mm und der Freiwinkel von 11° unterstützen stabile Spanbildung. Für Anwender bedeutet das zuverlässige Oberflächengüten und längere Werkzeugstandzeiten bei Stahlbearbeitung. Kompatibilität, Einbau und Anwendungshinweise Die ISO-Normierung garantiert Kompatibilität mit geeigneten Außenhaltern oder Bohrstangen, wobei Form, Freiwinkel, Toleranzklasse, Befestigung, Größe und Dicke zu beachten sind. Die einseitige Senkung des Lochs (40°–60°) erleichtert korrekte Fixierung. Anwender sollten Spanbrecher PS und Sorte T9225 passend zu Werkstoff und Maschinenstabilität wählen, um Prozesssicherheit zu maximieren. Zielgruppe, Nutzen und Prozesssicherheit Fertigungsbetriebe, die produktive Zerspanung und konstante Ergebnisse erwarten, profitieren von der stabilen Schneidkante und der breiten Werkstoffabdeckung. Die Platte eignet sich besonders für Betriebe mit variierenden Schnittbedingungen und bietet einen guten Kompromiss aus Standzeit und Zähigkeit. Damit werden Ausschussraten reduziert und Rüstzeiten effizient genutzt. Empfehlung: Die Tungaloy-TPMT16T304-PS mit T9225-Beschichtung über Metav Werkzeuge beziehen oder technische Beratung per E-Mail info@metav-werkzeuge.com bzw. Telefon +49 2822 7131930 anfragen Produktmerkmale Artikelnummer: 6781077 Hersteller: Tungaloy Serie: ISO-Drehwendeschneidplatten Bezeichnung: TPMT16T304-PS T9225 SKU: 6781077-Tungaloy Fakten Eckenradius: 0,4 mm Winkel: 60° Freiwinkel: 11° Plattendicke: 3,97 mm Plattengröße: 16 mm Besonderheiten Material: Hartmetall Beschichtung: T9225 (CVD-beschichtet) – robuste Universalsorte für mittlere bis schwere Stahlbearbeitung Plattenform: dreieckig Loch: mit Loch Lochstil: zylindrisches Loch + einseitige Senkung (40°–60°) Spanbrecher: PS – für stabile Spanformung bei wechselnden Schnitten Einsatz: Drehen Anwendung: Außen- und Innendrehen FAQ Welche Materialien lassen sich mit der TPMT16T304-PS bearbeiten? Die TPMT16T304-PS von Tungaloy mit Sorte T9225 eignet sich primär für Stahl und legierte Stähle; die Universalsorte ist für mittlere bis schwere Bearbeitung unter wechselnden Schnittbedingungen ausgelegt. Welchen Nutzen bringt die CVD-Beschichtung der T9225-Sorte? Die CVD-Beschichtung erhöht die Verschleißfestigkeit und sorgt für eine stabilere Schneidkante, wodurch die Standzeit der TPMT16T304-PS verlängert und die Produktivität gesteigert wird. Wie wähle ich den richtigen Spanbrecher? Der Spanbrecher PS der TPMT16T304-PS ist für leicht unterbrochene Schnitte und stabile Spanbildung empfohlen; die Wahl ist abhängig von Werkstoff, Schnittbedingungen und Maschinenstabilität. Ist die TPMT16T304-PS mit handelsüblichen ISO-Haltern kompatibel? Ja, die ISO-Genormung der TPMT16T304-PS gewährleistet Kompatibilität, wobei Form, Freiwinkel, Toleranzklasse, Befestigung, Größe und Dicke geprüft werden müssen. Hersteller: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenzeichen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers.
TPMT 16T304 T9225 Wendeplatten - Tungaloy
Take advantage of the combination of robust cutting performance, CVD-coated carbide reliability and ISO compatibility for consistent turning results; order directly via Metav Werkzeuge or consult our application specialists for tailored recommendations. TPMT 16T304 T9225 triangular turning insert — ISO turning insert by Tungaloy TPMT16T304-PM T9225 is a triangular, ISO‑standard turning insert developed for medium to heavy steel machining where intermittent cuts and varying engagement demand extra toughness. CVD-coated carbide T9225 grade Triangular ISO insert, 16 mm size 0.4 mm corner radius for versatile cuts 11° clearance, cylindrical hole with countersink Consistent metal removal under variable conditions The CVD‑coated, carbide construction provides a balance of hardness and toughness that supports productive machining in mixed shop environments. The T9225 grade is engineered as a robust universal option for medium to heavy steel machining, offering stable chip formation and improved resistance to micro‑chipping when cuts are interrupted. The insert’s chipbreaker PM is matched to the grade, which helps maintain consistent chip control during turning and reduces cycle‑time losses caused by poor evacuation. For process planners, this translates into predictable material removal rates and fewer unplanned tool changes. Precision geometry for reliable toolholder compatibility Shaped to ISO standards, the triangular form and the 16 mm size ensure compatibility with a wide range of external toolholders and boring bars when the seat form, thickness and fixing system match. The 0.4 mm corner radius supports a compromise between edge strength and surface finish, permitting moderate feed rates without sacrificing edge life. The insert’s 11° clearance angle reduces rubbing at the flank face and aids in maintaining dimensional accuracy, while the central cylindrical hole with a one‑sided countersink (40°–60°) assures secure clamping and consistent repeatability in indexable setups. Long tool life through engineered coating and material selection A CVD coating on the carbide substrate provides wear resistance on the rake face and thermal stability at elevated cutting temperatures typical of steel turning. The substrate material—sintered carbide—combines substrate toughness with a hard contact surface to withstand the abrasion and heat in continuous and interrupted cuts. This engineered pairing reduces flank wear and extends usable edge life, supporting longer tool cycles and fewer interventions for index changes. For manufacturers seeking steady output and lower tooling consumption, the result is improved process economy and less downtime. Contact Metav Werkzeuge for practical advice on integrating the Tungaloy turning insert into production workflows or request application‑specific cutting parameters and holder recommendations directly from Metav Werkzeuge Technical data Article number: 6781101 SKU: 6781101-Tungaloy Manufacturer SKU: TUN6781101 Manufacturer: Tungaloy Model series: ISO‑Drehwendeschneidplatten Core dimensions Size: 16 mm Thickness: 3.97 mm Corner radius: 0.4 mm Clearance angle: 11° Included angle: 60° Features and applications Shape: triangular Grade: T9225 Chipbreaker: PM Coating: CVD Material: carbide Application: Turning Hole: cylindrical hole + one‑sided countersink (40°–60°) Compatible with ISO toolholder systems FAQ What materials is this insert suitable for? The TPMT16T304‑PM T9225 is specified for medium to heavy steel machining, providing toughness for intermittent cuts and variability in engagement. How does the PM chipbreaker affect performance? The PM chipbreaker promotes controlled chip formation in turning operations, improving evacuation and reducing the risk of chip interference with the tool or workpiece. What clamping and holder features are required for correct mounting? Correct compatibility depends on the holder seat form, clearance angle, tolerance class, fixing method, insert size and thickness; the insert’s cylindrical hole with countersink ensures reliable clamping when the holder is ISO‑matched. Can this insert be used for finishing as well as roughing? The T9225 grade is a versatile universal option; while optimised for medium to heavy cuts, appropriate feeds and speeds can achieve satisfactory finishing results depending on component tolerances. What is the benefit of the 0.4 mm corner radius? A 0.4 mm corner radius increases edge strength for interrupted cuts while still allowing moderate feeds that keep surface finish within acceptable ranges for many turned components. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand‑new product from the manufacturer.
TPMT 16T304 T9225 Wendeplatten - Tungaloy
Take advantage of the CVD-coated carbide T9225 and the triangle 60° geometry to boost productivity in medium-to-heavy steel turning; the robust grade provides extended edge life under variable engagement. Order the inserts directly via Metav Werkzeuge or consult the technical team for application matching. TPMT 16T304 T9225 triangular turning insert, CVD-coated carbide (Tungaloy) TPMT16T304-TSF T9225 is a triangular ISO turning insert engineered for medium-to-heavy steel machining with ISO-compatible holders and a TSF chipbreaker. CVD-coated carbide T9225 Universal grade for medium-heavy steel Triangle insert with 60° cutting angle 0.4 mm corner radius for versatile cuts Faster cycles through a robust, universal grade The insert uses a CVD-coated carbide substrate in the T9225 grade, chosen for its balance of toughness and wear resistance in interrupted or variable cuts. This combination supports higher cutting parameters and longer tool life under fluctuating engagement, translating into fewer tool changes and improved machine uptime. The result is a measurable uplift in productivity for workshops running mixed batch sizes, where consistency and predictable edge performance are essential. Clear guidance on holder compatibility and mounting Compatibility depends on geometry: form, relief angle, tolerance class, fastening, size and thickness determine correct pairing with holders. The triangle shape and with hole design — a cylindrical hole with a one-sided countersink at 40°–60° — ensure secure clamping when used with appropriate ISO external holders or boring bars. Specifying holders that match the 11° relief and 3.97 mm plate thickness prevents misalignment and secures stable cutting conditions, reducing vibration and improving surface finish. Predictable edge life in demanding steel turning For medium-to-heavy steel operations, the TSF chipbreaker combined with the 0.4 mm corner radius provides a compromise between chip control and edge strength. This geometry reduces tendency to notch and maintains positive cutting action on variable shoulders or interrupted cuts. When the TPMT16T304-TSF T9225 insert is used with stable setups, the outcome is consistent dimensional accuracy and fewer reworks, supporting cost-efficiency in serial production and repair tasks. Simple specification for process planning and inventory Process planners benefit from the ISO designation and measurable parameters: 16 mm size, 3.97 mm thickness, 60° cutting angle and defined hole style. These clear specifications simplify tool list creation, stock keeping and rapid replacement. Selecting the correct grade and chipbreaker for the material and operation avoids over‑engineering and supports an efficient, repeatable machining routine with lower overall tooling consumption. For application advice, grade selection or to order Tungaloy T9225 inserts, contact Metav Werkzeuge—technical consultants are available at info@metav-werkzeuge.com or +49 2822 7131930 to ensure the right insert and holder pairing for the operation. Technical Data Article number: 6781468 Manufacturer article number: 6781468 Manufacturer SKU: TUN6781468 SKU: 6781468-Tungaloy ISO designation: TPMT16T304-TSF Facts Size: 16 mm Thickness: 3.97 mm Corner radius: 0.4 mm Relief angle: 11° Cutting angle: 60° Countersink angle: 40°–60° Special features Shape: triangular Grade/coating: CVD-coated carbide T9225 Chipbreaker: TSF Hole: cylindrical hole + single countersink Application: turning Series: ISO turning inserts FAQ What machining tasks suit this insert best? The insert is intended for external and internal turning operations, especially mid- to heavy-duty steel machining where variable engagement or slight interruptions require a tougher grade such as T9225. Is the insert compatible with standard ISO holders? Compatibility is determined by form, relief angle, tolerance and thickness; the TPMT geometry and the specified 11° relief mean the insert fits ISO-compliant external holders designed for triangular inserts, given matching clamping and support. How does the TSF chipbreaker affect performance? The TSF chipbreaker promotes controlled chip formation in steel turning, improving evacuation and reducing built-up edge risk, which enhances surface finish and tool life in the specified grade. What material is the insert made from? The cutting body is made of carbide and finished with a CVD coating, delivering balanced wear resistance and toughness suited to the grade T9225. Which dimensions should be specified when ordering replacements? Key dimensions are ISO designation TPMT16T304-TSF, size 16 mm, thickness 3.97 mm, corner radius 0.4 mm and the hole/countersink style; quoting the article number 6781468 or SKU 6781468-Tungaloy ensures exact replacement. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
TPMT 16T308 AH6225 Wendeplatten - Tungaloy
Benefit from a combination of a universal PVD-coated carbide grade AH6225, ISO TPMT geometry and a 0.8 mm corner radius that together deliver a stable, sharp cutting edge for medium turning of rostfreie Stähle; order the TPMT16T308-PSS AH6225 directly via Metav Werkzeuge or consult our specialists for application advice. TPMT16T308-PSS AH6225 TPMT 16T308 AH6225 ISO turning insert for turning — Tungaloy, PVD-coated carbide, 0.8 mm The TPMT16T308-PSS AH6225 is an ISO triangular turning insert engineered for external and internal turning operations, offering a sharp yet robust edge for medium machining and changing conditions. ISO triangular form TPMT for secure clamping PVD-coated AH6225 tuned for rostfreie Stähle 0.8 mm corner radius for reliable edge strength Cylindrical hole with single-sided countersink for stable fixing Consistent cutting performance in medium turning The triangular insert geometry provides predictable cutting behaviour, while the PVD-coated carbide composition combines hardness with toughness for repeatable results. The specified grade, AH6225, is optimised for rostfreie Stähle and designed to maintain a sharp, stable cutting edge during medium-duty operations and when conditions vary. This leads to fewer insert changes, reduced machine downtime and a more consistent surface finish on workpieces where process stability matters. Precision geometry and secure clamping for reliable results With the ISO TPMT form and a cylindrical hole plus single-sided countersink (40°–60°), the insert offers secure seating and accurate location in compatible holders. The 11° relief angle and a corner radius of 0.8 mm balance edge strength and cutting clearance, enabling controlled chip formation with the PSS chipbreaker and contributing to predictable tool life. These geometric choices simplify setup decisions: select the holder matching form, size and thickness and benefit from stable cutting forces and repeatable positioning. Practical handling and application benefits for workshops The insert’s 16 mm size and 3.97 mm thickness make it suitable for a wide range of standard external and internal turning holders that accept ISO TPMT plates. The PVD coating improves wear resistance under variable conditions, permitting higher productivity while maintaining surface quality. For production environments seeking steady throughput, the combination of ISO conformity, reliable chip control and a universal carbide grade supports efficient tool management and quicker changeovers. For tailored advice on fitting the TPMT16T308-PSS AH6225 into existing toolholders or for recommendations on cutting data for rostfreie Stähle, contact Metav Werkzeuge — technical consultants are available to help match inserts to applications and machine capabilities. Technical data Article number: 6829897 SKU: 6829897-Tungaloy Manufacturer SKU: TUN6829897 Model series: ISO-Drehwendeschneidplatten Material: Hartmetall Coating/grade: AH6225 (PVD-beschichtet) Facts Size: 16 mm Thickness: 3.97 mm Corner radius: 0.8 mm Relief angle: 11° Included angle: 60° Special features ISO designation: TPMT16T308-PSS Type: TPMT triangular insert Chipbreaker: PSS Mounting: with hole; cylindrical hole + single-sided countersink (40°–60°) Typical application: Drehen (external and internal turning) FAQ What materials is this insert suitable for? The AH6225 grade and PVD coating make the insert particularly suitable for rostfreie Stähle and general turning tasks where a balance of edge sharpness and stability is required. Which holders are compatible with this insert? Compatibility depends on insert form, relief angle, tolerance class, fastening method, size and thickness; the TPMT geometry and the cylindrical hole with countersink are matched to standard ISO TPMT holders. How does the PSS chipbreaker affect machining? The PSS chipbreaker promotes controlled chip formation for medium cutting depths, improving chip evacuation and contributing to consistent surface quality. What does the 0.8 mm corner radius mean for edge life and finish? A 0.8 mm corner radius enhances edge strength compared with smaller radii while still allowing good surface finish; it provides a compromise between robustness and fine finish on rostfreie Stähle. Is this insert suitable for both external and internal turning? Yes, the insert is specified for both external and internal turning when used with appropriate holders and tool setups. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
TPMT 16T308 AH6225 Wendeplatten - Tungaloy
Take advantage of a PVD-coated carbide grade designed for reliable machining of stainless steels, combined with a sharp, stable cutting edge and ISO compatibility for straightforward toolholder selection; order directly via Metav Werkzeuge or consult our specialists for application advice. TPMT 16T308 AH6225 triangular ISO turning insert, PVD-coated carbide for turning (Tungaloy) The TPMT16T308-PM AH6225 is an ISO-format triangular indexable insert engineered for external and internal turning, offering a medium-duty cutting solution optimised for variable machining conditions. ISO triangular insert TPMT 16T308 AH6225 PVD-coated carbide for stainless steels Sharp yet stable cutting edge, medium duty Cylindrical hole with 40°–60° countersink Reliable machining performance for turning operations The PVD-coated, cemented carbide grade AH6225 delivers a consistent balance between wear resistance and edge toughness, which is particularly valuable when working with stainless steels. The coating reduces flank and crater wear, extending tool life under fluctuating cutting conditions. The insert's geometry yields a controlled cutting action that helps maintain component dimensional stability, so operators can expect repeatable results across batches and reduced frequency of insert changes. Secure mounting and ISO compliance for fast tool changes Compatibility with ISO-certified holders is a core design consideration; the triangular plate features a cylindrical centre hole with a single-side countersink (40°–60°) for secure clamping and accurate seating. This arrangement simplifies assembly on standard external holders or boring bars and reduces set-up time. The standardised form and tolerance class ensure interchangeability within ISO tool systems, supporting efficient workshop logistics and minimising downtimes caused by bespoke clamping solutions. Balanced chip control and edge life for mixed conditions The PM chipbreaker profile provides consistent chip control during both external and internal turning, reducing the likelihood of entangling or long stringy chips in interrupted cuts. The combination of a 0.8 mm corner radius and the insert’s medium-duty geometry gives a compromise between edge strength and surface finish: the edge resists chipping while still delivering acceptable surface quality on most turned parts. For workshop managers, this means fewer rejects and more predictable insert consumption. Versatility across stainless-steel turning tasks Designed as a universal grade for stainless steels, the insert supports a wide range of turning strategies—from light finishing to moderate roughing—by choosing appropriate feeds and speeds for the material and machine stability. The 3.97 mm plate thickness and the 60° included angle assist in distributing cutting forces, which improves stability on less rigid set-ups. When working with variable workpiece geometries or interrupted cuts, this insert provides a practical compromise between performance and robustness. Contact Metav Werkzeuge for tailored machining recommendations for the Tungaloy TPMT16T308-PM AH6225 insert or to request availability and delivery options from Metav Werkzeuge. Technical Data Article number: 6831835 SKU: 6831835-Tungaloy Manufacturer SKU: TUN6831835 Designation: TPMT16T308-PM AH6225 Core data Corner radius: 0.8 mm Plate size: 16 mm Plate thickness: 3.97 mm Included angle: 60° Clearance angle: 11° Special features PVD-coated carbide grade AH6225 PM chipbreaker form Triangular plate with hole and single-side countersink (40°–60°) ISO-series turning insert, compatible with ISO holders Intended application: turning; optimised for stainless steels FAQ What applications is this insert designed for? The TPMT16T308-PM AH6225 insert is designed primarily for external and internal turning operations and is optimised for machining stainless steels under medium-duty conditions. Is the insert compatible with standard ISO toolholders? Yes. The insert follows ISO geometry and seating tolerances; the cylindrical centre hole with single-side countersink ensures secure clamping in ISO-compatible holders. What does the PM chipbreaker provide? The PM chipbreaker on this Tungaloy turning insert improves chip control for a range of cutting conditions, helping to avoid long, stringy chips and facilitating safe, continuous turning. How does the 0.8 mm corner radius affect performance? A 0.8 mm corner radius provides a compromise between a robust cutting edge and surface finish, offering improved resistance to chipping while still allowing acceptable part quality on most turning tasks. Which material types is the insert best suited to? The PVD-coated carbide grade AH6225 is formulated as a universal choice for stainless steels, providing wear resistance and edge stability across variable stainless-material compositions. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
TPMT 16T308 AH6225 Wendeplatten - Tungaloy
TPMT 16T308 AH6225 TPMT Drehwendeschneidplatten für Drehen von Tungaloy Die TPMT 16T308 AH6225 ist eine ISO-genormte Drehwendeschneidplatte, entwickelt für das Außen- und Innendrehen an rostfreien Stählen mit stabiler Schneidkante und mittlerer Bearbeitungsleistung. Universelle Sorte für rostfreie Stähle PVD-beschichtetes Hartmetall für lange Standzeit Dreieckige Platte mit 16 mm Kantenlänge Eckenradius 0,8 mm für feine Konturen Mit Loch und zylindrischer Senkung für robuste Befestigung Hohe Prozesssicherheit und wirtschaftliche Zerspanung Die TPMT16T308-PS AH6225 überzeugt durch PVD-beschichtetes Hartmetall, das Verschleiß reduziert und die Standzeit erhöht. Bei der Bearbeitung von rostfreien Stählen führt die Beschichtung zu weniger Anhaften und stabiler Schneidkante, was Werkzeugwechselzeiten und Stillstand reduziert. Kunden profitieren direkt von geringeren Produktionskosten durch längere Einsatzintervalle und konstantere Schnittbilder. Präzise Geometrie für wiederholgenaue Ergebnisse Die dreieckige Plattenform mit Eckenradius 0,8 mm und einem Freiwinkel von 11° sorgt für reproduzierbare Schnittergebnisse bei mittleren Schnittbedingungen. Diese Geometrie unterstützt eine stabile Spanbildung und ermöglicht präzise Oberflächen, besonders bei wechselnden Bearbeitungsrandbedingungen. Für Anwender bedeutet das weniger Nacharbeit und zuverlässigere Bauteilqualität. Einfache Integration in bestehende Haltersysteme Dank ISO-Genormtheit ist die Platte für gängige Außenhalter und Bohrstangen kompatibel; entscheidend sind dabei Form, Freiwinkel, Toleranzklasse und Befestigung. Die Ausführung mit Loch und die zylindrische Lochform mit einseitiger Senkung (40°–60°) erleichtern die Montage und verbessern die Wiederholgenauigkeit der Positionierung. Dadurch wird die Rüstzeit verkürzt und die Prozessstabilität erhöht. Zielgruppe und typische Einsatzfälle Die Wendeschneidplatte richtet sich an Fertigungsbetriebe und Lohnbearbeiter, die rostfreie Stähle mittlerer Härte produktiv drehen wollen. Empfohlen ist die Sorte für Anwendungen, bei denen eine scharfe, aber belastbare Schneidkante gefragt ist, etwa im Serien- und Schichtbetrieb. Technische Entscheider schätzen die Kombination aus Zuverlässigkeit und Verfügbarkeit im industriellen Alltag. Empfehlung: Wählen Sie die Originalplatten von Tungaloy für maximale Prozesssicherheit und Abstimmung auf Ihre Haltersysteme; bei Fragen zur Auswahl oder für technische Details erreichen Sie uns per eMail an info@metav-werkzeuge.com oder telefonisch unter +49 2822 7131930. Produktmerkmale Artikelnummer: 6831311 Marke: Tungaloy Serie: ISO-Drehwendeschneidplatten Bezeichnung: TPMT16T308-PS AH6225 Hersteller SKU: TUN6831311 Fakten Eckenradius: 0,8 mm Winkel: 60° Freiwinkel: 11° Plattendicke: 3,97 mm Plattengröße: 16 mm Besonderheiten Material: Hartmetall Schneidstofftyp: PVD-beschichtetes Hartmetall Sorte: AH6225 Spanbrecher: PS — Spanformer für stabile Spanbildung Loch: mit Loch — zylindrisches Loch + einseitige Senkung (40°–60°) Form: dreieckig Einsatz: Drehen Norm: ISO-genormt — Austauschbarkeit und Kompatibilität zu genormten Haltern FAQ Für welche Werkstoffe ist die Platte geeignet? Die AH6225-Sorte ist ausgelegt für die Bearbeitung von rostfreien Stählen; die TPMT16T308-PS AH6225 bietet eine scharfe und zugleich stabile Schneidkante, geeignet für mittlere Schnittbedingungen. Ist die Platte für Innen- und Außen-Drehen verwendbar? Ja, die ISO-Geometrie und die dreieckige Form ermöglichen sowohl Außen- als auch Innendreh-Anwendungen, solange Halterform und Freiwinkel kompatibel sind. Wie beeinflusst die PVD-Beschichtung die Standzeit? Die PVD-Beschichtung reduziert Reibung und Anbackungen, was bei rostfreien Stählen zu längeren Standzeiten und gleichmäßigeren Oberflächen führt. Wie wählt man den passenden Halter aus? Die Kompatibilität hängt von Form, Freiwinkel, Toleranzklasse, Befestigung, Größe und Dicke ab; bei Unsicherheit hilft die Angabe der Bezeichnung TPMT16T308-PS AH6225 und der Artikelnummer 6831311 zur schnellen Zuordnung. Welchen Vorteil bringt der Spanbrecher PS? Der Spanbrecher PS sorgt für kontrollierte Spanformung und reduziert die Gefahr von Spanverwicklungen, besonders bei instabilen Schnittbedingungen. Hersteller: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenzeichen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers.
TPMT 16T308 AH6235 Wendeplatten - Tungaloy
Benefit from the combination of the PVD-coated AH6235 grade and a 0.8 mm corner radius for secure performance in stainless-steel turning and interrupted cuts; order the insert directly via Metav Werkzeuge or contact our consultants for selection support. TPMT16T308-PS AH6235 — TPMT 16T308 ISO turning insert for turning applications by Tungaloy The TPMT16T308-PS AH6235 is an ISO-standard triangular turning insert designed for external and internal turning, optimised for stainless-steel machining and interrupted cuts. PVD-coated carbide grade AH6235 Suitable for stainless-steel machining 0.8 mm corner radius for robustness ISO triangular format, 60° included angle Secure chip control when machining stainless steel The PVD-coated AH6235 grade offers a balance of toughness and wear resistance that is particularly beneficial for stainless-steel applications and conditions with intermittent cutting. The combination of the PS chipbreaker and a PVD coating reduces the risk of built-up edge and chipping during interruptions, which translates into fewer rejects and more predictable production runs. This insert is thus suited to turning tasks where material stickiness and thermal sensitivity demand a tougher grade rather than a hard, brittle coating. Geometry that improves surface finish and repeatability A 60° triangular shape with a 0.8 mm corner radius delivers a reliable compromise between edge strength and the ability to produce defined contour radii. The 11° clearance angle and ISO conformity ensure compatibility with widely used holders; the standardised geometry makes tool changes and programme validation straightforward. For operators less familiar with insert geometry: a larger corner radius increases edge support and helps maintain dimensional stability under vibration, while the triangular format supplies multiple indexable cutting edges to reduce tooling costs. Process efficiency through longer edge life and stable cutting Selecting the right grade and chipformer reduces downtime for insert changes. The PVD coating improves resistance to abrasive wear and adhesion, extending effective cutting life in demanding cycles and helping to maintain surface quality over longer runs. Combined with the PS chipbreaker and the insert’s mechanical design, the result is fewer tool interventions and a more consistent output—advantages that contribute directly to lower production costs and improved throughput in turning operations. For technical advice on using Tungaloy PVD-coated inserts in stainless-steel turning and to arrange supply through Metav Werkzeuge, contact our consultants at Metav Werkzeuge for prompt, application-focused support. Technical Data Article number: 6890208 Manufacturer SKU: TUN6890208 SKU: 6890208-Tungaloy Facts Radius: 0.8 mm Thickness: 3.97 mm Insert size: 16 mm Clearance angle: 11° Included angle: 60° Hole: with hole Hole style: cylindrical hole + one-sided countersink (40°–60°) Special features Material: carbide Coating: PVD Grade: AH6235 Chipbreaker: PS Shape: triangular Application: turning (external and internal), suitable for interrupted cuts ISO-series: ISO turning inserts, compatible with ISO holders FAQ Which materials is this insert best suited for? The TPMT16T308-PS AH6235 is optimised for stainless-steel machining; the AH6235 grade provides toughness for interrupted cuts and applications with increased risk of chipping. Can the insert be used for internal turning as well as external turning? Yes, the ISO triangular format and geometry of the TPMT16T308-PS AH6235 make it suitable for both external and internal turning operations when paired with the appropriate holder. What does the 0.8 mm corner radius mean for machining results? A 0.8 mm corner radius increases edge strength and improves dimensional stability under load, helping to achieve consistent surface quality and longer tool life compared with very small radii. How does the PS chipbreaker influence chip formation? The PS chipbreaker is designed to produce manageable chips in stainless-steel turning; combined with the PVD-coated AH6235 grade, it reduces tendency to form long, tangled chips and lowers the risk of edge failure. Which SKU should be referenced when ordering or enquiring? Use SKU TUN6890208 or article number 6890208 when ordering the TPMT16T308-PS AH6235 insert from Metav Werkzeuge. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
TPMT 16T308 AH6235 Wendeplatten - Tungaloy
Combine PVD-coated AH6235 wear resistance with a stable 60° triangular geometry and a precise 0.8 mm nose radius for consistent turning of stainless steel and interrupted cuts — order the inserts directly via Metav Werkzeuge or contact our consultants for application support. TPMT 16T308 AH6235 — ISO triangular turning insert for turning (Tungaloy) The TPMT16T308-PM AH6235 is an ISO-indexable triangular insert engineered for external and internal turning, designed specifically for stainless steel, interrupted cuts and applications with increased breakage risk. PVD-coated carbide grade AH6235 Designed for stainless steel machining Triangle 60° form, 0.8 mm nose radius Cylindrical hole with one-sided countersink Proven performance for stainless steel and difficult cuts The combination of a PVD-coated surface and the AH6235 carbide grade provides a tougher cutting edge optimised for stainless steel and interrupted cutting conditions. The PVD coating enhances wear resistance and reduces built-up edge, while the substrate grade is balanced for toughness rather than maximum hardness. This balance decreases the likelihood of edge chipping during interrupted cuts and prolongs effective tool life, delivering measurable improvements in process reliability and component quality for serial and job-shop turning operations. Geometry and clamping that ensure repeatable results The insert’s 60° triangle shape and 0.8 mm nose radius give a predictable engagement geometry for a wide range of turning passes. With a plate thickness of 3.97 mm and a 11° clearance angle, the insert matches common ISO holder dimensions; compatibility is governed by form, clearance angle, tolerance class, fastening, size and thickness. The insert features a cylindrical hole with one-sided countersink (40°–60°) for secure clamping and consistent seating in compatible holders, reducing vibration and improving surface finish stability. Chip control and surface finish with the PM chipbreaker The PM chipbreaker is tailored to general finishing and medium-depth cuts, promoting controlled chip formation in stainless steel and similar alloys. Controlled chips lower the risk of entanglement, permit higher feed rates in many cases and simplify automated chip handling. The engineering of the chipformer reduces cutting irregularities, which contributes directly to improved surface roughness and reduced downstream finishing time — a clear operational advantage for production lines aiming for consistent component tolerances. System thinking: how the insert integrates into the tool setup Delivered as an ISO-indexable cutting plate, the insert forms part of a modular system that includes a matching external holder or boring bar, a shim/clamp set and replacement screws as required. The carbide substrate and PVD finish are suited to a broad range of turning tasks when combined with the correct holder geometry and clamping torque. For ordering and inventory control, the item is listed under manufacturer article number 6890215 and manufacturer SKU TUN6890215, enabling straightforward procurement and traceability in procurement systems. Request application advice from Metav Werkzeuge for optimised use of Tungaloy AH6235 inserts — contact info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: 6890215 Manufacturer SKU: TUN6890215 SKU: 6890215-Tungaloy Manufacturer: Tungaloy Core data ISO designation: 16T308 Insert form: Triangle, 60° Size: 16 Thickness: 3.97 mm Nose radius: 0.8 mm Relief angle: 11° Special features ISO-indexable triangular turning insert Grade AH6235, PVD coating PM chipbreaker With cylindrical hole and one-sided countersink (40°–60°) Suitable for turning (Drehen) Suited to stainless steel and interrupted cuts Carbide material ISO series: ISO-Drehwendeschneidplatten FAQ What materials is this insert best suited for? The insert is optimised for stainless steel and similar alloys; the AH6235 grade and PVD finish provide toughness and wear resistance suitable for interrupted cuts and challenging stainless steel applications. How does the PM chipbreaker affect machining performance? The PM chipbreaker promotes controlled chip formation for finishing and medium cutting depths, improving surface finish and reducing the likelihood of chip-related interruptions when using the TPMT16T308-PM AH6235 insert. Which holder characteristics are required for proper fit? Compatibility depends on the insert form, 11° clearance angle, tolerance class, fastening method, size and thickness — ensure the holder matches the ISO triangular 60° geometry and clamping provisions. What information is useful when reordering this insert? Use the manufacturer article number 6890215 or manufacturer SKU TUN6890215 to ensure the correct AH6235 PVD-coated carbide grade and PM chipbreaker variant are supplied. Can this insert be used for both external and internal turning? Yes, the indexable triangular design is suitable for both external and internal turning when paired with an appropriate external holder or boring bar and correct clamping components. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
TPMT 16T308 AH725 Wendeplatten - Tungaloy
Benefit from the combination of the PVD-coated AH725 grade and a 0.8 mm corner radius for stable, repeatable turning results in mixed steel and stainless-steel applications; order directly via Metav Werkzeuge or request advice from our consultants for process optimisation. TPMT 16T308 AH725 — ISO turning insert, triangular 60°, Tungaloy The TPMT 16T308 AH725 is an ISO-standard triangular turning insert designed for external and internal turning, combining a PVD-coated carbide substrate with a PM chipbreaker for dependable chip control in varied steels. PVD-coated carbide AH725 for steel and stainless steel 60° triangular insert with 0.8 mm corner radius PM chipbreaker for secure chip control Compatible with ISO holders with central hole Reliable chip control for consistent cycle times The combination of the PM chipbreaker and the AH725 cutting grade delivers predictable chip formation and evacuation, which directly supports shorter cycle times and fewer interruptions. The PVD coating provides a hard, wear-resistant surface that reduces built-up edge on stainless steels while maintaining sharp cutting performance in common alloyed steels. In practice, this means fewer insert changes and a more consistent surface finish across batches, helping to sustain throughput without sacrificing process security. Simple integration into ISO tooling systems The insert follows ISO geometry and is specified with a 60° included angle, 11° clearance, 16 mm size and 3.97 mm thickness, ensuring compatibility with established turning holders when form, clearance angle, tolerance class, fixing method, size and thickness are matched. The central cylindrical hole with a single-sided countersink (40°–60°) supports secure clamping and repeatable seating. These standardised dimensions make tool-pool management easier and reduce set-up time when swapping inserts between machines. Durable edge and broad material coverage for process security Manufactured from carbide and finished with PVD treatment, the grade is described as a universal, fracture-resistant choice for both steel and stainless steel, especially where material mixes or smaller tooling demands high reliability. The 0.8 mm corner radius balances edge strength and finish capability, enabling light to moderate finishing passes while resisting chipping in interrupted cuts. For production environments that prioritise continuity, this specification supports longer effective tool life and stable part quality. Contact Metav Werkzeuge today for tailored recommendations on the Tungaloy TPMT 16T308 AH725 PVD-coated carbide turning insert and secure a reliable supply; email info@metav-werkzeuge.com or call +49 2822 7131930 for expert assistance. Technical data Article number: 6856731 Manufacturer: Tungaloy Manufacturer SKU: TUN6856731 SKU: 6856731-Tungaloy Model series: ISO-Drehwendeschneidplatten Item designation: TPMT16T308-PM AH725 Facts Size: 16 mm Thickness: 3.97 mm Corner radius: 0.8 mm Clearance (free) angle: 11° Included angle: 60° Manufacturer article number: 6856731 Special features Material: carbide Coating: PVD-coated Grade: AH725 Chipbreaker: PM Plate shape: triangular Hole style: cylindrical hole + single-sided countersink (40°–60°) Application: turning FAQ What materials is this insert suited for? The TPMT 16T308 AH725 is specified for steel and stainless steel work, with the AH725 PVD-coated carbide grade offering universal, fracture-resistant performance across those materials. How does the PM chipbreaker affect machining? The PM chipbreaker on this insert supports controlled chip formation and evacuation; the result is improved process stability and reduced risk of chip-related interruptions when turning steels. Which holder compatibility factors must be checked? Compatibility is determined by insert form, clearance angle, tolerance class, fixing method, size and thickness; the TPMT 16T308 AH725 uses a central cylindrical hole with a single-sided countersink for secure clamping. Is the corner radius suitable for finishing operations? With a 0.8 mm corner radius, the insert provides a balance between edge strength and surface finish capability, suitable for light finishing passes and stable performance in interrupted cuts. Can the AH725 grade be used for mixed-material production runs? Yes, the AH725 grade is designed as a universal, breakage-resistant option for varied steels and stainless steels, making it practical for production environments with changing materials. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
TPMT 16T308 AH725 Wendeplatten - Tungaloy
Take advantage of the combination of universal PVD-coated carbide grade AH725, robust chip control with the PS chipbreaker, and precision geometry for stable, repeatable turning results — order directly via Metav Werkzeuge or request advice from our consultants. TPMT16T308-PS AH725 — ISO turning insert TPMT 16T308 for turning (0.8 mm radius, PS chipbreaker) by Tungaloy A TPMT16T308-PS AH725 ISO turning insert designed for reliable external and internal turning where process security and consistent chip formation are required Triangular ISO insert TPMT16T308-PS AH725 PVD-coated carbide, universal for steel 0.8 mm corner radius for smooth profiling 11° clearance angle for secure cutting Cylindrical hole with single-sided 40°–60° countersink Stable cutting with a universal, PVD-coated grade The AH725 grade is a PVD-coated carbide engineered as a universal, fracture-resistant option for machining both steel and rostfreier Stahl. This composition supports reliable chip formation and enhanced wear resistance under mixed-material production conditions. The chipbreaker PS is optimised to control chip flow for a broad range of feed rates, which reduces the likelihood of edge chipping during light to medium cutting. For workshops processing variable batch sizes, the combination of this grade and chipbreaker improves process security and reduces unplanned tool changes, leading to more predictable cycle times. Geometry engineered for repeatable surface quality The insert’s triangular form and ISO 16T308 designation deliver an included angle of 60°, while the 0.8 mm corner radius balances profile strength with surface finish. A 3.97 mm thickness increases edge support for interrupted cuts, and the 11° clearance angle minimises rubbing on the flank face, preserving dimensional accuracy. These geometry choices make the insert suitable for contouring, profiling and modest semi-finishing, where a controlled contact area and consistent chip section are required to achieve repeatable part tolerances and improved surface appearance. Designed for secure clamping and system compatibility Compatibility with a toolholder is determined by insert form, clearance angle, tolerance class, fixing method, size and thickness; therefore the cylindrical hole with single-sided countersink (40°–60°) ensures a secure location and consistent seat in compatible TPMT holders or boring bars. The cutting system typically comprises the ISO insert, the matching external holder or boring bar, and a shim/clamp set with replacement screws. When specifying holders, attention to tolerance and seat geometry is essential to maintain the insert’s intended cutting angle and repeatability across production batches. Operational benefits that support productivity For external and internal turning operations, the TPMT16T308-PS AH725 insert offers a pragmatic balance of tool life, chip control and versatility. The universal AH725 grade reduces the need for frequent index changes when switching between different steel alloys, while the PS chipbreaker helps maintain continuous machining under varying feed conditions. This results in fewer interruptions, improved uptime and consistent batch quality — advantages that translate directly into smoother production flow and lower total machining cost per part. Contact Metav Werkzeuge for tailored application advice on Tungaloy turning inserts and to confirm holder compatibility and delivery options Technical data Article number: 6856684 Manufacturer SKU: TUN6856684 SKU: 6856684-Tungaloy Name: TPMT16T308-PS AH725 Facts Size: 16 Thickness: 3.97 mm Corner radius: 0.8 mm Clearance angle: 11° Included angle: 60° Special features Material: Carbide (Hartmetall) Coating/grade: AH725, PVD Chipbreaker: PS Shape: Triangular Hole: Cylindrical hole with single-sided countersink (40°–60°) Application: Turning (external and internal) FAQ What materials is this insert intended for? The AH725 grade is formulated for machining steel and rostfreier Stahl, providing a universal option where material mixes occur and process reliability is important. What does the PS chipbreaker do? The PS chipbreaker governs chip shape and evacuation, promoting controlled chips and reduced edge chipping when using the TPMT16T308-PS insert. Which holder characteristics must be checked for compatibility? Compatibility is based on insert form, clearance angle, tolerance class, fixing method, size and thickness; the TPMT16T308-PS requires a holder matching the ISO seat for triangular TPMT inserts with a cylindrical hole and countersink. Is the 0.8 mm corner radius suitable for finishing? A 0.8 mm corner radius offers a compromise between profile accuracy and edge strength; it is suitable for light finishing and profiling while supporting improved edge stability over very small radii. Can the insert cope with interrupted cuts? The combination of 3.97 mm thickness and the AH725 grade gives the insert resistance to edge breakouts, making it capable of handling moderate interruptions in turning operations. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
TPMT 16T308 AH725 Wendeplatten - Tungaloy
TPMT 16T308 AH725 ISO-Drehwendeschneidplatte zum Drehen — Tungaloy Der TPMT 16T308 AH725 ist eine ISO-genormte Drehwendeschneidplatte für präzises Außen- und Innendrehen mit PVD-beschichtetem Hartmetall TPMT 16T308 AH725, PVD-beschichtetes Hartmetall Universelle Sorte für Stahl und rostfreie Stähle Zylindrisches Loch mit einseitiger Senkung 40°–60° Eckenradius 0,8 mm, Plattendicke 3,97 mm Dreieckige Plattenform, Normgröße 16 Prozesssicherheit bei wechselnden Werkstoffen fördern Die TPMT16T308-PSS Wendeplatte wurde für das Drehen entwickelt und bietet mit der Sorte AH725 eine ausbruchfeste, universelle Lösung für Stahl und rostfreie Stähle. Durch die Kombination aus PVD-Beschichtung und dem Spanbrecher PSS ergibt sich eine stabile Spanbildung, die insbesondere bei wechselnden Werkstoffen und kleineren Werkzeugaufbauten die Prozesssicherheit erhöht. Anwender profitieren von konstanter Performance und reduzierten Ausschussraten. Beschichtung und Material für längere Standzeit Gefertigt aus Hartmetall und versehen mit einer PVD-Beschichtung, liefert die Platte verbesserten Verschleißschutz und hohe Warmfestigkeit. PVD steht für Physical Vapor Deposition; diese Dünnschicht schützt die Schneidkante gegen Abrasion und ermöglicht höhere Schnittgeschwindigkeiten bei gleichbleibender Kantenstabilität. Das reduziert Rüstkosten und verlängert Intervalle zwischen Plattenwechseln. Systemintegration und Passgenauigkeit sichern Die Plattenkompatibilität zum Halter richtet sich nach Form, Freiwinkel, Toleranzklasse, Befestigung, Größe und Dicke. Achten auf die korrekte Kombination von Halter und Unterlage, damit die dreieckige Platte mit Eckenradius 0,8 mm und Freiwinkel 11° optimal positioniert ist. Die Auslegung des Spanbrechers sollte entsprechend Werkstoff, Bearbeitungsart und Maschinenstabilität gewählt werden; so lassen sich Vibrationen und Kantenausbrüche gezielt minimieren. Anwendungsempfehlung für Fertigung und Werkstatt Diese Wendeschneidplatte eignet sich für Serien- und Einzelteilfertigung, wo Prozesssicherheit und Flexibilität gefordert sind. Besonders in Betrieben mit wechselnden Losgrößen und unterschiedlichen Stahlgüten sorgt die universelle Sorte AH725 für zuverlässige Zerspanungsergebnisse. Für optimale Resultate die Plattengeometrie an den Schnittwert und Spannungsverhältnisse anpassen. Empfehlung: Die TPMT 16T308 AH725 von Tungaloy wählen für robuste Werkstückbearbeitung und verbesserte Prozesssicherheit — bei Fragen oder Bedarf an technischen Details gerne Kontakt aufnehmen via info@metav-werkzeuge.com oder telefonisch unter +49 2822 7131930 Produktmerkmale Artikelnummer: 6865203 Marke: Tungaloy Serie: ISO-Drehwendeschneidplatten Bezeichnung: TPMT16T308-PSS AH725 Hersteller SKU: TUN6865203 Fakten Eckenradius: 0,8 mm Winkel: 60° Freiwinkel: 11° Plattendicke: 3,97 mm Plattengröße: 16 Besonderheiten Schneidstoff: Hartmetall Beschichtung: AH725 (PVD-beschichtet) — verschleißfest, hohe Prozesssicherheit Spanbrecher: PSS — für stabile Spanbildung Loch: mit Loch Lochstil: zylindrisches Loch + einseitige Senkung (40°–60°) Einsatz: Drehen Modellserie: ISO-Drehwendeschneidplatten FAQ Was bedeutet die Bezeichnung TPMT 16T308? Die Bezeichnung beschreibt die ISO-Form und Größe: TPMT steht für die Plattenform, 16T308 ist der ISO-Code der Plattengröße und Geometrie; zusammen mit der Sorte AH725 ergibt sich die vollständige Typenbezeichnung der Wendeplatte von Tungaloy. Für welche Werkstoffe ist die AH725-Sorte geeignet? Die Sorte AH725 ist universell ausgelegt und eignet sich besonders für Stahl und rostfreie Stähle; sie bietet ausbruchfeste Eigenschaften und stabile Spanbildung bei wechselnden Werkstoffen. Welche Vorteile bietet der Spanbrecher PSS? Der Spanbrecher PSS wurde entwickelt, um kurze, kontrollierte Späne zu erzeugen; das erhöht die Prozesssicherheit, vermindert Verwicklungen und erleichtert die Abfuhr der Späne in automatisierten Anlagen. Wie wichtig ist der Freiwinkel von 11° für die Anwendung? Der Freiwinkel 11° beeinflusst Schneidkrafteintrag und Spanformung; er ist insbesondere bei universellen Anwendungen sinnvoll, um eine ausgewogene Kombination aus Kantenstabilität und Schnittleistung zu erreichen. Welche Plattendicke ist zu berücksichtigen? Die Plattendicke beträgt 3,97 mm; sie ist relevant für die Spannkraft im Halter und die Stabilität der Schneidkante, besonders bei höherem Vorschub. Hersteller: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenzeichen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers.
TPMT 16T308 AT9530 Wendeplatten - Tungaloy
Take advantage of precise finishing, consistent wear resistance and an optimised chipbreaker geometry to improve part quality and process stability. Order the inserts directly via Metav Werkzeuge or consult our specialists for selection and holder compatibility. TPMT16T308-PS AT9530 triangular turning insert (16T308) for turning – Tungaloy The TPMT16T308-PS AT9530 is an ISO-standard triangular turning insert engineered for finishing and light machining of steel, emphasising superior surface quality and uniform tool wear. ISO triangular insert TPMT 16T308 format Cermet grade AT9530 for fine finishing 0.8 mm corner radius for excellent surface Cylindrical hole with 40°–60° countersink High-quality cermet for improved finish and consistency The coated cermet grade AT9530 delivers a clear benefit where surface quality is paramount. Designed for finishing and light machining of steel, this grade combines a wear-resistant coating with a stable substrate to produce a uniform wear pattern and consistent component quality over time. The material selection reduces microchipping and promotes predictable tool life, which supports process planning and reduces unplanned downtime. The result is improved first-pass yield and fewer rework cycles. Geometry engineered for secure clamping and predictable chips The insert’s triangular geometry with a 60° included angle and 0.8 mm corner radius balances edge strength and fine finishing capability. A relief of 11° ensures correct cutting engagement while the 3.97 mm thickness contributes to mechanical stability in the holder. The part is supplied with a cylindrical hole and a single‑side countersink (40°–60°) that facilitates secure clamping in compatible toolholders. The PS chipbreaker supports controlled chip formation during finishing passes, making chip evacuation more reliable and reducing risk of surface damage. Practical compatibility and recommended applications This ISO-format insert is intended for both external and internal turning operations in steel when the priority is surface finish rather than heavy material removal. Compatibility with a holder depends on form, relief, tolerance class, clamping method, size and thickness, so matching these parameters in the tool system is essential for achieving the advertised performance. When paired with a suitable ISO TPMT-capable holder, the insert provides a stable cutting edge and predictable behaviour for short-series production and finishing cuts. Productivity and machining advice Using a coated cermet insert in finishing frequently reduces the need for secondary polishing and can shorten cycle times by delivering acceptable surface roughness in a single pass. The combination of AT9530 coating and a carbide substrate gives a balance between edge life and surface integrity; select cut parameters that favour moderate feeds and finishing speeds to exploit the grade’s strengths. For interrupted cuts or heavy roughing, consider a more robust grade optimised for higher stock removal. Contact Metav Werkzeuge for tailored advice on holder selection and to request Tungaloy TPMT16T308-PS AT9530 inserts; email info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: 6773754 Manufacturer SKU: TUN6773754 Metav SKU: 6773754-Tungaloy Model series: ISO-Drehwendeschneidplatten Name: TPMT16T308-PS AT9530 Facts Size: 16 mm Thickness: 3.97 mm Corner radius: 0.8 mm Relief angle: 11° Included angle: 60° Special features Shape: triangular Chipbreaker: PS Grade: AT9530 (coated cermet) Material: carbide Hole: cylindrical hole with single‑side countersink (40°–60°) Application: turning; suitable for finishing and light machining of steel Compatibility: determined by form, relief, tolerance class, clamping, size and thickness FAQ Which machining tasks suit this insert best? The TPMT16T308-PS AT9530 is optimised for finishing and light machining of steel, where surface finish and consistent wear are priorities. How does the 0.8 mm corner radius affect results? A 0.8 mm corner radius on the TPMT16T308-PS AT9530 increases edge strength and promotes a smoother surface, making it well suited to fine finishing passes. Which holder features are required for correct fit? Compatibility requires a holder that matches the ISO 16T308 form, the insert’s 11° relief, 16 mm size and 3.97 mm thickness; secure clamping is achieved via the cylindrical hole with the specified countersink. Is the insert suitable for internal turning operations? Yes, the TPMT16T308-PS AT9530 can be used for both external and internal turning, provided the holder geometry supports the triangular ISO insert form. What performance can be expected regarding wear and surface quality? The coated AT9530 cermet grade offers uniform wear and is focused on producing high surface quality during finishing; for heavier stock removal, a different grade is recommended. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
TPMT 16T308 GT9530 Wendeplatten - Tungaloy
Take advantage of the combination of a coated cermet grade (GT9530) and a defined 0.8 mm nose radius to achieve consistent finishing and longer tool life in stable turning operations; order the insert directly via Metav Werkzeuge or consult the technical team for holder compatibility. TPMT16T308-PSS GT9530 ISO turning insert for finishing and light universal turning, Tungaloy A TPMT16T308-PSS GT9530 indexable turning insert designed for finishing to light universal turning on steel, combining a coated cermet grade with an optimised chipbreaker for improved surface quality and extended interval between indexings. Coated cermet grade GT9530 for wear resistance ISO triangular insert 16T308, 60° geometry 0.8 mm nose radius for superior surface finish Central hole with cylindrical seat and 40°–60° countersink Consistent fine finishing with a wear-resistant cermet grade The GT9530 coated cermet is formulated for finish to light general-purpose turning of steel where surface integrity and longevity are priorities. The combination of a hard cermet top layer and an engineered coating reduces flank wear under stable cutting conditions, so fewer indexings are required and part finishing is more consistent. The 0.8 mm nose radius produces a fine surface without sacrificing dimensional control; this radius, together with the insert’s edge preparation, helps to achieve repeatable part quality across batches while keeping tool-change downtime low. Secure seating and precise geometry for reliable clamping A triangular 60° insert form provides rigidity and flexible orientation in ISO holders, while the central cylindrical hole plus a one-sided countersink (40°–60°) ensures positive clamping and repeatable positioning. The nominal thickness of 3.97 mm and the ISO designation 16T308 support a standardised system build consisting of a matched external holder or boring bar, backing pad and clamping set. Compatibility depends on form, clearance angle, tolerance class, fastening method, size and thickness, so selecting the correct holder and clamp is decisive for process security and tool life. Improved machining efficiency for steel with a PSS chipbreaker The integrated PSS chipbreaker is optimised for finishing cuts and light turning, promoting stable chip formation for steels and reducing the risk of built-up edge. Under stable machine and workpiece conditions, the grade offers extended life while maintaining an excellent surface finish, which can lower downstream dressing or polishing effort. The economic advantage arises from reduced frequency of insert changes and from predictable performance in repetitive production, which supports planning and reduces unplanned stoppages. Workshop-ready specifics for easy integration and replacement This ISO-standard insert is supplied in the TPMT form and is intended for use as part of a complete turning system: ISO insert, matching external holder or boring bar, backing pad/clamp set and replacement screws. The substrate is a cemented carbide base with a coated cermet cutting layer, combining toughness and wear resistance for finishing tasks. The product is identified under manufacturer article number 6998365 and manufacturer SKU TUN6998365, which simplifies procurement and inventory. The triangular form, centre hole style and precise clearance angle allow straightforward replacement without special modifications to standard ISO clamping systems. Contact Metav Werkzeuge for application-specific advice on Tungaloy inserts and to confirm holder compatibility and availability; phone +49 2822 7131930 or email info@metav-werkzeuge.com Technical Data Article number: 6998365 Manufacturer SKU: TUN6998365 SKU: 6998365-Tungaloy Model series: ISO turning inserts Core numerical data Insert size: 16 mm Insert thickness: 3.97 mm Nose radius: 0.8 mm Clearance angle: 11° Insert geometry/ISO: 16T308 Main angle: 60° Manufacturer article number: 6998365 Designs and special features Coating / grade: GT9530 Cutting material type: coated cermet Chipbreaker: PSS Insert form: triangular Hole style: cylindrical hole + one-sided countersink (40°–60°) Typical application: external and internal turning Material suitability: designed for steel; suited to finish to light universal turning FAQ What materials is this insert suited for? The TPMT16T308-PSS GT9530 insert is specified for turning steel in finishing to light universal operations; the GT9530 coated cermet supports good surface finish and extended life under stable conditions. Which holders are compatible with this insert? Compatibility is defined by the insert form, clearance angle, tolerance class, fastening, size and thickness; use ISO triangular turning holders designed for 16T308 inserts with appropriate clamping and backing pad geometry. How does the PSS chipbreaker influence machining? The PSS chipbreaker promotes stable chip formation during finishing cuts, reducing built-up edge and supporting consistent surface quality when machining steel under stable setups. What are the key geometric specifications to check before purchase? Verify the 16 mm inscribed circle size, 3.97 mm thickness, 0.8 mm nose radius and 60° geometry to ensure correct fit and performance in the intended holder. How is the insert identified for reordering? Reorder using the manufacturer article number 6998365 or the SKU 6998365-Tungaloy; the manufacturer SKU TUN6998365 is also a reliable reference. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
TPMT 16T308 GT9530 Wendeplatten - Tungaloy
Benefit from the wear-resistant GT9530 coated cermet and the precise 0.8 mm corner radius to achieve consistent surface finish and extended tool life in stable turning operations; compatibility with ISO holders is governed by form, relief angle and size. Order the insert directly via Metav Werkzeuge or consult our specialists for application-specific advice. TPMT 16T308 GT9530 – ISO triangular turning insert for Turning, 0.8 mm radius (Tungaloy) A TPMT16T308-PS GT9530 is an ISO triangular turning insert designed for finishing and light universal turning on steel, offering a balance of surface quality and tool life in stable setups. Wear-resistant GT9530 cermet grade 0.8 mm corner radius for superior surface finish 11° relief angle for stable cutting ISO triangular 16 mm format with centring hole High productivity through stable cutting performance The coated cermet grade GT9530 combines wear resistance with a cutting geometry tailored for finishing and light general-purpose turning on steel, yielding extended tool life and fewer changeovers. The modest 0.8 mm corner radius reduces cutting forces while maintaining an excellent surface finish, which helps to lower rework and downstream polishing effort. In stable clamping and machine conditions, the result is a measurable improvement in process efficiency and cost per component. Designed for consistent mounting and machine compatibility Compatibility with toolholders is determined by form, relief angle and precise dimensions; the insert features an 11° relief angle, a 16 mm triangle format and a central hole with a cylindrical bore plus a one-sided countersink (40°–60°). These specifications ensure repeatable seating and clamping in standard ISO holders. Clear adherence to ISO norms simplifies tool inventory and reduces setup time across multiple machines. Efficient cutting behaviour and chip control Equipped with the PS chipbreaker and a coated cermet substrate, the grade prioritises stable chip formation and a fine workpiece surface. Cermet materials provide a harder edge than conventional carbides for finishing tasks, enabling a reduction in feed-related vibration and improved dimensional stability. The coating and substrate combination supports longer cutting lengths under stable cutting conditions, translating into lower tool consumption during batch runs. Practical application guidance for turning operations Best suited for finishing and light universal turning on steel, the insert’s geometry and thin 3.97 mm plate thickness favour rigidity in supported setups. Matching insert grade and chipbreaker to workpiece material and clamping stability is essential: select this grade where surface quality and extended life outweigh aggressive metal removal. For unfamiliar materials or marginally stable setups, trial cuts at conservative feeds and speeds are advisable to validate performance. For tailored machining recommendations on Tungaloy GT9530 inserts or to check current availability, contact Metav Werkzeuge at info@metav-werkzeuge.com or call +49 2822 7131930 — our technical team will advise on holder compatibility and optimal cutting parameters. Technical data Article number: 6998378 Manufacturer SKU: TUN6998378 Label: TPMT16T308-PS GT9530 Model series: ISO turning inserts Material: carbide (Hartmetall) Grade: GT9530 Chipbreaker: PS Application: Turning Shape: triangular Size: 16 mm Corner radius: 0.8 mm Relief angle: 11° Plate thickness: 3.97 mm Hole: with hole Hole style: cylindrical hole + one-sided countersink (40°–60°) Included angle: 60° Facts Corner radius: 0.8 mm Relief angle: 11° Plate thickness: 3.97 mm Insert size: 16 mm Included angle: 60° Special features Coated cermet substrate GT9530 wear-resistant finishing grade PS chipbreaker for stable chips ISO triangular format TPMT16T308-PS Centring hole with cylindrical bore and one-sided countersink Optimised for finishing and light universal turning on steel FAQ What materials is this insert suited for? This insert is specified for finishing and light universal turning on steel; the GT9530 coated cermet provides wear resistance and good surface finish for such applications. How does the chipbreaker PS affect machining? The PS chipbreaker on the TPMT16T308-PS promotes controlled chip formation and evacuation, improving process stability and surface quality during finishing operations. Which holders are compatible with this ISO insert? Compatibility depends on holder form, relief angle (11°), tolerance class, fixation method, size and thickness; the insert requires an ISO triangular holder designed for a 16 mm insert with a central locating hole. Can the insert be used for heavy roughing? This grade and geometry are optimised for finishing to light universal turning; for heavy roughing, a more robust grade or different insert geometry should be selected. What benefits does the GT9530 cermet offer compared with conventional carbide? GT9530 cermet offers a harder edge and improved surface finish in finishing applications, extending tool life under stable cutting conditions and lowering the need for rework. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
TPMT 16T308 NS9530 Wendeplatten - Tungaloy
Take advantage of the combination of precision finishing, low cutting forces and straightforward ISO compatibility to ensure stable, high-quality turning operations; order the inserts directly via Metav Werkzeuge or consult their specialists for process matching. TPMT 16T308 NS9530 ISO turning insert — Tungaloy, uncoated cermet finishing grade The TPMT 16T308 NS9530 is an ISO triangular turning insert designed for finishing steel, optimised for continuous cuts and fine surface quality in external and internal turning applications. ISO triangular insert with central hole Uncoated cermet grade NS9530 for finishing 0.8 mm corner radius for fine surface finish 11° clearance and 60° insert angle Consistent finishing quality with uncoated cermet technology The insert offers a sharp cutting edge and low thermal sensitivity thanks to its uncoated cermet composition (grade NS9530), which is engineered for fine finishing on steel. Cermet materials combine ceramic and metallic binders to deliver a stable edge that reduces cutting forces and improves surface finish at small depths of cut. For shops aiming to standardise part quality, this results in fewer rework cycles and more predictable batch-to-batch results. The material choice also supports continuous cutting operations where a steady cut and minimal burr formation are priorities. Geometry and holder compatibility for efficient changeovers With a triangular shape, a 0.8 mm corner radius and an ISO code of 16T308, this insert fits common ISO-indexable holders when the form, clearance, tolerance class, fastening and thickness match. The insert includes a cylindrical hole with a single-sided countersink (40°–60°) for secure clamping and repeatable positioning. Explaining ISO codes: the designation indicates shape and size so that toolrooms can quickly identify compatible insert seats and clamping sets, reducing setup time and avoiding costly trial-and-error during tool changes. Practical advantages in everyday turning and process planning The chipbreaker version 24 is tuned for controlled chip formation during finishing passes, supporting both external and internal turning where continuous-cut stability is required. Thanks to the geometry and grade, the insert lowers cutting forces, which helps maintain spindle load limits and extends tool life of both the insert and holder. For technical queries or to confirm suitability for a specific workpiece, Metav Werkzeuge offers application advice by email or phone: info@metav-werkzeuge.com • +49 2822 7131930. For precision finishing with the Tungaloy NS9530 grade, contact Metav Werkzeuge for tailored application advice and rapid supply of TPMT 16T308 NS9530 inserts. Technical data Article number: 6998565 SKU: 6998565-Tungaloy Manufacturer SKU: TUN6998565 Model series: ISO turning indexable inserts Core specifications ISO designation: 16T308 Insert shape: triangular Size: 16 mm Thickness: 3.97 mm Corner radius: 0.8 mm Clearance angle: 11° Insert angle: 60° Hole style: cylindrical hole + one-side countersink (40°–60°) Materials & special features Grade: NS9530 (uncoated cermet) Substrate: cemented carbide Chipbreaker: 24 Intended application: turning — finishing and continuous cuts Typical use: external and internal turning FAQ What turning tasks is this insert best suited for? The TPMT 16T308 NS9530 insert from Tungaloy is intended primarily for finishing operations on steel, suitable for both external and internal turning where a high-quality surface is required. Why choose the NS9530 grade for finishing? NS9530 is an uncoated cermet grade that provides a sharp cutting edge with low cutting forces and excellent surface integrity, making the insert a strong choice for fine finishing with continuous cuts. How is compatibility with a holder determined? Compatibility depends on ISO designation, form, clearance angle, tolerance class, fastening, size and thickness; the TPMT 16T308 geometry and 3.97 mm thickness must match the selected holder and mounting set. Is this insert suitable for interrupted or heavy roughing cuts? The TPMT 16T308 NS9530 is optimised for continuous finishing and small depth cuts; heavy interrupted or aggressive roughing is not its primary application. What practical effect does the 0.8 mm corner radius have? A 0.8 mm corner radius improves surface finish and edge strength for finishing passes while maintaining acceptable cutting forces for stable machining. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
TPMT 16T308 NS9530 Wendeplatten - Tungaloy
TPMT 16T308 NS9530 – ISO-Drehwendeschneidplatten zum Drehen | Tungaloy Der TPMT16T308-PSS NS9530 ist eine ISO-Drehwendeschneidplatte für präzises Schlichten an Stahlwerkstücken und erzielt hohe Oberflächengüte bei niedrigen Schnittkräften Unbeschichtetes Cermet für hohe Oberflächengüte Scharfe Schneidkante, sehr niedrige Schnittkräfte Eckenradius 0,8 mm für feine Oberflächen Mit zylindrischem Loch und einseitiger Senkung ISO-genormte Form für zuverlässige Halterkompatibilität Präzise Schlichtleistung für produktive Fertigung Die TPMT16T308-PSS NS9530 liefert konstante Oberflächengüte und reduziert Nachbearbeitungsaufwand durch eine scharfe Schneidkante und geringe Schnittkräfte. Durch den Einsatz von unbeschichtetem Cermet wird eine feine Schnittsauberkeit erreicht, die besonders beim kontinuierlichen Schnitt und bei kleinen Zustellungen Vorteile bringt. Kunden profitieren von höherer Produktivität und weniger Schleifaufwand. Robustheit und Materialcharakteristik erklärt Das verwendete Cermet kombiniert keramische und metallische Anteile und bietet dadurch eine hohe Verschleißfestigkeit bei guter Kantenschärfe. Im Vergleich zu reinem Hartmetall ergibt sich ein verbessertes Oberflächenbild beim Schlichten von Stahl. Die Bezeichnung NS9530 steht für eine Schlichtsorte, die für niedrige Schnittkräfte optimiert ist und die Standzeit in stabilen Bearbeitungsbedingungen erhöht. Vielfältige Anwendung und einfache Integration Diese Wendeplatte ist für Außen- und Innendrehen ausgelegt; die Kompatibilität mit Haltern ergibt sich aus Form, Freiwinkel, Toleranzklasse, Befestigung, Größe und Dicke. Werkstätten und Lohnfertiger profitieren von der ISO-Normierung, da die Einbindung in vorhandene Werkzeugaufnahmen ohne aufwändige Anpassungen möglich ist. Für optimale Ergebnisse empfiehlt sich die Auswahl des passenden Spanbrechers und eine auf das Werkstoffpaket abgestimmte Schnittdatenwahl. Operative Vorteile und Handling Mit einem Eckenradius von 0,8 mm und einer Plattendicke von 3,97 mm erlaubt die Platte kontrollierte kleine Zustellungen und sorgt für stabile Spanbildung. Das zylindrische Loch mit einseitiger Senkung (40°–60°) gewährleistet sicheren Sitz auf gängigen Haltern und erleichtert den Wechsel durch standardisierte Befestigungselemente. Insgesamt ergibt sich ein wirtschaftlicher Einsatz bei feinbearbeitenden Schlichtoperationen. Empfehlung: Für hochwertige Schlichtbearbeitung empfehlen wir die TPMT16T308-PSS NS9530 von Tungaloy – für technische Rückfragen oder Schnittdatenberatung erreichen Sie uns per E‑Mail unter info@metav-werkzeuge.com oder telefonisch unter +49 2822 7131930 Produktmerkmale Herstellerartikelnummer: 6998541 Hersteller: Tungaloy Serie: ISO-Drehwendeschneidplatten Bezeichnung: TPMT16T308-PSS NS9530 SKU Hersteller: TUN6998541 Fakten Eckenradius: 0,8 mm Plattendicke: 3,97 mm Plattengröße: 16 mm Winkel: 60° Freiwinkel: 11° Besonderheiten Material: Hartmetall Schneidstofftyp: unbeschichtetes Cermet Sorte: NS9530 Spanbrecher: PSS Loch: mit Loch Lochstil: zylindrisches Loch + einseitige Senkung (40°–60°) Plattenform: dreieckig Einsatz: Drehen Typische Anwendung: Außen- und Innendrehen Kompatibilität: ISO-genormte Drehplatten; Halterkompatibilität über Form, Freiwinkel, Toleranzklasse, Befestigung, Größe und Dicke FAQ Für welche Bearbeitungen eignet sich die TPMT16T308-PSS NS9530 am besten? Die TPMT16T308-PSS NS9530 von Tungaloy ist als Schlichtsorte für Stahl konzipiert und eignet sich besonders für kontinuierlichen Schnitt und kleine Zustellungen beim Außen- und Innendrehen. Welche Vorteile bringt unbeschichtetes Cermet bei dieser Wendeplatte? Unbeschichtetes Cermet bietet eine scharfe Schneidkante und hohe Verschleißfestigkeit, wodurch die TPMT16T308-PSS NS9530 eine hervorragende Oberflächengüte bei Schlichtoperationen ermöglicht. Wie beeinflusst der Eckenradius die Bearbeitungsergebnisse? Der Eckenradius von 0,8 mm sorgt für feinere Kantenübergänge und eine gleichmäßige Spanbildung, was die Oberflächenqualität verbessert und Nachbearbeitung reduziert. Ist die Platte mit Standardhaltern kompatibel? Ja, die TPMT16T308-PSS NS9530 ist ISO-genormt; die Kompatibilität richtet sich nach Form, Freiwinkel, Toleranzklasse, Befestigung, Größe und Dicke und ermöglicht eine einfache Integration in gängige Haltersysteme. Hersteller: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenzeichen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers.
TPMT 16T308 NS9530 Wendeplatten - Tungaloy
Take advantage of the NS9530 uncoated cermet finishing grade, the 0.8 mm nose radius and the ISO triangular form for consistently high surface quality and low cutting forces. Order the insert directly via Metav Werkzeuge or contact the consultants for tailored advice. TPMT 16T308 NS9530 – ISO triangular turning insert for finishing by Tungaloy The TPMT16T308-23 NS9530 is an ISO‑standard triangular turning insert designed for precision external and internal turning, optimised as a finishing grade for steel components. Finishing uncoated cermet grade NS9530 Sharp cutting edge for high surface finish 0.8 mm nose radius for fine detail ISO triangular insert, 11° clearance angle Delivering superior surface finish with low cutting forces The uncoated cermet composition NS9530 is formulated as a finishing grade for steel applications, providing a sharp cutting edge and low cutting forces, which together produce a finer surface. For continuous cuts and small depths of cut the material combination reduces built‑up edge and stabilises the contact zone, so the machined component requires less post‑processing. The design is therefore particularly suited to jobs that prioritise consistent cosmetics and tight dimensional tolerances over heavy stock removal. Geometry and mounting that ensure repeatable accuracy The insert’s ISO‑standard triangular shape and 60° included angle give predictable toolpath geometry for many external and internal turning operations. The 0.8 mm nose radius balances detail and strength for finishing profiles, while the 11° clearance angle reduces flank rubbing and helps maintain a fine surface on the workpiece. Attachment relies on the specified hole style — a cylindrical hole with a one‑sided countersink (40°–60°) — and compatibility is determined by form, clearance, tolerance class, fastening, size and thickness; matching holder geometry is therefore essential for repeatable results. Workshop benefits that improve process reliability Made from a carbide‑based material and offered in an uncoated cermet variant, the insert gives stable cutting behaviour in finishing passes and supports consistent surface quality across batches. The chipbreaker 23 geometry should be selected in accordance with workpiece material and the intended depth of cut to ensure reliable chip control; correct pairing of insert grade and chipbreaker reduces downtime and scrap. Overall, this combination supports a cost‑efficient finishing strategy where component appearance and dimensional fidelity are decisive. Compatibility guidance and system overview The ISO insert is part of a system that comprises an appropriate external holder or boring bar, a support pad/clamp set and replacement screws. Plate dimensions and form must match the toolholder: plate size 16 mm, plate thickness 3.97 mm, and ISO designation 16T308 inform the correct clamping and seating. When integrating the insert into production, confirm holder clearance and tolerance class to prevent misalignment and to preserve the intended cutting geometry and surface outcome. For precision finishing tasks with Tungaloy’s NS9530 grade, contact Metav Werkzeuge for application support and order processing via info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: 6998637 Manufacturer SKU: TUN6998637 SKU: 6998637-Tungaloy Model series: ISO turning inserts Designation: TPMT16T308-23 NS9530 Application: Turning Material: Carbide Facts Nose radius: 0.8 mm Plate size: 16 mm Plate thickness: 3.97 mm Clearance angle: 11° Included angle: 60° Chipbreaker: 23 Special features Uncoated cermet finishing grade NS9530 Sharp cutting edge for high surface finish Optimised for continuous cuts and small depths of cut ISO triangular plate with cylindrical hole and one‑sided countersink (40°–60°) Compatibility determined by form, clearance, tolerance class, fastening, size and thickness FAQ What applications suit this insert best? The TPMT16T308-23 NS9530 is intended for precision external and internal turning where a finishing grade for steel is required; it excels on continuous cuts and small depths of cut. Which materials can be machined with this grade? The NS9530 uncoated cermet is principally designed for steel finishing operations; matching the chipbreaker 23 and machining parameters to the workpiece ensures optimal results with the Tungaloy insert. How is the insert mounted in the toolholder? The insert features a cylindrical hole with a one‑sided countersink (40°–60°) and must be clamped with a compatible holder and clamp set that match the insert’s form, size and thickness. What does the 0.8 mm radius mean for part finish? A 0.8 mm nose radius offers a compromise between fine surface quality and edge strength, enabling detailed profiles with minimal rounding while maintaining consistency across the component. Can this insert be used for roughing? This plate is a finishing grade and is optimised for low cutting forces and high surface finish; for heavy stock removal a dedicated roughing grade and a different chipbreaker geometry are recommended. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
TPMT 16T308 NS9530 Wendeplatten - Tungaloy
TPMT 16T308 NS9530 ISO-Drehwendeschneidplatten für Drehen — Tungaloy Die TPMT 16T308 NS9530 ist eine ISO-genormte Drehwendeschneidplatte für Außen- und Innendrehen, konzipiert als Schlichtsorte mit unbeschichtetem Cermet für hohe Oberflächengüte. TPMT16T308-PS NS9530 von Tungaloy ISO-genormte Platten für standardisierte Halterschnittstellen Unbeschichtetes Cermet für feine Oberflächengüte Scharfe Schneidkante für niedrige Schnittkräfte Zylindrisches Loch mit Senkung für sichere Befestigung Wirtschaftliche Präzision bei feinen Schnitten Die TPMT16T308-PS NS9530 liefert stabile Ergebnisse bei Schlichtbearbeitungen, weil der Cermet-Schneidstoff eine sehr scharfe Schneidkante und geringe Schnittkräfte ermöglicht. Das Resultat ist eine gleichbleibend hohe Oberflächengüte, die besonders bei kontinuierlichen Schnitten und kleinen Zustellungen Zeit beim Nachbearbeiten spart und so die Wirtschaftlichkeit in der Fertigung erhöht. Kompatibilität und einfache Montage für kleine Umrüstzeiten Dank der ISO-genormten Form und der definierten Abmessungen lässt sich die Platte unkompliziert in passende Außenhalter oder Bohrstangen einbringen. Die Kompatibilität wird durch Form, Freiwinkel, Toleranzklasse, Befestigung, Größe und Dicke bestimmt, sodass Umrüstzeiten minimiert werden und die Prozesssicherheit in Serienfertigung steigt. Zielgerichteter Einsatz und Anwendernutzen Entwickelt für das Drehen von Stahl ist diese Schlichtsorte ideal für Branchen, die auf enge Maßtoleranzen und feine Oberflächen angewiesen sind, etwa Werkzeugbau, Feinmechanik und Automotive-Komponenten. Nutzer profitieren von reduzierten Nacharbeit-Aufwänden und konsistenten Ergebnissen auch bei empfindlichen Werkstückgeometrien. Materialcharakteristik und Standzeitleistung Die Platte kombiniert die Trägerwerkstoff-Eigenschaften von Hartmetall mit der feinkörnigen Cermet-Matrix der Sorte NS9530, was eine langlebige Schneidkante bei Schlichtaufgaben gewährleistet. Die Konstruktion reduziert Ausbrüche an der Schneide und sorgt für wiederholgenaue Bearbeitungsresultate über längere Standzeiten. Wir empfehlen die TPMT16T308-PS NS9530 von Tungaloy als erste Wahl für hochwertige Schlichtoperationen; für technische Details und Bestellungen erreichen Sie Metav Werkzeuge per E‑Mail unter info@metav-werkzeuge.com oder telefonisch unter +49 2822 7131930 Produktmerkmale Artikelnummer: 6998553 Marke: Tungaloy Bezeichnung: TPMT16T308-PS NS9530 Modellserie: ISO-Drehwendeschneidplatten SKU Hersteller: TUN6998553 Daten Radius: 0,8 mm Winkel: 60° Plattengröße: 16 mm Plattendicke: 3,97 mm Freiwinkel: 11° Eckenradius: 0,8 mm Besonderheiten Material: Hartmetall Schneidstofftyp: unbeschichtetes Cermet Sorte: NS9530 — Schlichtsorte für Stahl, niedrige Schnittkräfte Spanbrecher: PS — Schlichtspanbrecher, scharfe Schneidkante Loch: mit Loch Lochstil: zylindrisches Loch + einseitige Senkung (40°–60°) Plattenform: dreieckig Anwendung: Drehen Modellserie: ISO-Drehwendeschneidplatten WPL ISO Code: 16T308 — ISO-Bezeichnung für Form und Geometrie FAQ Welche Werkstoffe bearbeitet die Platte am besten? Die TPMT16T308-PS NS9530 von Tungaloy ist als Schlichtsorte speziell für Stahl ausgelegt und bietet bei diesem Werkstoff die beste Kombination aus Oberflächengüte und Standzeit. Ist die Platte für Innen- und Außenbearbeitung geeignet? Ja, die ISO-Drehwendeschneidplatte eignet sich für Außen- und Innendrehen; die Auswahl eines passenden Spanbrechers und Halters ist entscheidend für die Prozesssicherheit. Welche Besonderheit hat die Sorte NS9530? Die Sorte NS9530 ist ein unbeschichtetes Cermet, das durch seine feine Schneidkante niedrige Schnittkräfte und eine sehr gute Oberflächengüte bei Schlichtoperationen ermöglicht. Wie beeinflusst der Freiwinkel die Anwendung? Der Freiwinkel von 11° reduziert Reibung am Werkzeug und unterstützt einen stabilen Spanfluss, was insbesondere bei feinen Zustellungen die Oberflächengüte verbessert. Welche Befestigungsart ist vorgesehen? Die Platte verfügt über ein zylindrisches Loch mit einseitiger Senkung (40°–60°), wodurch eine sichere und wiederholgenaue Befestigung im Halter möglich ist. Hersteller: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenbezeichnungen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers.
TPMT 16T308 T505 Wendeplatten - Tungaloy
Take advantage of the combination of cost-effective material grade, dependable chip control, and straightforward ISO compatibility for smooth turning operations; order the inserts directly via Metav Werkzeuge or consult our advisors for tailored recommendations. TPMT 16T308 T505 triangular turning insert for Turning — Tungaloy The TPMT16T308-CM T505 is an ISO-standard triangular turning insert engineered for economical external and internal turning of cast iron with reliable chip control. ISO-standard triangular insert CVD-coated T505 grade Chipbreaker CM for cast iron 0.8 mm nose radius, 60° geometry Economical, production-focused grade for cast-iron turning This insert combines a CVD-coated carbide substrate with the T505 grade to deliver a balance of wear resistance and cost efficiency specifically for cast-iron work. The coating enhances thermal and abrasive resistance while maintaining cutting-edge stability, so productivity improves without sacrificing tool life. The chipbreaker CM is optimised for typical chip forms in grey and nodular cast iron, reducing interruptions and the need for secondary chip handling. As a result, cycle times are more predictable and process costs decrease. Designed for straightforward integration into existing holders The insert follows the ISO-standard TPMT geometry and a 60° included angle, so compatibility with suitable external holders and boring bars is determined by form, clearance, tolerance class, fastening and thickness. The 11° clearance and the triangular form allow stable clamping and indexing; the central hole with a cylindrical bore and a one-sided countersink (40°–60°) ensures secure fastening and repeatable positioning. These design choices make retrofitting or replenishing tooling straightforward, helping to minimise machine downtime. Reliable cutting performance and surface quality A 0.8 mm nose radius provides a good compromise between strength and surface finish for many turning operations on cast iron. The CVD coating and substrate combination offers stable edge life during continuous cuts and improved resistance to notch wear in interrupted cuts. The engineered chip control minimises built-up edge and supports consistent surface roughness, meaning fewer downstream finishing operations and improved throughput. For workshops prioritising repeatable results, this combination supports consistent component quality. Practical selection and application advice Choose this insert when machining cast iron where process stability and economic performance are priorities. The chipbreaker CM suits medium to heavy feeds and helps control chips when vibration is low; if machining conditions involve unstable setups or very fine finishing, consider a different nose radius or chipformer. The insert’s thickness of 3.97 mm and size 16 give a stable contact area, while the ISO designation TPMT16T308-CM simplifies selection from tooling lists. For best results, pair the insert with a matching external holder rated for the TPMT form and verify clamping torque and seat cleanliness before cutting. Contact Metav Werkzeuge for a tailored recommendation on Tungaloy TPMT16T308-CM inserts, batch availability and application guidance via info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: 6793676-Tungaloy Manufacturer article number: 6793676 Manufacturer SKU: TUN6793676 Model series: ISO turning indexable inserts Designation: TPMT16T308-CM T505 Facts Thickness: 3.97 mm Insert size: 16 mm Included angle: 60° Clearance angle: 11° Nose radius: 0.8 mm Special features Material: Cemented carbide Coating: T505 (CVD) Chipbreaker: CM Shape: triangular Hole: with cylindrical hole + one-sided countersink (40°–60°) Application: Turning ISO designation: TPMT16T308-CM FAQ What materials is this insert best suited for? The TPMT16T308-CM T505 insert is optimised for machining cast iron; the T505 grade and chipbreaker CM provide effective chip control and wear resistance for grey and nodular cast iron. How does the chipbreaker influence performance? The CM chipbreaker shapes chips for safe evacuation during turning; this reduces interruptions and improves process reliability when using the TPMT16T308-CM insert in stable setups. Can the insert be used in existing ISO holders? Yes, the ISO-standard geometry of the TPMT16T308-CM is compatible with holders designed for TPMT inserts, provided the holder matches form, clearance, thickness and fastening specifications. What cutting results can be expected with a 0.8 mm nose radius? A 0.8 mm nose radius offers a balance between edge strength and surface finish, delivering dependable roughing and semi-finishing performance with consistent surface quality on cast iron. Is this insert suitable for interrupted cuts? The combination of CVD-coated carbide and the T505 grade gives robust edge life for many interrupted cut scenarios, though final performance depends on workpiece rigidity and cutting parameters. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com