VCMT 160404 AH6225 Wendeplatten - Tungaloy
Take advantage of the combination of a PVD‑coated carbide grade AH6225, a rhombic VCMT form with 0.4 mm corner radius, and an ISO‑compatible geometry for reliable turning of stainless steels; order the VCMT160404‑TM AH6225 directly via Metav Werkzeuge or ask our consultants if needed. VCMT160404-TM AH6225 — VCMT 160404 turning insert by Tungaloy, PVD‑coated carbide for turning A VCMT160404‑TM AH6225 ISO‑standard rhombic turning insert engineered for external and internal turning, delivering a sharp but stable cutting edge for medium‑duty machining of stainless steels PVD-coated carbide grade AH6225 for stainless steel Rhombic VCMT form with 0.4 mm corner radius TM chipbreaker for consistent chip control 35° approach angle, cylindrical hole with countersink 4.76 mm plate thickness for stable clamping High‑performance grade for stainless steel machining The VCMT160404‑TM AH6225 is based on a PVD‑coated carbide substrate and the AH6225 grade, which is engineered to balance a sharp cutting edge with the toughness required for stainless steel work. This combination reduces built‑up edge and supports consistent surface quality during medium machining and changing workpiece conditions. In practice, the result is fewer interruptions for rework and a predictable tool life that contributes to efficient cycle times and reduced overall machining cost. Geometry tailored for accuracy and secure clamping The rhombic VCMT form and the modest 0.4 mm corner radius deliver an effective compromise between edge strength and the ability to produce fine contours. The insert’s 35° approach angle improves chip flow and cutting forces in many turning set‑ups, while the 4.76 mm thickness and the cylindrical hole with one‑sided countersink (40°–60°) ensure stable seating and repeatable clamping. These geometric details make the insert suitable for both external and internal turning where positional accuracy and reliable clamping are essential. Controlled chips and stable processes with the TM chipbreaker A TM chipbreaker provides predictable chip formation across typical stainless‑steel feeds and depths of cut. The breaker is designed to divide chips into manageable segments, which reduces the risk of entanglement and improves component finish. Combined with the PVD surface, the chip control contributes directly to machining stability: fewer tool‑related stoppages, improved operator safety and a smoother downstream handling of swarf. System compatibility and application guidance This indexable insert is supplied as an ISO‑standard component and is intended to work within a system comprising a matching external holder or boring bar, backing pad/clamp set and fastening screw. Compatibility depends on the insert form, clearance (7° free angle), tolerance class, fixation and the insert’s size and thickness; therefore the choice of a suitable holder and clamping layout is essential for achieving the grade’s potential. For customers seeking guidance on holder selection or cutting parameters for specific stainless‑steel alloys, Metav Werkzeuge can provide application support and machining recommendations. For application advice or to discuss suitability for a specific turning task with Metav Werkzeuge, please contact our technical team at info@metav-werkzeuge.com or by phone on +49 2822 7131930 to arrange further consultation and ordering options. Technical Data Article number: 6947741 Manufacturer SKU: TUN6947741 SKU: 6947741-Tungaloy Model series: ISO turning inserts Product name: VCMT160404-TM AH6225 Core specifications ISO designation: 160404 Size: 16 mm Plate thickness: 4.76 mm Corner radius: 0.4 mm Clearance (free) angle: 7° Approach/wedge angle: 35° Materials & features Material: Carbide Coating: PVD Grade: AH6225 Chipbreaker: TM Plate shape: Rhombic Hole style: Cylindrical hole + one‑sided countersink (40°–60°) Application: Turning (external and internal) Compatibility: ISO‑standard system components FAQ What materials is this insert suitable for? The VCMT160404‑TM AH6225 is primarily intended for stainless steel machining; the PVD‑coated AH6225 grade is optimised to maintain a sharp, stable edge under variable conditions. Which chipbreaker is fitted and what benefit does it provide? This insert features a TM chipbreaker, which produces shorter, controllable chips to improve surface quality and reduce swarf issues in turning operations. How does the insert secure to the holder? The insert uses a cylindrical hole with a one‑sided countersink (40°–60°) and requires a matching clamping system and screw; the 4.76 mm thickness supports secure, repeatable seating. Is this insert suitable for both external and internal turning? Yes; the geometry and 35° approach angle make it appropriate for many external and internal turning tasks when used with the correct holder and set‑up. How should holders be selected for optimum performance? Holder selection should match form, free angle, tolerance class, fixation, size and thickness; Metav Werkzeuge can advise on the correct holder and cutting data for specific applications. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
VCMT 160404 AH6225 Wendeplatten - Tungaloy
VCMT 160404 AH6225 ISO-Drehwendeschneidplatte für Drehen von Tungaloy VCMT 160404 AH6225 ist eine ISO-genormte rhombische Wendeschneidplatte für präzise Außen- und Innendreharbeiten auf rostfreiem Stahl, ausgelegt für mittlere Schnittbedingungen und wechselnde Fertigungsanforderungen. Universelle Sorte für rostfreien Stahl PVD-beschichtetes Hartmetall für Standzeit Rhombische Form 16 mm, 35° Winkel Mit zylindrischem Loch und einseitiger Senkung Spanbrecher PSS optimiert Spanbildung Präzise und wirtschaftliche Bearbeitung rostfreier Werkstoffe Die PVD-Beschichtung in Kombination mit dem Hartmetall-Träger sorgt für eine ausgeglichene Mischung aus Schärfe und Stabilität, ideal für das Drehen von rostfreiem Stahl. Weniger Riefenbildung und verbesserte Spankontrolle reduzieren Nacharbeit und erhöhen die Teileausbeute. Anwender profitieren von konstanter Schnittqualität bei variierenden Schnittbedingungen, was Rüstzeiten und Ausschuss minimiert. Kompatibilität und sichere Spanngeometrie reduzieren Ausfallzeiten Die rhombische Plattenform und der definierte Winkel von 35° sowie der Freiwinkel von 7° gewährleisten einfache Einpassung in ISO-kompatible Halter. Die Ausführung mit Loch und die zylindrische Bohrung mit einseitiger Senkung (40°–60°) erlauben stabile Fixierung und einfache Wechselprozesse. Dadurch steigt die Maschinenlaufzeit, da Rüstaufwand und Vibrationsneigung sinken. Hartmetall und Beschichtung: Technologie für wiederholbare Ergebnisse Die Sorte AH6225 ist als PVD-beschichtetes Hartmetall konzipiert und bietet eine gute Balance aus Verschleißfestigkeit und Schneidkantenstabilität. PVD steht für eine dünne, haftfeste Schicht, die Wärme- und Reibungsbelastung reduziert und so die Standzeit erhöht. Für Anwender bedeutet das planbare Werkzeugkosten und höhere Prozessstabilität bei Serienfertigung. Empfehlung für Anwender und Einsatzbereiche Die Wendeschneidplatte eignet sich besonders für Lohnfertiger und industrielle Fertigungsbereiche, die Außen- und Innendrehen an rostfreien Werkstücken durchführen. Bei wechselnden Schnittbedingungen oder schwierigen Spanverhältnissen empfiehlt sich die Kombination mit passenden Haltern und dem Spanbrecher PSS, um die Spanform zu kontrollieren und Werkzeugstandzeit zu maximieren. Für produktive Zerspanung mit hoher Prozesssicherheit: Benötigen Sie Detaildaten oder Verfügbarkeit zu VCMT 160404 AH6225 von Tungaloy? Kontaktieren Sie Metav Werkzeuge per eMail info@metav-werkzeuge.com oder Telefon +49 2822 7131930 für technische Beratung und Bestellung Produktmerkmale Artikelnummer: 6831912 Marke: Tungaloy Serie: ISO-Drehwendeschneidplatten Daten Radius: 0,4 mm Eckenradius: 0,4 mm Plattendicke: 4,76 mm Plattengröße: 16 mm Winkel: 35° Freiwinkel: 7° Besonderheiten Material: Hartmetall Beschichtung: PVD-beschichtet (Sorte AH6225) Spanbrecher: PSS (optimierte Spanbildung) Form: Rhombisch Loch: mit Loch Lochstil: zylindrisches Loch + einseitige Senkung (40°–60°) Anwendung: Drehen Einsatzgebiet: rostfreier Stahl Hersteller Artikelnummer: 6831912 SKU Hersteller: TUN6831912 FAQ Welche Werkstoffe sind mit dieser Platte am besten zu bearbeiten? Die VCMT 160404 AH6225 von Tungaloy ist speziell für die Bearbeitung von rostfreiem Stahl ausgelegt und bietet dort ausgeglichene Schneidkantenstabilität und gute Spankontrolle. Welche Vorteile bietet die PVD-Beschichtung bei dieser Wendeschneidplatte? Die PVD-Beschichtung der Sorte AH6225 erhöht die Verschleißfestigkeit, reduziert Reibung und verbessert die Standzeit unter mittleren Schnittbedingungen, was zu stabileren Prozessen führt. Wie beeinflusst der Spanbrecher PSS die Zerspanung? Der Spanbrecher PSS formt die Späne kontrolliert und verhindert lange, fädige Späne bei rostfreiem Stahl, wodurch Werkzeugstandzeit und Maschinenlaufzeit verbessert werden. Welche Halter sollten gewählt werden, um die Platte korrekt zu befestigen? ISO-kompatible Außenhalter oder Bohrstangen, die Form, Freiwinkel, Toleranzklasse, Befestigung und Plattendicke unterstützen, sind geeignet. Die Ausführung mit zylindrischem Loch und Senkung ermöglicht sichere Fixierung. Ist diese Platte für Innen- und Außenbearbeitung verwendbar? Ja, die VCMT 160404 AH6225 ist für Außen- und Innendrehen geeignet; die Wahl von Spanbrecher und Bearbeitungsparametern richtet sich nach Werkstoff und Stabilität. Hersteller: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenzeichen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers.
VCMT 160404 AH6235 Wendeplatten - Tungaloy
Take advantage of the combination of PVD-coated cemented carbide, a dedicated PS chipbreaker and precision geometry for consistent productivity in turning operations; order the insert directly via Metav Werkzeuge or ask the consultants for application support. VCMT 160404 AH6235 — ISO rhombic turning insert (turning) by Tungaloy The VCMT 160404 AH6235 is an ISO-format rhombic turning insert designed for external and internal turning, offering robust performance for interrupted cuts and demanding stainless-steel applications. PVD-coated cemented carbide for durability Optimised PS chipbreaker for reliable chip control Rhombic shape 16 mm, 0.4 mm nose radius Cylindrical hole with 40°–60° countersink Consistent cutting performance for stainless applications This insert delivers repeatable results through a combination of a PVD-coated surface and a tough cemented carbide substrate. The AH6235 grade is formulated to resist adhesive wear and handle the thermal and work-hardening tendencies of stainless steels, which reduces edge breakdown during interrupted cuts. By choosing a dedicated grade and the PS chipbreaker, the tool achieves stable chip formation and fewer built-up edges, translating into longer effective tool life and fewer interruptions on the shop floor. Geometry tuned for accuracy and production efficiency The rhombic ISO 160404 form, with a 0.4 mm nose radius and a 7° clearance angle, balances cutting strength and profile fidelity. The small nose radius supports fine surface finishes while maintaining sufficient edge robustness for higher feed rates where profile control matters. The PS chipbreaker is tailored to evacuate chips efficiently in medium to heavy interrupted passes; this reduces cycle times and the need for reactive process adjustments. Compatibility with common ISO holders simplifies tool changeover and keeps spindle downtime to a minimum. Integration into stable machining processes Compatibility is determined by form, clearance angle, tolerance class, fastening method, size and thickness; the insert fits standard external holders or boring bars when matched correctly. The central hole — supplied as a cylindrical bore with a one-sided countersink (40°–60°) — ensures secure clamping and precise seating. For shops aiming to standardise inserts, the combination of PVD coating, a robust grade and the PS chipbreaker supports predictable tool life and reduced scrap rates in production lines. Contact Metav Werkzeuge today to discuss the Tungaloy VCMT 160404 AH6235 for turning applications or to arrange a tailored cutting strategy with our technical advisers; email info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: 6890230 Manufacturer SKU: TUN6890230 Dealer SKU: 6890230-Tungaloy Label: VCMT160404-PS AH6235 Facts Size: 16 mm Thickness: 4.76 mm Nose radius: 0.4 mm Clearance angle: 7° Geometric angle: 35° Centre hole: with hole Special features Material: cemented carbide Coating: PVD coating Grade: AH6235 Chipbreaker: PS Shape: rhombic Hole style: cylindrical hole + one-sided countersink (40°–60°) Application: external and internal turning, interrupted cuts, stainless steels FAQ What materials is this insert suitable for? The VCMT 160404 AH6235 is designed primarily for stainless steels and performs well in interrupted cutting conditions where increased breakout risk exists. How does the PS chipbreaker affect machining? The PS chipbreaker on the VCMT 160404 AH6235 promotes controlled chip formation and evacuation, improving surface finish and reducing the likelihood of built-up edge in medium to heavy interrupted cuts. Which holders are compatible with this ISO insert? Compatibility depends on form, clearance angle, tolerance class, fastening method, size and thickness; the insert matches standard ISO holders and external turning bars when these parameters align with ISO 160404 specifications. What is the significance of the 0.4 mm nose radius? A 0.4 mm nose radius balances profile definition and edge strength, enabling finer surface finishes without sacrificing robustness during higher feed operations. Is the insert supplied with a countersunk hole? Yes — the insert features a cylindrical centre hole with a one-sided countersink (40°–60°) to ensure secure clamping and precise seating. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
VCMT 160404 AH6235 Wendeplatten - Tungaloy
Take advantage of the combination of a tough PVD-coated carbide grade, precise ISO geometry and reliable chip control for consistent turning of difficult materials; order the insert directly via Metav Werkzeuge or ask their consultants for holder recommendations. VCMT160404-PSS AH6235 – VCMT 160404 turning insert for turning applications, Tungaloy The VCMT160404-PSS AH6235 is an ISO-standard rhombic indexable insert designed for metalcutting turning operations, especially where stainless steels and interrupted cuts require enhanced fracture resistance. ISO-standard rhombic geometry PVD-coated carbide grade AH6235 0.4 mm corner radius for precision Cylindrical hole with countersink Longer tool life and controlled wear for demanding stainless work The combination of a PVD-coated surface and the AH6235 carbide substrate provides improved resistance to built-up edge and thermal wear during turning of stainless steels and other tough alloys. This tougher grade is formulated for applications with elevated chipping risk and interrupted cuts, giving a measurable advantage in tool life and process stability. As a result, machining cycles can run longer between indexings, reducing downtime and contributing to predictable production output. Geometry that delivers repeatable accuracy and surface quality The rhombic insert form with a lead 35° angle and 7° clearance is optimised for both external and internal turning where edge integrity and surface finish matter. The small corner radius 0.4 mm helps to maintain dimensional control while allowing a compromise between strength and fine turning. The plate thickness of 4.76 mm ensures secure clamping and stability in the holder; compatibility relies on matching form, clearance, tolerance class, fastening and thickness to the selected toolholder for best results. System approach and application guidance for practical machining As part of an ISO insert system, the plate requires a suitable external holder or boring bar, appropriate shim/clamping kit and replacement screws for safe operation. The PSS chipbreaker is optimised for controlled chip formation with ductile materials and interrupted cuts, reducing the risk of built-up edge and improving swarf evacuation. Selecting the correct holder geometry and clamping method is essential for achieving the promised performance; technical specification and optimiser checks will align the insert’s advantages with the chosen machining strategy. For tailored holder recommendations and to secure VCMT160404-PSS AH6235 inserts for upcoming turning operations, contact Metav Werkzeuge for a technical consultation and quick supply solutions Technical data Article number: 6890227 Manufacturer SKU: TUN6890227 SKU: 6890227-Tungaloy Model series: ISO turning inserts ISO designation: VCMT160404-PSS Material: Carbide Grade/coating: AH6235, PVD-coated Core data Insert size: 16 mm Insert thickness: 4.76 mm Corner radius: 0.4 mm Clearance angle: 7° Lead/angle: 35° Special features Rhombic plate form PSS chipbreaker With hole: cylindrical hole + one-sided countersink (40°–60°) Suitable for turning and interrupted cuts Compatible with ISO holders (shape, clearance, tolerance, fastening, size, thickness) FAQ What materials is this insert designed for? The VCMT160404-PSS AH6235 insert from Tungaloy is formulated for stainless steels and similar tough alloys; the AH6235 grade improves resistance to chipping in interrupted cut conditions. How does the PSS chipbreaker influence performance? The PSS chipbreaker on the VCMT160404-PSS AH6235 provides controlled chip formation during turning, which supports consistent surface quality and reduces the risk of built-up edge when machining ductile materials. What dimensions and geometry should be considered when choosing a holder? Match the holder to the VCMT160404-PSS AH6235 by shape, 7° clearance, tolerance class, fastening method, size (16 mm) and thickness (4.76 mm) to ensure stable clamping and repeatable turning results. Is this insert suitable for interrupted cuts? Yes; the AH6235 PVD-coated carbide grade and robust edge preparation of the VCMT160404-PSS AH6235 make it particularly suitable for interrupted cuts and applications with increased breakout risk. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
VCMT 160404 AH725 Wendeplatten - Tungaloy
Die Kombination aus PVD-beschichtetem AH725 Hartmetall, dem PSF Spanbrecher und der ISO‑Konformität sorgt für prozesssichere Zerspanung bei Stahl und rostfreien Stählen; Bestellung direkt über Metav Werkzeuge möglich oder alternativ Beratung durch unsere Expertinnen und Experten anfragen. VCMT 160404 AH725 — ISO turning indexable insert (PVD‑coated carbide, Tungaloy) A VCMT160404-PSF AH725 indexable insert designed for external and internal turning applications, combining a rhombic geometry with a 35° approach angle for versatile metalcutting tasks. PVD-coated AH725 carbide grade PSF chipbreaker for controlled chip formation ISO‑standard rhombic insert shape 7° clearance angle for stable cutting Cylindrical hole with single‑side countersink Reliable performance and predictable tool life The PVD‑coated AH725 grade delivers a balance of toughness and wear resistance that is optimised for a wide range of steels and stainless steels. The PSF chipbreaker promotes short, controllable chips under varied cutting conditions, reducing interruptions and tool‑related scrap. Thanks to the ISO standard geometry and the rhombic form factor, insert fitment and repeatability are straightforward; the combination of a 35° approach angle and a 0.4 mm corner radius supports stable chip flow and predictable surface finish. This section explains how material properties translate into higher uptime and fewer tool changes. Compatibility and straightforward system integration Integration into existing tool systems is determined by insert form, clearance angle, tolerance class, fastening and exact dimensions. The insert is supplied with a cylindrical hole plus a single‑side countersink (40°–60°) to match common mounting screws and clamping systems. The plate thickness of 4.76 mm and a nominal size of 16 mm make the component compatible with standard external holders and boring bars. For workshop planning, the system requires an ISO insert, a matching external holder or boring bar, a shim/clamping set and spare screws; this modular approach simplifies stock keeping while ensuring rapid replacement and minimal setup time. Material grade and process security explained The AH725 designation denotes a PVD‑coated carbide engineered for universal use with a focus on breakage resistance and consistent performance when machining steels and stainless steels. PVD coating enhances resistance to abrasion and built‑up edge, thereby extending tool life in interrupted cuts and mixed‑material batches. Selecting a universal, tough grade reduces the need for multiple specialised inserts across small batch runs or changing components, offering an economical route to maintain high process security without compromising surface quality. Practical benefits for production workflows Using an ISO‑conforming, PVD‑coated insert with a dedicated chipformer yields measurable workflow advantages: fewer tool changes, improved repeatability of dimensions and reduced cycle interruptions from poor chip control. The VCMT160404‑PSF AH725 insert is particularly suitable where operators require a robust compromise between wear resistance and resistance to chipping — for example, in component turning with varying part geometries or mixed steel grades. Clear specifications (35°, 7° clearance, 4.76 mm thickness) allow reliable programming of cutting data and predictable tool life calculations. Contact Metav Werkzeuge today for a tailored recommendation based on machining data, or request further technical specifications and cutting parameter guidance directly from Metav Werkzeuge. Technical Data Article number: 6864867 Manufacturer SKU: TUN6864867 Brand: Tungaloy Type: VCMT160404‑PSF AH725 indexable insert Material: carbide (PVD‑coated) Chipformer: PSF Numbers / Core technical data Corner radius: 0.4 mm Approach angle: 35° Clearance angle: 7° Plate thickness: 4.76 mm Plate size: 16 mm Designs / Special features Rhombic insert geometry Cylindrical hole with single‑side countersink (40°–60°) Universal, fracture‑resistant AH725 grade Suitable for steel and stainless steels ISO‑conforming turning insert FAQ What materials is this insert suitable for? The VCMT160404‑PSF AH725 insert is designed for machining steels and stainless steels, benefitting from the AH725 PVD‑coated carbide for balanced wear resistance and toughness. How does the PSF chipbreaker affect machining? The PSF chipbreaker on the VCMT160404‑PSF AH725 produces short, controlled chips that reduce machine downtime and improve safety during turning operations. Can this insert be used in existing ISO holders? Yes; the insert follows ISO geometry and the cylindrical hole with single‑side countersink matches common clamping systems, allowing integration with compatible external holders and boring bars. What advantages does the PVD coating provide? PVD coating on the AH725 grade increases resistance to abrasive wear and helps prevent built‑up edge, which improves surface finish consistency and prolongs effective tool life. Which spare components are typically required for a complete system? A complete turning system for this insert comprises the ISO insert, a matching external holder or boring bar, a shim/clamping set and replacement screws to ensure secure mounting and fast changeovers. Manufacturer/Responsible: Tungaloy‑NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand‑new product from the manufacturer.
VCMT 160404 AH725 Wendeplatten - Tungaloy
Take advantage of the universal PVD-coated AH725 grade and ISO compatibility to secure consistent cutting performance and extended edge life; order the inserts directly via Metav Werkzeuge or contact the consultants for selection assistance. VCMT160404-PS AH725 ISO turning insert (VCMT 160404) by Tungaloy — PVD carbide for turning VCMT160404-PS AH725 is a PVD-coated carbide ISO insert designed for robust external and internal turning, offering a universal, breakage-resistant grade suited to mixed production environments VCMT rhombic insert, ISO 160404 PVD-coated carbide AH725 for steel and stainless Designed for external and internal turning Cylindrical hole with single-sided countersink Reliable cutting for mixed-material production The AH725 grade is a PVD-coated carbide developed as a universal, breakage-resistant option for machining steel and stainless steel. In practise, the combination of a wear-resistant coating and a tough substrate reduces unexpected edge failures and maintains cutting geometry over longer tool life. This reliability translates into fewer interruptions for tool changes and more predictable cycle times, which is particularly valuable in series production with varying workpiece materials. Engineered geometry for secure clamping and predictable accuracy As an ISO 160404 rhombic insert, the geometry and mounting features determine compatibility with the toolholder: form, relief angle, tolerance class, fastening and thickness must match the clamping system. Key dimensions include an inscribed size of 16 mm, corner radius 0.4 mm, relief angle 7°, and a plate thickness of 4.76 mm; the insert is supplied with a cylindrical hole and a single-sided countersink (40°–60°) to suit standard clamping screws. These defined parameters ensure repeatable seating and stable cutting conditions, reducing vibration and improving dimensional consistency on turned components. Built for process security and small-tool productivity The chipbreaker type PS paired with the AH725 grade is suited to smaller tools and operations where process security is critical. The insert’s design supports reliable chip control and surface finish while reducing the risk of catastrophic edge breakout during interrupted cuts. In short runs or mixed-batch production, fewer tool failures and steady wear characteristics contribute to lower overall machining costs and higher throughput. The insert is compatible with standard holder systems as part of an ISO turning insert setup, enabling straightforward integration into existing tooling stocks. For reliable turning performance with Tungaloy AH725 inserts, contact Metav Werkzeuge for expert selection and prompt delivery: info@metav-werkzeuge.com | +49 2822 7131930 — Metav Werkzeuge is ready to advise on holder compatibility and optimal chipbreaker choice. Technical data Article number: 6856694-Tungaloy Manufacturer article number: 6856694 Manufacturer SKU: TUN6856694 Label: VCMT160404-PS AH725 Facts ISO designation: 160404 Inscribed circle / size: 16 mm Corner radius: 0.4 mm Relief angle: 7° Insert thickness: 4.76 mm Included angle: 35° Special features Grade / coating: AH725 (PVD-coated carbide) Chipbreaker: PS Shape: rhombic Hole style: cylindrical hole with single-sided countersink (40°–60°) Typical application: external and internal turning System: ISO turning insert; compatible with matching holder, clamp set and screws Material base: carbide FAQ What materials are suitable for this insert? The VCMT160404-PS AH725 insert from Tungaloy is intended for machining steel and stainless steel, providing universal performance across a broad material range. Which chipbreaker is fitted and what is its benefit? This insert features the PS chipbreaker, which is designed to support reliable chip control and consistent surface finish in a variety of turning operations. How is compatibility with the toolholder determined? Compatibility depends on insert form, relief angle, tolerance class, fastening method, size and thickness; matching these parameters ensures correct clamping and repeatable positioning of the Tungaloy insert. Is the insert suitable for small-tool applications and mixed batches? Yes, the AH725 grade is specifically suited to smaller tools and operations with changing workpiece materials where process security and reduced edge breakout are priorities. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
VCMT 160404 AH725 Wendeplatten - Tungaloy
VCMT 160404 AH725 — Drehwendeschneidplatte für Drehen (Tungaloy) Die VCMT160404-PSS AH725 ist eine ISO-genormte, PVD-beschichtete Wendeschneidplatte für Außen- und Innendrehen mit robustem Spanformer für prozesssichere Bearbeitung ISO-genormte rhombische Wendeschneidplatte PVD-beschichtetes Hartmetall für hohe Standzeit Speziell geeignet für Stahl und rostfreie Stähle Zylindrisches Loch mit einseitiger Senkung 40°–60° Eckenradius 0,4 mm und Freiwinkel 7° Hohe Standzeit durch PVD-Beschichtung und Hartmetall Die Kombination aus PVD-Beschichtung und Hartmetall sorgt für gleichbleibende Schneidkantenzustände bei Serienbearbeitung. Durch die Beschichtung reduziert sich der Wärmeeintrag an der Schneidkante, was die Werkzeugstandzeit erhöht und die Stillstandszeiten in der Fertigung reduziert. Das Ergebnis ist eine zuverlässige Performance bei wechselnden Werkstoffen und anspruchsvollen Zerspanungsbedingungen. Präzise Anwendung im Außen- und Innendrehen Die Platte ist für Drehen ausgelegt und liefert dank ISO-Genormung und definierter Form-Freiwinkel-Toleranzen vorhersehbare Einspann- und Laufwerte. Der Spanformer PSS unterstützt stabile Spanbildung, wodurch die Bearbeitung von langen Spänen und wechselnden Schnittbedingungen sicherer wird. Kompatibilität wird über Form, Freiwinkel, Befestigung und Dicke sichergestellt, was die Auswahl des passenden Halters erleichtert. Prozesssicherheit und flexible Werkstoffabdeckung Diese Sorte AH725 wurde als universelle, ausbruchfeste Lösung entwickelt und deckt sowohl Stahl als auch rostfreie Stähle ab. Für Anwender bedeutet das weniger Sortenwechsel im Werkzeugbestand und höhere Verfügbarkeit der Maschine. Kleine Werkzeuge profitieren dabei von stabiler Spanformung und kontrollierter Schneidkantengeometrie, was Rüstzeiten und Ausschuss reduziert. Empfehlung: Für prozesssichere Serienbearbeitung die VCMT160404-PSS AH725 von Tungaloy über Metav Werkzeuge anfragen: info@metav-werkzeuge.com • Tel. +49 2822 7131930 Produktmerkmale Artikelnummer: 6865370 Hersteller: Tungaloy Serie: ISO-Drehwendeschneidplatten Bezeichnung: VCMT160404-PSS AH725 SKU: 6865370-Tungaloy Fakten Eckenradius: 0,4 mm Plattendicke: 4,76 mm Plattengröße: 16 mm Freiwinkel: 7° Winkel: 35° Besonderheiten Material: Hartmetall Schneidstoff: PVD-beschichtetes Hartmetall Sorte: AH725 — universelle, ausbruchfeste Sorte für Stahl und rostfreie Stähle Spanbrecher: PSS — optimierter Spanformer für stabile Spanbildung Plattenform: rhombisch Lochstil: zylindrisches Loch + einseitige Senkung (40°–60°) Einsatz: Drehen Systemaufbau: ISO-genormte Drehplatte, passende Halter erforderlich FAQ Welche Werkstoffe lassen sich mit der VCMT160404-PSS AH725 bearbeiten? Die VCMT160404-PSS AH725 von Tungaloy ist primär für Stahl und rostfreie Stähle ausgelegt; die universelle AH725-Sorte ermöglicht zudem zuverlässige Ergebnisse bei wechselnden Werkstoffen. Welches Plattensystem und welche Halter passen zur Platte? Die Platte gehört zur Serie ISO-Drehwendeschneidplatten; passende Außenhalter oder Bohrstangen mit Übereinstimmung in Form, Freiwinkel, Befestigung, Größe und Dicke sind erforderlich. Was bedeutet PSS bei dieser Wendeplatte? Der Spanbrecher PSS ist ein optimierter Spanformer, der für stabile Spanbildung sorgt und so die Prozesssicherheit bei der Verwendung der VCMT160404-PSS AH725 erhöht. Welche Vorteile bietet die AH725-Sorte gegenüber Standardvarianten? Die AH725-Sorte kombiniert Ausbruchsicherheit und breite Werkstoffabdeckung, was zu längeren Werkzeugstandzeiten und geringerem Sortenaufwand im Werkzeuglager führt. Hersteller: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenzeichen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers.
VCMT 160404 AH8005 Wendeplatten - Tungaloy
VCMT 160404 AH8005 ISO-Drehwendeschneidplatten für Drehen von Tungaloy VCMT160404 AH8005 bietet verschleißfestes PVD-beschichtetes Hartmetall für die Bearbeitung hitzebeständiger Legierungen und harter Werkstoffe PVD-beschichtetes Hartmetall für hohe Standzeit Rhombische Form, 16 mm, mit zylindrischem Loch Einseitiger Spanbrecher optimiert Spanbildung Passend für ISO-Drehhalter, Freiwinkel 7° Langlebigkeit durch präzise Beschichtung und Schneidstoff Die AH8005 Sorte kombiniert PVD-beschichtetes Hartmetall mit einer auf Dauerhaftigkeit ausgelegten Schneidkante. Dadurch ergibt sich eine verbesserte Verschleißfestigkeit bei der Bearbeitung hitzebeständiger Legierungen, was Standzeiten verlängert und Werkzeugwechsel reduziert. PVD steht für physikalische Gasphasenabscheidung und bildet eine dünne, harte Schicht, die die Schnittkante schützt und Temperaturwechseln widersteht. Präzise Passform für ISO-Systeme und sichere Spannlösung Die Normierung als ISO-Drehwendeschneidplatte gewährleistet die Kompatibilität zu standardisierten Haltern. Entscheidend sind Form, Freiwinkel, Toleranzklasse, Befestigung, Größe und Dicke. Die rhombische Plattenform mit zylindrischem Loch und einseitiger Senkung (40°–60°) sorgt für stabile Positionierung und einfache Montage auf Außenhalter oder Bohrstangen, wodurch Wiederholgenauigkeit und Prozesssicherheit in der Serienfertigung erhöht werden. Geeignete Einsatzfelder und Bearbeitungsstrategie Diese Wendeplatte eignet sich insbesondere für Außen- und Innendrehen, wenn stabile Schnittbedingungen vorliegen. Der einseitige Spanbrecher ist auf kontrollierte Spanbildung ausgelegt; Sorte und Spanformer sind nach Werkstoff und Bearbeitungsart auszuwählen. Für CNC-Fertigung und Serienprozesse bietet das Produkt eine gute Kombination aus Produktivität und Oberflächengüte, speziell bei anspruchsvollen, hitzebeständigen Werkstoffen. Wirtschaftlichkeit durch reduzierte Stillstandzeiten Die Kombination aus stabiler Spanbildung, hoher Verschleißfestigkeit und ISO-Kompatibilität führt zu weniger Werkzeugwechseln und gleichbleibender Bearbeitungsqualität. Damit entsteht ein wirtschaftlicher Vorteil: höhere Produktivität pro Werkzeugwechsel und planbare Prozesskosten. Die VCMT Geometrie mit 0,4 mm Eckenradius ermöglicht präzise Rundläufe und konstante Maßhaltigkeit bei Serien. Empfehlung: Für stabile Zerspanungsvorgänge die VCMT160404 AH8005 von Tungaloy anfragen und technische Beratung über Metav Werkzeuge in Anspruch nehmen, E‑Mail: info@metav-werkzeuge.com, Telefon: +49 2822 7131930 Produktmerkmale Artikelnummer: 6747802 Marke: Tungaloy Serie: ISO-Drehwendeschneidplatten Bezeichnung: VCMT160404 AH8005 SKU Hersteller: TUN6747802 Fakten Eckenradius: 0,4 mm Winkel: 35° Freiwinkel: 7° Plattendicke: 4,76 mm Plattengröße: 16 mm Besonderheiten Material: Hartmetall Beschichtung: PVD (physikalische Gasphasenabscheidung) Sorte: AH8005 Plattenform: rhombisch Loch: mit Loch Lochstil: zylindrisches Loch + einseitige Senkung (40°–60°) Spanbrecher: einseitig Einsatz: Drehen Modellserie: ISO-Drehwendeschneidplatten FAQ Welche Werkstoffe sind für die VCMT160404 AH8005 besonders geeignet? Die VCMT160404 AH8005 von Tungaloy ist speziell für hitzebeständige Legierungen und harte Werkstoffe entwickelt und liefert bei stabiler Bearbeitung gute Standzeiten und kontrollierte Spanbildung. Welcher Freiwinkel ist bei der Platte auszuführen? Die Platte hat einen Freiwinkel von 7°; dieser Wert ist bei der Auswahl des passenden ISO-Drehhalters zu berücksichtigen, um optimale Schneidbedingungen zu erreichen. Wie beeinflusst die PVD-Beschichtung die Standzeit? Die PVD-Beschichtung der AH8005 sorgt für eine harte, verschleißfeste Schicht an der Schneidkante, was die Standzeit erhöht und die Widerstandsfähigkeit gegenüber thermischer Beanspruchung verbessert. Ist die Platte auch für Innenbearbeitung geeignet? Ja, die ISO-Geometrie und die kompakte rhombische Form erlauben sowohl Außen- als auch Innendrehen, vorausgesetzt, Halter und Einspannmaß sind kompatibel. Welche Merkmale machen diese Wendeschneidplatte wirtschaftlich? Die Kombination aus stabiler Spanbildung, hoher Verschleißfestigkeit und ISO-Kompatibilität reduziert Werkzeugwechsel und sorgt für planbare Prozesskosten in Serienfertigung. Hersteller: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenzeichen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers.
VCMT 160404 AH8005 Wendeplatten - Tungaloy
VCMT 160404 AH8005 Wendeschneidplatte für Drehen von Tungaloy Die VCMT 160404 AH8005 ist eine ISO-genormte Wendeschneidplatte für das Außen- und Innendrehen, ausgelegt auf stabile Bearbeitung harter und hitzebeständiger Werkstoffe. ISO-genormt für universelle Halterkompatibilität PVD-beschichtetes Hartmetall für lange Standzeit Optimierter Spanbrecher PS für stabile Spanbildung Rhombische Form 16 mm mit 0,4 mm Eckenradius Mit Loch und zylindrischer Senkung 40°–60° Leistungsstarke Beschichtung für anspruchsvolle Werkstoffe Die PVD-beschichtung in Kombination mit Hartmetall sorgt für hohe Verschleißfestigkeit bei höheren Schnittgeschwindigkeiten. Dies führt zu konstanter Schneidkantenstabilität und längeren Werkzeugstandzeiten bei der Bearbeitung hitzebeständiger Legierungen. Ein klarer Nutzen ist die reduzierte Stillstandszeit in Fertigungsprozessen, weil weniger Wechselzyklen erforderlich werden. Präzise Form und Passgenauigkeit sichern Prozessstabilität Die rhombische Plattenform mit Eckenradius 0,4 mm und einem Freiwinkel von 7° gewährleistet eine zuverlässige Spanabfuhr und einfache Halteranpassung. Außerdem unterstützt das zylindrische Loch mit einseitiger Senkung die formschlüssige Montage und minimiert Vibrationen. Daraus ergibt sich ein Vorteil: gleichbleibende Oberflächengüte bei seriennaher Produktion. Konkrete Anwendung und Materialabdeckung Entwickelt für das Drehen von harten Werkstoffen und hitzebeständigen Legierungen, bietet diese Sorte AH8005 eine breite Werkstoffabdeckung. Für Anwender in der Serienfertigung bedeutet das weniger Werkzeugvarianten auf Lager und mehr Prozesssicherheit bei wechselnden Schrupp- und Schlichtaufgaben. Die Auswahl des Spanbrechers PS optimiert dabei die Spanform für stabile Schnittbedingungen. Integration in Werkzeugkreise und Ersatzteilmanagement Im Systemaufbau fungiert die Wendeschneidplatte zusammen mit passenden Außenhaltern, Unterlagen und Befestigungselementen. Die normierte Bauform erleichtert die Beschaffung von Ersatzplatten und reduziert Administrationsaufwand. Für Betriebe ergibt sich daraus ein praktischer Vorteil: schnelle Verfügbarkeit und einfache Logistik in der Werkzeugversorgung. Empfehlung: Für produktive Zerspanung die VCMT 160404 AH8005 von Tungaloy wählen – Bestellanfrage und technische Beratung: info@metav-werkzeuge.com, +49 2822 7131930 Produktmerkmale Artikelnummer: 6747798 Marke: Tungaloy Serie: ISO-Drehwendeschneidplatten Bezeichnung: VCMT160404-PS AH8005 Hersteller SKU: TUN6747798 Fakten Eckenradius: 0,4 mm Freiwinkel: 7° Winkel: 35° Plattendicke: 4,76 mm Plattengröße: 16 mm Besonderheiten Material: Hartmetall Beschichtung: PVD-beschichtung Sorte: AH8005 — verschleißfest für hitzebeständige Legierungen Spanbrecher: PS — optimierter Spanformer für stabile Spanbildung Plattenform: rhombisch Loch: mit Loch Lochstil: zylindrisches Loch + einseitige Senkung (40°–60°) Modellserie: ISO-Drehwendeschneidplatten FAQ Wie unterscheidet sich die AH8005-Sorte von anderen Hartmetallsorten? Die AH8005-Sorte ist PVD-beschichtet und auf hohe Verschleißfestigkeit bei hitzebeständigen Legierungen ausgelegt. Die VCMT 160404 AH8005 Wendeschneidplatte von Tungaloy bietet dadurch längere Standzeiten und stabile Schneidkanten im Vergleich zu unbeschichteten Sorten. Für welche Bearbeitungsarten eignet sich die VCMT160404-PS am besten? Die VCMT160404-PS AH8005 ist primär für Außen- und Innendrehen konzipiert; der Spanbrecher PS ist auf stabile Spanbildung ausgelegt und eignet sich besonders für serielle Schrupp- und Schlichtoperationen an harten Werkstoffen. Welche Halter sind kompatibel mit dieser ISO-Bezeichnung? Halter, die ISO-genormte VCMT-Platten aufnehmen, sind kompatibel; die Montage hängt von Form, Freiwinkel, Befestigung und Plattendicke ab. Bei Unsicherheit empfiehlt sich der Abgleich der Halter-Spezifikation mit der VCMT 160404 AH8005 Plattengeometrie. Wie beeinflusst der Eckenradius 0,4 mm die Bearbeitungsergebnisse? Ein Eckenradius von 0,4 mm reduziert die Schnittkraftspitzen und unterstützt eine bessere Oberflächengüte bei Schlichtoperationen. Die VCMT 160404 AH8005 liefert dadurch gleichmäßigere Ergebnisse bei feineren Schnitten. Ist die VCMT 160404 AH8005 für die Bearbeitung von Aluminium geeignet? Obwohl die Sorte AH8005 für hitzebeständige Legierungen optimiert ist, kann die VCMT 160404-PS prinzipiell auch bei anderen Werkstoffen eingesetzt werden; für reines Aluminium sind jedoch speziell ausgelegte Sorten oft vorteilhafter. Hersteller: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenzeichen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers.
VCMT 160404 AH8005 Wendeplatten - Tungaloy
Take advantage of a wear‑resistant PVD‑coated cemented carbide grade and precise geometry to maintain production stability and surface quality in turning operations; order directly via Metav Werkzeuge or consult our specialists for application support. VCMT 160404 AH8005 – Turning insert, PVD‑coated cemented carbide, 35° (Tungaloy) A VCMT 160404 AH8005 ISO rhombic insert for general turning, optimised for stable machining of heat‑resistant alloys and other hard materials VCMT 160404 AH8005 rhombic insert PVD‑coated 35° lead angle for versatile turning 0.4 mm corner radius for fine profiling Cylindrical hole with 40°–60° countersink Stable cutting performance for demanding turning tasks The insert delivers consistent results in external and internal turning thanks to its PVD‑coated cemented carbide substrate and defined geometry. The combination of a 35° lead angle and a 0.4 mm corner radius produces reliable contact conditions that reduce vibration and support repeatable cutting forces. For facilities running mixed batches or tough alloys, this leads to higher first‑pass quality and fewer rework operations, improving overall throughput and process stability. Material and coating that extend tool life The cutting grade AH8005 is a wear‑resistant PVD coating applied to a carbide substrate, selected for machining heat‑resistant alloys and other hard materials under stable conditions. The PVD layer improves thermal and abrasive resistance, which means longer edge life when compared with uncoated grades in similar applications. Explaining PVD simply: a thin, hard coating is deposited to protect the carbide core from heat and abrasive wear, yielding better economy per edge in serial production. Compatibility and system advantages for workshop integration Dimensionally the insert matches ISO standards and is compatible with standard clamping systems when the holder form, relief angle, tolerance class, fastening method, size and thickness are aligned. The plate thickness of 4.76 mm, nominal size 16 mm, and the rhombic configuration make it easy to integrate into established toolholders or boring bars. The insert is supplied as part of a system concept that includes the ISO insert, a suitable external holder or boring bar, a shim/locking set and replacement screws so that set‑up time is predictable and inventory manageable. Chip control and application guidance for reliable results This grade is paired with the PSS chipbreaker, developed for effective chip formation in the intended materials and cutting conditions. Selecting the correct chipbreaker and cemented carbide grade reduces the risk of built‑up edge, improves surface finish and simplifies post‑process handling. For best results, match feed and speed to the workpiece and the rigidity of the set‑up; stable cutting conditions will exploit the AH8005 advantages and preserve the cutting edge for extended running times. Discuss the Tungaloy AH8005 insert with Metav Werkzeuge to confirm suitability for specific turning tasks; contact info@metav-werkzeuge.com or call +49 2822 7131930 for precise application advice and ordering assistance Technical data Article number: 6747794 SKU: 6747794-Tungaloy Manufacturer SKU: TUN6747794 Model series: ISO turning indexable insert series Designation: VCMT160404-PSS AH8005 Brand: Tungaloy Facts Lead angle: 35° Corner radius: 0.4 mm Thickness: 4.76 mm Size: 16 mm Hole: cylindrical hole + one‑side countersink (40°–60°) Special features Material: cemented carbide Coating: PVD‑coated Grade: AH8005 Chipbreaker: PSS Shape: rhombic Application: turning System composition: ISO insert, holder or boring bar, shim/locking set, replacement screws Compatibility: ISO‑standard dimensions and clamping FAQ What materials is this insert designed to machine? The VCMT 160404 AH8005 insert is intended for machining heat‑resistant alloys and other hard materials under stable conditions; the AH8005 grade and PVD coating enhance wear resistance in such work. How does the AH8005 grade differ from standard grades? AH8005 is a wear‑resistant, PVD‑coated cemented carbide grade engineered for elevated temperatures and abrasive conditions, offering longer tool life and consistent edge security compared with uncoated or general‑purpose grades. Will this insert fit existing holders? Compatibility is determined by form, relief angle, tolerance class, fastening, size and thickness; the VCMT 160404 conforms to ISO dimensions and will fit holders that match those parameters. What are the key dimensional specifications to check? Key values: lead angle 35°, corner radius 0.4 mm, thickness 4.76 mm, nominal size 16 mm, and the hole style (cylindrical with 40°–60° countersink). Which chipbreaker should be chosen for mixed material batches? The PSS chipbreaker supplied on VCMT160404‑PSS is optimised for the stated material range; chipbreaker selection should consider material, cutting mode and stability to ensure controlled chip formation. Manufacturer/Responsible: Tungaloy‑NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand‑new product from the manufacturer.
VCMT 160404 AH8005 Wendeplatten - Tungaloy
Take advantage of the wear-resistant PVD-coated AH8005 grade and the PSF chipbreaker for stable, efficient turning of heat-resistant alloys and hard materials; the rhombic ISO geometry with a 0.4 mm corner radius and standard mounting hole ensures straightforward integration into ISO holders. Order directly via Metav Werkzeuge or consult their specialists for process-matched selection and delivery. VCMT 160404 AH8005 — ISO turning insert for stable machining by Tungaloy, PVD‑coated carbide, PSF chipbreaker VCMT160404-PSF AH8005 is an ISO rhombic turning insert designed for external and internal turning of demanding materials where wear resistance and stable cutting behaviour are required PVD-coated carbide for high wear resistance PSF chipbreaker for controlled chip formation 0.4 mm corner radius for edge strength ISO compatibility for standard holders Consistent metal removal with extended tool life The PVD-coated carbide grade AH8005 combines wear resistance with thermal stability to deliver longer tool life in machining heat‑resistant alloys and harder workpieces. The PSF chipbreaker is optimised for controlled chip formation under stable cutting conditions, reducing the risk of built-up edge and improving surface consistency. Specified geometry and coating chemistry mean fewer interruptions for tool changes, which increases productivity and lowers cost per component in medium‑ to high‑volume turning operations. Precision geometry for repeatable results and flexible use With the ISO VCMT160404 designation and a rhombic form, the insert provides a predictable cutting face and reproducible contact conditions when mounted in compatible holders. The combination of a 0.4 mm corner radius and 4.76 mm plate thickness gives mechanical robustness while maintaining the ability to produce defined contours. The 35° lead angle and 7° clearance angle contribute to stable cutting forces and predictable chip flow, making this insert suitable for both finishing and light roughing passes where surface quality and dimensional accuracy matter. Easy integration and informed process selection The insert is supplied with a cylindrical hole with single‑sided countersink (40°–60°) to match common clamping systems; compatibility depends on form, clearance angle, tolerance class, fastening and size. Specification as an ISO turning indexable insert simplifies tool management across multiple machines and fixtures. Selection of the correct grade and chipbreaker—here AH8005 with PSF—should be based on workpiece material and machine stability to achieve optimal cycle times and predictable tool life. For applications with varying rigidity or material mix, the grade’s broad coverage supports rapid process adjustment. For application advice on the Tungaloy VCMT160404-PSF AH8005 and to arrange supply through Metav Werkzeuge, contact info@metav-werkzeuge.com or call +49 2822 7131930 for prompt, application‑oriented support Technical data Article number: 6747790 Manufacturer SKU: TUN6747790 SKU: 6747790-Tungaloy Label: VCMT160404-PSF AH8005 Facts Corner radius: 0.4 mm Plate thickness: 4.76 mm Inscribed circle / size: 16 mm ISO code: 160404 Lead angle: 35° Clearance angle: 7° Hole style: cylindrical hole + single-sided countersink (40°–60°) Special features Material: carbide Coating: PVD Grade: AH8005 Chipbreaker: PSF Shape: rhombic Application: turning Model series: ISO turning indexable inserts Compatibility: determined by form, clearance angle, tolerance class, fastening, size and thickness FAQ What materials is this insert suitable for? The insert in grade AH8005 is intended for wear‑resistant performance on heat‑resistant alloys and harder materials; the specification supports a broad material range under stable cutting conditions. How does the PSF chipbreaker affect machining? The PSF chipbreaker promotes controlled chip formation and evacuation, improving process stability and surface finish when the grade AH8005 and the insert geometry are matched to the cutting parameters. Can the insert be used in standard ISO toolholders? Yes, the VCMT160404-PSF follows ISO geometry; compatibility depends on holder form, clearance, tolerance class, fastening and the insert’s size and thickness. Is this insert suitable for finishing operations? The combination of a 0.4 mm corner radius, robust plate thickness and the PVD coating makes this insert suitable for precise finishing passes where edge strength and consistent surface quality are required. Which element identifies the article for reordering? Use the article number 6747790 or the manufacturer SKU TUN6747790 when reordering the specific Tungaloy insert. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
VCMT 160404 AH8015 Wendeplatten - Tungaloy
The combination of a PVD-coated carbide grade (AH8015) and a precise rhombic geometry delivers a balanced mix of wear resistance and cutting-edge stability for reliable turning performance; order the insert directly via Metav Werkzeuge or consult the team for application-specific advice. VCMT160404-PS AH8015 — ISO turning insert, PVD-coated carbide, rhombic, for turning by Tungaloy The VCMT160404-PS AH8015 is a rhombic ISO turning insert designed for external and internal turning of heat-resistant alloys, offering a balance between edge stability and wear resistance for general-purpose machining. PVD-coated carbide grade AH8015 Rhombic shape with 7° relief angle 0.4 mm corner radius Compatible with ISO turning holders Longer tool life through balanced coating and substrate The VCMT160404-PS AH8015 uses a PVD-coated carbide substrate engineered to combine wear resistance with edge stability. The PVD process produces a hard, thin coating that reduces abrasive wear while maintaining a sharp cutting edge; this balance means longer intervals between indexings and fewer unscheduled tool changes. For shops machining heat-resistant alloys, the grade offers a practical compromise: sufficient resistance to elevated temperatures and steady performance under varying cutting conditions. The result is a measurable improvement in component consistency and lower tooling-related downtime. Accurate geometry for consistent surface finish and chip control The insert’s rhombic form and 7° relief angle contribute to predictable engagement with the workpiece, while the 0.4 mm corner radius helps produce a controlled profile at the cutting edge. The PS chipbreaker is designed to fragment and evacuate chips effectively in typical turning operations, improving process stability on both external and internal passes. Compatibility with ISO toolholders is governed by form, relief, tolerance class, fastening and thickness; selecting the correct holder and clamp ensures repeatable seat and torque, which directly benefits surface quality and dimensional repeatability. Process efficiency and reduced cycle interruptions A combination of grade selection and chip management supports higher productivity: the coating reduces flank wear, and the chipbreaker minimises entanglement and rework. The result is a lower cost per component through extended edge life and fewer stoppages. Where stability allows, the insert enables slightly higher cutting parameters compared with uncoated alternatives, contributing to shorter machining times without compromising finish. For batch production or mixed-series work, the insert’s balanced characteristics make it a dependable option for stable, repeatable turning cycles. Practical system assembly and application notes The insert is part of an ISO system comprising the insert, a matching external holder or boring bar, shim/clamp sets and replacement screws. The insert is supplied with a cylindrical hole and a one-sided countersink (40°–60°) for secure fastening. Selection of chipbreaker and grade should align with workpiece material, machining method and machine stability; the design supports both roughing and light finishing when combined with an appropriate toolholder. For first-time integration, verify form, free angle, tolerance class, fastening method, size and thickness to ensure correct seating and torque. Contact Metav Werkzeuge for availability and tailored technical advice on Tungaloy VCMT160404-PS AH8015 inserts for high-temperature alloy turning Technical Data Article number: 6747799 Manufacturer SKU: TUN6747799 Retail SKU: 6747799-Tungaloy Designation: VCMT160404-PS AH8015 Facts Size: 16 mm Thickness: 4.76 mm Relief angle: 7° Corner radius: 0.4 mm Hole style: cylindrical hole with one-sided countersink (40°–60°) Insert angle: 35° Special features PVD-coated carbide grade AH8015 PS chipbreaker Rhombic insert shape For turning (external and internal) Compatible with ISO turning holders (form, free angle, tolerance, fastening, size, thickness) System components: insert, holder/boring bar, shim/clamp set and replacement screws FAQ Which materials are best suited to this insert? The Tungaloy VCMT160404-PS AH8015 is specified as a first choice for general machining of heat-resistant alloys, offering a compromise between wear resistance and edge stability suitable for many alloyed materials. What is the purpose of the PS chipbreaker? The PS chipbreaker on this insert controls chip formation and evacuation during turning, reducing the risk of built-up edge and facilitating stable, continuous cuts for consistent surface finish. What are the key dimensions and mounting details? This insert is 16 mm across, 4.76 mm thick, with a 0.4 mm corner radius and a cylindrical hole with a one-sided countersink (40°–60°) for secure fastening in ISO-compatible holders. How does the PVD coating affect performance? The PVD coating on the AH8015 grade enhances abrasive wear resistance while maintaining a sharp cutting edge, which extends tool life and supports higher process reliability under elevated temperatures. How to ensure correct holder compatibility? Compatibility is determined by insert form, free angle, tolerance class, fastening, size and thickness; matching these parameters with a suitable ISO turning holder or boring bar ensures correct seating and repeatable cutting performance. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
VCMT 160404 AH8015 Wendeplatten - Tungaloy
Take advantage of a balanced combination of wear resistance and edge stability for reliable turning of heat‑resistant alloys; the PVD‑coated carbide grade AH8015 and the TSF chipbreaker ensure controlled chips and consistent surface quality. Order directly via Metav Werkzeuge or consult our technical team for application guidance. VCMT160404-TSF AH8015 — ISO rhombic turning insert for external and internal turning by Tungaloy The VCMT160404-TSF AH8015 is an ISO‑standard rhombic insert designed for turning operations, optimised for heat‑resistant alloys and general machining where a balance of wear resistance and edge stability is required PVD-coated carbide AH8015 ISO rhombic insert, size 160404 0.4 mm corner radius, 7° clearance Cylindrical hole with 40°–60° countersink Consistent performance on heat‑resistant alloys The VCMT160404-TSF AH8015 is built on a PVD coating applied to a carbide substrate, providing a measured compromise between wear resistance and edge stability. This combination reduces flank wear and thermal softening when machining difficult, heat‑resistant materials, so fewer insert changes are required and part tolerances remain stable. The chipbreaker TSF promotes segmented or short chips in turning, which lowers the risk of entanglement and reduces rework. For production environments seeking predictable tool life and repeatable surface finish, this insert offers a technically straightforward path to improved process reliability without complex parameter tuning. Reliable fit and straightforward setup for reduced downtime Conforming to ISO‑standard dimensions, the rhombic geometry and defined mounting details make holder selection and insert exchange uncomplicated. The insert’s 35° lead angle and 7° clearance ensure a familiar cutting geometry for many external and internal turning holders, while the 0.4 mm corner radius supports fine surface definition on transitional passes. The plate is 16 mm in nominal size with a 4.76 mm thickness, and the cylindrical hole with a 40°–60° countersink simplifies clamping and alignment in compatible toolholders. These measurable specifications translate into shorter setup times, fewer fitting errors and consistent clamping force across tool changes. Efficient chip control and economic machining Designed for productive machining, the insert’s chip control characteristics reduce handling and disposal effort while supporting higher feed rates where machine and workholding rigidity allow. The alloy‑oriented grade delivers extended tool life through a stable cutting edge and predictable wear progression, which enhances overall machining economics by lowering insert consumption per part produced. As a component of an ISO‑based system — insert, matched external holder or boring bar, shim/clamping set and spare screws — the plate integrates into established tooling stocks and maintenance routines, enabling fast replacement and minimal interruption to production. For tailored recommendations on Tungaloy carbide inserts and to confirm suitability for specific turning tasks, contact Metav Werkzeuge for technical advice at info@metav-werkzeuge.com or call +49 2822 7131930 Technical Data Article number: 6825779 SKU: 6825779-Tungaloy Manufacturer SKU: TUN6825779 Model series: ISO-Drehwendeschneidplatten Designation: VCMT160404-TSF AH8015 Core data Size: 16 mm Thickness: 4.76 mm Corner radius: 0.4 mm Clearance angle: 7° Lead/approach angle: 35° Hole: with hole Hole style: cylindrical hole + single-sided countersink (40°–60°) Special features Material: carbide Coating: PVD Grade: AH8015 Chipbreaker: TSF Plate shape: rhombic Application: turning (external and internal) System components: ISO insert, matching outer holder or boring bar, shim/clamping set, spare screws FAQ Is this insert suitable for machining heat‑resistant alloys? The VCMT160404-TSF AH8015 is intended as a first choice for general machining of heat‑resistant alloys thanks to its PVD coating and balanced carbide composition. Which holders are compatible with this ISO plate? Compatibility depends on holder form, clearance angle, tolerance class, clamping method, size and thickness; use holders specified for ISO 160404 rhombic inserts and the appropriate clamping set. What chip form can be expected with the TSF chipbreaker? The TSF chipbreaker on this turning insert promotes controlled, short or segmented chips during turning, improving swarf handling and surface quality. Can this insert be used for internal turning operations? Yes; the rhombic geometry and ISO dimensions permit use in both external and internal turning holders when mounted with the correct boring bar or holder. What components are needed to complete a tooling system with this plate? A complete system typically includes the ISO insert, a matched external holder or boring bar, a shim/clamping set and suitable replacement screws for secure mounting. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
VCMT 160404 AH8015 Wendeplatten - Tungaloy
VCMT 160404 AH8015 ISO-Drehwendeschneidplatte für Drehen | Tungaloy Die VCMT 160404 AH8015 ist eine PVD-beschichtete Hartmetall-Wendeplatte für das Außen- und Innendrehen hitzebeständiger Legierungen und vereint Verschleißfestigkeit mit stabiler Schneidkante. PVD-beschichtetes Hartmetall AH8015 Optimierter einseitiger Spanbrecher Rhombische Form 16 mm Zylindrisches Loch mit Senkung 40°–60° Hocheffiziente Schnittleistung für hitzebeständige Legierungen Die AH8015-Sorte wurde als ausbalancierte Lösung für die allgemeine Bearbeitung hitzebeständiger Legierungen entwickelt. Dank der PVD-Beschichtung erhöht sich die Verschleißfestigkeit, während die Schneidkantenstabilität erhalten bleibt. Das Ergebnis ist eine konstante Schnittqualität bei anspruchsvollen Werkstoffen, wodurch Standzeiten verlängert und Stillstandszeiten reduziert werden. Anwender profitieren von reproduzierbaren Ergebnissen bei Serienfertigung und Lohnbearbeitung. ISO-Genauigkeit für einfache Halterkompatibilität Die ISO-Genormung sichert die Passform zu gängigen Außenhaltern und Bohrstangen; entscheidend sind dabei Form, Freiwinkel und Plattendicke. Mit Freiwinkel 7°, Plattendicke 4,76 mm und Plattengröße 16 mm lässt sich die Platte schnell und sicher in standardisierte Systeme einfügen. Diese Präzision vereinfacht den Werkzeugwechsel und minimiert Einrichtzeiten, was besonders in Mehrschichtbetrieb und bei kurzen Losgrößen wirtschaftlich wirkt. Geeignet für Produktionsbetriebe: geringere Kosten pro Bauteil Die rhombische Form mit Eckenradius 0,4 mm ermöglicht flexible Schneidbedingungen beim Außen- und Innendrehen. Der einseitige Spanbrecher fördert kontrollierte Spanbildung und verbessert Oberflächengüte bei stabilen Bearbeitungsparametern. Fertigungsbetriebe und Lohnbearbeiter erreichen so bessere Taktzeiten und planbare Werkzeugkosten, weil die Kombination aus stabiler Schneide und Verschleißschutz Ausfallrisiken senkt. Für präzise und wirtschaftliche Zerspanung empfiehlt sich die VCMT 160404 AH8015 von Tungaloy; technische Beratung und direkte Beschaffung über Metav Werkzeuge unter info@metav-werkzeuge.com oder +49 2822 7131930 Produktmerkmale Artikelnummer: 6747803 Hersteller: Tungaloy Bezeichnung: VCMT160404 AH8015 Modellserie: ISO-Drehwendeschneidplatten SKU: 6747803-Tungaloy Hersteller SKU: TUN6747803 Fakten Eckenradius: 0,4 mm Plattendicke: 4,76 mm Plattengröße: 16 mm Winkel: 35° Freiwinkel: 7° Besonderheiten Material: Hartmetall Schneidstofftyp: PVD-beschichtetes Hartmetall Sorte: AH8015 (für hitzebeständige Legierungen) Plattenform: Rhombisch Loch: mit Loch Lochstil: zylindrisches Loch + einseitige Senkung (40°–60°) Spanbrecher: einseitig Anwendung: Drehen Typische Anwendung: Außen- und Innendrehen FAQ Welche Werkstoffe bearbeitet die VCMT 160404 AH8015 am besten? Die VCMT 160404 AH8015 von Tungaloy ist speziell für hitzebeständige Legierungen ausgelegt, zeigt aber auch gute Performance bei anderen schwer zerspanbaren Werkstoffen dank der PVD-beschichtung und ausgewogenen Schneidstoffzusammensetzung. Wie beeinflusst der Eckenradius die Bearbeitung? Der Eckenradius 0,4 mm ermöglicht feine Konturen und eine gute Oberflächengüte; bei Bedarf kann durch Radiuswahl das Bauteilverhalten in Bezug auf Kantenausbildung und Bauteilspannung optimiert werden. Welche Halter passen zur Platte? ISO-genormte Außenhalter und Bohrstangen, die Form, Freiwinkel und Plattendicke unterstützen, sind kompatibel. Die Angaben Freiwinkel 7° und Plattendicke 4,76 mm dienen als Auswahlkriterium für geeignete Halter. Ist die Platte für Serienfertigung geeignet? Ja, die VCMT 160404 AH8015 ist für produktive Zerspanung ausgelegt und bietet durch hohe Verschleißfestigkeit und stabile Schneidkante planbare Standzeiten, was sie für Serienfertigung und Lohnbearbeitung attraktiv macht. Hersteller: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenzeichen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers.
VCMT 160404 AH8015 Wendeplatten - Tungaloy
VCMT 160404 AH8015 – ISO-Drehwendeschneidplatte für Drehen (Tungaloy) Die VCMT 160404 AH8015 ist eine ISO-genormte, PVD-beschichtete Hartmetall-Wendeplatte für Außen- und Innendrehen hitzebeständiger Legierungen PVD-beschichtetes Hartmetall für hohe Standzeit Rhombische Plattenform, 16 mm Plattengröße Eckenradius 0,4 mm für feine Konturen Mit zylindrischem Loch und Senkung 40°–60° Spanbrecher PSF für stabile Spanbildung Haltbarkeit und Schneidkantenstabilität für produktive Bearbeitung Die VCMT160404-PSF AH8015 kombiniert PVD-beschichtung und robusten Hartmetall-Schneidstoff, um Verschleiß und Aufkantenbildung bei hohen Temperaturen zu reduzieren. Die Beschichtung bietet eine ausgewogene Balance zwischen Verschleißfestigkeit und Schneidkantenstabilität, sodass längere Spanfolgen und stabilere Schnittbedingungen möglich sind. Das Ergebnis ist eine konstantere Fertigungsqualität bei anspruchsvollen Legierungen. Geeignet für hitzebeständige Legierungen und vielseitige Einsätze Durch die Materialauslegung und den Spanbrecher PSF eignet sich die Platte besonders für das Drehen von hitzebeständigen Legierungen. Anwender profitieren von guter Spanformung und reduziertem Nachbearbeitungsaufwand. Die Kombination aus Eckenradius 0,4 mm und präziser Plattengeometrie ermöglicht exakte Konturschnitte und feine Oberflächen an Innen- und Außenkonturen. Systemkompatibilität und sichere Montage Die ISO-Genormtheit gewährleistet hohe Kompatibilität mit gängigen Haltern; entscheidend sind Form, Freiwinkel, Toleranzklasse und Plattendicke. Die Platte kommt mit Loch und einer zylindrischen Lochform mit einseitiger Senkung (40°–60°), was die Befestigungssicherheit erhöht und die Montage vereinfacht. Die Plattendicke von 4,76 mm trägt zur Stabilität bei, besonders bei längeren Überständen. Wirtschaftlichkeit, Prozesssicherheit und Einsatzeffizienz Mit Fokus auf lange Standzeiten und zuverlässige Spanabfuhr verbessert diese Wendeplatte die Maschinenauslastung und senkt Stillstandszeiten. Die Kombination aus stabiler Schneidkante und optimiertem Spanformer führt zu reproduzierbaren Ergebnissen und reduziert Ausschuss. Für Fertigungsumgebungen mit hohem Durchsatz ist die Platte eine wirtschaftliche Wahl, die konstante Bearbeitungsqualität liefert. Für präzise und wirtschaftliche Drehprozesse empfehlen wir die VCMT 160404 AH8015 von Tungaloy; bei Fragen zur passenden Halterkombination oder zur Prozessoptimierung erreichen Sie unsere technische Beratung per eMail info@metav-werkzeuge.com oder telefonisch unter +49 2822 7131930. Produktmerkmale Artikelnummer: 6747791 Marke: Tungaloy Serie: ISO-Drehwendeschneidplatten Bezeichnung: VCMT160404-PSF AH8015 Hersteller SKU: TUN6747791 Fakten Eckenradius: 0,4 mm Winkel: 35° Freiwinkel: 7° Plattendicke: 4,76 mm Plattengröße: 16 mm Besonderheiten Material: Hartmetall Beschichtung: PVD-beschichtet (Dünnschichtverfahren, verschleißoptimiert) Sorte: AH8015 (ausgewogen für hitzebeständige Legierungen) Plattenform: rhombisch Loch: mit Loch Lochstil: zylindrisches Loch + einseitige Senkung (40°–60°) Spanbrecher: PSF Anwendung: Drehen Modellserie: ISO-Drehwendeschneidplatten FAQ Welche Werkstoffe lassen sich mit der Platte bearbeiten? Die VCMT160404-PSF AH8015 von Tungaloy ist speziell für hitzebeständige Legierungen ausgelegt; sie bietet aber auch gute Performance bei verschiedenen Stahl- und Legierungsgruppen dank der verschleißfesten PVD-Beschichtung. Welchen Vorteil bringt der Spanbrecher PSF? Der Spanbrecher PSF sorgt für kontrollierte Spanformung und stabile Spanabfuhr, was die Standzeit erhöht und Oberflächenqualität während des Drehens verbessert. Welche Bedeutung hat der Eckenradius 0,4 mm? Ein Eckenradius von 0,4 mm ermöglicht feine Konturenschnitte und bessere Detailgenauigkeit, ideal bei präzisen Außen- und Innenbearbeitungen. Ist die Platte mit gängigen Haltern kompatibel? Ja, die Platte ist ISO-genormt; Kompatibilität hängt von Form, Freiwinkel, Toleranzklasse und Befestigungsart des Halters ab. Die mitgelieferte Loch- und Senkungsgeometrie erhöht die Montageflexibilität. Wie trägt die PVD-Beschichtung zur Produktivität bei? Die PVD-Beschichtung reduziert Reibung und Verschleiß, stabilisiert die Schneidkante bei höheren Temperaturen und verlängert dadurch die effektive Standzeit in kontinuierlichen Fertigungsprozessen. Hersteller: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenzeichen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers.
VCMT 160404 AH8015 Wendeplatten - Tungaloy
Take advantage of the balanced combination of PVD‑coated carbide wear resistance and the TM chipbreaker for predictable chip control; the ISO format and standard dimensions ensure reliable fitment in common holders. Order the VCMT160404‑TM AH8015 inserts directly via Metav Werkzeuge or consult our specialists for process optimisation. VCMT 160404 AH8015 — ISO VCMT turning insert for general turning (Tungaloy) VCMT160404‑TM AH8015 is an ISO‑format indexable turning insert optimised for general external and internal turning, designed to machine heat‑resistant alloys with a balanced combination of wear resistance and edge stability. PVD‑coated carbide AH8015 for heat‑resistant alloys TM chipbreaker for controlled chip formation ISO format VCMT 160404 for standard toolholders Cylindrical hole with 40°–60° countersink Consistent cutting performance for difficult alloys The PVD‑coated carbide substrate in this grade delivers a durable cutting edge that is particularly suited to machining heat‑resistant alloys. The chosen microstructure of the AH8015 grade offers a compromise between wear resistance and edge toughness, which translates into longer intervals between indexings and a more predictable tool life. For routine and mixed‑batch turning operations, this balance reduces unplanned stops and supports steady production rates. Predictable fit and repeatability in ISO tooling systems As an ISO‑format rhombic insert with a 16 mm cutting‑edge length and a plate thickness of 4.76 mm, the insert is designed for straightforward integration into standard VCMT holders. Key geometric values such as the 0.4 mm corner radius, 7° clearance, and the primary 35° orientation ensure repeatable seating and cutting geometry when the holder, shim and clamp match the ISO parameters. The cylindrical hole with 40°–60° countersink provides secure clamping and reliable repeatability for both internal and external turning setups. Improved process reliability through chip control and system design The TM chipbreaker is engineered to produce short, controllable chips across a range of feeds and depths of cut, improving swarf evacuation and reducing the likelihood of built‑up edge. In practice, pairing this insert with a suitable holder, underlay/shim and correct clamping hardware forms a complete system that supports consistent surface finish and dimensional stability. The system approach—insert, holder, shim, clamp and spare screws—reduces setup time and contributes to lower overall cycle times while maintaining machining quality. For application advice, tooling recommendations or to request VCMT160404‑TM AH8015 inserts contact Metav Werkzeuge GmbH at info@metav-werkzeuge.com or call +49 2822 7131930 for direct technical consultation and supply options. Technical data Article number: 6825803 Manufacturer SKU: TUN6825803 Our SKU: 6825803‑Tungaloy Designation: VCMT160404‑TM AH8015 Model series: ISO indexable turning inserts Material: Carbide (PVD‑coated) Application: Turning Core dimensions and measurable data Cutting edge size: 16 mm Plate thickness: 4.76 mm Corner radius: 0.4 mm Clearance angle: 7° Main angle: 35° ISO code: 160404 Countersink angle: 40°–60° Special features and versions TM chipbreaker for controlled chips PVD coating, grade AH8015 Rhombic plate form (VCMT) With cylindrical hole and one‑sided countersink ISO‑standard format for compatibility with common holders FAQ What materials are suitable for this insert? The VCMT160404‑TM AH8015 insert (Tungaloy indexable turning insert, SKU TUN6825803 / 6825803‑Tungaloy) is primarily intended for machining heat‑resistant alloys and offers a balance between wear resistance and edge stability for general turning work. Which toolholders are compatible with this format? Compatibility is determined by form, clearance, tolerance class, fastening, size and thickness; the VCMT 160404 format is compatible with standard VCMT holders that accept ISO‑designated rhombic inserts. Which dimensions should be checked before procurement? Verify the plate size (16 mm), plate thickness (4.76 mm), corner radius (0.4 mm), clearance angle (7°) and the ISO code (160404) to ensure correct fit and repeatability. How does the TM chipbreaker affect machining? The TM chipbreaker promotes short, controlled chip formation which aids swarf handling, contributes to a consistent surface finish and lowers the risk of built‑up edge in many turning operations. Is AH8015 a universal grade for turning? AH8015 is a versatile PVD‑coated carbide grade selected as a first choice for general machining of heat‑resistant alloys, offering a practical compromise between tool life and edge stability. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand‑new product from the manufacturer.
VCMT 160404 AH905 Wendeplatten - Tungaloy
VCMT 160404 AH905 Drehwendeschneidplatte für Drehen – Tungaloy Die VCMT 160404 AH905 ist eine ISO-genormte Drehwendeschneidplatte für Außen- und Innendrehen, ausgelegt auf scharfe Schneidkanten und hohe Prozesssicherheit durch PVD-Beschichtung. PVD-beschichtetes Hartmetall, hohe Standzeit Spanformer PS für kontrollierten Spanfluss Rhombische Platte, Plattengröße 16 mm Eckenradius 0,4 mm für feine Schnittkanten Mit Loch und zylindrischer Senkung 40°–60° Produktivität und Prozesssicherheit steigern Die VCMT 160404 AH905 kombiniert eine PVD-Beschichtung mit einem verschleißfesten Hartmetall-Schneidstoff, wodurch die Schnittkante länger stabil bleibt und Ausbrüche reduziert werden. Für Betriebe bedeutet das weniger Stillstand und konstantere Bauteilqualität bei längeren Werkzeugstandzeiten. Die Platte ist für den Einsatz beim Außen- und Innendrehen ausgelegt; die Auswahl des passenden Spanformers PS und der richtigen Haltergeometrie optimiert den Spanfluss und sorgt für reproduzierbare Ergebnisse. Materialverträglichkeit und Schnittbild Die Platte ist so konstruiert, dass sie eine scharfe Schneidkante mit hoher Prozesssicherheit verbindet. Der Spanformer PS ist speziell für kontrollierten Spanbruch ausgelegt und reduziert Rechippen bei instabilen Schnitten. Durch das rhombische Plattenformat und den Eckenradius 0,4 mm lassen sich feine Schnittkanten erzielen, was besonders bei anspruchsvollen Oberflächen wichtig ist. Kunden erhalten damit eine Kombination aus Genauigkeit und Wirtschaftlichkeit. Einbau, Kompatibilität und Handhabung Die Kompatibilität zur Halterung wird durch Form, Freiwinkel 7°, Toleranzklasse, Befestigung, Größe und Dicke bestimmt. Die Systemkonfiguration umfasst ISO-Drehplatte, passenden Außenhalter oder Bohrstange sowie Unterlage, Klemmsatz und Ersatzschrauben. Bei der Montage ist auf korrekte Ausrichtung der Platte und festes Anzugsmoment zu achten, um Vibrationen zu vermeiden und die Standzeit zu maximieren. Hinweise zur Halterauswahl erleichtern die Integration in bestehende Spannsysteme. Zielgruppe und Einsatzempfehlung Diese Wendeschneidplatte richtet sich an Fertigungsbetriebe und CNC-Werkstätten, die Wert auf zuverlässige Bearbeitung und konstante Teilequalität legen. Durch die robuste PVD-Beschichtung eignet sich die Platte sowohl für Serienteile als auch für präzise Einzelteile, wenn scharfe Kanten und Prozessstabilität gefordert sind. Werkstattmeister und Produktionsplaner profitieren von der einfachen Austauschbarkeit im ISO-System und der direkten Einsetzbarkeit in gängigen Haltersystemen. Empfehlen Sie die PVD-beschichtete VCMT 160404 AH905 von Tungaloy für stabile Dreharbeiten und kontaktieren Sie uns bei Fragen per E‑Mail info@metav-werkzeuge.com oder Telefon +49 2822 7131930 Produktmerkmale Artikelnummer: 6879339 Marke: Tungaloy Serie: ISO-Drehwendeschneidplatten Bezeichnung: VCMT160404-PS AH905 SKU: 6879339-Tungaloy Fakten Eckenradius: 0,4 mm Winkel: 35° Freiwinkel: 7° Plattendicke: 4,76 mm Plattengröße: 16 mm Besonderheiten Material: Hartmetall Beschichtung: PVD AH905 Plattenform: rhombisch Loch: mit Loch Lochstil: zylindrisches Loch + einseitige Senkung (40°–60°) Spanbrecher: PS ISO-genormt Einsatz: Außen- und Innendrehen Kompatibilität: Form, Freiwinkel, Toleranzklasse, Befestigung, Größe und Dicke FAQ Welche Anwendung ist für die VCMT 160404 AH905 vorgesehen? Die VCMT 160404 AH905 von Tungaloy ist für das Außen- und Innendrehen konzipiert und bietet durch die PVD-Beschichtung und den Spanformer PS Prozesssicherheit bei drehtechnischen Bearbeitungen. Wie unterscheidet sich die AH905-Beschichtung von einfachen Sorten? Die AH905-Beschichtung auf der VCMT 160404 AH905 sorgt für verschleiß- und ausbruchfeste Schneidkanten, was zu längeren Standzeiten und stabileren Bearbeitungsbedingungen in der Produktion führt. Welche Halter werden für die Montage empfohlen? Für die VCMT160404-PS AH905 sollten Halter gewählt werden, die Form, Winkel und Toleranzklasse der Platte unterstützen; gängige ISO-Außenhalter mit passender Unterlage und Klemmsatz gewährleisten sichere Befestigung. Was bedeutet Spanbrecher PS und warum ist er vorteilhaft? Der Spanbrecher PS ist auf kontrollierten Spanfluss ausgelegt; bei der VCMT 160404 AH905 reduziert er lange zusammenhängende Späne, verbessert die Oberflächengüte und schützt die Schneidkante vor unerwünschten Belastungen. Ist die Platte für Serienfertigung geeignet? Ja, die VCMT 160404 AH905 (SKU 6879339-Tungaloy) ist durch ihre beschichtete Hartmetall-Ausführung und ISO-Normierung besonders für serielle Dreharbeiten geeignet. Hersteller: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenbezeichnungen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers.
VCMT 160404 AT9530 Wendeplatten - Tungaloy
Combining a coated cermet AT9530 grade with a PS chipbreaker and a precise 0.4 mm corner radius results in a turning insert optimised for consistent surface finish and even wear; suitable for finishing and light machining of steel. Order the VCMT 160404 AT9530 directly via Metav Werkzeuge or consult the team for application support if needed. VCMT 160404 AT9530 Coated cermet turning insert, 0.4 mm radius — Tungaloy VCMT 160404 AT9530 is an ISO‑standard rhombic turning insert designed for finishing and light turning operations on steel, offering a combination of surface quality focus and predictable tool life. ISO‑standard rhombic insert Coated cermet grade AT9530 0.4 mm corner radius PS chipbreaker for fine finishing Superior surface quality from a coated cermet grade The coated cermet composition AT9530 provides a significant advantage when the priority is surface finish and uniform wear during light machining. Cermet grades combine ceramic and metallic phases to deliver a harder cutting edge than conventional cemented carbide, which supports finer finishes and improved dimensional stability in finishing passes. With the PS chipbreaker and a 0.4 mm corner radius, the insert is optimised to form short, controlled chips that reduce vibration and minimise rework. This yields a reliable process for shops seeking predictable outcomes in series production or precision one‑off components. ISO compatibility and mounting for reliable machining The insert follows ISO dimensions and geometry, allowing straightforward integration into standard toolholders when matching the insert form, clearance, tolerance class, fastening method, size and thickness. Key specifications such as the 16 mm size, 4.76 mm thickness and rhombic shape ensure consistent seating and clamping in compatible holders. The insert is supplied with a cylindrical hole and a single‑side countersink (40°–60°) to secure fixation and repeatable orientation. A 7° clearance minimises flank contact and reduces rubbing, which contributes to longer life and better surface results when the system is correctly assembled. Operational benefits for turning applications Selected for turning tasks that prioritise finishing, the insert supports both external and internal facing operations where high surface integrity matters. The PS chipbreaker is tailored for light cuts and finishing feeds, producing even chip flow and limiting built‑up edge. The result is fewer interruptions for chip control and less need for secondary machining. From a rational perspective, this translates into improved throughput and reduced scrap rates; from a contact perspective, it offers operators greater confidence in achieving the required surface tolerance across batches. Practical guidance on selection and application When choosing a grade and chipbreaker for a specific steel type and turning process, the combination of AT9530 and PS is aimed at achieving superior finishes with predictable wear behaviour. The small 0.4 mm corner radius is suitable for fine contouring and tight radii where sharp profile definition is required. For users less familiar with grades, think of cermet as a finishing specialist: it excels where fine surface quality and dimensional consistency are priorities, though it is not intended for heavy roughing cuts. Proper holder selection and correct clamping torque are essential to unlock the performance advantages of this ISO‑conforming insert. For precision finishing with Tungaloy’s AT9530 grade, contact Metav Werkzeuge to discuss application suitability, request stock availability or obtain advice at info@metav-werkzeuge.com or +49 2822 7131930 Technical Data Article number: 6773762 Manufacturer SKU: TUN6773762 SKU: 6773762-Tungaloy Model series: ISO‑Drehwendeschneidplatten Core Measurements ISO designation: 160404 Size: 16 Thickness: 4.76 mm Corner radius: 0.4 mm Materials & Features Grade: AT9530 (coated cermet) Chipbreaker: PS Insert form: rhombic Hole: with cylindrical hole + single‑side countersink (40°–60°) Free/clearance angle: 7° Application: turning (finishing and light machining of steel) FAQ What materials is this insert suitable for? The VCMT 160404‑PS AT9530 is optimised for finishing and light machining of steel; the AT9530 coated cermet is focused on surface quality and even wear. What geometry and size does the insert have? This rhombic ISO insert is size 16 with a 4.76 mm thickness, 0.4 mm corner radius and the ISO code 160404 for compatibility with standard holders. How does the PS chipbreaker affect machining? The PS chipbreaker produces short, controlled chips suited to finishing feeds, improving chip control and reducing vibration during fine turning with the AT9530 grade. Can the insert be used for internal turning as well as external? Yes, the insert is suitable for both external and internal turning operations when matched with an appropriate holder and stable setup. How is compatibility with a holder determined? Compatibility depends on insert form, clearance angle (7°), tolerance class, fastening method, size and thickness; matching these parameters ensures correct seating and repeatable performance. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
VCMT 160404 DX120 Wendeplatten - Tungaloy
Take advantage of the combination of PCD cutting performance, extended tool life and ISO compatibility for reliable, high-speed aluminium turning. Order the insert directly via Metav Werkzeuge or consult our technicians for application-specific recommendations. VCMT160404-DIA DX120 — VCMT 160404 DX120 turning insert (PCD) by Tungaloy The VCMT160404-DIA DX120 is an ISO-standard turning insert designed for high-speed aluminium and non-ferrous machining, combining polychrystalline diamond cutting edges with a carbide backing for long, consistent tool life. PCD grade DX120 for high cutting speeds ISO rhombic VCMT 160404 form 0.4 mm corner radius for fine finish Cylindrical hole with 40°–60° countersink High-speed performance for aluminium and non-ferrous alloys The insert’s polykristalliner Diamant (PCD) cutting layer, supplied as DX120, enables significantly higher cutting speeds and exceptional wear resistance when machining aluminium and other non-ferrous materials. The PCD microstructure resists abrasive wear from silicon-rich aluminium alloys and non-metallic abrasives, which translates into fewer tool changes and more stable cycle times in production. For machining operations that prioritise surface quality and repeatability, the hardened diamond cutting edge maintains geometry over long runtimes, reducing the need for frequent regrinding or replacement. Precision geometry and secure clamping for consistent results Designed to the ISO rhombic form, the insert fits common external holders and boring bars when the holder’s form, clearance angle, tolerance class, fastening method, size and thickness are matched. The 0.4 mm corner radius produces a fine finished edge without excessive cutting force, while the cylindrical hole with a single-sided countersink (40°–60°) ensures positive location and reliable clamping in indexable systems. The carbide substrate supports the diamond layer, providing mechanical stability during interrupted cuts and helping to maintain repeatable dimensional accuracy across batches. Productivity gains and economical machining strategy Using a PCD insert such as this grade DX120 often reduces overall machining cost per part through longer tool life and higher feeds and speeds compared with conventional carbide inserts when cutting suitable materials. The combination of diamond wear resistance and a robust backing minimises unplanned downtime and tool-change frequency, which benefits batch production and lights-out machining. Where abrasive, non-metallic inclusions are present, the DX120 grade offers a balance of durability and edge integrity, helping to keep process windows predictable and production throughput high. For application advice on the Tungaloy VCMT160404-DIA DX120 PCD turning insert or to confirm compatibility with existing toolholders, contact Metav Werkzeuge at info@metav-werkzeuge.com or call +49 2822 7131930 for expert recommendations Technical Data Article number: 6822172 Manufacturer SKU: TUN6822172 Model series: ISO-Drehwendeschneidplatten Material: Hartmetall Facts Insert designation: VCMT160404-DIA Grade / sort: DX120 Corner radius: 0.4 mm Insert size: 16 mm Thickness: 4.76 mm Clearance angle: 7° Included hole: yes (cylindrical + single-sided countersink 40°–60°) Angle: 35° Special features Cutting material: Polykristalliner Diamant (PCD) Chipbreaker: DIA Plate form: Rhombic Typical application: Turning (external and internal) Compatibility: ISO standard; selection of holder depends on form, clearance, tolerance, fastening, size and thickness FAQ What materials is the insert intended for? The DX120 PCD grade is designed primarily for aluminium and other non-ferrous metals, as well as abrasive non-metallic materials where diamond tooling provides superior wear resistance. Which holders are compatible with this insert? Compatibility requires a matching ISO rhombic form, correct clearance angle and tolerance class; the insert is intended for standard VCMT external holders and appropriate boring bars when those parameters are met. How does the 0.4 mm corner radius affect the finish? A 0.4 mm corner radius provides a balance between a fine surface finish and edge strength, suitable for finishing cuts on non-ferrous components without excessively increasing cutting forces. Is the insert suitable for interrupted cuts? Yes, the carbide backing under the PCD layer offers mechanical stability that helps withstand moderate interruptions; suitability depends on the specific application and cutting parameters. What are the benefits of the DX120 grade compared with carbide inserts? DX120 PCD delivers significantly longer tool life and higher achievable cutting speeds on suitable materials, reducing tool-change frequency and improving production consistency. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
VCMT 160404 GT9530 Wendeplatten - Tungaloy
Take advantage of high‑quality finishing and extended tool life through the combination of a coated cermet grade and a stable PS chipbreaker design; order the VCMT160404-PS GT9530 directly via Metav Werkzeuge or consult our specialists for application support. VCMT 160404 GT9530 — ISO turning insert, coated cermet, PS chipbreaker | Tungaloy The VCMT160404‑PS GT9530 is an ISO‑standard rhombic turning insert designed for finishing and light universal turning of steel where surface quality and tool life are priorities ISO rhombic insert VCMT 160404 PS chipbreaker Coated cermet grade GT9530 for longer life 7° clearance and 35° approach angle for stability Cylindrical hole with single‑side countersink 40°–60° Precise finishing with durable cermet technology The VCMT160404‑PS GT9530 combines a coated cermet cutting material with a geometry geared towards finishing and light universal turning. The GT9530 grade delivers extended tool life under stable set‑ups while maintaining a fine surface finish, reducing the need for secondary passes. Cermet grades are designed to resist abrasive wear and to preserve a sharp cutting edge; this means fewer interruptions for insert changes and a more consistent part quality across production runs. Predictable chip control for consistent productivity The PS chipbreaker offers controlled chip formation at finishing feeds and moderate depths of cut, helping to avoid entanglement and irregular chip shapes that can harm surface integrity. The combination of chipbreaker and grade promotes a short, curlable chip under recommended conditions, so cycle times remain stable and disposal is safer. The insert’s cylindrical hole with a 40°–60° countersink assures reliable clamping and repeatable positioning in standard screw‑clamp holders. Straightforward ISO compatibility and secure clamping Manufactured to ISO dimensions, the rhombic shape and precise tolerances simplify retrofitting into existing holder systems when form, clearance angle, tolerance class, attachment method, size and thickness match. Key geometry values such as 35° approach angle, 7° clearance angle, radius 0.4 mm and 4.76 mm thickness support stable cutting behaviour and predictable tool engagement. These characteristics make the insert suitable for both external and internal facing operations when used with an appropriate holder and set‑up. Recommended applications and machining guidance This grade and geometry are optimised for machining steel in finishing or light universal operations where excellent surface quality and consistent edge life are required. For best results, select the chipbreaker and grade that match workpiece material, machine rigidity and cutting parameters; the combination of a stable set‑up and the GT9530 coating yields repeatable results and reduced scrap rates. When in doubt about the best chipbreaker or cutting data for a specific job, Metav Werkzeuge can provide tailored recommendations. For procurement and application guidance on the Tungaloy VCMT160404‑PS GT9530 insert, contact Metav Werkzeuge at info@metav-werkzeuge.com or call +49 2822 7131930 to discuss availability and suitable holder combinations Technical data Article number: 6998416 Manufacturer SKU: TUN6998416 Product SKU: 6998416-Tungaloy Model designation: VCMT160404-PS GT9530 Label: VCMT160404-PS GT9530 Core dimensions Inscribed size: 16 mm Thickness: 4.76 mm Corner radius: 0.4 mm Approach angle: 35° Clearance angle: 7° Materials & features Grade: GT9530 Cutting material: coated cermet Chipbreaker: PS Hole: cylindrical hole + single‑side countersink (40°–60°) Shape: rhombic Application: Turning Series: ISO turning inserts Manufacturer: Tungaloy FAQ Which materials is this insert best suited for? The GT9530 grade is formulated for machining steel in finishing to light universal turning; the VCMT160404‑PS insert performs well where a fine surface finish and longer tool life are required. How does the PS chipbreaker influence machining behaviour? The PS chipbreaker promotes short, controllable chips at finishing feeds, improving surface integrity and enabling safer chip handling with the VCMT160404‑PS GT9530 insert. What must be checked for holder compatibility? Compatibility depends on form, clearance angle, tolerance class, attachment, size and thickness; ensure the ISO‑standard rhombic geometry and the 4.76 mm thickness match the chosen holder before fitting. Is the insert suitable for internal and external turning? Yes; the geometry and chipbreaker suit both external and internal operations, provided the holder and set‑up offer sufficient rigidity for finishing cuts with the GT9530 grade. What are the identifying codes for ordering? Order using the model designation VCMT160404‑PS GT9530 or the article number 6998416; the manufacturer SKU is TUN6998416. Manufacturer/Responsible: Tungaloy‑NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand‑new product from the manufacturer.
VCMT 160404 GT9530 Wendeplatten - Tungaloy
High-performance finishing and reliable wear resistance are delivered by the GT9530 coated cermet and the PF chipbreaker, providing consistent surface quality and longer tool life in stable turning operations. Order the VCMT160404-PF GT9530 directly via Metav Werkzeuge or ask the consultants for application-specific recommendations. VCMT160404-PF GT9530 ISO indexable turning insert for Turning — Tungaloy The VCMT160404-PF GT9530 is an ISO-format indexable turning insert designed for finishing and light universal turning, optimised to deliver fine surface finishes and extended tool life in stable machining setups. ISO rhombic insert, 16 mm size GT9530 coated cermet for fine finishing PF chipbreaker for stable surface quality 0.4 mm corner radius with 4.76 mm thickness Consistent surface quality and prolonged tool life The combination of the GT9530 coated cermet and the PF chipbreaker is aimed at finishing applications where surface integrity matters. The coating and cermet core improve wear resistance and edge retention under steady cutting conditions, which reduces the need for frequent index changes and contributes to a more predictable tool-life cycle. This results in fewer interruptions on the shop floor and a steadier output quality when machining steel; the insert design supports a fine surface finish without aggressive feed steps. Clear compatibility and secure clamping for reliable set-up Compliance with ISO geometry ensures that the insert fits standard holders when the form, relief angle, tolerance class, fastening method, size and thickness match. The VCMT160404-PF features a cylindrical hole with a one-sided countersink (40°–60°) for secure axial locating and clamping, and the 7° free angle supports stable cutting with reduced rubbing on the flank. Specifying the correct holder and clamping accessories according to ISO norms shortens set-up time and reduces chatter risks, improving process stability for both external and internal turning tasks. Practical selection guidance and machining approach For finishing on steel under rigid conditions, the GT9530 grade provides a balance between wear resistance and surface quality; select modest cutting depths and controlled feed rates to exploit the insert’s strengths. The 0.4 mm corner radius supports fine edge definition while the 4.76 mm thickness and 16 mm size deliver sufficient mechanical support for light turning operations. Match the chipbreaker to material and stability: the PF chipbreaker helps form short, manageable chips and supports consistent surface results. For unfamiliar materials or unstable setups, prefer more robust geometry or a different chipbreaker to prioritise process security. For application advice, tailored cutting data or to order the VCMT160404-PF GT9530 from Tungaloy, contact Metav Werkzeuge — email info@metav-werkzeuge.com or call +49 2822 7131930 for expert consulting and quick availability. Technical Data Article number: 6998403 Manufacturer SKU: TUN6998403 Metav SKU: 6998403-Tungaloy Model series: ISO indexable turning inserts Designation: VCMT160404-PF GT9530 Application: Turning (external and internal turning) Core dimensions Insert size: 16 mm Thickness: 4.76 mm Corner radius: 0.4 mm Free angle: 7° Approach angle: 35° Countersink angle: 40°–60° Materials & special features Grade: GT9530, coated cermet Chipbreaker: PF Shape: rhombic Hole style: cylindrical hole with one-sided countersink Material: hard material (cermet) FAQ What is the main application for this insert? The VCMT160404-PF GT9530 from Tungaloy is intended for finishing and light universal turning of steel, offering improved surface quality and longer edge life in stable machining conditions. Which holder and clamping criteria determine compatibility? Compatibility is governed by ISO geometry: form, relief (free) angle, tolerance class, fastening method, size and thickness must match the chosen holder; the VCMT160404-PF uses a cylindrical hole with a one-sided countersink for secure clamping. How does the PF chipbreaker influence machining performance? The PF chipbreaker produces short, controlled chips and supports consistent surface finishes, making it suitable for finishing passes and situations where predictable chip flow and low re-cutting are priorities. What starting parameters are suggested for finishing steel? Begin with moderate cutting speeds and conservative feeds appropriate for finishing, ensure a rigid set-up and employ the GT9530 grade for extended edge life; adjust parameters gradually to balance surface quality and productivity. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
VCMT 160404 GT9530 Wendeplatten - Tungaloy
Take advantage of the combination of coated cermet durability, precise ISO compatibility and the PSS chipbreaker for reliable finishing results; order the VCMT 160404 GT9530 directly via Metav Werkzeuge or consult our technical advisors for application support. VCMT 160404 GT9530 – ISO turning insert (coated cermet, PSS chipbreaker) by Tungaloy The VCMT 160404 GT9530 is an ISO‑format rhombic turning insert designed for finishing to light universal turning, offering a coated cermet grade optimised for steel under stable machining conditions Coated cermet GT9530 for improved wear resistance PSS chipbreaker for finishing and light turning Rhombic ISO VCMT 160404, 0.4 mm corner radius Cylindrical hole + 40°–60° countersink, 7° clearance Higher surface quality and longer tool life for finishing operations The insert delivers a consistent combination of surface finish and tool life thanks to the GT9530 cermet grade and its protective coating. Cermet cutting materials are engineered to combine the hardness of ceramics with the toughness of metal binders; this translates into better abrasion resistance and superior edge integrity when turning steel under steady process conditions. The PSS chipbreaker is tuned for light to finishing cuts, reducing chip entanglement and promoting predictable chip flow, which supports repeatable part quality and less frequent tool changes. Emphasis is placed on measurable benefits such as reduced rework and longer intervals between insert changes. Accurate fit and predictable clamping for secure machining Compatibility with the toolholder is determined by form, relief angle, tolerance class, fastening, size and thickness; the rhombic ISO shape and standard hole geometry of this insert ensure reliable seating in ISO‑type external holders. Key dimensions—16 mm inscribed size, 4.76 mm plate thickness and 0.4 mm corner radius—contribute to consistent positioning and cutting geometry. The 7° clearance supports stable cutting engagement while the cylindrical hole with one‑sided countersink (40°–60°) simplifies secure fastening and repeatable indexing. Clear, standardised mechanical interfaces minimise assembly time and reduce vibration risk, supporting more stable cutting conditions and enhanced process control. Selection guidance and application scope for production planning Choose this insert where finishing or light universal turning of steel is required and where stable machining set‑ups are present. The coated cermet formulation is particularly suited to jobs prioritising surface integrity and longer wear life rather than heavy roughing. For mixed tasks, matching the PSS chipbreaker and GT9530 grade to the workpiece material and cutting data is essential; softer, interrupted or unstable cuts may call for a different geometry or grade. Where process reliability is critical, specify the ISO‑standard insert form to ensure interchangeability between holders, simplify inventory and standardise tool change procedures. For ordering and tailored advice on the VCMT 160404 GT9530 from Tungaloy, contact Metav Werkzeuge — email info@metav-werkzeuge.com or call +49 2822 7131930 for application support and procurement assistance Technical Data Article number: 6998411 Manufacturer SKU: TUN6998411 SKU: 6998411-Tungaloy Model series: ISO turning inserts Designation: VCMT160404-PSS GT9530 Facts Inscribed size: 16 mm Plate thickness: 4.76 mm Corner radius: 0.4 mm Clearance angle: 7° Insert angle: 35° Special features Coated cermet cutting material (GT9530) PSS chipbreaker for finishing/light turning Rhombic insert form VCMT 160404 Cylindrical hole with one‑sided countersink (40°–60°) Suitable for turning of steel under stable conditions ISO‑standard compatibility for external holders FAQ What materials is this insert intended for? The VCMT 160404 GT9530 is specified for turning steel, with the GT9530 coated cermet grade providing enhanced wear resistance for finishing and light universal applications. How does the PSS chipbreaker affect performance? The PSS chipbreaker promotes controlled chip formation during finishing cuts; with the GT9530 grade it helps maintain surface quality and reduces risk of chip interference in stable machining conditions. Is the insert compatible with standard ISO holders? Yes, the insert follows ISO dimensions and hole geometry (cylindrical hole + 40°–60° countersink), allowing secure clamping in ISO‑type external holders when the holder matches the insert form and tolerance class. What cutting geometry is offered for edge integrity? This rhombic insert provides a 0.4 mm corner radius and a 7° clearance angle, designed to balance edge strength and surface finish during finishing operations. Which SKU should be ordered for this item? Order using SKU 6998411‑Tungaloy or manufacturer SKU TUN6998411 to ensure the correct VCMT160404‑PSS GT9530 item is supplied. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
VCMT 160404 NS9530 Wendeplatten - Tungaloy
Take advantage of the VCMT160404-PS NS9530 combination of a sharp-edge cermet grade and ISO‑standard geometry for consistent finishing on steel; the insert’s low cutting forces and fine corner radius support higher first-pass quality and reduced rework. Order directly via Metav Werkzeuge or request guidance from our consultants for optimum holder selection. VCMT160404-PS 160404 NS9530 – ISO turning insert for Turning by Tungaloy A VCMT160404-PS NS9530 ISO turning insert designed as a finishing-grade cermet for external and internal turning of steel. Finishing cermet grade NS9530 Sharp cutting edge for superior surface finish Ideal for continuous cuts and small depths ISO 160404; 7° clearance; 0.4 mm radius Consistent finishing and improved part quality The uncoated cermet grade NS9530 delivers a finishing grade optimised for low cut forces and an exceptionally sharp cutting edge, which translates directly into better first-pass surface integrity and reduced secondary operations. In practice, this means fewer passes to reach dimensional tolerances and a superior surface finish on turned components made from steel. The combination of a small corner radius and the grade’s edge retention supports stable performance during continuous cuts and small depths of cut, enabling predictable cycle times and less scrap. Reliable fit within ISO tool systems for straightforward integration As an ISO-normed insert, the VCMT160404-PS is compatible with holders when form, clearance angle, tolerance class, fastening method, size and thickness are matched. The rhombic geometry with a cylindrical hole and single-sided countersink (40°–60°) ensures secure clamping and repeatable seating in standard clamping systems. Key dimensions such as 16 mm inscribed circle, 4.76 mm thickness and the 0.4 mm corner radius make selection of the correct seat and screw straightforward, reducing setup time and promoting repeatable tool life across batches. Practical application: when to choose this insert and how to use it Select the VCMT160404-PS for finishing operations on steel where continuous cutting and small depths of cut dominate the cycle. Pair the insert’s PS chipbreaker with a stable holder and rigid workholding to exploit the grade’s low cutting forces and minimise vibration. For abrasive or interrupted cuts consider alternative grades; for high-feed or roughing tasks select a chipbreaker and geometry optimised for higher stock removal. For further parameter tuning or compatibility checks, Metav Werkzeuge’s technical team can advise on holders, clamping sets and spare screws to ensure the insert performs as intended. Contact Metav Werkzeuge for tailored advice on Tungaloy finishing inserts and fast, reliable supply; email info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: 6998606-Tungaloy Manufacturer article number: 6998606 SKU manufacturer: TUN6998606 Model series: ISO turning inserts Core dimensions Inscribed circle: 16 mm Thickness: 4.76 mm Corner radius: 0.4 mm Clearance angle: 7° ISO code: 160404 Included angle: 35° Design and special features Rhombic plate form With hole; cylindrical hole + one-sided countersink (40°–60°) Chipbreaker: PS Grade: NS9530 Uncoated cermet cutting material Suitable for turning (external and internal) Material base: cemented carbide substrate FAQ What materials is this insert best suited for? The VCMT160404-PS NS9530 is a finishing-grade cermet optimised for turning on steel, offering low cutting forces and excellent surface finish on continuous cuts. What are the key dimensions and codes to check before ordering? Check the ISO code 160404, inscribed circle 16 mm, thickness 4.76 mm, corner radius 0.4 mm and the clearance angle 7°; the manufacturer article number is 6998606. Is the cutting material coated? No, the VCMT160404-PS NS9530 is an uncoated cermet grade designed for sharp-edge finishing performance. Which chipbreaker does this insert use and what is its purpose? This insert uses the PS chipbreaker; select this chipbreaker for controlled chip formation during continuous finishing cuts to improve surface quality. How can compatibility with existing holders be ensured? Compatibility is determined by insert form, clearance angle, tolerance class, fastening style, size and thickness; confirm these parameters against the holder specification or consult Metav Werkzeuge for verification. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
VCMT 160404 NS9530 Wendeplatten - Tungaloy
Take advantage of the combination of precision finishing, low cutting forces and predictable chip control for consistently high surface quality. Order the insert directly via Metav Werkzeuge or ask the consultants for holder recommendations and availability. VCMT 160404 NS9530 indexable turning insert for turning (Tungaloy) A versatile ISO indexable turning insert, VCMT160404-PSS NS9530, engineered for finishing steel with a sharp cutting edge and optimised chip formation. ISO rhombic insert VCMT 160404 form Uncoated cermet NS9530 for fine finishing 0.4 mm corner radius with PSS chipbreaker High-precision finishing with reduced cutting forces The ISO-compatible grade is designed as a finishing solution for steel, providing a sharp cutting edge and inherently low cutting forces. The uncoated cermet grade NS9530 is specified for continuous cuts and small depths of cut; this combination helps to deliver a high surface quality while keeping power draw and vibration to a minimum. For production environments where repeatable finishes and component tolerances matter, this grade supports consistent part quality and predictable tool behaviour during long runs. Geometry and clamping that enhance process stability The insert’s 0.4 mm corner radius improves surface finish without excessive tool engagement, while the 7° clearance angle and the 35° approach angle support clean shearing and reduced rubbing. The PSS chipbreaker is designed to control chips in finishing operations, enabling safe evacuation and reduced risk of surface damage. Compatibility with holders depends on insert shape, clearance, tolerance class, fastening method, size and thickness; use matched external holders or boring bars together with the correct shim and clamping set to ensure stable, repeatable clamping. Practical system advice for reliable results Integrated into a standard ISO system—insert, appropriate external holder or boring bar, shim/clamp set and replacement screws—the component excels in turning operations that demand a fine finish. The design and grade prioritise process stability: the uncoated NS9530 grade provides a keen edge for finishing, but benefits most when mounted in a rigid setup and used with controlled feeds and depths. The overall system approach reduces rework, extends effective time between changeovers and supports efficient throughput in serial production. For tailored holder matching, technical advice or stock information contact Metav Werkzeuge by email at info@metav-werkzeuge.com or by phone on +49 2822 7131930 for fast, application-oriented support and availability. Technical Data Article number: 6998601 Manufacturer SKU: TUN6998601 Label: VCMT160404-PSS NS9530 Model series: ISO indexable turning inserts Core dimensions Corner radius: 0.4 mm Thickness: 4.76 mm Ins. size: 16 mm Clearance angle: 7° Approach angle: 35° Hole: with hole Features & compatibility Uncoated cermet grade NS9530 PSS chipbreaker Rhombic insert shape (VCMT) Cylindrical hole with single-sided countersink (40°–60°) ISO-form compatibility; check holder form, clearance, tolerance, fastening, size and thickness Designed for external and internal turning Finishing grade for steel; optimised for continuous cuts and small depths FAQ What materials is this insert intended for? The VCMT160404-PSS NS9530 insert is specified as a finishing grade for steel applications, with the NS9530 cermet composition optimised for continuous cuts and high surface quality. Which holder types are compatible with this insert? Compatibility relies on the ISO insert form and dimensions: match the rhombic VCMT 160404 form with an appropriate external holder or boring bar that accepts inserts of 16 mm size, 4.76 mm thickness and the stated clearance angle. Is the insert suitable for interrupted or heavy roughing cuts? The NS9530 finishing grade with the PSS chipbreaker is best used for continuous finishing cuts and small depths; heavy interrupted or roughing cuts will generally require a tougher, coated grade optimised for higher edge strength. How does the PSS chipbreaker affect machining? The PSS chipbreaker promotes controlled chip formation during finishing operations, supporting consistent evacuation and reducing the likelihood of surface damage while aiding stable cutting forces. What is the purpose of the 0.4 mm corner radius? A 0.4 mm corner radius balances edge strength with the ability to achieve smooth surfaces; it reduces the tendency for tool chipping compared with a sharper radius while still enabling fine surface finishes. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com