What does a limit plug gauge cost?

Take advantage of accurate diameter checks, a compact 0.5–10 mm range and robust steel construction to streamline drill verification in the workshop. Order the item directly via Metav Werkzeuge or consult our specialists for tailored advice. Drill Gauge MS910.501 — steel drill gauge, 0.5–10 mm range The Drill Gauge MS910.501 is a compact steel gauge designed for rapid identification and verification of drill diameters in workshop, tooling and inspection environments. Robust steel construction Measuring range 0.5–10 mm Steps every 0.1 mm for quick checks Compact size ideal for micro measurements Fast, reliable diameter checks that speed up inspection The instrument enables immediate validation of drill sizes, offering a measuring range of 0.5–10 mm with clear, regular increments of 0.1 mm for fast go/no-go decisions. This makes the tool particularly effective when time is critical: operators spend less time searching for the right drill and more time on machining. The compact form factor supports quick handling at the bench or next to a machine, reducing workflow interruptions and improving throughput. Built for repeatable precision and easy interpretation Constructed from steel for consistent dimensional stability and wear resistance, the gauge provides repeatable checks across many cycles of use. The regular step spacing simplifies visual comparison between the tool and the corresponding gauge slot, which is especially useful when a production line requires fast sampling rather than laboratory-level metrology. The simple mechanical design avoids electronics, so operation remains straightforward and maintenance demands are minimal while preserving dependable performance. Suited to micro work and small-scale quality control With its maximum measuring range of 10 mm, the gauge is classified in the micro category—ideal for fine mechanical and watchmaking tasks as well as routine checks in general machining where small-diameter drills are common. The tool supports quick decision-making during setup and run-time inspections, contributing to consistent part quality and fewer tool-change mistakes. Where traceable calibration is required, consultancy on calibration options can be provided to match workshop quality routines. Contact Metav Werkzeuge for procurement details, calibration options and application advice on the Filetta Drill Gauge MS910.501 — direct supply from Emmerich to the workshop bench. Technical data Article number: MS910.501 Manufacturer: Filetta Type: Drill gauge Facts Measuring range: 0.5–10 mm Step size: 0.1 mm Minimum: 0.5 mm Maximum: 10 mm Special features Material: Steel Application: Drill diameter verification Category: Gauges / Measuring pins FAQ What measuring range does this gauge cover? The gauge covers a range from 0.5 mm to 10 mm, making the Drill Gauge MS910.501 suitable for small-diameter drill checks. How fine are the increments on the gauge? Increments are 0.1 mm, which allows for quick visual checks and straightforward go/no-go comparison when verifying drill diameters. Is the gauge suitable for workshop use or only for metrology labs? Designed for practical workshop use, the Filetta drill gauge provides robust, repeatable checks ideal for bench and production environments. What material is the gauge made from? The gauge is made from steel, selected for dimensional stability and wear resistance under regular inspection cycles. Can the gauge be used during machine setup? Yes, the compact size and clear steps make the MS910.501 convenient for use during machine setup and routine sampling inspections. Manufacturer / Responsible: Schut Geometrische Meettechniek bv; Duinkerkenstraat 21; 9723 BN Groningen; The Netherlands; +31 50 5877877; schutnl@schut.com

Reliable 11 mm limit plug gauge manufactured from hardened steel and produced to DIN 7162 ensures consistent go/no‑go inspection and predictable wear behaviour; order directly via Metav Werkzeuge or consult our specialists for application advice. Limit plug gauge MS911.215 — Filetta, 11 mm, hardened steel (DIN 7162) The Limit plug gauge MS911.215 is a precision inspection pin for go/no‑go checks of internal diameters in production and quality control environments. Hardened steel for long service life DIN 7162 standard compliance 11 mm nominal diameter for bore checks Wear allowance on good side Consistent inspection backed by an industry standard This gauge pin delivers reliable, repeatable checks for internal bores, designed to support standardised quality workflows. Manufactured in accordance with DIN 7162, the tool provides a clear reference for pass/fail decisions and integrates readily into established inspection sequences. The 11 mm nominal dimension is presented as a precise measuring reference, and the geometry of the pin minimises wobble during insertion to improve repeatability and reduce measurement scatter in serial inspection. Robust construction for long operational life Made from hardened steel, the pin resists surface damage and maintains its working diameter under frequent use. The design incorporates a wear allowance on the good side, which signals gradual material loss without compromising the functional check; this feature extends usable life while making wear visible during routine inspections. For workshops that demand low downtime, the material choice and finish reduce the need for frequent replacement and support uninterrupted production checks. Practical application and handling in the workshop The plug gauge is intended for quick go/no‑go checks on internal diameters in machining, assembly and incoming inspection stations. Its compact form enables fast handling and clear pass/fail interpretation, supporting efficient throughput without complex procedures. Markings and standard conformity simplify traceability and documentation, while the sturdy construction keeps maintenance straightforward and predictable. The Filetta badge denotes established toolmaking expertise and suitability for industrial environments where dependable gaging is required. For application-specific advice on using this Filetta limit plug gauge and to obtain supply directly from Metav Werkzeuge in Emmerich, contact our team for tailored recommendations and fast delivery Technical data Article number: MS911.215 Manufacturer: Filetta Material: hardened steel Facts Nominal diameter: 11 mm Special features DIN 7162 compliant Wear allowance on good side Application: internal bore go/no‑go inspection Category: gauge pins / plug gauges FAQ What is the primary application of this gauge? The Filetta limit plug gauge MS911.215 is intended for go/no‑go inspection of internal diameters during production and quality control. What does the wear allowance on the good side mean? The wear allowance indicates a deliberate tolerance on the pass side so that gradual surface wear can be detected without immediately affecting the go/no‑go result, extending usable life. Is this gauge compliant with recognised standards? Yes, the plug gauge is manufactured in accordance with DIN 7162, which governs limit gauge design and marking. What is the exact nominal size of the pin? The nominal diameter is 11 mm; reference and tolerance interpretation follow DIN 7162 specifications. Which workshop environments are suitable for this tool? The gauge is suited to machining, assembly and incoming inspection where compact, rapid internal diameter checks are required; its hardened steel construction supports frequent use. Manufacturer / Responsible: Schut Geometrische Meettechniek bv; Duinkerkenstraat 21; 9723 BN Groningen; The Netherlands; +31 50 5877877; schutnl@schut.com

Take advantage of precise, fast pass/fail checks and robust wear resistance thanks to hardened steel and DIN 7162 conformity; order the matching gauge pins directly via Metav Werkzeuge or contact our consultants for batch and inspection advice. Limit Gauge Pin — hardened-steel inspection pin, 11 mm, DIN 7162 (Filetta) The Limit Gauge Pin is a hardened-steel inspection pin designed for rapid go/no-go checks and routine dimensional control in workshops and inspection benches, compliant with DIN 7162. Hardened-steel construction for long service life Conforms to DIN 7162 for consistent tolerances 11 mm nominal diameter for standard inspection tasks Wear allowance on the good side to extend usable life Faster, reliable pass/fail inspection for production lines The compact inspection pin delivers quick go/no-go checks that reduce measuring time at control points and on the shop floor. By providing an unequivocal pass or fail condition, the pin supports efficient decision-making in both single-piece inspections and repetitive sampling routines. Conformity with DIN 7162 ensures that the nominal diameter and tolerance band are traceable to an established standard, which simplifies integration into existing inspection protocols and statistical process control. Robust build that minimises downtime Thanks to its hardened steel construction the pin withstands repeated contact without rapid degradation, while the specified wear allowance on the good side preserves the functional limit for longer. This translates into fewer replacements, reduced downtime and lower indirect costs from inspection interruptions. The hardened surface also keeps seating and mating surfaces consistent, helping to avoid false rejects that would otherwise increase rework. Practical benefits for inspection benches and gauge sets As a dedicated inspection pin, the component is optimised for quick handling and straightforward verification tasks on inspection benches and assembly jigs. The clear go/no-go characteristic reduces interpretation time for operators and speeds up routine quality checks. For quality managers the result is measurable: quicker throughput at control stations and a more consistent acceptance rate across batches. Traceability and suitability for regular quality workflows Manufactured to industry standard, the pin supports consistent batch-to-batch performance and straightforward inventory management when used in gauge sets or fixed inspection fixtures. The simple geometry and standardised tolerance regime make the item suitable for assembly audits, incoming inspections and periodic verification of tool wear, providing procurement confidence for maintenance and quality teams. Request technical advice or a batch availability check from Metav Werkzeuge in Emmerich to align delivery options with production schedules Technical Data Article number: MS911.173 Name: Limit Gauge Pin Material: hardened steel Standard: DIN 7162 Measurements / Core data Diameter: 11 mm Features / Applications Wear allowance on the good side Hardened for wear resistance Intended for go/no-go inspection tasks Category: gauge pins / inspection pins FAQ What is the nominal diameter of this inspection pin? The inspection pin has a nominal diameter of 11 mm; this specification applies to the Filetta limit gauge pin (SKU MS911.173). Is the pin suitable for go/no-go checks on assembly lines? Yes, the Filetta limit gauge pin is designed for rapid pass/fail checks and is suitable for routine assembly-line and workshop inspections. What material is used and how does it affect service life? The pin is made from hardened steel, which increases wear resistance and extends usable life compared with untreated pins. Which standard governs the pin’s tolerances? Tolerances and dimensions conform to DIN 7162, providing a recognised reference for inspection procedures. How does the wear allowance on the good side affect inspection practice? The specified wear allowance on the good side allows continued use while preserving the functional limit for a longer period, reducing unnecessary replacements Manufacturer / Responsible: Schut Geometrische Meettechniek bv; Duinkerkenstraat 21; 9723 BN Groningen; The Netherlands; +31 50 5877877; schutnl@schut.com

Take advantage of a hardened-steel, DIN 7162 compliant design with an integrated wear allowance on the good side to maintain reliable go/no-go checks throughout production. The robust Ø 16 mm construction supports repeatable limit inspection and reduces rework. Order the Filetta limit pin gauge directly via Metav Werkzeuge or ask our consultants for application advice. Filetta limit pin gauge – hardened steel, DIN 7162, Ø 16 mm The limit pin gauge is a precision checking pin for fast go/no-go verification of bores and fits in machine shops and inspection benches. Hardened steel construction Compliant with DIN 7162 Wear allowance on good side Consistent limit checks that keep production moving Designed for straightforward go/no-go inspection, this checking pin offers a compact method to control bore limits without complex setup. The hardened steel body preserves the gauge geometry under repeated use, which improves repeatability and reduces the need for corrective machining. Using a defined limit pin accelerates routine quality checks and shortens inspection cycles, delivering measurable efficiency gains on the shop floor. Built for durability and traceable performance A wear margin on the good side compensates for gradual abrasion, prolonging the service life while keeping functional checks reliable. Compliance with DIN 7162 places the component within a recognised framework for limit gauges, simplifying documentation and audit trails. The robust Ø 16 mm format balances stiffness and handling for frequent tactile checks, enabling quick decision-making at the bench without compromising measurement integrity. Simple handling, clear results for workshop use The geometry of the pin supports immediate tactile feedback in pass/fail inspection: the "go" condition should fit into the bore, while the "no-go" condition must be rejected. This binary outcome removes ambiguity from routine testing and helps maintain throughput. The gauge’s straightforward form factor makes it suitable for integration into existing inspection routines or as a portable verification tool carried between workstations. For specification support or to obtain the Filetta limit pin gauge Ø 16 mm (MS911.178), contact Metav Werkzeuge in Emmerich by phone at +49 2822 7131930 or by email at info@metav-werkzeuge.com Technical data Article number: MS911.178 Name: Limit pin gauge Material: hardened steel Standard: DIN 7162 Facts Diameter: 16 mm Category: gauges / test pins Special features Wear allowance on the good side Hardened material for durability FAQ What is the primary use of this limit pin gauge? The Filetta limit pin gauge (MS911.178) is used for fast go/no-go verification of bores and mating fits on production lines and inspection benches. Does the gauge comply with industry standards? Yes, the Filetta limit pin gauge is manufactured to comply with DIN 7162, ensuring it matches recognised requirements for limit gauges. How does the wear allowance affect long-term use? The built-in wear allowance on the good side extends usable life by compensating for gradual surface wear, keeping checks functionally reliable over time with less frequent replacement. What size is this checking pin and how is it handled? The checking pin is Ø 16 mm and is sized for easy tactile go/no-go inspections; its hardened construction supports repeatable handling in workshop environments. Manufacturer / Responsible: Schut Geometrische Meettechniek bv; Duinkerkenstraat 21; 9723 BN Groningen; The Netherlands; +31 50 5877877; schutnl@schut.com

Take advantage of a standards‑based inspection tool that pairs hardened steel construction with DIN 7162 conformity and a practical wear allowance on the go side, ensuring reliable pass/fail checks and prolonged service life; order the gauge directly via Metav Werkzeuge or consult our team for application advice. Filetta Limit Plug Gauge G7 – 19 mm, hardened steel (DIN 7162) A Filetta Limit Plug Gauge G7 designed for fast go/no-go verification of 19 mm bores in line with DIN 7162 for consistent production control Hardened steel construction Conforms to DIN 7162 19 mm nominal diameter Wear allowance on the go side Rapid, standards‑compliant inspection that saves time A purpose‑built limit plug gauge provides an immediate quality decision: go/no-go assessment without the need for complex readouts. Conformity with DIN 7162 guarantees the gauge’s dimensions and tolerances match recognised inspection criteria, which accelerates in‑process checks and reduces bottlenecks on the production line. The 19 mm nominal diameter is specified for direct matching to mating bores; using a dedicated gauge for this diameter simplifies sampling plans and shortens cycle time while maintaining clear, auditable acceptance criteria. Robust construction for lasting accuracy Made from hardened steel, the gauge resists wear and maintains geometry across repeated use, which sustains repeatability of results. The design includes a wear allowance on the go side, a planned material margin that can be used to extend the service life before the gauge reaches its limit condition. In practical terms, the wear allowance postpones replacement, lowers lifetime cost, and preserves measurement integrity—critical when inspections are frequent or when a single gauge serves multiple machines or workstations. Easy integration into shop‑floor routines and quality systems The compact, single‑purpose format of this limit plug gauge suits assembly lines, quality control benches and manual inspection jigs. Implementation requires minimal training: the visual or tactile pass/fail outcome reduces interpretation time compared with continuous measuring instruments. For organisations aiming to standardise inspection methods, the gauge fits into existing metrological workflows and documentation. Metav’s position as a precision partner supports straightforward procurement and reliable supply from Emmerich, backed by decades of distribution experience for industrial metrology. Contact Metav Werkzeuge today to confirm suitability and request delivery of the Filetta Limit Plug Gauge G7 (SKU MS911.181); Metav’s advisors in Emmerich will provide practical guidance and rapid fulfilment Technical data Article number: MS911.181 Manufacturer: Filetta Designation: Limit plug gauge G7 Facts Nominal diameter: 19 mm Standard: DIN 7162 Special features Material: hardened steel Wear allowance on the go side Category: gauges / plug gauges / inspection pins FAQ What inspection task is this gauge intended for? The Filetta Limit Plug Gauge G7 (SKU MS911.181) is intended for quick go/no-go verification of 19 mm internal bore dimensions to support routine pass/fail inspection. Which standard does the gauge comply with? This limit plug gauge is manufactured to conform with DIN 7162, ensuring dimensional and tolerance compatibility for standardised checks. How does the wear allowance affect service life? The wear allowance on the go side provides an engineered margin that prolongs usable life by allowing controlled wear before the gauge reaches its limit condition. What material is the gauge made from and why does that matter? The gauge is made from hardened steel, which maintains geometry under repeated use and supports long‑term repeatability of inspection results. Can this gauge be used in automated inspection fixtures? Yes, the solid construction and single‑function geometry of this plug gauge make it suitable for integration into manual and automated fixtures where a 19 mm go/no-go check is required. Manufacturer / Responsible: Schut Geometrische Meettechniek bv; Duinkerkenstraat 21; 9723 BN Groningen; The Netherlands; +31 50 5877877; schutnl@schut.com

Take advantage of a robust combination of hardened steel construction, DIN 7162 conformity and a specified wear allowance on the good side to ensure stable go/no-go inspection results; order the gauge directly via Metav Werkzeuge or consult our advisors for application support. Limit plug gauge (go/no-go) – hardened steel, DIN 7162 | Filetta The limit plug gauge is a hardened steel go/no-go instrument designed for rapid inspection of bore diameters in mechanical production and quality control environments. Hardened steel construction Conforms to DIN 7162 standard Wear allowance on 'good' side Suitable for go/no-go bore checks Reliable inspection that stabilises quality control A compact plug gauge built from hardened steel, manufactured to DIN 7162, offers a straightforward and verifiable check of bore conformity. The compact design supports quick in-process inspection, enabling repetitive pass/fail assessments with minimal setup. By using a dedicated limit gauge rather than improvised measuring methods, production lines gain predictable throughput and a reduced risk of downstream rejects, translating into measurable time savings during routine quality checks. Design detail that extends service life and repeatability The integrated wear allowance on the 'good' side compensates for gradual material loss at the contact surfaces so the "Go" dimension remains within tolerance for longer service intervals. This allowance is a pragmatic engineering measure: it preserves the reference condition of the gauge under regular use and simplifies maintenance planning. In practice, the clear distinction between the Go and No‑Go ends accelerates operator decisions and reduces subjective judgement during inspections. Robust build for workshop and production use Constructed from hardened steel and intended as a repeatable limit reference, this plug gauge is suitable for workshop inspection benches and production stop‑checks alike. The straightforward go/no-go principle means checks are fast, training effort is low and measurement routines are easy to embed into quality plans. Supplied as a standard plug gauge by Filetta, the item is particularly suited to machine shops and inspection departments that prioritise durable, standard‑compliant instruments for daily use. For tailored advice and supply from Metav Werkzeuge, order the Filetta limit plug gauge MS911.202 or request application guidance by emailing info@metav-werkzeuge.com or calling +49 2822 7131930 Technical data Article number: MS911.202 Material: hardened steel Standard: DIN 7162 Special feature: wear allowance on 'good' side Nominal size: 2 mm Core data Nominal size: 2 mm Special features Go/no-go functionality for bore inspection Hardened steel for extended durability Conforms to DIN 7162 specification Category: plug gauge / limit gauge Brand: Filetta FAQ What is the primary use of this plug gauge? The limit plug gauge is used for rapid go/no-go checks of bore diameters to confirm whether components meet the specified tolerance. How does the wear allowance affect inspection intervals? The wear allowance on the 'good' side extends the usable life of the gauge by compensating for contact surface wear, delaying the point at which recalibration or replacement is required. Which materials is the gauge made from? The gauge is manufactured from hardened steel, selected to provide resistance to wear and stable reference dimensions under routine workshop use. Is the gauge suitable for production floor use? Yes. The go/no-go design and rugged construction make this plug gauge appropriate for frequent checks on the production floor and at inspection stations. What identifier should be quoted when ordering or requesting spare parts? Please quote the article number MS911.202 and the Filetta brand designation when placing orders or enquiring about replacements. Manufacturer / Responsible: Schut Geometrische Meettechniek bv; Duinkerkenstraat 21; 9723 BN Groningen; The Netherlands; +31 50 5877877; schutnl@schut.com

Take advantage of DIN 7162 conformity, hardened steel construction and the integrated wear allowance on the go side for dependable bore verification. Order this limit plug gauge directly via Metav Werkzeuge or contact our consultants for application advice. Limit plug gauge G7 – 20 mm, hardened steel (DIN 7162) by Filetta A limit plug gauge G7 designed for rapid go/no-go checks of cylindrical bores in production and inspection environments Hardened steel for long service life Manufactured to DIN 7162 standard Wear allowance on the go side Suitable for bore verification and QC Reliable measurements through recognised standards The gauge is manufactured to DIN 7162, which ensures consistent dimensions and interchangeability across inspection routines. For a nominal size of 20 mm, the plug gauge provides an immediate go/no-go decision, eliminating lengthy measurement evaluation processes. This standard-led approach supports efficient quality control, reduces scrap rates and shortens inspection cycles by delivering clear, repeatable outcomes at every station. Durable construction that reduces downtime Made from hardened steel, the instrument tolerates repeated use on the shop floor while maintaining dimensional stability. The incorporated wear allowance on the go side compensates for gradual material loss during routine checking, extending the service life before any rework or replacement becomes necessary. This pragmatic design reduces unplanned stoppages and lowers total cost of ownership by keeping maintenance intervals predictable. Practical integration for workshop and production use Sized for common bore checks, the plug gauge is ideal for quick verification during assembly, final inspection or incoming goods control. Its straightforward go/no-go functionality accelerates throughput without requiring complex measuring equipment or extensive operator training. The robust design and adherence to DIN 7162 make it suitable for use in machine shops, tool rooms and quality laboratories where rapid, trustworthy pass/fail decisions are required. Reference: model MS911.182 for ordering and stock enquiries. Contact Metav Werkzeuge for expert advice on integrating Filetta limit plug gauges (DIN 7162) into existing inspection routines and to secure reliable supply from our Emmerich warehouse Technical Data Article number: MS911.182 Material: hardened steel Standard: DIN 7162 Size: 20 mm Facts Diameter: 20 mm Special features Wear allowance on the go side Designed for go/no-go checks Robust hardened-steel construction FAQ What is the primary use of this limit plug gauge? This limit plug gauge is intended for fast go/no-go verification of cylindrical bores, providing a clear pass/fail result for production and inspection tasks. What material is the gauge made from and why does it matter? The gauge is produced from hardened steel, which ensures wear resistance and dimensional stability under frequent use, supporting reliable long-term measurements. Which standard does the product comply with? Manufactured to DIN 7162, the gauge meets recognised dimensional and manufacturing criteria for plug gauges used in industrial quality control. How does the wear allowance affect inspection intervals? The wear allowance on the go side compensates for gradual abrasion, extending useful life and allowing longer intervals between gauge replacement or rework; the item is listed as MS911.182 for ordering and inventory reference. Manufacturer / Responsible: Schut Geometrische Meettechniek bv; Duinkerkenstraat 21; 9723 BN Groningen; The Netherlands; +31 50 5877877; schutnl@schut.com

Taking advantage of a compact mm ↔ inch conversion reference and a workshop‑friendly format reduces calculation time and minimises measurement errors; this conversion table is an efficient aid for machining and metrology tasks. Order supply enquiries can be directed via Metav Werkzeuge for reliable fulfilment and specification advice. mm/inch conversion table by Filetta — Compact conversion reference The mm/inch conversion table is a compact reference sheet for rapid unit conversion between millimetres and inches, intended for use in machining, inspection and workshop settings. *Quick mm ↔ inch conversions at a glance *Compact, workshop‑friendly format *Durable print for regular use *Suitable for metrology and machining Faster conversions, fewer calculation errors A concise, printed conversion reference removes the need for repeated calculations and reduces transcription mistakes during setup and inspection. As a ready‑to‑hand reference, the table shortens cycle times in repetitive tasks and supports consistent results across operators. For processes where quick unit checks are required, the sheet complements digital instruments by providing an immediate, readable conversion between mm and inch, helping teams maintain workflow continuity without interrupting machine cycles. Integrates smoothly into metrology and workshop routines The mm/inch conversion table by Filetta fits naturally into quality control and production environments where mixed unit systems occur. The layout is designed for clear legibility during inspection rounds, enabling faster decision making in calibration, part verification and measurement documentation. In combination with calibrated measuring tools, this reference aids standardised entries in protocols and reduces interpretative errors when cross‑referencing drawings and fixtures, thereby supporting traceable measurement workflows. Compact format built for everyday use The slim, durable format makes the table easy to store at the bench, inside inspection folders or alongside tool trolleys; this promotes frequent use without degradation. Printed for clarity and longevity, the sheet is intended as a practical addition to training kits and workshop handbooks where quick access to mm ↔ inch conversions is required. The product is identified by SKU MS835.164, which simplifies catalogue reference and procurement within established supply chains. Request the Filetta mm/inch conversion table (SKU MS835.164) through Metav Werkzeuge for dependable supply from Emmerich and expert advice on specification and integration Technical data Article number: MS835.164 Product name: mm/inch conversion table Brand: Filetta Purpose: Conversion between mm and inch Facts Units: mm, inch Format: Reference table Physical dimensions: not specified Special features Compact, workshop‑friendly format Durable print suitable for regular use Intended for machining and inspection environments FAQ Is the table suitable for precision metrology use? The Filetta mm/inch conversion table is designed as a quick reference to support precision workflows but does not replace calibrated measuring instruments; it assists with unit interpretation and reduces conversion errors. Which units and ranges does the table cover? The sheet provides direct conversions between millimetres and inches for standard workshop ranges, enabling fast cross‑checks without calculation. Can the conversion table withstand everyday workshop conditions? The table is produced with a durable print and compact format intended for regular use at the bench or in inspection folders, making it suitable for routine workshop environments. Is the table useful for training and documentation? Yes, the reference format is well suited to training situations and documentation packs, helping new staff and trainees to interpret mixed‑unit drawings and measurement protocols. Filetta: Manufacturer / Responsible: Schut Geometrische Meettechniek bv; Duinkerkenstraat 21; 9723 BN Groningen; The Netherlands; +31 50 5877877; schutnl@schut.com