Was prüft man mit einem Grenzlehrdorn?

Take advantage of precise, fast pass/fail checks and robust wear resistance thanks to hardened steel and DIN 7162 conformity; order the matching gauge pins directly via Metav Werkzeuge or contact our consultants for batch and inspection advice. Limit Gauge Pin — hardened-steel inspection pin, 11 mm, DIN 7162 (Filetta) The Limit Gauge Pin is a hardened-steel inspection pin designed for rapid go/no-go checks and routine dimensional control in workshops and inspection benches, compliant with DIN 7162. Hardened-steel construction for long service life Conforms to DIN 7162 for consistent tolerances 11 mm nominal diameter for standard inspection tasks Wear allowance on the good side to extend usable life Faster, reliable pass/fail inspection for production lines The compact inspection pin delivers quick go/no-go checks that reduce measuring time at control points and on the shop floor. By providing an unequivocal pass or fail condition, the pin supports efficient decision-making in both single-piece inspections and repetitive sampling routines. Conformity with DIN 7162 ensures that the nominal diameter and tolerance band are traceable to an established standard, which simplifies integration into existing inspection protocols and statistical process control. Robust build that minimises downtime Thanks to its hardened steel construction the pin withstands repeated contact without rapid degradation, while the specified wear allowance on the good side preserves the functional limit for longer. This translates into fewer replacements, reduced downtime and lower indirect costs from inspection interruptions. The hardened surface also keeps seating and mating surfaces consistent, helping to avoid false rejects that would otherwise increase rework. Practical benefits for inspection benches and gauge sets As a dedicated inspection pin, the component is optimised for quick handling and straightforward verification tasks on inspection benches and assembly jigs. The clear go/no-go characteristic reduces interpretation time for operators and speeds up routine quality checks. For quality managers the result is measurable: quicker throughput at control stations and a more consistent acceptance rate across batches. Traceability and suitability for regular quality workflows Manufactured to industry standard, the pin supports consistent batch-to-batch performance and straightforward inventory management when used in gauge sets or fixed inspection fixtures. The simple geometry and standardised tolerance regime make the item suitable for assembly audits, incoming inspections and periodic verification of tool wear, providing procurement confidence for maintenance and quality teams. Request technical advice or a batch availability check from Metav Werkzeuge in Emmerich to align delivery options with production schedules Technical Data Article number: MS911.173 Name: Limit Gauge Pin Material: hardened steel Standard: DIN 7162 Measurements / Core data Diameter: 11 mm Features / Applications Wear allowance on the good side Hardened for wear resistance Intended for go/no-go inspection tasks Category: gauge pins / inspection pins FAQ What is the nominal diameter of this inspection pin? The inspection pin has a nominal diameter of 11 mm; this specification applies to the Filetta limit gauge pin (SKU MS911.173). Is the pin suitable for go/no-go checks on assembly lines? Yes, the Filetta limit gauge pin is designed for rapid pass/fail checks and is suitable for routine assembly-line and workshop inspections. What material is used and how does it affect service life? The pin is made from hardened steel, which increases wear resistance and extends usable life compared with untreated pins. Which standard governs the pin’s tolerances? Tolerances and dimensions conform to DIN 7162, providing a recognised reference for inspection procedures. How does the wear allowance on the good side affect inspection practice? The specified wear allowance on the good side allows continued use while preserving the functional limit for a longer period, reducing unnecessary replacements Manufacturer / Responsible: Schut Geometrische Meettechniek bv; Duinkerkenstraat 21; 9723 BN Groningen; The Netherlands; +31 50 5877877; schutnl@schut.com

Take advantage of precise, repeatable inspection with a comprehensive set that combines hardened steel durability, fine 0.01 mm graduation and clear transport/storage in a tool trolley with a conformity certificate; order the set directly via Metav Werkzeuge or consult our specialists for application advice. Gauge Pin Set MS910.460 — hardened steel, 0.5–12 mm, Filetta The Gauge Pin Set MS910.460 is a complete inspection kit of precision gauge pins for workshop and production metrology, designed for routine go/no‑go checks, dimensional verification and assembly control Extensive set: 1151 gauge pins 0.5–12 mm Hardened steel for high wear resistance 0.01 mm graduation for precise selection Supplied in trolley with conformity certificate Reliable precision for repetitive inspection This set delivers high precision across a broad micro range, covering 0.5–12 mm with a graduation of 0.01 mm, which supports fine incremental selection during inspection procedures. The measured accuracy of 0.002 mm provides a verifiable basis for routine quality checks and contributes directly to stable production outcomes. Using hardened components reduces wear, so nominal sizes remain consistent over repeated use, limiting rework and saving time in the measurement chain. Designed to streamline workshop workflows Presented as a full kit in a purpose‑fitted tool trolley, the collection of pins is organised in individual plastic containers with size marking for rapid retrieval and immediate traceability. The integrated holders with good/reject indication simplify visual sorting and speed up go/no‑go decisions at the bench. These layout and handling choices reduce operator time per check and improve throughput without compromising measurement reliability. Robust handling with traceable conformity Constructed from hardened steel and supplied with a conformity certificate, the set emphasises longevity and documented quality assurance. Individual containers protect each gauge pin from contamination and damage, while the trolley format supports safe transport and tidy storage. The combination of durable materials and documented conformity helps maintain audit readiness and supports consistent measurement results across shifts. Versatile applications across metrology tasks Suitable for inspection, assembly verification and gauge‑based calibration work, the collection is tailored to routine tasks in production, toolmaking and inspection labs. The fine step size enables close fit control and small‑feature checks, while the extensive count of pins in the set covers a wide range of nominal sizes without the need for multiple purchases. The format is particularly useful where rapid switching between sizes and clear go/no‑go indication are required. For hands‑on advice or to secure the Filetta Gauge Pin Set MS910.460 for a stable inspection routine, contact Metav Werkzeuge — our consultants provide practical application support from Emmerich and ensure timely supply to the workshop. Technical data Article number: MS910.460 Name: Gauge pin set Manufacturer: Filetta Material: hardened steel Set: yes Accessories included: 3x holders with good/reject indicator Supplied: tool trolley with conformity certificate Packaging: pins in individual plastic containers with size marking Facts Measurement range: 0.5–12 mm Measurement increment: 0.01 mm Accuracy (nominal): 0.002 mm Pieces per set: 1151 Weight: 63 kg Dimensions (L×W×H): 670×350×540 mm Special features Hardened steel construction Individual marked containers for each pin Tool trolley delivery for transport and storage Conformity declaration included Holders with go/no‑go indicator included FAQ How fine are the increments in the set? The set provides a 0.01 mm graduation between sizes, enabling fine selection for close tolerance checks with the Gauge Pin Set MS910.460. Is the set suitable for repeated industrial use? Yes, the hardened steel pins and protective individual containers make the filetta gauge pin set appropriate for frequent workshop and production use. Does the delivery include documentation? Delivery includes a conformity certificate; the Gauge Pin Set MS910.460 is supplied with documentation confirming its compliance. Can the set be used for calibration tasks? The wide range and fine graduation allow the set to be used for inspection and informal calibration verification; for certified calibration procedures, refer to your internal quality protocols. What accessories come with the set? The set contains three holders with good/reject indication and all pins are housed in individual marked containers within the supplied trolley. Manufacturer / Responsible: Schut Geometrische Meettechniek bv; Duinkerkenstraat 21; 9723 BN Groningen; The Netherlands; +31 50 5877877; schutnl@schut.com

Take advantage of a durable inspection solution that combines hardened steel construction, DIN 7162 conformity and a built‑in wear allowance on the good side for predictable lifetime performance; order the Filetta limit gauge pin directly via Metav Werkzeuge or contact our consultants for application guidance. Limit gauge pin MS911.175 — hardened steel, DIN 7162 by Filetta The limit gauge pin is a precision plug gauge designed for fast verification of hole diameters and dimensional conformity in production and inspection environments. Hardened steel for durability Conforms to DIN 7162 standard Nominal 13 mm gauge pin Wear allowance on the good side Fast, reliable checks for hole diameters Limit gauge pins serve as a compact and effective tool for rapid go/no‑go assessment of bore diameters and fits. The MS911.175 from Filetta allows straightforward comparison against tolerance limits, reducing the time spent on intricate measurements and lowering the risk of finishing parts that fail inspection. By applying a simple pass/fail principle, this type of gauge pin supports continuous quality control and streamlines in‑process checks, which in turn improves throughput and reduces rework rates on the shop floor. Robust construction with predictable wear behaviour Manufactured from hardened steel, the pin provides a resistant contact surface that tolerates repeated use in production environments. The specified wear allowance on the good side means that the design accounts for gradual surface loss without compromising the verification function; users gain a longer useful service life and more predictable maintenance intervals. This wear concept avoids sudden losses of conformity and simplifies decisions about replacement or recalibration, delivering tangible savings over the component lifecycle. Standards compliance for traceable inspection routines Conformity to DIN 7162 ensures that the gauge pin integrates with existing metrology routines and adheres to recognised dimensioning rules, facilitating consistent documentation and auditability. The simple form factor makes the component easy to store alongside other inspection tools and easy to use during incoming inspections or final part control. With a clear identification such as MS911.175 and manufacturer provenance, the pin is suited for repeatable batch checks and supports a traceable quality management workflow. For precise bore verification from Filetta, contact Metav Werkzeuge for ordering and tailored application advice — Metav Werkzeuge GmbH is available at info@metav-werkzeuge.com or by phone at +49 2822 7131930 to support selection and delivery. Technical data Article number: MS911.175 Manufacturer: Filetta Material: hardened steel Size: 13 mm Standard: DIN 7162 Facts Nominal size: 13 mm Special features Wear allowance on the good side Limit/plug gauge function for go/no‑go checks Category: gauge pins / plug gauges Intended for bore diameter verification FAQ What is the primary use of this limit gauge pin? The limit gauge pin MS911.175 by Filetta is intended for quick go/no‑go checks of hole diameters and basic conformity assessments in production and inspection workflows. Which material is the gauge pin made from? The Filetta gauge pin is made from hardened steel, chosen to provide wear resistance and a stable contact surface for repeated inspections. Does this gauge pin conform to recognised standards? Yes, the component conforms to DIN 7162, which supports consistent dimensional control and integration into documented inspection routines. Manufacturer / Responsible: Schut Geometrische Meettechniek bv; Duinkerkenstraat 21; 9723 BN Groningen; The Netherlands; +31 50 5877877; schutnl@schut.com

Take advantage of a standards‑based inspection tool that pairs hardened steel construction with DIN 7162 conformity and a practical wear allowance on the go side, ensuring reliable pass/fail checks and prolonged service life; order the gauge directly via Metav Werkzeuge or consult our team for application advice. Filetta Limit Plug Gauge G7 – 19 mm, hardened steel (DIN 7162) A Filetta Limit Plug Gauge G7 designed for fast go/no-go verification of 19 mm bores in line with DIN 7162 for consistent production control Hardened steel construction Conforms to DIN 7162 19 mm nominal diameter Wear allowance on the go side Rapid, standards‑compliant inspection that saves time A purpose‑built limit plug gauge provides an immediate quality decision: go/no-go assessment without the need for complex readouts. Conformity with DIN 7162 guarantees the gauge’s dimensions and tolerances match recognised inspection criteria, which accelerates in‑process checks and reduces bottlenecks on the production line. The 19 mm nominal diameter is specified for direct matching to mating bores; using a dedicated gauge for this diameter simplifies sampling plans and shortens cycle time while maintaining clear, auditable acceptance criteria. Robust construction for lasting accuracy Made from hardened steel, the gauge resists wear and maintains geometry across repeated use, which sustains repeatability of results. The design includes a wear allowance on the go side, a planned material margin that can be used to extend the service life before the gauge reaches its limit condition. In practical terms, the wear allowance postpones replacement, lowers lifetime cost, and preserves measurement integrity—critical when inspections are frequent or when a single gauge serves multiple machines or workstations. Easy integration into shop‑floor routines and quality systems The compact, single‑purpose format of this limit plug gauge suits assembly lines, quality control benches and manual inspection jigs. Implementation requires minimal training: the visual or tactile pass/fail outcome reduces interpretation time compared with continuous measuring instruments. For organisations aiming to standardise inspection methods, the gauge fits into existing metrological workflows and documentation. Metav’s position as a precision partner supports straightforward procurement and reliable supply from Emmerich, backed by decades of distribution experience for industrial metrology. Contact Metav Werkzeuge today to confirm suitability and request delivery of the Filetta Limit Plug Gauge G7 (SKU MS911.181); Metav’s advisors in Emmerich will provide practical guidance and rapid fulfilment Technical data Article number: MS911.181 Manufacturer: Filetta Designation: Limit plug gauge G7 Facts Nominal diameter: 19 mm Standard: DIN 7162 Special features Material: hardened steel Wear allowance on the go side Category: gauges / plug gauges / inspection pins FAQ What inspection task is this gauge intended for? The Filetta Limit Plug Gauge G7 (SKU MS911.181) is intended for quick go/no-go verification of 19 mm internal bore dimensions to support routine pass/fail inspection. Which standard does the gauge comply with? This limit plug gauge is manufactured to conform with DIN 7162, ensuring dimensional and tolerance compatibility for standardised checks. How does the wear allowance affect service life? The wear allowance on the go side provides an engineered margin that prolongs usable life by allowing controlled wear before the gauge reaches its limit condition. What material is the gauge made from and why does that matter? The gauge is made from hardened steel, which maintains geometry under repeated use and supports long‑term repeatability of inspection results. Can this gauge be used in automated inspection fixtures? Yes, the solid construction and single‑function geometry of this plug gauge make it suitable for integration into manual and automated fixtures where a 19 mm go/no-go check is required. Manufacturer / Responsible: Schut Geometrische Meettechniek bv; Duinkerkenstraat 21; 9723 BN Groningen; The Netherlands; +31 50 5877877; schutnl@schut.com

Take advantage of the combination of hardened steel construction, DIN 7162 compliance and an integrated wear allowance to ensure dependable go/no-go checks in serial inspection. Order the Filetta limit gauge pin directly via Metav Werkzeuge or request specialist advice for integration into existing inspection routines. Filetta Limit Gauge Pin — hardened steel, DIN 7162 Filetta Limit Gauge Pin designed for pass/fail checking of bores and inspection fixtures in industrial metrology Hardened steel construction to DIN 7162 Precision diameter 2.5 mm Wear allowance on the good side Compatible with go/no-go checking routines Reliable pass/fail checking for production control The limit gauge pin delivers a compact, unambiguous check for bore conformity using a simple go/no-go principle, minimising decision time on the shop floor. Manufactured to DIN 7162, the pin provides a clearly defined acceptance limit that supports reproducible inspections and consistent quality gates. The 2.5 mm diameter is specified to industry tolerances, enabling rapid visual and tactile confirmation without complex set‑ups. This direct verification method reduces downstream rework by catching out-of-tolerance parts at the earliest stage. Durability that reduces downtime and maintenance Constructed from hardened steel, the gauge pin resists wear in continuous use and preserves the inspection boundary over many cycles. The integrated wear allowance on the good side prolongs service life by permitting controlled dressing or replacement procedures while maintaining measurement integrity. Fewer replacements and predictable maintenance intervals lead to improved uptime in production lines and lower total cost of ownership. The robust material choice also supports use in regulated environments where repeatability matters. Simple integration into quality workflows and fixtures The pin is suited for fixtures, plug gauges and measuring rigs where straightforward verification is required. Its compact profile and standardised specification make stock management and fixture design straightforward, helping to keep inspection routines efficient. Clear identification (SKU MS911.161) and adherence to established norms aid traceability in quality records and simplify audits. The component is ideal for workshops and inspection stations seeking a pragmatic, standards-based tool to support routine quality control. Contact Metav Werkzeuge for tailored advice and to source the Filetta limit gauge pin (SKU MS911.161) directly from Emmerich — expert support for specification and delivery is available. Technical Data Article number: MS911.161 Manufacturer: Filetta Type: Limit gauge pin Diameter: 2.5 mm Standard: DIN 7162 Material: hardened steel Special note: wear allowance on the good side Facts Diameter: 2.5 mm Standard: DIN 7162 SKU: MS911.161 Special features Hardened steel construction Wear allowance of the good side Intended for go/no-go checking and plug gauge applications Category: gauges / measuring pins FAQ What material is the gauge pin made from? The Filetta limit gauge pin is manufactured from hardened steel, ensuring wear resistance and stable inspection boundaries (SKU MS911.161). Which standard applies to this gauge pin? Manufactured to DIN 7162, the component fulfils established requirements for limit gauges and supports clear pass/fail decisions. What does the wear allowance mean in practical terms? The wear allowance on the good side allows controlled use and maintenance so the gauge retains its acceptance limit for longer in serial inspections. Can this pin be used in fixture-based inspections? Yes, the pin is suitable for fixture and plug gauge applications where a defined go/no-go limit is required for bore checks. How is the size specified? The pin is specified with a diameter of 2.5 mm and supplied under SKU MS911.161 for unambiguous ordering and traceability. Manufacturer / Responsible: Schut Geometrische Meettechniek bv; Duinkerkenstraat 21; 9723 BN Groningen; The Netherlands; +31 50 5877877; schutnl@schut.com

Take advantage of the combination of DIN 7162 conformity, hardened-steel durability and exact 2.5 mm tolerance control for reliable go/no‑go checking in batch inspection. Order the Filetta limit gauge pins directly via Metav Werkzeuge or consult our specialists for batch supply and enquiries. Grenzlehrdorne — limit gauge pin, 2.5 mm, hardened steel (Filetta) A Grenzlehrdorn by Filetta designed for precision go/no‑go verification and wear‑compensated accept/reject checks in production and inspection environments. 2.5 mm diameter, high repeatability Hardened steel construction for long life Conforms to DIN 7162 standard Wear allowance on the good side Consistent go/no‑go control to speed up inspection The Filetta limit gauge pin offers a compact solution for rapid acceptance testing where dimensional conformity must be checked repeatedly. Manufactured from hardened steel, the pin retains its geometry under frequent use, reducing downtime caused by damaged or worn gauges. The specification to DIN 7162 ensures compatibility with established inspection procedures and simplifies documentation within quality systems. The compact form factor and clear acceptance boundary make the item particularly suitable for small‑part assemblies where a fast pass/fail decision avoids lengthy measuring operations. Durable construction that reduces recalibration frequency Robust material selection and heat treatment give the gauge pin a service life that keeps maintenance intervals low. The hardened surface resists deformation, helping maintain the defined tolerance of 2.5 mm over many cycles. In addition, the built‑in wear allowance on the good side provides an engineered margin so that the gauge indicates wear before part acceptance is compromised. This design choice translates into lower lifecycle costs and fewer process interruptions, supporting steady production throughput and reliable quality control. Integrates with workshop routines and quality documentation Designed as a practical shop tool, the limit gauge pin supports streamlined inspection workflows and clear go/no‑go decisions at the point of assembly or incoming inspection. The simple physical check complements dimensional measurement equipment and is ideal for quick checks on batches or random samples. The product is supplied under the Filetta brand and can be adopted easily into existing inspection plans; traceability is maintained through the SKU MS911.203 for ordering and stock control. The result is a pragmatic balance between measurement certainty and operational efficiency. Contact Metav Werkzeuge for Filetta limit gauge pins (SKU MS911.203) to arrange a batch supply or technical briefing near Emmerich — our specialists will advise on quantities and integration into inspection plans. Technical Data Article number: MS911.203 Product name: Grenzlehrdorne Manufacturer: Filetta Material: gehärterter Stahl Standard: DIN 7162 Facts Diameter: 2.5 mm SKU: MS911.203 Special features Abnutzungsaufmaß der Gutseite (wear allowance on the good side) Intended for go/no‑go verification and pin gauge checks Category: Gauge pins / measuring pins FAQ What is the primary use of these limit gauge pins? The Filetta Grenzlehrdorne are intended for rapid go/no‑go checks and dimensional acceptance testing in production and inspection, providing a quick physical decision on part conformity. Is the material suitable for high‑frequency shop use? Yes; the pins are made from hardened steel, which offers resistance to wear and deformation under frequent use, ensuring consistent pass/fail performance. Does this pin comply with recognised standards? The limit gauge pin conforms to DIN 7162, making it suitable for integration into standardised inspection procedures and quality documentation. How does the wear allowance affect inspection results? The built‑in wear allowance on the good side gives an engineered margin that signals wear before a pin accepts out‑of‑tolerance parts, thereby safeguarding process quality. How can this item be ordered or specified for stock? Order by SKU MS911.203 (Filetta) via Metav Werkzeuge for reliable supply and support with integration into inspection routines. Manufacturer / Responsible: Schut Geometrische Meettechniek bv; Duinkerkenstraat 21; 9723 BN Groningen; The Netherlands; +31 50 5877877; schutnl@schut.com

Take advantage of a compact, standardised gauge that combines hardened steel construction with conformity to DIN 7162 for dependable go/no‑go verification; the built‑in wear allowance on the good side reduces rework and prolongs service intervals. Order the limit plug gauge directly via Metav Werkzeuge or ask our consultants if needed. Grenzlehrdorne — limit plug gauge in hardened steel, DIN 7162 (Filetta) The Grenzlehrdorne is a precision limit plug gauge designed for efficient go/no‑go checks and rapid acceptance testing across workshop and production environments. Hardened steel construction Conforms to DIN 7162 Wear allowance on good side Repeatable acceptance checks that speed up inspection A limit plug gauge of this design provides an immediate pass/fail decision, making go/no‑go verification both fast and unambiguous. Conformity with DIN 7162 guarantees that gauges are produced to a recognised industrial standard, which simplifies incoming inspection routines and reduces interpretation effort. By relying on a standardised gauge, throughput is improved and measurement uncertainty from subjective assessment is minimised, supporting a more efficient quality workflow. Durable construction that lowers lifecycle costs Manufactured from hardened steel, the gauge resists wear under repeated contact and maintains its dimensional stability over many cycles. The specified wear allowance on the good side compensates for gradual surface degradation, preserving functional fit and reducing the frequency of replacements. Fewer gauge changes mean less downtime and lower total cost of ownership for routine inspection tasks, especially in high‑volume production or repetitive quality checks. Practical fit for workshop and production use The compact limit plug gauge suits routine acceptance tasks and bench checks where quick decisions are required. Traceability is straightforward during audits when the article identifier MS911.162 is used in documentation, and the robust finish simplifies handling in busy environments. The gauge is particularly appropriate for verifying internal diameters where a simple, repeatable standard is preferable to time‑consuming measurement setups, thus keeping operations lean and reliable. Contact Metav Werkzeuge for tailored advice and supply of Filetta hardened‑steel limit plug gauges and to discuss the best gauge strategy for production or inspection needs Technical Data Article number: MS911.162 Material: hardened steel Standard: DIN 7162 Feature: wear allowance on good side Product type: limit plug gauge Numbers / Core technical data Nominal size: 3 mm Special features Hardened steel construction Design for go/no‑go verification Conformity to DIN 7162 Built‑in wear allowance on the good side FAQ What is the primary use of this limit plug gauge? The limit plug gauge from Filetta is intended for quick go/no‑go checks and acceptance testing of internal diameters where an unequivocal pass/fail result is required. Which standard does the gauge comply with? Compliance with DIN 7162 ensures the gauge meets established industrial production and inspection criteria. What material is used for the gauge and why does it matter? The gauge is made from hardened steel, which provides wear resistance and dimensional stability under repetitive use. How does the wear allowance affect service life? The wear allowance on the good side prolongs the functional life by compensating for gradual surface wear, maintaining fit for longer before requalification or replacement is required. How can the gauge be identified in documentation? Use the article number MS911.162 for traceability in inspection records and procurement lists. Manufacturer / Responsible: Schut Geometrische Meettechniek bv; Duinkerkenstraat 21; 9723 BN Groningen; The Netherlands; +31 50 5877877; schutnl@schut.com

The combination of hardened steel construction, DIN 7162 conformity and a built‑in wear allowance on the good side provides reliable, repeatable limit checks with low life‑cycle cost; order this limit plug gauge directly via Metav Werkzeuge or consult our specialists for application advice. Limit plug gauge G7 — 7 mm, hardened steel (Filetta) The limit plug gauge G7 is a precision limit gauge designed for rapid go/no‑go verification of bore diameters in production and inspection environments. Hardened steel for lasting dimensional stability Conforms to DIN 7162 for standardised tolerances Wear allowance on the 'good' side for reconditioning Ideal for rapid go/no‑go bore checks Fast, standards‑based inspection to keep throughput steady This limit gauge is manufactured from hardened steel and produced to DIN 7162, ensuring that each check delivers a clear, standards‑based decision: accept or reject. The compact pin form factor enables go/no‑go testing at production stations or in the quality lab with minimal setup time. By using a dedicated limit pin for a specific nominal diameter, process control becomes faster and less error‑prone than repeated measurement and calculation, improving overall line efficiency. Built for durability and easy maintenance The design incorporates an explicit wear allowance on the good side, which preserves functional limits after regrinding and extends service life. This intentional allowance means the pin can be reconditioned rather than replaced when surface wear appears, reducing total cost of ownership and downtime. The hardened surface resists abrasion in routine checks, while the clear distinction of the 'good' and 'no‑go' ends simplifies handling and reduces the risk of incorrect use. Practical fit for shop‑floor quality routines As a limit checking tool, the plug gauge integrates into visual and tactile inspection routines: a clear pass or fail removes ambiguity and accelerates decision loops. The small nominal diameter of 7 mm suits components in mechanical assemblies, hydraulic and pneumatic parts, and small‑bore workpieces where quick verification is required. Lightweight and compact, the gauge is easy to store at point of use and to include in inspection kits, helping standardise checks across operators and shifts. For procurement or technical clarification about Filetta limit plug gauges and availability via Metav Werkzeuge, contact our Emmerich team for tailored advice and stock information Technical data Article number: MS911.169 Brand: Filetta Nominal size: 7 mm Material: hardened steel Standard: DIN 7162 Facts Product type: limit plug gauge (go/no‑go) SKU: MS911.169 Typical application: bore diameter verification Format: pin / plug gauge Special features Wear allowance on the good side for regrinding Conforms to standardised tolerances (DIN 7162) Robust surface hardness for repeated checks FAQ What tolerance standard does this limit gauge follow? The limit plug gauge is manufactured to DIN 7162, which defines the dimensional and tolerance requirements used for standardised go/no‑go gauges. Can the gauge be reconditioned when worn? Yes, the built‑in wear allowance on the good side permits regrinding and requalification so the gauge remains serviceable over a longer period. Is this gauge suitable for quick shop‑floor checks of small bores? Yes, the 7 mm nominal diameter and pin format make the gauge well suited to rapid verification of small bores in production and inspection stations. Which materials is the gauge intended to inspect? The gauge is intended for dimensional verification of bores regardless of the workpiece material; material compatibility depends on the component, not the gauge itself. How is the pass/fail decision presented during inspection? The plug gauge provides an immediate pass/fail result: the go end should enter the bore, while the no‑go end must not, enabling unambiguous acceptance control. Manufacturer / Responsible: Schut Geometrische Meettechniek bv; Duinkerkenstraat 21; 9723 BN Groningen; The Netherlands; +31 50 5877877; schutnl@schut.com