Which advantages does a digital 3-point internal micrometer have over an analogue one?

Precision blind‑hole inspection is facilitated by the combination of a self‑centring three‑point head, carbide measuring faces and an accuracy of ±0.005 mm; order the MS908.663 via Metav Werkzeuge or consult our advisors for specification support. MS908.663 — three‑point internal micrometer with self‑centring head and ±0.005 mm accuracy (Metav IndustryLine) A self‑centring three‑point internal micrometer MS908.663 designed for fast, repeatable measurement of blind holes in workshop and production environments. Self‑centring three‑point measuring head Accuracy ±0.005 mm for repeatable results Carbide measuring faces for long service life Delivered in a protective transport case Precise blind‑hole measurement with minimal operator error The three‑point measuring concept produces a natural centre‑finding action that stabilises the instrument inside a blind hole, reducing eccentricity and operator influence. With an analogue reading of 0.005 mm and an accuracy of ±0.005 mm, this gauge is suited to quality‑critical internal diameter checks where small deviations matter. The vernier‑style scale enables direct mechanical reading without reliance on batteries or electronics, supporting uninterrupted inspections on the shop floor. This combination of mechanical reliability and fine resolution promotes consistent pass/fail decisions during incoming inspection and first‑off checks. Built for demanding workshop use and long‑term repeatability Constructed with carbide measuring faces, the instrument resists wear in daily use and preserves measuring integrity over longer service intervals. The instrument’s physical length of 145 mm and measuring span of 100–125 mm places it in the standard measuring range for general machine‑shop applications, offering a practical balance between reach and rigidity. The robust design and hardened contact surfaces make the micrometer tolerant of routine handling; the supplied protective transport case reduces the risk of damage during storage and transit, keeping calibration stability intact. Practical advantages for process control and inspection routines Using a self‑centring, three‑point internal gauge streamlines internal diameter checks in blind holes, bores and recesses, enabling faster set‑ups at the bench or on the machine. The instrument’s repeatable seating and fine resolution help to reduce scrap and rework by catching dimensional drift earlier in the process. As an analogue instrument it integrates easily into established measurement routines and inspection sheets, while its mechanical simplicity minimises downtime compared with devices that rely on electronics. Typical applications and handling guidance The micrometer is intended for blind‑hole and internal diameter measurements in general engineering, toolroom checks and production quality control. For best results, ensure clean contact surfaces and a stable seating in the bore before taking a reading; the three‑point head will centre itself, but careful alignment reduces measurement scatter. Periodic verification against a gauge block or master ring is recommended to confirm ongoing accuracy and to schedule recalibration when necessary. The instrument’s durability and simple operation make it a practical choice for repetitive internal measurements on ferrous and non‑ferrous components. For reliable blind‑hole inspection with Metav IndustryLine precision, contact Metav Werkzeuge for purchase and expert advice by email at info@metav-werkzeuge.com or by telephone on +49 2822 7131930 Technical data Article number: MS908.663 Name: Three‑point internal micrometer Brand: Metav IndustryLine Type: Analogue internal measuring instrument Numbers / Core technical data Measuring range: 100–125 mm Measuring length: 145 mm Reading / Resolution: 0.005 mm Accuracy: ±0.005 mm Special features / Design Self‑centring three‑point measuring head Carbide measuring faces Delivered in a protective transport case Suitable for blind‑hole (blind bore) measurement FAQ How does the three‑point head help with blind‑hole measurement? The three‑point geometry of the MS908.663 automatically centres inside a blind hole, reducing eccentricity and improving repeatability of internal diameter readings. What level of accuracy and resolution can be expected? The instrument provides a resolution of 0.005 mm with an accuracy of ±0.005 mm, making it suitable for tight tolerance internal checks in production and workshop environments. Is the gauge suitable for frequent workshop use? Yes; the carbide measuring faces and robust mechanical construction are designed for daily inspection tasks and extended service life. Can this micrometer measure other internal features besides blind holes? While optimised for blind holes, the instrument can be used for internal diameter checks, recesses and similar internal features where the three‑point contact can seat reliably. What is included with the instrument on delivery? The MS908.663 is supplied complete with a protective transport case to protect the gauge during storage and transport. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Benefit from the combination of three-point contact stability, a colour touchscreen readout and ISO 17025 traceable calibration to secure reproducible internal measurements in the 10.0–12.0 mm range. Order the Three‑Point Internal Micrometer directly via Metav Werkzeuge or consult our specialists for integration advice. Three‑Point Internal Micrometer — digital instrument with Wireless + USB (Microtech Metrology) The Three‑Point Internal Micrometer is a precision instrument for stable internal diameter measurement in small bores, suitable for quality control and bench metrology in workshops and production. Three-point contact for stable internal measurements Colour 1.5" touchscreen for clear readouts Wireless and USB data output for traceable transfer Delivered calibrated to ISO 17025 with certificate Dependable accuracy where tight tolerances matter The instrument combines a three-point contact measuring head with a high‑precision mechanism to reduce runout and centring error, delivering an accuracy of ±0.004 mm across its measuring span. With a measuring range of 10.0–12.0 mm, this device is aimed at fine internal dimensions where repeatability and a low measurement uncertainty are decisive. The robust contact geometry and confirmed specification make it well suited to small‑bore inspection tasks in component finishing and final inspection workflows, supporting a rational decision process for integrating metrology into production control. Seamless data capture for quality documentation Digital measurement is presented on a Colour 1.5" touchscreen for fast reading and reduced interpretation errors; the unit also provides Wireless and USB data output for direct transfer into SPC systems or inspection software. Combined with the included calibration trace, this workflow supports rapid documentation and traceability. The instrument’s readable display and straightforward data export reduce process steps and the risk of transcription mistakes, promoting efficiency and error‑resilient quality reporting in serial inspection and laboratory environments. Practical design for everyday workshop use A compact measuring head with an extended measuring depth of 154 mm keeps handling comfortable while reaching into bores and recesses. A setting ring is included to simplify zeroing and periodic checks. Delivered fully calibrated to ISO 17025, the micrometer arrives with a formal calibration certificate, providing immediate confidence for compliance audits and internal quality routines. The combination of robust measuring geometry, clear digital feedback and certified calibration supports both operational ease and trustworthy results, reinforcing productive workflows and peace of mind in routine inspections. For traceable high‑precision internal measurement solutions from Microtech Metrology, contact Metav Werkzeuge for ordering and application support — email info@metav-werkzeuge.com or call +49 2822 7131930 Technical Data Article number: 133701210 GTIN: 4061905074202 Manufacturer: Microtech Metrology Numbers Measuring range: 10.0–12.0 mm Measuring depth: 154 mm Accuracy: ±0.004 mm Resolution/readout: 0.0001 mm Special features Digital display: Colour 1.5" touchscreen Data output: Wireless and USB Setting ring: included Delivered calibrated to ISO 17025 with certificate FAQ Is the instrument delivered with a calibration certificate? Yes. The Three‑Point Internal Micrometer from Microtech Metrology is supplied fully calibrated to ISO 17025 and includes the calibration certificate for traceability. What measurement range is covered by this micrometer? The device covers internal diameters from 10.0 to 12.0 mm and is designed specifically for high‑precision work within that span. How is measured data transferred to a PC or quality system? Measurement results can be exported via both Wireless and USB connections, enabling straightforward integration into inspection software and SPC workflows. What advantage does the three‑point contact offer? Three contact points centre in the bore automatically, reducing eccentricity and improving repeatability compared with two‑point methods, which is why this geometry is preferred for small‑bore internal measurements. Can the micrometer reach recessed bores? Yes. The instrument’s 154 mm measuring depth allows access to deeper internal features while maintaining the necessary measurement stability. Manufacturer / Responsible: Microtech, Nizhneyurkovska str., 45a, 04080 Kyiv, Ukraine, tool@microtech.tools

Take advantage of the combination of high accuracy, wireless + USB data transfer and full ISO 17025 calibration with certificate for reliable measurements in precision workshops; order the three-point internal micrometre directly via Metav Werkzeuge or ask our consultants for tailored advice. Three‑Point Internal Micrometre – Digital internal measuring tool with wireless + USB and 1.5" colour touchscreen (Microtech Metrology) The Three‑Point Internal Micrometre is a compact digital instrument engineered for precise internal diameter measurement in small bores and precision components within the micro measurement category. *Digital display: 1.5" colour touchscreen *Wireless and USB data output *ISO 17025 calibrated with certificate *Measuring range 12–16 mm, 0.004 mm accuracy Accurate measurements for micro components Classified in the Micro category (suitable for very compact tasks), this instrument covers a measuring range of 12.0–16.0 mm, offering a practical reach for miniature assemblies and precision parts. The instrument combines a fine resolution of 0.0001 mm with a guaranteed accuracy of ±0.004 mm, which reduces measurement uncertainty and supports reproducible inspection results. Such precision is particularly valuable when inspecting small bores in sub‑assemblies where even slight deviations can affect fit and function. Traceable data capture and delivered calibration Designed for modern production environments, the micrometre provides wireless and USB connectivity for straightforward data transfer into inspection logs and SPC systems. The 1.5" colour touchscreen simplifies reading and setting adjustments on the shop floor, while the supplied setting ring ensures fast zeroing and repeatable reference points. The tool is supplied fully calibrated to ISO 17025 and includes a calibration certificate, enabling formal traceability and immediate use in processes that require accredited measurement results. Ergonomic handling that speeds up inspections The three‑point contact design centres measurement force, improving contact consistency inside bores and reducing operator‑induced variation. The compact format supports single‑hand operation in confined spaces and the intuitive touchscreen speeds routine checks, lowering cycle times and decreasing the likelihood of rework. The included setting ring and clear digital readout combine to make daily inspection routines both ergonomic and efficient. Integration into workshop quality routines With its digital outputs and compact form factor, the device integrates easily into existing inspection stations and handheld workflows. The substantial measuring depth of 230 mm provides versatility when accessing deeper bores or assemblies, while the three‑point mechanism ensures stable centring for reliable interior measurements. Together, these features support a consistent quality chain from initial inspection through to final acceptance. Contact Metav Werkzeuge in Emmerich for a suitability review or to request a quotation for this Microtech Metrology three‑point internal micrometre with ISO 17025 calibration; email info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: 133701610 GTIN: 4061905074219 Manufacturer: Microtech Metrology ECLASS: 21170335 Facts Measuring range: 12.0–16.0 mm Resolution: 0.0001 mm Accuracy: ±0.004 mm Measuring depth: 230 mm Special features Digital colour 1.5" touchscreen Data output: Wireless and USB Included setting ring ISO 17025 calibration with certificate Three‑point internal measuring spindle FAQ What bore sizes can be inspected with this instrument? The Three‑Point Internal Micrometre is designed for bores in the 12.0–16.0 mm range and is classified in the micro category for compact internal measurements. Is the micrometre delivered calibrated for traceability? Yes, the instrument is supplied fully calibrated to ISO 17025 and includes a calibration certificate for immediate traceable use. How are measurement results transferred to a PC or inspection system? Measurement data can be transmitted via the micrometre’s wireless interface or exported using the USB connection for integration into inspection logs. What level of precision can be expected during routine checks? Routine measurements with the Three‑Point Internal Micrometre offer a resolution of 0.0001 mm and an accuracy of ±0.004 mm, suitable for high‑precision shopfloor inspections. Does the tool include accessories for initial setup? The micrometre is supplied with an inclusive setting ring to establish a reproducible zero reference and support repeatable measurements. Manufacturer / Responsible: Microtech, Nizhneyurkovska str., 45a, 04080 Kyiv, Ukraine, tool@microtech.tools

Take advantage of the combination of self-centring three-point contact, hardened measuring faces and a protective case for reliable, repeatable blind-bore measurement; order directly via Metav Werkzeuge or request advice from our technical consultants. Three-point internal micrometer MS908.664 — self-centring design, 125–150 mm (Metav IndustryLine) The Three-point internal micrometer MS908.664 is a precision instrument for accurate measurement of blind bores and internal diameters in machine shops and inspection benches Self-centring three-point contact Accuracy ±0.005 mm Hardened measuring faces Supplied in protective case Consistent concentric measurement where it matters The instrument’s self-centring three-point contact mechanism converts small radial differences into a single, centred datum, ensuring high repeatability during blind-bore checks. With a mechanical resolution and accuracy of ±0.005 mm, the device supports tight tolerance verification and process control for internal diameters. This level of precision is particularly useful when comparing series parts or validating internal fits, as the three-point geometry minimises eccentricity and reduces operator-induced variation. Robust construction for repetitive workshop use A durable construction and hardened measuring faces protect the contact points from wear and maintain measurement integrity over prolonged use. The analogue, mechanical drive reduces complexity and avoids battery dependence, making the tool suitable for routine quality inspections on the shop floor. The overall length of 145 mm gives the reach required for its measurement range while keeping the instrument compact enough for stable handling during repeated checks. Ideal balance of reach and stiffness for standard applications Classified in the standard range for internal measurement instruments (125–150 mm), this micrometer offers the best compromise between measuring reach and structural rigidity. That balance is critical in metalworking and fixture assembly, where longer tools can introduce deflection and shorter tools lack coverage. The design is optimised for blind bores, providing reliable access and reproducible contact even when full through-access is not available. Delivered protected and ready for transport The instrument is supplied in a protective case to safeguard measuring faces and the mechanism during transport and storage. Built for regular inspection cycles, it integrates easily into workshop tool sets and measurement benches; its analogue readout is simple to interpret and maintain, supporting efficient quality routines without complex electronic calibration procedures. Contact Metav Werkzeuge for tailored advice on the Metav IndustryLine three-point internal micrometer MS908.664 and to arrange procurement or technical specification support; email info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: MS908.664 Manufacturer: Metav IndustryLine Type: Three-point internal micrometer Feature: Self-centring Measuring range: 125–150 mm Length: 145 mm Accuracy: 0.005 mm Reading: 0.005 mm Mechanism: Analogue Delivery: protective case Measuring faces: hardened Suitable for: blind bores Numeric data Measurement range: 125–150 mm Maximum measurement: 150 mm Minimum measurement: 125 mm Accuracy/resolution: 0.005 mm Length: 145 mm SKU: MS908.664 Design and special features Self-centring three-point contact Hardened measuring faces for wear resistance Analogue drive for low maintenance Compact length for stable handling Supplied in protective case for transport Intended for blind-bore measurement FAQ What measurement range does the instrument cover? The instrument covers a measurement range of 125–150 mm, placing it in the standard workshop range suitable for many machine‑building and metalworking applications; refer to MS908.664 for exact limits. What accuracy and resolution are specified? The device offers an accuracy and reading resolution of 0.005 mm, enabling reliable checks against typical tight tolerance requirements. Is the design suitable for blind bores? Yes — the self-centring three-point contact is engineered specifically to measure blind bores with improved concentricity and repeatability. Are the measuring faces wear-resistant? The measuring faces are hardened to resist wear and maintain consistent contact geometry during repetitive inspection tasks. Is a protective case included? The instrument is supplied in a protective case to secure the micrometer during transport and storage. Is the micrometer digital or analogue? This is an analogue instrument with a mechanical drive and a direct, tactile measuring feel appropriate for workshop environments. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Take advantage of the combination of self‑centring, carbide measuring faces and high repeatability for reliable blind‑hole inspection; the compact 20–25 mm range is ideal for fine mechanical and precision engineering tasks. Order the instrument directly via Metav Werkzeuge or request specification advice from our consultants. Three‑point internal micrometer MS908.655 — self‑centring, carbide measuring faces (20–25 mm) by Metav IndustryLine The Three‑point internal micrometer MS908.655 is a self‑centring internal measuring instrument designed for accurate measurement of blind holes in precision engineering and workshop environments, offering an analogue reading with fine resolution for repeatable results Self‑centring three‑point mechanism Carbide measuring faces for wear resistance Measurement accuracy 0.004 mm Compact range 20–25 mm for fine parts Precise blind‑hole measurement with minimal setup The instrument delivers high repeatability through its self‑centring three‑point mechanism, which ensures concentric contact inside blind bores without complex alignment. With a rated accuracy of 0.004 mm and an analogue reading of 0.005 mm, the device is engineered for tasks where micrometre‑level certainty matters; this combination reduces rework and measurement uncertainty in small components. The compact design is especially suited to micro fabrication and precision inspection of housings and bores. Durable contact faces and dependable mechanical operation Carbide contact faces provide excellent wear resistance, maintaining measurement integrity over extended use in workshop conditions. The analogue nonius construction offers tactile feedback preferred in many inspection routines and requires no batteries or electronic interfaces, supporting uninterrupted operation on the shop floor. The included adjustment ring (25) enables straightforward zeroing and fine setting, while the robust build keeps the mechanical play to a minimum for consistent results. Designed for micro‑range quality control and fine parts Classified in the micro range (suitable for 10–100 mm scales), the 20–25 mm span targets small‑format parts such as precision sleeves, bearing bores and microassemblies. Its compact dimensions and precise geometry make it practical for use in bench inspection and in‑process checks where access is restricted. The measuring faces and frame geometry have been selected to balance stiffness and accessibility, ensuring stable measurements even when handling delicate components. Integration into workshop procedures and traceability The analogue three‑point gauge complements digital and traditional inspection tools as part of a consistent metrology chain; repeatable manual results simplify tolerance checks and go/no‑go decisions. Further technical documentation and measurement data are available from Metav Werkzeuge for integration into QA processes and production control. For operators transitioning from standard calipers or bore gauges, the instrument provides a clear step up in concentricity control without introducing complex electronics. For specification advice or to secure the MS908.655 from Metav IndustryLine, contact Metav Werkzeuge for personalised guidance at info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: MS908.655 Manufacturer: Metav IndustryLine Product: Three‑point internal micrometer Numbers / Core technical data Measuring range: 20–25 mm Reading / resolution: 0.005 mm Accuracy: 0.004 mm Length: 90 mm Special features / Materials Self‑centring three‑point mechanism Carbide measuring faces Analogue nonius scale Suitable for blind‑hole measurement FAQ What measuring range does the MS908.655 cover? The MS908.655 covers a measuring range of 20–25 mm, making it suitable for small bores and fine mechanical components. How precise is the instrument for repeatable checks? The three‑point internal micrometer achieves a stated accuracy of 0.004 mm with an analogue reading of 0.005 mm, designed for consistent bench and in‑process inspection. Are the measuring faces wear resistant? Yes, the contact faces are made of carbide, providing enhanced wear resistance and long‑term dimensional stability for routine use. Is the gauge suitable for blind‑hole applications? The instrument is explicitly intended for blind‑hole measurement, featuring a self‑centring mechanism that ensures concentric contact within such bores. Does Metav IndustryLine provide technical support for integration into QA procedures? Metav IndustryLine and Metav Werkzeuge can supply further technical documentation and advice to assist with integration of the MS908.655 into quality control workflows. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Compact, self‑centring three‑point internal micrometre with a 6.0–8.0 mm measuring range and high mechanical resolution; the MS908.650 combines precise blind‑hole measurement with hardened measuring faces and a fine 0.001 mm reading—Order the three‑point internal micrometre directly via Metav Werkzeuge or ask our consultants if needed Three‑point internal micrometre MS908.650 — self‑centring, 6.0–8.0 mm range Three‑point internal micrometre MS908.650 delivers reliable blind‑hole measurement for precision workshops and production lines Self‑centring three‑point contact Measuring range 6.0–8.0 mm Resolution 0.001 mm reading Hardened measuring faces (HM) Precision where blind‑hole bores matter The self‑centring three‑point contact mechanism ensures coaxial alignment inside blind holes, reducing measurement variability compared with two‑point probes. With a measuring range of 6.0–8.0 mm and an analogue vernier controlled fine adjustment, this instrument is optimised for small‑diameter bores where repeatability is critical. The device’s geometry minimises radial play so that each measurement reflects the actual bore diameter rather than positioning error, which is particularly valuable in small‑component assembly and quality control workflows. Exceptional reading and repeatability for workshop standards Equipped with a mechanical reading division of 0.001 mm, the instrument offers a fine visual resolution while the stated accuracy of ±0.004 mm provides a clear performance expectation for routine inspections. The analogue vernier design gives tactile feedback during measurement, enabling experienced operators to control contact force intuitively. This combination of high resolution and guaranteed accuracy supports process control in machining and metrology tasks where small deviations can affect assembly fit or functional tolerances. Durable contact faces for industrial use The micrometre is fitted with hardened measuring faces (HM) to withstand repeated contact with workpiece surfaces and abrasive contaminants found in production environments. These robust faces preserve the geometry of the contact points over long service intervals, which reduces drift and the need for frequent re‑profiling. In practice, hardened faces extend usable life and maintain measurement integrity when inspecting ferrous and non‑ferrous components during serial production. Designed for blind‑hole measurement and simple handling Specifically configured for blind‑hole bores, the three‑point contact and compact body (length 54.5 mm) permit access to confined features that larger gauges cannot reach. The instrument includes an adjustment ring (setting ring 6) that allows controlled extension of the contact arms, making it suitable for varied hole depths within the stated range. Its compact, mechanically driven construction requires no batteries and integrates easily into inspection benches, making it a practical choice for laboratories and on‑shop measuring stations where robustness and low maintenance are priorities. Contact Metav Werkzeuge today to discuss how the MS908.650 can be integrated into existing inspection routines or to request tailored advice from our technical consultants Technical data Article number: MS908.650 Manufacturer: Metav IndustryLine Type: Three‑point internal micrometre Facts Measuring range: 6.0–8.0 mm Length: 54.5 mm Reading increment: 0.001 mm Accuracy: ±0.004 mm Adjustment ring: 6 Special features Self‑centring three‑point contact Hardened measuring faces (HM) Analogue vernier reading Suitable for blind‑hole bores Category: Messschrauben FAQ What measurement range does this instrument cover? The MS908.650 covers a measuring range of 6.0–8.0 mm, optimised for small blind‑hole bores. Is the device suitable for repetitive production checks? Yes, the MS908.650 is designed for workshop and production use with hardened measuring faces and a robust three‑point contact that supports repeatable inspections. What level of accuracy and resolution can be expected? The instrument provides a reading increment of 0.001 mm and a stated accuracy of ±0.004 mm, suitable for demanding quality control tasks. Can the micrometre measure deep blind holes? The compact length (54.5 mm) and the adjustment ring (6) make the MS908.650 appropriate for many blind‑hole depths within its 6.0–8.0 mm range. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Benefit from precise three-point contact, a self-centring mechanism and an accuracy of 0.005 mm for reliable blind‑hole measurement; order the MS908.661 directly via Metav Werkzeuge or ask our consultants for application advice. Three‑point internal micrometer MS908.661 — 75–88 mm range, self‑centring (Metav IndustryLine) The Three‑point internal micrometer MS908.661 offers a compact, mechanically robust solution for accurate measurement of blind bores between 75 and 88 mm, combining repeatable contact geometry with workshop‑grade durability. Self‑centring three‑point contact Measuring range 75–88 mm Accuracy 0.005 mm Precise three‑point geometry for repeatable blind‑hole results The instrument employs a three‑point contact arrangement that engages the bore at equidistant positions, producing consistent centring and minimising eccentricity in blind‑hole measurements. With a specified accuracy of 0.005 mm and a reading increment of 0.005 mm, the mechanical design prioritises repeatability and straightforward interpretation of results. This focus on measurable performance supports quicker decision‑making on the shop floor and reduces the likelihood of rework caused by inconsistent bore centring. Robust construction and easy handling for daily use Built for persistent use in production and inspection areas, the gauge features hardened measuring faces and an analogue measuring mechanism that requires no batteries. The compact body (length 114 mm) and an adjustable setting ring (87) provide tactile control during measurement operations. Hardened contact surfaces extend service life under typical workshop conditions, while the analogue format keeps the instrument immediately usable without electronic maintenance. The combined effect is low‑maintenance operation with dependable mechanical accuracy. Practical suitability and workflow benefits Designed specifically for blind‑hole applications, the tool is suited to toolrooms, maintenance shops and quality control benches where internal diameters must be checked quickly and reliably. The self‑centring action reduces setup time and helps standardise measurement procedures across operators, improving throughput and traceability. As a purely mechanical gauge it integrates easily with established inspection routines and supports rapid pass/fail decisions without additional calibration steps beyond routine verification. Quality assurance and provenance that support procurement Supplied under the Metav IndustryLine umbrella, the instrument represents a balance of functional precision and workshop pragmatism. Choice of a mechanically driven, three‑point internal gauge is a rational investment when repeatability and simple operation are priorities. Metav’s approach to product selection and distribution provides transparency and supply reliability for industrial buyers who prioritise consistent measurement outcomes. For technical availability and procurement of the MS908.661 three‑point internal micrometer, contact Metav Werkzeuge for product guidance and stock information at info@metav-werkzeuge.com or by phone on +49 2822 7131930 Technical data Article number: MS908.661 Name: Three‑point internal micrometer Manufacturer: Metav IndustryLine Core specifications Measuring range: 75–88 mm Accuracy: 0.005 mm Reading increment: 0.005 mm Length: 114 mm Setting ring: 87 Special features Self‑centring three‑point contact Hardened measuring faces Analogue measuring mechanism Suitable for blind‑hole bores Category: Micrometers FAQ What measuring range does this instrument cover? The MS908.661 covers a measuring range of 75–88 mm and is therefore suited to medium‑sized internal diameters such as blind bores in assemblies. How precise is the measurement? Precision is stated as 0.005 mm with a reading increment of 0.005 mm, which ensures repeatable results for standard workshop inspection tasks. Why is three‑point contact advantageous for blind holes? Three‑point contact centres the gauge automatically within the bore, reducing eccentricity and improving repeatability compared with single‑point internal probes. Where is this instrument typically used? This analogue internal micrometer is used in toolrooms, maintenance workshops and quality control where robust, battery‑free measurement of blind bores is required. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Take advantage of a compact, self-centring three-point measuring head and 0.004 mm accuracy to inspect blind bores with confidence; the instrument’s fine graduations and carbide measuring faces ensure repeatable results in precision workshops. Order directly via Metav Werkzeuge or consult our specialists for application advice. Three-point internal micrometer MS908.651 — self-centring three-point head, 8.0–10.0 mm range (Metav IndustryLine) A three-point internal micrometer designed for precise measurement of blind bores in fine mechanical and workshop environments Self-centring three-point head Carbide measuring faces for durability 0.004 mm measurement accuracy 0.001 mm reading increment Precision engineered for blind-bore measurement The compact three-point design centres automatically on the bore, so alignment errors are reduced and repeatability improves for series checks. The instrument combines a finely graduated analogue spindle with a 0.001 mm reading increment and a verified measurement accuracy of 0.004 mm, which supports quality-controlled machining and inspection routines. This level of reproducibility is particularly valuable when measuring short, deep blind bores where radial run-out and offset would otherwise distort results. Durable contact surfaces and compact ergonomics for workshop use Carbide-tipped measuring faces give long service life under frequent contact and resist wear from abrasive contaminants, maintaining measurement integrity over time. The micrometer’s compact form — overall length 54.5 mm — places it in the micro class for instruments intended for extremely compact, fine‑mechanical tasks; the short, stiff geometry helps to keep handling-induced deflection to a minimum and is ideal for toolrooms, gauges and precision workshops where space and access are limited. Simple analogue operation that integrates with quality processes As an analogue instrument with a clear mechanical spindle, the device delivers tactile feedback and fast, direct readings that can speed up routine inspections without reliance on batteries or electronics. The self-centring action and carbide faces reduce setup time and scrap, while the fine reading increment enables informed pass/fail decisions at the bench. For traceable documentation, the micrometer’s technical values support incorporation into existing inspection protocols and measurement logs. Enquire with Metav Werkzeuge for tailored application advice or to procure the Metav IndustryLine three-point internal micrometer MS908.651 for precision blind‑bore inspection Technical data Article number: MS908.651 Type: Three-point internal micrometer Manufacturer: Metav IndustryLine Facts Measurement range: 8.0–10.0 mm Minimum range: 8.0 mm Maximum range: 10.0 mm Accuracy: ±0.004 mm Reading increment: 0.001 mm Length: 54.5 mm Special features Self-centring three-point head Carbide measuring faces Analogue operation Setting ring: 8 Suitable for blind bores FAQ What measurement range does the instrument cover? The MS908.651 covers a range of 8.0–10.0 mm for internal measurements. How precise is the three-point internal micrometer? The instrument provides a measurement accuracy of ±0.004 mm with a reading increment of 0.001 mm. Are the measuring faces wear-resistant? Yes, the measuring faces are carbide tipped to ensure long-term durability and consistent contact behaviour. Is the device suitable for routine workshop checks of blind bores? The three-point centring head and compact geometry make the MS908.651 well suited to routine blind-bore inspections in toolrooms and precision workshops. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com