Which tariff code applies to a limit plug gauge with h7 fit?

Take advantage of accurate diameter checks, a compact 0.5–10 mm range and robust steel construction to streamline drill verification in the workshop. Order the item directly via Metav Werkzeuge or consult our specialists for tailored advice. Drill Gauge MS910.501 — steel drill gauge, 0.5–10 mm range The Drill Gauge MS910.501 is a compact steel gauge designed for rapid identification and verification of drill diameters in workshop, tooling and inspection environments. Robust steel construction Measuring range 0.5–10 mm Steps every 0.1 mm for quick checks Compact size ideal for micro measurements Fast, reliable diameter checks that speed up inspection The instrument enables immediate validation of drill sizes, offering a measuring range of 0.5–10 mm with clear, regular increments of 0.1 mm for fast go/no-go decisions. This makes the tool particularly effective when time is critical: operators spend less time searching for the right drill and more time on machining. The compact form factor supports quick handling at the bench or next to a machine, reducing workflow interruptions and improving throughput. Built for repeatable precision and easy interpretation Constructed from steel for consistent dimensional stability and wear resistance, the gauge provides repeatable checks across many cycles of use. The regular step spacing simplifies visual comparison between the tool and the corresponding gauge slot, which is especially useful when a production line requires fast sampling rather than laboratory-level metrology. The simple mechanical design avoids electronics, so operation remains straightforward and maintenance demands are minimal while preserving dependable performance. Suited to micro work and small-scale quality control With its maximum measuring range of 10 mm, the gauge is classified in the micro category—ideal for fine mechanical and watchmaking tasks as well as routine checks in general machining where small-diameter drills are common. The tool supports quick decision-making during setup and run-time inspections, contributing to consistent part quality and fewer tool-change mistakes. Where traceable calibration is required, consultancy on calibration options can be provided to match workshop quality routines. Contact Metav Werkzeuge for procurement details, calibration options and application advice on the Filetta Drill Gauge MS910.501 — direct supply from Emmerich to the workshop bench. Technical data Article number: MS910.501 Manufacturer: Filetta Type: Drill gauge Facts Measuring range: 0.5–10 mm Step size: 0.1 mm Minimum: 0.5 mm Maximum: 10 mm Special features Material: Steel Application: Drill diameter verification Category: Gauges / Measuring pins FAQ What measuring range does this gauge cover? The gauge covers a range from 0.5 mm to 10 mm, making the Drill Gauge MS910.501 suitable for small-diameter drill checks. How fine are the increments on the gauge? Increments are 0.1 mm, which allows for quick visual checks and straightforward go/no-go comparison when verifying drill diameters. Is the gauge suitable for workshop use or only for metrology labs? Designed for practical workshop use, the Filetta drill gauge provides robust, repeatable checks ideal for bench and production environments. What material is the gauge made from? The gauge is made from steel, selected for dimensional stability and wear resistance under regular inspection cycles. Can the gauge be used during machine setup? Yes, the compact size and clear steps make the MS910.501 convenient for use during machine setup and routine sampling inspections. Manufacturer / Responsible: Schut Geometrische Meettechniek bv; Duinkerkenstraat 21; 9723 BN Groningen; The Netherlands; +31 50 5877877; schutnl@schut.com

Take advantage of the proven combination of hardened steel construction, DIN 7162 conformity and a clear 10 mm diameter for reliable pass/fail inspection in series production. Order the limit gauge pin directly via Metav Werkzeuge or ask our consultants if needed. Limit Gauge Pin MS911.214 — hardened steel, 10 mm, DIN 7162 A Limit Gauge Pin MS911.214 for fast, repeatable go/no-go checks in workshop and production quality control. Hardened steel construction DIN 7162 compliant 10 mm diameter precision Wear allowance on the go side Consistent pass/fail decisions through standardised geometry The MS911.214 delivers decisive, repeatable results for quick acceptance checks thanks to its precisely ground 10 mm diameter and adherence to DIN 7162. The standardised geometry removes ambiguity in go/no-go inspection and shortens cycle times in quality control routines. As a hardened pin gauge, it is optimised for frequent handling and simple visual verification, so inspection processes become more efficient without added complexity. Robust material and defined wear allowance extend service life Manufactured from hardened steel, the pin resists surface deformation and maintains dimensional stability under continuous use. The specified wear allowance on the go side provides a clearly defined margin for maintenance planning: when the allowable wear is reached, replacement is recommended to preserve measurement integrity. This predictable wear behaviour supports inventory planning and minimises unplanned downtime on the production floor. Practical benefits for workshop and metrology benches Designed for compact and repetitive checks, this limit pin reduces setup time and supports fast inline verification. The simple construction means no electronics or adjustment are required, while the conformity to established standards facilitates integration into existing inspection procedures. For medium- to high-volume verification tasks, the pin contributes to stable quality indicators and easier compliance documentation. For reliable availability and expert advice on Filetta limit gauge pins, contact Metav Werkzeuge in Emmerich — our team can advise on stocking, batch inspection strategies and alternatives for specific applications Technical data Article number: MS911.214 Name: Limit Gauge Pin (Grenzlehrdorne) Manufacturer: Filetta Facts Diameter: 10 mm Material: hardened steel Standard: DIN 7162 Special features Wear allowance on the go side Category: Gauges, Pin gauges Intended use: Pass/fail inspection FAQ What is the primary use of this limit pin? The Limit Gauge Pin MS911.214 is intended for quick go/no-go checks and simple pass/fail inspections of hole diameters and similar features in production and workshop environments. Which standard does the pin conform to? Conformity to DIN 7162 ensures the pin's geometry and tolerances meet recognised metrology requirements for pin gauges. What material is used for the pin and why does it matter? The pin is made of hardened steel, which provides wear resistance and stable dimensions during repeated use, helping to maintain inspection reliability. How does the wear allowance affect maintenance? The specified wear allowance on the go side defines when the pin should be replaced to ensure continued measurement integrity and to avoid accepting out-of-tolerance parts. Is this pin suitable for automated inspection stations? Yes. The simple, robust design and standardised dimensions of the MS911.214 enable integration into automated fixtures or manual verification processes where a fixed go/no-go criterion is required. Manufacturer / Responsible: Schut Geometrische Meettechniek bv; Duinkerkenstraat 21; 9723 BN Groningen; The Netherlands; +31 50 5877877; schutnl@schut.com

Limit gauge pins in hardened steel with DIN 7162 conformity and a defined wear allowance ensure reliable go/no-go checking for serial inspection; their compact 10 mm size and robust finish support repeatable measurements across production batches. Order these gauges directly via Metav Werkzeuge or consult our specialists for matching sets and delivery options. Limit gauge pins — hardened steel, DIN 7162 (Filetta) Limit gauge pins for quick go/no-go checking in machining and quality control, designed for repetitive use in workshop and production environments Hardened steel construction DIN 7162 compliant gauging Wear allowance on go side Compact 10 mm diameter Faster, standard-compliant checking for routine quality control The compact gauge pins are engineered for efficient tactile inspection in production. Made from hardened steel, the pins provide a hard-wearing contact surface that resists deformation during repeated use, which reduces rework and inspection downtime. Conformity with DIN 7162 gives a clear normative basis for acceptance testing, so batch checks and go/no-go decisions can be performed with confidence and traceability. The 10 mm dimension ensures compatibility with common bore sizes and gauge holders. Built for longevity with a wear-compensating design A defined wear allowance on the go side extends service life by allowing controlled material loss before replacement is required. This practical design reduces the frequency of recalibration cycles and keeps inspection throughput steady. Precision-ground tips maintain small contact radii for consistent engagement, while the hardened core resists flattening under repeated contact. The result is lower total cost of ownership and predictable maintenance planning. Practical handling and system integration in the workshop The pins are suited to bench gauges, nested holders and manual gauge sets commonly used in metalworking and tool shops. Their compact format and standardised dimensions permit quick swapping and straightforward storage in standard test sets. Where a go/no-go decision is required on an assembly line, these gauge pins accelerate the process and reduce operator uncertainty, supporting both throughput and quality assurance procedures. What to expect from specification and suppliers Manufactured by Filetta, the pins are supplied according to the stated standard and are suitable for routine inspection tasks where a robust, standardised check is required. The product designation and item number simplify reordering: reference MS911.172 for consistent procurement. For those seeking gauge sets or matched pairs, speak with our advisors to confirm tolerances and any special surface finish requirements. Contact Metav Werkzeuge for tailored set configuration or immediate dispatch from Emmerich — our specialists will advise on matching gauges and delivery options Technical data Article number: MS911.172 Product: Limit gauge pins Manufacturer: Filetta Material: hardened steel Standard: DIN 7162 Facts Diameter: 10 mm SKU: MS911.172 Special features Wear allowance on go side Precision-ground tip Category: Measuring gauges — gauge pins Suitable for repetitive go/no-go checking FAQ What material are the pins made from? The pins are manufactured in hardened steel, providing a durable contact surface for repeated gauging. Which standard applies to these gauge pins? These gauge pins conform to DIN 7162, ensuring standardised dimensions and acceptance criteria for go/no-go checks. What does the wear allowance on the go side mean? The wear allowance provides controlled material allowance on the go side so the pin remains within acceptance limits for a defined period before replacement is necessary. Can these pins be used for common bore checks? Yes — the compact 10 mm diameter is intended for typical bore and hole checks and integrates with standard holders and sets. How should the pins be referenced when reordering? Use the item number MS911.172 and the manufacturer name Filetta to ensure identical replacement parts are supplied. Manufacturer / Responsible: Schut Geometrische Meettechniek bv; Duinkerkenstraat 21; 9723 BN Groningen; The Netherlands; +31 50 5877877; schutnl@schut.com

Benefit from the combination of hardened steel construction and conformity to DIN 7162 for repeatable internal diameter checks; the 15 mm nominal size offers a direct fit for standard bores. Order the limit plug gauge directly via Metav Werkzeuge or consult our specialists for application advice. Limit plug gauge – 15 mm, hardened steel (Filetta) Limit plug gauge for quick go/no-go verification of internal diameters in production and inspection Hardened steel construction Compliant with DIN 7162 standard 15 mm nominal diameter gauge Wear allowance on master side Precision inspection where it matters The limit plug gauge is designed for fast and reliable verification of internal bores in routine quality checks. Manufactured from hardened steel, the gauge offers mechanical resilience that reduces wear and maintains form under repeated use. Conformity with DIN 7162 ensures that the gauge fits established acceptance procedures and inspection protocols, simplifying integration into existing quality workflows. As a result, production lines gain a compact, low-effort control tool that supports consistent pass/fail decisions. Durability and traceable performance A clear technical advantage of this gauge is the incorporated wear allowance on the master side, which prolongs usable life and offers predictable wear behaviour. The material choice—hardened steel—provides resistance to deformation and abrasion, reducing dimensional drift during frequent checks. For workshops and inspection rooms that require robust tools rather than disposable checking aids, this construction translates into fewer replacements and stable measurement outcomes over time, supporting reliable component acceptance. Simple handling for reliable results The gauge’s nominal 15 mm size and compact form factor make it suitable for rapid in-process checks and bench inspection tasks in metalworking and assembly. As a limit gauge, it provides unambiguous go/no-go feedback without needing additional measurement devices, speeding up throughput while keeping control simple. The Filetta item (Article number MS911.177) is particularly suited to operators who prioritise straightforward inspection methods and durable tooling that aligns with recognised standards. For reliable acceptance testing and long-term workshop use, request the Filetta limit plug gauge from Metav Werkzeuge—technical advice and supply are available via info@metav-werkzeuge.com or by phone on +49 2822 7131930 Technical data Article number: MS911.177 Name: Limit plug gauge Brand: Filetta Facts Diameter: 15 mm Standard: DIN 7162 Special features Material: hardened steel Application: internal diameter verification (plug gauge) Special feature: wear allowance on master side Category: Gauges (Measuring instruments > Gauges) FAQ What is the intended use of this limit plug gauge? The limit plug gauge is intended for go/no-go checks of internal diameters in production and inspection; the Filetta gauge MS911.177 verifies whether bores meet the specified acceptance limits. Is the gauge suitable for continuous shop-floor use? Yes, the hardened steel construction of the Filetta limit plug gauge ensures robustness for frequent shop-floor inspections and routine quality control. Which standard does the gauge conform to? The gauge conforms to DIN 7162, meaning it fits standard inspection routines and documented acceptance criteria for plug gauges. Manufacturer / Responsible: Schut Geometrische Meettechniek bv; Duinkerkenstraat 21; 9723 BN Groningen; The Netherlands; +31 50 5877877; schutnl@schut.com

Take advantage of a compact, standardised gauge that combines hardened steel construction with conformity to DIN 7162 for dependable go/no‑go verification; the built‑in wear allowance on the good side reduces rework and prolongs service intervals. Order the limit plug gauge directly via Metav Werkzeuge or ask our consultants if needed. Grenzlehrdorne — limit plug gauge in hardened steel, DIN 7162 (Filetta) The Grenzlehrdorne is a precision limit plug gauge designed for efficient go/no‑go checks and rapid acceptance testing across workshop and production environments. Hardened steel construction Conforms to DIN 7162 Wear allowance on good side Repeatable acceptance checks that speed up inspection A limit plug gauge of this design provides an immediate pass/fail decision, making go/no‑go verification both fast and unambiguous. Conformity with DIN 7162 guarantees that gauges are produced to a recognised industrial standard, which simplifies incoming inspection routines and reduces interpretation effort. By relying on a standardised gauge, throughput is improved and measurement uncertainty from subjective assessment is minimised, supporting a more efficient quality workflow. Durable construction that lowers lifecycle costs Manufactured from hardened steel, the gauge resists wear under repeated contact and maintains its dimensional stability over many cycles. The specified wear allowance on the good side compensates for gradual surface degradation, preserving functional fit and reducing the frequency of replacements. Fewer gauge changes mean less downtime and lower total cost of ownership for routine inspection tasks, especially in high‑volume production or repetitive quality checks. Practical fit for workshop and production use The compact limit plug gauge suits routine acceptance tasks and bench checks where quick decisions are required. Traceability is straightforward during audits when the article identifier MS911.162 is used in documentation, and the robust finish simplifies handling in busy environments. The gauge is particularly appropriate for verifying internal diameters where a simple, repeatable standard is preferable to time‑consuming measurement setups, thus keeping operations lean and reliable. Contact Metav Werkzeuge for tailored advice and supply of Filetta hardened‑steel limit plug gauges and to discuss the best gauge strategy for production or inspection needs Technical Data Article number: MS911.162 Material: hardened steel Standard: DIN 7162 Feature: wear allowance on good side Product type: limit plug gauge Numbers / Core technical data Nominal size: 3 mm Special features Hardened steel construction Design for go/no‑go verification Conformity to DIN 7162 Built‑in wear allowance on the good side FAQ What is the primary use of this limit plug gauge? The limit plug gauge from Filetta is intended for quick go/no‑go checks and acceptance testing of internal diameters where an unequivocal pass/fail result is required. Which standard does the gauge comply with? Compliance with DIN 7162 ensures the gauge meets established industrial production and inspection criteria. What material is used for the gauge and why does it matter? The gauge is made from hardened steel, which provides wear resistance and dimensional stability under repetitive use. How does the wear allowance affect service life? The wear allowance on the good side prolongs the functional life by compensating for gradual surface wear, maintaining fit for longer before requalification or replacement is required. How can the gauge be identified in documentation? Use the article number MS911.162 for traceability in inspection records and procurement lists. Manufacturer / Responsible: Schut Geometrische Meettechniek bv; Duinkerkenstraat 21; 9723 BN Groningen; The Netherlands; +31 50 5877877; schutnl@schut.com

Combining DIN 7162 conformity, hardened steel construction and a wear allowance on the Go side yields a durable checking tool for repeatable bore inspections; order the gauge directly via Metav Werkzeuge or consult our advisers for application guidance. Limit plug gauge G7 — 3.5 mm, hardened steel (Filetta) Limit plug gauge G7 is a hardened-steel go/no-go gauge designed for rapid acceptance checks of small bores in production and quality control. Hardened steel construction Complies with DIN 7162 standard Wear allowance on the Go side Diameter 3.5 mm precision Reliable checks for small bores The limit plug gauge is intended for fast, unequivocal go/no-go inspections in the workshop and at in‑process control stations. Manufactured to DIN 7162, the tool offers standardised dimensions for consistent interchangeability across gauges and fixtures. With a nominal diameter of 3.5 mm, the gauge pin provides a compact solution for verifying small internal diameters without the need for complex measuring setups, enabling straightforward acceptance decisions and reducing inspection time. Designed to maintain accuracy and lifetime Constructed from hardened steel, the gauge resists wear and mechanical damage during repetitive use, which secures measurement stability over many cycles. The specified wear allowance on the Go side compensates for gradual material loss at the contact zone: this means the initial pass/fail boundary is conservatively set so that the Go end remains reliable as the gauge accumulates wear, thereby extending the service life and reducing replacement frequency. Such design reduces process interruptions and supports predictable maintenance planning. Practical integration into production and inspection routines As a dedicated measuring pin, the device integrates easily into gauge sets, test benches and handheld Go/No‑Go routines; the compact geometry allows quick handling and minimal fixturing. The simple acceptance logic of a limit plug gauge shortens operator training and accelerates throughput in inspection loops, delivering measurable time savings. For specific application scenarios or assistance with fixture compatibility, Metav’s technical advisers can provide pragmatic recommendations tailored to production needs. For standard-compliant bore checks and tailored application advice, order the Filetta limit plug gauge G7 via Metav Werkzeuge or contact our Emmerich team at info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: MS911.163 Manufacturer: Filetta Product: Limit plug gauge G7 Facts Diameter: 3.5 mm Standard: DIN 7162 Special features Material: hardened steel Wear allowance on the Go side Category: gauge pins / measuring pins FAQ What is the primary purpose of this limit plug gauge? The Filetta limit plug gauge G7 (MS911.163) is used for quick go/no-go inspections of small internal diameters to support fast acceptance decisions in production and quality control. Which standard does the gauge comply with? The gauge is manufactured to DIN 7162, ensuring standardised dimensions and compatibility with conventional metrology practices. What material is the gauge made from and why is that important? This limit plug gauge is made of hardened steel, which improves wear resistance and maintains functional tolerances during repetitive use. What does "wear allowance on the Go side" mean in practice? The wear allowance on the Go side means the Go end is dimensioned to allow a controlled amount of wear before it affects pass/fail decisions, extending the gauge’s usable life while preserving inspection reliability. Can this gauge be used on a shop floor for routine checks? Yes, the compact 3.5 mm gauge pin is suitable for routine shop‑floor Go/No‑Go checks and can be incorporated into simple test fixtures or handheld inspection procedures. Manufacturer / Responsible: Schut Geometrische Meettechniek bv; Duinkerkenstraat 21; 9723 BN Groningen; The Netherlands; +31 50 5877877; schutnl@schut.com

Take advantage of the combination of hardened steel construction, DIN 7162 compliance and an integrated wear allowance for consistent pass/fail decisions and extended service life. Order the limit plug gauge directly via Metav Werkzeuge or contact our consultants for specification advice. Limit plug gauge – Filetta, hardened steel, DIN 7162 The Limit plug gauge is a precision go/no-go inspection pin designed for fast dimensional checks of bores and fittings in production and quality control. Hardened steel construction Manufactured to DIN 7162 Wear allowance on the good side Reliable pass/fail checking for fast quality control A compact limit plug gauge provides a straightforward binary decision in inspection routines, turning measurement into an immediate pass or fail. The combination of DIN 7162 conformity and a hardened shaft ensures that the gauge meets recognised geometric and tolerance requirements, which reduces interpretation time in quality control and accelerates throughput on the shop floor. This approach lowers downtime created by uncertain measurements and supports reproducible, traceable inspection results. Built for longevity and repeatable results Constructed from hardened steel, the pin resists abrasion and maintains a stable measuring diameter over many cycles, so calibration intervals can be extended without compromising confidence. The included wear allowance on the good side compensates for normal surface degradation, preserving the functional limit for go checks and reducing the need for immediate replacement. For maintenance planning this translates into predictable lifecycle costs and less frequent tool changeovers. Easy integration into workshop inspection processes Compliance with DIN 7162 means the gauge integrates cleanly into existing inspection plans and can be referenced in control documentation and reports. The simple geometry and compact design facilitate handheld use or fixture mounting, enabling quick comparison checks during in-process inspection or final quality control. The instrument functions as an efficient screening tool before more detailed metrology is applied, saving time while keeping measurement risk low. Suited applications and practical advantages Ideal for routine bore verification and acceptance testing, the gauge is suited to mechanical engineering, component assembly and finishing operations where fast, reproducible decisions are required. The small footprint of the pin makes it convenient in tight work stations and on assembly lines, while the robust material and standardised manufacture support long-term reliability. Where quick verification is needed, the plug gauge acts as a dependable first check. For DIN‑compliant limit gauging and practical advice from our Emmerich quality filter, contact Metav Werkzeuge to order Filetta limit plug gauges or to discuss application-specific recommendations: info@metav-werkzeuge.com / +49 2822 7131930. Technical data Article number: MS911.206 Manufacturer: Filetta Material: hardened steel Standard: DIN 7162 Measurements Size: 4 mm Special features Wear allowance on the good side Category: Gauge pins / plug gauge Application: Pass/fail inspection of bores FAQ What is the primary purpose of this limit plug gauge? The limit plug gauge is intended for quick pass/fail verification of bore diameters and mating features during production and final inspection. Which material is used for the gauge? The Filetta limit plug gauge is made from hardened steel to ensure wear resistance and dimensional stability. Does the gauge comply with any standards? Yes, the gauge is manufactured in accordance with DIN 7162, ensuring standardised geometry and tolerance handling. What size does this article cover? This item is specified with a size of 4 mm and is listed under article number MS911.206. How does the wear allowance affect inspection? The built-in wear allowance on the good side maintains the effective go condition as the surface experiences normal abrasion, thus extending service life while preserving reliable go/no-go decisions. Manufacturer / Responsible: Schut Geometrische Meettechniek bv; Duinkerkenstraat 21; 9723 BN Groningen; The Netherlands; +31 50 5877877; schutnl@schut.com

The combination of hardened steel construction, conformity with DIN 7162, and a clearly defined wear allowance on the good side ensures reliable, repeatable go/no-go verification and long service life; order this gauge pin directly via Metav Werkzeuge or consult the Metav team for application advice. Limit gauge pin G7, 5 mm — Filetta Limit gauge pin for precision go/no-go checks and wear assessment in workshop and inspection environments. Hardened steel construction Conforms to DIN 7162 Wear allowance marked on good side Consistent pass/fail inspection for production routines The robust hardened steel body provides a stable reference surface that resists deformation under repeated use, supporting repeatable inspection results when used for go/no-go checks. Conformity with DIN 7162 gives a recognised benchmark for dimensional behaviour and interchangeability, so inspection processes can be standardised across machines and shifts. This reliability reduces rework, streamlines quality control and shortens inspection cycles in a busy workshop environment. Visible wear allowance aids maintenance planning A clearly indicated wear allowance on the good side makes it straightforward to monitor gauge condition and schedule replacements before limits are exceeded. The marked allowance functions as an operational guide for maintenance teams and enables conservative assessment of gauge life without complex measurement procedures. This feature supports predictable tool management, helping to avoid unexpected inspection failures and maintain traceable measurement practice. Compact form for fixtures and tight spaces With a nominal size of 5 mm, the pin is suited to tight-fixture applications and small-bore verification tasks common in jigs and measuring arrangements. The compact diameter enables use as a precision locating element or measuring pin where access is limited, while the hardened finish sustains surface integrity under frequent contact. As a limit gauge pin, it delivers a focused solution for dimensional control of small components and fit checks within assemblies. For precision go/no-go control rely on Filetta quality—contact Metav Werkzeuge for availability, technical advice and secure delivery to your workshop Technical data Article number: MS911.166 Manufacturer: Filetta Material: hardened steel Standard: DIN 7162 Measurements Nominal size: 5 mm Special features Wear allowance on the good side Category: measuring pins FAQ What is the intended use of this limit gauge pin? The limit gauge pin is designed for go/no-go verification and dimensional checks in workshop metrology; Filetta manufacture it to serve as a precise reference pin for small-bore and fit inspections. How does the wear allowance improve gauge management? A marked wear allowance on the good side provides a visual threshold for service life; when the allowance is reached the pin should be replaced to preserve measurement integrity. Is the product compliant with any standards? Yes, the pin complies with DIN 7162, ensuring standardised dimensional characteristics suitable for industrial inspection routines. Manufacturer / Responsible: Schut Geometrische Meettechniek bv; Duinkerkenstraat 21; 9723 BN Groningen; The Netherlands; +31 50 5877877; schutnl@schut.com