What does a thread limit gauge check?

Take advantage of accurate diameter checks, a compact 0.5–10 mm range and robust steel construction to streamline drill verification in the workshop. Order the item directly via Metav Werkzeuge or consult our specialists for tailored advice. Drill Gauge MS910.501 — steel drill gauge, 0.5–10 mm range The Drill Gauge MS910.501 is a compact steel gauge designed for rapid identification and verification of drill diameters in workshop, tooling and inspection environments. Robust steel construction Measuring range 0.5–10 mm Steps every 0.1 mm for quick checks Compact size ideal for micro measurements Fast, reliable diameter checks that speed up inspection The instrument enables immediate validation of drill sizes, offering a measuring range of 0.5–10 mm with clear, regular increments of 0.1 mm for fast go/no-go decisions. This makes the tool particularly effective when time is critical: operators spend less time searching for the right drill and more time on machining. The compact form factor supports quick handling at the bench or next to a machine, reducing workflow interruptions and improving throughput. Built for repeatable precision and easy interpretation Constructed from steel for consistent dimensional stability and wear resistance, the gauge provides repeatable checks across many cycles of use. The regular step spacing simplifies visual comparison between the tool and the corresponding gauge slot, which is especially useful when a production line requires fast sampling rather than laboratory-level metrology. The simple mechanical design avoids electronics, so operation remains straightforward and maintenance demands are minimal while preserving dependable performance. Suited to micro work and small-scale quality control With its maximum measuring range of 10 mm, the gauge is classified in the micro category—ideal for fine mechanical and watchmaking tasks as well as routine checks in general machining where small-diameter drills are common. The tool supports quick decision-making during setup and run-time inspections, contributing to consistent part quality and fewer tool-change mistakes. Where traceable calibration is required, consultancy on calibration options can be provided to match workshop quality routines. Contact Metav Werkzeuge for procurement details, calibration options and application advice on the Filetta Drill Gauge MS910.501 — direct supply from Emmerich to the workshop bench. Technical data Article number: MS910.501 Manufacturer: Filetta Type: Drill gauge Facts Measuring range: 0.5–10 mm Step size: 0.1 mm Minimum: 0.5 mm Maximum: 10 mm Special features Material: Steel Application: Drill diameter verification Category: Gauges / Measuring pins FAQ What measuring range does this gauge cover? The gauge covers a range from 0.5 mm to 10 mm, making the Drill Gauge MS910.501 suitable for small-diameter drill checks. How fine are the increments on the gauge? Increments are 0.1 mm, which allows for quick visual checks and straightforward go/no-go comparison when verifying drill diameters. Is the gauge suitable for workshop use or only for metrology labs? Designed for practical workshop use, the Filetta drill gauge provides robust, repeatable checks ideal for bench and production environments. What material is the gauge made from? The gauge is made from steel, selected for dimensional stability and wear resistance under regular inspection cycles. Can the gauge be used during machine setup? Yes, the compact size and clear steps make the MS910.501 convenient for use during machine setup and routine sampling inspections. Manufacturer / Responsible: Schut Geometrische Meettechniek bv; Duinkerkenstraat 21; 9723 BN Groningen; The Netherlands; +31 50 5877877; schutnl@schut.com

Take advantage of precise, fast pass/fail checks and robust wear resistance thanks to hardened steel and DIN 7162 conformity; order the matching gauge pins directly via Metav Werkzeuge or contact our consultants for batch and inspection advice. Limit Gauge Pin — hardened-steel inspection pin, 11 mm, DIN 7162 (Filetta) The Limit Gauge Pin is a hardened-steel inspection pin designed for rapid go/no-go checks and routine dimensional control in workshops and inspection benches, compliant with DIN 7162. Hardened-steel construction for long service life Conforms to DIN 7162 for consistent tolerances 11 mm nominal diameter for standard inspection tasks Wear allowance on the good side to extend usable life Faster, reliable pass/fail inspection for production lines The compact inspection pin delivers quick go/no-go checks that reduce measuring time at control points and on the shop floor. By providing an unequivocal pass or fail condition, the pin supports efficient decision-making in both single-piece inspections and repetitive sampling routines. Conformity with DIN 7162 ensures that the nominal diameter and tolerance band are traceable to an established standard, which simplifies integration into existing inspection protocols and statistical process control. Robust build that minimises downtime Thanks to its hardened steel construction the pin withstands repeated contact without rapid degradation, while the specified wear allowance on the good side preserves the functional limit for longer. This translates into fewer replacements, reduced downtime and lower indirect costs from inspection interruptions. The hardened surface also keeps seating and mating surfaces consistent, helping to avoid false rejects that would otherwise increase rework. Practical benefits for inspection benches and gauge sets As a dedicated inspection pin, the component is optimised for quick handling and straightforward verification tasks on inspection benches and assembly jigs. The clear go/no-go characteristic reduces interpretation time for operators and speeds up routine quality checks. For quality managers the result is measurable: quicker throughput at control stations and a more consistent acceptance rate across batches. Traceability and suitability for regular quality workflows Manufactured to industry standard, the pin supports consistent batch-to-batch performance and straightforward inventory management when used in gauge sets or fixed inspection fixtures. The simple geometry and standardised tolerance regime make the item suitable for assembly audits, incoming inspections and periodic verification of tool wear, providing procurement confidence for maintenance and quality teams. Request technical advice or a batch availability check from Metav Werkzeuge in Emmerich to align delivery options with production schedules Technical Data Article number: MS911.173 Name: Limit Gauge Pin Material: hardened steel Standard: DIN 7162 Measurements / Core data Diameter: 11 mm Features / Applications Wear allowance on the good side Hardened for wear resistance Intended for go/no-go inspection tasks Category: gauge pins / inspection pins FAQ What is the nominal diameter of this inspection pin? The inspection pin has a nominal diameter of 11 mm; this specification applies to the Filetta limit gauge pin (SKU MS911.173). Is the pin suitable for go/no-go checks on assembly lines? Yes, the Filetta limit gauge pin is designed for rapid pass/fail checks and is suitable for routine assembly-line and workshop inspections. What material is used and how does it affect service life? The pin is made from hardened steel, which increases wear resistance and extends usable life compared with untreated pins. Which standard governs the pin’s tolerances? Tolerances and dimensions conform to DIN 7162, providing a recognised reference for inspection procedures. How does the wear allowance on the good side affect inspection practice? The specified wear allowance on the good side allows continued use while preserving the functional limit for a longer period, reducing unnecessary replacements Manufacturer / Responsible: Schut Geometrische Meettechniek bv; Duinkerkenstraat 21; 9723 BN Groningen; The Netherlands; +31 50 5877877; schutnl@schut.com

Take advantage of precise, repeatable inspection with a comprehensive set that combines hardened steel durability, fine 0.01 mm graduation and clear transport/storage in a tool trolley with a conformity certificate; order the set directly via Metav Werkzeuge or consult our specialists for application advice. Gauge Pin Set MS910.460 — hardened steel, 0.5–12 mm, Filetta The Gauge Pin Set MS910.460 is a complete inspection kit of precision gauge pins for workshop and production metrology, designed for routine go/no‑go checks, dimensional verification and assembly control Extensive set: 1151 gauge pins 0.5–12 mm Hardened steel for high wear resistance 0.01 mm graduation for precise selection Supplied in trolley with conformity certificate Reliable precision for repetitive inspection This set delivers high precision across a broad micro range, covering 0.5–12 mm with a graduation of 0.01 mm, which supports fine incremental selection during inspection procedures. The measured accuracy of 0.002 mm provides a verifiable basis for routine quality checks and contributes directly to stable production outcomes. Using hardened components reduces wear, so nominal sizes remain consistent over repeated use, limiting rework and saving time in the measurement chain. Designed to streamline workshop workflows Presented as a full kit in a purpose‑fitted tool trolley, the collection of pins is organised in individual plastic containers with size marking for rapid retrieval and immediate traceability. The integrated holders with good/reject indication simplify visual sorting and speed up go/no‑go decisions at the bench. These layout and handling choices reduce operator time per check and improve throughput without compromising measurement reliability. Robust handling with traceable conformity Constructed from hardened steel and supplied with a conformity certificate, the set emphasises longevity and documented quality assurance. Individual containers protect each gauge pin from contamination and damage, while the trolley format supports safe transport and tidy storage. The combination of durable materials and documented conformity helps maintain audit readiness and supports consistent measurement results across shifts. Versatile applications across metrology tasks Suitable for inspection, assembly verification and gauge‑based calibration work, the collection is tailored to routine tasks in production, toolmaking and inspection labs. The fine step size enables close fit control and small‑feature checks, while the extensive count of pins in the set covers a wide range of nominal sizes without the need for multiple purchases. The format is particularly useful where rapid switching between sizes and clear go/no‑go indication are required. For hands‑on advice or to secure the Filetta Gauge Pin Set MS910.460 for a stable inspection routine, contact Metav Werkzeuge — our consultants provide practical application support from Emmerich and ensure timely supply to the workshop. Technical data Article number: MS910.460 Name: Gauge pin set Manufacturer: Filetta Material: hardened steel Set: yes Accessories included: 3x holders with good/reject indicator Supplied: tool trolley with conformity certificate Packaging: pins in individual plastic containers with size marking Facts Measurement range: 0.5–12 mm Measurement increment: 0.01 mm Accuracy (nominal): 0.002 mm Pieces per set: 1151 Weight: 63 kg Dimensions (L×W×H): 670×350×540 mm Special features Hardened steel construction Individual marked containers for each pin Tool trolley delivery for transport and storage Conformity declaration included Holders with go/no‑go indicator included FAQ How fine are the increments in the set? The set provides a 0.01 mm graduation between sizes, enabling fine selection for close tolerance checks with the Gauge Pin Set MS910.460. Is the set suitable for repeated industrial use? Yes, the hardened steel pins and protective individual containers make the filetta gauge pin set appropriate for frequent workshop and production use. Does the delivery include documentation? Delivery includes a conformity certificate; the Gauge Pin Set MS910.460 is supplied with documentation confirming its compliance. Can the set be used for calibration tasks? The wide range and fine graduation allow the set to be used for inspection and informal calibration verification; for certified calibration procedures, refer to your internal quality protocols. What accessories come with the set? The set contains three holders with good/reject indication and all pins are housed in individual marked containers within the supplied trolley. Manufacturer / Responsible: Schut Geometrische Meettechniek bv; Duinkerkenstraat 21; 9723 BN Groningen; The Netherlands; +31 50 5877877; schutnl@schut.com

Take advantage of the combination of hardened steel construction, DIN 7162 compliance and an integrated wear allowance to ensure dependable go/no-go checks in serial inspection. Order the Filetta limit gauge pin directly via Metav Werkzeuge or request specialist advice for integration into existing inspection routines. Filetta Limit Gauge Pin — hardened steel, DIN 7162 Filetta Limit Gauge Pin designed for pass/fail checking of bores and inspection fixtures in industrial metrology Hardened steel construction to DIN 7162 Precision diameter 2.5 mm Wear allowance on the good side Compatible with go/no-go checking routines Reliable pass/fail checking for production control The limit gauge pin delivers a compact, unambiguous check for bore conformity using a simple go/no-go principle, minimising decision time on the shop floor. Manufactured to DIN 7162, the pin provides a clearly defined acceptance limit that supports reproducible inspections and consistent quality gates. The 2.5 mm diameter is specified to industry tolerances, enabling rapid visual and tactile confirmation without complex set‑ups. This direct verification method reduces downstream rework by catching out-of-tolerance parts at the earliest stage. Durability that reduces downtime and maintenance Constructed from hardened steel, the gauge pin resists wear in continuous use and preserves the inspection boundary over many cycles. The integrated wear allowance on the good side prolongs service life by permitting controlled dressing or replacement procedures while maintaining measurement integrity. Fewer replacements and predictable maintenance intervals lead to improved uptime in production lines and lower total cost of ownership. The robust material choice also supports use in regulated environments where repeatability matters. Simple integration into quality workflows and fixtures The pin is suited for fixtures, plug gauges and measuring rigs where straightforward verification is required. Its compact profile and standardised specification make stock management and fixture design straightforward, helping to keep inspection routines efficient. Clear identification (SKU MS911.161) and adherence to established norms aid traceability in quality records and simplify audits. The component is ideal for workshops and inspection stations seeking a pragmatic, standards-based tool to support routine quality control. Contact Metav Werkzeuge for tailored advice and to source the Filetta limit gauge pin (SKU MS911.161) directly from Emmerich — expert support for specification and delivery is available. Technical Data Article number: MS911.161 Manufacturer: Filetta Type: Limit gauge pin Diameter: 2.5 mm Standard: DIN 7162 Material: hardened steel Special note: wear allowance on the good side Facts Diameter: 2.5 mm Standard: DIN 7162 SKU: MS911.161 Special features Hardened steel construction Wear allowance of the good side Intended for go/no-go checking and plug gauge applications Category: gauges / measuring pins FAQ What material is the gauge pin made from? The Filetta limit gauge pin is manufactured from hardened steel, ensuring wear resistance and stable inspection boundaries (SKU MS911.161). Which standard applies to this gauge pin? Manufactured to DIN 7162, the component fulfils established requirements for limit gauges and supports clear pass/fail decisions. What does the wear allowance mean in practical terms? The wear allowance on the good side allows controlled use and maintenance so the gauge retains its acceptance limit for longer in serial inspections. Can this pin be used in fixture-based inspections? Yes, the pin is suitable for fixture and plug gauge applications where a defined go/no-go limit is required for bore checks. How is the size specified? The pin is specified with a diameter of 2.5 mm and supplied under SKU MS911.161 for unambiguous ordering and traceability. Manufacturer / Responsible: Schut Geometrische Meettechniek bv; Duinkerkenstraat 21; 9723 BN Groningen; The Netherlands; +31 50 5877877; schutnl@schut.com

Take advantage of a compact, standardised gauge that combines hardened steel construction with conformity to DIN 7162 for dependable go/no‑go verification; the built‑in wear allowance on the good side reduces rework and prolongs service intervals. Order the limit plug gauge directly via Metav Werkzeuge or ask our consultants if needed. Grenzlehrdorne — limit plug gauge in hardened steel, DIN 7162 (Filetta) The Grenzlehrdorne is a precision limit plug gauge designed for efficient go/no‑go checks and rapid acceptance testing across workshop and production environments. Hardened steel construction Conforms to DIN 7162 Wear allowance on good side Repeatable acceptance checks that speed up inspection A limit plug gauge of this design provides an immediate pass/fail decision, making go/no‑go verification both fast and unambiguous. Conformity with DIN 7162 guarantees that gauges are produced to a recognised industrial standard, which simplifies incoming inspection routines and reduces interpretation effort. By relying on a standardised gauge, throughput is improved and measurement uncertainty from subjective assessment is minimised, supporting a more efficient quality workflow. Durable construction that lowers lifecycle costs Manufactured from hardened steel, the gauge resists wear under repeated contact and maintains its dimensional stability over many cycles. The specified wear allowance on the good side compensates for gradual surface degradation, preserving functional fit and reducing the frequency of replacements. Fewer gauge changes mean less downtime and lower total cost of ownership for routine inspection tasks, especially in high‑volume production or repetitive quality checks. Practical fit for workshop and production use The compact limit plug gauge suits routine acceptance tasks and bench checks where quick decisions are required. Traceability is straightforward during audits when the article identifier MS911.162 is used in documentation, and the robust finish simplifies handling in busy environments. The gauge is particularly appropriate for verifying internal diameters where a simple, repeatable standard is preferable to time‑consuming measurement setups, thus keeping operations lean and reliable. Contact Metav Werkzeuge for tailored advice and supply of Filetta hardened‑steel limit plug gauges and to discuss the best gauge strategy for production or inspection needs Technical Data Article number: MS911.162 Material: hardened steel Standard: DIN 7162 Feature: wear allowance on good side Product type: limit plug gauge Numbers / Core technical data Nominal size: 3 mm Special features Hardened steel construction Design for go/no‑go verification Conformity to DIN 7162 Built‑in wear allowance on the good side FAQ What is the primary use of this limit plug gauge? The limit plug gauge from Filetta is intended for quick go/no‑go checks and acceptance testing of internal diameters where an unequivocal pass/fail result is required. Which standard does the gauge comply with? Compliance with DIN 7162 ensures the gauge meets established industrial production and inspection criteria. What material is used for the gauge and why does it matter? The gauge is made from hardened steel, which provides wear resistance and dimensional stability under repetitive use. How does the wear allowance affect service life? The wear allowance on the good side prolongs the functional life by compensating for gradual surface wear, maintaining fit for longer before requalification or replacement is required. How can the gauge be identified in documentation? Use the article number MS911.162 for traceability in inspection records and procurement lists. Manufacturer / Responsible: Schut Geometrische Meettechniek bv; Duinkerkenstraat 21; 9723 BN Groningen; The Netherlands; +31 50 5877877; schutnl@schut.com

Taking advantage of hardened steel construction and DIN 7162 conformity, this limit plug gauge delivers consistent pass/fail inspection for small bores; its Ø 6 mm nominal diameter and wear allowance on the good side support reproducible measurements and predictable service intervals. Order the limit plug gauge directly via Metav Werkzeuge or ask our consultants if needed. Filetta Limit Plug Gauge, Ø 6 mm, hardened steel (DIN 7162) A limit plug gauge for quick go/no‑go verification of internal diameters in production and inspection environments. Hardened steel construction for longevity Conforms to DIN 7162 standard Ø 6 mm nominal size for bore verification Includes wear allowance on the go side Reliable pass/fail inspection that saves time on the shop floor A compact verification tool designed for routine bore checks, the limit plug gauge offers immediate go/no‑go feedback without additional instrumentation. The hardened construction and standardised limits make it suitable for rapid in‑process checks and goods‑in inspections, reducing measurement cycles and minimising production delays. Using a simple tactile test, operators can maintain throughput while keeping quality gates intact — a practical solution where speed and repeatability matter. Robust materials and controlled wear for longer service life Manufactured from hardened steel, the gauge resists abrasion and stands up to repeated insertion into mating bores. The incorporated wear allowance on the go side provides a clear performance margin: wear can be monitored and replacement scheduled before limits are exceeded, preventing unexpected rejects. This feature translates into lower lifetime costs and predictable maintenance planning, particularly in high‑volume environments where tool longevity and consistent tolerance control are vital. Standards‑based accuracy for consistent production control Produced to DIN 7162, the gauge ensures compatibility with established inspection procedures and interchangeability across inspection stations. The defined geometry and limit definition simplify documentation in quality records and support conformity assessments during audits. As a single‑purpose limit gauge, it complements laboratory measuring equipment by offering a fast, unambiguous check that aligns with standardised inspection philosophies, improving overall process reliability. For DIN‑compliant limit plug gauges from Filetta, contact Metav Werkzeuge in Emmerich for expert advice and reliable supply of inspection tools Technical data Article number: MS911.168 Material: hardened steel Standard: DIN 7162 Nominal size: Ø 6 mm Facts Product type: limit plug gauge Application: pass/fail bore inspection Category: gauges / measuring pins Special features Wear allowance on the go side Simple tactile go/no‑go operation Suited for production and inspection environments FAQ What is the intended use of this limit plug gauge? This limit plug gauge is intended for quick go/no‑go verification of internal diameters in workshop and inspection settings; it provides immediate pass/fail assessment for bore checks. Which standard does the gauge comply with? The gauge is manufactured to DIN 7162, providing standardised limit geometry for consistent inspections. What material is used for the gauge and why does it matter? Made of hardened steel, the gauge offers wear resistance and a stable datum, which supports reproducible checks over many cycles. How does the wear allowance on the go side affect maintenance? The wear allowance gives a measurable margin for use: wear can be monitored and the gauge replaced before tolerances are lost, enabling planned maintenance and reducing downtime. Can this gauge be used for documented quality checks? Yes, the DIN‑compliant geometry and fixed limits make the gauge suitable for repeatable checks and inclusion in quality records. Manufacturer / Responsible: Schut Geometrische Meettechniek bv; Duinkerkenstraat 21; 9723 BN Groningen; The Netherlands; +31 50 5877877; schutnl@schut.com

Take advantage of a hardened steel construction and compliance with DIN 7162 to secure reliable go/no-go checks and predictable tool life; the integrated wear allowance on the datum face ensures continued conformity during repetitive use — order the gauge via Metav Werkzeuge or contact our consultants for application advice. Limit plug gauge G7, Ø 8 mm — hardened steel, DIN 7162 The Limit plug gauge G7 is a hardened-steel checking pin designed for fast dimensional inspections of holes and bores in production and inspection environments, conforming to DIN 7162 for consistent limit testing. Hardened steel construction Complies with DIN 7162 tolerance standard G7 limit fit for quick go/no-go testing Wear allowance on datum face Precise limit testing for production control The gauge provides a simple, repeatable method for pass/fail acceptance of bores, reducing measurement time on the shop floor. Built to the DIN 7162 guideline and marked for a G7 fit, the checking pin delivers clear go/no-go decisions that streamline quality routines. Relying on a fixed limit geometry removes interpretation variability and supports faster throughput in batch checks, while the compact design suits manual handling at inspection benches or assembly stations. Robust construction that withstands routine use Made from hardened steel, the mandrel offers resistance to wear and deformation under repeated contact. The incorporated wear allowance on the datum face compensates for gradual material loss, extending usable life and maintaining conformity between inspections. This durability translates into less downtime for replacements and a lower total cost of ownership compared with softer or plated designs, especially where regular mechanical gauging is part of the process. Traceable specification and simple integration into QC workflows Identified as MS911.170 and produced by Filetta, the gauge is straightforward to document within inspection plans and work instructions. The uncomplicated go/no-go principle requires no electrical hookup or data output, so the tool integrates seamlessly into manual or semi-automated checks. The combination of standardised tolerance adherence and a rugged profile supports clear process control and easier training of operators, which benefits both small workshops and larger production environments. Contact Metav Werkzeuge in Emmerich for application guidance and to source the Filetta limit plug gauge MS911.170 for your quality-control needs Technical Data Article number: MS911.170 Name: Limit plug gauge G7 Manufacturer: Filetta Standard: DIN 7162 Facts Nominal size: 8 mm Fit/tolerance: G7 Special features Material: hardened steel Wear allowance on datum face Application: go/no-go checking of holes and bores FAQ What type of inspection is this gauge intended for? The limit plug gauge is intended for quick go/no-go acceptance tests of bores and holes, enabling clear pass/fail checks during incoming inspection or in-process control with the Filetta MS911.170. Is the gauge suitable for continuous production use? Yes, the hardened steel construction and the wear allowance on the datum face make the gauge suitable for repetitive use in production environments where frequent verification of bore conformity is required. Does the gauge conform to a recognised standard? The limit plug gauge is manufactured to the requirements of DIN 7162, ensuring compatibility with common metrology practices and documentation in quality systems. How is the gauge identified within inspection documentation? The tool should be recorded as Filetta MS911.170, described as a G7 limit plug gauge, 8 mm, which simplifies traceability in inspection plans and process control records. Manufacturer / Responsible: Schut Geometrische Meettechniek bv; Duinkerkenstraat 21; 9723 BN Groningen; The Netherlands; +31 50 5877877; schutnl@schut.com

Taking advantage of a compact mm ↔ inch conversion reference and a workshop‑friendly format reduces calculation time and minimises measurement errors; this conversion table is an efficient aid for machining and metrology tasks. Order supply enquiries can be directed via Metav Werkzeuge for reliable fulfilment and specification advice. mm/inch conversion table by Filetta — Compact conversion reference The mm/inch conversion table is a compact reference sheet for rapid unit conversion between millimetres and inches, intended for use in machining, inspection and workshop settings. *Quick mm ↔ inch conversions at a glance *Compact, workshop‑friendly format *Durable print for regular use *Suitable for metrology and machining Faster conversions, fewer calculation errors A concise, printed conversion reference removes the need for repeated calculations and reduces transcription mistakes during setup and inspection. As a ready‑to‑hand reference, the table shortens cycle times in repetitive tasks and supports consistent results across operators. For processes where quick unit checks are required, the sheet complements digital instruments by providing an immediate, readable conversion between mm and inch, helping teams maintain workflow continuity without interrupting machine cycles. Integrates smoothly into metrology and workshop routines The mm/inch conversion table by Filetta fits naturally into quality control and production environments where mixed unit systems occur. The layout is designed for clear legibility during inspection rounds, enabling faster decision making in calibration, part verification and measurement documentation. In combination with calibrated measuring tools, this reference aids standardised entries in protocols and reduces interpretative errors when cross‑referencing drawings and fixtures, thereby supporting traceable measurement workflows. Compact format built for everyday use The slim, durable format makes the table easy to store at the bench, inside inspection folders or alongside tool trolleys; this promotes frequent use without degradation. Printed for clarity and longevity, the sheet is intended as a practical addition to training kits and workshop handbooks where quick access to mm ↔ inch conversions is required. The product is identified by SKU MS835.164, which simplifies catalogue reference and procurement within established supply chains. Request the Filetta mm/inch conversion table (SKU MS835.164) through Metav Werkzeuge for dependable supply from Emmerich and expert advice on specification and integration Technical data Article number: MS835.164 Product name: mm/inch conversion table Brand: Filetta Purpose: Conversion between mm and inch Facts Units: mm, inch Format: Reference table Physical dimensions: not specified Special features Compact, workshop‑friendly format Durable print suitable for regular use Intended for machining and inspection environments FAQ Is the table suitable for precision metrology use? The Filetta mm/inch conversion table is designed as a quick reference to support precision workflows but does not replace calibrated measuring instruments; it assists with unit interpretation and reduces conversion errors. Which units and ranges does the table cover? The sheet provides direct conversions between millimetres and inches for standard workshop ranges, enabling fast cross‑checks without calculation. Can the conversion table withstand everyday workshop conditions? The table is produced with a durable print and compact format intended for regular use at the bench or in inspection folders, making it suitable for routine workshop environments. Is the table useful for training and documentation? Yes, the reference format is well suited to training situations and documentation packs, helping new staff and trainees to interpret mixed‑unit drawings and measurement protocols. Filetta: Manufacturer / Responsible: Schut Geometrische Meettechniek bv; Duinkerkenstraat 21; 9723 BN Groningen; The Netherlands; +31 50 5877877; schutnl@schut.com