What is a limit gauge plug?

Benefit from a combination of hardened steel durability and conformity to DIN 7162, with a built‑in wear allowance on the go side that extends service life and maintains repeatable pass/fail decisions; order the limit gauge pin directly via Metav Werkzeuge or consult our specialists for application support. Limit gauge pin – hardened steel, DIN 7162 (Filetta) A limit gauge pin designed for rapid go/no‑go inspection in production and quality control, made to the DIN 7162 standard for consistent interchangeability and long‑term shop‑floor reliability Hardened steel construction Conforms to DIN 7162 Wear allowance on go side Faster pass/fail checks mean fewer production interruptions A compact, standards‑based gauge pin streamlines routine inspection by delivering clear go/no‑go decisions in one motion. The hardened construction reduces micro‑deformation under repeated contact, so checks stay reliable over thousands of cycles. For workshop managers this translates into shorter inspection times and fewer ambiguous measurements, supporting a predictable production flow and faster throughput. Durable design reduces inspection-related rework Built from hardened steel and specified to DIN tolerances, the pin resists wear that would otherwise necessitate early replacement. The incorporated wear allowance on the good (go) side compensates for gradual material loss, extending usable life and postponing recalibration or swap‑outs. Reduced tool turnover lowers maintenance interruptions and helps sustain inspection capacity on busy lines. Standards compliance supports traceability and interchangeability Conformance to DIN 7162 ensures that the pin mates with established limit gauge systems and that measured parts are judged against commonly accepted tolerances. The clear, repeatable geometry of the pin facilitates consistent judgement across operators and shifts, aiding quality documentation and supplier communication. Using standardised gauges simplifies audits and aligns measurement practice with industry expectations Speak to Metav Werkzeuge for application advice or to arrange supply of the Filetta limit gauge pin MS911.158 — call +49 2822 7131930 or e‑mail info@metav-werkzeuge.com for tailored recommendations Technical data Article number: MS911.158 Product name: Limit gauge pin Material: Hardened steel Standard: DIN 7162 Facts Mass / size designation: 1 SKU: MS911.158 Special features Wear allowance on go side Intended use: Go/no‑go inspection FAQ What is the primary application of this gauge pin? The Filetta limit gauge pin MS911.158 is intended for rapid go/no‑go checks in production and inspection environments, providing a clear pass or fail indicator for bore and pin checks. How does the wear allowance help in daily use? The wear allowance on the go side of the limit gauge pin compensates for gradual surface wear, prolonging the service life and maintaining reliable go/no‑go judgements over extended use. Is the pin compliant with recognised standards? Yes, the limit gauge pin MS911.158 is manufactured to DIN 7162, ensuring compatibility with standard limit gauge practices and facilitating exchangeability between tools. Manufacturer / Responsible: Schut Geometrische Meettechniek bv; Duinkerkenstraat 21; 9723 BN Groningen; The Netherlands; +31 50 5877877; schutnl@schut.com

Combining hardened steel construction, conformity to DIN 7162 and a deliberate wear allowance on the go side, this limit plug gauge delivers reproducible go/no‑go checks and extended service life in routine inspection tasks. Order the gauge directly via Metav Werkzeuge or contact our consultants for application guidance. Limit plug gauge — 1.5 mm, hardened steel (Filetta) A precision limit plug gauge intended for fast go/no‑go inspection of bore tolerances in workshop and production quality control. Hardened steel construction Conforms to DIN 7162 Wear allowance on the go side Precision Ø 1.5 mm Dependable go/no‑go inspection for production The Filetta limit plug gauge is built to provide consistent go/no‑go verification, enabling quick decisions on part conformity during serial production. Manufactured from hardened steel, the mandrel maintains contact geometry under repeated use, which supports reproducible results and reduces rework. Conformity with DIN 7162 ensures the gauge fits established tolerance schemes and can be integrated into existing inspection plans. Using a dedicated gauge pin for marker checks reduces measurement time compared with micrometre setups and simplifies operator training. Designed to resist wear and maintain accuracy A defining attribute is the wear allowance on the go side, which compensates for material loss during service and preserves the functional limit for a longer interval. This design choice delays the need for replacement while keeping the no‑go boundary stable, so inspection reliability is retained across production runs. The compact Ø 1.5 mm size is suitable for small bores and tight tolerances where a stiff, well‑finished pin is required. The result is lower total cost of ownership through extended service life and fewer unscheduled gauge changes. Quick integration into metrology workflows As a standardised gauge pin, this tool fits easily into bench inspection, go/no‑go fixtures and fixture verification routines. The simple geometry makes it suitable for use in pneumatic or manual checking stations and for rapid operator checks on the shop floor. Documentation and process planning benefit from the DIN 7162 reference, enabling clear pass/fail criteria in quality records. For workshops seeking a robust, compact checking instrument, the gauge pin accelerates inspection without sacrificing traceability or repeatability. Specify Filetta limit plug gauges through Metav Werkzeuge to standardise go/no‑go testing; contact our technical advisors at Metav Werkzeuge in Emmerich by email at info@metav-werkzeuge.com or by telephone at +49 2822 7131930 Technical Data SKU: MS911.159 Brand: Filetta Article: Limit plug gauge Facts Diameter: 1.5 mm Material: Hardened steel Standard: DIN 7162 Special features Wear allowance on the go side Category: Gauge pins / limit gauges Application: Go/no‑go inspection FAQ What is the primary use of this gauge? The limit plug gauge MS911.159 (Filetta limit plug gauge) is intended for rapid go/no‑go checks of bore tolerances in production and workshop quality control. What does the wear allowance on the go side mean? The wear allowance provides a designed margin on the go face so the functional acceptance limit remains reliable over prolonged use, extending the service life of the gauge pin. Which standard does the gauge comply with? This gauge conforms to DIN 7162, which defines the geometry and tolerance relationships for plug gauges used in bore inspection. What material is the gauge made from and why? The mandrel is manufactured from hardened steel to ensure durability, stiffness and stable contact geometry under repeated inspection cycles. Manufacturer / Responsible: Schut Geometrische Meettechniek bv; Duinkerkenstraat 21; 9723 BN Groningen; The Netherlands; +31 50 5877877; schutnl@schut.com

Taking advantage of a hardened-steel construction and conformity to DIN 7162, this limit plug gauge delivers reliable go/no-go inspection with an integrated wear allowance on the go side; order the Filetta gauge via Metav Werkzeuge or contact our consultants for supply and technical advice. Limit plug gauge MS911.222 by Filetta — hardened steel, DIN 7162 compliant The Limit plug gauge MS911.222 is a precision cylindrical gauge designed for rapid verification of internal diameters to DIN 7162, primarily intended for production control and incoming‑goods inspection Hardened steel construction to DIN 7162 18 mm nominal diameter gauge Wear allowance on the go side Precision gauge for internal diameter checks Consistent conformity through standardised construction The gauge is manufactured in hardened steel, offering dimensional stability and resistance to surface wear for repetitive checks. Built to DIN 7162, the design ensures compatibility with recognised inspection workflows and reduces ambiguity in acceptance criteria. Using a standardised limit plug means that measurement decisions are reproducible between operators and shifts, which helps to lower scrap rates and supports traceable quality routines across production lines. Practical benefit of the wear allowance and go/no‑go function A defined wear allowance on the go side prolongs useful life while maintaining effective pass criteria during routine use. The simple go/no‑go concept embedded in the geometry translates technical tolerance into an immediate decision—acceptable or not—so inspection cycles are faster and less error‑prone than subjective gauging. This functional clarity improves throughput in assembly and inspection stations and makes the gauge particularly suitable for high-volume checks where speed and reliability matter. Integration into inspection routines and fixtures Compact and robust, the instrument is straightforward to fit into gauge stands, inspection benches or assembly jigs for repetitive testing. The nominal diameter of 18 mm is clearly indicated for process documentation and facilitates inventorying of gauge sets. For workshop and production environments where quick verification and clear go/no‑go outcomes are required, this type of limit plug gauge supports consistent part acceptance and contributes to smoother downstream assembly operations. For a reliable supply of Filetta limit plug gauges and tailored advice for inspection setups, contact Metav Werkzeuge in Emmerich by e‑mail at info@metav-werkzeuge.com or by phone on +49 2822 7131930 — our consultants will assist with availability and order details Technical data Article number: MS911.222 Name: Limit plug gauge (Grenzlehrdorne) Manufacturer: Filetta Standard: DIN 7162 Measurements Nominal diameter: 18 mm Materials & features Material: hardened steel Feature: wear allowance on the go side FAQ What is the primary use of this gauge? The Filetta limit plug gauge MS911.222 is used for go/no‑go verification of internal cylindrical bores with a nominal diameter of 18 mm, enabling fast acceptance decisions in production inspection. Which standard does the instrument comply with? Manufactured to DIN 7162, the gauge follows established geometry and tolerance rules for limit plug gauges to ensure comparable inspection outcomes. How does the wear allowance affect service life? The wear allowance on the go side extends the gauge’s operational life by permitting controlled material loss before the no‑go limit is reached, maintaining reliable pass criteria for longer. Is the gauge suitable for fixture integration? Yes, the compact, hardened‑steel design of this limit plug gauge is suitable for mounting in gauge stands, inspection benches and jigs for repetitive testing. Manufacturer / Responsible: Schut Geometrische Meettechniek bv; Duinkerkenstraat 21; 9723 BN Groningen; The Netherlands; +31 50 5877877; schutnl@schut.com

Take advantage of precise, repeatable inspection in a compact format: robust hardened steel construction and compliance with DIN 7162 ensure reliable go/no‑go assessment and long service life; order the limit plug gauge directly via Metav Werkzeuge or request detailed specification support from our consultants. Limit plug gauge G7 (MS911.160) – hardened steel, DIN 7162 — Filetta Limit plug gauge G7 (MS911.160) for quick verification of bore tolerances in routine inspection and incoming goods control Hardened steel construction for longevity DIN 7162 compliant inspection gauge Wear allowance on the good side for service life Precision gauge pin, 2 mm nominal size Repeatable inspection that reduces rework and inspection time The limit plug gauge offers a straightforward method for verifying bore tolerances without complex measurement setups. Manufactured from hardened steel, the gauge provides consistent contact geometry and wear resistance; this translates into repeatable pass/fail checks at points of inspection, reducing the time spent on detailed measuring instruments and lowering the risk of unnecessary rework. Compliance with DIN 7162 ensures that acceptance criteria are clear and comparable across suppliers, supporting efficient quality control in production and incoming goods. Durable design with a built‑in allowance for wear A defining characteristic is the wear allowance on the good side, which compensates for gradual material loss during repeated use and maintains the defined acceptance margin for longer. The hardened substrate keeps the contact faces stable, so the gauge preserves its functional geometry under regular workshop conditions. For inspection routines where robustness and predictable service intervals matter, this design reduces downtime and the frequency of replacements, providing a reliable tool for standardised checks. Practical integration into workshop and inspection routines Designed as a simple go/no‑go instrument, the gauge is ideal for rapid checks on components during assembly, jig setting and final inspection. The compact format and clear acceptance principle make it suitable for bench use and for operators with basic training in metrology. Combined with a documented standard such as DIN 7162, the tool supports traceable inspection protocols and straightforward documentation in quality records, assisting both production staff and quality engineers in maintaining batch conformity. Discuss specification details with Metav Werkzeuge or request a technical comparison from our Emmerich hub — contact info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: MS911.160 Material: hardened steel Standard: DIN 7162 Nominal size: 2 mm Special feature: wear allowance on the good side Facts Product type: limit plug gauge Brand: Filetta SKU: MS911.160 Special features Robust contact faces Suitable for go/no‑go checks Purpose: bore tolerance verification Compact inspection tool for workshop use FAQ What is the primary use of this limit plug gauge? The limit plug gauge MS911.160 by Filetta is used for rapid go/no‑go verification of internal bore tolerances during incoming inspection and production control. What material is the gauge made from and why does that matter? The gauge is manufactured from hardened steel; this gives stable contact geometry and wear resistance, maintaining reliable inspection performance over repeated use. How does the wear allowance affect inspection intervals? The integrated wear allowance on the good side increases the effective service life by compensating for minor material loss, so maintenance and replacement intervals can be extended while preserving acceptance criteria. Manufacturer / Responsible: Schut Geometrische Meettechniek bv; Duinkerkenstraat 21; 9723 BN Groningen; The Netherlands; +31 50 5877877; schutnl@schut.com

Take advantage of the combination of hardened steel construction, DIN 7162 compliance and an integrated wear allowance to ensure dependable go/no-go checks in serial inspection. Order the Filetta limit gauge pin directly via Metav Werkzeuge or request specialist advice for integration into existing inspection routines. Filetta Limit Gauge Pin — hardened steel, DIN 7162 Filetta Limit Gauge Pin designed for pass/fail checking of bores and inspection fixtures in industrial metrology Hardened steel construction to DIN 7162 Precision diameter 2.5 mm Wear allowance on the good side Compatible with go/no-go checking routines Reliable pass/fail checking for production control The limit gauge pin delivers a compact, unambiguous check for bore conformity using a simple go/no-go principle, minimising decision time on the shop floor. Manufactured to DIN 7162, the pin provides a clearly defined acceptance limit that supports reproducible inspections and consistent quality gates. The 2.5 mm diameter is specified to industry tolerances, enabling rapid visual and tactile confirmation without complex set‑ups. This direct verification method reduces downstream rework by catching out-of-tolerance parts at the earliest stage. Durability that reduces downtime and maintenance Constructed from hardened steel, the gauge pin resists wear in continuous use and preserves the inspection boundary over many cycles. The integrated wear allowance on the good side prolongs service life by permitting controlled dressing or replacement procedures while maintaining measurement integrity. Fewer replacements and predictable maintenance intervals lead to improved uptime in production lines and lower total cost of ownership. The robust material choice also supports use in regulated environments where repeatability matters. Simple integration into quality workflows and fixtures The pin is suited for fixtures, plug gauges and measuring rigs where straightforward verification is required. Its compact profile and standardised specification make stock management and fixture design straightforward, helping to keep inspection routines efficient. Clear identification (SKU MS911.161) and adherence to established norms aid traceability in quality records and simplify audits. The component is ideal for workshops and inspection stations seeking a pragmatic, standards-based tool to support routine quality control. Contact Metav Werkzeuge for tailored advice and to source the Filetta limit gauge pin (SKU MS911.161) directly from Emmerich — expert support for specification and delivery is available. Technical Data Article number: MS911.161 Manufacturer: Filetta Type: Limit gauge pin Diameter: 2.5 mm Standard: DIN 7162 Material: hardened steel Special note: wear allowance on the good side Facts Diameter: 2.5 mm Standard: DIN 7162 SKU: MS911.161 Special features Hardened steel construction Wear allowance of the good side Intended for go/no-go checking and plug gauge applications Category: gauges / measuring pins FAQ What material is the gauge pin made from? The Filetta limit gauge pin is manufactured from hardened steel, ensuring wear resistance and stable inspection boundaries (SKU MS911.161). Which standard applies to this gauge pin? Manufactured to DIN 7162, the component fulfils established requirements for limit gauges and supports clear pass/fail decisions. What does the wear allowance mean in practical terms? The wear allowance on the good side allows controlled use and maintenance so the gauge retains its acceptance limit for longer in serial inspections. Can this pin be used in fixture-based inspections? Yes, the pin is suitable for fixture and plug gauge applications where a defined go/no-go limit is required for bore checks. How is the size specified? The pin is specified with a diameter of 2.5 mm and supplied under SKU MS911.161 for unambiguous ordering and traceability. Manufacturer / Responsible: Schut Geometrische Meettechniek bv; Duinkerkenstraat 21; 9723 BN Groningen; The Netherlands; +31 50 5877877; schutnl@schut.com

Take advantage of a compact, standardised gauge that combines hardened steel construction with conformity to DIN 7162 for dependable go/no‑go verification; the built‑in wear allowance on the good side reduces rework and prolongs service intervals. Order the limit plug gauge directly via Metav Werkzeuge or ask our consultants if needed. Grenzlehrdorne — limit plug gauge in hardened steel, DIN 7162 (Filetta) The Grenzlehrdorne is a precision limit plug gauge designed for efficient go/no‑go checks and rapid acceptance testing across workshop and production environments. Hardened steel construction Conforms to DIN 7162 Wear allowance on good side Repeatable acceptance checks that speed up inspection A limit plug gauge of this design provides an immediate pass/fail decision, making go/no‑go verification both fast and unambiguous. Conformity with DIN 7162 guarantees that gauges are produced to a recognised industrial standard, which simplifies incoming inspection routines and reduces interpretation effort. By relying on a standardised gauge, throughput is improved and measurement uncertainty from subjective assessment is minimised, supporting a more efficient quality workflow. Durable construction that lowers lifecycle costs Manufactured from hardened steel, the gauge resists wear under repeated contact and maintains its dimensional stability over many cycles. The specified wear allowance on the good side compensates for gradual surface degradation, preserving functional fit and reducing the frequency of replacements. Fewer gauge changes mean less downtime and lower total cost of ownership for routine inspection tasks, especially in high‑volume production or repetitive quality checks. Practical fit for workshop and production use The compact limit plug gauge suits routine acceptance tasks and bench checks where quick decisions are required. Traceability is straightforward during audits when the article identifier MS911.162 is used in documentation, and the robust finish simplifies handling in busy environments. The gauge is particularly appropriate for verifying internal diameters where a simple, repeatable standard is preferable to time‑consuming measurement setups, thus keeping operations lean and reliable. Contact Metav Werkzeuge for tailored advice and supply of Filetta hardened‑steel limit plug gauges and to discuss the best gauge strategy for production or inspection needs Technical Data Article number: MS911.162 Material: hardened steel Standard: DIN 7162 Feature: wear allowance on good side Product type: limit plug gauge Numbers / Core technical data Nominal size: 3 mm Special features Hardened steel construction Design for go/no‑go verification Conformity to DIN 7162 Built‑in wear allowance on the good side FAQ What is the primary use of this limit plug gauge? The limit plug gauge from Filetta is intended for quick go/no‑go checks and acceptance testing of internal diameters where an unequivocal pass/fail result is required. Which standard does the gauge comply with? Compliance with DIN 7162 ensures the gauge meets established industrial production and inspection criteria. What material is used for the gauge and why does it matter? The gauge is made from hardened steel, which provides wear resistance and dimensional stability under repetitive use. How does the wear allowance affect service life? The wear allowance on the good side prolongs the functional life by compensating for gradual surface wear, maintaining fit for longer before requalification or replacement is required. How can the gauge be identified in documentation? Use the article number MS911.162 for traceability in inspection records and procurement lists. Manufacturer / Responsible: Schut Geometrische Meettechniek bv; Duinkerkenstraat 21; 9723 BN Groningen; The Netherlands; +31 50 5877877; schutnl@schut.com

The combination of robust hardened steel, conformity to DIN 7162 and a precise 4.5 mm nominal size ensures reliable pass/fail checks and long service life for small-bore inspection tasks; order the limit plug gauge directly via Metav Werkzeuge or consult our technical advisors for application-specific guidance. Limit plug gauge G7 – 4.5 mm, hardened steel by Filetta The Limit plug gauge G7 is a compact inspection pin designed for rapid go/no‑go acceptance testing of holes and bores in production and quality control settings. Hardened steel construction Conforms to DIN 7162 tolerance 4.5 mm nominal diameter Wear allowance on the go side Precision checks that speed up inspection A dedicated plug gauge built to DIN 7162 provides a straightforward, traceable method for go/no‑go assessment. The gauge’s 4.5 mm nominal size and G7 designation make it suitable for small-diameter bores where repeatable acceptance criteria are required. As a limit gauge, it converts geometric requirements into a tactile pass/fail verdict, reducing interpretation time during routine checks. The hardened construction maintains the calibrated profile over repeated use, supporting consistent process decisions and fewer downstream reworks. Robust design that reduces maintenance intervals Manufactured from hardened steel, the gauge resists premature wear in standard workshop environments, while the integrated wear allowance on the go side provides an engineered margin to extend useful life without compromising measurement integrity. This design choice lowers the frequency of replacements and conserves inspection resources, which translates into reduced process interruptions and predictable tooling budgets. The simple, single‑feature function of the instrument makes it a durable choice for shop‑floor verification and repetitive production control. Practical procurement and workshop integration The compact format and clear specification—listed under SKU MS911.165—enable easy stock management and fast identification in procurement systems. As a standardised acceptance tool, the plug gauge fits into established quality routines and can be used alongside other control artefacts to document conformity. Choosing a gauge from a recognised supplier supports traceability and aligns with systematic inspection plans; Metav’s distribution and inventory handling further simplify replenishment and selection for industrial and trade customers. Contact Metav Werkzeuge in Emmerich for availability and application advice on the Filetta limit plug gauge MS911.165 and to arrange delivery or technical consultation Technical data Article number: MS911.165 Material: hardened steel Nominal diameter: 4.5 mm Standard: DIN 7162 Facts Product type: limit plug gauge Designation: G7 Category: Gauges; Pin gauges Special features Wear allowance on the go side Compact inspection pin for small bores Suitable for routine go/no‑go acceptance testing FAQ What is the intended use of this limit plug gauge? The Filetta limit plug gauge MS911.165 is intended for quick go/no‑go checks of small bores to verify dimensional conformity to a specified tolerance class. How does the wear allowance affect service life? The built‑in wear allowance on the go side delays rejection due to normal surface wear, extending the practical lifetime of the gauge while maintaining reliable pass/fail decisions. Is the gauge suitable for use on finished components in production? Yes, the hardened‑steel construction and conformity to DIN 7162 make this limit plug gauge suitable for routine inspection of finished parts on the production line. Can this gauge be used for calibration or measurement recording? As a go/no‑go limit gauge, it serves as a conformity check rather than a measuring instrument for recorded dimensions; traceable gauge records should be maintained per internal quality procedures. Manufacturer / Responsible: Schut Geometrische Meettechniek bv; Duinkerkenstraat 21; 9723 BN Groningen; The Netherlands; +31 50 5877877; schutnl@schut.com

Take advantage of a compact, standards‑compliant checking solution: a hardened‑steel limit plug gauge that meets DIN 7162 and includes a wear allowance on the go side for extended service life; order via Metav Werkzeuge or consult their specialists for application advice. Limit plug gauges MS911.213 — hardened steel, DIN 7162 A limit plug gauge MS911.213 for fast go/no‑go checking and acceptance testing of 9 mm bores in production and inspection environments Hardened steel construction DIN 7162 compliant Wear allowance on go side Fast, reliable acceptance checks on the shop floor For routine inspection and first‑piece approval, a compact go/no‑go gauge provides immediate, objective results. The hardened body resists abrasion so tolerance boundaries remain stable over repeated cycles, while the simple two‑position concept reduces operator decisions to a single pass/fail action. This lowers cycle time in quality control and removes ambiguity from visual measurements, making process control faster and more consistent. Durability that reduces downtime and recalibration cycles The hardened steel used in this design is selected to maintain dimensions under mechanical stress and frequent handling. The integrated wear allowance on the go side extends the usable life before refurbishment is required, which reduces the frequency of replacements and preserves measurement reliability between maintenance intervals. For high‑turnover inspection points, this translates into fewer interruptions and lower total cost of ownership. Standards-based traceability for audit and production control Manufactured to DIN 7162, the gauge aligns with widely accepted metrology practice for limit gauges, simplifying documentation and acceptance during audits. Conformity to the standard means the tool can be relied upon for contractual checks and in‑line sampling plans where repeatable limits are essential. The compact format and clear definition of the checking faces support consistent results across shifts and operators. Practical advantages in inspection and fixture testing The small diameter of 9 mm makes the device particularly suitable for plug checks in small‑bore components, jigs and fixtures used in precision assembly. As a purpose‑designed gauge pin, it fits into production routines without the need for elaborate setup, and its robust construction withstands the handling typical in workshop and toolroom environments. Use in go/no‑go sequences or as a quick reference tool helps shorten inspection throughput while keeping decision criteria unambiguous. For production‑grade bore control, request the Filetta limit plug gauge MS911.213 through Metav Werkzeuge — their advisors will confirm suitability for the intended application and arrange supply details Technical Data Article number: MS911.213 Product: Limit plug gauges Brand: Filetta Material: hardened steel Standard: DIN 7162 Size / diameter: 9 mm Special note: wear allowance on go side Facts SKU: MS911.213 Category: gauges / gauge pins Image available: yes Special features Designed for go/no‑go checking Intended for production and inspection use Wear‑compensated go side Robust hardened construction FAQ What is the primary purpose of this gauge? The limit plug gauge MS911.213 is intended for go/no‑go checking and quick acceptance testing of 9 mm bores in production and inspection processes. Which material is used for the gauge? This gauge is made from hardened steel to provide abrasion resistance and long service life under repetitive use. Is the gauge standardised? Yes, the tool is manufactured in accordance with DIN 7162, ensuring consistent limits and traceable use in quality systems. How does the wear allowance affect usage? The wear allowance on the go side prolongs the period during which the gauge reliably represents the intended limit, reducing replacement frequency and maintaining inspection integrity. Can this gauge be used in fixture and jig checks? The compact 9 mm diameter and robust design make it suitable for plug checks in fixtures, jigs and small‑bore components during assembly and testing. Manufacturer / Responsible: Schut Geometrische Meettechniek bv; Duinkerkenstraat 21; 9723 BN Groningen; The Netherlands; +31 50 5877877; schutnl@schut.com