What is a thread limit plug gauge?

Take advantage of accurate diameter checks, a compact 0.5–10 mm range and robust steel construction to streamline drill verification in the workshop. Order the item directly via Metav Werkzeuge or consult our specialists for tailored advice. Drill Gauge MS910.501 — steel drill gauge, 0.5–10 mm range The Drill Gauge MS910.501 is a compact steel gauge designed for rapid identification and verification of drill diameters in workshop, tooling and inspection environments. Robust steel construction Measuring range 0.5–10 mm Steps every 0.1 mm for quick checks Compact size ideal for micro measurements Fast, reliable diameter checks that speed up inspection The instrument enables immediate validation of drill sizes, offering a measuring range of 0.5–10 mm with clear, regular increments of 0.1 mm for fast go/no-go decisions. This makes the tool particularly effective when time is critical: operators spend less time searching for the right drill and more time on machining. The compact form factor supports quick handling at the bench or next to a machine, reducing workflow interruptions and improving throughput. Built for repeatable precision and easy interpretation Constructed from steel for consistent dimensional stability and wear resistance, the gauge provides repeatable checks across many cycles of use. The regular step spacing simplifies visual comparison between the tool and the corresponding gauge slot, which is especially useful when a production line requires fast sampling rather than laboratory-level metrology. The simple mechanical design avoids electronics, so operation remains straightforward and maintenance demands are minimal while preserving dependable performance. Suited to micro work and small-scale quality control With its maximum measuring range of 10 mm, the gauge is classified in the micro category—ideal for fine mechanical and watchmaking tasks as well as routine checks in general machining where small-diameter drills are common. The tool supports quick decision-making during setup and run-time inspections, contributing to consistent part quality and fewer tool-change mistakes. Where traceable calibration is required, consultancy on calibration options can be provided to match workshop quality routines. Contact Metav Werkzeuge for procurement details, calibration options and application advice on the Filetta Drill Gauge MS910.501 — direct supply from Emmerich to the workshop bench. Technical data Article number: MS910.501 Manufacturer: Filetta Type: Drill gauge Facts Measuring range: 0.5–10 mm Step size: 0.1 mm Minimum: 0.5 mm Maximum: 10 mm Special features Material: Steel Application: Drill diameter verification Category: Gauges / Measuring pins FAQ What measuring range does this gauge cover? The gauge covers a range from 0.5 mm to 10 mm, making the Drill Gauge MS910.501 suitable for small-diameter drill checks. How fine are the increments on the gauge? Increments are 0.1 mm, which allows for quick visual checks and straightforward go/no-go comparison when verifying drill diameters. Is the gauge suitable for workshop use or only for metrology labs? Designed for practical workshop use, the Filetta drill gauge provides robust, repeatable checks ideal for bench and production environments. What material is the gauge made from? The gauge is made from steel, selected for dimensional stability and wear resistance under regular inspection cycles. Can the gauge be used during machine setup? Yes, the compact size and clear steps make the MS910.501 convenient for use during machine setup and routine sampling inspections. Manufacturer / Responsible: Schut Geometrische Meettechniek bv; Duinkerkenstraat 21; 9723 BN Groningen; The Netherlands; +31 50 5877877; schutnl@schut.com

Take advantage of robust hardened steel construction and DIN 7162 conformity to secure reproducible bore checks; the built‑in wear allowance on the good side extends service life and simplifies limit interpretation. Order the Filetta items via Metav Werkzeuge or contact our consultants for application advice. Limit plug gauge by Filetta — hardened steel, DIN 7162, Ø 12 mm, G7 Limit plug gauge designed for rapid acceptance checks of internal diameters in production and incoming‑goods inspection Hardened steel for durable measurement Conforms to DIN 7162 standard Wear allowance on the 'go' side Reliable diameter assessment that speeds inspection throughput The limit plug gauge serves as a straightforward go/no‑go check for cylindrical bores, offering rapid verification without complex setup. Machined to a nominal diameter of 12 mm with the designation G7, the pin provides an immediate pass/fail indication that reduces inspection time compared with full dimensional measuring chains. The hardened construction minimises deformation under repeated use, which keeps the checking routine stable and helps maintain production rhythm. For shop floors and control benches where speed and repeatability matter, the gauge translates metrological specification into a clear decision at the point of measurement. Durable design that reduces replacement and downtime Made from hardened steel, the gauge withstands frequent handling and contact with metal workpieces. A specific wear allowance on the good side compensates for gradual material loss, so the go end retains acceptance criteria longer and service intervals are extended. This pragmatic feature lowers life‑cycle costs by delaying the need for reworking or replacement and by keeping inspection standards consistent. The combination of robust material and wear management supports continuous operation in industrial environments where tools are subject to intensive use. Simple integration into quality processes and documentation Conforming to DIN 7162 assists traceability in formal inspection plans and quality records. The plug gauge is suitable for routine acceptance checks in production, final inspection and incoming goods control where clear binary results are preferred. The concise form factor and unambiguous results streamline operator training and reduce human decision variance, which improves overall process capability. When used as part of a calibrated inspection set, the gauge helps to demonstrate compliance and to maintain documented control over critical bore dimensions. Practical benefits for workshop and production use This gauge simplifies everyday metrology: no complex calibration rigs are required for routine use, and the hard wearing surface minimises surface damage to both gauge and workpiece. The compact geometry facilitates access to bores in assemblies and jigged components, while the standardised dimensioning and tolerance marking enable easy cross‑referencing with drawing specifications. For manufacturing teams seeking dependable, low‑effort tools for Go/No‑Go inspection, the pin combines industrial robustness with clear operational benefits. Choose the Filetta limit plug gauge with G7 tolerance via Metav Werkzeuge for dependable in‑process checks; contact Metav Werkzeuge in Emmerich for tailored advice at info@metav-werkzeuge.com or +49 2822 7131930 Technical Data Article number: MS911.174 Product: Limit plug gauge Brand: Filetta Facts Nominal diameter: 12 mm Standard: DIN 7162 Designation: G7 Special features Material: hardened steel Wear allowance on the go side Intended for go/no‑go bore inspection FAQ What size bore is this gauge intended to check? The gauge is supplied as a 12 mm nominal limit plug gauge and is intended for quick go/no‑go checks of bores matching that nominal diameter. Is the gauge suitable for production use on a shop floor? Yes, the hardened‑steel construction and the wear allowance on the good side make the gauge robust enough for routine production and incoming‑goods inspection. How does the G7 designation influence measurement results? G7 is the designation provided with the article and identifies the tolerance fit intended for interpretation against corresponding drawing tolerances when using the plug gauge. Does the gauge comply with industry standards? The item is produced to conform with DIN 7162, facilitating inclusion in standard inspection procedures and documentation. Manufacturer / Responsible: Schut Geometrische Meettechniek bv; Duinkerkenstraat 21; 9723 BN Groningen; The Netherlands; +31 50 5877877; schutnl@schut.com

Benefit from the combination of hardened steel construction and conformity to DIN 7162 for repeatable internal diameter checks; the 15 mm nominal size offers a direct fit for standard bores. Order the limit plug gauge directly via Metav Werkzeuge or consult our specialists for application advice. Limit plug gauge – 15 mm, hardened steel (Filetta) Limit plug gauge for quick go/no-go verification of internal diameters in production and inspection Hardened steel construction Compliant with DIN 7162 standard 15 mm nominal diameter gauge Wear allowance on master side Precision inspection where it matters The limit plug gauge is designed for fast and reliable verification of internal bores in routine quality checks. Manufactured from hardened steel, the gauge offers mechanical resilience that reduces wear and maintains form under repeated use. Conformity with DIN 7162 ensures that the gauge fits established acceptance procedures and inspection protocols, simplifying integration into existing quality workflows. As a result, production lines gain a compact, low-effort control tool that supports consistent pass/fail decisions. Durability and traceable performance A clear technical advantage of this gauge is the incorporated wear allowance on the master side, which prolongs usable life and offers predictable wear behaviour. The material choice—hardened steel—provides resistance to deformation and abrasion, reducing dimensional drift during frequent checks. For workshops and inspection rooms that require robust tools rather than disposable checking aids, this construction translates into fewer replacements and stable measurement outcomes over time, supporting reliable component acceptance. Simple handling for reliable results The gauge’s nominal 15 mm size and compact form factor make it suitable for rapid in-process checks and bench inspection tasks in metalworking and assembly. As a limit gauge, it provides unambiguous go/no-go feedback without needing additional measurement devices, speeding up throughput while keeping control simple. The Filetta item (Article number MS911.177) is particularly suited to operators who prioritise straightforward inspection methods and durable tooling that aligns with recognised standards. For reliable acceptance testing and long-term workshop use, request the Filetta limit plug gauge from Metav Werkzeuge—technical advice and supply are available via info@metav-werkzeuge.com or by phone on +49 2822 7131930 Technical data Article number: MS911.177 Name: Limit plug gauge Brand: Filetta Facts Diameter: 15 mm Standard: DIN 7162 Special features Material: hardened steel Application: internal diameter verification (plug gauge) Special feature: wear allowance on master side Category: Gauges (Measuring instruments > Gauges) FAQ What is the intended use of this limit plug gauge? The limit plug gauge is intended for go/no-go checks of internal diameters in production and inspection; the Filetta gauge MS911.177 verifies whether bores meet the specified acceptance limits. Is the gauge suitable for continuous shop-floor use? Yes, the hardened steel construction of the Filetta limit plug gauge ensures robustness for frequent shop-floor inspections and routine quality control. Which standard does the gauge conform to? The gauge conforms to DIN 7162, meaning it fits standard inspection routines and documented acceptance criteria for plug gauges. Manufacturer / Responsible: Schut Geometrische Meettechniek bv; Duinkerkenstraat 21; 9723 BN Groningen; The Netherlands; +31 50 5877877; schutnl@schut.com

Combining hardened steel construction, conformity to DIN 7162 and a deliberate wear allowance on the good side delivers dependable limit checking and extended service life in routine inspection tasks; order Filetta limit gauge pins via Metav Werkzeuge or consult our specialists for selection and supply advice. Limit gauge pin by Filetta — hardened steel, DIN 7162 Limit gauge pin designed for Go/No‑Go checks in production and QA environments Limit gauge pin ø 17 mm, hardened steel Conforms to DIN 7162 tolerances Wear allowance on the good side Suitable for plug and pin gauge control Dependable limit checking that stabilises production quality The solid, dimensionally stable construction supports fast, repeatable inspections on the shop floor and in quality control. Built from hardened steel, this pin maintains its nominal size under cyclic use, which reduces the risk of false rejects and rework. Conformity to DIN 7162 provides an objective reference for acceptance testing and helps to harmonise checks across suppliers and production lines, improving throughput and lowering non‑conforming parts per million. Reduced downtime thanks to a wear‑compensated design The integrated wear allowance on the good side extends the usable life of each pin by allowing controlled material loss while preserving the accept signal for Go checks. For maintenance planners and inspectors this means fewer replacements and more predictable tool cycles. The design philosophy emphasises long‑term precision, so inspection intervals can be scheduled on condition rather than by conservative fixed replacement, saving operational time without compromising measurement integrity. Practical suitability for workshop and gauge sets Manufactured for routine limit inspection duties, the pin is compact and straightforward to integrate into existing gauge sets and fixtures. The simple geometry supports quick insertion for plug checks and is compatible with standard bench routines. For technical procurement and production engineering teams, the combination of material choice and standard compliance provides a reliable basis for procurement decisions and spares planning, while Metav Werkzeuge can advise on kit assembly and batch supply options. For specification support or stock availability of Filetta limit gauge pins (MS911.179) contact Metav Werkzeuge for a tailored recommendation at info@metav-werkzeuge.com or call +49 2822 7131930 Technical Data Article number: MS911.179 Manufacturer: Filetta Size / Diameter: 17 mm Material: hardened steel Standard: DIN 7162 Special feature: wear allowance on the good side Specifications Diameter: 17 mm Design & Features Category: limit gauge pin / plug gauge Intended use: Go/No‑Go limit checking and quality control Application area: production inspection, incoming goods control FAQ What is this pin used for in production? This limit gauge pin (Filetta, MS911.179) is used for Go/No‑Go checks and routine limit inspections to verify bore and fit dimensions on parts. Does the pin meet a recognised standard? Yes, the Filetta pin complies with DIN 7162, ensuring standardized tolerance classes for limit gauges. How does the wear allowance affect service life? The built‑in wear allowance on the good side prolongs usable life by permitting controlled wear while maintaining the Go limit, reducing replacement frequency. Can Metav Werkzeuge supply matching gauge sets or replacements? Metav Werkzeuge can advise on compatible gauge sets and supply quantities; the Filetta MS911.179 can be ordered as part of a coordinated inspection kit. Manufacturer / Responsible: Schut Geometrische Meettechniek bv; Duinkerkenstraat 21; 9723 BN Groningen; The Netherlands; +31 50 5877877; schutnl@schut.com

Take advantage of the combination of hardened steel construction, DIN 7162 compliance and an integrated wear allowance for consistent pass/fail decisions and extended service life. Order the limit plug gauge directly via Metav Werkzeuge or contact our consultants for specification advice. Limit plug gauge – Filetta, hardened steel, DIN 7162 The Limit plug gauge is a precision go/no-go inspection pin designed for fast dimensional checks of bores and fittings in production and quality control. Hardened steel construction Manufactured to DIN 7162 Wear allowance on the good side Reliable pass/fail checking for fast quality control A compact limit plug gauge provides a straightforward binary decision in inspection routines, turning measurement into an immediate pass or fail. The combination of DIN 7162 conformity and a hardened shaft ensures that the gauge meets recognised geometric and tolerance requirements, which reduces interpretation time in quality control and accelerates throughput on the shop floor. This approach lowers downtime created by uncertain measurements and supports reproducible, traceable inspection results. Built for longevity and repeatable results Constructed from hardened steel, the pin resists abrasion and maintains a stable measuring diameter over many cycles, so calibration intervals can be extended without compromising confidence. The included wear allowance on the good side compensates for normal surface degradation, preserving the functional limit for go checks and reducing the need for immediate replacement. For maintenance planning this translates into predictable lifecycle costs and less frequent tool changeovers. Easy integration into workshop inspection processes Compliance with DIN 7162 means the gauge integrates cleanly into existing inspection plans and can be referenced in control documentation and reports. The simple geometry and compact design facilitate handheld use or fixture mounting, enabling quick comparison checks during in-process inspection or final quality control. The instrument functions as an efficient screening tool before more detailed metrology is applied, saving time while keeping measurement risk low. Suited applications and practical advantages Ideal for routine bore verification and acceptance testing, the gauge is suited to mechanical engineering, component assembly and finishing operations where fast, reproducible decisions are required. The small footprint of the pin makes it convenient in tight work stations and on assembly lines, while the robust material and standardised manufacture support long-term reliability. Where quick verification is needed, the plug gauge acts as a dependable first check. For DIN‑compliant limit gauging and practical advice from our Emmerich quality filter, contact Metav Werkzeuge to order Filetta limit plug gauges or to discuss application-specific recommendations: info@metav-werkzeuge.com / +49 2822 7131930. Technical data Article number: MS911.206 Manufacturer: Filetta Material: hardened steel Standard: DIN 7162 Measurements Size: 4 mm Special features Wear allowance on the good side Category: Gauge pins / plug gauge Application: Pass/fail inspection of bores FAQ What is the primary purpose of this limit plug gauge? The limit plug gauge is intended for quick pass/fail verification of bore diameters and mating features during production and final inspection. Which material is used for the gauge? The Filetta limit plug gauge is made from hardened steel to ensure wear resistance and dimensional stability. Does the gauge comply with any standards? Yes, the gauge is manufactured in accordance with DIN 7162, ensuring standardised geometry and tolerance handling. What size does this article cover? This item is specified with a size of 4 mm and is listed under article number MS911.206. How does the wear allowance affect inspection? The built-in wear allowance on the good side maintains the effective go condition as the surface experiences normal abrasion, thus extending service life while preserving reliable go/no-go decisions. Manufacturer / Responsible: Schut Geometrische Meettechniek bv; Duinkerkenstraat 21; 9723 BN Groningen; The Netherlands; +31 50 5877877; schutnl@schut.com

The combination of hardened steel construction, DIN 7162 conformity and a built‑in wear allowance on the good side provides reliable, repeatable limit checks with low life‑cycle cost; order this limit plug gauge directly via Metav Werkzeuge or consult our specialists for application advice. Limit plug gauge G7 — 7 mm, hardened steel (Filetta) The limit plug gauge G7 is a precision limit gauge designed for rapid go/no‑go verification of bore diameters in production and inspection environments. Hardened steel for lasting dimensional stability Conforms to DIN 7162 for standardised tolerances Wear allowance on the 'good' side for reconditioning Ideal for rapid go/no‑go bore checks Fast, standards‑based inspection to keep throughput steady This limit gauge is manufactured from hardened steel and produced to DIN 7162, ensuring that each check delivers a clear, standards‑based decision: accept or reject. The compact pin form factor enables go/no‑go testing at production stations or in the quality lab with minimal setup time. By using a dedicated limit pin for a specific nominal diameter, process control becomes faster and less error‑prone than repeated measurement and calculation, improving overall line efficiency. Built for durability and easy maintenance The design incorporates an explicit wear allowance on the good side, which preserves functional limits after regrinding and extends service life. This intentional allowance means the pin can be reconditioned rather than replaced when surface wear appears, reducing total cost of ownership and downtime. The hardened surface resists abrasion in routine checks, while the clear distinction of the 'good' and 'no‑go' ends simplifies handling and reduces the risk of incorrect use. Practical fit for shop‑floor quality routines As a limit checking tool, the plug gauge integrates into visual and tactile inspection routines: a clear pass or fail removes ambiguity and accelerates decision loops. The small nominal diameter of 7 mm suits components in mechanical assemblies, hydraulic and pneumatic parts, and small‑bore workpieces where quick verification is required. Lightweight and compact, the gauge is easy to store at point of use and to include in inspection kits, helping standardise checks across operators and shifts. For procurement or technical clarification about Filetta limit plug gauges and availability via Metav Werkzeuge, contact our Emmerich team for tailored advice and stock information Technical data Article number: MS911.169 Brand: Filetta Nominal size: 7 mm Material: hardened steel Standard: DIN 7162 Facts Product type: limit plug gauge (go/no‑go) SKU: MS911.169 Typical application: bore diameter verification Format: pin / plug gauge Special features Wear allowance on the good side for regrinding Conforms to standardised tolerances (DIN 7162) Robust surface hardness for repeated checks FAQ What tolerance standard does this limit gauge follow? The limit plug gauge is manufactured to DIN 7162, which defines the dimensional and tolerance requirements used for standardised go/no‑go gauges. Can the gauge be reconditioned when worn? Yes, the built‑in wear allowance on the good side permits regrinding and requalification so the gauge remains serviceable over a longer period. Is this gauge suitable for quick shop‑floor checks of small bores? Yes, the 7 mm nominal diameter and pin format make the gauge well suited to rapid verification of small bores in production and inspection stations. Which materials is the gauge intended to inspect? The gauge is intended for dimensional verification of bores regardless of the workpiece material; material compatibility depends on the component, not the gauge itself. How is the pass/fail decision presented during inspection? The plug gauge provides an immediate pass/fail result: the go end should enter the bore, while the no‑go end must not, enabling unambiguous acceptance control. Manufacturer / Responsible: Schut Geometrische Meettechniek bv; Duinkerkenstraat 21; 9723 BN Groningen; The Netherlands; +31 50 5877877; schutnl@schut.com

Take advantage of a hardened steel construction and compliance with DIN 7162 to secure reliable go/no-go checks and predictable tool life; the integrated wear allowance on the datum face ensures continued conformity during repetitive use — order the gauge via Metav Werkzeuge or contact our consultants for application advice. Limit plug gauge G7, Ø 8 mm — hardened steel, DIN 7162 The Limit plug gauge G7 is a hardened-steel checking pin designed for fast dimensional inspections of holes and bores in production and inspection environments, conforming to DIN 7162 for consistent limit testing. Hardened steel construction Complies with DIN 7162 tolerance standard G7 limit fit for quick go/no-go testing Wear allowance on datum face Precise limit testing for production control The gauge provides a simple, repeatable method for pass/fail acceptance of bores, reducing measurement time on the shop floor. Built to the DIN 7162 guideline and marked for a G7 fit, the checking pin delivers clear go/no-go decisions that streamline quality routines. Relying on a fixed limit geometry removes interpretation variability and supports faster throughput in batch checks, while the compact design suits manual handling at inspection benches or assembly stations. Robust construction that withstands routine use Made from hardened steel, the mandrel offers resistance to wear and deformation under repeated contact. The incorporated wear allowance on the datum face compensates for gradual material loss, extending usable life and maintaining conformity between inspections. This durability translates into less downtime for replacements and a lower total cost of ownership compared with softer or plated designs, especially where regular mechanical gauging is part of the process. Traceable specification and simple integration into QC workflows Identified as MS911.170 and produced by Filetta, the gauge is straightforward to document within inspection plans and work instructions. The uncomplicated go/no-go principle requires no electrical hookup or data output, so the tool integrates seamlessly into manual or semi-automated checks. The combination of standardised tolerance adherence and a rugged profile supports clear process control and easier training of operators, which benefits both small workshops and larger production environments. Contact Metav Werkzeuge in Emmerich for application guidance and to source the Filetta limit plug gauge MS911.170 for your quality-control needs Technical Data Article number: MS911.170 Name: Limit plug gauge G7 Manufacturer: Filetta Standard: DIN 7162 Facts Nominal size: 8 mm Fit/tolerance: G7 Special features Material: hardened steel Wear allowance on datum face Application: go/no-go checking of holes and bores FAQ What type of inspection is this gauge intended for? The limit plug gauge is intended for quick go/no-go acceptance tests of bores and holes, enabling clear pass/fail checks during incoming inspection or in-process control with the Filetta MS911.170. Is the gauge suitable for continuous production use? Yes, the hardened steel construction and the wear allowance on the datum face make the gauge suitable for repetitive use in production environments where frequent verification of bore conformity is required. Does the gauge conform to a recognised standard? The limit plug gauge is manufactured to the requirements of DIN 7162, ensuring compatibility with common metrology practices and documentation in quality systems. How is the gauge identified within inspection documentation? The tool should be recorded as Filetta MS911.170, described as a G7 limit plug gauge, 8 mm, which simplifies traceability in inspection plans and process control records. Manufacturer / Responsible: Schut Geometrische Meettechniek bv; Duinkerkenstraat 21; 9723 BN Groningen; The Netherlands; +31 50 5877877; schutnl@schut.com

Take advantage of the combination of wide standard coverage, clear dimension data and compact shop-floor usability to speed up design and inspection tasks; order the thread chart via Metav Werkzeuge or ask our consultants for application advice. Filetta Thread Chart – comprehensive thread dimension reference, clear-format A Filetta Thread Chart that provides an immediate overview of thread dimensions across common international systems, intended as a compact reference for design, production and inspection. Universal lookup for Metric, UNC, UNF, BSW Clear dimensions for Gas and BA threads Compact format for shop-floor reference Useful for design, inspection and procurement Fast decisions with consolidated thread data The core benefit of this reference is the consolidation of many standards into a single sheet. The chart lists sizes and key dimensions for metric, BSW, Gas, BSF, Pg, BA, UNC, UNF, UNEF, EG-M and EG-MF, enabling rapid decisions during setup and verification. By combining these standards, the table reduces the need to consult multiple manuals and supports faster tool selection and drawing checks. Clear labelling and organised columns turn otherwise time-consuming lookups into a quick verification step, which improves shop-floor throughput and reduces machine idle time. Improved accuracy for manufacturing and inspection Having standard dimensions collated in one reference lowers the risk of specification errors when producing threaded parts. The chart highlights pitch, nominal diameters and common conversions, making it straightforward to match taps, dies and mating components. This logical presentation supports quality control routines and assists inspectors in cross-checking parts against the correct standard. Presented as a compact, easy-to-read layout, the reference helps maintain measurement integrity without complex interpretation, supporting reliable outcomes in both small-series manufacturing and routine maintenance. Practicality for engineers, buyers and technicians Designed to serve multiple roles, the table is a practical tool for designers verifying thread fits, for procurement teams specifying the correct fasteners, and for technicians performing assembly checks. The compact format is suited to the toolroom, drawing office or bench, meaning the information is available where decisions are actually taken. With its focus on usability, the reference speeds up specification workflows and contributes directly to process efficiency—an economical improvement in daily operations. Clear communication between teams and suppliers Standardised references reduce misunderstandings between design, production and suppliers. Using one authoritative chart for common thread forms creates a single source of truth that simplifies ordering and reduces returns due to mismatched threads. The clear mapping of thread types and sizes supports consistent documentation in technical drawings and procurement lists, improving collaboration across departments and with external partners. Contact Metav Werkzeuge today for procurement support, bulk orders or specific format requests for the Filetta Thread Chart (SKU MS835.162) — expert advice and reliable delivery from Emmerich are available to help integrate this reference into your workflow Technical Data Article number: MS835.162 Name: Thread Chart (Gewindetabelle) Manufacturer: Filetta UID: MS835.162 Facts Standards included: Metric, BSW, Gas, BSF, Pg, BA, UNC, UNF, UNEF, EG-M, EG-MF Purpose: Quick lookup of thread dimensions and pitches Intended use: Design checks, inspection reference, procurement specification Special features Consolidated display of multiple international thread systems Compact, shop-floor friendly format Suited for engineers, inspectors and purchasing staff FAQ Which thread standards are covered in the chart? The chart lists common standards including metric, BSW, Gas, BSF, Pg, BA, UNC, UNF, UNEF, EG‑M and EG‑MF for immediate comparison. Is this chart suitable as a shop-floor reference? Yes, the Filetta Thread Chart (SKU MS835.162) is designed for quick lookups at the bench or in the toolroom and is optimised for practical use by technicians and inspectors. Can the table be used for procurement specifications? The consolidated dimensions and standard identifiers make the chart appropriate for clear procurement documentation and ordering lists. Does the chart include pitch and nominal diameter data? Yes, the presentation includes key dimension data such as pitch and nominal diameters to aid fitting and tool selection. Manufacturer / Responsible: Schut Geometrische Meettechniek bv; Duinkerkenstraat 21; 9723 BN Groningen; The Netherlands; +31 50 5877877; schutnl@schut.com