welche steigung hat ein m10 6h gewindelehrdorn?

Take advantage of precise, fast pass/fail checks and robust wear resistance thanks to hardened steel and DIN 7162 conformity; order the matching gauge pins directly via Metav Werkzeuge or contact our consultants for batch and inspection advice. Limit Gauge Pin — hardened-steel inspection pin, 11 mm, DIN 7162 (Filetta) The Limit Gauge Pin is a hardened-steel inspection pin designed for rapid go/no-go checks and routine dimensional control in workshops and inspection benches, compliant with DIN 7162. Hardened-steel construction for long service life Conforms to DIN 7162 for consistent tolerances 11 mm nominal diameter for standard inspection tasks Wear allowance on the good side to extend usable life Faster, reliable pass/fail inspection for production lines The compact inspection pin delivers quick go/no-go checks that reduce measuring time at control points and on the shop floor. By providing an unequivocal pass or fail condition, the pin supports efficient decision-making in both single-piece inspections and repetitive sampling routines. Conformity with DIN 7162 ensures that the nominal diameter and tolerance band are traceable to an established standard, which simplifies integration into existing inspection protocols and statistical process control. Robust build that minimises downtime Thanks to its hardened steel construction the pin withstands repeated contact without rapid degradation, while the specified wear allowance on the good side preserves the functional limit for longer. This translates into fewer replacements, reduced downtime and lower indirect costs from inspection interruptions. The hardened surface also keeps seating and mating surfaces consistent, helping to avoid false rejects that would otherwise increase rework. Practical benefits for inspection benches and gauge sets As a dedicated inspection pin, the component is optimised for quick handling and straightforward verification tasks on inspection benches and assembly jigs. The clear go/no-go characteristic reduces interpretation time for operators and speeds up routine quality checks. For quality managers the result is measurable: quicker throughput at control stations and a more consistent acceptance rate across batches. Traceability and suitability for regular quality workflows Manufactured to industry standard, the pin supports consistent batch-to-batch performance and straightforward inventory management when used in gauge sets or fixed inspection fixtures. The simple geometry and standardised tolerance regime make the item suitable for assembly audits, incoming inspections and periodic verification of tool wear, providing procurement confidence for maintenance and quality teams. Request technical advice or a batch availability check from Metav Werkzeuge in Emmerich to align delivery options with production schedules Technical Data Article number: MS911.173 Name: Limit Gauge Pin Material: hardened steel Standard: DIN 7162 Measurements / Core data Diameter: 11 mm Features / Applications Wear allowance on the good side Hardened for wear resistance Intended for go/no-go inspection tasks Category: gauge pins / inspection pins FAQ What is the nominal diameter of this inspection pin? The inspection pin has a nominal diameter of 11 mm; this specification applies to the Filetta limit gauge pin (SKU MS911.173). Is the pin suitable for go/no-go checks on assembly lines? Yes, the Filetta limit gauge pin is designed for rapid pass/fail checks and is suitable for routine assembly-line and workshop inspections. What material is used and how does it affect service life? The pin is made from hardened steel, which increases wear resistance and extends usable life compared with untreated pins. Which standard governs the pin’s tolerances? Tolerances and dimensions conform to DIN 7162, providing a recognised reference for inspection procedures. How does the wear allowance on the good side affect inspection practice? The specified wear allowance on the good side allows continued use while preserving the functional limit for a longer period, reducing unnecessary replacements Manufacturer / Responsible: Schut Geometrische Meettechniek bv; Duinkerkenstraat 21; 9723 BN Groningen; The Netherlands; +31 50 5877877; schutnl@schut.com

Take advantage of robust hardened steel construction and DIN 7162 conformity to secure reproducible bore checks; the built‑in wear allowance on the good side extends service life and simplifies limit interpretation. Order the Filetta items via Metav Werkzeuge or contact our consultants for application advice. Limit plug gauge by Filetta — hardened steel, DIN 7162, Ø 12 mm, G7 Limit plug gauge designed for rapid acceptance checks of internal diameters in production and incoming‑goods inspection Hardened steel for durable measurement Conforms to DIN 7162 standard Wear allowance on the 'go' side Reliable diameter assessment that speeds inspection throughput The limit plug gauge serves as a straightforward go/no‑go check for cylindrical bores, offering rapid verification without complex setup. Machined to a nominal diameter of 12 mm with the designation G7, the pin provides an immediate pass/fail indication that reduces inspection time compared with full dimensional measuring chains. The hardened construction minimises deformation under repeated use, which keeps the checking routine stable and helps maintain production rhythm. For shop floors and control benches where speed and repeatability matter, the gauge translates metrological specification into a clear decision at the point of measurement. Durable design that reduces replacement and downtime Made from hardened steel, the gauge withstands frequent handling and contact with metal workpieces. A specific wear allowance on the good side compensates for gradual material loss, so the go end retains acceptance criteria longer and service intervals are extended. This pragmatic feature lowers life‑cycle costs by delaying the need for reworking or replacement and by keeping inspection standards consistent. The combination of robust material and wear management supports continuous operation in industrial environments where tools are subject to intensive use. Simple integration into quality processes and documentation Conforming to DIN 7162 assists traceability in formal inspection plans and quality records. The plug gauge is suitable for routine acceptance checks in production, final inspection and incoming goods control where clear binary results are preferred. The concise form factor and unambiguous results streamline operator training and reduce human decision variance, which improves overall process capability. When used as part of a calibrated inspection set, the gauge helps to demonstrate compliance and to maintain documented control over critical bore dimensions. Practical benefits for workshop and production use This gauge simplifies everyday metrology: no complex calibration rigs are required for routine use, and the hard wearing surface minimises surface damage to both gauge and workpiece. The compact geometry facilitates access to bores in assemblies and jigged components, while the standardised dimensioning and tolerance marking enable easy cross‑referencing with drawing specifications. For manufacturing teams seeking dependable, low‑effort tools for Go/No‑Go inspection, the pin combines industrial robustness with clear operational benefits. Choose the Filetta limit plug gauge with G7 tolerance via Metav Werkzeuge for dependable in‑process checks; contact Metav Werkzeuge in Emmerich for tailored advice at info@metav-werkzeuge.com or +49 2822 7131930 Technical Data Article number: MS911.174 Product: Limit plug gauge Brand: Filetta Facts Nominal diameter: 12 mm Standard: DIN 7162 Designation: G7 Special features Material: hardened steel Wear allowance on the go side Intended for go/no‑go bore inspection FAQ What size bore is this gauge intended to check? The gauge is supplied as a 12 mm nominal limit plug gauge and is intended for quick go/no‑go checks of bores matching that nominal diameter. Is the gauge suitable for production use on a shop floor? Yes, the hardened‑steel construction and the wear allowance on the good side make the gauge robust enough for routine production and incoming‑goods inspection. How does the G7 designation influence measurement results? G7 is the designation provided with the article and identifies the tolerance fit intended for interpretation against corresponding drawing tolerances when using the plug gauge. Does the gauge comply with industry standards? The item is produced to conform with DIN 7162, facilitating inclusion in standard inspection procedures and documentation. Manufacturer / Responsible: Schut Geometrische Meettechniek bv; Duinkerkenstraat 21; 9723 BN Groningen; The Netherlands; +31 50 5877877; schutnl@schut.com

Take advantage of a durable inspection solution that combines hardened steel construction, DIN 7162 conformity and a built‑in wear allowance on the good side for predictable lifetime performance; order the Filetta limit gauge pin directly via Metav Werkzeuge or contact our consultants for application guidance. Limit gauge pin MS911.175 — hardened steel, DIN 7162 by Filetta The limit gauge pin is a precision plug gauge designed for fast verification of hole diameters and dimensional conformity in production and inspection environments. Hardened steel for durability Conforms to DIN 7162 standard Nominal 13 mm gauge pin Wear allowance on the good side Fast, reliable checks for hole diameters Limit gauge pins serve as a compact and effective tool for rapid go/no‑go assessment of bore diameters and fits. The MS911.175 from Filetta allows straightforward comparison against tolerance limits, reducing the time spent on intricate measurements and lowering the risk of finishing parts that fail inspection. By applying a simple pass/fail principle, this type of gauge pin supports continuous quality control and streamlines in‑process checks, which in turn improves throughput and reduces rework rates on the shop floor. Robust construction with predictable wear behaviour Manufactured from hardened steel, the pin provides a resistant contact surface that tolerates repeated use in production environments. The specified wear allowance on the good side means that the design accounts for gradual surface loss without compromising the verification function; users gain a longer useful service life and more predictable maintenance intervals. This wear concept avoids sudden losses of conformity and simplifies decisions about replacement or recalibration, delivering tangible savings over the component lifecycle. Standards compliance for traceable inspection routines Conformity to DIN 7162 ensures that the gauge pin integrates with existing metrology routines and adheres to recognised dimensioning rules, facilitating consistent documentation and auditability. The simple form factor makes the component easy to store alongside other inspection tools and easy to use during incoming inspections or final part control. With a clear identification such as MS911.175 and manufacturer provenance, the pin is suited for repeatable batch checks and supports a traceable quality management workflow. For precise bore verification from Filetta, contact Metav Werkzeuge for ordering and tailored application advice — Metav Werkzeuge GmbH is available at info@metav-werkzeuge.com or by phone at +49 2822 7131930 to support selection and delivery. Technical data Article number: MS911.175 Manufacturer: Filetta Material: hardened steel Size: 13 mm Standard: DIN 7162 Facts Nominal size: 13 mm Special features Wear allowance on the good side Limit/plug gauge function for go/no‑go checks Category: gauge pins / plug gauges Intended for bore diameter verification FAQ What is the primary use of this limit gauge pin? The limit gauge pin MS911.175 by Filetta is intended for quick go/no‑go checks of hole diameters and basic conformity assessments in production and inspection workflows. Which material is the gauge pin made from? The Filetta gauge pin is made from hardened steel, chosen to provide wear resistance and a stable contact surface for repeated inspections. Does this gauge pin conform to recognised standards? Yes, the component conforms to DIN 7162, which supports consistent dimensional control and integration into documented inspection routines. Manufacturer / Responsible: Schut Geometrische Meettechniek bv; Duinkerkenstraat 21; 9723 BN Groningen; The Netherlands; +31 50 5877877; schutnl@schut.com

Combining hardened steel construction, conformity to DIN 7162 and a deliberate wear allowance on the good side delivers dependable limit checking and extended service life in routine inspection tasks; order Filetta limit gauge pins via Metav Werkzeuge or consult our specialists for selection and supply advice. Limit gauge pin by Filetta — hardened steel, DIN 7162 Limit gauge pin designed for Go/No‑Go checks in production and QA environments Limit gauge pin ø 17 mm, hardened steel Conforms to DIN 7162 tolerances Wear allowance on the good side Suitable for plug and pin gauge control Dependable limit checking that stabilises production quality The solid, dimensionally stable construction supports fast, repeatable inspections on the shop floor and in quality control. Built from hardened steel, this pin maintains its nominal size under cyclic use, which reduces the risk of false rejects and rework. Conformity to DIN 7162 provides an objective reference for acceptance testing and helps to harmonise checks across suppliers and production lines, improving throughput and lowering non‑conforming parts per million. Reduced downtime thanks to a wear‑compensated design The integrated wear allowance on the good side extends the usable life of each pin by allowing controlled material loss while preserving the accept signal for Go checks. For maintenance planners and inspectors this means fewer replacements and more predictable tool cycles. The design philosophy emphasises long‑term precision, so inspection intervals can be scheduled on condition rather than by conservative fixed replacement, saving operational time without compromising measurement integrity. Practical suitability for workshop and gauge sets Manufactured for routine limit inspection duties, the pin is compact and straightforward to integrate into existing gauge sets and fixtures. The simple geometry supports quick insertion for plug checks and is compatible with standard bench routines. For technical procurement and production engineering teams, the combination of material choice and standard compliance provides a reliable basis for procurement decisions and spares planning, while Metav Werkzeuge can advise on kit assembly and batch supply options. For specification support or stock availability of Filetta limit gauge pins (MS911.179) contact Metav Werkzeuge for a tailored recommendation at info@metav-werkzeuge.com or call +49 2822 7131930 Technical Data Article number: MS911.179 Manufacturer: Filetta Size / Diameter: 17 mm Material: hardened steel Standard: DIN 7162 Special feature: wear allowance on the good side Specifications Diameter: 17 mm Design & Features Category: limit gauge pin / plug gauge Intended use: Go/No‑Go limit checking and quality control Application area: production inspection, incoming goods control FAQ What is this pin used for in production? This limit gauge pin (Filetta, MS911.179) is used for Go/No‑Go checks and routine limit inspections to verify bore and fit dimensions on parts. Does the pin meet a recognised standard? Yes, the Filetta pin complies with DIN 7162, ensuring standardized tolerance classes for limit gauges. How does the wear allowance affect service life? The built‑in wear allowance on the good side prolongs usable life by permitting controlled wear while maintaining the Go limit, reducing replacement frequency. Can Metav Werkzeuge supply matching gauge sets or replacements? Metav Werkzeuge can advise on compatible gauge sets and supply quantities; the Filetta MS911.179 can be ordered as part of a coordinated inspection kit. Manufacturer / Responsible: Schut Geometrische Meettechniek bv; Duinkerkenstraat 21; 9723 BN Groningen; The Netherlands; +31 50 5877877; schutnl@schut.com

Take advantage of DIN 7162 conformity, hardened steel construction and the integrated wear allowance on the go side for dependable bore verification. Order this limit plug gauge directly via Metav Werkzeuge or contact our consultants for application advice. Limit plug gauge G7 – 20 mm, hardened steel (DIN 7162) by Filetta A limit plug gauge G7 designed for rapid go/no-go checks of cylindrical bores in production and inspection environments Hardened steel for long service life Manufactured to DIN 7162 standard Wear allowance on the go side Suitable for bore verification and QC Reliable measurements through recognised standards The gauge is manufactured to DIN 7162, which ensures consistent dimensions and interchangeability across inspection routines. For a nominal size of 20 mm, the plug gauge provides an immediate go/no-go decision, eliminating lengthy measurement evaluation processes. This standard-led approach supports efficient quality control, reduces scrap rates and shortens inspection cycles by delivering clear, repeatable outcomes at every station. Durable construction that reduces downtime Made from hardened steel, the instrument tolerates repeated use on the shop floor while maintaining dimensional stability. The incorporated wear allowance on the go side compensates for gradual material loss during routine checking, extending the service life before any rework or replacement becomes necessary. This pragmatic design reduces unplanned stoppages and lowers total cost of ownership by keeping maintenance intervals predictable. Practical integration for workshop and production use Sized for common bore checks, the plug gauge is ideal for quick verification during assembly, final inspection or incoming goods control. Its straightforward go/no-go functionality accelerates throughput without requiring complex measuring equipment or extensive operator training. The robust design and adherence to DIN 7162 make it suitable for use in machine shops, tool rooms and quality laboratories where rapid, trustworthy pass/fail decisions are required. Reference: model MS911.182 for ordering and stock enquiries. Contact Metav Werkzeuge for expert advice on integrating Filetta limit plug gauges (DIN 7162) into existing inspection routines and to secure reliable supply from our Emmerich warehouse Technical Data Article number: MS911.182 Material: hardened steel Standard: DIN 7162 Size: 20 mm Facts Diameter: 20 mm Special features Wear allowance on the go side Designed for go/no-go checks Robust hardened-steel construction FAQ What is the primary use of this limit plug gauge? This limit plug gauge is intended for fast go/no-go verification of cylindrical bores, providing a clear pass/fail result for production and inspection tasks. What material is the gauge made from and why does it matter? The gauge is produced from hardened steel, which ensures wear resistance and dimensional stability under frequent use, supporting reliable long-term measurements. Which standard does the product comply with? Manufactured to DIN 7162, the gauge meets recognised dimensional and manufacturing criteria for plug gauges used in industrial quality control. How does the wear allowance affect inspection intervals? The wear allowance on the go side compensates for gradual abrasion, extending useful life and allowing longer intervals between gauge replacement or rework; the item is listed as MS911.182 for ordering and inventory reference. Manufacturer / Responsible: Schut Geometrische Meettechniek bv; Duinkerkenstraat 21; 9723 BN Groningen; The Netherlands; +31 50 5877877; schutnl@schut.com

Take advantage of the combination of hardened steel construction, DIN 7162 compliance and an integrated wear allowance on the Go side for dependable go/no-go checks in routine inspection. Order the Filetta limit plug gauge directly via Metav Werkzeuge or consult our specialists for application advice. Filetta Limit Plug Gauge G7 — Hardened steel, DIN 7162 A Limit plug gauge for rapid go/no-go verification of small bores during incoming inspection and process control. Hardened steel for long service life Complies with DIN 7162 inspection standard Wear allowance on the Go side Consistent dimensional checks for production quality The Filetta limit plug gauge delivers a compact, robust solution for fast pass/fail inspection of cylindrical bores. Manufactured from hardened steel, the gauge resists wear and maintains dimensional integrity under frequent use, which supports consistent precision in repetitive checks. Conformance with DIN 7162 ensures the gauge geometry and tolerances match established industrial expectations, simplifying documentation and traceability in standardised inspection routines. The incorporated wear allowance on the Go side extends service intervals by permitting controlled material removal while preserving functional acceptance limits. Practical benefits for shop-floor and inspection benches Designed for efficient routine use, this gauge streamlines the decision step between acceptable and non‑conforming workpieces with unmistakeable go/no-go feedback. The compact format suits bench inspection and dedicated control stations where speed and reliability matter; the simple plug engagement avoids time‑consuming measurements while reducing interpretation errors. As a tactile reference tool, the gauge complements digital instruments and micrometres by providing an immediate mechanical check that is quick to apply and straightforward to record in inspection logs. Durable design that lowers operational risk Material choice and standardised manufacture reduce uncertainty: hardened steel construction offers high wear resistance, while the standard compliance reduces the need for custom verification procedures. The wear allowance on the Go side is a practical feature that keeps the gauge serviceable for longer, lowering total cost of ownership and helping maintain process capability between calibrations. For workshops and production lines requiring reproducible go/no-go results, this gauge is a pragmatic component of a robust quality-control toolkit. Contact Metav Werkzeuge today to specify the right Filetta limit plug gauge (MS911.167) for the inspection tasks and to arrange delivery from Emmerich or further technical consultation Technical data Article number: MS911.167 Product: Limit plug gauge Material: Hardened steel Facts Size: 5.5 mm Standard: DIN 7162 Special features Wear allowance on the Go side FAQ What is the primary purpose of this limit plug gauge? The Filetta limit plug gauge MS911.167 is designed for quick go/no-go verification of small bores to determine conformity during incoming inspection and in-process checks. Which material is the gauge made from and why does it matter? Manufactured from hardened steel, the gauge resists wear and maintains dimensional stability, ensuring reliable pass/fail checks over extended use. Does the gauge follow a recognised standard? Yes. The gauge conforms to DIN 7162, which standardises geometry and tolerances for plug-style limit gauges used in industrial inspection. How does the wear allowance affect maintenance intervals? The built-in wear allowance on the Go side permits controlled degradation before the gauge reaches out-of-tolerance condition, extending usable life and reducing the frequency of replacement. Manufacturer / Responsible: Schut Geometrische Meettechniek bv; Duinkerkenstraat 21; 9723 BN Groningen; The Netherlands; +31 50 5877877; schutnl@schut.com

Take advantage of precise, rapid thread identification combined with a lightweight, corrosion‑resistant design for smoother assembly and inspection workflows. The set’s anodised aluminium gauges and organised plastic case enable fast checks of common metric threads; order directly via Metav Werkzeuge or contact our consultants for technical advice. Gewindekontrollsatz MS910.425 — Thread gauge set (anodised aluminium, metric) by Filetta The Gewindekontrollsatz is a compact identification set for metric internal and external threads, intended for workshop inspection, maintenance and assembly tasks Anodised aluminium construction For metric internal and external threads Supplied in a durable plastic case 20-piece set covering M3–M24 Faster thread identification for everyday production The gauge set accelerates routine identification and basic verification of metric screw threads, reducing time lost on uncertain assembly decisions. Thanks to the wide size range from M3 to M24 and the inclusion of both internal and external gauges, common pitches and diameters can be checked on the spot. The primary benefit is operational efficiency: fewer stoppages during assembly and faster throughput in inspection processes. The solid, repeatable fit of each gauge supports reliable visual and tactile confirmation of thread form and pitch. Lightweight, corrosion‑resistant construction for frequent handling Being manufactured from anodised aluminium, the components combine durability with low weight, making them comfortable for daily use in bench and field environments. The surface treatment helps resist wear and corrosion, preserving the profile of each gauge and extending service life. Packaged in a plastic case that keeps items organised and protected, the set is easy to transport between workstations and to store without risk of damage to the thread contours. This construction promotes consistent handling with minimal maintenance. Practical scope for incoming inspection and maintenance The set is designed as a practical aid for incoming goods inspection, routine maintenance and quick on‑machine checks. It is intended for identification and coarse verification rather than micrometric measurement: the gauges confirm thread form and common pitch compatibility to avoid assembly errors. For workshops that need straightforward, rapid decisions—accept, reject, or select the correct fastener—this solution reduces rework and saves time in quality control routines while supporting a smooth production flow. Clear contents and metric compatibility for everyday sizes Contents include gauges for standard metric sizes that are frequently encountered in mechanical and electrical assemblies. The 20‑piece composition covers a typical workshop spectrum from smaller machine screws up to larger bolts used in fixtures and assemblies. This configuration makes the set suitable as a bench reference or as part of a mobile inspection toolkit, supporting technicians who require quick identification without complex measurement equipment. The lightweight profiles and organised layout aid rapid selection and return to service. For reliable metric thread identification from Filetta choose Metav Werkzeuge — contact our Emmerich specialists for tailored advice and fast supply via info@metav-werkzeuge.com or by phone at +49 2822 7131930 Technical Data Article number: MS910.425 Manufacturer: Filetta Material: anodised aluminium Thread type: metric Set: 20 pieces Facts Sizes included: M3x0.5, M4x0.7, M5x0.8, M6x1.0, M8x1.0, M8x1.25, M10x1.0, M10x1.25, M10x1.5, M12x1.25, M12x1.5, M12x1.75, M14x1.5, M14x2.0, M16x1.5, M16x2.0, M20x1.5, M20x2.5, M24x2.0, M24x3.0 Suitable for: internal and external threads Special features Identification and basic verification of metric threads Lightweight, corrosion‑resistant anodised finish Supplied in a protective plastic case Compact, workshop‑oriented organisation FAQ What is the primary purpose of this gauge set? The Gewindekontrollsatz MS910.425 by Filetta serves for quick identification and basic verification of metric internal and external threads to support inspection and assembly decisions. Can the gauges measure thread tolerances precisely? The set is intended for identification and coarse verification rather than precision tolerance measurement; for high‑accuracy checks, use calibrated metrology instruments. Which sizes are covered by the set? The set contains 20 gauges covering common metric sizes from M3x0.5 up to M24x3.0, suitable for many workshop and maintenance tasks. Is the material suitable for frequent workshop use? Yes — the gauges are made from anodised aluminium, providing a balance of lightweight handling and corrosion resistance for regular use. Does the set include a case for transport and storage? The Filetta MS910.425 is supplied in a durable plastic case that keeps each gauge protected and organised for transport between workstations. Manufacturer / Responsible: Schut Geometrische Meettechniek bv; Duinkerkenstraat 21; 9723 BN Groningen; The Netherlands; +31 50 5877877; schutnl@schut.com

Combine ISO 286‑2 compatibility with an instant lookup of more than 6,400 tolerance values for reliable design decisions and consistent inspection results — order the Tolerance table directly via Metav Werkzeuge or contact our consultants for tailored advice. Tolerance table — ISO 286‑2 reference chart (up to 500 mm) by Filetta The Tolerance table is a compact reference chart for immediate reading of tolerance values and fits according to ISO 286‑2, intended for engineering, quality control and workshop use. ISO 286‑2 compatibility up to 500 mm Over 6,400 tolerance entries Immediate reading for fits and tolerances Suitable for internal and external dimensions Faster decisions with standardised tolerance data The reference matrix provides a single, standardised source for clearance, transition and interference fits, reducing time spent searching dispersed tables. With direct mapping to ISO 286‑2 and coverage to 500 mm, the chart supports rapid verification of nominal sizes and tolerances, enabling engineers to confirm fit classes and tolerance zones without complex calculations. The compact presentation of tolerance values accelerates decision-making in design reviews and first-off inspections. Clear guidance for assemblies and inspection routines Presented as an immediate-reading table, the chart removes ambiguity when selecting shaft and hole tolerances for bearings, housings or shafts. The organised layout helps translate ISO class designations into usable limits for production and QC, so tolerance checks can be executed consistently on the shop floor. Where traceable documentation is needed, the dataset of 6,400+ entries serves as a reliable reference for specifying fits in drawings and inspection protocols. Practical benefits for workshops and design offices Adopting a single reference chart reduces errors caused by cross-referencing multiple sources and supports faster training of technicians and junior engineers. The concise format is optimised for routine tasks — from tolerance verification during assembly to prepare-for-inspection checks — and complements digital workflows where a human-readable standard is required alongside CAD and measurement reports. The association with Filetta denotes a focused tool for metrology professionals who value clarity and compliance. For standards-compliant tolerance reference and rapid integration into inspection routines, request the Filetta Tolerance table from Metav Werkzeuge today — contact our specialists at info@metav-werkzeuge.com or call +49 2822 7131930 to discuss suitability for specific applications. Technical Data Article number: MS835.163 Name: Tolerance table Brand: Filetta Label: Toleranztabelle Facts Standard: ISO 286‑2 Scope: up to 500 mm Entries: >6,400 tolerance values Special features Immediate-reading table of tolerance values and fits Includes internal and external dimensions Data suited to engineering and workshop reference FAQ What standard does this reference follow? The Filetta Tolerance table follows ISO 286‑2, providing standardised tolerance classes and zones for engineering use. Up to which nominal size are tolerance values provided? The chart covers nominal sizes up to 500 mm, with entries for both internal and external dimensions. How extensive is the dataset included in the chart? The reference contains more than 6,400 tolerance values for quickly determining fits and limits. Is this chart suitable for shop‑floor inspection tasks? Yes — the immediate‑reading format makes the chart suitable for routine inspection, assembly checks and specification clarification in the workshop. Can the table help when specifying fits on technical drawings? The dataset translates ISO class designations into practical limit values, supporting clear specification of fits and tolerances on drawings. Filetta: Manufacturer / Responsible: Schut Geometrische Meettechniek bv; Duinkerkenstraat 21; 9723 BN Groningen; The Netherlands; +31 50 5877877; schutnl@schut.com