Secure and precise workholding for metalworking productivity
Workholding devices such as workpiece clamps and chuck systems provide absolute positional stability and vibration damping during milling, turning, drilling and grinding, ensuring parts remain free of play under high CNC cutting and feed forces. By transferring clamping loads into the machine table or spindle without deforming the component, a well engineered workholding solution improves machining accuracy, surface finish and process reliability while reducing set-up times. Modular systems from machine vices and chucks to zero-point systems and specialised fixtures enable fast changeovers and support both serial and single-part production, delivering consistent clamping force, repeatability and enhanced throughput.
140° Pneumatic Clamp With Vertical Handle, 1200 N Clamping Force, Zinc-Plated - Kukamet
Reliable fixation and compact design make this pneumatic clamp an efficient choice for repetitive assembly and machining tasks: 1200 N clamping force, 1400 N holding force and zinc‑plated construction ensure secure, corrosion‑resistant performance and long service life. Order the 651 directly via Metav Werkzeuge or ask our consultants for application advice. Kukamet 651 Pneumatic Clamp — vertical handle, 1200 N clamping force The 651 pneumatic clamp is a compact, zinc‑plated fixture for secure workpiece holding in assembly and machining, equipped with a vertical handle and vertical foot mounting. Vertical handle for ergonomic operation Zinc‑plated corrosion protection 1200 N clamping force, 1400 N hold strength Reliable clamping for continuous production The pneumatic actuation delivers consistent, repeatable clamping that reduces setup variation and minimises rework. With a rated 1200 N clamping force and 1400 N holding force, the device secures components reliably during handling and machining operations. Pneumatic actuation ensures rapid cycle times and predictable force application, which supports higher throughput and better first‑pass yields. The compact actuator mechanism also keeps the fixture footprint small, aiding dense production layouts. Durable finish and compact mounting for workshop use A zinc‑plated finish provides robust corrosion resistance in standard workshop environments, extending service intervals and reducing replacement rates. The clamp’s vertical foot mounting and fixed 90° angle permit stable right‑angle installation on jigs, pallets or production benches, while the lightweight construction (approximately 0.62 kg) simplifies integration into modular fixtures. These attributes combine to reduce downtime and support reliable long‑term performance in industrial settings. Ergonomic operation that speeds routine tasks The vertical handle is designed for straightforward, ergonomic actuation, allowing operators to engage and release the clamp swiftly with minimal fatigue. This ergonomic detail translates into measurable time savings across repeated cycles and contributes to improved workplace comfort—important in busy assembly environments where speed and operator wellbeing matter. The vertical orientation also keeps the handle clear of adjacent tooling, improving accessibility in compact assemblies. Flexible application and straightforward installation Engineered for fixture and jig use, this pneumatic clamping device suits assembly, welding and light machining tasks that require secure, repeatable holding at a right angle. The compact design and established mounting pattern support integration into existing tooling systems without major redesign. Supplied as a single‑unit SKU 651-2-H, the clamp offers a practical combination of strength, corrosion protection and low mass that benefits both bespoke fixtures and volume production jigs. Order the Kukamet 651 via Metav Werkzeuge for dependable clamping solutions and expert advice—contact Metav Werkzeuge at info@metav-werkzeuge.com or call +49 2822 7131930 for specification guidance and application support. Technical data Article number: 651-2-H GTIN: 8682843521632 Manufacturer: Kukamet Facts Weight: 0.62 kg Max clamping force: 1200 N Max holding force: 1400 N Angle: 90° Special features Material: zinc‑plated Mounting: vertical foot Handle: vertical eClass: 21021004 ETIM: EC011973 FAQ What clamping and holding forces does this clamp provide? The Kukamet 651 pneumatic clamp delivers a maximum clamping force of 1200 N and a holding force of 1400 N for secure workpiece fixation. How is the clamp installed on a fixture? The unit is designed for vertical foot mounting with a fixed 90° orientation; the SKU 651-2-H fits standard right‑angle fixture arrangements. What surface finish and durability can be expected? The clamp is zinc‑plated, providing corrosion resistance suitable for typical workshop conditions and extending the service life of the component. Is the handle suited to high‑cycle operations? Yes. The vertical handle design on the 651 supports quick, ergonomic actuation that helps maintain cycle speed and reduce operator fatigue during repetitive use. Which production areas benefit most from this clamp? The device is intended for assembly jigs, welding fixtures and light machining applications where compact, repeatable clamping at right angles is required; the Kukamet clamp is specified as SKU 651-2-H. Manufacturer: Kukamet Fevzi Çakmak Mah.10644 Sk. No:61-63 42050 Karatay / KONYA TÜRKİYE / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com
141mm Vertical Clamp 3,300N Holding Force, 3,000N Thrust, Angled Base, Hardened Blackened Finish - Kukamet
Compact, robust and easy to integrate: the Kukamet vertical clamp delivers a solid holding arm, a 141 mm reach and a reliable holding force up to 3,300 N for stable workholding in production and jigs. Benefit from a compact footprint and a black blued finish that resists workshop wear. Order the vertical clamp directly via Metav Werkzeuge or consult our specialists for application advice. Vertikalspanner 213 — Vertical lever clamp with 141 mm arm and angle base (Kukamet) Vertikalspanner 213 is a vertical lever clamp engineered for secure fixture work, combining a robust holding arm with a compact mounting footprint. Solid holding arm for stable clamping 141 mm reach for compact fixtures Angle base for secure mounting Up to 3,300 N holding force Consistent, high holding force for repeatable production The clamp provides a holding force of 3,300 N with an actuation pressure of 3,000 N, ensuring consistent restraint of workpieces during repetitive processes. This level of force reduces slippage and rework, improving throughput in assembly, welding or machining jigs. The mechanical design converts lever motion into dependable clamping action, delivering industrial-grade repeatability without complex pneumatic systems. Small footprint and straightforward mounting for tight fixtures With a 141 mm arm and an angle base, the device integrates into compact jigs and bench setups while maintaining accessibility to the clamped area. The low mass—approximately 0.972 kg—keeps additional load on moving fixtures minimal and helps preserve cycle dynamics. Mounting on an angled foot simplifies alignment and makes the clamp suitable for constrained layouts where space optimisation is essential. Robust construction and workshop-capable finish A solid holding arm and a black blued finish provide mechanical strength and increased resistance to corrosion and handling wear. The sturdy build supports long-term use in production environments and reduces maintenance intervals compared with lighter, less rigid alternatives. Supplied design and materials focus on pragmatic longevity so that fixtures remain stable and predictable over many cycles. Contact Metav Werkzeuge for tailored advice on integrating the Kukamet vertical clamp 213 into existing jigs and fixtures; phone +49 2822 7131930 or email info@metav-werkzeuge.com for specification support and ordering assistance Technical data Article number: B213-4-D-C2 GTIN: 8680731508024 Manufacturer: Kukamet Facts Weight: 0.972 kg Arm length: 141 mm Max holding force: 3,300 N Max actuation/pressing force: 3,000 N eClass: 21041717 ETIM: EC011973 Special features Mounting: angle base (Winkelfuß) Finish/material: black blued Solid holding arm Application trigger: lever clamp Category: Clamps (Spanner) FAQ What maximum holding force does the Vertikalspanner 213 provide? The Vertikalspanner 213 delivers a maximum holding force of 3,300 N as specified for reliable workpiece restraint. What is the reach of the clamp arm? The clamp has an arm length of 141 mm, giving a compact reach suitable for tight fixtures and jigs. How is the clamp mounted in a fixture? Mounting is via an angle base (Winkelfuß), allowing secure attachment to plates and angled surfaces for stable integration. What is the finish and weight of the vertical clamp? The Kukamet vertical clamp has a black blued finish and a weight of approximately 0.972 kg, offering a durable surface and low added mass. Which article number and GTIN identify this product? The SKU is B213-4-D-C2 and the GTIN is 8680731508024 for ordering and inventory reference. Manufacturer: Kukamet Fevzi Çakmak Mah.10644 Sk. No:61-63 42050 Karatay / KONYA TÜRKİYE / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com
143,5mm Zentrierspitze Pro Genauigkeitsausführung Verlängerte Laufspitze 60° Spitzenwinkel MK5 Rundlauf 0,005 mm Drehzahl 3000 min⁻¹ - RÖHM
Zentrierspitze HVL Pro MK5 mit verlängerter Laufspitze RÖHM – Zentrierspitze Die Zentrierspitze HVL Pro MK5 mit verlängerter Laufspitze RÖHM ist eine Pro‑Genauigkeitsausführung zur präzisen Werkstückzentrierung bei hochbelasteten Drehprozessen. Pro‑Genauigkeit mit Rundlauf ≤ 0,005 mm Für Werkstücke bis 1200 kg Belastbarkeit MK5 Schaft für standardisierte Spannfutteraufnahme Verlängerte Laufspitze für tiefere Zentrierung Geeignet bis 3000 min⁻¹ Drehzahl Präzision, die Produktionsprozesse reduziert Die Zentrierspitze bietet eine Rundlaufabweichung von maximal 0,005 mm, was die Rüstzeiten und Nacharbeit spürbar reduziert. Durch die Kombination aus geringer Toleranz und stabiler Bauform lässt sich die Wiederholgenauigkeit beim Drehen verbessern, wodurch Ausschussquoten sinken und die Ausbringung steigt. Die Möglichkeit, Werkstücke bis zu 1200 kg aufzunehmen, macht die Ausführung ideal für Serienfertigung und Einzelteile mit hohem Gewicht. Robuste Anschlusslösung und einfache Integration Mit der Schaftausführung MK5 ist die Aufnahme kompatibel zu gängigen Drehmaschinen und Spannfuttern, was die Integration in vorhandene Produktionslinien vereinfacht. Der Schaftdurchmesser 44,399 mm und der Gehäusedurchmesser 88,5 mm sorgen für sichere Sitzfestigkeit und eine ausgewogene Masseverteilung. Der Spitzenwinkel 60° unterstützt standardisierte Zentrieraufgaben; die Spitzenlänge 65 mm ermöglicht tiefere Zentrierpositionen ohne Modifikation der Maschine. Einsatzbereiche und Maschinenvorteile Für Anwender in Werkzeugbau, Lohnfertigung und Maschinenbau bietet die HVL Pro gezielte Vorteile: hohe Belastbarkeit, stabile Zentrierung und reduzierte Vibrationsanfälligkeit bei Schnittkräften. Die zulässige Drehzahl bis 3000 min⁻¹ gewährleistet sicheren Betrieb bei typischen Zerspanparametern. Durch die verlängerte Laufspitze eignet sich das Produkt besonders für tiefgezogene oder langgestreckte Werkstücke, bei denen konventionelle Spitzen an ihre Grenzen stoßen. Wir empfehlen den Kauf der Zentrierspitze HVL Pro MK5 über Metav Werkzeuge; bei technischen Fragen steht das Team per eMail info@metav-werkzeuge.com oder Telefon +49 2822 7131930 zur Verfügung Leistungsmerkmale Artikelnummer: 4000832084NW Marke: RÖHM Typ: Pro - Genauigkeitsausführung, verlängerte Laufspitze Produktart: Zentrierspitze Verpackungseinheit: 1 Daten Durchmesser: 40 mm Ausladung: 143,5 mm Gewicht: 4,8 kg Schaftdurchmesser: 44,399 mm Spitzenlänge: 65 mm Spitzenwinkel: 60° Drehzahl max.: 3000 min⁻¹ Werkstückgewicht max.: 1200 kg Rundlaufabweichung max.: 0,005 mm Gehäusedurchmesser: 88,5 mm Besonderheiten Schaftausführung: MK5 Ausführung: Pro - Genauigkeitsausführung Verlängerte Laufspitze UID: 4000832084NW FAQ Wie präzise ist die Zentrierspitze in der Praxis? Die Zentrierspitze HVL Pro MK5 von RÖHM erreicht eine Rundlaufabweichung von maximal 0,005 mm, was für hohe Wiederholgenauigkeit bei Serien und Einzelteilen sorgt und Nacharbeit reduziert. Für welche Maschinen ist die HVL Pro MK5 geeignet? Die HVL Pro MK5 ist für Drehmaschinen und Spannfutter mit MK5‑Aufnahme ausgelegt und lässt sich unkompliziert in bestehende Produktionslinien integrieren. Welche maximale Drehzahl darf verwendet werden? Die zulässige maximale Drehzahl beträgt 3000 min⁻¹; innerhalb dieses Bereichs bleibt die Zentrierspitze formstabil und sicher im Betrieb. Kann die Spitze schwere Werkstücke tragen? Ja, die Konstruktion erlaubt Werkstückgewichte bis zu 1200 kg, wodurch die HVL Pro MK5 auch für schwerere Bauteile in der Serienfertigung geeignet ist. Welcher Spitzenwinkel wird verwendet und was bedeutet das für die Praxis? Der Spitzenwinkel beträgt 60°, ein Industriestandard, der zuverlässige Zentrierung bei typischen Drehprozessen gewährleistet. Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
143mm Horizontal Clamp With Massive Holding Arm And Safety Lock, Vertical Base - Kukamet
Combining a robust 143 mm holding arm, galvanised corrosion protection and up to 1,000 N clamping force, this horizontal lever clamp delivers reliable workholding and long service life; order the 112-1-D-L-C3 directly via Metav Werkzeuge or consult our specialists for application advice. Kukamet 112 Horizontal Lever Clamp — galvanised finish, 143 mm arm Kukamet 112 is a horizontal lever clamp designed for secure fixture work in jigs and small production setups with a vertical-foot mount for upright attachment Massive 143 mm holding arm Galvanised corrosion protection Clamping force up to 1,000 N Vertical-foot mount at 90° Consistent clamping performance for production environments The clamp is engineered to provide repeatable clamping force for assembly and fixture tasks. With a maximum holding force of 1,000 N and a maximum pressing force of 850 N, the device ensures components remain fixed during machining, welding or inspection. The 90° orientation and horizontal toggle action deliver fast engagement and release, reducing cycle time and improving throughput. The result is a measurable improvement in process stability where reliable positioning is essential. Space-conscious mounting and straightforward operation A vertical-foot mounting arrangement keeps the base compact while allowing the lever to operate in a horizontal plane, making this clamp suitable for confined jig fixtures. The 143 mm arm provides effective reach without adding unnecessary bulk, and the simple toggle mechanism is operated with minimal handling effort. The galvanised finish resists corrosion in standard workshop environments, ensuring low maintenance and consistent functioning over repeated cycles. Robust construction and integrated safety features for daily use Built with a massive holding arm and an integrated safety locking function, the clamp combines mechanical strength with operational security. Galvanised steel construction contributes to long-term durability and helps prevent surface deterioration under typical workshop conditions. The light overall mass supports easy retrofitting into existing jig systems while the reliable locking reduces the risk of accidental release, improving workplace safety and component protection when clamping forces are applied. Secure production workflows with Kukamet's robust horizontal lever clamp 112 — contact Metav Werkzeuge in Emmerich for tailored application advice and reliable supply at info@metav-werkzeuge.com or +49 2822 7131930 Technical data SKU: 112-1-D-L-C3 GTIN: 8680731505429 ETIM: EC011973 ECLASS: 21041719 Facts Arm length: 143 mm Angle: 90° Weight: 0.1 kg Maximum holding force: 1,000 N Maximum pressing force: 850 N Special features Material: galvanised steel Mounting: vertical foot Design: horizontal lever / toggle clamp Safety locking mechanism Massive holding arm FAQ How much clamping force does the clamp provide? The Kukamet 112 horizontal lever clamp offers a maximum holding force of 1,000 N and a maximum pressing force of 850 N, suitable for many fixture tasks. Is the clamp suitable for use in humid workshop environments? Yes, the galvanised steel finish on the Kukamet 112 provides corrosion resistance for standard workshop conditions. What mounting option is used for this clamp? The clamp features a vertical-foot mount designed for upright attachment within jigs and fixtures. Can the 143 mm arm reach components in tight jigs? The 143 mm arm length gives a balance of reach and compactness, making it well suited to confined fixture layouts. Does the clamp include a safety mechanism to prevent accidental release? Yes, the Kukamet 112 incorporates a safety locking function to reduce the risk of unintended opening under load. Manufacturer: Kukamet Fevzi Çakmak Mah.10644 Sk. No:61-63 42050 Karatay / KONYA TÜRKİYE / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com
143x550x140mm Hydraulic Machine Vice With Extra Large Opening 0-265 mm, 4500 kgf Clamping Force - Vertex
Benefit from a robust cast iron construction, an extra-large 0–265 mm opening and a consistent 4,500 kgf clamping force to secure a smooth production flow and minimise rework. Order the Hydraulic Machine Vice VMCH-5 directly via Metav Werkzeuge or ask our consultants if needed. Hydraulic Machine Vice VMCH-5 — Hydraulic clamping with 0–265 mm opening (Vertex) A robust Hydraulic Machine Vice VMCH-5 engineered for secure clamping in machining environments, featuring an extra-large opening and high clamping force for heavy-duty work Hydraulic clamping action for secure hold Extra-large 0–265 mm opening capacity 4,500 kgf clamping force for heavy work Cast iron construction, mass 45.5 kg Built for heavy-duty clamping and stability The vice is manufactured from cast iron, giving it substantial mass and vibration damping for stable machining. The heavy construction, at 45.5 kg, reduces movement under load, which directly benefits surface finish and tool life when working on demanding operations. Because the body is rigid and well balanced, the clamp keeps workpieces steady during milling, drilling or turning, translating into fewer set-ups and consistent cycle times for production environments. Consistent clamping force for repeatable results Hydraulic operation delivers a reliable, even hold across the jaw faces, with a rated 4,500 kgf clamping force that secures components for heavy cutting conditions. The unit's precision 0.01 mm specification supports tight tolerances and repeatability: this figure refers to the vice’s repeatability and positional consistency, helping to maintain part accuracy across batches. Clear specification of force and tolerance makes process planning and fixture design straightforward for production engineers. Flexible workpiece handling with an extra-large opening An opening range of 0–265 mm accommodates a broad spectrum of component sizes, reducing the need for multiple fixtures and increasing shop-floor flexibility. The broad jaw travel suits both compact parts and larger workpieces, allowing a single clamping solution to cover varied tasks. For workshops that handle mixed production runs, this capacity minimises changeover time and simplifies tooling inventories. Compact footprint, straightforward integration With compact external dimensions of 143 x 550 x 140 mm, the vice fits comfortably on most machine tables while providing substantial clamping capability. The hydraulic design offers controlled clamping force without manual over-tightening, improving operator safety and consistency. The combination of robust materials and a compact layout supports straightforward integration into CNC machines and manual mills where precision and uptime are priorities. Contact Metav Werkzeuge for tailored clamping advice and rapid supply from Emmerich — ask about the VMCH-5 and its fit for specific machining tasks Technical data SKU: VMCH-5 GTIN: 4061905089633 ETIM: EC002173 EClass: 21020601 Brand: Vertex Core technical data Opening: 0–265 mm Clamping force: 4,500 kgf Weight: 45.5 kg Accuracy: 0.01 mm Dimensions: 143 x 550 x 140 mm Materials & special features Material: cast iron Type: Hydraulic Model designation: Hydraulic machine vice with extra-large opening FAQ What clamping range does the vice cover? The Hydraulic Machine Vice VMCH-5 by Vertex provides an opening range of 0–265 mm, suitable for a wide variety of component sizes. Is the vice suitable for cast iron workpieces? Yes, the vice is made from cast iron and is appropriate for machining cast iron components, offering the rigidity required for stable cutting conditions. What clamping force can be expected from the unit? The vice delivers a rated 4,500 kgf clamping force, giving secure holding for heavy-duty machining tasks. How precise and repeatable is the clamping position? The vice is specified with a 0.01 mm accuracy figure, indicating high repeatability for serial production and precision setups. What are the physical dimensions and weight of the vice? External dimensions are 143 x 550 x 140 mm, and the vice has a mass of 45.5 kg, combining compact footprint with substantial stability. Manufacturer: Vertex Machinery Works Co., Ltd.; No. 296, Sec. 1, Feng Shih Road, Fengyuan District, Taichung City 420, Taiwan
144mm Vertical Clamp 750N Closing Force, 1000N Holding Force, Zinc Plated, Horizontal Base, Massive Arm Lock - Kukamet
The galvanised construction, massive holding arm and integrated safety locking mechanism combine to deliver reliable, repeatable clamping with a holding capacity up to 1,000 N and clamping force of 750 N; order the clamp directly via Metav Werkzeuge or request guidance from our consultants for seamless integration. Vertical toggle clamp 211 — galvanised with 144 mm holding arm (Kukamet) The vertical toggle clamp 211 is a compact workholding solution for fixture and assembly applications, mounted on a horizontal base and designed to combine secure clamping with low-profile installation. Galvanised steel body for corrosion resistance Solid 144 mm holding arm with robust support Safety locking mechanism for secure clamping Holding force up to 1,000 N, clamping 750 N Consistent clamping that keeps production moving Engineered for dependable fixture work, the clamp offers a galvanised finish that resists corrosion in workshop environments and a solid holding arm that minimises flex under load. The mechanical design delivers a clear, measurable benefit: stable workpieces and fewer rejects. With a rated holding force of 1,000 N and a maximum clamping force of 750 N, the device is suitable for light to medium assembly and jigging tasks where repeatability and safety are priorities. The robust latch reduces the need for frequent adjustments, supporting continuous production runs with predictable outcomes. Easy installation and compact footprint for flexible fixtures Designed with a horizontal base for straightforward mounting, the clamp integrates into bespoke jigs and modular fixtures without complex rework. The 144 mm arm provides a useful reach while keeping the overall footprint compact and lightweight at 0.155 kg, allowing multiple units to be deployed without overburdening the fixture. This compactness shortens setup times and simplifies positioning in tight assemblies, which benefits both single-station work and small-batch manufacturing where agility and quick changes matter. The mechanical simplicity also aids toolroom maintenance and reduces downtime. Safety and low maintenance for workshop resilience A dedicated safety locking mechanism secures the clamped position and prevents accidental release during handling or vibration-prone operations, improving operator confidence and process safety. The galvanised surface reduces corrosion-related wear, so maintenance intervals are longer and replacement cycles are extended. The overall design focuses on utilitarian robustness rather than unnecessary complexity, delivering consistent performance with minimal servicing—an advantage for shops that prioritise reliable tooling and predictable costs over time. For dependable clamping in assembly and fixture applications, select the Kukamet vertical toggle clamp 211 and contact Metav Werkzeuge for specification support and reliable supply from Emmerich. Technical data Article number (SKU): 211-1-D-L-C3 GTIN: 8680731509977 Eclass: 21041717 ETIM: EC011973 Core technical data Arm length: 144 mm Holding force: 1,000 N Clamping force (max): 750 N Weight: 0.155 kg Materials and features Material: galvanised steel Mounting: horizontal base Massive holding arm Safety locking mechanism FAQ What is the maximum holding capacity of this clamp? The Kukamet vertical toggle clamp 211 provides a holding capacity of up to 1,000 N and a maximum clamping force of 750 N. Can the clamp be mounted on standard fixture plates? Yes, the clamp is designed for mounting on a horizontal base and suits common fixture plates used in assembly and jigging. What material is the clamp made from? The clamp is manufactured from galvanised steel to increase corrosion resistance and durability in workshop conditions. Is the locking mechanism mechanical or hydraulic? The unit features a mechanical safety locking mechanism that secures the clamped position without external power. How heavy is the clamp and is it suitable for compact fixtures? With a weight of 0.155 kg and a 144 mm arm, the clamp is lightweight and intended for compact fixture arrangements. Manufacturer: Kukamet Fevzi Çakmak Mah.10644 Sk. No:61-63 42050 Karatay / KONYA TÜRKİYE / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com
144mm Vertical Clamp 750N Closing Force, Heavy-Duty Arm With Safety Lock, Zinc Plated - Kukamet
Secure, compact and corrosion-resistant: the galvanised vertical clamp combines a massive holding arm, a safety locking mechanism and a 144 mm reach to deliver reliable workholding with up to 1,000 N holding force and 750 N pressing capability. Order directly via Metav Werkzeuge or consult their specialists for specification support. Vertical clamp 212 — Galvanised vertical toggle clamp with 750 N press force (Kukamet) Vertical clamp 212 offers compact vertical clamping for workshop fixtures and metalworking jigs, designed to secure components where a vertical foot mounting is required. Galvanised steel construction Massive holding arm with safety lock Vertical foot mounting 750 N clamping force Compact 144 mm arm length Secure clamping for continuous production The vertical clamp is engineered for dependable workholding in repetitive processes. With a maximum press force of 750 N and a holding capacity of 1,000 N, the device reduces slippage and part movement during machining, assembly or inspection operations. The galvanised finish provides corrosion resistance, lowering the risk of surface degradation in humid or workshop environments. This combination of measurable clamping figures and durable coating supports consistent cycle times and fewer rejected parts, a clear benefit for production planning and cost-efficiency. Robust engineering that withstands daily use Built around a massive holding arm and fitted with a safety locking mechanism, the clamp prioritises mechanical reliability and operator safety. The robust construction minimises deformation under load and maintains clamping repeatability over prolonged use. At a weight of just 0.125 kg, the component contributes minimal additional mass to fixture assemblies while remaining sturdy. These design choices translate into lower maintenance needs and longer service intervals, making the clamp a practical option for workshops seeking durable, low-hassle tools. Compact footprint for flexible fixture design The vertical foot configuration enables direct mounting to machine beds, jigs or fixture plates without complex adapters. The 144 mm arm length gives a balanced reach for medium-sized workpieces while keeping the overall footprint compact. This allows tighter nesting of clamps in multi-point fixturing and simplifies layout planning. The toggle-style action delivers rapid clamping and release, supporting faster setup changes and contributing to reduced non-productive time in small and large batch scenarios alike. Practical applications and trustworthy sourcing Suitable for standard workshop and metalworking applications, the clamp integrates into fixtures for drilling, light milling, assembly and inspection tasks. The product is available as SKU 212-1-D-L-C3, enabling precise identification in procurement and inventory systems. Sourcing via Metav adds the advantage of a European quality filter and a broad spare-part supply chain, supporting reliable resupply and consistent quality across batches. Contact Metav Werkzeuge for tailored advice on integrating the Kukamet vertical clamp into production fixtures — Metav’s specialists in Emmerich will assist with ordering and specification: info@metav-werkzeuge.com | +49 2822 7131930 Technical data Article number: 212-1-D-L-C3 GTIN: 8682843520307 Facts Weight: 0.125 kg Arm length: 144 mm Maximum press force: 750 N Maximum holding force: 1,000 N Special features Material: Galvanised Mounting: Vertical foot Massive holding arm Safety locking mechanism FAQ What is the maximum clamping capacity of this clamp? The Kukamet vertical clamp 212 provides a maximum holding force of 1,000 N and a press force of 750 N. How is the clamp mounted in a fixture? Mounting is by a vertical foot, designed for direct attachment to machine beds, jig plates or fixture bases. What material and surface treatment does the clamp have? The unit is made of galvanised material, offering corrosion resistance suitable for workshop environments. What is the arm length and overall weight? The clamp features a 144 mm arm and weighs 0.125 kg, enabling compact fixture layouts. Does the clamp include any safety features? Yes, the device is fitted with a safety locking mechanism and a massive holding arm to maintain engagement under load. Manufacturer: Kukamet Fevzi Çakmak Mah.10644 Sk. No:61-63 42050 Karatay / KONYA TÜRKİYE / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com
144mm Vertical Clamp 750N Closing Force, Massive Holding Arm With Safety Lock, Blackened Finish - Kukamet
Take advantage of a massive holding arm, a secure safety lock and a compact 144 mm lever for reliable fixture work; the combination of robust design and measurable clamping performance ensures consistent results in production and jigs. Order the clamp directly via Metav Werkzeuge or consult our specialists for application advice. Kukamet Vertical toggle clamp 212 — 144 mm lever, safety locking Kukamet Vertical toggle clamp 212 is a vertical clamping device designed for fixed fixtures and repeatable holding tasks in workshop and production environments. Massive holding arm and safety lock Holding force up to 1,000 N Clamping force 750 N 144 mm lever arm for leverage Blackened finish for corrosion resistance Accurate clamping for repeatable fixtures The clamp delivers defined holding and clamping values that make process setup measurable and reproducible. With a holding force of 1,000 N and a clamping force of 750 N, the device secures workpieces reliably during machining, assembly or inspection. The numeric forces permit straightforward comparison with fixture requirements and support decision-making for jigs and production layouts. Using a lever-style mechanism ensures rapid actuation and a consistent clamping stroke, reducing setup time and variability between cycles. Durable construction with a safety interlock Built around a massive holding arm, the clamp combines mechanical strength with a safety lock that prevents unintended release under load. The blackened finish offers increased surface durability and a professional appearance while helping to resist corrosion in workshop conditions. The 144 mm lever provides a favourable mechanical advantage for secure engagement with moderate operator effort. These design choices extend service life and reduce the need for frequent replacements, supporting a stable production rhythm. Compact, lightweight and easy to integrate The clamp’s compact footprint and vertical foot mounting allow straightforward installation on fixtures, plates or tooling boards. At approximately 125 g, the unit is light enough to fit into modular jig systems without significantly increasing mass, while still delivering industrial clamping performance. The straightforward mechanical design facilitates maintenance and inspection; components are readily accessible for routine checks. For customers aiming to consolidate suppliers, this clamp represents a dependable element that integrates into a broader tooling strategy supplied from a central European stock. For reliable clamping with a massive holding arm and safety lock, contact Metav Werkzeuge for technical advice or to request stock availability from our Emmerich warehouse Technical data Article number: B212-1-D-L-C3 SKU: B212-1-D-L-C3 Category: Spanner Manufacturer: Kukamet eClass: 21041717 ETIM: EC011973 Facts Lever arm: 144 mm Clamping force max: 750 N Holding force max: 1,000 N Weight: 0.125 kg Special features Massive holding arm Safety locking mechanism Blackened finish Vertical foot mounting Compact lever-style toggle FAQ What is the maximum holding force of the Kukamet vertical toggle clamp 212? The Kukamet vertical toggle clamp 212 provides a holding force of up to 1,000 N, specified for fixture stability under load. Can this clamp be mounted vertically on a tooling plate? Yes. The clamp features a vertical foot mounting intended for direct attachment to plates and fixture bases. Is the lever length suitable for use with manual jigs? The 144 mm lever arm offers a good mechanical advantage for hand-operated jigs while remaining compact for close-packed tooling. What finish does the clamp have and how does it affect durability? The unit is supplied with a blackened finish which improves surface resistance and helps to protect against workshop corrosion. Which applications are typical for this type of toggle clamp? This clamp is suited to repeatable holding tasks in assembly, welding jigs, inspection fixtures and light machining where defined clamping and holding forces are required. Manufacturer: Kukamet Fevzi Çakmak Mah.10644 Sk. No:61-63 42050 Karatay / KONYA TÜRKİYE / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com
144mm Vertical Clamp 750N Thrust, Massive Holding Arm, Blackened Finish - Kukamet
Take advantage of the robust holding arm, compact 144 mm reach and dependable holding capacity to secure repetitive clamping tasks with minimal setup time; order the vertical clamp directly via Metav Werkzeuge or consult our advisors for application support. Vertical clamp 211 (B211-1-D-C3) – horizontal-foot lever clamp, 144 mm arm, Kukamet A Vertical clamp 211 engineered for secure vertical clamping in workshop fixtures, offering a compact reach and a horizontal foot for stable bench mounting. Robust holding arm, 144 mm reach Horizontal foot mount for bench fitting Clamping force 750 N Holding force 1,000 N Consistent clamping power for repeatable results The 211 delivers precise, measurable performance through a defined 750 N clamping force and a higher 1,000 N holding force, making it suitable where repeatable restraint is essential. The distinction between clamping and holding force is practical: the clamping force describes the active pressure applied when engaging the lever, while the holding force indicates the maximum static retention the device can maintain once closed. For production jigs and small-batch fixtures this clarity in specification reduces setup iterations and improves cycle-time predictability. The compact actuator and lever mechanism ensure rapid operation without complex adjustment, supporting efficient process flow. Space-saving design that fits into standard fixtures With a 144 mm reach and a low installed weight, the clamp integrates easily into constrained layouts and jig plates. The horizontal foot mount enables straightforward bench or plate attachment by bolting the base, keeping alignment simple during assembly. The combination of a compact arm and a durable finish produces a fixture component that is unobtrusive yet robust, allowing more freedom in positioning adjacent tooling. The lightweight construction contributes to easier handling during fixture building while the solid arm geometry maintains lateral stability under load. Durable finish and a rugged holding arm for production use A massive holding arm and black burnished finish provide a solid tactile feel and long-lasting appearance in workshop environments. The lever-style mechanism is engineered for frequent actuation, offering dependable performance for clamping cycles common in assembly, welding tack-up, or inspection stations. Maintenance is straightforward: the simple mechanical design allows quick visual checks of wear and immediate replacement if required, limiting downtime. For manufacturing contexts that prioritise reliability and straightforward integration, this clamp supplies a practical balance of endurance and ease of use. For procurement or technical advice on the Kukamet vertical clamp 211 (SKU B211-1-D-C3), contact Metav Werkzeuge in Emmerich at info@metav-werkzeuge.com or call +49 2822 7131930 to confirm suitability for specific fixtures and processes. Technical data SKU: B211-1-D-C3 GTIN: 8680731507638 eClass: 21041717 ETIM: EC011973 Facts Arm length: 144 mm Clamping force: 750 N Holding force: 1,000 N Weight: 0.16 kg Special features Horizontal foot mount Massive holding arm Black burnished finish Category: Lever clamp FAQ What clamping and holding forces does this clamp provide? The clamp provides a clamping force of 750 N and a holding force of 1,000 N as specified for the Vertical clamp 211 (Kukamet, SKU B211-1-D-C3), suitable for many bench fixture tasks. How is the clamp mounted to a fixture or bench? Mounting is via the horizontal foot, allowing the clamp to be bolted to plates or benches for secure attachment and easy alignment. Is the arm length suitable for compact jig designs? Yes, the 144 mm arm reach is intended for compact fixtures where space is limited while still offering practical leverage and accessibility. What finish and construction can be expected for workshop durability? The device features a black burnished finish and a massive holding arm, designed to withstand frequent operation and maintain a consistent appearance. Can this clamp be used for repetitive production cycles? The lever-style mechanism and robust arm design make the model appropriate for repetitive clamping cycles in assembly and inspection setups. Manufacturer: Kukamet Fevzi Çakmak Mah.10644 Sk. No:61-63 42050 Karatay / KONYA TÜRKİYE / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com
144mm Vertical Clamp Massive Holding Arm, 750N Thrust/1000N Clamp - Kukamet
Take advantage of the combination of robust galvanised construction, a 144 mm reach and reliable holding capacity up to 1,000 N for accurate, repeatable clamping in production and assembly. Order the clamp directly via Metav Werkzeuge or request technical advice from our consultants. Vertical clamp 212 – Vertical toggle clamp with galvanised finish and 144 mm arm (Kukamet) The Vertical clamp 212 is a mechanically robust vertical toggle clamp designed for jigs, fixtures and general workshop holding tasks where secure, repeatable clamping is required Solid galvanised construction for corrosion resistance Massive holding arm for long service life 1,000 N maximum holding force Vertical foot for secure fixture mounting Secure clamping for repeatable production The clamp delivers dependable hold with a 1,000 N holding force and a separate 750 N clamping force, making it suitable for production settings where repeatability matters. The toggle mechanism locks positively, so the workpiece remains immobile while machining, welding or assembly takes place. For non‑specialists: the difference between holding and clamping force reflects how tightly the device keeps a part in place (holding) versus the immediate clamping action (clamping), which together ensure process stability and reduced rework. Durable construction that tolerates workshop conditions Manufactured in a galvanised finish, the design resists surface corrosion and keeps moving parts protected on busy shop floors. The massive holding arm increases fatigue resistance and reduces deformation under load, extending service intervals and lowering lifetime costs. The compact 144 mm arm length balances reach with rigidity, allowing secure positioning without excessive leverage that could compromise the fixture or the clamp itself. Quick integration into jigs and fixtures The vertical mounting with a vertical foot allows straightforward installation into benches, welding tables or custom fixtures. The compact footprint and standard mounting layout support rapid retrofitting into existing setups, while the toggle action enables fast manual operation during assembly cycles. Where automation is involved, the simple mechanical interface makes it easy to design a fixture that achieves consistent clamping stroke and repeatable positioning. Practical benefits for workshop and production use Beyond raw figures, the clamp emphasises reliability and low maintenance: galvanised surfaces need less upkeep, the robust arm reduces frequent replacements, and the positive locking mechanism improves operator confidence. The combination of features supports higher throughput and fewer quality checks, which is particularly valuable when fixtures are used for small series or repeatable batch production. Contact Metav Werkzeuge for specification support and secure the Kukamet Vertical clamp 212 for resilient, repeatable clamping in your fixtures — technical consultants are available to advise on integration and ordering. Technical Data SKU: 212-1-D-C3 GTIN: 8680731505658 ETIM: EC011973 ECLASS: 21041717 Manufacturer brand: Kukamet Facts Arm length: 144 mm Weight: 0.184 kg Maximum holding force: 1,000 N Maximum clamping force: 750 N Special features Material: galvanised Massive holding arm Vertical foot mounting Category: clamp / toggle clamp FAQ What applications suit this vertical toggle clamp? The vertical clamp 212 is suited to jigs, fixtures, welding tables and assembly stations where a compact, positive‑locking hold is required; its 1,000 N holding force supports typical workshop tasks. How is the clamp mounted? Mounting is via the vertical foot arrangement; the Kukamet Vertical clamp 212 is designed for secure attachment to benches or fixture plates using standard fasteners. Is the finish resistant to corrosion? Yes, the galvanised finish on the vertical clamp 212 provides enhanced surface corrosion resistance for workshop and light industrial environments. What maintenance is required? Routine inspection and light lubrication of pivot points will extend service life; the massive holding arm and galvanised surfaces reduce the need for frequent replacement. Can this clamp be used for welding fixtures? Yes, the positive toggle lock and robust construction make the clamp suitable for welding fixtures where repeatable positioning and secure holding are necessary. Manufacturer: Kukamet Fevzi Çakmak Mah.10644 Sk. No:61-63 42050 Karatay / KONYA TÜRKİYE / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com
144mm Vertical Clamp With Massive Holding Arm And Safety Lock, Wafer Mount - Kukamet
Take advantage of the dependable combination of a massive holding arm, safety lock, and a horizontal-foot mounting that together ensure consistent clamping performance and fast fixture setup; order the clamp directly via Metav Werkzeuge or consult our specialists for application guidance. Kukamet Vertical Toggle Clamp 211 — heavy-duty arm, horizontal base Kukamet Vertical Toggle Clamp 211 is a compact toggle clamp designed for secure vertical clamping in jigs, fixtures and production tooling. Heavy-duty holding arm with safety lock Horizontal foot for stable mounting Holding force up to 1,000 N Compact weight 155 g Reliable clamping performance for production use The clamp delivers measurable performance: a holding force of 1,000 N and a clamping force of 750 N, values that translate into secure workpiece retention during machining and assembly operations. The 144 mm arm provides an extended lever for consistent force transmission while the reinforced construction reduces deformation under load. These numerical specifications allow planners and engineers to calculate safety factors and fixture layouts with confidence, supporting optimised process stability and lower rework rates. Design features that increase safety and uptime Equipped with a safety lock and a massive holding arm, the device ensures that a workpiece remains clamped even under vibration or incidental contact. The toggle mechanism locks positively at full travel, preventing accidental release during handling. Such mechanical safety reduces downtime caused by part shift and minimises the need for secondary checks, which benefits production throughput and operator peace of mind. Quick installation and flexible application A horizontal foot mounting simplifies integration into existing plates and tooling boards; the clamp can be bolted to flat surfaces for immediate use. The compact form factor and lightweight 155 g body make it suitable for both permanent fixtures and removable clamping aids. Typical applications include small-batch fixtures, inspection jigs, assembly stations and light machining tasks where predictable clamping force and rapid operation are priorities. Hard-wearing finish and maintenance advantages Finished in a blackened finish that provides basic corrosion resistance and a professional appearance, the clamp requires minimal maintenance. Routine lubrication of the pivot points and periodic inspection of the lock mechanism are sufficient to maintain consistent performance. The straightforward mechanical design facilitates quick replacement or retrofit within modular tooling systems, helping to keep total cost of ownership low. Secure reliable clamping for production — contact Metav Werkzeuge for stock availability and technical advice on the Kukamet Vertical Toggle Clamp 211 (SKU B211-1-D-L-C3). Technical Data Article number: B211-1-D-L-C3 ETIM: EC011973 eClass: 21041717 Facts Arm length: 144 mm Holding force max: 1,000 N Clamping force max: 750 N Weight: 0.155 kg Special features Blackened finish Massive holding arm Safety lock Horizontal foot mounting Category: Toggle clamp FAQ What holding and clamping forces are specified for the clamp? The Kukamet Vertical Toggle Clamp 211 specifies a holding force of 1,000 N and a clamping force of 750 N, suitable for light to medium-duty fixtures. Which mounting option is provided for installation? The clamp features a horizontal foot for secure bolted mounting to plates and tooling boards. What is the arm length and how does it affect clamping? An arm length of 144 mm offers extended lever action, improving force transmission and allowing easier engagement of the clamping action. What surface finish does the clamp have and how should it be maintained? The device is supplied with a blackened finish; simple periodic lubrication of pivots and inspection of the lock are recommended for long service life. Is the clamp suitable for portable jigs and removable fixtures? Yes, the compact design and lightweight construction make it appropriate for removable and modular fixturing applications. Manufacturer: Kukamet Fevzi Çakmak Mah.10644 Sk. No:61-63 42050 Karatay / KONYA TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
144mm Vertical Clamp With Massive Holding Arm, 750N Thrust / 1000N Hold - Kukamet
Take advantage of the galvanised construction, the massive holding arm and predictable force ratings to achieve reliable fixture clamping in light- to medium-duty production. Order the vertical clamp directly via Metav Werkzeuge or consult the team for application advice. Vertical Toggle Clamp 211 — Kukamet, 144 mm arm, galvanised The Vertical Toggle Clamp 211 is a compact vertical clamping device for workshop fixtures and jigs, designed for secure holding with a horizontal-foot mounting and a robust holding arm. Massive holding arm for stable clamping 144 mm arm length for extended reach Galvanised steel for corrosion resistance 1,000 N maximum holding force Consistent holding force for repeatable production results The clamp delivers a maximum holding force of 1,000 N and a clamping (pressing) force of 750 N, values that support repeatable fixation of workpieces in assembly and machining jigs. These measurable force ratings enable planners to calculate fixture safety margins and cycle behaviour accurately. The toggle mechanism converts a compact lever movement into a secure lock, reducing vibration-related loosening and helping to maintain process stability. Robust, corrosion-resistant build for workshop environments Constructed from galvanised steel, the unit resists surface corrosion in everyday shop conditions, extending service life where occasional coolant mist or humidity occurs. The massive holding arm adds rigidity to the load path, reducing deflection under clamping loads and improving positional stability of the workpiece. Lightweight yet durable, the component fits into mixed-material workstations without adding unnecessary bulk to the fixture. Easy integration into existing fixtures and jigs With a horizontal-foot mounting the clamp mounts directly to flat plates or fixture bases, simplifying retrofit and new-build installations. The 144 mm arm length provides extended reach for offset workpieces while retaining a low profile when locked. The compact form and predictable geometry allow CAD planning teams to model clamping clearance precisely, shortening the time from design to functional prototype. Practical specification for procurement and maintenance The unit weighs approximately 0.16 kg, which minimises added mass in moving assemblies and makes bulk handling straightforward during fixture assembly. The simple lever design reduces the number of wear parts, which keeps maintenance intervals predictable and spare-part lists short. Traceable identifiers such as the SKU and GTIN support inventory control and reordering processes in production supply chains. For robust, corrosion-resistant clamping choose Kukamet’s Vertical Toggle Clamp 211 — contact Metav Werkzeuge for technical advice and local availability: info@metav-werkzeuge.com or +49 2822 7131930 Technical Data Article number: 211-1-D-C3 GTIN: 8680731505818 EClass: 21041717 ETIM: EC011973 Core technical data Arm length: 144 mm Maximum holding force: 1,000 N Maximum clamping force: 750 N Weight: 0.16 kg Materials & features Material: galvanised steel Mounting: horizontal foot Massive holding arm Version: vertical toggle clamp (model 211) FAQ What holding and clamping forces does the clamp provide? The Vertical Toggle Clamp 211 offers a maximum holding force of 1,000 N and a clamping (pressing) force of 750 N, specified for reliable fixture fixation. How is the clamp mounted to a fixture base? The clamp is designed for horizontal-foot mounting, allowing direct attachment to flat plates or fixture bases in jigs and workholding frames. Which material is the clamp made from and how does that affect durability? Made from galvanised steel, the clamp resists surface corrosion in standard workshop conditions and offers extended service life compared with untreated components. What is the arm length and how does it influence application? The arm measures 144 mm, providing additional reach for offset workpieces while maintaining a compact locked profile suitable for tight fixture layouts. Is the clamp suitable for use in production jigs and assembly fixtures? Yes; the model’s predictable force ratings, robust arm and toggle mechanism make it appropriate for light- to medium-duty production jigs and assembly fixtures where repeatable clamping is required. Manufacturer: Kukamet Fevzi Çakmak Mah.10644 Sk. No:61-63 42050 Karatay / KONYA TÜRKİYE / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com
144mm Vertical Clamp With Massive Holding Arm, 750N Thrust / 1000N Hold - Kukamet
Compact, reliable clamping performance with a solid 144 mm holding arm and up to 1,000 N holding force ensures secure workpiece retention in light-duty fixtures; combine robustness and low weight for fast setups and consistent repeatability. Order the unit directly via Metav Werkzeuge or contact the consultants for application advice. Kukamet Vertikalspanner 212 — vertical toggle clamp with 1,000 N holding force A 212 vertical clamp designed for secure vertical clamping in jigs and fixtures where compact size and repeatable force are essential Solid 144 mm holding arm Up to 1,000 N holding force Vertical foot mounting Robust clamping where repeatability matters The clamp delivers a consistent holding force of up to 1,000 N, supported by a maximum pressing force of 750 N, which together provide reliable retention during assembly, welding and light machining operations. The difference between holding and pressing force is explained by the clamp geometry: the holding value indicates the sustained retention capacity when engaged, while the pressing value refers to the direct clamping pressure applied. The solid holding arm and the compact construction reduce elastic deformation and improve repeatability, lowering setup time and minimising rework in repetitive production. Easy integration for compact fixtures A low mass of 0.184 kg and a vertical foot mounting allow the clamp to be fitted into confined spaces without adding significant inertia to moving assemblies. The 144 mm arm provides sufficient reach for many small to medium-sized fixtures while keeping the profile compact. Integration is simplified by the toggle-style mechanism that secures workpieces quickly and releases smoothly, which supports faster cycle times and more efficient jig design in batch production or prototype setups. Durable finish and maintenance-friendly design The component’s blackened finish offers basic surface protection and provides a professional appearance for workshop environments. The solid arm construction is designed for long service life under regular use; routine inspection and lubrication of pivot points keep the mechanism operating reliably. The compact design and robust materials mean fewer replacement components and predictable service intervals, contributing to lower total cost of ownership over time. Practical technical advantages for the workshop This clamp’s geometry and rated forces make it suitable for light-duty holding tasks where repeatability and space savings are priorities. The toggle action converts small operator movement into high clamping force, enabling quick manual operation or straightforward integration into automated handling systems. Built with workshop efficiency in mind, the clamp reduces handling time and helps maintain consistent quality across repetitive tasks. For dependable, compact vertical clamping choose the Kukamet 212 and contact Metav Werkzeuge for tailored advice and prompt supply from Emmerich Technical data SKU: B212-1-D-C3 GTIN: 8680731507843 ECLASS: 21041717 ETIM: EC011973 Core specifications Weight: 0.184 kg Arm length: 144 mm Holding force (max): 1,000 N Pressing force (max): 750 N Features & finish Material/finish: blackened Mounting: vertical foot Feature: solid holding arm Category: toggle clamp / spanner Storytrigger: lever clamp FAQ What is the difference between the holding and pressing force? The holding force (1,000 N) is the clamp’s retention capacity once engaged; the pressing force (750 N) refers to the direct clamping pressure applied by the mechanism. Can the clamp be used in automated fixtures? Yes, the toggle-style action and compact profile allow integration into automated or semi-automated jigs, provided actuation and fixture geometry are adapted to the clamp’s mounting and arm length. What material and finish does the clamp have? The clamp is supplied with a blackened finish, offering basic surface protection and a durable appearance for workshop use. Is the clamp suitable for heavy machining applications? The clamp is intended for light to medium-duty holding tasks; for heavy machining applications, a higher-capacity clamp designed for those loads is recommended. What is the SKU for ordering or referencing? The SKU is B212-1-D-C3 and the GTIN is 8680731507843, useful for procurement and spare-part reference. Manufacturer: Kukamet Fevzi Çakmak Mah.10644 Sk. No:61-63 42050 Karatay / KONYA TÜRKİYE / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
145mm Precision Machine Vice Modular Hydraulic Option, 0.01mm Accuracy, 2000 kgf Clamping Force - Vertex
Robust modular vice combining 2000 kgf clamping force with a 0–200 mm opening and guaranteed 0.01 mm accuracy — order directly via Metav Werkzeuge or ask our consultants for configuration advice VMP-7A Precision machine vice (Vertex) — 2000 kgf clamping force, 0–200 mm opening The VMP-7A is a precision machine vice intended for modular workholding in milling and machining environments, available with an optional hydraulic configuration for increased productivity Precision 0.01 mm accuracy 2000 kgf clamping force 0–200 mm adjustable opening Modular design, optional hydraulic Consistent heavy-duty clamping for repeatable results The vice delivers a measurable advantage where secure holding and repeatability matter most. With a clamping force of 2000 kgf and construction from alloy steel, the unit provides a stable workholding platform that reduces part movement and supports tight tolerances. The 0.01 mm accuracy specification reflects controlled manufacture and finishing processes; this level of precision reduces setup iterations and lowers scrap rates in serial production. For workshops seeking predictable outcomes, the robust clamping performance directly translates into fewer interruptions and more consistent machining cycles. Flexible modularity to match production needs Modularity is at the core of the design: the vice can be configured as a purely mechanical device or adapted with a hydraulic option to suit higher-throughput operations. The adjustable 0–200 mm opening covers a wide range of workpiece sizes, allowing a single fixture to replace multiple dedicated jigs. Modular elements simplify retrofitting and changeovers, so integration into existing machining centres is straightforward. The option to add hydraulic actuation supports faster cycle times where automatic clamping and unclamping contribute to overall productivity gains. Precision that supports quality assurance and measurement Accurate clamping reduces variation at the workpiece and eases downstream inspection. The vice’s 0.01 mm positional reliability helps maintain nominal dimensions through machining, which simplifies quality control and shortens measurement loops. Where measurement equipment and inspection processes are employed, stable fixturing limits the influence of fixture-induced errors, enabling clearer comparison between part data and design tolerances. This vice therefore acts as a practical tool for achieving reproducible quality rather than a variable source of error. Durable construction and compact footprint for workshop use Built from alloy steel and weighing 43.7 kg, the unit balances mass for vibration damping with a compact footprint of 145 x 455 x 118 mm, making it suitable for many machine tables without excessive overhang. The solid build avoids deformation under load and supports reliable clamping cycles over prolonged use. Modular configuration and standardised interfaces facilitate maintenance and spare-part management, while the vice’s dimensions and mass contribute to stable machining performance without occupying unnecessary table space. Discuss hydraulic conversion and workshop integration with Metav Werkzeuge to select the optimal VMP-7A configuration; contact info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: VMP-7A GTIN: 4061905089602 ETIM: EC002173 eCl@ss: 21020601 Facts Weight: 43.7 kg Dimensions: 145 x 455 x 118 mm Opening: 0–200 mm Clamping force: 2000 kgf Accuracy: 0.01 mm Special features Material: alloy steel Type: mechanical Modular design with optional hydraulic configuration Suitable for heavy-duty machining workholding FAQ What is the maximum jaw opening of the vice? The vice offers an adjustable opening of 0–200 mm, suitable for a wide range of workpiece sizes and adaptable clamping setups. Is a hydraulic version available? Yes — the VMP-7A features a modular design that can be supplied with an optional hydraulic configuration for automated clamping cycles. What level of accuracy can be expected during use? Manufactured to an accuracy of 0.01 mm, the VMP-7A supports tight tolerances and repeatable positioning for precision machining tasks. What materials make up the vice and how does that affect performance? The vice is constructed from alloy steel, providing stiffness and wear resistance that contribute to stable clamping and reduced deformation under load. What are the physical dimensions and weight for machine table planning? Dimensions are 145 x 455 x 118 mm and the unit weight is 43.7 kg, allowing for straightforward assessment of table load and fixture layout. Manufacturer: Vertex Machinery Works Co., Ltd.; No. 296, Sec. 1, Feng Shih Road, Fengyuan District, Taichung City 420, Taiwan
145mm Universal Jaws With Stop, 0.01mm Resolution, Soft Stop For Irregular Parts - Vertex
Take advantage of the combination of soft stop for irregular pieces and a 100–110 mm jaw width to ensure reliable, repeatable clamping with 0.01 mm precision; order the universal jaws directly via Metav Werkzeuge or consult their advisors for fitment guidance and rapid dispatch. Vertex Universal Jaws with Stop — 100–110 mm jaw width, 0.01 mm precision The Vertex Universal Jaws with Stop provide adaptable clamping and precise measurement support for workshop and inspection applications. Soft stop for irregular pieces Jaw width 100–110 mm compatibility Precision to 0.01 mm Designed for metrology and clamping Precision clamping that supports reliable measurement results The core advantage of these jaws is their measured precision. With a specified 0.01 mm level of accuracy, the design focuses on reducing variation at the clamping interface and enabling repeatable positioning for inspection and setup tasks. The compact dimensions (145 x 38 x 49 mm) concentrate clamping forces where they are needed while maintaining a small footprint, which supports tight fixture layouts in busy inspection benches. For technical teams, this translates into fewer re-measurements and tighter process control, especially where small deviations can affect downstream quality. Versatile compatibility and protection for irregular components Compatibility with a jaw width 100–110 mm means the jaws suit measuring fixtures and clamping setups that accept that span. The integrated soft stop cushions contact with non-uniform or delicate parts, limiting point loading and surface damage while maintaining secure hold. Technically, the soft stop absorbs irregularities in form without compromising clamping stability, so components with uneven faces or slight distortions can be checked or machined without additional fixturing. This versatility reduces the need for custom jaw inserts in many routine tasks. Practical benefits for workshop efficiency and inspection throughput These jaws combine straightforward function with tangible efficiency gains: reduced handling time, fewer auxiliary tools and a lower risk of damage to samples during clamping. The modest overall size aids in quick set-up and repositioning on test benches or fixtures. As a component intended for clamping and metrology use, it supports streamlined workflows by integrating easily into existing stations and helping to maintain consistent measurement conditions across batches. Supplier assurance and fitment support from Metav Selection of measurement and clamping accessories is often a small decision with large consequences; confidence in supply and compatibility matters. Supplied through Metav Werkzeuge, the product benefits from a European quality filter and distribution hub in Emmerich that aims to ensure consistent stock and clear technical information. For teams planning integration into inspection or production cells, the combination of Vertex engineering and Metav’s distribution reduces uncertainty about availability and specification matching. For tailored advice on integration or to confirm suitability for a specific measuring instrument, contact Metav Werkzeuge in Emmerich by email at info@metav-werkzeuge.com or by phone at +49 2822 7131930 — their advisors will assist with compatibility checks and dispatch options. Technical Data Article number: VWSJ-R100 GTIN: 4061905083914 ECLASS: 21029107 Dimensions: 145 x 38 x 49 mm Core figures Accuracy: 0.01 mm Jaw width compatibility: 100–110 mm Special features Soft stop for irregular pieces With stop (mit Anschlag) Designed for clamping and metrology applications FAQ Are these jaws compatible with calipers and measuring fixtures? These universal jaws are compatible with fixtures and calipers that accept a jaw width of 100–110 mm; the VWSJ-R100 designation identifies the set and its intended span. What does the soft stop do and when should it be used? The soft stop cushions contact against uneven or delicate parts, reducing surface marking and accommodating small form deviations while retaining clamping stability for inspection or handling. What accuracy can be expected when using these jaws for measurement tasks? A declared accuracy of 0.01 mm supports precise positioning for repeatable measurement; overall system accuracy will also depend on the measuring instrument and fixturing. Can irregularly shaped workpieces be secured reliably with these jaws? Yes—due to the soft stop, the jaws are suited to irregular components where rigid metal-to-metal contact would risk deformation or slippage; final suitability depends on the specific part geometry. Who manufactures the product and where is it produced? The product is manufactured by Vertex; the VWSJ-R100 is part of Vertex’s range of clamping accessories designed for metrology and workshop use. Manufacturer: Vertex Machinery Works Co., Ltd.; No. 296, Sec. 1, Feng Shih Road, Fengyuan District, Taichung City 420, Taiwan
147mm Morse Taper MT3 Taper Shank With B22 Drill Chuck Mount, Hardened And Ground - TECWERK
Benefit from the secure fit of an MT3 taper combined with the B22 drill‑chuck interface and the durability of a fully hardened and ground finish; this combination reduces runout and supports consistent tool performance. Improve machine uptime and minimise rework by specifying the DIN‑conforming arbor. Order the taper arbor directly via Metav Werkzeuge or request technical advice from our consultants. Taper arbor MT3×B22 (TECWERK) — DIN 238, hardened and ground, 147 mm Taper arbor MT3×B22 for accepting drill chucks; designed for drill and turning machines with a DIN 238 drill‑chuck interface DIN 238 drill‑chuck taper B22 Morse taper MT3 external shank Fully hardened and precision ground Suitable for drill and turning machines Proven precision for reduced runout and consistent results A defined taper fit is the basis for rotational accuracy in machining. The MT3 external taper paired with the B22 drill‑chuck interface manufactured to DIN 238 provides a standardised seating that minimises micro‑movement. The hardened and ground finish lowers friction and limits elastic deformation during clamping, which in turn reduces runout and improves repeatability. These characteristics translate into fewer rejected parts and more predictable machining outcomes, particularly important for repetitive drilling operations and fine finishing tasks. Durable design that lowers maintenance needs Workshop applications demand components that resist wear and retain concentricity under repeated use. The arbor’s fully hardened and precision ground execution increases abrasion resistance and helps maintain retention force over prolonged service. Reduced wear means longer intervals between checks and regrinding, supporting continuous production schedules. In practical terms, the robust surface treatment protects both the arbor and the mounted drill chuck, contributing to lower total cost of ownership in a busy tooling environment. Compact dimensions for straightforward machine integration The Taper arbor MT3×B22 has an overall length of 147 mm, a form factor that suits a wide range of drill presses and turning centres while keeping overhang and imbalance low. Supplied as a single unit (packaging unit: 1), the arbor accepts Jacobs‑style chucks with the B22 taper and simplifies inventory management. The product is listed under SKU 2000832337NW for straightforward ordering and specification checks. For machine matching and balance considerations, consult technical notes to ensure optimal mounting and safe operation. For precision toolholding with a DIN‑conforming drill‑chuck interface, request the TECWERK MT3→B22 taper arbor via Metav Werkzeuge; Metav’s Emmerich team can advise on fit, delivery and workshop integration at info@metav-werkzeuge.com or by phone on +49 2822 7131930 Technical data Article number: 2000832337NW Product: Taper arbor Brand: TECWERK Standard: DIN 238 Core dimensions Taper (external): MT3 Chuck taper: B22 (DIN 238) Overall length: 147 mm Packaging unit: 1 Design and features Fully hardened and ground For the acceptance of drill chucks on drill and turning machines Execution: hardened and ground Suitable for Jacobs‑type chucks FAQ Is the arbor compatible with standard MT3 spindles? Yes. The arbor features an MT3 external taper designed for standard MT3 spindles and mates with B22 drill‑chuck fittings according to DIN 238. What does compliance with DIN 238 mean for the user? DIN 238 specifies the dimensions and tolerances for drill‑chuck tapers; conformity ensures interchangeability and predictable seating when using any B22‑compatible chucks with this arbor. How does the hardened and ground finish affect performance? The hardened and ground surface improves wear resistance and maintains concentricity, so the arbor preserves retention and reduces runout over many clamp cycles. Which machines is this arbor suitable for? The component is intended for drill presses and turning machines that accept MT3 external tapers and B22 drill‑chuck fittings; it is commonly used where Jacobs‑type chucks are mounted. What is the overall length and how is it supplied? Overall length is 147 mm and the item is supplied as a single unit (packaging unit: 1), referenced under SKU 2000832337NW. Manufacturer/Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund
14mm 5C Collet High-Precision 0.02mm Runout, 87mm Length - Vertex
Take advantage of the high clamping precision and compact form factor to improve machining repeatability and reduce setup time. The combination of 0.02 mm runout tolerance, a 14 mm nominal bore and an 87 mm overall length supports consistent tool concentricity and deeper gripping in standard 5C systems. Order the collet directly via Metav Werkzeuge or consult the Metav team for compatibility advice. 5C-14 collet — 14 mm precision 5C clamping solution (Vertex) 5C-14 collet for secure tool and workpiece clamping in milling and turning operations Precision runout ≤ 0.02 mm Nominal bore 14 mm 87 mm length for deeper clamping Compatible with 5C collet chucks Consistent machining through predictable clamping A reliable clamp is the foundation of repeatable machining. The 5C clamping sleeve delivers a tight concentric hold with a documented 0.02 mm runout, which translates into reduced wobble and more accurate final dimensions. For workshop environments where tolerance stacks matter, this level of precision helps maintain part quality across runs and shortens rework cycles. The reduced radial runout also supports improved surface finish without altering cutting parameters. Longer reach with stable grip for versatile setups With an 87 mm overall length, the collet achieves deeper engagement for longer tools or workpieces, while its balanced design keeps forces evenly distributed. The combination of length and 14 mm bore ensures stable axial support in through-hole or extended-tool arrangements, reducing vibration that shortens tool life. Stability in the clamping interface results in fewer tool changes and steadier cycle times, directly supporting production efficiency goals. Seamless integration into existing 5C systems Designed for standard 5C equipment, the sleeve is compatible with common chucks and collet bodies used across metalworking shops. The familiar interface minimises retrofitting and simplifies inventory management, enabling centralised tool handling. Clear numeric specifications and standard form factor allow straightforward interchangeability, supporting lean workshop processes and faster set-ups without specialised adapters. Practical benefits for tool life and process reliability Accurate clamping reduces micro-movements that accelerate wear on cutting edges, making the device an investment in longer tool life and fewer downtime events. The modest mass of 0.21 kg contributes to a low rotating inertia when the collet is used close to the spindle nose, helping to maintain balance at operational speeds. With precise mechanical tolerance and consistent repeatability, the collet supports predictable throughput and a dependable manufacturing baseline. Contact Metav Werkzeuge today to confirm fitment and integrate the Vertex 5C-14 collet into the workshop stock from our Emmerich distribution centre Technical data Article number: 5C-14 GTIN: 4061905088391 Manufacturer: Vertex Facts Diameter: 14 mm Accuracy (runout): 0.02 mm Length: 87 mm Weight: 0.21 kg eClass: 21041712 Special features Collet type: 5C SKU: 5C-14 Brand: Vertex FAQ What tolerance can be expected from the 5C-14 collet? The 5C-14 collet delivers a typical runout accuracy of 0.02 mm, ensuring tight concentricity for precision machining. Is the collet compatible with standard 5C chucks? Yes, the sleeve is designed for compatibility with standard 5C collet chucks and bodies commonly used in milling and turning. For which applications is the 14 mm bore most suitable? The 14 mm nominal bore accommodates common tool shank sizes and small workpieces, offering stable clamping for general metalworking tasks. How does the 87 mm length affect clamping performance? An 87 mm overall length provides deeper engagement for longer tools or extended setups while maintaining even force distribution for reduced vibration. Manufacturer: Vertex Machinery Works Co., Ltd.; No. 296, Sec. 1, Feng Shih Road, Fengyuan District, Taichung City 420, Taiwan
14mm Automatic Centre Punch, 120mm Length - Vertex
The combination of an automatic impact mechanism, a 14 mm tip and a compact 120 mm form delivers consistent, defined centre marks while keeping handling light and precise. Order directly via Metav Werkzeuge or contact their consultants for specification advice and supply from the Emmerich quality hub. Automatic centre punch VACP-1 — 14 mm tip, 120 mm length (Vertex) The Automatic centre punch is a hand-held centre marker designed for precise, repeatable centre punching in metalworking and general workshop tasks. Automatic impact mechanism for repeatable marks 14 mm tip diameter for precise centre points 120 mm overall length for secure handling Lightweight at 0.07 kg for comfortable use Consistent centre marking for reliable drill starts A robust mechanical impact delivers precision without an external hammer, ensuring repeatability across successive marks. The spring-driven action produces a defined indentation that simplifies drill alignment and reduces wander at the start of a hole. For workshop environments where process reliability matters, this compact marker helps maintain consistent part quality and faster set-up times. The simple mechanical principle also makes the result easy to predict, which benefits repeat production runs and occasional one-off jobs alike. Designed for fast, ergonomic workshop operation With an overall length of 120 mm and a mass of only 0.07 kg, the tool balances positive control with low operator fatigue. The body length provides a comfortable grip while the automatic striking action removes the need for separate striking tools, speeding up marking tasks and reducing handling steps. This combination of compact design and automated impact delivers measurable time savings in marking workflows and contributes directly to improved throughput and operator comfort. Low-maintenance tool that integrates into workshop routines The straightforward mechanical construction minimises maintenance requirements and supports long service life under normal workshop use. Periodic cleaning and occasional lubrication of the mechanism are normally sufficient to keep performance stable. The 14 mm tip dimension provides a clearly defined contact area for consistent centre points. For confirmation on compatibility with specific materials or applications, Metav Werkzeuge can supply additional technical details and guidance by email or phone. Choose Vertex quality: contact Metav Werkzeuge for tailored advice and reliable supply from our Emmerich quality hub. Technical Data Article number: VACP-1 GTIN: 4061905083358 Manufacturer: Vertex Machinery Works Co., Ltd. Core specifications Diameter: 14 mm Length: 120 mm Weight: 0.07 kg eClass: 21022304 Special features Automatic centre punch mechanism Compact hand-held design SKU: VACP-1 Product type: Centre punch FAQ How does the automatic mechanism operate? The automatic mechanism in the Automatic centre punch uses a spring‑driven striker that creates an impact when pressed, producing a repeatable indentation without a hammer. What size of mark does the tip make? The tool is specified with a 14 mm tip diameter, which gives a clearly defined centre point suitable for drill starting and alignment tasks. Is the tool suitable for regular workshop use? Yes; the VACP-1 from Vertex is designed for routine workshop marking and benefits from a simple mechanical design that supports regular use with minimal maintenance. How should the centre punch be maintained? Keep the tool clean and free of swarf; occasional light lubrication of the mechanism is recommended to maintain smooth operation and consistent striking force. Can the centre marks be used as drill start points? The indentations produced by the VACP-1 provide reliable drill start points and help to prevent drill wandering when beginning a hole. Manufacturer: Vertex Machinery Works Co., Ltd.; No. 296, Sec. 1, Feng Shih Road, Fengyuan District, Taichung City 420, Taiwan
14mm Clamping Wedge Nr. 6314V Height 10-38mm M12x14x100mm - AMF
Compact clamping solution for 14 mm T-slots with an adjustable clamping height of 10–38 mm and supplied M12 x 14 x 100 mm clamping screw; combines straightforward installation and reliable workholding — order the AMF clamping jaw directly via Metav Werkzeuge or consult our specialists for application advice AMF clamping jaw Nr. 6314V — for 14 mm T-slot, adjustable clamping height 10–38 mm The AMF clamping jaw Nr. 6314V is a compact workholding component suited to T-slot fixtures, providing an adjustable clamping range for versatile workshop and production use Fits 14 mm T-slots Adjustable clamping height 10–38 mm Supplied with M12 x 14 x 100 clamping screw Robust design for industrial workholding Secure and adaptable workholding for T-slot fixtures The clamping jaw is engineered to deliver a secure grip in standard 14 mm T-slot systems, allowing straightforward accommodation of varying workpiece heights within the 10–38 mm range. This adjustability reduces the need for multiple shim sets or alternative jaws, streamlining setup procedures. The design translates into repeatable clamping pressure across batches, which supports consistent machining tolerances and fewer reworks. Compatibility with common T-slot profiles ensures quick integration into existing fixturing systems without major retrofitting. Fast installation and reduced setup time with included clamping screw Assembly is simplified by the delivered M12 x 14 x 100 mm clamping screw, which is matched to the jaw’s thread specification and overall length. The standard M12 thread provides reliable torque transmission for stable clamping, while the screw length suits common mounting depths in fixture plates. As a consequence, downtime for changeovers is minimised, and the component can be installed or replaced during routine maintenance with basic workshop tools. Clear mechanical interfaces reduce assembly errors and support predictable cycle times in production environments. Durable component design that supports industrial workflows Constructed for repetitive use in workshop and production settings, the jaw’s form factor focuses on long-term serviceability and consistent performance. The compact geometry is intended to withstand frequent clamping cycles and to fit within confined fixturing arrangements where space is at a premium. Attention to fit and thread standardisation reduces variability at the clamping interface, contributing to fewer rejects and a more reliable production flow. Metav’s sourcing and quality filter for the European market further ensures that each component meets industrial expectations for repeatability and robustness. Contact Metav Werkzeuge for availability of the AMF clamping jaw Nr. 6314V and for tailored advice on integrating this workholding component into existing fixture systems Technical data SKU: 4000833073NW Type: Nr. 6314V Brand: AMF Label: Spanneisen Nr.6314V f.T-Nut 14mm Spann-H.10-38mm Spannschraube M12x14x100mm AMF Packaging unit: 1 Facts T-slot width: 14 mm Width: 14 mm Clamping height: 10–38 mm Thread: M12 Overall length: 100 mm Clamping screw: M12 x 14 x 100 mm A: 20 mm B2: 40 mm E1: 21 mm E2: 40 mm LS: 49 mm Special features For T-slot 14 mm fixtures Adjustable clamping height 10–38 mm Supplied clamping screw M12 x 14 x 100 mm Compact footprint for confined fixturing FAQ Is this clamp compatible with 14 mm T-slots? Yes. The AMF clamping jaw Nr. 6314V (SKU 4000833073NW) is designed specifically for 14 mm T-slots and mates with common T-slot profiles. Is the clamping screw included with the jaw? Yes. The unit is supplied with a matched clamping screw: M12 x 14 x 100 mm for immediate installation. What workpiece thicknesses can be clamped? The clamping range covers 10–38 mm, enabling secure holding of a wide variety of workpiece heights without additional shimming. Is the component suitable for industrial production use? The jaw is built for repetitive workshop and production use, with standardised threads and dimensions to support reliable, repeatable workholding. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
14mm ER 16-GB Collet With 11mm Internal Square For Thread Cutting, 15 µm Runout - TECWERK
Data inconsistency detected: the fields 'typ' (ER 16-GB) and 'label' (Spannzange ER32-GB) contradict each other. Please verify the product data for SKU 2000834977NW; a product description cannot be generated from inconsistent information, as this issue may lead to confusion or errors in the product catalogue, potentially affecting customer understanding and purchase decisions. It is essential to ensure that all fields in the database are accurate, consistent, and aligned with the product specifications to maintain data integrity and avoid complications during the listing or sales process. Kindly review and correct the discrepancies to ensure the information provided is both reliable and precise.
14mm ER Collet ER40 Clamping Range Nennmaß Minus 1.0mm, L46mm - TECWERK
High-precision clamping with a 14 mm nominal bore and a guaranteed 5 µm runout provides consistent tool performance; the compact 46 mm length enables flexible mounting in tight assemblies. Order the TECWERK ER 40 collet directly via Metav Werkzeuge or ask our consultants if needed. Collet ER 40/472 E — ER 40 collet, 14 mm clamping diameter (TECWERK) The Collet ER 40/472 E by TECWERK is a precision ER 40 collet designed for secure clamping of tools in standard ER collet chucks across machining centres and toolholders. *Conforms to DIN 6499‑B standard *Precision runout of 5 µm *Full-length tool support for stable clamping *Compatible with ER 40 collet chucks Consistent concentricity for repeatable machining The collet delivers a runout of 5 µm, ensuring that cutters and toolholders run concentrically under load. This level of accuracy reduces vibration and tool wear, which leads to fewer rejects and longer tool life. The design permits clamping over the full length of the tool shank, so radial support is maximised; smaller-diameter tools can be clamped securely because the span bridging is nominal minus 1.0 mm, allowing safe gripping of slightly undersized shanks without loss of stability. Faster set-up and broad compatibility save cycle time Built to DIN 6499‑B, the clamping sleeve mates reliably with standard ER chucks, eliminating guesswork when replacing or upgrading holders. No intermediate sizes are required, which simplifies inventory and reduces changeover complexity on the shop floor. The ability to clamp on the lead chamfer as well as the straight shank shortens set-up procedures and keeps spindle downtime to a minimum, supporting efficient production runs. Compact form and robust holding for everyday workshop use With a length of 46 mm, an outer diameter of 41 mm and a clamping bore of 14 mm, this ER 40 collet offers a compact footprint while maintaining high clamping force. The geometry holds tools securely across the entire clamping surface, which helps to prevent slippage under heavy cutting conditions. The solid construction and standardised dimensions make the sleeve straightforward to fit into existing tool management processes, providing a dependable component for precision work. Discuss workshop compatibility and availability with Metav Werkzeuge: email info@metav-werkzeuge.com or call +49 2822 7131930 for tailored technical advice on the TECWERK ER 40 collet (SKU 2000832974NW) Technical data Article number: 2000832974NW Type: ER 40 Label: Collet ER 40/472 E — clamping diameter 14 mm Product type: ER collet Manufacturer: TECWERK Packaging unit: 1 Core specifications Clamping diameter: 14 mm Length L: 46 mm Inner diameter d: 14 mm Outer diameter D: 41 mm Runout / repeatability: 5 µm Span bridging: nominal minus 1.0 mm Special features According to DIN 6499‑B Compatible with ER collet chucks No intermediate sizes required Tools held over the full clamping length Can be clamped on the lead chamfer FAQ What tolerance can be expected for concentricity with this collet? The TECWERK Collet ER 40/472 E is specified with a runout/repeatability of 5 µm, which supports high-precision machining and reduced tool wear in demanding operations. Is the collet compatible with standard ER 40 chucks? Yes — the sleeve conforms to DIN 6499‑B and is designed for use with standard ER 40 collet chucks, ensuring straightforward interchangeability in existing toolholding systems. What does “span bridging: nominal minus 1.0 mm” mean for clamping smaller shanks? The specification "nominal minus 1.0 mm" indicates that the collet can securely bridge and clamp shafts up to 1.0 mm below the nominal diameter, allowing slightly undersized tools to be gripped safely without additional adaptors when using the TECWERK ER 40 collet. Can the tool be clamped on the chamfer or only on the straight shank? The design permits clamping on the lead chamfer as well as on the straight section of the shank, enabling flexible set-up options and improved holding for tapered or chamfered tool ends with the TECWERK ER 40/472 E collet. Manufacturer/Responsible: NORDWEST Handel AG, Robert-Schuman-Straße 17, 44263 Dortmund
14mm ER25 Collet, 34mm Length, 5 µm Runout Accuracy - TECWERK
High-precision clamping with reliable repeatability and full-length tool support ensures consistent machining results; the ER 25 collet delivers 5 µm runout accuracy and secure holding over the entire clamping length, reducing setup time and scrap. Order the collet directly via Metav Werkzeuge or contact our consultants for application advice. TECWERK ER 25 Collet (Type ER 25/430 E) — 14 mm clamping diameter, DIN 6499‑B The TECWERK ER 25 Collet (Type ER 25/430 E) is a precision ER collet designed for secure clamping of 14 mm tool shanks in ER 25 collet chucks, suitable for production and workshop environments Precision runout ≤ 5 µm Clamping diameter 14 mm Holds tools along full clamping length Compatible with ER 25 collet chucks Reliable precision for demanding machining The ER 25 collet is manufactured to DIN 6499‑B, delivering a runout and repeatability of 5 µm, which translates into noticeably better surface finish and reduced tool wear in high-precision operations. Such tolerance stability ensures that concentricity is maintained across repeated setups, helping to lower scrap rates and increase first-pass yield. The standardised specification also simplifies quality documentation and process validation in industrial environments. Secure holding along the entire clamping length This clamping sleeve holds cutting tools along the full clamping length, which reduces the risk of axial or radial slip during operation and improves dynamic stability at higher spindle speeds. The ability to clamp on the guiding chamfer further enhances versatility: shorter shanks or slightly chamfered tools remain securely seated, so changeover is faster and fixturing becomes more predictable. The result is consistent cutting performance and lower tool-change downtime. Compact dimensions and straightforward compatibility With compact external and internal dimensions — L: 34 mm, d: 14 mm, D: 26 mm — the collet fits seamlessly into standard ER 25 chucks without the need for intermediate adapters. The collet permits a clamping diameter bridging of nominal −1.0 mm, meaning it can accommodate small deviations in tool shank diameter without requiring a secondary size, which simplifies inventory and reduces the number of items held in stock. Compatibility with common ER systems ensures straightforward integration into existing tooling setups. Designed for efficient workshop and production use Engineered for repeatable performance, the collet supports streamlined workflows in both single-machine shops and production lines. The ER 25 geometry and DIN conformity reduce decision time for procurement and make inventory management easier, while its robust clamping behaviour supports longer uninterrupted runs. For maintenance and reconditioning, the standard format allows easy replacement, keeping machines productive and maintenance cycles predictable. For secure, repeatable clamping choose the TECWERK ER 25 collet and contact Metav Werkzeuge for prompt supply and technical guidance — email info@metav-werkzeuge.com or call +49 2822 7131930 Technical Data Article number: 2000832935NW Type: ER 25 Product: ER collet Brand: TECWERK Facts Clamping diameter: 14 mm L: 34 mm d: 14 mm D: 26 mm Runout/repeatability: 5 µm Clamping diameter bridging: nominal −1.0 mm Special features Standard: DIN 6499‑B Compatible with ER collet chucks Tools held along full clamping length Can be clamped on guiding chamfer Packaging unit: 1 FAQ What runout tolerance can be expected from this collet? The TECWERK ER 25 collet (SKU 2000832935NW) offers a runout and repeatability of 5 µm when used with a correctly mounted ER 25 chuck and properly prepared toolholders. Is the collet compatible with standard ER 25 chucks? Yes — the collet is made to the ER 25 specification and is compatible with ER 25 collet chucks conforming to DIN 6499‑B. Can tools be clamped on the chamfer or only on the cylindrical shank? The collet is designed so that tools can be held along the full clamping length and may also be clamped on the guiding chamfer for shortened or chamfered shanks. What are the key dimensions to check before ordering? Check the essential dimensions: L 34 mm, d 14 mm, D 26 mm, and the clamping diameter 14 mm; the collet allows bridging down to nominal −1.0 mm. Which standard does this collet conform to? This collet conforms to DIN 6499‑B, ensuring standardised interface and interchangeability with ER 25 systems. Manufacturer / Responsible: NORDWEST Handel AG, Robert-Schuman-Straße 17, 44263 Dortmund
14mm ER32 Collet Precision Clamping Capacity Nennmaß Minus 1.0mm, L 40mm - TECWERK
Take advantage of the combination of standardised compatibility, high runout accuracy and secure full‑length clamping for consistent machining results; order the TECWERK ER 32 collet directly via Metav Werkzeuge or consult our specialists for tailored advice. TECWERK ER 32 collet – clamping diameter 14 mm, runout 5 µm TECWERK ER 32 collet for ER collet chucks, designed to provide rigid tool retention and precision clamping in workshop and production environments DIN 6499‑B compatibility for ER chucks Full-length clamping for secure tool retention Runout and repeatability: 5 µm Clamping diameter bridging: nominal −1.0 mm Precision standards that reduce setup time and scrap The TECWERK ER 32 collet is manufactured to DIN 6499‑B dimensions, ensuring straightforward interchangeability with standard ER collet chucks. Adherence to the standard simplifies spindle tooling management and reduces the need for special adaptors. The specified runout and repeatability of 5 µm translate into tighter tolerances on finished components, fewer rejects and more consistent batch quality. For operations where repeatability and predictable tool behaviour are essential, the standard compliance delivers measurable production benefits. Improved rigidity and tool life through full‑length clamping Because the insert holds tools along the full clamping length, cutting forces are distributed more evenly and lateral play is minimised. This full‑length clamping capability, together with the option to clamp on the lead‑in chamfer, reduces vibration and tool deflection during milling, drilling and finishing passes. The result is prolonged cutter life and more stable machining, which supports higher material removal rates and lower total tool costs over time. Flexible handling of tool diameter variations and compact dimensions The collet allows clamping diameter bridging of nominal −1.0 mm, so small mismatches between nominal tool shank sizes can be accommodated without intermediate sizes. This feature streamlines tooling inventories and quickens changeovers. Compact physical dimensions (L: 40 mm, d: 14 mm, D: 33 mm) make the insert suitable for standard ER 32 applications where space is limited but precision is required. The compact design supports straightforward storage and fast replacement in a production setting. Practical advantages for procurement and workshop workflows Standardisation with the ER system reduces supplier complexity and eases procurement: the collet fits established ER fixtures and can be stocked as a modular component. The clear technical specification and measurable tolerances support purchasing decisions based on performance metrics rather than subjective claims. For workshops seeking to democratise precision—achieving dependable measurement and clamping quality without excessive overhead—the use of standard, well‑specified components contributes directly to operational reliability. Choose the TECWERK ER 32 collet for dependable 5 µm runout and robust full‑length clamping, and contact Metav Werkzeuge for supply and expert advice from Emmerich. Technical data Article number: 2000832951NW Type: ER 32 Product designation: ER 32 collet (clamping diameter 14 mm) Brand: TECWERK Core technical data Clamping diameter: 14 mm Length (L): 40 mm Internal diameter (d): 14 mm Outer diameter (D): 33 mm Runout / repeatability: 5 µm Clamping diameter bridging: nominal −1.0 mm Special features Compatibility with DIN 6499‑B Fits ER collet chucks Holds tools along entire clamping length Can be clamped on the lead‑in chamfer No intermediate sizes required FAQ What level of precision can be expected from this collet? The TECWERK ER 32 collet is specified with runout and repeatability of 5 µm, providing stable concentricity for high‑precision machining tasks. Is this collet compatible with standard ER chucks? Yes; the collet conforms to DIN 6499‑B and is designed for use in standard ER collet chucks. Can the collet accommodate slightly undersized tool shanks? The collet allows clamping diameter bridging of nominal −1.0 mm, permitting minor size variations without the need for intermediate inserts. What are the physical dimensions of the clamping sleeve? Key dimensions are L: 40 mm, internal diameter d: 14 mm and outer diameter D: 33 mm. Does the collet support clamping on the lead‑in chamfer? Yes; the design permits clamping on the lead‑in chamfer, enabling secure retention even when the shank is engaged on the guide bevel. Manufacturer / Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund
14mm Pneumatic Push Rod Clamp 2,500N Thrust, 3,200N Holding, Zinc-Plated - Kukamet
Take advantage of the combination of reliable pneumatic actuation, a pressing force of 2,500 N and a compact, zinc‑plated design for secure, repeatable clamping in production environments. Order the Pneumatic Push‑Rod Clamp 661 directly via Metav Werkzeuge or ask our consultants if technical advice is required. Pneumatic Push‑Rod Clamp 661 — Kukamet, 2,500 N pressing force, zinc‑plated Pneumatic Push‑Rod Clamp 661 is a compact pneumatic clamp for fixture and jig applications, designed for horizontal mounting and robust production use Pneumatic push‑rod clamp »661« by Kukamet Zinc‑plated housing, corrosion resistance Pressing force 2,500 N; holding force 3,200 N Horizontal foot mounting; piston Ø14 mm Predictable clamping performance for automated workflows The Pneumatic Push‑Rod Clamp 661 delivers a defined pressing force of 2,500 N and a holding force of 3,200 N, ensuring repeatable clamping across cycles. Pneumatic actuation converts compressed air into linear motion via the piston; the result is a fast, controllable thrust that secures workpieces without manual intervention. This controlled force reduces scrap rates and supports tighter process tolerances, which benefits assembly lines and CNC setups that require consistent part position and clamping pressure. Compact design that fits tight fixtures and reduces integration time A horizontal foot mounting and piston Ø14 mm make this clamp straightforward to fit into space‑restricted fixtures. The zinc‑plated finish provides basic corrosion resistance and a clean assembly appearance, while a weight of 1.026 kg keeps the component light for movable or modular tooling plates. The compact actuator profile minimises interference with adjacent tooling; as a result, fixture layouts can be denser without sacrificing access or serviceability. Low-maintenance operation and reliable material choice Constructed with a zinc‑plated housing and simple pneumatic internals, the actuator is engineered for long running intervals with minimal upkeep. Routine checks of the compressed air quality and seals are typically sufficient to maintain performance. The clear numeric values for force and piston size support compatibility checks with existing valves and tubing, aiding rapid replacement or retrofitting. Backed by Kukamet manufacturing and Metav’s supply chain, the unit contributes to dependable uptime in workshop and industrial environments. For secure, repeatable clamping with Kukamet’s Pneumatic Push‑Rod Clamp 661, contact Metav Werkzeuge for ordering and expert advice: info@metav-werkzeuge.com or +49 2822 7131930 Technical data SKU: 661-3-Q14 GTIN: 8680731503128 Manufacturer: Kukamet Model: 661 Facts Pressing force: 2,500 N Holding force: 3,200 N Piston diameter: 14 mm Weight: 1.026 kg eClass: 21041716 ETIM: EC011973 Special features Zinc‑plated Horizontal foot mounting Pneumatic push‑rod actuation FAQ What clamping and holding forces does the clamp provide? The Pneumatic Push‑Rod Clamp 661 offers a pressing force of 2,500 N and a maximum holding force of 3,200 N suitable for many fixture applications. How is the clamp mounted in a fixture? Mounting is by a horizontal foot; the design permits installation on flat tooling plates and is compatible with common fixture layouts. What is the piston diameter and why does it matter? Piston diameter is 14 mm; this dimension determines the actuator’s stroke force characteristics and helps when selecting matching valves and tubing. Is the clamp suitable for corrosive workshop conditions? The unit is zinc‑plated, providing basic corrosion resistance; for aggressive environments, consider additional surface protection or environmental controls. Who supplies the product and where can it be ordered? The clamp is produced by Kukamet and is available through Metav Werkzeuge; refer to SKU 661-3-Q14 when ordering. Manufacturer: Kukamet Fevzi Çakmak Mah.10644 Sk. No:61-63 42050 Karatay / KONYA TÜRKİYE / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com
Secure components with reliable workpiece clamps
Workpiece clamps, also known as workholding clamps or workholding devices, form the essential mechanical interface between machine and part in industrial fabrication. They keep components absolutely play-free, positionally accurate and vibration-resistant during milling, turning, drilling or grinding.
How workpiece clamps ensure process stability
A correctly specified clamping concept transfers the high cutting and feed forces of modern CNC machines into the machine table or spindle without deforming the part. The right combination of mechanical, hydraulic, pneumatic or magnetic solutions enables fast, repeatable setups and supports automated part change where required. Typical applications range from single-part turning to high-volume series milling and complex five-axis machining.
Concrete production benefits at a glance
- repeatable positioning: reduces scrap and rework
- high clamping forces: withstands aggressive cutting without part movement
- reduced set-up time: modular systems and quick-change features speed throughput
- improved surface finish: vibration damping for finer results and tighter tolerances
- flexible compatibility: vices, chucks, clamping plates and zero-point systems for diverse geometries
Why Metav's range is the practical choice
Metav combines decades of specialist know-how with a broad, handpicked range that democratises precision for workshops and industry alike. Based in Emmerich, Metav acts as a quality filter for the European market and supplies more than 250,000 products from precision metrology to complete workshop equipment. With the trust of over 48,000 customers, Metav offers a single-source approach that reduces supplier complexity and secures dependable delivery to your workbench.
Technical data
- function: mechanical interface between machine and workpiece
- primary requirements: absolute positional accuracy; vibration reduction; high clamping forces
- technologies: mechanical, hydraulic, pneumatic, magnetic
- typical components: machine vices; chucks; clamping plates; zero-point systems; pratzen; clamping jaws
- application areas: milling; turning; drilling; grinding; automated part change systems
- production benefits: reduced set-up time; enhanced process security; optimised series and single-part production
The practical summary
Workpiece clamps bring the stability and repeatability required to meet tight tolerances and excellent surface quality, making them indispensable across machining operations. Choosing the right workholding clamps and modular workholding devices is a decisive step towards higher productivity and consistent part quality.
FAQ
What types of workpiece clamps are suitable for automated machining?
Workholding clamps with quick-change modules, hydraulic actuation or magnetic systems are commonly used for automated machining. These workholding devices enable fast, repeatable part changes and integrate with zero-point systems.
How do workpiece clamps affect surface finish and tolerances?
A stable clamping concept minimises vibration and part movement; this improves surface finish and supports achieving narrow tolerances when using high-precision workpiece clamps or workholding devices.
Can the same workpiece clamps handle different part geometries?
Modular workholding clamps and adaptable clamping jaws allow flexible fixturing for varied geometries; combining vices, clamping plates and pratzen increases versatility on the shopfloor.
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com