Secure and precise workholding for metalworking productivity
Workholding devices such as workpiece clamps and chuck systems provide absolute positional stability and vibration damping during milling, turning, drilling and grinding, ensuring parts remain free of play under high CNC cutting and feed forces. By transferring clamping loads into the machine table or spindle without deforming the component, a well engineered workholding solution improves machining accuracy, surface finish and process reliability while reducing set-up times. Modular systems from machine vices and chucks to zero-point systems and specialised fixtures enable fast changeovers and support both serial and single-part production, delivering consistent clamping force, repeatability and enhanced throughput.
200mm Horizontal Clamp 90° Three-Point Massive Holding Arm Safety Lock, 3.5kN Clamp Force - Kukamet
Robust clamping with a massive support arm, 200 mm reach and a secure safety latch ensures reliable fixture performance; combined with a clamping capacity of 3,500 N and a holding force of 3,650 N, this configuration supports repeatable setups and efficient production. Order the 111 horizontal lever clamp directly via Metav Werkzeuge or consult their specialists for application advice. 111 Horizontal lever clamp by Kukamet — 200 mm arm, safety latch 111 is a horizontal lever clamp engineered for secure 90° fixture clamping in jigs and workholding applications, combining a compact footprint with a heavy-duty support arm and mechanical safety lock Massive support arm with safety latch 200 mm arm for extended reach Horizontal base for secure fixture mounting Holding force up to 3,650 N Durable hold for repetitive production tasks The clamp delivers a consistent holding force that suits repetitive clamping cycles in assembly and machining jigs. The combination of a sturdy support arm and a mechanical safety latch reduces the risk of accidental release, translating into reliable repeatability on production lines and in fixture construction. The robust construction and compact geometry permit installation where space is limited while maintaining the force levels required for secure workholding. Practical mounting and material finish for workshop use Designed with a horizontal base for straightforward mounting, the device integrates easily into existing fixture plates and tooling frames. The blackened finish offers basic corrosion resistance and a low-reflective surface that is advantageous in machining environments. The compact mass of the unit and the 200 mm reach balance rigidity and accessibility, enabling secure clamping without excessive bulk on the workbench or fixture assembly. Safety and mechanical advantages for process stability A positive mechanical safety latch prevents unintended opening during vibration or incidental contact, improving operational safety and reducing downtime from repositioning. The lever-style actuation yields fast engagement and visible locked status, supporting efficient setup changes and minimising the time spent on manual securing. These features contribute to a stable production flow and reduced cycle variability in repetitive tasks. Specified performance for accurate expectations With measured values for clamping and holding force, the clamp provides objective data to match application requirements. The clear specification of 3,500 N clamping force and 3,650 N holding force allows planners and engineers to verify suitability for specific workpieces and processes. The 90° clamping angle and the 200 mm arm length offer defined geometric parameters for fixture design and CAD integration. For secure and reliable fixture clamping with Kukamet’s robust 200 mm arm and safety latch, contact Metav Werkzeuge in Emmerich for tailored advice and fast supply. Technical data Article number: B111-4-D-L-C3 Manufacturer: Kukamet Category: Clamp Facts Arm length: 200 mm Weight: 0.73 kg Max clamping force: 3,500 N Max holding force: 3,650 N Angle: 90° Special features Fastening: horizontal base Finish: blackened Massive support arm Safety latch SKU: B111-4-D-L-C3 FAQ What clamping and holding forces does the clamp provide? The Kukamet 111 horizontal lever clamp specifies a clamping force of 3,500 N and a holding force of 3,650 N, values intended for secure fixture retention in repetitive operations. How is the clamp mounted in a fixture? Mounting is by a horizontal base, allowing the clamp to be bolted to fixture plates or tooling frames for stable integration into jigs and assemblies. Is the arm length suitable for larger workpieces? The 200 mm arm gives extended reach for many fixture layouts while keeping the overall footprint compact; the lever design supports rapid engagement and release. Which safety features prevent accidental release? A dedicated safety latch secures the lever in the closed position, reducing the risk of unintended opening under vibration or incidental impact. What surface finish does the clamp have? The component is supplied with a blackened finish, providing basic corrosion resistance and a non-reflective surface suited to workshop environments. Manufacturer: Kukamet Fevzi Çakmak Mah.10644 Sk. No:61-63 42050 Karatay / KONYA TÜRKİYE / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com
200mm Horizontal Clamp With Massive Holding Arm, 90° Pivot, 3.65kN Holding Force - Kukamet
Take advantage of the combination of robust clamping force, a 200 mm heavy-duty arm and a compact, low-weight design for reliable fixture performance. Order the horizontal toggle clamp directly via Metav Werkzeuge or contact our consultants for integration advice. Horizontal toggle clamp 111 — 200 mm arm, 3.65 kN holding force (Kukamet) The horizontal toggle clamp 111 secures workpieces at a 90° clamp angle for jigs, fixtures and assembly applications where quick, repeatable clamping is required. Massive 200 mm holding arm Holding force 3.65 kN Horizontal foot for plate mounting Blackened finish for corrosion resistance Secure clamping with measurable performance The 111 is engineered as a toggle clamp that converts lever movement into consistent clamping pressure, delivering a holding force of 3.65 kN and a closing force of 3.50 kN. This distinction means the device provides persistent retention once engaged while the actuation requires lower input force, improving operator ergonomics and reducing cycle time. The 200 mm arm offers extended reach for deeper fixtures, enabling stable contact on larger components without compromising repeatability. The compact weight of 0.847 kg keeps the fixture assembly light while retaining industrial robustness. Easy mounting and fixture integration Designed with a horizontal foot, the clamp mounts flush to fixture plates or baseboards for straightforward integration into production jigs. The 90° toggle position gives a clear, fixed clamping orientation that simplifies locating and aligning workpieces, reducing setup time. The horizontal configuration is especially suitable for assembly benches and welding fixtures where lateral access is preferable. The clamp’s form factor supports modular layouts and allows the clamping point to be positioned precisely, translating directly into improved process reliability. Durable finish and low maintenance for long service life A blackened finish protects the mechanism against mild corrosion and wears well in workshop environments, while the massive holding arm is designed to resist bending under repeated load. The toggle mechanism is simple by design, minimising failure points and easing routine inspections; lubrication intervals are extended thanks to the robust construction. Because the clamp is mechanically straightforward, spare parts and replacements can be managed economically, supporting continuous operation and lowering total cost of ownership. Contact Metav Werkzeuge to discuss how the Kukamet horizontal toggle clamp 111 fits specific fixtures and to secure supply from Emmerich — call +49 2822 7131930 or email info@metav-werkzeuge.com Technical data Article number: B111-4-D-C3 GTIN: 8680731507058 Manufacturer: Kukamet Model: 111 Facts Arm length: 200 mm Clamping force (closing): 3,500 N Holding force: 3,650 N Weight: 0.847 kg Clamp angle: 90° Special features Massive holding arm Horizontal foot mounting Blackened finish (Schwarz brüniert) Compact, low-weight design Category: Clamps FAQ How is the clamp mounted to a fixture? The horizontal toggle clamp 111 (Kukamet) is mounted via its horizontal foot, allowing secure plate installation with through-bolts or countersunk screws depending on the fixture design. What forces can be expected in operation? Rated values are a closing force of 3,500 N and a holding force of 3,650 N; these figures for the Kukamet 111 describe actuation demand versus sustained retention once engaged. Is the clamp suitable for frequent cycling in production? Yes, the 111’s simple toggle mechanism and massive holding arm are designed for repetitive use and require only routine inspection and occasional lubrication. Can the clamp reach into recessed fixtures? The 200 mm arm provides extended reach compared with shorter toggles, making the clamp suitable for deeper or slightly recessed clamping points in jigs and assembly fixtures. Where can replacement parts or technical drawings be obtained? Spare parts and technical details for the Kukamet horizontal toggle clamp 111 (SKU B111-4-D-C3) can be requested via Metav Werkzeuge for planning and maintenance purposes. Manufacturer: Kukamet Fevzi Çakmak Mah.10644 Sk. No:61-63 42050 Karatay / KONYA TÜRKİYE / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com
200mm Hydraulic Chuck Three-Point 3600 kgf Clamping Force 0.03mm Accuracy 2000 rpm - Vertex
Secure clamping and precise runout combine to improve process stability on demanding turning tasks; the 200 mm nominal diameter and 3,600 kgf clamping force support firm workpiece retention while the specified accuracy 0.03 mm reduces reject rates. Order the VSK-8 chuck directly via Metav Werkzeuge or ask our consultants if needed. VSK-8 chuck — Vertex 200 mm diameter, 3,600 kgf clamping force The VSK-8 chuck is a heavy-duty workholding device engineered for secure clamping in machining applications, suited to tasks that demand both force and repeatable concentricity 200 mm nominal diameter 3,600 kgf clamping force Runout accuracy 0.03 mm Rated up to 2,000 r.p.m. Secure clamping for continuous production A high clamping force is a cornerstone of reliable machining. With a rated 3,600 kgf, this chuck provides the physical retention needed to resist cutting forces and reduce slippage during operation. The large 200 mm nominal diameter increases the contact area for bigger components, helping to distribute load and lower the risk of local deformation. By prioritising a robust grip, the workholding solution supports longer uninterrupted cycles and fewer manual interventions, which translates into steadier throughput and improved overall equipment effectiveness. Precision that lowers rework and shortens inspection Repeatability is expressed here as accuracy 0.03 mm, a runout figure that indicates how close the clamped centre remains to the spindle axis during rotation. Lower runout means better concentricity between tool and workpiece, which reduces tool wear, improves surface finish and decreases the frequency of rework. For users with limited metrology expertise, runout can be understood as the radial deviation of a rotating part; the smaller the number, the more predictable the machining result. This focus on measurable precision delivers clear time and cost benefits at inspection and in downstream processes. Practical integration for workshop environments Operational limits and handling characteristics matter on the shop floor. The chuck is specified for rotation up to 2,000 r.p.m. and has a mass of 14.7 kg, which influences mounting and balancing decisions during installation. A compact weight facilitates manual handling while remaining substantial enough to ensure structural stability during cuts. The straightforward numeric specifications allow planners to assess compatibility with existing spindles and balancing routines without guesswork. Where certainty is required, the Vertex origin and the provided technical values help to align procurement with in-house process constraints. Contact Metav Werkzeuge in Emmerich for tailored advice on the Vertex VSK-8 chuck and to arrange supply directly from our European quality hub Technical data Article number: VSK-8 GTIN: 4061905095061 ECLASS: 21020590 Brand: Vertex Core specifications Diameter: 200 mm Clamping force: 3,600 kgf Accuracy (runout): 0.03 mm Max speed: 2,000 r.p.m. Weight: 14.7 kg Features Product type: chuck (workholding device) Category: Vertex SKU: VSK-8 Image available FAQ What clamping force does the chuck provide? The VSK-8 chuck delivers a clamping force of 3,600 kgf, designed to secure workpieces against typical turning and machining forces. What is the nominal diameter and how does it affect use? The nominal diameter is 200 mm; larger diameter increases contact area and is beneficial for clamping bigger components with improved load distribution. How should the runout figure be interpreted? The specified accuracy 0.03 mm refers to radial runout; it indicates the maximum expected deviation from true concentric rotation and helps predict surface finish and tool life. What rotational speed is permissible with this chuck? The chuck is rated up to 2,000 r.p.m.; adherence to this limit supports safe operation and maintains the stated accuracy during rotation. Is the chuck suitable for heavy-duty machining tasks? Given the 3,600 kgf clamping force and 200 mm diameter, the chuck is suited for demanding clamping tasks; spindle compatibility and dynamic balancing should be confirmed for specific machine setups. Manufacturer: Vertex Machinery Works Co., Ltd.; No. 296, Sec. 1, Feng Shih Road, Fengyuan District, Taichung City 420, Taiwan
200mm Independent Four-Jaw Lathe Chuck, 1350 rpm, 4-M10 T-Slots - Vertex
Benefit from independent four‑jaw clamping, a 200 mm nominal diameter and a 1,350 r/min rating for reliable turning operations; order the VKC-8 directly via Metav Werkzeuge or consult our advisers if specification support is required. VKC-8 four‑jaw independent chuck (200 mm) by Vertex — 1,350 r/min, 15.9 kg A VKC-8 four‑jaw independent chuck designed for secure, adjustable clamping of irregular and concentric workpieces on lathes and turning centres. Independent four‑jaw clamping for irregular shapes 200 mm nominal diameter Rated up to 1,350 r/min T‑slots 4‑M10 for secure mounting Consistent precision through independent jaw control Independent jaw operation means each jaw can be set separately, allowing secure clamping of non‑cylindrical or off‑centre parts with minimal rework. The independent jaws reduce the need for specialised fixtures when turning irregular shapes, shortening setup times and improving throughput. For shop floors where adaptability matters, the jaw assembly provides repeatable positioning that supports tighter tolerances and fewer scrap parts. The VKC‑8 is engineered to maintain clamping accuracy throughout the machining cycle, contributing directly to consistent part quality. Capacity and dynamic suitability for typical lathe work With a 200 mm diameter capacity and a rated speed of 1,350 r/min, the chuck covers a broad range of medium‑sized turning tasks while matching common spindle speeds on universal and CNC lathes. The specified maximum speed indicates the dynamic operating envelope; within this range the device balances performance and safety. Selecting a chuck with matching diameter and speed rating helps avoid unnecessary spindle loading and supports stable cutting conditions, which in turn improves surface finish and tool life. Practical mounting and workshop integration for faster set‑up Mounting is simplified by T‑slots 4‑M10, which provide defined attachment points for adapter plates or bespoke fixtures, enabling rapid changeovers between jobs. The design reduces fixturing complexity and integrates easily into existing workholding systems. Clear numeric specifications for diameter, speed and fastening standardise procurement and spare‑part planning across the workshop, supporting efficient inventory control and predictable machine availability. For dependable, flexible clamping choose the Vertex VKC‑8—contact Metav Werkzeuge in Emmerich for specification advice and reliable supply Technical data SKU: VKC-8 GTIN: 4061905087295 ECLASS: 21020490 Manufacturer: Vertex Core specifications Diameter: 200 mm Max. speed: 1,350 r/min Weight: 15.9 kg T‑nuts: 4‑M10 Special features Independent four‑jaw design Image available (thumbnail asset) FAQ What is the maximum rotational speed for this chuck? The VKC‑8 four‑jaw independent chuck is rated to 1,350 r/min, which defines its recommended dynamic operating limit. Can the chuck clamp irregularly shaped parts without additional fixtures? Yes. The independent jaw concept allows each jaw to be adjusted individually, making the chuck suitable for irregular and off‑centre workpieces without specialised fixtures. What mounting interface does the chuck use? Mounting is provided via T‑slots 4‑M10, permitting secure attachment to compatible adapter plates or faceplates. What size of workpiece can be accommodated? The chuck has a nominal diameter of 200 mm, specifying the standard clamping envelope for concentric and irregular parts. Who manufactures the VKC‑8 and where is it supplied from? The VKC‑8 is produced by Vertex and is available via Metav Werkzeuge, which supplies and supports precision workholding equipment for European workshops. Manufacturer: Vertex Machinery Works Co., Ltd.; No. 296, Sec. 1, Feng Shih Road, Fengyuan District, Taichung City 420, Taiwan
200mm Jaw Set For Chuck, 3-Piece Set - RÖHM
Take advantage of the combination of hardened construction, straightforward replacement and compatibility with standard 200 mm chucks for reliable clamping and reduced downtime — order this jaw set directly via Metav Werkzeuge or consult the technical team for fitment details. RÖHM base jaw set for 200 mm chuck — hardened, 3-piece The RÖHM base jaw set for 200 mm chuck is a hardened set of replacement jaws designed for secure workholding on standard 200 mm chucks in machining and turning applications. Hardened construction for extended service life Compatible with 200 mm chucks Set of three jaws for complete assembly Consistent, precision clamping for series production The hardened jaw geometry and contact faces are engineered to deliver consistent clamping force, helping to maintain concentricity during turning and machining cycles. This stability reduces rework and supports repeatable tolerances in batch production. As a result, cycle-to-cycle variation is minimised, which enhances process reliability and aids quality assurance in metalworking and general workshop environments. Fast replacement to keep machines productive Supplied as a set of three, the jaws are intended for direct replacement of worn components, enabling swift maintenance without time-consuming adjustments. The complete set format simplifies stocking and spares planning, which in turn limits machine downtime and streamlines ordering. Clear identification of the item and fitment for 200 mm chucks makes procurement and inventory control more efficient for production planners. Durable service life and broad workshop suitability The hardened treatment increases wear resistance and extends service intervals, making these jaws a cost-effective choice for everyday workshop use. The combination of robust material treatment and precise manufacturing supports secure gripping of workpieces during roughing and finishing operations, contributing to safer, more predictable machining. The brand reputation further underpins a dependable supply chain for precision partners. For secure procurement and to confirm compatibility with specific chuck models, contact Metav Werkzeuge — specialists in precision workshop supplies — for tailored advice and order placement via info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: 4121273200NW SKU / UID: 4121273200NW Manufacturer: RÖHM Product type: Base jaw set Core specifications Chuck diameter: 200 mm Set contents: 3 pieces Packaging unit: 1 Features & compatibility Hardened design Suitable for 200 mm chucks Replacement jaws for standard lathe chucks FAQ What chuck size is this jaw set made for? This base jaw set is specified for use with a 200 mm chuck and is marked as suitable for that chuck diameter. How many jaws are included in the set? The delivery comprises three jaws; the complete set of three ensures a full jaw assembly for the chuck. Are the jaws heat-treated or surface-hardened? The RÖHM base jaw set is supplied in a hardened condition to improve wear resistance and durability under machining loads. Is this set a direct replacement for standard RÖHM chucks? The jaw set is designed for compatibility with 200 mm chucks; confirmation of direct fitment to a specific chuck model can be obtained from Metav Werkzeuge. Can these jaws be used for heavy-duty turning and finishing operations? The hardened construction supports both roughing and finishing operations by providing sustained clamping performance and reduced wear Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
200mm Jaw Set for Chuck, Stepped Hardened Jaws, 3 Pieces - RÖHM
Take advantage of a hardened, stepped jaw design and precise compatibility with a 200 mm chuck to secure workpieces reliably; the three-piece set reduces changeover time and simplifies setup. Order the jaw set directly via Metav Werkzeuge or request advice from our consultants if additional information is required. RÖHM jaw set for 200 mm chuck — hardened stepped jaws, 3-piece set The RÖHM jaw set for 200 mm chuck delivers hardened, stepped jaws intended for secure clamping in turning and chucking applications on compatible 200 mm chucks. Hardened stepped jaws for repeatable clamping Designed for 200 mm chuck diameter Includes three interchangeable jaws per set Precision-ground seating for secure fit Optimised clamping for efficient turning operations The stepped jaw geometry offers a compact solution for multiple gripping diameters, reducing the need for frequent jaw changes. Constructed for secure clamping on a 200 mm chuck, the set forms a stable contact that improves cycle consistency and lowers the risk of slippage. By combining a hardened surface with precision seating, the assembly supports longer service intervals while maintaining positional accuracy in repetitive turning tasks. Consistent repeatability and straightforward handling A three-piece configuration provides modular replacement and simple indexing during setup, which helps to shorten machine downtime. The 3-piece set allows each jaw to be mounted and aligned individually, guaranteeing consistent clamping forces and precision across repeated workpieces. For users unfamiliar with stepped jaws: the design includes discrete gripping steps so a single set can handle several nominal diameters without additional accessories. Practical integration into workshop workflows Compatibility with a 200 mm chuck makes this jaw set suitable for a range of lathes and clamping fixtures that accept standard chuck inserts. The robust construction and stepped profile support both roughing and finishing operations where hold and repeat accuracy matter. As a compact, replaceable component, the set contributes to predictable set-up procedures and helps maintain throughput when used alongside regular maintenance practices. For precision clamping with the RÖHM hardened stepped jaws, contact Metav Werkzeuge for a tailored quotation or technical guidance via info@metav-werkzeuge.com or call +49 2822 7131930. Technical data Article number: 4121269200NW SKU: 4121269200NW Brand: RÖHM Facts Chuck diameter: 200 mm Set contents: 3 pieces Packaging unit: 1 Special features Hardened stepped jaws Suitable for 200 mm chuck Clamping application for turning Precision-ground seating FAQ Are these jaws compatible with any 200 mm chuck? Compatibility depends on the chuck's jaw seat and mounting standard; the jaw set is designed for chucks that accept standard 200 mm jaw inserts and mounting geometry, as indicated by the product data for the RÖHM jaw set (SKU 4121269200NW) What does "stepped jaws" mean in practice? Stepped jaws provide discrete gripping steps so that a single jaw can clamp several nominal diameters; the RÖHM stepped jaws enable versatile clamping without frequent jaw swaps How many pieces are supplied in one set? The delivery comprises a three-piece set; each set contains three interchangeable jaws for staged installation Are the jaws hardened for heavy-duty work? Yes, the jaws are specified as hardened, offering improved wear resistance and sustained clamping performance in typical turning operations Can the jaws be reworked or ground to fit? Modifying hardened jaws is possible but requires appropriate tooling and expertise; any rework should preserve the seating and clamping surfaces to maintain the set's precision Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
200mm Machine Table Clamp 100mm Reach 19.5x9.5mm Rail Slot - BESSEY
Take advantage of robust clamping performance with a 200 mm clamping height and a 100 mm throat, combined with a compact rail profile for stable machine-table integration; order the BESSEY clamp directly via Metav Werkzeuge or consult our specialists for fitment advice. BESSEY machine table clamp – 200 mm clamping height, 100 mm throat BESSEY machine table clamp designed for reliable workholding on machine tables and milling fixtures, offering a tall clamping range and narrow rail profile for compact installations. Clamping height 200 mm Throat depth 100 mm Rail cross-section 19.5 x 9.5 mm Industrial BESSEY construction High clamping range for versatile setups The BESSEY machine table clamp provides a clamping height of 200 mm, enabling secure fixation of components with significant profile height while maintaining easy access for tooling. This tall clamping capacity translates into fewer secondary operations and reduced setup time, which supports a steady production flow. The specification for throat depth of 100 mm allows firm holding closer to the workpiece centre, improving stability during machining and helping to maintain precise repeatability across batches. Compact rail profile for stable, space-saving mounting A narrow rail cross-section of 19.5 x 9.5 mm ensures the clamp integrates neatly into existing T-slot or machine table rails without occupying excessive space. The slim profile is advantageous where table real estate is limited, yet the design retains necessary stiffness for secure clamping. The combination of compact form and high clamping reach provides a practical balance between accessibility and rigidity, supporting accurate machining with minimal interference from the clamping hardware. Durable build and workshop-friendly operation Built to industrial expectations, this clamp emphasises robust construction and straightforward handling for daily workshop use. The engineered geometry concentrates clamping forces where required, reducing slippage and wear. For procurement and maintenance planning, the unit is supplied as a single pack, simplifying inventory control. Metav’s position as a precision partner further contributes to supply reliability, with stock and logistics aimed at keeping operations moving without compromise. Contact Metav Werkzeuge to confirm compatibility with existing fixtures and arrange prompt supply directly from Emmerich. Technical data Article number: 4123740020NW Brand: BESSEY Type: Machine table clamp Label: Maschinentischspanner Spann-H.200mm A.100mm Schienen-Q.19,5x9,5mm BESSEY Packaging unit: 1 Facts Clamping height: 200 mm Throat depth / reach: 100 mm Rail cross-section: 19.5 x 9.5 mm Special features Industrial-grade design Suitable for machine table mounting Compact rail profile for space-saving installation FAQ Is this clamp suitable for standard T-slot machine tables? The clamp is designed for machine table mounting and the BESSEY machine table clamp with its 19.5 x 9.5 mm rail profile can be integrated into many table systems; check slot compatibility to ensure a secure fit. How much clamping height does the unit offer? Clamping height is 200 mm, allowing the clamp to secure taller workplaces and fixtures while maintaining access for tooling operations. What is the throat depth and why does it matter? The throat depth is 100 mm; a deeper throat places the clamping force nearer the centre of the workpiece, increasing stability during machining. Does the package include additional mounting hardware? The product is supplied as a single unit (packaging unit: 1); any additional mounting adapters should be verified against the machine table specifications. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
200mm Machine Table Clamp 120mm Throat, 28x11mm Rail Section - BESSEY
Combining a 200 mm clamping height, a 120 mm reach and a 28 x 11 mm rail cross-section, the BESSEY machine table clamp delivers reliable, repeatable workholding for machining tables; order directly via Metav Werkzeuge or consult the specialists for specification support. BESSEY Machine table clamp — 200 mm clamping height BESSEY Machine table clamp for secure vertical clamping on machine tables, designed for precise and stable workholding in industrial workshops 200 mm clamping height for tall setups 120 mm reach for deep workholding 28 x 11 mm compatible rail cross-section Industry-grade construction by BESSEY Stable holding for precise machining operations The combination of a 200 mm clamping height and a 120 mm reach provides a pronounced advantage when securing taller workpieces or fixtures. A greater clamping height allows the clamp to engage above bulky components without compromising accessibility, while the extended reach reduces the need for additional adapters. This results in consistent positioning and reduced setup time on the shop floor, improving throughput in milling, drilling and light assembly tasks. Clear rail compatibility reduces mounting uncertainty The specified 28 x 11 mm rail cross-section indicates the exact mounting profile required for secure attachment to standard machine table rails. Knowing this dimension removes guesswork when adapting jigs or t-slotted tables and ensures a mechanically stable interface. The explicit rail specification supports fast integration into existing fixtures and helps maintain repeatable alignment across production runs. Designed for industrial workflows and dependable duty Built by a recognised brand, the clamp emphasises robust mechanical performance and practical handling for daily workshop use. The straightforward geometry enables straightforward clamping actions and reliable locking of components, aiding quick changeovers and minimizing idle time. The result is a clamp that supports a smoother production flow and contributes to measurable efficiency gains in small to medium series work. For specification advice or to secure a BESSEY machine table clamp with 200 mm clamping height, contact Metav Werkzeuge GmbH at info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: 4123740040NW Label: Maschinentischspanner Spann-H.200mm A.120mm Schienenquerschnitt 28x11mm BESSEY Manufacturer: BESSEY Product type: Maschinentischspanner Packaging unit: 1 Core measurements Clamping height: 200 mm Reach / projection: 120 mm Rail cross-section: 28 x 11 mm UID / SKU: 4123740040NW Features and attributes Suitable for machine table mounting Industrial-grade construction Precise rail compatibility 28 x 11 mm Single-unit packaging FAQ What is the maximum clamping height of this clamp? The clamp offers a clamping height of 200 mm, allowing safe engagement above taller workpieces. Which rail profile is required for mounting? Mounting requires a rail with a 28 x 11 mm cross-section, ensuring a secure fit and repeatable alignment. What is the reach or projection of the clamp? The projection is 120 mm, suitable for securing parts positioned away from the rail face. Is this clamp intended for industrial use on machine tables? Yes, the BESSEY machine table clamp is designed for workshop and industrial machine table applications where stable workholding is required. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
200mm Milling Arbor Key DIN 6368 For Arbor Ø22mm, Hardened Special Steel - TECWERK
Combining DIN 6368 conformity with a hardened special steel construction and a 200 mm overall length, this tool delivers reliable access and secure torque for arbor Ø 22 mm applications; ideal for tightening and loosening milling arbor draw-in screws. Order the milling arbor key directly via Metav Werkzeuge or ask our consultants if needed. Milling arbor key DIN 6368 — TECWERK, arbor Ø 22 mm, 200 mm length A milling arbor key DIN 6368 designed for tightening and loosening milling arbor draw-in screws, suited to use with an arbor Ø 22 mm in workshop and production environments. DIN 6368 standard conformity For arbor Ø 22 mm Hardened special steel, tempered finish 200 mm total length for added leverage Precision that matches industry standards The tool is manufactured to DIN 6368, which ensures a precise fit to the clamping interfaces encountered in milling setups. Conformity with this standard reduces the risk of incorrect engagement and slippage, translating into shorter setup times and fewer tool changes. By focussing on measurable compatibility, the design supports repeatable results when working with draw-in screw systems specified to the same norm. Robust construction for consistent torque transfer Constructed from special steel, the key is hardened and tempered to a brown finish, offering a balance of toughness and wear resistance. The treated surface helps the tool withstand repeated use in a busy workshop without rapid loss of function. With a 200 mm overall length the tool provides practical leverage for controlled tightening and loosening of clamping screws while remaining compact enough for confined spindle housings. Designed to simplify workshop routines The geometry of the arbor wrench is optimised for access to milling arbor draw-in screws and related fastening hardware. This focused design reduces handling time and supports efficient machine changeovers, which is important for batch production and maintenance cycles. If compatibility with specific draw-in systems is a concern, technical details in the product data help to confirm fit before purchase. Applications and suitability Intended for use with an arbor of Ø 22 mm, the key is a specialist workshop instrument for milling toolholders and arbors where secure seating of cutters is required. The tool is appropriate for general workshop and industrial environments where standardised clamping elements are in use and where a durable, standard-compliant wrench improves repeatability and safety. For precision work with TECWERK components, request further technical details or secure supply through Metav Werkzeuge — contact Metav Werkzeuge at info@metav-werkzeuge.com or +49 2822 7131930 for fast delivery from Emmerich. Technical data Article number: 4000832439NW SKU: 4000832439NW Product type: Milling arbor key Manufacturer: TECWERK Norm: DIN 6368 Total length: 200 mm Suitable for arbor Ø 22 mm Packaging unit: 1 For tightening and loosening milling arbor draw-in screws Conforms to DIN 6367 where relevant for screw interface Special steel, hardened and tempered to a brown finish FAQ What arbor size is this key suitable for? This milling arbor key is designed for an arbor Ø 22 mm and engages draw-in screw systems specified for that arbor diameter. Which standard does the tool conform to? The tool conforms to DIN 6368, ensuring dimensional compatibility with components and clamping screws produced to the same standard. What is the overall length of the tool? The overall length is 200 mm, providing practical leverage for tightening and loosening clamping screws in workshop and production settings. What material and finish does the key have? The key is made from special steel, hardened and tempered to a brown finish to improve wear resistance and longevity under regular use. Can the key be used with other arbor systems? Compatibility depends on the clamping interface; the key is optimised for systems aligning with DIN 6368 and an arbor Ø 22 mm—verify dimensional match before use. Manufacturer / Responsible: NORDWEST Handel AG, Robert-Schuman-Straße 17, 44263 Dortmund
200mm Pneumatic Precision Machine Vice 9000 kgf Clamping Force, Cast Iron, 0.01mm Accuracy - Vertex
Take advantage of a high‑force, precision workholding solution that combines 9,000 kgf clamping force, 0.01 mm repeatability and robust cast‑iron construction for reliable machining results; order the vice directly via Metav Werkzeuge or consult our specialists for application advice. VMC-8P Pneumatic Precision Machine Vice by Vertex — 9,000 kgf, 0–200 mm opening The VMC-8P is a pneumatically actuated precision machine vice designed for secure, repeatable clamping in milling centres and CNC machining applications 9,000 kgf clamping force Opening range 0–200 mm Cast iron body for high rigidity Accuracy 0.01 mm repeatability Consistent heavy‑duty clamping for demanding machining The vice offers a 9,000 kgf clamping force, delivering stable holding for heavy cutting and interrupted cuts; this reduces micro‑movement, lowers the risk of chatter and contributes to longer tool life. The high clamping force, combined with a precision‑ground jaw interface, translates into measurable improvements in surface finish and dimensional stability. Engineers benefit from a predictable setup that minimises rework and optimises throughput, while production planners gain from a workholding solution that supports repeatable results across serial runs. The emphasis is on dependable, quantifiable performance rather than marketing hyperbole. Pneumatic actuation for rapid, repeatable cycles Pneumatic operation provides fast, uniform closing and opening cycles that integrate smoothly with automated workflows and tool‑change routines. The pneumatic actuation ensures consistent pressure application with minimal manual intervention, which is especially valuable in multi‑fixture setups or lights‑out machining. Repeatability at 0.01 mm level means part repositioning and unclamping do not introduce significant variation, aiding processes that require interchangeability. For process engineers, the combination of speed and repeatability equates to reduced cycle times and improved overall equipment effectiveness. Rigid construction and compact footprint for stable setups Constructed from cast iron, the vice body offers inherent damping and rigidity that counteracts cutting forces and helps maintain clamping integrity. With a compact footprint of 200 x 610 x 173 mm and a mass of 74 kg, the unit provides a stable base without occupying excessive table area, making it suitable for both single‑station fixtures and multi‑vice configurations. The 0–200 mm opening range covers a broad spectrum of component sizes, while the robust build supports continuous shop‑floor use with minimal maintenance. The design focus is longevity and precision retention under regular production loads. For tailored application advice or to request supply of the Vertex VMC-8P via Metav Werkzeuge, contact our team in Emmerich at info@metav-werkzeuge.com or call +49 2822 7131930 for prompt, specialist support and reliable delivery Technical data SKU: VMC-8P GTIN: 4061905091933 Brand: Vertex ECLASS: 21020601 ETIM: EC002173 Key figures Opening range: 0–200 mm Clamping force: 9,000 kgf Accuracy: 0.01 mm Weight: 74 kg Dimensions: 200 x 610 x 173 mm Materials & features Material: cast iron Actuation: pneumatic Type: Pneumatic precision machine vice SKU: VMC-8P FAQ What clamping force does the vice provide? The vice delivers a clamping force of 9,000 kgf, which ensures secure holding during heavy milling; this specification refers to the Vertex VMC-8P pneumatic machine vice. What is the usable jaw opening of the unit? The VMC-8P offers an opening range of 0–200 mm, allowing accommodation of a wide variety of component sizes in standard machining setups. How precise is the positioning and repeatability? Repeatability is specified at 0.01 mm, providing the precision required for serial production and tight‑tolerance machining with the Vertex VMC-8P. What is the construction material and why does it matter? The body is made from cast iron, chosen for its rigidity and vibration damping; this improves clamping stability and contributes to consistent machining results with the VMC-8P. Is the vice suitable for integration with CNC workflows? Yes; pneumatic actuation and compact dimensions make the vice suitable for CNC integration, enabling fast, repeatable cycles and straightforward fixture design with the VMC-8P. Manufacturer: Vertex Machinery Works Co., Ltd.; No. 296, Sec. 1, Feng Shih Road, Fengyuan District, Taichung City 420, Taiwan
200mm Precision Parallel Set 8pcs Including V-Blocks, 0.01mm Accuracy - Vertex
Take advantage of precise alignment and a matched, workshop-ready kit for consistent setups and reduced rework. The combination of 0.01 mm accuracy, standard 200 mm lengths and robust, matched parallels ensures reliable clamping and repeatability across milling and inspection tasks. Order the Precision Parallel Block Set VP-033 directly via Metav Werkzeuge or consult our specialists for configuration advice. Precision Parallel Block Set VP-033 by Vertex — 0.01 mm accuracy, 200 mm parallels A Precision Parallel Block Set VP-033 designed for reliable workpiece levelling and clamping in milling, drilling and inspection applications across toolrooms and general workshops. *High accuracy 0.01 mm *Long 200 mm parallels for stable support *Matched set with clamping brackets Consistent alignment for precision machining Precision on the machine bed begins with consistent support. The set delivers 0.01 mm tolerance across its parallels, providing a measurable reduction in setup variation and minimising rework. Each parallel is produced for even contact and flatness, translating directly into improved surface finish and dimensional stability during cutting or inspection. Described tolerance values allow straightforward process planning and easier verification against inspection criteria, making the set suitable where reproducible results are required. Matched components for repeatable setups The kit comprises parallels in several widths with a uniform length of 200 mm, together with matching clamping brackets to form stable reference points for vice and fixture work. This matched configuration removes guesswork during setup, shortens machine downtime between jobs and supports modular fixturing concepts. The construction supports routine shop use and aligns with systematic workflow approaches, offering practical benefits for batch production and prototype runs where repeatability is essential. Practical integration and trusted origin Designed for straightforward adoption on the shop floor, the parallels are compatible with common vices, fixture systems and inspection benches, enabling fast integration into existing processes. Sourced from Vertex, the set benefits from established manufacturing standards and quality control that support dependable performance. The design emphasises functional utility and reduces handling complexity, which helps maintain throughput while safeguarding measurement integrity in everyday use. Contact Metav Werkzeuge in Emmerich to request tailored advice, check availability of Vertex accessories and secure the VP-033 precision parallel block set for immediate integration into production. Technical Data Article number: VP-033 GTIN: 4061905089015 Manufacturer: Vertex Core data Dimensions (packaging): 340 x 223 x 85 mm Accuracy: 0.01 mm Weight: 6.4 kg Pieces per set: 8 Contents / Special features Contents: precision parallels in various widths, all 200 mm length, plus clamping brackets Set: matched components for repeatable setups Brand: Vertex FAQ What accuracy can be expected when using this parallel set? The VP-033 precision parallel block set from Vertex is specified with an accuracy of 0.01 mm, ensuring reliable reference surfaces for machining and inspection. Which applications are suitable for these parallels? These parallels are intended for workpiece levelling and support in milling, drilling and inspection operations, providing consistent alignment for both production and toolroom tasks. Are the parallels compatible with standard vices and fixtures? Yes. The design of the parallels and included clamping brackets allows straightforward use with common vices and fixture systems on the shop floor. How does the matched set improve setup times? Matched parallels and brackets eliminate the need for individual matching and adjustment during each setup, reducing changeover time and increasing repeatability between jobs. Is this a complete kit for basic parallel support? The VP-033 set contains a range of widths in a uniform 200 mm length and includes clamping brackets, providing a practical kit for typical support and levelling tasks. Manufacturer: Vertex Machinery Works Co., Ltd.; No. 296, Sec. 1, Feng Shih Road, Fengyuan District, Taichung City 420, Taiwan
200mm Reversible Self-Centring Three-Jaw Chuck, 109mm Height, 3xM12 Thread - Vertex
High-repeatability clamping is achieved by the self-centring three-jaw mechanism combined with a 200 mm nominal diameter and a sturdy 16 kg mass, ensuring stable machining and reduced setup time. Order the VSK-8A chuck directly via Metav Werkzeuge or ask our consultants if needed. VSK-8A 3-jaw self-centring reversible chuck, 200 mm — Vertex The VSK-8A is a three-jaw, self-centring and reversible chuck engineered for secure workholding in turning and medium- to heavy-duty lathe operations. Self-centring three-jaw mechanism Reversible operation for internal and external clamping 200 mm nominal diameter for larger workpieces Robust 16 kg mass for increased stability Consistent concentricity for predictable results A self-centring three-jaw design synchronises the jaw movement so that round and indexed parts are clamped to the same centre every cycle, reducing repositioning and inspection time. This concentric clamping principle leads to improved repeatability on batch runs and fewer scrapped parts. The 200 mm nominal diameter expands the usable clamping envelope, permitting larger diameters to be held without additional adapters. For users unfamiliar with the term, self-centring means the jaws move simultaneously, aligning the workpiece to the chuck axis automatically, which simplifies setup and lowers operator dependency. Versatile clamping to reduce tooling complexity A reversible chuck enables both external gripping and internal chucking without swapping the primary workholding system, which shortens changeover intervals and reduces the number of separate fixtures required in the tooling cabinet. The design described as reversible supports internal holding of hollow components as well as robust external jaws for solid stock. The provided 3xM12 mounting thread ensures a secure connection to a lathe spindle or backplate, maintaining the required rigidity during higher cutting loads. This capability translates directly into fewer interruptions and a more efficient production flow. Mass and dimensions that improve surface finish and rigidity The chuck’s 16 kg mass contributes inertia that dampens vibration during cutting, which in turn helps to improve surface finish and tool life on demanding operations. A height of 109 mm provides a compact yet rigid profile that integrates easily with many lathe configurations while maintaining access for tooling and measurement. Together, the mass and dimensions support stable holding under variable axial and radial forces, making the unit suitable where consistent clamp stability matters. The overall build quality is aimed at industrial use where robustness and repeatable performance are valued. For robust, repeatable workholding with Vertex quality, contact Metav Werkzeuge in Emmerich for tailored procurement and technical consultation — email info@metav-werkzeuge.com or call +49 2822 7131930 Technical Data SKU: VSK-8A GTIN: 4061905089732 Manufacturer: Vertex Facts Diameter: 200 mm Height: 109 mm Weight: 16 kg Mounting thread: 3xM12 eClass: 21020590 Special features Three-jaw, self-centring and reversible chuck Reversible function for internal and external clamping Designed for lathe workholding applications Brand: Vertex FAQ What nominal diameter does the chuck support? The chuck supports a nominal diameter of 200 mm, suitable for larger turned components and extended clamping envelopes. Can the chuck be used for internal clamping? Yes, the reversible design permits internal clamping as well as external gripping, allowing flexible use without multiple chucks. How is the chuck mounted to a spindle or backplate? Mounting is via the provided 3xM12 thread configuration; secure attachment ensures rigidity under cutting loads. Does the chuck provide improved vibration damping? The substantial mass of 16 kg increases inertia and contributes to vibration damping, which can enhance surface finish and tool life. What does self-centring mean in practical terms? Self-centring means the jaws move simultaneously to align the workpiece automatically to the chuck axis, reducing setup steps and improving repeatability. Manufacturer: Vertex Machinery Works Co., Ltd.; No. 296, Sec. 1, Feng Shih Road, Fengyuan District, Taichung City 420, Taiwan
200mm Rotary Indexing Table Simple With Three-Point 10" Readout, 4° Per Spindle Turn, 318x209x274mm - Vertex
Taking advantage of a compact footprint, robust mass and precise indexing, this device ensures reproducible angular positioning for milling and drilling tasks; its 200 mm diameter, 58 mm centre bore and included 3‑jaw chuck deliver reliable set‑ups. Order the rotary table directly via Metav Werkzeuge or consult our specialists for application advice. CC-8 rotary table by Vertex — 200 mm diameter, 58 mm centre bore The CC-8 rotary table is a simple, precision indexing table designed for accurate workpiece rotation in milling, drilling and light production tasks. 200 mm precision rotary table 58 mm centre bore for direct mounting 4° indexing per spindle revolution Includes 3‑jaw chuck and cover plates Solid 51.5 kg construction Precise indexing for repeatable machining results The rotary indexing head offers 4° indexing per spindle revolution and a reading resolution of 10", enabling controlled angular steps without auxiliary electronics. With a 200 mm diameter platen and a 58 mm centre bore, the device supports direct mounting of chucks and fixtures, reducing set‑up time and minimising clamping errors. The mechanical indexing mechanism converts spindle turns into exact angular displacements, which is particularly advantageous when executing circular drilling patterns or dividing workpieces for fixture operations; the robust mass contributes to vibration damping during cuts, improving surface finish and tool life. Versatile integration into workshop workflows Designed as a straightforward rotary table for general workshop and small production environments, the unit adapts to conventional milling machines and drill presses. The simple design and included 3‑jaw chuck and a set of cover plates (2, 3, 4, 6, 8, 12) make it possible to change configurations quickly and maintain process continuity. This versatility supports lean workflows: fewer tool changes, reduced downtime and consistent positioning for repeat batches. The compact overall dimensions and standard mounting provisions ease retrofitting to existing machine tables, offering operational benefits without the need for complex interfaces. Built for durability and dependable operation Constructed with substantial mass — 51.5 kg — and compact external dimensions of 318 x 209 x 274 mm, the unit provides a stable platform for cutting operations. The solid build resists deflection under moderate clamping forces and contributes to consistent results across repeated cycles. Included accessories allow immediate use on delivery, so the table becomes a functional part of production straight away. The combination of weight, mechanical simplicity and a clear centre bore supports long service intervals and straightforward maintenance routines, which is valuable for workshops seeking reliable equipment without elaborate servicing demands. Practical handling and setup explained Setup involves fixing the table to the machine table, aligning the centre bore to the spindle axis and securing the workpiece with the supplied chuck or faceplates. The 58 mm centre bore enables direct fitting of most common chucks and arbors, reducing the need for additional adaptors. The readable indexing scale and the defined 4° per spindle turn conversion facilitate quick calculation of division angles for common divisors; for finer divisions, successive increments with the spindle deliver the desired step. Where repeatability is required, the mechanical indexing ensures the same angular position is achieved without reliance on electronic systems. For technical guidance or application recommendations for the Vertex CC-8 rotary table, contact Metav Werkzeuge — our Emmerich‑based team will advise on suitability and delivery directly from stock via info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: CC-8 GTIN: 4061905086977 Manufacturer: Vertex Eclass: 36600610 Name: Rundteiltisch (simple) Facts Diameter: 200 mm Dimensions: 318 x 209 x 274 mm Weight: 51.5 kg Centre bore: 58 mm Indexing per spindle revolution: 4° Reading resolution: 10" Special features Contents: 1x 3‑jaw chuck, cover plates 2, 3, 4, 6, 8, 12 Simple design SKU: CC-8 FAQ What is the effective table diameter? The table offers a 200 mm diameter platen suitable for a wide range of small to medium workpieces on the Vertex CC-8 rotary table. Can the unit be mounted directly to a milling machine? Yes. The CC-8 rotary table has a standard mounting footprint and a 58 mm centre bore for direct mounting of chucks and arbors. How precise is the angular indexing? Indexing is provided at 4° per spindle revolution with a reading resolution of 10", enabling controlled and repeatable angular steps for common dividing tasks. What accessories are supplied with the table? Delivery includes a 3‑jaw chuck and cover plates in sizes 2, 3, 4, 6, 8 and 12, allowing immediate clamping options without extra purchases. Is the table suitable for heavy cutting operations? The device has a solid mass of 51.5 kg and a compact design that dampens vibration; it is intended for milling and drilling operations where moderate clamping and cutting forces are applied. Manufacturer: Vertex Machinery Works Co., Ltd.; No. 296, Sec. 1, Feng Shih Road, Fengyuan District, Taichung City 420, Taiwan
200mm Round Magnetic Chuck 78mm Height, 12.8kg - Vertex
Benefit from compact, consistent clamping with the 200 mm round magnetic chuck: its low-profile 78 mm height and 12.8 kg robust mass deliver stable, vibration-reducing workholding for precision machining. Order the unit directly via Metav Werkzeuge or consult our technical advisors for application guidance. Magnetic chuck VGD-08 — Round magnetic clamping plate, 200 mm diameter, Vertex A magnetic chuck VGD-08 designed for secure workpiece clamping across general machining applications, offering a compact footprint and stable holding force for accurate processing. 200 mm round diameter 78 mm compact height 12.8 kg robust construction Precision magnetic clamping Space-saving profile that steadies the machining process The round clamping plate's 200 mm diameter combined with a low profile of 78 mm reduces the distance between the workpiece and the machine spindle, improving stiffness and axis control during turning or light milling operations. The compact design limits overhang and supports better surface finish by lowering vibration transmission. The stable 12.8 kg mass contributes to dynamic damping, which is particularly relevant when short-cycle precision and repeatability are required on small to medium-sized components. Predictable magnetic hold for reliable set-ups Magnetic clamping provides a repeatable holding method without mechanical jaws, enabling quicker set-ups for flat and suitably shaped workpieces. The unit delivers a consistent magnetic clamping action, easing fixture changes and reducing overall set-up time. For operators with limited metrology expertise, the principle is straightforward: an even magnetic field equals uniform holding force across the work area, which supports precision machining and predictable tool wear. The robust construction ensures the magnetic properties remain stable under typical workshop conditions. Built for integration and workshop efficiency The round form factor suits rotary tables and smaller machine beds, allowing efficient fixturing of discs, rings and plate-like parts. Manufactured under the Vertex designation and supplied as SKU VGD-08, the clamping plate fits into established workflows where repeatability and uncomplicated handling are priorities. Its uncomplicated geometry simplifies cleaning and maintenance routines and reduces downstream inspection deviations, supporting smoother production runs and fewer reworks. Contact Metav Werkzeuge for tailored advice on integrating the Vertex VGD-08 magnetic chuck into existing setups and to arrange swift dispatch from our Emmerich stock Technical data SKU: VGD-08 GTIN: 4061905086106 EClass: 21020809 Core technical data Diameter: 200 mm Height: 78 mm Weight: 12.8 kg Features Round design Magnetic clamping function Brand: Vertex Suitable for general machining clamping applications FAQ What is the diameter of the clamping surface? The clamping surface has a diameter of 200 mm on the Vertex magnetic chuck (VGD-08). How high is the unit and why does that matter? Height is 78 mm; the low profile reduces overhang and improves stiffness for more stable machining. What is the weight of the product and its benefit? The unit weighs 12.8 kg; the mass helps damp vibration and increases dynamic stability during processing. Can the chuck be used on rotary tables and small machine beds? Yes, the round form and compact height of the VGD-08 make it suitable for rotary tables and smaller machine beds in precision workshops. Is this product identified by a specific SKU? Yes, the chuck is supplied under SKU VGD-08 and carries GTIN 4061905086106 for traceability. Manufacturer: Vertex Machinery Works Co., Ltd.; No. 296, Sec. 1, Feng Shih Road, Fengyuan District, Taichung City 420, Taiwan
200mm Simple Steady Rest With Three- or Four-Jaw Chuck, 1° Graduation - Vertex
Take advantage of the combination of precise indexing, robust construction and simple clamping options for dependable workshop production. Order the VSR-8 dividing head directly via Metav Werkzeuge or ask our consultants if needed. VSR-8 simple dividing head — 200 mm diameter, 1° scale (Vertex) VSR-8 is a compact simple dividing head designed for accurate indexing with an integrated three- or four-jaw chuck for versatile clamping Precision 1° indexing scale 200 mm body diameter Includes three- or four-jaw chuck Solid construction, 27 kg mass Exact indexing for repeatable machining The VSR-8 dividing head provides precise 1° graduations, enabling exact angular positioning for repetitive operations. The clear graduation reduces setup time and minimises indexing errors, which helps to improve throughput and reduce scrap. The combination of readable scale and rigid spindle results in consistent angular repeatability, making the device suitable where reliable division of workpieces is required. Stable support for consistent cuts Engineered with a substantial mass, the unit's robust construction delivers stability under load and resists vibration during machining. This solidity improves surface finish and cutter engagement consistency, translating directly into fewer reworks and longer tool life. The durable build also supports steady clamping forces, which contributes to safer, more predictable results in precision tasks. Flexible clamping for varied workpieces Supplied with a three- or four-jaw chuck, the dividing head accommodates a wide range of workpiece geometries without elaborate fixturing. The chuck options allow quick adaptation between irregular and concentric parts, reducing downtime during job changes. Integration into existing fixtures is straightforward thanks to the standard mounting interfaces and conservative dimensions, so installation does not require major alterations to workshop workflows. For precision indexing and reliable workshop performance, contact Metav Werkzeuge in Emmerich to discuss the Vertex VSR-8 dividing head and arrange supply or technical advice. Technical data SKU: VSR-8 GTIN: 4061905089381 Manufacturer: Vertex Key measurements Body diameter: 200 mm Height: 159 mm Mass: 27 kg Scale division: 1° Features Simple dividing head design Delivered with three- or four-jaw chuck Compact footprint FAQ What indexing resolution does the unit provide? The VSR-8 dividing head offers a 1° graduation on the scale for precise angular indexing. Which chuck configuration is supplied with the VSR-8? The VSR-8 is supplied with a three- or four-jaw chuck, allowing clamping of both irregular and concentric components. What are the main dimensions and weight of the dividing head? The VSR-8 has a body diameter of 200 mm, a height of 159 mm and a mass of 27 kg. Is the VSR-8 appropriate for repeated indexing tasks in a small workshop? Yes, the VSR-8 dividing head is designed for reliable, repeatable indexing in workshop environments where compact, accurate division is required. Who manufactures the VSR-8 and where is it made? The VSR-8 is produced by Vertex; the product is listed under the Vertex brand and supplied with the manufacturer's identification. Manufacturer: Vertex Machinery Works Co., Ltd.; No. 296, Sec. 1, Feng Shih Road, Fengyuan District, Taichung City 420, Taiwan
200mm Simple Tailstock With Three- or Four-Jaw Chuck 1° Reading - Vertex
Take advantage of the combination of precise 1° indexing, a 200 mm chuck diameter and robust mass for stable machining. The compact construction supports a wide range of rotary machining tasks while keeping set-up straightforward. Order the VSR-83 dividing head directly via Metav Werkzeuge or ask our consultants if needed. VSR-83 dividing head (simple indexing unit) with 200 mm chuck and 1° indexing The VSR-83 dividing head is a compact, workshop-ready indexing unit designed to provide reliable division and rotary positioning for milling and similar rotary operations, equipped for use with three- or four-jaw chucks. 200 mm chuck diameter for larger workpieces 1° indexing accuracy for precise division Accepts three- or four-jaw chucks for flexibility Solid 30.5 kg mass for vibration damping Precise division for repeatable machining results The compact dividing head provides mechanical 1° indexing, enabling repeatable angular steps for tasks such as slotting, gear blank indexing and multi‑face machining. The clear specification of 1° readout means divisions are predictable and verifiable, which reduces set-up iterations. For users less familiar with indexing devices: an indexing head translates rotary motion into defined angular positions, so operations that require equally spaced features are carried out consistently and with reduced fixturing complexity. This focus on repeatability supports process stability and consistent part quality. Flexible clamping to match varied workshop needs Compatibility with three- or four-jaw chucks allows the unit to handle a broad spectrum of workpiece shapes. A three-jaw chuck typically suits round, self‑centring stock where fast clamping is required, while a four-jaw chuck gives independent adjustment for irregular or off‑centre components. The 200 mm chuck diameter increases the usable clamping envelope, enabling larger diameters to be held without additional adapters. The result is a single, adaptable rotary device that reduces the need for multiple dedicated fixtures. Mass and geometry that improve machining stability A unit mass of 30.5 kg provides inherent damping against cutting vibrations, which contributes to improved surface finish and longer tool life in cutting operations. The overall height of 159 mm keeps the centre of rotation relatively low, simplifying alignment on common machine tables and rotary fixtures. Together, mass and compact geometry support stable cutting conditions: heavier, well-balanced fixturing diminishes chatter and helps maintain dimensional accuracy under load. Straightforward integration and trusted manufacture The simple mechanical concept of this indexing unit supports straightforward integration into standard workshop setups. The product is manufactured by Vertex, a recognised name in machine accessories, and is supplied under SKU VSR-83. Its uncomplicated construction favours durability and predictable behaviour in continuous shop use, making it a practical component for toolrooms and light industrial machining operations that require consistent angular positioning without complex electronics. Contact Metav Werkzeuge for tailored application advice and to arrange supply of the Vertex VSR-83 dividing head — email info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: VSR-83 GTIN: 4061905089930 eClass: 21020590 Core specifications Chuck diameter: 200 mm Height: 159 mm Readout resolution: 1° Weight: 30.5 kg Features Three- or four-jaw chuck compatible Simple dividing head / indexing unit Manufacturer: Vertex FAQ What angular resolution does the unit provide? The VSR-83 dividing head offers a mechanical 1° indexing resolution, allowing for repeatable angular divisions in milling and rotary machining. Which chuck types can be fitted to the unit? The unit is compatible with three- or four-jaw chucks, enabling both rapid, self‑centring clamping and independent‑jaw set‑up for irregular shapes. How does the weight affect machining performance? A mass of 30.5 kg increases damping of cutting vibrations; this contributes to improved surface finish and greater dimensional stability during machining. For which tasks is this indexing head most suitable? The indexing head is suited to operations requiring precise angular positioning such as slotting, drilling pattern division and simple gear blank indexing in workshop and toolroom environments. What are the mounting considerations for the device? The unit’s overall height of 159 mm should be considered during set-up to ensure correct alignment with the machine table or fixture; an appropriate mounting fixture or adapter is recommended for secure installation. Manufacturer: Vertex Machinery Works Co., Ltd.; No. 296, Sec. 1, Feng Shih Road, Fengyuan District, Taichung City 420, Taiwan
200mm Stud Bolt DIN 6379 M16 Heat Treated 8.8 - AMF
Robust fastenings meet consistent quality: the stud bolt combines DIN 6379 compliance with heat treatment to property class 8.8, and a standard M16 thread at 200 mm overall length to deliver reliable tensile performance and repeatable assembly results. Order the item directly via Metav Werkzeuge or consult Metav's advisers for supply and batch planning. AMF stud bolt DIN 6379 — M16 x 200 mm, quenched and tempered to 8.8 A AMF stud bolt DIN 6379 M16 x 200 mm, designed for secure mechanical assemblies where standardised dimensions and elevated strength are required. DIN 6379 standardised design Heat-treated to property class 8.8 M16 thread for standard assemblies 200 mm overall length Consistent mechanical performance for standard assemblies The stud bolt is made to the DIN 6379 specification and offers a predictable geometry for flange and coupling connections. The combination of a standard M16 thread and 200 mm overall length enables straightforward integration into established fastening concepts, reducing set-up time and ensuring interchangeability. The component's repeatable dimensions support process stability in production and maintenance tasks, providing measurable benefits for mechanical consistency and assembly efficiency. Heat treatment and what property class 8.8 delivers Heat treatment described as quenched and tempered results in the declared property class 8.8, which balances tensile strength with ductility for dependable load-bearing behaviour. This treatment increases resistance to static and dynamic stresses compared with untreated fasteners while maintaining machinability for final adjustments. The result is a robust fastener suitable for applications demanding elevated mechanical reliability without resorting to specialised high-alloy solutions. Practical handling and installation advantages in the workshop With a nominal width 19 mm and a standard metric thread, the stud allows use with common wrenches, nuts and washers, simplifying tooling and inventory requirements. The product's standardisation reduces the need for special components and supports efficient replenishment cycles from central stock. Where traceability is required, the item can be referenced by its article number for quality records and procurement planning, contributing to streamlined workshop logistics and reduced downtime. Discuss batch supply and technical options for the AMF stud bolt with Metav Werkzeuge’s specialists in Emmerich — contact info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: 4000833276NW Manufacturer: AMF Product type: Stud bolt Standard: DIN 6379 Label: Stiftschraube DIN6379 M16x200mm vergütet auf 8.8 AMF Core measurements Thread: M16 Overall length: 200 mm Width: 19 mm Packaging unit: 1 Special features Heat treatment: quenched and tempered to property class 8.8 Standard compliance: DIN 6379 Axite enrichment: Addition: b: 122 FAQ What standard does this stud bolt conform to? The item conforms to DIN 6379, ensuring standardised dimensions and fit for typical mechanical and structural connections. Which thread and length are specified for the fastener? The fastener is supplied as an M16 thread with a 200 mm overall length, matching conventional metric assembly requirements. What does property class 8.8 indicate for this fastener? Property class 8.8 denotes that the stud bolt has undergone heat treatment (quenched and tempered) to provide enhanced tensile performance and reliable load-bearing characteristics. Is the stud suitable for standard workshop tooling? Yes; the nominal width 19 mm and metric thread make the component compatible with commonly available wrenches, nuts and washers. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
200mm Stud Bolt M20x200 Quenched Grade 8.8, DIN 6379 - AMF
Take advantage of a high‑strength stud bolt that meets DIN 6379, with an M20 thread and an overall length of 200 mm, for dependable mechanical fastening; order the part directly via Metav Werkzeuge or consult the technical team for application advice. AMF Stiftschraube DIN 6379 – Stud bolt M20 x 200 mm, property class 8.8 The AMF Stiftschraube DIN6379 M20x200mm is a heat‑treated stud bolt designed for secure fastening in industrial and workshop assemblies. DIN 6379 conforming stud bolt Heat-treated to property class 8.8 Thread M20 for standard fittings Overall length 200 mm Reliable fastening for demanding assemblies A stud bolt manufactured to an established metric standard delivers consistent clamping and repeatable performance. The compliance with DIN 6379 ensures dimensional accuracy and interchangeability with standard nuts and threaded components, reducing assembly time and the risk of mismatched parts. Specifying a stud with defined mechanical properties supports predictable joint behaviour under load, which in turn helps to minimise unscheduled downtime and keeps production flows steady. Clear specification for confident selection Key specification data such as M20 thread and 200 mm overall length make selection straightforward when matching to flanges, housings or repair parts in mechanical systems. The marking of property class 8.8 indicates that the fastener has been heat‑treated to provide elevated strength compared with standard grade fasteners; this attribute is important when higher clamping forces or fatigue resistance are required. Where necessary, refer to the relevant engineering tables or DIN documentation for pitch and torque guidance to ensure secure installation. Practical fit and installation guidance for workshop use For routine workshop and industrial use, this stud bolt works well in assemblies that demand a robust metric connection and consistent geometry. When installing, ensure correct thread engagement and use appropriate locking measures to maintain joint integrity over time. The product’s standardised dimensions facilitate inventory management and simplify maintenance planning, enabling rapid replacement during service operations and supporting efficient workshop workflows. For specification confirmation or application support for the AMF stud bolt, contact Metav Werkzeuge’s technical advisors in Emmerich at info@metav-werkzeuge.com or by phone at +49 2822 7131930. Technical data Article number: 4000833285NW Manufacturer: AMF Product type: Stud bolt Standard: DIN 6379 Facts Thread: M20 Overall length: 200 mm Width: 27 mm Special features Heat-treated to property class 8.8 Packaging unit: 1 Label: Stiftschraube DIN6379 M20x200mm vergütet auf 8.8 AMF Axite enrichment: Addition: b: 122 FAQ What standard does this stud bolt conform to? The stud bolt is manufactured to DIN 6379, as stated on the product label for reliable dimensional and thread conformity. What do the markings ‘M20’ and ‘200 mm’ mean for selection? They denote a metric M20 thread and an overall length of 200 mm, which define compatibility with standard nuts and mounting depths for mechanical assemblies. What does property class 8.8 indicate about strength? Property class 8.8 describes the heat‑treated condition and mechanical strength level of the fastener, signifying higher tensile and yield performance compared with lower classes. How is the item identified for ordering? Order using the SKU 4000833285NW and refer to the product label description to ensure the correct AMF stud bolt is supplied. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
200mm Stud Bolt M24x200 Heat-Treated Grade 8.8, DIN 6379 - AMF
Take advantage of a standardised fastener that combines DIN 6379 conformity, a robust M24 thread and quenched and tempered 8.8 material properties for secure, repeatable assembly performance. Order the AMF stud bolt directly via Metav Werkzeuge or ask our consultants if additional data is required. AMF stud bolt DIN 6379, M24 x 200 mm, property class 8.8 A AMF stud bolt DIN 6379 M24 x 200 mm designed for reliable mechanical fastening in industrial assembly, maintenance and plant construction applications. DIN 6379 compliant Thread dimension M24 Overall length 200 mm Tempered to property class 8.8 Consistent clamping and industrial interchangeability The stud bolt is manufactured to DIN 6379, ensuring consistent dimensional accuracy and interchangeability in production and repair environments. Compliance with this standard simplifies procurement and assembly planning by aligning with widely accepted metric fastening specifications. The component’s quenched and tempered 8.8 designation indicates a medium-high strength class, delivering dependable clamp load for structural joints while maintaining good toughness for general industrial use. Precise thread and length for deep-installation tasks Equipped with a coarse M24 thread and an overall length of 200 mm, the fastener suits deeper thread engagements and multi-layer joints. The supplied data also indicates a thread length b: 122 mm, which supports extended engagement where longer threaded overlap is required. Accurate thread form and size mean predictable torque-to-tension behaviour and easier selection of appropriate nuts and washers, reducing rework and improving assembly efficiency. Application scope, handling and quality assurance This stud bolt is aimed at plant builders, maintenance technicians and mechanical assemblers who require a standardised, heat-treated fastener for robust connections. Supplied as a single unit, the part is ready for immediate installation and is appropriate for structural and equipment fastening where an 8.8 property class is specified. For any uncertainty about fitment or compatibility with a specific machine or construction detail, Metav Werkzeuge’s technical advisers can provide comparative data and guidance to ensure the correct choice for each application. For supply and technical advice on AMF stud bolts, contact Metav Werkzeuge in Emmerich — request application guidance or delivery information by email at info@metav-werkzeuge.com or by phone on +49 2822 7131930 Technical data Article number: 4000833297NW SKU: 4000833297NW Product type: Stud bolt (Stiftschraube) Standard: DIN 6379 Label: Stiftschraube DIN6379 M24x200mm vergütet auf 8.8 AMF Facts Thread: M24 Overall length: 200 mm Width: 35 mm Thread length b: 122 mm Packaging unit: 1 Special features Quenched and tempered to property class 8.8 Metric coarse thread for mechanical assemblies Suitable for standard industrial fastening tasks FAQ What standard does this stud bolt comply with? The stud bolt is manufactured to DIN 6379, which defines the dimensional and thread characteristics for this type of metric stud. What are the key dimensions of the fastener? Key dimensions include M24 thread, 200 mm overall length and a thread length b: 122 mm, as specified for this item. What does property class 8.8 mean for application? Property class 8.8 indicates a quenched and tempered fastener with medium-high tensile strength, suitable for many structural and machinery connections where a reliable clamp force is required. Is the stud bolt supplied individually or in bulk? This item is supplied in a packaging unit of 1, ready for immediate installation. Can this fastener be used in structural steel assemblies? Yes, the combination of DIN 6379 conformity and 8.8 heat treatment makes the fastener appropriate for standard structural and equipment fastening, subject to project-specific specifications. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
200mm T-Slot Bolt M16 With Nut And Washer, DIN 787 - AMF
Take advantage of a robust, DIN‑compliant clamping solution that combines Grade 8.8 strength with an M16 thread and a 200 mm overall length for secure fixture retention in 18 mm T‑slots; order the assembly through Metav Werkzeuge or contact our specialists for compatibility advice. AMF T-slot bolt DIN 787 — M16 x 200 mm for 18 mm T-slot, Grade 8.8 A T-slot bolt by AMF for use in 18 mm machine table T‑slots, supplied complete with nut and washer for reliable clamping and straightforward installation DIN 787 compliant design Grade 8.8 high-tensile steel Fits 18 mm T-slots Supplied with nut and washer M16 thread, 200 mm overall length Reliable clamping performance for fixtures and tooling The DIN‑specified design ensures a predictable mechanical interface: compatibility with DIN 787 means the bolt aligns with common machine table tolerances and fixture systems, while the M16 thread gives a secure threaded engagement for standard clamping hardware. Manufactured to a Grade 8.8 classification, the connector offers a balance of tensile strength and ductility suitable for general workshop and industrial jigs, reducing the risk of slippage under load and supporting consistent setup repeatability. Precise fit and clear dimensional data for selection Detailed dimensional information supports quick selection and reduces trial‑and‑error. The assembly is intended for an 18 mm T‑slot and includes clear axial enrichment values (A: 17.7 mm; B: 125 mm; E: 28 mm; K: 10 mm) to confirm head and engagement geometry against existing fixtures. Supplied as a complete set with nut and washer, the component removes the need to source mating parts separately and simplifies inventory management on the shop floor, enabling faster cycle times during clamping operations. Built for workshop durability and dependable supply Engineered for repeated use in demanding environments, the bolt’s specification supports routine machining and fixturing tasks while offering long‑term serviceability. The combination of a standardised norm, robust thread form and included mounting hardware provides practical advantages: reduced setup time, lower risk of incompatible parts and predictable replacement intervals. Sourced via Metav Werkzeuge, the product benefits from an established European supply chain and quality control practices that help maintain a reliable parts stream for production and maintenance teams. For secure, DIN‑compliant clamping solutions, request a supply consultation from Metav Werkzeuge to confirm fit and delivery for the AMF T‑slot bolt (SKU 4000833341NW) and ensure seamless integration with existing machine tables Technical data SKU: 4000833341NW Label: T‑Nutenschraube DIN 787 T‑Nut 18mm M16 L.200mm Güte 8.8 m.Mutter u.Scheibe AMF Product type: T‑slot bolt Brand: AMF Norm: DIN 787 Dimensions & core data Thread: M16 Overall length: 200 mm T‑slot width: 18 mm Axial additions: A: 17.7 mm; B: 125 mm; E: 28 mm; K: 10 mm Packaging unit: 1 Special features Grade 8.8 high‑tensile classification Supplied with nut and washer Axial enrichment values included Suitable for standard machine T‑slots FAQ Is this bolt suitable for standard 18 mm machine table T‑slots? Yes. The AMF T‑slot bolt is designed specifically for an 18 mm T‑slot and conforms to DIN 787 to match common machine table specifications. What does Grade 8.8 indicate for this fastening element? Grade 8.8 denotes a high‑tensile steel classification that balances strength and ductility, offering dependable clamping performance for fixtures and general workshop applications. Does the delivery include all required fixing parts? The product is supplied complete with nut and washer as indicated in the product description, simplifying installation and spare‑part management. What are the axial enrichment values and why do they matter? The axial enrichment values (A: 17.7 mm; B: 125 mm; E: 28 mm; K: 10 mm) define head and engagement geometry; these dimensions aid in confirming clearance, head seating and thread engagement with existing fixtures. Is the bolt compatible with metric M16 clamping accessories? Yes, the M16 thread is a standard metric size and is compatible with typical M16 nuts and clamping accessories used in workshop fixturing. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
200mm T-Slot Bolt M24 28mm T-Slot, Grade 8.8 DIN 787 - AMF
Take advantage of the standardised design and high tensile property class to ensure reliable clamping in machine tables; the combination of DIN 787 compliance and an M24 thread provides straightforward interchangeability and robustness — order directly via Metav Werkzeuge or consult the technical team for application advice. T-slot screw DIN 787 – 28 mm T-slot, M24 thread (AMF) The T-slot screw DIN 787 is a high-strength fastening solution for 28 mm T-slots, intended for machine tables, fixtures and heavy-duty clamping applications. DIN 787 standardised design Fits 28 mm T-slots M24 metric thread Grade 8.8 strength, 200 mm length Reliable standard conformity for seamless integration Compliance with DIN 787 ensures predictable dimensions and compatibility with industry-standard T-slot systems, which simplifies machine set-up and interchange of clamping elements. The standardised profile reduces measurement and fitting time during fixture changes and supports consistency across multiple workstations. As a result, downtime is minimised and procurement becomes more efficient, since replacement parts conform to an established European norm. High-strength performance and secure clamping The Grade 8.8 property class and the M24 metric thread deliver a robust combination of tensile strength and reliable torque transmission, suitable for heavy clamping forces on machine tables and modular fixturing. With a 200 mm overall length the fastener allows deeper engagement where extended bite is required. The coarse M24 thread supports strong preload while remaining serviceable with standard tooling, helping to keep maintenance straightforward and predictable. Practical fit and application guidance for workshop use Designed for a 28 mm T-slot and specified with precise axial dimensions (A: 27.7, B: 125, E: 44, K: 18), the component offers a secure seating and correct alignment in slot-mounted assemblies. Packaged per unit, the fastener is suited to single-component replacements or staged upgrades of clamping systems. Selection should match slot width and fixture geometry; when in doubt, consult the technical data to confirm compatibility with the machine table and clamping hardware being used. Contact Metav Werkzeuge for precise ordering and application support: info@metav-werkzeuge.com or call +49 2822 7131930 to discuss suitability and delivery from Emmerich Technical data Article number: 4000603258NW SKU / UID: 4000603258NW Standard: DIN 787 Product type: T-slot screw Brand: AMF Facts T-slot width: 28 mm Thread: M24 Overall length: 200 mm Property class: 8.8 A: 27.7 B: 125 E: 44 K: 18 Packaging unit: 1 Special features Designed for machine tables and fixturing Standardised dimensions for interchangeability Heavy-duty fastening for clamping applications FAQ Is this fastener compatible with standard 28 mm T-slots? Yes. The T-slot screw DIN 787 (AMF) is specified for 28 mm T-slots and includes axial dimensions to ensure correct seating in standard slot systems. What does Grade 8.8 indicate for the screw? Grade 8.8 denotes a high-strength property class; the T-slot screw by AMF provides enhanced tensile and yield performance suitable for demanding clamping tasks. Can the fastener be used on modular fixture plates with deeper threaded engagement? Yes. The 200 mm overall length allows deeper engagement where required; consideration of thread engagement depth and slot clearance is recommended before installation. Which thread size is used and what tooling is needed? The component features an M24 metric thread; standard M24 tooling and torque practices for Grade 8.8 fasteners apply for installation and removal. What is the article number for ordering and reference? The article number is 4000603258NW (T-slot screw DIN 787, AMF), which should be quoted for precise procurement and documentation. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
200mm T-Slot Screw 22mm M20 DIN 787 Grade 8.8 - AMF
Take advantage of the combination of standardised fit, robust tensile performance and straightforward installation for reliable clamping in production setups; order the part directly via Metav Werkzeuge or contact our consultants for specification support. AMF T-slot bolt DIN 787 — 22 mm T-slot, M20, 200 mm, Grade 8.8 AMF T-slot bolt DIN 787 is a heavy-duty clamping element for 22 mm T-slots, designed for secure fixture assembly and machine-table fastening in industrial environments. Compliant with DIN 787 Fits 22 mm T-slots M20 thread, 200 mm length Grade 8.8 high tensile strength Secure clamping performance for machine tables The bolt provides a reliable mechanical interface for machine tables and modular fixturing thanks to its compatibility with 22 mm T-slots and an M20 threaded connection. These properties ensure a consistent and repeatable clamping action, which reduces setup time and minimises micro-movement under load. The overall length of 200 mm gives sufficient thread engagement for deep assemblies, while the standardised head geometry is intended to sit securely within the slot profile, improving positional stability during machining and assembly operations. Standardised fit for seamless interchangeability Manufactured to DIN 787, the component offers a predictable fit and geometry that simplifies parts replacement and system integration. The adherence to this norm means the head dimensions and slot interface are compatible with other DIN-conformant accessories, enabling quick interchange without bespoke adapters. For procurement and maintenance planning, the use of standardised elements reduces the risk of mismatches and supports consistent inventory management across workshops and production lines. Strength and durability suitable for demanding applications Specified as Grade 8.8, the fastener delivers elevated tensile and yield characteristics compared with lower-grade alternatives. This classification indicates enhanced resistance to shear and bending stresses encountered in heavy clamping scenarios, making the bolt suitable for medium to high-load fixtures. Where cyclic loads or vibration are present, selecting a high-tensile fastener like this reduces the likelihood of deformation and contributes to longer service intervals and fewer unplanned stoppages. Interface details and dimensional guidance Key interface dimensions are provided to aid design and assembly: additional dimensional values are A: 21.7 mm, B: 125 mm, E: 35 mm, K: 14 mm, which describe the head and engagement geometry for integration into standard clamping systems. These measured parameters support designers and engineers in verifying clearance, reach and engagement depth when planning fixture layouts or retrofitting new components into existing equipment. Practical installation and system compatibility The threaded M20 connection accepts widely available nuts and washers, allowing standard fastening practices to be applied. The fastener's design supports straightforward installation: insert into the 22 mm slot, align with the workpiece or clamp element, and secure using appropriate torque values for Grade 8.8 hardware. Where required, confirm torque and assembly procedures with tool manufacturers to ensure clamping force is consistent and safe for the application. Specification support and procurement assurance For procurement teams and workshop managers, the use of standardised, robust fasteners simplifies sourcing and reduces the variety of parts to be stocked. Metav’s role as a precision partner ensures that components are supplied reliably from the Emmerich hub, with quality controls aimed at delivering consistent product performance and traceable deliveries for production-critical hardware. For reliable supply of AMF Grade 8.8 T-slot bolts and expert advice on integrating them into existing fixtures, contact Metav Werkzeuge for immediate assistance at info@metav-werkzeuge.com or by phone on +49 2822 7131930 Technical data Article number: 4000603245NW SKU: 4000603245NW Standard: DIN 787 Core measurements T-slot width: 22 mm Thread: M20 Overall length: 200 mm Grade: 8.8 Additional dimensions: A 21.7 mm, B 125 mm, E 35 mm, K 14 mm Features Product type: T-slot bolt Brand: AMF Packaging unit: 1 FAQ What slot size does the bolt fit? The bolt is designed for a 22 mm T-slot, providing a standardised fit for compatible machine tables and fixtures. Which thread and length are specified for this T-slot bolt? This fastening element has an M20 thread and an overall length of 200 mm, suitable for assemblies requiring extended engagement. Is the bolt manufactured to any recognised standard? Yes, the bolt conforms to DIN 787, ensuring standard head geometry and interchangeability with other DIN-compliant components. What does Grade 8.8 mean for performance? Grade 8.8 indicates elevated tensile strength and yield properties, making the bolt suitable for demanding clamping scenarios where higher load resistance is required. How can engineers verify dimensional compatibility? Use the provided dimensions A 21.7 mm, B 125 mm, E 35 mm and K 14 mm to confirm head and engagement geometry against fixture drawings and slot profiles. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
200mm T-Slot Screw M20 With Nut And Washer, DIN 787 8.8 - AMF
Take advantage of a robust fastener that combines DIN 787 compliance with Grade 8.8 strength and a 200 mm reach for reliable fixturing; order directly via Metav Werkzeuge or consult our specialists for application advice. AMF T-slot screw DIN 787 — M20 thread, 200 mm, Grade 8.8 AMF T-slot screw DIN 787 for secure clamping in 20 mm T-slots, supplied complete with nut and washer for machine tables and fixture systems Conforms to DIN 787 T-slot standard Designed for 20 mm T-slot systems High-strength Grade 8.8 construction Supplied with nut and washer Secure clamping through standard compliance The DIN 787 specification guarantees standardised geometry for T-slot fasteners, enabling predictable assembly and interchangeability across machines and fixture plates. By meeting this norm, the M20 threaded fastener provides a verified interface that reduces alignment issues and speeds up setup. The standardised form also simplifies procurement and stock management in production environments, allowing planners to rely on consistent fit and function. Size and reach tailored for demanding fixtures With a 200 mm overall length and compatibility with a 20 mm T-slot, the screw is engineered to reach through thicker plates and clamping stacks while maintaining a secure thread engagement. The combination of M20 thread and extended shank length enables deeper clamping and flexibility in fixture design. Dimension references (A: 19.7; B: 125; E: 32; K: 12) support precise integration into assemblies and help machine planners verify clearances and gripping depths before installation. Proven strength for industrial use Constructed to Grade 8.8, the fastener delivers a balance of tensile strength and toughness suitable for heavy clamping applications. This property class indicates quenched and tempered steel performance levels commonly used in workshop and production settings to resist shear and tensile loads. The result is a dependable connection that maintains clamping force under cyclical loads, contributing directly to process stability and reduced rework. Ready-to-install delivery reduces assembly time Delivered complete with nut and washer, the fastener removes the need to source matching components separately, shortening the assembly chain and simplifying logistics. Packaged as a single unit, the product supports just-in-time workflows and minimises inventory complexity. The supplied fixing elements are matched to the thread size to ensure correct fit and reliable torque transmission during tightening. For reliable fixturing with AMF’s high-strength T-slot fastener, contact Metav Werkzeuge for ordering and bespoke advice — Metav Werkzeuge can confirm suitability for specific machine tables and provide delivery from Emmerich: info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: 4000833347NW SKU / UID: 4000833347NW Standard: DIN 787 Product type: T-slot screw Brand: AMF Thread: M20 T-slot width: 20 mm Total length: 200 mm Grade: 8.8 Includes: nut and washer Packaging unit: 1 Facts Thread size: M20 T-slot compatibility: 20 mm Overall length: 200 mm Dimension A: 19.7 Dimension B: 125 Dimension E: 32 Dimension K: 12 Standard: DIN 787 Special features Conforms to DIN 787 T-slot geometry High-strength Grade 8.8 fastener Supplied complete with matched nut and washer Suitable for machine tables and fixture systems FAQ What T-slot width is this fastener suitable for? The AMF T-slot screw is designed for a 20 mm T-slot, matching the DIN 787 profile for secure seating in standard machine table grooves. Does the delivery include fixing hardware? Yes, the product is supplied with a matched nut and washer, allowing immediate installation without sourcing additional components. What is the thread size and overall length of the fastener? The fastener features an M20 thread and an overall length of 200 mm, suitable for deeper clamping applications. Which standard does the screw comply with? This T-slot screw conforms to DIN 787, ensuring standardised geometry for compatibility across machines and fixtures. Can the SKU be used to order the exact item? Orders and enquiries can reference SKU 4000833347NW to ensure the correct AMF T-slot screw is supplied. Manufacturer: AMF; Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
200mm Three-Point Horizontal Clamp 3,650N Holding Force, 3,500N Clamping Force, 90° Massive Arm, Zinc-Plated - Kukamet
Benefit from a robust, galvanised design combined with a 3,650 N holding force and a secure safety lock that keeps production flowing with fewer interruptions; compact dimensions and a 200 mm arm support versatile fixturing. Order directly via Metav Werkzeuge or consult our specialists for application advice. Horizontal clamp 112 by Kukamet — galvanised lever clamp with safety lock and 3,650 N holding force The Horizontal clamp 112 is a lever-operated horizontal clamp designed for reliable workpiece fixation in jigs, fixtures and assembly stations where robust, repeatable clamping is required Galvanised finish for corrosion protection Massive holding arm with safety lock 3,650 N maximum holding force 200 mm arm for extended reach Dependable construction that minimises downtime The galvanised construction and massive holding arm deliver a durable solution for repetitive clamping tasks in industrial environments. Built to withstand workshop conditions, the clamp offers a consistent 3,650 N holding capacity while the rated pressing capacity of 3,500 N defines safe operating limits. The integrated safety lock reduces the risk of unintentional release during handling and assembly, contributing to steady cycle times and fewer rejects. This combination supports reliable production processes and lowers the frequency of replacements. Faster set-up and clear operational benefits As a lever-operated horizontal device, this clamp shortens set-up times and permits swift repositioning of parts. The 200 mm arm provides extended reach for slightly larger workpieces, while a compact mass of 0.73 kg keeps the unit lightweight for modular fixtures and tool carriers. Distinctions between holding force and pressing force are important: holding force indicates the maximum static retention capability, whereas pressing force denotes the usable clamp actuation force—both are balanced here to ensure effective clamping without overstressing components. The result is improved throughput with predictable, measurable performance. Simple integration and low-maintenance operation Designed for vertical foot mounting, the clamp installs cleanly into assembly tables or welded fixture plates, maintaining alignment at a 90° angle for standard horizontal clamping tasks. The galvanised surface reduces corrosion and the need for frequent upkeep, while the robust mechanics mean fewer interventions over time. A clear safety mechanism and straightforward lever action promote safe handling in shift work and automated stations. Durable materials and conservative ratings extend service life and reduce waste from premature replacements, supporting both operational efficiency and responsible resource use. For tailored clamping solutions from Kukamet, contact Metav Werkzeuge for technical consultation or to place an order — info@metav-werkzeuge.com · +49 2822 7131930 Technical data SKU: 112-4-D-L-C3 GTIN: 8680731500622 Brand: Kukamet Weight: 0.73 kg Core specifications Max holding force: 3,650 N Max pressing force: 3,500 N Arm length: 200 mm Clamp angle: 90° Features and design Galvanised material Vertical foot mounting Massive holding arm Safety locking mechanism FAQ What is the maximum holding force of the clamp? The maximum holding force of the Horizontal clamp 112 is 3,650 N, providing secure retention for most fixture applications. What mounting method is required? The clamp uses a vertical foot mounting arrangement, allowing installation on fixture plates and assembly tables at a 90° angle. Is the surface protected against corrosion? Yes, the unit has a galvanised finish that provides corrosion resistance and lowers maintenance requirements. What are the arm length and weight of the device? The clamp features a 200 mm arm and weighs 0.73 kg, making it suitable for modular fixtures and adjustable set-ups. Does the clamp include a safety mechanism? A mechanical safety lock is integrated into the lever clamp to prevent accidental release during use. Manufacturer: Kukamet Fevzi Çakmak Mah.10644 Sk. No:61-63 42050 Karatay / KONYA TÜRKİYE / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
Secure components with reliable workpiece clamps
Workpiece clamps, also known as workholding clamps or workholding devices, form the essential mechanical interface between machine and part in industrial fabrication. They keep components absolutely play-free, positionally accurate and vibration-resistant during milling, turning, drilling or grinding.
How workpiece clamps ensure process stability
A correctly specified clamping concept transfers the high cutting and feed forces of modern CNC machines into the machine table or spindle without deforming the part. The right combination of mechanical, hydraulic, pneumatic or magnetic solutions enables fast, repeatable setups and supports automated part change where required. Typical applications range from single-part turning to high-volume series milling and complex five-axis machining.
Concrete production benefits at a glance
- repeatable positioning: reduces scrap and rework
- high clamping forces: withstands aggressive cutting without part movement
- reduced set-up time: modular systems and quick-change features speed throughput
- improved surface finish: vibration damping for finer results and tighter tolerances
- flexible compatibility: vices, chucks, clamping plates and zero-point systems for diverse geometries
Why Metav's range is the practical choice
Metav combines decades of specialist know-how with a broad, handpicked range that democratises precision for workshops and industry alike. Based in Emmerich, Metav acts as a quality filter for the European market and supplies more than 250,000 products from precision metrology to complete workshop equipment. With the trust of over 48,000 customers, Metav offers a single-source approach that reduces supplier complexity and secures dependable delivery to your workbench.
Technical data
- function: mechanical interface between machine and workpiece
- primary requirements: absolute positional accuracy; vibration reduction; high clamping forces
- technologies: mechanical, hydraulic, pneumatic, magnetic
- typical components: machine vices; chucks; clamping plates; zero-point systems; pratzen; clamping jaws
- application areas: milling; turning; drilling; grinding; automated part change systems
- production benefits: reduced set-up time; enhanced process security; optimised series and single-part production
The practical summary
Workpiece clamps bring the stability and repeatability required to meet tight tolerances and excellent surface quality, making them indispensable across machining operations. Choosing the right workholding clamps and modular workholding devices is a decisive step towards higher productivity and consistent part quality.
FAQ
What types of workpiece clamps are suitable for automated machining?
Workholding clamps with quick-change modules, hydraulic actuation or magnetic systems are commonly used for automated machining. These workholding devices enable fast, repeatable part changes and integrate with zero-point systems.
How do workpiece clamps affect surface finish and tolerances?
A stable clamping concept minimises vibration and part movement; this improves surface finish and supports achieving narrow tolerances when using high-precision workpiece clamps or workholding devices.
Can the same workpiece clamps handle different part geometries?
Modular workholding clamps and adaptable clamping jaws allow flexible fixturing for varied geometries; combining vices, clamping plates and pratzen increases versatility on the shopfloor.
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com