Precision boring bars with internal coolant for deep hole accuracy
Boring bars with internal coolant are precision tools designed to enlarge and finish existing holes, delivering tight dimensional and form tolerances while preventing tool breakage and surface damage; they are essential for deep bores and blind holes where external cooling cannot reach the cutting edge. These systems force high-pressure coolant through axial channels directly to the cutter, which reduces thermal stress and efficiently evacuates chips, making them ideal for machining difficult-to-cut or long-chipping materials. As a compact tool solution they combine rigidity, chip control and cooling to improve cycle times and extend tool life, with the main advantages being enhanced hole quality, repeatability and reduced rework for production and maintenance machining operations.
20mm S16Q SVQBR Drill Bar SVQB for VBMT Indexable Inserts 107.5° 30mm Cut Height, 180mm Length - Teknik Makina
Take advantage of a compact, insert-ready boring solution that combines a 107.5° cutting geometry with a robust 16 mm shank for stable clamping and repeatable results; order the K216TM boring bar directly via Metav Werkzeuge or consult our specialists for application advice. K216TM Boring Bar — S16Q SVQBR, 107.5° for VBMT 1103 (Teknik Makina) The K216TM boring bar is a right-hand boring tool designed for indexable VBMT 1103 inserts, delivering controlled chip flow and reliable seating for medium-duty internal turning operations. 107.5° cutting angle for stable chip control Compatible with VBMT 1103 indexable inserts Ø20 mm cutting diameter, 180 mm overall length 16 mm shank for secure clamping and rigidity Greater stability for repeatable internal machining With a 16 mm shank and the ISO designation S16Q SVQBR, this boring bar offers a compact, rigid connection to standard toolholders. The profile and build reduce flex during engagement, which translates into more consistent bore tolerances and fewer rework cycles. Because the tool accepts VBMT 1103 indexable inserts, insert changes are quick and predictable, reducing downtime and keeping cycle times steady across batches. The design supports reliable seating and repeatability without complex set-up procedures. Predictable chip control and surface finish The 107.5° cutting angle and the tool’s right-hand orientation help to direct chips away from the cutting edge and workpiece, improving surface finish and lowering heat concentration at the cutting zone. A Ø20 mm cutting diameter together with a 30 mm cutting height gives a defined engagement length for stable cutting conditions; this combination supports consistent material removal rates for a wide range of standard steels and general workshop applications. The resulting process stability enhances efficiency and reduces the likelihood of tool-related interruptions. Practical integration for workshop use At 180 mm overall length and a weight of 0.276 kg, the bar is easy to handle while still offering sufficient reach for many common internal turning tasks. The tool’s compatibility with standard VBMT triangular inserts simplifies inventory management and reduces the variety of holders and inserts required at the workbench. Marked with a clear ISO code and compact dimensions, the device installs cleanly in turret or toolpost setups, helping to shorten changeover times and maintain throughput in production or maintenance environments. For supply, technical matching and rapid delivery of the Teknik Makina K216TM boring bar, contact Metav Werkzeuge in Emmerich — eMail info@metav-werkzeuge.com or phone +49 2822 7131930 Technical data Article number: K216TM Manufacturer: Teknik Makina ISO designation: S16Q SVQBR Facts Cutting angle: 107.5° Cutting direction: right-hand Cutting diameter: 20 mm Shank diameter: 16 mm Cutting height: 30 mm Overall length: 180 mm Weight: 0.276 kg Compatible inserts: VBMT 1103 Special features For indexable inserts Right-hand machining Compact, rigid shank Standard ISO mounting format FAQ Which insert type fits this boring bar? The K216TM boring bar is designed for VBMT 1103 indexable inserts and seats them in a standard triangular pocket for secure clamping. Is the bar suitable for left-hand cutting? No, the tool is configured for right-hand cutting direction only; opposite-hand operations require a corresponding left-hand tool. What is the ISO designation for mounting and identification? The bar is specified as S16Q SVQBR, which indicates a 16 mm shank and the SVQB pocket style compatible with VBMT inserts. Can the tool be used for deep-bore operations? With an overall length of 180 mm, the bar is intended for medium-reach internal turning; very deep bores may require a longer, purpose-built bar. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
20mm S16Q SVQCL Boring Bar For VCMT 1103 Inserts Left Cutting Direction, 16mm Shank - Teknik Makina
Take advantage of a rigid, ISO‑compatible tool holder that combines reliable left‑hand cutting geometry and compact dimensions to ensure consistent chip control and repeatable set‑ups; order the tool directly via Metav Werkzeuge or consult the technical team for application advice. Boring Bar K319TM — S16Q SVQCL holder for VCMT 1103 inserts, 16 mm shank (Teknik Makina) A Boring Bar K319TM designed for left‑hand turning operations with VCMT 1103 indexable inserts, suitable for workshops and production lines requiring standardised insert mounting and stable overhang control. *Left‑hand cutting for specific turning setups *S16Q SVQCL ISO designation for easy matching *16 mm shank, 180 mm overall length *Compatible with VCMT 1103 indexable inserts Consistent left‑hand geometry for predictable chip flow The holder provides a defined left‑hand cutting arrangement and a 107.5° cutting angle, delivering predictable chip formation and clearance during interrupted or continuous cuts. Matching the SVQC geometry to VCMT 1103 inserts reduces set‑up variation and lowers the risk of unexpected tool interference, which supports shorter cycle times and improved surface quality. By using an ISO‑style designation such as S16Q SVQCL, the tool can be integrated quickly into standard tool lists, helping to streamline fixture planning and inventory control. Compact, rigid dimensions that improve stability With a 16 mm shank, 20 mm diameter and 180 mm overall length, the holder balances reach and rigidity for short to medium overhang turning tasks. The 30 mm cutting height contributes to secure insert seating and repeatable clamping, which enhances dimensional stability of finished parts. At 0.281 kg, the assembly remains easy to handle while providing the inert mass necessary to suppress minor vibration in many common turning applications. These physical attributes translate directly into better tool life and consistent part tolerances. Fast integration into existing indexable‑insert tool systems The SVQC design is intended for quick insert replacement and simple clamping mechanics, enabling rapid reconditioning of the cutting edge and minimising downtime. The combination of an ISO designation, compatibility with widely used VCMT inserts and a standard shank size facilitates interchangeability across compatible tool holders and turrets. This standardisation supports predictable maintenance cycles and can reduce the number of special‑purpose tools required in a workshop, yielding operational efficiencies and easier stock management. For a precise left‑hand turning solution from Teknik Makina, contact Metav Werkzeuge in Emmerich for tailored application advice and rapid supply — info@metav-werkzeuge.com / +49 2822 7131930 Technical data SKU: K319TM Manufacturer: Teknik Makina ISO designation: S16Q SVQCL For inserts: VCMT 1103 Facts Shank diameter: 16 mm Diameter: 20 mm Overall length: 180 mm Cutting height: 30 mm Cutting angle: 107.5° Cutting direction: left Weight: 0.281 kg Special features SVQC style holder for indexable inserts Compatibility with VCMT 1103 inserts ISO‑compliant designation for easy replacement Compact design for improved rigidity and handling FAQ Which inserts fit this holder? The K319TM boring bar is designed for VCMT 1103 indexable inserts and the SVQC pocket geometry ensures correct seating and clamping. Is the cutting direction suitable for standard turret tools? This holder features a left‑hand cutting orientation; compatibility with turret mounting depends on the machine set‑up and turret clearances. What are the key dimensions to check for mounting? Important dimensions are the 16 mm shank, 180 mm overall length and 20 mm diameter, which determine clamping compatibility and overhang limits. How does the S16Q SVQCL designation help in workshop planning? The S16Q SVQCL ISO designation standardises the holder type, simplifying tool list integration and ensuring interchangeability with other ISO‑spec tooling. Can this holder be used for heavy roughing? The compact dimensions and inherent rigidity suit short to medium overhang operations; heavy roughing demands should be assessed against machine power, insert grade and clamping conditions. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com
20mm S16Q SVUBL Boring Bar For VBMT 1103 Indexable Inserts, Left-Hand 93° Cutting Angle, 180mm Overall Length - Teknik Makina
Take advantage of a compact boring solution that pairs a 16 mm shank with a Ø20 mm head and a 93° cutting angle for stable, left-hand internal turning; secure supply and expert advice through Metav Werkzeuge for seamless shop-floor integration. S16Q SVUBL Boring Bar – left-hand, for VBMT 1103 indexable inserts (Teknik Cutting Tools) A S16Q SVUBL boring bar engineered for left-hand internal turning with VBMT 1103 indexable inserts, offering compact dimensions and a stiff shank for reliable clamping and repeatable results. S16Q SVUBL boring bar for VBMT 1103 inserts Left-hand cutting direction, 93° cutting angle Ø20 mm head, 16 mm shank diameter Overall length 180 mm, cutting height 30 mm Stable clamping and predictable machining results The toolholder is designed around a 16 mm shank, combining rigidity with compact form to reduce deflection in confined bores. Compatibility with VBMT 1103 indexable inserts ensures a familiar insert geometry for many turning operations, while the Ø20 mm head maintains cutting strength without excessive overhang. This configuration reduces vibration and leads to more consistent tolerance retention across batch runs. For workshops that prioritise process reliability, the combination of a stiff shank and standard insert format supports predictable cycle times and fewer part rejections. Improved chip control and surface quality from geometry A 93° cutting angle matched to a 30 mm cutting height promotes favourable chip flow and axial stability during left-hand cuts. The insert seat and cutting geometry are optimised for controlled chip engagement, which helps to lower burr formation and improves surface finish in internal turning operations. When machining common materials with moderate cutting data, this geometry can reduce the need for secondary finishing, translating into time savings and lower downstream costs while preserving required surface integrity. Ready for quick set-up and efficient handling on the shop floor The bar’s ISO designation S16Q SVUBL simplifies tool selection and documentation; the concise overall length of 180 mm and the modest mass of 0.278 kg make tool handling and balancing straightforward during set-up. The left-hand orientation is clearly specified to avoid mix-ups with right-hand holders, and the standard shank diameter accelerates clamping in common tool posts. This straightforward adoption reduces set-up time and makes the holder suitable for mixed production environments where flexibility and short changeover are priorities. For dependable left-hand internal turning with VBMT 1103 inserts, contact Metav Werkzeuge in Emmerich to discuss the S16Q SVUBL by Teknik Cutting Tools and secure fast, reliable supply. Technical data SKU: K282TM Manufacturer: Teknik Makina ISO designation: S16Q SVUBL Description: SVUB for VBMT Indexable Inserts Core data Shank diameter: 16 mm Head diameter: 20 mm Overall length: 180 mm Cutting height: 30 mm Cutting angle: 93° Weight: 0.278 kg Features Left-hand cutting direction Compatible with VBMT 1103 indexable inserts Compact form for reduced overhang ISO-based designation for easy documentation FAQ Which insert type fits this holder? The holder accepts VBMT 1103 indexable inserts; the S16Q SVUBL design provides a standard seat for secure clamping and correct cutting geometry. Is the tool suitable for internal left-hand turning? Yes, the S16Q SVUBL is specified for left-hand cutting direction and is intended for internal turning applications where left-hand chip flow is required. What are the key dimensions to consider for setup? Key dimensions: 16 mm shank diameter, Ø20 mm head, overall length 180 mm, cutting height 30 mm; weight 0.278 kg (SKU K282TM). How does the cutting angle affect performance? The 93° cutting angle stabilises axial engagement and supports consistent chip formation, which helps to improve surface finish and reduce chatter in many internal turning tasks. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
20mm S16Q SVUBR Drill Bar For VBMT 1103 Indexable Inserts 93° Cutting Angle, 180mm Overall Length - Teknik Makina
Take advantage of a compact, right-hand toolholder that pairs with standard VBMT 1103 indexable inserts to reduce setup time and simplify inventory; the combination of a 16 mm shank and 180 mm overall length delivers a reliable balance of rigidity and accessibility for turning operations — order via Metav Werkzeuge or consult the Metav team for tailored advice. S16Q SVUBR Boring Bar — SVUB for VBMT indexable inserts, right-hand The S16Q SVUBR is a right-hand boring bar designed as a toolholder for VBMT 1103 indexable inserts, suitable for light to medium turning and finishing tasks in conventional CNC or manual lathe setups S16Q SVUBR boring bar with 16 mm shank Compatible with VBMT 1103 indexable inserts Overall length 180 mm, Ø 20 mm Cutting height 30 mm for stable engagement Reliable insert compatibility for consistent production results The design of this toolholder centres on compatibility with industry-standard VBMT 1103 indexable inserts, enabling fast insert changes and predictable cutting behaviour. By accepting a commonly stocked insert format, the holder reduces the variety of spare parts required and shortens downtime during tool changes. The ISO designation S16Q SVUBR indicates a standardized shank and mounting geometry, which simplifies integration into existing toolbanks and clamping systems while supporting repeatable machining cycles. Stable geometry for improved surface finish and tool life With a 16 mm shank, Ø 20 mm body and an overall length of 180 mm, the turning bar offers a compact footprint that limits overhang without sacrificing reach. The 30 mm cutting height and a 93° cutting angle provide a secure engagement for the insert, reducing vibration and promoting consistent chip formation. Lower tool vibration contributes directly to a superior surface finish and helps extend insert service life, delivering measurable gains in machining efficiency and cost per component. Practical handling and workshop advantages Engineered for right-hand cutting direction and straightforward clamping (designation 11 for the holder interface), this boring bar supports rapid setup and reliable repeatability in batch production. The modest mass (0.278 kg) reduces spindle load during short overhangs and makes handling simpler during tool changes. For operations where tool real estate and inventory rationalisation matter, the combination of compact dimensions and insert interchangeability makes the bar well suited to busy workshops and production cells that prioritise uptime and predictable throughput. Contact Metav Werkzeuge for precise ordering information on Teknik Cutting Tools S16Q SVUBR boring bars (SKU K206TM) and secure dependable supply from Emmerich — eMail info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: K206TM Manufacturer: Teknik Cutting Tools ISO designation: S16Q SVUBR Product name (EN): SVUB for VBMT indexable inserts Facts Shank diameter: 16 mm Overall length: 180 mm Diameter: 20 mm Cutting height: 30 mm Cutting angle: 93° Direction of cut: right Weight: 0.278 kg Special features Compatible with VBMT 1103 indexable inserts Clamping holder designation: 11 Right-hand toolholder Compact design for reduced overhang FAQ Which inserts fit this boring bar? The S16Q SVUBR boring bar accepts VBMT 1103 indexable inserts, a standard format for versatile turning and finishing applications. Is the tool suitable for left-hand machining? This holder is specified for right-hand cutting direction and is intended for right-hand turning operations. What are the main dimensions to consider for setup? Key dimensions include a 16 mm shank, Ø 20 mm body and 180 mm overall length, which determine reach and clearance in the toolpost or turret. What is the SKU and who manufactures the holder? The SKU is K206TM and the product is manufactured by Teknik Cutting Tools under the ISO designation S16Q SVUBR. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
20mm S16Q SVUCL Boring Bar for VCMT 1103 Indexable Inserts Left Cutting, 16mm Shank - Teknik Makina
Robust left‑hand boring bar with a secure SVUC pocket for VCMT 1103 indexable inserts, offering a stable 16 mm shank and 20 mm diameter for reliable internal turning; order via Metav Werkzeuge or consult our specialists for application-specific advice. Boring bar S16Q SVUCL — SVUC for VCMT indexable inserts, left‑hand (Teknik Makina) The Boring bar S16Q SVUCL is designed for left‑hand internal turning where secure clamping and repeatable insert positioning are essential Left‑hand orientation for specific turning tasks Suitable for VCMT 1103 indexable inserts 16 mm shank for rigid clamping 180 mm overall length for deep reach Stability and cutting performance for internal turning Built to deliver consistent results, this holder combines a 16 mm shank with a 20 mm diameter to reduce vibration during internal operations. The robust geometry supports precise tool positioning, which helps to maintain repeatable cutting conditions and predictable tool life. The 93° cutting angle contributes to controlled chip formation and a balanced cutting force, reducing deflection and improving surface finish in confined bores. Proven compatibility with indexable VCMT inserts The SVUC pocket is engineered for secure seating of VCMT 1103 inserts, enabling fast insert changes and reproducible clamping. The combination of insert type and pocket shape is optimised for common turning tasks, providing a cost‑effective solution when using replaceable cutting edges. Clear compatibility reduces setup time and simplifies tooling management in production environments that rely on standard indexable inserts. Efficient setup and left‑hand orientation for specialised tasks Designated S16Q SVUCL in ISO nomenclature, the holder features a compact form factor and a clamping designation of 11 for straightforward integration into existing toolposts and turret systems. The left‑hand configuration is suited to operations where opposed tool rotation or particular access constraints require reverse orientation. The holder’s manageable mass (0.28 kg) and standardised interface aid quick tool changes and secure mounting in most internal‑turning setups. Practical reach and workshop versatility With an 180 mm overall length and a cutting height of 30 mm, the toolholder offers practical reach for small to medium bores while keeping the tool projection moderate to preserve rigidity. This balance supports a range of internal turning tasks where secure insert seating and repeatable alignment are priorities. The compact weight and dimensions make the holder a sensible choice for busy workshops seeking reliable, easy‑to‑service tooling without complex fixtures. For tailored advice on integrating the S16Q SVUCL holder into specific turning applications, contact Metav Werkzeuge for specification support and fitment confirmation by phone +49 2822 7131930 or eMail info@metav-werkzeuge.com Technical data Article number: K300TM Manufacturer: Teknik Makina ISO designation: S16Q SVUCL Product description: SVUC for VCMT indexable inserts Core measurements Shank diameter: 16 mm Diameter: 20 mm Cutting height: 30 mm Overall length: 180 mm Cutting angle: 93° Weight: 0.28 kg Cutting direction: left Features & compatibility Compatible inserts: VCMT 1103 Clamping holder designation: 11 Designation (en): SVUC for VCMT indexable inserts Intended use: internal turning with indexable inserts FAQ Is this holder suitable for right‑hand turning? No. The holder is configured for left‑hand cutting; the S16Q SVUCL (K300TM) is specified for left‑hand internal turning applications. Which inserts fit the pocket of this holder? The pocket accepts VCMT 1103 indexable inserts; the SVUC seat is matched to that insert geometry for secure clamping and correct cutting edge position. What mounting dimensions should be checked before installation? Confirm shank interfacing and turret clearance: the tool has a 16 mm shank, a 20 mm outer diameter and 180 mm overall length, which should suit most compact internal turning setups. Can the holder be used for finishing operations? Yes. With stable clamping and a 93° cutting angle, the holder supports controlled cutting suitable for finishing and general internal turning tasks when paired with the appropriate insert grade. How quickly can inserts be replaced in this holder? Insert changes are straightforward due to the standard SVUC pocket and clamping design; the configuration is intended to reduce downtime for routine insert replacement. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com
20mm S16Q SVUCR Boring Bar SVUC for VCMT Indexable Inserts 16mm Shank, 93° Cutting Angle - Teknik Makina
Take advantage of the combination of a 16 mm shank for enhanced rigidity, compatibility with VCMT 1103 indexable inserts and a compact 180 mm overall length to improve internal turning stability and accessibility. Order the S16Q SVUCR boring bar directly via Metav Werkzeuge or ask our consultants if needed. S16Q SVUCR Boring Bar — 16 mm shank, for VCMT 1103 inserts | Teknik Makina The S16Q SVUCR is a boring bar engineered for right-hand internal turning operations, designed to accept VCMT indexable inserts for efficient, repeatable machining. S16Q SVUCR shank Ø16 mm Compatible with VCMT 1103 inserts 180 mm overall length for extended reach Right-hand cutting with 93° cutting angle Improved stability for consistent internal finishes A larger shank diameter directly increases the toolholder's rigidity, reducing vibration and chatter during internal turning. With a 16 mm shank and a modest overall length of 180 mm, this tool delivers a balance between reach and stiffness, which leads to more consistent surface finishes and longer insert life. The moderate weight (0.28 kg) keeps handling straightforward without compromising stability. For workshops facing variability in bore depths, this geometry supports repeatable results while keeping setup adjustments minimal. Proven insert system for fast maintenance and lower running costs The tool is specified for VCMT 1103 indexable inserts and uses an SVUC-style pocket to secure each insert reliably. Indexable inserts allow multiple cutting edges per insert, reducing tooling costs and machine downtime compared with brazed or one-piece cutters. The SVUC geometry ensures secure seating and repeatable locating, so insert replacement is quick and precise. For production environments that prioritise uptime and cost-efficiency, this configuration simplifies tool inventory while maintaining consistent cutting performance. Practical geometry that suits standard lathe setups The boring bar's 93° cutting angle and right-hand cutting orientation match common lathe toolpost arrangements and turning strategies. A diameter of 20 mm at the head provides necessary clearance while the overall tool profile supports accessibility into internal bores. The ISO designation reflects standard tooling conventions, making the bar compatible with many clamping systems and holders used across workshops. Where reliable, everyday internal turning is required, this tool combines straightforward compatibility with robust mechanical design. For procurement or technical advice on Teknik Makina's S16Q SVUCR boring bar (SKU K211TM) and its suitability for specific turning tasks, contact Metav Werkzeuge to arrange a detailed consultation or order support. Technical data SKU: K211TM Manufacturer: Teknik Makina ISO designation: S16Q SVUCR Type: SVUC for VCMT indexable inserts Facts Shank diameter: 16 mm Overall length: 180 mm Diameter: 20 mm Cutting height: 30 mm Weight: 0.28 kg Cutting angle: 93° Cutting direction: Right Special features For VCMT 1103 inserts SVUC pocket geometry Suitable for right-hand internal turning ISO-conforming designation FAQ Which inserts fit this boring bar? The boring bar accepts VCMT 1103 indexable inserts; the SVUC pocket secures the insert for repeatable positioning with Teknik Makina's S16Q SVUCR (SKU K211TM). Is the tool suitable for deep bores? The 180 mm overall length provides extended reach for many internal turning tasks, while the 16 mm shank helps maintain stiffness during deeper cuts. What is the cutting direction and angle? This bar is configured for right-hand cutting and features a 93° cutting angle, matching common lathe setups and standard turning strategies. How does the shank diameter affect performance? A 16 mm shank increases rigidity compared with smaller diameters, reducing vibration and improving surface finish and insert life under comparable cutting conditions. What standards does the tool follow? The product bears the ISO-style designation S16Q SVUCR, aligning it with established tooling conventions for compatibility across clamping systems. Manufacturer / Responsible: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com
20mm S16R PWLNR Boring Bar For WNMG 0604 Indexable Inserts, 95° Cutting Angle, 40mm Cutting Height - Teknik Makina
Take advantage of a robust ISO S16R PWLNR design combined with compatibility for WNMG 0604 indexable inserts and a compact 16 mm shank to secure repeatable turning results; order directly via Metav Werkzeuge or consult our machining specialists for application advice. Teknik Makina S16R PWLNR (PWLN for WNMG) Boring Bar — 16 mm shank, 200 mm overall length The S16R PWLNR boring bar is a right-hand toolholder for external turning using WNMG 0604 indexable inserts, designed for vibration‑resistant finishing and consistent component tolerances. ISO S16R PWLNR shank design Compatible with WNMG 0604 inserts 200 mm overall length for extended reach Right‑hand cutting, 95° cutting angle Stable clamping for repeatable turning accuracy A compact 16 mm shank combined with the tool’s ISO profile provides stable clamping and minimises tool overhang. Reduced vibration leads directly to improved surface finish and more predictable tool life, which supports process reliability in series production. The bar’s compatibility with WNMG 0604 indexable inserts makes insert changes fast and cost‑effective, allowing workshops to standardise on a commonly available insert format without sacrificing stability. Optimised geometry for efficient cutting performance The toolholder’s 95° cutting angle and right‑hand cutting orientation give a neutral entry that favours balanced chip flow and consistent contact with the workpiece. A cutting height 40 mm and a nominal diameter of 20 mm ensure correct insert siting and secure turning engagement, which helps reduce chatter during finishing operations. These geometric choices translate into shorter machining cycles and a lower scrap rate when paired with suitable WNMG grades. Practical standardisation for workshop efficiency Designed to integrate with common clamping systems, the bar accepts a clamping holder size 06 and an ISO designation that simplifies inventory management and tool selection. With a 200 mm overall length the tool provides reach for medium‑range external turning without excessive overhang, and a low mass (0.316 kg) that contributes to rapid spindle response. The combination of familiar insert format and compact dimensions makes this boring bar a pragmatic choice for workshops aiming to streamline tooling across multiple lathes. Contact Metav Werkzeuge today to discuss how Teknik Cutting Tools' S16R PWLNR boring bar (SKU P380TM) can improve machining stability and part quality — call +49 2822 7131930 or email info@metav-werkzeuge.com Technical data Article number: P380TM Manufacturer: Teknik Makina ISO designation: S16R PWLNR Product name: PWLN for WNMG Indexable Inserts Core specifications Shank diameter: 16 mm Cutting height: 40 mm Overall length: 200 mm Diameter: 20 mm Weight: 0.316 kg Cutting angle: 95° Cutting direction: right Special features Compatible with WNMG 0604 inserts Clamping holder size: 06 Right‑hand cutting orientation For PWLN insert type designed for WNMG FAQ Which insert type is recommended for this toolholder? The Teknik Makina S16R PWLNR boring bar (SKU P380TM) is designed for WNMG 0604 indexable inserts and seats them securely for reliable cutting performance. What is the shank diameter and how does it affect stability? The bar features a 16 mm shank, which provides a compact profile with good clamping stiffness; this helps to reduce vibration and maintain consistent tolerances during turning. Is the tool suitable for left‑hand turning? This version is configured for right‑hand cutting; select the matching left‑hand variant if counter‑direction machining is required. How does the 95° cutting angle benefit finishing operations? A 95° cutting angle offers a neutral approach that supports controlled chip formation and even tool contact, aiding surface finish and dimensional repeatability in finishing passes. What clamping holder does this boring bar require? The boring bar matches a clamping holder size 06, facilitating integration into common toolholding systems and simplifying changeover Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
20mm S20Q SCLCR Drill Bar SCLC for CC-09T3 Indexable Inserts, 95° Cutting Angle, 180mm Length - Teknik Makina
Take advantage of a rigid, CNC-ready design that combines secure clamping, Ø20 mm cutting diameter and compatibility with CC-- 09T3 indexable inserts for fewer tool changes and consistent surface quality. Order the boring bar directly via Metav Werkzeuge or contact our consultants for machining advice. Boring bar SCLC for CC-- Indexable Inserts (S20Q SCLCR) — 180 mm, Ø20 mm The Boring bar SCLC for CC-- Indexable Inserts is a right-hand turning tool designed for medium-reach internal and external turning operations with indexable CC-- 09T3 inserts. Right-hand cutting for conventional turning Compatible with CC-- 09T3 indexable inserts 180 mm overall length for extended reach 25 mm shank diameter for secure clamping Stable clamping for consistent machining accuracy The bar’s 25 mm shank diameter and robust geometry provide a stable connection between toolholder and spindle, which reduces vibration and improves repeatability. With the S20Q SCLCR ISO designation, the component is intended for secure mounting in standard clamping holders and, as a consequence, delivers a predictable cutting behaviour that is useful in both serial production and precision workshop work. A controlled interface between insert and body, together with the defined 95° cutting angle, helps to maintain tool life and achieve tighter tolerances on turned surfaces. Reduced downtime through indexable insert compatibility Designed for indexable inserts, the tool accepts CC-- 09T3 plates, allowing rapid insert changes and straightforward re-indexing. This arrangement minimises non-productive time compared with brazed or solid-carbide solutions and supports efficient shift patterns in production. The holder’s designated clamping code 09 ensures correct fitment in compatible toolholders, so changeovers are faster and easier to standardise across a shop floor, enhancing overall throughput and reducing cost per component. Reach and accessibility for deeper bores and shoulders With an overall length of 180 mm and a cutting diameter of Ø20 mm, the turning bar provides the reach required for moderate-depth internal work and for operations near shoulders where tool clearance is critical. The 40 mm cutting-edge height supplies adequate support for the insert seat, which helps to avoid chatter when machining features with restricted access. For operations that require a balance of reach and rigidity, this tool offers a practical compromise that preserves surface quality while granting necessary access. Workshop-grade reliability and straightforward specification Weighing approximately 0.612 kg, the component is compact yet built to withstand routine machining cycles. The right-hand cut, clearly stated by the ISO code and the product specification, establishes its intended orientation and prevents ambiguity during tool setup. Where process stability and predictable maintenance intervals are priorities, the bar’s straightforward design and insert system simplify inventory and spare-part management. The combination of these technical attributes supports reliable production and predictable tool maintenance. Contact Metav Werkzeuge for individual application guidance or to request technical documentation—email info@metav-werkzeuge.com or call +49 2822 7131930 for direct assistance and ordering via Metav Werkzeuge Technical data Article number: K114TM Brand: Teknik Makina ISO designation: S20Q SCLCR SKU: K114TM Facts Diameter: 20 mm Overall length: 180 mm Shank diameter: 25 mm Cutting height: 40 mm Weight: 0.612 kg Cutting angle: 95° Special features Compatible inserts: CC-- 09T3 Cutting direction: right Clamping holder code: 09 For indexable inserts SCLC for CC-- series FAQ Which inserts fit this boring bar? The boring bar accepts CC-- 09T3 indexable inserts and is specified as SCLC for CC-- applications, suitable for standard turning and profile work. Is the cutting direction right- or left-hand? This tool is manufactured for right-hand cutting and is defined as such by the ISO designation S20Q SCLCR. What are the key dimensions of the tool? Key dimensions are Ø20 mm cutting diameter, 180 mm overall length, 25 mm shank diameter and 40 mm cutting height; weight approximately 0.612 kg. Which ISO designation identifies this tool? The tool is designated S20Q SCLCR, indicating its shank and head geometry for standard clamping systems. Is this tool suitable for CNC lathes and turning centres? Yes, the construction and ISO format of the tool make it suitable for CNC lathes and turning centres using compatible clamping holders and CC-- 09T3 inserts. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com
20mm S20S SCLCR Drill Bar For CC-- 09T3 Indexable Inserts, Right-Hand 95° Cutting Angle, 25mm Shank Diameter - Teknik Makina
Take advantage of a rigid holder with a 20 mm cutting diameter and a 25 mm shank for stable clamping; the right‑hand S20S SCLCR design accepts CC-- 09T3 indexable inserts for efficient external turning — order directly via Metav Werkzeuge or consult the team for technical matching. S20S SCLCR boring bar (SCLC for CC-- indexable inserts) by Teknik Makina The S20S SCLCR boring bar is a right‑hand external turning holder engineered for use with CC-- 09T3 indexable inserts, suited to precision turning tasks on CNC lathes and conventional turning centres. Right-hand cutting orientation 20 mm cutting diameter 25 mm shank diameter for stable clamping Compatible with CC-- 09T3 inserts Improved rigidity for consistent surface finish A larger shank diameter delivers noticeable stiffness; the 25 mm shank reduces deflection under load and improves repeatability during interrupted cuts. The construction supports a 20 mm effective cutting diameter and an overall length of 250 mm, which together provide a balance between accessibility and rigidity. For workshops that prioritise dimensional consistency, this toolholder minimises chatter and helps achieve a reliable surface finish with fewer rework cycles. Faster indexable insert changes and predictable tool life Designed for CC-- 09T3 indexable inserts, the holder simplifies tool management by separating cutting geometry from the holder itself. The ISO designation S20S SCLCR clarifies the mounting geometry and insert pocket orientation for quick replacements. The right‑hand cutting direction and a 95° cutting angle are suited to conventional external turning operations; this reduces setup time and keeps machines productive, while the lightweight construction (approx. 0.78 kg) makes handling and changeover straightforward without compromising stability. Seamless integration into production workflows With its standard interface and clear compatibility, the bar is ready for direct integration into multi‑station turret systems and single‑point turning setups. The holder’s geometry supports predictable chip flow when matched with the specified inserts, aiding consistent cycle times. The compact overall length and defined cutting height (approx. 40 mm) allow planners to make concise tool lists for jobs that require short‑setup times and high repeatability. Choosing a defined holder‑and‑insert system helps workshops reduce inventory complexity and streamline tool reconditioning processes. For detailed technical matching, stock availability or to request a tailored recommendation from Metav Werkzeuge, contact Metav Werkzeuge in Emmerich via e‑mail at info@metav-werkzeuge.com or by phone on +49 2822 7131930 — Metav’s specialists will advise on the best holder and insert pairing for the intended turning application Technical Data SKU: K115TM Brand: Teknik Makina ISO designation: S20S SCLCR Type: SCLC for CC-- Indexable Inserts Cutting direction: right Facts Diameter: 20 mm Shank diameter: 25 mm Overall length: 250 mm Cutting height: 40 mm Weight: 0.78 kg Cutting angle: 95° Special features Compatible inserts: CC-- 09T3 Right‑hand external turning holder Suited to CNC lathes and turret turning applications ISO‑standard toolholder interface FAQ What inserts fit this holder? The holder accepts CC-- 09T3 indexable inserts; the S20S SCLCR configuration is designed specifically for that insert family to ensure secure seating and repeatable geometry. Is the tool suitable for right‑hand turning only? Yes, the design and pocket orientation of the S20S SCLCR boring bar are configured for right‑hand cutting operations on external turning tasks. How does the shank diameter affect performance? A 25 mm shank increases rigidity compared with smaller holders; this reduces deflection during cutting and contributes to improved dimensional accuracy and surface quality when using the bar in typical turning cycles. Which machines is this holder compatible with? The holder is compatible with standard turret and toolpost mounting systems that accept the ISO S20S SCLCR form; verify turret clearance and projection length against the 250 mm overall length before installation. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
20mm SCLC Drilling Bar 200mm Overall Length, Left-Hand 95° Cutting Angle - Teknik Makina
Take advantage of a compact, ISO‑matched boring solution that combines secure clamping, compatibility with CC-- 09T3 indexable inserts and a left‑hand cutting orientation for specialised turning tasks; order the tool directly via Metav Werkzeuge or consult the technical team if additional data is required. K241TM Boring Bar — S16R SCLCL profile, for CC-- 09T3 indexable inserts (left‑hand) A robust K241TM boring bar engineered for internal turning with indexable inserts, ideal for left‑hand operations and precise insert clamping in CNC turning applications. ISO S16R SCLCL profile for stable clamping Suitable for CC-- 09T3 indexable inserts Left‑hand cutting direction, 95° cutting angle 16 mm shank with 200 mm overall length Consistent rigidity and repeatable bore quality The S16R SCLCL configuration delivers a stable mounting interface, which reduces vibration and supports consistent bore geometry. With a 16 mm shank and an outer diameter of 20 mm, the toolholder provides a compact footprint that assists in maintaining concentricity during internal turning. The measured cutting height of 30 mm positions the insert correctly for reliable cutting engagement, while the tool's mass (approx. 0.317 kg) is low enough for quick tool changes without compromising stability. This mechanical balance improves dimensional repeatability and surface finish in serial production. Optimised for CC-- 09T3 inserts and left‑hand machining Designed specifically for CC-- 09T3 indexable inserts, the bar accepts the standard insert format and the associated clamping geometry for secure seating. The 95° cutting angle is matched to left‑hand cutting orientation, which moderates radial loading and promotes controlled chip flow in many internal turning setups. As a result, insert life and process reliability are improved, and operators benefit from predictable cutting forces when machining cast components or steels compatible with indexable‑insert turning. Easy selection and integration into the toolroom The ISO S16R SCLCL designation simplifies tool selection and ensures compatibility with common turret and tailstock clamping systems that accept this profile. With a 200 mm overall length and a compact shank, the bar suits confined bores and multi‑station toolchains where space is limited. The stored specification—shank diameter, overall length, cutting angle and compatible insert type—enables straightforward documentation for tool‑life planning and spare‑part inventory without additional measurement steps. Operation, maintenance and workshop benefits The straightforward geometry and standard clamping size (09 holder reference) reduce setup time and lower the learning curve for machinists familiar with indexable insert systems. The absence of special coatings or proprietary fittings means the tool integrates with existing insert ranges and collet or block holders. For production environments seeking a dependable boring solution, the combination of ISO conformity, left‑hand cut capability and insert compatibility supports efficient changeovers and predictable process windows. For reliable supply and technical advice on the Teknik Makina K241TM boring bar, contact Metav Werkzeuge in Emmerich via info@metav-werkzeuge.com or call +49 2822 7131930 Technical data SKU: K241TM Manufacturer: Teknik Makina ISO designation: S16R SCLCL For indexable inserts: CC-- 09T3 Cutting direction: left Facts Shank diameter: 16 mm Cutting height: 30 mm Diameter: 20 mm Overall length: 200 mm Weight: 0.317 kg Cutting angle: 95° Special features Left‑hand cutting orientation Compatible insert size: 09 holder reference ISO S16R SCLCL profile Suited for internal turning with indexable inserts FAQ What insert type fits the tool? The K241TM boring bar is designed for CC-- 09T3 indexable inserts and the clamping geometry corresponds to that insert family. Is the cutting orientation left‑hand or right‑hand? This tool is specified for left‑hand cutting; the 95° approach angle is configured accordingly. Which shank and overall dimensions are offered? The bar has a 16 mm shank, an outer diameter of 20 mm and an overall length of 200 mm, as stated for the K241TM. Can this boring bar be used in confined bores? Yes, the compact shank and 200 mm overall length make the bar suitable for restricted internal turning tasks. What does the ISO designation S16R SCLCL indicate? The ISO S16R SCLCL code identifies the shank size, handing and head style, allowing straightforward matching with compatible holders and turret stations for the K241TM. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
20mm SCLC Indexable Insert Drill Rod 21mm Shank 180mm Length 95° Cutting Angle - Teknik Makina
Take advantage of the combination of S18Q SCLCR ISO mounting, a 21 mm shank and proven insert compatibility with CC-- 09T3 to keep turning operations precise and service intervals predictable — order the part directly via Metav Werkzeuge or consult our specialists for application matching. Boring bar K112TM – S18Q SCLCR, 180 mm, ø20 mm for CC-- 09T3 indexable inserts (Teknik Makina) The Boring bar K112TM is a right‑hand external boring bar designed for secure insert clamping and stable finishing in turning applications, compatible with CC-- 09T3 indexable inserts and conventional toolholders S18Q SCLCR ISO designation for secure mounting Compatible with CC-- 09T3 indexable inserts 21 mm shank, ø20 mm cutting diameter 180 mm overall length, robust 95° cutting angle Stable mounting for consistent bore quality The S18Q SCLCR ISO designation provides a proven interface for rigid clamping and repeatable positioning. With a 21 mm shank and precision Machined seating, the holder reduces vibration and runout, which directly improves surface finish and prolongs insert life. The combination of a compact shank and a ø20 mm cutting diameter ensures the tool maintains stability in constrained set‑ups while permitting sufficient overhang for common bores. This structural balance supports efficient machining and predictable results across repetitive batches. Fast insert changes and controlled cutting geometry Engineered for CC-- 09T3 inserts, this tool holder accepts standard indexable inserts, allowing quick replacement without regrinding. The 95° cutting angle and 38 mm cutting height offer a geometry that favours controlled chip flow and effective load distribution at the cutting edge. Indexable inserts enable a practical cost/performance compromise: only the cutting edge is renewed, which reduces downtime and keeps tooling costs transparent. Where process stability and turnaround matter, this approach streamlines operations. Compact dimensions for workshop flexibility and traceable supply An 180 mm overall length and a weight of 0.436 kg make the bar easy to handle and mount in most lathe tool posts designed for metric shanks. The right‑hand cutting direction suits standard turning cycles; the ISO designation simplifies identification and procurement. Supplied by Teknik Makina, the component is part of a focused supply chain that Metav Werkzeuge supports from Emmerich — benefiting from central stock and quality control. The result is a pragmatic tool option for production and maintenance environments that value both precision and reliable availability. For tailored advice on integrating the S18Q SCLCR boring bar from Teknik Makina into existing tooling setups, contact Metav Werkzeuge for technical guidance and assured delivery from Emmerich Technical Data Article number: K112TM Manufacturer: Teknik Makina ISO designation: S18Q SCLCR Type description: SCLC for CC-- Indexable Inserts Facts Shaft diameter: 21 mm Cutting diameter: 20 mm Cutting height: 38 mm Overall length: 180 mm Weight: 0.436 kg Cutting angle: 95° Cutting direction: right Special features Compatible inserts: CC-- 09T3 Clamping size: 09 Bezeichnung_2_en: SCLC for CC-- Indexable Inserts bohrstange_bezeichnung_iso: S18Q SCLCR FAQ Which inserts fit this boring bar? The tool is designed for CC-- 09T3 indexable inserts; insert compatibility is stated on the product data and suits standard CC-- geometry. What is the shank size and how is it mounted? Mounting is by the S18Q SCLCR ISO interface; the shank diameter is 21 mm, so a holder or tool post accepting a 21 mm shank is required. Is the cutting direction suitable for conventional turning cycles? Yes, the bar is right‑hand cutting; the orientation matches standard right‑hand turning operations for external bores. What are the key dimensions for workshop planning? Key values: 20 mm cutting diameter, 38 mm cutting height, 180 mm overall length and weight 0.436 kg, useful when checking clearance and balance for the machine Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
20mm SVQC For VCMT Indexable Insert Drill Rod S16Q SVQCR, Right-Hand 107.5° 30mm Cutting Height - Teknik Makina
Efficient internal turning and reliable insert clamping result from the combination of a compact 16 mm shank diameter and compatibility with VCMT 1103 indexable inserts; the 107.5° cutting angle and 180 mm reach support stable machining with reduced vibration. Order the S16Q SVQCR boring bar directly via Metav Werkzeuge or consult the Metav team for technical guidance. S16Q SVQCR Boring Bar – SVQC for VCMT 1103 Inserts, 16 mm Shank (Teknik Makina) The S16Q SVQCR is a right-hand SVQC boring bar designed for internal turning with VCMT 1103 indexable inserts, offering a compact 16 mm shank for standard toolholders. Right-hand SVQC geometry for secure clamping Compatible with VCMT 1103 indexable inserts 16 mm shank diameter for standard toolholders 180 mm overall length for deep internal reach Improved stability and repeatable accuracy for internal turning The S16Q SVQCR combines a 16 mm shank diameter with a balanced, lightweight design to reduce overhang-induced vibration and enhance surface finish in turning operations. The SVQC clamping arrangement secures the insert reliably, which translates into consistent tool life and fewer adjustments on the machine. The 107.5° cutting angle is optimised to support predictable chip flow and modest cutting forces, making the tool a pragmatic choice where repeatability and process stability are priorities. Fast insert changes and broad workshop compatibility Designed to accept VCMT 1103 indexable inserts, the bar simplifies insert replacement and set-up times, enabling quicker changeovers and reduced downtime in batch production. The SVQC clamping geometry ensures a firm seat for the insert, diminishing play and improving dimensional stability. With a right-hand cutting orientation, integration into existing turning programmes and tool stations is straightforward, supporting standard machining routines without the need for special adapters. Practical dimensions for medium-depth boring tasks A 20 mm tool diameter and 180 mm overall length provide sufficient reach for many internal operations while keeping rigidity high. At just 0.281 kg, the bar is light enough to limit centrifugal and inertial effects at speed yet robust in construction for everyday workshop use. These dimensions favour shorter set-ups and make the tool suitable for small-batch work as well as serial production where compact, rigid tooling improves cycle consistency. Applications and handling considerations This SVQC boring bar is geared towards indexable turning tasks where quick insert indexing and dependable clamping are required. The S16Q SVQCR is a pragmatic option for turning and facing within bore diameters compatible with a 20 mm tool body and for operations that benefit from a 107.5° cutting angle. Proper mounting in a compatible toolholder and adherence to recommended insert selection will ensure the expected balance of tool life and machining quality. For reliable supply and personalised advice on the Teknik Makina S16Q SVQCR boring bar, contact Metav Werkzeuge—email info@metav-werkzeuge.com or call +49 2822 7131930 for detailed technical consultation and ordering assistance. Technical Data Article number: K221TM Brand: Teknik Makina Designation: Boring bar – SVQC for VCMT Indexable Inserts ISO designation: S16Q SVQCR Dimensions & core data Shank diameter: 16 mm Cutting height: 30 mm Tool diameter: 20 mm Overall length: 180 mm Weight: 0.281 kg Cutting angle: 107.5° Features & compatibility Compatible with VCMT 1103 indexable inserts Right-hand cutting direction SVQC clamping geometry ISO designation S16Q SVQCR FAQ What inserts fit this boring bar? The bar is compatible with VCMT 1103 indexable inserts; the SVQC clamping format secures the insert for indexable turning tasks. Is the cutting direction fixed or reversible? The tool is specified as right-hand, so it is intended for right-hand cutting operations. What is the shank size and why does it matter? The shank diameter is 16 mm, which determines compatibility with standard toolholders and affects rigidity during internal machining. How long is the bar and what reach does that provide? The overall length is 180 mm, offering medium internal reach while maintaining a balance between accessibility and stiffness. Does the bar have an ISO designation for ordering? Yes, the ISO designation is S16Q SVQCR, which simplifies ordering and ensures correct specification. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com
20mm Thread Milling Cutter For S14 S21 S30 S40 Indexable Inserts, For S40 Inserts - Teknik Makina
Take advantage of reliable thread milling compatibility and robust mounting for consistent cycle times; the combination of a 20 mm shank and 93 mm overall length ensures stable clamping and extended reach for typical CNC operations — order directly via Metav Werkzeuge or consult the team for application support. Thread milling cutter DC214TM — indexable inserts S14–S40, 20 mm shank (Teknik Makina) The Thread milling cutter DC214TM is a purpose-built tool for CNC thread milling with indexable inserts, offering stable mounting and versatile insert compatibility for production and repair shops alike Compatible with S14, S21, S30 and S40 inserts 20 mm shank for secure clamping 93 mm overall length for extended reach Reliable compatibility that reduces setup time The design focuses on straightforward integration into existing tooling systems. With compatibility for S14, S21, S30 and S40 indexable inserts, the cutter allows fast adaptation to different thread forms without replacing the entire tool body, which reduces inventory complexity. The construction supports repeatable positioning and predictable chip control, delivering measurable time savings during changeovers and set‑up — a practical advantage in batch production and maintenance work. Stable clamping and simple insert replacement for uptime A 20 mm shank provides a firm interface with common holders, improving runout stability and minimising vibration under load. Insert retention is secured with an M2.5x7 Torx screw, tightened with a T8 key, which enables quick, tool‑assisted insert changes and precise clamp force. The 93 mm overall length offers added reach for recessed or awkward thread locations while maintaining sufficient rigidity for consistent thread form, contributing directly to process reliability on the shop floor. Optimised for thread milling operations in CNC environments Engineered as a cutting tool for thread generation rather than conventional tapping, the cutter supports indexed insert technology to allow controlled multiple‑pass milling. This method often provides better chip evacuation and less axial thrust compared with solid taps, which can increase tool life in interrupted cuts. The product is classified under eCl@ss 21180805 and ETIM EC011860, indicating its placement within standardised tool taxonomies and easing product selection in industrial procurement systems. Why procurement specialists choose Teknik Makina through Metav Werkzeuge Sourcing this cutter via Metav Werkzeuge combines manufacturer performance with distributor reliability. Metav’s Emmerich hub acts as a quality filter for the European market, supplying precision tools with consistent stock availability and technical consultation. For purchasing managers and workshop supervisors, the benefit is straightforward: consolidated sourcing, dependable supply chains and industry knowledge that supports efficient integration of the tool into production processes. For tailored technical advice and reliable supply of the Teknik Makina Thread milling cutter DC214TM, contact Metav Werkzeuge in Emmerich at info@metav-werkzeuge.com or +49 2822 7131930 for precise recommendations and prompt dispatch. Technical data Article number: DC214TM Name: Thread milling cutter For indexable inserts: for S14, S21, S30 and S40 Indexable Inserts Manufacturer: Teknik Makina ETIM: EC011860 eCl@ss: 21180805 Numerical data Shank diameter: 20 mm Cutting diameter: 20 mm Overall length: 93 mm Materials & special features Torx screw: M2.5x7 Torx key size: T8 Application: thread milling operations FAQ Which insert sizes are compatible with this cutter? The DC214TM is compatible with S14, S21, S30 and S40 indexable inserts as specified, allowing selection of insert grades and geometries to suit material and thread form. What is the shank size and why does it matter? The cutter features a 20 mm shank; this dimension provides a stable contact area in the toolholder, improving runout and contributing to more accurate thread profiles during machining. How are inserts secured and replaced? Inserts are secured with an M2.5x7 Torx screw and require a T8 key for removal and fitting, enabling quick and repeatable insert changes for minimal downtime. Is the cutter suitable for deep or recessed threads? With a 93 mm overall length, the tool offers extended reach for recessed thread positions while maintaining sufficient rigidity for reliable machining results. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
20mm Thread Milling Shank For Internal Threads With Internal Coolant, 16 IR Compatible - Teknik Makina
Take advantage of a robust combination of precise internal coolant delivery and proven insert compatibility to reduce cycle times and improve process reliability; order the K327-3TM directly via Metav Werkzeuge or consult their technical team for specification matching. K327-3TM Internal Thread Boring Bar — 20 mm shank, internal coolant, for 16 IR inserts (Teknik Makina) The K327-3TM is a compact internal threading tool designed for precision internal threads using IR indexable inserts, offering internal coolant for controlled chip evacuation in confined bores Internal coolant for efficient chip removal For 16 IR indexable inserts 20 mm shank diameter, 170 mm overall length Torx clamping screw M3.5x11, key T8 Faster, cleaner internal threading through built-in coolant The combination of an integrated internal coolant channel and a rigid construction delivers measurable process advantages: consistent lubrication and chip flushing reduce tool wear and prevent built-up edge, while stable cutting conditions improve dimensional precision. Built for indexable-insert threading, the bar ensures effective chip control in blind and through bores, helping to maintain surface quality and reduce secondary cleaning operations. Where higher throughput is required, the tool body’s coolant feed supports longer uninterrupted cycles and more predictable tool-life behaviour. Reliable clamping and repeatable set-up for workshop efficiency Clamping is secured by a Torx M3.5x11 screw and tightened with a T8 key, offering a fast, repeatable insert change procedure that supports short set-up times. The 20 mm shank diameter and a 170 mm overall length provide a balance of accessibility and rigidity for common internal threading tasks. Compatibility with 16 IR indexable inserts simplifies inventory and stocking decisions, since standard insert geometries can be used across multiple operations. The straightforward mechanical interface reduces set-up variability and contributes directly to improved first-pass yield. Easy integration into production and low-maintenance operation Designed for straightforward workshop integration, the tool accepts industry-standard IR inserts and requires only simple periodic checks: insert condition, clamping torque and coolant passage clearance. The compact design minimises interference in crowded fixtures while the internal coolant reduces the need for external flushing arrangements. For procurement and long-term planning, the tool is an economical option that supports predictive maintenance strategies and reduces operator handling time, aligning with quality-focused production routines. Contact Metav Werkzeuge for precise ordering and application advice on the K327-3TM internal thread boring bar; technical specialists in Emmerich can confirm suitability for specific jobs — email info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: K327-3TM Designation: Internal threading / thread boring bar Manufacturer: Teknik Makina Suitable for inserts: 16 IR Internal coolant: Yes Facts Shank diameter: 20 mm Overall length: 170 mm Torx screw: M3.5x11 Torx key: T8 Special features For inside thread with IR indexable inserts Internal coolant channel Torx clamping system for quick insert changes Compact, rigid design for repeatable set-up FAQ What insert type does this tool accept? The K327-3TM accepts 16 IR indexable inserts designed for internal threading operations. Does the bar supply coolant to the cutting edge? Yes — the tool features an internal coolant channel that delivers lubrication directly to the cutting zone to aid chip evacuation. What are the key dimensions to check for machine compatibility? Check the 20 mm shank diameter and 170 mm overall length to ensure proper clearance and fit-up in existing toolholders. How is the insert secured and which fastening tools are required? The insert is clamped with a Torx M3.5x11 screw tightened with a T8 key for reliable, repeatable clamping. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
21mm Thread Milling Cutter For S12 S14 S21 S30 S40 Indexable Inserts, M4x10 Torx Screw - Teknik Makina
Take advantage of the combination of broad insert compatibility, a compact Ø21 mm cutting diameter and a secure 20 mm shank for consistent, high-precision thread milling; order the thread milling cutter directly via Metav Werkzeuge or consult our specialists if clarification is required. Thread milling cutter DC207TM — for S12, S14, S21, S30 and S40 indexable inserts; Ø21 mm, 20 mm shank — Teknik Makina A Thread milling cutter DC207TM engineered for versatile thread generation in CNC machining, compatible with a wide range of indexable inserts for flexible shop-floor use Compatible with S12–S40 indexable inserts 21 mm diameter for compact threading 20 mm shank for secure tool holding Minimise tooling stock while keeping capability flexible This cutter is built around broad insert compatibility, accepting S12, S14, S21, S30 and S40 indexable inserts, which reduces the need for multiple dedicated tools and simplifies inventory management. By using standard insert sizes, the tool enables cost-efficient regrinding or replacement and fast adaptation to different thread forms. The modular nature of the system supports uninterrupted production planning and contributes to a predictable parts flow, improving overall process economy without compromising machining versatility. Secure clamping and reliable insert retention for stable cycles A 20 mm shank provides a robust connection to standard tool holders, improving concentricity and reducing vibration during thread milling operations. Insert fixation is secured with an M4x10 Torx screw, tightened with a T15 key, ensuring consistent clamping force and straightforward maintenance procedures. These attributes support repeatable performance over long production runs, which is especially important for operations that prioritise dimensional consistency and surface finish. Compact diameter with practical handling for precise results With a Ø21 mm cutting head and a total length of 94 mm, the cutter balances rigidity and accessibility for restricted or multi-axis setups. The compact diameter helps maintain tool stiffness close to the cutting zone, reducing deflection when generating threads, while the overall length keeps overhang to a minimum. In practice, this design translates into improved precision and more predictable thread geometry, making the tool suitable for demanding manufacturing tasks where tolerances and surface integrity matter. Integration into workshop workflows and tool management The cutter's support for common insert formats and straightforward fastenings simplifies changeover and tool pre-setting. This eases logistic planning for maintenance teams and reduces spindle downtime during insert changes. The machining strategy benefits from the cutter's geometry when combined with appropriate CAM programming; the result is efficient chip control, repeatable thread profiles and predictable cycle times — all factors that support higher throughput and less rework on the shop floor. For reliable, high-precision thread milling with broad insert compatibility, request the Teknik Makina DC207TM via Metav Werkzeuge — technical advisors in Emmerich are ready to assist at info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: DC207TM Manufacturer: Teknik Makina Numbers / core technical data Diameter: 21 mm Overall length: 94 mm Shank diameter: 20 mm Torx screw: M4x10 Torx key: T15 Designs / special features For S12, S14, S21, S30 and S40 indexable inserts Compatible with standard tool holders requiring 20 mm shank Compact 94 mm overall length for reduced overhang Manufacturer: Teknik Cutting Tools; Teknik Makina product designation DC207TM FAQ Which insert sizes fit this cutter? The cutter accepts S12, S14, S21, S30 and S40 indexable inserts, allowing flexible selection of grades and geometries for different thread requirements. What is the shank diameter and why does it matter? The tool has a 20 mm shank; a larger shank diameter improves clamping stability and reduces deflection for more consistent thread profiles. How are the inserts secured? Inserts are fastened using an M4x10 Torx screw, tightened with a T15 key, providing straightforward and reliable insert retention. Is this cutter suitable for multi-axis CNC machines? The cutter’s compact Ø21 mm diameter and 94 mm overall length make it well suited to multi-axis setups where limited clearance and rigidity are considerations. Can the cutter be used for different thread forms? Yes — by selecting appropriate indexable inserts and CAM parameters, the cutter can generate a range of thread geometries while easing shop-floor tooling logistics. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com
23mm S16Q SD-CR Drill Rod 32mm Cutting Height, 62.5° Cutting Angle - Teknik Makina
Take advantage of a compact, high-stability boring solution with a 16 mm shank and a 23 mm cutting diameter, compatible with DC-- 11T3 indexable inserts; order directly via Metav Werkzeuge or request advice from our technical consultants. S16Q SD-CR boring bar — compact indexable-insert boring bar, 16 mm shank, for DC-- 11T3 inserts (Teknik Makina) The S16Q SD-CR is a right-hand boring bar intended for internal turning with DC-- 11T3 indexable inserts, offering a compact 180 mm overall length for confined setups. S16Q SD-CR ISO shank for secure clamping 16 mm shank diameter for stable machining Compatible with DC-- 11T3 indexable inserts Right-hand cutting with 62.5° cutting angle Stable cutting for precise internal turning The bar provides stable clamping through a standard ISO shank design, which reduces chatter and improves surface finish in internal turning operations. A 16 mm shank and modest mass (0.288 kg) help maintain rigidity while allowing flexible setup in smaller machining centres. The 23 mm cutting diameter gives a clear indication of effective working size, and the geometry is designed to promote predictable cutting behaviour under steady feeds and speeds. This combination supports higher first-pass accuracy and fewer reworks, translating into measurable time and cost savings in production runs. Optimised for fast insert changes and consistent chip control Compatibility with DC-- 11T3 inserts means quick, repeatable insert replacement without complex regrinding. The SD-CR holder form and the 62.5° cutting angle are chosen to balance cutting forces and tool accessibility, delivering consistent chip formation and predictable load distribution. Right-hand cutting direction simplifies toolpath planning for common CNC lathe setups and reduces the learning curve for operating personnel. For teams new to indexable tooling, this arrangement shortens setup time and lowers the risk of mounting errors. Compact design that fits busy workshops With an overall length of 180 mm and a cutting height of 32 mm, this boring bar is designed for confined tool pockets and tight turret clearances. The reduced overhang curtails vibration and contributes to stable surface finishes when machining internal diameters. At only 0.288 kg, the tool is lightweight to handle but maintains the necessary mass for damping unwanted motion. The compact footprint makes the tool a practical choice for small-batch production or mixed-workshop environments where machine real estate and quick changeovers are priorities. If specific application parameters need verification, our technical team is available for guidance at info@metav-werkzeuge.com or by phone on +49 2822 7131930. Contact Metav Werkzeuge for application advice on the Teknik Makina S16Q SD-CR boring bar (SKU K172TM) and arrange prompt delivery from Emmerich with tailored technical support Technical data Article number: K172TM Manufacturer: Teknik Makina ISO designation: S16Q SD-CR Type designation (English): SD-CR for DC-- Indexable Inserts Brand: Teknik Makina Numerical data Shank diameter: 16 mm Cutting diameter: 23 mm Overall length: 180 mm Cutting height: 32 mm Weight: 0.288 kg Cutting angle: 62.5° Cutting direction: right Compatibility & features For indexable inserts: DC-- 11T3 Clamp/holder reference: 11 Suitable for internal turning with indexable inserts ISO shank holder format FAQ Which insert type fits this boring bar? The boring bar is designed for DC-- 11T3 indexable inserts; the SD-CR holder form accepts inserts in that size and seating form. What are the dimensional key figures of the tool? The tool has a 16 mm shank, a 23 mm cutting diameter and an overall length of 180 mm; weight is 0.288 kg (SKU K172TM). Is the cutting direction right- or left-handed? This model is configured for right-hand cutting and a 62.5° cutting angle suited to common internal turning operations. How does the compact length benefit small workshops? A shorter overhang reduces vibration and improves stability in confined setups, allowing more consistent surface finishes and safer tool changeovers. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
23mm S16Q SDZCR Drilling Bar 5° Cutting Angle, Right-Hand For DC-- 11T3 Indexable Inserts - Teknik Makina
Take advantage of the combination of rigid 16 mm shank construction, 180 mm overall length for extended reach and direct compatibility with DC-- 11T3 indexable inserts for efficient, repeatable external turning; order the tool via Metav Werkzeuge or contact our consultants for application advice. S16Q SDZCR Boring Bar — 16 mm shank, 180 mm overall length (Teknik Cutting Tools) S16Q SDZCR Boring Bar designed for right-hand external turning applications with DC-- 11T3 indexable inserts Right-hand cutting for external turning 16 mm shank for compact toolholders Compatible with DC-- 11T3 indexable inserts 180 mm overall length for extended reach Precise performance for production turning The S16Q SDZCR is engineered as a compact, rigid boring bar that balances reach and stiffness for consistent turning operations. With a 16 mm shank and an 180 mm overall length, the tool provides access to deeper bores and external features while maintaining stability. The modest 5° cutting angle reduces radial cutting forces, which helps to extend insert life and improve surface finish. For workshops seeking predictable cycle times, this combination supports efficient, repeatable results on typical turning centres. Inventory efficiency and insert compatibility This tool accepts DC-- 11T3 indexable inserts, simplifying tooling management across a production line. Using common insert formats reduces the need for specialised stocks and enables faster changeovers; spare inserts and compatible grades are widely available for varied materials. The 25 mm cutting height ensures correct seating of the insert, thereby maintaining tool geometry and cutting accuracy. The result is a practical compromise between flexibility and low total tooling cost in small-batch and serial production environments. Practical handling and workshop benefits Weighing 0.302 kg, the bar is light enough for easy handling yet solid in service. The nominal 23 mm diameter at the cutting head and the defined shaft geometry support secure clamping in standard toolholders. Right-hand cutting orientation is specified for conventional turning setups. For engineers and technicians, this means straightforward integration into existing tool plans without additional setup complexity, allowing shortened machine downtime and predictable process behaviour. For robust right-hand external turning with proven insert compatibility, contact Metav Werkzeuge for purchasing and technical guidance on the S16Q SDZCR boring bar — email info@metav-werkzeuge.com or call +49 2822 7131930. Technical data Article number: K192TM Manufacturer: Teknik Makina ISO designation: S16Q SDZCR Facts Shaft diameter: 16 mm Cutting height: 25 mm Overall length: 180 mm Head diameter: 23 mm Weight: 0.302 kg Cutting angle: 5° Cutting direction: right Compatibility & features For indexable inserts: DC-- 11T3 Suitable for right-hand external turning Compact design for standard toolholders FAQ What insert type does this boring bar use? The S16Q SDZCR boring bar is designed for DC-- 11T3 indexable inserts, which are a common format for external turning and provide easy replacement. Is the tool suitable for deep external features? Yes, the 180 mm overall length of the bar gives added reach for deeper external turning and features where standard-length holders may be insufficient. Which cutting direction is supported by the bar? This bar is configured for right-hand cutting, compatible with conventional turning operations on lathes and turning centres. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
24.5mm Thread Tapping Bar for Internal Threads Right-Hand, Solid Carbide, Internal Coolant - Teknik Makina
Combine solid‑carbide durability, internal coolant and precise indexable‑insert compatibility to achieve consistent, high‑quality internal threads in production and toolroom environments. Order the KE78TM thread boring bar directly via Metav Werkzeuge or ask our consultants for application guidance. KE78TM Thread Boring Bar — Solid‑carbide tool with internal coolant (Teknik Makina) The KE78TM thread boring bar is a purpose‑built tool for producing internal threads with indexable inserts; it suits CNC turning centres and dedicated threading stations where rigidity and coolant delivery are required. Solid carbide construction Internal coolant feed Compatible with 22 IR inserts Right‑hand cutting, ISO E20S Precision that keeps production running The monoblock solid carbide construction delivers high stiffness and dimensional stability under load, reducing chatter and prolonging tool life compared with less rigid designs. Built to accept the 22 IR indexable system, the bar transfers cutting forces cleanly through the holder and into the machine spindle, which translates into repeatable thread form accuracy and fewer rework cycles. The ISO designation E20S indicates a standardised interface for secure location and predictable performance in automated setups. Consistent coolant control for better chip evacuation An integrated internal coolant channel provides directed fluid delivery straight to the cutting zone, aiding chip control and temperature management during the threading operation. This targeted cooling reduces built‑up edge and thermal distortion, improving surface finish and thread consistency across long production runs. For operations where cycle time and first‑pass yield matter, the combination of internal coolant and carbide rigidity supports higher metal removal stability and reduced cycle‑to‑cycle variance. Secure clamping and serviceable components The bar is prepared for the IR22 clamping system and secures inserts with the supplied Torx fastenings (Torx T15 screws and M4x11 fixing screws), ensuring reliable insert retention under intermittent thread depths and interrupted cuts. The E20S shank form and 20 mm shank diameter provide compatibility with common toolholders while the 15.6 mm cutting height affords proper insert engagement for standard internal thread profiles. These mechanical details simplify setup and replacement procedures, limiting downtime between tool changes. Designed for industrial threading tasks With an overall length of 250 mm and a body diameter of 24.5 mm, the bar is engineered for balance between access into bores and the stiffness required for accurate internal profiling. Right‑hand cutting geometry suits standard turning and threading directions prevalent in most machine tool operations. The KE78TM is therefore appropriate for series production and maintenance tasks where a robust, repeatable threading solution is required, and where the economy of indexable inserts brings measurable savings over time. Contact Metav Werkzeuge for tailored application advice on the Teknik Makina KE78TM thread boring bar — Metav’s specialists in Emmerich can confirm compatibility with existing holders and machining parameters; eMail info@metav-werkzeuge.com, Tel +49 2822 7131930 Technical data Article number: KE78TM Manufacturer: Teknik Makina Product: Thread boring bar for inside thread Diameter: 24.5 mm Total length: 250 mm Shank diameter: 20 mm Cutting height: 15.6 mm Weight: 0.57 kg Cutting direction: Right Material: Solid carbide Indexable insert system: 22 IR Clamping holder designation: IR22 ISO designation: E20S Internal coolant: Yes Torx screw: T15 and M4x11 FAQ Which machines is this bar suited for? The KE78TM thread boring bar from Teknik Makina is intended for use on CNC turning centres and compatible threading stations where an E20S shank and IR22 clamping system can be accommodated. Which insert type is required for operation? This bar accepts 22 IR indexable inserts; secure the inserts with the specified Torx fasteners (T15 and M4x11) to maintain correct seating and cutting geometry. Is coolant delivery supported and why does it matter? Yes — the KE78TM features internal coolant to direct fluid to the cutting edge, improving chip evacuation, heat control and surface finish during internal threading. What are the main benefits of the solid‑carbide body? The solid‑carbide construction increases rigidity and wear resistance, helping to preserve thread form accuracy and extend service intervals compared with less rigid tool bodies. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com
24mm 95° Drilling Bar PCLN for CNMG Indexable Inserts With Internal Coolant - Teknik Makina
Benefit from the combination of precise 95° cutting geometry and integrated internal coolant for consistent metal removal and extended tool life. Compatibility with CNMG 1204 indexable inserts plus a robust Ø20 mm shank delivers secure clamping and dimensional stability in production environments. Order the boring bar directly via Metav Werkzeuge or consult our specialists if required. A20R PCLNR boring bar — PCLN for CNMG indexable inserts, internal coolant (Teknik Makina) The A20R PCLNR boring bar is a right‑hand tool engineered for finishing and bore‑facing operations, featuring internal coolant and an ISO A20R PCLNR designation for CNMG‑type indexable inserts. 95° cutting angle for stable cutting Internal coolant for improved tool life Compatible with CNMG 1204 inserts Shank Ø20 mm, overall length 200 mm Precise geometry for dependable chip control and surface finish The 95° cutting angle and PCLN geometry combine to provide a stable cutting action that reduces vibration and promotes predictable chip formation. For practical use this means fewer interrupted cuts and a more consistent surface finish when machining bores or facing close tolerances. The tool accepts CNMG 1204 indexable inserts, a common industry standard; these inserts allow the machining parameters to be adapted by selecting the appropriate grade and geometry for the workpiece material. By pairing a proven insert form with the bar’s right‑hand configuration, the assembly is optimised for finishing passes where dimensional accuracy and repeatability are priorities. Internal coolant for thermal control and longer tool life An integral coolant channel delivers lubricant and coolant directly to the cutting zone, which helps to evacuate heat and improve chip flow. This internal coolant arrangement reduces thermal distortion of the tool and workpiece, supporting longer tool life and a more consistent bore diameter over extended runs. In production scenarios where cycle time and part quality matter, targeted coolant supply reduces the need for frequent tool inspection and tempering of cutting data. The result is a lower total cost of operation through fewer tool changes and improved process stability. Robust design for secure clamping and easy integration With a Ø20 mm shank and an overall length of 200 mm, the bar offers a balance between rigidity and reach for typical centre‑lathe and CNC turret set‑ups. The ISO designation A20R PCLNR identifies the toolholder form, simplifying tool‑room inventory and ensuring compatibility with standard clamping systems. A modest mass (approx. 0.52 kg) supports rapid accelerations without compromising stability. In practice, this means reliable performance in mixed‑batch work and easier handling during tool changes; the combination of solid geometry and internal coolant makes the tool suitable for high‑precision finishing operations where consistent results are required. Contact Metav Werkzeuge for tailored technical advice and assured supply from Emmerich — quote SKU AP338TM when enquiring for faster processing Technical Data Article number: AP338TM Manufacturer: Teknik Makina ISO designation: A20R PCLNR Type: PCLN for CNMG indexable inserts Special feature: with Coolant Facts Shank diameter: 20 mm Diameter: 24 mm Overall length: 200 mm Cutting height: 50 mm Cutting angle: 95° Weight: 0.52 kg Cutting direction: right Special features Internal coolant supply Compatible with CNMG 1204 inserts ISO form: A20R PCLNR Suitable for finishing and bore operations FAQ Which insert type fits this boring bar? The boring bar is designed for CNMG 1204 indexable inserts; the PCLN geometry is matched to that insert form for stable seating and secure clamping. Does the bar provide coolant directly to the cutting edge? Yes — the tool features internal coolant that delivers fluid to the cutting zone, supporting thermal control and improved chip evacuation. What are the shank and overall dimensions? Shank Ø is 20 mm with an overall length of 200 mm, providing a balance of rigidity and reach for typical lathe and turret installations. Is this tool suitable for heavy roughing or finishing? The design and 95° cutting angle are optimised for finishing and bore‑facing operations; for heavy roughing a more rigid, larger‑section holder may be preferable. How is the tool identified in ISO form? The bar carries the ISO designation A20R PCLNR, which helps with tool selection and ensuring compatibility with standard clamping systems. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
24mm A20R PCLNL Boring Bar PCLN For CNMG Indexable Inserts With Coolant, Left-Hand 200mm Shaft - Teknik Makina
Benefit from a combination of robust shank stability, integrated internal coolant and compatibility with CNMG 1204 indexable inserts for consistent turning performance; order directly via Metav Werkzeuge or consult the technical team for application-specific advice. A20R PCLNL Boring Bar (PCLN for CNMG indexable inserts) by Teknik Makina — left‑hand, internal coolant The A20R PCLNL boring bar is a purpose-built external turning holder compatible with CNMG 1204 indexable inserts, offering a left‑hand cut orientation and integrated internal coolant to support reliable chip evacuation and extended tool life. Compatible with CNMG 1204 indexable inserts Internal coolant for improved chip control Left‑hand cutting orientation for reverse cuts 20 mm shank, 200 mm overall length Consistent rigidity and predictable machining results The A20R PCLNL boring bar is engineered to combine a compact 20 mm shank with a 200 mm overall length, delivering a balance between accessibility and stability for medium‑reach turning tasks. The cylindrical shank and the holder geometry contribute to reduced vibration and improved surface finish, which translates into fewer re‑works and higher first‑pass yields. For workshop managers seeking measurable productivity gains, the holder’s construction supports reproducible set‑ups and steady cutting conditions across batches. Better cooling and chip management for longer cutting windows Equipped with internal coolant, the tool channels cutting fluid directly to the insert seating area to manage temperatures and assist chip evacuation during continuous operations. This targeted coolant supply reduces thermal load on both insert and workpiece, which helps maintain dimensional accuracy and extends insert life. In practice, internal coolant reduces the frequency of tool changes and supports uninterrupted production runs when paired with appropriate CNMG inserts. Straightforward compatibility with standard indexable inserts Designed specifically for the PCLN pocket form, the holder accepts CNMG 1204 indexable inserts, enabling quick insert changes and broad grade selection for different materials. The PCLN style secures the insert at an angle that supports predictable cutting geometry and repeatable results. For procurement teams, this compatibility simplifies stock management: a single holder design works with widely available CNMG inserts from multiple suppliers. Suited to industrial workflows and mixed‑material applications With a 95° cutting angle, the holder is optimised for robust metal engagement and can be integrated into standard lathe tool posts without special adapters. The combination of left‑hand orientation and the holder’s geometry suits reverse‑hand operations or setups where tooling access is constrained. The moderate weight of 0.52 kg makes handling and index changes straightforward for operators, while the tool’s dimensions facilitate close‑quarter turning tasks in production environments. Contact Metav Werkzeuge for application recommendations and direct supply from Emmerich — info@metav-werkzeuge.com | +49 2822 7131930 Technical data Article number: AP348TM Model: A20R PCLNL Manufacturer: Teknik Makina SKU: AP348TM Facts Shank diameter: 20 mm Overall length: 200 mm Diameter: 24 mm Cutting height: 50 mm Weight: 0.52 kg Cutting angle: 95° Special features Compatibility: CNMG 1204 indexable inserts Internal coolant: yes Cutting direction: left Pocket style: PCLN Feature: with coolant FAQ What inserts fit this holder and how are they mounted? The holder accepts CNMG 1204 indexable inserts; inserts are clamped into the PCLN pocket form and secured with the standard clamping screw, ensuring consistent seating for repeatable cutting. Is the coolant supplied through the bar or externally? This boring bar features internal coolant that directs fluid to the insert area; the integrated supply supports temperature control and chip management for prolonged cutting intervals. Can the bar be used for light‑ and medium‑duty turning operations? Yes, the A20R PCLNL holder from Teknik Makina is intended for light to medium turning tasks where a 20 mm shank and 200 mm reach provide the required stability and access. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
24mm Drilling Bar S20Q STIR STI For IR/ER Indexable Inserts 40mm Cutting Height, 20mm Shank Diameter - Teknik Makina
Take advantage of the combination of compact design, precise dimensions and compatibility with standard indexable inserts to reduce overhang, improve surface finish and keep clamping reliable; order the tool through Metav Werkzeuge or contact our consultants for application advice. S20Q STIR boring bar — STI for IR/ER indexable inserts (right-hand) S20Q STIR is a right-hand boring bar designed for internal turning with IR/ER indexable inserts, suited to workshops and production lines requiring stable clamping and predictable chip control Right-hand boring bar for IR/ER indexable inserts 24 mm head diameter, 20 mm shank 180 mm overall length, 40 mm cutting height Precision that reduces vibration and improves surface finish The bar’s compact 180 mm overall length and reduced overhang support a more stable cutting setup, which directly lowers vibration and enhances surface quality. The combination of a 20 mm shank and a 24 mm head diameter helps maintain rigidity in the holder; this is particularly beneficial for internal turning where overhang can compromise tolerances. Fewer vibrations mean longer life for inserts and smoother production runs, which translates into less rework and improved first-pass yield. Built for standard indexable inserts and straightforward handling Compatibility with IR/ER indexable inserts — specified here as 22 IR — allows fast insert changes and consistent seating in the clamping system. The tool’s ISO designation S20Q STIR signals standardised interfaces, making it straightforward to match with existing clamping holders such as the IR22 designation. Right-hand cutting orientation supports conventional turning operations and predictable chip flow, simplifying programming and setup on conventional lathes and multi-tasking machines. Practical dimensions and balanced weight for workshop efficiency The tool’s 40 mm cutting height provides sufficient engagement for typical internal turning tasks while keeping the assembly compact. At approximately 0.431 kg, the bar offers an advantageous balance between mass and manoeuvrability, aiding quick tool changes without compromising stability. These tangible dimensions support predictable run-out and repeatability, making the component a pragmatic choice for production environments that prioritise uptime and consistent part quality. For recommendations on integrating the S20Q STIR into existing toolholders, or to secure supply from Metav Werkzeuge, contact Metav Werkzeuge for tailored advice and dependable delivery from Emmerich Technical Data Article number: K358-1TM SKU: K358-1TM Facts Diameter: 24 mm Shank diameter: 20 mm Cutting height: 40 mm Overall length: 180 mm Weight: 0.431 kg Cutting direction: right Special features ISO designation: S20Q STIR Compatible inserts: 22 IR Clamping holder designation: IR22 Intended for IR/ER indexable inserts FAQ What inserts are compatible with this boring bar? The bar is compatible with IR/ER indexable inserts, specifically suited to the 22 IR insert format used with the S20Q STIR (SKU K358-1TM). Is the cutting orientation right-hand or left-hand? This tool is made for right-hand cutting, which matches standard turning directions on most lathes and multi-tasking centres. Which clamping holder fits the bar? The bar is specified alongside clamping holder designation IR22, enabling secure seating and repeatable clamping. Can the S20Q STIR be used in high-speed applications? Performance at high spindle speeds depends on machine setup and insert grade; the S20Q STIR provides a rigid platform that supports higher-speed cuts when paired with suitable inserts and correct clamping. What are the key dimensions to check before ordering? Verify the 24 mm head diameter, 20 mm shank, 180 mm overall length and 40 mm cutting height to ensure compatibility with the toolholder and the available machine envelope. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com
24mm S20Q TTIR Boring Bar 40mm Cutting Height for 16 IR Indexable Inserts, Right-Hand - Teknik Makina
Take advantage of the combination of high rigidity, straightforward insert compatibility and compact dimensions for reliable internal machining. Order the boring bar directly via Metav Werkzeuge or consult the technical team for tailored advice. Boring bar S20Q TTIR – Right‑hand toolholder with 20 mm shank for IR16 indexable inserts (Teknik Makina) The boring bar S20Q TTIR is a right‑hand toolholder designed for internal machining with 16 IR indexable inserts, offering a compact 180 mm overall length for tight set‑ups. S20Q TTIR ISO designation 20 mm shank diameter 180 mm overall length For 16 IR indexable inserts Engineered for consistent internal machining and rigidity The S20Q TTIR is built to deliver consistent internal machining where stability matters. With a 20 mm shank and a 180 mm overall length the bar minimises overhang while maintaining tool rigidity, which reduces vibration and improves surface quality. The 40 mm cutting height gives a secure seating for the insert, allowing precise tool positioning in confined bores. This construction supports predictable tool life and repeatable results in production runs. Compatible with industry indexable inserts for fast changeovers Designed for use with IR16 indexable inserts and the matching clamp system, the holder accepts the TA060 locating plate and the BSP010 washer for secure clamping. Compatibility with common insert geometries means quick, low‑skill insert replacement and minimal machine downtime. The right‑hand cutting orientation ensures the correct chip flow direction for standard internal turning applications, enabling efficient swarf evacuation and smoother cutting cycles. Fewer process interruptions through straightforward system integration Integration into existing tool inventories is straightforward: the bar’s ISO designation and common accessory interfaces reduce procurement complexity and spare‑part variety. By standardising on a compact, indexable system, workshop logistics are simplified and maintenance routines are faster. Coupled with Metav’s steady supply chain and technical backing, the toolholder supports uninterrupted production and easier planning for replacement inserts and clamping parts. For procurement or technical clarification on the Teknik Cutting Tools S20Q TTIR boring bar (SKU K338TM), contact Metav Werkzeuge for a supply recommendation or compatibility check at info@metav-werkzeuge.com or call +49 2822 7131930 Technical Data Article number: K338TM Manufacturer: Teknik Makina ISO designation: S20Q TTIR Secondary designation: SIR for IR Indexable Inserts SKU: K338TM Core dimensions Overall length: 180 mm Shank diameter: 20 mm Cutting height: 40 mm Weight: 0.445 kg Diameter: 24 mm Compatibility / Special features For indexable inserts: 16 IR Clamping insert holder: IR16 Locating plate: TA060 Pass washer: BSP010 Cutting direction: right FAQ Which inserts fit this toolholder? The S20Q TTIR boring bar (Teknik Cutting Tools, SKU K338TM) is specified for 16 IR indexable inserts and uses the TA060 locating plate with BSP010 washer for secure clamping. What are the main dimensions to check for machine setup? Key dimensions are a 20 mm shank diameter and 180 mm overall length; the cutting height is 40 mm, and the tool weight is 0.445 kg. Is the cutting direction standard or reversed? This toolholder has a right‑hand cutting direction, suitable for conventional internal turning operations where clockwise tool engagement is required. How does the design reduce downtime? Compatibility with standard IR16 inserts and common clamping parts enables fast insert changes and simpler spare‑part management, reducing machine downtime during routine maintenance. Which accessories are referenced for correct mounting? The bar is intended to be used with the TA060 locating plate and BSP010 pass washer together with the IR16 clamping system for correct seating and secure clamping. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com
24mm S20R PCLNR Boring Bar 200mm, For CNMG 1204 Inserts, Left-Hand Without Coolant - Teknik Makina
Efficient left-hand turning with CNMG 1204 indexable inserts and a 20 mm shank delivers stable cutting and simple insert changes; the coolant-free design avoids the need for internal coolant systems and eases maintenance. Order the boring bar directly via Metav Werkzeuge or ask our consultants if needed. Boring bar — PCLN for CNMG indexable inserts, left-hand, 20 mm shaft (Teknik Makina) A compact boring bar designed for left-hand turning operations with CNMG 1204 indexable inserts, suitable where internal coolant is not required. Left-hand cutting direction For CNMG 1204 indexable inserts 20 mm shank diameter, 200 mm overall length No internal coolant required Stable cutting performance for left-hand turning The PCLN geometry combined with compatibility for CNMG 1204 inserts provides a balance of rigidity and accessibility for internal and external facing operations. The 20 mm shank offers a rigid mounting that reduces chatter and enhances surface finish, while the slightly larger 24 mm diameter at the cutting head improves stability. With a 95° cutting angle, the tool is suited to precise finishing cuts where dimensional accuracy matters. These characteristics translate into fewer reworks and steadier cycle times on production runs. Fast insert changes and secure clamping Specified to ISO as S20R PCLNR, the bar accepts standard CNMG indexable inserts, enabling quick insert replacement and compatibility with common insert grades. The standardised interface reduces setup time and inventory complexity, because compatible inserts and toolholders are widely available. The secure insert pocket and robust seat design ensure repeatable clamping, which supports consistent tool life and predictable machining results for batch work and single-piece manufacturing alike. Practical design to keep workshops productive At a 200 mm overall length and weighing 0.54 kg, the tool is compact enough for tight set-ups while providing sufficient reach for many turning tasks. The combination of shaft and head dimensions allows use with a wide range of holders designed for a 20 mm shank, reducing the need for special adaptors. The resulting ease of integration and minimal maintenance requirements help to lower machine downtime and simplify tool management in busy shops. Dry-ready operation for specific process requirements Designed without internal coolant, the bar is intended for processes that use external cooling, dry machining strategies, or where internal coolant is unnecessary or undesirable. The left-hand cutting orientation matches machines and operations that require counter-direction cutting, keeping process flows consistent. Choosing a coolant-free tool can simplify machine plumbing and reduce potential points of failure, while still delivering reliable cutting performance when paired with the appropriate insert grade. For technical advice or to secure this Teknik Makina boring bar from Metav Werkzeuge’s Emmerich stock, contact Metav Werkzeuge by eMail: info@metav-werkzeuge.com or by phone: +49 2822 7131930 to discuss suitability and availability Technical data Article number: P348TM Manufacturer: Teknik Makina ISO designation: S20R PCLNR Designation (EN): PCLN for CNMG indexable inserts Core dimensions Shank diameter: 20 mm Cutting height: 50 mm Overall length: 200 mm Diameter: 24 mm Weight: 0.54 kg Cutting angle: 95° Special features Left-hand cutting direction Without internal coolant For CNMG 1204 indexable inserts SKU: P348TM FAQ Is this bar compatible with standard CNMG insert grades? Yes. The boring bar is designed for CNMG 1204 indexable inserts and works with standard CNMG grades suited to the machining task. Can the bar be used where internal coolant is required? No. This model is supplied without internal coolant, so operations requiring through-tool coolant need an alternative tool with internal coolant provision. What does the ISO designation S20R PCLNR tell me? The S20R PCLNR ISO code indicates the shank and insert seat geometry, ensuring compatibility with holders and inserts that match that specification. Is the 20 mm shank suitable for common toolholders? Yes. The 20 mm shank conforms to common holder sizes, allowing straightforward installation in standard toolholders used in many workshops. Does the left-hand orientation affect setup on the lathe? Left-hand cutting direction means the tool is intended for counter-direction turning operations; check machine and programme orientation to ensure correct mounting of the bar. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com
24mm SIL S20Q Boring Bar for 16-22ER Indexable Inserts 40mm Cut Height, 20mm Shank - Teknik Makina
Take advantage of the proven combination of left-hand cutting, 20 mm shank diameter and compatibility with 16–22ER indexable inserts for steady internal turning performance; order the SIL S20Q directly via Metav Werkzeuge or ask our consultants if needed SIL S20Q boring bar — 20 mm shank, left-hand cutting — Teknik Makina The SIL S20Q is a left-hand boring bar designed for 16–22ER indexable inserts, intended for internal turning and facing operations in workshop and production environments Left-hand cutting direction 20 mm shank diameter Compatible with 16–22ER indexable inserts 180 mm overall length Stable left-hand machining for repeatable accuracy The SIL S20Q is engineered for consistent performance in left-hand operations, making it suitable where reverse-direction cutting is required. The combination of the 20 mm shank and a 24 mm diameter body provides rigidity that reduces deflection during internal turning. This rigidity translates into improved surface finish and repeatability on serial parts, helping to maintain production tolerances and reduce scrap. Secure clamping and insert compatibility for reduced downtime Designed to accept 16–22ER indexable inserts and to interface with an ER16 clamping system, the tool offers straightforward insert changes and reliable seat stability. The 40 mm cutting height ensures adequate engagement for common insert sizes, while the robust clamping arrangement minimises vibration and the need for frequent re-adjustment, resulting in fewer interruptions on the shop floor. Optimised length and balance for workshop efficiency With a 180 mm overall length and a mass of approximately 0.445 kg, this boring bar balances reach and controllability for internal operations. The geometry has been conceived to assist chip control and steady cutting behaviour, which contributes to longer insert life and lower tooling costs per part. The tool’s dimensions support setups where access and rigidity must be reconciled without resorting to oversized holders. Practical handling and service considerations The bar’s ISO designation SIL S20Q and clear mechanical specification simplify tool selection for engineering teams and purchasing. Routine checks of clamping screws and insert seating are recommended to preserve cutting stability and tool life. If requirements are unclear or a specific machining task demands verification, Metav’s technical advisors are available to clarify compatibility and to recommend optimal insert grades and feeds For reliable left-hand internal turning with proven compatibility, contact Metav Werkzeuge for tailored technical advice and ordering; call +49 2822 7131930 or email info@metav-werkzeuge.com Technical data SKU: K330TM Manufacturer: Teknik Makina ISO designation: SIL S20Q Item description: Boring bar for indexable inserts (SIL for 16–22ER) Facts Shank diameter: 20 mm Overall length: 180 mm Body diameter: 24 mm Cutting height: 40 mm Weight: 0.445 kg Cutting direction: left Special features Compatible with 16–22ER indexable inserts ER16 clamping interface Designed for internal turning and facing Left-hand boring bar FAQ Which insert sizes are supported? The tool accepts 16–22ER indexable inserts; the SIL S20Q is specified for that range and seats ER-style cutters securely. What is the shank diameter and overall length? The boring bar has a 20 mm shank diameter and an overall length of 180 mm, providing a balance between reach and rigidity. Is the cutting direction left- or right-handed? This boring bar is configured for left-hand cutting, indicated by the tool geometry and ISO designation. Which clamping system is compatible? The bar interfaces with an ER16 clamping system, allowing straightforward integration into compatible toolholders. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
Achieve exact bores with a boring bar with internal coolant
A boring bar with internal coolant is a specialised tool for internal machining on lathes and machining centres, designed to enlarge and finish existing holes to precise dimensional and form tolerances. Also referred to as an internal coolant boring bar or coolant‑fed boring bar, this tool class routes coolant through the tool body so that cutting edges are supplied directly with fluid under pressure.
How internal coolant keeps deep and blind bores reliable
When machining with external coolant only, the fluid is delivered from outside via machine nozzles and often fails to reach the cutting zone in longer bores, leaving chips trapped and increasing thermal load. A boring bar with internal coolant contains axial coolant channels that run through the tool shank to the cutting edge, delivering high‑pressure coolant where it is needed. This arrangement is essential for machining deep bores, blind holes and for materials that produce long, continuous chips; it lowers local temperatures, flushes chips out of the bore and reduces the risk of tool breakage and surface damage.
Key advantages that improve productivity
- Faster cycle reliability: internal coolant reduces thermal distortion and helps maintain tight tolerances over longer runs.
- Improved chip evacuation: pressurised coolant clears chips from the cutting zone, preventing chip clogging and re-cutting.
- Extended tool life: cooler cutting edges and effective flushing reduce wear and the likelihood of catastrophic tool failure.
- Process versatility: suitable for deep bores and blind holes, especially in difficult‑to‑machine or long‑chipping materials.
Metav as the practical partner for precision tooling
Metav stands for the democratisation of precision and is positioned as a pragmatic partner for industry and workshops. Based in Emmerich, Metav combines hands‑on technical expertise with a broad supply range: over 250,000 products and a proven track record with more than 48,000 customers, ensuring steady availability and a quality filter for the European market. For buyers seeking coolant‑fed solutions, Metav offers curated assortments and selection guidance for boring bars with internal coolant.
In summary, a boring bar with internal coolant delivers targeted cooling and chip control that is indispensable for deep and blind bores, improving tolerance control, tool life and process stability.
FAQ
When should a boring bar with internal coolant be chosen over external coolant?
Select a boring bar with internal coolant whenever bores are deep or blind, or when machining hard‑to‑cut or long‑chipping materials; the internal coolant ensures reliable chip evacuation and temperature control where external coolant cannot reach.
How do axial coolant channels reduce the risk of tool breakage?
Axial coolant channels feed high‑pressure coolant directly to the cutting edge, lowering thermal stress at the point of generation and flushing chips away, which together reduce flank wear and the chance of sudden tool failure when using a boring bar with internal coolant.
Can internal coolant boring bars be used on both lathes and machining centres?
Yes. The internal coolant design is compatible with standard toolholders used on lathes and machining centres, making the internal coolant boring bar a flexible choice across machine platforms.
Which workpiece materials benefit most from coolant‑fed boring bars?
Materials that produce long, continuous chips or that are prone to thermal softening during cutting—such as certain stainless steels and high‑strength alloys—benefit markedly from the chip flushing and cooling provided by a boring bar with internal coolant.
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com