Carbide indexable inserts for high‑performance metalworking
Carbide indexable inserts are wear‑resistant cutting elements designed to deliver economical, precise material removal across a wide range of workpieces, offering excellent balance between extreme wear resistance and the toughness required to withstand mechanical shocks. Used on toolholders such as cutters, turning tools and twist drills, they enable efficient machining of materials from soft non‑ferrous alloys to high‑strength steels by optimising cutting forces and thermal stability. For standard accessible contours external coolant is often sufficient, while deep holes, heavy cutting or machining of stainless steel and titanium alloys benefit from internal coolant channels to protect the cutting edge, improve chip control and extend insert life. Key advantages include high durability, consistent surface finish and reduced tool changeover times through the use of replaceable indexable inserts, carbide grades and toolholder systems.
6.1mm HSS-G Twist Drill DIN 338 ,short, bright finished, Type N - MetavCUT
Twist Drill MetavCUT Profi Line — Type N, 6.1 mm, HSS‑G, Short, 135°, Bright Finished A short MetavCUT Twist Drill Type N for precise metal Drilling Machine work, optimised for hard materials and high stability. Short design for higher stability HSS‑G material for sharp, clean holes 135° tip angle for hard metals Fully ground shaft for superior runout Conforms to DIN 338 for short drills Greater Stability for Accurate Holes Short design reduces the unsupported length of the cutting tool, which directly improves Stability and reduces deflection during machining. The Short 6.1 mm geometry combined with a Fully Ground shaft leads to higher concentricity and cleaner bores when used in a Drilling Machine. As a result, fewer rework operations are required and hole tolerance is easier to maintain. Faster Penetration in Tough Materials Built from HSS‑G, this Short Type N drill achieves up to 40% faster drilling and requires around 50% less feed force compared with conventional HSS drills under comparable conditions. The 135° tip angle is optimised for harder substrates such as stainless steel and tempered alloys, shortening the initial breakthrough time and lowering axial loads on the machine spindle. Precise Application and Recommended Use Designed for metalworking, the Twist Drill Type N excels in drilling Alloyed and Unalloyed Steel, Cast Steel, Cast Iron and Non‑Ferrous Metals. The shortened spiral length limits chatter and makes this drill particularly suited for precise bench, column and stationary machining where coolant can be applied. For manual handfeeding in a Drilling Machine, the improved stability ensures repeatable centre positioning. Manufacturing Quality and Standards for Reliability Produced to DIN 338 as part of the Profi Line, the drill is delivered with a bright finished surface and a ground flute geometry that gives very sharp cutting edges and excellent runout characteristics. Ground flutes (HSS‑G) provide cleaner chips and a defined cutting geometry, though they can be more brittle than rolled variants and therefore benefit from controlled machining parameters and adequate cooling. Strong recommendation: choose the MetavCUT Profi Line short Twist Drill Type N for demanding metal drilling tasks; for advice on suitability, tool parameters or complementary tooling contact METAV Werkzeuge — expert consultation is available by email at info@metav-werkzeuge.com, by phone at +49 2822 7131930 or via WhatsApp at +49 170 2837271 Designation: Twist Drill Brand: MetavCUT SKU: 48061-FDA Diameter: 6.1 mm Spiral Length: 57 mm Overall Length: 93 mm Tip Angle: 135° Type: Type N Execution: Short Shaft Finish: Fully Ground Material: HSS‑G Colour: Bright Finished Model Series: Profi Line Application: Drills for metal Standard: DIN 338 For Drilling Machine: Drilling Machine Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What materials can the MetavCUT Twist Drill Type N be used on? The MetavCUT Twist Drill Type N is primarily specified for metalworking and is suitable for alloyed and unalloyed steel, cast steel, cast iron, sintered iron and non‑ferrous metals; its HSS‑G construction and 135° tip make it particularly effective on harder materials. Is the MetavCUT Twist Drill Type N suitable for handheld drilling? The short configuration and fully ground shaft of the MetavCUT Twist Drill Type N improve stability and centring, so it can be used in hand drilling applications, but best results are achieved with a stationary Drilling Machine and appropriate coolant to avoid undue stress on the tool. For what is a Twist Drill used? A Twist Drill is mainly applied when machining high‑strength materials and larger hole diameters. This form is easy to regrind and withstands higher loads while maintaining good cutting performance. Which 3 drill types exist? The three main drill categories are metal drills, wood drills and masonry/concrete drills. Why are Twist Drills sharpened? Sharpening reduces the cross‑edge at the tip of the Twist Drill, significantly lowering friction and therefore reducing the required feed force; it also improves centring of the tip in the workpiece. Can a metal drill be used in wood? A metal drill can be used in wood, but guidance and finish are usually inferior compared with purpose‑made wood bits; metal drills are easier to regrind and typically have less aggressive self‑feed.
6.25mm HSS Twist Drill DIN 338 ,short, roll forged, black, Type N - MetavCUT
Twist Drill — Type N, 6.25 mm, HSS, short, black, DIN 338 The Twist Drill Type N is a short HSS metal drill designed for stable, precise drilling in steel and other metals using handheld drills or drilling machines. Twist Drill Type N for metal drilling Short HSS design for enhanced stability DIN 338 compliant for short cylindrical drills 118° tip angle for reliable centering Suitable for drilling machines and hand drills Stable performance for demanding metalwork The Twist Drill from MetavCUT combines a short fluted design with HSS material to deliver high rigidity and reduced deflection when drilling into metal. Because the cutter length is reduced relative to standard drills, vibration and runout are minimised, which directly improves hole accuracy and extends tool life. This stability benefits maintenance technicians and workshop professionals who require repeatable centre-to-centre accuracy on metal fabrications. Precise centring and cleaner hole starts A 118° tip angle provides a balanced compromise between initial penetration and centring behaviour, making the drill well suited to typical steels and general metalwork. The geometry lowers the tendency to “walk” on curved or painted surfaces, so fewer pilot holes are needed and setup time is reduced. Users achieve cleaner hole edges and consistent drilling results even when working without elaborate jigs. Standardised dimensions for dependable tooling choices Compliance with DIN 338 ensures the short cylindrical shank and overall geometry match common toolholder and chuck standards, simplifying tool selection and replacement. The HSS designation (High Speed Steel) indicates good toughness and edge retention for standard metal drilling tasks. This combination enables workshops to maintain inventory consistency while choosing a tool that balances cost and performance. Application range and user guidance Engineers, metal fabricators and service technicians will find this Type N drill particularly useful for general-purpose drilling in alloyed and unalloyed steels, cast iron and non-ferrous metals. For best results, select proper cutting speeds and use cutting fluid when drilling steels above moderate hardness; this reduces heat, preserves the cutting edge and improves cycle time. Note that for very soft materials or abrasive masonry, material-specific drills are preferable. Strong recommendation: For precision metal drilling choose the MetavCUT Twist Drill Type N with short HSS design — METAV Werkzeuge offers expert advice and technical support via info@metav-werkzeuge.com, phone +49 2822 7131930 and WhatsApp +49 170 2837271 Designation: Twist Drill Brand: MetavCUT SKU: 400625-FDA Diameter: 6.25 mm Material: HSS (High Speed Steel) Type: Type N Execution: short Colour: black Tip angle: 118° Spiral length: 57 mm Overall length: 101 mm Standard: DIN 338 Application: Drills for metal For drill machine: Drilling Machine Manufacturer: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What is the Twist Drill from MetavCUT used for? The MetavCUT Twist Drill Type N is primarily applied to metalworking tasks; it is intended for drilling into high-strength materials and larger diameters where robust performance is required. Its form allows relatively easy resharpening and it tolerates higher loads during cutting. Which three drill types exist? Commonly distinguished drill types are metal drills, wood drills and stone/concrete drills; the MetavCUT Twist Drill belongs to the metal drill category and is optimised for steel and similar materials. Why are twist drills pointed? Pointing the tip of a twist drill reduces the cross-cutting edge at the tip, which significantly lowers friction and required feed forces; this sharpening also improves centre holding so the drill seats more accurately in the workpiece. Can a Twist Drill be used to drill wood? A metal-oriented Twist Drill such as the MetavCUT Type N can be used in wood, but guidance is reduced and the finish is typically less clean than with a dedicated wood bit; advantages include easier resharpening and less aggressive self-feeding. At what drilling depths are twist drills most commonly used? Twist drills are the standard choice for through-hole drilling; they are most frequently used for diameters up to 20 mm and drilling depths up to about 100 mm, making them suitable for typical workshop operations. What is better, HSS or HSSE? The assumption that HSSE is always superior to HSS is not universally correct; decision-making should consider working conditions and whether the slightly higher investment in HSSE is justified by the specific application.
6.25mm HSS-G Twist Drill DIN 338 ,short, bright finished, Type N - MetavCUT
Die kompakte Kombination aus HSS‑G Material, geschliffenem Schaft und 135° Spitzenwinkel liefert schnelle, präzise Bohrungen in Stahl bei hoher Rundlaufgenauigkeit. Bestellen Sie den Spiralbohrer 6,25 mm von MetavCUT direkt über Metav oder fragen Sie unsere Beratung bei Bedarf an. Spiralbohrer 6,25 mm HSS‑G Kurz (Typ N) — MetavCUT, SKU 450625-FDA Der Spiralbohrer ist ein kurzer, geschliffener HSS‑G Metallbohrer für präzise Bohrungen in legierten und unlegierten Stahl sowie Gusswerkstoffe. Spiralbohrer 6,25 mm HSS‑G, kurz Geschliffener Schaft für hohe Rundlaufgenauigkeit 135° Spitzenwinkel für harte Werkstoffe Spiralänge 63 mm für stabile Spanabfuhr Geeignet für Handbohrmaschine und Stationär Präzision und Effizienz bei harten Werkstoffen Der kurze, geschliffene HSS‑G Kurzbohrer reduziert die Auskraglänge und damit das Verbiegen und Vibrieren während des Bohrens. Dadurch entsteht eine deutlich höhere Stabilität, was besonders bei legierten Stählen und Temperguss wichtig ist. Die geschliffene Geometrie sorgt für sehr scharfe Schneiden und saubere Bohrlöcher, während der 135° Spitzenwinkel das Anbohren in harten Werkstoffen erleichtert und die Anbohrzeit reduziert. Geeignet für Werkstatt und mobile Anwendung Im Standard‑Bereich von 2,0 mm bis 13,0 mm bietet dieser Kurzbohrer ein ausgewogenes Verhältnis aus Handhabung und Leistung. Die Ausführung als Typ N mit normaler Spirale macht ihn prädestiniert für den Einsatz in der Handbohrmaschine ebenso wie in stationären Bohrmaschinen. Bei der Nutzung in mobilen Geräten empfiehlt sich eine stabile Spannaufnahme und moderate Drehzahlen, um die Bruchsicherheit zu erhöhen. Normkonforme Fertigung und Materialeigenschaften Die Herstellung richtet sich nach DIN 338, die kurze Spiralbohrer mit Zylinderschaft normiert. Die Kombination aus HSS‑G und geschliffenem Schaft bedeutet: hohe Schneidleistung und exakte Rundlaufwerte. Geschliffene Bohrer bieten feinste Schneidkanten und enge Toleranzen; sie sind jedoch empfindlicher gegenüber Schockbelastungen, weshalb Kühlung und gleichmäßiger Vorschub empfohlen werden. Anwendungshinweise und arbeitssicherheit Für optimale Ergebnisse wird die Verwendung von Schneidöl oder Kühlmittel empfohlen, besonders beim Bohren in gehärtetem Stahl. Vorbohren ist bei sehr dicken oder zähen Werkstoffen empfehlenswert, um die Querschneide zu entlasten. Die kurze Spiralänge von 63 mm unterstützt die Spanabfuhr bei üblichen Bohrtiefen; bei tiefen Sacklochbohrungen sind abgestufte Aufbohrschritte zu erwägen, um Überhitzung und Spanverwicklung zu vermeiden. MetavCUT empfiehlt diesen HSS‑G Kurzbohrer für präzise Metallbohrungen; bei Fragen zur Einsatzoptimierung erreichen Sie uns per eMail info@metav-werkzeuge.com oder Telefon +49 2822 7131930. Produktmerkmale Artikelnummer: 450625-FDA Marke: MetavCUT Serie: Standard Line Bezeichnung: Spiralbohrer Typ: Typ N Fakten Durchmesser: 6,25 mm Gesamtlänge: 101 mm Spirallänge: 63 mm Spitzenwinkel: 135° Verpackungseinheit: 10 Besonderheiten Material: HSS-G (Schnellarbeitsstahl, geschliffen) Schaft Ausführung: geschliffen (vollständig geschliffener Zylinderschaft) Norm: DIN 338 (kurze Spiralbohrer mit Zylinderschaft) Farbe: blank Für Bohrmaschine: Handbohrmaschine FAQ Für welche Materialien eignet sich der Bohrer am besten? Der Kurzbohrer von MetavCUT (Spiralbohrer 6,25 mm, Typ N, SKU 450625-FDA) eignet sich besonders für legierte und unlegierte Stähle, Gusseisen sowie Nichteisenmetalle und Hartkunststoffe aufgrund des HSS‑G Werkstoffs und des 135° Spitzenwinkels. Kann der Bohrer in einer Handbohrmaschine verwendet werden? Ja, die Ausführung ist für die Nutzung in der Handbohrmaschine geeignet; dennoch ist auf eine feste Spannaufnahme und moderate Drehzahl zu achten, damit der geschliffene Bohrer nicht durch seitliche Kräfte beschädigt wird. Warum ist geschliffener HSS besser für Metallbohrungen? Geschliffene HSS‑Bohrer bieten sehr scharfe Schneidkanten und hohe Rundlaufgenauigkeit, was saubere Bohrlöcher erzeugt. Beim Spiralbohrer MetavCUT bedeutet das bessere Oberflächenqualität, allerdings erhöhte Empfindlichkeit gegen Stoßbelastungen. Ist Kühlung beim Bohren mit diesem Bohrer erforderlich? Bei harten oder dicken Werkstoffen wird Kühlung oder Schneidöl empfohlen, um Überhitzung zu vermeiden und die Standzeit des HSS‑G Bohrers zu verlängern. Dies gilt insbesondere bei stationärem Einsatz und höheren Vorschubkräften. Benötigt man Vorbohren für größere Bohrtiefen? Bei tiefen Bohrungen oder zähen Werkstoffen empfiehlt sich Vorbohren oder mehrstufiges Aufbohren zur Entlastung der Querschneide; der Kurzbohrer ist für typische Anwendungen im Standard‑Bereich konzipiert.
6.2mm HSS Twist Drill DIN 338 ,short, roll forged, black, Type N - MetavCUT
Twist Drill — Type N short HSS, Ø 6.2 mm, 118°, black, DIN 338, MetavCUT The Twist Drill Type N short HSS is a precision metalworking drill with a 6.2 mm diameter, a 118° tip angle and a compact design for stable, accurate holes in metal. Short HSS design for improved stability DIN 338 compliant short twist drill 6.2 mm diameter for precise metal holes 118° tip for controlled entry Suitable for drilling machines and hand drills Stable drilling for accurate metal holes The short HSS construction reduces overhang and vibration, delivering higher stability and more precise results when machining metal. Because the flute length is reduced, the tool resists bending and provides consistent concentricity in through-holes. This results in cleaner bores and less rework when working on components that demand tight tolerances. Material and geometry explained for reliable results Made from High Speed Steel (HSS), the drill combines toughness with wear resistance ideal for common metalworking tasks. The 118° tip angle eases centring on curved or softer surfaces and lowers the initial cutting forces; this geometry is particularly effective for general metal grades and reduces the chance of walking at the start of the hole. Short drills per DIN 338 are optimised for rigid setups and stationary or portable drilling machines. Where this drill excels and who benefits Designed primarily as a Drills for Metal tool, the Type N short configuration suits workshops, toolrooms and maintenance pros seeking repeatable performance in steel, cast iron, non-ferrous metals and plastics. The compact format is beneficial for confined setups or when using hand-held drilling devices, delivering greater control and faster, more reliable hole-making for production and repair tasks. Choose the MetavCUT Twist Drill Type N short HSS for dependable metal drilling — for personalised technical advice and application support contact METAV Werkzeuge: info@metav-werkzeuge.com · Phone: +49 2822 7131930 · WhatsApp: +49 170 2837271 Designation: Twist Drill Brand: MetavCUT SKU: 40062-FDA Diameter: 6.2 mm Spiral length: 57 mm Overall length: 101 mm Tip angle: 118° Type: Type N Execution: short Material: HSS Colour: black Suitable for: Drilling Machine (Hand Drill) Application: Drills for Metal Standard: DIN 338 Manufacturer: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What is the Twist Drill Type N by MetavCUT used for? The MetavCUT Twist Drill Type N is primarily used for machining metal; it is particularly suitable for drilling in alloyed and unalloyed steel, cast iron, non-ferrous metals and certain plastics. Its short HSS design makes it robust for demanding tasks and larger drill diameters where stability and precision are required. Which three drill types are commonly available? Common drill categories are metal drills, wood drills and stone/masonry drills. The MetavCUT Twist Drill Type N falls into the metal drills group and is tailored to metalworking applications.
6.2mm HSS-E Twist Drill DIN 338 ,short, 5% cobalt-alloyed, Type N - MetavCUT
Twist Drill (Type N) — 6.2 mm, 135° tip, short HSS‑E, 5% cobalt‑alloyed, DIN 338 — MetavCUT A Twist Drill (Type N) designed for precise metal drilling, combining a 6.2 mm diameter and a 135° tip angle in a short, stable execution suitable for demanding machining tasks. Type N Twist Drill, 6.2 mm diameter 135° tip angle for hard materials Short execution for higher stability HSS‑E with 5% cobalt for improved toughness Fully ground shank, DIN 338 compliant Exceptional stability and precision for metalworking Short-form drills deliver measurable advantages when precision matters. The short design of this MetavCUT Twist Drill reduces the unsupported overhang, which increases stability and lowers the tendency to wander or bend under load. Combined with the 135° tip angle, the geometry shortens pilot time and improves centring in harder materials. For production environments that require repeatable hole quality, the shorter spiral length also reduces vibration and contributes to more consistent hole diameter and surface finish. Material composition for longer life under stress Constructed from HSS‑E and alloyed with 5% cobalt, this short Twist Drill offers higher hot hardness and greater wear resistance than standard HSS. The cobalt content increases toughness at elevated temperatures, making the tool more suitable for drilling alloyed and unalloyed steel, cast iron, non‑ferrous metals and certain plastics. The fully ground flute geometry provides very sharp cutting edges and high running accuracy; however, grinding can increase brittleness, so coolant use and stable clamping are recommended to maximise tool life. Designed for drilling machines and demanding applications Classified to DIN 338, this Type N drill is the classical metal drill geometry optimised for machining of metallic workpieces on drilling machines. The shorter overall length and fully ground spiral make it particularly suited to stationary machines and operations that require high precision rather than freehand drilling. Typical applications include workshop fabrication, maintenance, toolmaking and any task where controlled drilling into Steel and similar materials is required. Note that Type N is not optimised for very soft materials where specialised geometries perform better. Practical advice for safe and efficient use When using the MetavCUT Twist Drill, ensure secure clamping and appropriate coolant or cutting fluid to dissipate heat and extend tool life. Start with a light feed to establish the hole, especially in harder materials, and avoid excessive spindle speeds that can overheat the tip. The 135° point reduces entry forces and improves centring for harder alloys, while the short execution minimises deflection—both contributing to cleaner, more accurate holes. For portable handheld drilling machines, consider the shorter projection to reduce user fatigue and increase control. The MetavCUT short Twist Drill (Type N) is recommended for professionals seeking stable, precise metal drilling; for expert technical advice or to confirm suitability for specific tasks contact METAV Werkzeuge — Email: info@metav-werkzeuge.com • Phone: +49 2822 7131930 • WhatsApp: +49 170 2837271 Twist Drill Brand: MetavCUT SKU: 47062-FDA Diameter: 6.2 mm Overall length: 101 mm Spiral length: 63 mm Tip angle: 135° Type: Type N Execution: short Material: HSS‑E Colour: 5% cobalt‑alloyed Shank design: fully ground Series: Standard Line Standard: DIN 338 For drilling machine: Drilling Machine Application: Drills for metal Manufacturer: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What is the MetavCUT Twist Drill (Type N) mainly used for? The MetavCUT Twist Drill (Type N) is primarily applied for machining high‑strength materials and larger bore diameters. Its short form suits precise work and makes the drill easier to re‑grind while maintaining resistance to higher loads in metalworking operations. Which three drill types exist? There are three common drill types: metal drills, wood drills and stone/concrete drills. The MetavCUT Twist Drill (Type N) belongs to the metal drill category, optimised for use in metalworking environments. Why are Twist Drills pointed? The point geometry reduces the cross‑cut at the tip of a Twist Drill, which lowers friction and thus requires smaller feed forces. By sharpening the tip, the drill centres more reliably in the workpiece and cuts with less resistance, improving entry behaviour and hole quality. Can you use a Twist Drill to drill wood? A metal drill such as the MetavCUT Twist Drill (Type N) can be used in wood, but guidance and centring are generally poorer and the finish may be less clean compared with purpose‑made wood bits. Metal drills are easier to re‑grind and show less self‑feed, which can be an advantage in some hobby or repair scenarios. For which drilling depths is the Twist Drill most commonly used? A through hole in a solid piece is typically executed with a Twist Drill. For diameters up to 20 mm and drilling depths up to 100 mm, the Twist Drill is the most frequently used tool. The MetavCUT Twist Drill (Type N) is therefore appropriate for many standard metal drilling tasks. What is better, HSS or HSSE? The common assumption that HSSE steels are always superior to standard HSS is not universally correct. Choose between HSS and HSSE based on actual working conditions and whether the higher purchase cost of HSSE is justified by the specific performance benefits required.
6.2mm HSS-G Body Drill ,double sided, bright finished - MetavCUT
Der geschliffene Karosseriebohrer kombiniert Präzision und Alltagstauglichkeit: Die HSS‑G‑Geometrie ermöglicht bis zu 40 % schnelleres Bohren bei deutlich geringerer Anpresskraft, die doppelseitige Ausführung verlängert die Nutzungsdauer durch Umkehrbarkeit, und der 135° Spitzenwinkel sorgt für saubere Ansätze in härteren Werkstoffen. Nutzen Sie diese Kombination aus Effizienz, Stabilität und hoher Rundlaufgenauigkeit und beziehen Sie den Bohrer direkt über Metav oder klären Sie Details telefonisch oder per E‑Mail. Karosseriebohrer »58062-FDA« von MetavCUT (HSS‑G, 6,2 mm) Der Karosseriebohrer ist ein doppelseitig ausgeführter HSS‑G‑Bohrer, konzipiert für präzise Metallbohrungen in Werkstatt und Karosseriebau Karosseriebohrer »58062-FDA« von MetavCUT Geschliffenes HSS‑G für präzise Metallbohrungen Doppelendbohrer: beidseitig einsetzbar 6,2 mm Durchmesser, Spirallänge 16 mm 135° Spitzenwinkel für härtere Werkstoffe Effiziente Leichtarbeit dank geschliffener HSS‑Geometrie Die geschliffene HSS‑G‑Geometrie reduziert die Anbohrkräfte deutlich und ermöglicht ein bis zu 40 % schnelleres Bohren gegenüber herkömmlichen HSS‑Bohrern. Für Anwender bedeutet das weniger Ermüdung bei wiederkehrenden Bohrvorgängen und eine höhere Produktivität in der Werkstatt. Außerdem führt der CNC‑Schliff zu sehr scharfen Schneiden und hoher Rundlaufgenauigkeit, was saubere Bohrlöcher in legierten und unlegierten Stählen, Gusswerkstoffen sowie Hartkunststoffen fördert. Doppelseitige Bauform für geringere Stillstandszeiten Die doppelseitige Ausführung macht den Bohrer besonders wirtschaftlich: Ist eine Spitze stumpf, kann der Bohrer einfach gewendet werden, so dass ein zweites Schneidenpaar sofort verfügbar ist. Die kompakte, stabile Bauform eignet sich speziell für Niet‑ und Dünnblecharbeiten in der Karosseriebranche und reduziert den Bedarf an Ersatzbohrern. Aufgrund der geschliffenen Fertigung sollte bei stationärer Nutzung eine angemessene Kühlung eingesetzt werden, um Bruchrisiken zu minimieren. Praxisgerechte Einsatzempfehlungen und Zielgruppe Mit 6,2 mm Durchmesser gehört der Bohrer zum Standard‑Bereich und ist ideal für Werkstätten, Karosseriebau und montageorientierte Anwender sowie für viele Heimwerkerprojekte. Für besonders präzise Anwendungen empfiehlt sich Vorzentrieren mit einem Zentrierbohrer, um Wandern beim Anbohren zu vermeiden. Die Kombination aus 135° Spitzenwinkel und geschliffener Schaftausführung sorgt für saubere Ansätze, besonders beim Bohren in härtere Materialien; bei zähen Werkstoffen Kühlung und moderater Vorschub verwenden. Empfehlung: Setzen Sie auf die MetavCUT Standard Line für langlebige, präzise Blecharbeiten und ordern Sie den Karosseriebohrer direkt über Metav per E‑Mail info@metav-werkzeuge.com oder Telefon +49 2822 7131930. Produktmerkmale Artikelnummer: 58062-FDA Marke: MetavCUT Bezeichnung: Karosseriebohrer Serie: Standard Line Verpackungseinheit: 10 Anwendung: Bohrer für Metall Ausführung: doppelseitig Fakten Durchmesser: 6,2 mm Gesamtlänge: 66 mm Spirallänge: 16 mm Spitzenwinkel: 135° Besonderheiten Material: HSS-G Schaftausführung: geschliffen Farbe: blank Für Bohrmaschine: Handbohrmaschine Verpackungseinheit: 10 Hinweis: G = geschliffen – scharfe Kanten, hohe Rundlaufgenauigkeit FAQ Für welche Materialien eignet sich der Bohrer am besten? Der MetavCUT Karosseriebohrer Standard Line (SKU 58062‑FDA) eignet sich besonders für legierten und unlegierten Stahl, Gussstahl, Gusseisen, Sintereisen, Temperguss, Nichteisenmetalle sowie Hartkunststoff und liefert in diesen Werkstoffen saubere Bohrbilder. Kann der Bohrer mit einem Akku‑Bohrer verwendet werden? Ja, der Karosseriebohrer ist für den Einsatz mit handgeführten Bohrmaschinen geeignet; bei 6,2 mm Durchmesser empfiehlt sich jedoch vorheriges Zentrieren für sehr präzise Passungen, um Wandern beim Anbohren zu vermeiden. Was bedeutet doppelseitig konkret in der Praxis? Doppelseitig heißt, dass der Bohrer an beiden Enden eine Schneide besitzt; dies erlaubt einfaches Wenden im Schadensfall und reduziert Stillstandszeiten, was besonders bei Niet‑ und Dünnblecharbeiten vorteilhaft ist. Wie lässt sich die Bruchgefahr bei geschliffenen HSS‑Bohrern minimieren? Um Bruchrisiken zu reduzieren, sollte der geschliffene HSS‑G‑Bohrer mit moderatem Vorschub, geeigneter Drehzahl und, bei zähen Werkstoffen, mit Kühlung betrieben werden; stationäre Befestigung oder stabile Führung erhöht die Lebensdauer deutlich.
6.2mm HSS-G Twist Drill DIN 338 ,short, bright finished, Type N - MetavCUT
Twist Drill (Type N) — Short HSS‑G Drill, 6.2 mm, 135° Point, Bright Finished, Fully Ground, DIN 338 — MetavCUT The Twist Drill (Type N) is a short HSS‑G drill designed for precise metalworking tasks on drilling machines and hand drills, optimised for hard materials and stable, accurate hole creation. Short design for higher stability 6.2 mm diameter for precise holes 135° point angle for hard materials Fully ground HSS‑G for sharp, accurate cuts Conforms to DIN 338 for industrial compatibility High performance for demanding metal drilling Built to deliver measurable productivity, this Twist Drill in HSS‑G quality combines a short overall length with a fully ground geometry to reduce vibration and improve centring. The 135° Point Angle eases penetration into harder metals such as stainless steel, while the CNC grinding of the flutes yields very sharp cutting edges and excellent runout accuracy. As a result, users experience up to 40% faster drilling and require 50% less feed force compared with conventional HSS variants, making this tool a rational choice where efficiency and repeatability matter. Short geometry that increases stability and precision A shorter projection from the chuck significantly reduces lever forces and deflection during drilling. The short design is therefore particularly suitable for operations where tight tolerances and straight, burr‑reduced holes are required. Because the flutes and cutting lips are produced by grinding rather than rolling, the drill achieves a cleaner hole surface and better dimensional consistency, especially when used with appropriate coolant and stationary or well‑supported setups. Material and cutting geometry explained for every user The HSS‑G (ground high speed steel) construction provides a balance of hardness and toughness for machining a wide range of metals. The designation Type N denotes the classic normal helix geometry tailored for metalworking; it is not optimised for soft timbers. Compliance with DIN 338 ensures standardised dimensions and shank form for easy mounting in chucks and toolholders. For less experienced users: a larger point angle reduces the tendency to wander on tough surfaces and shortens the time to break through the material. Where this drill delivers the most value This short Twist Drill is aimed at professional workshops and maintenance teams that work with alloyed and unalloyed steels, cast materials, non‑ferrous metals and hard plastics. It excels in jobs on bench drills and machine tools where stiffness is available and precise hole geometry is required. If the work involves deep, flexible setups or timber, consider dedicated long‑form or wood drills instead to match the application. MetavCUT recommends this Type N short HSS‑G Twist Drill for precision metalwork — for technical advice or to check suitability for a specific task, contact METAV Werkzeuge: info@metav-werkzeuge.com • Phone +49 2822 7131930 • WhatsApp +49 170 2837271 Technical Information Designation: Twist Drill (Short) Brand: MetavCUT SKU: 45062-FDA Diameter: 6.2 mm Point Angle: 135° Type: Type N Material: HSS‑G (ground high speed steel) Finish/Colour: Bright Finished Shank Execution: Fully Ground Overall Length: 101 mm Spiral Length: 63 mm Application: Drills for Metal / Drilling Machine / Hand Drill use Norm: DIN 338 Execution: Short Model Series: Standard Line Shaft Treatment: Geschliffen (ground) Manufacturer: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What is a Twist Drill used for and which materials suit the MetavCUT Type N short drill? The MetavCUT Twist Drill Type N is primarily used for drilling metal; it is well suited to alloyed and unalloyed steels, cast materials, non‑ferrous metals and hard plastics, offering reliable centring and clean hole walls when used on drilling machines or supported hand drills. Why choose a short Twist Drill like the MetavCUT Type N for precision work? A short Twist Drill reduces overhang and bending, improving stability and rotational accuracy; the ground geometry of the MetavCUT Type N gives sharp cutting edges that help achieve precise diameters and reduce burr formation. For what is a Twist Drill mainly used? A Twist Drill is primarily applied in the machining of high‑strength materials and for larger hole diameters; its ground form is easy to sharpen and withstands greater loads, making it suitable for difficult metalworking tasks. Which three drill types exist? There are three main drill categories: Metal drills, Wood drills, Stone/Concrete drills. Why are Twist Drills points de‑pointed (split)? Splitting the point reduces the cross‑edge at the tip, lowering friction and therefore the required feed force; it also improves centring of the tip in the workpiece. Can a metal Twist Drill be used to drill wood? A metal drill can be used in wood, but guidance is poorer and hole finish is less clean; metal drills are easier to resharpen and have a lower self‑feed tendency compared with dedicated wood drills. At which drilling depths is the Twist Drill most commonly used? Twist Drills are typically used for through‑hole drilling; for diameters up to 20 mm and depths up to 100 mm, the Twist Drill remains the most commonly employed tool. Is HSS or HSSE better? The general assumption that HSSE is categorically superior to HSS is not universally correct; when choosing, evaluate whether the working conditions justify the higher cost of HSSE for your specific application.
6.2mm HSS-G Twist Drill DIN 338 ,short, bright finished, Type N - MetavCUT
Twist Drill — short HSS‑G Metal Drill, 6.2 mm, 135°, Type N, Bright Finished A short Twist Drill (Type N) designed for precision metalworking and use in drilling machines, offering high stability and fast cutting performance Short design for greater stability and precision HSS‑G material for sharp, durable cutting edges 135° tip angle for harder materials and faster entry Fully ground shank for excellent runout accuracy Precision and Stability for Demanding Metalwork Shorter overall length and a reduced overhang provide significantly higher stability during cutting operations. The combination of a short geometry and a fully ground shank minimises vibration and deflection, so holes remain concentric and tolerances are easier to hold. This design is especially advantageous when machining hard materials or when using smaller diameters, because the stiffer setup reduces the risk of chatter and improves hole quality. Faster Cutting with Lower Feed Force Thanks to the HSS‑G grind and optimized geometry, this drill achieves up to 40% faster drilling rates while requiring around 50% less feed force than conventional HSS tools. The 135° tip angle shortens penetration time in tough alloys and stainless steels by reducing the initial cutting resistance. For users this means quicker cycle times and reduced operator effort, particularly on demanding jobs where efficiency and repeatability matter. Engineered for Metalworking and Machine Use Designed to meet DIN 338, this short twist drill is tailored for metal applications including alloyed and unalloyed steel, cast steels, cast iron, sintered iron, non‑ferrous metals and hard plastics. The Type N normal spiral makes it a versatile choice for conventional metal drilling. Because ground drills can be more brittle than roll‑formed types, it is recommended to use adequate cooling and, where possible, a machine setup rather than hand‑only operation to maximise tool life and prevent breakage. Practical Advice for Safe and Accurate Results When setting up, ensure the drill is clamped securely in a high‑precision chuck and that the workpiece is firmly supported to avoid movement. Start with a suitable pilot or centre drill where needed, and adapt cutting speeds to the material and drill diameter. Regular sharpening of the cutting lips maintains centring behaviour and hole finish; ground HSS tools deliver excellent runout accuracy but benefit from controlled feed and coolant during deep or interrupted cuts. Strong recommendation: choose the MetavCUT Profi Line short Twist Drill for precise, efficient metal drilling — for technical advice or to confirm suitability for your application contact METAV Werkzeuge; we provide expert consultation and comprehensive support. 📧 info@metav-werkzeuge.com ☎️ +49 2822 7131930 ✔️ WhatsApp: +49 170 2837271 Twist Drill Brand: MetavCUT SKU: 48062-FDA Diameter: 6.2 mm Overall length: 93 mm Spiral length: 57 mm Tip angle: 135° Type: Type N Length execution: Short Shank execution: Fully ground Material: HSS-G Standard: DIN 338 Colour: Bright finished For drilling machine: Drilling Machine Application: Drills for metal Model series: Profi Line Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What is a Twist Drill used for? A Twist Drill is primarily used for machining high‑strength materials and larger diameters; it is especially applied to metalworking where robust performance is required. The design is easy to regrind and withstands higher loads, making it a common choice for drilling steels and tougher alloys. Which three drill types are there? The basic categories are Metal drills, Wood drills, and Stone/Concrete drills. Each type features geometry and flutes adapted to its target material to ensure effective chip evacuation and hole quality. Can this Twist Drill be used in hand drills or only in machines? The MetavCUT Profi Line short Twist Drill is optimised for machine use to exploit its stability and precision, but it can be used in a quality handheld drilling machine for light tasks. For heavy or deep drilling in hard materials, a stationary drilling machine and coolant are recommended to avoid excessive stress on the tool. Why are twist drills point‑ground? Point grinding reduces the cross‑edge at the tip, significantly lowering friction so less feed force is required. A ground point also improves centring in the workpiece, leading to more accurate hole positions and smoother drilling starts.
6.3mm HSS Twist Drill DIN 338 ,short, roll forged, black, Type N - MetavCUT
Twist Drill — Type N, Ø 6.3 mm, 118° point angle, short HSS, black, DIN 338 — MetavCUT The Twist Drill Type N is a short HSS metal-drilling bit designed for use in hand and drilling machines, offering precise, stable performance for metalworking tasks. Short HSS design for increased stability Conforms to DIN 338 for short twist drills 118° point angle for reliable centring on common metals Suitable for alloyed and unalloyed steel and non-ferrous metals Black finish reduces glare and aids chip evacuation Precision and durability for metalworking professionals The short HSS construction of this Twist Drill provides enhanced stability and reduced deflection during machining, making it ideal for accurate holemaking. Manufactured to DIN 338 specifications, the reduced projection length minimises chatter and improves concentricity when drilling in steel and cast iron. This results in consistently round holes and longer tool life compared with longer, more flexible bits. Versatile tip geometry that aids centring and feed Equipped with a 118° point angle, this Type N bit balances entry behaviour and cutting forces for general-purpose metal drilling. The geometry supports easier centring on slightly curved or irregular surfaces and is effective across a range of common metals. For users seeking a classic “Normal Spiral” performance, this bit provides a dependable compromise between fast penetration and controlled cutting action. Practical advantages for workshop and maintenance tasks This short Twist Drill excels in workshop and maintenance environments where accessibility and rigidity matter. The compact overall length reduces the exposed shank, lowering the risk of bend or breakage under side loads. For repetitive repair or assembly work on machinery and metal components, the improved stiffness translates into fewer broken bits and a more predictable drilling process. Material suitability and manufacturing benefits explained Made from High Speed Steel (HSS), the bit is suitable for alloyed and unalloyed steel, cast iron, non-ferrous metals and many plastics. HSS offers a favourable combination of hardness and toughness; roll-formed HSS variants reduce the risk of breakage for small-diameter drills and maintain edge integrity during standard metalworking operations. The Type N normal spiral is the classic choice for metal drilling and can be resharpened when necessary to extend service life. Strong recommendation: Choose the MetavCUT Twist Drill Type N for reliable, precise metal drilling; for personalised advice or technical data METAV Werkzeuge provides expert support — eMail: info@metav-werkzeuge.com | Phone: +49 2822 7131930 | WhatsApp: +49 170 2837271 Technical data Designation: Twist Drill Brand: MetavCUT SKU: 40063-FDA Diameter: 6.3 mm Spiral Length: 63 mm Overall Length: 101 mm Point Angle: 118° For Drill: Drilling Machine / Hand Drill Type: Type N Material: HSS (High Speed Steel) Execution: short Colour: black Application: Drills for metal Standard: DIN 338 Manufacturer: MetavCUT Manufacturer: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What materials can the MetavCUT Twist Drill Type N be used on? The MetavCUT Twist Drill Type N, made of HSS, is intended primarily for metalworking and is suitable for alloyed and unalloyed Steel, Cast Iron, Non‑Ferrous Metals and various Plastics; this composition provides a balance between hardness and toughness for common workshop tasks. What is a Twist Drill used for? A Twist Drill, such as the MetavCUT Twist Drill Type N, is mainly applied to the machining of high‑strength materials and larger drill diameters; its form allows straightforward resharpening and it withstands higher loads during drilling. Which 3 drill types are there? The three main drill categories are Metal Drills, Wood Drills and Masonry/Concrete Drills.
6.3mm HSS-E Twist Drill DIN 338 ,short, 5% cobalt-alloyed, Type N - MetavCUT
Twist Drill (Type N) — 6.3 mm, 135° Tip, Short, 5% Cobalt‑Alloyed, HSS‑E, DIN 338 The Twist Drill Type N is a short HSS‑E drill designed for precise metal drilling with hand and drilling machines, offering high stability and wear resistance in demanding machining tasks. Short design for improved stability and precision 5% Cobalt‑alloyed HSS‑E for increased heat resistance 135° Tip angle for harder materials and stainless steel Fully ground shank for excellent runout accuracy Conforms to DIN 338 for standardised short twist drills Exceptional Stability and Accurate Hole Making for Metalworking Short Spiral Geometry delivers a measurable benefit in everyday machining: the reduced overhang increases Stability and cuts down on bit deflection, so holes come out truer to size. This Short Twist Drill with a 63 mm Spiral Length and 101 mm Overall Length is particularly suited to operations where rigidity matters, such as drilling in steel or when using a Hand Drilling Machine. The 135° Tip shortens initial entry time in harder materials and helps maintain centring under load. Enhanced Material Properties for Longer Life under Heat and Load Manufactured from HSS‑E with 5% Cobalt, this Twist Drill offers greater red hardness and wear resistance compared with conventional HSS. The cobalt‑alloyed composition means the tool tolerates higher cutting temperatures and preserves cutting edges longer when machining alloyed and unalloyed steel, cast iron and non‑ferrous metals. HSS‑E (High Speed Steel with Cobalt) describes a faster heat‑resistant steel grade that balances toughness with hardness, reducing the need for frequent tool changes. Precision Grinding and Standard Compliance for Reliable Results The fully ground flute geometry produces very sharp cutting edges and high concentricity, yielding clean, accurate bores in metal. As defined by DIN 338, this Short Twist Drill is produced to standardised dimensions and tolerances for short drills with cylindrical shanks. Ground tools typically give better hole quality than roll‑formed alternatives; they are easier to resharpen but require proper cooling and appropriate speeds to avoid premature breakage. Optimised for Metal Applications and Practical Use Recommendations Designed as a classic Type N normal‑spiral metal drill, this tool is recommended for a range of metalworking tasks on both stationary and portable drilling equipment. The shorter cutting length reduces the risk of bending and is therefore ideal for precision holes and tougher materials. For best results, use suitable cutting speeds, adequate lubrication or coolant when drilling stainless or hardened steels, and secure the workpiece to minimise vibration. The construction allows for easier regrinding when required, extending service life. Strong recommendation: Choose the MetavCUT HSS‑E short Twist Drill for precise, high‑duty metal drilling — for personalised technical advice and application support contact METAV Werkzeuge; eMail: info@metav-werkzeuge.com ☎️ +49 2822 7131930 ✔️ WhatsApp +49 170 2837271 Designation: Twist Drill Brand: MetavCUT SKU: 47063-FDA Type: Type N Diameter: 6.3 mm Overall length: 101 mm Spiral length: 63 mm Point angle: 135° Material: HSS‑E Cobalt content: 5% cobalt‑alloyed Execution: Short Shank finish: Fully ground Conforms to: DIN 338 Application: Drills for metal Suitable for: Drilling Machine (Hand Drilling Machine) Model series: Standard Line Manufacturer: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What is the best use for the MetavCUT Twist Drill Type N? The MetavCUT Twist Drill Type N is primarily used for machining high‑strength materials and larger drill diameters; its short design and HSS‑E composition make it easier to resharpen and capable of withstanding higher loads during metalworking. Which three drill types are commonly distinguished? In general practice the main categories are Metal drills, Wood drills and Stone/Concrete drills; the MetavCUT Twist Drill belongs to the metal drill category and is optimised for steel and similar materials. Why are Twist Drills sharpened at the point? The point sharpening reduces the cross‑cut at the tip of the Twist Drill, lowering friction and therefore the required feed forces; additionally, a properly sharpened tip improves centring in the workpiece. Can a metal Twist Drill be used to drill wood? A metal drill such as the MetavCUT Twist Drill can be used in wood, but guidance and finish are typically inferior compared with dedicated wood drills; metal drills are easier to resharpen and exhibit less self‑feeding in soft materials. For which drilling depths is the Twist Drill most commonly used? A through hole in solid material is often executed with a Twist Drill; for diameters up to about 20 mm and drilling depths up to approximately 100 mm the Twist Drill is the most frequently used tool.
6.3mm HSS-G Twist Drill DIN 338 ,short, bright finished, Type N - MetavCUT
Twist Drill — Type N short, Ø 6.3 mm, 135° point, Bright finished, Fully ground, DIN 338, HSS‑G by MetavCUT The Twist Drill Type N short is a precision metal‑drilling bit with a 6.3 mm diameter and a 135° point angle, designed for stable, high‑accuracy work in hand drills and drilling machines. Short Type N Twist Drill for high stability Ø 6.3 mm HSS‑G fully ground cutting geometry 135° point angle for hard metals like stainless steel Fully ground shank ensures high concentricity Conforms to DIN 338 for metal drilling Reliable stability and precision for demanding metal jobs The short design of this Twist Drill delivers increased Stability and reduced deflection during drilling, which is particularly valuable when working with hard or thick metals. Because the Out‑of‑chuck length is shorter than standard bits, vibration is minimised and the tool gives a more concentric hole. This construction makes the bit especially suitable for precise setups on a drill press or for accurate handheld operations where hole quality matters. The fully ground geometry ensures sharp cutting edges and consistent hole diameters. Faster penetration and lower feed forces in hard materials A 135° Point Angle reduces the tendency to wander and shortens the initial penetration phase on tough substrates. Combined with the HSS‑G (ground high‑speed steel) material, the bit requires noticeably less feed force, improving operator comfort and control. These features support efficient machining in alloyed and unalloyed steel, cast steel, grey iron, sintered iron and many non‑ferrous metals, enabling cleaner holes and longer tool engagement before loss of edge. Suited applications and who benefits most This Type N short Twist Drill is designed for professional metalworkers, toolroom staff and maintenance technicians who need reproducible, high‑quality holes in metals. It works well in both stationary drilling machines and robust hand drills for repair, assembly and fabrication tasks. The drill is optimised for metalworking scenarios rather than soft timber or masonry, offering a reliable choice where precision and repeatability are priorities. Material, manufacturing and care for longer tool life Being HSS‑G means the flute geometry and cutting edges are produced by CNC grinding rather than rolling, giving sharper edges and superior roundness, though with slightly higher brittleness. For best results use cutting fluid or coolant when machining steels, and avoid heavy interrupted cuts without support. The fully ground shank improves runout performance in chucks and collets and allows for easier regrinding when the geometry permits; regrinding should follow the original geometry to maintain the 135° point behavior and drilling quality. Strong recommendation: choose the MetavCUT Twist Drill Type N short for precision metal drilling and contact METAV Werkzeuge for tailored advice and technical support — eMail: info@metav-werkzeuge.com • Tel: +49 2822 7131930 • WhatsApp: +49 170 2837271 Technical data Designation: Twist Drill Brand: MetavCUT Model Series: Standard Line Diameter: 6.3 mm Spiral Length: 63 mm Overall Length: 101 mm Point Angle: 135° Type: Type N Execution: short Colour/Finish: bright finished Shank Execution: fully ground Material: HSS‑G Standard: DIN 338 Suitable for: Drilling Machine, Hand Drill Application: Drills for Metal Manufacturer: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What is a Twist Drill used for and which materials suit the MetavCUT Twist Drill Type N short? The MetavCUT Twist Drill Type N short is primarily used for machining metal; it excels in drilling alloyed and unalloyed steel, cast steel, gusseisen, sintered iron and many non‑ferrous metals. Its short construction and ground geometry make it particularly effective for high‑precision metal holes and demanding industrial tasks. Which three drill types exist? Commonly distinguished drill types are Metal drills, Wood drills, and Masonry/Stone drills; the MetavCUT Twist Drill belongs to the metal drill category and is optimised for machining a wide range of metallic materials.
6.3mm HSS-G Twist Drill DIN 338 ,short, bright finished, Type N - MetavCUT
Twist Drill — MetavCUT Profi Line, 6.3 mm, 135°, Type N, Bright Finished, Short HSS‑G, DIN 338 The Twist Drill is a short Type N drill for Drilling Machines, designed for precise metal drilling in demanding industrial and workshop applications. Short design for higher stability HSS‑G ground for sharp cutting edges 135° tip angle for hard materials Fully ground shank for precise concentricity Conforms to DIN 338 for standardised quality Precision and faster drilling for metal components The MetavCUT short Twist Drill with HSS‑G material combines resilient cutting performance with precise geometry. Its 6.3 mm diameter and 135° tip angle reduce entry forces when penetrating hard metals, shortening drilling time and improving hole quality. This design is particularly suitable when drilling stainless steel or alloyed steels, because the larger tip angle helps centre the tool and minimises wandering on the work surface, delivering cleaner, more accurate holes. Short length increases rigidity and accuracy A shorter overall length means less overhang and therefore significantly higher Stability during machining. The reduced cantilever of this short execution lowers bending and chatter, which allows higher feed rates and better surface finish when compared with longer drills. For bench and machine work where runout and concentricity matter, the short Profi Line variant gives reproducible results and reduces the risk of breakage under heavier cutting loads. Ground geometry and material advantages explained The designation HSS‑G indicates a ground High Speed Steel, produced with CNC grinding to form the flutes and cutting edges. This results in very sharp edges and excellent roundness, which translate into precise holes and easier regrinding when required. The fully ground shank ensures accurate clamping and minimises axial runout in standard Drilling Machines. Customers benefit from improved tool life in many metalworking tasks, provided suitable cooling and moderate cutting parameters are used. Built for demanding metalworking tasks This Type N normal‑spiral drill is optimised for a wide range of metallic materials. It is particularly recommended for alloyed and unalloyed steels, cast and ductile irons, sintered metals and non‑ferrous metals, as well as hard plastics. The combination of short design, fully ground shank, and 135° tip supports reliable centring and consistent hole quality, making it a solid choice for toolrooms, maintenance shops and production environments focused on repeatable accuracy. Who should choose this Profi Line short Twist Drill Engineers, machinists and workshop professionals seeking reliable, precise metal drilling will appreciate the balance of speed and robustness offered by this tool. The short Twist Drill suits stationary and light moving machine applications where stability is crucial. For users prioritising easy reconditioning and sharp cut performance, the HSS‑G ground version offers straightforward resharpening and consistent results across repeated operations. Strong recommendation: Choose the MetavCUT Profi Line short Twist Drill for precision metal drilling — for expert, non‑binding advice contact METAV Werkzeuge by eMail: info@metav-werkzeuge.com, Phone: +49 2822 7131930, or WhatsApp: +49 170 2837271 Twist Drill Marke: MetavCUT SKU: 48063-FDA Diameter: 6.3 mm Tip angle: 135° Type: Type N Material: HSS‑G Execution: Short Spiral length: 63 mm Overall length: 101 mm Shank execution: Fully ground Finish/Colour: Bright finished Model series: Profi Line Application: Drills for metal For drilling machine: Drilling Machine Norm: DIN 338 Packaging unit: 10 Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What is the Twist Drill used for? The MetavCUT Twist Drill (Type N) is primarily applied to the machining of high‑strength materials and larger bore diameters. Its short, ground geometry is easier to sharpen and remains durable under greater loads, which makes it suitable for industrial metal drilling where tool resilience and repeatable hole quality are required. Which three drill types exist? When comparing drill categories, there are Metal drills, Wood drills and Stone/Concrete drills. The MetavCUT Twist Drill belongs to the Metal drills group and is engineered specifically for metalworking tasks rather than woodworking or masonry.
6.4mm HSS Twist Drill DIN 338 ,short, roll forged, black, Type N - MetavCUT
Twist Drill — Type N short HSS drill, 6.4 mm, 118°, black, DIN 338, MetavCUT The Twist Drill Type N short by MetavCUT is a compact metalworking drill for precise holes in steel and non-ferrous materials, designed for use with a hand drill and compliant with DIN 338. 6.4 mm diameter for accurate metal holes Short design per DIN 338 for high stability HSS material for elasticity and wear resistance 118° point angle for reliable centering Stability and precision for demanding metalworking A short spiral drill made to DIN 338 reduces overhang and vibration, so even thin-walled components can be drilled with greater dimensional accuracy. The reduced exposed length improves rigidity and lowers the risk of deflection, which means cleaner holes and less rework for metalworking professionals. This compact design is particularly advantageous when working from fixed jigs or on small workpieces where stability is essential. High-Speed Steel construction for standard machining tasks Manufactured from HSS (High Speed Steel), this Type N short drill combines toughness with a degree of flexibility that reduces fracture risk during common metal drilling jobs. For standard operations in alloyed and unalloyed steel, cast iron, non-ferrous metals and plastics, the material choice supports longer tool life under frequent use. The construction method improves resistance to chipping when drilling diameters under 6 mm and contributes to consistent drilling performance. Tip geometry and application suitability explained The 118° point angle favours reliable centering and controlled penetration in softer to medium-hard metals, making it well suited for general workshop use. As a Type N twist drill, it is optimised for metalworking rather than soft timber; the point geometry and flute design balance chip evacuation with cutting stability. Correct feed and moderate speeds prolong service life and yield round, burr-minimised holes for subsequent finishing operations. Who benefits from this short Type N twist drill Workshops, maintenance technicians and precision hobbyists seeking a robust everyday metal drill will appreciate the combination of 6.4 mm diameter, short overall length and HSS material. The tool is intended for use in hand-held drilling machines and small bench machines where operator control and low runout are priorities. Its design supports repeatable results for production runs of small to medium series or for single, critical repair tasks. Choose the MetavCUT Twist Drill Type N short for dependable metal drilling performance — for technical advice or to confirm suitability for your application contact METAV Werkzeuge: info@metav-werkzeuge.com | +49 2822 7131930 | WhatsApp +49 170 2837271 Technical Data Designation: Twist Drill Brand: MetavCUT SKU: 40064-FDA Diameter: 6.4 mm Spiral length: 63 mm Overall length: 101 mm Point angle: 118° Type: Type N Execution: short For use with: Hand Drill Colour: black Material: HSS Application: Drills for metal Standard: DIN 338 Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What is the Twist Drill Type N short best used for? The MetavCUT Twist Drill Type N short is primarily used for drilling metal; it excels in producing precise holes in alloyed and unalloyed steels, cast iron and non-ferrous metals when used in hand-held or small stationary drilling machines. Can the Twist Drill Type N short be used in wood? The MetavCUT Twist Drill Type N short can be used in wood, but as a metal-optimised drill it provides less guidance and a rougher finish than dedicated wood drills; it is easier to resharpen yet offers reduced self-feeding compared with timber-specific bits. What are Twist Drills used for? Twist Drills are mainly applied to the machining of high-strength materials and larger drill diameters; their form makes them straightforward to resharpen and able to withstand higher loads. Which three drill types exist? The principal categories are Metal drill, Wood drill, and Stone/Concrete drill. Why are twist drills sharpened (pointed)? Pointing reduces the cross edge at the tip of the Twist Drill, lowering friction and required feed forces while improving the drill's centring in the workpiece. At what drilling depths are twist drills most commonly used? A solid through-hole is typically executed with a Twist Drill; for diameters up to 20 mm and drilling depths up to 100 mm, the Twist Drill is the most common tool. Is HSS or HSSE better? The general assumption that HSSE steels are always superior to HSS is not universally correct; selection should consider actual working conditions and whether the higher cost of HSSE is justified.
6.4mm HSS-E Twist Drill DIN 338 ,short, 5% cobalt-alloyed, Type N - MetavCUT
Twist Drill Type N — 6.4 mm, 135°, short, 5% cobalt-alloyed, HSS‑E, DIN 338 The Twist Drill Type N is a short HSS‑E metal drill designed for precise work in Hand Drilling Machines and stationary setups. Short design for increased rigidity and accuracy 135° point angle for hard materials like stainless steel HSS‑E with 5% cobalt for improved heat resistance Fully ground shank for high concentricity and clean holes Compliant with DIN 338 for short twist drills Greater Precision through a Short, Stable Design The short configuration of this Twist Drill minimises overhang and produces higher stability during drilling, which directly benefits precision and reduces the risk of wandering. The fully ground Shank delivers excellent concentricity, resulting in cleaner, rounder holes in Metal. For operators seeking reproducible results on benches or in jigs, the reduced tendency to deflect means less rework and better fit for threaded components. Suited to Hard Materials — Faster Penetration, Better Control With a 135° Point Angle and the Type N Normal Spiral geometry, this short HSS‑E tool is optimised for demanding tasks in Steel, Cast Iron and other hard materials. The geometry shortens initial touch‑in time and helps maintain the centre when starting a hole. Compliance with DIN 338 indicates manufacture to accepted dimensions and tolerances for short twist drills, supporting consistent performance across batches and easy integration in production workflows. Practical Guidance for Efficient Use Use the Twist Drill in a suitable Drilling Machine with adequate clamping and coolant to extend tool life. The 5% cobalt-alloyed composition increases heat resistance, allowing for higher cutting temperatures and improved wear stability; nevertheless, coolant or lubricant is advised for continuous or deep drilling. The shorter overall length favours operations where stiffness and tool control are critical, such as drilling into thicker plates or working with tight positional tolerances. Material and Handling Benefits from HSS‑E Chemistry The HSS‑E grade combined with 5% cobalt yields a balance of hardness and toughness that performs well under thermal load. The Standard Line production and the fully ground flute geometry create sharp cutting edges and excellent runout characteristics. Operators should note that ground drills offer superior hole quality but can be more brittle than rolled alternatives; therefore, controlled feed rates and proper cooling will help prevent chipping and extend service intervals. Strong recommendation: Choose the MetavCUT short Twist Drill for demanding metal applications and contact METAV Werkzeuge for expert advice and personalised support — eMail: info@metav-werkzeuge.com · Phone: +49 2822 7131930 · WhatsApp: +49 170 2837271 Designation: Twist Drill Brand: MetavCUT SKU: 47064-FDA Type: Type N Diameter: 6.4 mm Point Angle: 135° Execution: short Overall Length: 101 mm Spiral Length: 63 mm Material: HSS‑E Colour / Surface: 5% cobalt-alloyed Shank: fully ground Application: Drills for metal For Drilling Machine: Drilling Machine Model Series: Standard Line Norm: DIN 338 Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What is the MetavCUT Twist Drill Type N used for? The MetavCUT Twist Drill Type N is primarily used for drilling Metal and is suitable for demanding applications where a short, stiff tool is required. It is especially effective on harder materials thanks to the 135° point angle and HSS‑E chemistry, which together improve centring and heat resistance. For what is a Twist Drill used? A Twist Drill is mainly applied to the machining of high‑strength materials and larger bore diameters. Its form allows relatively simple resharpening and it withstands higher loads. This geometry is commonly used where durability and the ability to drill tough materials are required. Which 3 drill types are there? Common classifications are Metal drills, Wood drills, and Masonry/Concrete drills. Why are Twist Drills point‑ground? Point grinding reduces the cross‑cut at the tip of the Twist Drill, which lowers friction and consequently the required feed forces. In addition, a ground tip improves centring in the workpiece and leads to more accurate, controlled drilling.
6.4mm HSS-G Twist Drill DIN 338 ,short, bright finished, Type N - MetavCUT
Kompakte Bauweise und geschliffene HSS-G Qualität sorgen für präzise Bohrbilder und geringeren Kraftaufwand; nutzen Sie die Kombination aus Stabilität, schneller Schnittleistung und Normkonformer Ausführung für zuverlässige Metallbearbeitung. Bestellen Sie den Spiralbohrer direkt über Metav Werkzeuge oder fragen Sie unsere Beratung bei Bedarf an. Spiralbohrer kurz, HSS-G, 6,4 mm von MetavCUT Der Spiralbohrer kurz bietet präzises Bohren in Metall bei hoher Stabilität und reduziertem Anpressdruck für stationäre und handgeführte Anwendungen. Kurze Ausführung für höhere Stabilität Geschliffen: hohe Rundlaufgenauigkeit 135° Spitzenwinkel für härtere Werkstoffe Geeignet für Handbohrmaschine und Werkbankbetrieb DIN 338 konform für kurze Spiralbohrer Hohe Stabilität für präzise Metallbohrungen Die kurze Ausführung reduziert die Auskraglänge und minimiert somit Vibrationen und Biegung beim Bohren in Stahl und Guss. Durch die verringerte Hebelwirkung bleibt die Bohrung maßhaltiger, was besonders bei präzisen Passungen und wiederholten Bohrungen Zeit spart. Die Bauweise empfiehlt sich für Einsatzfälle, in denen Stabilität und sauberer Werkstückrand entscheidend sind. Effiziente Schnittleistung bei geringerem Kraftaufwand Der HSS-G geschliffen garantiert sehr scharfe Schneiden und eine schnelle Spanabfuhr; dies ermöglicht bis zu 40 % schnellere Schnittgeschwindigkeit und benötigt bis zu 50 % weniger Anpresskraft gegenüber herkömmlichen HSS-Bohrern. Der 135° Spitzenwinkel reduziert das Auslaufen beim Anbohren härterer Werkstoffe und verkürzt die Anbohrzeit, was die Produktivität in Werkstatt und Produktion erhöht. Vielseitiger Einsatzbereich für Metallbearbeitung Mit einem Durchmesser von 6,4 mm fällt der Bohrer in den Standard-Bereich und ist ideal für Werkstatt, Montage und DIY-Projekte. Er eignet sich zum Bohren in legierten und unlegierten Stahl, Gussstahl, Gusseisen, Sintereisen, Temperguss, Nichteisenmetallen und Hartkunststoffen. Die Kombination aus Typ N Normalspirale und kurzer Länge macht den Bohrer zu einer guten Wahl für schnelle, wiederholbare Bohrungen. Geschliffene Fertigung: Präzision trifft auf Handhabungshinweis Die geschliffene Schaft- und Nutgeometrie erzeugt sehr hohe Rundlaufgenauigkeit und saubere Bohrlöcher, ideal für hohe Ansprüche an Maßhaltigkeit. Geschliffene Bohrer können im Vergleich zur gewalzten Variante etwas spröder sein; deshalb empfiehlt sich bei intensiver Nutzung ausreichend Kühlung und, wenn möglich, stationärer Betrieb zur Reduktion von Bruchrisiken. Sichern Sie sich den Spiralbohrer von MetavCUT (SKU 45064-FDA) für präzise Metallbearbeitung bei Metav Werkzeuge — bei Fragen erreichen Sie uns per E‑Mail info@metav-werkzeuge.com, Telefon +49 2822 7131930 oder WhatsApp +49 170 2837271 Produktmerkmale Bezeichnung: Spiralbohrer Hersteller: MetavCUT Serie: Standard Line Norm: DIN 338 SKU: 45064-FDA Ausführung: kurz Farbe: blank Schaftausführung: geschliffen Material: HSS-G Typ: Typ N Für Bohrmaschine: Handbohrmaschine Fakten Durchmesser: 6,4 mm Gesamtlänge: 101 mm Spirallänge: 63 mm Spitzenwinkel: 135° Verpackungseinheit: 10 Stück Besonderheiten HSS-G (geschliffen) für scharfe Schneiden und hohe Präzision Schaft geschliffen (CNC-Schliff): hohe Rundlaufgenauigkeit Typ N (Normalspirale): klassisches Metall-Bohrverhalten DIN 338: Klassifizierung kurzer Spiralbohrer mit Zylinderschaft FAQ Für welche Materialien ist dieser Bohrer geeignet? Der Spiralbohrer von MetavCUT (SKU 45064-FDA) eignet sich besonders für legierten und unlegierten Stahl, Gussstahl, Gusseisen, Sintereisen, Temperguss, Nichteisenmetalle und Hartkunststoff. Ist der Bohrer für Handbohrmaschinen geeignet? Ja, der Spiralbohrer kurz aus der Standard Line von MetavCUT ist für den Einsatz in Handbohrmaschinen geeignet, wobei die kurze Bauform für bessere Stabilität bei Handführung sorgt. Was bedeutet HSS-G und welchen Vorteil bietet es? HSS-G steht für Schnellarbeitsstahl geschliffen; der geschliffene Bohrer liefert schärfere Schneiden und hohe Rundlaufgenauigkeit, was sauberere Bohrlöcher und bessere Maßhaltigkeit ermöglicht. Warum ist der 135° Spitzenwinkel vorteilhaft? Der 135° Spitzenwinkel reduziert das Wandern beim Anbohren und verbessert das Eindringen in härtere Werkstoffe, wodurch die Anbohrzeit verkürzt und die Oberflächenqualität verbessert wird. Welche Verpackungseinheit ist verfügbar? Der Spiralbohrer von MetavCUT (SKU 45064-FDA) wird in einer Verpackungseinheit von 10 Stück geliefert.
6.4mm HSS-G Twist Drill DIN 338 ,short, bright finished, Type N - MetavCUT
MetavCUT Twist Drill — Twist Drill, 6.4 mm, 135°, Type N, Bright Finished, Short, DIN 338, HSS-G A MetavCUT Twist Drill for precision metalworking, the short 6.4 mm Type N cutter delivers stable, fast drilling in hard materials Short design for increased stability and precision 6.4 mm Diameter for accurate metal drilling 135° Tip angle optimised for hard materials HSS-G Material with fully ground geometry Conforms to DIN 338 for standardised quality Engineered for faster, more stable metal drilling The MetavCUT Twist Drill in a short execution combines a compact overall length with a reduced overhang to deliver higher stability and less tendency to deflect. Manufactured from HSS‑G (high speed steel, ground), the bit features a precision ground flute geometry that produces clean holes and reduces cutting forces. The short geometry yields up to 40% faster drilling and requires significantly less feed pressure compared with conventional HSS versions, making it especially suitable for demanding tasks in workshops and production environments. DIN 338 classifies this type of short twist drill with a cylindrical shank, ensuring compatibility with standard chucks and consistent manufacturing tolerances. Optimised tip geometry for hard and alloyed materials A 135° tip angle reduces the initial bite and improves centring in tougher metals such as stainless steel and alloyed steels, shortening contact time and improving tool life. Type N (normal spiral) provides a balanced flute helix suitable for metalworking, while the fully ground shank guarantees excellent concentricity and low runout when mounted in a drilling machine or hand drill. For users less familiar with the terminology: HSS‑G denotes that the cutting geometry is produced by grinding rather than rolling, which results in very sharp cutting edges and high hole quality; however, the ground structure is generally more brittle and benefits from adequate cooling during prolonged operations. Practical benefits, target users and safe handling tips Workshop technicians, maintenance staff and professional machinists will appreciate the combination of short overhang and robust HSS‑G material for producing precise bores in cast iron, sintered parts, non‑ferrous metals and hard plastics. When using the drill in handheld applications, reduced flex leads to fewer broken drills and a more predictable drilling result. To avoid premature breakage, apply moderate pecking cycles on deep holes, use coolant for heat dissipation and clamp workpieces securely. If there is uncertainty whether this cutter matches specific requirements or when additional technical data is needed, Metav Werkzeuge provides extensive and competent advice and support. Strong recommendation: Choose the MetavCUT short HSS‑G Twist Drill (Type N) for demanding metal applications — for expert consultation contact METAV Werkzeuge by eMail at info@metav-werkzeuge.com, by phone at +49 2822 7131930 or via WhatsApp at +49 170 2837271 Technical specifications Designation: Twist Drill Brand: MetavCUT SKU: 48064-FDA Model series: Profi Line Diameter: 6.4 mm Spiral length: 63 mm Overall length: 101 mm Tip angle: 135° Type: Type N Execution: Short Shank execution: Fully ground Finish / Colour: Bright finished Material: HSS-G Application: Drills for metal Suitable for: Drilling Machine / Hand drill Standard: DIN 338 Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What is a Twist Drill used for? The MetavCUT Twist Drill (Type N) is primarily used for machining high‑strength materials and larger bore diameters; its short, ground geometry makes it well suited to precise metalworking. This form is relatively easy to re‑sharpen and withstands significant loads while delivering clean bores, which is why it is often the tool of choice for workshops working with alloyed and unalloyed steel, cast iron and similar materials. Which three drill types are commonly distinguished? In general practice the main drill categories are metal drills, wood drills and stone/concrete drills; the MetavCUT Twist Drill belongs to the metal drill group and is optimised for metalworking tasks.
6.5mm HSS Twist Drill DIN 338 ,short, roll forged, black, Type N - MetavCUT
Der kurze Spiralbohrer von MetavCUT überzeugt durch seine Kombination aus HSS-Material, kurzer Ausführung und der Einhaltung der DIN 338, was hohe Stabilität und zuverlässige Ergebnisse beim Metallbohren gewährleistet. Bestellen Sie den Bohrer direkt über Metav Werkzeuge oder fragen Sie unsere Beratung an, falls Sie spezielle Einsatzfälle besprechen möchten. Spiralbohrer 6,5 mm von MetavCUT (HSS, Typ N, kurz) Der Spiralbohrer von MetavCUT eignet sich für präzise Metallbohrungen auf Handbohrmaschinen und stationären Geräten und bietet Stabilität durch kurze Bauart. Kurze Ausführung für hohe Stabilität HSS-Material für Stahl und Gusseisen DIN 338 konform für kurze Spiralbohrer Spitzenwinkel 118° für einfache Anbohrung Zylinderschaft geeignet für Handbohrmaschine Stabilität und Präzision für alltägliche Metallarbeiten Die kurze Ausführung des Spiralbohrers reduziert die Auskraglänge und erhöht dadurch die Stabilität beim Bohren. Gerade bei einem Durchmesser von 6,5 mm sorgt die reduzierte Hebelwirkung für saubere, maßhaltige Bohrungen und weniger Vibrationen. Werkstätten und Montagebetriebe profitieren von der höheren Standzeit und der geringeren Bruchgefahr gegenüber längeren Ausführungen, insbesondere bei gängigen Bohranwendungen in Stahl, Aluminium und Guss. HSS und Normen geben Planungssicherheit Der Bohrer besteht aus HSS (High Speed Steel), was eine gute Elastizität und Verschleißfestigkeit kombiniert. Die Fertigung nach DIN 338 klassifiziert ihn als kurzen Spiralbohrer mit Zylinderschaft und garantiert eine standardisierte Abmessung und Handhabung. Der Spitzenwinkel von 118° erleichtert das Anbohren auf leicht gewölbten Flächen und ist eine bewährte Wahl für allgemeine Metallbearbeitung. Passende Einsatzbereiche und Maschinenkompatibilität Dieser Spiralbohrer ist ausgelegt für den Einsatz im Standard-Bereich (2,0 mm bis 13,0 mm) und eignet sich für Handbohrmaschinen sowie stationäre Bohrmaschinen. Typische Anwendungen sind das Bohren in Baustahl, Aluminium, Nichteisenmetallen und Kunststoffen. Die Zielgruppe umfasst Handwerk, industrielle Werkstätten und ambitionierte Heimwerker, die eine robuste Lösung für Routinebohrungen suchen. Anwendungstipps für lange Lebensdauer Für optimale Ergebnisse empfiehlt sich das Anpunkten mit einem Zentrierbohrer bei hoher Präzision und der Einsatz von Kühlmittel oder Schneidöl bei Stahl, um Wärmeentwicklung und Werkzeugverschleiß zu reduzieren. Moderate Drehzahlen und gleichmäßiger Vorschub verlängern die Lebensdauer. Vermeiden Sie sehr tiefe Bohrungen ohne Zwischenspülung, da die Späne zuverlässig abgeführt werden müssen. Für präzise Metallbearbeitung empfiehlt MetavCUT diesen HSS-Spiralbohrer als zuverlässige Alltagslösung — Für Bestellungen oder technische Fragen kontaktieren Sie Metav Werkzeuge per eMail info@metav-werkzeuge.com oder Telefon +49 2822 7131930 Produktmerkmale Artikelnummer: 40065-FDA Marke: MetavCUT Bezeichnung: Spiralbohrer Ausführung: kurz Norm: DIN 338 Daten Durchmesser: 6,5 mm Gesamtlänge: 101 mm Spirallänge: 63 mm Spitzenwinkel: 118° Verpackungseinheit: 10 Besonderheiten Material: HSS (High Speed Steel, Schnellarbeitsstahl) Typ: Typ N (Normalspirale) Farbe: schwarz Für: Handbohrmaschine Eignung: Bohrer für Metall FAQ Für welche Materialien ist der Spiralbohrer geeignet? Der Spiralbohrer von MetavCUT ist geeignet für legierten und unlegierten Stahl, Gusseisen, Nichteisenmetalle und Kunststoffe; bei harten Werkstoffen sind passende Schnittparameter und Kühlung zu beachten. Ist der Bohrer für Handbohrmaschinen geeignet? Ja, der Spiralbohrer mit Zylinderschaft ist kompatibel mit Handbohrmaschinen und eignet sich besonders für den Standard-Bereich von 2 mm bis 13 mm. Welchen Spitzenwinkel hat der Bohrer und was bedeutet das praktisch? Der Spiralbohrer hat einen Spitzenwinkel von 118°, was das Anbohren erleichtert und gutes Zentrierverhalten auf glatten oder leicht gewölbten Oberflächen ermöglicht. Nach welcher Norm ist der Bohrer gefertigt? Der Bohrer entspricht der Norm DIN 338, die kurze Spiralbohrer mit Zylinderschaft definiert und damit einheitliche Abmessungen sowie Einsatzbereiche sicherstellt. Welche Artikelnummer hat dieses Produkt für die Bestellung? Die Artikelnummer lautet 40065-FDA; bei Rückfragen zur Eignung oder Lieferumfang hilft MetavCUT beziehungsweise Metav Werkzeuge gern weiter.
6.5mm HSS-E Twist Drill DIN 338 ,short, 5% cobalt-alloyed, Type N - MetavCUT
Twist Drill — Type N, 6.5 mm, 135° tip, short, 5% cobalt-alloyed, HSS‑E, DIN 338 The Twist Drill Type N is a short HSS‑E metalworking drill designed for stable, precise holes in hard materials when used with a Drilling Machine. Short construction for increased stability 6.5 mm diameter for standard metalwork 135° tip for clean penetration in hard steels 5% cobalt‑alloyed HSS‑E for enhanced wear resistance Fully ground shank for high concentricity Durable alloy and compact design for demanding metalwork The HSS‑E composition with 5% cobalt gives this short twist drill exceptional heat resistance and wear stability when machining tough alloys. Because the design is short, the tool exhibits reduced overhang and less flexing, which directly improves hole accuracy and tool life under heavy cutting loads. This makes the drill particularly suitable for precision tasks such as locating holes in jigs and producing repeatable diameters in alloyed and unalloyed steel. Geometry and finish that improve hole quality and centring A fully ground flute geometry yields very sharp cutting edges and excellent concentricity; the typical result is cleaner chips and reduced burr formation. The 135° tip angle reduces thrust and improves entry in hard materials such as stainless steel, shortening the initial contact phase and helping to avoid wandering. As a Type N normal‑spiral twist drill, it balances chip evacuation and cutting stability for general metalworking. Recommended applications and suitable materials This short Twist Drill is engineered for use in metalworking: it performs well on alloyed and unalloyed steel, cast iron, non‑ferrous metals and many plastics. The compact length is an asset when working with hand or bench drilling machines where rigidity is crucial. Note that Type N geometry is not optimised for very soft woods; for woodworking, specialist drills provide better guidance and surface finish. Handling, cooling and reconditioning advice for longer life To maintain performance, use appropriate cutting speeds and a cutting fluid when machining steels; cooling reduces tool wear and the risk of tempering the cutting edge. Because the drill is manufactured ground, it can be resharpened by a skilled operator to restore the cutting lip and prolong service life. Observing correct feed and speed settings for the material ensures reliable hole quality and minimises breakage risk. We recommend MetavCUT’s Twist Drill Type N for precise metalworking — for personal technical advice or to confirm suitability for your application, contact METAV Werkzeuge: info@metav-werkzeuge.com | +49 2822 7131930 | WhatsApp +49 170 2837271 Designation: Twist Drill Marke: MetavCUT SKU: 47065-FDA Diameter: 6.5 mm Tip angle: 135° Spiral length: 63 mm Overall length: 101 mm Execution: short Type: Type N Material: HSS‑E Colour: 5% cobalt‑alloyed Shank finish: fully ground Model series: Standard Line Norm: DIN 338 For machine: Drilling Machine Application: Drills for metal Manufacturer: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What is the Twist Drill Type N best used for? The MetavCUT Twist Drill Type N is primarily used for metalworking; it excels when drilling alloyed and unalloyed steels, cast iron and other hard materials, offering good general performance on rotating drilling machines. Can the MetavCUT Twist Drill be used in a hand drilling machine? Yes, the short design of the MetavCUT Twist Drill makes it especially stable in hand and bench Drilling Machines, reducing the tendency to bend and improving hole accuracy when correct speeds and cooling are applied. What are Twist Drills used for? Twist Drills are mainly applied when machining high‑strength materials and larger diameters. Their form allows relatively simple resharpening and they withstand higher loads, making them suitable for robust metalworking tasks. Which three drill types exist? The three primary drill categories are metal drills, wood drills and stone/concrete drills.
6.5mm HSS-G Body Drill ,double sided, black finished without margin - MetavCUT
Karosseriebohrer (Body Drill) — HSS-G Twist Drill, 6.5 mm Diameter, 135° Tip, Double-sided, Black Finished Without Margin The Karosseriebohrer (Body Drill) is a double-sided HSS-G Twist Drill designed for precise metalworking with a 6.5 mm diameter and a 135° tip angle for demanding sheet and body applications. Double-sided twist drill for two usable cutting ends HSS-G material for precise metal drilling 6.5 mm Diameter with 135° Tip Angle Fully ground shank for high runout accuracy Black finished without margin for corrosion resistance Faster, more precise holes in hard metals The HSS-G construction and 135° tip angle are chosen to reduce drilling time and minimise feed force when working with tougher materials. Because the flute geometry is produced by CNC grinding rather than rolling, the Karosseriebohrer delivers high runout accuracy and clean hole edges, which is particularly valuable when preparing parts for riveting or welding. The sharper cutting edges also help extend tool life when used with appropriate cooling on stationary machines. Compact, double-ended design for workshop efficiency Designed as a double-sided / double-ended Twist Drill, this bit offers practical redundancy: if one tip becomes dull, simply reverse the bit and continue using the other end. The short, stable geometry suits thin-sheet and bodywork tasks and reduces vibration in hand and drilling machines. With a fully ground shank, clamping stability is improved, supporting consistent concentricity and safer operation in portable Drilling Machines. Where this drill performs best This Karosseriebohrer is optimised for metal drilling: alloyed and unalloyed steel, cast materials, non-ferrous metals and hard plastics. The 6.5 mm diameter and the chosen tip geometry make it particularly effective for holes used in body and panel work, rivet preparation and general maintenance tasks. Professionals in automotive repair, sheet metal workshops and maintenance departments will benefit from reliable entry behaviour and consistent hole quality. Handling, sharpening and application hints Because the flute geometry is ground, the twist drill requires careful handling: avoid aggressive impact and favour cooling when machining heat-sensitive or tougher cast materials to prevent premature chipping. If a tip becomes blunt, the double-ended design allows quick reversal; resharpening is possible but should respect the original 135° geometry to retain centring and cutting performance. Use steady feed and appropriate cutting fluid for best results with the HSS-G material. Strong recommendation from MetavCUT: choose this Karosseriebohrer for demanding metalwork where precision and durability matter — and contact METAV Werkzeuge for expert advice on application and tool selection; 📧 info@metav-werkzeuge.com ☎️ +49 2822 7131930 ✔️ WhatsApp: +49 170 2837271 Technical information Designation: Body Drill (Karosseriebohrer) Brand: MetavCUT SKU: 59065-FDA Material: HSS-G Diameter: 6.5 mm Tip Angle: 135° Type / Execution: double-sided Colour / Finish: black finished without margin Suitable for: Drilling Machine (Hand Drills / Portable Drilling Machines) Spiral Length: 20 mm Overall Length: 70 mm Shank Execution: fully ground Model Series: Profi Line Application: Drills for metal Packaging Unit: 10 Manufacturer: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What materials can the Karosseriebohrer (Body Drill) from MetavCUT drill effectively? The Karosseriebohrer by MetavCUT is suitable for alloyed and unalloyed Steel, Cast Steel, Gusseisen, sintered materials, non-ferrous metals and hard plastics, providing clean results when used with appropriate cutting fluid and machine speeds. Is the Karosseriebohrer suitable for use in a hand drill? Yes, the Karosseriebohrer (Body Drill) is designed for use with Drilling Machines including hand-held units, though optimal precision and cooling are achieved on stationary machines to reduce risk of breakage. For what is a Twist Drill used? A Twist Drill is primarily used for machining high-strength materials and larger bore diameters; its form is easy to sharpen and withstands significant loads, making it common in bodywork and sheet-metal applications. Which three drill types exist? The main categories are Metal drill bits, Wood drill bits, and Stone/Concrete drill bits. Why are Twist Drills sharpened? Sharpening reduces the cross cutting edge at the tip, which lowers friction and required feed force while improving centring of the tip in the workpiece. Can you use a metal drill to drill wood? A metal drill can be used in wood, but guidance and finish are inferior compared with purpose-made wood bits; metal drill bits are easier to resharpen and generally have less self-feed. At which drilling depths is the Twist Drill most commonly used? A solid bore is typically made with a Twist Drill; for diameters up to 20 mm and depths up to 100 mm the Twist Drill is the most frequently used tool. What is better, HSS or HSSE? The general assumption that HSSE is always superior to HSS is not correct; selection should consider working conditions and whether the higher acquisition cost of HSSE is justified.
6.5mm HSS-G Body Drill ,double sided, bright finished - MetavCUT
Karosseriebohrer — Body Drill, 6.5 mm, 135° tip, double sided, Bright Finished, HSS‑G, Fully Ground Shank The Karosseriebohrer is a double sided Body Drill designed for Drilling Machine applications, delivering precise metal drilling with a 135° tip and a Fully Ground HSS‑G geometry for tough materials. Double-ended design for twice the usable life HSS‑G ground geometry for precise metal drilling 135° tip for harder materials such as stainless steel Fully ground shank for improved runout accuracy Bright finish for corrosion resistance and visual inspection Exceptional Material Performance and Cutting Efficiency The Karosseriebohrer from MetavCUT combines a HSS‑G composition with CNC grinding to produce extremely sharp Cutting Edges and a consistent Spiral Geometry. This Ground Manufacturing method yields high Roundness Accuracy and clean, burr‑reduced holes in metals. The optimized geometry enables up to 40% faster drilling and requires up to 50% less thrust compared with conventional HSS variants, which directly reduces operator fatigue and cycle times in production environments. Built for Harder Materials and Reliable Hole Entry A 135° Tip Angle reduces walking and improves centring when working with tougher substrates like Stainless Steel, Cast Steel and other alloyed Steels. The double ended layout makes the Tool inherently more compact and stable, a design often favoured in bodywork and Sheet Metal operations where short, accurate holes are critical. Because the Bit can be reversed when one end dulls, downtime for tool changes is minimized while precision remains high. Precision Features That Support Workshop Standards The Fully Ground Shank and Bright Finished surface support consistent Tool Runout and easy visual inspection. Ground Flute Geometry creates clean chip evacuation and precise chip formation, resulting in smoother hole walls and less rework. Note that Ground HSS grades can be more brittle than rolled equivalents, so cooling and sensible feed rates are recommended for station‑type drilling and high‑duty cycles to extend Tool Life. Practical Application, Handling and Suitability This Body Drill is intended for Drilling Machine usage across a range of metals including unalloyed and alloyed Steel, Cast Iron variants and Non‑Ferrous Metals, as well as Hard Plastics. The double‑ended Twist Drill design is particularly suitable for workshop and industrial settings where short, precise holes are required and quick tool rotation between ends increases uptime. For hand tool operations, ensure compatible chucks and take appropriate safety measures. We recommend the MetavCUT Standard Line Karosseriebohrer for professionals requiring fast, accurate metal drilling; METAV Werkzeuge offers expert advice and technical support—contact via info@metav-werkzeuge.com or +49 2822 7131930 for tailored recommendations and application guidance Designation: Karosseriebohrer / Body Drill Brand: MetavCUT SKU: 58065-FDA Diameter: 6.5 mm Tip Angle: 135° Spiral Length: 20 mm Overall Length: 70 mm Execution: double sided Shank Execution: fully ground Material: HSS‑G For Drilling Machine: Drilling Machine Colour: Bright Finished Model Series: Standard Line Application: Drills for metal Manufacturer: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What is the best application for the Karosseriebohrer Body Drill by MetavCUT? The Karosseriebohrer Body Drill from MetavCUT is primarily used for precise metalwork, especially where short, accurate holes are required in Sheet Metal and Bodywork components; its double‑ended Twist Drill design and HSS‑G grinding make it suitable for alloyed and unalloyed Steel, Cast Iron, Non‑Ferrous Metals and Hard Plastics. Can the Karosseriebohrer Body Drill by MetavCUT be used in hand drills? Although the Karosseriebohrer Body Drill by MetavCUT is optimised for Drilling Machine applications, it can be used in appropriately rated Hand Drills if the chuck and operational parameters match the Tool requirements; for best results and safety, check recommended speeds and cooling. For what are Twist Drills used? A Twist Drill such as the Karosseriebohrer Body Drill by MetavCUT is mainly applied to the machining of high‑strength materials and larger hole diameters; the shape is easy to regrind and stands up to higher loads, making it a common choice for robust metalworking tasks. Which three drill types exist? Typical categories include Metal Drill, Wood Drill and Stone/Concrete Drill; the Karosseriebohrer by MetavCUT belongs to the Metal Drill family and is designed for demanding metal applications. Why are Twist Drills point‑sharpened? Point sharpening reduces the cross‑edge at the tip of a Twist Drill; for the Karosseriebohrer Body Drill by MetavCUT this lowers friction, reduces required feed force and improves centring, leading to cleaner holes and more controlled drilling. Can a Metal Drill be used for wood? A Metal Drill such as the Karosseriebohrer by MetavCUT can be used in Wood, but it typically offers poorer guidance and a less clean finish than a dedicated Wood Drill; regrindability and lower self‑feed may be advantageous for specific tasks. For which drilling depths is the Twist Drill most used? The Twist Drill design is commonly used for through‑holes and solid drilling; for diameters up to around 20 mm and depths up to approximately 100 mm a Twist Drill like the Karosseriebohrer Body Drill by MetavCUT is often the preferred tool. Is HSS or HSSE better for my application? The general belief that HSSE is always superior to HSS is not universally correct; evaluate whether the working conditions for the Karosseriebohrer Body Drill by MetavCUT require the additional cost of HSSE, considering cutting speed, material and coolant use before deciding.
6.5mm HSS-G Twist Drill DIN 1869 ,extra long, bright finished - MetavCUT
Twist Drill — Drill Bit, 6.5 mm, 135° point angle, extra-long, bright-finished, HSS-G, DIN 1869 A Twist Drill Drill Bit for deep metal drilling, optimised for Drilling Machines and hand-held drills. Extra-long geometry for deep drilling HSS-G material for high wear resistance 135° tip for harder materials Fully-ground shank for precise runout Conforms to DIN 1869 for demanding conditions Engineered for accurate, high-performance metal cutting This HSS-G Twist Drill combines a ground flute geometry with a high-speed-steel alloy to deliver clean, precise holes in tough materials. The CNC grinding process produces very sharp cutting edges and high concentricity, which reduces vibration and improves surface finish. As a result, drilling in alloyed and unalloyed steel, cast iron and non-ferrous metals becomes noticeably more consistent, while the reduced required feed force eases operator handling and minimises tool deflection. Deep holes and secured centring for demanding tasks Designed with an extra-long overall length and an extended spiral length, the geometry allows access to recessed or hard-to-reach positions without sacrificing stability. The 135° point angle is optimised for harder materials and shortens the initial plunge time while improving centring and chip evacuation. With a total length of 215 mm and a flute length of 150 mm, the bit is particularly suitable where standard lengths are insufficient and deep through-holes or extended reaches are required. Built for workshops, maintenance and production environments Manufactured for users who need reliable performance in metalworking, this Drill Bit suits machine shops, maintenance departments and on-site technicians working with steels up to 1000 N/mm². Compliance with DIN 1869 ensures reproducible quality and compatibility with industrial processes. The bright-finished surface supports easy visual inspection and handling on the shop floor while the fully-ground shank improves clamping accuracy in chucks and collets. Handling advice to maximise life and performance Because ground Twist Drills can be more prone to shock than rolled types, controlled machining parameters are recommended. Use appropriate cutting speeds, steady feed and coolant when drilling deep or hard materials to avoid thermal overload and chipping. If working with stainless or high-strength steels, the 135° tip and HSS-G composition reduce the tendency to work-harden; nevertheless, intermittent peck drilling or backing-off is advised for chip control during long bores. Regular inspection and resharpening extend service life while maintaining hole quality. Opt for the MetavCUT extra-long HSS-G Twist Drill for reliable deep-hole performance — for technical advice and application support contact METAV Werkzeuge by eMail at info@metav-werkzeuge.com, by phone at +49 2822 7131930 or via WhatsApp at +49 170 2837271 Designation: Twist Drill Brand: MetavCUT SKU: 32065-FDA Diameter: 6,5 mm Point angle: 135° Overall length: 215 mm Spiral length: 150 mm Execution: extra long Shank execution: fully ground Colour: bright finished For drilling machine: Drilling Machine / Hand Drill Material: HSS-G Model series: Standard Line Norm: DIN 1869 Application: Drills for metal Story trigger: bohrer UID: 32065-FDA Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What is this Twist Drill by MetavCUT best used for? The MetavCUT Twist Drill Drill Bit is primarily designed for drilling in metals; it excels in alloyed and unalloyed steel, cast iron and non-ferrous metals where deep, precise holes are required. Its HSS-G composition and ground geometry make it suitable for demanding workshop and production applications. Can the MetavCUT Twist Drill be used with a hand-held drill? Yes, the Twist Drill by MetavCUT is suitable for use in both Drilling Machines and hand-held drills, though for very deep or high-precision holes a machine-mounted setup with coolant and steady feed is recommended. For what are Twist Drills used? Twist Drills are mainly applied to the machining of high-strength materials and large-diameter drilling. Their geometry allows efficient chip removal and, when sharpened correctly, they withstand higher loads and cutting forces. Which three drill types exist? The three common drill types are metal drills, wood drills and stone/concrete drills. Why are Twist Drills point-ground (ausgespitzt)? Point-grinding reduces the cross-cutting edge at the tip, significantly lowering friction and required feed forces. It also improves the drill’s centring ability in the workpiece. Can a metal drill be used for wood? A metal drill can be used in wood, but guidance is poorer and the hole finish is typically less clean. Metal drills are easier to resharpen and have less self-feed than dedicated wood bits. For which drilling depths is the Twist Drill most used? A Twist Drill is commonly used for solid drilling. It is the most frequently used tool for diameters up to 20 mm and drilling depths up to 100 mm in many workshop settings.
6.5mm HSS-G Twist Drill DIN 1869 ,extra long, bright finished - MetavCUT
Spiralbohrer von MetavCUT – HSS‑G Extra Lang für Metall Der Spiralbohrer ist ein geschliffener HSS‑Bohrer in Extra‑Langausführung für tiefe Metallbohrungen und anspruchsvolle Werkstatt‑Anwendungen. MetavCUT Spiralbohrer HSS‑G geschliffen Extra lange Gesamtlänge 275 mm Spirallänge 190 mm für tiefe Löcher Spitzenwinkel 135° für harte Werkstoffe Geeignet für Handbohrmaschine und Stationär Schnelleres Bohren bei geringerer Anpresskraft sorgt für Effizienz Der geschliffene HSS‑G‑Schaft ermöglicht laut Hersteller ein bis zu 40 % schnelleres Bohren und reduziert die benötigte Anpresskraft um 50 % gegenüber herkömmlichen HSS‑Bohrern. Dieser Vorteil führt zu kürzeren Bearbeitungszeiten und geringerem Verschleiß an Maschine und Werkzeug. Für Anwender bedeutet das weniger Nacharbeit und eine höhere Stückzahl pro Schicht. Die lange Spirale transportiert Späne zuverlässig aus der Bohrung, was die Prozesssicherheit bei tiefen Löchern erhöht. Präzision und Materialvielfalt für anspruchsvolle Metallarbeiten Die Ausführung nach DIN 1869 und der Spitzenwinkel von 135° machen das Werkzeug besonders geeignet für legierten und unlegierten Stahl, Gussstahl, Gusseisen sowie Hartkunststoffe. Die geschliffene Geometrie sorgt für scharfe Schneiden und hohen Rundlauf, wodurch saubere Bohrlöcher mit geringen Maßabweichungen entstehen. Wer präzise Passungen in Stahl benötigt, profitiert von der Kombination aus Schnittqualität und Stabilität, muss aber auf geeignete Kühlschmierung und stationäre Aufnahme achten. Extra Länge und Spiralform für tiefe und schwer zugängliche Bohrungen Mit einer Gesamtlänge von 275 mm und einer Spirallänge von 190 mm ist der Bohrer speziell für tiefe Bohrungen und schwer zugängliche Arbeitspositionen konzipiert. Bei einem Durchmesser von 6,5 mm fällt das Werkzeug in den Standard‑Bereich und eignet sich für handgeführte Maschinen, sollte aber bei hohen Anforderungen an Rundlauf und Tiefe möglichst in einer Säulenbohrmaschine oder mit stabiler Aufnahme eingesetzt werden. Für besonders genaue Bohrbilder empfiehlt sich ein Zentrierpunkt vor dem Direktbohren. Materialeigenschaften, Anwendungshinweise und Pflege Die geschliffene Schaft‑Ausführung bietet hohe Schnittgüte, ist aber empfindlicher gegen seitliche Belastung; deshalb empfiehlt sich die Nutzung mit Kühlung und moderatem Vorschub. Begriffe wie „geschliffen“ bedeuten hier, dass die Spannuten per CNC‑Schliff ausgeführt sind statt gewalzt, was zu schärferen Kanten und höherer Rundlaufgenauigkeit führt. Die längebedingte Hebelwirkung erfordert eine sorgfältige Maschinenwahl, um Bruchrisiken zu minimieren. Sichern Sie sich den MetavCUT Spiralbohrer in HSS‑G für präzise, tiefe Metallbohrungen über Metav und nutzen Sie bei Bedarf unsere technische Beratung per E‑Mail oder Telefon, um die optimale Einsatzstrategie für Ihre Anwendung zu klären. Produktmerkmale Artikelnummer: 33065-FDA Marke: MetavCUT Serie: Standard Line Bezeichnung: Spiralbohrer Daten Durchmesser: 6,5 mm Gesamtlänge: 275 mm Spirallänge: 190 mm Spitzenwinkel: 135° Verpackungseinheit: 10 Besonderheiten Material: HSS-G Norm: DIN 1869 Schaftausführung: geschliffen Ausführung: extra lang Farbe: blank Für Bohrmaschine: Handbohrmaschine SKU: 33065-FDA FAQ Für welche Materialien eignet sich der MetavCUT Spiralbohrer am besten? Der MetavCUT Spiralbohrer HSS‑G eignet sich für legierten und unlegierten Stahl, Gussstahl, Gusseisen sowie Hartkunststoff und Nichteisenmetalle; durch den Spitzenwinkel 135° lassen sich härtere Werkstoffe besonders zuverlässig bearbeiten. Ist der Bohrer für Handgeführte Maschinen geeignet? Ja, der Spiralbohrer mit 6,5 mm Durchmesser ist grundsätzlich für Handbohrmaschine geeignet, empfiehlt sich bei tiefen Bohrungen jedoch mit stabiler Aufnahme oder stationärer Maschine einzusetzen, um Bruchrisiken zu reduzieren. Welche Vorteile bringt die geschliffene Schaftausführung? Die geschliffene Ausführung (HSS‑G) liefert schärfere Kanten, besseren Rundlauf und sauberere Bohrlöcher; das verbessert Maßhaltigkeit und Oberflächenqualität, erfordert aber angepasste Kühlung und vorsichtigen Umgang. Wie tief kann mit diesem Extra‑langen Bohrer gebohrt werden? Die Spirallänge von 190 mm erlaubt deutlich tiefere Bohrungen als Standardwerkzeuge; für sehr tiefe oder präzise Durchgangsbohrungen empfiehlt sich eine mehrstufige Vorgehensweise und geeignete Späneförderung.
6.5mm HSS-G Twist Drill DIN 1869 ,extra long, bright finished - MetavCUT
Twist Drill — 6.5 mm, 135° Point Angle, Extra Long, Bright Finished, HSS‑G, DIN 1869 The Twist Drill is an extra‑long HSS‑G drill designed for deep metal drilling with a 135° point angle and a bright finished, fully ground shank for high precision in demanding machining tasks. Extra‑long design for deep bore reach 6.5 mm Diameter with 235 mm Spiral Length 135° Point Angle for harder materials Fully ground (HSS‑G) for high runout accuracy Complies with DIN 1869 for demanding conditions Durable HSS‑G construction for precise metalwork The drill is made from HSS‑G, a high‑speed steel that is CNC‑ground to achieve sharp cutting edges and excellent roundness. This fully ground geometry reduces vibration and produces cleaner holes in alloys and hard materials. For users this means fewer reworks and better repeatability when machining components that require tight tolerances. Extra‑long geometry solves deep drilling challenges With an extra‑long overall length of 350 mm and a spiral (flute) length of 235 mm, this tool reaches deeper bore positions where standard drills cannot. The elongated design allows comfortable access in hard‑to‑reach setups and reduces the need for extensions. The 135° point angle shortens entry time in tougher steels and improves centring when starting a hole. Performance advantages and recommended machining practice Compared with standard HSS tools, the ground HSS design can deliver up to 40% faster drilling and requires less axial force, improving operator comfort and machine load. The Twist Drill by MetavCUT is intended primarily for drilling legiertem und unlegiertem Stahl, Gussstahl, Gusseisen, Nichteisenmetalle and hard plastics; use adequate coolant and reduced feed rates at greater depths to minimise breakage risk and extend tool life. Who benefits and how to get support Manufacturers, toolrooms and maintenance teams that demand long reach and high precision will find this Twist Drill particularly suitable. For stationary or machine‑based work, the bright finish and precise geometry ensure consistent hole quality. If uncertain whether this tool meets specific requirements or for complementary technical data, METAV Werkzeuge offers expert advice and application support. Contact METAV Werkzeuge for customised recommendations and assistance with feed, speed and coolant selection. I recommend the MetavCUT extra‑long HSS‑G Twist Drill for any deep metal drilling task that requires precision and enhanced tool life — for personalised advice contact METAV Werkzeuge at info@metav-werkzeuge.com or call +49 2822 7131930; WhatsApp +49 170 2837271 Designation: Twist Drill Brand: MetavCUT SKU: 34065-FDA Diameter: 6.5 mm Point angle: 135° Type / Execution: Extra long Finish / Colour: Bright finished Spiral length (Flute length): 235 mm Overall length: 350 mm Shank execution: Fully ground Material: HSS‑G Applicable machines: Drilling Machine (Hand drill suitable with precautions) Application: Drills for metal Model series: Standard Line Standard / Norm: DIN 1869 Manufacturer: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What is the Twist Drill used for and which materials suit it best? The Twist Drill from MetavCUT (Twist Drill) is mainly used for machining high‑strength materials and larger hole diameters; it is especially suitable for alloyed and unalloyed steel, cast steel, cast iron, non‑ferrous metals and hard plastics thanks to its HSS‑G composition and ground geometry. Can the MetavCUT Twist Drill be used for deep holes and what makes it suitable? Yes, the MetavCUT Twist Drill is designed for deep bores; its extra‑long overall length and a 235 mm spiral length, combined with the DIN 1869 Tieflochspirale, make it ideal for bore depths and difficult access situations. For what is a Twist Drill used? A Twist Drill is primarily applied when machining high‑strength materials and large hole diameters. Its shape allows easy resharpening and the ground geometry endures substantial loads, making it suitable for demanding metalworking. Which 3 drill types are there? Commonly distinguished drill types are: Metal drill (Metal drill), Wood drill (Wood drill), and Masonry/Concrete drill (Stone/Concrete drill). Why are Twist Drills pointed? Pointing reduces the cross‑edge at the drill tip; by pointing the Twist Drill the friction forces at the tip are substantially lowered, which requires less feed force and improves centring of the drill in the workpiece. Can a Twist Drill be used to drill wood? A metal Twist Drill can be used in wood but guidance and finish are inferior compared with dedicated wood drills. The MetavCUT Twist Drill can cut wood, yet results are less clean and the tool may have more tendency to pull itself in. For which depths is the Twist Drill most commonly used? A through hole in solid material is commonly executed with a Twist Drill. For diameters up to 20 mm and drilling depths up to 100 mm, the Twist Drill is the most frequently used tool. What is better, HSS or HSSE? The general belief that HSSE steels are universally superior to HSS is incorrect. Evaluate whether your working conditions justify the higher purchase cost of HSSE; for many applications HSS‑G (ground HSS) as used in the MetavCUT Twist Drill offers an optimal balance of performance and economy.
6.5mm HSS-G Twist Drill DIN 1897 ,extra short, bright finished, Type N - MetavCUT
Nutzen Sie die Kombination aus extra kurzer Bauform, HSS-G Material und dem 135° Spitzenwinkel für erhöhte Stabilität und schnelle Bohrfortschritte bei Metallarbeiten. Bestellen Sie den Spiralbohrer direkt über Metav Werkzeuge oder fragen Sie unsere Beratung an, wenn Sie unsicher sind, ob diese Ausführung zu Ihrer Anwendung passt. Spiralbohrer HSS-G extra kurz 6,5 mm von MetavCUT Der Spiralbohrer HSS-G in extra kurzer Ausführung ist für präzise Metallbohrungen mit Handbohrmaschine und Winkelbohrer konzipiert und bietet hohe Verdrehungsfestigkeit bei beengten Platzverhältnissen. Extra kurze Bauform für mehr Stabilität HSS-G für hohe Standzeit und Zähigkeit Spitzenwinkel 135° für harte Werkstoffe Zylinderschaft für universelles Einspannen Geeignet für Handbohrmaschine und Winkelbohrer Mehr Stabilität bei beengten Platzverhältnissen Die extra kurze Bauform reduziert Hebelkräfte und verringert die Bruchneigung, wodurch sich die Handhabung an engen Stellen deutlich verbessert. Für Anwender bedeutet das weniger Nacharbeit und höhere Prozesssicherheit beim Bohren in Bleche und Profile. Die kompakte Länge sorgt zudem für besseren Rundlauf in handelsüblichen Bohrfuttern und erhöht so die Ergebnisqualität. Effizientes Bohren dank HSS-G und 135° Spitzenwinkel Das HSS-G Material bietet eine attraktive Kombination aus Zähigkeit und Schnittfestigkeit, die besonders beim Bohren von legierten und unlegierten Stählen Vorteile bringt. Der 135° Spitzenwinkel verkürzt die Anbohrzeit in härteren Werkstoffen und reduziert das Auswandern des Bohrers, sodass saubere Lochkanten mit reduziertem Nacharbeiten entstehen. Passend für typische Werkstattanwendungen im Standard-Bereich Mit 6,5 mm Durchmesser fällt dieser Bohrer in den Standard-Bereich, ideal für Werkstatt, Montage und Heimwerkerprojekte. Er ist praxistauglich für dünne bis mittlere Bleche sowie für Profile aus Stahl und Nichteisenmetallen. Für hochpräzise Passungen empfiehlt sich vorheriges Zentrieren, bei sehr tiefen Bohrungen ist mehrstufiges Aufbohren vorteilhaft. Universelle Schaftausführung und einfache Handhabung Der Zylinderschaft erlaubt das Einspannen in normale Dreibackenfutter und macht den Bohrer universell einsetzbar. Anwender profitieren von einfachem Wechsel und guter Kompatibilität mit gängigen Handbohrmaschinen. Beachten Sie, dass bei sehr hohem Drehmoment ein alternatives Schaftprofil besser greifen kann. Materialeignung und typische Einsatzbereiche Diese Ausführung eignet sich für legierten Stahl, unlegierten Stahl, Guss, Temperguss, Sintereisen sowie Hartkunststoff. Die Normalspirale vom Typ N ist die klassische Wahl für Metallbohrungen und liefert verlässliche Spanabfuhr bei kurzen bis mittleren Bohrtiefen. Für filigrane oder sehr tiefe Bohrungen empfehlen sich speziell abgestimmte Werkzeuge. Empfehlung: Für zuverlässige Metallbohrungen in der Werkstatt empfehlen wir den MetavCUT HSS-G Spiralbohrer in extra kurzer Ausführung mit 6,5 mm; bei Fragen zur Anwendung erreichen Sie Metav Werkzeuge per eMail info@metav-werkzeuge.com oder Telefon +49 2822 7131930 Produktmerkmale Artikelnummer: 56065-FDA Marke: MetavCUT Serie: Standard Line Bezeichnung: Spiralbohrer Norm: DIN 1897 Fakten Durchmesser: 6,5 mm Gesamtlänge: 70 mm Spirallänge: 31 mm Spitzenwinkel: 135° Verpackungseinheit: 10 Besonderheiten Material: HSS-G (Schnellarbeitsstahl G für hohe Standzeit) Typ: Typ N (Normalspirale für Metall) Ausführung: extra kurz (verkürzte Gesamtlänge und Arbeitslänge) Schaftausführung: Zylinder (glatter Zylinderschaft, universelles Einspannen) Farbe: blank (bright finished) Für Bohrmaschine: Handbohrmaschine FAQ Für welche Materialien ist der Spiralbohrer von MetavCUT geeignet? Der MetavCUT Spiralbohrer HSS-G Typ N eignet sich für legierten und unlegierten Stahl, Gussstähle, Temperguss, Sintereisen sowie Hartkunststoff und Nichteisenmetalle; die extra kurze Ausführung verbessert dabei die Stabilität bei dünnen Werkstücken. Ist der Zylinderschaft des Spiralbohrers für alle Bohrfutter geeignet? Der Zylinderschaft ist für normale Dreibackenfutter ausgelegt und deshalb sehr universell einsetzbar; bei hohem Drehmoment kann ein anderes Schaftprofil besseren Halt bieten. Kann man mit diesem Bohrer tiefe Löcher bohren? Für sehr tiefe Löcher ist der extra kurze Spiralbohrer weniger geeignet; bei tiefen Bohrungen empfiehlt sich mehrstufiges Aufbohren oder spezielle Langbohrer, da die Spirallänge die Spanabfuhr begrenzt. Welche Vorteile bringt die extra kurze Ausführung beim Bohren in Bleche? Die extra kurze Ausführung reduziert Hebelkräfte und Verdrehungen, was die Bruchanfälligkeit verringert und besonders beim Bohren in dünnen Blechen oder engen Einbausituationen saubere Ergebnisse liefert. Welche SKU hat der Bohrer für Nachbestellungen? Die SKU für diesen Artikel lautet 56065-FDA; bestellen Sie den MetavCUT Spiralbohrer über Metav Werkzeuge oder geben Sie die SKU bei Ihrer Anfrage an.
Why carbide indexable inserts remain the go-to choice
Carbide indexable inserts are the most widely used and versatile cutting inserts in machining. Manufactured from a sintered mixture of hard particles such as tungsten carbide and a metallic binder like cobalt, these inserts form the actual cutting edge on toolholders including milling cutters, turning inserts and drills. Synonyms used here: carbide cutting inserts, indexable carbide inserts.
How they perform under coolant and load
As the cutting element, carbide indexable inserts enable economic and precise machining across a broad spectrum of materials, from soft non‑ferrous metals to high‑strength steels. In tool systems without internal cooling, heat generated at the cutting zone is normally removed by external machine nozzles using coolant, which is adequate for most standard tasks, open contours and easily accessible components. For deep holes, heavy roughing or when working with materials that generate high temperatures such as stainless steel or titanium alloys, the use of internal cooling is essential: coolant is delivered through internal channels in the toolholder directly to the cutting edge under pressure to prevent thermal overload, optimise chip formation and extend insert life.
Key performance gains you can expect
- increased tool life through the high wear resistance and balanced toughness of tungsten carbide inserts
- consistent chip control and surface finish when coolant is delivered precisely via internal channels
- reduced machine downtime thanks to easy indexability and fast insert changes on compatible toolholders
- broad material compatibility, from soft non‑ferrous metals to hardened steels, enabling fewer tool variants in stock
- economic productivity by combining long stand life with repeatable cutting performance
Metav as your precision partner
Metav stands for the democratisation of precision. With decades of expertise and a catalogue that spans from high‑precision measuring instruments to full workshop equipment, Metav acts as a reliable quality filter for the European market from its Emmerich location. Over 48,000 customers trust Metav’s range and service; the breadth of more than 250,000 products helps reduce supplier complexity while ensuring consistent supply and product quality for industry and trade.
In brief: carbide indexable inserts at a glance
Carbide indexable inserts deliver the necessary balance of extreme wear resistance and mechanical toughness for versatile, cost‑efficient machining. Used with appropriate coolant strategy—external coolant for general work and internal cooling for demanding, deep or heat‑intensive operations—they are a cornerstone of modern metalcutting.
FAQ
What are carbide indexable inserts made of?
Carbide indexable inserts are manufactured from a sintered mixture of hard particles such as tungsten carbide and a metallic binder like cobalt, producing a cutting material that combines high wear resistance with the toughness needed to resist mechanical shock.
When is internal cooling necessary for carbide cutting inserts?
Internal cooling becomes necessary for deep hole drilling, heavy roughing and when machining materials that generate significant heat, such as stainless steel or titanium alloys. Internal cooling channels in the toolholder deliver coolant directly to the cutting edge to prevent thermal overload and improve chip breakage.
Can indexable carbide inserts be used without internal cooling?
Yes. For most standard applications, open contours and well‑accessible components, external coolant supplied by machine nozzles is sufficient, as tungsten carbide is more tolerant of moderate temperature fluctuations than some alternative materials.
How do carbide indexable inserts contribute to production efficiency?
By offering long tool life, stable cutting performance and quick indexability on compatible toolholders, indexable carbide inserts help reduce downtime, simplify tool inventories and maintain consistent part quality across varying materials.
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com