Carbide indexable inserts for high‑performance metalworking
Carbide indexable inserts are wear‑resistant cutting elements designed to deliver economical, precise material removal across a wide range of workpieces, offering excellent balance between extreme wear resistance and the toughness required to withstand mechanical shocks. Used on toolholders such as cutters, turning tools and twist drills, they enable efficient machining of materials from soft non‑ferrous alloys to high‑strength steels by optimising cutting forces and thermal stability. For standard accessible contours external coolant is often sufficient, while deep holes, heavy cutting or machining of stainless steel and titanium alloys benefit from internal coolant channels to protect the cutting edge, improve chip control and extend insert life. Key advantages include high durability, consistent surface finish and reduced tool changeover times through the use of replaceable indexable inserts, carbide grades and toolholder systems.
7.4mm HSS-G Twist Drill DIN 338 ,short, bright finished, Type N - MetavCUT
Hohe Stabilität durch kurze Ausführung, schnelle Schnittfortschritte dank geschliffener HSS‑G Geometrie und der 135° Spitzenwinkel machen diese Lösung besonders wirtschaftlich für anspruchsvolle Metallbohrungen. Bestellen Sie den Spiralbohrer direkt über Metav und kontaktieren Sie unsere Beratung bei technischen Fragen. Spiralbohrer kurz HSS‑G 7,4 mm »Standard Line« von MetavCUT Der Spiralbohrer ist ein kurz ausgeführter, geschliffener HSS‑G Bohrer für präzise Metallbohrungen an Handbohrmaschine und stationären Maschinen HSS‑G geschliffener Spiralbohrer für Metall Kurze Ausführung für höhere Stabilität Spitzenwinkel 135° für harte Werkstoffe Geeignet für Handbohrmaschine und stationäre Maschinen DIN 338 Norm, Zylinderschaft, SKU 45074‑FDA Stabilität und Effizienz bei der Metallbearbeitung Die kurze Ausführung reduziert das Auskragen aus dem Bohrfutter und erhöht so die Stabilität während des Bohrens. Durch die geschliffene HSS‑G Geometrie werden scharfe Schneiden und eine hohe Rundlaufgenauigkeit erzielt, was zu saubereren Bohrlöchern führt und das Nacharbeiten minimiert. Das Resultat ist ein spürbarer Produktivitätsgewinn: bis zu 40 % schnelleres Bohren bei gleichzeitig 50 % weniger Anpresskraft gegenüber konventionellen HSS‑Ausführungen. Material und Fertigungsqualität für saubere Bohrlöcher Gefertigt aus HSS‑G (Schnellarbeitsstahl, geschliffen) bietet der Werkstoff die Zähigkeit und Schneidhaltigkeit, die für legierte und unlegierte Stähle, Gusswerkstoffe und Nichteisenmetalle erforderlich ist. Der CNC‑Schliff sorgt für exakte Spanräume und scharfe Kanten, die den Spanabtransport verbessern und die Lochqualität erhöhen. Beachten Sie, dass geschliffene Bohrer empfindlicher gegenüber seitlichen Kräften sind; deshalb ist der Einsatz an stabiler Aufnahme und mit geeigneter Kühlung empfohlen. Empfohlenes Einsatzfeld und Maschinenvoraussetzungen Mit einem Durchmesser von 7,4 mm ordnet sich der Bohrer in den Standard‑Bereich ein und eignet sich für Werkstatt, Montage und viele DIY‑Anwendungen. Direktes Bohren ist möglich; für höchste Präzision empfiehlt sich das Anpunkten mit einem Zentrierbohrer. Der Bohrer passt sowohl in Handbohrmaschine als auch in stationäre Säulenbohrmaschinen, liefert aber die besten Ergebnisse bei stabiler Spannmittelaufnahme und moderater Drehzahl, ergänzt durch Kühlschmierstoff bei gehärteten Werkstoffen. Zielgruppe und Vorteile für Werkstatt und Produktion Konzipiert für Werkstätten, Instandhaltung und Fertigung, bietet diese Ausführung eine robustere Handhabung bei gleichzeitig hoher Bohrqualität. Die Kombination aus kurzer Ausführung, geschliffenem HSS‑G und 135° Spitzenwinkel reduziert Ausschuss und erhöht Durchsatz bei Serienarbeiten. Die Verpackungseinheit mit mehreren Stück eignet sich zur Bevorratung in Werkstatt und Montage, so dass Maschinenstillstand minimiert wird. Für präzise Metallbohrungen empfehlen wir den HSS‑G Kurzbohrer von MetavCUT als wirtschaftliche Wahl; bestellen Sie über Metav und lassen Sie sich bei Bedarf technisch beraten unter info@metav-werkzeuge.com oder telefonisch +49 2822 7131930 Produktmerkmale Artikelnummer: 45074-FDA Marke: MetavCUT Bezeichnung: Spiralbohrer Serie: Standard Line Fakten Durchmesser: 7,4 mm Gesamtlänge: 109 mm Spirallänge: 69 mm Spitzenwinkel: 135° Verpackungseinheit: 10 Besonderheiten Material: HSS‑G (Schnellarbeitsstahl) Schaftausführung: geschliffen Ausführung: kurz Norm: DIN 338 Typ: Typ N Farbe: blank Für Bohrmaschine: Handbohrmaschine FAQ Für welche Werkstoffe eignet sich dieser Bohrer am besten? Der Spiralbohrer von MetavCUT (SKU 45074‑FDA) eignet sich besonders für legierte und unlegierte Stähle, Gussstahl, Gusseisen, Sintereisen, Temperguss, Nichteisenmetalle und Hartkunststoff. Kann der Bohrer in einer Handbohrmaschine verwendet werden? Ja, der HSS‑G Kurzbohrer ist für die Nutzung an Handbohrmaschine geeignet, liefert aber die besten Resultate bei stabiler Aufnahme und moderater Drehzahl. Was bedeutet HSS‑G geschliffen und welche Vor‑ und Nachteile hat das? HSS‑G steht für geschliffenen Schnellarbeitsstahl; der Schliff sorgt für scharfe Schneiden und hohe Rundlaufgenauigkeit, was saubere Bohrlöcher ermöglicht. Nachteilig ist eine erhöhte Empfindlichkeit gegenüber seitlichen Kräften, daher empfiehlt sich Kühlung und eine stabile Spannmittelaufnahme. Warum ist ein Spitzenwinkel von 135° vorteilhaft? Ein Spitzenwinkel von 135° reduziert die Anbohrdauer und eignet sich besonders für harte Werkstoffe wie Edelstahl und gehärtete Stähle, da er die Schneidenbelastung verteilt und den Vorschub erleichtert. Wie verlängert man die Lebensdauer des Bohrers? Durch richtige Drehzahlwahl, Einsatz von Kühlschmierstoff bei gehärteten Werkstoffen, ggf. Anpunkten mit Zentrierbohrer und die Vermeidung seitlicher Belastungen kann die Lebensdauer des Spiralbohrers von MetavCUT deutlich erhöht werden.
7.4mm HSS-G Twist Drill DIN 338 ,short, bright finished, Type N - MetavCUT
Die Kombination aus hoher Präzision und robuster Stabilität macht diesen Bohrer zur effizienten Lösung für Metallbearbeitung; profitieren Sie von schnellerem Vorschub und geringerer Anpresskraft und bestellen Sie den Spiralbohrer direkt über Metav oder fragen Sie unsere Beratung an. Spiralbohrer Kurzausführung HSS-G von MetavCUT Spiralbohrer Kurzausführung HSS-G für präzise Metallbohrungen an Handbohrmaschine und stationären Geräten Hohe Spürbarkeit bei harten Werkstoffen dank kurzer Auskraglänge Geschliffene Geometrie für besonders saubere Bohrlöcher Geeignet für Handbohrmaschine und stationäre Bohrmaschinen 135° Spitzenwinkel für Bearbeitung von Edelstahl Profi Line Ausführung von MetavCUT Robustheit und Materialvorteile für längere Standzeiten Der kurz ausgeführte HSS-G Bohrer überzeugt durch HSS-G Material und geschliffene Schneiden, die eine sehr scharfe Kante und hohe Rundlaufgenauigkeit liefern. Diese Kombination reduziert die erforderliche Anpresskraft um bis zu 50 % und ermöglicht ein bis zu 40 % schnelleres Bohren gegenüber herkömmlichen HSS-Varianten. Das Ergebnis ist ein deutlich reduzierter Kraftaufwand bei gleichbleibender Bohrlochqualität und eine geringere Belastung von Maschine und Werkstück. Präzise Anwendung im Standard-Bereich für Werkstatt und Montage Mit einem Durchmesser von 7,4 mm liegt dieser Bohrer im Standard-Bereich, ideal für Werkstatt, Montage und allgemeine Metallbearbeitung. Die kurze Ausführung minimiert Vibrationen und Wandern beim Anbohren, sodass auch Handgeführte Bohrmaschinen zuverlässig zum Einsatz kommen können. Die Geometrie eignet sich für legierten und unlegierten Stahl, Gusseisen sowie Nichteisenmetalle und ermöglicht saubere, präzise Bohrungen bei normalen bis mittleren Bohrtiefen. Maschinenverträglichkeit und sichere Handhabung Die kürzere Auskraglänge und die volle Schaftgeschliffen-Ausführung erhöhen die Stabilität im Spannfutter und reduzieren Verbiegen und Bruchrisiko. Für optimale Ergebnisse empfiehlt sich der Einsatz mit geeigneter Kühlung bei zähen Materialien und das Anpunkten bei höheren Präzisionsanforderungen. Aufgrund der geschliffenen Fertigung ist der Bohrer besonders scharf, aber sensitiver gegenüber Schlägen, daher bei stationären Maschinen und kontrolliertem Vorschub besonders wirtschaftlich. Normkonformität, Spitzenwinkel und Anwenderhinweise Die Einhaltung der DIN 338 sowie die Auslegung als Typ N mit 135° Spitzenwinkel macht den Bohrer zur guten Wahl für härtere Werkstoffe wie Edelstahl, da der größere Spitzenwinkel die Anbohrzeit verkürzt und das Eindringen erleichtert. Anwender profitieren von der Profi Line Verarbeitung durch MetavCUT, die für konstante Qualität steht. Beachten Sie bei Einsatz in weichen Kunststoffen die passende Vorschub- und Drehzahlwahl, um Ausrisse zu vermeiden. Empfehlen Sie den MetavCUT Profi Line HSS‑G Spiralbohrer für präzise Metallbohrungen und kontaktieren Sie uns bei Unsicherheiten per eMail info@metav-werkzeuge.com oder Telefon +49 2822 7131930, alternativ WhatsApp +49 170 2837271. Produktmerkmale Artikelnummer: 48074-FDA Marke: MetavCUT Bezeichnung: Spiralbohrer Modellserie: Profi Line Typ: Typ N Material: HSS-G Norm: DIN 338 Fakten Durchmesser: 7,4 mm Gesamtlänge: 109 mm Spirallänge: 69 mm Spitzenwinkel: 135° Verpackungseinheit: 10 Besonderheiten Ausführung: kurz Schaftausführung: geschliffen (G = geschliffen: sehr scharfe Kanten, hohe Präzision) Farbe: blank Für Bohrmaschine: Handbohrmaschine Anwendung: Bohrer für Metall Hersteller: MetavCUT Serie: Profi Line FAQ Ist dieser Bohrer für Edelstahl geeignet? Der Spiralbohrer von MetavCUT (Profi Line, Typ N, SKU 48074-FDA) ist mit einem 135° Spitzenwinkel ausgelegt und eignet sich gut für die Bearbeitung von Edelstahl bei angepasster Drehzahl und Kühlung. Kann ich den Bohrer mit einer Handbohrmaschine verwenden? Ja, die kurze Ausführung des HSS‑G Bohrers ist speziell dafür geeignet, Vibrationen und Verbiegen zu minimieren, sodass Handbohrmaschinen für normale Bohrtiefen eingesetzt werden können. Welche Werkstoffe bearbeitet der Bohrer zuverlässig? Der MetavCUT HSS‑G Spiralbohrer ist geeignet für legierten und unlegierten Stahl, Gusseisen, Sintereisen, Temperguss, Nichteisenmetalle und Hartkunststoffe. Wie unterscheidet sich die geschliffene Ausführung von gewalzten Bohrern? Geschliffene (HSS‑G) Bohrer bieten sehr scharfe Schneiden und hohe Rundlaufgenauigkeit, was saubere Bohrlöcher ermöglicht; sie können jedoch spröder sein als gewalzte Varianten und profitieren von kontrollierter Kühlung. Welche Vorteile bietet die Profi Line Serie von MetavCUT? Die Profi Line Serie kombiniert normgerechte Fertigung nach DIN 338 mit gehobener Material- und Oberflächenqualität, was zu konstanteren Ergebnissen und längeren Standzeiten führt.
7.5mm HSS Twist Drill DIN 338 ,short, roll forged, black, Type N - MetavCUT
Twist Drill — Type N short HSS metal drill, 7.5 mm, 118° tip, black, DIN 338, MetavCUT The Twist Drill Type N short HSS bit is a compact metalworking drill designed for hand drills and drilling machines, delivering stable, precise holes in steel, cast iron and non‑ferrous metals. Short Type N design for high stability Suitable for metalworking on drilling machines 7.5 mm diameter with 118° tip for clean starts Made from HSS for long tool life Conforms to DIN 338 for short cylinder‑shank drills Stable precision for demanding metalwork The short construction specified by DIN 338 reduces overhang and dramatically increases rigidity, which means the bit resists bending and produces more accurate holes. As a Type N normal‑spiral tool, this 7.5 mm drill offers predictable chip evacuation and constant cutting geometry—advantages that translate directly into reproducible hole quality and less rework for workshops and maintenance teams. For tasks where repeatability matters, the compact design is the decisive practical benefit. Easier centring and lower feed forces with a 118° tip A 118° tip angle balances fast penetration and reliable centring on typical metal surfaces; the geometry reduces the initial cutting area so the drill starts cleanly without excessive wobble. The tip can be resharpened easily to restore cutting performance, and the reduced querschneide after precision sharpening lowers friction and required feed forces. These characteristics shorten cycle times on hand and bench drills while preserving drill life. HSS material for versatility and resilience Made from HSS (High Speed Steel), this short bit withstands higher temperatures and retains hardness under load, making it suitable for alloyed and unalloyed steels, cast iron, non‑ferrous metals and many plastics. The material choice enables controlled cutting at moderate speeds and allows straightforward resharpening in‑house, which keeps replacement costs down and supports continuous operation in busy workshops. Recommended applications and machine compatibility Built for metal drilling, this bit is optimised for use in Hand Drills and stationary drilling machines where short overhang improves stability. Typical uses include production drilling, maintenance, and repair where a reliable, durable hole is required. The normal spiral makes it less suited for soft‑wood applications but ideal where chip formation and evacuation are critical. For precision work on thin or plated parts, the short length reduces chatter and improves surface finish. Strong recommendation: Choose the MetavCUT short Type N HSS Twist Drill for precise metalworking — METAV Werkzeuge offers expert advice and technical support via 📧 info@metav-werkzeuge.com, ☎️ +49 2822 7131930 or ✔️ WhatsApp +49 170 2837271 Technical Information Bezeichnung: Twist Drill Marke: MetavCUT SKU: 40075-FDA Typ: Type N Durchmesser: 7.5 mm Spitzenwinkel: 118° Ausführung: short Material: HSS Norm: DIN 338 Spirallänge (Flute length): 69 mm Gesamtlänge (Overall length): 109 mm Farbe: black Anwendung: Drills for metal Für Bohrmaschine: Hand Drill / Drilling Machine Bezeichnung (englisch): Twist Drill Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What is a Twist Drill used for and which materials suit this MetavCUT Type N drill? A MetavCUT Twist Drill Type N is primarily used for metalworking; the short HSS design excels when drilling alloyed and unalloyed steel, cast iron, non‑ferrous metals and many plastics, providing reliable chip removal and durable cutting performance. Why are Twist Drills ground to a tip angle like 118°? The 118° geometry on the MetavCUT Type N Twist Drill reduces the cross‑cut at the tip, which lowers friction and feed forces; this sharpening makes centring easier and requires less push during drilling, improving start behavior and precision. For what applications are Twist Drills typically used? Twist Drills are widely applied when machining high‑strength materials and larger diameters; they are easy to resharpen and remain robust under higher loads, which makes the MetavCUT short HSS variant suitable for production and repair work. Which three drill types exist? The main drill categories are metal drills, wood drills and stone/concrete drills; the MetavCUT Type N Twist Drill belongs to the metal drill category and is optimised for those materials. Can a metal drill be used to drill wood? A metal drill, such as the MetavCUT Type N Twist Drill, can be used in wood but generally gives less guidance and a rougher finish compared with dedicated wood bits; however, metal drills are easier to regrind and typically show lower self‑feeding behavior. At which depths is the Twist Drill most commonly used? A full‑bore hole is often executed with a Twist Drill; for diameters up to 20 mm and hole depths up to 100 mm, the short HSS twist drill is among the most commonly used tools. Is HSS or HSSE better? The belief that HSSE steels are categorically superior to HSS is not universally true; evaluate working conditions first—higher cost of HSSE is justified only when the application demands its specific advantages over standard HSS.
7.5mm HSS-E Twist Drill DIN 338 ,short, 5% cobalt-alloyed, Type N - MetavCUT
Nutzen Sie die Kombination aus Präzision, Stabilität und hoher Materialverträglichkeit für verlässliche Metallbearbeitung. Bestellen Sie den Bohrer direkt über Metav oder fordern Sie bei Bedarf technische Beratung an. Spiralbohrer Typ N HSS‑E 7,5 mm von MetavCUT Der Spiralbohrer in kurzer Ausführung eignet sich für präzise Bohrungen in legierten und unlegierten Stahl sowie Gusseisen und Nichteisenmetallen. Kurze Ausführung für hohe Stabilität HSS‑E mit 5% Kobalt für härtere Werkstoffe Geschliffener Schaft für präzise Bohrbilder Spitzenwinkel 135° reduziert Anbohrkräfte DIN 338 konform mit Zylinderschaft Hohe Stabilität durch kurze Auskraglänge und Materialwahl Die kurze Ausführung reduziert die Auskraglänge und führt so zu spürbar höherer Stabilität beim Bohren. Herstellerseitig eingesetztes HSS‑E mit 5% Kobalt erhöht die Warmfestigkeit und verringert Werkzeugverformung bei erhöhten Schnittgeschwindigkeiten. Daraus resultiert eine längere Standzeit und konstante Lochqualität, besonders beim Bearbeiten von Stahl und Edelstahl. Präzision und Oberfläche dank geschliffener Fertigung Durch den geschliffenen Schaft und die CNC‑geschliffene Geometrie entsteht ein exakter Rundlauf und scharfe Schneiden, was saubere Bohrbilder und enge Toleranzen ermöglicht. Anwender profitieren von reduzierter Nacharbeit und besseren Passungen, weil Gratbildung minimiert wird. Diese Eigenschaft macht das Produkt ideal für stationäre und sorgfältige Handarbeiten. Effiziente Zerspanung bei harten Werkstoffen Der Spitzenwinkel 135° sorgt für kontrolliertes Eindringen in härtere Werkstoffe und reduziert das Risiko von Ausbrüchen beim Anbohren. In Verbindung mit der kurzen Bauform erlaubt dies sicheres Bohren ohne übermäßigen Vorschub. Bei Löchern unter 6 mm empfiehlt sich rollgewalzte Elastizität, bei größeren Bohrungen das korrekte Vorbohren nach Industrieregeln. Einsatzbereiche, Maschinen und Anwendernutzen Für Werkstatt, Produktion und anspruchsvolle Heimwerkstatt bietet die Ausführung Vorteile in Stabilität und Standzeit. Die Kombination aus DIN 338‑Normkonformität und Zylinderschaft macht das Produkt kompatibel mit gängigen Bohrfuttern und Säulenbohrmaschinen. Dadurch vereinfacht sich die Lagerhaltung und die Auswahl an Spannfuttern. Anwender erhalten so eine vielseitige Lösung für Serien‑ und Einzelarbeiten. Empfehlung: MetavCUT Standard Line Spiralbohrer für präzise Metallbearbeitung direkt bei Metav beziehen oder technische Beratung per E‑Mail an info@metav-werkzeuge.com bzw. Telefon +49 2822 7131930 anfragen. Produktmerkmale Artikelnummer: 47075-FDA Marke: MetavCUT Serie: Standard Line Bezeichnung: Spiralbohrer Typ: Typ N Material: HSS-E Ausführung: kurz Schaftausführung: geschliffen Farbe: 5% kobaltlegiert Norm: DIN 338 Hersteller: MetavCUT Für Bohrmaschine: Handbohrmaschine Daten Durchmesser: 7,5 mm Gesamtlänge: 109 mm Spirallänge: 69 mm Spitzenwinkel: 135° Verpackungseinheit: 10 Besonderheiten HSS-E: Schnellarbeitsstahl, kobaltlegiert Typ N: Normalspirale, geeignet für Metall Zylinderschaft: kompatibel mit Standardfuttern Geschliffen: CNC‑Schliff für hohe Rundlaufgenauigkeit DIN 338: Norm für kurze Spiralbohrer FAQ Was macht den kurzen Aufbau dieses Bohrers besonders vorteilhaft? Die kurze Ausführung reduziert die Auskraglänge und erhöht dadurch die Stabilität; der MetavCUT Standard Line Spiralbohrer liefert so bessere Lochqualität und geringere Vibrationen bei Metallbohrungen. Eignet sich der Bohrer für Edelstahl? Ja, durch den Spitzenwinkel 135° und die HSS‑E‑Legierung mit 5% Kobalt ist der Spiralbohrer für anspruchsvollere Werkstoffe wie Edelstahl geeignet, wenn mit geeigneter Kühlung gearbeitet wird. Kann der Bohrer in handelsüblichen Handbohrmaschinen verwendet werden? Der Bohrer ist für Handbohrmaschine ausgelegt und besitzt einen Zylinderschaft nach DIN 338, wodurch er in den meisten Spannfuttern sicher eingespannt werden kann. Worin unterscheidet sich diese geschliffene Ausführung von rollgewalzten Bohrern? Geschliffene Bohrer bieten höhere Schärfe und Rundlaufgenauigkeit, was präzise Bohrbilder ermöglicht; rollgewalzte Varianten sind oft elastischer und weniger spröde, was bei sehr kleinen Durchmessern vorteilhaft sein kann. Welche Pflege‑ oder Betriebsbedingungen verlängern die Standzeit? Regelmäßige Kühlung, moderater Vorschub und das Vorbohren bei größeren Durchmessern reduzieren Wärmebelastung und Spanklemmung, was die Standzeit des MetavCUT Spiralbohrers erhöht.
7.5mm HSS-G Twist Drill DIN 1869 ,extra long, bright finished - MetavCUT
Twist Drill — HSS‑G extra long Twist Drill, 7.5 mm, 135° tip, bright finished, fully ground shank, DIN 1869 The Twist Drill extra long HSS‑G is a specialist drill for Drilling Machine applications, engineered for deep and demanding metal drilling tasks. Extra long design for deep hole access 135° tip for harder materials and quick entry HSS‑G ground geometry for precise, clean holes Fully ground shank for high concentricity Suited for drilling in alloyed and unalloyed steels Deep drilling reach for confined or deep workpieces The Extra Long configuration and an overall length of 225 mm combined with a spiral length of 155 mm allow access to deep or hard‑to‑reach drill positions, so fewer tool changes are required. This design makes it easier to create long, straight holes in components where standard lengths fall short. For users who need extended reach during maintenance, workshop or production drilling, the extended geometry increases flexibility without sacrificing control. Faster cutting with ground HSS‑G geometry and reduced feed forces The HSS‑G material and CNC ground flutes deliver sharp cutting edges and excellent roundness, which translate into up to 40% faster drilling and roughly 50% lower feed force compared with conventional HSS types under comparable conditions. This benefit reduces operator effort and can improve cycle times in repetitive machining tasks. The ground construction also produces cleaner chips and more accurate hole diameters, which is especially advantageous for subsequent reaming or finishing operations. Optimised for harder metals and machine use A 135° tip angle is selected to perform reliably in harder materials such as stainless steels and tempered steels; the larger tip angle shortens the initial plunge time and improves centring on difficult surfaces. The MetavCUT Twist Drill is specified to meet DIN 1869 and is particularly recommended for use in Drilling Machines with adequate cooling. As the ground variant can be more brittle than rolled types, machine mounting and coolant are advised to maximise tool life and avoid breakage under heavy loads. Clear benefits for workshops, maintenance and production Customers in metalworking, toolrooms and industrial maintenance gain from consistent hole quality and reduced rework. The combination of bright finished surface and fully ground shank improves clamping stability and runout, which benefits hole accuracy and tool longevity. For users requiring reliable deep-hole machining with predictable results, this HSS‑G Twist Drill by MetavCUT offers a balance of precision and reach while conforming to recognised standards. MetavCUT Twist Drill recommended for demanding deep metal drilling — for individual technical advice METAV Werkzeuge provides competent support: info@metav-werkzeuge.com | +49 2822 7131930 | WhatsApp +49 170 2837271 Designation: Twist Drill Brand: MetavCUT SKU: 32075-FDA Diameter: 7.5 mm Tip angle: 135° Material: HSS‑G Execution: Extra long Spiral length: 155 mm Overall length: 225 mm Shank finish: Fully ground Colour: Bright finished Intended for: Drilling for metal / Drilling Machine Standard: DIN 1869 Applications: Alloyed and unalloyed steel, cast iron, non‑ferrous metals, hard plastics Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What is the MetavCUT Twist Drill used for and where does it perform best? The MetavCUT Twist Drill is primarily used for drilling metal and is optimised for deep holes and tougher materials; it performs best in machine applications such as Drilling Machines where the extra length and HSS‑G ground geometry enable precise, deep bore creation in alloyed and unalloyed steels, cast materials and hard plastics. Which three drill types exist? The main categories are Metal Drills, Wood Drills and Stone/Concrete Drills; the MetavCUT Twist Drill belongs to the Metal Drills group and is designed for metalworking tasks. Why are Twist Drills point‑ground? The point grinding reduces the cross‑cut at the tip, lowering friction and therefore requiring less feed force; this improves centring in the workpiece and reduces the risk of wandering, which is a key reason the MetavCUT Twist Drill is ground for high‑precision metal drilling. Can a metal drill be used for wood? A Metal Drill such as the MetavCUT Twist Drill can be used in wood, but guidance and finish are usually inferior compared with purpose‑made wood drills; metal drills are easier to resharpen and have less aggressive self‑feed, so results can be acceptable for non‑critical wooden jobs. At which depths is the Twist Drill most commonly used? For solid drilling, Twist Drills are typical up to diameters of about 20 mm and depths up to 100 mm; the MetavCUT Extra Long variant is intended for deeper or harder‑to‑access hole requirements where standard lengths would be insufficient. What is better, HSS or HSSE? There is no universal rule that HSSE is always superior to HSS; the choice depends on working conditions, material and cost considerations. Evaluate whether the specific machining demands justify the higher investment in HSSE for your application.
7.5mm HSS-G Twist Drill DIN 1869 ,extra long, bright finished - MetavCUT
Twist Drill — Extra long HSS‑G 7.5 mm, 135° Point, Bright Finished (DIN 1869) by MetavCUT The Twist Drill is an extra‑long HSS‑G drill designed for deep metal drilling in a Drilling Machine and for demanding machining tasks. Extra‑long design for deep drilling HSS‑G material for high precision metalwork 135° point angle for harder materials Fully ground shank for accurate runout Conforms to DIN 1869 for industrial use Durable HSS‑G construction for precision and life The Twist Drill is manufactured from HSS‑G (ground high‑speed steel), which provides high cutting performance and precise hole quality in metalworking. Ground flutes create very sharp cutting edges and superior concentricity, resulting in cleaner holes and lower vibration. This construction suits applications where drilling accuracy matters and supports stable tool behaviour under machining loads. Extra‑long geometry for deep and hard-to-reach holes With an extra‑long overall length and an extended spiral length, this twist drill enables reliable drilling in deep bores and in situations where access is limited. The longer geometry reduces the need for extensions or special setups, allowing deeper penetration while maintaining chip evacuation. For deep drilling, pair the tool with appropriate cooling to reduce thermal stress and prolong tool life. Point geometry optimised for harder materials A 135° point angle is specified to improve centring and reduce chipping when working with harder metals such as alloyed steels and cast materials. The flatter tip reduces initial cutting forces and helps maintain tool life under higher contact stresses. This geometry is especially suitable when accuracy and clean entry holes are required in tough workpiece materials. Application range and recommended use This twist drill is intended primarily for Drills for metal, including alloyed and unalloyed steel, cast steel, cast iron and certain engineering plastics. The fully ground shank ensures low runout when used in standard drilling machines. For best results, operate with appropriate coolant, moderate feed rates and stable clamping. Where mobility is required, ensure correct speeds and support to avoid breakage. Who benefits from this tool Engineers, toolroom technicians and maintenance professionals who need a reliable solution for deep, precise metal holes will benefit from the Twist Drill’s combination of extra length, ground geometry and robust HSS‑G material. The tool is suitable for both production environments and repair operations where hole quality and repeatability are priorities. For demanding deep‑hole metal machining choose MetavCUT’s Twist Drill for consistent performance — METAV Werkzeuge offers expert advice and support via info@metav-werkzeuge.com, phone +49 2822 7131930 or WhatsApp +49 170 2837271 Twist Drill Brand: MetavCUT SKU: 33075-FDA Diameter: 7.5 mm Point angle: 135° Execution: Extra long Colour: Bright finished Material: HSS‑G Standard: DIN 1869 Spiral (Flute) length: 200 mm Overall length: 290 mm Shank finish: Fully ground For use in: Drilling Machine Application: Drills for metal Model series: Standard Line Manufacturer: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What materials can the MetavCUT Twist Drill be used on? The MetavCUT Twist Drill is designed for a wide range of metals; it performs well in alloyed and unalloyed steels, cast steel, cast iron and some hard plastics thanks to its HSS‑G material and 135° point geometry. Is the MetavCUT Twist Drill suitable for deep boring in production? Yes, the MetavCUT Twist Drill’s extra‑long design and DIN 1869 compliant flute geometry make it suitable for deep bore applications in production environments when used with proper cooling and stable clamping. For what is a Twist Drill used? A Twist Drill is mainly applied for machining high‑strength materials and larger diameters. Its design is straightforward to regrind and it withstands higher loads, making it suitable for demanding metalworking tasks. Which three drill types exist? There are Metal Drills, Wood Drills and Stone/Concrete Drills. Why are twist drills pointed (regrinded)? Pointing reduces the secondary cutting edge at the tip, which lowers friction and required feed forces while improving centring of the drill in the workpiece. Can a metal twist drill be used to drill wood? A metal twist drill can be used in wood but typically has poorer guidance and a less clean finish; however, such drills are easier to resharpen and exhibit less self‑feed. For which depths is the twist drill most commonly used? Solid drilling is often performed with twist drills. For diameters up to 20 mm and drilling depths up to 100 mm, the twist drill is the most commonly used tool. Is HSS or HSSE better for my needs? The common belief that HSSE is always superior to HSS is not universally correct. Assess whether your working conditions justify the higher cost of HSSE before selecting the tool.
7.5mm HSS-G Twist Drill DIN 1869 ,extra long, bright finished - MetavCUT
Twist Drill (Drill Bit) — MetavCUT Extra Long HSS‑G, 7.5 mm, 135° Point Angle, Bright Finished, Fully Ground, DIN 1869 The Twist Drill by MetavCUT is an extra‑long HSS‑G drill bit designed for deep metal drilling in drilling machines, combining increased reach with precise, ground geometry for reliable industrial use. Extra‑long design for deep hole drilling HSS‑G material for higher cutting performance 135° Point Angle optimized for hard metals Fully ground shank for excellent concentricity Conforms to DIN 1869 for demanding conditions Engineered reach and reliability for deep drilling This extra‑long Twist Drill delivers extended reach where standard lengths fall short. The increased Overall Length and Spiral Length make it suitable for deep Holes and hard‑to‑access bore positions, reducing the need for extensions or special fixtures. Because the Flute Geometry is produced by CNC grinding, the bit offers consistently sharp cutting edges and improved chip evacuation, which helps maintain cutting performance over longer penetrations and under higher loads. Ground geometry for precise, clean holes The Fully Ground HSS‑G construction results in very accurate concentricity and sharp cutting lips, producing cleaner bores in metal. A 135° Point Angle reduces walking and spreads cutting forces for tougher materials such as alloyed and unalloyed steels. For users, this means fewer re‑drills, better hole quality and improved fitment for subsequent assembly operations. Use with appropriate coolant and steady feed to avoid brittle breakage tendencies common to ground HSS tools. Material choice and what it means for performance Constructed from HSS‑G, this bit balances hardness and wear resistance with the grindability required for precision tools. HSS‑G is particularly suited to metalworking tasks—casting, steel, sintered materials and certain plastics—where a sharp, ground flute profile improves hole finish. For those less familiar: HSS‑G indicates a High Speed Steel tool that has been ground (G) rather than roll‑formed, giving superior edge geometry and surface finish at the expense of slightly higher brittleness. Recommended use cases and handling advice Best results are achieved when the bit is used in a suitable Drilling Machine with stable clamping, controlled feed and coolant. The extra length is designed for deep bores up to substantial depths while preserving accuracy; avoid excessive side loads and use reduced speeds for very hard materials. When regrinding is necessary, the ground geometry allows relatively simple resharpening, but caution is advised to maintain the correct Point Angle and lip geometry to preserve centring and cutting behaviour. Who benefits from this tool and why This tool is aimed at professional workshops and industrial fabricators who require reliable deep drilling in metals. The combination of DIN 1869 compliance, fully ground shank and extra‑long design makes it a practical choice for machinists tackling components with recessed or hard‑to‑reach bore locations. For users seeking cleaner holes and consistent tool life in challenging materials, the HSS‑G extra‑long design provides a measurable advantage. Strong recommendation: For demanding metalworking applications choose the MetavCUT extra‑long HSS‑G Twist Drill for superior reach and hole quality — METAV Werkzeuge offers comprehensive expert advice and technical support by email at info@metav-werkzeuge.com, by phone at +49 2822 7131930 or via WhatsApp at +49 170 2837271 if additional data or application guidance is required Technical Information Designation: Twist Drill Brand: MetavCUT SKU: 34075-FDA Diameter: 7.5 mm Overall Length: 370 mm Spiral Length: 250 mm Point Angle: 135° Material: HSS‑G Standard: DIN 1869 Execution: Extra long Finish: Bright finished Shank: Fully ground Model Series: Standard Line Suitable For: Drilling Machine Applications: Drills for metal Manufacturer: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What is the MetavCUT Twist Drill used for and which materials suit it best? The MetavCUT Twist Drill (drill bit) is primarily used for drilling in metal; it is especially effective on alloyed and unalloyed steel, cast iron, sintered metals, temper cast and non‑ferrous metals, as well as hard plastics where a precise bore is required. Which three main drill types exist? The primary drill categories are metal drills, wood drills and stone/concrete drills, covering the typical material families and tool geometries needed for different substrates. For what purpose are twist drills mainly used? Twist Drills are mainly applied to machining high‑strength materials and larger drill diameters; their form is easy to regrind and they withstand higher loads while maintaining hole quality. Why are twist drills pointed (what is the purpose of the point)? Pointing reduces the secondary cutting edge at the tip; by resharpening the point, friction is lowered, which reduces required feed forces and improves centring of the tip in the workpiece for more accurate starts. Can the MetavCUT Twist Drill be used to drill wood? A metal‑grade twist drill can be used in wood, but guidance and surface finish are generally inferior compared with dedicated wood bits. The metal bit is easier to resharpen and has lower self‑feeding tendency. At which drilling depths is the twist drill most commonly used? Solid hole drilling is typically performed with a twist drill. For diameters up to about 20 mm and depths up to around 100 mm, the twist drill is the most frequently used tool. What is better, HSS or HSSE? The common belief that HSSE is always superior to HSS is not universally true. Evaluate working conditions carefully to determine whether the higher cost of HSSE is justified for your application.
7.5mm HSS-G Twist Drill DIN 338 ,left cutting - MetavCUT
Spiralbohrer von MetavCUT – Profi Line (HSS-G, DIN 338) Der Spiralbohrer ist ein linksschneidender Kurzspiralbohrer aus HSS-G für präzise Metallbohrungen an Handbohrmaschine und stationären Maschinen. Linksschneidend für Ausbohren festsitzender Schrauben HSS-G: hohe Wärme- und Verschleißfestigkeit Kurzspiralbohrer gemäß DIN 338 für stabile Führung Spitzenwinkel 135° für harte Werkstoffe Geeignet für Handbohrmaschine und Werkstattbetrieb Schnellere Bohrung bei reduziertem Kraftaufwand Der linksschneidende, geschliffene Kurzspiralbohrer ermöglicht beim Bohren in Stahl und Guss oft ein bis zu 40 % schnelleres Arbeiten und reduziert die benötigte Anpresskraft um etwa 50 %. Diese Kombination führt zu kürzeren Taktzeiten in der Werkstatt und entlastet die Maschine sowie den Anwender. Durch die geometrische Abstimmung der Schneiden wird zudem das Verhaken an festsitzenden Schrauben vermindert, was Reparatur- und Montageprozesse deutlich vereinfacht. Materialqualität und Normsicherheit für langlebige Werkzeuge Gefertigt aus HSS-G bietet der Bohrer eine hohe Verschleißfestigkeit und gute Warmhärte, was besonders bei intermittierendem Schneiden in legierten Stählen vorteilhaft ist. Die Einhaltung von DIN 338 garantiert kurze Spiralbohrer mit Zylinderschaft und erleichtert die Auswahl für standardisierte Maschinenaufnahmen. Für Anwender bedeutet das: geringere Ausfallzeiten durch Austausch und planbare Ersatzteilkonfigurationen in der Werkstatt. Vielseitige Einsatzgebiete und passende Maschinenklasse Mit einem Durchmesser von 7,5 mm liegt der Bohrer im Standard-Bereich und eignet sich besonders für Werkstattarbeiten, Montage sowie DIY-Projekte an dünnen bis mittleren Blechen und Flachstählen. Die Konstruktion passt zu Handbohrmaschine und stationären Säulenbohrmaschinen; bei höherer Präzision empfiehlt sich zuvor ein Zentrierpunkt. Für tiefe Sacklochbohrungen oder gehärtete Serienteile sind alternative Verfahren wirtschaftlicher. Anwendungshinweise und Vorsichtsmaßnahmen Da der Bohrer linksschneidend ist, wird für den korrekten Schnitt ein Linkslauf der Bohrmaschine benötigt; beim Ausbohren festsitzender Schrauben kann diese Drehrichtung den Schraubenrest herausdrehen. Der Spitzenwinkel 135° reduziert das Anlaufen in harten Werkstoffen und verbessert die Zentrierung. Kühlung und geeignete Schnittgeschwindigkeit verlängern die Standzeit; bei Unsicherheit zur Werkstoffwahl empfiehlt sich ein Testbohrung an Restmaterial. Empfehlung: Vertrauen Sie auf die MetavCUT Profi Line für zuverlässige Metallbearbeitung; bei Rückfragen erreichen Sie uns per eMail info@metav-werkzeuge.com oder Telefon +49 2822 7131930. Produktmerkmale Artikelnummer: 60075-FDA Marke: MetavCUT Serie: Profi Line Bezeichnung: Spiralbohrer Fakten Durchmesser: 7,5 mm Spitzenwinkel: 135° Verpackungseinheit: 10 Besonderheiten Ausführung: linksschneidend Material: HSS-G (Schnellarbeitsstahl) Norm: DIN 338 (kurze Spiralbohrer mit Zylinderschaft) Für Bohrmaschine: Handbohrmaschine Modellserie: Profi Line FAQ Ist der Bohrer für Edelstahl geeignet? Der MetavCUT Profi Line Spiralbohrer mit 135° Spitzenwinkel eignet sich für härtere Werkstoffe wie Edelstahl, da der größere Spitzenwinkel die Anbohrkraft reduziert und die Zentrierung verbessert. Welche Maschine wird empfohlen? Für den Durchmesser 7,5 mm ist eine Handbohrmaschine oder eine stationäre Säulenbohrmaschine geeignet; bei besonders präzisen Passungen sollte vorab angepunktet werden. Wofür ist die linksschneidende Ausführung nützlich? Die linksschneidende Geometrie hilft beim Ausbohren festsitzender Schrauben, weil die linke Drehrichtung den Schraubenrest beim Bohren oft mit herausdreht. Wie lange hält der HSS-G Bohrer bei Normalbetrieb? Die Standzeit hängt vom Werkstoff und der Schnittbedingung ab; HSS-G bietet jedoch bei intermittierendem Einsatz und geeigneter Kühlung deutlich bessere Verschleißeigenschaften als einfacher Schnellarbeitsstahl. Welche Vorteile bietet die DIN 338 Norm für den Anwender? DIN 338 beschreibt kurze Spiralbohrer mit Zylinderschaft und sorgt für standardisierte Abmessungen und kompatible Maschinenaufnahmen, was die Lagerhaltung und den Austausch erleichtert.
7.5mm HSS-G Twist Drill DIN 338 ,short, bright finished, Type N - MetavCUT
Twist Drill (Drill Bit) – 7.5 mm, 135° tip, Type N, Bright Finished, Short, HSS‑G, DIN 338 by MetavCUT The Twist Drill short Type N drill bit is a precision metalworking drill designed for Drilling Machines, offering a 7.5 mm diameter and a 135° tip angle for robust performance in hard materials. Short Type N design for high stability HSS‑G: up to 40% faster drilling and less feed force 7.5 mm diameter with 135° tip for hard steels Fully ground shank for precise clamping Conforms to DIN 338 for short metal Twist Drills Faster metalworking through optimised HSS‑G performance The HSS‑G material provides a measurable efficiency advantage: according to manufacturer data this fully ground High Speed Steel formulation enables up to 40% faster drilling and requires roughly 50% less feed force compared with conventional HSS bits. This translates into shorter cycle times and reduced operator effort when machining alloyed and unalloyed steels, cast steels, cast iron, sintered iron, tempered castings, non‑ferrous metals and hard plastics. The result is higher productivity in workshops and production environments without sacrificing hole quality. Stability and precision thanks to the short DIN 338 format A short Spiral Length and reduced overhang, as defined by DIN 338, reduce deflection and vibration during drilling. This geometry improves concentricity and hole tolerances on stationary and portable Drilling Machines, making the bit especially suitable where rigidity matters. For precision tasks in metal fabrication or maintenance work, the compact design minimises chatter and bending, delivering cleaner holes and extending tool life through lower mechanical stress. Tip geometry and dimensions engineered for hard materials The 7.5 mm diameter combined with a 135° tip angle is tailored for harder materials such as stainless steel and other tough alloys. A larger tip angle increases the material contact area at the start of the cut, reducing the tendency to grab and shortening the initial penetration time. The Type N normal spiral is the classical metalworking profile, optimised for chip evacuation and consistent cutting in metallic substrates. The bit is bright finished for good surface consistency and chip flow. Secure clamping and simple regrinding for extended use The fully ground cylindrical shank guarantees accurate seating in chucks and collets, supporting repeatable concentricity and uncomplicated tool changes. Compared with rolled shank variants, a ground shank improves grip and reduces slippage under higher torque. Additionally, the straightforward geometry of this Twist Drill allows economical regrinding where appropriate, helping to extend service life and keep workshop costs down while maintaining acceptable hole quality. Practical applications and recommended user groups Designed for robust metalworking tasks, this short Twist Drill suits maintenance technicians, toolroom operatives and industrial workshops that require reliable, repeatable holes in steel and related materials. Its balance of stability, tip geometry and HSS‑G performance makes it a practical choice for production runs on Drilling Machines as well as precise repair and retrofit jobs where reduced runout and clean entry are important. METAVCUT’s Basic Line positions this bit as a dependable everyday tool for demanding metal applications. Strong recommendation from MetavCUT: choose this HSS‑G short Twist Drill for reliable metalworking performance, and contact METAV Werkzeuge for expert technical advice and application support — 📧 info@metav-werkzeuge.com — ☎️ +49 2822 7131930 — ✔️ WhatsApp +49 170 2837271 Twist Drill (Short Type N) Brand: MetavCUT SKU: 27075-FDA Diameter: 7.5 mm Tip angle: 135° Material: HSS‑G Norm: DIN 338 Execution: Short Spiral length: 69 mm Total length: 109 mm Shank: Fully ground Colour/Finish: Bright finished For machine: Drilling Machine Application: Drills for metal Model series: Basic Line Manufacturer: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What materials is the Twist Drill by MetavCUT suitable for and where is it best used? The MetavCUT Twist Drill short Type N is intended primarily for metalworking; its HSS‑G composition and Type N spiral make it well suited to alloyed and unalloyed steels, cast steels, cast iron, sintered iron, tempered castings, non‑ferrous metals and hard plastics, and it performs reliably in workshop and industrial drilling applications. How does the short design affect drilling results with the MetavCUT Twist Drill? A short format per DIN 338 reduces the exposed length of the bit, increasing stiffness and lowering the risk of bending; this improves concentricity and hole accuracy on Drilling Machines and is particularly advantageous for precision tasks and drilling in hard materials. For what are Twist Drills used? Twist Drills are mainly applied when machining high‑strength materials and larger diameters; this form is easy to regrind and withstands higher loads, making it a common choice for demanding metalworking and production tasks. Which three drill types are there? The main categories are metal drill bits, wood drill bits and stone/concrete drill bits.
7.5mm HSS-G Twist Drill DIN 338 ,short, bright finished, Type N - MetavCUT
Twist Drill — short Type N HSS‑G drill, 7.5 mm, 135°, bright finished, DIN 338, MetavCUT The Twist Drill is a short Type N HSS‑G drill designed for precise metal drilling in workshop and industrial applications, offering enhanced stability and a 135° point angle for hard materials. Short design for increased stability and precision High‑quality HSS‑G material for durable cutting 135° point for improved entry in hard metals Fully ground shank for precise concentricity Short design for stable, precise metal drilling A shorter overall length reduces overhang and significantly increases stability during drilling, which directly improves hole accuracy. The short execution means less vibration and a lower risk of bending when used in hand or machine drilling setups. This characteristic is particularly advantageous when working with hard or alloyed steels, where deflection would otherwise compromise the hole quality. High‑performance material and geometry for tougher tasks Made from HSS‑G, the geometry of the flute and the CNC grinding process produce very sharp cutting edges and consistent geometry for clean, round holes. The 135° point angle reduces the tendency to wander when starting a hole and shortens the initial penetration time in harder materials. For users with limited metallurgical knowledge: the larger point angle flattens the tip and distributes cutting forces, which helps when drilling stainless steel and other difficult alloys. Where this drill delivers the best results Engineered as a Type N normal‑spiral twist drill, this tool excels at drilling metals such as alloyed and unalloyed steel, cast steel, cast iron, sintered iron, malleable iron, non‑ferrous metals and hard plastics. The bright finished surface improves chip evacuation in many workshop applications. Workshops and metalworking professionals benefit from the combination of short length and fully ground shank for repeatable concentricity in production and maintenance tasks. Practical use and care for longer service life Correct use with appropriate coolant and moderate feed rates extends life and reduces breakage risk, since ground HSS drills, while sharp, can be more brittle than rolled variants. A fully ground shank ensures secure clamping and minimal runout; users should verify chuck grip and use steady feed. Periodic resharpening restores cutting geometry; the ground flutes make controlled resharpening possible on a bench grinder or by service providers. For robust and precise metalworking rely on MetavCUT’s short Twist Drill — METAV Werkzeuge provides expert advice and personalised support via email info@metav-werkzeuge.com, phone +49 2822 7131930 or WhatsApp +49 170 2837271 Designation: Twist Drill Brand: MetavCUT SKU: 45075-FDA Diameter: 7.5 mm Point angle: 135° Type: Type N Execution: short Colour: bright finished Material: HSS‑G Shank execution: fully ground Spiral length: 69 mm Overall length: 109 mm Application: Drills for metal Standard: DIN 338 Suitable for: Drilling Machine Manufacturer: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What materials is the MetavCUT Twist Drill Type N best suited for? The Twist Drill by MetavCUT (Type N) is optimised for drilling metals including alloyed and unalloyed steel, cast steel, cast iron, sintered iron, malleable iron, non‑ferrous metals and hard plastics; its geometry and HSS‑G material favour performance on harder workpieces. How should the MetavCUT Twist Drill be used to avoid breakage? For the Twist Drill from MetavCUT, use steady feed, appropriate coolant and a secure chuck grip; since the drill is fully ground, it offers precision but benefits from controlled cutting conditions and occasional resharpening to maintain edge geometry. For what is a Twist Drill used? It is used primarily for machining high‑strength materials and large drill diameters; the form is easy to resharpen and withstands higher loads. Which three drill types exist? There are Metal drills, Wood drills, and Stone/Concrete drills. Why are twist drills point‑sharpened? Point‑sharpening reduces the cross‑cut at the tip, lowering friction and required feed forces while improving centring of the drill tip in the workpiece. Can a metal drill be used to drill wood? A metal drill can be used in wood but usually provides poorer guidance and less clean holes; however, such drills are easier to resharpen and have less self‑feeding tendency. At which drilling depths is the twist drill most commonly used? A through‑hole in solid material is often executed with a twist drill; for diameters up to 20 mm and drilling depths up to 100 mm, the twist drill is the most commonly used tool. Is HSS or HSSE better? The common belief that HSSE is universally superior to HSS is not always correct; choose according to actual working conditions to determine whether the higher cost of HSSE is justified.
7.5mm HSS-G Twist Drill DIN 338 ,short, bright finished, Type N - MetavCUT
Twist Drill – Type N, Ø 7.5 mm, 135° tip, Short, Bright Finished, HSS‑G, DIN 338 by MetavCUT The Twist Drill Type N is a short, high‑performance metalworking drill designed for precision drilling in steels and other hard materials with a 135° tip angle for reduced wander. Short design for increased Stability and Precision Ground HSS‑G for sharp cutting and clean holes 135° tip for hard Metals and reduced breakout Conforms to DIN 338 for consistent dimensions and quality Faster, more stable drilling for professional metalwork A short design reduces overhang and significantly improves stability during drilling, which means less runout and more accurate hole placement. The fully ground HSS‑G geometry creates very sharp cutting edges that produce cleaner holes and lower burr formation. For users working on Steel, Cast Iron or Tempered Components, this yields a measurable gain in workpiece quality and shorter rework times. Optimised geometry reduces effort and increases lifetime Thanks to the 135° tip angle, the drill enters hard materials with less deflection, shortening the initial penetration phase and improving centring. Combined with the Type N normal spiral, the design balances chip evacuation and cutting force so that Feed Forces are reduced. This lets operators drill up to 40% faster in many applications while requiring noticeably less pressure at the chuck. Built for exacting applications and machine use Conformity to DIN 338 guarantees standardised lengths and shank dimensions for secure clamping in the chuck of any compatible Drilling Machine. The fully ground flute profile (HSS‑G) delivers excellent roundness and is especially suited to stationary or powered machines where consistent accuracy is required. Use coolant for prolonged tool life and to avoid thermal softening when machining alloyed steels. Who benefits from this short Type N twist drill Designed for professional workshops, tool rooms and production environments, the drill is ideal for technicians who need repeatable precision in metal fabrication. The shorter Spiral Length minimises vibration and is particularly useful when drilling into thick or high‑strength components. For occasional users performing metal repairs, the robust grind also allows straightforward re‑sharpening when required. We recommend the MetavCUT short Type N Twist Drill for demanding metalworking tasks — for tailored advice or additional technical data contact METAV Werkzeuge: info@metav-werkzeuge.com · Phone +49 2822 7131930 · WhatsApp +49 170 2837271 Twist Drill Marke: MetavCUT SKU: 48075-FDA Diameter: 7.5 mm Tip Angle: 135° Type: Type N Overall Length: 109 mm Spiral Length: 69 mm Execution: short Shank Finish: fully ground Surface/Colour: bright finished Material: HSS-G Standard: DIN 338 Application: Drills for metal For Drilling Machine: Drilling Machine Manufacturer: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ For what is a Twist Drill used? A Twist Drill such as the MetavCUT Type N short drill is primarily used for machining high‑strength materials and for larger drill diameters. Its geometry is easy to re‑grind and it withstands higher mechanical loads, which makes it particularly suitable for steel and similar hard workpieces. Which three drill types exist? The three main categories are Metal Drills, Wood Drills and Stone/Concrete Drills, each optimised for the material to be machined and differing in tip geometry and flute design.
7.5mm HSS-G Twist Drill DIN 338 ,short, TIN-coated - MetavCUT
Spiralbohrer 7,5 mm von MetavCUT (kurze Ausführung) Der Spiralbohrer von MetavCUT in kurzer Ausführung für präzise Metallbohrungen an handgeführten und stationären Maschinen MetavCUT Spiralbohrer 7,5 mm geschliffen TIN-beschichtet für erhöhte Lebensdauer HSS-G geschliffen für hohe Präzision kurze Auskraglänge für verbesserte Stabilität Geeignet für Stahl, Guss und Nichteisenmetalle Präzise Ergebnisse durch kurze Bauform und scharfe Geometrie Die kürzere Ausführung kombiniert geringe Auskraglänge mit HSS-G-Werkstoff und einem präzisen CNC-Schliff, was die Stabilität beim Bohren deutlich verbessert. Durch die reduzierte Neigung zum Verbiegen lassen sich saubere, runde Bohrlöcher erzielen, auch bei handgeführten Anwendungen. Die geschliffene Ausführung liefert schärfere Schneiden und eine bessere Rundlaufgenauigkeit, was in vielen Werkstätten zu messbar schnellerem Vorschub und zuverlässigen Passungen führt. Beschichtung reduziert Reibung und verlängert Standzeit Die TIN-Beschichtung (Titan-Nitrid) mindert Reibung und erhöht die Oberflächenhärte, sodass sich die Lebensdauer des Werkzeugs beim Bohren von Metallen verlängert. In Kombination mit geeignetem Kühlschmierstoff sinken Verschleiß und Wärmeentwicklung; das Ergebnis sind konstant saubere Bohrbilder und weniger Werkzeugwechsel. Gerade bei Serien- oder wiederholten Bohrungen im Metall zahlt sich die Beschichtung durch geringere Stillstandszeiten aus. Breites Einsatzspektrum für verschiedene Metallwerkstoffe Der Bohrer eignet sich zur Bearbeitung von legiertem und unlegiertem Stahl, Temperguss, Gusseisen, Sintereisen sowie Nichteisenmetallen wie Neusilber, Kupfer und Bronze; auch Hartkunststoff ist bearbeitbar. Für Werkstätten bedeutet das eine hohe Flexibilität: Ein Werkzeug deckt viele Anwendungen ab, reduziert Rüstzeiten und vereinfacht die Lagerhaltung. Durch die kurze Ausführung profitieren Anwender von besserer Spindelstabilität und geringerer Vibration bei variierenden Werkstücken. Norm, Spitzengeometrie und sichere Anwendungsempfehlungen Die Ausführung entspricht DIN 338, womit die Abmessungen und Toleranzen für kurze Spiralbohrer mit Zylinderschaft definiert sind. Der Spitzenwinkel von 118° ist ausgewogen für allgemeine Metallbearbeitung und erleichtert das Zentrieren in Standardmaterialien. Für höchste Maßhaltigkeit empfiehlt sich vor allem bei präzisen Passungen das Anpunkten mit einem Zentrierbohrer. Kühlung und moderates Vorschubverhalten schützen Schneide und reduzieren Bruchrisiko, besonders bei geschliffenen Bohrern. Empfehlung: Für präzise und zuverlässige Metallbohrungen empfiehlt MetavCUT den Spiralbohrer mit kurzer Ausführung – technische Beratung und Verfügbarkeit direkt bei Metav anfragen per info@metav-werkzeuge.com oder telefonisch unter +49 2822 7131930 Produktmerkmale Artikelnummer: 28075-FDA Marke: MetavCUT Bezeichnung: Spiralbohrer Serie: Basic Line Einsatzgebiet: Bohrer für Metall Norm: DIN 338 Fakten Durchmesser: 7,5 mm Gesamtlänge: 109 mm Spirallänge: 69 mm Spitzenwinkel: 118° Verpackungseinheit: 10 Besonderheiten Material: HSS-G (Schnellarbeitsstahl, geschliffen) Oberfläche: TIN-beschichtet (Titan-Nitrid) Schaftausführung: geschliffen Ausführung: kurz Für Bohrmaschine: Handbohrmaschine FAQ Ist der Bohrer für Handbohrmaschinen geeignet? Ja. Der MetavCUT Spiralbohrer 7,5 mm (Basic Line, SKU 28075-FDA) ist für den Einsatz in Handbohrmaschinen vorgesehen; die kurze Ausführung verbessert dabei die Stabilität und reduziert Verkantungsrisiken im Vergleich zu langen Ausführungen. Für welche Materialien ist dieser Bohrer geeignet? Der Spiralbohrer von MetavCUT eignet sich für legierten und unlegierten Stahl, Temperguss, Gusseisen, Sintereisen sowie Nichteisenmetalle wie Kupfer, Bronze und Neusilber; auch Hartkunststoff kann bearbeitet werden. Welche Vorteile bringt die TIN-Beschichtung? Die TIN-Beschichtung am MetavCUT Spiralbohrer reduziert Reibung, senkt Wärmeentwicklung und erhöht die Standzeit; in Verbindung mit Kühlschmierstoff führt dies zu weniger Verschleiß und konstanteren Bohrergebnissen. Worin unterscheidet sich die geschliffene Schaftausführung? Geschliffene Bohrer (HSS-G) haben schärfere Kanten und höhere Rundlaufgenauigkeit als gewalzte Varianten. Der Nachteil ist eine erhöhte Bruchanfälligkeit bei unsachgemäßer Handhabung, daher empfiehlt sich die Nutzung mit Kühlung und kontrolliertem Vorschub. Brauche ich ein Vorbohren oder Zentrieren für präzise Bohrungen? Für besonders präzise Passungen empfiehlt sich das Anpunkten mit einem Zentrierbohrer; allgemein lässt sich der 7,5-mm-Bohrer direkt einsetzen, wobei Zentrierung die Maßhaltigkeit weiter verbessert.
7.5mm HSS-G Twist Drill DIN 338 ,short, TIN-coated, Type N - MetavCUT
Twist Drill — Short HSS‑G, 7.5 mm, 135° Tip, Type N, TiN‑coated (MetavCUT) A Twist Drill short Type N for Drilling Machines, designed for precision metalworking and high stability in hard materials. Short design for higher stability and accuracy TiN‑coating reduces friction and extends tool life HSS‑G fully ground for fast, clean metal drilling 135° tip optimized for hard and stainless steels Conforms to DIN 338 for consistent industrial quality Precision and stability from a short design The short design of this HSS‑G Twist Drill reduces the exposed length from the chuck, resulting in markedly higher stability and less deflection during operation. This makes the bit particularly suitable for precision tasks and for drilling in hard materials where accuracy matters. Reduced vibration leads to cleaner holes and less wear on both tool and machine, which benefits production workflows and workshop maintenance. Coating and material deliver longer life under load Equipped with a TiN‑coating, the cutter benefits from lower friction at the cutting edge, which decreases heat build‑up and abrasion when drilling metals. The base material HSS‑G (ground high speed steel) provides sharp geometry and high hardness. Combined, these features increase durability when working with alloyed and unalloyed steels, cast iron, copper, bronze and hard plastics, while recommended coolant use further extends service life. Geometry and norm for demanding metalwork With a 135° tip angle and Type N (normal spiral) geometry, the bit enters harder materials with reduced walking and improved centering, shortening approach time on tough workpieces. Manufacturing to DIN 338 ensures standardized dimensions and performance expectations for short twist drills with cylindrical shanks, so compatibility with industrial clamps and fixtures is assured. The fully ground flutes also enable up to ~40% faster penetration and lower required feed force compared with conventional HSS variants. Who benefits and how to use it best Metalworkers, toolrooms and industrial maintenance teams will appreciate the combination of short length, TiN surface and ground geometry for demanding tasks. For best results, secure the workpiece, use recommended spindle speeds for 7.5 mm HSS bits, and apply suitable cutting fluid to minimise wear. The short Twist Drill is ideal for stationary drilling machines but can also be used in hand drilling machines when stability is ensured. Strong recommendation: choose the MetavCUT Twist Drill for reliable, high‑precision metal drilling — and if you are unsure whether this tool matches your application or need further technical data, METAV Werkzeuge provides comprehensive expert advice: info@metav-werkzeuge.com • +49 2822 7131930 • WhatsApp +49 170 2837271 Technical Data Designation: Twist Drill (Short) Brand / Manufacturer: MetavCUT SKU: 46075-FDA Type: Type N Diameter: 7.5 mm Spiral length: 69 mm Total length: 109 mm Tip angle: 135° Material: HSS‑G Coating / Colour: TiN‑coated Shaft execution: Fully ground Execution: Short For machine: Drilling Machine (Hand Drilling Machine) Application: Drills for metal Norm: DIN 338 Model series: Standard Line Packaging unit: 10 Manufacturer: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ Is the MetavCUT Twist Drill suitable for stainless steel and other hard alloys? The MetavCUT Twist Drill (Type N) is designed for metalworking and, with its 135° tip and TiN coating, is well suited for alloyed and unalloyed steels as well as other hard metals; using coolant is recommended to maximise tool life. What does "fully ground" mean for the MetavCUT Twist Drill and why is it important? Fully ground (HSS‑G) indicates that the flute geometry is produced by CNC grinding rather than rolling, giving the MetavCUT Twist Drill very sharp edges, excellent run‑out accuracy and cleaner holes—advantages especially valuable when machining metalen components. What is a Twist Drill mainly used for? A Twist Drill by MetavCUT is primarily applied when machining high‑strength materials and larger diameters; its form is easy to regrind and remains robust under high loads. Which three drill types exist? The common categories are Metal drills, Wood drills and Stone/Concrete drills. Why are Twist Drills point‑sharpened? Point‑sharpening reduces the web thickness at the tip of the Twist Drill, which significantly lowers friction and the necessary feed forces while improving centring in the workpiece. Can a metal Twist Drill be used for wood? A metal (HSS) drill can be used in wood, but guidance and hole finish are generally inferior compared with dedicated wood drills; metal bits are easier to resharpen and have less self‑feeding tendency. For which drilling depths is the Twist Drill most commonly used? A through hole in solid material is typically made with a Twist Drill; for diameters up to about 20 mm and drilling depths up to 100 mm, the Twist Drill is the most frequently employed tool. Is HSS or HSSE better? The idea that HSSE is categorically superior to HSS is not universally true; decide based on actual working conditions and whether the performance justifies higher costs for HSSE materials.
7.5mm HSS-G Twist Drill DIN 338 ,short, TIN-coated, Type N - MetavCUT
Der kurze Spiralbohrer verbindet hohe Stabilität durch die kurze Ausführung mit einer TiN‑Beschichtung für reduzierte Reibung und längere Lebensdauer; ideal für das Bohren in Stahl. Bestellen Sie den Spiralbohrer direkt über Metav Werkzeuge oder fragen Sie unsere Beratung an. Spiralbohrer von MetavCUT, Profi Line (Kurzausführung) Der Spiralbohrer von MetavCUT ist ein kurzer, geschliffener HSS‑Bohrer für präzise Metallbearbeitung und stationäre sowie mobile Anwendungen. Spiralbohrer »Spiralbohrer« von MetavCUT HSS‑G geschliffen für hohe Präzision TiN‑Beschichtung für reduzierte Reibung 135° Spitzenwinkel für harte Werkstoffe Kurze Ausführung für maximale Stabilität Präzision und Materialvorteile für Metallbearbeitung Die geschliffene HSS‑G Ausführung sorgt für besonders scharfe Schneiden und eine hohe Rundlaufgenauigkeit, was saubere Bohrlöcher in Metall garantiert. Durch die TiN‑Beschichtung wird die Reibung reduziert und die Wärmeentwicklung verringert, wodurch sich die Standzeit erhöht. Dieser Bohrer ist somit eine wirtschaftliche Wahl für Arbeiten in legiertem und unlegiertem Stahl sowie in Gusseisen und Nichteisenmetallen. Effizienz und Anwendungsempfehlung für Werkstatt und Montage Dank der kurzen Auskraglänge bietet die Konstruktion eine deutlich verringerte Neigung zum Verbiegen, was schnellere und stabilere Bohrvorgänge ermöglicht. Der 135° Spitzenwinkel erleichtert das Anbohren härterer Werkstoffe und reduziert das Abheben beim Eindringen. Bei Arbeiten mit Handbohrmaschine oder stationärer Maschine empfiehlt sich die Verwendung passender Kühlschmierstoffe, um Abrieb und Wärme weiter zu minimieren. Einsatzspektrum und Zielgruppenorientierung Der Bohrer richtet sich an Handwerk, Industriemechanik und anspruchsvolle Werkstätten, die präzise Metallbohrungen benötigen. Durch die robuste Bauart und die geschliffene Fertigung eignet sich das Produkt besonders für Anwender, die eine hohe Wiederholgenauigkeit und saubere Bohrbilder erwarten. Die kurze Version ist besonders empfehlenswert, wenn Stabilität und Rundlauf im Vordergrund stehen. Herstellungsstandard und Normkonformität Die Fertigung gemäß DIN 338 klassifiziert diesen kurzen Spiralbohrer mit Zylinderschaft als Standard für Metallbearbeitung. Geschliffene HSS‑G Bohrer bieten eine präzisere Geometrie als gewalzte Varianten und sind in vielen Profi‑Anwendungen die bevorzugte Wahl, insbesondere bei stationärem Einsatz mit Kühlung. Empfehlung: MetavCUT Profi Line wählen für langlebige Präzision; bei Fragen zur Anwendung wenden Sie sich an Metav Werkzeuge per eMail info@metav-werkzeuge.com oder Telefon +49 2822 7131930 Produktmerkmale Bezeichnung: Spiralbohrer SKU: 41075-FDA Marke: MetavCUT Serie: Profi Line Norm: DIN 338 Fakten Durchmesser: 7,5 mm Gesamtlänge: 109 mm Spirallänge: 69 mm Spitzenwinkel: 135° Verpackungseinheit: 10 Besonderheiten Material: HSS-G (Schnellarbeitsstahl geschliffen) Farbe: TiN-beschichtet (Titan‑Nitrid Beschichtung reduziert Reibung) Ausführung: kurz Schaft Ausführung: geschliffen Typ: Typ N (Normalspirale) Für Bohrmaschine: Handbohrmaschine FAQ Was zeichnet den Spiralbohrer von MetavCUT aus? Der Spiralbohrer von MetavCUT aus der Profi Line kombiniert eine geschliffene HSS‑G Geometrie mit TiN‑Beschichtung, was für saubere Bohrbilder, hohe Rundlaufgenauigkeit und verlängerte Standzeiten sorgt. Für welche Materialien ist dieser Bohrer geeignet? Der Spiralbohrer eignet sich für legierten und unlegierten Stahl, Temperguss, Gusseisen, Sintereisen sowie Nichteisenmetalle wie Kupfer und Bronze und Hartkunststoff. Warum ist die kurze Ausführung vorteilhaft? Die kurze Auskraglänge reduziert Vibration und Verbiegen, erhöht die Stabilität bei der Bohrung und verbessert so Präzision und Wiederholgenauigkeit, insbesondere bei stationären oder halbstationären Anwendungen. Welche Rolle spielt der 135° Spitzenwinkel? Der 135° Spitzenwinkel des MetavCUT Bohrers erleichtert das Anbohren harter Werkstoffe und verringert das Ausbrechen beim Austritt, wodurch sich die Qualität der Bohrung in Stahl verbessert. Ist der Bohrer für Handgeführte Maschinen geeignet? Ja, der Spiralbohrer ist für die Verwendung mit Handbohrmaschine ausgelegt, die kurze Ausführung verbessert jedoch die Stabilität; bei sensiblen Feinbohrungen sind stationäre Maschinen vorzuziehen. Welche Pflege verlängert die Lebensdauer des Bohrers? Der Einsatz geeigneter Kühlschmierstoffe in Kombination mit der TiN‑Beschichtung reduziert Reibung und Verschleiß und sorgt für längere Standzeiten des MetavCUT Spiralbohrers.
7.5mm HSS-G Twist Drill DIN 338 - MetavCUT
MetavCUT Twist Drill (Twist Drill, HSS‑G, Ø 7.5 mm, 135°) The MetavCUT Twist Drill is a precision metalworking Twist Drill designed for fast, clean holes in alloyed and unalloyed steels and other hard materials HSS‑G Material for high wear resistance 135° Tip angle for harder workpieces Triangular shank for secure tool retention Complies with DIN 338 for short twist drills Faster, cleaner metal drilling with less effort The specially ground HSS‑G geometry achieves notably higher productivity: tests show up to 40% faster drilling with approximately 50% less feed force compared with conventional HSS drills. This efficiency translates into reduced operator fatigue and shorter cycle times on both stationary and portable equipment. The optimised cutting edge aids in stable cutting, resulting in smoother hole walls and fewer rework operations. Robust design for professional workflows Constructed to DIN 338 standards, the short-cylinder form ensures consistent concentricity and repeatable performance in production environments. The triangular shank guarantees secure engagement in chucks and quick-change adaptors, preventing slippage during high-torque applications. The combination of a precision W-style tip and the hardened HSS‑G substrate provides extended tool life and resistance to the micro-welding that commonly affects drilling in tougher alloys. Broad suitability across demanding materials Engineered primarily as a Drill for Metal, this twist drill is suitable for alloyed and unalloyed steel, cast steel and cast iron, sintered and tempered materials, non‑ferrous metals such as aluminium and brass, and hard plastics. For softer materials such as wood or very soft plastics, performance is acceptable but guidance on feed and speed should be adjusted. The 135° tip angle is particularly effective when working with stainless steels and other higher‑strength materials. Practical advantages and recommended use With a spiral length of 69 mm and an overall length of 109 mm, the geometry balances chip evacuation with rigidity for Ø 7.5 mm diameters. The reduced point angle lowers the tendency to "grab" on entry and improves centring on flat surfaces, so pre‑drilling or spot‑facing is often unnecessary for many production tasks. Use moderate cutting speeds, adequate coolant or lubrication for ferrous materials, and clamp the workpiece securely to exploit the drill’s full potential. Strong recommendation: Choose the MetavCUT high‑performance Twist Drill for faster, more precise metal holes — for technical advice or to confirm suitability for your application contact METAV Werkzeuge: 📧 info@metav-werkzeuge.com ☎️ +49 2822 7131930 ✔️ WhatsApp +49 170 2837271_ Designation: Twist Drill Brand: MetavCUT SKU: 55075-FDA Diameter: 7.5 mm Spiral Length: 69 mm Overall Length: 109 mm Material: HSS‑G Tip Angle: 135° Shaft Execution: with multi‑bevel cutting edge and triangular shank Model Series: Spezial Application: Drills for metal For Drilling Machine: Drilling Machine Standard: DIN 338 Manufacturer: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What is the MetavCUT Twist Drill used for? The MetavCUT Twist Drill (Twist Drill) is primarily applied to machining high‑strength materials and larger diameters; it is easy to resharpen and remains stable under greater loads, making it suitable for demanding metalworking tasks where clean, burr‑free holes are required. Which three drill types exist? The main categories are metal drills, wood drills and stone/concrete drills; the MetavCUT Twist Drill belongs to the metal drill family and is optimised for alloys, cast materials and hard plastics. Why are Twist Drills pointed? The pointing reduces the cross‑cut at the tip, which significantly lowers friction and therefore the required feed force; a sharpened tip helps centre the Twist Drill more reliably in the workpiece and reduces the tendency to wander on start.
7.5mm HSS-G Twist Drill DIN 340 ,long, bright finished - MetavCUT
Twist Drill — Long HSS‑G Twist Drill, Diameter 7.5 mm, Tip Angle 135°, Bright Finished, Fully Ground Shank, DIN 340 — MetavCUT Standard Line The Twist Drill is a long‑version HSS‑G drill designed for deep, accurate metal drilling with a 7.5 mm diameter and a 135° tip angle for harder materials. Long design for deep or hard-to-reach holes 7.5 mm Diameter for precise hole making 135° Tip Angle optimised for harder steels Fully ground HSS‑G for high precision and clean holes Efficient deep-hole drilling with less effort The Twist Drill in long execution delivers a clear advantage when deeper holes or recessed bores are required. The extended overall length (156 mm) and spiral length (102 mm) allow access to poorly reachable drilling positions without extensions. Thanks to the HSS‑G material and CNC‑ground flute geometry, the bit achieves reduced feed force and up to faster material removal compared with rolled counterparts, which increases productivity on metalworking tasks while maintaining precise hole quality. Geometry and material that improve performance on tough materials A 135° tip angle reduces initial cutting load and is particularly suitable for harder materials such as stainless and tempered steels. The fully ground shank and flute geometry produce very sharp cutting edges and excellent running accuracy, resulting in cleaner, more accurate holes. The drill complies with DIN 340 long‑version standards, making it a reliable choice for professional metalworking where repeatable precision matters. For non‑specialist users: HSS‑G means High Speed Steel, ground for superior sharpness and concentricity. Practical suitability and target applications This long HSS‑G twist drill is intended primarily for Drilling Machine use on metalwork: alloyed and unalloyed steel, cast materials (including grey and spheroidal graphite cast iron), sintered iron and non‑ferrous metals, as well as hard plastics. Its construction makes it ideal for workshop tasks requiring deep, through or blind holes up to moderate diameters. The bright finished surface improves chip evacuation and visibility when aligning holes, aiding consistent results in serial production or maintenance work. Usage tips for longevity and best results For best performance with the MetavCUT long twist drill, use appropriate cutting speeds, coolant and moderate feed to avoid undue stresses; ground drills can be more brittle than rolled types and benefit from controlled machining conditions. Centering and pilot holes improve hole quality in harder materials, while occasional resharpening restores geometry — an advantage of ground HSS bits is straightforward regrinding. Always secure the workpiece and use a suitable chuck for optimal concentricity. Strongly recommended: choose the MetavCUT Standard Line Twist Drill for demanding metalworking tasks — for expert advice, technical queries or to confirm suitability call METAV Werkzeuge at +49 2822 7131930, WhatsApp +49 170 2837271 or email info@metav-werkzeuge.com Bezeichnung: Twist Drill / Spiralbohrer Marke: MetavCUT SKU: 53075-FDA Durchmesser: 7.5 mm Spitzenwinkel: 135° Ausführung: long (lange Ausführung, DIN 340) Gesamtlänge: 156 mm Spirallänge: 102 mm Material: HSS‑G Schaftausführung: fully ground (geschliffen) Farbe: bright finished Anwendung: Drills for metal / Bohrer für Metall Für Bohrmaschine: Drilling Machine (Handbohrmaschine) Modellserie: Standard Line Norm: DIN 340 Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What materials can the MetavCUT Twist Drill reliably machine? The MetavCUT Twist Drill (long HSS‑G twist drill) is designed for metalworking and performs well in alloyed and unalloyed steel, cast steels, grey and spheroidal graphite cast iron, sintered iron, non‑ferrous metals and hard plastics; it is optimised for tougher materials thanks to the 135° tip. Is the MetavCUT Twist Drill suitable for deep holes and recessed bores? Yes, the long execution of the MetavCUT Twist Drill provides greater overall and spiral length for deep or hard‑to‑reach holes, making it well suited to through‑holes and blind bores where a standard‑length bit would be too short. What are twist drills used for? Twist Drills are primarily applied to the machining of high‑strength materials and for larger drill diameters. Their ground form allows easier regrinding and they withstand greater loads, making them suitable for deep holes or when access is restricted. Which three drill types exist? The three primary drill types are metal drills, wood drills and stone/concrete drills. Why are twist drills point‑sharpened? Point sharpening reduces the cross‑edge at the tip of the Twist Drill, which significantly lowers friction and required feed force while improving centring of the drill in the workpiece. Can a metal Twist Drill be used to drill wood? A metal (HSS) drill can be used in wood, but guidance and hole finish are inferior compared with dedicated wood drills. Metal drills are easier to resharpen and exhibit less aggressive self‑pulling. For which drilling depths is the Twist Drill most commonly used? Solid drilling is often performed with a Twist Drill. For diameters up to 20 mm and drilling depths up to 100 mm, the Twist Drill is the most commonly used tool. Which is better, HSS or HSSE? The general belief that HSSE is categorically superior to HSS is incorrect. When choosing, assess whether the working conditions justify the higher acquisition cost of HSSE for your specific application.
7.6mm HSS Twist Drill DIN 338 ,short, roll forged, black, Type N - MetavCUT
Twist Drill — Type N short HSS, 7.6 mm, 118° tip, black, DIN 338 (MetavCUT) The Twist Drill is a short Type N HSS twist drill for metal drilling, offering precise 7.6 mm holes with a 118° tip angle for use in hand drilling machines. Short HSS design for higher stability 7.6 mm diameter for precise metal holes 118° tip for reliable centring Complies with DIN 338 standard Suitable for hand drill applications Robust material for reliable metalworking results Hardened HSS (High Speed Steel) provides a balance of toughness and wear resistance that benefits everyday workshop and trade use. The short design reduces overhang and therefore vibration, which improves hole quality when working with metal. This combination makes the tool durable under typical loads and simplifies handling during repetitive tasks, so fewer rejects and cleaner holes are achieved with less reworking. Precision features that improve centring and control A 118° tip angle paired with the classic Type N spiral geometry promotes straightforward centring on most metals and eases entry into the workpiece. The shorter flute length increases stiffness and reduces deflection, giving better positional accuracy in handheld applications. For operators who prioritise precise alignment and repeatable hole locations, this configuration translates directly into faster set-up and less scrap. Designed for professional users and general workshop tasks This twist drill is optimised for machining operations on ferrous and non‑ferrous metals and is intended for use with a hand drill or compatible drilling machines. Craftspeople, maintenance technicians and small machine shops will benefit from the improved stability and the robust HSS material. The tool is particularly suitable where controlled, straight drilling is required and where frequent tool changes or resharpening are part of the workflow. Standards, sharpening and practical guidance Manufactured to DIN 338, the short format supports machining on both stationary and mobile drilling equipment. Regular sharpening of the point reduces the chisel edge width and lowers friction, which in turn diminishes necessary feed force and improves centring behaviour. When drilling harder alloys consider an adapted point geometry; for general metalworking the standard 118° offers a good compromise between cutting entry and centring performance. Secure precise metalworking results with the MetavCUT Twist Drill — contact METAV Werkzeuge for expert advice and purchasing support via email: info@metav-werkzeuge.com, phone: +49 2822 7131930 or WhatsApp: +49 170 2837271 Technical data Designation: Twist Drill Brand: MetavCUT SKU: 40076-FDA Diameter: 7.6 mm Spiral length: 69 mm Overall length: 117 mm Tip angle: 118° Execution: short Type: Type N Material: HSS Application: Drills for metal Colour: black Norm: DIN 338 For drill machine: Drilling Machine Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What is the MetavCUT Twist Drill used for? The MetavCUT Twist Drill is mainly used for machining high‑strength materials and larger bore diameters; its form allows straightforward resharpening and it withstands considerable loads, making it suitable for demanding metalworking tasks. Which three drill types exist? There are three common drill types: metal drill, wood drill and stone/concrete drill — the MetavCUT Twist Drill belongs to the metal drill category and is engineered accordingly. Why are twist drills sharpened? Sharpening reduces the chisel edge at the tip of the twist drill, which lowers friction and therefore the required feed force; this also improves centring of the MetavCUT Twist Drill in the workpiece and leads to cleaner drilling. Can a metal twist drill be used for wood? A metal drill such as the MetavCUT Twist Drill can be used in wood, but guidance and finish are usually inferior to purpose‑made wood bits; metal drills are easier to resharpen and have less self‑feed compared with specialised wood drills.
7.6mm HSS-E Twist Drill DIN 338 ,short, 5% cobalt-alloyed, Type N - MetavCUT
Twist Drill — Type N short, 7.6 mm, 135° point, HSS‑E, 5% cobalt‑alloyed (MetavCUT) The Twist Drill Type N short is a precision metal drilling bit designed for drilling machines and handheld drills, optimised for hard materials and stable, accurate holemaking. Short design for greater stability 135° point for hard materials HSS‑E with 5% cobalt for higher toughness Fully ground shank for precise runout Conforms to DIN 338 for metal drilling High stability and cutting performance for demanding metal work The short design of this Twist Drill reduces overhang and significantly improves stability during drilling, which minimizes bending and runout. Combined with the HSS‑E substrate and 5% cobalt alloying, the bit shows increased resistance to heat and wear when cutting steels and other tough metals. The 135° point angle is engineered to reduce chipping when penetrating hard materials and to slow the initial centring time, leading to cleaner entry holes and less workpiece deformation. Precision geometry and control for reliable results A fully ground shank and CNC-ground flute geometry ensure excellent concentricity and a smooth chip evacuation pattern; this results in a consistent hole diameter and better surface finish. The tool’s spiral length of 75 mm and overall length of 117 mm are balanced for use in both drilling machines and controlled handheld applications, offering a good compromise between accessibility and rigidity. For best results, use appropriate cutting speeds, steady feed and coolant when machining stainless steels or other hard alloys. Designed for professionals and demanding applications This Twist Drill in the Standard Line by MetavCUT is aimed at metalworkers, maintenance engineers and toolroom technicians who require a robust, repeatable solution for drilling into alloyed and unalloyed steels, cast iron and non‑ferrous metals. The Type N normal spiral design is the proven classic for metal drilling and provides a dependable choice where straightforward, high‑quality holes are needed. The shorter flute length makes it particularly suitable for precision tasks and confined setups. Care, handling and compatibility guidance To prolong tool life and maintain hole quality, clamp workpieces securely, select speeds appropriate to HSS‑E drills and apply cutting fluid for heat management. The short Twist Drill performs best with reduced overhang and minimal lateral force; avoid aggressive side loads to prevent premature fracture. If machining very hard alloys, progressively reduce speed and increase cooling to maintain cutting-edge integrity. The designation DIN 338 indicates this bit conforms to recognised standards for short twist drills with cylindrical shank. For precision metal drilling tasks choose the MetavCUT Twist Drill Type N short with 5% cobalt‑alloyed HSS‑E — for personalised advice or technical clarification METAV Werkzeuge offers expert consultation: 📧 info@metav-werkzeuge.com · ☎️ +49 2822 7131930 · ✔️ WhatsApp +49 170 2837271 Technical Data Bezeichnung: Twist Drill (Spiralbohrer) Marke: MetavCUT SKU: 47076-FDA Typ: Type N Durchmesser: 7.6 mm Spiral Length: 75 mm Gesamtlänge: 117 mm Spitzenwinkel: 135° Ausführung: short (kurz) Schaft Ausführung: fully ground (geschliffen) Material: HSS‑E Farbe: 5% cobalt‑alloyed Anwendung: Drills for metal (Bohrer für Metall) Norm: DIN 338 Modellserie: Standard Line Für Bohrmaschine: Drilling Machine (Handbohrmaschine) Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What materials is the MetavCUT Twist Drill Type N suitable for? The MetavCUT Twist Drill Type N with HSS‑E and 5% cobalt is primarily intended for drilling alloyed and unalloyed steel, cast iron and non‑ferrous metals; it performs well where heat resistance and edge retention are required. Can this Twist Drill be used in handheld drills? The short construction of the MetavCUT Twist Drill Type N improves stability and makes it suitable for careful use in handheld drills, though best results are achieved in a drilling machine or with firm workpiece clamping and controlled feed rates. For what is a Twist Drill used? A Twist Drill is mainly applied when machining high‑strength materials and larger drill diameters. Its geometry is easy to re‑grind and it withstands high loads, making it suitable for robust metalworking tasks. Which three drill types exist? The three main drill types are metal drills, wood drills and stone/concrete drills. Why are Twist Drills pointed? Pointing reduces the cross‑cutting edge at the tip of the Twist Drill. By pointing, friction forces are significantly lowered so that less feed force is required, while the tip centres better in the workpiece. Can you drill wood with a Twist Drill? A metal drill can also be used in wood, but guidance and surface finish are inferior; however, such drills are easier to re‑grind and typically exhibit lower self‑feeding tendencies. For which drilling depths is the Twist Drill most used? A through‑hole in solid material is commonly made with a Twist Drill. For diameters up to 20 mm and depths up to 100 mm, the Twist Drill is the most frequently used tool.
7.6mm HSS-G Twist Drill DIN 338 ,short, bright finished, Type N - MetavCUT
Nutzen Sie die Kombination aus kurzer Ausführung für höhere Stabilität, geschliffenem HSS‑G und dem 135° Spitzenwinkel für präzise Metallbohrungen; bestellen Sie den Spiralbohrer direkt über Metav oder fragen Sie unsere Beratung bei Bedarf an. Spiralbohrer »MetavCUT Standard Line« 7,6 mm Der Spiralbohrer kurze Ausführung aus HSS‑G, geschliffen und DIN 338-konform, für präzise Metallbohrungen an Handbohrmaschine und stationären Maschinen. Spiralbohrer MetavCUT »Standard Line« Kurze Ausführung für höhere Stabilität Geschliffen HSS-G für scharfe Kanten Spitzenwinkel 135°: Für harte Werkstoffe Zylinderschaft nach DIN 338, SKU 45076-FDA Höhere Stabilität und schnellere Vorschübe durch kurze Ausführung Die kurze Ausführung reduziert die Auskraglänge und verbessert somit die Stabilität beim Bohren, was Vibrationen und Abweichungen minimiert. Der geschliffene HSS‑G-Schliff sorgt für sehr scharfe Schneidkanten, saubere Bohrlöcher und eine hohe Rundlaufgenauigkeit. Herstellerangaben zufolge ist ein geschliffener HSS‑Bohrer bis zu 40 % schneller und benötigt 50 % weniger Anpresskraft im Vergleich zu herkömmlichen HSS‑Ausführungen, wodurch Arbeitszyklen effizienter gestaltet werden können. Geeignetes Einsatzfeld und Materialkompatibilität für verlässliche Ergebnisse Dieser Spiralbohrer ist primär für Metall ausgelegt und eignet sich besonders für legierte und unlegierte Stähle, Gussstahl, Gusseisen, Sintereisen, Temperguss, Nichteisenmetalle sowie harte Kunststoffe. Der 135° Spitzenwinkel reduziert das Wandern beim Anbohren in harten Werkstoffen und verbessert das Eindringverhalten. Für präzise Ergebnisse empfiehlt sich vor dem Bohren ein Anpunkten, um die Bohrstelle zu zentrieren und ein sauberes Startloch zu gewährleisten. Für welche Anwender die Ausführung entwickelt wurde Die Ausführung richtet sich an Werkstätten, Montagebetriebe und ambitionierte Heimwerker, die Wert auf präzise, reproduzierbare Bohrungen legen. Durch die Kombination aus Zylinderschaft nach DIN 338 und der robusten Konstruktion ist der Bohrer sowohl für Handgeführte Bohrmaschinen als auch für stationäre Maschinen geeignet. Die Standard‑Dimensionen und die einfache Handhabung machen dieses Werkzeug zur Alltagslösung in der Metallbearbeitung. Wartungshinweise und empfohlene Arbeitsweisen für lange Standzeiten Geschliffene Bohrer bringen sehr feine Schneiden, sind aber empfindlicher gegen Seitenbelastung; daher ist eine schonende Handhabung wichtig. Kühlung mit Schneidöl verlängert die Standzeit deutlich und reduziert thermische Belastungen beim Bohren in zähen Werkstoffen. Bei größeren Durchmessern oder tiefen Löchern empfiehlt sich ein abgestuftes Aufbohren und regelmäßiges Spanfreimachen, um Verstopfungen in der Spirale zu vermeiden. MetavCUT empfiehlt diesen Spiralbohrer der Standard Line für anspruchsvolle Metallbearbeitung – bei technischen Rückfragen steht Metav persönlich zur Verfügung: info@metav-werkzeuge.com | +49 2822 7131930 Produktmerkmale Artikelnummer: 45076-FDA Marke: MetavCUT Bezeichnung: Spiralbohrer Serie: Standard Line Ausführung: kurz Norm: DIN 338 Fakten Durchmesser: 7,6 mm Gesamtlänge: 109 mm Spirallänge: 69 mm Spitzenwinkel: 135° Verpackungseinheit: 10 Besonderheiten Material: HSS-G (geschliffen; hohe Schärfe) Schaftausführung: geschliffen (vollständig geschliffen) Typ: Typ N (Normalspirale für Metall) Farbe: blank Für Bohrmaschine: Handbohrmaschine FAQ Ist der Spiralbohrer MetavCUT Standard Line für Edelstahl geeignet? Der Spiralbohrer MetavCUT Standard Line (HSS‑G, SKU 45076-FDA) mit 135° Spitzenwinkel eignet sich für härtere Werkstoffe wie Edelstahl, wobei langsame Schnittgeschwindigkeiten und Kühlung empfohlen werden. Kann der Bohrer in einer Handbohrmaschine verwendet werden? Ja, der Spiralbohrer von MetavCUT ist für den Einsatz an Handbohrmaschine und stationären Maschinen ausgelegt; bei Handbetrieb auf eine sichere Spannaufnahme und moderaten Anpressdruck achten. Wie unterscheidet sich die geschliffene Ausführung vom rollgewalzten Bohrer? Geschliffen (HSS‑G) bedeutet CNC‑Schliff der Geometrie für schärfere Kanten und bessere Rundlaufgenauigkeit; der Spiralbohrer MetavCUT Standard Line liefert dadurch präzisere Bohrbilder, ist jedoch empfindlicher gegen seitliche Belastung. Welche Vorsichtsmaßnahmen verlängern die Lebensdauer des Bohrers? Für den Spiralbohrer MetavCUT Standard Line empfiehlt sich Kühlung mit Schneidöl, Anpunkten vor dem Bohren und regelmäßiges Spanmanagement, um Überhitzung und Bruch zu vermeiden. Für welche Anwendungen ist der 7,6 mm Durchmesser besonders geeignet? Der 7,6 mm Spiralbohrer der MetavCUT Standard Line eignet sich für allgemeine Werkstattarbeiten, Montageaufgaben und präzise Metallbohrungen in mittelstarken Blechen und Bauteilen.
7.6mm HSS-G Twist Drill DIN 338 ,short, bright finished, Type N - MetavCUT
Twist Drill Type N – MetavCUT short HSS‑G, 7.6 mm, 135°, Bright Finished, DIN 338 The Twist Drill Type N is a short HSS‑G metal drill designed for precision work on drilling machines with a 7.6 mm diameter and a 135° point angle. Short design for high stability and reduced bending 135° point angle ideal for hard materials like stainless steel Fully ground shank for superior runout accuracy Conforms to DIN 338 for short HSS twist drills Bright finished for clear visual inspection of cutting edges Outstanding Precision and Reduced Deflection The short construction of this MetavCUT drill delivers higher stability and significantly less tendency to bend compared with longer variants. Because the exposed length beyond the chuck is reduced, the tool remains more rigid under load, which produces more accurate holes and reduces the need for rework. This compact geometry is especially advantageous when drilling into hard or tough materials where tool deflection would otherwise compromise hole quality. Material and Standard: Built for Metalworking Reliability Manufactured from HSS‑G (ground high speed steel) and produced to DIN 338, this twist drill combines sharp cutting geometry with strict dimensional tolerances. The designation HSS‑G indicates CNC grinding of the flutes, resulting in very sharp cutting edges and excellent concentricity. The Type N normal spiral profile is the classic metalworking geometry, making this drill suitable for a wide range of ferrous and non‑ferrous metals while ensuring predictable performance in workshop and industrial environments. Optimised Cutting Geometry for Hard Materials With a 135° point angle, the drill penetrates harder materials more effectively and reduces the tendency to wander at the start of the cut. This angle shortens the initial bite into the material, offering better centring and lower feed effort for materials such as alloyed and unalloyed steel, cast steels and hard plastics. The combination of point geometry and a ground flute profile also helps produce cleaner chips and improved surface finish in the drilled hole. Performance, Handling and Machine Compatibility The tool features a spiral length of 75 mm and an overall length of 117 mm paired with a fully ground shank, which improves chucking accuracy and reduces runout. Compared with conventional HSS designs, this ground HSS version can enable up to 40% faster drilling with around 50% less feed force, provided appropriate speeds and cutting fluids are used. It is intended primarily for use on drilling machines rather than solely for handheld casual use, and benefits from steady clamping and, where necessary, coolant for longer tool life. We strongly recommend the MetavCUT short HSS‑G Twist Drill Type N for demanding metalworking tasks — for expert technical advice and to confirm suitability contact METAV Werkzeuge at info@metav-werkzeuge.com or call +49 2822 7131930, WhatsApp +49 170 2837271 Designation: Twist Drill (Spiralbohrer) Brand: MetavCUT SKU: 48076-FDA Type: Type N Diameter: 7.6 mm Point angle: 135° Execution: short Spiral length: 75 mm Overall length: 117 mm Shank finish: fully ground Surface finish: bright finished Material: HSS-G Standard: DIN 338 Intended for: Drilling Machine (Hand drill compatibility depends on clamping and setup) Application: Drills for metal Manufacturer: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ For what are Twist Drills used? Twist Drills such as the MetavCUT Twist Drill Type N are mainly used for machining high‑strength materials and larger drill diameters; their form is easy to grind and withstands higher loads, making them particularly suitable for metalworking where robust cutting performance is required. Which three drill types exist? The three common drill types are metal drills, wood drills and masonry/concrete drills; the MetavCUT Twist Drill Type N belongs to the metal drill category and is optimised for steel and similar materials.
7.75mm HSS Twist Drill DIN 338 ,short, roll forged, black, Type N - MetavCUT
Der HSS Spiralbohrer überzeugt durch HSS-Material und die kurze Ausführung nach DIN 338 für mehr Stabilität bei Metallbohrungen; nutzen Sie die Kombination aus Präzision und Robustheit für zuverlässige Werkstattarbeiten. Bestellen Sie den Bohrer bequem über Metav oder fragen Sie unsere Beratung bei Bedarf an. Spiralbohrer »400775-FDA« von MetavCUT (Typ N) Der Spiralbohrer »400775-FDA« ist ein kurzer HSS-Bohrer für präzise Metallbohrungen an stationären und handgeführten Maschinen Spiralbohrer »400775-FDA« von MetavCUT HSS-Material: Elastisch und bruchreduziert Kurze Ausführung nach DIN 338 für hohe Stabilität Spitzenwinkel 118° für leichtes Anbohren Geeignet für Handbohrmaschine und Metall HSS-Material für verlässliche Metallbearbeitung und längere Standzeit Hochwertiges HSS sorgt für eine gute Kombination aus Zähigkeit und Schneidhaltigkeit, wodurch Bruchrisiken reduziert und Verschleiß minimiert werden. Der Werkstoff ist geeignet für legierten und unlegierten Stahl, Gusseisen sowie Nichteisenmetalle und Kunststoff, sodass Anwender in Werkstatt und Montage auf konstante Leistung vertrauen können. Dieser Vorteil erhöht die Planungssicherheit bei wiederkehrenden Bohraufgaben. Kurze Bauform nach DIN 338 für präzisere Ergebnisse und höhere Stabilität Die kurze Ausführung gemäß DIN 338 reduziert die Auskragung und damit das Risiko von Verrundungen oder Abweichungen beim Bohren. In Verbindung mit der Typ‑N‑Spiralgeometrie eignet sich der Bohrer insbesondere für metallische Werkstücke, bei denen Maßhaltigkeit und gerader Bohrverlauf entscheidend sind. Für Anwender bedeutet das weniger Nacharbeit und sauberere Passungen. Optimale Einsatzgebiete: Alltagstauglich für Werkstatt und Montage Als Teil des Standardbereichs ist dieser Bohrer ideal für den Alltagsgebrauch in Werkstatt, Instandhaltung und bei DIY‑Projekten. Die Kombination aus Spitzenwinkel 118° und der robusten Konstruktion erlaubt sicheres Anbohren in dünnere bis mittlere Bleche und Profile. Nutzer profitieren von einfacher Handhabung an gängigen Handbohrmaschinen ohne aufwändige Vorbereitung. Technische Formgebung und Verpackung für effiziente Lagerung und Nutzung Die Abmessungen und die kurze Spiralform unterstützen eine gute Spanabfuhr bei typischen Metallarbeiten; die Lieferung erfolgt in handlichen Verpackungseinheiten, die Lagerung und Einsatzplanung vereinfachen. Der Bohrer ist als normalspiraliger Metallbohrer ausgeführt und bietet eine zuverlässige Lösung für Betriebe, die konsistente Bohrergebnisse erwarten. Greifen Sie zur MetavCUT HSS‑Lösung mit der SKU 400775‑FDA und sichern Sie sich präzise Bohrqualität; für Beratung und Lieferung erreichen Sie uns per E‑Mail info@metav-werkzeuge.com Produktmerkmale Artikelnummer: 400775-FDA Marke: MetavCUT Bezeichnung: Spiralbohrer Ausführung: kurz Daten Durchmesser: 7,75 mm Spirallänge: 75 mm Gesamtlänge: 117 mm Spitzenwinkel: 118° Verpackungseinheit: 10 Besonderheiten Material: HSS Norm: DIN 338 Für Bohrmaschine: Handbohrmaschine Typ: Typ N Farbe: schwarz FAQ Eignet sich der Bohrer für Edelstahl? Der Spiralbohrer von MetavCUT (Typ N, SKU 400775-FDA) ist primär für allgemeine Metallarbeiten ausgelegt; für hochlegierte oder gehärtete Edelstähle kann ein Bohrer mit größerem Spitzenwinkel oder spezieller Beschichtung sinnvoller sein. Kann der Bohrer in einer Akkubohrmaschine verwendet werden? Ja, der Spiralbohrer von MetavCUT (Typ N, SKU 400775-FDA) ist für Handbohrmaschinen und übliche Akkubohrschrauber im Standardbereich geeignet und liefert bei korrekter Ausrichtung stabile Ergebnisse. Wie wirkt sich der Spitzenwinkel 118° aus? Der Spitzenwinkel von 118° beim Spiralbohrer von MetavCUT (Typ N, SKU 400775-FDA) erleichtert das Anbohren und ist vorteilhaft bei weicheren bis mittelharten Metallen, da er gutes Zentrierverhalten bietet. Warum ist die kurze Ausführung nach DIN 338 wichtig? Die kurze Ausführung des Spiralbohrers von MetavCUT (Typ N, SKU 400775-FDA) reduziert Auskragung, erhöht Stabilität und führt zu geraderen Bohrungen, was insbesondere bei passgenauen Metallarbeiten Zeit spart. In welcher Menge wird der Bohrer geliefert? Der Spiralbohrer von MetavCUT (Typ N, SKU 400775-FDA) wird in Verpackungseinheiten zu 10 Stück geliefert, was sich für Werkstätten mit regelmäßigem Verbrauch praktisch einplanen lässt.
7.75mm HSS-G Twist Drill DIN 338 ,short, bright finished, Type N - MetavCUT
Twist Drill — short HSS-G Type N, 7.75 mm, 135°, bright finished The Twist Drill short Type N from MetavCUT is designed for precise metal drilling on Drilling Machines, offering a short overall length and a 135° point angle for demanding, hard materials. Short design for greater stability 7.75 mm Diameter for precise holes HSS-G ground geometry for clean metal drilling 135° Point angle for hard materials Precision and stability thanks to the short design A short construction reduces the free length outside the chuck, resulting in noticeably higher Stability and less deflection during machining. This makes the short Twist Drill particularly suited for precision work in steel and other hard materials, where a rigid tool setup produces cleaner holes and more consistent diameters. The DIN 338 classification guarantees that the geometry and dimensions meet recognised standards for short cylindrical-shank drills, so users can rely on repeatable results when machining alloys, cast materials or sintered iron. Ground geometry for sharper cutting and dimensional accuracy The designation HSS-G indicates a ground flute geometry produced by CNC grinding rather than rolling. This manufacturing method yields very sharp cutting edges and excellent Roundness of the hole, which benefits finishing operations and reduces the need for rework. While ground drills often show higher brittleness than rolled types, correct use with cutting fluid and machine support minimises the risk of breakage and extends tool life. For operators, the result is faster penetration and cleaner hole walls in materials such as alloyed and unalloyed steel. Target users and typical applications Metalworkers, toolshops and industrial maintenance teams will appreciate that this short Type N Twist Drill was developed for conventional and CNC Drilling Machines to machine metals reliably. The tool is intended for holes in Metal, including cast and tempered materials, and is less suitable for soft, fibrous materials where specialised point geometries perform better. MetavCUT focuses this product at professionals seeking a robust, repeatable drilling solution for workshops and production environments. Handling tips: angle, feed and cooling for best results A 135° point angle improves centring and reduces the initial bite when penetrating hard surfaces such as stainless steel, shortening the dwell time at drill start. Operators should use moderate spindle speeds and sufficient cutting fluid for cooling and chip evacuation, especially at larger diameters. The Fully Ground shank ensures good concentricity in the chuck, while proper clamping and minimal overhang will further reduce runout and deliver precise, burr-reduced holes. Strong recommendation: Choose the MetavCUT Twist Drill short Type N for demanding metalworking tasks — for personalised technical advice or to confirm suitability for your application, contact METAV Werkzeuge; Email: info@metav-werkzeuge.com — Phone: +49 2822 7131930 — WhatsApp: +49 170 2837271 Technical information Twist Drill Brand: MetavCUT SKU: 450775-FDA Diameter: 7.75 mm Spiral length: 75 mm Overall length: 117 mm Point angle: 135° Type: Type N Material: HSS-G Shank finish: Fully ground Execution: short Colour / Finish: bright finished For Drilling Machine Application: Drills for metal Model series: Standard Line Norm: DIN 338 Manufacturer: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ How well does the MetavCUT Twist Drill Type N perform in stainless steel? The MetavCUT Twist Drill short Type N is designed for hard materials; its 135° point angle and HSS-G ground geometry improve centring and cut quality in stainless steel when used with adequate cutting fluid and correct speeds. Can the MetavCUT Twist Drill be resharpened and reused? The HSS-G ground Twist Drill from MetavCUT can be resharpened on appropriate grinding equipment; careful resharpening preserves geometry, but frequent restoration may reduce core strength, so professional resharpening is recommended. What is a Twist Drill used for? A Twist Drill is mainly applied to the machining of high-strength materials and larger drill diameters; its shape is relatively easy to grind and can withstand higher loads, making it suitable for demanding metalworking tasks. Which 3 drill types are there? There are three common drill categories: Metal drill, Wood drill, and Stone / Concrete drill.
7.7mm HSS Twist Drill DIN 338 ,short, roll forged, black, Type N - MetavCUT
Twist Drill — Type N, HSS short, 7.7 mm, 118°, black, DIN 338 The Twist Drill Type N is a short HSS metal drill designed for precise drilling in steel and non-ferrous metals, suitable for hand drills and stationary drilling machines. Short HSS design for higher stability 7.7 mm diameter for precise metal holes 118° point angle for improved centering Conforms to DIN 338 for consistent quality Suitable for hand drills and drilling machines Stability and precision for metalworking Short-design HSS drill bits offer noticeably reduced flex during cutting, which increases precision when working with metals. The compact geometry of this short Twist Drill reduces overhang from the chuck and therefore minimises vibration and run-out. With a 7.7 mm diameter and the Type N normal spiral, the tool provides a reliable geometry for producing clean, cylindric holes in alloyed and unalloyed steel. Conformity to DIN 338 signals consistent manufacturing tolerances and repeatable results across batches. Material performance and application Understanding why HSS (High Speed Steel) is chosen helps assess suitability: HSS combines hardness and elasticity, allowing the drill to withstand heat and maintain cutting edges under standard metalworking conditions. This makes the short Twist Drill particularly effective for machining steel, cast iron, non-ferrous metals and certain plastics. The 118° point angle favours easier centring on curved or softer surfaces and reduces the required axial force compared with steeper angles, which improves handling during manual drilling. Who benefits from this tool Workshops and maintenance technicians who prioritise accuracy and tool life will value the design of this MetavCUT product. Operators using portable hand drills as well as production machines benefit from the shorter working length, which delivers enhanced stiffness and repeatability. For users who need a classic metal drill geometry, the Type N spiral is the established choice for general-purpose metal drilling, offering straightforward re-sharpening when required. Durability, handling and practical tips A short Twist Drill designed in HSS is easier to stabilise in the chuck and tends to produce better edge life under moderate cutting speeds. For best results, start with a light pilot and steady feed, and adjust coolant or cutting lubricant when drilling tougher alloys to extend service life. The point geometry supports quicker initial penetration, while the solid material composition allows controlled resharpening on standard grinding equipment, preserving the original cutting geometry and extending tool usability. Strong recommendation: For precise metal drilling choose the MetavCUT Twist Drill with HSS short design and 118° point angle — for expert advice or to confirm suitability for a specific task contact METAV Werkzeuge: 📧 info@metav-werkzeuge.com ☎️ +49 2822 7131930 ✔️ WhatsApp: +49 170 2837271 Designation: Twist Drill (short) Marke: MetavCUT SKU: 40077-FDA Typ: Type N Diameter: 7.7 mm Point angle: 118° Material: HSS Finish/Version: short Colour: black Spiral length: 75 mm Overall length: 117 mm Application: Drills for metal Suitable for: Hand drills and Drilling Machine Standard: DIN 338 Manufacturer: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What is the Twist Drill used for? The Twist Drill from MetavCUT is primarily applied to the machining of high-strength materials and for larger drilling diameters where robustness is required. This short HSS metal drill is easy to sharpen and resists higher loads, making it suitable for demanding metalworking tasks. Which three drill types are there? Common drill types are metal drills, wood drills and stone/concrete drills. The MetavCUT Twist Drill belongs to the metal drill category and is optimised for steel and other metallic materials. Why are Twist Drills sharpened at the tip? The tip grind reduces the chisel edge area at the drill point, significantly lowering friction and therefore the required feed force. For the MetavCUT Twist Drill, a sharpened tip also improves centring in the workpiece and reduces heat generation during cutting. Can a Twist Drill be used for wood drilling? A metal-purpose Twist Drill such as the MetavCUT variant can be used in wood, but guidance and finish are inferior compared with dedicated wood drills. Metal drills tend to have less accurate guidance and produce a less clean hole, although they are easier to resharpen and show reduced self-feeding.
7.7mm HSS-E Twist Drill DIN 338 ,short, 5% cobalt-alloyed, Type N - MetavCUT
MetavCUT Twist Drill – Type N short, 7.7 mm, HSS‑E, 135°, 5% cobalt‑alloyed, fully ground, DIN 338 The Twist Drill from MetavCUT is a short Type N drill designed for precision metalworking and optimized for drilling machines and hand drills. Short design for increased stability and precision 7.7 mm Diameter for accurate through‑holes 135° Point angle for hard materials like stainless steel Fully ground shank for high runout accuracy HSS‑E with 5% cobalt for enhanced wear resistance Precision and stability for demanding metalwork The short Twist Drill construction reduces the protruding length from the chuck, resulting in markedly improved Stability and less tendency to bend under load. This makes the tool particularly suitable for precise operations and for drilling in hard Metals where deflection would compromise hole quality. With a 135° Point Angle, the cutting action engages smoothly on tough surfaces, shortening dwell on entry and improving centring on stainless steel and alloyed steels. Material composition and durability benefits Manufactured from HSS‑E with 5% cobalt alloying, this short Type N drill offers improved Heat Resistance and edge life compared with standard HSS. The cobalt content supports higher cutting temperatures and helps maintain sharpness when machining alloyed or high‑strength Steels. The fully ground flute geometry provides very sharp cutting edges and high roundness, which delivers clean holes and consistent tool life under appropriate coolant and machine conditions. Designed for efficient workshop use By combining a short overall length with a roll‑free, fully ground shaft and compliance with DIN 338, the drill delivers reproducible hole quality on stationary and portable machines alike. The reduced overhang lowers vibration, enabling higher feed rates and improved surface finish for through‑holes. For routine metal drilling tasks the short HSS‑E Twist Drill allows operators to maintain productivity without sacrificing precision. Recommended applications and user guidance This Twist Drill is optimised for drilling in Alloyed and Unalloyed Steel, Cast Iron, Non‑Ferrous Metals and Plastics when high precision is required. For best results, use appropriate cutting fluid and secure workholding; short drills perform best in guided or rigid setups. If drilling in softer woods, be aware that metal drills can work but may show inferior guidance and finish compared with purpose wood drills. For holes up to moderate depths, the short geometry reduces breakage risk in small diameters and improves repeatability. Strong recommendation from MetavCUT: Choose this short HSS‑E Type N Twist Drill for stable, high‑precision metal drilling — for technical advice or application support contact METAV Werkzeuge: info@metav-werkzeuge.com, Tel +49 2822 7131930, WhatsApp +49 170 2837271 Technical information Designation: Twist Drill Marke: MetavCUT SKU: 47077-FDA Diameter: 7.7 mm Point Angle: 135° Type: Type N Execution: short Colour: 5% cobalt‑alloyed Material: HSS‑E Standard: DIN 338 Shank Finish: fully ground Overall Length: 117 mm Spiral Length: 75 mm For Drilling Machine: Drilling Machine / Hand Drill applications Application: Drills for metal Model Series: Standard Line Designation (EN): Twist Drill Manufacturer: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What is the MetavCUT Twist Drill Type N primarily used for? The MetavCUT Twist Drill Type N is primarily used for machining high‑strength and alloyed Metals; it excels in through‑holes for metalworking thanks to its short design and HSS‑E composition, which combined allow reliable drilling in demanding materials. Can the MetavCUT Twist Drill be used for wood? The MetavCUT Twist Drill (Type N) can be used in Wood, but as a Metal drill it offers less guidance and a rougher finish than a dedicated Wood drill; it is easier to re‑sharpen and shows less self‑pulling action compared with specialised wood bits. For what is a Twist Drill used? A Twist Drill is mainly applied to the machining of high‑strength workpieces and larger drill diameters; its shape allows straightforward re‑grinding and it withstands greater loads, making it suitable for drilling Metal and other tough materials. Which three drill types exist? The main drill categories are Metal drill, Wood drill and Stone/Concrete drill, and the MetavCUT Twist Drill belongs to the Metal drill group designed for steels and non‑ferrous Metals. Why are Twist Drills pointed? The point profile reduces the secondary cutting edge at the tip, lowering friction and thus decreasing required feed forces; this sharpening also improves centring accuracy when the MetavCUT Twist Drill is used in the workpiece. For which drilling depths is the Twist Drill most used? A solid bore is typically executed with a Twist Drill; for diameters up to about 20 mm and depths up to 100 mm, the Twist Drill is the most commonly used tool thanks to its versatile geometry and reliability. What is better, HSS or HSSE? The general assumption that HSSE steels are always superior to HSS is not correct; when deciding for the MetavCUT Twist Drill in HSS‑E, assess whether the working conditions justify the higher cost of HSSE, as performance gains depend on the specific application and material.
Why carbide indexable inserts remain the go-to choice
Carbide indexable inserts are the most widely used and versatile cutting inserts in machining. Manufactured from a sintered mixture of hard particles such as tungsten carbide and a metallic binder like cobalt, these inserts form the actual cutting edge on toolholders including milling cutters, turning inserts and drills. Synonyms used here: carbide cutting inserts, indexable carbide inserts.
How they perform under coolant and load
As the cutting element, carbide indexable inserts enable economic and precise machining across a broad spectrum of materials, from soft non‑ferrous metals to high‑strength steels. In tool systems without internal cooling, heat generated at the cutting zone is normally removed by external machine nozzles using coolant, which is adequate for most standard tasks, open contours and easily accessible components. For deep holes, heavy roughing or when working with materials that generate high temperatures such as stainless steel or titanium alloys, the use of internal cooling is essential: coolant is delivered through internal channels in the toolholder directly to the cutting edge under pressure to prevent thermal overload, optimise chip formation and extend insert life.
Key performance gains you can expect
- increased tool life through the high wear resistance and balanced toughness of tungsten carbide inserts
- consistent chip control and surface finish when coolant is delivered precisely via internal channels
- reduced machine downtime thanks to easy indexability and fast insert changes on compatible toolholders
- broad material compatibility, from soft non‑ferrous metals to hardened steels, enabling fewer tool variants in stock
- economic productivity by combining long stand life with repeatable cutting performance
Metav as your precision partner
Metav stands for the democratisation of precision. With decades of expertise and a catalogue that spans from high‑precision measuring instruments to full workshop equipment, Metav acts as a reliable quality filter for the European market from its Emmerich location. Over 48,000 customers trust Metav’s range and service; the breadth of more than 250,000 products helps reduce supplier complexity while ensuring consistent supply and product quality for industry and trade.
In brief: carbide indexable inserts at a glance
Carbide indexable inserts deliver the necessary balance of extreme wear resistance and mechanical toughness for versatile, cost‑efficient machining. Used with appropriate coolant strategy—external coolant for general work and internal cooling for demanding, deep or heat‑intensive operations—they are a cornerstone of modern metalcutting.
FAQ
What are carbide indexable inserts made of?
Carbide indexable inserts are manufactured from a sintered mixture of hard particles such as tungsten carbide and a metallic binder like cobalt, producing a cutting material that combines high wear resistance with the toughness needed to resist mechanical shock.
When is internal cooling necessary for carbide cutting inserts?
Internal cooling becomes necessary for deep hole drilling, heavy roughing and when machining materials that generate significant heat, such as stainless steel or titanium alloys. Internal cooling channels in the toolholder deliver coolant directly to the cutting edge to prevent thermal overload and improve chip breakage.
Can indexable carbide inserts be used without internal cooling?
Yes. For most standard applications, open contours and well‑accessible components, external coolant supplied by machine nozzles is sufficient, as tungsten carbide is more tolerant of moderate temperature fluctuations than some alternative materials.
How do carbide indexable inserts contribute to production efficiency?
By offering long tool life, stable cutting performance and quick indexability on compatible toolholders, indexable carbide inserts help reduce downtime, simplify tool inventories and maintain consistent part quality across varying materials.
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com