DCMT 11T302 ID5 Indexable Insert - ISCAR

Die Kombination aus Internal Coolant, passender Aufnahme für DCMT 11T3 Wendeplatten und kompakter Bauweise sorgt für zuverlässige Bearbeitung und einfachen Werkzeugwechsel. Nutzen Sie die präzise Spannfunktion und die robuste Konstruktion für stabile, linksgängige Drehbearbeitungen; bestellen Sie das Werkzeug direkt über Metav Werkzeuge oder fragen Sie unsere technische Beratung an. Clamping Holder SDJCL 1212 — SDJC for DCMT Indexable Inserts (Flat Version) The Clamping Holder SDJCL 1212 by Teknik Makina is designed for left-hand turning and secure use with DCMT 11T3 indexable inserts in precision turning applications Clamps DCMT 11T3 inserts securely Internal Coolant for improved chip evacuation Left-hand cutting orientation for specific turning tasks Compact 12 × 12 mm tool head for tight set-ups Torx Schraube M3,5×8,5 with Torx Schlüssel T15 Robust Design for Stable Clamping and Long Tool Life The Clamping Holder is built with a focus on secure retention and repeatable results. Its 12 mm Tool Head Width and Height keep the Insert seat compact, reducing overhang and vibration. The ISO designation SDJCL 1212 indicates the standardised form factor, simplifying integration into existing toolholders. As a result, machining runs are more consistent and Tool Life is extended through improved stability. Optimised Cutting Performance for Left-hand Turning Designed specifically for Left-hand cut direction, the holder accommodates a 93° Cutting Angle and a 32 mm Cutting Height, enabling controlled engagement and reliable chip formation when using DCMT 11T3 Inserts. The internal geometry supports precise positioning of the cutting edge, which translates into better surface finish and predictable material removal rates — a clear efficiency argument for production-focused workshops. Simple Assembly and Practical Service Features Installation and maintenance are straightforward: the clamping uses a Torx Schraube M3,5×8,5 tightened with Torx Schlüssel T15, while the clamping plate TA030 is secured with an M5 locating screw. The presence of Internal Coolant channels improves cooling at the cutting zone and facilitates chip evacuation, which reduces thermal load on the Insert and can prolong service intervals. These practical details reduce downtime and simplify tool changes. Ready for Workshop Use and Technical Support Compatible with DCMT 11T3 Indexable Inserts and specified under SKU AP575TM, this SDJC flat Clamping Holder is suitable for metalworking shops that require a compact, left-hand solution for turning tasks. If there is any doubt about fitment or coolant routing, our technical team at Metav Werkzeuge provides advice and configuration support to ensure the holder meets the machining requirement. Choose the Teknik Makina Clamping Holder with Internal Coolant for dependable left-hand turning — request a specification check or order assistance from Metav Werkzeuge at info@metav-werkzeuge.com or call +49 2822 7131930 Product Features Article number: AP575TM Brand: Teknik Makina Description: Clamping Holder SDJCL 1212 — SDJC for DCMT Indexable Inserts Facts Tool Head Width: 12 mm Tool Head Height: 12 mm Cutting Height: 32 mm Overall Height: 12 mm Overall Length: 110 mm Cutting Angle: 93° Weight: 0.11 kg Specials Innenkühlung: Yes — Internal Coolant channel for directed coolant flow Suitable for: DCMT 11T3 indexable inserts Cutting Direction: Left Clamping Plate: TA030 Torx Schraube: M3,5×8,5 Torx Schlüssel: T15 Bohrstange reference: J11-F-IC FAQ What inserts fit this clamping holder? The Clamping Holder SDJCL 1212 is specified for DCMT 11T3 indexable inserts and was engineered to secure that plate form reliably during left-hand turning operations. Does the holder support coolant-through functionality? Yes, the SDJC holder includes Internal Coolant channels that route coolant to the cutting zone to aid chip removal and reduce thermal stress on the Insert. Which fasteners are required for assembly? Assembly uses the supplied Torx Schraube M3,5×8,5, tightened with a Torx Schlüssel T15; the clamping plate is the TA030, with an M5 locating screw for fixture. Is this holder suitable for compact set-ups? With a Tool Head dimension of 12 × 12 mm and an overall length of 110 mm, the AP575TM holder is well suited to tight installations where minimising overhang is important. How can I get technical advice or confirm compatibility? Metav Werkzeuge provides technical consultation and can verify fitment for your application; contact info@metav-werkzeuge.com or call +49 2822 7131930 for assistance. Hersteller: Teknik Makina, Nolu Sokak, No 9, Selcuklu, Türkei, eMail: info@teknik-makina.com / Verantwortlich: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Characteristics: Order Number: AP572TM Item: Turning Holder usable with DCMT 11T3 Indexable Inserts Brand: Teknik Makina ISO Code: SDJCR 1616 H11-F-IC Quantitative Characteristics: Weight: 0.17kg Total length: 100mm Total Height: 16mm Cutting Height: 32mm Additional Informattion Cutting Direction: rechts Cooling Manufacturer Teknik Makina, Nolu Sokak, No 9, Selcuklu, Turkey, eMail: info@teknik-makina.com Responsible for Europe Metav Werkzeuge GmbH, Parkring 45, 46446 Emmerich, Germany, eMail: info@metav-werkzeuge.com

SDJC Clamp Holder for DCMT Indexable Inserts (AP571TM) The SDJC Clamp Holder secures DCMT Indexable Inserts in right-hand turning operations, offering a low‑profile flat design for stable, repeatable machining. Flat Design for low‑profile setups Compatible with DCMT 11T3 inserts Internal cooling for improved tool life ISO SDJCR 1212 designation for standard fits Torx screw M3.5x8.5 with T15 key for quick service Secure, repeatable clamping that saves setup time The SDJC Clamp Holder combines a compact footprint with a precise clamping geometry to deliver consistent tool positioning. The Flat Design and 12 mm Body Dimensions narrow the Contact Point between Holder and Insert, reducing run‑out and making repetitive setups faster. With the ISO designation SDJCR 1212 the Holder matches common Tooling Standards, so changeovers are straightforward and reliable for production workflows. Internal cooling and service‑friendly assembly Built‑in Internal Cooling channels support directed coolant flow close to the cutting edge, which helps control temperatures and extend Insert Life during continuous cutting. Service tasks are simplified by a single Torx Screw: use the Torx screw M3.5x8.5 together with a T15 Torx Key for secure clamping and quick replacement of Wendeplatten. The combination of cooling and easy service reduces downtime and keeps cycle times predictable. Precision fit for versatile workshop use Designed for right‑hand Cutting with a 93° Cutting Angle, the Holder suits a wide range of turning tasks where a low profile and stable tip position are essential. Compatibility with DCMT 11T3 Indexable Inserts ensures access to a broad selection of carbide grades and geometries, while the J11‑F‑IC Shank Design integrates with standard Toolposts. The overall length of 110 mm and a Cutting Height of 32 mm allow the Holder to be used in compact setups without sacrificing stability. Choose Teknik Makina’s SDJC Clamp Holder for dependable clamping — available via Metav Werkzeuge with technical advice and supply from Emmerich: info@metav-werkzeuge.com Product Features Article number: AP571TM Brand: Teknik Makina Designation: SDJC for DCMT Indexable Inserts Facts Width: 12 mm Height: 12 mm Cutting head width: 12 mm Cutting Height: 32 mm Overall Length: 110 mm Cutting Angle: 93° Cutting Direction: right Features Internal Cooling: Yes Suitable for Inserts: DCMT 11T3 (indexable carbide insert) Clamping Screw: M3.5x8.5 (Torx screw) Torx Key: T15 (Torx key) ISO Designation: SDJCR 1212 Shank Designation: J11-F-IC FAQ What Inserts fit this holder? The SDJC Clamp Holder from Teknik Makina is specified for DCMT 11T3 Indexable Inserts; the design (ISO SDJCR 1212) ensures a secure fit for standard DCMT inserts and enables quick index changes during production. Does the holder support coolant supply? Yes. The holder features Internal Cooling, which directs coolant close to the cutting edge to improve chip evacuation and reduce thermal wear on the Insert. Which screw and tool are required for assembly? Assembly and clamping use a Torx screw M3.5x8.5 operated with a T15 Torx key, allowing fast, repeatable clamping without special tooling. Is the holder suitable for right‑hand turning only? The product is configured for right‑hand Cutting Direction and a 93° Cutting Angle; it is optimised for right‑hand turning applications as stated for AP571TM. Which shank will integrate with standard toolposts? The shank designation J11‑F‑IC matches conventional mounting arrangements, making the holder straightforward to fit on compatible Toolposts in workshop environments. Hersteller: Teknik Makina, Nolu Sokak, No 9, Selcuklu, Türkei, eMail: info@teknik-makina.com / Verantwortlich: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

AP514TM Klemmhalter — SDJC for DCMT Indexable Inserts The AP514TM Klemmhalter is a left‑hand SDJC Toolholder designed for precision turning with DCMT 11T3 Indexable Inserts, combining compact geometry and Internal Cooling for consistent metal removal. SDJCL 1212 format for reliable clamping Compatible with DCMT 11T3 indexable inserts Internal Cooling for stable Chip Evacuation Left‑hand cutting, 93° Cutting Angle Compact head: 16 mm Cutter Width for tight spaces Built for dependable, repeatable machining results The Holder’s SDJCL 1212 geometry delivers a secure Clamp that minimises Insert movement under load, translating into consistent Dimensional Accuracy and surface finish. With a Cutting Angle of 93° and a Cutter Head Width of 16 mm, the tool is optimised for constrained set‑ups where accessibility and rigidity matter. The overall Length of 110 mm provides a balanced reach without excessive overhang, reducing Vibrations and supporting stable cutting conditions. Internal cooling that stabilises cutting performance This Toolholder features Internal Cooling, a routed coolant channel that directs fluid close to the cutting edge to improve Chip Evacuation and thermal control. The cooling path reduces edge wear and helps maintain cutting parameters for longer tool life, especially under continuous or demanding cycles. Fixing is achieved via a Torx Screw (M3,5x11) tightened with the Torx Key T15, offering reproducible clamp force and simple serviceability. Fast set‑up and broad compatibility with DCMT inserts Fitting is straightforward: the AP514TM accepts DCMT 11T3 style Indexable Inserts and uses U Plate TA030 with U Plate Screw M5 for secure mounting. The Holder’s designation (SDJCL 1212) corresponds to a 12 × 12 Shank Profile and a Cutting Height of 32 mm, enabling quick interchange on appropriate toolposts. The included Bohrstange designation J11‑IC matches common shank interfaces, so integration into existing tool inventories is efficient and predictable. Practical advantages for workshops and specialised operations Choose this Holder when process reliability and ease of maintenance are priorities. The combination of rigid Clamp geometry, targeted Internal Cooling and standardised fasteners reduces downtime for Insert changes and coolant maintenance. The left‑hand orientation suits applications where reverse cutting direction is required. Backed by Teknik Makina engineering, the AP514TM gives a straightforward route to improved cycle times and more consistent part quality. For reliable left‑hand SDJC performance choose the Teknik Makina AP514TM Klemmhalter — contact Metav Werkzeuge for tailored technical advice at info@metav-werkzeuge.com or by phone on +49 2822 7131930 Product Features Article number: AP514TM Manufacturer: Teknik Makina Designation: SDJC for DCMT Indexable Inserts ISO designation: SDJCL 1212 Facts Holder Width: 12 mm Holder Height: 12 mm Cutter Head Width: 16 mm Cutting Height: 32 mm Overall Height: 12 mm Overall Length: 110 mm Cutting Angle: 93° Weight: 0.11 kg Features Internal Cooling: coolant channel to the cutting zone Compatible Inserts: DCMT 11T3 (Indexable Insert format) U Plate: TA030 U Plate Screw: M5 Torx Screw: M3,5x11 Torx Key: T15 Shank / Bar: J11-IC FAQ What Inserts fit this Holder? The AP514TM Klemmhalter is designed for DCMT 11T3 Indexable Inserts; Teknik Makina’s SDJC geometry secures the Insert reliably for turning tasks. Does the Holder support coolant through the shank? Yes — the AP514TM features Internal Cooling, which channels coolant to the cutting edge to aid Chip Evacuation and thermal stability during longer cycles. Which fasteners are used to secure the Insert? Insert clamping is achieved with a Torx Screw (M3,5x11) tightened using a T15 Torx Key; this configuration ensures reproducible clamping torque for the AP514TM Klemmhalter. Is the Holder suitable for left‑hand operations? The AP514TM is a left‑hand SDJC Toolholder with a left‑oriented Cutting Direction and a 93° Cutting Angle, making it suitable where reverse turning is required. Can this Holder be mounted on standard turning bars? The Holder references the Bohrstange designation J11‑IC and uses U Plate TA030, streamlining integration with compatible tool posts and turning bars. Hersteller: Teknik Makina, Nolu Sokak, No 9, Selcuklu, Türkei, eMail: info@teknik-makina.com / Verantwortlich: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Combine Internal Coolant and secure Clamping with a compact profile to ensure consistent Right-hand Turning performance; benefit from the holder’s precise Cutting Height and compatibility with DCMT 11T3 inserts. Order or request technical advice from Metav Werkzeuge for confident integration into your Workshop. AP509TM Clamping Holder — SDJC for DCMT Indexable Inserts The AP509TM Clamping Holder is a right-hand SDJC Tool designed for turning with DCMT 11T3 Indexable Inserts, offering Internal Coolant and compact, robust dimensions. AP509TM Clamping Holder SDJCR 1212 Internal Coolant for Efficient Chip Evacuation Right-hand Cutting Direction for Turning Tasks 12 mm Holder Width and 12 mm Height Suitable for DCMT 11T3 Indexable Inserts Precise Clamping for Stable Turning The Holder is engineered to provide consistent Clamping Force during Turning operations. With an ISO designation of SDJCR 1212, the design secures DCMT Inserts reliably, reducing vibration and improving Surface Finish. The reinforced Clamping geometry and a dedicated Clamping Screw interface yield repeatable results in short runs and serial production alike, enhancing Tool Life and process stability. Compact Dimensions with Clear Compatibility Compact Dimensions (12 mm Width, 12 mm Height) and a total Length of 110 mm make the Holder easy to mount on common Tool Posts. Compatibility with the U Plate TA030 and Shank Designation J11-IC simplifies integration. The combination of measured Cutting Height and a 93° Cutting Angle ensures predictable tool engagement and reproducible Turning geometry for a range of materials. Internal Coolant for Improved Chip Control Built-in Internal Coolant channels deliver coolant close to the cutting edge, aiding Chip Evacuation and cooling the Insert locally. This feature reduces Thermic Stress on the Insert and can extend edge life in demanding operations. For users less familiar with Internal Coolant, this means coolant exits through the Holder to the Insert Seat, improving Lubrication and helping maintain consistent Cutting Conditions. Assembly, Fastening and Practical Handling The Holder uses standard Fasteners for straightforward setup: the U Plate Screw is M5, the Torx Screw is M3.5x11 and the Torx Key required is T15. These common Fastener Sizes allow quick replacement of Inserts and routine Maintenance. The right-hand Cutting Direction is clearly marked, and the Holder’s Cutting Head Width of 16 mm supports a stable Insert seating for turning operations. Strongly recommended: Choose the AP509TM Clamping Holder from Teknik Makina for reliable right-hand turning with DCMT 11T3 inserts — for technical queries or fast supply, contact Metav Werkzeuge at info@metav-werkzeuge.com or +49 2822 7131930. Specifications Specifications SKU: AP509TM Brand: Teknik Makina Description: SDJC for DCMT Indexable Inserts ISO Designation: SDJCR 1212 U Plate: TA030 Shank Designation: J11-IC Data Holder Width: 12 mm Holder Height: 12 mm Cutting Head Width: 16 mm Cutting Height: 32 mm Total Height: 12 mm Total Length: 110 mm Cutting Angle: 93° Features Internal Coolant: internal cooling for improved chip evacuation Clamping Screw: M5 Torx Screw: M3.5x11 (Torx Screw specification) Torx Key: T15 (Torx Key for assembly) Suitable Inserts: DCMT 11T3 Shank: J11-IC Cutting Direction: Right FAQ What inserts fit this holder? The AP509TM Clamping Holder from Teknik Makina is designed for DCMT 11T3 Indexable Inserts; the SDJC Geometry secures these Inserts with stable seating for turning applications. Does the holder support internal coolant? Yes, the AP509TM includes Internal Coolant channels to guide coolant directly to the Insert, improving Chip Evacuation and reducing local Heat Build-up during Turning. Which fasteners and key are required for assembly? Assembly uses an M5 U Plate Screw and Torx Screw M3.5x11; the specified Torx Key is T15 for tightening and maintenance of the AP509TM Holder. Is the holder right- or left-hand? This AP509TM Tool is configured for Right-hand Cutting Direction and is intended for Right-hand Turning operations. Manufacturer: Teknik Makina, Nolu Sokak, No 9, Selcuklu, Türkiye, eMail: info@teknik-makina.com / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Turning Holder SDJCL 2525 for DCMT 11T3 Indexable Inserts by Teknik Makina The Turning Holder SDJCL 2525 is a robust lathe tool holder designed for precise left‑hand turning with DCMT 11T3 indexable inserts, suitable for professional workshop use and production environments. Compatible with DCMT 11T3 indexable inserts 150 mm overall length for stable tool overhang Internal Coolant for improved chip evacuation Secure clamping with Torx T15 and M3.5x11 screws 93° cutting angle for reliable left‑hand turning Precision and Compatibility that Reduce Set‑up Time The SDJCL 2525 holder has been engineered to accept DCMT 11T3 indexable inserts, enabling quick insert changes and consistent cutting geometry. By matching the insert pocket precisely, the holder minimizes runout and vibration, which leads to more predictable surface finish and longer insert life. For users unfamiliar with insert codes: DCMT denotes a double‑sided, rhombic insert type with a 55° diamond shape; this holder ensures correct seating and orientation so the tool performs as intended without repeated adjustments. Practical Workshop Features for Reliable Operation With a 150 mm overall length and a 93° cutting angle for left‑hand operations, this holder balances accessibility and rigidity to support stable turning. The Internal Coolant channel directs fluid close to the cutting edge, helping to control temperature and chip flow while reducing thermal wear on the insert. Clamping and maintenance are simplified by the Torx T15 drive and M3.5x11 screws, which provide reproducible torque and secure fixation—advantages that reduce downtime during tool changes in busy shop environments. Who Benefits and How to Integrate It into Your Process Machinists and production technicians who require repeatable left‑hand turning will find this turning holder especially useful. Its 25 mm width and 25 mm height make it compatible with standard toolposts for small to medium turning applications, while the 32 mm Schneidkopf (cutting‑head) width offers a stable seat for the insert. When integrating the holder, confirm insert type DCMT 11T3 and the left‑hand orientation; correct pairing yields consistent cutting forces and predictable chip control. For assistance selecting the right holder for a specific machine or application, expert support is available. For workshops seeking durable, production‑ready tooling we recommend the Teknik Makina Turning Holder SDJCL 2525 — for tailored advice and ordering assistance contact METAV Werkzeuge at info@metav-werkzeuge.com or call +49 2822 7131930 (WhatsApp +49 170 2837271). Technical Details Turning Holder Brand: Teknik Makina SKU: AP517TM Compatible Inserts: DCMT 11T3 ISO Designation: SDJCL 2525 Overall Length: 150 mm Width: 25 mm Height: 25 mm Cutting‑head Width: 32 mm Cutting Angle: 93° Cutting Direction: Left Internal Coolant: Yes Torx Key: T15 Torx Screw: M3.5x11 U Plate: TA030 Manufacturer: Teknik Makina, Nolu Sokak, No 9, Selcuklu, Turkey, eMail: info@teknik-makina.com Responsible Person: Metav Werkzeuge GmbH, Parkring 45, 46446 Emmerich, eMail: info@metav-werkzeuge.com FAQ Which inserts fit the Turning Holder SDJCL 2525 from Teknik Makina? The Turning Holder SDJCL 2525 by Teknik Makina is designed for DCMT 11T3 indexable inserts; pairing this holder with the specified insert type ensures correct seating, cutting geometry and optimal performance. Does the Teknik Makina Turning Holder SDJCL 2525 support internal coolant? Yes, the Teknik Makina Turning Holder SDJCL 2525 features Internal Coolant, which channels fluid to the cutting zone to improve chip evacuation and reduce thermal loading on the insert. Is the Turning Holder SDJCL 2525 suitable for left‑hand turning only? The SDJCL 2525 turning holder is configured for left‑hand cutting direction as specified by Teknik Makina; for right‑hand operations a corresponding right‑hand holder should be chosen. How do I secure the insert and perform maintenance on the Teknik Makina Turning Holder SDJCL 2525? Clamping is accomplished using the Torx T15 interface and M3.5x11 screws supplied; regular checks of screw torque and coolant channels will keep the Turning Holder SDJCL 2525 operating reliably—METAV Werkzeuge can advise on torque settings and maintenance routines if needed. {"@context":"https://schema.org","@graph":[{"@type":"Product","@id":"#AP517TM","sku":"AP517TM","mpn":"AP517TM","gtin13":"4061905052248","name":"150mm SDJCL 2525 93° SDJC for DCMT Indexable Inserts","description":"SDJC turning holder for DCMT 11T3 indexable inserts, 150 mm overall length, coolant-through, left cutting, robust construction by Teknik Makina.","image":["https://files.plytix.com/api/v1.1/file/public_files/pim/assets/57/c3/98/62/6298c3575d155f1bc7e497fd/images/09/8d/e2/62/62e28d0933927e49dbf377ea/ap515tm-main.jpg"],"additionalProperty":[{"@type":"PropertyValue","name":"Compatible inserts","value":"DCMT 11T3"},{"@type":"PropertyValue","name":"Overall length","value":"150 mm"},{"@type":"PropertyValue","name":"Weight","value":"0.735 kg"},{"@type":"PropertyValue","name":"ISO designation","value":"SDJCL 2525"},{"@type":"PropertyValue","name":"Shank designation","value":"M11"},{"@type":"PropertyValue","name":"Width","value":"25 mm"},{"@type":"PropertyValue","name":"Height","value":"25 mm"},{"@type":"PropertyValue","name":"Cutting head width","value":"32 mm"},{"@type":"PropertyValue","name":"Cutting angle","value":"93°"},{"@type":"PropertyValue","name":"Coolant-through","value":"yes"},{"@type":"PropertyValue","name":"Cutting direction","value":"left"}]},{"@type":"FAQPage","mainEntity":[{"@type":"Question","name":"Which inserts fit this holder?","acceptedAnswer":{"@type":"Answer","text":"DCMT 11T3 indexable inserts."}},{"@type":"Question","name":"What is the overall length?","acceptedAnswer":{"@type":"Answer","text":"150 mm overall length."}},{"@type":"Question","name":"Does it support coolant-through?","acceptedAnswer":{"@type":"Answer","text":"Yes, the holder is coolant-through."}},{"@type":"Question","name":"What is the cutting angle?","acceptedAnswer":{"@type":"Answer","text":"Cutting angle 93°."}},{"@type":"Question","name":"Is the cutting direction left or right?","acceptedAnswer":{"@type":"Answer","text":"Left cutting direction."}},{"@type":"Question","name":"What is the ISO designation?","acceptedAnswer":{"@type":"Answer","text":"ISO designation SDJCL 2525."}}]},{"@type":"ItemPage","url":"https://metav-shop.de/","dateModified":"2026-04-16T12:00:00+01:00","author":{"@type":"Person","name":"Stephan Bayer","url":"https://www.linkedin.com/in/stephan-bayer/"},"publisher":{"@type":"Organization","name":"Metav Werkzeuge GmbH","url":"https://metav-shop.de","logo":{"@type":"ImageObject","url":"https://files.plytix.com/api/v1.1/file/public_files/pim/assets/57/c3/98/62/6298c3575d155f1bc7e497fd/images/8e/48/c5/69/69c5488eb2b3400ba580741c/logo-metav-1200-675.png","width":1200,"height":675},"address":{"@type":"PostalAddress","streetAddress":"Parkring 45","postalCode":"46446","addressLocality":"Emmerich","addressCountry":"DE"},"telephone":"+49 2822 7131930","email":"info@metav-werkzeuge.com"},"about":[{"@type":"Thing","name":"Turning Holder"},{"@type":"Thing","name":"SDJC for DCMT Indexable Inserts"},{"@type":"Thing","name":"Coolant-through tooling"}],"mentions":[{"@type":"Thing","name":"Teknik Makina"}]}]}

Turning Holder (SDJCL 2020) for DCMT 11T3 Inserts — Teknik Makina The Turning Holder is a robust clamping tool designed for left-hand turning with DCMT 11T3 indexable inserts, suited for precise metalworking on lathes and tooling stations. Compatible with DCMT 11T3 Inserts 125 mm Overall Length for stable reach Internal Cooling for improved Chip Removal 93° Cutting Angle for consistent Engagement Torx T15 Fastening with M3.5x11 Screw Secure Clamping for Consistent Turning Results The Turning Holder combines a Rigid Clamp with a precisely milled Cutting Head to deliver repeatable results in Turning operations. With an ISO Designation of SDJCL 2020 and a Schneidekopf Breite/ Cutting Head Width of 25 mm, the tool ensures stable Insert Seating and minimal Vibration. This stability reduces Insert Wear and improves Surface Finish, so machinists benefit from longer tool life and fewer interruptions during production runs. Improved Cooling and Chip Management for Longer Insert Life Equipped with Internal Cooling (Yes), the holder channels Coolant directly to the Cutting Edge to reduce Temperature at the Tool-Workpiece Interface. This targeted Cooling lowers Thermal Stress on Indexable Inserts and supports better Chip Evacuation, which is particularly useful in continuous Turning and interrupted cuts. Compatible with DCMT 11T3 Inserts, the system helps maintain Cutting Conditions that extend Insert Service Life and maintain Dimensional Accuracy. Designed for Precision and Ease of Use in Workshop Environments With a Total Length of 125 mm, a Body Width of 20 mm and Height of 20 mm, the Turning Holder balances Reach and Rigidity for common Lathe Setups. The 93° Cutting Angle is optimized for left-hand Cutting Direction, providing predictable Chip Flow and consistent Cutting Forces. Assembly and Insert Changes are straightforward thanks to the Torx T15 interface and the supplied M3.5x11 Screw, enabling quick tool swaps and reduced Setup Time. Target Applications and Who Benefits Most This Turning Holder is aimed at Professional Machinists and Toolroom Technicians working on steel, non-ferrous alloys and general Turning tasks that require reliable clamping and coolant delivery. The combination of DCMT 11T3 Compatibility and Internal Cooling makes the holder suitable for medium to high-precision production, prototype Turning and workshop repairs where stable Cutting conditions and fast Insert changes are valued. Choose Teknik Makina's Turning Holder for dependable left-hand turning performance — for personalised technical advice or to confirm compatibility with your machining setup, contact METAV Werkzeuge: info@metav-werkzeuge.com | Tel: +49 2822 7131930 | WhatsApp: +49 170 2837271. Bezeichnung: Klemmhalter Brand: Teknik Makina SKU: AP516TM Suitable Inserts: DCMT 11T3 Total Length: 125 mm Weight: 0.404 kg ISO Designation: SDJCL 2020 Secondary Designation: K11 Width: 20 mm Height: 20 mm Cutting Head Width: 25 mm Cutting Height: 32 mm Cutting Direction: Left Cutting Angle: 93° Internal Cooling: Yes Torx Key: T15 Torx Screw: M3.5x11 U-Plate: TA030 Manufacturer: Teknik Makina, Nolu Sokak, No 9, Selcuklu, Türkei, eMail: info@teknik-makina.com Responsible Person: Metav Werkzeuge GmbH, Parkring 45, 46446 Emmerich, eMail: info@metav-werkzeuge.com FAQ What Inserts fit the Turning Holder from Teknik Makina? The Turning Holder by Teknik Makina is engineered for DCMT 11T3 indexable inserts, ensuring precise seating and reliable clamping when used with the SDJCL 2020 configuration. Does the Turning Holder support coolant supply? Yes, the Teknik Makina Turning Holder features Internal Cooling, which directs Coolant to the Cutting Zone to improve Chip Control and reduce Thermal Load on the Insert. Is the Turning Holder suitable for left-hand machining only? The holder is specified for Left cutting direction with a 93° Cutting Angle; it is optimized for left-hand Turning applications and setups. How do I tighten the insert on the Turning Holder? Assembly uses a Torx T15 interface and an M3.5x11 screw for secure fastening; the design permits fast Insert changes and straightforward maintenance. Need help selecting the right holder for your machine? If uncertain whether the Teknik Makina Turning Holder fits your requirements, METAV Werkzeuge offers expert advice — contact info@metav-werkzeuge.com or call +49 2822 7131930. {"@context":"https://schema.org","@graph":[{"@type":"Product","@id":"#AP516TM","sku":"AP516TM","mpn":"SDJCL 2020","gtin13":"4061905052231","name":"SDJCL 2020 Turning Holder 125mm, 93° for DCMT 11T3","description":"Turning holder SDJCL 2020, 125 mm overall length, for DCMT 11T3 indexable inserts; left cutting direction; internal coolant; robust 20x20 mm shank.","image":["https://files.plytix.com/api/v1.1/file/public_files/pim/assets/57/c3/98/62/6298c3575d155f1bc7e497fd/images/09/8d/e2/62/62e28d0933927e49dbf377ea/ap515tm-main.jpg"],"additionalProperty":[{"@type":"PropertyValue","name":"Compatible inserts","value":"DCMT 11T3"},{"@type":"PropertyValue","name":"Overall length","value":"125 mm"},{"@type":"PropertyValue","name":"Shank width","value":"20 mm"},{"@type":"PropertyValue","name":"Shank height","value":"20 mm"},{"@type":"PropertyValue","name":"Cutting head width","value":"25 mm"},{"@type":"PropertyValue","name":"Cutting angle","value":"93°"},{"@type":"PropertyValue","name":"Cutting direction","value":"left"},{"@type":"PropertyValue","name":"Internal coolant","value":"yes"},{"@type":"PropertyValue","name":"Weight","value":"0.404 kg"},{"@type":"PropertyValue","name":"ISO designation","value":"SDJCL 2020"},{"@type":"PropertyValue","name":"Variant designation","value":"K11"},{"@type":"PropertyValue","name":"Manufacturer","value":"Teknik Makina"}]},{"@type":"FAQPage","mainEntity":[{"@type":"Question","name":"What inserts fit this holder?","acceptedAnswer":{"@type":"Answer","text":"DCMT 11T3 indexable inserts."}},{"@type":"Question","name":"What is the overall length?","acceptedAnswer":{"@type":"Answer","text":"Overall length is 125 mm."}},{"@type":"Question","name":"Does it have internal coolant?","acceptedAnswer":{"@type":"Answer","text":"Yes, the holder supports internal coolant."}},{"@type":"Question","name":"What is the cutting angle?","acceptedAnswer":{"@type":"Answer","text":"The cutting angle is 93°."}},{"@type":"Question","name":"What is the shank size?","acceptedAnswer":{"@type":"Answer","text":"Shank size is 20 mm x 20 mm."}}]},{"@type":"ItemPage","url":"https://metav-shop.de/klemmhalter-sdjcl-2020-93-dcmt-11t3","dateModified":"2026-03-31T12:00:00+01:00","author":{"@type":"Person","name":"Stephan Bayer","url":"https://www.linkedin.com/in/stephan-bayer/"},"publisher":{"@type":"Organization","name":"Metav Werkzeuge GmbH","url":"https://metav-shop.de","logo":{"@type":"ImageObject","url":"https://files.plytix.com/api/v1.1/file/public_files/pim/assets/57/c3/98/62/6298c3575d155f1bc7e497fd/images/8e/48/c5/69/69c5488eb2b3400ba580741c/logo-metav-1200-675.png","width":1200,"height":675},"address":{"@type":"PostalAddress","streetAddress":"Parkring 45","postalCode":"46446","addressLocality":"Emmerich","addressCountry":"DE"},"telephone":"+49 2822 7131930","email":"info@metav-werkzeuge.com"},"about":[{"@type":"Thing","name":"Turning Holder SDJCL 2020"},{"@type":"Thing","name":"Indexable Inserts DCMT 11T3"},{"@type":"Thing","name":"Left Cutting Direction"}],"mentions":[{"@type":"Thing","name":"Internal Coolant"},{"@type":"Thing","name":"20x20 mm Shank"},{"@type":"Thing","name":"K11 Variant"},{"@type":"Thing","name":"93° Cutting Angle"}]}]}

Turning Holder — SDJC for DCMT Indexable Inserts by Teknik Makina The Turning Holder SDJC for DCMT indexable inserts provides stable left-hand cutting for precise external turning in metalworking applications. Compatible with DCMT 11T3 indexable inserts 100 mm overall length for extended reach Internal cooling for improved chip control SDJCL 1616 ISO shank for secure clamping 93° cutting angle for accurate external turning Precise geometry for consistent external turning The SDJCL 1616 shank and a 93° cutting angle combine to deliver predictable tool engagement and consistent surface finish on workpieces. This design reduces vibration during left-hand operations and makes setup more reliable, so toolpaths remain accurate even at higher cutting speeds. The result is improved productivity through fewer reworks and more repeatable parts. Internal cooling that keeps chips under control Equipped with internal cooling, the holder channels cutting fluid directly to the cutting zone, which improves chip control and helps maintain cutting-edge temperature. Better heat management extends insert life and supports more stable machining on interrupted cuts. For operators, this means longer tool life and fewer insert changes during batch production. Designed for fast service and broad compatibility This turning holder is built for DCMT 11T3 indexable inserts and a quick-change workflow; the clamping geometry ensures secure seating and simple insert replacement. The Torx attachment uses a Torx T15 interface with an M3.5x11 screw for reliable fastening, allowing rapid maintenance without complex tools. Workshops benefit from reduced downtime and straightforward handling. Who benefits and where it excels Machinists working on external turning tasks, maintenance shops and small series production will find the holder ideal for stable, accurate cuts. Manufactured by Teknik Makina, the component is targeted at users who require a compact, dependable tool holder for left-hand operations and precise finishes. If tighter tolerances or specific machining strategies are needed, technical support from METAV Werkzeuge is available to assist. Choose Teknik Makina’s Turning Holder for reliable left-hand external turning and contact METAV Werkzeuge for expert advice and technical support at info@metav-werkzeuge.com or +49 2822 7131930 (WhatsApp: +49 170 2837271). Turning Holder Brand: Teknik Makina SKU: AP515TM For indexable inserts: DCMT 11T3 Overall length: 100 mm ISO designation: SDJCL 1616 Secondary designation: H11 Width: 16 mm Height: 16 mm Cutting head width: 16 mm Cutting height: 32 mm Cutting direction: left Cutting angle: 93° Internal cooling: true Torx key: T15 Torx screw: M3.5x11 U plate: TA030 GTIN: 4061905052224 Availability: in Stock Condition: new Manufacturer: Teknik Makina, Nolu Sokak, No 9, Selcuklu, Turkey, eMail: info@teknik-makina.com Responsible Person: Metav Werkzeuge GmbH, Parkring 45, 46446 Emmerich, eMail: info@metav-werkzeuge.com FAQ What inserts fit the Turning Holder from Teknik Makina? The Turning Holder from Teknik Makina is compatible with DCMT 11T3 indexable inserts; these inserts are mounted with a secure clamping geometry suited for external turning and allow fast replacement for efficient workshop operation. Does the Turning Holder include internal cooling? Yes, the Turning Holder by Teknik Makina features internal cooling, which improves chip evacuation and helps maintain insert life and surface quality during demanding cuts. Is this Turning Holder suitable for left-hand cutting only? The Turning Holder is specified for left-hand cutting direction; Teknik Makina designed the toolholder geometry and cutting angle to perform optimally in left-hand external turning applications. How can METAV Werkzeuge help with this Turning Holder? METAV Werkzeuge offers technical consultation for the Turning Holder by Teknik Makina; contact info@metav-werkzeuge.com or call +49 2822 7131930 for application advice, compatibility checks or additional technical data. 93° SDJCL 1616 Turning Holder for DCMT 11T3, 100mm, Internal Coolant - Teknik Makina

Technical Data: Order Number: AP512TM Item: Turning Holder usable with DCMT 11T3 Indexable Inserts Brand: Teknik Makina ISO Code: SDJCR 2525 M11-IK Structural Details: Weight: 0.735kg Total length: 150mm Cutting Height: 35mm Additional Informattion Cutting Direction: rechts Cooling Manufacturer Teknik Makina, Nolu Sokak, No 9, Selcuklu, Turkey, eMail: info@teknik-makina.com Responsible for Europe Metav Werkzeuge GmbH, Parkring 45, 46446 Emmerich, Germany, eMail: info@metav-werkzeuge.com

Turning Holder (Klemmhalter) SDJCR 2020 for DCMT 11T3 — Teknik Makina The Turning Holder SDJCR 2020 is a precision clamping tool for DCMT 11T3 indexable inserts, engineered for right-hand external turning with integrated internal cooling. SDJCR 2020 Interface for DCMT 11T3 Inserts Integrated internal cooling for stable cutting 125 mm overall length for versatile reach 20 × 20 mm shank for secure clamping 93° cutting angle for precise right-hand cuts Reliable Interface and Simple Compatibility for Faster Setups Built with the SDJCR 2020 interface, this clamping solution accepts DCMT 11T3 indexable inserts and simplifies tool changes. The clear adherence to the DCMT insert format means compatibility with widely used carbide inserts, so setups are faster and stocking multiple insert types is easier. For users unfamiliar with indexable inserts: these are replaceable carbide cutting tips that allow economical reuse of the holder body while restoring cutting performance quickly. Better Chip Control and Tool Life Through Internal Cooling Thanks to internal cooling, coolant is delivered directly to the cutting zone, improving chip evacuation and temperature control during machining. This focused cooling reduces thermal stress on the insert and the workpiece, which can extend tool life and produce more consistent surface finishes. For workshops aiming to optimize cycle times, the cooling feature supports longer uninterrupted runs and reduces manual intervention. Robust Dimensions for Stable Turning and Reduced Vibration With a 125 mm overall length and a 20 × 20 mm shank cross-section, the holder provides a stable interface between lathe turret and cutting tip, limiting deflection during cutting. The 25 mm cutting-head width and 93° cutting angle are tuned for accurate right-hand external profiling and facing tasks. Reduced vibration leads to improved dimensional accuracy and a cleaner component surface with fewer secondary operations. Practical Fastening and Replacement Details for Maintenance Maintenance is straightforward: the holder uses a T15 Torx key for the clamping screw and standard M3.5×11 Torx screws for secure assembly, simplifying routine checks and insert changes. The holder's designation as a clamping-style tool (Klemmhalter) makes it easy to service in busy shops where uptime is critical. Clear access to fastening points shortens intervention times and helps keep machines productive. Who Benefits Most: Shops Focused on Efficiency and Flexibility Machine shops and workshops that require rapid insert swaps, reliable coolant delivery, and a compact, rigid toolholder will find this solution advantageous. The holder supports efficient serial production as well as flexible prototyping runs where quick setup changes and consistent cut quality matter. For turning tasks demanding repeatability and minimal downtime, this clamping holder is a practical choice. We recommend the Teknik Makina Turning Holder for machinists seeking improved chip control and consistent right-hand turning performance; for further advice or to confirm fitment, contact METAV Werkzeuge — eMail: info@metav-werkzeuge.com, Tel: +49 2822 7131930, WhatsApp: +49 170 2837271. Designation: Klemmhalter (Turning Holder) SDJCR 2020 for DCMT 11T3 Brand: Teknik Makina SKU: AP511TM For Inserts: DCMT 11T3 ISO Designation: SDJCR 2020 Overall Length: 125 mm Weight: 0.404 kg Shank Width: 20 mm Shank Height: 20 mm Cutting Head Width: 25 mm Cutting Height: 32 mm Cutting Angle: 93° Direction of Cut: Right Internal Cooling: Yes Torx Key: T15 Torx Screw: M3.5×11 U-Plate: TA030 Manufacturer: Teknik Makina, Nolu Sokak, No 9, Selcuklu, Turkey, eMail: info@teknik-makina.com Responsible Person: Metav Werkzeuge GmbH, Parkring 45, 46446 Emmerich, eMail: info@metav-werkzeuge.com FAQ What inserts fit the Turning Holder from Teknik Makina? The Teknik Makina Turning Holder SDJCR 2020 is designed specifically for DCMT 11T3 indexable inserts, ensuring direct compatibility with that insert format for straightforward mounting and replacement. Does the Turning Holder support coolant-through functionality? Yes, the Teknik Makina Turning Holder includes internal cooling, which channels coolant to the cutting edge to aid chip evacuation and temperature control during machining. Which cutting direction is the holder intended for? The Teknik Makina Turning Holder is configured for right-hand turning operations and features a 93° cutting angle optimized for external profiling and facing. How can I get technical advice or confirm suitability for my machine? If you need help determining whether the Teknik Makina Turning Holder fits your application, METAV Werkzeuge offers comprehensive advice — eMail: info@metav-werkzeuge.com or call +49 2822 7131930, WhatsApp +49 170 2837271. 125mm SDJCR Turning Holder for DCMT 11T3, 93° Right, Internal Coolant - Teknik Makina

Turning Holder SDJC for DCMT 11T3 Indexable Inserts by Teknik Makina The Turning Holder is a robust toolholder for left-hand turning, engineered to securely carry DCMT 11T3 indexable inserts in demanding metalcutting applications. Turning Holder for DCMT 11T3 indexable inserts 150 mm overall length for stable support 93° cutting angle for reliable chip control 32 mm cutting head width for robust performance Left-hand cutting, ISO SDJCL 2525 designation Maximised Stability for Precise Turning Results Heavy-duty construction delivers stability where it matters: the holder’s 150 mm overall length and 32 mm cutting head width reduce deflection during engaging cuts. This increases process reliability and allows operators to maintain consistent surface finishes with fewer interruptions. The design focuses on one clear benefit — higher part quality through reduced tool vibration. Engineered Compatibility and Clear Setup Benefits Designed specifically for DCMT 11T3 indexable inserts, the toolholder simplifies setup and reduces guessing during insert changes. The ISO designation SDJCL 2525 ensures predictable clamping geometry and repeatable seating, so fitting an insert is straightforward even in fast-paced production. For machinists, this means shorter set-up times and fewer alignment adjustments per batch. Optimised Cutting Geometry for Controlled Chip Flow A 93° cutting angle contributes to chip control and effective heat distribution at the cutting edge, especially for left-hand turning operations. That geometry helps maintain tool life under cyclic loads and supports smoother feeds on a range of materials. For processes requiring consistent chip evacuation, this feature translates into fewer stoppages and improved cycle stability. Who Benefits from This Toolholder Workshops and manufacturers focusing on turning operations with indexable inserts will find the holder particularly suited to small- and medium-batch production where tool reliability and speed matter. The toolholder is appropriate for skilled operators and production teams seeking predictable tool behaviour and straightforward compatibility with DCMT 11T3 inserts. We recommend the Teknik Makina Turning Holder for precision left-hand turning; contact METAV Werkzeuge for personalised advice and implementation support — eMail: info@metav-werkzeuge.com, Tel: +49 2822 7131930, WhatsApp: +49 170 2837271 Designation: Turning Holder Brand: Teknik Makina SKU: D368TM Compatible Inserts: DCMT 11T3 Overall Length: 150 mm Weight: 0.735 kg ISO Designation: SDJCL 2525 Secondary Designation: SDJC for DCMT Indexable Inserts Shank Width: 25 mm Shank Height: 25 mm Cutting Head Width: 32 mm Cutting Height: 30 mm Cutting Direction: Left Cutting Angle: 93° GTIN: 4061905153327 Availability: in Stock Condition: new Manufacturer: Teknik Makina, Nolu Sokak, No 9, Selcuklu, Turkey, eMail: info@teknik-makina.com Responsible Person: Metav Werkzeuge GmbH, Parkring 45, 46446 Emmerich, eMail: info@metav-werkzeuge.com FAQ What inserts are compatible with the Turning Holder from Teknik Makina? The Turning Holder from Teknik Makina is compatible with DCMT 11T3 indexable inserts; the holder’s geometry and the ISO designation SDJCL 2525 ensure secure seating and repeatable clamping for these inserts. Can the Teknik Makina Turning Holder be used for right-hand operations? The Teknik Makina Turning Holder is specified for left-hand cutting direction; for right-hand applications, please consult METAV Werkzeuge to verify alternative holders or configurations suitable for right-hand turning. How does the 93° cutting angle benefit machining with the Teknik Makina Turning Holder? A 93° cutting angle on the Teknik Makina Turning Holder helps with chip control and heat distribution, improving tool life and surface finish by reducing edge loading in demanding turning operations. Who should I contact for technical advice on installing the Turning Holder? For tailored setup guidance and additional technical data for the Turning Holder by Teknik Makina, contact METAV Werkzeuge — eMail: info@metav-werkzeuge.com or Tel: +49 2822 7131930; WhatsApp: +49 170 2837271. {"@context":"https://schema.org","@graph":[{"@type":"Product","@id":"#D368TM","sku":"D368TM","mpn":"D368TM","gtin13":"4061905153327","name":"SDJCL 2525 Turning Holder for DCMT 11T3, 93° Left","description":"150mm turning holder for DCMT 11T3 indexable inserts; ISO SDJCL 2525; 25x25mm shank, 32mm cutting head width; left-hand, 93° cut; Manufacturer: Teknik Makina","image":["https://files.plytix.com/api/v1.1/file/public_files/pim/assets/57/c3/98/62/6298c3575d155f1bc7e497fd/images/9f/13/35/64/6435139f4fcfb37a48907531/d360tm-main.png","https://files.plytix.com/api/v1.1/file/public_files/pim/assets/57/c3/98/62/6298c3575d155f1bc7e497fd/images/d0/7e/de/62/62de7ed00f56dbb4de4dbf3f/d360tm-technische-zeichnung.jpg","https://files.plytix.com/api/v1.1/file/public_files/pim/assets/57/c3/98/62/6298c3575d155f1bc7e497fd/images/2d/7e/de/62/62de7e2d148ec6b71020ff7a/d360tm-artikelliste.jpg"],"additionalProperty":[{"@type":"PropertyValue","name":"Suitable Inserts","value":"DCMT 11T3"},{"@type":"PropertyValue","name":"Overall Length","value":"150 mm"},{"@type":"PropertyValue","name":"Shank Width","value":"25 mm"},{"@type":"PropertyValue","name":"Shank Height","value":"25 mm"},{"@type":"PropertyValue","name":"Cutting Head Width","value":"32 mm"},{"@type":"PropertyValue","name":"Cutting Height","value":"30 mm"},{"@type":"PropertyValue","name":"Cutting Direction","value":"Left"},{"@type":"PropertyValue","name":"Cutting Angle","value":"93°"},{"@type":"PropertyValue","name":"Weight","value":"0.735 kg"},{"@type":"PropertyValue","name":"ISO Designation","value":"SDJCL 2525"},{"@type":"PropertyValue","name":"Designation 2","value":"M11"}]},{"@type":"FAQPage","mainEntity":[{"@type":"Question","name":"What inserts fit this holder?","acceptedAnswer":{"@type":"Answer","text":"DCMT 11T3 indexable inserts."}},{"@type":"Question","name":"What is the overall length?","acceptedAnswer":{"@type":"Answer","text":"Overall length is 150 mm."}},{"@type":"Question","name":"What are the shank dimensions?","acceptedAnswer":{"@type":"Answer","text":"Shank width and height are 25 mm each."}},{"@type":"Question","name":"What is the cutting angle and direction?","acceptedAnswer":{"@type":"Answer","text":"Cutting angle 93° with left-hand cutting direction."}},{"@type":"Question","name":"Who is the manufacturer?","acceptedAnswer":{"@type":"Answer","text":"Teknik Makina."}}]},{"@type":"ItemPage","url":"https://metav-shop.de/SDJCL-2525-D368TM","dateModified":"2026-03-31T12:00:00+01:00","author":{"@type":"Person","name":"Stephan Bayer","url":"https://www.linkedin.com/in/stephan-bayer/"},"publisher":{"@type":"Organization","name":"Metav Werkzeuge GmbH","url":"https://metav-shop.de","logo":{"@type":"ImageObject","url":"https://files.plytix.com/api/v1.1/file/public_files/pim/assets/57/c3/98/62/6298c3575d155f1bc7e497fd/images/8e/48/c5/69/69c5488eb2b3400ba580741c/logo-metav-1200-675.png","width":1200,"height":675},"address":{"@type":"PostalAddress","streetAddress":"Parkring 45","postalCode":"46446","addressLocality":"Emmerich","addressCountry":"DE"},"telephone":"+49 2822 7131930","email":"info@metav-werkzeuge.com"},"about":[{"@type":"Thing","name":"Turning Holder SDJCL 2525"},{"@type":"Thing","name":"DCMT 11T3 Indexable Inserts"},{"@type":"Thing","name":"Teknik Makina"}],"mentions":[{"@type":"Thing","name":"25x25 mm shank"},{"@type":"Thing","name":"150 mm overall length"},{"@type":"Thing","name":"93° cutting angle"}]}]}

Turning Holder — SDJCL 2020 (for DCMT 11T3 Indexable Inserts) by Teknik Makina The Turning Holder secures DCMT 11T3 indexable inserts for precise left-hand turning operations in a compact, stable 125 mm tool configuration. SDJCL 2020 Holder for DCMT 11T3 Inserts 125 mm Overall Length for stable setup 93° Cutting Angle for predictable chip flow Left-hand Cutting Direction for dedicated turning tasks 25 mm Cutting Head Width for robust insert support Precision and Stability for consistent turning results Built to deliver repeatable machining, this Turning Holder offers a rigid seating and precise alignment for DCMT inserts, which reduces vibration and improves surface finish. The compact 125 mm overall length optimises tool overhang and helps maintain concentricity, so cycle times stay predictable and tool life is extended. This stability translates into fewer rejects and less rework on turned components. Compatible design that simplifies tooling choices The holder accepts DCMT 11T3 indexable inserts and matches the ISO designation SDJCL 2020, making it straightforward to standardise tooling across machines. Compatibility with commonly stocked inserts reduces setup complexity and inventory variety. The configuration supports conventional clamping procedures, so operators can mount and replace inserts quickly without special adapters. Who benefits: targeted application and user profile Machinists and workshop planners needing a reliable left-hand turning solution will appreciate the holder's focused design for turning applications that require controlled chip evacuation and repeatable geometry. Production environments with short setup windows benefit from the holder’s simple interface to DCMT inserts, enabling efficient changeovers and predictable part quality. METAV Werkzeuge provides expert advice for integration and selection if additional specifications are required. Robust geometry for repeatable performance and chip control The tool features a 25 mm cutting head width and a 93° cutting angle that together support stable insert seating and favourable chip formation in many turning operations. Left-hand cutting orientation ensures the holder matches specific machining setups and lathe directions. The holder’s dimensions—20 mm width and 20 mm height—are chosen to balance rigidity with space-efficient mounting, offering reliable clamping force without excessive bulk. Strongly recommend Teknik Makina Turning Holder for demanding turning tasks—contact METAV Werkzeuge for tailored advice and technical support: eMail info@metav-werkzeuge.com | Tel +49 2822 7131930 | WhatsApp +49 170 2837271 Technical Data Designation: Turning Holder (Klemmhalter) Brand: Teknik Makina SKU: D366TM Compatible Inserts: DCMT 11T3 Overall Length: 125 mm Weight: 0.404 kg ISO Designation: SDJCL 2020 Alternate Designation: K11 Width: 20 mm Height: 20 mm Cutting Head Width: 25 mm Cutting Direction: left Cutting Angle: 93° GTIN: 4061905153310 Manufacturer: Teknik Makina, Nolu Sokak, No 9, Selcuklu, Türkei, eMail: info@teknik-makina.com Responsible Person: Metav Werkzeuge GmbH, Parkring 45, 46446 Emmerich, eMail: info@metav-werkzeuge.com FAQ What inserts fit the Turning Holder from Teknik Makina and which ISO code applies? The Turning Holder by Teknik Makina is designed for DCMT 11T3 indexable inserts and uses the ISO designation SDJCL 2020, ensuring compatibility with common DCMT insert variants. Is this holder suitable for left-hand turning operations? Yes, the Teknik Makina Turning Holder is configured for left-hand cutting direction and is intended specifically for turning tasks that require that orientation. How does the 93° cutting angle affect machining with this Turning Holder? A 93° cutting angle supports controlled chip flow and consistent engagement of the DCMT insert, which helps maintain surface finish and predictable cutting forces during turning cycles. Can METAV Werkzeuge assist with selecting the right Turning Holder for my lathe? METAV Werkzeuge offers comprehensive advice for tooling choices; contact them at info@metav-werkzeuge.com or +49 2822 7131930 for personalised support regarding the Teknik Makina Turning Holder. {"@context":"https://schema.org","@graph":[{"@type":"Product","@id":"#D366TM","sku":"D366TM","mpn":"D366TM","gtin13":"4061905153310","name":"125mm SDJCL 2020 Turning Holder for DCMT 11T3 Inserts, 93° Left - Teknik Makina","description":"Turning holder SDJC for DCMT indexable inserts, 125 mm overall length, 93° cutting angle, left-hand; robust 20x20 mm shank and 25 mm cutting head width.","image":["https://files.plytix.com/api/v1.1/file/public_files/pim/assets/57/c3/98/62/6298c3575d155f1bc7e497fd/images/9f/13/35/64/6435139f4fcfb37a48907531/d360tm-main.png","https://files.plytix.com/api/v1.1/file/public_files/pim/assets/57/c3/98/62/6298c3575d155f1bc7e497fd/images/2d/7e/de/62/62de7e2d148ec6b71020ff7a/d360tm-artikelliste.jpg","https://files.plytix.com/api/v1.1/file/public_files/pim/assets/57/c3/98/62/6298c3575d155f1bc7e497fd/images/d0/7e/de/62/62de7ed00f56dbb4de4dbf3f/d360tm-technische-zeichnung.jpg"],"additionalProperty":[{"@type":"PropertyValue","name":"Suitable Inserts","value":"DCMT 11T3"},{"@type":"PropertyValue","name":"Overall Length","value":"125 mm"},{"@type":"PropertyValue","name":"Shank Width","value":"20 mm"},{"@type":"PropertyValue","name":"Shank Height","value":"20 mm"},{"@type":"PropertyValue","name":"Cutting Head Width","value":"25 mm"},{"@type":"PropertyValue","name":"Cutting Angle","value":"93°"},{"@type":"PropertyValue","name":"Direction","value":"Left"},{"@type":"PropertyValue","name":"ISO Designation","value":"SDJCL 2020"},{"@type":"PropertyValue","name":"Weight","value":"0.404 kg"},{"@type":"PropertyValue","name":"Secondary Designation","value":"K11"}]},{"@type":"FAQPage","mainEntity":[{"@type":"Question","name":"What inserts fit this holder?","acceptedAnswer":{"@type":"Answer","text":"DCMT 11T3 indexable inserts fit this holder."}},{"@type":"Question","name":"What is the overall length?","acceptedAnswer":{"@type":"Answer","text":"Overall length is 125 mm."}},{"@type":"Question","name":"What is the cutting angle?","acceptedAnswer":{"@type":"Answer","text":"Cutting angle is 93°."}},{"@type":"Question","name":"Is the holder left- or right-hand?","acceptedAnswer":{"@type":"Answer","text":"This is a left-hand holder."}},{"@type":"Question","name":"What are the shank dimensions?","acceptedAnswer":{"@type":"Answer","text":"Shank width and height are 20 mm each."}},{"@type":"Question","name":"What is the cutting head width?","acceptedAnswer":{"@type":"Answer","text":"Cutting head width is 25 mm."}}]},{"@type":"ItemPage","url":"https://metav-shop.de/125mm-sdjcl-2020-turning-holder-dcmt-11t3-93-left-teknik-makina","dateModified":"2026-04-16T12:00:00+01:00","author":{"@type":"Person","name":"Stephan Bayer","url":"https://www.linkedin.com/in/stephan-bayer/"},"publisher":{"@type":"Organization","name":"Metav Werkzeuge GmbH","url":"https://metav-shop.de","logo":{"@type":"ImageObject","url":"https://files.plytix.com/api/v1.1/file/public_files/pim/assets/57/c3/98/62/6298c3575d155f1bc7e497fd/images/8e/48/c5/69/69c5488eb2b3400ba580741c/logo-metav-1200-675.png","width":1200,"height":675},"address":{"@type":"PostalAddress","streetAddress":"Parkring 45","postalCode":"46446","addressLocality":"Emmerich","addressCountry":"DE"},"telephone":"+49 2822 7131930","email":"info@metav-werkzeuge.com"},"about":[{"@type":"Thing","name":"Turning Holder Series SDJC"},{"@type":"Thing","name":"Indexable Insert Compatibility: DCMT 11T3"},{"@type":"Thing","name":"Application: Turning, Robust Toolholding"}],"mentions":[{"@type":"Thing","name":"Teknik Makina"},{"@type":"Thing","name":"ISO SDJCL 2020"},{"@type":"Thing","name":"K11 Secondary Designation"}]}]}

Specifications: Order Number: D364TM Item: Turning Holder usable with DCMT 11T3 Indexable Inserts Brand: Teknik Makina ISO Code: SDJCL 1616 H11 Quantitative Characteristics: Weight: 0.204kg Total length: 100mm Cutting Height: 25mm Additional Informattion Cutting Direction: links Manufacturer Teknik Makina, Nolu Sokak, No 9, Selcuklu, Turkey, eMail: info@teknik-makina.com Responsible for Europe Metav Werkzeuge GmbH, Parkring 45, 46446 Emmerich, Germany, eMail: info@metav-werkzeuge.com

Clamping Holder (Turning Holder) by Teknik Makina The Clamping Holder is a robust turning tool designed for secure use with DCMT 11T3 indexable inserts in left-hand turning applications. Clamping Holder SDJCL 1212 for DCMT 11T3 inserts 110 mm Overall Length for Stable Support 93° Cut Angle for Accurate Left-Hand Turning 12 x 12 mm Shank for Compact Rigidity 16 mm Cutting Head Width for Robust Clamping Precision and Repeatability for Production Turning The Clamping Holder delivers consistent results by combining a rigid 12 x 12 mm shank with a 16 mm Cutting Head Width, which together minimize vibration and tool deflection. This rigidity ensures repeatable tolerance adherence across long production runs, reducing scrap rates and rework. The 93° Cut Angle supports stable chip formation in left-hand turning, so setup checks are less frequent and cycle times remain predictable. For machinists seeking reliable part-to-part consistency, this toolholder offers measurable process stability. Faster Setup and Clear Compatibility to Save Time Compatibility with DCMT 11T3 indexable inserts and the ISO designation SDJCL 1212 simplifies tooling decisions and inventory management. Engineers benefit from fewer adapter trials because the holder accepts a widely used insert geometry, enabling quick insert changes and alignment. The overall length of 110 mm provides solid support while maintaining accessibility for varied machine configurations. Clear interface dimensions translate into shorter machine downtime during tooling changes and faster ramp-up after maintenance. Designed for Shops That Demand Robustness and Control Small and medium-sized workshops as well as dedicated turning cells will gain from the holder’s compact footprint and sturdy clamping system. The geometry favors turning operations where left-hand cutting is required and where tight clamping pressure is critical. Since the toolholder is engineered for indexable inserts, it supports cost-effective tool management: cutters can be rotated or replaced without removing the entire holder, lowering total tooling cost per part. This makes the solution particularly suitable for batch production and component families with recurring turning tasks. Expert Support and Practical Advice When Needed When technical details or application recommendations are required, METAV Werkzeuge provides competent, personalised consultation to ensure the holder meets specific process demands. For example, guidance on suitable insert grades or optimal cutting parameters for particular steels can prevent premature edge wear and extend insert life. If there is any uncertainty whether this Turning Holder matches a machine’s turret or a workpiece requirement, METAV Werkzeuge is available to assist with measurements, setup tips, and procurement advice. Choose the Teknik Makina Turning Holder for dependable, precision turning — contact METAV Werkzeuge for tailored guidance via email info@metav-werkzeuge.com, phone +49 2822 7131930 or WhatsApp +49 170 2837271. Technical Specifications Bezeichnung: Clamping Holder Marke: Teknik Makina SKU: D362TM Compatible Inserts: DCMT 11T3 ISO Designation: SDJCL 1212 Bezeichnung 2: J11 Overall Length: 110 mm Shank Width: 12 mm Shank Height: 12 mm Cutting Head Width: 16 mm Cutting Direction: Left Cutting Angle: 93° Weight: 0.132 kg Availability: in Stock Manufacturer: Teknik Makina, Nolu Sokak, No 9, Selcuklu, Turkey, eMail: info@teknik-makina.com Responsible Person: Metav Werkzeuge GmbH, Parkring 45, 46446 Emmerich, eMail: info@metav-werkzeuge.com FAQ What inserts fit the Clamping Holder from Teknik Makina? The Clamping Holder by Teknik Makina is designed to accept DCMT 11T3 indexable inserts; this compatibility ensures straightforward insert selection and interchangeability in standard turning setups. Is the Teknik Makina Turning Holder suitable for left-hand turning only? The Teknik Makina Turning Holder is specified with a left cutting direction and a 93° Cut Angle, making it ideal for left-hand turning operations where that orientation is required. How does the SDJCL 1212 designation affect mounting? The SDJCL 1212 ISO designation for the Teknik Makina Clamping Holder defines the holder geometry and interface, helping users verify fitment with turrets and adapters and streamlining tooling compatibility checks. Can METAV Werkzeuge advise on cutting parameters for this holder? Yes, METAV Werkzeuge offers expert consultation for the Teknik Makina Turning Holder, including recommendations on insert grades and cutting parameters to optimise tool life and part quality. 110mm SDJCL 1212 Turning Holder For DCMT 11T3, 93° - Teknik Makina

Clamping Holder — Turning Holder for DCMT Indexable Inserts by Teknik Makina The Clamping Holder is a precision turning holder designed for DCMT 11T3 indexable inserts, optimised for right-hand external turning and stable metalcutting setups. SDJCR 2525 ISO design for secure clamping Compatible with DCMT 11T3 indexable inserts 150 mm overall length for rigid setups 25 x 25 mm shank for compact toolposts 93° cutting angle for consistent chip control Built for secure, repeatable clamping and longer Insert Life The holder's SDJCR 2525 ISO configuration ensures a firm, repeatable seat for DCMT 11T3 inserts, which directly improves process stability and reduces insert wear. By keeping the Insert position constant, cutting forces remain predictable and finishing quality becomes more consistent. For workshops running small to medium turning batches, this repeatability translates into fewer tool changes and more uptime. Compact dimensions that increase Rigidity and control With an overall length of 150 mm and a shank of 25 mm x 25 mm, the design minimises overhang while providing a robust connection to the toolpost. The 32 mm cutting-head width balances accessibility and support for the Insert, improving heat dissipation and lowering vibration during cuts. These dimensional properties make setup straightforward and help maintain surface finish under typical external turning loads. Designed for straightforward integration into turning setups The holder is configured for right-hand cutting with a 93° cutting angle, giving predictable chip direction and reliable clearance for general turning tasks. The alternative designation M11 indicates the specified mounting/connection interface used for secure fixation in compatible toolholders. Together, these features allow rapid tool changes and simple calibration, so setups remain efficient without compromise to precision. Who benefits and how to apply the holder effectively Workshops, CNC turning centres and maintenance departments that use indexable tooling will find this holder particularly useful when a compact, rigid turning tool is required. Installation is practical for routine external turning and for jobs where predictable chip control matters. For best results, pair the holder with recommended DCMT 11T3 grades tuned to the workpiece material and verify clamping torque to maintain consistent performance. Choose Teknik Makina’s Clamping Holder for reliable, repeatable turning — METAV Werkzeuge offers expert technical advice and personalised support: eMail info@metav-werkzeuge.com • Phone +49 2822 7131930 • WhatsApp +49 170 2837271 Technical specifications for setup and compatibility Bezeichnung: Clamping Holder Marke: Teknik Makina SKU: D228TM For indexable inserts: DCMT 11T3 ISO designation: SDJCR 2525 Secondary designation: M11 Overall length: 150 mm Shank width: 25 mm Shank height: 25 mm Cutting-head width: 32 mm Cutting direction: Right Cutting angle: 93° Weight: 0.735 kg GTIN: 4061905153273 Manufacturer: Teknik Makina, Nolu Sokak, No 9, Selcuklu, Turkey, eMail: info@teknik-makina.com Responsible Person: Metav Werkzeuge GmbH, Parkring 45, 46446 Emmerich, eMail: info@metav-werkzeuge.com FAQ What inserts fit the Clamping Holder from Teknik Makina? The Teknik Makina Clamping Holder is designed for DCMT 11T3 indexable inserts; using the specified insert type ensures correct seating and optimal cutting performance. Is the Clamping Holder suitable for right-hand turning only? Yes, this Clamping Holder is configured for right-hand cutting and a 93° cutting angle, making it suitable for standard external turning applications that require that orientation. How does the SDJCR 2525 designation affect compatibility? The SDJCR 2525 ISO designation defines the holder geometry and clamping method; matching this holder with corresponding toolposts and DCMT 11T3 inserts guarantees proper fit and repeatability. Can METAV Werkzeuge advise on choosing the right insert grade? Absolutely — METAV Werkzeuge provides competent consultation for selecting insert grades and setup parameters to match your machining task; contact info@metav-werkzeuge.com or call +49 2822 7131930 for personalised support. {"@context":"https://schema.org","@graph":[{"@type":"Product","@id":"#D228TM","sku":"D228TM","mpn":"D228TM","gtin13":"4061905153273","name":"Turning Holder SDJCR 2525 93° for DCMT 11T3, 150 mm - Teknik Makina","description":"Turning holder for DCMT 11T3 indexable inserts; ISO SDJCR 2525; overall length 150 mm; right-hand cut; robust 25x25 mm shank.","image":["https://files.plytix.com/api/v1.1/file/public_files/pim/assets/57/c3/98/62/6298c3575d155f1bc7e497fd/images/15/14/35/64/64351415e3692e16d2a37e9e/d220tm-main.png","https://files.plytix.com/api/v1.1/file/public_files/pim/assets/57/c3/98/62/6298c3575d155f1bc7e497fd/images/2d/7e/de/62/62de7e2d33927e49dbf32731/d220tm-artikelliste.jpg","https://files.plytix.com/api/v1.1/file/public_files/pim/assets/57/c3/98/62/6298c3575d155f1bc7e497fd/images/d0/7e/de/62/62de7ed00aced56449540ec0/d220tm-technische-zeichnung.jpg"],"additionalProperty":[{"@type":"PropertyValue","name":"For indexable inserts","value":"DCMT 11T3"},{"@type":"PropertyValue","name":"ISO designation","value":"SDJCR 2525"},{"@type":"PropertyValue","name":"Overall length","value":"150 mm"},{"@type":"PropertyValue","name":"Shank width","value":"25 mm"},{"@type":"PropertyValue","name":"Shank height","value":"25 mm"},{"@type":"PropertyValue","name":"Cutting head width","value":"32 mm"},{"@type":"PropertyValue","name":"Cutting height","value":"30 mm"},{"@type":"PropertyValue","name":"Cutting direction","value":"right"},{"@type":"PropertyValue","name":"Cutting angle","value":"93°"},{"@type":"PropertyValue","name":"Weight","value":"0.735 kg"}]},{"@type":"FAQPage","mainEntity":[{"@type":"Question","name":"What inserts fit this holder?","acceptedAnswer":{"@type":"Answer","text":"Designed for DCMT 11T3 indexable inserts."}},{"@type":"Question","name":"What is the overall length?","acceptedAnswer":{"@type":"Answer","text":"Overall length is 150 mm."}},{"@type":"Question","name":"What is the ISO designation?","acceptedAnswer":{"@type":"Answer","text":"ISO designation SDJCR 2525."}},{"@type":"Question","name":"What are the shank dimensions?","acceptedAnswer":{"@type":"Answer","text":"Shank width 25 mm and shank height 25 mm."}},{"@type":"Question","name":"What cutting angle does it have?","acceptedAnswer":{"@type":"Answer","text":"Cutting angle 93°; right-hand cutting direction."}},{"@type":"Question","name":"Who is the manufacturer?","acceptedAnswer":{"@type":"Answer","text":"Manufacturer Teknik Makina."}}]},{"@type":"ItemPage","url":"https://metav-shop.de/","dateModified":"2026-04-16T12:00:00+01:00","author":{"@type":"Person","name":"Stephan Bayer","url":"https://www.linkedin.com/in/stephan-bayer/"},"publisher":{"@type":"Organization","name":"Metav Werkzeuge GmbH","url":"https://metav-shop.de","logo":{"@type":"ImageObject","url":"https://files.plytix.com/api/v1.1/file/public_files/pim/assets/57/c3/98/62/6298c3575d155f1bc7e497fd/images/8e/48/c5/69/69c5488eb2b3400ba580741c/logo-metav-1200-675.png","width":1200,"height":675},"address":{"@type":"PostalAddress","streetAddress":"Parkring 45","postalCode":"46446","addressLocality":"Emmerich","addressCountry":"DE"},"telephone":"+49 2822 7131930","email":"info@metav-werkzeuge.com"},"about":[{"@type":"Thing","name":"Turning Holder"},{"@type":"Thing","name":"DCMT 11T3 Compatibility"},{"@type":"Thing","name":"SDJCR 2525 ISO Standard"}],"mentions":[{"@type":"Thing","name":"25x25 mm shank"},{"@type":"Thing","name":"150 mm overall length"},{"@type":"Thing","name":"93° cutting angle"}]}]}

Turning Holder SDJC for DCMT Indexable Inserts by Teknik Makina The Turning Holder is a precision clamping tool designed for DCMT 11T3 indexable inserts, offering a compact 125 mm overall length for stable and accurate lathe operations. For DCMT 11T3 indexable inserts ISO designation SDJCR 2020 Overall Length 125 mm Right-hand Cutting Direction 93° Cutting Angle for Stability Robust Design for Consistent Clamping and Long Service Life The Holder is engineered from durable materials to provide consistent Clamping Force and secure Insert seating, minimising vibration during cutting. Its compact 125 mm Length and reinforced Schneidkopf Width ensure reliable contact between Tool and Workpiece, which translates into improved Surface Finish and prolonged Tool Life. The clear ISO designation SDJCR 2020 simplifies integration into existing tool setups and streamlines workshop logistics. Precision Geometry That Improves Turning Results Thanks to a defined 93° Cutting Angle and a Right-hand Cutting Direction, this tool offers repeatable chipflow and controlled cutting forces for turning tasks. The precise geometry reduces deflection and supports tighter tolerances on turned parts, making the Holder suitable for components that demand dimensional accuracy. Operators will notice reduced rework and more predictable machining cycles, especially when paired with high-quality DCMT Inserts. Practical Use Cases and Who Benefits Most This Turning Holder is aimed at workshops and manufacturers performing medium-duty external turning with indexable Inserts. Ideal for job shops, maintenance departments, and production lines, the tool supports efficient changeover thanks to standardised Insert compatibility. Users looking to improve process stability and reduce setup time will find the Holder particularly valuable, as its proven clamping concept facilitates quick and secure Insert replacement. Compatibility and Integration into Your Tooling System Compatibility with DCMT 11T3 Inserts and the ISO-coded mounting reduce the need for bespoke toolholders and simplify inventory. The Holder’s Width of 20 mm, Height of 20 mm, and Schneidekopf Width of 25 mm match common turret and toolpost setups, allowing straightforward retrofit into many lathe systems. For workshops integrating new tooling, this solution reduces downtime and helps maintain consistent machining parameters across batches. We recommend Teknik Makina’s Turning Holder with SDJCR 2020 geometry for reliable, precision turning — for personalised technical advice or to confirm fitment, METAV Werkzeuge provides comprehensive consultation at info@metav-werkzeuge.com, by phone +49 2822 7131930 or WhatsApp +49 170 2837271 Designation: Turning Holder Brand: Teknik Makina SKU: D226TM Compatible Inserts: DCMT 11T3 ISO Designation: SDJCR 2020 Secondary Designation: K11 Overall Length: 125 mm Width: 20 mm Height: 20 mm Cutting Head Width: 25 mm Cutting Direction: Right Cutting Angle: 93° Weight: 0.404 kg GTIN: 4061905153266 Availability: In Stock Condition: New Manufacturer: Teknik Makina, Nolu Sokak, No 9, Selcuklu, Turkey, eMail: info@teknik-makina.com Responsible Person: Metav Werkzeuge GmbH, Parkring 45, 46446 Emmerich, eMail: info@metav-werkzeuge.com FAQ Which inserts fit the Turning Holder from Teknik Makina? The Turning Holder by Teknik Makina is compatible with DCMT 11T3 indexable inserts; this match ensures proper seating and correct Cutting Angle performance for standard turning operations. Is the Teknik Makina Turning Holder suitable for precision components? Yes, the Teknik Makina Turning Holder with SDJCR 2020 geometry and a 93° Cutting Angle is designed to support consistent machining accuracy for components that require tight tolerances. How do I check if the Turning Holder fits my lathe turret? Measure your turret pocket and compare it with the Holder’s Width (20 mm), Height (20 mm) and Overall Length (125 mm); for detailed compatibility advice, METAV Werkzeuge can assist with application-specific guidance. Can I get technical support for installation of the Turning Holder? METAV Werkzeuge offers expert consultation for the Teknik Makina Turning Holder and can help with installation tips, Insert selection and setup parameters via info@metav-werkzeuge.com or +49 2822 7131930. 125mm SDJCR 2020 Turning Holder for DCMT 11T3, 93° Right - Teknik Makina

Turning Holder – SDJC for DCMT Indexable Inserts by Teknik Makina The Turning Holder is a precision clamping solution designed for DCMT 11T3 indexable inserts, offering stable support and accurate right-hand turning for workshop and industrial applications. Turning Holder for DCMT 11T3 inserts SDJCR 1616 ISO shank for secure seating 100 mm overall length for versatile reach 93° cutting angle for precise right-hand cuts 20 mm cutting head width for stable support Precision clamping that improves cut consistency Built to accommodate DCMT 11T3 indexable inserts, this toolholder delivers predictable cutting behaviour by ensuring a secure seat and minimal play. The SDJCR 1616 ISO geometry provides a standardized interface that simplifies tool changes and keeps insert alignment consistent, which reduces vibration and supports repeatable surface quality. Technicians benefit from improved finish with fewer adjustments during setup. Compact dimensions for reliable tool support With an overall length of 100 mm and a shank profile of 16 mm x 16 mm, the holder offers a compact footprint while maintaining rigidity where it matters. The 20 mm cutting head width is sized to stabilize the insert under load, reducing deflection on longer overhangs. These measured proportions make the component suitable for confined spindle spaces and machining tasks that require both reach and stiffness. Designed for accurate right-hand turning operations This clamping solution is optimized for right-hand cutting tasks, using a 93° cutting angle to combine clearance and robust insert engagement. The geometry helps control chip flow and tool engagement, which in turn supports efficient metal removal and predictable tool life. For shops focusing on turning operations, that targeted design translates into fewer unplanned tool changes and steadier cycle times. Who benefits: workshops, professionals, and precision machinists Production machinists, toolroom specialists and small industrial workshops gain from this holder’s standardized interface and compact design. The Turning Holder is particularly useful where quick insert swaps and dependable alignment are required, such as short-run part production or prototype turning. For operators seeking a balance between accessibility and rigidity, this toolholder supports precise, repeatable results with common DCMT inserts. Choose Teknik Makina’s Turning Holder for dependable, workshop-ready clamping — for personalised advice or to confirm compatibility with your machines, contact METAV Werkzeuge at info@metav-werkzeuge.com or call +49 2822 7131930 Technical Data Bezeichnung: Turning Holder Marke/Hersteller: Teknik Makina SKU: D224TM Compatible Indexable Inserts: DCMT 11T3 Overall Length: 100 mm Weight: 0.204 kg ISO Designation: SDJCR 1616 Secondary Designation: H11 Width: 16 mm Height: 16 mm Cutting Head Width: 20 mm Cutting Height: 25 mm Cutting Direction: right Cutting Angle: 93° GTIN: 4061905153259 Manufacturer: Teknik Makina, Nolu Sokak, No 9, Selcuklu, Türkiye, eMail: info@teknik-makina.com Responsible Person: Metav Werkzeuge GmbH, Parkring 45, 46446 Emmerich, eMail: info@metav-werkzeuge.com FAQ What inserts fit the Turning Holder from Teknik Makina and which insert size is recommended? The Turning Holder from Teknik Makina is designed for DCMT 11T3 indexable inserts; using standard DCMT 11T3 inserts ensures proper seating and expected cutting performance. Is the Teknik Makina Turning Holder suitable for right-hand turning only? Yes, the Teknik Makina Turning Holder is configured for right-hand cutting, utilizing a 93° geometry that supports right-hand turning operations and helps control chip evacuation. How does the SDJCR 1616 designation affect setup and changeover? The SDJCR 1616 ISO designation on this Turning Holder guarantees a standardized shank interface, which simplifies setup and accelerates insert changeover in production environments. Can METAV Werkzeuge advise on whether the Turning Holder fits my machine? If you are unsure whether this Turning Holder by Teknik Makina meets your requirements, METAV Werkzeuge provides expert consultation — contact them at info@metav-werkzeuge.com or call +49 2822 7131930 for detailed guidance. 100mm SDJCR 1616 Turning Holder for DCMT 11T3 Inserts, 93° - Teknik Makina

Turning Holder — SDJC for DCMT Indexable Inserts (Teknik Makina) The Turning Holder is a precision clamping tool designed for use with DCMT 11T3 indexable inserts, offering stable right-hand turning for workshop and production applications. Turning Holder SDJCR 1212 for DCMT 11T3 inserts 110 mm overall length for standard setups Right-hand cutting with 93° cutting angle 12 x 12 mm shank and 16 mm cutting head width Robust construction by Teknik Makina Stable Clamping and Precise Geometry for Reliable Turning The holder features the SDJCR 1212 ISO designation and a compact 12 x 12 mm shank that ensures a secure fit in common tool posts. This precise geometry reduces vibration and runout, which improves surface finish and extends Insert life. For users unfamiliar with toolholder codes: SDJCR 1212 indicates the holder style and shank dimensions, while the matching DCMT 11T3 inserts are the removable cutting tips that allow fast replacement without regrinding. Designed for Production Use and Workshop Flexibility With an overall length of 110 mm and a 16 mm cutting head width, this holder suits a broad range of turning operations from finishing to light roughing. The right-hand cutting orientation and 93° cutting angle make it particularly effective for conventional turning tasks where consistent chip flow and tool clearance are required. Operators benefit from predictable cutting behaviour and simplified setup when integrating the holder into existing tooling systems. Clear Benefits for Machinists and Small Series Manufacturers By combining a standardized ISO mount with robust manufacturing by Teknik Makina, this toolholder offers repeatable positioning and quick insert changes, reducing downtime during tool swaps. The stable clamping reduces insert wear, which lowers per-part tooling costs over medium production runs. For shops transitioning from brazed tools to indexable systems, this holder provides an accessible step with familiar handling and fast maintenance. Who Should Choose This Holder and How It Improves Workflow This Turning Holder is aimed at professional machinists, job shops and maintenance departments that rely on modular tooling for turnaround and versatility. Its compact shank and standardized interface make it suitable for limited-space setups and retrofit projects. When paired with correctly specified DCMT inserts, users achieve consistent surface quality and predictable tool life, supporting tighter production tolerances and fewer reworks. We recommend the Teknik Makina Turning Holder SDJCR 1212 for precision turning applications—contact METAV Werkzeuge for personalised advice and technical support via eMail info@metav-werkzeuge.com, telephone +49 2822 7131930 or WhatsApp +49 170 2837271. Technical Information Designation: Klemmhalter Brand: Teknik Makina SKU: D222TM Suitable Inserts: DCMT 11T3 ISO Designation: SDJCR 1212 Secondary Designation: J11 Overall Length: 110 mm Weight: 0.132 kg Shank Width: 12 mm Shank Height: 12 mm Cutting Head Width: 16 mm Cutting Height: 20 mm Cutting Direction: Right Cutting Angle: 93° GTIN: 4061905153242 Manufacturer: Teknik Makina, Nolu Sokak, No 9, Selcuklu, Türkei, eMail: info@teknik-makina.com Responsible Person: Metav Werkzeuge GmbH, Parkring 45, 46446 Emmerich, eMail: info@metav-werkzeuge.com FAQ What inserts fit the Turning Holder from Teknik Makina? The Teknik Makina Turning Holder is designed for DCMT 11T3 indexable inserts; using these recommended inserts ensures correct seating and optimal cutting geometry with the SDJCR 1212 mounting. Can the SDJCR 1212 holder be used for finish turning? Yes, the SDJCR 1212 Turning Holder from Teknik Makina, combined with appropriate DCMT inserts and cutting parameters, provides the stability and surface finish quality required for many finishing operations. Is the mounting size compatible with standard tool posts? The Teknik Makina Turning Holder uses a 12 x 12 mm shank and ISO-style configuration, which matches common tool post systems; this allows straightforward integration into typical lathe setups. Who can help determine the right insert and parameters for this Turning Holder? METAV Werkzeuge offers expert consultation for the Teknik Makina Turning Holder and can advise on insert selection, cutting speeds and feeds; contact them at info@metav-werkzeuge.com or +49 2822 7131930. 110mm SDJCR 1212 Turning Holder for DCMT 11T3, 93° Right - Teknik Makina

Turning Holder SDJC for DCMT Indexable Inserts by Teknik Makina The Turning Holder SDJC for DCMT Indexable Inserts is a flat, low-profile clamp designed for secure and precise left-hand turning with DCMT 11T3 inserts in metalworking lathes. SDJC design for DCMT 11T3 inserts Flat version for low-profile turning 100 mm total length for stable support 16 x 16 mm shank for standard tool posts Left-hand cutting with 93° cutting angle Robust support for precise turning and repeatability The SDJC Turning Holder delivers stable clamping and consistent tool positioning thanks to its 100 mm Total Length and compact 16 x 16 mm cross-section. This rigidity reduces vibration and improves Surface Finish on turned components, which translates into fewer reworks and higher first-pass yield. The holder's flat profile makes it particularly suitable for operations in confined tool zones where clearance is limited. Quick insert changes and economical cutting Designed specifically for DCMT 11T3 indexable inserts, the Turning Holder enables fast insert replacement and consistent cutting geometry. DCMT inserts are triangular, reversible carbide inserts that allow multiple cutting edges per insert; this reduces tooling costs and maintenance intervals. For users unfamiliar with indexable tooling: an indexable insert is a replaceable cutting tip that is clamped into the holder, so only the insert—not the entire tool—is renewed when worn. Built for left-hand cutting and easy mounting This toolholder is configured for left-hand cutting with a 93° cutting angle, making it suitable for turning directions that demand a specific tool orientation. Assembly and service are straightforward: the clamp uses a Torx T15 key and an M3.5x8.5 Torx screw for the insert clamping, while the base plate references TA030 with an M5 fixing screw. These standardized fasteners facilitate quick setup and reduce machine downtime during tool changes. Who benefits and typical applications Workshop machinists, small-series manufacturers, and maintenance departments benefit from this flat SDJC design when working on shafts, shoulders or profiles in restricted-envelope setups. The Turning Holder is aimed at professionals seeking dependable clamping for medium-duty turning tasks and rapid insert swaps. Its combination of compact dimensions and standardized interface supports predictable cycle times and easier inventory management of consumables. Strong recommendation: choose the Teknik Makina Turning Holder SDJC for reliable clamping and improved machining consistency — for technical guidance METAV Werkzeuge offers expert support via info@metav-werkzeuge.com or by phone at +49 2822 7131930, WhatsApp +49 170 2837271. Bezeichnung: Klemmhalter Marke: Teknik Makina SKU: D157TM Alternative designation: SDJC for DCMT Indexable Inserts English product name: Turning Holder Eclass: 21181004 Suitable inserts: DCMT 11T3 Total length: 100 mm Holder ISO designation: SDJCL 1616 Shank width: 16 mm Shank height: 16 mm Cutting head width: 16 mm Cutting height: 25 mm Cutting direction: left Cutting angle: 93° Torx key: T15 Torx screw: M3,5x8,5 U plate: TA030 U plate screw: M5 Drill rod designation: H11-F Manufacturer: Teknik Makina, Nolu Sokak, No 9, Selcuklu, Turkey, eMail: info@teknik-makina.com Responsible Person: Metav Werkzeuge GmbH, Parkring 45, 46446 Emmerich, eMail: info@metav-werkzeuge.com FAQ What inserts fit the Turning Holder from Teknik Makina and which sizes are supported? The Turning Holder from Teknik Makina is designed for DCMT 11T3 indexable inserts; this means standard DCMT triangular inserts fit securely and provide multiple cutting edges for economical use. Can the SDJC Turning Holder be used in tight toolpost arrangements? Yes, the flat SDJC Turning Holder by Teknik Makina is a low-profile variant intended for limited-clearance setups, offering a compact 16 x 16 mm shank that suits many standard tool posts. How is an insert secured in the Turning Holder SDJC and what tools are required? Inserts are clamped using the supplied Torx fastener system: the Turning Holder uses a Torx T15 key and M3.5x8.5 Torx screw for secure and repeatable fixation of DCMT inserts. Who can help if I need assembly advice for my Teknik Makina Turning Holder? METAV Werkzeuge provides competent consultation for the Teknik Makina Turning Holder; contact their team at info@metav-werkzeuge.com or call +49 2822 7131930 for technical support and application guidance. {"@context":"https://schema.org","@graph":[{"@type":"Product","@id":"#D157TM","sku":"D157TM","mpn":"D157TM","gtin13":"","name":"Turning Holder SDJC for DCMT Indexable Inserts, Flat, Left, 93° - Teknik Makina","description":"16mm SDJC turning holder for DCMT 11T3 indexable inserts; flat design, left cutting direction, 93° cutting angle, 100mm overall length, 0.18 kg.","image":["https://files.plytix.com/api/v1.1/file/public_files/pim/assets/57/c3/98/62/6298c3575d155f1bc7e497fd/images/59/40/bb/66/66bb40598ce61d4fe144ccc2/d154tm-main.png","https://files.plytix.com/api/v1.1/file/public_files/pim/assets/57/c3/98/62/6298c3575d155f1bc7e497fd/images/59/40/bb/66/66bb40598ce61d4fe144ccc1/d154tm-technische-zeichnung.png","https://files.plytix.com/api/v1.1/file/public_files/pim/assets/57/c3/98/62/6298c3575d155f1bc7e497fd/images/58/40/bb/66/66bb4058849b5d97e5677066/d154tm-artikelliste.png"],"additionalProperty":[{"@type":"PropertyValue","name":"Type","value":"SDJC"},{"@type":"PropertyValue","name":"Compatible Inserts","value":"DCMT 11T3"},{"@type":"PropertyValue","name":"Design","value":"Flat"},{"@type":"PropertyValue","name":"Cutting Direction","value":"Left"},{"@type":"PropertyValue","name":"Cutting Angle","value":"93°"},{"@type":"PropertyValue","name":"Overall Length","value":"100 mm"},{"@type":"PropertyValue","name":"Width","value":"16 mm"},{"@type":"PropertyValue","name":"Height","value":"16 mm"},{"@type":"PropertyValue","name":"Cutting Head Width","value":"16 mm"},{"@type":"PropertyValue","name":"Cutting Height","value":"25 mm"},{"@type":"PropertyValue","name":"Weight","value":"0.18 kg"},{"@type":"PropertyValue","name":"Clamping Holder ISO","value":"SDJCL 1616"},{"@type":"PropertyValue","name":"Shank Designation","value":"H11-F"},{"@type":"PropertyValue","name":"Torx Key","value":"T15"},{"@type":"PropertyValue","name":"Torx Screw","value":"M3.5x8.5"},{"@type":"PropertyValue","name":"U Plate","value":"TA030"},{"@type":"PropertyValue","name":"U Plate Screw","value":"M5"},{"@type":"PropertyValue","name":"Net Price","value":"35"}]},{"@type":"FAQPage","mainEntity":[{"@type":"Question","name":"Which inserts fit this holder?","acceptedAnswer":{"@type":"Answer","text":"Compatible with DCMT 11T3 indexable inserts."}},{"@type":"Question","name":"What is the cutting direction?","acceptedAnswer":{"@type":"Answer","text":"Left cutting direction (left hand)."}},{"@type":"Question","name":"What is the cutting angle?","acceptedAnswer":{"@type":"Answer","text":"93° cutting angle for versatile turning operations."}},{"@type":"Question","name":"What are the main dimensions?","acceptedAnswer":{"@type":"Answer","text":"16 mm width and height, 100 mm overall length; cutting head width 16 mm and cutting height 25 mm."}},{"@type":"Question","name":"Who is the manufacturer?","acceptedAnswer":{"@type":"Answer","text":"Teknik Makina."}}]},{"@type":"ItemPage","url":"https://metav-shop.de","dateModified":"2026-03-31T12:00:00+01:00","author":{"@type":"Person","name":"Stephan Bayer","url":"https://www.linkedin.com/in/stephan-bayer/"},"publisher":{"@type":"Organization","name":"Metav Werkzeuge GmbH","url":"https://metav-shop.de","logo":{"@type":"ImageObject","url":"https://files.plytix.com/api/v1.1/file/public_files/pim/assets/57/c3/98/62/6298c3575d155f1bc7e497fd/images/8e/48/c5/69/69c5488eb2b3400ba580741c/logo-metav-1200-675.png","width":1200,"height":675},"address":{"@type":"PostalAddress","streetAddress":"Parkring 45","postalCode":"46446","addressLocality":"Emmerich","addressCountry":"DE"},"telephone":"+49 2822 7131930","email":"info@metav-werkzeuge.com"},"about":[{"@type":"Thing","name":"Turning Holder SDJC Series"},{"@type":"Thing","name":"Allround Clamping Holders"},{"@type":"Thing","name":"Suitable for DCMT Inserts"}],"mentions":[{"@type":"Thing","name":"SDJCL 1616"},{"@type":"Thing","name":"TA030 U Plate"},{"@type":"Thing","name":"Torx T15"}]}]}

Die Kombination aus Linksschneidung, kompakter Breite 12 mm und der Gesamtlänge 110 mm sorgt für stabile, reproduzierbare Schnitte bei Serienbearbeitung; nutzen Sie die Wirtschaftlichkeit und Verlässlichkeit dieses Klemmhalters direkt über Metav Werkzeuge oder fragen Sie unsere Beratung bei Bedarf an. SDJCL 1212 SDJC Toolholder for DCMT Indexable Inserts Der SDJCL 1212 SDJC Toolholder bietet eine stabile Linksschneidung für Drehbearbeitungen mit DCMT Einsätzen und eignet sich für präzise, wiederholbare Schnitte in Serienfertigung. Compatible with DCMT 11T3 inserts Compact 12 mm Width and 12 mm Height Left-hand Cutting orientation for specific turning operations Robust Torx fixing with T15 key Overall Length 110 mm for extended reach Höhere Prozessstabilität durch präzise Klemmung Der Toolholder wurde für wiederholbare Spannvorgänge entwickelt und bietet dank der Klemmfunktion hohe Stabilität bei Schnittkräften. Die Kombination aus 12 mm Breite und 12 mm Höhe reduziert Schwingungen und ermöglicht saubere Spanabfuhr, wodurch die Oberflächenqualität verbessert wird. Anwender profitieren von konstanter Bearbeitungsleistung bei mittleren bis grossen Losgrößen. Kompatibilität und Montagefreundlichkeit für den Werkstattalltag Dieser Halter ist ausgelegt für DCMT 11T3 Wendeplatten und wird mit einer U-Platte TA030 sowie einer M5 U-Platten-Schraube montiert. Die Torx-Schraube (M3,5x8,5) und der mitgelistete T15 Torx-Schlüssel sorgen für schnelle und sichere Wechselvorgänge, wodurch Rüstzeiten minimiert und die Maschinenlaufzeit erhöht werden. Technische Präzision für sichere Schneidgeometrie Mit einem Schnittwinkel von 93° und einer Schneidenhöhe von 20 mm unterstützt der Halter exakte Spanführung und definiertes Eingriffsverhalten. Die Linksschneidung ist speziell für Anwendungen konzipiert, die eine bestimmte Vorschubrichtung erfordern, und trägt so zu reproduzierbaren Ergebnissen bei komplexen Schnitten bei. Zielgruppe und Einsatzbereiche Dieser Toolholder richtet sich an Drehereien, Feinmechaniker und den produzierenden Metallbau, die hohe Stabilität bei Indexplatten-Einsätzen erwarten. Er eignet sich besonders für Anwender, die standardisierte Inserts verwenden und schnellen Wechsel sowie geringe Schwingungsneigung benötigen. Empfehlung: Entscheiden Sie sich für den SDJCL 1212 von Teknik Makina als zuverlässige Ergänzung Ihrer Fertigungswerkzeuge und bestellen Sie direkt bei Metav Werkzeuge in Emmerich für sicheren Versand und kompetente Beratung. Kontakt: info@metav-werkzeuge.com / +49 2822 7131930 Product Features Artikelnummer: D156TM Marke: Teknik Makina Bezeichnung: Klemmhalter SDJC for DCMT Indexable Inserts Facts Gesamtlänge: 110 mm Klemmhalter Breite: 12 mm Klemmhalter Höhe: 12 mm Schneidenkopf Breite: 12 mm Schneidenhöhe: 20 mm Gewicht: 0.13 kg Schnittwinkel: 93° Schnittrichtung: left Besonderheiten Fur Wendeplatten: DCMT 11T3 (Indexable Carbide Insert Type) Klemmhalter Bezeichnung ISO: SDJCL 1212 U Platte: TA030 U Platte Schraube: M5 Torx Schraube: M3,5x8,5 — Torx Fixing for Quick Insert Clamping Torx Schlüssel: T15 — Required Tool for Screw Tightening FAQ Ist der SDJCL 1212 mit DCMT 11T3 Einsätzen kompatibel? Ja, der SDJCL 1212 SDJC Toolholder von Teknik Makina ist ausgelegt für DCMT 11T3 Einsätze und bietet die passende Aufnahme sowie die erforderliche Klemmung für sicheren Halt. Welche Schrauben und Werkzeuge werden für die Montage benötigt? Für die Montage werden die M5 U-Platten-Schraube und die Torx-Schraube M3,5x8,5 verwendet; zum Festziehen ist ein T15 Torx-Schlüssel geeignet. Eignet sich der Halter für Linksschneidung? Der Halter ist für Linksschneidung konzipiert; die Schnittrichtung ist als left angegeben, was ihn für entsprechende Drehanwendungen prädestiniert. Welche Abmessungen sind besonders relevant für den Einsatz in meiner Drehmaschine? Wesentliche Werte sind die Breite 12 mm, Höhe 12 mm, Schneidenhöhe 20 mm und die Gesamtlänge 110 mm; diese Angaben helfen bei der Auswahl passender Werkzeugaufnahmen.

Combine secure clamping, compact 16 mm design and right-hand cutting geometry for reliable, repeatable turning results; the secure Torx clamp and compatibility with DCMT 11T3 inserts reduce setup time and tool changes. Order via Metav Werkzeuge or request technical advice from our specialists for seamless integration on the shop floor. SDJCR 1616 Clamp Holder — SDJC for DCMT Indexable Inserts The SDJCR 1616 Clamp Holder is a right-hand, flat-profile toolholder engineered for use with DCMT 11T3 indexable inserts in precision turning applications. Compatible with DCMT 11T3 inserts 16 mm toolholder width for compact set-ups Right-hand cutting geometry, 93° cutting angle Torx screw M3.5x8.5 with T15 key for secure clamping U-Plate TA030 and M5 retaining screw included Maximum rigidity with a compact footprint Built to offer high clamping force in a narrow space, this clamp holder combines a 16 mm Wide Shank and a low-profile Cutting Head to minimise interference on complex parts. The compact dimensions permit closer tool-to-workpiece positioning, which helps to reduce vibration and improves surface finish. By focusing on mechanical stiffness rather than oversized mass, the design supports stable machining cycles and consistent dimensional results. Faster changeovers and reliable insert retention The clamping system relies on a Torx M3.5x8.5 screw operated with a T15 key for reproducible torque and secure insert retention. This arrangement enables quicker insert replacement while maintaining the correct seat and angle, reducing downtime between operations. The flat SDJC configuration supports straightforward indexing of DCMT 11T3 inserts, keeping the process efficient and predictable in batch and one-off production. Precision geometry for controlled cutting forces A cutting angle of 93° and right-hand cut direction offer balanced force distribution during turning, which reduces deflection on slender workpieces. The toolholder is specified as SDJCR 1616, providing a standardised interface for fixtures and post designs. With the Shank designation H11-F available for mounting considerations, the holder aligns with common lathe turrets and tooling blocks to simplify integration. Practical mounting and assembly features The holder is supplied for use with the TA030 U-Plate and an M5 U-Plate Screw for secure attachment to Tool Blocks. The Torx Screw and Torx Key combination ensures consistent clamping torque and easy maintenance. These details shorten assembly time and support repeatable set-ups across multiple machines, making the component a pragmatic choice for both mixed-production cells and dedicated turning stations. Strong recommendation: choose the Teknik Makina SDJCR 1616 Clamp Holder for dependable insert clamping and compact toolroom integration — contact Metav Werkzeuge in Emmerich for supply and application support via info@metav-werkzeuge.com or +49 2822 7131930 Product Characteristics Article number: D458TM Brand: Teknik Makina Designation: SDJCR 1616 SDJC for DCMT Indexable Inserts Facts Holder Width: 16 mm Holder Height: 16 mm Cutting Head Width: 16 mm Overall Length: 100 mm Cutting Angle: 93° Weight: 0.18 kg Features Compatible Insert: DCMT 11T3 (indexable turning insert) Torx Screw: M3.5x8.5 Torx Key: T15 (for secure torque) U-Plate: TA030 U-Plate Screw: M5 Shank Designation: H11-F Cutting Direction: Right ISO Designation: SDJCR 1616 FAQ What inserts fit this clamp holder? The SDJCR 1616 Clamp Holder from Teknik Makina (SKU D458TM) is designed for DCMT 11T3 indexable inserts, providing a stable seat and correct cutting geometry for standard turning tasks. Is the clamping screw type specified for consistent torque? Yes, the clamp uses a Torx Screw M3.5x8.5 secured with a T15 Torx Key; the combination in the SDJCR 1616 design ensures reproducible clamping and easy maintenance. Can this holder be mounted on common turret systems? The SDJCR 1616 (Teknik Makina, D458TM) features a compact 16 mm Shank and Shank designation H11-F, making it suitable for many turret and tool block interfaces where a flat SDJC holder is required. What is the cutting orientation and angle of the holder? The holder is configured for a right-hand cutting direction with a 93° cutting angle, optimised to balance cutting forces and limit deflection on longer workpieces. Does the product include the necessary U-Plate parts? The technical specification lists the compatible U-Plate as TA030 and the U-Plate Screw as M5; these details support correct mounting and should be checked against your machine’s fixture requirements. Manufacturer: Teknik Makina, Nolu Sokak, No 9, Selcuklu, Türkiye, eMail: info@teknik-makina.com / Verantwortlich: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Turning Holder SDJCR 1212 (for DCMT 11T3 indexable inserts) A robust Turning Holder engineered for precision external turning and secure clamping of DCMT 11T3 indexable inserts. SDJCR 1212 compatible with DCMT 11T3 110 mm Overall Length for improved accessibility 12×12 mm Shank for compact toolposts 93° Cutting Angle for stable engagement Right-hand Cutting orientation Precise Clamping for Improved Surface Finish The Turning Holder SDJCR 1212 is designed to secure DCMT 11T3 Inserts with consistent Clamping force, which reduces vibration and improves Surface Finish during turning operations. Its defined geometry and stable insert seat enable reliable Cutting engagement and help maintain tool life by preventing micro-movement at the Insert interface. This results in better Accuracy on finished parts and fewer rework cycles, making the toolholder suitable for high-precision machining tasks. Compact Dimensions for Confined Setups With a Shank of 12×12 mm and an Overall Length of 110 mm, this toolholder is tailored for tight Turret configurations and close-proximity turning where space is limited. The compact profile allows for easier access to narrow workpieces while preserving necessary clearance for tooling, operators and fixtures. This compact design supports efficient machine layout planning and minimizes the need for frequent repositioning, particularly in batch production and repair jobs. Stable Geometry and Repeatable Performance Built to ensure Repeatability, the holder’s 93° Cutting Angle and precise seat alignment deliver reproducible cutting conditions across repeated setups. The simple but robust construction reduces setup time and keeps process variables low, which benefits shops that prioritise consistent tolerances. Combined with DCMT 11T3 Inserts, this holder provides a stable platform for turning, facing and light profiling operations in general engineering and maintenance contexts. Application Focus and Intended Users Designed by Teknik Makina, this turning tool is aimed at machinists, job shops and maintenance departments that require a dependable and compact solution for indexable Insert turning. The SDJCR 1212 proves particularly effective for external turning of shafts, shoulders and small-diameter features where controlled Chip formation and tool access are critical. For complex requirements or integration into a specific machine setup, METAV Werkzeuge offers expert technical guidance to match tooling to the task. Strong recommendation: choose the technical reliability of Teknik Makina’s Turning Holder SDJCR 1212 for precision turning — for personalised advice and ordering, contact METAV Werkzeuge by email at info@metav-werkzeuge.com, by phone at +49 2822 7131930 or via WhatsApp at +49 170 2837271 Bezeichnung: Turning Holder Marke: Teknik Makina SKU: D457TM Compatible Inserts: DCMT 11T3 ISO Designation: SDJCR 1212 Alternate Designation: J11-F Overall Length: 110 mm Shank Width: 12 mm Shank Height: 12 mm Cutting Head Width: 12 mm Cutting Angle: 93° Cutting Direction: Right Weight: 0.134 kg GTIN: 4061905153471 Availability: in Stock Condition: new Eclass: 21181004 Manufacturer: Teknik Makina, Nolu Sokak, No 9, Selcuklu, Turkey, eMail: info@teknik-makina.com Responsible Person: Metav Werkzeuge GmbH, Parkring 45, 46446 Emmerich, eMail: info@metav-werkzeuge.com FAQ What Inserts fit the Turning Holder from Teknik Makina? The Teknik Makina Turning Holder SDJCR 1212 is designed to accept DCMT 11T3 indexable inserts, providing a secure seat and correct rake alignment for typical external turning operations. Is the SDJCR 1212 suitable for use in compact Turrets? Yes, the SDJCR 1212 Turning Holder from Teknik Makina features a 12×12 mm Shank and a compact 110 mm Overall Length, making it well suited for confined Turret setups where clearance is limited. Can METAV Werkzeuge help with selection and compatibility? METAV Werkzeuge supports customers with technical advice for the Teknik Makina Turning Holder SDJCR 1212 and can assist in confirming compatibility with specific lathes or Insert grades via email or phone. What cutting direction does the holder support? The Teknik Makina SDJCR 1212 Turning Holder is configured for Right-hand Cutting direction with a 93° Cutting Angle to ensure stable engagement and predictable Chip formation. 93° SDJCR 1212 Turning Holder for DCMT 11T3 Inserts, 110 mm - Teknik Makina

Turning Holder (SDHCL 2525) for DCMT 11T3 Inserts — Teknik Makina The Turning Holder is a robust toolholder designed to securely clamp DCMT 11T3 indexable inserts for precise left-hand turning operations in metalworking. SDHCL 2525 for DCMT 11T3 inserts 150 mm overall length for deep reach 25 mm shank width and height 107.5° cutting angle for stable cuts Left-hand cutting direction Consistent Rigidity and Repeatability for Accurate Turning The Turning Holder delivers Rigidity that reduces vibration and improves Surface Finish when machining a variety of materials. The clamping concept ensures repeatable insert positioning so that tool paths remain stable cycle after cycle. For users seeking measurable improvements in tool life and part quality, this Holder provides a straightforward way to raise Process Reliability without changing machine settings. Clear Dimensions and Direct Compatibility to Save Setup Time With an Overall Length of 150 mm and a Shank of 25 mm x 25 mm, the holder fits common toolpost mounts and enables access to deeper workpieces. The Schneidkopf Width of 32 mm and ISO designation SDHCL 2525 make it compatible with DCMT 11T3 indexable inserts, simplifying procurement and changeover. For those new to insert coding: DCMT denotes a diamond-shaped insert with specific rake and clearance characteristics, chosen here for universal turning tasks. Geometry Designed for Efficient Cutting and Chip Control The Holder’s 107.5° Cutting Angle and Left-Hand cutting direction concentrate cutting forces to the clamped Insert, promoting stable cutting and predictable chip flow. This geometry helps reduce deflection during interrupted cuts and supports consistent surface tolerance. Operators benefit from fewer reworks and more predictable tool-change intervals, improving overall Shop Floor Throughput with minimal process adjustment. Who Benefits and Where to Get Expert Advice Precision Workshops, Job Shops and Maintenance Departments that require reliable, repeatable turning operations will find this Holder especially useful. Installation and selection are straightforward, yet technical choices such as Insert Grade or Cutting Conditions can impact results. METAV Werkzeuge offers extensive and competent advice for tool selection and application support; expert help is available if further technical data or compatibility checks are needed. We recommend Teknik Makina’s Turning Holder SDHCL 2525 for reliable, precision turning — for personalised advice contact METAV Werkzeuge at info@metav-werkzeuge.com or call +49 2822 7131930. Designation: Turning Holder (Klemmhalter) Brand: Teknik Makina SKU: D352TM Compatible Inserts: DCMT 11T3 ISO Designation: SDHCL 2525 Overall Length: 150 mm Shank Width: 25 mm Shank Height: 25 mm Cutting Head Width: 32 mm Cutting Angle: 107.5° Cutting Direction: Left Weight: 0.738 kg GTIN: 4061905153518 Availability: In Stock Condition: New Manufacturer: Teknik Makina, Nolu Sokak, No 9, Selcuklu, Turkey, eMail: info@teknik-makina.com Responsible Person: Metav Werkzeuge GmbH, Parkring 45, 46446 Emmerich, eMail: info@metav-werkzeuge.com FAQ What inserts fit the Turning Holder from Teknik Makina and which designation should I order? The Turning Holder from Teknik Makina is designed for DCMT 11T3 indexable inserts; order inserts matching the DCMT 11T3 geometry to ensure correct fit and cutting performance with the SDHCL 2525 clamp. Can the Turning Holder SDHCL 2525 be mounted on my existing toolpost? The SDHCL 2525 Turning Holder has a Shank of 25 mm x 25 mm and an Overall Length of 150 mm, so it fits standard toolpost systems that accept a 25 mm shank; confirm your toolpost clamping dimensions or contact METAV Werkzeuge for compatibility checks. How does the 107.5° cutting angle affect machining with the Teknik Makina Turning Holder? The 107.5° cutting angle concentrates cutting forces to the Insert and Holder interface, improving stability and chip control during turning; this leads to more consistent surface quality and extended Insert life under comparable cutting conditions. 150mm SDHCL 2525 Turning Holder for DCMT 11T3 Indexable Inserts, 107.5° - Teknik Makina

Technical Information: Order Number: S072TM Item: T-Grove Holder usable with DCMT 11T3 Indexable Inserts Brand: Teknik Makina Numbers and Data: Diameter: 63mm Cutting Edges: 4 Weight: 0.536kg Total length: 120mm Manufacturer Teknik Makina, Nolu Sokak, No 9, Selcuklu, Turkey, eMail: info@teknik-makina.com Responsible for Europe Metav Werkzeuge GmbH, Parkring 45, 46446 Emmerich, Germany, eMail: info@metav-werkzeuge.com

Product Technical Details: Order Number: D442TM Item: Turning Holder usable with DCMT 11T3 Indexable Inserts Brand: Teknik Makina ISO Code: SDACR 1616 H11-F Numbers and Data: Weight: 0.2kg Total length: 100mm Additional Informattion Cutting Direction: rechts Manufacturer Teknik Makina, Nolu Sokak, No 9, Selcuklu, Turkey, eMail: info@teknik-makina.com Responsible for Europe Metav Werkzeuge GmbH, Parkring 45, 46446 Emmerich, Germany, eMail: info@metav-werkzeuge.com

Turning Holder SVJCR 2020 — Precision Turning Holder for DCMT 11T3 Inserts The Turning Holder SVJCR 2020 is a right-hand toolholder engineered for stable external turning with DCMT 11T3 indexable inserts in industrial and workshop environments. Turning Holder SVJCR 2020 for DCMT 11T3 inserts 150 mm overall length for stable tool engagement Internal coolant for improved chip evacuation 93° cutting angle for precise turning operations Right-hand configuration with 32 mm head width Consistent Precision and Stable Cutting Performance This toolholder delivers precision by combining a robust 150 mm overall length with a 93° cutting angle that supports predictable chip flow and reduced vibration. Designed for demanding turning tasks, the holder’s geometry ensures secure seating of DCMT 11T3 inserts and repeatable tool positioning, which translates into consistent part quality and longer insert life. Efficient Chip Control and Cooling for Longer Tool Life Equipped with internal coolant, the holder channels cutting fluid directly to the cutting zone to improve chip evacuation and heat dissipation. This targeted cooling reduces thermal load on the insert and workpiece, helping to maintain cutting-edge integrity and lowering the frequency of tool changes, which benefits productivity in serial turning operations. Compact Head Design for Versatile Machine Access With a 32 mm Schneidekopf Breite (cutting head width) and compact 25 mm body dimensions, the holder offers access to tighter workspaces without sacrificing rigidity. The low-profile design supports effective machining in setups where space is limited, making it a practical choice for workshops that handle a variety of part geometries and fixture arrangements. Built for Workshop Reliability and Easy Maintenance Manufactured by Teknik Makina, this holder follows the ISO designation SVJCR 2020, ensuring compatibility with standard clamping procedures and replacement inserts. Assembly and maintenance are straightforward, with Torx fixing (M2,5x6,5) and T8 key compatibility, enabling quick insert changes and reducing machine downtime. For reliable, precision turning choose the Teknik Makina Turning Holder SVJCR 2020 — for technical questions or ordering assistance contact METAV Werkzeuge at info@metav-werkzeuge.com or call +49 2822 7131930. Designation: Turning Holder (Klemmhalter) Brand: Teknik Makina SKU: AP521TM Compatible Inserts: DCMT 11T3 Alternative designation: SVJC for VCMT Indexable Inserts (Bezeichnung 2: K11-IK) ISO designation: SVJCR 2020 Overall Length: 150 mm Width: 25 mm Height: 25 mm Cutting Head Width: 32 mm Cutting Edge Height: 35 mm Cutting Direction: Right Cutting Angle: 93° Internal Coolant: Yes Weight: 0.735 kg Torx Key: T8 Torx Screw: M2,5x6,5 Condition: New Availability: In Stock GTIN: 4061905052491 Manufacturer: Teknik Makina, Nolu Sokak, No 9, Selcuklu, Turkey, eMail: info@teknik-makina.com Responsible Person: Metav Werkzeuge GmbH, Parkring 45, 46446 Emmerich, eMail: info@metav-werkzeuge.com FAQ What inserts fit the Turning Holder SVJCR 2020 from Teknik Makina? The Turning Holder SVJCR 2020 by Teknik Makina is designed to accept DCMT 11T3 indexable inserts; this combination ensures a secure fit and optimal cutting geometry for external turning tasks. Does the Teknik Makina Turning Holder SVJCR 2020 support coolant-through operation? Yes, the Teknik Makina Turning Holder SVJCR 2020 features internal coolant capability to direct fluid to the cutting zone and improve chip evacuation and thermal control. What are the key dimensions to consider when selecting this Turning Holder? Important dimensions include a 150 mm overall length, 25 mm body width and height, and a 32 mm cutting head width; these values help determine fit and accessibility in your machine setup. Is the SVJCR 2020 easy to maintain in a production environment? The SVJCR 2020 Turning Holder from Teknik Makina uses standard Torx fixing (M2,5x6,5) and a T8 key, allowing rapid insert changes and straightforward maintenance to minimize machine downtime. Who can assist if I need further technical advice about the Turning Holder SVJCR 2020? METAV Werkzeuge provides comprehensive and competent consultation; contact info@metav-werkzeuge.com, call +49 2822 7131930, or WhatsApp +49 170 2837271 for tailored support and additional technical details. {"@context":"https://schema.org","@graph":[{"@type":"Product","@id":"#AP521TM","sku":"AP521TM","mpn":"AP521TM","gtin13":"4061905052491","name":"150mm SVJCR 2020 93° Turning Holder for DCMT 11T3","description":"Turning holder SVJCR 2020 for DCMT 11T3 indexable inserts; 150 mm overall length, internal coolant, 93° cutting angle, right-hand; robust clamping design by Teknik Makina.","image":["https://files.plytix.com/api/v1.1/file/public_files/pim/assets/57/c3/98/62/6298c3575d155f1bc7e497fd/images/08/8d/e2/62/62e28d080f56dbb4de4e128a/ap520.jpg"],"additionalProperty":[{"@type":"PropertyValue","name":"ISO Designation","value":"SVJCR 2020"},{"@type":"PropertyValue","name":"Compatible Inserts","value":"DCMT 11T3"},{"@type":"PropertyValue","name":"Overall Length","value":"150 mm"},{"@type":"PropertyValue","name":"Weight","value":"0.735 kg"},{"@type":"PropertyValue","name":"Cutting Angle","value":"93°"},{"@type":"PropertyValue","name":"Coolant","value":"internal coolant"},{"@type":"PropertyValue","name":"Direction","value":"right"},{"@type":"PropertyValue","name":"Head Width","value":"32 mm"},{"@type":"PropertyValue","name":"Body Width","value":"25 mm"},{"@type":"PropertyValue","name":"Body Height","value":"25 mm"},{"@type":"PropertyValue","name":"Insert Holder Code","value":"K11-IK"},{"@type":"PropertyValue","name":"Torx Key","value":"T8"},{"@type":"PropertyValue","name":"Torx Screw","value":"M2.5x6.5"}]},{"@type":"FAQPage","mainEntity":[{"@type":"Question","name":"What inserts fit this holder?","acceptedAnswer":{"@type":"Answer","text":"Designed for DCMT 11T3 indexable inserts."}},{"@type":"Question","name":"What is the overall length?","acceptedAnswer":{"@type":"Answer","text":"Overall length is 150 mm."}},{"@type":"Question","name":"Does it have internal coolant?","acceptedAnswer":{"@type":"Answer","text":"Yes, the holder features internal coolant."}},{"@type":"Question","name":"What is the cutting angle?","acceptedAnswer":{"@type":"Answer","text":"Cutting angle is 93 degrees."}},{"@type":"Question","name":"Is this right- or left-hand?","acceptedAnswer":{"@type":"Answer","text":"This is a right-hand turning holder."}},{"@type":"Question","name":"Who is the manufacturer?","acceptedAnswer":{"@type":"Answer","text":"Manufacturer is Teknik Makina."}}]},{"@type":"ItemPage","url":"https://metav-shop.de/","dateModified":"2026-03-31T12:00:00+01:00","author":{"@type":"Person","name":"Stephan Bayer","url":"https://www.linkedin.com/in/stephan-bayer/"},"publisher":{"@type":"Organization","name":"Metav Werkzeuge GmbH","url":"https://metav-shop.de","logo":{"@type":"ImageObject","url":"https://files.plytix.com/api/v1.1/file/public_files/pim/assets/57/c3/98/62/6298c3575d155f1bc7e497fd/images/8e/48/c5/69/69c5488eb2b3400ba580741c/logo-metav-1200-675.png","width":1200,"height":675},"address":{"@type":"PostalAddress","streetAddress":"Parkring 45","postalCode":"46446","addressLocality":"Emmerich","addressCountry":"DE"},"telephone":"+49 2822 7131930","email":"info@metav-werkzeuge.com"},"about":[{"@type":"Thing","name":"Turning Holder Series"},{"@type":"Thing","name":"Lathe Tooling"},{"@type":"Thing","name":"Indexable Insert Holders"}],"mentions":[{"@type":"Thing","name":"K11-IK Insert Adapter"},{"@type":"Thing","name":"Internal Coolant Feature"},{"@type":"Thing","name":"SVJCR 2020 ISO Designation"}]}]}

Introducing Turning Holder — Clamp Holder for VCMT/DCMT Inserts by Teknik Makina The Turning Holder is a clamp holder designed for VCMT and DCMT indexable inserts, offering internal cooling and a precise 93° cutting angle for reliable metalworking performance. Clamp holder with internal cooling Compatible with DCMT 11T3 and VCMT inserts Precise 93° cutting angle for consistent surfaces Compact design: 150 mm overall length Stable SVJCR 1616 mounting for repeatable accuracy Precision and Stability that Reduce Rework A robust Clamp Holder delivers the foundation for accurate turning operations. Crafted to hold VCMT and DCMT indexable inserts securely, this holder minimises vibration and ensures repeatable positioning of the cutting edge. The result is improved surface finish and reduced scrap rates, which helps maintain process quality during serial production runs. Internal Cooling to Extend Tool Life Built-in Internal Cooling channels deliver coolant directly to the cutting zone, improving chip evacuation and reducing thermal load on the insert. This targeted coolant feed reduces flank wear and can extend the service intervals of the cutting edges, so fewer tool changes are required and uptime increases. Fast Insert Changes and Wide Compatibility Designed for quick handling, the clamp enables rapid loosening and fastening of inserts, making routine swaps straightforward. Compatibility with DCMT 11T3, VCMT 1103 and VCMT 1604 inserts gives versatility across different machining tasks, allowing the same holder to be used for varied geometries and materials without extensive retooling. Suitable Applications and Who Benefits This tool is aimed at machinists and workshops that require dependable turning performance for small to medium components. The compact 150 mm length and 25 mm cross-section make it suitable for operations where space is limited but precision is essential. Manufacturers seeking stable clamping and consistent results will find this holder a practical addition to their tooling set. Choose Teknik Makina’s Turning Holder for dependable accuracy and contact METAV Werkzeuge for personalised technical advice at info@metav-werkzeuge.com or +49 2822 7131930 — WhatsApp: +49 170 2837271 Bezeichnung: Klemmhalter SVJC für VCMT Wendeplatten Manufacturer: Teknik Makina SKU: AP520TM Suitable Inserts: DCMT 11T3, VCMT 1103, VCMT 1604 ISO designation: SVJCR 1616 Overall length: 150 mm Width: 25 mm Height: 25 mm Cutting head width: 32 mm Cutting angle: 93° Cutting direction: left Cutting height: 35 mm Weight: 0.735 kg Condition: new Availability: in Stock GTIN: 4061905052422 Torx key: T8 Torx screw: M2,5x6,5 Manufacturer: Teknik Makina, Nolu Sokak, No 9, Selcuklu, Turkey, eMail: info@teknik-makina.com Responsible Person: Metav Werkzeuge GmbH, Parkring 45, 46446 Emmerich, eMail: info@metav-werkzeuge.com FAQ What inserts fit the Turning Holder from Teknik Makina and which materials can I machine with it? The Turning Holder by Teknik Makina fits DCMT 11T3 and VCMT insert types such as VCMT 1103 and VCMT 1604, and it is suitable for a wide range of ferrous and non-ferrous machining tasks where these inserts are recommended. Does the Teknik Makina Turning Holder provide coolant delivery and how does that affect performance? Yes, the Teknik Makina Turning Holder features Internal Cooling that directs coolant to the cutting edge, improving chip evacuation and reducing tool temperature for longer insert life and more consistent machining results. How simple is it to change inserts on the Teknik Makina clamp holder? Changing inserts on this clamp holder is straightforward: screws are easy to access and the design supports quick insert exchange, helping to reduce machine downtime and speed up tool maintenance routines. Can METAV Werkzeuge provide technical support for choosing the right holder variant? METAV Werkzeuge offers comprehensive advice for tooling selection; contact METAV Werkzeuge at info@metav-werkzeuge.com or +49 2822 7131930 for tailored recommendations regarding the Turning Holder and compatible inserts. 93mm SVJCR 1616 Clamp Holder for VCMT/DCMT Inserts, Internal Coolant, 150mm - Teknik Makina

Turning Holder (Klemmhalter) by Teknik Makina The Turning Holder SVJC for VCMT Indexable Inserts provides secure clamping for DCMT 11T3 inserts and is designed for precision external turning in professional metalworking applications. Compatible with DCMT 11T3 indexable inserts Stable SVJCL 2525 clamping geometry for repeatability Integrated internal coolant for improved chip evacuation 150 mm Overall length for extended reach 93° Cutting angle for controlled material engagement Robust design and reliable insert compatibility The tool body is engineered to accept DCMT 11T3 indexable inserts and follows the SVJCL 2525 ISO designation, delivering a predictable interface between insert and holder. With a 150 mm overall length and a compact 25 mm cross-section, the holder offers a balance of stability and accessibility that reduces chatter and improves surface finish. This design choice leads to fewer rejects and a more consistent cut when changing inserts. Precise cutting geometry for consistent results A defined 93° cutting angle and left-hand cutting orientation produce reliable chip formation and controlled cutting forces. The holder’s geometry supports a focused contact area that enhances dimensional accuracy and surface quality, making it suitable for finishing and semi-finishing operations where tight tolerances matter. Precision in the toolholder translates directly into repeatable part quality. Internal coolant and maintenance-friendly assembly Equipped with Internal Coolant, the holder channels cutting fluid directly to the cutting edge, improving cooling and chip evacuation which extends insert life and lowers thermal deformation. Routine maintenance is simplified by the accessible fastening using a T15 Torx key and M3.5x11 Torx screw, allowing quick insert changes and secure clamping without specialised tools. Intended users and workshop applications Designed for professional workshops and CNC turning centres, this clamping solution from Teknik Makina suits machinists who require dependable performance for medium to heavy-duty external turning. The combination of compact dimensions and coolant capability makes it particularly useful in mixed-production environments where flexibility, tool life and surface integrity are priorities. Strong recommendation: Choose the Teknik Makina Turning Holder for dependable, coolant-fed turning — for specification checks or application advice contact METAV Werkzeuge at info@metav-werkzeuge.com or call +49 2822 7131930 (WhatsApp +49 170 2837271). Designation: Turning Holder (Klemmhalter) Brand / Manufacturer: Teknik Makina SKU: AP536TM For Indexable Inserts: DCMT 11T3 ISO Designation: SVJCL 2525 Overall Length: 150 mm Width: 25 mm Height: 25 mm Cutting Head Width: 32 mm Cutting Height: 35 mm Cutting Angle: 93° Cutting Direction: Left Internal Coolant: Yes Toolholder Shank Designation: M16-IK Torx Key: T15 Torx Screw: M3.5x11 Weight: 0.735 kg Availability: In Stock Condition: New GTIN: 4061905052606 Manufacturer: Teknik Makina, Nolu Sokak, No 9, Selcuklu, Türkiye, eMail: info@teknik-makina.com Responsible Person: Metav Werkzeuge GmbH, Parkring 45, 46446 Emmerich, eMail: info@metav-werkzeuge.com FAQ What inserts fit the Turning Holder from Teknik Makina? The Turning Holder by Teknik Makina is specified for DCMT 11T3 indexable inserts; the SVJCL 2525 interface ensures correct seating and clamping of these inserts for consistent cutting performance. Does the Teknik Makina Turning Holder support coolant supply? Yes, the Teknik Makina Turning Holder features Internal Coolant, which directs fluid to the cutting edge to enhance cooling and chip evacuation, thereby prolonging insert life. How is the insert secured and maintained on the Turning Holder? Inserts on this Turning Holder are secured with a Torx screw assembly (use a T15 key with an M3.5x11 screw), allowing straightforward insert changes and reliable clamping for repeatable machining results. 150mm Turning Holder SVJCL 2525 for DCMT 11T3, 93° With Internal Cooling - Teknik Makina

Comprehensive Technical Specifications: Order Number: KE34TM Item: Boring Bar usable with DCMT 11T3 Indexable Inserts Brand: Teknik Makina ISO Code: E20S SDUCR 11 Numbers and Data: Diameter: 25mm Weight: 0.95kg Total length: 250mm Cutting Height: 13mm Diameter Connection: 20mm Additional Informattion made of Vollhartmetall Cutting Direction: rechts Cooling Manufacturer Teknik Makina, Nolu Sokak, No 9, Selcuklu, Turkey, eMail: info@teknik-makina.com Responsible for Europe Metav Werkzeuge GmbH, Parkring 45, 46446 Emmerich, Germany, eMail: info@metav-werkzeuge.com

Available Technical Details: Order Number: KE44TM Item: Boring Bar usable with DCMT 11T3 Indexable Inserts Brand: Teknik Makina ISO Code: E20S SDUCL 11 Structural Details: Diameter: 25mm Weight: 0.95kg Total length: 250mm Cutting Height: 13mm Diameter Connection: 20mm Additional Informattion made of Vollhartmetall Cutting Direction: links Cooling Manufacturer Teknik Makina, Nolu Sokak, No 9, Selcuklu, Turkey, eMail: info@teknik-makina.com Responsible for Europe Metav Werkzeuge GmbH, Parkring 45, 46446 Emmerich, Germany, eMail: info@metav-werkzeuge.com

Turning Holder — SDHC for DCMT Indexable Inserts by Teknik Makina The Turning Holder is a robust SDHC clamping tool designed for left-hand turning with DCMT 11T3 indexable inserts, suitable for precision external turning in workshop and production environments. Compatible with DCMT 11T3 indexable inserts Overall length 125 mm for stable overhang ISO designation SDHCL 2020 for clear tool selection Left-hand cutting orientation for specific lathe setups Cutting head width 25 mm for rigid clamping Consistent clamping for repeatable turning results The clamping geometry of this holder is configured to secure DCMT 11T3 inserts with minimal runout, delivering consistent cutting conditions across batches. Thanks to the SDHCL 2020 designation, the tool can be matched quickly to setup sheets and CAM data. The 125 mm overall length balances accessibility and stiffness, reducing vibration and improving surface finish for external turning operations. Rigidity and design reduce tool deflection A compact cross-section with a 20 mm Width and 20 mm Height increases the holder's rigidity during cuts, ensuring stable chip formation and extended insert life. The 25 mm cutting-head width concentrates clamping force where it matters, which translates to improved dimensional accuracy. Left-hand cutting orientation is explicitly defined to avoid setup errors and to match specific lathe configurations. Optimised for professional workshops and serial production This SDHC Turning Holder is aimed at machinists and production engineers who require reliable toolholding for repeatable parts. The design supports frequent insert changes and precise indexation, making it suitable for medium to high-volume turning tasks. For shops that standardise on triangular indexable inserts, the holder simplifies tooling logistics and maintenance. Quick orientation and practical notes for mounting Install the insert so that the rake face and seating match the holder pocket geometry; the SDHC clamping system secures the DCMT 11T3 insert reliably while allowing correct indexation. The specified left-hand cutting direction must be observed when planning toolpaths or programming lathe cycles. For unfamiliar users: DCMT 11T3 denotes a triangular indexable insert (DCMT shape) with a 11T3 size, commonly used for external turning on a wide range of materials. Choose Teknik Makina’s precision Turning Holder with SDHC clamping for dependable machining — for tailored technical advice and support contact METAV Werkzeuge at info@metav-werkzeuge.com or call +49 2822 7131930 (WhatsApp +49 170 2837271). Technical specifications Bezeichnung: Klemmhalter Brand: Teknik Makina SKU: D350TM Secondary designation: SDHC for DCMT Indexable Inserts Compatible inserts: DCMT 11T3 ISO designation: SDHCL 2020 Total length: 125 mm Weight: 0.411 kg Cross-section width: 20 mm Cross-section height: 20 mm Cutting head width: 25 mm Cutting direction: left Cutting angle: 107.5° GTIN: 4061905153501 Manufacturer: Teknik Makina, Nolu Sokak, No 9, Selcuklu, Turkey, eMail: info@teknik-makina.com Responsible Person: Metav Werkzeuge GmbH, Parkring 45, 46446 Emmerich, eMail: info@metav-werkzeuge.com FAQ What inserts fit the Turning Holder from Teknik Makina? The Turning Holder by Teknik Makina is designed for DCMT 11T3 indexable inserts; these triangular inserts seat in the SDHC pocket and are clamped securely for external turning. Is this Turning Holder suitable for right-hand and left-hand operations? This specific Turning Holder is configured for left-hand cutting; Teknik Makina's designation and the product documentation should be checked for alternative orientations if right-hand operations are required. How does the SDHCL 2020 designation help in selecting the correct tool? The ISO-style SDHCL 2020 code identifies the holder geometry and pocket type, simplifying tool selection and ensuring compatibility with the intended DCMT 11T3 inserts from Teknik Makina. Who can I contact for technical support or installation advice? For technical guidance on the Turning Holder from Teknik Makina, METAV Werkzeuge provides competent advice — email info@metav-werkzeuge.com, call +49 2822 7131930, or reach out via WhatsApp at +49 170 2837271. 125mm SDHCL 2020 Turning Holder for DCMT 11T3, 107.5° Left - Teknik Makina

Turning Holder (Klemmhalter SDACR-F for DCMT Indexable Inserts) by Teknik Makina The Turning Holder (Klemmhalter) delivers secure clamping for DCMT indexable inserts and is engineered for precise, repeatable turning in workshop and production environments. Turning Holder for DCMT 11T3 inserts ISO SDACR 2020 geometry for secure clamping 125 mm overall length for standard tool setups 20 x 20 mm shank for stable machining Right-hand 90° cutting angle for conventional turning High-precision clamping that stabilises cuts Designed to hold DCMT 11T3 inserts with consistent seating, this tool holder focuses on Clamping accuracy to reduce vibration and enhance surface finish. The SDACR 2020 geometry ensures a repeatable insert position and reliable cutting edge support, which translates directly into fewer rejects and longer tool life. For operators who value predictability, the holder’s clamping concept simplifies setup while maintaining the cutting forces where they belong. Compact dimensions that ease machine integration With an overall length of 125 mm and a compact 20 x 20 mm shank, the holder fits standard turret stations and compact lathe fixtures without compromising rigidity. These dimensions enable a lower overhang, reducing deflection at higher spindle speeds and improving dimensional accuracy on turned parts. The compact format also facilitates faster tool changes and better access to complex geometries in small-batch and series production. Geometry optimised for right-hand conventional turning The Right-hand orientation combined with a 90° approach angle creates a versatile configuration for general turning and shoulder work. This setup supports predictable chip flow and repeatable part geometry in facing and longitudinal turning operations. For jobs requiring consistent shoulder faces or stepped diameters, the holder’s angle and orientation help maintain tool path stability and surface quality. Built for workshops and production lines seeking reliability Workshops and production lines benefit from a straightforward, robust design that minimises downtime and simplifies tooling management. The holder is compatible with commonly used DCMT 11T3 inserts, allowing fast replacement and broad application across materials. Should further technical clarification be needed, METAV Werkzeuge provides expert advice and support to confirm fitment and machining strategy — reachable via the contact information below. Strong recommendation: Choose Teknik Makina’s Turning Holder with SDACR 2020 geometry for precise, stable turning — for personalised technical advice contact METAV Werkzeuge at info@metav-werkzeuge.com or call +49 2822 7131930 Technical Specifications for installation and compatibility Designation: Klemmhalter Brand: Teknik Makina SKU: D444TM Suitable for inserts: DCMT 11T3 Overall length: 125 mm Weight: 0.397 kg ISO designation: SDACR 2020 Secondary designation: K11-F Width: 20 mm Height: 20 mm Cutting head width: 20 mm Cutting direction: right Cutting angle: 90° GTIN: 4061905153433 Availability: in Stock Manufacturer: Teknik Makina, Nolu Sokak, No 9, Selcuklu, Türkiye, eMail: info@teknik-makina.com Responsible Person: Metav Werkzeuge GmbH, Parkring 45, 46446 Emmerich, eMail: info@metav-werkzeuge.com FAQ What inserts fit the Turning Holder by Teknik Makina and which insert size is recommended? The Turning Holder (Klemmhalter) from Teknik Makina is designed for DCMT 11T3 inserts; using standard DCMT 11T3 inserts ensures correct seating and optimal cutting performance. Can the Turning Holder (Klemmhalter) by Teknik Makina be used on compact lathes? Yes, the Turning Holder by Teknik Makina features a 125 mm overall length and a 20 x 20 mm shank, which makes the holder suitable for many compact lathe turrets and tight setups. Is the SDACR 2020 geometry of the Turning Holder important for my production runs? The SDACR 2020 geometry in this Turning Holder (Klemmhalter) by Teknik Makina stabilises the insert position and reduces vibration, which benefits repeatability and surface finish in series production. Who can I contact for help choosing the right Turning Holder from Teknik Makina? If you need extra technical data or assistance selecting the right Turning Holder, METAV Werkzeuge offers competent consultation — email info@metav-werkzeuge.com or call +49 2822 7131930, WhatsApp +49 170 2837271. {"@context":"https://schema.org","@graph":[{"@type":"Product","@id":"#D444TM","sku":"D444TM","mpn":"SDACR 2020","gtin13":"4061905153433","name":"Klemmhalter SDACR 2020 90° DCMT 11T3","description":"125mm turning holder for DCMT 11T3 indexable inserts; SDACR-F design, 20mm width/height, right-hand, aluminium construction ideal for reliable turning.","image":["https://files.plytix.com/api/v1.1/file/public_files/pim/assets/57/c3/98/62/6298c3575d155f1bc7e497fd/images/13/87/1d/64/641d8713eb4c191311cc52d1/d434tm-main.png","https://files.plytix.com/api/v1.1/file/public_files/pim/assets/57/c3/98/62/6298c3575d155f1bc7e497fd/images/2c/7e/de/62/62de7e2c33927e49dbf3272f/d434tm-artikelliste.jpg","https://files.plytix.com/api/v1.1/file/public_files/pim/assets/57/c3/98/62/6298c3575d155f1bc7e497fd/images/cf/7e/de/62/62de7ecf0f56dbb4de4dbf3e/d434tm-technische-zeichnung.jpg"],"additionalProperty":[{"@type":"PropertyValue","name":"Designation","value":"Turning Holder"},{"@type":"PropertyValue","name":"Designation 2","value":"SDACR-F for DCMT indexable inserts"},{"@type":"PropertyValue","name":"For Inserts","value":"DCMT 11T3"},{"@type":"PropertyValue","name":"Overall Length","value":"125 mm"},{"@type":"PropertyValue","name":"Width","value":"20 mm"},{"@type":"PropertyValue","name":"Height","value":"20 mm"},{"@type":"PropertyValue","name":"Cutting Head Width","value":"20 mm"},{"@type":"PropertyValue","name":"Cutting Direction","value":"Right"},{"@type":"PropertyValue","name":"Cutting Angle","value":"90°"},{"@type":"PropertyValue","name":"Weight","value":"0.397 kg"},{"@type":"PropertyValue","name":"ISO Designation","value":"SDACR 2020"}]},{"@type":"FAQPage","mainEntity":[{"@type":"Question","name":"What inserts does this holder take?","acceptedAnswer":{"@type":"Answer","text":"Compatible with DCMT 11T3 indexable inserts."}},{"@type":"Question","name":"What is the overall length of the holder?","acceptedAnswer":{"@type":"Answer","text":"Overall length is 125 mm."}},{"@type":"Question","name":"What are the holder dimensions?","acceptedAnswer":{"@type":"Answer","text":"Width and height are 20 mm; cutting head width 20 mm."}},{"@type":"Question","name":"What is the cutting angle and direction?","acceptedAnswer":{"@type":"Answer","text":"Cutting angle 90°; right-hand cutting direction."}},{"@type":"Question","name":"Who is the manufacturer?","acceptedAnswer":{"@type":"Answer","text":"Manufacturer: Teknik Makina."}}]},{"@type":"ItemPage","url":"https://metav-shop.de/klemmhalter-sdacr-2020-90-dcmt-11t3","dateModified":"2026-04-16T12:00:00+01:00","author":{"@type":"Person","name":"Stephan Bayer","url":"https://www.linkedin.com/in/stephan-bayer/"},"publisher":{"@type":"Organization","name":"Metav Werkzeuge GmbH","url":"https://metav-shop.de","logo":{"@type":"ImageObject","url":"https://files.plytix.com/api/v1.1/file/public_files/pim/assets/57/c3/98/62/6298c3575d155f1bc7e497fd/images/8e/48/c5/69/69c5488eb2b3400ba580741c/logo-metav-1200-675.png","width":1200,"height":675},"address":{"@type":"PostalAddress","streetAddress":"Parkring 45","postalCode":"46446","addressLocality":"Emmerich","addressCountry":"DE"},"telephone":"+49 2822 7131930","email":"info@metav-werkzeuge.com"},"about":[{"@type":"Thing","name":"SDACR 2020 Turning Holder"},{"@type":"Thing","name":"DCMT 11T3 Compatibility"},{"@type":"Thing","name":"125 mm Overall Length"}],"mentions":[{"@type":"Thing","name":"SDACR-F for DCMT indexable inserts"},{"@type":"Thing","name":"K11-F shank option"},{"@type":"Thing","name":"90° cutting angle"}]}]}

Turning Holder SVJCL 2020 for DCMT 11T3 Indexable Inserts by Teknik Makina The Turning Holder SVJCL 2020 is a precision lathe holder designed for DCMT 11T3 indexable inserts, optimised for left-hand turning operations and workshop reliability. SVJCL 2020 ISO designation for reliable fit Fits DCMT 11T3 indexable inserts Internal Coolant for improved tool life 150 mm overall length for stable setup 93° Cutting Angle for left-hand turning Robust clamping for consistent machining results The Holder’s SVJCL 2020 design provides a secure clamping interface that minimises Insert movement under load. Built with a 32 mm Cutting Head Width and a solid cross-section, the tool gives dependable rigidity during longer cuts. This stability reduces chatter and supports consistent Surface Finish, which translates directly into less rework and higher first-pass yield for production runs. Integrated coolant and precise cutting geometry for longer tool life Equipped with Internal Coolant, the tool directs lubricant and coolant close to the cutting zone to manage temperature and evacuate chips effectively. Coupled with a 93° Cutting Angle configured for left-hand cutting, this arrangement helps maintain Insert edge integrity and extends service intervals. The result is improved Tool Life and predictable performance during demanding turning tasks. Stable setup and secure fastening for efficient workshop use With a 150 mm Overall Length and compact 25 mm Width and Height dimensions, the Holder balances reach and stiffness to suit many setups. Fastening is straightforward using a Torx T8 key and M2.5x6.5 screw format, ensuring repeatable clamping torque and quick reassembly during Insert changes. These features reduce downtime and simplify maintenance in a busy shop environment. Direct compatibility with DCMT 11T3 inserts and practical handling Designed specifically for DCMT 11T3 indexable inserts, the Holder guarantees precise seating and correct cutting geometry without additional shims or adapters. The nominal Cutting Height of 35 mm positions the Insert correctly for standard toolpost setups. Assembly and Insert replacement are intuitive, making the tool suitable for both experienced operators and technicians new to precision turning. Highly recommend the Teknik Makina Turning Holder for precise left-hand turning tasks — for personalised technical advice or to confirm fitment contact METAV Werkzeuge at info@metav-werkzeuge.com or call +49 2822 7131930, WhatsApp +49 170 2837271 Designation: Turning Holder Brand: Teknik Makina SKU: AP531TM For Indexable Inserts: DCMT 11T3 ISO Designation: SVJCL 2020 Overall Length: 150 mm Weight: 0.735 kg Width: 25 mm Height: 25 mm Cutting Head Width: 32 mm Cutting Height: 35 mm Cutting Angle: 93° Cutting Direction: Left Internal Coolant: Yes Torx Key: T8 Torx Screw: M2.5x6.5 GTIN: 4061905052538 Manufacturer / Manufacturer: Teknik Makina, Nolu Sokak, No 9, Selcuklu, Türkei, eMail: info@teknik-makina.com Responsible Person / Responsible Person: Metav Werkzeuge GmbH, Parkring 45, 46446 Emmerich, eMail: info@metav-werkzeuge.com FAQ What inserts does the Turning Holder by Teknik Makina accept? The Turning Holder from Teknik Makina is designed to accept DCMT 11T3 indexable inserts, ensuring correct seating and the intended cutting geometry without additional adapters. Does the Teknik Makina Turning Holder support coolant-through operation? Yes, the Turning Holder features Internal Coolant to deliver lubricant directly to the cutting zone, which helps control temperature and extend Insert life during continuous machining. Is the SVJCL 2020 holder suitable for left-hand turning? The SVJCL 2020 configuration of this Turning Holder is manufactured with a 93° Cutting Angle and is specified for left-hand turning applications, providing appropriate geometry for that direction of cut. How is the Turning Holder fastened and maintained? Fastening uses a Torx T8 key and M2.5x6.5 screw format for secure, repeatable clamping; routine maintenance consists of standard Insert replacement and periodic inspection of the clamping screw torque. If further technical details are required, METAV Werkzeuge provides expert support at info@metav-werkzeuge.com or +49 2822 7131930. 150mm SVJCL 2020 Turning Holder for DCMT 11T3, 93° Cutting Angle - Teknik Makina

Technical Specifications: Order Number: S070TM Item: T-Grove Holder usable with DCMT 11T3 Indexable Inserts Brand: Teknik Makina Metric Information: Diameter: 50mm Cutting Edges: 3 Weight: 0.584kg Total length: 120mm Manufacturer Teknik Makina, Nolu Sokak, No 9, Selcuklu, Turkey, eMail: info@teknik-makina.com Responsible for Europe Metav Werkzeuge GmbH, Parkring 45, 46446 Emmerich, Germany, eMail: info@metav-werkzeuge.com

Turning Holder SVJCL 1616 by Teknik Makina The Turning Holder SVJCL 1616 is a right-hand clamping toolholder designed for stable, precision turning with DCMT 11T3 indexable inserts. SVJCL 1616 ISO designation for precise mounting 150 mm overall length for extended reach Internal cooling for improved chip evacuation Compatible with DCMT 11T3 indexable inserts 93° cutting angle for stable right-hand turning Durable Design for Consistent Clamping and Tool Life The holder is engineered with a robust clamping head that ensures stable seating of indexable inserts and reduces vibration during cutting. Its compact dimensions — 25 mm Width and 25 mm Height — together with a 32 mm cutting-head width, provide a balance between rigidity and accessibility in confined setups. This construction supports consistent surface finish and longer Insert life, translating to fewer tool changes and increased uptime. Machining Performance and Process Reliability Built for right-hand operations with a 93° cutting angle and a 35 mm cutting height, the toolholder delivers predictable chip flow and cutting forces for a wide range of Turning operations. The 150 mm overall length enables extended reach without excessive deflection, and compatibility with DCMT 11T3 indexable inserts allows for flexible grade selection depending on material and cut. These features combine to improve cycle times and reproducible results in serial production. Where this Tool Excels and Who Benefits This clamping solution is aimed at workshops and manufacturers who require repeatable precision in metalcutting tasks, from medium-duty lathe work to more complex turning operations. Operators and process engineers will appreciate the straightforward insert change and the holder’s adaptability to standard insert geometries. For customers seeking application-specific setup or verification, METAV Werkzeuge provides experienced advice and specification support via email or phone. Easy Setup, Maintenance and Safe Operation Assembly and maintenance are simplified by standard fastenings: Torx key T8 and Torx screw M2.5x6.5 secure the clamping components, allowing quick service intervals and reliable torque settings. The holder features Internal Cooling: Yes, improving chip evacuation and tool life when connected to a coolant supply. Regular inspection of clamping surfaces and screw torque ensures ongoing accuracy and safe operation. For precision turning tasks where reliability matters, choose the Teknik Makina Turning Holder SVJCL 1616 — for expert application advice contact METAV Werkzeuge at info@metav-werkzeuge.com or call +49 2822 7131930, WhatsApp +49 170 2837271. Technical Data Bezeichnung: Turning Holder Brand: Teknik Makina SKU: AP530TM Compatible Indexable Inserts: DCMT 11T3 ISO Designation: SVJCL 1616 Secondary Designation: H11-IK Overall Length: 150 mm Width: 25 mm Height: 25 mm Cutting Head Width: 32 mm Cutting Height: 35 mm Cutting Direction: Right Cutting Angle: 93° Internal Cooling: Yes Torx Key: T8 Torx Screw: M2.5x6.5 Weight: 0.735 kg GTIN: 4061905052521 Condition: New Availability: In Stock eClass: 21181004 Label: Klemmhalter SVJCL 1616 93° DCMT 11T3 Manufacturer: Teknik Makina, Nolu Sokak, No 9, Selcuklu, Turkey, eMail: info@teknik-makina.com Responsible Person: Metav Werkzeuge GmbH, Parkring 45, 46446 Emmerich, eMail: info@metav-werkzeuge.com FAQ What inserts fit the Turning Holder from Teknik Makina? The Teknik Makina Turning Holder SVJCL 1616 is compatible with DCMT 11T3 indexable inserts, enabling easy selection of grades for different workpiece materials and machining conditions. Does the Turning Holder SVJCL 1616 support coolant-through operation? Yes, the Turning Holder SVJCL 1616 from Teknik Makina features internal cooling, which assists chip evacuation and can extend tool life when a coolant supply is used. Which hand orientation is the clamping holder designed for? The Teknik Makina clamping holder SVJCL 1616 is configured for right-hand turning, with a 93° cutting angle optimized for stable right-side cuts. Who can help if I need setup advice for the Turning Holder? METAV Werkzeuge offers competent consultation for application and technical queries related to the Teknik Makina Turning Holder SVJCL 1616 — contact info@metav-werkzeuge.com or call +49 2822 7131930 for support. 150mm Turning Holder SVJCL 1616 for DCMT 11T3, 93° Cutting Angle, Internal Coolant - Teknik Makina

Product Information: Order Number: KE50TM Item: Boring Bar usable with DCMT 0702 Indexable Inserts Brand: Teknik Makina ISO Code: E10K SDQCR 07 Structural Details: Diameter: 13mm Weight: 0.05kg Total length: 125mm Cutting Height: 7mm Diameter Connection: 10mm Additional Informattion made of Vollhartmetall Cutting Direction: rechts Cooling Manufacturer Teknik Makina, Nolu Sokak, No 9, Selcuklu, Turkey, eMail: info@teknik-makina.com Responsible for Europe Metav Werkzeuge GmbH, Parkring 45, 46446 Emmerich, Germany, eMail: info@metav-werkzeuge.com

Technical Data: Item: T-Grove Holder Brand: Teknik Makina Order Number: TKC251TM usable with DCMT 11T3 Indexable Inserts Diameter: 60mm Angle: 55° Total length: 120mm Cutting Edges: 4 Weight: 0.583kg Manufacturer Teknik Makina, Nolu Sokak, No 9, Selcuklu, Turkey, eMail: info@teknik-makina.com Responsible for Europe Metav Werkzeuge GmbH, Parkring 45, 46446 Emmerich, Germany, eMail: info@metav-werkzeuge.com

Turning Holder (SVJCL 2020) by Teknik Makina The Turning Holder is a precision clamping tool for machining that secures DCMT 11T3 indexable inserts for reliable left-hand cutting in turning applications. SVJCL 2020 clamping holder for DCMT 11T3 inserts Internal coolant for improved chip evacuation 150 mm overall length for extended reach 93° cutting angle for stable tool engagement 25 x 25 mm shank with 32 mm cutter head width High-precision clamping for consistent machining results The Turning Holder from Teknik Makina combines a robust clamping concept with a clear focus on positional stability. The SVJCL 2020 ISO designation reflects a geometry engineered to hold DCMT 11T3 Inserts securely, reducing micro-movement at the cutting edge and enabling consistent Surface Finish and dimensional accuracy. This stability translates into predictable tool life and reproducible component tolerances, which is especially valuable in serial production and tight-tolerance turning tasks. Controlled chip flow and thermal management for longer cycles Equipped with internal coolant, this clamping tool directs coolant close to the cutting zone to support chip evacuation and heat dissipation. The targeted coolant feed helps prevent built-up edge and reduces thermal load on the Insert, which in turn can extend the usable life of the cutting edge and support longer uninterrupted Cutting Cycles. For operators who process materials that produce long or stringy chips, the improved chip control reduces rework and machine downtime. Built for versatility across common turning setups Designed with a 150 mm Overall Length and a 25 x 25 mm Shank, the toolholder fits a wide range of lathe tool posts where extended reach and secure mounting are required. The 93° cutting angle and left-hand cutting direction make it suitable for typical face and profile turning operations using DCMT 11T3 Inserts. Technicians and production planners will appreciate the clear compatibility with established insert types, which simplifies tool inventory and changeover planning on the shop floor. Practical assembly and robust construction for everyday use Assembly and maintenance benefit from standardized fasteners and accessories: the unit accepts a Torx T15 key and uses M3.5x11 Torx screws, enabling quick insert clamping and secure fixation. The 32 mm cutter head width and the defined shank dimensions contribute to mechanical rigidity, while the ISO designation SVJCL 2020 allows straightforward documentation and ordering. Regular inspection of the clamping screw and coolant channels ensures reliable performance and helps maintain operational safety. Strongly recommended: choose Teknik Makina’s SVJCL 2020 Turning Holder for stable, coolant-assisted turning operations — for expert advice and precise application support contact METAV Werkzeuge at info@metav-werkzeuge.com or call +49 2822 7131930 Bezeichnung: Klemmhalter Marke: Teknik Makina SKU: AP535TM For Indexable Inserts: DCMT 11T3 Compatible Inserts: DCMT 11T3 Overall Length: 150 mm Weight: 0.735 kg ISO Designation: SVJCL 2020 Secondary Designation: K16-IK Shank Width: 25 mm Shank Height: 25 mm Cutter Head Width: 32 mm Cutting Angle: 93° Cutting Direction: Left Internal Coolant: true Torx Key: T15 Torx Screw: M3,5x11 U-Plate: TA034 GTIN: 4061905052545 GMC Availability: in Stock GMC Condition: new Manufacturer: Teknik Makina, Nolu Sokak, No 9, Selcuklu, Türkei, eMail: info@teknik-makina.com Responsible Person: Metav Werkzeuge GmbH, Parkring 45, 46446 Emmerich, eMail: info@metav-werkzeuge.com FAQ What inserts does the Turning Holder by Teknik Makina accept? The Turning Holder by Teknik Makina is designed specifically for DCMT 11T3 indexable inserts, ensuring correct seating and clamping for that insert geometry. Is internal coolant available with this Turning Holder from Teknik Makina? Yes, the Teknik Makina Turning Holder includes internal coolant channels to support chip evacuation and cooling at the cutting zone. Can the Teknik Makina Turning Holder be used for left-hand and right-hand turning? This particular Turning Holder is configured for left-hand cutting direction; for right-hand applications, please check Teknik Makina’s alternate holders or contact METAV Werkzeuge for guidance. Who can I contact for application advice or if the Turning Holder by Teknik Makina does not match my setup? For expert consultation regarding the Teknik Makina Turning Holder and its fit for your machine or process, contact METAV Werkzeuge at info@metav-werkzeuge.com or call +49 2822 7131930; WhatsApp is also available at +49 170 2837271. 93° Left Cutting SVJCL 2020 Turning Holder for DCMT 11T3, 150mm - Teknik Makina

Technical Specifications: Order Number: KE63TM Item: Boring Bar usable with DCMT 11T3 Indexable Inserts Brand: Teknik Makina ISO Code: E16R SDQCL 11 Quantitative Characteristics: Diameter: 20mm Weight: 0.5kg Total length: 200mm Cutting Height: 11mm Diameter Connection: 16mm Additional Informattion made of Vollhartmetall Cutting Direction: links Cooling Manufacturer Teknik Makina, Nolu Sokak, No 9, Selcuklu, Turkey, eMail: info@teknik-makina.com Responsible for Europe Metav Werkzeuge GmbH, Parkring 45, 46446 Emmerich, Germany, eMail: info@metav-werkzeuge.com

Clamp Holder SDHC for DCMT Indexable Inserts — Turning Holder by Teknik Makina The Clamp Holder SDHC for DCMT Indexable Inserts is a robust Turning Holder engineered for secure clamping and precise 107.5° cutting performance in professional turning operations. Clamp holder for DCMT 11T3 inserts 107.5° cutting angle for accurate surfaces Removable screws enable quick insert change 125 mm overall length for versatile setups Stable clamping reduces vibration and rework Boost Productivity with Precise 107.5° Cutting The Clamp Holder SDHC for DCMT Indexable Inserts delivers measurable gains in Productivity by providing a consistent 107.5° cutting geometry that supports repeatable machining results. The defined cutting angle reduces manual adjustments and scrap rates, which translates into lower production costs and less rework. For workshops that measure output in cycle times and first-pass yield, this holder helps keep processes predictable and efficient. Fast Tool Changes and Reliable Clamping for Continuous Operation Designed with Quick Change in mind, the holder features easily removable screws that allow fast replacement of DCMT 11T3 inserts. This minimises machine downtime during regrinds or insert swaps and supports lean workflows on the shop floor. The Stable Clamping and precise seat alignment ensure the insert remains fixed during heavy cuts, reducing micro-movements that cause tool wear and poor surface finish. Versatile Use Across Materials and Turning Tasks This SDHC Clamp Holder is suitable for a broad range of turning applications, from finishing to semi‑roughing, and accepts the widely available DCMT 11T3 indexable inserts. Its 125 mm overall length and well-defined cutting-head width make it compatible with many turret and toolpost configurations, offering flexibility in set-up and part handling. Technical teams and operators will value the combination of adaptability and consistent cutting behaviour. Practical Advantages and What Indexable Inserts Mean for You Indexable inserts allow replacing only the cutting edge rather than the entire tool, which reduces tooling costs and shortens setup time. The holder’s compatibility with ISO-standard inserts provides access to a wide variety of grades and geometries for different workpiece materials. Choosing a system with standardised inserts supports predictable tool-life planning and easier inventory management, improving overall workshop economics. Highly recommended: For dependable turning performance and reduced setup time, choose the Teknik Makina Clamp Holder SDHC for DCMT Indexable Inserts — for expert advice and order support contact METAV Werkzeuge at info@metav-werkzeuge.com or call +49 2822 7131930 (WhatsApp +49 170 2837271). Technical Data Bezeichnung: Klemmhalter SDHC für DCMT Wendeplatten Marke: Teknik Makina SKU: D250TM For Indexable Inserts: DCMT 11T3 Compatible Inserts: DCMT 11T3 Overall Length: 125 mm Weight: 0.411 kg ISO Designation: SDHCR 2020 Secondary Designation: K11 Width: 20 mm Height: 20 mm Cutting-Head Width: 25 mm Cutting Angle: 107.5° Cutting Direction: right GTIN: 4061905153488 Availability: in Stock Condition: new Manufacturer: Teknik Makina, Nolu Sokak, No 9, Selcuklu, Türkei, eMail: info@teknik-makina.com Responsible Person: Metav Werkzeuge GmbH, Parkring 45, 46446 Emmerich, eMail: info@metav-werkzeuge.com FAQ What inserts fit the Clamp Holder SDHC for DCMT Indexable Inserts from Teknik Makina? The Clamp Holder SDHC for DCMT Indexable Inserts by Teknik Makina is designed for standard DCMT 11T3 indexable inserts; using the specified insert type ensures correct seating, reliable clamping, and the intended 107.5° cutting geometry. How do I change the insert on the Teknik Makina Clamp Holder SDHC for DCMT Indexable Inserts? To replace an insert, loosen the removable clamping screw, remove the worn DCMT 11T3 insert, seat the new insert correctly and re-tighten the screw; this straightforward process minimises downtime and keeps the Turning Holder ready for immediate production. Which applications are best suited for the Clamp Holder SDHC for DCMT Indexable Inserts? The Clamp Holder SDHC for DCMT Indexable Inserts is suited to a wide range of turning tasks—finishing and semi‑roughing—across various materials; its stable clamping and standard insert compatibility make it a practical choice for demanding workshop environments. Need help selecting the right variant or further technical data for this Turning Holder? METAV Werkzeuge offers competent advice for tooling selection; if you’re unsure whether this Clamp Holder SDHC for DCMT Indexable Inserts matches your requirements, contact METAV Werkzeuge at info@metav-werkzeuge.com, call +49 2822 7131930 or WhatsApp +49 170 2837271 for personalised support. {"@context":"https://schema.org","@graph":[{"@type":"Product","@id":"#D250TM","sku":"D250TM","mpn":"D250TM","gtin13":"4061905153488","name":"Clamp Holder SDHCR 2020 107.5° DCMT 11T3","description":"Clamp holder SDHC for DCMT indexable inserts, 107.5° cutting angle, 125 mm overall length, compatible with DCMT 11T3; robust aluminium construction; fast tool changes for high productivity.","image":["https://files.plytix.com/api/v1.1/file/public_files/pim/assets/57/c3/98/62/6298c3575d155f1bc7e497fd/images/60/13/35/64/64351360edeb9298707ad344/d250tm-main.png","https://files.plytix.com/api/v1.1/file/public_files/pim/assets/57/c3/98/62/6298c3575d155f1bc7e497fd/images/2c/7e/de/62/62de7e2c0f56dbb4de4dbeeb/d250tm-artikelliste.jpg","https://files.plytix.com/api/v1.1/file/public_files/pim/assets/57/c3/98/62/6298c3575d155f1bc7e497fd/images/cf/7e/de/62/62de7ecf0f56dbb4de4dbf3d/d250tm-technische-zeichnung.jpg"],"additionalProperty":[{"@type":"PropertyValue","name":"For indexable inserts","value":"DCMT 11T3"},{"@type":"PropertyValue","name":"Cutting angle","value":"107.5°"},{"@type":"PropertyValue","name":"Overall length","value":"125 mm"},{"@type":"PropertyValue","name":"Cutting head width","value":"25 mm"},{"@type":"PropertyValue","name":"Width","value":"20 mm"},{"@type":"PropertyValue","name":"Height","value":"20 mm"},{"@type":"PropertyValue","name":"ISO designation","value":"SDHCR 2020"},{"@type":"PropertyValue","name":"Manufacturer","value":"Teknik Makina"},{"@type":"PropertyValue","name":"Weight","value":"0.411 kg"}]},{"@type":"FAQPage","mainEntity":[{"@type":"Question","name":"What inserts fit this clamp holder?","acceptedAnswer":{"@type":"Answer","text":"Compatible with DCMT 11T3 indexable inserts."}},{"@type":"Question","name":"What is the cutting angle?","acceptedAnswer":{"@type":"Answer","text":"The clamp holder features a 107.5° cutting angle for precise surface finishes."}},{"@type":"Question","name":"What is the overall length?","acceptedAnswer":{"@type":"Answer","text":"Overall length is 125 mm."}},{"@type":"Question","name":"What is the cutting head width?","acceptedAnswer":{"@type":"Answer","text":"Cutting head width is 25 mm."}},{"@type":"Question","name":"Who is the manufacturer?","acceptedAnswer":{"@type":"Answer","text":"Manufacturer: Teknik Makina."}}]},{"@type":"ItemPage","url":"https://metav-shop.de/d250tm","dateModified":"2026-04-16T12:00:00+01:00","author":{"@type":"Person","name":"Stephan Bayer","url":"https://www.linkedin.com/in/stephan-bayer/"},"publisher":{"@type":"Organization","name":"Metav Werkzeuge GmbH","url":"https://metav-shop.de","logo":{"@type":"ImageObject","url":"https://files.plytix.com/api/v1.1/file/public_files/pim/assets/57/c3/98/62/6298c3575d155f1bc7e497fd/images/8e/48/c5/69/69c5488eb2b3400ba580741c/logo-metav-1200-675.png","width":1200,"height":675},"address":{"@type":"PostalAddress","streetAddress":"Parkring 45","postalCode":"46446","addressLocality":"Emmerich","addressCountry":"DE"},"telephone":"+49 2822 7131930","email":"info@metav-werkzeuge.com"},"about":[{"@type":"Thing","name":"Clamp holder SDHC for DCMT indexable inserts"},{"@type":"Thing","name":"Allround turning applications"},{"@type":"Thing","name":"High productivity through quick insert change"}],"mentions":[{"@type":"Thing","name":"DCMT 11T3 inserts"},{"@type":"Thing","name":"107.5° cutting angle"},{"@type":"Thing","name":"SDHCR 2020 designation"},{"@type":"Thing","name":"Teknik Makina clamp holder"}]}]}

Available Technical Details: Order Number: TKC250TM Item: T-Grove Holder usable with DCMT 11T3 Indexable Inserts Brand: Teknik Makina Metric Information: Diameter: 50mm Cutting Edges: 4 Weight: 0.521kg Total length: 120mm Manufacturer Teknik Makina, Nolu Sokak, No 9, Selcuklu, Turkey, eMail: info@teknik-makina.com Responsible for Europe Metav Werkzeuge GmbH, Parkring 45, 46446 Emmerich, Germany, eMail: info@metav-werkzeuge.com

Technical Information: Order Number: KE54TM Item: Boring Bar usable with DCMT 11T3 Indexable Inserts Brand: Teknik Makina ISO Code: E20S SDQCR 11 Quantitative Characteristics: Diameter: 25mm Weight: 0.95kg Total length: 250mm Cutting Height: 13mm Diameter Connection: 20mm Additional Informattion made of Vollhartmetall Cutting Direction: rechts Cooling Manufacturer Teknik Makina, Nolu Sokak, No 9, Selcuklu, Turkey, eMail: info@teknik-makina.com Responsible for Europe Metav Werkzeuge GmbH, Parkring 45, 46446 Emmerich, Germany, eMail: info@metav-werkzeuge.com

Turning Holder — SVJCR 2525 Turning Holder by Teknik Makina The Turning Holder from Teknik Makina secures DCMT 11T3 indexable inserts for precise, right-hand turning operations in workshop and production environments. Teknik Makina SVJCR 2525 toolholder Compatible with DCMT 11T3 indexable inserts Internal coolant for improved chip evacuation Robust 25 x 25 mm shank for stable machining 150 mm overall length for versatile reach Precision and performance you can rely on Designed for consistent metalcutting, this Turning Holder delivers stable tool support thanks to its 25 x 25 mm shank and 32 mm cutting-head width. The holder’s geometry with a 93° cutting angle ensures predictable cutting forces and repeatable chip formation, which translates directly into improved surface finish and longer insert life. Compatibility with DCMT 11T3 inserts makes tooling selection straightforward for common turning tasks. Coolant-through design that extends insert life An integrated internal coolant channel guides cutting fluid directly to the cutting zone, enhancing cooling and chip control. This targeted coolant supply reduces thermal stress at the cutting edge and supports consistent tool life, especially during tougher turning operations. The result is fewer unscheduled insert changes and higher overall productivity for small-batch and serial machining. Thoughtful details for quick setup and maintenance Assembly and insert clamping are simplified with standard fastenings: the holder uses M3.5x11 torx screws and a T15 torx key, and it accepts the specified clamp plate TA034. These common components lower setup time and make maintenance straightforward for workshop technicians. The SVJCR 2525 ISO designation indicates a familiar mounting and handling profile for experienced machinists. Suitable applications and intended users This Turning Holder targets professional workshops and precision-turning environments that require reliable, right-hand turning of steel and similar materials. Operators who value repeatable results and straightforward insert compatibility will appreciate the combination of mechanical rigidity and coolant-through capability. The robust construction supports moderate to demanding turning tasks without unnecessary complexity. Choose the Teknik Makina Turning Holder with internal coolant and SVJCR 2525 geometry for dependable turning performance — for questions or tailored advice METAV Werkzeuge provides expert support at info@metav-werkzeuge.com, by phone +49 2822 7131930 or WhatsApp +49 170 2837271 Technical Specifications Bezeichnung: Turning Holder Brand: Teknik Makina SKU: AP526TM Compatible Inserts: DCMT 11T3 ISO Designation: SVJCR 2525 Secondary Designation: M16-IK Overall Length: 150 mm Shank Width: 25 mm Shank Height: 25 mm Cutting-Head Width: 32 mm Cutting Angle: 93° Cutting Direction: Right Internal Coolant: Yes Torx Key: T15 Torx Screw: M3.5x11 Clamp Plate: TA034 Weight: 0.735 kg Manufacturer: Teknik Makina, Nolu Sokak, No 9, Selcuklu, Turkey, eMail: info@teknik-makina.com Responsible Person: Metav Werkzeuge GmbH, Parkring 45, 46446 Emmerich, eMail: info@metav-werkzeuge.com FAQ What inserts fit the Turning Holder from Teknik Makina? The Turning Holder by Teknik Makina is designed to accept DCMT 11T3 indexable inserts, providing a straightforward selection for standard turning applications. Does the Teknik Makina Turning Holder support coolant-through machining? Yes, the Teknik Makina Turning Holder features internal coolant, enabling targeted cooling and improved chip control at the cutting edge. Which shank size and ISO designation does this Turning Holder use? This holder uses a 25 x 25 mm shank and carries the SVJCR 2525 ISO designation, offering a familiar mounting profile for workshop toolholders. Who can help if I need technical advice about the Turning Holder? For detailed support regarding the Turning Holder from Teknik Makina, METAV Werkzeuge offers expert consultation — contact info@metav-werkzeuge.com or call +49 2822 7131930. {"@context":"https://schema.org","@graph":[{"@type":"Product","@id":"#AP526TM","sku":"AP526TM","mpn":"AP526TM","gtin13":"4061905052514","name":"150mm Turning Holder SVJCR 2525 93° for DCMT 11T3 Inserts - Teknik Makina","description":"150mm turning holder with internal coolant, ISO SVJCR 2525, fits DCMT 11T3 indexable inserts; 25x25mm shank, 32mm cutting head width, right-hand 93° geometry.","image":["https://files.plytix.com/api/v1.1/file/public_files/pim/assets/57/c3/98/62/6298c3575d155f1bc7e497fd/images/08/8d/e2/62/62e28d080f56dbb4de4e128a/ap520.jpg"],"additionalProperty":[{"@type":"PropertyValue","name":"Compatible Inserts","value":"DCMT 11T3"},{"@type":"PropertyValue","name":"ISO Designation","value":"SVJCR 2525"},{"@type":"PropertyValue","name":"Overall Length","value":"150 mm"},{"@type":"PropertyValue","name":"Shank Width","value":"25 mm"},{"@type":"PropertyValue","name":"Shank Height","value":"25 mm"},{"@type":"PropertyValue","name":"Cutting Head Width","value":"32 mm"},{"@type":"PropertyValue","name":"Cutting Direction","value":"Right"},{"@type":"PropertyValue","name":"Cutting Angle","value":"93°"},{"@type":"PropertyValue","name":"Internal Coolant","value":"Yes"},{"@type":"PropertyValue","name":"Weight","value":"0.735 kg"}]},{"@type":"FAQPage","mainEntity":[{"@type":"Question","name":"What inserts fit this holder?","acceptedAnswer":{"@type":"Answer","text":"DCMT 11T3 indexable inserts fit this holder."}},{"@type":"Question","name":"Does the holder support internal coolant?","acceptedAnswer":{"@type":"Answer","text":"Yes, the turning holder features internal coolant."}},{"@type":"Question","name":"What is the ISO designation of the holder?","acceptedAnswer":{"@type":"Answer","text":"The ISO designation is SVJCR 2525."}},{"@type":"Question","name":"What are the key dimensions?","acceptedAnswer":{"@type":"Answer","text":"Overall length 150 mm, shank 25x25 mm, cutting head width 32 mm."}},{"@type":"Question","name":"What cutting angle and direction does it have?","acceptedAnswer":{"@type":"Answer","text":"Right-hand cutting direction with a 93° geometry."}}]},{"@type":"ItemPage","url":"https://metav-shop.de/","dateModified":"2026-04-16T12:00:00+01:00","author":{"@type":"Person","name":"Stephan Bayer","url":"https://www.linkedin.com/in/stephan-bayer/"},"publisher":{"@type":"Organization","name":"Metav Werkzeuge GmbH","url":"https://metav-shop.de","logo":{"@type":"ImageObject","url":"https://files.plytix.com/api/v1.1/file/public_files/pim/assets/57/c3/98/62/6298c3575d155f1bc7e497fd/images/8e/48/c5/69/69c5488eb2b3400ba580741c/logo-metav-1200-675.png","width":1200,"height":675},"address":{"@type":"PostalAddress","streetAddress":"Parkring 45","postalCode":"46446","addressLocality":"Emmerich","addressCountry":"DE"},"telephone":"+49 2822 7131930","email":"info@metav-werkzeuge.com"},"about":[{"@type":"Thing","name":"Turning Holder SVJCR 2525"},{"@type":"Thing","name":"DCMT 11T3 Compatibility"},{"@type":"Thing","name":"Internal Coolant Enabled"}],"mentions":[{"@type":"Thing","name":"M16-IK shank option"},{"@type":"Thing","name":"TA034 u-plate"},{"@type":"Thing","name":"Recommended Torx T15 screwdriver"}]}]}

Turning Holder SDHC for DCMT Indexable Inserts by Teknik Makina The Turning Holder SDHC for DCMT Indexable Inserts is a precision clamping solution for turning applications, designed to secure DCMT 11T3 indexable inserts for reliable metalcutting operations. Teknik Makina Turning Holder SDHCR 2525 for DCMT 11T3 Secure clamping with robust SDHC design 150 mm overall length for standard toolposts Right-hand cutting with 107.5° cutting angle Compact head width 32 mm for versatile access Durable clamping and consistent cutting performance Built for repeatable results, this Turning Holder features the SDHCR 2525 ISO design that delivers stable insert seating and reduced vibration. The holder’s construction supports consistent chip flow and improved surface finish, making it suitable for serial turning tasks. With a focus on repeatability, the design reduces setup times and minimises downtime, ensuring efficient machining across batches. Compatibility with DCMT 11T3 inserts for flexible tooling Engineered specifically for DCMT 11T3 indexable inserts, the holder enables quick insert changes and secure fixation. This compatibility simplifies tooling logistics and allows workshops to use a common insert family across multiple operations. The targeted fit helps maintain cutting geometry and prolongs insert life by ensuring correct seating and pressure distribution during cutting. Compact dimensions for better accessibility and tool life The holder’s compact head width of 32 mm and a tool body of 25 mm x 25 mm allow access to confined areas while maintaining rigidity. Reduced overhang and a 150 mm overall length lower bending moments and extend tool and insert life. For operations where reach and stiffness must be balanced, this design offers improved stability without sacrificing access to tight workpiece features. Designed for workshop reliability and simple integration Manufactured by Teknik Makina, the holder is built to integrate smoothly into standard toolposts and setups. The right-hand cutting orientation and a precise 107.5° cutting angle deliver predictable chip control and repeatable results on common turning materials. For maintenance and replacement planning, the clear ISO designation and robust mounting geometry simplify inventory and procurement. Choose Teknik Makina’s Turning Holder for dependable clamping of DCMT inserts — for expert advice or technical clarification contact METAV Werkzeuge at info@metav-werkzeuge.com or call +49 2822 7131930, WhatsApp +49 170 2837271 Technical Specifications for reliable clamping Bezeichnung: Turning Holder Brand: Teknik Makina SKU: D252TM For Indexable Inserts: DCMT 11T3 Compatible Inserts: DCMT 11T3 Overall Length: 150 mm Weight: 0.738 kg ISO Designation: SDHCR 2525 Secondary Designation: M11 Width: 25 mm Height: 25 mm Cutting Head Width: 32 mm Cutting Direction: Right Cutting Angle: 107.5° GTIN: 4061905153495 Condition: New Availability: In Stock Manufacturer: Teknik Makina, Nolu Sokak, No 9, Selcuklu, Türkei, eMail: info@teknik-makina.com Responsible Person: Metav Werkzeuge GmbH, Parkring 45, 46446 Emmerich, eMail: info@metav-werkzeuge.com FAQ What inserts does the Turning Holder from Teknik Makina accept? The Teknik Makina Turning Holder is designed to accept DCMT 11T3 indexable inserts, ensuring a secure fit and correct cutting geometry for standard turning operations. Is the Turning Holder SDHCR 2525 suitable for right-hand turning only? Yes, the Teknik Makina Turning Holder SDHCR 2525 shown here is specified for right-hand cutting, which aligns with common turning setups that require that orientation. Can the Turning Holder be used in compact toolposts and confined spaces? The compact dimensions and 32 mm cutting head width of the Teknik Makina Turning Holder make it well suited for installations where accessibility and rigidity are both required. Who can I contact for technical questions about the Turning Holder? For technical questions about the Teknik Makina Turning Holder, METAV Werkzeuge offers expert advice — eMail: info@metav-werkzeuge.com, Phone: +49 2822 7131930, WhatsApp: +49 170 2837271. 150mm SDHC Turning Holder for DCMT 11T3 Indexable Inserts, SDHCR 2525, 107.5° - Teknik Makina

Turning Holder SDACR-F for DCMT Indexable Inserts by Teknik Makina The Turning Holder SDACR-F for DCMT Indexable Inserts is a precision toolholder designed for right-hand turning operations with DCMT 11T3 indexable inserts. SDACR 1212 Holder for DCMT 11T3 Inserts 110 mm Overall Length 12 mm Shank Width and Height 90° Cutting Angle, Right-Hand Robust Clamp Design for Secure Retention Secure clamping for consistent machining results Designed for stable insert retention, the SDACR 1212 delivers repeatable performance across medium-duty turning tasks. The precision-machined clamp keeps DCMT 11T3 inserts seated securely, reducing micro-movement that can cause chatter or inconsistent surface finish. This results in improved part accuracy and longer tool life, especially when repeatability and process stability are critical. Compact geometry that fits tight setups With an 110 mm Overall Length and a 12 mm cross-section, this toolholder is suitable for confined toolposts and recessed setups. Its compact dimensions enable closer turret positioning and better access to small-diameter workpieces, allowing workshops to maintain rigidity without sacrificing reach. The compact design supports efficient chip flow and simplifies tool changeover routines. Precision orientation and right-hand operation Engineered with a 90° Cutting Angle and Right-Hand cutting direction, the holder offers predictable cutting geometry for standard turning and facing operations. The fixed angle supports consistent tool engagement and simplifies process planning, so operators can rely on familiar cutting parameters and reduce setup iterations when switching between similar turning jobs. Built for compatibility and easy integration The holder is expressly made for DCMT 11T3 indexable inserts, enabling straightforward integration into existing tooling assortments. ISO designation SDACR 1212 and adapter reference J11-F help technicians identify the correct holder quickly, minimizing downtime during tool changes. The straightforward compatibility reduces inventory complexity and assists in standardising tooling across multiple machines. Target use cases and operator benefits Ideal for shops that require dependable, repeatable turning in medium-precision production, this holder supports machining of rotational components where surface quality and dimensional control matter. The robust clamp design improves insert retention during interrupted cuts, while the holder’s compactness allows its use in tight fixture arrangements—benefits that suit both contract manufacturers and in-house maintenance departments. Secure your machining consistency with the proven clamping reliability of Teknik Makina — choose this Turning Holder to enhance repeatability and machining quality, and contact METAV Werkzeuge for expert advice and support: info@metav-werkzeuge.com, Tel +49 2822 7131930, WhatsApp +49 170 2837271. Turning Holder SDACR-F for DCMT Indexable Inserts Brand: Teknik Makina SKU: D440TM Suitable Inserts: DCMT 11T3 ISO Designation: SDACR 1212 Secondary Designation: J11-F Overall Length: 110 mm Shank Width: 12 mm Shank Height: 12 mm Cutting Head Width: 12 mm Cutting Direction: Right-Hand Cutting Angle: 90° Weight: 0.135 kg Condition: New Availability: In Stock GTIN: 4061905153419 Label: Klemmhalter SDACR 1212 90° DCMT 11T3 Manufacturer: Teknik Makina, Nolu Sokak, No 9, Selcuklu, Türkiye, eMail: info@teknik-makina.com Responsible Person: Metav Werkzeuge GmbH, Parkring 45, 46446 Emmerich, eMail: info@metav-werkzeuge.com FAQ What inserts are compatible with the Turning Holder SDACR 1212 from Teknik Makina? The Turning Holder SDACR 1212 by Teknik Makina is compatible with DCMT 11T3 indexable inserts, designed to accept the standard insert geometry and provide reliable clamping for right-hand turning applications. Can the Turning Holder SDACR-F for DCMT Indexable Inserts be used in tight toolpost arrangements? Yes, the Turning Holder SDACR-F for DCMT Indexable Inserts features an 110 mm overall length and a slim 12 mm cross-section, which makes the holder suitable for compact toolpost setups and limited-space turret positions. Does Teknik Makina offer support or documentation for the SDACR 1212 holder? Teknik Makina supplies technical specifications for the SDACR 1212 holder; for additional guidance or application-specific advice, METAV Werkzeuge provides competent consultation and can be contacted at info@metav-werkzeuge.com or +49 2822 7131930. Is the clamping mechanism on the SDACR 1212 suitable for interrupted cuts? The robust clamp design of the SDACR 1212 Turning Holder from Teknik Makina improves insert retention under variable cutting conditions, making it appropriate for operations that involve interrupted cuts and moderate machining forces. {"@context":"https://schema.org","@graph":[{"@type":"Product","@id":"#D440TM","sku":"D440TM","mpn":"D440TM","gtin13":"4061905153419","name":"Turning Holder SDACR 1212 90° DCMT 11T3","description":"SDACR-F for DCMT indexable inserts; 110 mm overall length; for DCMT 11T3; 90° cutting angle; right-hand; 12x12 mm cross-section; robust clamping design by Teknik Makina.","image":["https://files.plytix.com/api/v1.1/file/public_files/pim/assets/57/c3/98/62/6298c3575d155f1bc7e497fd/images/13/87/1d/64/641d8713eb4c191311cc52d1/d434tm-main.png","https://files.plytix.com/api/v1.1/file/public_files/pim/assets/57/c3/98/62/6298c3575d155f1bc7e497fd/images/2c/7e/de/62/62de7e2c33927e49dbf3272f/d434tm-artikelliste.jpg","https://files.plytix.com/api/v1.1/file/public_files/pim/assets/57/c3/98/62/6298c3575d155f1bc7e497fd/images/cf/7e/de/62/62de7ecf0f56dbb4de4dbf3e/d434tm-technische-zeichnung.jpg"],"additionalProperty":[{"@type":"PropertyValue","name":"For Indexable Inserts","value":"DCMT 11T3"},{"@type":"PropertyValue","name":"ISO Designation","value":"SDACR 1212"},{"@type":"PropertyValue","name":"Alternate Designation","value":"J11-F"},{"@type":"PropertyValue","name":"Overall Length","value":"110 mm"},{"@type":"PropertyValue","name":"Width","value":"12 mm"},{"@type":"PropertyValue","name":"Height","value":"12 mm"},{"@type":"PropertyValue","name":"Cutting Head Width","value":"12 mm"},{"@type":"PropertyValue","name":"Cutting Angle","value":"90°"},{"@type":"PropertyValue","name":"Cutting Direction","value":"right"},{"@type":"PropertyValue","name":"Weight","value":"0.135 kg"}]},{"@type":"FAQPage","mainEntity":[{"@type":"Question","name":"What inserts fit this holder?","acceptedAnswer":{"@type":"Answer","text":"Designed for DCMT 11T3 indexable inserts."}},{"@type":"Question","name":"What is the overall length?","acceptedAnswer":{"@type":"Answer","text":"Overall length is 110 mm."}},{"@type":"Question","name":"What are the cross-section dimensions?","acceptedAnswer":{"@type":"Answer","text":"Width and height are 12 mm x 12 mm."}},{"@type":"Question","name":"What is the cutting angle and direction?","acceptedAnswer":{"@type":"Answer","text":"Cutting angle 90° with right-hand cutting direction."}},{"@type":"Question","name":"Who is the manufacturer?","acceptedAnswer":{"@type":"Answer","text":"Teknik Makina."}}]},{"@type":"ItemPage","url":"https://metav-shop.de/","dateModified":"2026-04-16T12:00:00+01:00","author":{"@type":"Person","name":"Stephan Bayer","url":"https://www.linkedin.com/in/stephan-bayer/"},"publisher":{"@type":"Organization","name":"Metav Werkzeuge GmbH","url":"https://metav-shop.de","logo":{"@type":"ImageObject","url":"https://files.plytix.com/api/v1.1/file/public_files/pim/assets/57/c3/98/62/6298c3575d155f1bc7e497fd/images/8e/48/c5/69/69c5488eb2b3400ba580741c/logo-metav-1200-675.png","width":1200,"height":675},"address":{"@type":"PostalAddress","streetAddress":"Parkring 45","postalCode":"46446","addressLocality":"Emmerich","addressCountry":"DE"},"telephone":"+49 2822 7131930","email":"info@metav-werkzeuge.com"},"about":[{"@type":"Thing","name":"Turning Holder"},{"@type":"Thing","name":"SDACR-F for DCMT Indexable Inserts"},{"@type":"Thing","name":"Teknik Makina Tooling"}],"mentions":[{"@type":"Thing","name":"DCMT 11T3 Inserts"},{"@type":"Thing","name":"SDACR 1212"},{"@type":"Thing","name":"J11-F"}]}]}

Turning Holder (Klemmhalter) SVJCR 2020 for DCMT 11T3 by Teknik Makina The Turning Holder (Klemmhalter) is a right-hand turning tool designed for secure mounting of DCMT 11T3 indexable inserts, suited for precision external turning and finishing operations. For DCMT 11T3 indexable inserts Internal cooling for improved Chip Evacuation 150 mm overall length for enhanced Stability SVJCR 2020 ISO designation for easy Compatibility 93° cutting angle for accurate right-hand Turning Precision and Stability for demanding turning operations The Turning Holder combines a rigid 150 mm Overall Length with a 25 mm Width and 25 mm Height, delivering stable cutting conditions that reduce tool deflection. The 32 mm Cutting Head Width and a 93° Cutting Angle are tuned to provide consistent engagement with the workpiece, yielding improved dimensional accuracy. This stability directly translates into fewer rework cycles and higher first-pass quality, which is particularly relevant for short- to medium-length turning jobs where vibration control matters. Compatibility and clear fit for DCMT 11T3 inserts Engineered for DCMT 11T3 indexable inserts, the holder follows the SVJCR 2020 ISO designation to ensure consistent geometric fit and repeatability across insert changes. The clamping system accepts the specified insert shape and secures it reliably for turning in the right-hand Cutting Direction, simplifying tool setup and minimizing downtime. For workshops standardising on DCMT inserts, this holder streamlines inventory and guarantees predictable cutting behavior. Practical mounting, coolant support and maintenance benefits The holder features Internal Cooling, providing coolant directly to the cutting zone to reduce heat and improve chip control; this helps to extend insert life and maintain surface finish under continuous machining. Assembly uses a Torx T15 interface and an M3.5x11 Torx screw for secure fixation, while the supplied U-Plate (TA034) ensures correct seating of the insert. These elements make routine maintenance straightforward and reduce the risk of incorrect clamping that can damage inserts or affect part quality. Who benefits from this holder and how to integrate it This product targets professional turning shops and precision machine operators seeking a robust solution for finishing and medium-material-removal tasks. The Turning Holder is particularly suitable where repeatable geometry and coolant-through capability are required to stabilise machining processes. Integrating this holder into a standard toolset helps maintain consistent cycle times and improves predictability in production workflows. Choose the Teknik Makina Turning Holder SVJCR 2020 for reliable, coolant-assisted turning — for tailored technical advice or to confirm suitability for your application, contact METAV Werkzeuge at info@metav-werkzeuge.com, phone +49 2822 7131930 or WhatsApp +49 170 2837271. Designation: Turning Holder (Klemmhalter) Brand: Teknik Makina SKU: AP525TM For Indexable Inserts: DCMT 11T3 Compatible Inserts: DCMT 11T3 Overall Length: 150 mm Weight: 0.735 kg ISO Designation: SVJCR 2020 Secondary Designation: K16-IK Width: 25 mm Height: 25 mm Cutting Head Width: 32 mm Cutting Angle: 93° Cutting Direction: Right Internal Cooling: Yes Torx Key: T15 Torx Screw: M3.5x11 U-Plate: TA034 GTIN: 4061905052507 Manufacturer: Teknik Makina, Nolu Sokak, No 9, Selcuklu, Turkey, eMail: info@teknik-makina.com Responsible Person: Metav Werkzeuge GmbH, Parkring 45, 46446 Emmerich, eMail: info@metav-werkzeuge.com FAQ What inserts fit the Turning Holder from Teknik Makina and which designation does it use? The Teknik Makina Turning Holder (Klemmhalter) is designed for DCMT 11T3 indexable inserts and uses the SVJCR 2020 ISO designation to ensure correct geometric compatibility. Does the Turning Holder support coolant-through operation? Yes, the Teknik Makina Turning Holder features internal cooling, which delivers coolant to the cutting zone to improve chip evacuation and can contribute to longer insert life. What tools are required to mount inserts in the SVJCR 2020 holder? Mounting the insert in the Teknik Makina Turning Holder requires a Torx T15 key and the M3.5x11 Torx screw provided; the U-Plate TA034 ensures the insert seats correctly. Is this holder suitable for left-hand turning applications? The Teknik Makina SVJCR 2020 Turning Holder is specified for right-hand cutting direction; for left-hand requirements, please consult METAV Werkzeuge for alternative solutions. Who can I contact for technical advice about integrating the Turning Holder into my tool setup? METAV Werkzeuge offers detailed consultation for the Teknik Makina Turning Holder; contact them at info@metav-werkzeuge.com, phone +49 2822 7131930 or WhatsApp +49 170 2837271 for tailored technical support. {"@context":"https://schema.org","@graph":[{"@type":"Product","@id":"#AP525TM","sku":"AP525TM","mpn":"AP525TM","gtin13":"4061905052507","name":"150mm Turning Holder for DCMT 11T3, 93° Cutting Angle, Internal Cooling - Teknik Makina","description":"Turning holder SVJCR 2020 for DCMT 11T3 indexable inserts; 150 mm overall length, 93° cutting angle, internal cooling, right cutting direction.","image":["https://files.plytix.com/api/v1.1/file/public_files/pim/assets/57/c3/98/62/6298c3575d155f1bc7e497fd/images/08/8d/e2/62/62e28d080f56dbb4de4e128a/ap520.jpg"],"additionalProperty":[{"@type":"PropertyValue","name":"For indexable inserts","value":"DCMT 11T3"},{"@type":"PropertyValue","name":"Overall length","value":"150 mm"},{"@type":"PropertyValue","name":"Cutting angle","value":"93°"},{"@type":"PropertyValue","name":"Internal cooling","value":"yes"},{"@type":"PropertyValue","name":"Direction of cut","value":"right"},{"@type":"PropertyValue","name":"ISO designation","value":"SVJCR 2020"},{"@type":"PropertyValue","name":"Shank designation","value":"K16-IK"},{"@type":"PropertyValue","name":"Width","value":"25 mm"},{"@type":"PropertyValue","name":"Height","value":"25 mm"},{"@type":"PropertyValue","name":"Cutting head width","value":"32 mm"},{"@type":"PropertyValue","name":"Weight","value":"0.735 kg"}]},{"@type":"FAQPage","mainEntity":[{"@type":"Question","name":"What insert type fits this holder?","acceptedAnswer":{"@type":"Answer","text":"Designed for DCMT 11T3 indexable inserts."}},{"@type":"Question","name":"What is the overall length?","acceptedAnswer":{"@type":"Answer","text":"Overall length is 150 mm."}},{"@type":"Question","name":"Does it have internal cooling?","acceptedAnswer":{"@type":"Answer","text":"Yes, the holder features internal cooling."}},{"@type":"Question","name":"What is the cutting angle?","acceptedAnswer":{"@type":"Answer","text":"Cutting angle is 93°."}},{"@type":"Question","name":"Which direction of cut is supported?","acceptedAnswer":{"@type":"Answer","text":"Right cutting direction."}},{"@type":"Question","name":"Who is the manufacturer?","acceptedAnswer":{"@type":"Answer","text":"Manufacturer is Teknik Makina."}}]},{"@type":"ItemPage","url":"https://metav-shop.de/","dateModified":"2026-03-31T12:00:00+01:00","author":{"@type":"Person","name":"Stephan Bayer","url":"https://www.linkedin.com/in/stephan-bayer/"},"publisher":{"@type":"Organization","name":"Metav Werkzeuge GmbH","url":"https://metav-shop.de","logo":{"@type":"ImageObject","url":"https://files.plytix.com/api/v1.1/file/public_files/pim/assets/57/c3/98/62/6298c3575d155f1bc7e497fd/images/8e/48/c5/69/69c5488eb2b3400ba580741c/logo-metav-1200-675.png","width":1200,"height":675},"address":{"@type":"PostalAddress","streetAddress":"Parkring 45","postalCode":"46446","addressLocality":"Emmerich","addressCountry":"DE"},"telephone":"+49 2822 7131930","email":"info@metav-werkzeuge.com"},"about":[{"@type":"Thing","name":"Turning Holder"},{"@type":"Thing","name":"DCMT 11T3 Compatibility"},{"@type":"Thing","name":"Internal Cooling"}],"mentions":[{"@type":"Thing","name":"SVJCR 2020"},{"@type":"Thing","name":"K16-IK Shank"},{"@type":"Thing","name":"TA034 U-plate"}]}]}