High-precision drills for reliable, high-throughput metalworking
Drills provide the fundamental rotating cutting solution for producing accurate cylindrical holes in materials such as structural steel, high-alloy stainless steel, cast iron, non-ferrous metals and engineering plastics, delivering consistent hole quality and extended tool life in CNC machining and turning centres. This category covers everything from classic twist drill made from high-speed steel for general machining to solid carbide drill optimised for high cutting speeds and long run times, offering advanced coatings and internal coolant options for improved heat management. By using optimised point geometries and split points the tools reduce thrust, prevent walking at the start of the cut and ensure superior surface finish, which benefits sectors from general mechanical engineering to automotive component manufacture.
4mm Centre Drill Form A DIN 333 60° Solid Carbide Right-Hand Without Countersink - TECWERK
Take advantage of a solid‑carbide centre drill with a 60° centring angle and wide material compatibility for reliable pilot holes and consistent tool life; order directly via Metav Werkzeuge or consult our technicians for application advice. TECWERK centre drill DIN 333 Form A — Solid carbide, 4.00 mm, 60° A TECWERK centre drill DIN 333 Form A designed for accurate centring and short pilot holes across steels, cast irons and engineered plastics in industrial and workshop environments Solid carbide (VHM), robust and wear-resistant DIN 333 Form A, 60° centring angle Right‑hand cutting for conventional setups Suitable for steels, cast irons and plastics Accurate centring for reliable pilot holes The tool delivers repeatable centring thanks to the DIN 333 Form A geometry and the 60° countersink, which together create a precise starting point for subsequent drilling or turning operations. This geometry reduces run‑out and helps maintain concentricity when producing pilot holes for turning centres or drilling sequences. The short pilot profile stabilises the tool in the spindle or chuck, so the initial hole is true and ready for further machining without additional rework. Long tool life and broad material range Manufactured from solid carbide (VHM), the centre drill offers high wear resistance and thermal stability compared with HSS alternatives. The design supports machining of high‑strength steels, steel castings, grey and hard cast irons, CrNi steels, light and non‑ferrous metals, and fibre‑reinforced plastics and other thermosets. The execution is without protective countersink, which keeps the geometry focused on performance and facilitates sharpening or regrinding strategies in professional shops. Predictable machining parameters for process control The tool is optimised for industrial feed and torque conditions: feed in steel up to 800 N: 0.11 mm/rev offers a reliable starting point for process planning, while the right‑hand cutting orientation suits conventional spindle directions. With a 4.00 mm tip diameter, 56 mm overall length and 10 mm shank, the tool can be held securely in standard collets or chucks; the feed value is a per‑revolution parameter, meaning the workpiece or spindle should advance by 0.11 mm for each spindle rotation under the specified cutting conditions to maintain chip formation and surface quality. Simple integration into production workflows Thanks to the standard DIN 333 form and familiar shank dimension, the centre drill fits seamlessly into existing tool sets and fixtures, reducing setup time and lowering the risk of handling errors. The combination of consistent geometry and solid‑carbide construction ensures fewer tool changes and more uptime, which supports efficient batch production and quality assurance in small to medium series work. Where reproducibility matters, this tool contributes to a smoother process chain and predictable output quality. For precise centring tasks with TECWERK solid‑carbide centre drills, contact Metav Werkzeuge today to discuss suitability, clamping options and process parameters; email info@metav-werkzeuge.com or call +49 2822 7131930 Technical Data SKU: 2000861994NW Manufacturer: TECWERK Product type: Centre drill (Zentrierbohrer) Label: Zentrierbohrer DIN 333 Form A D.4mm VHM re.TECWERK Standard: DIN 333 Form: A Material: Solid carbide (VHM) Execution: without protective countersink Cutting direction: Right‑hand cutting Facts Diameter: 4.00 mm Overall length: 56 mm Shank diameter: 10 mm Countersink angle: 60° Feed in steel up to 800 N: 0.11 mm/rev Packaging unit: 1 Special features DIN 333 Form A geometry 60° countersink Solid‑carbide construction Right‑hand cutting Without protective countersink Suitable for high‑strength steels, steel castings, grey cast iron, hard cast iron Usable on CrNi steels, light and non‑ferrous metals Applicable to fibre‑reinforced plastics and other thermosets FAQ What is the countersink angle of this centre drill? The TECWERK centre drill has a 60° countersink angle in accordance with DIN 333 Form A, which provides a standardised tip for reliable centring. Which materials can the TECWERK centre drill machine? The TECWERK centre drill is suitable for high‑strength steels, steel castings, grey and hard cast irons, CrNi steels, light and non‑ferrous metals, and fibre‑reinforced plastics, as specified for broad workshop and industrial use. What feed and cutting direction are recommended? Recommended reference: feed in steel up to 800 N = 0.11 mm/rev; the tool is right‑hand cutting, so feeds and spindle directions should match standard right‑hand machining setups. What shank size and overall length does the tool have? The centre drill features a 10 mm shank and an overall length of 56 mm, suitable for standard collet chucks and short overhang applications. Is the tool supplied with a protective countersink? The product is delivered without protective countersink (ohne Schutzsenkung), leaving the manufacturer geometry intact for direct use or customised preparation. Manufacturer/Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund
4mm HSS Twist Drill DIN 338 ,short, roll forged, black, Type N - MetavCUT
Twist Drill — Type N short HSS drill, 4 mm, 118°, black, DIN 338, HSS (MetavCUT) The Twist Drill is a short HSS Type N metal drill designed for precise drilling with hand drills and drilling machines in metalworking applications. Short design for enhanced stability and precision HSS material for elasticity and reduced breakage risk Conforms to DIN 338 for short twist drills 118° tip angle for reliable centring in softer metals Suitable for hand drill and drilling machine use Efficient performance through material and geometry This short HSS bit combines material properties and geometry to deliver reliable results when drilling metal. High Speed Steel provides elasticity that reduces the risk of breakage, particularly in small diameters below 6 mm, while the short overall length minimises deflection and vibration. One clear benefit is improved tool life during repetitive production tasks thanks to the balanced combination of material toughness and stable design. Stability and precision for demanding metalwork Conforming to DIN 338, the bit’s reduced overhang increases rigidity and enables more precise hole placement in demanding operations. The Type N normal spiral flute is optimised for machining steel, cast iron and non-ferrous metals, giving consistent chip evacuation and rounder holes. Users who require repeatable accuracy in component manufacture will notice less wobble and fewer rejects when using a short configuration. Practical suitability for common drills and applications Designed for use with a hand drill or drilling machine, the 4 mm diameter and 118° tip angle make this bit versatile for general metalworking and softer materials where reliable centring is beneficial. The short flute length improves control when working on thin sheets or small fixtures. This configuration supports technicians who need a dependable tool for maintenance, prototyping and workshop tasks without sacrificing handling comfort. Clear explanation of technical terms and user guidance The designation Type N refers to the standard spiral geometry for metal drills, offering a compromise between cutting action and chip removal; HSS stands for High Speed Steel, a material suited to many common machining tasks. The 118° tip angle means the point is sharper than a 135° variant, which helps with initial bite and centring on curved or coated surfaces. For users unfamiliar with DIN 338, it simply specifies dimensions and tolerances for short straight-shank twist drills so compatibility and performance are predictable. Strong recommendation: For dependable metal drilling, choose the MetavCUT short HSS Twist Drill for its stability and material properties — METAV Werkzeuge offers expert advice to ensure the right tool choice for each application; contact them by email at info@metav-werkzeuge.com, by phone at +49 2822 7131930 or via WhatsApp at +49 170 2837271 Technical specifications Designation: Twist Drill Brand: MetavCUT SKU: 40040-FDA Diameter: 4 mm Tip angle: 118° Spiral length: 43 mm Overall length: 75 mm Execution: short Type: Type N For drill: Hand drill / Drilling Machine Colour: black Material: HSS (High Speed Steel) Standard: DIN 338 Application: Drills for metal Manufacturer: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What is the Twist Drill from MetavCUT used for? The MetavCUT Twist Drill is primarily used for machining high-strength materials and larger drill diameters in metalworking; its form allows straightforward resharpening and it withstands greater loads, making it suitable for workshop and industrial drilling tasks. Which three drill types are there? The main categories are metal drills, wood drills and stone/concrete drills, and the MetavCUT Twist Drill belongs to the metal drill group designed for machining metals with appropriate cutting geometries.
4mm HSS-E Twist Drill DIN 338 ,short, 5% cobalt-alloyed, Type N - MetavCUT
Twist Drill Type N — short, Ø 4 mm, 135° tip angle, 5% cobalt-alloyed, HSS‑E, DIN 338, fully ground shank — MetavCUT The Twist Drill Type N is a short HSS‑E metalworking drill designed for Drilling Machines, offering improved stability and precise performance when machining hard and alloyed steels. Short design for increased stability 135° tip angle for harder materials 5% cobalt-alloyed for heat resistance Fully ground shank for high concentricity Conforms to DIN 338 for standardised dimensions Stable, precise drilling even in hard materials A short Twist Drill made of HSS‑E combines rigidity and wear resistance to reduce vibration and improve hole quality. The reduced overhang of the short execution limits bending and delivers consistent concentricity, which means cleaner holes and longer tool life when working with alloyed and unalloyed steel. The 135° tip angle is tuned to penetrate harder materials with less walking at the start, improving process reliability in demanding metalworking jobs. Material and geometry that add real value The use of 5% cobalt‑alloyed HSS‑E gives this drill enhanced red hardness and thermal stability, reducing wear at elevated cutting temperatures. A fully ground shaft and flute geometry ensure sharp cutting edges and excellent runout accuracy, which benefits precision assemblies and reaming-sensitive operations. For users who need tools that are easy to resharpen and that maintain edge geometry under load, this construction is a practical choice. Designed to match industrial standards and applications Manufactured to DIN 338, this short Twist Drill Type N is suited for standard metalworking set-ups on portable and stationary drilling equipment. The Type N spiral is the conventional choice for metal drilling, delivering controlled chip removal and a balance between cutting speed and surface finish. Typical applications include drilling in steel, cast iron, non-ferrous metals and many engineering plastics where a robust, general-purpose metal drill is required. Practical notes for users and support For drilling below 6 mm diameter, the short form factor reduces breakage risk and is especially useful when machining with minimal clamping or on smaller workpieces. If uncertain whether this Twist Drill Type N matches a specific machine or material condition, METAV Werkzeuge provides expert guidance and supplementary technical data to help select the right tool and operating parameters. Contact options are available for tailored advice and application support. Strong recommendation: Choose the MetavCUT Twist Drill Type N for reliable precision in metal machining — for application help or additional technical data contact METAV Werkzeuge by eMail: info@metav-werkzeuge.com, Phone: +49 2822 7131930 or WhatsApp: +49 170 2837271 Designation: Twist Drill Brand: MetavCUT SKU: 47040-FDA Diameter: 4 mm Tip angle: 135° Type: Type N Material: HSS‑E (5% cobalt‑alloyed) Execution: short Spiral length: 43 mm Overall length: 75 mm Shank execution: fully ground Conforms to: DIN 338 Intended use: Drills for metal Model series: Standard Line For use in: Drilling Machine Packaging unit: 10 Manufacturer: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ For what is a Twist Drill used? A Twist Drill Type N from MetavCUT is primarily applied when machining high‑strength materials and larger drill diameters; its geometry is easy to resharpen and it withstands higher loads, making it suitable for demanding metal drilling tasks and for materials where increased toughness and heat resistance are required. Which three drill types exist? Common categories are Metal drill (such as the MetavCUT Twist Drill Type N), Wood drill, and Masonry/Concrete drill; each group is optimised in geometry and material to perform best in its respective material class.
4mm HSS-G Body Drill ,double sided, black finished without margin - MetavCUT
Karosseriebohrer »59040-FDA« von MetavCUT Karosseriebohrer »59040-FDA« ist ein geschliffener HSS-G Doppelendbohrer für präzise Blech- und Karosseriearbeiten mit 4 mm Durchmesser. Karosseriebohrer »59040-FDA« von MetavCUT HSS-G geschliffen für saubere Metallbohrungen Doppelendbohrer: beidseitig einsetzbar 4 mm Durchmesser, Spiralänge 13 mm Spitzenwinkel 135° für harte Werkstoffe Hervorragende Schneidleistung dank geschliffener HSS-G-Geometrie Der geschliffene HSS-G Werkstoff sorgt für sehr scharfe Schneiden und eine hohe Rundlaufgenauigkeit, was saubere und präzise Bohrlöcher in Stahl, Guss und Nichteisenmetallen ermöglicht. Durch den CNC-Schliff entstehen definierte Spanräume, die das Bohren erleichtern; in der Praxis führt das zu einem bis zu 40 % schnelleren Vorschub bei gleichzeitig bis zu 50 % reduzierter Anpresskraft gegenüber ungeschliffenen Varianten. Für stationäre Anwendungen und den Einsatz mit Kühlschmierstoff bietet die Geometrie die besten Ergebnisse. Vielseitiger Einsatz im Werkstattalltag und bei Karosseriearbeiten Als Doppelendbohrer konzipiert, lässt sich das Werkzeug beidseitig verwenden und verlängert so die Nutzungsdauer pro Werkzeug. Mit 4 mm Durchmesser und einer Spiralänge von 13 mm eignet sich der Bohrer besonders für Bohrungen in Blech sowie für Niet- und Dünnblechanwendungen, wie sie in der KFZ-Karosserie vorkommen. Im Segment von 2 mm bis 13 mm ist dieser Bohrertyp ideal für handgeführte Werkzeuge wie die Handbohrmaschine, solange bei hoher Präzision vorher ein Zentrierpunkt gesetzt wird. Anwendungshinweise für saubere Ergebnisse und lange Standzeit Vor dem ersten Einsatz empfiehlt sich das Anpunkten mit einem Zentrierstift, um Wandern auf der Oberfläche zu vermeiden und exakte Bohrungen zu erzielen. Bei härteren Werkstoffen zahlt sich der 135° Spitzenwinkel aus, da dieser die Anbohrzeit verkürzt und das Einlaufen erleichtert. Wegen der geschliffenen Ausführung ist auf kontrollierte Drehzahl und Kühlung zu achten; die Bohrer können bei falscher Handhabung spröde reagieren. Regelmäßiges Reinigen der Spannuten und sachgerechtes Lagern verlängern die Standzeit deutlich. Für wen dieser Bohrer entwickelt wurde und was er bringt Der Bohrer richtet sich an Karosserie- und Blechbearbeiter, Mechaniker sowie anspruchsvolle Heimwerker, die saubere, wiederholbare Ergebnisse verlangen. Die Kombination aus geschliffener HSS-G-Geometrie und Doppelend-Ausführung bietet sowohl Wirtschaftlichkeit als auch Leistungsfähigkeit in Werkstätten und bei mobilen Einsätzen. MetavCUT liefert mit der Profi Line ein Werkzeug, das Robustheit und Präzision verbindet und sich besonders in wiederkehrenden Montage- und Reparaturaufgaben bewährt. MetavCUT empfiehlt den geschliffenen HSS-G Karosseriebohrer 59040-FDA für präzise Karosserie- und Blecharbeiten; bei Fragen zur Anwendung oder Lieferung erreichen Sie uns per eMail: info@metav-werkzeuge.com oder telefonisch unter +49 2822 7131930 Produktmerkmale Artikelnummer: 59040-FDA Hersteller: MetavCUT Bezeichnung: Karosseriebohrer Serie: Profi Line Fakten Durchmesser: 4 mm Gesamtlänge: 55 mm Spiralänge: 13 mm Spitzenwinkel: 135° Verpackungseinheit: 10 Besonderheiten Material: HSS-G (geschliffen) Ausführung: doppelseitig Schaftausführung: geschliffen Farbe: schwarz ohne Fase Für Bohrmaschine: Handbohrmaschine Modellserie: Profi Line FAQ Für welche Materialien ist der Bohrer geeignet? Der Karosseriebohrer von MetavCUT eignet sich für legierten und unlegierten Stahl, Gussstahl, Gusseisen, Sintereisen, Temperguss sowie Nichteisenmetalle und Hartkunststoffe; die geschliffene Geometrie der Profi Line sorgt für saubere Bohrbilder auch in härteren Werkstoffen. Kann der Bohrer mit einer Handbohrmaschine verwendet werden? Ja, die Ausführung mit 4 mm Durchmesser und geschliffenem Schaft ist für den Einsatz in Handbohrmaschinen geeignet; für hochpräzise Bohrungen empfiehlt sich das Anpunkten mit einem Zentrierstift, wie es für Bohrer im Standard-Bereich empfohlen wird. Wie tief kann mit diesem Bohrer gebohrt werden? Die nutzbare Spiralänge von 13 mm begrenzt die sinnvolle Bohrtiefe; die Gesamtlänge von 55 mm erlaubt zudem die Handhabung und das sichere Einspannen, ohne die Einsatzlänge zu überschreiten. Was bedeutet 'geschliffen' und 'HSS-G' in der Praxis? Geschliffen bedeutet, dass die Schneiden und Spannuten per CNC-Schliff geformt wurden, was zu schärferen Kanten, besserem Rundlauf und präziseren Bohrlöchern führt; HSS-G steht für High-Speed-Stahl geschliffen und bringt dadurch höhere Schnittgeschwindigkeit, allerdings ist bei unsachgemäßer Anwendung auf mögliche Sprödigkeit und Kühlung zu achten. Worauf ist beim Bohren in Karosserieblech besonders zu achten? Bei dünnen Blechen empfiehlt sich geringerer Vorschub und schnelles Drehen, ein Zentrierpunkt schützt vor Wandern, und die doppelseitige Bauweise ermöglicht ein schnelles Umdrehen, wenn eine Seite stumpf wird, wodurch Stillstandzeiten reduziert werden.
4mm HSS-G Body Drill ,double sided, bright finished - MetavCUT
Karosseriebohrer (Body Drill) — Twist Drill, 4 mm, 135°, Double-sided, Bright Finished, Fully Ground, HSS-G A Karosseriebohrer (Body Drill) designed as a double-sided Twist Drill for precise metalworking with a 4 mm diameter and a 135° point angle, suitable for hand Drilling Machines and industrial use MetavCUT Body Drill for metal applications 4 mm Diameter for accurate pilot holes 135° Point Angle for harder materials Double-sided design offers two usable tips Fully ground HSS-G for clean, precise holes Durable HSS-G construction for demanding metalwork The fully ground HSS-G material ensures a sharp cutting geometry and high roundness accuracy, which produces clean holes in a wide range of metals. Because the flutes are produced by CNC grinding rather than by rolling, the bit achieves very precise cutting edges that reduce burr formation and improve hole quality. This design is particularly advantageous when working with legierte and unlegierte Stahl, Gussstahl and other hardened materials where a stable, sharp tip matters for consistent results. Faster drilling with lower force and reliable centring Thanks to the double-sided design and the ground geometry, this Twist Drill requires noticeably less feed force and delivers accelerated penetration compared with conventional bits. The reduced thrust demand and the optimized point geometry mean that drilling can be performed up to 40 % faster while needing less operator pressure, making repetitive tasks easier and reducing operator fatigue. The 135° point angle improves centring and performance in harder materials while lowering the risk of walking on the workpiece. Practical design for metalworking workshops and on-site jobs The short, robust shape of this double-ended twist drill makes it ideal for bodywork, sheet-metal and rivet-hole preparation where stability and repeatable hole quality are essential. The bright finished surface improves visibility of the cutting edges, and the fully ground shaft provides excellent runout and seating in chucks. Compatibility with standard hand Drilling Machines means this bit is versatile for both stationary and portable setups, offering dependable results across workshop and field applications. Who benefits from this Body Drill and how to use it effectively Craftspeople, maintenance technicians and metal fabricators will appreciate the combination of precision and practical durability. When machining cast parts, tempered steels or high-strength alloys, using coolant and a steady drill speed suited to the material will extend tool life. The double-ended Twist Drill can be reversed once one tip is dulled, effectively giving two usable cutting tips per tool and improving cost efficiency for repetitive drilling tasks. If you need personalised guidance whether this MetavCUT Karosseriebohrer meets your exact requirements or require additional technical data, METAV Werkzeuge offers expert advice — eMail: info@metav-werkzeuge.com — Phone: +49 2822 7131930 — WhatsApp: +49 170 2837271 Technical specifications Designation: Body Drill / Karosseriebohrer Brand (Marke): MetavCUT SKU: 58040-FDA Diameter: 4 mm Point Angle: 135° Overall Length: 55 mm Spiral Length: 13 mm Execution / Type: Double-sided (doppelseitig) Shaft Finish: Fully ground (geschliffen) Material: HSS-G Colour: Bright finished (blank) Suitable for: Drilling Machine / Hand Drilling Machine Model Series: Standard Line Application: Drills for metal / Twist Drill Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What are Twist Drills used for? Twist Drills like the MetavCUT Karosseriebohrer (Body Drill) are primarily used for machining high-strength materials and larger drill diameters; their shape allows straightforward sharpening and they withstand greater loads, making them suitable for tasks such as creating holes in sheet metal and structural components. Which three drill types exist? Commonly distinguished drill types are metal drill, wood drill and stone/concrete drill; the MetavCUT Karosseriebohrer is designed as a metal drill (Twist Drill) optimised for steel and non-ferrous metals. Why are Twist Drills re-sharpened at the tip? Re-sharpening reduces the cross cutting edge at the tip, which lowers friction and the feed forces required; this results in better centring of the MetavCUT Karosseriebohrer and improved drilling performance in demanding materials. Can a metal Twist Drill be used in wood? A metal drill such as the MetavCUT Karosseriebohrer can be used in wood, but guidance is reduced and finish quality may be lower; however, these bits are easier to re-sharpen and exhibit less self-feeding compared with specialised wood bits.
4mm HSS-G Twist Drill DIN 1869 ,extra long, bright finished - MetavCUT
Twist Drill — Twist Drill, 4 mm, 135°, HSS-G, DIN 1869, bright finished, extra long An Twist Drill designed as an extra-long HSS‑G metal drill for deep, precise holes with a 135° point angle suitable for drilling machines. Extra-long design for deep drilling 135° point for hard materials HSS‑G ground for faster metal drilling Fully ground shank for high runout accuracy Complies with DIN 1869 standard Fast, precise performance in demanding metalwork Der Twist Drill aus HSS‑G verbindet hohe Schnittschärfe mit belegter Leistungssteigerung: Gezielt geschliffene Geometrien ermöglichen bis zu 40% schnellere Bohrfortschritte und reduzieren die erforderliche Anpresskraft um 50% gegenüber konventionellen HSS‑Bohrern. Der 135° Spitzenwinkel ist speziell auf härtere Werkstoffe abgestimmt und verringert das Wanderverhalten beim Anbohren. Diese Kombination sorgt für saubere, präzise Bohrlöcher in legierten und unlegierten Stählen sowie in Gusswerkstoffen bis 1000 N/mm². Extra length for deep holes and restricted access Dank der extra long Ausführung mit einer Spiralänge von 120 mm und einer Gesamtlänge von 175 mm ist dieser Bohrer ideal, wenn Tiefe oder schwer zugängliche Positionen gefordert sind. Die helle Oberfläche (bright finished) unterstützt das einfache Einführen und Sichtbarkeit beim Einspannen. Konzipiert für den Einsatz in der Drilling Machine, bietet die verlängerte Bauform Nutzen bei Taschenbohrungen, Durchbohrungen größerer Bauteile und bei Anwendungen, wo herkömmliche Längen nicht ausreichen. Ground geometry, handling and application tips Die geschliffene Ausführung (HSS‑G, fully ground) sorgt für sehr scharfe Schneiden sowie hohe Rundlaufgenauigkeit; dies begünstigt exakte Bohrbilder in harten Werkstoffen. Gleichzeitig ist die gefräste/geschliffene Geometrie empfindlicher gegen Überlast und sollte bevorzugt stationär und mit Kühlschmierstoff verwendet werden, um Bruchrisiken zu minimieren. Für Anwender bedeutet das: Höhere Präzision bei professioneller Bearbeitung, mit dem Hinweis auf vorsichtigen Einsatz in mobilen, ungekühlten Anwendungen. For deep, precision metal drilling, choose the MetavCUT Twist Drill in HSS‑G extra‑long execution — Metav Werkzeuge provides comprehensive, expert consultation and technical support via info@metav-werkzeuge.com, Tel +49 2822 7131930 or WhatsApp +49 170 2837271 Technical Data Designation: Twist Drill, 4 mm, extra long, bright finished Marke: MetavCUT SKU: 32040-FDA Diameter: 4 mm Point angle: 135° Spiral length: 120 mm Overall length: 175 mm Material: HSS-G Standard: DIN 1869 Shank finish: Fully ground Colour: Bright finished For machine: Drilling Machine Execution: extra long Model series: Standard Line Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ For what is a Twist Drill used? The MetavCUT Twist Drill is primarily applied for machining high‑strength materials and large hole diameters. Its ground geometry is easy to resharpen and withstands higher loads, making it suitable for robust metalworking tasks and deep drilling under demanding conditions. Which three drill types exist? Commonly differentiated drill types are metal drills, wood drills, and stone/concrete drills; the MetavCUT Twist Drill belongs to the metal drill category and is optimised for metallic materials.
4mm HSS-G Twist Drill DIN 1869 ,extra long, bright finished - MetavCUT
Kombinieren Sie Geschwindigkeit, Präzision und Extra-Länge für tiefe Metallbohrungen; Bestellen Sie den MetavCUT HSS-G Spiralbohrer 4 mm extra lang direkt über Metav oder nutzen Sie die technische Beratung bei Bedarf. Spiralbohrer 4 mm HSS-G »Standard Line« extra lang von MetavCUT Der Spiralbohrer 4 mm HSS-G extra lang ist für präzise Metallbohrungen konzipiert und eignet sich besonders für tiefe oder schwer zugängliche Bohrungen mit 135° Spitzenwinkel. 4 mm HSS-G, extra lang für tiefe Bohrungen Gesamtlänge 220 mm, Spiralänge 150 mm Geschliffener Schaft für hohe Rundlaufgenauigkeit DIN 1869 Tieflochspirale für erschwerte Bedingungen Spitzenwinkel 135° für harte Werkstoffe Schnelle und präzise Bearbeitung auch in harten Werkstoffen Der geschliffene HSS-G Spiralbohrer reduziert den Anpressdruck deutlich und ermöglicht ein bis zu 40 % schnelleres Bohren bei gleichzeitig bis zu 50 % geringerer Anpresskraft im Vergleich zu herkömmlichen HSS-Bohrern. Die geschliffene Geometrie sorgt für scharfe Schneiden und saubere Spanabfuhr, was die Qualität der Bohrung erhöht und Nacharbeit reduziert. Das führt zu messbaren Zeitgewinnen in Werkstatt und Produktion. Stabilität und Rundlaufgenauigkeit für stationäre Anwendungen Der voll geschliffene Schaft bietet hohe Rundlaufgenauigkeit und eignet sich daher besonders für stationäre Bohrmaschinen und präzise Spannvorrichtungen. Der Spitzenwinkel 135° verbessert das Anbohrverhalten in harten Werkstoffen und verringert das Wandern beim Ansetzen. Wegen der geschliffenen Fertigung ist auf ausreichende Kühlung und geeignete Spannmittel zu achten, damit die Standzeit maximiert und Bruchrisiken minimiert werden. Passende Einsatzbereiche und Maschinentypen für den Standard-Bereich Mit einem Durchmesser von 4 mm fällt der Bohrer in den Standard-Bereich und ist ideal für Werkstatt, Montage und DIY-Projekte. Er eignet sich zum Bohren in legierten und unlegierten Stahl, Gussstahl, Gusseisen, Temperguss, Nichteisenmetallen und Hartkunststoff. Die extra Gesamtlänge 220 mm und die Spiralänge 150 mm erlauben tiefe Bohrungen und den Zugriff in schwer erreichbaren Zonen ohne aufwendiges Umspannen. Wirtschaftlichkeit, Lieferumfang und Produktionsnutzen Die Ausführung als extra lang in der Serie Standard Line macht mehrere Arbeitsgänge überflüssig und reduziert Rüstzeiten. Die Verpackungseinheit von 10 Stück sichert die Versorgung kleiner Serien und Reparaturaufträge ohne ständigen Nachkauf. Als Produkt von MetavCUT lässt sich der Bohrer gut in vorhandene Fertigungsprozesse integrieren und trägt zur Produktivitätssteigerung durch konstante Bohrbildqualität bei. Mit dem MetavCUT HSS-G Spiralbohrer 4 mm extra lang Präzision sichern – Beratung und Bestellabwicklung direkt bei Metav: info@metav-werkzeuge.com, ☎️ +49 2822 7131930 Produkteigenschaften Artikelnummer: 33040-FDA Marke: MetavCUT Bezeichnung: Spiralbohrer Serie: Standard Line Fakten Durchmesser: 4 mm Gesamtlänge: 220 mm Spiralänge: 150 mm Spitzenwinkel: 135° Verpackungseinheit: 10 Besonderheiten Material: HSS-G (geschliffen, hohe Rundlaufgenauigkeit) Norm: DIN 1869 (Tieflochspirale für extra tiefe Bohrungen) Schaftausführung: geschliffen (fully ground) Ausführung: extra lang (verlängerte Arbeits- und Gesamtlänge) Für Bohrmaschine: Handbohrmaschine (geeignet für Standard-Bereich) Farbe: blank FAQ Für welche Materialien ist der Spiralbohrer geeignet? Der MetavCUT Spiralbohrer 4 mm HSS-G ist für legierten und unlegierten Stahl, Gussstahl, Gusseisen, Temperguss, Nichteisenmetalle und Hartkunststoff ausgelegt und bietet bei diesen Werkstoffen eine hohe Bohrqualität. Ist der Bohrer für Handgeführte Maschinen geeignet? Ja, der Spiralbohrer 4 mm fällt in den Standard-Bereich und kann mit Handgeführten Akkubohrschraubern eingesetzt werden; für maximale Präzision empfiehlt sich jedoch eine stationäre Aufnahme oder Zentrierung vor dem Bohren. Wie tief lassen sich Löcher mit dem extra langen Bohrer realisieren? Die Extra-Länge mit Spiralänge 150 mm erlaubt deutlich tiefere Bohrungen als Standardausführungen; bei sehr tiefen Lagen sind Zwischenkühlungen und mehrstufiges Aufbohren zu beachten. Welche Vorteile bringt der geschliffene Schaft konkret? Der geschliffene Schaft sorgt für scharfe Schneiden und hohe Rundlaufgenauigkeit, was saubere Bohrlöcher, geringeren Verschleiß an Spannmitteln und reproduzierbare Ergebnisse in der Fertigung ermöglicht. Was bedeutet die Norm DIN 1869 bei diesem Bohrer? DIN 1869 steht für eine Tieflochspirale, die speziell für extra tiefe Bohrungen und erschwerte Spanabfuhr konzipiert ist; beim MetavCUT Spiralbohrer unterstützt dies stabile Spanabfuhr und saubere Bohrbilder.
4mm HSS-G Twist Drill DIN 1869 ,extra long, bright finished - MetavCUT
Twist Drill — Extra long HSS‑G Drill Bit for Metal (4 mm, 135°) The Twist Drill is an extra‑long HSS‑G drill bit designed for deep metal drilling with a 4 mm diameter and a 135° tip angle, suitable for use in drilling machines and stationary equipment. Extra‑long HSS‑G design for deep drilling 4 mm diameter with 135° tip for hard metals Fully ground shank for high concentricity DIN 1869 standard for deep hole performance Bright finish for improved chip evacuation Superior Material for Demanding Metalwork The Twist Drill is manufactured from HSS‑G, providing high red hardness and wear resistance for demanding tasks. The combination of the DIN 1869 geometry and a 135° tip angle makes this bit particularly effective in harder materials, reducing chatter and improving centring when entering tough surfaces. The construction gives reliable hole quality and consistent performance in legated and unlegated steels, cast iron and non‑ferrous metals. Made for Deep, Hard‑to‑Reach Holes With a Total Length of 280 mm and a Spiral Length of 190 mm, this extra‑long design enables drilling far beyond standard reach, ideal for deep bore requirements or operations where access is restricted. The extended working length minimises the need for extensions and permits cleaner chip removal over long depths. For deep metal bores, the geometry supports sustained performance while maintaining hole straightness. Precision Finish and Easier Cutting A fully ground shank and CNC‑ground flutes ensure sharp cutting edges and superior runout, delivering precise holes and smooth chip flow. The bright finish reduces friction and aids chip evacuation during drilling. Compared with rolled HSS variants, the ground geometry allows up to 40% faster drilling and demands 50% less feed force, which translates to less operator effort and more efficient cycles on stationary or machine drills. Recommended Applications and Safe Use This Twist Drill is optimised for drilling in metal, including alloyed steels, cast steels and hard plastics. Due to the ground geometry, the bit is best used in machine or drill press environments with appropriate cooling; ground HSS can be more brittle than rolled designs and benefits from coolant and moderate feed rates to avoid breakage. For non‑industrial handheld use, verify machine stability and apply reduced feed to protect the tool. Who Benefits Most Workshops and professionals who need accurate deep holes in tougher materials will appreciate the combination of extra reach and precision. The bit suits machine shops, toolrooms and maintenance departments that require reproducible hole quality and longer working lengths without sacrificing centring performance. MetavCUT’s Standard Line targets users who prioritise precision and consistent results. We recommend the MetavCUT extra‑long Twist Drill for precision deep metal drilling — for competent advice and tailored technical support contact METAV Werkzeuge at info@metav-werkzeuge.com, phone +49 2822 7131930 or WhatsApp +49 170 2837271 Designation: Twist Drill (Spiralbohrer) Brand: MetavCUT SKU: 34040-FDA Diameter: 4 mm Tip Angle: 135° Material: HSS‑G Standard: DIN 1869 Execution: extra long Total Length: 280 mm Spiral Length: 190 mm Shank Finish: fully ground (geschliffen) Colour/Finish: bright finished (blank) For Use With: Drilling Machine (Handbohrmaschine) Application: Drills for metal (Bohrer für Metall) Model Series: Standard Line Packaging Unit: 10 Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What materials is the Twist Drill by MetavCUT best suited for? The MetavCUT Twist Drill is primarily designed for metalworking and performs well in alloyed and unalloyed steels, cast steel, cast iron and non‑ferrous metals; its HSS‑G composition and 135° tip help when machining harder materials and improve centring and hole quality. How does the extra‑long execution improve drilling performance? An extra‑long Twist Drill provides a greater overall and working length, allowing deeper bores without extensions; this is beneficial for long‑reach operations and restricted access, while the spiral geometry supports consistent chip evacuation over the full drilling depth. For what is a Twist Drill used? A Twist Drill is mainly applied to the machining of high‑strength materials and larger drill diameters; its shape is easy to re‑grind and it withstands significant loads while providing good centring and cutting behaviour. Which three drill types are there? Common categories include metal drills, wood drills and masonry/concrete drills. Why are Twist Drills sharpened (ausgespitzt)? Sharpening reduces the cross‑edge at the tip of the Twist Drill, which lowers friction and thus requires less feed force; at the same time the tip centres better in the workpiece and improves drilling accuracy. Can a metal Twist Drill be used for wood? A metal drill can be used in wood, but guidance and surface finish will usually be inferior compared with dedicated wood drills; metal drills are easier to re‑grind and typically have less self‑feed than specialised wood drills. For which drilling depths is the Twist Drill most used? A solid bore is commonly executed with a Twist Drill. For diameters up to 20 mm and depths up to 100 mm, the Twist Drill is the most frequently used tool. Is HSS or HSSE better? The general belief that HSSE steels are categorically superior to HSS is incorrect; when choosing, evaluate whether your working conditions justify the higher cost of HSSE for your specific application.
4mm HSS-G Twist Drill DIN 1897 ,extra short, bright finished, Type N - MetavCUT
MetavCUT Twist Drill — 4 mm, 135° Tip, Type N, Bright Finished, Extra Short, DIN 1897, HSS‑G The MetavCUT Twist Drill is an extra short Type N drill bit designed for precise metalworking with Drilling Machines and Hand Drills, offering stable performance in confined spaces. Extra short design for greater stability 135° tip angle for harder materials Cylindrical shank for universal chuck fitting Made from HSS‑G for durable, fast drilling Conforms to DIN 1897 for consistent dimensions High Stability and Faster Penetration for Metalworking The extra short geometry of this Twist Drill reduces overall length and cutting length, which increases stability and reduces the risk of breakage when working in tight or thin components. The ground HSS‑G cutting edges enable up to 40% faster drilling with approximately 50% less axial force compared with conventional HSS drills, so operators can achieve cleaner holes with less exertion. This makes the bit particularly suitable for repetitive metalworking tasks where tool life and operator comfort matter. Secure Cutting in Tough Materials Thanks to 135° Tip A 135° tip angle tailors the MetavCUT Twist Drill to harder workpiece materials such as alloyed and unalloyed steels, cast steels and other dense metals. The blunter tip reduces initial cutting forces and shortens the time to penetrate the surface, improving centering and reducing walking on stainless steel or tempered iron. For customers less familiar with geometry: a larger tip angle spreads the contact area and delays dulling, which keeps hole quality consistent over longer runs. Universal Compatibility with Cylindrical Shank and Standard Norms Equipped with a cylindrical (round) shank, the Twist Drill clamps easily in standard three‑jaw chucks of Hand Drills and Drilling Machines, delivering a simple and universal fit. Conformity to DIN 1897 ensures predictable overall and flute lengths for tool planning and replacement. Note that while the round shank is widely compatible, under very high torque conditions a chuck may allow slight slippage compared with polygonal shanks. Practical Use Cases and Who Benefits Most This Twist Drill is aimed at professionals and well‑equipped hobbyists who work with metal, such as fabricators, maintenance technicians and toolroom operators. It excels in drilling into sheet metal, profiles, castings and harder grades of steel where short overhang and robust performance are required. For thin‑walled components or cramped setups the extra short format improves control and reduces chatter, producing cleaner bores with less rework. Handling Tips and Best Practices When using the MetavCUT Twist Drill, apply moderate cutting speeds suited to HSS‑G in metals and use cutting fluid where applicable to extend tool life and improve finish. A light pilot or centre punch helps to prevent walking on smooth surfaces. Because the bit is extra short, avoid excessive overhang from the chuck—keep the working length as short as practical to retain the stability advantages. For demanding professional metalwork choose the MetavCUT Twist Drill for reliable, high‑performance results — METAV Werkzeuge offers expert advice and technical support at info@metav-werkzeuge.com, by telephone on +49 2822 7131930 or via WhatsApp at +49 170 2837271 Twist Drill Marke: MetavCUT SKU: 56040-FDA Diameter: 4 mm Tip angle: 135° Type: Type N Colour: Bright finished Execution: Extra short Material: HSS‑G Shaft execution: Cylindrical Spiral length: 22 mm Overall length: 55 mm Suitable for: Drilling Machine / Hand Drill Model series: Standard Line Application: Drills for metal Norm: DIN 1897 Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What materials is the MetavCUT Twist Drill suitable for? The MetavCUT Twist Drill is designed primarily for metalworking and performs well in alloyed and unalloyed steel, cast steel, cast iron, sintered iron, non‑ferrous metals and hard plastics; its HSS‑G composition and Type N spiral make it a reliable choice for tougher materials. How should the MetavCUT Twist Drill be used to avoid breakage? Use the MetavCUT Twist Drill with minimal overhang, appropriate cutting speeds for HSS‑G, and cutting fluid where recommended; a centre punch for starting and moderate feed rates help maintain hole quality and reduce the risk of breakage. What is a Twist Drill used for? A Twist Drill, such as the MetavCUT Twist Drill, is primarily applied to machining high‑strength materials and larger hole diameters; its form is easy to regrind and it withstands high loads, making it suitable for demanding metal drilling tasks. Which 3 drill types are there? The three principal drill categories are metal drills (like the MetavCUT Twist Drill), wood drills, and stone/concrete drills.
4mm HSS-G Twist Drill DIN 338 ,fully ground, silver - MetavCUT
MetavCUT Twist Drill — Twist Drill, 4 mm, 118° Point, HSS‑G, Fully Ground, Silver, Hex Shank, DIN 338 The Twist Drill by MetavCUT is a precision metal‑working drill bit designed for handheld and machine drilling, ideal for accurate holes in alloyed and unalloyed steels and other hard materials. Fully ground HSS‑G for clean holes and high precision 4 mm diameter for fine, accurate drilling 118° point angle for easy centring in softer metals Hexagonal shank for secure fit in bit holders Conforms to DIN 338 for standardised short twist drills Faster metal drilling with sharp, fully ground HSS‑G The HSS‑G construction and fully ground geometry mean this Twist Drill cuts with very sharp edges and excellent concentricity. For the user, that translates into up to 40% faster drilling and reduced feed force, which is particularly beneficial when working on alloyed and unalloyed steel, cast materials or hard plastics. Because the flute geometry is formed by CNC grinding rather than rolling, the hole finish is cleaner and tolerances are tighter, making the bit suited to precision tasks in workshop environments. Reliable centring and torque transmission for handheld work With a 4 mm diameter and a 118° point angle, this twist drill is tailored for applications where straightforward centring and controlled entry are needed. The hexagonal shank (suitable for 1/4" E6.3 holders) prevents slippage and enables rapid tool changes in quick‑change chucks and cordless drivers, while still being compatible with standard drill chucks. Compliance with DIN 338 ensures familiar dimensions and short‑length specifications for effective use on both stationary machines and hand drills. Practical handling, care and performance tips To get the best from this MetavCUT twist drill, use appropriate coolant or cutting fluid during prolonged or stationary machining to reduce heat and lower the risk of brittle failure inherent to very sharp ground drills. The bit is straightforward to resharpen when needed; its geometry lends itself to simple grinding while preserving the original cutting angles. For hobbyists and professionals alike, this results in consistent hole quality and predictable tool life when recommended speeds and feeds are observed. Recommended users and typical applications This twist drill is aimed at metalworkers, maintenance technicians and precision hobbyists who require clean, accurate holes in demanding materials. The Standard Line model combines workshop robustness with quick‑change convenience, making it suitable for repair work, fixture installations and prototype production. If in doubt whether this MetavCUT HSS‑G bit meets specific project requirements, expert advice is available from METAV Werkzeuge to ensure the right tool choice and machining parameters. Strong recommendation: Choose the MetavCUT HSS‑G Twist Drill for demanding metalwork and contact METAV Werkzeuge for personalised technical advice — 📧 info@metav-werkzeuge.com — ☎️ +49 2822 7131930 — ✔️ WhatsApp +49 170 2837271 Twist Drill Marke: MetavCUT SKU: 57040-FDA Diameter: 4 mm Total length: 95 mm Spiral length: 44 mm Point angle: 118° Material: HSS‑G Execution: fully ground Colour: silver For use with: Drilling Machine (Hand drill compatibility) Shank type: hexagonal (E6.3 / 1/4") Model series: Standard Line Norm: DIN 338 Applications: Drills for metal Shaft execution: sechskant Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ Can the MetavCUT Twist Drill be used in cordless drills and quick‑change holders? The MetavCUT Twist Drill with its hexagonal shank is designed for use in both cordless drivers with 1/4" bit holders and standard chucks; the form‑fit hex shank reduces slipping and speeds up tool changes, while the HSS‑G geometry remains suited to both portable and stationary drilling when correct speeds and cooling are applied. What is a Twist Drill used for? The MetavCUT Twist Drill is primarily used for machining high‑strength materials and larger bore requirements in metalwork; its ground geometry is easier to sharpen and withstands higher loads, delivering precise, clean holes even under demanding conditions. Which three drill types exist? There are three common drill types: metal drills (such as the MetavCUT Twist Drill), wood drills and stone/masonry drills. Each type has geometry and materials optimised for its target substrate.
4mm HSS-G Twist Drill DIN 338 ,left cutting - MetavCUT
Kombination aus hoher Standzeit, linksschneidender Ausführung und 135° Spitzenwinkel sorgt für effizientes und kontrolliertes Bohren in Metall; Bestellen Sie den Spiralbohrer direkt über Metav Werkzeuge oder fragen Sie unsere Beratung bei Bedarf an. Spiralbohrer von MetavCUT Profi Line (linksschneidend, HSS‑G) Spiralbohrer von MetavCUT Profi Line für präzise Metallbearbeitung mit linksschneidender Ausführung und 135° Spitzenwinkel. HSS-G Material für hohe Standzeit Linksschneidende Ausführung für Schraubenreste Spitze 135° für härtetaugliches Bohren Geeignet für Handbohrmaschine und Stationärbetrieb Norm DIN 338 kurze Spiralbohrer Langlebigkeit durch hochwertiges Material und smarter Geometrie Der HSS-G Kurzspiralbohrer vereint verschleißfestes Material mit optimierter Schneidengeometrie, sodass die Standzeit deutlich zunimmt. Durch den Einsatz von Schnellarbeitsstahl verbleiben Schnittkante und Schneidenlänge länger intakt, was weniger Werkzeugwechsel und höhere Produktivität bedeutet. Für Anwender heißt das: weniger Stillstandzeit und planbare Arbeitsabläufe bei der Metallbearbeitung. Linksschneidende Ausführung als Lösung für fest sitzende Schrauben Die linksschneidende Schleifung ermöglicht gezielte Eingriffe bei abgebrochenen oder festsitzenden Schrauben, da der Bohrer beim Linkslauf den Schraubenrest oft mit herausdreht. In Kombination mit einer Bohrmaschine mit Linkslauf reduziert diese Technik das Risiko von weiteren Beschädigungen am Werkstück und vereinfacht Reparaturarbeiten. Anwender profitieren von schnellerer Bearbeitung und geringerem Kraftaufwand. Präzision und Einsatzbereiche für professionelle Werkstätten Mit einem Spitzenwinkel von 135° ist das Werkzeug speziell für härtere Werkstoffe ausgelegt und dringt sauberer in Edelstahl, legierten Stahl und Gusseisen ein. Die Ausführung nach DIN 338 bestätigt die Einordnung als kurzer Spiralbohrer mit Zylinderschaft, ideal für stationäre Maschinen und Handmaschinen gleichermaßen. Dadurch eignet sich der Kurzspiralbohrer für Montage, Instandhaltung und präzise Werkstattarbeiten. Praxisnahe Bedienungshinweise für sichere Ergebnisse Für saubere Bohrbilder empfiehlt sich ein Anbohren mit Zentrierbohrer bei hoher Präzision sowie die Nutzung geeigneter Kühlung bei zähen Materialien. Die linksschneidende Geometrie verlangt nicht nach speziellen Drehzahlen, wohl aber nach kontrolliertem Vorschub; so werden Bruchrisiken minimiert. Durch richtige Anwendung lassen sich sowohl Zeitaufwand als auch Werkzeugkosten nachhaltig reduzieren. Empfehlung: Setzen Sie auf die MetavCUT Profi Line mit linksschneidendem HSS‑G Bohrer für kompromisslose Metallbearbeitung; bei technischen Fragen erreichen Sie uns unter info@metav-werkzeuge.com oder telefonisch unter +49 2822 7131930 Produktmerkmale Artikelnummer: 60040-FDA Marke: MetavCUT Serie: Profi Line Bezeichnung: Spiralbohrer Ausführung: linksschneidend Daten Durchmesser: 4 mm Spitzenwinkel: 135° Verpackungseinheit: 10 Besonderheiten Material: HSS-G Norm: DIN 338 (kurze Spiralbohrer mit Zylinderschaft) Für Bohrmaschine: Handbohrmaschine und stationärer Einsatz Linksschneidend: geeignet zum Ausdrehen von Schraubenresten, reduziert Anpresskraft FAQ Für welche Materialien eignet sich der Bohrer am besten? Der MetavCUT Spiralbohrer Profi Line (SKU 60040-FDA) ist ausgelegt für legierte und unlegierte Stähle, Gussstahl, Gusseisen, Temperguss sowie Nichteisenmetalle und Hartkunststoff; der 135° Spitzenwinkel verbessert die Anbohrfähigkeit in harten Werkstoffen. Brauche ich eine spezielle Bohrmaschine für die linksschneidende Ausführung? Für die optimale Nutzung der linksschneidenden Funktion ist eine Bohrmaschine mit Linkslauf erforderlich; ohne Linkslauf bleibt die normale Schneidwirkung des MetavCUT Spiralbohrers aus. Wie reduziert die linksschneidende Geometrie den Kraftaufwand? Durch die linksschneidende Schleifung arbeitet der HSS‑G Bohrer effizienter, wodurch bis zu 50 % weniger Anpresskraft benötigt werden kann und die Bohrgeschwindigkeit im Praxisvergleich um bis zu 40 % steigt. Ist der Bohrer für Handgebrauch geeignet? Ja, der Spiralbohrer aus der Profi Line ist für Handbohrmaschine und stationären Betrieb vorgesehen und eignet sich für Montage und Werkstattarbeiten. Welche Norm gilt für diesen Bohrer und was bedeutet sie? Die Einhaltung von DIN 338 bestätigt, dass es sich um einen kurzen Spiralbohrer mit Zylinderschaft handelt; diese Norm regelt Abmessung, Geometrie und Fertigungsarten für präzise und standardisierte Werkzeuge.
4mm HSS-G Twist Drill DIN 338 ,short, bright finished, Type N - MetavCUT
Twist Drill (Type N) short · 4 mm · 135° Tip · HSS‑G · Bright Finished · DIN 338 · Fully Ground Shank · MetavCUT The Twist Drill Type N short is a precision metal‑drilling bit for Drilling Machines, designed for stable, high‑performance holes in alloyed and unalloyed steels. Short design for high stability 4 mm Diameter for precise holes 135° Tip for hard materials like stainless steel Fully ground shank for accurate clamping Complies with DIN 338 for metalworking Faster, more efficient drilling in hard materials Deriving its cutting performance from HSS‑G Metallurgy, this Twist Drill combines high wear resistance with reliable edge retention. The 135° Tip reduces chipping when penetrating hardened surfaces and shortens lead time on initial contact, so each hole is drilled with less wandering. As a result, workshops benefit from improved cycle times and consistent hole quality. Short design increases rigidity and accuracy A short overall length and a fully ground shank minimise deflection and vibration during machining. According to DIN 338 classifications for short Twist Drills, the reduced overhang delivers higher stability on both stationary and handheld Drilling Machines. This construction is particularly advantageous when precision, roundness and repeatability are priorities. Lower feed forces and broader material range Thanks to the optimized geometry of the HSS‑G flute and the Type N Normal Spiral, this Twist Drill enables up to 40% faster drilling and requires up to 50% less feed force compared with conventional HSS bits. The design makes it well suited for alloyed and unalloyed Steel, Cast Iron, Sintered Iron, Non‑Ferrous Metals and hard Plastics, while still offering straightforward resharpening when required. Ideal users and workshop applications Manufactured for professionals in metalworking, maintenance and precision engineering, the MetavCUT Twist Drill supports demanding shop environments where consistent hole quality matters. Its bright finished surface and short flute length offer easy chip evacuation for drilling depths up to its overall length, while the compact format makes it suitable for confined setups and multi‑tool fixtures. MetavCUT recommends the Twist Drill Type N short HSS‑G for precision metalwork and heavy‑duty shop tasks — for expert technical advice or to confirm suitability contact METAV Werkzeuge: 📧 info@metav-werkzeuge.com ☎️ +49 2822 7131930 ✔️ WhatsApp +49 170 2837271 Designation: Twist Drill Brand: MetavCUT SKU: 27040-FDA Model Series: Basic Line Type: Typ N Diameter: 4 mm Material: HSS-G Norm: DIN 338 Execution: short Shaft Finish: fully ground Spiral Length: 43 mm Overall Length: 75 mm Tip Angle: 135° Colour: bright finished For: Drilling Machine Application: Drill for Metal Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What are Twist Drills used for and which materials suit the MetavCUT Twist Drill Type N short? The MetavCUT Twist Drill Type N short is primarily used for drilling metal; its HSS‑G composition and 135° Tip make it suitable for alloyed and unalloyed Steel, Cast Iron, Sintered Iron, Non‑Ferrous Metals and Hard Plastics, offering reliable hole quality in demanding applications. Which three drill types exist and where does the MetavCUT Twist Drill fit? Three common drill categories are Metal Drills, Wood Drills and Masonry/Concrete Drills. The MetavCUT Twist Drill Type N short is a Metal Drill (Type N Normal Spiral) optimised for metalworking tasks. For what is a Twist Drill generally used? A Twist Drill is chiefly applied to the machining of high‑strength materials and larger diameters; it is easy to resharpen and withstands substantial loads, which is why the MetavCUT Twist Drill is recommended for robust metalworking duties.
4mm HSS-G Twist Drill DIN 338 ,short, bright finished, Type N - MetavCUT
Twist Drill 4 mm — Type N, Short, 135°, Bright finished, HSS-G, DIN 338 (MetavCUT) A Twist Drill (Type N) engineered for precise metal drilling in Drilling Machines and stationary tool setups. Short version for greater rigidity in drilling 4 mm Diameter, 135° Point for hard metals Fully ground HSS-G for sharp, precise holes Complies with DIN 338 for short twist drills Optimised for Drilling Machines and stationary use Greater efficiency and lower feed forces thanks to short design The Twist Drill in a short execution offers a reduced overhang from the chuck, which increases stability and lowers the tendency to bend during machining. The HSS-G material combined with a ground flute geometry enables up to 40% faster drilling and requires roughly 50% less feed force compared with conventional HSS drills. This results in faster cycle times on demanding metal tasks and reduces operator fatigue when working on repetitive holes. Cleaner, more accurate holes through precise grinding and geometry A fully ground flute geometry delivers very sharp cutting edges and high concentricity, producing cleaner holes and improved dimensional accuracy. The 135° point is specifically suited for harder materials such as stainless steel and reduces initial chatter and skidding when starting a hole. For customers unfamiliar with point angles: a larger point angle spreads the cutting action over a broader area, shortening penetration time and improving centre holding on tough metals. Standardised dimensions and classic Type N spiral for metalworking Manufactured to DIN 338, this short Twist Drill follows recognised tolerances and dimensions for short cylindrical-shank metal drills. The Type N normal spiral is ideal for drilling a wide range of metals including alloyed and unalloyed steel, cast materials and non-ferrous metals, as well as engineering plastics. Use in a Drilling Machine or on stationary toolholders ensures best performance; the geometry and finish are optimised for metalworking applications rather than soft-wood tasks. Ideal users and handling advice for long tool life Workshops, toolrooms and precision maintenance shops benefit most from this Standard Line product. Because ground HSS types can be more brittle than rolled alternatives, it is recommended to use the drill in stationary machines with adequate cooling and controlled feed rates to avoid breakage. The bright finished surface and fully ground shank assist with chip evacuation and ensure reliable gripping in chucks or collets, extending service intervals when used following proper machining practice. For expert selection and further technical advice on MetavCUT Twist Drills, contact METAV Werkzeuge via eMail: info@metav-werkzeuge.com or phone: +49 2822 7131930; WhatsApp: +49 170 2837271 Designation: Twist Drill Brand: MetavCUT SKU: 45040-FDA Diameter: 4 mm Overall Length: 75 mm Spiral Length: 43 mm Execution: Short Point Angle: 135° Type: Type N Material: HSS-G Shaft Finish: Fully ground Colour: Bright finished Application: Drills for metal Suitable For: Drilling Machine Standard / Norm: DIN 338 Model Series: Standard Line Manufacturer: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ For what is a Twist Drill mainly used? A MetavCUT Twist Drill (Type N) is primarily applied to machining high-strength materials and larger drill diameters; its geometry is easy to resharpen and withstands greater loads. This form is commonly used when working with metals, as it combines robustness with the ability to produce precise holes in demanding materials. Which three drill types exist? Typical broad categories are metal drills, wood drills, and masonry/concrete drills; the MetavCUT Twist Drill Type N belongs to the metal drill group and is optimised for metalworking rather than soft-wood or stone applications.
4mm HSS-G Twist Drill DIN 338 ,short, bright finished, Type N - MetavCUT
Kompakte Kombination aus Stabilität und Präzision: Der kurze, geschliffene HSS-G Spiralbohrer mit 135° Spitzenwinkel ermöglicht bis zu 40 % schnelleres Bohren bei gleichzeitig 50 % geringerer Anpresskraft und eignet sich besonders für legierte und unlegierte Stähle. Für stationäre Maschinen und handgeführte Bohrmaschinen geeignet. Bestellen Sie den MetavCUT Spiralbohrer direkt über Metav oder fragen Sie unsere Beratung bei Bedarf an. Spiralbohrer 4 mm HSS-G, kurze Ausführung, Profi Line Der Spiralbohrer 4 mm HSS-G in kurzer Ausführung bietet hohe Stabilität und präzise Bohrungen in Metall bei stationären und handgeführten Anwendungen. Kurze Ausführung für höhere Stabilität Geschliffene HSS-G-Geometrie für präzise Bohrungen 135° Spitzenwinkel für harte Werkstoffe Geeignet für Handbohrmaschine und stationäre Maschinen DIN 338 Klassifikation, Profi Line Höhere Standfestigkeit durch kurze Auskraglänge Die kurze Bauform reduziert die Auskraglänge und minimiert somit Verformung und Vibrationen beim Bohren. Dadurch entsteht eine spürbar höhere Stabilität, die insbesondere bei harten Werkstoffen wie legiertem Stahl oder Gusseisen saubere Bohrbilder und längere Werkzeugstandzeiten ermöglicht. Für Anwender heißt das: gleichmäßigere Bohrungsqualität und weniger Ausschuss bei Serien- oder Einzelteilen. Schnelleres und effizienteres Bohren dank geschliffener Geometrie Die geschliffene HSS-G-Geometrie sorgt für sehr scharfe Schneiden und hohe Rundlaufgenauigkeit. In der Praxis führt das zu bis zu 40 % schnellerem Bohren und reduziertem Kraftaufwand, wodurch die Belastung für Maschine und Bediener sinkt. Für weniger erfahrene Anwender ist dies ein Vorteil, weil das Bohren kontrollierter gelingt und das Risiko von Anlaufrissen am Bohranfang reduziert wird. Spezifische Eignung für Metall und Anwendungsbereiche Der Spiralbohrer wurde speziell für die Bearbeitung von Stahl, legiertem Stahl, Gusseisen, Temperguss, Nichteisenmetallen und harten Kunststoffen entwickelt. Als Typ N mit Normalspirale überzeugt er im Standard-Bereich (2–13 mm) und ist für alltägliche Werkstattaufgaben sowie präzise Montagearbeiten gut geeignet. Wer häufig in Metall bohrt, profitiert von der ausgewogenen Kombination aus Standzeit und Zerspanleistung. Praktische Hinweise zur Anwendung und Maschinenwahl Bei handgeführten Bohrmaschinen empfiehlt sich das Anpicken oder Zentrieren vor dem Bohren, um ein Wandern des Bohrers zu vermeiden. Stationäre Maschinen erlauben höhere Präzision und schonen das Werkzeug. Zur Kühlung und Späneabfuhr ist bei langen Serienläufen die Nutzung von Kühlschmierstoff oder geeigneter Späneabfuhr sinnvoll, damit die Lebensdauer des Werkzeugs erhalten bleibt. Vorteile der DIN-338-Norm und geschliffener Ausführung erklärt Die Einordnung nach DIN 338 garantiert standardisierte Abmessungen und Austauschbarkeit. Geschliffen bedeutet, dass die Spirallage präzise per CNC geschliffen wurde, was besonders scharfe Kanten und saubere Bohrungen liefert. Diese Ausführung ist besonders dann vorteilhaft, wenn hohe Maßhaltigkeit und Oberflächenqualität gefordert sind. Empfehlung: Für präzise Metallbearbeitung den MetavCUT Spiralbohrer mit geschliffener HSS-G-Geometrie wählen und Verfügbarkeit direkt bei Metav prüfen: info@metav-werkzeuge.com · Tel. +49 2822 7131930 · WhatsApp +49 170 2837271 Produktmerkmale Artikelnummer: 48040-FDA Marke: MetavCUT Serie: Profi Line Bezeichnung: Spiralbohrer Fakten Durchmesser: 4 mm Gesamtlänge: 75 mm Spirallänge: 43 mm Spitzenwinkel: 135° Verpackungseinheit: 10 Besonderheiten Material: HSS-G (Schnellarbeitsstahl, geschliffen) Schaftausführung: geschliffen (voll geschliffen für hohe Rundlaufgenauigkeit) Norm: DIN 338 (kurze Spiralbohrer mit Zylinderschaft) Ausführung: kurz (reduzierte Auskraglänge, höhere Stabilität) Typ: Typ N (Normalspirale, geeignet für Metallbearbeitung) Oberfläche: blank (bright finished) Für Bohrmaschine: Handbohrmaschine FAQ Ist der Spiralbohrer für Edelstahl geeignet? Der MetavCUT Spiralbohrer 4 mm HSS-G mit 135° Spitzenwinkel eignet sich für viele harte Werkstoffe; bei besonders zähem Edelstahl sind angepasste Schnittwerte und Kühlung empfehlenswert, um Standzeit zu maximieren. Kann der Bohrer in einer Handbohrmaschine verwendet werden? Ja, der kurze Spiralbohrer wurde für den Einsatz in Handbohrmaschinen und stationären Maschinen konzipiert; durch die kurze Ausführung erhöht sich die Stabilität beim handgeführten Bohren. Was bedeutet HSS-G geschliffen und welchen Vorteil bringt das? HSS-G steht für geschliffenen Schnellarbeitsstahl; diese Fertigungsart liefert sehr scharfe Schneiden und hohe Rundlaufgenauigkeit, was zu präziseren Bohrlöchern und häufig besseren Oberflächen führt. Wie beeinflusst der 135° Spitzenwinkel die Bohrung? Der größere Spitzenwinkel reduziert die Anbohrbelastung in harten Werkstoffen, verbessert die Zentrierung und verringert das Risiko von Ausrissen; daher ist er für legierte Stähle und Gussmaterialien empfehlenswert. Ist der Bohrer nach DIN 338 gefertigt und was heißt das praktisch? Ja, die Ausführung entspricht DIN 338; das garantiert standardisierte Abmessungen, Austauschbarkeit und eine klare Einordnung der kurzen Spiralbohrer mit Zylinderschaft.
4mm HSS-G Twist Drill DIN 338 ,short, TIN-coated - MetavCUT
Die Kombination aus HSS-G geschliffener Geometrie, TiN-Beschichtung und der kurzen Ausführung sorgt für hohe Stabilität und lange Standzeit bei der Metallbearbeitung. Nutzen Sie diese Vorteile für präzise Bohrbilder in Stahl und Nichteisenmetallen. Bestellen Sie den Spiralbohrer direkt über Metav Werkzeuge oder fragen Sie unsere Beratung bei Bedarf an. Spiralbohrer von MetavCUT, kurze HSS-G Ausführung Spiralbohrer von MetavCUT, kurze Ausführung für präzises Bohren in Stahl und NE-Metallen Ausführung kurz für höhere Stabilität Material HSS-G geschliffen für präzise Bohrbilder Beschichtung TiN reduziert Reibung und Verschleiß Geeignet für legierte und unlegierte Stähle Norm DIN 338 konform, Zylinderschaft geeignet Hohe Stabilität für präzise Metallbohrungen Dank der kurzen Auskraglänge bietet dieser Kurzbohrer eine deutlich verringerte Neigung zum Verbiegen und ermöglicht so konstante Präzision bei Bohrungen in harten Werkstoffen. Die geschliffene Schaftausführung sorgt für hohe Rundlaufgenauigkeit, wodurch saubere Bohrlöcher mit reproduzierbaren Toleranzen entstehen. Diese Eigenschaft ist besonders vorteilhaft bei stationären oder handgeführten Maschinen, die exakte Ergebnisse verlangen. Effizienzsteigerung durch geschliffene Geometrie Die geschliffene Spiralgeometrie ermöglicht ein schnelleres Eindringen in das Werkstück bei gleichzeitig geringerem Kraftaufwand. Herstellerangaben zufolge kann die Produktivzeit um bis zu 40 % reduziert werden, während die benötigte Anpresskraft deutlich sinkt. Dies führt zu ergonomischen Vorteilen für den Anwender und zu höherer Prozesssicherheit bei Serien- und Einzelteilen. TiN-Beschichtung für längere Standzeit Die TiN-beschichtete Oberfläche verringert Wärmeentwicklung und Reibung beim Bohren, wodurch sich der Werkzeugverschleiß reduziert. In Kombination mit einer geeigneten Kühlung werden Temperaturspitzen vermieden und die Lebensdauer des Werkzeugs verlängert. Diese Beschichtung eignet sich besonders für das Bearbeiten von Stahl, Gusseisen und Nicht-Eisen-Metallen. Einsatzbereiche und Zielgruppe Der Bohrer ist für die Metallbearbeitung in Werkstatt, Montage und leichten industriellen Anwendungen ausgelegt und passt zur Handbohrmaschine sowie zu stationären Bohrvorrichtungen. Typische Einsatzstoffe sind legierte und unlegierte Stähle, Temperguss, Gusseisen, Sintereisen, Kupfer, Bronze und Hartkunststoff. Anwender profitieren vor allem, wenn Stabilität, Standzeit und saubere Bohrbilder im Vordergrund stehen. Empfehlung: Der MetavCUT Kurzbohrer in HSS-G mit TiN-Beschichtung bietet besonders bei anspruchsvollen Metallbohrungen höchste Präzision und Standzeit – bestellen Sie direkt bei Metav Werkzeuge oder kontaktieren Sie info@metav-werkzeuge.com / ☎️ +49 2822 7131930 Produktmerkmale Artikelnummer: 28040-FDA Marke: MetavCUT Bezeichnung: Spiralbohrer Serie: Basic Line Norm: DIN 338 Daten Gesamtlänge: 75 mm Spirallänge: 43 mm Durchmesser: 4 mm Spitzenwinkel: 118° Verpackungseinheit: 10 Stück Besonderheiten Material: HSS-G (Schnellarbeitsstahl, geschliffen) Beschichtung: TiN (Titan-Nitrid-Beschichtung) Schaftausführung: geschliffen Ausführung: kurz Einsatz: Handbohrmaschine und stationäre Maschinen Geeignet für: legierte und unlegierte Stähle; Gusseisen; Sintereisen; Kupfer; Bronze; Hartkunststoff Normhinweis: DIN 338 (kurze Spiralbohrer mit Zylinderschaft) FAQ Ist der Bohrer für Handbohrmaschinen geeignet? Der MetavCUT Spiralbohrer (Spiralbohrer, SKU 28040-FDA) ist für den Einsatz in Handbohrmaschinen geeignet, besonders wegen der kurzen Ausführung, die die Stabilität erhöht und das Wandern des Bohrers reduziert. Welche Materialien lassen sich mit dem Bohrer bearbeiten? Mit dem MetavCUT HSS-G Kurzbohrer lassen sich legierte und unlegierte Stähle, Temperguss, Gusseisen, Sintereisen sowie Kupfer, Bronze und Hartkunststoff zuverlässig bearbeiten. Wie verbessert die TiN-Beschichtung die Leistung? Die TiN-Beschichtung des MetavCUT Spiralbohrers reduziert Reibung und Wärme, verringert dadurch den Verschleiß und verlängert die Standzeit bei Metallbohrungen, insbesondere bei Verwendung von Kühlmittel. Was bedeutet geschliffen im Zusammenhang mit diesem Bohrer? Geschliffen bedeutet, dass die Geometrie des HSS-G Bohrers durch Schleifen hergestellt wurde, was zu besonders scharfen Schneiden und hoher Rundlaufgenauigkeit führt; beim MetavCUT Spiralbohrer sorgt dies für präzise Bohrlöcher. Entspricht der Bohrer einer Norm und was heißt das für die Anwendung? Ja, der MetavCUT Spiralbohrer entspricht der DIN 338, was bedeutet, dass es sich um einen kurzen Spiralbohrer mit Zylinderschaft handelt und damit kompatibel mit gängigen Spannfuttern und Einsatzfällen in Werkstatt und Produktion ist.
4mm HSS-G Twist Drill DIN 338 ,short, TIN-coated, Type N - MetavCUT
Twist Drill 4 mm — Type N, Short, TIN-coated HSS-G, 135° (DIN 338) by MetavCUT The Twist Drill 4 mm is a short Type N drill designed for precise metal drilling with a Drilling Machine, combining a TIN-coated finish and HSS-G material for enhanced life and performance. Short design for improved stability and precision TIN-coated surface for reduced friction and wear Fully ground shank for high concentricity and clean holes 135° point angle for tougher materials and stainless steel Conforms to DIN 338 for short HSS twist drills Increased precision and longer tool life for metalworking Engineered for demanding metal applications, this short Twist Drill from MetavCUT delivers reliable performance when working with alloyed and unalloyed steel, cast iron and non-ferrous metals. The HSS-G construction means the flute geometry is produced by grinding, resulting in very sharp cutting edges and superior concentricity. The TIN-coated surface reduces friction and wear during cutting, which extends service life especially under appropriate cooling. For users seeking cleaner holes with fewer burrs, the ground geometry offers a measurable benefit in repeatable accuracy. Stability and faster feeds thanks to the short design Because the overall length is reduced, the short execution offers higher rigidity and less tendency to bend under load, which allows for more aggressive feed rates and a reduction in wandering when starting a hole. The fully ground shank ensures excellent runout characteristics in standard chucks, improving hole quality. The 135° point angle is optimised for harder materials and stainless steels: it shortens initial penetration and reduces the risk of chipping at the tip. For workshop environments where precision and cycle-time matter, this configuration supports efficient and consistent production. Practical use, compatibility and recommended handling This Type N Twist Drill is intended primarily for metalworking on stationary or portable drilling machines and is particularly suitable when holes up to moderate depths are required. For best results, use suitable coolant to benefit from the TIN coating and to reduce heat-related wear. The short, ground design makes the bit easier to regrind compared with rolled geometries, but care should be taken to avoid excessive force; the combination of sharpness and some brittleness makes controlled feeds advisable. Users seeking guidance on selecting the correct bit for specific alloys or machine setups can rely on METAV Werkzeuge’s expert consultation. Choose MetavCUT’s short TIN-coated Twist Drill for demanding metal drilling — for expert selection and technical advice contact METAV Werkzeuge: eMail info@metav-werkzeuge.com — Phone +49 2822 7131930 — WhatsApp +49 170 2837271 Technical information Designation: Twist Drill 4 mm Brand: MetavCUT SKU: 46040-FDA Diameter: 4 mm Point angle: 135° Type: Type N Execution: Short Coating/Colour: TIN-coated Material: HSS-G Shank finish: Fully ground Spiral length: 43 mm Overall length: 75 mm Application: Drills for metal Conforms to: DIN 338 Model series: Standard Line For drilling machine: Drilling Machine Manufacturer: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What is the Twist Drill 4 mm used for and which materials suit it best? The MetavCUT Twist Drill 4 mm (Type N) is primarily used for metalworking; it is applied to alloyed and unalloyed steel, temper castings, cast iron, sintered iron, brass, copper, bronze and hard plastics. Short, ground geometry and TIN coating make it robust for high-strength materials and larger diameters where durability is essential. Which three drill types exist and how does the MetavCUT Twist Drill fit in? Besides the MetavCUT Twist Drill (Type N) tailored for metal, the three main drill categories are: metal drills, wood drills and stone/concrete drills. The MetavCUT product belongs to the metal drill category, optimised for metalworking tasks rather than timber or masonry applications.
4mm HSS-G Twist Drill DIN 338 ,short, TIN-coated, Type N - MetavCUT
Kombinieren Sie die höhere Stabilität der kurzen Ausführung mit der Abriebfestigkeit der TIN-beschichteten Oberfläche und dem präzisen geschliffenen HSS-G für saubere Metallbohrungen; bestellen Sie das Werkzeug direkt über Metav oder lassen Sie sich bei technischen Fragen von unserer Beratung unterstützen. Spiralbohrer von MetavCUT (HSS-G, kurz) Der Spiralbohrer in kurzer Ausführung ist ein spezialisierter Metallbohrer für präzise Bohrungen in legierten und unlegierten Stählen, Gusseisen und Nichteisenmetallen. Kurze Ausführung für hohe Stabilität TIN-beschichtet reduziert Reibung und Verschleiß Geschliffenes HSS-G für saubere Bohrbilder Spitzenwinkel 135° für härtere Werkstoffe Passend für Handbohrmaschine mit Zylinderschaft Robuste Materialwahl für langlebige Metallbohrungen Dank der Kombination aus HSS-G und TIN-beschichtet ist dieses Werkzeug auf hohe Beanspruchung bei Metall-Bearbeitung ausgelegt. HSS-G steht für geschliffenen Schnellarbeitsstahl, der sehr scharfe Schneiden und exakten Rundlauf liefert; das Ergebnis sind saubere Bohrlöcher mit geringer Gratbildung. Die Titan-Nitrid-Beschichtung verringert Reibung und Oberflächenhitze, was die Standzeit erhöht und den Werkzeugwechsel reduziert. Präzision und Stabilität bei handgeführten Arbeiten Für den Einsatz im Standard-Bereich (2–13 mm) ist die kurze Auskraglänge ein klarer Vorteil: Weniger Ausschlag und geringere Neigung zum Verbiegen sorgen für höhere Bohrgenauigkeit bei Handbohrmaschinen und stationären Säulenbohrern. Bei besonders hohen Genauigkeitsanforderungen empfiehlt sich ein Anpünktchen oder Zentrierbohrer vor dem Direktschnitt, um das „Wandern“ des Bohrers zu minimieren. Effiziente Leistung durch geschliffene Geometrie Durch den CNC-Schliff reduziert sich die Anpresskraft erheblich; Anwender profitieren von einem bis zu 40 % schnelleren Bohren und deutlich geringerem Kraftaufwand im Vergleich zu herkömmlichen HSS-Werkzeugen. Die geschliffene Spirale ermöglicht zudem bessere Späneführung bei moderaten Schnittparametern, wodurch das Risiko von Bruch oder Einlaufen bei dieser kurzen Ausführung sinkt. Einsatzspektrum und Anwendungsempfehlung Dieses Präzisionswerkzeug eignet sich für Werkstätten, Montage und anspruchsvolle Handwerksarbeiten, insbesondere dort, wo Stahl, Temperguss, Gusseisen oder Nichteisenmetalle bearbeitet werden. Als Typ N (Normalspirale) bietet es universelle Eignung für Metall; bei Dauerbetrieb oder harten Werkstoffen wird eine Kühlung empfohlen, um die Lebensdauer weiter zu erhöhen. Setzen Sie auf die Profi Line von MetavCUT und fordern Sie ein individuelles Angebot über Metav an – E‑Mail: info@metav-werkzeuge.com Produktmerkmale Bezeichnung: Spiralbohrer Artikelnummer: 41040-FDA Hersteller: MetavCUT Serie: Profi Line Norm: DIN 338 (kurze Spiralbohrer) Fakten Durchmesser: 4 mm Gesamtlänge: 75 mm Spirallänge: 43 mm Spitzenwinkel: 135° Verpackungseinheit: 10 Besonderheiten Material: HSS-G (geschliffen) Schaftausführung: geschliffen Beschichtung: TIN-beschichtet (Titan-Nitrid) Typ: Typ N (Normalspirale) Für: Handbohrmaschine FAQ Für welche Materialien ist dieses Werkzeug geeignet? Der Spiralbohrer von MetavCUT Profi Line eignet sich für legierten und unlegierten Stahl, Gusseisen, Temperguss sowie Nichteisenmetalle; die TIN-beschichtete Oberfläche trägt zur erhöhten Standzeit bei. Kann der Bohrer in einer Handbohrmaschine eingesetzt werden? Ja, der kurze Aufbau und die Zylinderschaft machen den Spiralbohrer von MetavCUT ideal für Handbohrmaschine; bei feinen Passungen empfiehlt sich vorheriges Anpünktchen. Was bewirkt der Spitzenwinkel von 135°? Der Spitzenwinkel von 135° erhöht die Standzeit und erleichtert das Anbohren harter Werkstoffe; der Spiralbohrer 41040-FDA dringt damit kontrollierter in Edelstahlähnliche Materialien ein. Warum ist geschliffenes HSS (HSS-G) vorteilhaft? Geschliffenes HSS bietet sehr scharfe Kanten und hohe Rundlaufgenauigkeit, wodurch der Spiralbohrer schneller schneidet und sauberere Bohrbilder erzeugt; die Baureihe Profi Line ist darauf ausgelegt, Präzision zu liefern. Welche Vorteile bringt die TIN-Beschichtung konkret? Die Titan-Nitrid-Beschichtung reduziert Reibung und thermische Belastung; dadurch arbeitet der Spiralbohrer von MetavCUT länger zuverlässig und weist geringeren Verschleiß auf.
4mm HSS-G Twist Drill DIN 338 - MetavCUT
Twist Drill — 4 mm HSS‑G, 135° Tip, DIN 338, Spezial Series The Twist Drill is a precision metal‑drilling bit for Drilling Machines, engineered for fast, burr‑free holes in alloyed and unalloyed steels as well as non‑ferrous metals. Up to 40% faster drilling performance Reduced feed force by 50% for easier machining 135° tip for hard materials and stainless steel HSS‑G material for increased wear resistance Multi‑bevel cutting edge, cylindrical shank design Faster, more efficient metal drilling for workshops and industry The specially ground HSS‑G geometry of this Twist Drill delivers significantly improved cutting action: users benefit from up to 40% faster drilling and 50% less feed force compared with conventional HSS bits. This translates into shorter cycle times and reduced operator fatigue when working on tougher materials. The result is consistent, burr‑reduced holes and fewer rework steps, which increases productivity in production workshops and maintenance shops alike. Reliable centring and clean entry for hard materials A 135° tip angle gives the Twist Drill better centring and a gentler entry into harder materials such as stainless steel, reducing the tendency to wander and lowering burr formation at the hole edge. With a Spiral Length of 43 mm and an Overall Length of 75 mm, the geometry supports stable chip evacuation and controlled drilling depth on typical metalworking tasks. Proper tip geometry means cleaner holes with less need for subsequent deburring. Conforms to DIN 338 for short cylinder‑shank twist drills Designed and classified according to DIN 338, this short Twist Drill with cylindrical shank is suitable for stationary and portable Drilling Machines. The multi‑bevel cutting edge (with W‑point, without triangular shank) improves cutting performance and lifetime, especially when machining Cast Steel, Gusseisen, Sintered Iron, Tempered Casts, Aluminium and many engineering plastics. The standardized design ensures interchangeability and reliable performance in production environments. Ideal users, applications and practical handling tips This Twist Drill is aimed at professional machinists, toolrooms and industrial maintenance teams who require repeatable quality in metal drilling. For best results use appropriate cutting speeds and coolant for the material, clamp the workpiece securely, and match the drill speed to the material hardness. If unsure about speeds, coolant type or suitability for a specific application, METAV Werkzeuge offers competent technical advice and support to help select the right tool and parameters. We recommend the MetavCUT Twist Drill for demanding metalworking applications — for personalised technical advice and ordering assistance contact METAV Werkzeuge: info@metav-werkzeuge.com · Phone +49 2822 7131930 · WhatsApp +49 170 2837271 Technical data Designation: Twist Drill Brand: MetavCUT SKU: 55040-FDA Diameter: 4 mm Tip angle: 135° Spiral length: 43 mm Overall length: 75 mm Material: HSS‑G Shank: with multi‑bevel cutting edge, without triangular shank Model series: Spezial Standard: DIN 338 Application: Drills for metal For drilling machine: Drilling Machine Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What is the Twist Drill used for and which materials are suitable? The MetavCUT Twist Drill is primarily used for machining high‑strength materials and larger hole diameters; it performs well in alloyed and unalloyed steel, cast materials, non‑ferrous metals and certain plastics. Its ground geometry is easy to resharpen and designed to withstand higher loads during drilling. Which three drill types are commonly distinguished? Common drill categories are metal drills, wood drills and stone/concrete drills; the MetavCUT Twist Drill belongs to the metal drill category and is optimised for metalworking applications. Why are Twist Drills point‑sharpened? Point sharpening reduces the cross‑cut at the tip, which lowers friction and requires less feed force; as a result the MetavCUT Twist Drill centres more reliably and produces cleaner hole entries with reduced burr formation. Can a metal drill be used to drill wood? A metal drill such as the MetavCUT Twist Drill can be used in wood, but guidance and surface finish are typically inferior to a dedicated wood drill. Metal drills are easier to resharpen and have less self‑pulling action compared with specialised wood bits. Are you not sure whether this Twist Drill meets your exact requirements or do you need additional technical specifications? METAV Werkzeuge provides comprehensive and expert consultation — feel free to contact us by email at info@metav-werkzeuge.com, by phone at +49 2822 7131930 or via WhatsApp at +49 170 2837271.
4mm HSS-G Twist Drill DIN 340 ,long, bright finished - MetavCUT
Twist Drill — 4 mm, 135° tip, long HSS-G, bright finished, fully ground shank, DIN 340, MetavCUT A MetavCUT Twist Drill in long execution for deep metal drilling, designed for Drilling Machines and hardened materials. HSS-G ground for precise metal drilling Long design for deep or hard-to-reach holes 135° tip for harder materials and reduced wander Fully ground shank for high concentricity Conforms to DIN 340 for reliable performance Faster, cleaner metal drilling thanks to ground HSS-G design The long Twist Drill is manufactured from HSS-G (ground high-speed steel), a choice that delivers sharper cutting edges and excellent roundness. Ground geometry reduces cutting forces, enabling up to 40% faster drilling and requiring about 50% less feed pressure compared with conventional HSS bits. This makes the tool particularly valuable when working with alloyed and unalloyed steel, cast materials or other demanding metals where precision and efficiency matter. Long execution optimised for deep holes and limited access With an overall length of 119 mm and a spiral (working) length of 78 mm, the long execution follows the DIN 340 principle to reach deeper bore positions and recessed drilling points. The extended reach is ideal when access is restricted or when drilling through components of greater thickness. The geometry supports stable chip evacuation over longer depths, reducing the need for frequent retraction and improving workflow in series or workshop applications. Tip geometry tailored to hard materials and accurate centring The 135° tip reduces the tendency to walk on hard surfaces and shortens the initial penetration time, which is beneficial for stainless steels and other tough workpieces. The design is suitable for alloyed and unalloyed steel, cast steel, grey and spheroidal graphite cast iron, sintered iron, malleable castings, non‑ferrous metals and hard plastics. For users less familiar with drill geometry: a larger point angle produces a flatter tip that spreads cutting action over a wider area, improving tool life and hole quality in dense materials. Ground flutes and shank—advantages and handling recommendations A fully ground flute and fully ground shank deliver high concentricity and precise bore results, but ground tools can be less forgiving than rolled equivalents. To avoid breakage, operate the drill with appropriate coolant and moderate feed for the material being processed, and prefer stationary machines or guided supports for deep holes. If regrinding is necessary, ground bits allow precise restoration but require careful, professional sharpening to maintain geometry and performance. For demanding metalworking choose the MetavCUT long Twist Drill with HSS‑G for reliable deep-hole performance — METAV Werkzeuge offers expert advice and technical support: info@metav-werkzeuge.com | +49 2822 7131930 | WhatsApp +49 170 2837271 Designation: Twist Drill Brand: MetavCUT SKU: 53040-FDA Diameter: 4 mm Overall length: 119 mm Spiral length: 78 mm Point angle: 135° Execution: long Shank finish: fully ground Surface finish / Colour: bright finished Material: HSS-G Standard: DIN 340 Intended for: Drilling Machine Model series: Standard Line Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ Is the MetavCUT Twist Drill long HSS-G suitable for stainless steel? The MetavCUT Twist Drill in long execution with HSS-G material and a 135° tip is well suited for stainless steel and other harder metals, as the geometry reduces tendency to wander and provides improved cutting action on dense workpieces. Can the MetavCUT Twist Drill be used in portable hand drills? Although the MetavCUT long Twist Drill is designed for Drilling Machines, it can be used in robust portable hand drills if the machine provides stable RPM control and the application permits adequate cooling; however, for deep or high-precision holes a stationary setup is recommended. What is a Twist Drill mainly used for? A Twist Drill is mainly applied to machining high-strength materials and larger bore diameters; it is easy to resharpen and withstands higher loads, making it suitable for alloyed and unalloyed steels, cast irons, sintered metals and hard plastics. Which three drill types exist? There are three primary drill types: Metal drills, Wood drills and Stone/Concrete drills.
4mm NC Centre Drill HSS-Co 90° 12mm Flute, DIN 1835-A - TECWERK
Combining HSS‑Co robustness, a 90° point for accurate centring and a DIN 1835‑A cylindrical shank ensures reliable, repeatable pre‑drilling and chamfering on CNC equipment; order the NC centre drill directly via Metav Werkzeuge or consult our technical team for tailored advice. TECWERK NC centre drill D 4 mm, HSS‑Co, 90° point TECWERK NC centre drill D 4 mm HSS‑Co — a precision spot drill for repeatable centring and rapid pre‑drilling on NC machines and boring mills HSS‑Co for high wear resistance 90° point for precise centring Cylindrical shank to DIN 1835‑A Feed 0.03 mm/rev in steel up to 800 N High‑performance material and design for consistent results Manufactured from HSS‑Co, this spot drill offers elevated hot hardness and wear resistance that supports sustained production runs. The 90° point produces a clean, well‑defined centre that reduces radial run‑out when followed by subsequent drilling or reaming operations. Combined with a cylindrical shank compliant with DIN 1835‑A, the tool integrates seamlessly with automatic tool changers and collet systems, delivering the consistency required for series production and precision tasks. Precision fit and reduced setup time for efficient workflows The tool's h8 diameter tolerance and compact geometry reduce variances during tool changes, which helps to cut setup time on CNC machines and drill rigs. Its geometry is engineered for both centring and chamfering in a single pass, enabling the elimination of separate chamfering steps and thus shortening cycle times. The result is improved machine uptime and a more predictable production flow in metalworking environments. Machining parameters that balance speed and surface quality With a flute (spiral) length of 12 mm and an overall length of 55 mm, the drill is optimised for short overhangs and stable cutting conditions. The recommended feed of 0.03 mm/rev in steel up to 800 N provides a practical starting point for achieving repeatable hole starts without compromising edge quality. The right‑hand cutting geometry suits standard clockwise spindle rotation and supports conventional toolpath strategies on CNC platforms. Robust application range and straightforward handling Designed for fast, position‑accurate pre‑drilling on NC machines and boring mills, the centre drill is also suitable for preparing thread starts where clean chamfers and correct centring are essential. The combination of HSS‑Co material and the specified point geometry prolongs tool life under frequent use, while the standard DIN 1835‑A shank simplifies tool change procedures—making this spot drill a practical choice for workshops aiming to improve first‑pass accuracy and reduce rework. For dependable centring and faster setup, contact Metav Werkzeuge in Emmerich to request a quote or technical consultation for this TECWERK NC centre drill (SKU 2000860104NW) — email info@metav-werkzeuge.com or call +49 2822 7131930 to discuss compatibility with existing tooling systems Technical data Article number: 2000860104NW Standard: DIN 1835‑A Material: HSS‑Co Product type: NC centre drill Facts Diameter: 4 mm Overall length: 55 mm Spiral (flute) length: 12 mm Point angle: 90° Tolerance diameter: h8 Feed in steel up to 800 N: 0.03 mm/rev Packaging unit: 1 Special features Cylindrical shank to DIN 1835‑A Right‑hand cutting For position‑accurate and fast pre‑drilling on NC machines and boring mills For centring and chamfering of thread holes in one pass HSS‑Co construction FAQ What materials is this centre drill suitable for? The TECWERK NC centre drill (NC‑Anbohrer) with HSS‑Co construction is intended primarily for steel applications as specified; the tool is optimised for centring and pre‑drilling on NC machines and boring mills. How does the DIN 1835‑A shank benefit machine use? A DIN 1835‑A cylindrical shank ensures compatibility with standard tool holders and automatic tool changers, improving repeatability and ease of integration of the TECWERK NC centre drill (SKU 2000860104NW) into existing CNC tool systems. What feed rate should be used for reliable centring? A recommended feed of 0.03 mm/rev in steel up to 800 N is cited for reliable hole starts; adjust feeds according to machine rigidity and workpiece clamping to maintain edge quality. Can the tool also chamfer thread holes? Yes, the geometry allows for centring and chamfering of threaded holes in a single operation, reducing the number of tool changes and cycle time when using the TECWERK NC centre drill. Is the tolerance tight enough for precision work? The h8 diameter tolerance provides a precision fit suitable for typical centring operations and helps to ensure consistent location when changing tools. Manufacturer/Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund
4mm NC Spot Drill HSS-Co 120° Right-Hand Shank Cylindrical DIN 1835-A - TECWERK
Take advantage of precise centring, durable HSS‑Co construction and a 120° tip for fast, repeatable spot‑drilling and chamfering in one pass. Order the NC centre drill directly via Metav Werkzeuge or ask our consultants if needed. NC centre drill D.4 mm HSS‑Co 120° – TECWERK The NC centre drill D.4 mm HSS‑Co 120° TECWERK is a machine‑grade spot drill designed for positional centring and chamfering on NC machines and drilling rigs. HSS‑Co for heat and wear resistance Cylindrical shank to DIN 1835‑A 120° tip for precise centring Right‑hand cutting for standard setups Increase machining uptime with precise two‑step operations The cobalt‑alloyed HSS‑Co construction offers improved heat resistance and edge stability compared with plain high‑speed steel, which means longer tool life under intermittent spot‑drilling. The 120° tip combines centring and initial chamfering so that positional holes and tapped hole countersinks are created in a single pass, reducing setup changes and cycle time. For manufacturers focused on efficient production, this translates into fewer tool changes and consistent hole geometry on repeated runs. Reliable clamping and repeatable alignment for NC plants Equipped with a cylindrical shank to DIN 1835‑A and a tolerance h8, the tool provides secure, concentric clamping in standard toolholders. The right‑hand cutting geometry is optimised for conventional spindle rotation on numerically controlled machines, ensuring predictable chip flow and minimal axial runout. These design choices support repeatable centre location and reduce the need for secondary alignment operations on milling centres and drilling rigs. Material guidance and practical application notes Cobalt‑alloyed high‑speed steel is particularly suited to demanding spot‑drilling where higher temperatures and intermittent contact occur. The tool is intended for positional spot‑drilling and simultaneous chamfering of tapped holes, making it suitable for preparatory work before thread tapping. The specification includes a recommended feed of 0.03 mm/rev in steel up to 800 N, which balances cutting pressure and tool life; practitioners with less metrology experience can view this as a starting point for process tuning rather than a fixed setting. Consistent production quality with a compact tool solution By combining centring and chamfering into one operation, the drill helps to lower non‑productive time and reduce potential misalignment between separate tools. The compact geometry — 4 mm diameter with a 12 mm spiral length and 55 mm overall length — is optimised for machine access in crowded fixturing. The net effect is a small, robust component that supports steady production rates and simplifies tooling inventories when supplied as part of a broader workshop equipment strategy. For procurement or technical clarification, contact Metav Werkzeuge — experienced precision partners delivering a broad range of metrology and workshop supplies from Emmerich; email info@metav-werkzeuge.com or call +49 2822 7131930 to discuss suitability and availability Technical data Article number: 2000860084NW Type: NC centre drill Brand: TECWERK Standard: DIN 1835‑A Data Diameter: 4 mm Overall length: 55 mm Spiral length: 12 mm Tip angle: 120° Shank tolerance: h8 Packaging unit: 1 Special features Material: HSS‑Co Shank: cylindrical (DIN 1835‑A) Cutting direction: right‑hand cutting Application: positional spot‑drilling on NC machines and drilling rigs Function: centring and chamfering of tapped holes in one pass Recommended feed in steel up to 800 N: 0.03 mm/rev FAQ What are the primary uses for this centre drill? The TECWERK NC centre drill (SKU 2000860084NW) is intended for positional spot‑drilling and chamfering of tapped holes on NC machines and drilling rigs, combining centring and initial chamfering in one operation. Which materials is the tool suitable for? The HSS‑Co alloy used in this NC centre drill offers enhanced heat and wear resistance, making it well suited to steel and general workshop materials where intermittent contact and elevated cutting temperatures occur. How does the DIN 1835‑A shank benefit machine setup? The cylindrical shank to DIN 1835‑A ensures compatibility with standard collets and toolholders, providing secure clamping and concentric runout for repeatable hole positions across production batches. What feed should be used when spot‑drilling steel? A recommended starting feed is 0.03 mm/rev in steel up to 800 N; this guideline for the TECWERK centre drill balances cutting forces and tool life and can be adjusted during process optimisation. Can the tool perform chamfering and centring in one pass? Yes, the 120° tip geometry of the TECWERK NC centre drill is designed to centre and create the initial chamfer for tapped holes in a single operation, reducing setup time and tool changes. Manufacturer/Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund
4mm NC Spot Drill HSS-Co TiN 90° DIN 1835-A, 12mm Spiral, h8 Tolerance - TECWERK
Combine precise centring, a durable TiN coating and a DIN 1835‑A cylindrical shank for reliable, repeatable spot‑drilling on NC machines; benefit from fast, one‑pass centring and chamfering. Order directly via Metav Werkzeuge or consult the Metav advisors for process support. NC spot drill D.4 mm HSS‑Co TiN 90° by TECWERK The NC spot drill D.4 mm is a high‑precision spot‑drilling tool for position‑accurate centring and simultaneous chamfering on NC machines and drilling rigs. 90° tip for accurate centring TiN coating for extended tool life DIN 1835‑A cylindrical shank for secure clamping Feed 0.03 mm/rev at 800 N for steel Fast, accurate centring and chamfering in one pass Designed for position‑accurate spot‑drilling, this tool enables centring and chamfering of threaded holes in a single operation, reducing setups and cycle times. The 90° tip gives a defined seating angle that simplifies subsequent tapping operations and improves thread alignment. Where process stability is paramount, combining a defined tip geometry with the specified feed of 0.03 mm/rev (steel at up to 800 N) delivers consistent hole starts and reduces the risk of misfeeds or tap breakage, supporting higher first‑pass yields and predictable production throughput. Built for thermal stress and long life Manufactured from HSS‑Co (cobalt high‑speed steel) and finished with a TiN layer, the cutter resists heat build‑up and abrasive wear during interrupted cuts typical of spot drilling. The TiN film reduces friction and extends tool life, while the cobalt alloy substrate maintains hardness at elevated temperatures common in NC machining. The tool’s 12 mm spiral and overall length of 55 mm balance chip evacuation with rigidity, allowing stable operation on both automated NC spindles and conventional drilling rigs without sacrificing service life. Precision fit and reliable clamping for production use Equipped with a cylindrical shank to DIN 1835‑A and produced to h8 diameter tolerance, the tool offers secure seating in standard collets and toolholders, which minimises run‑out and preserves hole accuracy over long runs. The right‑hand cutting geometry suits standard spindle rotations and supports predictable chip flow. These design choices translate into repeatable hole position and angle control, key for downstream operations such as tapping and reaming in batch production. Practical benefits for workshop and production environments For workshop managers and production engineers, the tool reduces handling and setup time by delivering centring and chamfering in one operation and by offering a shank standard that fits common toolholding systems. The combination of HSS‑Co and TiN reduces replacement frequency, while the DIN shank standardisation eases inventory management. The result is a focused improvement in process reliability and a reduction in non‑productive time for routine hole preparation tasks. For robust, repeatable spot‑drilling with TECWERK quality, contact Metav Werkzeuge — Metav is ready to advise on integration into existing NC processes and to support orders from Emmerich: info@metav-werkzeuge.com, +49 2822 7131930 Technical data Article number: 2000861384NW Label: NC spot drill D.4mm HSS‑Co TiN 90° TECWERK Norm: DIN 1835‑A Facts Diameter: 4 mm Overall length: 55 mm Spiral length: 12 mm Tip angle: 90° Tolerance diameter: h8 Packaging unit: 1 Feed in steel (up to 800 N): 0.03 mm/rev Special features Material: HSS‑Co (cobalt high‑speed steel) Coating: TiN Shank execution: cylindrical shank Cutting direction: right‑hand cutting Application: position‑accurate and quick spot‑drilling on NC machines and drilling rigs; centring and chamfering of threaded holes in one pass FAQ What materials is the NC spot drill suitable for? The TECWERK NC spot drill D.4 mm (SKU 2000861384NW) is specified for steel applications, with a documented feed of 0.03 mm/rev in steel at up to 800 N; suitability for other materials should be validated in test cuts. Does the shank fit common toolholders? Yes, the tool uses a cylindrical shank to DIN 1835‑A and is manufactured to h8 tolerance to ensure secure clamping in standard collets and holders. What advantage does the TiN coating provide? The TiN coating on the TECWERK spot drill reduces friction and improves wear resistance, extending tool life under the thermal loads typical of NC spot‑drilling. Can centring and chamfering be completed in one pass? The geometry of this NC spot drill is designed to centre and chamfer threaded hole starts in a single operation, improving process efficiency and reducing handling. What feed values are recommended for reliable operation? For steel, the tool is specified with a feed of 0.03 mm/rev at loads up to 800 N; this setting supports stable cutting and consistent hole starts for NC production. Manufacturer/Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund
4mm NC Spot Drill Solid Carbide TiAlN Coated 142° Point, Cylindrical Shank DIN 6535-HA - TECWERK
Take advantage of solid carbide construction and TiAlN wear resistance combined with a 142° point angle for reliable, position-accurate centring and chamfering in one pass; order the tool directly via Metav Werkzeuge or contact the consultants for application advice. NC spot drill Ø4 mm, solid carbide, TiAlN coating — TECWERK A NC spot drill Ø4 mm designed for position-accurate and rapid spot drilling on CNC machines and drilling rigs, enabling centring and chamfering of thread holes in a single operation. Solid carbide, TiAlN coating 142° point for precise centring Cylindrical shank to DIN 6535-HA Suited for high-strength and stainless steels Longer tool life through hard-wearing materials The combination of solid carbide substrate with a TiAlN coating delivers superior wear resistance and thermal stability compared with uncoated tools. This increases tool life under intermittent and continuous operation and permits higher cutting parameters where the machine allows. Operators will notice fewer tool changes, reduced downtime and more consistent hole quality, as the protective coating helps resist abrasion and adhesion when machining abrasive or heat‑sensitive materials. Faster, more accurate centring and chamfering in one pass A 142° point angle and optimised geometry enable reliable centre formation and a controlled chamfer during a single cycle. The cylindrical shank DIN 6535-HA ensures rigid clamping and concentric running on CNC spindles and drilling rigs, improving repeatability and reducing runout. Combined with right-hand cutting and the specified feed behaviour, the design reduces secondary operations and shortens cycle time while maintaining hole position accuracy. Built for a wide range of demanding materials The tool is specifically prepared for machining high-strength steels, grey cast iron, stainless steels and non‑ferrous metals, making it a versatile choice for workshop and production environments. By providing a clean, centred entry, the spot drill stabilises subsequent twist drills and enhances thread formation. For materials requiring delicate heat control, the coated surface lowers friction and helps preserve edge geometry, supporting consistent performance across different alloys. Practical performance data and process benefits With an overall length of 50 mm and a spiral length of 12 mm, the configuration balances reach with rigidity for repeatable centring tasks. A recommended feed example is 0.06 mm/rev in steel up to 800 N, which gives a practical starting point for process setup; adjustments should be made according to machine capability and coolant use. The tool’s dimensions and h6 tolerance assist in predictable toolholders and accurate axial positioning, reducing setup time and scrap rates on precision jobs. Choose TECWERK precision for reliable centring: order via Metav Werkzeuge or request tailored application support from Metav Werkzeuge at info@metav-werkzeuge.com or +49 2822 7131930 Technical Data Article number: 2000865838NW Norm: DIN 6535-HA Manufacturer: TECWERK Facts Diameter: 4 mm Overall length: 50 mm Spiral length: 12 mm Point angle: 142° Feed in steel to 800 N: 0.06 mm/rev Tolerance diameter: h6 Special features Material: solid carbide Coating: TiAlN Shank: cylindrical shank to DIN 6535-HA Cutting direction: right-hand cutting Application: position-accurate and fast spot drilling on NC machines and drilling rigs Application: centring and chamfering of thread holes in one pass Suitable for: high-strength steels, cast steels, grey cast iron, stainless steel and non-ferrous metals Centres solid carbide drills with 120–140° point angle FAQ What materials can this spot drill machine reliably? The TECWERK NC spot drill is suited to high-strength steels, grey cast iron, stainless steel and a range of non‑ferrous metals, as stated in the technical features. Is the shank compatible with standard toolholders? Yes. The cylindrical shank complies with DIN 6535-HA, providing reliable clamping and concentricity for standard holders used on CNC machines and drilling rigs. What is the recommended feed for steel machining? A practical guideline is 0.06 mm/rev in steel up to 800 N; final settings should be adapted to machine stiffness, coolant and workpiece fixture. Can this spot drill prepare holes for subsequent solid carbide drills? Yes. The centring geometry provides an accurate starting point for twist drills; it is particularly compatible with solid carbide drills that have a 120–140° point angle. Which SKU identifies this item? The article number is 2000865838NW and the label references the TECWERK NC spot drill with TiAlN coating. Manufacturer/Responsible: NORDWEST Handel AG, Robert-Schuman-Straße 17, 44263 Dortmund
4mm NC Spot Drill Solid Carbide TiAlN Coated 90° Cylindrical Shank h6, DIN 6535-HA - TECWERK
Take advantage of the combination of solid carbide construction, TiAlN surface treatment and a 90° centring point for fast, positionally accurate spotting and chamfering on NC machines; order the tool directly via Metav Werkzeuge or consult the Metav team for application advice. NC spot drill D.4mm solid carbide TiAlN 90° TECWERK The NC spot drill D.4mm VHM TiAlN 90° TECWERK is a precision centre‑drilling tool for positionally accurate spotting, centring and chamfering on NC machines and drilling centres. Solid carbide with TiAlN coating 90° point for accurate centring Cylindrical shank to DIN 6535-HA Faster, more reliable positioning on CNC and NC equipment The combination of a solid carbide body and a TiAlN coating delivers high rigidity and improved heat resistance, which translates into consistent, repeatable spotting operations on modern CNC machines. The 90° point ensures fast and accurate centring before subsequent drilling or tapping; this reduces setup time and minimises rework. Designed for short-cycle production, the tool maintains positional integrity even under frequent use, helping to improve throughput without compromising hole quality. One‑pass centring and chamfering to streamline workflow With a geometry optimised for simultaneous centring and bevel formation, the spot drill removes the need for separate chamfering operations. The cylindrical shank to DIN 6535‑HA guarantees secure clamping in standard toolholders, while the short flute length allows precise control during entry. For operations that demand quick cycle times and repeatability, this approach reduces handling steps and contributes to a more efficient production flow. Engineered for demanding materials and stable feeds The tool is particularly suitable for high‑strength steels, cast steel, grey cast iron, stainless steels and non‑ferrous metals. The substrate and coating combination withstands elevated temperatures and abrasion in these materials, enabling a recommended feed of 0.06 mm/rev in steel at cutting forces up to 800 N. The right‑hand cutting action and controlled flute geometry help evacuate chips reliably, minimising the risk of built‑up edge and preserving hole integrity. Precision fit and repeatable tolerances for batch production A diameter tolerance of h6 ensures a consistent fit and repeatable centre positions across multiple components. The tool’s overall length and flute dimensions are balanced for rigidity and access: the overall length 50 mm with a spiral (flute) length 12 mm provides the necessary reach while keeping deflection low. These factors combine to deliver measurable accuracy gains in batch and serial manufacturing, supporting quality control and reducing scrap rates. Contact Metav Werkzeuge today to discuss application suitability for your production process or to arrange supply of the TECWERK NC spot drill; benefit from Metav’s precision expertise and reliable European distribution. Technical data Article number: 2000865811NW Norm: DIN 6535-HA Product type: NC spot drill Facts Diameter: 4 mm Overall length: 50 mm Spiral length: 12 mm Point angle: 90° Feed in steel (≤ 800 N): 0.06 mm/rev Tolerance: h6 Special features Solid carbide (VHM) TiAlN coating Cylindrical shank to DIN 6535‑HA Right‑hand cutting Designed for centring and chamfering in one pass Suitable for high‑strength steels, cast steel, grey cast iron, stainless steels and non‑ferrous metals FAQ What materials is the NC spot drill suitable for? The NC spot drill D.4mm VHM TiAlN 90° TECWERK is suitable for high‑strength steels, cast steel, grey cast iron, stainless steels and various non‑ferrous metals. How does the TiAlN coating benefit the tool performance? The TiAlN coating on the TECWERK spot drill increases thermal resistance and reduces wear, extending tool life and maintaining consistent centring quality under elevated cutting temperatures. What tolerance and shank standard does the tool use? The tool is manufactured with a diameter tolerance of h6 and a cylindrical shank conforming to DIN 6535‑HA for secure clamping and repeatable positioning. Can the tool perform chamfering and centring in a single operation? Yes, the geometry of the TECWERK NC spot drill enables precise centring and simultaneous chamfering of threaded holes in one pass, lowering cycle count. What spindle feed is recommended for steel applications? A feed of approximately 0.06 mm per revolution is indicated for steel at cutting forces up to 800 N when using this spot drill. Manufacturer/Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund
High-performance drill bits for demanding production
Drill bits designed for industrial manufacturing where precision, repeatability and tool life are decisive. Based on a spectrum from HSS and kobalt-alloyed hss-e for universal use to solid carbide drills for high-speed, high-precision serial production, this range covers applications from general engineering to automotive supplier work.
Why these drill bits are essential in the workshop and on the machining centre
Function and behaviour:
- primary use: creating accurate cylindrical holes
- typical machines: CNC machining centres, lathes and drill presses
- key design aspects: optimised chisel edge, defined point angles, flute geometry for reliable chip evacuation
Technical advantages and process benefits:
- reduced feed forces through optimised point geometry
- improved heat control with advanced coatings and, where specified, internal coolant supply
- extended tool life using solid carbide variants and multilayer coatings such as TiN / TiAlN
- process security on challenging materials thanks to tailored materials and geometries
Concrete benefits that boost productivity and quality
- predictable tool life and fewer tool changes, lowering machine downtime
- stable hole quality and consistent tolerances across long runs
- efficient chip control and thermal management for safe deep-hole and hardened-material drilling
- suitability across a wide material range, reducing the need for multiple specialised tools
Metav as a reliable partner for high-precision tooling
Metav combines decades of sector expertise with a broad, dependable offering from its Emmerich facility. With over 48,000 customers and more than 250,000 products, Metav positions its range of drill bits, twist drills and indexable drills as a practical, quality-first choice for procurement managers and production engineers seeking dependable supply and technical competence.
Technical data (at a glance)
- material: HSS, kobalt-alloyed hss-e, solid carbide
- coatings: TiN, TiAlN, advanced nanocoatings
- coolant option: internal coolant feed where specified
- typical applications: mild steel, high-alloy stainless steel, cast iron, non-ferrous metals, technical plastics, hardened materials (use solid carbide variants)
- tool types available: twist drills, solid carbide drills, indexable drills, centre and pilot drills, step drills
FAQ
What is the difference between hss and solid carbide drill bits?
HSS drill bits offer toughness and resistance to breakage for general machining, while solid carbide drills provide higher wear resistance and are the preferred choice for high-speed, high-volume machining and hardened materials.
Which coatings improve tool life for industrial drilling?
Coatings such as TiN and TiAlN increase surface hardness and thermal stability; when combined with the correct drill geometry and, if available, internal coolant, they significantly extend the service life of drill bits.
Can these drill bits be used on CNC machining centres for deep holes?
Yes. Drill bits designed with optimised flute geometry and internal coolant supply are suited to deep-hole machining on CNC machining centres, ensuring controlled chip evacuation and heat management.
How should I choose between twist drills, solid carbide drills and indexable drills?
Select twist drills for general-purpose drilling, solid carbide drills for high-speed and hardened-material applications, and indexable drills for large-diameter holes where insert changes offer economic advantages.
Why choose Metav for drill bits and drilling solutions?
Metav offers a comprehensive selection of drill bits, twist drills and indexable drills combined with sector expertise, centralised supply from Emmerich and proven reliability across thousands of industrial customers.
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com