Twist Drill Bits for Professionals: Quality You Can Rely On

Twist Drill Type N — 6.4 mm, 135°, short, 5% cobalt-alloyed, HSS‑E, DIN 338 The Twist Drill Type N is a short HSS‑E metal drill designed for precise work in Hand Drilling Machines and stationary setups. Short design for increased rigidity and accuracy 135° point angle for hard materials like stainless steel HSS‑E with 5% cobalt for improved heat resistance Fully ground shank for high concentricity and clean holes Compliant with DIN 338 for short twist drills Greater Precision through a Short, Stable Design The short configuration of this Twist Drill minimises overhang and produces higher stability during drilling, which directly benefits precision and reduces the risk of wandering. The fully ground Shank delivers excellent concentricity, resulting in cleaner, rounder holes in Metal. For operators seeking reproducible results on benches or in jigs, the reduced tendency to deflect means less rework and better fit for threaded components. Suited to Hard Materials — Faster Penetration, Better Control With a 135° Point Angle and the Type N Normal Spiral geometry, this short HSS‑E tool is optimised for demanding tasks in Steel, Cast Iron and other hard materials. The geometry shortens initial touch‑in time and helps maintain the centre when starting a hole. Compliance with DIN 338 indicates manufacture to accepted dimensions and tolerances for short twist drills, supporting consistent performance across batches and easy integration in production workflows. Practical Guidance for Efficient Use Use the Twist Drill in a suitable Drilling Machine with adequate clamping and coolant to extend tool life. The 5% cobalt-alloyed composition increases heat resistance, allowing for higher cutting temperatures and improved wear stability; nevertheless, coolant or lubricant is advised for continuous or deep drilling. The shorter overall length favours operations where stiffness and tool control are critical, such as drilling into thicker plates or working with tight positional tolerances. Material and Handling Benefits from HSS‑E Chemistry The HSS‑E grade combined with 5% cobalt yields a balance of hardness and toughness that performs well under thermal load. The Standard Line production and the fully ground flute geometry create sharp cutting edges and excellent runout characteristics. Operators should note that ground drills offer superior hole quality but can be more brittle than rolled alternatives; therefore, controlled feed rates and proper cooling will help prevent chipping and extend service intervals. Strong recommendation: Choose the MetavCUT short Twist Drill for demanding metal applications and contact METAV Werkzeuge for expert advice and personalised support — eMail: info@metav-werkzeuge.com · Phone: +49 2822 7131930 · WhatsApp: +49 170 2837271 Designation: Twist Drill Brand: MetavCUT SKU: 47064-FDA Type: Type N Diameter: 6.4 mm Point Angle: 135° Execution: short Overall Length: 101 mm Spiral Length: 63 mm Material: HSS‑E Colour / Surface: 5% cobalt-alloyed Shank: fully ground Application: Drills for metal For Drilling Machine: Drilling Machine Model Series: Standard Line Norm: DIN 338 Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What is the MetavCUT Twist Drill Type N used for? The MetavCUT Twist Drill Type N is primarily used for drilling Metal and is suitable for demanding applications where a short, stiff tool is required. It is especially effective on harder materials thanks to the 135° point angle and HSS‑E chemistry, which together improve centring and heat resistance. For what is a Twist Drill used? A Twist Drill is mainly applied to the machining of high‑strength materials and larger bore diameters. Its form allows relatively simple resharpening and it withstands higher loads. This geometry is commonly used where durability and the ability to drill tough materials are required. Which 3 drill types are there? Common classifications are Metal drills, Wood drills, and Masonry/Concrete drills. Why are Twist Drills point‑ground? Point grinding reduces the cross‑cut at the tip of the Twist Drill, which lowers friction and consequently the required feed forces. In addition, a ground tip improves centring in the workpiece and leads to more accurate, controlled drilling.

Spiralbohrer kurz, Durchmesser 6,4 mm, Spitzenwinkel 135°, Typ N, Farbe Blank, Ausführung geschliffen, Norm DIN 338, Material HSS‑G — MetavCUT Standard Line Der Spiralbohrer ist ein kurzer HSS‑G Metallbohrer nach DIN 338 und eignet sich für präzise Bohrungen in Stahl und Nichteisenmetallen mit Handbohrmaschine oder stationärer Aufnahme. Kurzbauform für hohe Stabilität Geschliffenes HSS‑G für saubere Bohrbilder 135° Spitzenwinkel ideal für Edelstahl Norm DIN 338, Zylinderschaft geschliffen Kompakte Bauform sorgt für präzise und verwindungsarme Bohrungen Die Kurzbauform reduziert die Auskraglänge und führt zu deutlich weniger Durchbiegung bei Belastung. Das Ergebnis sind präzise Bohrungen mit besserer Mittigkeit und geringerer Gefahr von Wanderungen an der Oberfläche. Anwender profitieren von erhöhter Seitenstabilität bei der Bearbeitung harter Werkstoffe, wodurch das Arbeiten mit Handbohrmaschine ebenso effizient gelingt wie auf stationären Maschinen. Geschliffenes HSS‑G und Geometrie für metallische Werkstoffe Das Material HSS‑G kombiniert Wärmebeständigkeit mit guter Zähigkeit, während die Geschliffen‑Ausführung durch CNC‑Schliff scharfe Schneiden und hohe Rundlaufgenauigkeit liefert. Der 135° Spitzenwinkel reduziert das Anbohren in harten Werkstoffen und sorgt für kontrollierten Spanabgang. Für Anwender bedeutet das: sauberere Bohrlöcher, weniger Nachbearbeitung und längere Standzeiten unter geeigneter Kühlung. Ideal für Werkstatt, Montage und Handbetrieb Mit einem Durchmesser von 6,4 mm liegt dieser Bohrer im Standard‑Bereich und ist für Werkstattarbeiten, Montage und DIY‑Projekte ausgelegt. Die Kombination aus kurzem Zylinderschaft und robuster Schneidkante macht den Einsatz in dünnen bis mittleren Blechen, Profilen sowie in Baustahl, Aluminium und Hartkunststoff möglich. Die Konstruktion erlaubt den Gebrauch in Handbohrmaschine sowie in stationären Bohrmaschinen mit stabiler Aufnahme. Anwendungshinweise für höhere Präzision und Standzeit Für bestmögliche Ergebnisse empfiehlt sich bei hoher Präzision ein kurzes Zentrieren vor dem Volldurchgang. Zentrieren und moderates Vorschubverhalten verringern die Belastung der Querschneide. Bei der Bearbeitung von Edelstahl und legierten Stählen ist die Nutzung von Kühlung oder Kühlschmierstoff ratsam, um Überhitzung und vorzeitigen Verschleiß zu vermeiden. Die Norm DIN 338 garantiert die Einordnung als kurzer Spiralbohrer mit Zylinderschaft und definiert Form sowie Fertigungsverfahren. MetavCUT Standard Line Kurzspiralbohrer (HSS‑G, geschliffen) empfiehlt sich für präzise Metallbohrungen in Werkstatt und Produktion — bei Fragen stehen wir Ihnen gerne zur Verfügung: info@metav-werkzeuge.com oder Telefon +49 2822 7131930 Bezeichnung: Spiralbohrer Marke: MetavCUT SKU: 45064-FDA Durchmesser: 6,4 mm Spitzenwinkel: 135° Typ: Typ N Farbe: Blank (bright finished) Material: HSS‑G Ausführung: kurz Schaft Ausführung: geschliffen Gesamtlänge: 101 mm Spirallänge: 63 mm Anwendung: Bohrer für Metall Für Bohrmaschine: Handbohrmaschine Modellserie: Standard Line Norm: DIN 338 Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ Was macht den Spiralbohrer von MetavCUT (Typ N) für Metall besonders geeignet? Der Spiralbohrer von MetavCUT (Typ N) kombiniert HSS‑G mit geschliffener Geometrie und einem 135° Spitzenwinkel, was saubere Bohrbilder und bessere Anbohreigenschaften in Stahl und Edelstahl ermöglicht. Kann ich den Spiralbohrer von MetavCUT (Typ N) in einer Handbohrmaschine verwenden? Ja, der Spiralbohrer von MetavCUT (Typ N) mit kurzem Zylinderschaft ist für Handbohrmaschine geeignet, empfiehlt sich aber vor allem bei stabiler Aufnahme für optimale Rundlaufgenauigkeit. Wie verbessere ich die Standzeit des Spiralbohrers von MetavCUT (Typ N)? Für längere Standzeit des Spiralbohrers von MetavCUT (Typ N) wird Kühlung oder Kühlschmierstoff sowie kontrollierter Vorschub empfohlen; bei harten Werkstoffen geringere Schnittgeschwindigkeit wählen. Ist der Spiralbohrer von MetavCUT (Typ N) nach einer Norm gefertigt? Ja, der Spiralbohrer von MetavCUT (Typ N) entspricht der DIN 338, die kurze Spiralbohrer mit Zylinderschaft klassifiziert und Fertigungsmerkmale definiert. {"@context":"https://schema.org","@graph":[{"@type":"Product","@id":"#45064-FDA","sku":"45064-FDA","mpn":"45064-FDA","name":"Spiralbohrer 45064-FDA","description":"Kurzspiralbohrer Durchmesser 6,4 mm, Spitzenwinkel 135°, Typ N, Farbe Blank, Ausführung geschliffen, Norm DIN 338, Material HSS‑G. Kurzbauform für hohe Stabilität; Geschliffenes HSS‑G für saubere Bohrbilder; Geeignet für Stahl und Nichteisenmetalle; Einsatz in Handbohrmaschine und stationären Maschinen.","image":["https://files.plytix.com/api/v1.1/file/public_files/pim/assets/57/c3/98/62/6298c3575d155f1bc7e497fd/images/8e/48/c5/69/69c5488eb2b3400ba580741b/logo-metav-1200-1200.png","https://files.plytix.com/api/v1.1/file/public_files/pim/assets/57/c3/98/62/6298c3575d155f1bc7e497fd/images/8e/48/c5/69/69c5488eb2b3400ba580741e/logo-metav-1200-900.png","https://files.plytix.com/api/v1.1/file/public_files/pim/assets/57/c3/98/62/6298c3575d155f1bc7e497fd/images/8e/48/c5/69/69c5488eb2b3400ba580741c/logo-metav-1200-675.png"],"additionalProperty":[{"@type":"PropertyValue","name":"Bezeichnung","value":"Spiralbohrer"},{"@type":"PropertyValue","name":"Marke","value":"MetavCUT"},{"@type":"PropertyValue","name":"SKU","value":"45064-FDA"},{"@type":"PropertyValue","name":"Durchmesser","value":"6,4 mm"},{"@type":"PropertyValue","name":"Spitzenwinkel","value":"135°"},{"@type":"PropertyValue","name":"Typ","value":"Typ N"},{"@type":"PropertyValue","name":"Farbe","value":"Blank"},{"@type":"PropertyValue","name":"Material","value":"HSS‑G"},{"@type":"PropertyValue","name":"Ausführung","value":"kurz"},{"@type":"PropertyValue","name":"Schaft Ausführung","value":"geschliffen"},{"@type":"PropertyValue","name":"Gesamtlänge","value":"101 mm"},{"@type":"PropertyValue","name":"Spirallänge","value":"63 mm"},{"@type":"PropertyValue","name":"Anwendung","value":"Bohrer für Metall"},{"@type":"PropertyValue","name":"Für Bohrmaschine","value":"Handbohrmaschine"},{"@type":"PropertyValue","name":"Modellserie","value":"Standard Line"},{"@type":"PropertyValue","name":"Norm","value":"DIN 338"},{"@type":"PropertyValue","name":"Hersteller","value":"Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com"}]},{"@type":"FAQPage","mainEntity":[{"@type":"Question","name":"Was macht den Spiralbohrer von MetavCUT (Typ N) für Metall besonders geeignet?","acceptedAnswer":{"@type":"Answer","text":"Der Spiralbohrer von MetavCUT (Typ N) kombiniert HSS‑G mit geschliffener Geometrie und einem 135° Spitzenwinkel, was saubere Bohrbilder und bessere Anbohreigenschaften in Stahl und Edelstahl ermöglicht."}},{"@type":"Question","name":"Kann der Spiralbohrer von MetavCUT (Typ N) in einer Handbohrmaschine verwendet werden?","acceptedAnswer":{"@type":"Answer","text":"Ja, der Spiralbohrer von MetavCUT (Typ N) mit kurzem Zylinderschaft ist für Handbohrmaschine geeignet, empfiehlt sich aber bei stabiler Aufnahme für optimale Rundlaufgenauigkeit."}},{"@type":"Question","name":"Wie lässt sich die Standzeit des Spiralbohrers von MetavCUT (Typ N) verbessern?","acceptedAnswer":{"@type":"Answer","text":"Zur Verbesserung der Standzeit des Spiralbohrers von MetavCUT (Typ N) wird Kühlung oder Kühlschmierstoff sowie ein kontrollierter Vorschub empfohlen; bei harten Werkstoffen sollte eine geringere Schnittgeschwindigkeit gewählt werden."}},{"@type":"Question","name":"Entspricht der Spiralbohrer von MetavCUT (Typ N) einer Norm?","acceptedAnswer":{"@type":"Answer","text":"Ja, der Spiralbohrer von MetavCUT (Typ N) entspricht der DIN 338, die kurze Spiralbohrer mit Zylinderschaft klassifiziert und Fertigungsmerkmale definiert."}}]},{"@type":"ItemPage","url":"https://metav-shop.de/produkt/45064-FDA","dateModified":"2026-05-04T12:00:00+01:00","author":{"@type":"Person","name":"Stephan Bayer","url":"https://www.linkedin.com/in/stephan-bayer/"},"publisher":{"@type":"Organization","name":"Metav Werkzeuge GmbH","url":"https://metav-shop.de","logo":{"@type":"ImageObject","url":"https://files.plytix.com/api/v1.1/file/public_files/pim/assets/57/c3/98/62/6298c3575d155f1bc7e497fd/images/8e/48/c5/69/69c5488eb2b3400ba580741c/logo-metav-1200-675.png","width":1200,"height":675},"address":{"@type":"PostalAddress","streetAddress":"Parkring 45","postalCode":"46446","addressLocality":"Emmerich","addressCountry":"DE"},"telephone":"+49 2822 7131930","email":"info@metav-werkzeuge.com"},"about":[{"@type":"Thing","name":"Kurzspiralbohrer nach DIN 338"},{"@type":"Thing","name":"Bohrer für Metall"},{"@type":"Thing","name":"HSS‑G geschliffen"}],"mentions":[{"@type":"Thing","name":"Einsatz in Handbohrmaschine"},{"@type":"Thing","name":"Einsatz in stationären Maschinen"},{"@type":"Thing","name":"Geeignet für legierte und unlegierte Stähle"}]}]}

MetavCUT Twist Drill — Twist Drill, 6.4 mm, 135°, Type N, Bright Finished, Short, DIN 338, HSS-G A MetavCUT Twist Drill for precision metalworking, the short 6.4 mm Type N cutter delivers stable, fast drilling in hard materials Short design for increased stability and precision 6.4 mm Diameter for accurate metal drilling 135° Tip angle optimised for hard materials HSS-G Material with fully ground geometry Conforms to DIN 338 for standardised quality Engineered for faster, more stable metal drilling The MetavCUT Twist Drill in a short execution combines a compact overall length with a reduced overhang to deliver higher stability and less tendency to deflect. Manufactured from HSS‑G (high speed steel, ground), the bit features a precision ground flute geometry that produces clean holes and reduces cutting forces. The short geometry yields up to 40% faster drilling and requires significantly less feed pressure compared with conventional HSS versions, making it especially suitable for demanding tasks in workshops and production environments. DIN 338 classifies this type of short twist drill with a cylindrical shank, ensuring compatibility with standard chucks and consistent manufacturing tolerances. Optimised tip geometry for hard and alloyed materials A 135° tip angle reduces the initial bite and improves centring in tougher metals such as stainless steel and alloyed steels, shortening contact time and improving tool life. Type N (normal spiral) provides a balanced flute helix suitable for metalworking, while the fully ground shank guarantees excellent concentricity and low runout when mounted in a drilling machine or hand drill. For users less familiar with the terminology: HSS‑G denotes that the cutting geometry is produced by grinding rather than rolling, which results in very sharp cutting edges and high hole quality; however, the ground structure is generally more brittle and benefits from adequate cooling during prolonged operations. Practical benefits, target users and safe handling tips Workshop technicians, maintenance staff and professional machinists will appreciate the combination of short overhang and robust HSS‑G material for producing precise bores in cast iron, sintered parts, non‑ferrous metals and hard plastics. When using the drill in handheld applications, reduced flex leads to fewer broken drills and a more predictable drilling result. To avoid premature breakage, apply moderate pecking cycles on deep holes, use coolant for heat dissipation and clamp workpieces securely. If there is uncertainty whether this cutter matches specific requirements or when additional technical data is needed, Metav Werkzeuge provides extensive and competent advice and support. Strong recommendation: Choose the MetavCUT short HSS‑G Twist Drill (Type N) for demanding metal applications — for expert consultation contact METAV Werkzeuge by eMail at info@metav-werkzeuge.com, by phone at +49 2822 7131930 or via WhatsApp at +49 170 2837271 Technical specifications Designation: Twist Drill Brand: MetavCUT SKU: 48064-FDA Model series: Profi Line Diameter: 6.4 mm Spiral length: 63 mm Overall length: 101 mm Tip angle: 135° Type: Type N Execution: Short Shank execution: Fully ground Finish / Colour: Bright finished Material: HSS-G Application: Drills for metal Suitable for: Drilling Machine / Hand drill Standard: DIN 338 Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What is a Twist Drill used for? The MetavCUT Twist Drill (Type N) is primarily used for machining high‑strength materials and larger bore diameters; its short, ground geometry makes it well suited to precise metalworking. This form is relatively easy to re‑sharpen and withstands significant loads while delivering clean bores, which is why it is often the tool of choice for workshops working with alloyed and unalloyed steel, cast iron and similar materials. Which three drill types are commonly distinguished? In general practice the main drill categories are metal drills, wood drills and stone/concrete drills; the MetavCUT Twist Drill belongs to the metal drill group and is optimised for metalworking tasks.

Spiralbohrer (kurz) – HSS, 6,5 mm, 118°, Typ N, schwarz, DIN 338 von MetavCUT Der Spiralbohrer ist ein kurzer HSS-Bohrer nach DIN 338, entwickelt für präzise Metallbohrungen mit 6,5 mm Durchmesser in Werkstatt und Montage. Spiralbohrer MetavCUT HSS für Metallbohrungen Kurze Ausführung für hohe Stabilität 6,5 mm Durchmesser, Spitzenwinkel 118° Typ N Normalspirale für Stahl und Eisen Geeignet für Handbohrmaschine und Werkstatt Mehr Präzision durch kurze Bauart und stabile Ausführung Die kurze Ausführung reduziert Auslenkung und erhöht die Stabilität beim Bohren, was besonders bei mittleren Durchmessern wie 6,5 mm zu saubereren Bohrungen führt. Durch die kompakte Geometrie wird das Risiko von Vibrationen verringert, sodass die Maschine- und Werkstückbelastung sinkt und die Bohrung innerhalb enger Toleranzen bleibt. Dies macht den Einsatz besonders effizient für wiederkehrende Montage- und Instandsetzungsarbeiten. Materialeigenschaften und Normverständnis für sichere Auswahl Der Einsatz von HSS (High Speed Steel) sorgt für gute Zähigkeit und Verschleißfestigkeit bei typischen Metallbearbeitungen. Die Norm DIN 338 definiert die kurze Spiralbohrer-Ausführung mit Zylinderschaft und gibt Hinweise zu Abmessungen und Toleranzen. Kunden profitieren von der Normkonformität durch verlässliche Austauschbarkeit und Planbarkeit bei Maschinen- und Spannmittelauswahl. Einsatzgebiete und Maschineneignung für zuverlässige Ergebnisse Mit 6,5 mm Durchmesser liegt der Bohrer im Standard-Bereich für Alltagsaufgaben in Werkstatt und Montage. Der Typ N mit Normalspirale ist ausgelegt für Stahl, Eisen, Gusseisen sowie Nichteisenmetalle und Kunststoffe und eignet sich für den Einsatz in Handbohrmaschine und stationären Bohrmaschinen. Für besonders harte oder tiefgehende Arbeiten sind Vorbohren und abgestimmte Kühlschmierstoffe empfehlenswert, um Standzeit und Oberflächenqualität zu erhöhen. Praktische Hinweise für sicheres und effizientes Bohren Vor dem Bohren empfiehlt sich Anpunktieren mit einem Zentrierbohrer, um Wandern beim Anbohren zu vermeiden. Bei Stahl und legierten Werkstoffen reduziert ein geeigneter Kühlschmierstoff Wärmeentwicklung und verschlechterte Schneidbedingungen. Die kurze Länge und Spirallänge sorgen für eine gute Spanabfuhr bei üblichen Lochtiefen; dennoch sollten Bohrtiefen über das Fünffache des Durchmessers mit geeigneter Technik geplant werden. Technische Daten kompakt Die nachfolgenden Daten fassen die wesentlichen Angaben zusammen und geben eine schnelle Orientierung für Einkauf und Maschinenauswahl. Sollten zusätzliche Informationen oder Prüfzertifikate benötigt werden, steht METAV Werkzeuge gern beratend zur Seite. Bezeichnung: Spiralbohrer Marke: MetavCUT SKU: 40065-FDA Material: HSS Norm: DIN 338 Typ: Typ N (Normalspirale) Durchmesser: 6,5 mm Spitzenwinkel: 118° Ausführung: kurz Farbe: schwarz Gesamtlänge: 101 mm Spirallänge: 63 mm Für Bohrmaschine: Handbohrmaschine Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com Empfehlung: Setzen Sie auf den kurzen MetavCUT HSS-Bohrer für präzise Metallbearbeitung und kontaktieren Sie METAV Werkzeuge bei Fragen oder für ergänzende technische Daten per eMail info@metav-werkzeuge.com oder Telefon +49 2822 7131930 FAQ Welche Materialien lassen sich mit dem Spiralbohrer von MetavCUT bearbeiten? Der Spiralbohrer von MetavCUT als HSS-Bohrer eignet sich vor allem für unlegierten und legierten Stahl, Gusseisen sowie Nichteisenmetalle und Kunststoffe; bei sehr harten Werkstoffen ist eine angepasste Schnittstrategie erforderlich. Ist der MetavCUT Spiralbohrer für die Handbohrmaschine geeignet? Ja, der MetavCUT Spiralbohrer in kurzer Ausführung und mit 6,5 mm Durchmesser ist für den Einsatz in Handbohrmaschine sowie in stationären Bohrmaschinen konzipiert und bietet gute Stabilität bei typischen Werkstattaufgaben. Worauf ist beim Einsatz des HSS-Bohrers Typ N zu achten? Beim HSS-Bohrer Typ N von MetavCUT empfiehlt sich Anpunktierung und bei Stahl die Nutzung eines Kühlschmierstoffs; für tiefe Löcher oder gehärtete Materialien sind abgestimmte Werkzeugstrategien notwendig. Wie beeinflusst der Spitzenwinkel von 118° die Bohrleistung? Der Spitzenwinkel 118° beim MetavCUT Spiralbohrer sorgt für leichtes Eindringen und gutes Zentrierverhalten in weicheren bis mittleren Metallen; für sehr harte Werkstoffe kann ein größerer Winkel vorteilhaft sein. {"@context":"https://schema.org","@graph":[{"@type":"Product","@id":"#40065-FDA","sku":"40065-FDA","mpn":"40065-FDA","name":"Spiralbohrer 40065-FDA","description":"Kurzer HSS-Spiralbohrer Typ N, 6,5 mm Durchmesser, Spitzenwinkel 118°, schwarz, DIN 338; geeignet für Metallbohrungen in Werkstatt und Montage, hohe Stabilität durch kurze Ausführung.","image":["https://files.plytix.com/api/v1.1/file/public_files/pim/assets/57/c3/98/62/6298c3575d155f1bc7e497fd/images/8e/48/c5/69/69c5488eb2b3400ba580741b/logo-metav-1200-1200.png","https://files.plytix.com/api/v1.1/file/public_files/pim/assets/57/c3/98/62/6298c3575d155f1bc7e497fd/images/8e/48/c5/69/69c5488eb2b3400ba580741e/logo-metav-1200-900.png","https://files.plytix.com/api/v1.1/file/public_files/pim/assets/57/c3/98/62/6298c3575d155f1bc7e497fd/images/8e/48/c5/69/69c5488eb2b3400ba580741c/logo-metav-1200-675.png"],"additionalProperty":[{"@type":"PropertyValue","name":"Bezeichnung","value":"Spiralbohrer"},{"@type":"PropertyValue","name":"Marke","value":"MetavCUT"},{"@type":"PropertyValue","name":"Material","value":"HSS"},{"@type":"PropertyValue","name":"Norm","value":"DIN 338"},{"@type":"PropertyValue","name":"Typ","value":"Typ N (Normalspirale)"},{"@type":"PropertyValue","name":"Durchmesser","value":"6,5 mm"},{"@type":"PropertyValue","name":"Spitzenwinkel","value":"118°"},{"@type":"PropertyValue","name":"Ausführung","value":"kurz"},{"@type":"PropertyValue","name":"Farbe","value":"schwarz"},{"@type":"PropertyValue","name":"Gesamtlänge","value":"101 mm"},{"@type":"PropertyValue","name":"Spirallänge","value":"63 mm"},{"@type":"PropertyValue","name":"Für Bohrmaschine","value":"Handbohrmaschine"},{"@type":"PropertyValue","name":"Anwendung","value":"Bohrer für Metall"},{"@type":"PropertyValue","name":"Hersteller","value":"Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com"}]},{"@type":"FAQPage","mainEntity":[{"@type":"Question","name":"Welche Materialien lassen sich mit dem Spiralbohrer von MetavCUT bearbeiten?","acceptedAnswer":{"@type":"Answer","text":"Der Spiralbohrer von MetavCUT als HSS-Bohrer eignet sich vor allem für unlegierten und legierten Stahl, Gusseisen sowie Nichteisenmetalle und Kunststoffe; bei sehr harten Werkstoffen ist eine angepasste Schnittstrategie erforderlich."}},{"@type":"Question","name":"Ist der MetavCUT Spiralbohrer für die Handbohrmaschine geeignet?","acceptedAnswer":{"@type":"Answer","text":"Ja, der MetavCUT Spiralbohrer in kurzer Ausführung und mit 6,5 mm Durchmesser ist für den Einsatz in Handbohrmaschine sowie in stationären Bohrmaschinen konzipiert und bietet gute Stabilität bei typischen Werkstattaufgaben."}},{"@type":"Question","name":"Worauf ist beim Einsatz des HSS-Bohrers Typ N zu achten?","acceptedAnswer":{"@type":"Answer","text":"Beim HSS-Bohrer Typ N von MetavCUT empfiehlt sich Anpunktierung und bei Stahl die Nutzung eines Kühlschmierstoffs; für tiefe Löcher oder gehärtete Materialien sind abgestimmte Werkzeugstrategien notwendig."}},{"@type":"Question","name":"Wie beeinflusst der Spitzenwinkel von 118° die Bohrleistung?","acceptedAnswer":{"@type":"Answer","text":"Der Spitzenwinkel 118° beim MetavCUT Spiralbohrer sorgt für leichtes Eindringen und gutes Zentrierverhalten in weicheren bis mittleren Metallen; für sehr harte Werkstoffe kann ein größerer Winkel vorteilhaft sein."}}]},{"@type":"ItemPage","url":"https://metav-shop.de/spiralbohrer-40065-FDA","dateModified":"2026-05-04T12:00:00+01:00","author":{"@type":"Person","name":"Stephan Bayer","url":"https://www.linkedin.com/in/stephan-bayer/"},"publisher":{"@type":"Organization","name":"Metav Werkzeuge GmbH","url":"https://metav-shop.de","logo":{"@type":"ImageObject","url":"https://files.plytix.com/api/v1.1/file/public_files/pim/assets/57/c3/98/62/6298c3575d155f1bc7e497fd/images/8e/48/c5/69/69c5488eb2b3400ba580741c/logo-metav-1200-675.png","width":1200,"height":675},"address":{"@type":"PostalAddress","streetAddress":"Parkring 45","postalCode":"46446","addressLocality":"Emmerich","addressCountry":"DE"},"telephone":"+49 2822 7131930","email":"info@metav-werkzeuge.com"},"about":[{"@type":"Thing","name":"Spiralbohrer Kurze Ausführung"},{"@type":"Thing","name":"HSS Schnellarbeitsstahl"},{"@type":"Thing","name":"DIN 338 Klassifikation"}],"mentions":[{"@type":"Thing","name":"Typ N Normalspirale"},{"@type":"Thing","name":"Anwendung: Metallbohrung"},{"@type":"Thing","name":"Empfohlen: Anpunktieren und Kühlschmierstoff"}]}]}

Twist Drill — Type N, 6.5 mm, 135° tip, short, 5% cobalt-alloyed, HSS‑E, DIN 338 The Twist Drill Type N is a short HSS‑E metalworking drill designed for stable, precise holes in hard materials when used with a Drilling Machine. Short construction for increased stability 6.5 mm diameter for standard metalwork 135° tip for clean penetration in hard steels 5% cobalt‑alloyed HSS‑E for enhanced wear resistance Fully ground shank for high concentricity Durable alloy and compact design for demanding metalwork The HSS‑E composition with 5% cobalt gives this short twist drill exceptional heat resistance and wear stability when machining tough alloys. Because the design is short, the tool exhibits reduced overhang and less flexing, which directly improves hole accuracy and tool life under heavy cutting loads. This makes the drill particularly suitable for precision tasks such as locating holes in jigs and producing repeatable diameters in alloyed and unalloyed steel. Geometry and finish that improve hole quality and centring A fully ground flute geometry yields very sharp cutting edges and excellent concentricity; the typical result is cleaner chips and reduced burr formation. The 135° tip angle reduces thrust and improves entry in hard materials such as stainless steel, shortening the initial contact phase and helping to avoid wandering. As a Type N normal‑spiral twist drill, it balances chip evacuation and cutting stability for general metalworking. Recommended applications and suitable materials This short Twist Drill is engineered for use in metalworking: it performs well on alloyed and unalloyed steel, cast iron, non‑ferrous metals and many plastics. The compact length is an asset when working with hand or bench drilling machines where rigidity is crucial. Note that Type N geometry is not optimised for very soft woods; for woodworking, specialist drills provide better guidance and surface finish. Handling, cooling and reconditioning advice for longer life To maintain performance, use appropriate cutting speeds and a cutting fluid when machining steels; cooling reduces tool wear and the risk of tempering the cutting edge. Because the drill is manufactured ground, it can be resharpened by a skilled operator to restore the cutting lip and prolong service life. Observing correct feed and speed settings for the material ensures reliable hole quality and minimises breakage risk. We recommend MetavCUT’s Twist Drill Type N for precise metalworking — for personal technical advice or to confirm suitability for your application, contact METAV Werkzeuge: info@metav-werkzeuge.com | +49 2822 7131930 | WhatsApp +49 170 2837271 Designation: Twist Drill Marke: MetavCUT SKU: 47065-FDA Diameter: 6.5 mm Tip angle: 135° Spiral length: 63 mm Overall length: 101 mm Execution: short Type: Type N Material: HSS‑E Colour: 5% cobalt‑alloyed Shank finish: fully ground Model series: Standard Line Norm: DIN 338 For machine: Drilling Machine Application: Drills for metal Manufacturer: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What is the Twist Drill Type N best used for? The MetavCUT Twist Drill Type N is primarily used for metalworking; it excels when drilling alloyed and unalloyed steels, cast iron and other hard materials, offering good general performance on rotating drilling machines. Can the MetavCUT Twist Drill be used in a hand drilling machine? Yes, the short design of the MetavCUT Twist Drill makes it especially stable in hand and bench Drilling Machines, reducing the tendency to bend and improving hole accuracy when correct speeds and cooling are applied. What are Twist Drills used for? Twist Drills are mainly applied when machining high‑strength materials and larger diameters. Their form allows relatively simple resharpening and they withstand higher loads, making them suitable for robust metalworking tasks. Which three drill types exist? The three primary drill categories are metal drills, wood drills and stone/concrete drills.

Karosseriebohrer (Body Drill) — HSS-G Twist Drill, 6.5 mm Diameter, 135° Tip, Double-sided, Black Finished Without Margin The Karosseriebohrer (Body Drill) is a double-sided HSS-G Twist Drill designed for precise metalworking with a 6.5 mm diameter and a 135° tip angle for demanding sheet and body applications. Double-sided twist drill for two usable cutting ends HSS-G material for precise metal drilling 6.5 mm Diameter with 135° Tip Angle Fully ground shank for high runout accuracy Black finished without margin for corrosion resistance Faster, more precise holes in hard metals The HSS-G construction and 135° tip angle are chosen to reduce drilling time and minimise feed force when working with tougher materials. Because the flute geometry is produced by CNC grinding rather than rolling, the Karosseriebohrer delivers high runout accuracy and clean hole edges, which is particularly valuable when preparing parts for riveting or welding. The sharper cutting edges also help extend tool life when used with appropriate cooling on stationary machines. Compact, double-ended design for workshop efficiency Designed as a double-sided / double-ended Twist Drill, this bit offers practical redundancy: if one tip becomes dull, simply reverse the bit and continue using the other end. The short, stable geometry suits thin-sheet and bodywork tasks and reduces vibration in hand and drilling machines. With a fully ground shank, clamping stability is improved, supporting consistent concentricity and safer operation in portable Drilling Machines. Where this drill performs best This Karosseriebohrer is optimised for metal drilling: alloyed and unalloyed steel, cast materials, non-ferrous metals and hard plastics. The 6.5 mm diameter and the chosen tip geometry make it particularly effective for holes used in body and panel work, rivet preparation and general maintenance tasks. Professionals in automotive repair, sheet metal workshops and maintenance departments will benefit from reliable entry behaviour and consistent hole quality. Handling, sharpening and application hints Because the flute geometry is ground, the twist drill requires careful handling: avoid aggressive impact and favour cooling when machining heat-sensitive or tougher cast materials to prevent premature chipping. If a tip becomes blunt, the double-ended design allows quick reversal; resharpening is possible but should respect the original 135° geometry to retain centring and cutting performance. Use steady feed and appropriate cutting fluid for best results with the HSS-G material. Strong recommendation from MetavCUT: choose this Karosseriebohrer for demanding metalwork where precision and durability matter — and contact METAV Werkzeuge for expert advice on application and tool selection; 📧 info@metav-werkzeuge.com ☎️ +49 2822 7131930 ✔️ WhatsApp: +49 170 2837271 Technical information Designation: Body Drill (Karosseriebohrer) Brand: MetavCUT SKU: 59065-FDA Material: HSS-G Diameter: 6.5 mm Tip Angle: 135° Type / Execution: double-sided Colour / Finish: black finished without margin Suitable for: Drilling Machine (Hand Drills / Portable Drilling Machines) Spiral Length: 20 mm Overall Length: 70 mm Shank Execution: fully ground Model Series: Profi Line Application: Drills for metal Packaging Unit: 10 Manufacturer: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What materials can the Karosseriebohrer (Body Drill) from MetavCUT drill effectively? The Karosseriebohrer by MetavCUT is suitable for alloyed and unalloyed Steel, Cast Steel, Gusseisen, sintered materials, non-ferrous metals and hard plastics, providing clean results when used with appropriate cutting fluid and machine speeds. Is the Karosseriebohrer suitable for use in a hand drill? Yes, the Karosseriebohrer (Body Drill) is designed for use with Drilling Machines including hand-held units, though optimal precision and cooling are achieved on stationary machines to reduce risk of breakage. For what is a Twist Drill used? A Twist Drill is primarily used for machining high-strength materials and larger bore diameters; its form is easy to sharpen and withstands significant loads, making it common in bodywork and sheet-metal applications. Which three drill types exist? The main categories are Metal drill bits, Wood drill bits, and Stone/Concrete drill bits. Why are Twist Drills sharpened? Sharpening reduces the cross cutting edge at the tip, which lowers friction and required feed force while improving centring of the tip in the workpiece. Can you use a metal drill to drill wood? A metal drill can be used in wood, but guidance and finish are inferior compared with purpose-made wood bits; metal drill bits are easier to resharpen and generally have less self-feed. At which drilling depths is the Twist Drill most commonly used? A solid bore is typically made with a Twist Drill; for diameters up to 20 mm and depths up to 100 mm the Twist Drill is the most frequently used tool. What is better, HSS or HSSE? The general assumption that HSSE is always superior to HSS is not correct; selection should consider working conditions and whether the higher acquisition cost of HSSE is justified.

Karosseriebohrer — Body Drill, 6.5 mm, 135° tip, double sided, Bright Finished, HSS‑G, Fully Ground Shank The Karosseriebohrer is a double sided Body Drill designed for Drilling Machine applications, delivering precise metal drilling with a 135° tip and a Fully Ground HSS‑G geometry for tough materials. Double-ended design for twice the usable life HSS‑G ground geometry for precise metal drilling 135° tip for harder materials such as stainless steel Fully ground shank for improved runout accuracy Bright finish for corrosion resistance and visual inspection Exceptional Material Performance and Cutting Efficiency The Karosseriebohrer from MetavCUT combines a HSS‑G composition with CNC grinding to produce extremely sharp Cutting Edges and a consistent Spiral Geometry. This Ground Manufacturing method yields high Roundness Accuracy and clean, burr‑reduced holes in metals. The optimized geometry enables up to 40% faster drilling and requires up to 50% less thrust compared with conventional HSS variants, which directly reduces operator fatigue and cycle times in production environments. Built for Harder Materials and Reliable Hole Entry A 135° Tip Angle reduces walking and improves centring when working with tougher substrates like Stainless Steel, Cast Steel and other alloyed Steels. The double ended layout makes the Tool inherently more compact and stable, a design often favoured in bodywork and Sheet Metal operations where short, accurate holes are critical. Because the Bit can be reversed when one end dulls, downtime for tool changes is minimized while precision remains high. Precision Features That Support Workshop Standards The Fully Ground Shank and Bright Finished surface support consistent Tool Runout and easy visual inspection. Ground Flute Geometry creates clean chip evacuation and precise chip formation, resulting in smoother hole walls and less rework. Note that Ground HSS grades can be more brittle than rolled equivalents, so cooling and sensible feed rates are recommended for station‑type drilling and high‑duty cycles to extend Tool Life. Practical Application, Handling and Suitability This Body Drill is intended for Drilling Machine usage across a range of metals including unalloyed and alloyed Steel, Cast Iron variants and Non‑Ferrous Metals, as well as Hard Plastics. The double‑ended Twist Drill design is particularly suitable for workshop and industrial settings where short, precise holes are required and quick tool rotation between ends increases uptime. For hand tool operations, ensure compatible chucks and take appropriate safety measures. We recommend the MetavCUT Standard Line Karosseriebohrer for professionals requiring fast, accurate metal drilling; METAV Werkzeuge offers expert advice and technical support—contact via info@metav-werkzeuge.com or +49 2822 7131930 for tailored recommendations and application guidance Designation: Karosseriebohrer / Body Drill Brand: MetavCUT SKU: 58065-FDA Diameter: 6.5 mm Tip Angle: 135° Spiral Length: 20 mm Overall Length: 70 mm Execution: double sided Shank Execution: fully ground Material: HSS‑G For Drilling Machine: Drilling Machine Colour: Bright Finished Model Series: Standard Line Application: Drills for metal Manufacturer: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What is the best application for the Karosseriebohrer Body Drill by MetavCUT? The Karosseriebohrer Body Drill from MetavCUT is primarily used for precise metalwork, especially where short, accurate holes are required in Sheet Metal and Bodywork components; its double‑ended Twist Drill design and HSS‑G grinding make it suitable for alloyed and unalloyed Steel, Cast Iron, Non‑Ferrous Metals and Hard Plastics. Can the Karosseriebohrer Body Drill by MetavCUT be used in hand drills? Although the Karosseriebohrer Body Drill by MetavCUT is optimised for Drilling Machine applications, it can be used in appropriately rated Hand Drills if the chuck and operational parameters match the Tool requirements; for best results and safety, check recommended speeds and cooling. For what are Twist Drills used? A Twist Drill such as the Karosseriebohrer Body Drill by MetavCUT is mainly applied to the machining of high‑strength materials and larger hole diameters; the shape is easy to regrind and stands up to higher loads, making it a common choice for robust metalworking tasks. Which three drill types exist? Typical categories include Metal Drill, Wood Drill and Stone/Concrete Drill; the Karosseriebohrer by MetavCUT belongs to the Metal Drill family and is designed for demanding metal applications. Why are Twist Drills point‑sharpened? Point sharpening reduces the cross‑edge at the tip of a Twist Drill; for the Karosseriebohrer Body Drill by MetavCUT this lowers friction, reduces required feed force and improves centring, leading to cleaner holes and more controlled drilling. Can a Metal Drill be used for wood? A Metal Drill such as the Karosseriebohrer by MetavCUT can be used in Wood, but it typically offers poorer guidance and a less clean finish than a dedicated Wood Drill; regrindability and lower self‑feed may be advantageous for specific tasks. For which drilling depths is the Twist Drill most used? The Twist Drill design is commonly used for through‑holes and solid drilling; for diameters up to around 20 mm and depths up to approximately 100 mm a Twist Drill like the Karosseriebohrer Body Drill by MetavCUT is often the preferred tool. Is HSS or HSSE better for my application? The general belief that HSSE is always superior to HSS is not universally correct; evaluate whether the working conditions for the Karosseriebohrer Body Drill by MetavCUT require the additional cost of HSSE, considering cutting speed, material and coolant use before deciding.

Twist Drill — Drill Bit, 6.5 mm, 135° point angle, extra-long, bright-finished, HSS-G, DIN 1869 A Twist Drill Drill Bit for deep metal drilling, optimised for Drilling Machines and hand-held drills. Extra-long geometry for deep drilling HSS-G material for high wear resistance 135° tip for harder materials Fully-ground shank for precise runout Conforms to DIN 1869 for demanding conditions Engineered for accurate, high-performance metal cutting This HSS-G Twist Drill combines a ground flute geometry with a high-speed-steel alloy to deliver clean, precise holes in tough materials. The CNC grinding process produces very sharp cutting edges and high concentricity, which reduces vibration and improves surface finish. As a result, drilling in alloyed and unalloyed steel, cast iron and non-ferrous metals becomes noticeably more consistent, while the reduced required feed force eases operator handling and minimises tool deflection. Deep holes and secured centring for demanding tasks Designed with an extra-long overall length and an extended spiral length, the geometry allows access to recessed or hard-to-reach positions without sacrificing stability. The 135° point angle is optimised for harder materials and shortens the initial plunge time while improving centring and chip evacuation. With a total length of 215 mm and a flute length of 150 mm, the bit is particularly suitable where standard lengths are insufficient and deep through-holes or extended reaches are required. Built for workshops, maintenance and production environments Manufactured for users who need reliable performance in metalworking, this Drill Bit suits machine shops, maintenance departments and on-site technicians working with steels up to 1000 N/mm². Compliance with DIN 1869 ensures reproducible quality and compatibility with industrial processes. The bright-finished surface supports easy visual inspection and handling on the shop floor while the fully-ground shank improves clamping accuracy in chucks and collets. Handling advice to maximise life and performance Because ground Twist Drills can be more prone to shock than rolled types, controlled machining parameters are recommended. Use appropriate cutting speeds, steady feed and coolant when drilling deep or hard materials to avoid thermal overload and chipping. If working with stainless or high-strength steels, the 135° tip and HSS-G composition reduce the tendency to work-harden; nevertheless, intermittent peck drilling or backing-off is advised for chip control during long bores. Regular inspection and resharpening extend service life while maintaining hole quality. Opt for the MetavCUT extra-long HSS-G Twist Drill for reliable deep-hole performance — for technical advice and application support contact METAV Werkzeuge by eMail at info@metav-werkzeuge.com, by phone at +49 2822 7131930 or via WhatsApp at +49 170 2837271 Designation: Twist Drill Brand: MetavCUT SKU: 32065-FDA Diameter: 6,5 mm Point angle: 135° Overall length: 215 mm Spiral length: 150 mm Execution: extra long Shank execution: fully ground Colour: bright finished For drilling machine: Drilling Machine / Hand Drill Material: HSS-G Model series: Standard Line Norm: DIN 1869 Application: Drills for metal Story trigger: bohrer UID: 32065-FDA Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What is this Twist Drill by MetavCUT best used for? The MetavCUT Twist Drill Drill Bit is primarily designed for drilling in metals; it excels in alloyed and unalloyed steel, cast iron and non-ferrous metals where deep, precise holes are required. Its HSS-G composition and ground geometry make it suitable for demanding workshop and production applications. Can the MetavCUT Twist Drill be used with a hand-held drill? Yes, the Twist Drill by MetavCUT is suitable for use in both Drilling Machines and hand-held drills, though for very deep or high-precision holes a machine-mounted setup with coolant and steady feed is recommended. For what are Twist Drills used? Twist Drills are mainly applied to the machining of high-strength materials and large-diameter drilling. Their geometry allows efficient chip removal and, when sharpened correctly, they withstand higher loads and cutting forces. Which three drill types exist? The three common drill types are metal drills, wood drills and stone/concrete drills. Why are Twist Drills point-ground (ausgespitzt)? Point-grinding reduces the cross-cutting edge at the tip, significantly lowering friction and required feed forces. It also improves the drill’s centring ability in the workpiece. Can a metal drill be used for wood? A metal drill can be used in wood, but guidance is poorer and the hole finish is typically less clean. Metal drills are easier to resharpen and have less self-feed than dedicated wood bits. For which drilling depths is the Twist Drill most used? A Twist Drill is commonly used for solid drilling. It is the most frequently used tool for diameters up to 20 mm and drilling depths up to 100 mm in many workshop settings.

Spiralbohrer 6,5 mm | HSS‑G extra lang, blank, geschliffen, DIN 1869 Der Spiralbohrer ist ein extra langer HSS‑G Spiralbohrer für Metall mit 6,5 mm Durchmesser und 135° Spitzenwinkel, konzipiert für tiefe Löcher und anspruchsvolle Werkstoffe. Spiralbohrer 6,5 mm HSS‑G extra lang nach DIN 1869 Tieflochspirale für extra tiefe Metallbohrungen Geschliffener Schaft für hohe Rundlaufgenauigkeit 135° Spitzenwinkel für härtere Werkstoffe wie Edelstahl Bis zu 40 % schnelleres Bohren bei reduzierter Anpresskraft Überlegene Schnittleistung durch geschliffene HSS‑Geometrie Dank HSS‑G und geschliffener Fertigung liefert dieser Bohrer eine deutlich schärfere Schneide als gewalzte Varianten. Das Ergebnis ist ein sauberer Spanfluss und eine höhere Rundlaufgenauigkeit, was besonders bei Metallbohrungen die Nachbearbeitung reduziert. Anwender profitieren von einem bis zu 40 % schnelleren Vorschub und einer um rund 50 % geringeren Anpresskraft im Vergleich zu herkömmlichen HSS‑Bohrern, wodurch Arbeitszyklen effizienter gestaltet werden. Speziell für extra tiefe Metallbohrungen konstruiert Die Tieflochspirale und die verlängerte Arbeitslänge (Spirallänge 190 mm, Gesamtlänge 275 mm) ermöglichen das Bohren deutlich tieferer Löcher ohne sofortiges Verstopfen durch Späne. Diese Konstruktion erleichtert das Abführen von Spänen und reduziert das Blockier- beziehungsweise Verruckungsrisiko bei tiefen Durchführungen. Für Anwendungen in Gussstahl, Sinterteilen oder dicken Blechen schafft die Bauart verlässliche Voraussetzungen für wiederholbare Ergebnisse. Einsatzbereich und Maschineneignung für sichere Anwendungen Mit einem Durchmesser von 6,5 mm fällt der Bohrer in den Standard‑Bereich und ist für Werkstatt, Montage und DIY‑Projekte geeignet. Der Bohrer eignet sich für Handbohrmaschinen ebenso wie für stationäre Säulenbohrmaschinen, liefert aber die besten Ergebnisse bei gleichmäßigem Vorschub und Kühlung. Für präzise Passungen empfiehlt es sich, vorzuprüfen und gegebenenfalls mit einem Zentrierbohrer anzupunkten, um Seitenwandwandern zu vermeiden. Praktische Hinweise für Langlebigkeit und sichere Handhabung Da der Bohrer geschliffen ist, bietet er hohe Präzision, kann aber bei unsachgemäßer Nutzung empfindlicher reagieren als walzgeformte Varianten. Empfohlen werden mäßige Drehzahlen, konstante Kühlung und gelegentliches Zurückziehen zur Spanabfuhr. Bei Arbeiten in härteren Werkstoffen sorgt der 135° Spitzenwinkel für ein kontrolliertes Anbohren und geringere Wanderneigung. Empfehlung: Den MetavCUT Spiralbohrer mit HSS‑G und Tieflochspirale wählen, um tiefe Metallbohrungen effizient, präzise und zuverlässig auszuführen — bei Unsicherheiten oder Fragen berät METAV Werkzeuge gern persönlich per eMail info@metav-werkzeuge.com, Telefon +49 2822 7131930 oder WhatsApp +49 170 2837271 Bezeichnung: Spiralbohrer Marke: MetavCUT SKU: 33065-FDA Durchmesser: 6,5 mm Material: HSS-G Ausführung: extra lang Farbe: blank Schaft Ausführung: geschliffen Spitzenwinkel: 135° Spirallänge: 190 mm Gesamtlänge: 275 mm Norm: DIN 1869 Für Bohrmaschine: Handbohrmaschine Modellserie: Standard Line Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ Für welche Materialien ist der Spiralbohrer von MetavCUT geeignet? Der Spiralbohrer von MetavCUT (HSS‑G, 6,5 mm) eignet sich für legierten und unlegierten Stahl, Gussstahl, Gusseisen, Sintereisen, Temperguss, Nichteisenmetalle sowie Hartkunststoff; bei sehr harten Werkstoffen ist auf passende Drehzahl und Kühlung zu achten. Kann der Spiralbohrer 6,5 mm von MetavCUT in einer Handbohrmaschine verwendet werden? Ja, der Spiralbohrer 6,5 mm von MetavCUT ist für den Einsatz mit Handbohrmaschine geeignet; für beste Ergebnisse bei tiefen Bohrungen empfiehlt sich ein stationäres Vorgehen oder stabile Spannaufnahme. Wie vermeide ich Bruch bei dem geschliffenen Spiralbohrer von MetavCUT? Um Bruch zu vermeiden, sollte der geschliffene Spiralbohrer von MetavCUT mit moderater Drehzahl, kontinuierlicher Kühlung und ohne übermäßigen Vorschub betrieben werden und bei tiefen Bohrungen regelmäßig zur Spanabfuhr zurückgezogen werden. Warum ist der 135° Spitzenwinkel beim MetavCUT Spiralbohrer vorteilhaft? Der 135° Spitzenwinkel des MetavCUT Spiralbohrers reduziert das Anlaufen und verbessert die Standzeit beim Bohren härterer Werkstoffe wie Edelstahl, wodurch das Anbohren kontrollierter und präziser gelingt. {"@context":"https://schema.org","@graph":[{"@type":"Product","@id":"#33065-FDA","sku":"33065-FDA","mpn":"33065-FDA","name":"Spiralbohrer 6,5 mm HSS-G extra lang","description":"Extra langer Spiralbohrer 6,5 mm HSS-G nach DIN 1869 mit Tieflochspirale, geschliffenem Schaft und 135° Spitzenwinkel; konzipiert für tiefe Metallbohrungen in legierten und unlegierten Stählen, Gussstahl, Gusseisen, Sintereisen, Temperguss, Nichteisenmetallen und Hartkunststoffen.","image":["https://files.plytix.com/api/v1.1/file/public_files/pim/assets/57/c3/98/62/6298c3575d155f1bc7e497fd/images/8e/48/c5/69/69c5488eb2b3400ba580741c/logo-metav-1200-675.png","https://files.plytix.com/api/v1.1/file/public_files/pim/assets/57/c3/98/62/6298c3575d155f1bc7e497fd/images/8e/48/c5/69/69c5488eb2b3400ba580741b/logo-metav-1200-1200.png","https://files.plytix.com/api/v1.1/file/public_files/pim/assets/57/c3/98/62/6298c3575d155f1bc7e497fd/images/8e/48/c5/69/69c5488eb2b3400ba580741e/logo-metav-1200-900.png"],"additionalProperty":[{"@type":"PropertyValue","name":"Bezeichnung","value":"Spiralbohrer"},{"@type":"PropertyValue","name":"Durchmesser","value":"6,5 mm"},{"@type":"PropertyValue","name":"Material","value":"HSS-G"},{"@type":"PropertyValue","name":"Ausführung","value":"extra lang"},{"@type":"PropertyValue","name":"Farbe","value":"blank"},{"@type":"PropertyValue","name":"Schaft Ausführung","value":"geschliffen"},{"@type":"PropertyValue","name":"Spitzenwinkel","value":"135°"},{"@type":"PropertyValue","name":"Spirallänge","value":"190 mm"},{"@type":"PropertyValue","name":"Gesamtlänge","value":"275 mm"},{"@type":"PropertyValue","name":"Norm","value":"DIN 1869"},{"@type":"PropertyValue","name":"Für Bohrmaschine","value":"Handbohrmaschine"},{"@type":"PropertyValue","name":"Modellserie","value":"Standard Line"},{"@type":"PropertyValue","name":"Hersteller","value":"MetavCUT"}],"author":{"@type":"Person","name":"Stephan Bayer","url":"https://www.linkedin.com/in/stephan-bayer/"},"publisher":{"@type":"Organization","name":"Metav Werkzeuge GmbH","url":"https://metav-shop.de","logo":{"@type":"ImageObject","url":"https://files.plytix.com/api/v1.1/file/public_files/pim/assets/57/c3/98/62/6298c3575d155f1bc7e497fd/images/8e/48/c5/69/69c5488eb2b3400ba580741c/logo-metav-1200-675.png","width":1200,"height":675},"address":{"@type":"PostalAddress","streetAddress":"Parkring 45","postalCode":"46446","addressLocality":"Emmerich","addressCountry":"DE"},"telephone":"+49 2822 7131930","email":"info@metav-werkzeuge.com"},"about":[{"@type":"Thing","name":"Tieflochspirale"},{"@type":"Thing","name":"Geschliffener Schaft"},{"@type":"Thing","name":"135° Spitzenwinkel"}]},{"@type":"FAQPage","mainEntity":[{"@type":"Question","name":"Für welche Materialien ist der Spiralbohrer von MetavCUT geeignet?","acceptedAnswer":{"@type":"Answer","text":"Der Spiralbohrer 6,5 mm HSS-G von MetavCUT eignet sich für legierten und unlegierten Stahl, Gussstahl, Gusseisen, Sintereisen, Temperguss, Nichteisenmetalle sowie Hartkunststoff; bei sehr harten Werkstoffen sind passende Drehzahl und Kühlung empfehlenswert."}},{"@type":"Question","name":"Kann der Spiralbohrer 6,5 mm HSS-G von MetavCUT in einer Handbohrmaschine verwendet werden?","acceptedAnswer":{"@type":"Answer","text":"Ja, der Spiralbohrer 6,5 mm HSS-G von MetavCUT kann in einer Handbohrmaschine verwendet werden; für sehr tiefe Bohrungen sind stationäre Maschinen oder eine stabile Spannaufnahme für beste Ergebnisse zu bevorzugen."}},{"@type":"Question","name":"Wie vermeide ich Bruch bei dem geschliffenen Spiralbohrer von MetavCUT?","acceptedAnswer":{"@type":"Answer","text":"Um Bruch zu vermeiden, sollte der geschliffene Spiralbohrer 6,5 mm HSS-G von MetavCUT mit moderater Drehzahl, kontinuierlicher Kühlung und ohne übermäßigen Vorschub betrieben werden; bei tiefen Bohrungen regelmäßig zur Spanabfuhr zurückziehen."}},{"@type":"Question","name":"Warum ist der 135° Spitzenwinkel beim MetavCUT Spiralbohrer vorteilhaft?","acceptedAnswer":{"@type":"Answer","text":"Der 135° Spitzenwinkel des MetavCUT Spiralbohrers reduziert das Anlaufen und erhöht die Standzeit beim Bohren härterer Werkstoffe wie Edelstahl, wodurch das Anbohren kontrollierter und präziser gelingt."}}]},{"@type":"ItemPage","url":"https://metav-shop.de/spiralbohrer-6-5mm-hss-g-extra-lang","dateModified":"2026-05-04T12:00:00+01:00","author":{"@type":"Person","name":"Stephan Bayer","url":"https://www.linkedin.com/in/stephan-bayer/"},"publisher":{"@type":"Organization","name":"Metav Werkzeuge GmbH","url":"https://metav-shop.de","logo":{"@type":"ImageObject","url":"https://files.plytix.com/api/v1.1/file/public_files/pim/assets/57/c3/98/62/6298c3575d155f1bc7e497fd/images/8e/48/c5/69/69c5488eb2b3400ba580741c/logo-metav-1200-675.png","width":1200,"height":675},"address":{"@type":"PostalAddress","streetAddress":"Parkring 45","postalCode":"46446","addressLocality":"Emmerich","addressCountry":"DE"},"telephone":"+49 2822 7131930","email":"info@metav-werkzeuge.com"},"about":[{"@type":"Thing","name":"Bohrer für Metall"},{"@type":"Thing","name":"Extra tiefe Bohrungen"},{"@type":"Thing","name":"HSS-G geschliffen"}],"mentions":[{"@type":"Thing","name":"MetavCUT"},{"@type":"Thing","name":"DIN 1869"},{"@type":"Thing","name":"Handbohrmaschine"}]}]}

Twist Drill — 6.5 mm, 135° Point Angle, Extra Long, Bright Finished, HSS‑G, DIN 1869 The Twist Drill is an extra‑long HSS‑G drill designed for deep metal drilling with a 135° point angle and a bright finished, fully ground shank for high precision in demanding machining tasks. Extra‑long design for deep bore reach 6.5 mm Diameter with 235 mm Spiral Length 135° Point Angle for harder materials Fully ground (HSS‑G) for high runout accuracy Complies with DIN 1869 for demanding conditions Durable HSS‑G construction for precise metalwork The drill is made from HSS‑G, a high‑speed steel that is CNC‑ground to achieve sharp cutting edges and excellent roundness. This fully ground geometry reduces vibration and produces cleaner holes in alloys and hard materials. For users this means fewer reworks and better repeatability when machining components that require tight tolerances. Extra‑long geometry solves deep drilling challenges With an extra‑long overall length of 350 mm and a spiral (flute) length of 235 mm, this tool reaches deeper bore positions where standard drills cannot. The elongated design allows comfortable access in hard‑to‑reach setups and reduces the need for extensions. The 135° point angle shortens entry time in tougher steels and improves centring when starting a hole. Performance advantages and recommended machining practice Compared with standard HSS tools, the ground HSS design can deliver up to 40% faster drilling and requires less axial force, improving operator comfort and machine load. The Twist Drill by MetavCUT is intended primarily for drilling legiertem und unlegiertem Stahl, Gussstahl, Gusseisen, Nichteisenmetalle and hard plastics; use adequate coolant and reduced feed rates at greater depths to minimise breakage risk and extend tool life. Who benefits and how to get support Manufacturers, toolrooms and maintenance teams that demand long reach and high precision will find this Twist Drill particularly suitable. For stationary or machine‑based work, the bright finish and precise geometry ensure consistent hole quality. If uncertain whether this tool meets specific requirements or for complementary technical data, METAV Werkzeuge offers expert advice and application support. Contact METAV Werkzeuge for customised recommendations and assistance with feed, speed and coolant selection. I recommend the MetavCUT extra‑long HSS‑G Twist Drill for any deep metal drilling task that requires precision and enhanced tool life — for personalised advice contact METAV Werkzeuge at info@metav-werkzeuge.com or call +49 2822 7131930; WhatsApp +49 170 2837271 Designation: Twist Drill Brand: MetavCUT SKU: 34065-FDA Diameter: 6.5 mm Point angle: 135° Type / Execution: Extra long Finish / Colour: Bright finished Spiral length (Flute length): 235 mm Overall length: 350 mm Shank execution: Fully ground Material: HSS‑G Applicable machines: Drilling Machine (Hand drill suitable with precautions) Application: Drills for metal Model series: Standard Line Standard / Norm: DIN 1869 Manufacturer: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What is the Twist Drill used for and which materials suit it best? The Twist Drill from MetavCUT (Twist Drill) is mainly used for machining high‑strength materials and larger hole diameters; it is especially suitable for alloyed and unalloyed steel, cast steel, cast iron, non‑ferrous metals and hard plastics thanks to its HSS‑G composition and ground geometry. Can the MetavCUT Twist Drill be used for deep holes and what makes it suitable? Yes, the MetavCUT Twist Drill is designed for deep bores; its extra‑long overall length and a 235 mm spiral length, combined with the DIN 1869 Tieflochspirale, make it ideal for bore depths and difficult access situations. For what is a Twist Drill used? A Twist Drill is primarily applied when machining high‑strength materials and large hole diameters. Its shape allows easy resharpening and the ground geometry endures substantial loads, making it suitable for demanding metalworking. Which 3 drill types are there? Commonly distinguished drill types are: Metal drill (Metal drill), Wood drill (Wood drill), and Masonry/Concrete drill (Stone/Concrete drill). Why are Twist Drills pointed? Pointing reduces the cross‑edge at the drill tip; by pointing the Twist Drill the friction forces at the tip are substantially lowered, which requires less feed force and improves centring of the drill in the workpiece. Can a Twist Drill be used to drill wood? A metal Twist Drill can be used in wood but guidance and finish are inferior compared with dedicated wood drills. The MetavCUT Twist Drill can cut wood, yet results are less clean and the tool may have more tendency to pull itself in. For which depths is the Twist Drill most commonly used? A through hole in solid material is commonly executed with a Twist Drill. For diameters up to 20 mm and drilling depths up to 100 mm, the Twist Drill is the most frequently used tool. What is better, HSS or HSSE? The general belief that HSSE steels are universally superior to HSS is incorrect. Evaluate whether your working conditions justify the higher purchase cost of HSSE; for many applications HSS‑G (ground HSS) as used in the MetavCUT Twist Drill offers an optimal balance of performance and economy.

Spiralbohrer HSS-G 6,5 mm, 135°, Typ N, extra kurz, blank, DIN 1897 Der Spiralbohrer ist ein extra kurzer HSS-G-Bohrer für präzise Metallbohrungen mit hoher Stabilität in Handbohrmaschinen. Extra kurze Ausführung für beengte Einbausituationen HSS-G-Material für langlebige Schnittkante 135° Spitzenwinkel für härtere Werkstoffe Zylinderschaft: universell einspannbar im Dreibackenfutter DIN 1897 Norm für verlässliche Standardlänge und Qualität Robuste Schneidkante für effizientes Bohren in Stahl und Guss Der geschliffene HSS-G-Werkstoff sorgt für eine hohe Verschleißfestigkeit und eine langlebige Schneidkante, sodass der Bohrer auch bei wiederholten Einsätzen seine Leistung behält. Durch den 135° Spitzenwinkel dringt die Schneide leichter in härtere Werkstoffe ein, was die Anbohrzeit reduziert und Ausschuss minimiert. Dieser Vorteil macht den Bohrer zur wirtschaftlichen Wahl für Arbeiten in legiertem Stahl, Gussstahl und Temperguss, ohne aufwendige Nachbearbeitung. Kurze Bauform erhöht Stabilität und reduziert Bruchrisiko Die extra kurz ausgeführte Bauform verringert die Hebelwirkung und erhöht die Verdrehungsfestigkeit gegenüber längeren Ausführungen, was besonders bei Handgeführten Maschinen wichtig ist. In Kombination mit der kompakten Spirallänge wird die Späneförderung bei flachen Bohrungen optimiert, wodurch weniger Verkantungen auftreten. Anwender profitieren von höherer Präzision und einer deutlich geringeren Bruchneigung, speziell bei dünnen Blechen und Profilen. Passgenau für den Alltag: Handbohrmaschine, Profile und Bleche Dieser Bohrer richtet sich an Handwerker, Monteure und Hobbyanwender, die regelmäßig Metall bearbeiten und dabei auf unkomplizierte, universelle Lösungen setzen. Die Zylinderschaft ermöglicht das Einspannen in normale Dreibackenfutter und vereinfacht den Wechsel zwischen Maschinen. Für Anwendungen in Nichteisenmetallen und Hartkunststoff bietet der Bohrer saubere Ausfräsungen; bei Edelstahl und sehr harten Werkstoffen empfiehlt sich angepasste Schnittgeschwindigkeit und Kühlung. Hinweise zur Anwendung und Vorteile der Normausführung Die Fertigung nach DIN 1897 garantiert reproduzierbare Maße und erleichtert die Planung in Werkstatt und Produktion. Die kompakte Standard Line Ausführung ist besonders geeignet für Vorbohrungen und Reparaturarbeiten, bei denen Raum begrenzt ist. Durch die Kombination aus Materialwahl, Spitzengeometrie und Kurzlänge wird ein bis zu 40 % schnelleres Bohren sowie eine geringere Anpresskraft erreicht, wodurch Ermüdung beim Arbeiten reduziert und die Effizienz gesteigert wird. Empfehlung: Für präzise Metallbohrungen die MetavCUT Standard Line nutzen und bei technischen Fragen die kompetente Beratung von METAV Werkzeuge in Anspruch nehmen – per eMail info@metav-werkzeuge.com oder Telefon +49 2822 7131930, auch per WhatsApp +49 170 2837271 erreichbar Technische Daten Bezeichnung: Spiralbohrer Marke: MetavCUT SKU: 56065-FDA Durchmesser: 6,5 mm Spitzenwinkel: 135° Typ: Typ N Material: HSS-G Ausführung: extra kurz Farbe: blank Schaftausführung: Zylinder Gesamtlänge: 70 mm Spirallänge: 31 mm Norm: DIN 1897 Für Bohrmaschine: Handbohrmaschine Modellserie: Standard Line Verpackungseinheit: 10 Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ Ist der Spiralbohrer von MetavCUT für Edelstahl geeignet? Der Spiralbohrer von MetavCUT (Typ N) mit 135° Spitzenwinkel ist für härtere Werkstoffe wie Edelstahl geeignet, sofern die Schnittgeschwindigkeit reduziert und Kühlung eingesetzt wird, um Überhitzung und vorzeitigen Verschleiß zu vermeiden. Kann der extra kurze Bohrer in einer Handbohrmaschine verwendet werden? Ja, der extra kurz ausgeführte Spiralbohrer ist speziell für den Einsatz in Handbohrmaschinen vorgesehen und bietet durch die reduzierte Länge erhöhte Stabilität bei Handanwendung. Welchen Vorteil bietet die Zylinderschaft beim Spiralbohrer MetavCUT? Die Zylinderschaft des Spiralbohrers erlaubt das einfache Einspannen in gängige Dreibackenfutter, was den schnellen Werkzeugwechsel und die universelle Einsetzbarkeit im Alltag erleichtert. Warum ist die Norm DIN 1897 wichtig für diesen Bohrer? Die Herstellungsweise nach DIN 1897 gewährleistet definierte Maßhaltigkeit und Kompatibilität mit Einspannungen und Bohrprozessen, wodurch Planbarkeit und Ersatzteilmanagement in Werkstätten verbessert werden. {"@context":"https://schema.org","@graph":[{"@type":"Product","@id":"#56065-FDA","sku":"56065-FDA","mpn":"56065-FDA","name":"Spiralbohrer 6,5 mm Typ N extra kurz","description":"Spiralbohrer HSS-G 6,5 mm, 135°, Typ N, extra kurz, blank, DIN 1897. Extra kurze Ausführung für beengte Einbausituationen; HSS-G-Material für langlebige Schneidkante; 135° Spitzenwinkel für härtere Werkstoffe; Zylinderschaft universell einspannbar im Dreibackenfutter; geeignet für Handbohrmaschine und Arbeiten in Stahl, Guss und Nichteisenmetallen.","image":["https://files.plytix.com/api/v1.1/file/public_files/pim/assets/57/c3/98/62/6298c3575d155f1bc7e497fd/images/8e/48/c5/69/69c5488eb2b3400ba580741b/logo-metav-1200-1200.png","https://files.plytix.com/api/v1.1/file/public_files/pim/assets/57/c3/98/62/6298c3575d155f1bc7e497fd/images/8e/48/c5/69/69c5488eb2b3400ba580741e/logo-metav-1200-900.png","https://files.plytix.com/api/v1.1/file/public_files/pim/assets/57/c3/98/62/6298c3575d155f1bc7e497fd/images/8e/48/c5/69/69c5488eb2b3400ba580741c/logo-metav-1200-675.png"],"additionalProperty":[{"@type":"PropertyValue","name":"Bezeichnung","value":"Spiralbohrer"},{"@type":"PropertyValue","name":"Durchmesser","value":"6,5 mm"},{"@type":"PropertyValue","name":"Spitzenwinkel","value":"135°"},{"@type":"PropertyValue","name":"Typ","value":"Typ N"},{"@type":"PropertyValue","name":"Farbe","value":"blank"},{"@type":"PropertyValue","name":"Ausführung","value":"extra kurz"},{"@type":"PropertyValue","name":"Norm","value":"DIN 1897"},{"@type":"PropertyValue","name":"Material","value":"HSS-G"},{"@type":"PropertyValue","name":"Schaftausführung","value":"Zylinder"},{"@type":"PropertyValue","name":"Gesamtlänge","value":"70 mm"},{"@type":"PropertyValue","name":"Spirallänge","value":"31 mm"},{"@type":"PropertyValue","name":"Für Bohrmaschine","value":"Handbohrmaschine"},{"@type":"PropertyValue","name":"Modellserie","value":"Standard Line"},{"@type":"PropertyValue","name":"Verpackungseinheit","value":"10"}]},{"@type":"FAQPage","mainEntity":[{"@type":"Question","name":"Ist der Spiralbohrer von MetavCUT für Edelstahl geeignet?","acceptedAnswer":{"@type":"Answer","text":"Der Spiralbohrer MetavCUT 6,5 mm Typ N ist für härtere Werkstoffe wie Edelstahl geeignet, wenn die Schnittgeschwindigkeit reduziert und Kühlung eingesetzt wird, um Überhitzung und vorzeitigen Verschleiß zu vermeiden."}},{"@type":"Question","name":"Kann der extra kurze Spiralbohrer in einer Handbohrmaschine verwendet werden?","acceptedAnswer":{"@type":"Answer","text":"Ja, der extra kurz ausgeführte Spiralbohrer MetavCUT ist speziell für den Einsatz in Handbohrmaschinen konzipiert und bietet durch die reduzierte Länge erhöhte Stabilität bei Handanwendung."}},{"@type":"Question","name":"Welchen Vorteil bietet die Zylinderschaft beim Spiralbohrer MetavCUT?","acceptedAnswer":{"@type":"Answer","text":"Die Zylinderschaft des Spiralbohrers MetavCUT erlaubt das einfache Einspannen in gängige Dreibackenfutter, was schnellen Werkzeugwechsel und universelle Einsetzbarkeit erleichtert; bei sehr hohem Drehmoment kann er allerdings eher durchrutschen als 3‑Kant‑Schaftvarianten."}},{"@type":"Question","name":"Warum ist die Norm DIN 1897 wichtig für diesen Bohrer?","acceptedAnswer":{"@type":"Answer","text":"Die Fertigung nach DIN 1897 gewährleistet definierte Maßhaltigkeit und Kompatibilität mit Einspannungen und Bohrprozessen, was Planbarkeit und Ersatzteilmanagement in Werkstätten verbessert."}}]},{"@type":"ItemPage","url":"https://metav-shop.de","dateModified":"2026-05-04T12:00:00+01:00","author":{"@type":"Person","name":"Stephan Bayer","url":"https://www.linkedin.com/in/stephan-bayer/"},"publisher":{"@type":"Organization","name":"Metav Werkzeuge GmbH","url":"https://metav-shop.de","logo":{"@type":"ImageObject","url":"https://files.plytix.com/api/v1.1/file/public_files/pim/assets/57/c3/98/62/6298c3575d155f1bc7e497fd/images/8e/48/c5/69/69c5488eb2b3400ba580741c/logo-metav-1200-675.png","width":1200,"height":675},"address":{"@type":"PostalAddress","streetAddress":"Parkring 45","postalCode":"46446","addressLocality":"Emmerich","addressCountry":"DE"},"telephone":"+49 2822 7131930","email":"info@metav-werkzeuge.com"},"about":[{"@type":"Thing","name":"Spiralbohrer HSS-G"},{"@type":"Thing","name":"Standard Line"},{"@type":"Thing","name":"Bohrer für Metall"}],"mentions":[{"@type":"Thing","name":"Zylinderschaft"},{"@type":"Thing","name":"DIN 1897 Norm"},{"@type":"Thing","name":"135° Spitzenwinkel"},{"@type":"Thing","name":"Extra kurz Bauform"}]}]}

Twist Drill — Left-cutting HSS-G, Ø 6.5 mm, 135° (DIN 338) by MetavCUT The Twist Drill is a left-cutting metal drill for Drilling Machines and Hand Drills, designed for efficient removal of broken screws and demanding work in alloyed and unalloyed steels. Left-cutting design for reverse rotation drilling Ø 6.5 mm for precise metal bores 135° tip angle for hard materials HSS-G material for long tool life Conforms to DIN 338 short twist drill standard Fast, low-effort drilling in tough materials Engineered for professional metalworking, the Twist Drill uses a left-cutting grind that enables drilling in reverse rotation to assist in removing broken or seized screws. The combination of HSS-G steel and a 135° tip angle reduces penetration resistance in hard materials such as stainless steel. As a result, users benefit from faster drilling and reduced operator strain while maintaining clean bore starts. Durable construction and standardised dimensions for reliable results Manufactured to DIN 338, this short twist drill features a cylindrical shank and robust geometry for consistent performance in stationary and portable machines. The HSS-G composition ensures wear resistance under frequent use and delivers predictable life cycles, making the tool a dependable choice where durability matters most. Optimised for metalworking and specialised reverse tasks The left-cutting execution is specifically suited to metal applications and tasks that profit from a counterclockwise cut, such as extracting screw remnants. For proper operation the Twist Drill should be used in a Drilling Machine or Hand Drill capable of left rotation. This specialised grind also improves centring and reduces lateral forces during initial engagement. Designed for professionals seeking speed and control Targeted at mechanics, maintenance technicians and metalworking professionals, the Profi Line twist drills combine precision Ø 6.5 mm sizing with a geometry tuned for throughput and stability. The tool allows quicker cycle times and steadier feed, which translates into higher workshop productivity without compromising hole quality. METAV Werkzeuge provides expert advice and application support for complex requirements. Strong recommendation: Choose the MetavCUT Profi Line Twist Drill for demanding metalwork and contact METAV Werkzeuge for personalised technical consultation — 📧 info@metav-werkzeuge.com ☎️ +49 2822 7131930 ✔️ WhatsApp +49 170 2837271 Designation: Twist Drill Brand: MetavCUT SKU: 60065-FDA Diameter: 6.5 mm Tip angle: 135° Execution: Left-cutting (linksschneidend) For machine: Drilling Machine / Hand Drill Material: HSS-G Standard: DIN 338 Series: Profi Line Application: Drills for metal Notes: Left-cutting design aids extraction of broken screws; left-cut HSS drill enables up to 40% faster drilling and requires up to 50% less feed force compared to conventional HSS drills; suitable for alloyed and unalloyed steel, cast steel, cast iron, sintered iron, malleable cast iron, non-ferrous metals and hard plastics Manufacturer: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What is the MetavCUT Twist Drill used for? The MetavCUT Twist Drill is primarily applied in machining high-strength materials and larger bore diameters; its left-cutting grind is particularly effective for removing broken screws and for metalworking where reverse rotation provides advantages. The design is easy to resharpen and withstands higher loads. Which three drill types exist? Drill types are generally categorised as metal drills, wood drills and stone/concrete drills; the MetavCUT Twist Drill belongs to the metal drill category and differs from wood and masonry variants in geometry and cutting edge design.

Introducing Twist Drill Type N (Short) — 6.5 mm · 135° · HSS-G · Bright Finished · DIN 338 The Twist Drill is a short Type N drill designed for precise metalworking with a 6.5 mm diameter, optimised for Drilling Machine applications. Short Type N Twist Drill for precise metal work HSS‑G material: faster drilling, less feed force 135° tip for harder materials such as stainless steel Fully ground shank for improved concentricity Conforms to DIN 338 for short cylindrical drills Faster penetration and lower feed force for demanding metalwork The HSS‑G construction delivers a clear performance advantage: up to 40% faster drilling and approximately 50% lower feed force compared with conventional HSS tools. This means less operator strain and reduced wear on both tool and machine when processing alloyed and unalloyed steel, cast steel and non‑ferrous metals. The 135° Tip is optimised for tougher materials, shortening dwell on the surface and improving centring on curved or hardened parts. For workshop environments where efficiency and repeatability matter, this design converts technical properties into measurable productivity gains. Short design for superior stability and precise holes Built to the DIN 338 definition of a short cylindrical drill, the reduced overhang of the Short version greatly increases rigidity and reduces bending. The shorter exposed length results in improved concentricity and less vibration during operation, which translates into cleaner hole geometry and longer tool life. Where tight tolerances are required, the reduced tendency to deflect ensures repeatable results even at larger diameters and higher spindle speeds. This stability makes the tool particularly suitable for stationary and portable Drilling Machine setups that demand both accuracy and throughput. Shank, finish and practical advantages at a glance The Fully Ground Shank provides excellent concentricity and secure clamping in chucks, while the Bright Finished surface aids chip evacuation and visual inspection for wear. With a Spiral Length of 63 mm and an overall length of 101 mm, the geometry balances cutting capacity and strength for common metalworking tasks. The Type N normal spiral is the classic geometry for metal drilling and is straightforward to resharpen, which keeps replacement costs down and simplifies workshop maintenance routines. These characteristics combine to offer a robust solution for professional metalworkers seeking a reliable, easy‑to‑use drill bit. Strong recommendation: choose the MetavCUT Twist Drill Type N short in HSS‑G for precision metal drilling; for technical advice or to confirm suitability for specific applications, METAV Werkzeuge offers expert consultation — Email: info@metav-werkzeuge.com · Phone: +49 2822 7131930 · WhatsApp: +49 170 2837271 Technical details Designation: Twist Drill Marke: MetavCUT SKU: 27065-FDA Diameter: 6.5 mm Tip angle: 135° Type: Type N Execution: Short Material: HSS-G Spiral length: 63 mm Overall length: 101 mm Shank execution: Fully ground Colour / Finish: Bright finished Application: Drills for metal Standard: DIN 338 Model series: Basic Line Manufacturer: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What is the Twist Drill used for and which materials suit it best? The MetavCUT Twist Drill Type N (Short) is primarily used for drilling high‑strength materials and larger diameters in metalworking. Designed for metal, this short HSS‑G drill excels when machining alloyed and unalloyed steel, cast steel, cast iron, sintered iron, tempered castings, non‑ferrous metals and hard plastics; its geometry and material make it resilient under greater loads. Which three drill types exist? Commonly distinguished drill types are Metal drill, Wood drill and Masonry/Concrete drill. The MetavCUT Twist Drill belongs to the Metal drill category and is optimised for metalworking tasks.

Spiralbohrer 6,5 mm, 135° Spitzenwinkel, Typ N, HSS-G, kurze Ausführung, blank, DIN 338, MetavCUT Der Spiralbohrer 6,5 mm ist ein kurzer, geschliffener HSS-G Bohrer für Metallanwendungen und bietet hohe Stabilität und präzise Bohrungen in legierten und unlegierten Stählen sowie Gusswerkstoffen. Spiralbohrer 6,5 mm, kurze Ausführung HSS-G geschliffen für präzise Metallbohrungen 135° Spitzenwinkel für harte Werkstoffe DIN 338: kurze Spiralbohrer mit Zylinderschaft Bis zu 40 % schnelleres Bohren, weniger Anpresskraft Mehr Effizienz und Stabilität beim Metallbohren Dank HSS-G Material und CNC-geschliffener Geometrie liefert dieser Bohrer spürbar höhere Schnittleistung: Der geschliffene Schliff sorgt für scharfe Kanten und verbessert den Spanabtransport, was zu bis zu 40 % schnellerem Bohren und 50 % weniger Anpresskraft gegenüber herkömmlichen HSS-Ausführungen führt. Diese Kombination reduziert die Bearbeitungszeit und schont Maschine sowie Werkstück, sodass Werkstätten und Fertigungsbereiche produktiver arbeiten. Präzise Ergebnisse durch Normkonformität und Geometrie Die Auslegung nach DIN 338 und die Typ-N Spiralform machen den Bohrer besonders geeignet für Metallarbeiten auf Handbohrmaschinen und stationären Maschinen. Der 135° Spitzenwinkel reduziert das Auslaufen beim Anbohren in harten Werkstoffen wie Edelstahl und Temperguss und ermöglicht eine bessere Anlaufruhe. Dadurch entstehen saubere Bohrbilder mit hoher Maßhaltigkeit, was in Montage und Serienfertigung die Nacharbeit minimiert. Geeignet für vielfältige Metallanwendungen und kurze Spannwege Die kurze Ausführung verkürzt die Überstandslänge und erhöht die Steifigkeit, was Vibrationen und Verbiegen verhindert. Typische Einsatzgebiete sind legierter und unlegierter Stahl, Gussstahl, Gusseisen, Sintereisen, Temperguss, Nichteisenmetalle und Hartkunststoffe. Durch die robuste Bauweise lässt sich der Bohrer sowohl in Handbohrmaschinen als auch in stationären Bohrmaschinen einsetzen, wenn Stabilität und präzise Führung gefragt sind. Anwendungshinweise für sicheren und wirtschaftlichen Einsatz Für Durchmesser im Bereich von 2,0 mm bis 13,0 mm ist direktes Bohren meist möglich; bei besonders hohen Präzisionsanforderungen empfiehlt sich vorheriges Zentrieren oder Vorbohren, um die Querschneide zu entlasten. Bei harten Werkstoffen und längeren Bohrungen Kühlmittel verwenden und moderate Drehzahlen wählen, um Standzeit und Ergebnis zu optimieren. Der geschliffene Zylinderschaft erfordert sorgfältige Handhabung, bietet aber den Vorteil hoher Rundlaufgenauigkeit und exakter Bohrbilder. Für präzise Metallbearbeitung empfiehlt MetavCUT diesen Spiralbohrer; bei technischen Fragen oder Unsicherheiten berät METAV Werkzeuge gern persönlich per eMail info@metav-werkzeuge.com, Telefon +49 2822 7131930 oder WhatsApp +49 170 2837271 Bezeichnung: Spiralbohrer Marke: MetavCUT SKU: 45065-FDA Durchmesser: 6,5 mm Spitzenwinkel: 135° Typ: Typ N (Normalspirale) Material: HSS-G Ausführung: kurz Schaft Ausführung: geschliffen Spirallänge: 63 mm Gesamtlänge: 101 mm Farbe: blank Norm: DIN 338 Modellserie: Standard Line Für Bohrmaschine: Handbohrmaschine Anwendung: Bohrer für Metall Verpackungseinheit: 10 Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ Ist der Spiralbohrer 6,5 mm von MetavCUT für Handbohrmaschinen geeignet? Der Spiralbohrer 6,5 mm von MetavCUT ist für Handbohrmaschinen und stationäre Maschinen geeignet; im Bereich 2,0 mm bis 13,0 mm sind Handgeräte üblich, sinnvoll ist bei hoher Präzision vorheriges Zentrieren. Für welche Materialien ist der MetavCUT Spiralbohrer gedacht? Der MetavCUT Spiralbohrer in HSS-G eignet sich für legierten und unlegierten Stahl, Gussstahl, Gusseisen, Sintereisen, Temperguss, Nichteisenmetalle und Hartkunststoff. Warum ist der 135° Spitzenwinkel beim Spiralbohrer von MetavCUT wichtig? Der 135° Spitzenwinkel des MetavCUT Spiralbohrers reduziert das Auslaufen beim Anbohren harter Werkstoffe und sorgt für ruhigeren Anlauf sowie saubere Bohrbilder. Brauche ich Kühlung beim Einsatz des Spiralbohrers von MetavCUT? Bei Hartmaterialien oder längeren Bohrungen wird für den MetavCUT Spiralbohrer die Verwendung von Kühlschmierstoff empfohlen, um Standzeit und Oberflächenqualität zu verbessern und Überhitzung zu vermeiden. {"@context":"https://schema.org","@graph":[{"@type":"Product","@id":"#45065-FDA","sku":"45065-FDA","mpn":"45065-FDA","name":"Spiralbohrer 45065-FDA","description":"Spiralbohrer 6,5 mm, kurze Ausführung, Typ N, HSS-G, 135° Spitzenwinkel, geschliffener Zylinderschaft nach DIN 338; entwickelt für präzise Metallbohrungen in legierten und unlegierten Stählen sowie Gusswerkstoffen; hohe Stabilität durch kurze Auskraglänge und verbesserter Spanabtransport","image":["https://files.plytix.com/api/v1.1/file/public_files/pim/assets/57/c3/98/62/6298c3575d155f1bc7e497fd/images/8e/48/c5/69/69c5488eb2b3400ba580741c/logo-metav-1200-675.png","https://files.plytix.com/api/v1.1/file/public_files/pim/assets/57/c3/98/62/6298c3575d155f1bc7e497fd/images/8e/48/c5/69/69c5488eb2b3400ba580741b/logo-metav-1200-1200.png","https://files.plytix.com/api/v1.1/file/public_files/pim/assets/57/c3/98/62/6298c3575d155f1bc7e497fd/images/8e/48/c5/69/69c5488eb2b3400ba580741e/logo-metav-1200-900.png"],"additionalProperty":[{"@type":"PropertyValue","name":"Bezeichnung","value":"Spiralbohrer"},{"@type":"PropertyValue","name":"Durchmesser","value":"6,5 mm"},{"@type":"PropertyValue","name":"Spitzenwinkel","value":"135°"},{"@type":"PropertyValue","name":"Typ","value":"Typ N"},{"@type":"PropertyValue","name":"Material","value":"HSS-G"},{"@type":"PropertyValue","name":"Ausführung","value":"kurz"},{"@type":"PropertyValue","name":"Schaft Ausführung","value":"geschliffen"},{"@type":"PropertyValue","name":"Spirallänge","value":"63 mm"},{"@type":"PropertyValue","name":"Gesamtlänge","value":"101 mm"},{"@type":"PropertyValue","name":"Farbe","value":"blank"},{"@type":"PropertyValue","name":"Norm","value":"DIN 338"},{"@type":"PropertyValue","name":"Modellserie","value":"Standard Line"},{"@type":"PropertyValue","name":"Für Bohrmaschine","value":"Handbohrmaschine"},{"@type":"PropertyValue","name":"Anwendung","value":"Bohrer für Metall"},{"@type":"PropertyValue","name":"Verpackungseinheit","value":"10"}]},{"@type":"FAQPage","mainEntity":[{"@type":"Question","name":"Ist der Spiralbohrer 6,5 mm von MetavCUT für Handbohrmaschinen geeignet?","acceptedAnswer":{"@type":"Answer","text":"Der Spiralbohrer 6,5 mm von MetavCUT ist für Handbohrmaschinen und stationäre Maschinen geeignet; im Bereich 2,0 mm bis 13,0 mm ist direktes Bohren möglich, bei hoher Präzision empfiehlt sich vorheriges Zentrieren."}},{"@type":"Question","name":"Für welche Materialien ist der MetavCUT Spiralbohrer gedacht?","acceptedAnswer":{"@type":"Answer","text":"Der MetavCUT Spiralbohrer in HSS-G eignet sich für legierten und unlegierten Stahl, Gussstahl, Gusseisen, Sintereisen, Temperguss, Nichteisenmetalle und Hartkunststoff."}},{"@type":"Question","name":"Warum ist der 135° Spitzenwinkel beim Spiralbohrer von MetavCUT wichtig?","acceptedAnswer":{"@type":"Answer","text":"Der 135° Spitzenwinkel des MetavCUT Spiralbohrers reduziert das Auslaufen beim Anbohren harter Werkstoffe und sorgt für ruhigeren Anlauf sowie saubere Bohrbilder."}},{"@type":"Question","name":"Brauche ich Kühlung beim Einsatz des Spiralbohrers von MetavCUT?","acceptedAnswer":{"@type":"Answer","text":"Bei Hartmaterialien oder längeren Bohrungen wird für den MetavCUT Spiralbohrer die Verwendung von Kühlschmierstoff empfohlen, um Standzeit und Oberflächenqualität zu verbessern und Überhitzung zu vermeiden."}}]},{"@type":"ItemPage","url":"https://metav-shop.de/product/45065-FDA","dateModified":"2026-05-04T12:00:00+01:00","author":{"@type":"Person","name":"Stephan Bayer","url":"https://www.linkedin.com/in/stephan-bayer/"},"publisher":{"@type":"Organization","name":"Metav Werkzeuge GmbH","url":"https://metav-shop.de","logo":{"@type":"ImageObject","url":"https://files.plytix.com/api/v1.1/file/public_files/pim/assets/57/c3/98/62/6298c3575d155f1bc7e497fd/images/8e/48/c5/69/69c5488eb2b3400ba580741c/logo-metav-1200-675.png","width":1200,"height":675},"address":{"@type":"PostalAddress","streetAddress":"Parkring 45","postalCode":"46446","addressLocality":"Emmerich","addressCountry":"DE"},"telephone":"+49 2822 7131930","email":"info@metav-werkzeuge.com"},"about":[{"@type":"Thing","name":"Spiralbohrer Serie: Standard Line"},{"@type":"Thing","name":"Kurze Ausführung nach DIN 338"},{"@type":"Thing","name":"HSS-G geschliffen für Metallanwendungen"}],"mentions":[{"@type":"Thing","name":"Einsatz in Handbohrmaschine empfohlen"},{"@type":"Thing","name":"Geeignet für legierten und unlegierten Stahl"},{"@type":"Thing","name":"Empfehlung: Kühlschmierstoff bei harten Werkstoffen"}]}]}

Twist Drill — Short HSS‑G Metal Drill, 6.5 mm, 135° (Type N, DIN 338, Bright Finished) The Twist Drill is a short HSS‑G drill for Drilling Machines, designed for precise metal drilling and heavy‑duty applications. Short HSS‑G design for demanding metal work Higher stability from reduced overhang and short length 135° tip for efficient entry in hard materials Fully ground shank for high concentricity DIN 338 compliant short twist drill Faster, more stable drilling for metal workpieces The Short Design of this HSS‑G Twist Drill reduces the protruding length from the Chuck, delivering noticeably higher Stability and reduced deflection when drilling into hard alloys. This stability directly improves hole accuracy and roundness, which is essential in workshop and industrial settings where repeatable results matter. Users benefit from lower scrap rates and less rework when tight tolerances are required. Lower feed force and improved penetration in hard materials A 135° Tip Angle combined with the ground geometry allows easier entry into harder materials such as stainless steel. The ground HSS-G geometry reduces the required feed force by up to 50% and can enable up to 40% faster drilling compared with conventional HSS variants. For applications that demand efficient material removal and less operator fatigue, this short Twist Drill offers measurable productivity gains. Precisely ground flute geometry for clean holes The fully ground flutes (HSS‑G) produce sharp cutting edges and excellent concentricity, resulting in clean, burr‑reduced holes and improved surface finish. This benefit is particularly useful when subsequent operations—such as reaming or tapping—rely on a high‑quality pilot hole. Note that ground drills can be more brittle than rolled types, so cooling and steady clamping are recommended for best tool life. Optimised for metal; simple explanation for non‑specialists Type N represents a classic metal Twist Drill spiral, intended for Metal Drilling rather than soft wood or masonry. In practical terms: choose this short HSS‑G drill when working on alloyed or unalloyed steel, cast steel, cast iron, sintered iron, non‑ferrous metals and hard plastics. If drilling in wood or concrete, a different specialist drill type will deliver better guidance and hole quality. Robust standard compliance and practical handling tips Conforming to DIN 338 confirms that this short Twist Drill meets established industry dimensions and shank specifications, simplifying machine setup and toolholder selection. For consistent results: use appropriate coolant, clamp the workpiece securely, and avoid excessive overhang—even though the short length improves rigidity, correct machining practice remains decisive for tool life. Strongly recommended: choose the MetavCUT short HSS‑G Twist Drill for stable, precise metal drilling; for application advice or detailed technical data contact METAV Werkzeuge — expert consultation available by email, phone or WhatsApp at info@metav-werkzeuge.com / +49 2822 7131930 / +49 170 2837271 Technical data Designation: Twist Drill (Short) Brand: MetavCUT SKU: 48065-FDA Diameter: 6.5 mm Tip angle: 135° Type: Type N (Normal Spiral) Execution: Short Overall length: 101 mm Spiral length: 63 mm Shank execution: Fully Ground Material: HSS‑G (Ground High Speed Steel) Surface / Colour: Bright Finished For Drilling Machine: Drilling Machine (Hand Drill compatibility for small tasks) Norm: DIN 338 Application: Drills for Metal Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What is the short Twist Drill best used for? The short Twist Drill from MetavCUT is primarily used for Metal Drilling; its reduced overhang and HSS‑G geometry make it suitable for precise work in alloyed and unalloyed steel, cast components and hard plastics where accuracy and low deflection are required. How does the 135° tip affect drilling performance? A 135° tip on the MetavCUT Twist Drill provides a flatter cutting face that shortens penetration time in harder materials and improves centring for tough steels, making the tool more efficient for industrial metalworking tasks. What are Twist Drills used for Twist Drills are mainly applied when machining high‑strength materials and larger drill diameters. This form is easy to regrind and withstands higher loads, making it suitable for demanding metal cutting work. Which three drill types exist There are three common drill categories: Metal Drills, Wood Drills, Stone/Concrete Drills. Why are Twist Drills sharpened (pointed)? Sharpening the point reduces the cross‑cut at the tip, which significantly lowers friction and the required feed force. At the same time the sharpened point improves centring in the workpiece. Can you use a metal drill in wood? A Metal Drill can be used in Wood, but guidance and finish are inferior compared with dedicated wood bits. Metal Drills are easier to resharpen and have less self‑feeding tendency, resulting in a rougher hole in timber. For which drilling depths is the Twist Drill most used? A solid through hole is typically made with a Twist Drill. For diameters up to 20 mm and drill depths up to 100 mm, the Twist Drill is the most commonly used tool. Is HSS or HSSE better? The general belief that HSSE is always superior to HSS is not universally correct. Evaluate operating conditions carefully to decide whether the higher purchase cost of HSSE is justified for the intended application. If uncertain whether this MetavCUT Twist Drill meets specific requirements or for supplementary technical data, METAV Werkzeuge provides comprehensive and competent advice — contact info@metav-werkzeuge.com, phone +49 2822 7131930 or WhatsApp +49 170 2837271.

Twist Drill (Short, 6.5 mm) — HSS‑G, TIN‑coated, DIN 338 by MetavCUT, 118° point angle, fully ground shank A Twist Drill short HSS‑G bit designed for precise metal drilling in Drilling Machines, offering a TIN‑coating for reduced wear and conformity to DIN 338. Short design for increased stability TIN‑coated for reduced friction and wear HSS‑G material for high cutting speed 118° point angle for improved centring Conforms to DIN 338 for metalworking Greater accuracy through a short design and premium HSS‑G This short twist drill from MetavCUT combines a compact overall length with a fully ground HSS‑G body to deliver higher rigidity and precise hole quality. Because the outboard length is reduced, the bit shows less deflection under load, which directly benefits hole concentricity and dimensional accuracy when working with steel and other metals. The ground manufacturing process produces very sharp cutting edges and excellent runout accuracy, resulting in cleaner holes and reduced rework. Longer tool life and lower wear thanks to TIN coating A TIN‑coated surface significantly lowers friction at the cutting edges and helps dissipate heat when used with an appropriate coolant. This coating increases lifetime in metal applications and reduces adhesive wear, so the bit maintains geometry longer under continuous operation. For users who prioritise uptime and fewer tool changes, the TIN layer offers a measurable advantage during serial drilling tasks on alloyed and unalloyed steels, cast materials and non‑ferrous metals. Standards and production method ensure repeatable results Manufactured to DIN 338 as a short twist drill, this bit follows established dimensional and geometric specifications for cylindrical shank short drills. The designation HSS‑G (ground) indicates that the flutes and point geometry are produced by CNC grinding rather than rolling, which yields very sharp cutting lips and high concentricity. For operators this means reliably reproducible hole quality in stationary and portable drilling setups, provided cooling and correct feeds are applied. Application range and practical guidance for use Designed primarily as a Twist Drill for metal, the short HSS‑G geometry is suitable for alloyed and unalloyed steel, temper cast iron, cast iron, sintered iron, copper, bronze, nickel silver and hard plastics. The 118° point angle aids initial centring and is particularly helpful when working on slightly curved or softer surfaces such as aluminium, though feed and speed must be adapted per material. When drilling harder steels or deep holes consider appropriate cooling and gradual pecking to maintain tool life and hole quality. MetavCUT recommends this short Twist Drill for precision metalworking tasks; METAV Werkzeuge provides expert technical advice and application support — contact info@metav-werkzeuge.com, phone +49 2822 7131930 or WhatsApp +49 170 2837271 for personalised assistance Technical Information Designation: Twist Drill (Short) Brand: MetavCUT SKU: 28065-FDA Diameter: 6.5 mm Point angle: 118° Type / Execution: short Coating / Colour: TIN‑coated Application: Drills for metal Spiral length: 63 mm Overall length: 101 mm Shank finish: fully ground Material: HSS‑G Norm: DIN 338 Series: Basic Line Suitable for: alloyed and unalloyed steel, temper cast iron, cast iron, sintered iron, copper, bronze, nickel silver, hard plastics Manufacturer: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What is a Twist Drill used for and which materials suit it best? The MetavCUT Twist Drill is primarily used for metalworking and is suitable for alloyed and unalloyed steel, cast iron, copper, bronze and hard plastics; its short design gives better stability for precise metal drilling operations. Why choose a TIN‑coated HSS‑G MetavCUT Twist Drill? A TIN‑coated HSS‑G MetavCUT Twist Drill reduces friction at the cutting edge, increases resistance to adhesive wear and therefore extends service life when drilling metals under appropriate cooling. For what are Twist Drills mainly applied? They are mainly applied in the machining of high‑strength materials and for larger drill diameters; the shape is relatively simple to grind and withstands higher loads. Which three drill types are there? The three common drill types are metal drills, wood drills and stone/concrete drills. Why are Twist Drills re‑pointed? Re‑pointing reduces the transverse cutting edge at the tip of a Twist Drill, lowering friction forces so less thrust is needed while improving the drill’s centring in the workpiece. Can a metal drill be used for wood? A metal drill can be used in wood but offers worse guidance and a less clean finish; however, such drill bits are easier to regrind and usually have a lower self‑feeding tendency. At which drilling depths is the Twist Drill the most used tool? For solid hole drilling, a Twist Drill is commonly used in diameters up to 20 mm and depths up to 100 mm; it is the most frequently applied tool for these ranges.

Twist Drill Type N by MetavCUT — 6.5 mm, 135° TIN-coated, short HSS-G (DIN 338) The Twist Drill Type N short HSS-G is a precision metalworking tool designed for use in Drilling Machines, offering high stability and extended tool life for demanding industrial applications. Short design for increased stability TIN-coated surface extends tool life 135° tip for hard materials like stainless steel HSS-G fully ground for fast, precise drilling Conforms to DIN 338 for reliable metalworking Increased Stability and Accurate Holes for Metalworking Shorter tool overhang improves performance in demanding tasks. The short design of this Twist Drill minimises vibration and lateral deflection, delivering consistently accurate holes in alloys and steels. Because the flutes and cutting geometry are ground rather than rolled, the tool achieves high runout precision and cleaner bore edges, which reduces rework and improves component fit. This stability is especially beneficial when machining on portable and stationary Drilling Machines where rigid setup and repeatable hole quality are required. Coating and Material for Longer Lifetime and Efficiency A TIN-coated surface combined with HSS-G base material reduces friction and increases wear resistance during metal drilling. The coating lowers heat generation at the cutting edge, so the tool maintains hardness and cutting performance for longer periods under appropriate cooling. For operations involving alloyed and unalloyed steel, cast materials or non-ferrous metals, this combination supports higher productivity and fewer tool changes, which contributes directly to process efficiency on the shopfloor. Geometry Optimised for Hard Materials and Reduced Feed Forces The 135° tip angle is tailored for harder workpieces and reduces initial biting forces. A blunter tip compared with standard angles decreases tendency to wander on the workpiece surface and shortens lead-in time when penetrating dense materials. The ground geometry also ensures sharper cutting edges and improved chip evacuation, meaning that operators can achieve deeper, cleaner holes with less applied pressure—important when machining tough steels or sintered components. Practical Use Cases and Machine Compatibility Designed in accordance with DIN 338, this short Type N drill is suited for metalworking tasks on both stationary and mobile Drilling Machines. The fully ground shank facilitates precise clamping and concentricity in standard chucks. Typical applications include machining of Tempered Steel, Gusseisen, Bronze, Copper and engineering plastics where controlled chip formation and tool life are priorities. For best results, pairing the tool with appropriate coolant and stable fixturing is recommended to maximise performance and avoid premature wear. Who Benefits from This Tool and Why Manufacturers, toolrooms and maintenance professionals who require reproducible hole quality under production conditions will find the Twist Drill advantageous. Its short format makes it ideal for setups where rigidity is limited or where series precision is essential. For users transitioning from rolled HSS drills, the ground geometry delivers noticeable improvements in drilling speed and surface finish while remaining simple to resharpen when required. We recommend MetavCUT’s short TIN-coated HSS-G Twist Drill for precision metalworking applications; for expert technical advice or to verify suitability for specific materials and machine setups, METAV Werkzeuge provides extensive consultation via email at info@metav-werkzeuge.com, by phone at +49 2822 7131930 or WhatsApp at +49 170 2837271 Technical Data Designation: Twist Drill (Spiralbohrer) Brand/Manufacturer: MetavCUT SKU: 46065-FDA Diameter: 6.5 mm Tip angle: 135° Type: Type N Coating: TIN-coated Material: HSS-G Spiral length: 63 mm Overall length: 101 mm Shank execution: Fully ground Execution: Short Standard: DIN 338 Intended machine: Drilling Machine Application: Drills for metal Model series: Standard Line Colour: TIN-coated Manufacturer: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What is a Twist Drill primarily used for? A MetavCUT Twist Drill Type N is primarily used for machining high-strength materials and larger drill diameters; it is particularly effective when working in metal because the short design and ground geometry offer higher precision. This form is easy to resharpen and withstands higher loads, making it suitable for professional metalworking tasks. Which three drill types exist? The main categories are Metal Drills, Wood Drills and Masonry/Concrete Drills; the MetavCUT Twist Drill belongs to the Metal Drills group and is optimised for metal applications with corresponding geometry and coatings.

Twist Drill — Short Type N, 6.5 mm, TIN-coated HSS-G (MetavCUT) The Twist Drill short Type N is a precision metal-drilling bit for hand and drilling machines, engineered for stable, accurate holes in hard materials. Short design for high stability and precision 6.5 mm Diameter for standard metal holes 135° Point angle for harder materials TIN-coated HSS-G for extended tool life Fully ground shank for fast, clean drilling High stability and longer tool life for demanding metalwork Short-design Twist Drill bits combine a reduced overhang with superior rigidity, which minimizes vibration and deflection during drilling. The HSS-G substrate paired with a TIN-coated surface significantly lowers friction and wear; with appropriate cooling the coating helps to extend lifetime when machining alloyed and unalloyed steel, cast parts, copper alloys and hard plastics. This results in more consistent Hole Quality and fewer tool changes for production and workshop tasks. Geometry optimised for hard materials and fast centring A 135° point angle reduces walking and shortens the initial penetration time when tackling stainless steels and other tough metals. The fully ground flute geometry (HSS-G) produces sharp cutting edges and high runout accuracy, giving cleaner chips and improved centring compared with rolled drills. Classified as Type N and conforming to DIN 338, this design is the classic choice for metalworking where repeatable, precise results are required. Efficient performance with lower feed forces and robust construction The shortened overall length and fully ground shaft reduce the required thrust and improve stability under load; tests of comparable ground HSS tools show up to 40% faster drilling and about 50% less feed force, which benefits battery-powered and portable drilling machines as well as stationary equipment. The combination of short geometry and the TIN-coated surface makes this bit particularly suitable for workshop applications where throughput and hole integrity matter. Who benefits from this short metal drill bit and how to use it best Workshops, maintenance teams and precision fabricators will appreciate the MetavCUT short Twist Drill when consistent hole diameter and surface finish are priorities. Use moderate spindle speeds, steady feed, and an appropriate coolant for alloyed steels to maximise the advantage of the coating and ground cutting edges. The bit is matched to hand and drilling machines and is recommended for metal drilling tasks up to typical diameters and depths encountered in mechanical assembly and repair. Strong recommendation: For precision metalworking choose the MetavCUT Twist Drill short Type N with TIN coating — METAV Werkzeuge offers expert, personalised advice if you are unsure whether this tool suits your application; contact us by eMail: info@metav-werkzeuge.com ☎️ +49 2822 7131930 ✔️ WhatsApp +49 170 2837271 Designation: Twist Drill Brand: MetavCUT SKU: 41065-FDA Diameter: 6.5 mm Point angle: 135° Type: Type N Execution: short Material: HSS-G Coating/Colour: TIN-coated Shank execution: fully ground Flute length (Spirallänge): 63 mm Overall length (Gesamtlänge): 101 mm For drilling machine: Drilling Machine / Handbohrmaschine Norm: DIN 338 Model series: Profi Line Application: Drills for metal Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What is a Twist Drill used for and which materials suit it best? The MetavCUT Twist Drill (Type N) is primarily used for machining high-strength materials and larger diameters; its short design is especially suitable for precise metalworking. It performs well on alloyed and unalloyed steel, cast iron, copper alloys and hard plastics. The geometry is easy to resharpen and withstands higher loads under proper cooling. Which three drill types are there? Typical categories are metal drills, wood drills and stone/concrete drills. The MetavCUT Twist Drill belongs to the metal drill group (Type N), optimised for metal applications rather than soft wood or masonry. Why are Twist Drills point-ground? Point grinding reduces the cross-edge at the tip of the Twist Drill, lowering friction and therefore reducing the required feed force. At the same time the ground tip improves centring in the workpiece for more accurate hole starts. Can the Twist Drill be used to drill wood? A metal Twist Drill can be used in wood, but guidance and hole finish are inferior compared with dedicated wood drills. The MetavCUT short metal drill is easier to resharpen and offers less self-feeding effect, so results in wood are possible but not optimal.

Twist Drill Spezial — HSS‑G Metal Twist Drill, Ø 6.5 mm, 135° The Twist Drill Spezial is a HSS‑G metal twist drill designed for high‑speed drilling in alloyed and unalloyed steels and suitable for drilling machines and cordless hand drills. High‑performance HSS‑G for metalworking 135° point angle for harder materials Multi‑bevel W tip for clean hole entry Triangular shank ensures secure grip in chucks Conforms to DIN 338 for short HSS twist drills Maximise drilling speed with reduced feed effort The Twist Drill Spezial combines a ground HSS‑G body with an optimised cutting geometry that delivers up to 40% faster drilling while requiring 50% less feed force compared with conventional HSS drills. This efficiency reduces operator fatigue on repetitive tasks and shortens cycle times in production. The specially designed tip supports quick penetration and stable cutting under higher loads, making it well suited for industrial metalworking applications. Precise design for cleaner holes and reliable clamping The multi‑bevel W tip and tailored flute geometry enable a clean start and produce holes with minimal burr formation. The drill’s triangular shank provides positive drive in standard chucks and quick‑change adapters, improving torque transmission for cordless and handheld use. The product follows DIN 338, a recognised standard for short spiral drills with cylindrical shank, which helps ensure reproducible dimensions and compatibility with machine tool holders. Robust material choice and target applications Manufactured from HSS‑G, this twist drill is optimised for drilling in alloyed and unalloyed Steel, Cast Iron, Aluminium, Non‑ferrous Metals and Hard Plastics. The 135° point angle reduces wandering on harder materials such as stainless steel and decreases required thrust, which supports cleaner, more accurate holes in demanding tasks. Typical users include workshop professionals, maintenance technicians and production operatives who require consistent results on metallic components. Practical handling, resharpening and working tips A larger point angle such as 135° lowers the quenching of the tip and shortens the initial entry time; it also improves centring when reaming is not desired. The W‑sharpened tip is relatively easy to resharpen on standard bench grinders without losing geometry, extending tool life and reducing consumable costs. For complex material mixes or special production conditions, METAV Werkzeuge provides expert technical advice and support to select the correct drill geometry and cutting parameters. Strong recommendation: Choose the MetavCUT Twist Drill Spezial for demanding metal drilling tasks — for tailored advice contact METAV Werkzeuge: info@metav-werkzeuge.com · Tel +49 2822 7131930 · WhatsApp +49 170 2837271 Technical specifications Designation: Twist Drill Brand: MetavCUT SKU: 55065-FDA Type / Model series: Spezial Diameter: 6.5 mm Spiral length: 63 mm Overall length: 101 mm Point angle: 135° Material: HSS‑G Shank execution: with multi‑bevel cutting edge and triangular shank Application: Drills for metal For: Drilling Machine / Hand drill Norm: DIN 338 Manufacturer: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What is a Twist Drill used for and which materials suit the MetavCUT Twist Drill Spezial? The MetavCUT Twist Drill Spezial is primarily used for machining high‑strength materials and larger hole diameters; it is effective in alloyed and unalloyed Steel, Cast Iron, Non‑ferrous Metals, Aluminium and Hard Plastics. Its sharpened HSS‑G geometry allows faster drilling and lower feed forces while maintaining precise, burr‑reduced hole edges. Which three drill types exist? Three common drill types are metal drills, wood drills and stone/concrete drills; the MetavCUT Twist Drill Spezial belongs to the metal drill category and is engineered specifically for metalworking tasks.

Spiralbohrer HSS‑G 6,5 mm, 135°, geschliffen, lang, DIN 340, blank (MetavCUT) Der Spiralbohrer HSS‑G 6,5 mm ist ein langer Metallbohrer für tiefe und schwer zugängliche Bohrungen in Stahl, Guss und Nichteisenmetallen. HSS‑G geschliffen für präzise Metallbohrungen 6,5 mm Durchmesser für Standard‑Anwendungen 135° Spitzenwinkel für harte Werkstoffe Lange Ausführung DIN 340 für tiefe Löcher Spirallänge 97 mm, Gesamtlänge 148 mm Schnelleres Bohren mit weniger Kraftaufwand für effiziente Werkstattarbeit Der geschliffene HSS‑G‑Bohrer bietet spürbare Arbeitserleichterung: bis zu 40 % schnelleres Bohren und 50 % geringere Anpresskraft gegenüber konventionellen HSS‑Ausführungen. Das Ergebnis sind saubere, runde Bohrlöcher mit hoher Rundlaufgenauigkeit, insbesondere bei Arbeiten in legiertem und unlegiertem Stahl sowie Grauguss. Dieser Vorteil reduziert Ermüdung bei wiederkehrenden Arbeiten und steigert die Produktivität in der Werkstatt. Geeignet für tiefe Bohrungen und anspruchsvolle Werkstoffe Die lange Ausführung nach DIN 340 und die Spirallänge 97 mm ermöglichen das sichere Bohren tieferer Löcher ohne vorzeitiges Blockieren der Späne bei moderaten Tiefen. Der 135° Spitzenwinkel erleichtert das Anbohren in harten Werkstoffen und verkürzt die Anbohrzeit, was besonders bei legierten Stählen und Temperguss von Vorteil ist. Die geschliffene Geometrie sorgt für scharfe Schneiden und saubere Spanabfuhr. Praktische Anwendungshinweise für sichere und langlebige Nutzung Bei Einsatz mit einer Handbohrmaschine empfiehlt sich ein ruhiger, gleichmäßiger Vorschub und gegebenenfalls der Einsatz von Kühlschmierstoff, um Überhitzung zu vermeiden. Geschliffene Bohrer können spröder reagieren als gewalzte Varianten; deshalb ist die Verwendung unter stabiler Maschinenaufnahme oder mit geeigneter Kühlung sinnvoll. Für besonders präzise Passungen kann ein Anpunkten mit einem Zentrierbohrer die Positioniergenauigkeit erhöhen. Entwickelt für Handwerk, Industrie und ambitionierte Heimwerker Der MetavCUT Standard Line richtet sich an Anwender, die einen zuverlässigen, leistungsfähigen Spiralbohrer für Metall benötigen. Ob Instandsetzung, Maschinenbau oder anspruchsvolle Werkstattprojekte: Die Kombination aus Materialwahl HSS‑G, geschliffener Schaftausführung und langer Bauform macht diesen Bohrer zur praktischen Wahl für tiefe und saubere Bohrungen. Empfehlung: Den MetavCUT Spiralbohrer HSS‑G für präzise Tiefbohrungen einsetzen und bei Fragen die fachkundige Beratung von METAV Werkzeuge per E‑Mail info@metav-werkzeuge.com oder Telefon +49 2822 7131930 nutzen Bezeichnung: Spiralbohrer Marke: MetavCUT SKU: 53065-FDA Modellserie: Standard Line Material: HSS‑G Durchmesser: 6,5 mm Spitzenwinkel: 135° Norm: DIN 340 Ausführung: lang Schaft Ausführung: geschliffen Spirallänge: 97 mm Gesamtlänge: 148 mm Farbe: blank Für Bohrmaschine: Handbohrmaschine Verpackungseinheit: 10 Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ Ist der MetavCUT Spiralbohrer HSS‑G 6,5 mm für Edelstahl geeignet? Der Spiralbohrer HSS‑G von MetavCUT mit 135° Spitzenwinkel eignet sich für härtere Werkstoffe; bei Edelstahl sollten langsame Schnittgeschwindigkeiten und Kühlschmierstoff verwendet werden, um Wärme und Verschleiß zu reduzieren. Kann ich den Spiralbohrer HSS‑G 6,5 mm in einer Handbohrmaschine verwenden? Ja, der Spiralbohrer MetavCUT Standard Line ist für die Nutzung mit einer Handbohrmaschine vorgesehen, wobei ein gleichmäßiger Vorschub und stabile Aufnahme die Lebensdauer verlängern. Wie tief kann ich mit dem Spiralbohrer HSS‑G 6,5 mm ohne Vorbohren arbeiten? Der lange Spiralbohrer ist für tiefere Bohrungen geeignet; bei sehr tiefen oder präzisen Bohrungen empfiehlt MetavCUT, stufenweise vorzugehen oder das Werkstück zu kühlen und Späne regelmässig zu entfernen. Was sind typische Materialien, in die der Spiralbohrer HSS‑G 6,5 mm problemlos bohrt? Der Spiralbohrer MetavCUT HSS‑G ist ausgelegt für legierte und unlegierte Stähle, Temperguss, Grauguss, Sphäroguss, Sintereisen sowie Nichteisenmetalle und Hartkunststoffe; für sehr zähe oder gehärtete Stähle sind Spezialwerkzeuge zu prüfen. Sind Sie sich nicht sicher, ob dieses Werkzeug Ihre Anforderungen erfüllt? Oder benötigen Sie ergänzende technische Daten? Kein Problem – wir stehen Ihnen gerne zur Verfügung. 📧 info@metav-werkzeuge.com ☎️ +49 2822 7131930 ✔️ WhatsApp +49 170 2837271 {"@context":"https://schema.org","@graph":[{"@type":"Product","@id":"#53065-FDA","sku":"53065-FDA","mpn":"53065-FDA","name":"Spiralbohrer 6,5 mm HSS-G lang DIN 340","description":"Spiralbohrer HSS‑G 6,5 mm, geschliffen, Spitzenwinkel 135°, lange Ausführung nach DIN 340, Spirallänge 97 mm, Gesamtlänge 148 mm; geeignet für tiefe Metallbohrungen in legierten und unlegierten Stählen, Guss und Nichteisenmetallen; hohe Rundlaufgenauigkeit und saubere Spanabfuhr.","image":["https://files.plytix.com/api/v1.1/file/public_files/pim/assets/57/c3/98/62/6298c3575d155f1bc7e497fd/images/8e/48/c5/69/69c5488eb2b3400ba580741b/logo-metav-1200-1200.png","https://files.plytix.com/api/v1.1/file/public_files/pim/assets/57/c3/98/62/6298c3575d155f1bc7e497fd/images/8e/48/c5/69/69c5488eb2b3400ba580741e/logo-metav-1200-900.png","https://files.plytix.com/api/v1.1/file/public_files/pim/assets/57/c3/98/62/6298c3575d155f1bc7e497fd/images/8e/48/c5/69/69c5488eb2b3400ba580741c/logo-metav-1200-675.png"],"additionalProperty":[{"@type":"PropertyValue","name":"Bezeichnung","value":"Spiralbohrer"},{"@type":"PropertyValue","name":"Marke","value":"MetavCUT"},{"@type":"PropertyValue","name":"SKU","value":"53065-FDA"},{"@type":"PropertyValue","name":"Modellserie","value":"Standard Line"},{"@type":"PropertyValue","name":"Material","value":"HSS‑G"},{"@type":"PropertyValue","name":"Durchmesser","value":"6,5 mm"},{"@type":"PropertyValue","name":"Spitzenwinkel","value":"135°"},{"@type":"PropertyValue","name":"Norm","value":"DIN 340"},{"@type":"PropertyValue","name":"Ausführung","value":"lang"},{"@type":"PropertyValue","name":"Schaft Ausführung","value":"geschliffen"},{"@type":"PropertyValue","name":"Spirallänge","value":"97 mm"},{"@type":"PropertyValue","name":"Gesamtlänge","value":"148 mm"},{"@type":"PropertyValue","name":"Farbe","value":"blank"},{"@type":"PropertyValue","name":"Für Bohrmaschine","value":"Handbohrmaschine"},{"@type":"PropertyValue","name":"Verpackungseinheit","value":"10"},{"@type":"PropertyValue","name":"Hersteller","value":"Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com"}]},{"@type":"FAQPage","mainEntity":[{"@type":"Question","name":"Ist der MetavCUT Spiralbohrer HSS‑G 6,5 mm für Edelstahl geeignet?","acceptedAnswer":{"@type":"Answer","text":"Der MetavCUT Spiralbohrer HSS‑G 6,5 mm mit 135° Spitzenwinkel eignet sich für härtere Werkstoffe; bei Edelstahl sollten langsame Schnittgeschwindigkeiten und Kühlschmierstoff verwendet werden, um Wärme und Verschleiß zu reduzieren."}},{"@type":"Question","name":"Kann ich den MetavCUT Spiralbohrer HSS‑G 6,5 mm in einer Handbohrmaschine verwenden?","acceptedAnswer":{"@type":"Answer","text":"Ja, der MetavCUT Spiralbohrer HSS‑G 6,5 mm ist für die Nutzung mit einer Handbohrmaschine vorgesehen; ein gleichmäßiger Vorschub und stabile Aufnahme verlängern die Lebensdauer."}},{"@type":"Question","name":"Wie tief kann mit dem MetavCUT Spiralbohrer HSS‑G 6,5 mm ohne Vorbohren gearbeitet werden?","acceptedAnswer":{"@type":"Answer","text":"Der lange MetavCUT Spiralbohrer HSS‑G 6,5 mm ist für tiefere Bohrungen geeignet; bei sehr tiefen oder präzisen Bohrungen empfiehlt MetavCUT stufenweises Vorgehen, Kühlung und regelmäßiges Entfernen der Späne."}},{"@type":"Question","name":"Welche Materialien bohrt der MetavCUT Spiralbohrer HSS‑G 6,5 mm problemlos?","acceptedAnswer":{"@type":"Answer","text":"Der MetavCUT Spiralbohrer HSS‑G 6,5 mm ist ausgelegt für legierte und unlegierte Stähle, Temperguss, Grauguss, Sphäroguss, Sintereisen sowie Nichteisenmetalle und Hartkunststoffe; für sehr zähe oder gehärtete Stähle sind Spezialwerkzeuge zu prüfen."}}]},{"@type":"ItemPage","url":"https://metav-shop.de","dateModified":"2026-05-04T12:00:00+01:00","author":{"@type":"Person","name":"Stephan Bayer","url":"https://www.linkedin.com/in/stephan-bayer/"},"publisher":{"@type":"Organization","name":"Metav Werkzeuge GmbH","url":"https://metav-shop.de","logo":{"@type":"ImageObject","url":"https://files.plytix.com/api/v1.1/file/public_files/pim/assets/57/c3/98/62/6298c3575d155f1bc7e497fd/images/8e/48/c5/69/69c5488eb2b3400ba580741c/logo-metav-1200-675.png","width":1200,"height":675},"address":{"@type":"PostalAddress","streetAddress":"Parkring 45","postalCode":"46446","addressLocality":"Emmerich","addressCountry":"DE"},"telephone":"+49 2822 7131930","email":"info@metav-werkzeuge.com"},"about":[{"@type":"Thing","name":"Spiralbohrer HSS-G"},{"@type":"Thing","name":"DIN 340 lange Ausführung"},{"@type":"Thing","name":"MetavCUT Standard Line"}],"mentions":[{"@type":"Thing","name":"Geschliffene Schaftausführung"},{"@type":"Thing","name":"135° Spitzenwinkel"},{"@type":"Thing","name":"Spirallänge 97 mm"}]}]}

Twist Drill — Type N short HSS drill, Ø 6.6 mm, 118°, black, DIN 338 The Twist Drill Type N is a short High Speed Steel drill designed for precision metal drilling on Drilling Machines and handheld drills. Short design for higher stability HSS material for reliable metal drilling DIN 338 conformity for consistent quality 118° point angle for improved centring Black colour for easy identification High-performance metal drilling with consistent results The Twist Drill from MetavCUT is engineered for demanding metalworking tasks where precision and stability matter. With a diameter of 6.6 mm and a 118° point angle, this short-version Type N drill enters the material cleanly and reduces wandering on curved or slightly uneven surfaces. The roll-welded HSS construction provides elasticity and durability during standard operations, making it suitable for both unalloyed and alloyed steels as well as non-ferrous metals and selected plastics. The short length reduces deflection and supports repeatable, accurate holes in machining and maintenance work. Robust design and clear standards for safe use Built to the DIN 338 specification for short Twist Drills with cylindrical shank, this tool emphasises repeatability and tool life. The reduced overall length increases rigidity and lowers the risk of bending under load, so feeds and speeds can be applied more aggressively while maintaining hole quality. The short execution also simplifies clamping in conventional chucks and minimises runout. For operators unfamiliar with terms: HSS stands for High Speed Steel, a material balanced for hardness and toughness under typical drilling temperatures. Who benefits and where to use it This Type N short Twist Drill is intended primarily for metalworkers, maintenance technicians and workshop users who require a compact, reliable drill for everyday drilling in metal. It is particularly effective in situations where free-standing reach is limited or where high stiffness prevents chatter. Even small-scale fabrication and repair shops will appreciate the easier handling and better centring behaviour on thin or curved components. If uncertainty remains about suitability for a specific job, MetavCUT and the retailer provide expert guidance to match tooling to the application. Handling tips and safety recommendations To achieve the best results with this short Twist Drill, use appropriate cutting speeds, steady feed and suitable lubricants for the target material. Short drills are less prone to breakage, but correct clamping and alignment remain essential for hole quality. The Type N spiral geometry is optimized for metal; when drilling different materials, adjust speed and lubrication accordingly. If post-processing or reworking is required, the HSS material allows straightforward resharpening to restore tip geometry and extend service life. MetavCUT recommends this Twist Drill for precision metalworking and short-reach drilling; for further technical advice or application-specific recommendations contact METAV Werkzeuge — email info@metav-werkzeuge.com or call +49 2822 7131930, WhatsApp +49 170 2837271 Technical data Designation: Twist Drill Brand: MetavCUT Diameter: 6.6 mm Point angle: 118° Total length: 101 mm Spiral length: 63 mm Material: HSS (High Speed Steel) Type: Type N Execution: short Suitable for: Drilling Machine Application: Drills for metal Standard: DIN 338 Colour: black Manufacturer: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What are Twist Drills used for and where is the MetavCUT Type N Twist Drill suitable? The MetavCUT Twist Drill Type N is mainly used for machining higher-strength materials and for larger drilling diameters in metalworking. Its short HSS design offers good elasticity and reduced breakage risk for holes under typical workshop conditions. This form is relatively easy to resharpen and withstands higher loads, making it a dependable choice for metal fabrication and repair. Which three drill types exist and how does this Twist Drill compare? Commonly distinguished drill types are metal drills, wood drills and stone/concrete drills. The MetavCUT Twist Drill Type N belongs to the metal drill category and is optimized for steel and non-ferrous metals; it differs from wood or masonry drills in point geometry and flute design, which are tailored to the specific material properties.

Twist Drill — Type N Short, 6.6 mm, 135° Point, HSS‑E, 5% Cobalt‑Alloyed (DIN 338, Fully Ground) The bold Twist Drill Type N short is designed for precision metalworking and offers enhanced stability and wear resistance for use in drilling machines and hand drills. Short design increases stability and precision 5% Cobalt‑alloyed HSS‑E for hard materials 135° point angle for reduced chipping in steel Fully ground flutes for accurate, clean holes Conforms to DIN 338 for short twist drills Optimised strength for demanding metal applications The HSS‑E composition with 5% cobalt gives the short Twist Drill improved hot hardness and wear resistance compared with standard HSS. This makes it particularly suitable for drilling alloyed and unalloyed Steel, Cast Iron, non‑ferrous metals and engineering Plastics. The shorter overall length reduces overhang and flex, resulting in higher concentricity and a lower risk of breakage when working with tougher materials. The combination of material and compact geometry therefore supports longer tool life under higher thermal and mechanical stress. Geometry that produces cleaner, more accurate holes A 135° point angle and fully ground flute geometry ensure reliable centring and a smoother entry into harder workpieces. The CNC grinding of the flute geometry (HSS‑G style) yields sharp cutting edges and a high runout accuracy, which produces precise, burr‑reduced holes. The flute (spiral) length of 63 mm is matched to a total length of 101 mm, optimising chip evacuation while maintaining rigidity. For projects that demand clean, dimensionally accurate bores, this ground short design offers clear advantages over rolled alternatives. Best practice: machines, materials and typical uses Designed as a classic Type N Twist Drill, this short variant is intended primarily for Drilling Machines but is compatible with robust hand drills when used with appropriate clamping and coolant. It excels in general metalworking tasks such as through‑holes in structural components, toolroom operations and maintenance work where stability and repeatable hole quality matter. For stainless steels and other hard alloys, use moderate speeds, steady feed and cooling to exploit the cobalt alloy’s high temperature performance. Handling, cooling and reconditioning guidance To preserve cutting performance, apply suitable cutting fluid for metalworking and avoid excessive speed that raises temperature rapidly. The fully ground tip provides excellent initial cutting action but can be more brittle than rolled designs; controlled feed rates and steady clamping are recommended. When regrinding is required, the ground geometry allows precise resharpening, but attention must be paid to the point angle to retain the 135° profile. For stationary and production environments, recommended use is with coolant and secure fixturing to prevent chipping and extend service life. Strong recommendation: For precision metal drilling tasks choose the MetavCUT Twist Drill Type N short with 5% cobalt‑alloyed HSS‑E for superior stability and durability — for tailored advice or technical support contact METAV Werkzeuge directly via email at info@metav-werkzeuge.com, by phone at +49 2822 7131930 or WhatsApp at +49 170 2837271 Designation: Twist Drill (Short, Type N) Brand: MetavCUT SKU: 47066‑FDA Diameter: 6.6 mm Point angle: 135° Type: Type N Colour / Composition: 5% cobalt‑alloyed Execution: Short Material: HSS‑E Shaft finish: Fully ground Spiral (flute) length: 63 mm Total length: 101 mm Model series: Standard Line Standard / Norm: DIN 338 Suitable for: Drilling Machine (Hand Drill compatible with precautions) Manufacturer: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What are Twist Drills used for and when is a short Type N advantageous? The MetavCUT Twist Drill Type N short is used primarily for machining metal; its short geometry gives increased stability and is therefore advantageous for precision holes in harder materials and applications where reduced overhang prevents bending and breakage. Which three main drill types exist? Common distinctions are Metal drills, Wood drills and Stone/Concrete drills; the MetavCUT Twist Drill Type N belongs to the metal drill category and is optimised for metalworking tasks. Can the MetavCUT Twist Drill be used in a hand drill? The MetavCUT Twist Drill Type N short can be used in a robust hand drill, but optimal results are achieved with a drilling machine; secure clamping and coolant are recommended to prevent chatter and extend tool life. Why is the tip of a twist drill ground (pointed)? The ground point on the MetavCUT Twist Drill reduces the chisel edge at the tip, lowering friction and required feed forces while improving centring in the workpiece, which results in easier penetration and more accurate holes.

Spiralbohrer HSS-G 6,6 mm kurz, Typ N, 135°, geschliffener Zylinderschaft, DIN 338, blank, MetavCUT Der Spiralbohrer von MetavCUT ist ein kurzer, geschliffener HSS-G Bohrer mit 135° Spitzenwinkel, konzipiert für präzise Metallbohrungen mit Hand- oder stationärer Bohrmaschine. Kurze Ausführung für hohe Stabilität Geschliffener Zylinderschaft für präzise Läufe Spitzenwinkel 135° für harte Werkstoffe Normgerechte Fertigung nach DIN 338 Effizienteres Bohren dank optimierter Geometrie Hohe Schnittgeschwindigkeit und Materialeigenschaften für effizientes Arbeiten Der kurze Spiralbohrer aus HSS-G bietet eine deutlich höhere Schnittgeschwindigkeit im Vergleich zu herkömmlichen HSS-Werkzeugen. Durch die optimierte Geometrie reduziert sich die erforderliche Anpresskraft um bis zu 50 %, während die Bohrgeschwindigkeit um bis zu 40 % steigen kann. Diese Kombination ermöglicht schnellere Arbeitszyklen bei gleichzeitig geringerem Kraftaufwand, was besonders in Serienarbeiten und bei der Bearbeitung harter Materialien Zeit und Ressourcen spart. Präzision und Stabilität bei Metallbearbeitung Mit einem Durchmesser von 6,6 mm fällt das Werkzeug in den Standard-Bereich (2,0–13,0 mm) und eignet sich damit besonders für Werkstatt, Montage und DIY-Anwendungen an Stahl, Guss und Nichteisenmetallen. Die kurze Ausführung reduziert die Auskraglänge und minimiert dadurch Vibrationen und Ausschlag, was die Präzision erhöht und saubere Bohrbilder selbst bei Handbohrmaschinen ermöglicht. Dadurch wird das Risiko von Bohrerwandern reduziert und das Ergebnis bleibt reproduzierbar. Geschliffene Ausführung und Spitzenwinkel für harte Werkstoffe Die geschliffene Fertigung (geschliffen) sorgt für scharfe Schneidkanten und hohe Rundlaufgenauigkeit, ideal für legierte und unlegierte Stähle, Temperguss und Hartkunststoffe. Der 135° Spitzenwinkel wurde gewählt, um das Anbohren in harten Werkstoffen zu erleichtern und die Anbohrzeit zu verkürzen. Bei stationärem Einsatz mit Kühlung erzielt die geschliffene Geometrie besonders saubere Bohrlöcher; bei Handbetrieb ist auf kontrollierte Vorschubgeschwindigkeit zu achten, um Bruchgefahr zu minimieren. Zielgruppe, Anwendungstipps und Sicherheitshinweise Das Werkzeug richtet sich an Handwerker, Maschinenbauer und anspruchsvolle Heimwerker, die Wert auf Stabilität und saubere Bohrbilder legen. Für beste Ergebnisse wird vor dem Endbohren ein Zentrierbohrer empfohlen, bei tieferen Bohrungen mehrstufiges Aufbohren verwenden. Zur Verlängerung der Standzeit Kühlung und passende Schnittgeschwindigkeit wählen. Bei Unsicherheit zu Anwendung oder Maschine bietet METAV kompetente Beratung an. Empfehlung: Mit dem MetavCUT HSS-G Spiralbohrer in kurzer Ausführung investieren Sie in langlebige Präzision und effiziente Metallbearbeitung; bei Fragen zur Auswahl oder Anwendung berät METAV Werkzeuge gerne persönlich per eMail info@metav-werkzeuge.com oder Telefon +49 2822 7131930 Bezeichnung: Spiralbohrer Marke: MetavCUT SKU: 45066-FDA Durchmesser: 6,6 mm Spitzenwinkel: 135° Material: HSS-G Norm: DIN 338 Ausführung: kurz Schaft Ausführung: geschliffen Spirallänge: 63 mm Gesamtlänge: 101 mm Typ: Typ N Farbe: blank Für Bohrmaschine: Handbohrmaschine Modellserie: Standard Line Verpackungseinheit: 10 Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ Ist der Spiralbohrer von MetavCUT für Edelstahl geeignet? Der MetavCUT Spiralbohrer mit 135° Spitzenwinkel und HSS-G Material ist für härtere Werkstoffe wie Edelstahl geeignet; dabei werden langsame Schnittgeschwindigkeit und Kühlung empfohlen, um Spitzenhaltbarkeit zu erhöhen. Kann der Spiralbohrer im Akkubohrer verwendet werden? Der kurze MetavCUT Spiralbohrer eignet sich prinzipiell für Handbohrmaschinen, allerdings sind bei Akkugeräten auf ausreichende Leistung und sauberen Rundlauf zu achten, um Bruch zu vermeiden. Was bedeutet geschliffen beim MetavCUT Spiralbohrer? Geschliffen beschreibt die Herstellung der Spanuten und Geometrie im Bohrling; beim MetavCUT Spiralbohrer sorgt das für scharfe Kanten, hohe Rundlaufgenauigkeit und saubere Bohrbilder, besonders bei stationärem Einsatz. Welche Vorteile bietet die kurze Ausführung des Spiralbohrers? Die kurze Ausführung des MetavCUT Spiralbohrers erhöht die Stabilität durch geringere Auskraglänge, reduziert Vibrationen und ermöglicht präziseres Bohren in harten Materialien. {"@context":"https://schema.org","@graph":[{"@type":"Product","@id":"#45066-FDA","sku":"45066-FDA","mpn":"45066-FDA","name":"Spiralbohrer 45066-FDA","description":"Kurzer Spiralbohrer HSS-G Ø 6,6 mm, Spitzenwinkel 135°, Typ N, geschliffener Zylinderschaft, blank, nach DIN 338; geeignet für Metallbearbeitung, hohe Stabilität und präzise Bohrbilder.","image":["https://files.plytix.com/api/v1.1/file/public_files/pim/assets/57/c3/98/62/6298c3575d155f1bc7e497fd/images/8e/48/c5/69/69c5488eb2b3400ba580741b/logo-metav-1200-1200.png","https://files.plytix.com/api/v1.1/file/public_files/pim/assets/57/c3/98/62/6298c3575d155f1bc7e497fd/images/8e/48/c5/69/69c5488eb2b3400ba580741e/logo-metav-1200-900.png","https://files.plytix.com/api/v1.1/file/public_files/pim/assets/57/c3/98/62/6298c3575d155f1bc7e497fd/images/8e/48/c5/69/69c5488eb2b3400ba580741c/logo-metav-1200-675.png"],"additionalProperty":[{"@type":"PropertyValue","name":"Bezeichnung","value":"Spiralbohrer"},{"@type":"PropertyValue","name":"Marke","value":"MetavCUT"},{"@type":"PropertyValue","name":"Durchmesser","value":"6,6 mm"},{"@type":"PropertyValue","name":"Spitzenwinkel","value":"135°"},{"@type":"PropertyValue","name":"Typ","value":"Typ N"},{"@type":"PropertyValue","name":"Farbe","value":"blank"},{"@type":"PropertyValue","name":"Ausführung","value":"kurz"},{"@type":"PropertyValue","name":"Norm","value":"DIN 338"},{"@type":"PropertyValue","name":"Material","value":"HSS-G"},{"@type":"PropertyValue","name":"Schaft Ausführung","value":"geschliffen"},{"@type":"PropertyValue","name":"Spirallänge","value":"63 mm"},{"@type":"PropertyValue","name":"Gesamtlänge","value":"101 mm"},{"@type":"PropertyValue","name":"Für Bohrmaschine","value":"Handbohrmaschine"},{"@type":"PropertyValue","name":"Modellserie","value":"Standard Line"},{"@type":"PropertyValue","name":"Verpackungseinheit","value":"10"},{"@type":"PropertyValue","name":"Hersteller","value":"Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com"}]},{"@type":"FAQPage","mainEntity":[{"@type":"Question","name":"Ist der Spiralbohrer von MetavCUT für Edelstahl geeignet?","acceptedAnswer":{"@type":"Answer","text":"Der Spiralbohrer von MetavCUT, HSS-G, Ø 6,6 mm, Spitzenwinkel 135° und Typ N, eignet sich für härtere Werkstoffe wie Edelstahl; langsame Schnittgeschwindigkeit und Kühlung werden empfohlen, um die Spitzenhaltbarkeit zu erhöhen."}},{"@type":"Question","name":"Kann der Spiralbohrer im Akkubohrer verwendet werden?","acceptedAnswer":{"@type":"Answer","text":"Der kurze Spiralbohrer von MetavCUT mit geschliffenem Zylinderschaft eignet sich prinzipiell für den Einsatz in Handbohrmaschinen und damit auch in Akkubohrern, sofern Leistung und Rundlauf des Akkugeräts ausreichend sind."}},{"@type":"Question","name":"Was bedeutet geschliffen beim MetavCUT Spiralbohrer?","acceptedAnswer":{"@type":"Answer","text":"Geschliffen bedeutet, dass die Spannuten und Geometrie im Bohrling durch Schleifen hergestellt werden; beim MetavCUT Spiralbohrer führt das zu scharfen Schneidkanten, hoher Rundlaufgenauigkeit und sauberen Bohrbildern, besonders bei stationärem Einsatz mit Kühlung."}},{"@type":"Question","name":"Welche Vorteile bietet die kurze Ausführung des Spiralbohrers?","acceptedAnswer":{"@type":"Answer","text":"Die kurze Ausführung des MetavCUT Spiralbohrers reduziert die Auskraglänge, erhöht die Stabilität, minimiert Vibrationen und ermöglicht präziseres Bohren in harten Materialien wie legierten und unlegierten Stählen."}}]},{"@type":"ItemPage","url":"https://metav-shop.de/45066-FDA","dateModified":"2026-05-04T12:00:00+01:00","author":{"@type":"Person","name":"Stephan Bayer","url":"https://www.linkedin.com/in/stephan-bayer/"},"publisher":{"@type":"Organization","name":"Metav Werkzeuge GmbH","url":"https://metav-shop.de","logo":{"@type":"ImageObject","url":"https://files.plytix.com/api/v1.1/file/public_files/pim/assets/57/c3/98/62/6298c3575d155f1bc7e497fd/images/8e/48/c5/69/69c5488eb2b3400ba580741c/logo-metav-1200-675.png","width":1200,"height":675},"address":{"@type":"PostalAddress","streetAddress":"Parkring 45","postalCode":"46446","addressLocality":"Emmerich","addressCountry":"DE"},"telephone":"+49 2822 7131930","email":"info@metav-werkzeuge.com"},"about":[{"@type":"Thing","name":"Spiralbohrer HSS-G"},{"@type":"Thing","name":"Kurz Ausführung für erhöhte Stabilität"},{"@type":"Thing","name":"DIN 338 Zylinderschaft"}],"mentions":[{"@type":"Thing","name":"MetavCUT"},{"@type":"Thing","name":"geschliffener Zylinderschaft"},{"@type":"Thing","name":"Typ N Spiralbohrer"}]}]}

Spiralbohrer – kurzer HSS‑G 6,6 mm, 135° Spitzenwinkel, Typ N, blank, geschliffen, DIN 338 von MetavCUT Der Spiralbohrer ist ein kurzer HSS‑G Metallbohrer für präzise Bohrungen in legierten und unlegierten Stahl sowie Gusswerkstoffe und eignet sich für Stationär‑ und Handbohrmaschinen. Kurze Ausführung für maximale Stabilität Geschliffenes HSS‑G für präzise Metallbohrungen Spitzenwinkel 135° reduziert Anbohrdauer bei harten Werkstoffen Zylinderschaft nach DIN 338 für sichere Aufnahme Geeignet für Handbohrmaschine und Werkstatt Kurzbauweise für weniger Vibration und höhere Genauigkeit Die kurze Bauform sorgt für eine deutlich höhere Stabilität und verringert das Risiko von Durchbiegung oder Verkantung bei der Bohrung. Durch die reduzierte Auskraglänge kann mit gleichbleibendem Vorschub gearbeitet werden, was saubere Bohrbilder und gleichmäßige Bohrungen in Metall ermöglicht. Der Einsatz in der Werkstatt oder auf Stationärmaschinen profitiert von geringerer Werkzeugbeanspruchung und konstanter Schnittlage. Geschliffenes HSS‑G für saubere Lochränder und hohe Schnittgeschwindigkeit Das Material HSS‑G und die geschliffene Ausführung garantieren sehr scharfe Schneiden und eine hohe Rundlaufgenauigkeit. Im Gegensatz zur rollgewalzten Herstellung erzeugt der CNC‑Schliff definierte Spanräume und präzise Geometrien, was zu saubereren Lochrändern führt. Der 135° Spitzenwinkel ist speziell auf härtere Werkstoffe abgestimmt und reduziert das Anbohren, sodass die Schnittgeschwindigkeit erhöht und die Anpresskraft reduziert wird. Vielseitige Anwendung im Standard‑Bereich für Werkstatt und Montage Mit einem Durchmesser von 6,6 mm fällt dieses Werkzeug in den Standard‑Bereich und ist ideal für alltägliche Metallarbeiten, Montage und Reparatur. Der Typ N Normalspiral‑Anschnitt meistert dünne bis mittlere Bleche, Profile und Gusswerkstoffe zuverlässig. Zur Optimierung der Standzeit empfiehlt sich vor dem Bohren Anpunkten, Kühlschmierstoff bei dichten Werkstoffen und das Vermeiden von zu tiefen Sacklochbohrungen ohne Zwischenspannung. Pflegehinweise und Arbeitssicherheit für langlebigen Einsatz Für eine lange Lebensdauer sollten Bohrer regelmäßig gereinigt und bei Bedarf nachgeschliffen oder ersetzt werden, um beschädigte Schneiden zu vermeiden. Kühlung reduziert thermische Belastung und verhindert übermäßigen Verschleiß bei Temperguss oder Edelstahl. Die Profi Line Ausführung von MetavCUT steht für verlässliche Qualität in der Werkstatt und erleichtert präzises, sicheres Arbeiten auch bei anspruchsvollen Metallbohrungen. Empfehlung: Den MetavCUT Profi Line Kurzspiralbohrer mit HSS‑G für präzise Metallbohrungen auswählen und bei Fragen zur Anwendung oder zur passenden Maschine die kompetente Beratung von METAV Werkzeuge per eMail info@metav-werkzeuge.com oder Telefon +49 2822 7131930 in Anspruch nehmen Technische Daten Bezeichnung: Spiralbohrer Marke: MetavCUT SKU: 48066-FDA Durchmesser: 6,6 mm Material: HSS‑G Ausführung: kurz Schaft‑Ausführung: geschliffen Spitzenwinkel: 135° Gesamtlänge: 109 mm Spirallänge: 69 mm Typ: Typ N Norm: DIN 338 Farbe: blank Für Bohrmaschine: Handbohrmaschine Modellserie: Profi Line Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ Für welche Materialien ist der Spiralbohrer von MetavCUT geeignet? Der Spiralbohrer von MetavCUT in Typ N mit HSS‑G ist ausgelegt für legierten und unlegierten Stahl, Gussstahl, Gusseisen, Sintereisen, Temperguss, Nichteisenmetalle und Hartkunststoff und liefert bei diesen Werkstoffen besonders saubere Bohrbilder. Kann der Spiralbohrer von MetavCUT in einer Handbohrmaschine verwendet werden? Ja, der Spiralbohrer von MetavCUT ist für den Einsatz in Handbohrmaschine geeignet, wobei bei 6,6 mm Durchmesser auf zentrisches Anpunkten und angemessene Kühlung geachtet werden sollte, um Bruch und Überhitzung zu vermeiden. Was bedeutet geschliffen beim Spiralbohrer MetavCUT und warum ist das wichtig? Bei dem geschliffenen Spiralbohrer von MetavCUT werden die Spanräume mittels CNC‑Schliff erzeugt, was sehr scharfe Kanten und höhere Rundlaufgenauigkeit ergibt; das führt zu präziseren Bohrlöchern in harten Werkstoffen. Wie pflege ich den MetavCUT Spiralbohrer richtig, um die Standzeit zu verlängern? Scharfe Kanten regelmäßig prüfen, bei Bedarf nachschleifen oder austauschen, Kühlschmierstoff einsetzen und Überhitzung vermeiden, dann bleibt der MetavCUT Spiralbohrer länger leistungsfähig und sicher in der Anwendung. {"@context":"https://schema.org","@graph":[{"@type":"Product","@id":"#48066-FDA","sku":"48066-FDA","mpn":"48066-FDA","name":"Spiralbohrer 48066-FDA","description":"Kurzer HSS‑G Spiralbohrer 6,6 mm, 135° Spitzenwinkel, Typ N, blank, geschliffen, DIN 338; präzise Metallbohrungen in legiertem und unlegiertem Stahl sowie Gusswerkstoffen; geeignet für Handbohrmaschine und Stationärmaschinen.","image":["https://files.plytix.com/api/v1.1/file/public_files/pim/assets/57/c3/98/62/6298c3575d155f1bc7e497fd/images/8e/48/c5/69/69c5488eb2b3400ba580741b/logo-metav-1200-1200.png","https://files.plytix.com/api/v1.1/file/public_files/pim/assets/57/c3/98/62/6298c3575d155f1bc7e497fd/images/8e/48/c5/69/69c5488eb2b3400ba580741e/logo-metav-1200-900.png","https://files.plytix.com/api/v1.1/file/public_files/pim/assets/57/c3/98/62/6298c3575d155f1bc7e497fd/images/8e/48/c5/69/69c5488eb2b3400ba580741c/logo-metav-1200-675.png"],"additionalProperty":[{"@type":"PropertyValue","name":"Bezeichnung","value":"Spiralbohrer"},{"@type":"PropertyValue","name":"Durchmesser","value":"6,6 mm"},{"@type":"PropertyValue","name":"Spitzenwinkel","value":"135°"},{"@type":"PropertyValue","name":"Typ","value":"Typ N"},{"@type":"PropertyValue","name":"Farbe","value":"blank"},{"@type":"PropertyValue","name":"Ausführung","value":"kurz"},{"@type":"PropertyValue","name":"Norm","value":"DIN 338"},{"@type":"PropertyValue","name":"Material","value":"HSS‑G"},{"@type":"PropertyValue","name":"Schaft‑Ausführung","value":"geschliffen"},{"@type":"PropertyValue","name":"Gesamtlänge","value":"109 mm"},{"@type":"PropertyValue","name":"Spirallänge","value":"69 mm"},{"@type":"PropertyValue","name":"Für Bohrmaschine","value":"Handbohrmaschine"},{"@type":"PropertyValue","name":"Modellserie","value":"Profi Line"},{"@type":"PropertyValue","name":"Hersteller","value":"MetavCUT"},{"@type":"PropertyValue","name":"Anwendung","value":"Bohrer für Metall"}]},{"@type":"FAQPage","mainEntity":[{"@type":"Question","name":"Für welche Materialien ist der Spiralbohrer geeignet?","acceptedAnswer":{"@type":"Answer","text":"Der Spiralbohrer von MetavCUT, ein kurzer HSS‑G Spiralbohrer 6,6 mm Typ N, ist geeignet für legierten und unlegierten Stahl, Gussstahl, Gusseisen, Sintereisen, Temperguss, Nichteisenmetalle und Hartkunststoff und liefert besonders saubere Bohrbilder."}},{"@type":"Question","name":"Kann der Spiralbohrer in einer Handbohrmaschine verwendet werden?","acceptedAnswer":{"@type":"Answer","text":"Ja, der MetavCUT Spiralbohrer 6,6 mm Typ N kann in einer Handbohrmaschine verwendet werden; zentrisches Anpunkten und angemessene Kühlung werden für sicheren Einsatz empfohlen."}},{"@type":"Question","name":"Was bedeutet geschliffen und warum ist das wichtig?","acceptedAnswer":{"@type":"Answer","text":"Geschliffen bedeutet, dass die Spannuten und Geometrie mittels CNC‑Schliff erzeugt wurden; der geschliffene HSS‑G Spiralbohrer von MetavCUT bietet dadurch sehr scharfe Kanten, hohe Rundlaufgenauigkeit und saubere, präzise Bohrlöcher in harten Werkstoffen."}},{"@type":"Question","name":"Welche Vorteile hat die kurze Ausführung des Spiralbohrers?","acceptedAnswer":{"@type":"Answer","text":"Die kurze Ausführung des MetavCUT Spiralbohrers 6,6 mm reduziert Vibration und Durchbiegung, erhöht die Stabilität bei der Bohrung und ermöglicht gleichbleibenden Vorschub für saubere Bohrbilder in Metall."}},{"@type":"Question","name":"Wie verlängere ich die Standzeit des Spiralbohrers?","acceptedAnswer":{"@type":"Answer","text":"Für längere Standzeit den MetavCUT Spiralbohrer sauber halten, scharfe Kanten überprüfen, bei Bedarf nachschleifen oder ersetzen und bei dichten Werkstoffen Kühlmittel einsetzen, um Überhitzung zu vermeiden."}}]},{"@type":"ItemPage","url":"https://metav-shop.de/product/48066-FDA","dateModified":"2026-05-04T12:00:00+01:00","author":{"@type":"Person","name":"Stephan Bayer","url":"https://www.linkedin.com/in/stephan-bayer/"},"publisher":{"@type":"Organization","name":"Metav Werkzeuge GmbH","url":"https://metav-shop.de","logo":{"@type":"ImageObject","url":"https://files.plytix.com/api/v1.1/file/public_files/pim/assets/57/c3/98/62/6298c3575d155f1bc7e497fd/images/8e/48/c5/69/69c5488eb2b3400ba580741c/logo-metav-1200-675.png","width":1200,"height":675},"address":{"@type":"PostalAddress","streetAddress":"Parkring 45","postalCode":"46446","addressLocality":"Emmerich","addressCountry":"DE"},"telephone":"+49 2822 7131930","email":"info@metav-werkzeuge.com"},"about":[{"@type":"Thing","name":"Spiralbohrer Kurzausführung"},{"@type":"Thing","name":"HSS‑G für Metallbearbeitung"},{"@type":"Thing","name":"DIN 338 Zylinderschaft"}],"mentions":[{"@type":"Thing","name":"Typ N Normalspiral"},{"@type":"Thing","name":"Geschliffene Ausführung (HSS‑G)"},{"@type":"Thing","name":"Geeignet für Handbohrmaschine und Stationärmaschinen"}]}]}