High-precision drills for reliable, high-throughput metalworking
Drills provide the fundamental rotating cutting solution for producing accurate cylindrical holes in materials such as structural steel, high-alloy stainless steel, cast iron, non-ferrous metals and engineering plastics, delivering consistent hole quality and extended tool life in CNC machining and turning centres. This category covers everything from classic twist drill made from high-speed steel for general machining to solid carbide drill optimised for high cutting speeds and long run times, offering advanced coatings and internal coolant options for improved heat management. By using optimised point geometries and split points the tools reduce thrust, prevent walking at the start of the cut and ensure superior surface finish, which benefits sectors from general mechanical engineering to automotive component manufacture.
5mm NC Spot Drill HSS-Co 90° Right-Hand Cylindrical Shank DIN 1835-A, h8 - TECWERK
Benefit from precise centring and reduced cycle times thanks to the combination of HSS‑Co construction and a 90° tip, together with a DIN 1835‑A cylindrical shank for secure clamping; order directly via Metav Werkzeuge or consult our specialists for application advice. NC spot drill 5 mm HSS‑Co (90° tip) – TECWERK The NC spot drill 5 mm HSS‑Co is a centre‑drilling tool designed for position‑accurate and rapid spot drilling and chamfering on NC machines and drilling rigs. HSS‑Co cutting edge for extended wear resistance 90° tip for precise centring and chamfering Cylindrical shank to DIN 1835‑A for secure mounting Right‑hand cut for standard machining feeds Precision where it matters: accurate centring and chamfering in one pass The robust HSS‑Co construction delivers elevated heat resistance and wear performance compared with plain high‑speed steel, enabling longer tool life under cyclic NC operation. The 90° tip is optimised for reliable centring and simultaneous chamfering of threaded holes, which reduces handling and secondary operations. With a recommended feed of 0.04 mm/rev in steel up to 800 N, the tool supports consistent hole geometry and repeatable results in high‑volume production. Secure clamping and dimensional consistency for efficient setups Equipped with a cylindrical shank to DIN 1835‑A, the tool ensures a defined and secure interface with standard holders used on machining centres and drill rigs. The nominal diameter tolerance h8 supports interchangeability and low runout, while the overall length of 62 mm and spiral length of 14 mm offer the necessary reach and chip evacuation for typical spot‑drilling tasks. These features simplify tool changes and help maintain machining accuracy across batches. Durable performance that supports productivity on NC platforms Right‑hand cutting geometry and the HSS‑Co compound provide a balance of toughness and hardness that is suited to repetitive positioning and rapid probing operations. The tool is specifically configured for position‑accurate and rapid anboring on NC machines and drilling machines, enabling centres and chamfers to be produced in a single operation and thereby shortening cycle times. Supplied as single units, the design emphasises reliability and predictable integration into established tool lists. For application guidance or to procure TECWERK centre‑drilling tools, contact Metav Werkzeuge in Emmerich at info@metav-werkzeuge.com or call +49 2822 7131930 for personalised advice and supply from our European stock Technical data SKU: 2000860105NW Label: NC spot drill 5 mm HSS‑Co 90° TECWERK Standard: DIN 1835‑A Manufacturer: TECWERK Material: HSS‑Co Shank: Cylindrical shank Cutting direction: Right‑hand cut Facts Diameter: 5 mm Total length: 62 mm Spiral length: 14 mm Tip angle: 90° Tolerance diameter: h8 Feed in steel ≤ 800 N: 0.04 mm/rev Packaging unit: 1 Special features For position‑accurate, rapid spot drilling on NC machines and drilling rigs Centring and chamfering of thread holes in one pass Cylindrical shank to DIN 1835‑A Right‑hand cut HSS‑Co material FAQ What machines is this tool suitable for? The NC spot drill 5 mm HSS‑Co (TECWERK, SKU 2000860105NW) is intended for use on NC machines and drilling rigs for position‑accurate spot drilling and chamfering. What feed should be used for reliable results? For the TECWERK 5 mm spot drill a feed of approximately 0.04 mm/rev in steel up to 800 N is recommended to maintain consistent hole quality. How is the tool mounted in the spindle? The cylindrical shank to DIN 1835‑A and the diameter tolerance h8 ensure secure clamping and low runout when the tool is held in compatible tool holders. What advantage does the 90° tip provide? The 90° tip on this centre‑drilling tool produces precise centring and a suitable chamfer in a single operation, reducing the need for secondary processes. Why choose HSS‑Co for this application? HSS‑Co offers improved hot hardness and wear resistance compared with standard high‑speed steel, delivering longer life under the repeated demands of NC spot‑drilling operations. TECWERK: Manufacturer / Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund
5mm NC Spot Drill HSS‑Co TiN 90° Cylindrical Shank h8, DIN 1835-A - TECWERK
Taking advantage of a HSS‑Co substrate with a TiN coating and a 90° tip, this spot drill combines robust wear resistance with reliable centring and chamfering in a single pass; order the tool directly via Metav Werkzeuge or consult the specialists for application advice. NC spot drill 5 mm, HSS‑Co, TiN, 90° — TECWERK NC spot drill 5 mm for precise positioning and chamfering on CNC machines and drilling centres HSS‑Co substrate for high durability TiN coating for enhanced wear resistance Cylindrical shank to DIN 1835‑A 90° tip for centring and chamfering Faster, more reliable positioning for machining workflows The spotting tool is designed to provide precise positioning and stable starts on automated equipment. With a 5 mm diameter and a 90° tip geometry, the tool enables accurate centring and initial chamfering in the same operation, reducing secondary set‑ups and downtime. This combination is particularly effective on CNC machines and drilling centres where repeatability is essential; the result is fewer rejected parts and a smoother production flow. Durable construction for extended service life Manufactured from HSS‑Co, the drill body offers improved toughness and thermal resistance compared with high‑speed steel alone. The TiN coating gives an additional wear barrier that reduces flank and crater wear, allowing for longer tool life and fewer changeovers. For workshops that prioritise uptime, this material and coating pairing means more consistent hole starts at higher utilisation rates without sacrificing surface condition. Standards, shank design and recommended operating data The tool is supplied with a cylindrical shank conforming to DIN 1835‑A, ensuring secure, repeatable clamping in standard toolholders and chucks. Spiral length is 14 mm with an overall length of 62 mm, and the diameter tolerance is h8, providing predictable fit and concentricity. The cutter is right‑hand cutting; a recommended feed in steel up to 800 N is 0.04 mm/rev, which balances tool life and surface quality. These specifications simplify integration into existing setups and support consistent cycle times. Contact Metav Werkzeuge for tailored advice on TECWERK HSS‑Co spot drills and compatibility with existing CNC processes — Metav Werkzeuge is available to advise from Emmerich Technical data Article number: 2000861385NW Manufacturer: TECWERK Product type: NC spot drill Facts Diameter: 5 mm Overall length: 62 mm Spiral length: 14 mm Tip angle: 90° Diameter tolerance: h8 Packaging unit: 1 Special features Material: HSS‑Co Coating: TiN Shank: cylindrical shank to DIN 1835‑A Cutting direction: right‑hand cutting Application: positioning and fast spot drilling on NC machines and drilling centres Additional data: recommended feed in steel up to 800 N: 0.04 mm/rev FAQ How does the 90° tip help with centring and chamfering? The 90° tip on the NC spot drill 5 mm creates a defined cone for easy centring and simultaneous chamfering of threaded starts, reducing the need for follow‑up operations. Is the shank compatible with standard holders? Yes; the cylindrical shank conforms to DIN 1835‑A so it is compatible with standard chucks and toolholders used on CNC machines. What advantages does the TiN coating provide? TiN coating on the TECWERK NC spot drill improves wear resistance and heat protection, which extends tool life and maintains cutting performance under frequent use. Can the tool be used for automated production runs? The combination of HSS‑Co material, TiN coating and DIN‑standard shank makes the tool suitable for automated NC and CNC processes where repeatability and tool life are required. Manufacturer / Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund
5mm NC Spot Drill Solid Carbide 120° Tip Cylindrical Shank DIN 6535-HA, h6 - TECWERK
Take advantage of the combination of solid carbide construction, a 120° centring tip and a cylindrical shank to DIN 6535-HA for precise, time-saving first operations; order directly via Metav Werkzeuge or consult our specialists for application-specific advice. TECWERK NC Spot Drill D 5 mm — Solid carbide, 120° tip The TECWERK NC Spot Drill D 5 mm is a precision centre‑drilling tool designed for position‑accurate and fast spotting on NC machines and drilling centres Solid carbide construction VHM 120° tip for accurate centring Cylindrical shank to DIN 6535-HA Suited to high-strength and stainless steels Faster, more accurate centring and chamfering in one pass The combination of a 120° tip and a short flute geometry enables reliable centring and light chamfering in a single operation, reducing setup time and tool changes. Solid carbide construction provides a rigid cutting edge that supports position‑accurate drilling on CNC machines and drilling centres. Where repeatable hole location and initial chamfer quality matter, this tool reduces downstream rework and shortens cycle times while maintaining consistent entry geometry. Built for demanding materials and long tool life Manufactured from solid carbide (VHM), the tool is optimised for machining a wide range of materials: high‑strength steels, cast and grey iron, stainless steels and non‑ferrous metals. The cylindrical shank to DIN 6535‑HA ensures secure clamping in standard toolholders, while the tight h6 diameter tolerance supports concentricity and minimal runout. These characteristics combine to give reliable edge stability and longer service intervals under continuous NC operation. Process benefits: reliable feeds, machine compatibility and fewer setups Designed as a right‑hand cutting NC spot drill with a 15 mm flute length and 50 mm overall length, the tool is ready to integrate into automated production sequences. Recommended feed in steel up to 800 N is 0.07 mm/rev, a guideline that helps balance cutting forces and surface finish. The tool’s geometry supports quick engagement and clean dimple formation for subsequent drilling or tapping, improving thread alignment and reducing scrapped parts. This translates into measurable productivity gains in series production. Contact Metav Werkzeuge for specification matching or to discuss batch supply and delivery from our Emmerich location — phone +49 2822 7131930 or eMail info@metav-werkzeuge.com Technical Data Article number: 2000865821NW Standard: DIN 6535-HA Material: VHM (solid carbide) Product type: NC spot drill Diameter: 5 mm Overall length: 50 mm Spiral length: 15 mm Point angle: 120° Cutting direction: right‑hand Shank: cylindrical shank Diameter tolerance: h6 Packaging unit: 1 Core data Diameter: 5 mm Overall length: 50 mm Spiral/flute length: 15 mm Tip angle: 120° Tolerance: h6 Feed recommendation in steel ≤ 800 N: 0.07 mm/rev Special features Solid carbide (VHM) for high rigidity Cylindrical shank to DIN 6535‑HA for standard holders Right‑hand cutting for conventional setups Suitable for high‑strength steels, cast iron, grey cast iron, stainless steels and non‑ferrous metals Combines centring and chamfering in one operation Designed for NC machines and drilling centres FAQ What machines is this spot drill suitable for? The TECWERK NC spot drill D 5 mm is intended for NC machines and drilling centres and is optimised for automated production environments. Can the tool be used on stainless steel? Yes, the solid carbide construction and geometry make the tool suitable for stainless steels as stated in the technical features. What is the recommended feed in steel? A guideline feed in steel up to 800 N is 0.07 mm per revolution to balance surface finish and tool life. How does the DIN 6535-HA shank help in production? The cylindrical shank to DIN 6535‑HA ensures secure clamping in common toolholders, improving concentricity and reducing runout. Manufacturer / Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund
5mm NC Spot Drill Solid Carbide 90° Right-Hand, h6 Shank DIN 6535-HA - TECWERK
Take advantage of precise centring, a solid carbide design and a 90° point for fast, single-pass centring and chamfering — ideal for NC machines and drilling centres. Order the tool directly via Metav Werkzeuge or consult our specialists for application advice. TECWERK NC pilot drill D 5 mm, solid carbide, 90° point The TECWERK NC pilot drill D 5 mm is a solid-carbide pilot drill designed for position-accurate and rapid spot drilling on NC machines and drilling centres, enabling centring and chamfering of threaded holes in a single operation. Solid carbide for high wear resistance 90° point for reliable centring Cylindrical shank to DIN 6535-HA Diameter tolerance h6 for precise fits Faster, more accurate hole starts for serial production A pilot drill in solid carbide delivers consistent results where repeatability matters. The short 15 mm flute and 90° point make it ideally suited for producing exact starting points and small countersinks before tapping. On NC equipment the tool reduces secondary operations by combining centring and chamfering in one pass, which translates into reduced cycle time and fewer set-up interventions. The compact geometry supports stable chip evacuation and repeatable contact with the workpiece, improving hole quality across batches. Robust design that handles demanding materials Constructed from solid carbide, the tool is rated for a broad range of materials: high-strength steels, cast steel, grey cast iron, stainless steels and non-ferrous metals. The right-hand cutting geometry and a diameter tolerance of h6 ensure predictable hole sizes for follow-up threading operations. For tougher steels, a recommended feed of 0.07 mm/rev at cutting forces up to 800 N balances tool life and surface finish. The DIN 6535-HA cylindrical shank supports secure clamping and concentricity in standard toolholders, reducing vibration and extending service life. Made to integrate with NC workflows and reduce rework The compact overall length and standard shank make this pilot drill straightforward to program into existing tool libraries on CNC lathes, milling machines and drilling centres. By combining positioning, centring and deburring in one operation, the tool lowers handling and inspection needs — delivering consistent results and less rework. For workshops looking to scale precision without complex procedures, the combination of standard interfaces and wear-resistant material enables steady production rates and reliable hole geometry across shifts. For precise, workshop-ready pilot drilling with TECWERK solid-carbide tooling, contact Metav Werkzeuge for tailored advice and dependable supply from Emmerich. Technical data Article number: 2000865803NW Manufacturer: TECWERK Product type: NC pilot drill Standard: DIN 6535-HA Specifications Diameter: 5 mm Overall length: 50 mm Flute / spiral length: 15 mm Point angle: 90° Shank type: Cylindrical shank Diameter tolerance: h6 Cutting direction: Right-hand Applications & features Solid carbide (VHM) Position-accurate and fast spot drilling on NC machines and drilling centres Centring and chamfering of threaded holes in a single pass Suitable for high-strength steels, cast steel, grey cast iron, stainless steels and non-ferrous metals Recommended feed in steel up to 800 N: 0.07 mm/rev Packaging unit: 1 FAQ Which materials are suitable for this pilot drill? The TECWERK NC pilot drill D 5 mm is designed for high-strength steels, cast steel, grey cast iron, stainless steels and various non-ferrous metals, offering reliable starts and clean centring. Can the tool centre and chamfer in one operation? Yes — the geometry of this solid-carbide pilot drill allows centring and small chamfering of threaded holes in a single pass, reducing the number of machining steps. What shank standard is used and why does it matter? A cylindrical shank to DIN 6535-HA is used for secure clamping and concentricity in standard toolholders; this improves stability and repeatability in NC machining. What feed should be used for steel applications? For steel up to 800 N cutting force a feed of around 0.07 mm/rev is recommended to balance tool life and finish when using this pilot drill (SKU 2000865803NW). Manufacturer/Responsible: NORDWEST Handel AG, Robert-Schuman-Straße 17, 44263 Dortmund
5mm NC Spot Drill Solid Carbide TiAlN Coated 142° Point, DIN 6535-HA - TECWERK
Precise centring, high wear resistance and a DIN‑compliant cylindrical shank combine to reduce set‑up time and ensure repeatable results — with a TiAlN‑coated solid carbide tip and 142° point angle for reliable centring and chamfering; order directly via Metav Werkzeuge or consult the specialists for application support. TECWERK NC spot drill D 5 mm — Solid carbide, TiAlN, 142° A TECWERK NC spot drill D 5 mm designed for fast, position‑accurate spotting, centring and simultaneous chamfering of threaded holes on CNC machines and drilling centres. Solid carbide with TiAlN coating 142° precision point for clean centring Cylindrical shank to DIN 6535‑HA Suited for high‑strength steels and stainless steels Consistent centring and long tool life for CNC production The TECWERK NC spot drill D 5 mm combines solid carbide construction with a TiAlN surface finish to deliver high wear resistance in demanding production environments. The 142° point angle produces a concise, stable centre that reduces wandering at plunge start, while the coating increases heat resistance during frequent cycle starts. This results in fewer tool changes and more consistent hole preparation across batches, supporting efficient machining on modern CNC machines. Accurate clamping and concentricity with DIN cylindrical shank A cylindrical shank manufactured to DIN 6535‑HA with a h6 diameter tolerance ensures precise seating in standard toolholders and automatic chucks. The tight tolerance reduces run‑out and improves concentricity between the spot drill and subsequent twist drills, lowering the risk of misaligned threads. For workshops that use automated spindles or quick‑change systems, the DIN shank provides a dependable interface for repeatable results. Designed for tough materials and one‑pass preparation This spot drill is optimised for a wide material range: high‑strength steels, cast steels, grey cast iron, stainless steels and non‑ferrous metals. The tool features right‑hand cutting and is rated for a practical feed of 0.07 mm/rev in steel up to 800 N, allowing controlled material removal during the spotting operation. By centring and chamfering in one pass, the cutter shortens the process chain, delivering prepared holes ready for threaded operations with improved axial alignment. Practical compatibility and application benefits The geometry is matched to centre standard twist drills with point angles from 120–140°, so the spot drill works as a reliable lead‑in for common drill types. Its design supports fast, position‑accurate spotting on NC machines and drilling centres, improving process stability and reducing setup iterations. The combination of carbide body and protective coating keeps the cutter productive under repetitive spotting cycles typical in industrial production. For professional centring and clean chamfers, contact Metav Werkzeuge for tailored application advice and supply from Emmerich — our specialists will recommend the best configuration for the production requirements. Technical Data Article number: 2000865839NW Norm: DIN 6535‑HA Manufacturer: TECWERK Product type: NC spot drill Material: VHM (solid carbide) Coating: TiAlN Cutting direction: right‑hand Shank execution: Cylindrical shank Tolerance diameter: h6 Facts Diameter: 5 mm Overall length: 50 mm Spiral length: 15 mm Point angle: 142° Feed in steel up to 800 N: 0.07 mm/rev Special features Solid carbide body TiAlN coating for heat and wear resistance Cylindrical shank to DIN 6535‑HA Right‑hand cutting Suited for high‑strength steels, cast steel, grey cast iron, stainless steels and non‑ferrous metals Centres twist drills with point angles of 120–140° FAQ What materials is this spot drill suitable for? The TECWERK NC spot drill D 5 mm is suited to high‑strength steels, cast steel, grey cast iron, stainless steels and non‑ferrous metals as indicated in the technical data. Will the shank fit standard CNC toolholders? Yes. The cylindrical shank is made to DIN 6535‑HA with a h6 tolerance for secure seating in standard chucks and toolholders. What advantage does the 142° point angle provide? A 142° point produces a stable, narrow centre that reduces wandering on plunge start and provides a clean chamfer for subsequent threading or drilling operations. Can this be used to centre twist drills? Yes. The geometry is compatible with twist drills that have point angles between 120° and 140°, enabling reliable transfer from spotting to drilling. What cutting data should be used as a guideline? A practical reference is a feed of 0.07 mm/rev in steel up to 800 N; actual parameters should be adjusted to machine rigidity and material condition. Manufacturer/Responsible: NORDWEST Handel AG; Robert‑Schuman‑Straße 17; 44263 Dortmund
5mm NC Spot Drill Solid Carbide TiAlN Coating 90° Cylindrical Shank DIN 6535-HA - TECWERK
Benefit from a tool that combines precision centring, high wear resistance and a DIN‑compliant shank to reduce setup time and improve cycle reliability; order the NC spot drill directly via Metav Werkzeuge or ask our consultants if needed. NC spot drill 5 mm, solid carbide, TiAlN – TECWERK The NC spot drill 5 mm, solid carbide, TiAlN is a precision spot‑drilling tool for positionally accurate pre‑drilling, centring and chamfering on CNC machines and drilling rigs. Solid carbide construction for rigidity TiAlN coating for enhanced wear resistance 90° centred tip for precise positioning Cylindrical shank to DIN 6535‑HA Accurate centring from the first touch The 90° tip and tight h6 diameter tolerance ensure reliable centring and precise starts for subsequent drilling or tapping operations. With a nominal diameter of 5 mm and a flute length of 15 mm, the tool provides controlled chip formation and stable seating in the workpiece. The specified feed of 0.07 mm/rev in steel up to 800 N supports consistent hole quality and repeatable positioning, reducing rework and scrap in high‑precision production. Designed for demanding materials and continuous use Made from solid carbide, the spot drill is particularly suited to high‑strength steels, cast iron, stainless steel and many non‑ferrous metals. The TiAlN surface layer increases thermal stability and reduces flank adhesion at elevated cutting temperatures, extending tool life under aggressive cycle conditions. This combination of substrate and coating delivers longer tool life and more predictable wear behaviour in mixed‑material batch production. Fast integration into CNC toolchains A cylindrical shank produced to DIN 6535‑HA guarantees secure clamping in standard toolholders and consistent runout when used in automatic tool changers. The tool’s 50 mm overall length and compact geometry allow close approach to fixtures and reduce tool‑change interference on multi‑spindle heads. Right‑hand cutting direction and the balanced flute geometry simplify programming and help maintain stable chip evacuation during automated cycles. Reduce cycle time with one‑pass operations The geometry enables centring and chamfering of thread starts in a single pass, cutting an operation from several steps to one and improving throughput. Reliable centring and burr‑reduced chamfers mean fewer follow‑up operations and lower inspection overheads. For operations where predictability and repeatability are essential, the tool’s coated carbide construction supports extended runs and minimises unplanned intervention. Contact Metav Werkzeuge for tailored application advice and reliable supply from Emmerich: info@metav-werkzeuge.com, +49 2822 7131930 Technical Data Article number: 2000865812NW Standard: DIN 6535‑HA Product type: NC spot drill Facts Diameter: 5 mm Overall length: 50 mm Flute length: 15 mm Tip angle: 90° Tolerance: h6 Feed in steel up to 800 N: 0.07 mm/rev Cutting direction: right‑hand Special features Material: solid carbide Coating: TiAlN Shank: cylindrical shank to DIN 6535‑HA Application: positionally accurate spot‑drilling, centring and chamfering on CNC machines Suitable for: high‑strength steels, cast iron, grey cast iron, stainless steel, non‑ferrous metals Packaging unit: 1 FAQ What is the primary function of this spot drill? The NC spot drill 5 mm, solid carbide, TiAlN is engineered for positionally accurate pre‑drilling and simultaneous centring and chamfering on CNC machines, enabling one‑pass preparation for subsequent threading or drilling. Which materials can be machined with this tool? TECWERK’s NC spot drill performs well in high‑strength steels, cast iron, grey cast iron, stainless steel and a range of non‑ferrous metals thanks to its solid carbide substrate and TiAlN coating. How does the TiAlN coating benefit process reliability? TiAlN increases thermal resistance and reduces adhesion, so the coated tool sustains higher cutting temperatures with less wear, improving tool life and consistency in long production runs. Is the shank compatible with standard holders? Yes; the cylindrical shank conforms to DIN 6535‑HA, allowing secure clamping in common toolholders and ensuring repeatable runout when used with automatic tool changers. What feed is recommended for steel? For steel up to the stated condition, a feed of 0.07 mm/rev is given for reliable performance; actual feeds should be adjusted based on machine rigidity and workholding. Manufacturer / Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund
6.1mm HSS Twist Drill DIN 338 ,short, roll forged, black, Type N - MetavCUT
Twist Drill — Type N, 6.1 mm, HSS, Short, 118° Tip, Black, DIN 338 by MetavCUT The Twist Drill is a short HSS metal drill designed for precision drilling in steel and non-ferrous metals, suitable for Hand Drills and Drilling Machines. Short HSS design for high stability Conforms to DIN 338 for short cylinder shank drills 118° tip for reliable centring and entry Suitable for alloyed and unalloyed steel and non-ferrous metals Robust black finish for workshop durability Precision and Stability for Metalworking The Twist Drill (MetavCUT, Type N) with a 6.1 mm diameter and 118° tip offers increased rigidity thanks to its Short overall length. This reduced overhang minimises bending and runout, which improves hole accuracy when used in Hand Drills or stationary Drilling Machines. For tasks that demand repeatable, concentric holes in metal, the short geometry delivers better guidance and less vibration than longer bits, resulting in cleaner results and longer tool life. Standardised Short Design for Consistent Results Manufactured to DIN 338, the Twist Drill (MetavCUT, Type N) follows the classification for short spiral drills with cylinder shank. The standard ensures defined dimensions, tolerances and compatibility with common chucks, making tool changeover straightforward. Because the geometry and length are standardised, repeat production and jig-based operations benefit from predictable performance and easier quality control. HSS Material and Application Recommendations Made from HSS (High Speed Steel), this Twist Drill is optimised for standard metalworking tasks. The roll-walzed production process yields a tougher, more elastic flute body that reduces fracture risk, especially for diameters below 6 mm. Recommended materials include alloyed and unalloyed steel, cast iron, non-ferrous metals and many plastics. When used in harder materials, adapted speeds and cutting fluids extend life; for softer materials the 118° tip aids initial centring and reduces walking. Target Users and Practical Advantages Designed for workshops, maintenance technicians and hobbyists who require robust, repeatable drilling in metal, the Twist Drill (MetavCUT, Type N) shines in setups where stability and precision matter. The short execution supports precise manual drilling and machine operations alike. For users unsure about drill selection or compatible machine settings, METAV Werkzeuge offers competent advice to match the drill to the workpiece and machining conditions. Strong recommendation: For reliable metal drilling choose the MetavCUT Twist Drill Type N with 6.1 mm diameter and 118° tip — for personalised technical advice contact METAV Werkzeuge at info@metav-werkzeuge.com or call +49 2822 7131930, WhatsApp +49 170 2837271 Technical Data Designation: Twist Drill / Spiralbohrer Brand: MetavCUT SKU: 40061-FDA Diameter: 6.1 mm Tip angle: 118° Type: Type N Material: HSS (High Speed Steel) Execution: Short Colour: Black Spiral length: 57 mm Total length: 101 mm For use in: Hand Drill / Drilling Machine Standard: DIN 338 Application: Drills for metal Manufacturer: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What is the MetavCUT Twist Drill Type N best used for? The Twist Drill from MetavCUT (Type N) is primarily designed for drilling metal; it is well suited to alloyed and unalloyed steels, cast iron and non‑ferrous metals where a robust, standard short HSS geometry is required. Can the MetavCUT Twist Drill Type N be used in a hand drill? Yes, the Twist Drill (MetavCUT, Type N) is suitable for Hand Drills as well as Drilling Machines; its short overall length increases stability and reduces the risk of breakage during manual operation. For what is a Twist Drill used? A Twist Drill (MetavCUT, Type N) is mainly applied to the machining of high‑strength workpieces and larger hole diameters; its form is easy to resharpen and it withstands higher loads, which makes it the tool of choice for many metalworking tasks. Which three drill types are common? Common drill types include Metal Drill, Wood Drill and Stone/Concrete Drill, and the MetavCUT Twist Drill corresponds to the Metal Drill category. Why are Twist Drills sharpened at the tip? Sharpening reduces the cross‑cut at the tip of the Twist Drill (MetavCUT, Type N), lowering friction forces and thus reducing required feed forces while improving centring in the workpiece. Can a metal Twist Drill be used in wood? A Metal Drill such as the MetavCUT Twist Drill can be used in wood, but it typically provides poorer guidance and a less clean finish than dedicated Wood Drills; however it is easier to resharpen and has lower self‑feeding tendency. For which drilling depths is the Twist Drill most used? A solid hole is commonly executed with a Twist Drill (MetavCUT, Type N). For diameters up to 20 mm and drilling depths up to 100 mm, the Twist Drill is the most frequently used tool. Is HSS or HSSE better? The general assumption that HSSE is always superior to HSS is incorrect; choosing between HSS and HSSE for a MetavCUT Twist Drill (Type N) depends on working conditions and whether the higher acquisition cost of HSSE is justified by the specific application.
6.1mm HSS-E Twist Drill DIN 338 ,short, 5% cobalt-alloyed, Type N - MetavCUT
Spiralbohrer — Twist Drill Type N (Ø 6.1 mm, 135°, short, 5% cobalt-alloyed, HSS‑E, DIN 338) The Spiralbohrer Twist Drill Type N is a short HSS‑E drill designed for precision drilling in metal with enhanced stability and wear resistance. Short design for higher stability 135° point angle for hard materials HSS‑E with 5% cobalt for wear resistance Fully ground shank for precise centring DIN 338 compliance for standardised quality Increased Precision and Stability for Metalworking A short Twist Drill with reduced overall length improves stability and reduces bending during operation, which is especially important when working with tougher metals. The combination of a short design and a fully ground shank ensures consistent concentricity in the chuck and cleaner holes under load. Professionals who demand repeatable, accurate results will value the greater rigidity compared with longer counterparts, making this tool well suited for demanding drilling tasks in workshop and production environments. Material Composition and Why 5% Cobalt Matters The HSS‑E material with 5% cobalt increases hot hardness and wear resistance, allowing the Twist Drill to retain cutting performance at higher temperatures typical when drilling stainless steel and alloyed steels. The cobalt alloy improves service life and reduces frequent regrinding cycles, so fewer tool changes are required during longer runs. For users unfamiliar with HSS‑E, it is a high‑speed steel variant alloyed for improved durability when cutting hard materials. Optimised Geometry for Hard Materials With a 135° point angle and Type N normal spiral geometry, this short Twist Drill is optimised for entering and cutting harder materials while reducing walking and chatter on the surface. The larger point angle reduces the tendency to dig in on the first contact and shortens the effective penetration time, which benefits drilling in stainless steel and similar alloys. For routine metal fabrication tasks where precision and tool life matter, this geometry provides a reliable balance between entry behaviour and chip evacuation. Intended Use and Who Benefits Most Designed primarily as a drill for metal, this Twist Drill Type N suits metalworkers, toolroom technicians and production engineers requiring reliable holes in alloyed and unalloyed steel, cast iron, non‑ferrous metals and plastics. The short execution makes it ideal for bench drills and smaller drilling machines where minimised overhang leads to better outcomes. If the application involves long reach or deep through‑holes, a different drill length should be selected to match the task. Handling, Cooling and Regrinding Tips To get the best lifetime from a short HSS‑E Twist Drill, use appropriate cutting speeds, steady feed and suitable coolant when machining harder alloys. The fully ground flute geometry provides sharp cutting edges and precise hole quality but can be more brittle than rolled alternatives; therefore controlled feeds and coolant reduce thermal stress and risk of breakage. When regrinding, keep the original point geometry to maintain the centring behaviour and the characteristic 135° angle for hard materials. For precise metal drilling choose MetavCUT quality: the short Twist Drill Type N offers the stability and heat resistance that professionals value — for technical questions or personalised advice contact METAV Werkzeuge. 📧 info@metav-werkzeuge.com ☎️ +49 2822 7131930 ✔️ WhatsApp +49 170 2837271 Technical information Designation: Twist Drill Brand: MetavCUT SKU: 47061-FDA Diameter: 6.1 mm Spiral length: 63 mm Overall length: 101 mm Point angle: 135° Type: Type N Execution: short Material: HSS‑E Colour: 5% cobalt-alloyed Shank finish: fully ground For drilling machine: Drilling Machine Norm: DIN 338 Application: Drills for metal Model series: Standard Line Manufacturer: MetavCUT Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What is the Spiralbohrer Twist Drill Type N best used for? The Spiralbohrer Twist Drill Type N by MetavCUT is primarily intended for drilling metal; its short execution and Type N geometry make it particularly suitable for precision holes in alloyed and unalloyed steels, cast iron, non‑ferrous metals and plastics. Can the Spiralbohrer Twist Drill be used on stainless steel and hard alloys? Yes. The Spiralbohrer Twist Drill Type N with HSS‑E material and 5% cobalt from MetavCUT is designed for higher hot hardness and wear resistance, which improves performance when drilling stainless steel and other harder alloys. For what is a Twist Drill used? A Twist Drill is mainly applied when machining high‑strength materials and larger drill diameters. This form is easy to regrind and withstands higher loads, which is why it is commonly used for tougher metalworking operations. Which three drill types exist? The main categories are metal drills, wood drills and stone/concrete drills. Why are Twist Drills tip‑pointed (ausgespitzt)? The tip pointing reduces the cross‑cut at the drill tip, which significantly lowers friction and therefore requires less feed force. At the same time the pointed tip centres the drill more reliably in the workpiece. Can a Twist Drill be used to drill wood? A metal drill can be used in wood, but guidance is poorer and the hole finish is less clean. Metal drills are easier to regrind and have lower self‑feed tendency compared with dedicated wood bits. For which drilling depths is the Twist Drill most used? A solid hole is typically produced with a Twist Drill. For diameters up to 20 mm and depths up to 100 mm, the Twist Drill is the most commonly used tool. Is HSS or HSSE better? The common belief that HSSE steels are always superior to standard HSS is not universally true. When choosing, assess whether your working conditions justify the higher initial cost of HSSE for the expected benefits.
6.1mm HSS-G Twist Drill DIN 338 ,short, bright finished, Type N - MetavCUT
Twist Drill — Type N Short, 6.1 mm, 135° tip, HSS‑G, Bright Finished (DIN 338) The Twist Drill short Type N is a precision Drilling Machine bit designed for stable, fast metalworking, especially suited to hardened materials and demanding workshop applications. Short design for increased rigidity and accuracy Sharp 135° tip for harder materials HSS‑G ground for clean, concentric holes Fully ground shank for excellent runout accuracy Conforms to DIN 338 for short twist drills Engineered for higher drilling performance in metalworking This short Twist Drill from MetavCUT delivers a performance-oriented solution for metal fabrication: the HSS‑G material and optimized geometry enable faster material removal with reduced drilling forces. The ground flute geometry creates very sharp cutting edges that produce clean, precise holes and reduce burr formation. For craftsmen and production workshops, this means shorter cycle times and more reliable hole quality when processing legierte and unlegierte steels, cast steels and non‑ferrous metals. Short length increases rigidity and improves accuracy A reduced overall length significantly reduces the cantilevered section protruding from the chuck, which increases stability and lowers the risk of bending under load. This makes the short Type N Twist Drill particularly suitable for precise operations on a Drilling Machine and for drilling in hard materials where deflection would compromise hole accuracy. Operators will notice improved concentricity and less chatter compared with longer tools. Ground HSS construction explained and practical benefits The designation HSS‑G (ground High Speed Steel) denotes that the flute geometry is produced by CNC grinding rather than rolling. This results in extremely sharp cutting lips and high dimensional accuracy, which is advantageous for demanding metalworking. A potential drawback is higher brittleness compared with rolled variants, so use with appropriate coolant and in a stable clamping setup for best results. The 135° tip angle is chosen to reduce initial cutting forces and to suit harder materials such as stainless steel. Where this tool is most effective and who benefits Workshops, toolrooms and industry professionals who require repeatable, precise holes in metals will find the Twist Drill short Type N especially useful. The design targets applications up to typical diameters and depths encountered in component manufacture, repair and assembly. Its characteristics make it a rational choice for tasks requiring tight tolerances and reliable hole geometry rather than for soft‑wood or masonry applications. For precision metal drilling, choose the MetavCUT Twist Drill short Type N — METAV Werkzeuge offers expert advice and technical support at info@metav-werkzeuge.com or by phone +49 2822 7131930; WhatsApp +49 170 2837271 Twist Drill Brand: MetavCUT SKU: 45061-FDA Diameter: 6.1 mm Total length: 93 mm Spiral length: 57 mm Tip angle: 135° Type: Type N Material: HSS‑G (ground High Speed Steel) Finish/Colour: Bright finished Execution: Short Shank: Fully ground For use in: Drilling Machine (Handheld Drilling Machines not recommended for highest precision) Standard: DIN 338 Model series: Standard Line Manufacturer: MetavCUT Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What materials is the MetavCUT Twist Drill short Type N suitable for? The MetavCUT Twist Drill short Type N is intended primarily for metalworking and performs well in alloyed and unalloyed steel, cast steel, cast iron, sintered iron, malleable iron, non‑ferrous metals and hard plastics thanks to its HSS‑G construction and 135° tip. Is coolant recommended when using the MetavCUT Twist Drill Type N? Using coolant or cutting fluid with the MetavCUT Twist Drill short Type N is recommended for prolonged tool life and improved chip evacuation, especially when drilling harder materials and when aiming for the best surface finish and dimensional stability. For what is a Twist Drill mainly used? A Twist Drill is mainly applied to the machining of high‑strength materials and large hole diameters. Its form allows relatively easy re‑grinding and it endures higher loads, which makes it suitable for tasks requiring robustness and repeatable performance. Which three drill types exist? The three primary drill types are metal drills, wood drills and masonry/concrete drills. Why are Twist Drills re‑pointed? Re‑pointing reduces the cross‑cut at the tip of a Twist Drill. By re‑sharpening the point, friction forces are significantly lowered, which reduces required feed forces and improves centring in the workpiece. Can a metal drill be used to drill wood? A metal drill can be used in wood, but the guidance is worse and the hole finish is less clean. Metal drills are easier to re‑sharpen and exhibit less self‑feeding in soft materials. At which drilling depths is the Twist Drill most commonly used? The Twist Drill is the most used tool for through drilling. For diameters up to around 20 mm and drilling depths up to 100 mm, the Twist Drill is commonly employed. Is HSS or HSSE better? The general belief that HSSE steels are universally superior to HSS is incorrect. When choosing between HSS and HSSE for a MetavCUT Twist Drill Type N, assess whether your working conditions justify the higher cost of HSSE for your specific application.
6.1mm HSS-G Twist Drill DIN 338 ,short, bright finished, Type N - MetavCUT
Twist Drill MetavCUT Profi Line — Type N, 6.1 mm, HSS‑G, Short, 135°, Bright Finished A short MetavCUT Twist Drill Type N for precise metal Drilling Machine work, optimised for hard materials and high stability. Short design for higher stability HSS‑G material for sharp, clean holes 135° tip angle for hard metals Fully ground shaft for superior runout Conforms to DIN 338 for short drills Greater Stability for Accurate Holes Short design reduces the unsupported length of the cutting tool, which directly improves Stability and reduces deflection during machining. The Short 6.1 mm geometry combined with a Fully Ground shaft leads to higher concentricity and cleaner bores when used in a Drilling Machine. As a result, fewer rework operations are required and hole tolerance is easier to maintain. Faster Penetration in Tough Materials Built from HSS‑G, this Short Type N drill achieves up to 40% faster drilling and requires around 50% less feed force compared with conventional HSS drills under comparable conditions. The 135° tip angle is optimised for harder substrates such as stainless steel and tempered alloys, shortening the initial breakthrough time and lowering axial loads on the machine spindle. Precise Application and Recommended Use Designed for metalworking, the Twist Drill Type N excels in drilling Alloyed and Unalloyed Steel, Cast Steel, Cast Iron and Non‑Ferrous Metals. The shortened spiral length limits chatter and makes this drill particularly suited for precise bench, column and stationary machining where coolant can be applied. For manual handfeeding in a Drilling Machine, the improved stability ensures repeatable centre positioning. Manufacturing Quality and Standards for Reliability Produced to DIN 338 as part of the Profi Line, the drill is delivered with a bright finished surface and a ground flute geometry that gives very sharp cutting edges and excellent runout characteristics. Ground flutes (HSS‑G) provide cleaner chips and a defined cutting geometry, though they can be more brittle than rolled variants and therefore benefit from controlled machining parameters and adequate cooling. Strong recommendation: choose the MetavCUT Profi Line short Twist Drill Type N for demanding metal drilling tasks; for advice on suitability, tool parameters or complementary tooling contact METAV Werkzeuge — expert consultation is available by email at info@metav-werkzeuge.com, by phone at +49 2822 7131930 or via WhatsApp at +49 170 2837271 Designation: Twist Drill Brand: MetavCUT SKU: 48061-FDA Diameter: 6.1 mm Spiral Length: 57 mm Overall Length: 93 mm Tip Angle: 135° Type: Type N Execution: Short Shaft Finish: Fully Ground Material: HSS‑G Colour: Bright Finished Model Series: Profi Line Application: Drills for metal Standard: DIN 338 For Drilling Machine: Drilling Machine Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What materials can the MetavCUT Twist Drill Type N be used on? The MetavCUT Twist Drill Type N is primarily specified for metalworking and is suitable for alloyed and unalloyed steel, cast steel, cast iron, sintered iron and non‑ferrous metals; its HSS‑G construction and 135° tip make it particularly effective on harder materials. Is the MetavCUT Twist Drill Type N suitable for handheld drilling? The short configuration and fully ground shaft of the MetavCUT Twist Drill Type N improve stability and centring, so it can be used in hand drilling applications, but best results are achieved with a stationary Drilling Machine and appropriate coolant to avoid undue stress on the tool. For what is a Twist Drill used? A Twist Drill is mainly applied when machining high‑strength materials and larger hole diameters. This form is easy to regrind and withstands higher loads while maintaining good cutting performance. Which 3 drill types exist? The three main drill categories are metal drills, wood drills and masonry/concrete drills. Why are Twist Drills sharpened? Sharpening reduces the cross‑edge at the tip of the Twist Drill, significantly lowering friction and therefore reducing the required feed force; it also improves centring of the tip in the workpiece. Can a metal drill be used in wood? A metal drill can be used in wood, but guidance and finish are usually inferior compared with purpose‑made wood bits; metal drills are easier to regrind and typically have less aggressive self‑feed.
6.25mm HSS Twist Drill DIN 338 ,short, roll forged, black, Type N - MetavCUT
Twist Drill — Type N, 6.25 mm, HSS, short, black, DIN 338 The Twist Drill Type N is a short HSS metal drill designed for stable, precise drilling in steel and other metals using handheld drills or drilling machines. Twist Drill Type N for metal drilling Short HSS design for enhanced stability DIN 338 compliant for short cylindrical drills 118° tip angle for reliable centering Suitable for drilling machines and hand drills Stable performance for demanding metalwork The Twist Drill from MetavCUT combines a short fluted design with HSS material to deliver high rigidity and reduced deflection when drilling into metal. Because the cutter length is reduced relative to standard drills, vibration and runout are minimised, which directly improves hole accuracy and extends tool life. This stability benefits maintenance technicians and workshop professionals who require repeatable centre-to-centre accuracy on metal fabrications. Precise centring and cleaner hole starts A 118° tip angle provides a balanced compromise between initial penetration and centring behaviour, making the drill well suited to typical steels and general metalwork. The geometry lowers the tendency to “walk” on curved or painted surfaces, so fewer pilot holes are needed and setup time is reduced. Users achieve cleaner hole edges and consistent drilling results even when working without elaborate jigs. Standardised dimensions for dependable tooling choices Compliance with DIN 338 ensures the short cylindrical shank and overall geometry match common toolholder and chuck standards, simplifying tool selection and replacement. The HSS designation (High Speed Steel) indicates good toughness and edge retention for standard metal drilling tasks. This combination enables workshops to maintain inventory consistency while choosing a tool that balances cost and performance. Application range and user guidance Engineers, metal fabricators and service technicians will find this Type N drill particularly useful for general-purpose drilling in alloyed and unalloyed steels, cast iron and non-ferrous metals. For best results, select proper cutting speeds and use cutting fluid when drilling steels above moderate hardness; this reduces heat, preserves the cutting edge and improves cycle time. Note that for very soft materials or abrasive masonry, material-specific drills are preferable. Strong recommendation: For precision metal drilling choose the MetavCUT Twist Drill Type N with short HSS design — METAV Werkzeuge offers expert advice and technical support via info@metav-werkzeuge.com, phone +49 2822 7131930 and WhatsApp +49 170 2837271 Designation: Twist Drill Brand: MetavCUT SKU: 400625-FDA Diameter: 6.25 mm Material: HSS (High Speed Steel) Type: Type N Execution: short Colour: black Tip angle: 118° Spiral length: 57 mm Overall length: 101 mm Standard: DIN 338 Application: Drills for metal For drill machine: Drilling Machine Manufacturer: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What is the Twist Drill from MetavCUT used for? The MetavCUT Twist Drill Type N is primarily applied to metalworking tasks; it is intended for drilling into high-strength materials and larger diameters where robust performance is required. Its form allows relatively easy resharpening and it tolerates higher loads during cutting. Which three drill types exist? Commonly distinguished drill types are metal drills, wood drills and stone/concrete drills; the MetavCUT Twist Drill belongs to the metal drill category and is optimised for steel and similar materials. Why are twist drills pointed? Pointing the tip of a twist drill reduces the cross-cutting edge at the tip, which significantly lowers friction and required feed forces; this sharpening also improves centre holding so the drill seats more accurately in the workpiece. Can a Twist Drill be used to drill wood? A metal-oriented Twist Drill such as the MetavCUT Type N can be used in wood, but guidance is reduced and the finish is typically less clean than with a dedicated wood bit; advantages include easier resharpening and less aggressive self-feeding. At what drilling depths are twist drills most commonly used? Twist drills are the standard choice for through-hole drilling; they are most frequently used for diameters up to 20 mm and drilling depths up to about 100 mm, making them suitable for typical workshop operations. What is better, HSS or HSSE? The assumption that HSSE is always superior to HSS is not universally correct; decision-making should consider working conditions and whether the slightly higher investment in HSSE is justified by the specific application.
6.25mm HSS-G Twist Drill DIN 338 ,short, bright finished, Type N - MetavCUT
Die kompakte Kombination aus HSS‑G Material, geschliffenem Schaft und 135° Spitzenwinkel liefert schnelle, präzise Bohrungen in Stahl bei hoher Rundlaufgenauigkeit. Bestellen Sie den Spiralbohrer 6,25 mm von MetavCUT direkt über Metav oder fragen Sie unsere Beratung bei Bedarf an. Spiralbohrer 6,25 mm HSS‑G Kurz (Typ N) — MetavCUT, SKU 450625-FDA Der Spiralbohrer ist ein kurzer, geschliffener HSS‑G Metallbohrer für präzise Bohrungen in legierten und unlegierten Stahl sowie Gusswerkstoffe. Spiralbohrer 6,25 mm HSS‑G, kurz Geschliffener Schaft für hohe Rundlaufgenauigkeit 135° Spitzenwinkel für harte Werkstoffe Spiralänge 63 mm für stabile Spanabfuhr Geeignet für Handbohrmaschine und Stationär Präzision und Effizienz bei harten Werkstoffen Der kurze, geschliffene HSS‑G Kurzbohrer reduziert die Auskraglänge und damit das Verbiegen und Vibrieren während des Bohrens. Dadurch entsteht eine deutlich höhere Stabilität, was besonders bei legierten Stählen und Temperguss wichtig ist. Die geschliffene Geometrie sorgt für sehr scharfe Schneiden und saubere Bohrlöcher, während der 135° Spitzenwinkel das Anbohren in harten Werkstoffen erleichtert und die Anbohrzeit reduziert. Geeignet für Werkstatt und mobile Anwendung Im Standard‑Bereich von 2,0 mm bis 13,0 mm bietet dieser Kurzbohrer ein ausgewogenes Verhältnis aus Handhabung und Leistung. Die Ausführung als Typ N mit normaler Spirale macht ihn prädestiniert für den Einsatz in der Handbohrmaschine ebenso wie in stationären Bohrmaschinen. Bei der Nutzung in mobilen Geräten empfiehlt sich eine stabile Spannaufnahme und moderate Drehzahlen, um die Bruchsicherheit zu erhöhen. Normkonforme Fertigung und Materialeigenschaften Die Herstellung richtet sich nach DIN 338, die kurze Spiralbohrer mit Zylinderschaft normiert. Die Kombination aus HSS‑G und geschliffenem Schaft bedeutet: hohe Schneidleistung und exakte Rundlaufwerte. Geschliffene Bohrer bieten feinste Schneidkanten und enge Toleranzen; sie sind jedoch empfindlicher gegenüber Schockbelastungen, weshalb Kühlung und gleichmäßiger Vorschub empfohlen werden. Anwendungshinweise und arbeitssicherheit Für optimale Ergebnisse wird die Verwendung von Schneidöl oder Kühlmittel empfohlen, besonders beim Bohren in gehärtetem Stahl. Vorbohren ist bei sehr dicken oder zähen Werkstoffen empfehlenswert, um die Querschneide zu entlasten. Die kurze Spiralänge von 63 mm unterstützt die Spanabfuhr bei üblichen Bohrtiefen; bei tiefen Sacklochbohrungen sind abgestufte Aufbohrschritte zu erwägen, um Überhitzung und Spanverwicklung zu vermeiden. MetavCUT empfiehlt diesen HSS‑G Kurzbohrer für präzise Metallbohrungen; bei Fragen zur Einsatzoptimierung erreichen Sie uns per eMail info@metav-werkzeuge.com oder Telefon +49 2822 7131930. Produktmerkmale Artikelnummer: 450625-FDA Marke: MetavCUT Serie: Standard Line Bezeichnung: Spiralbohrer Typ: Typ N Fakten Durchmesser: 6,25 mm Gesamtlänge: 101 mm Spirallänge: 63 mm Spitzenwinkel: 135° Verpackungseinheit: 10 Besonderheiten Material: HSS-G (Schnellarbeitsstahl, geschliffen) Schaft Ausführung: geschliffen (vollständig geschliffener Zylinderschaft) Norm: DIN 338 (kurze Spiralbohrer mit Zylinderschaft) Farbe: blank Für Bohrmaschine: Handbohrmaschine FAQ Für welche Materialien eignet sich der Bohrer am besten? Der Kurzbohrer von MetavCUT (Spiralbohrer 6,25 mm, Typ N, SKU 450625-FDA) eignet sich besonders für legierte und unlegierte Stähle, Gusseisen sowie Nichteisenmetalle und Hartkunststoffe aufgrund des HSS‑G Werkstoffs und des 135° Spitzenwinkels. Kann der Bohrer in einer Handbohrmaschine verwendet werden? Ja, die Ausführung ist für die Nutzung in der Handbohrmaschine geeignet; dennoch ist auf eine feste Spannaufnahme und moderate Drehzahl zu achten, damit der geschliffene Bohrer nicht durch seitliche Kräfte beschädigt wird. Warum ist geschliffener HSS besser für Metallbohrungen? Geschliffene HSS‑Bohrer bieten sehr scharfe Schneidkanten und hohe Rundlaufgenauigkeit, was saubere Bohrlöcher erzeugt. Beim Spiralbohrer MetavCUT bedeutet das bessere Oberflächenqualität, allerdings erhöhte Empfindlichkeit gegen Stoßbelastungen. Ist Kühlung beim Bohren mit diesem Bohrer erforderlich? Bei harten oder dicken Werkstoffen wird Kühlung oder Schneidöl empfohlen, um Überhitzung zu vermeiden und die Standzeit des HSS‑G Bohrers zu verlängern. Dies gilt insbesondere bei stationärem Einsatz und höheren Vorschubkräften. Benötigt man Vorbohren für größere Bohrtiefen? Bei tiefen Bohrungen oder zähen Werkstoffen empfiehlt sich Vorbohren oder mehrstufiges Aufbohren zur Entlastung der Querschneide; der Kurzbohrer ist für typische Anwendungen im Standard‑Bereich konzipiert.
6.2mm HSS Twist Drill DIN 338 ,short, roll forged, black, Type N - MetavCUT
Twist Drill — Type N short HSS, Ø 6.2 mm, 118°, black, DIN 338, MetavCUT The Twist Drill Type N short HSS is a precision metalworking drill with a 6.2 mm diameter, a 118° tip angle and a compact design for stable, accurate holes in metal. Short HSS design for improved stability DIN 338 compliant short twist drill 6.2 mm diameter for precise metal holes 118° tip for controlled entry Suitable for drilling machines and hand drills Stable drilling for accurate metal holes The short HSS construction reduces overhang and vibration, delivering higher stability and more precise results when machining metal. Because the flute length is reduced, the tool resists bending and provides consistent concentricity in through-holes. This results in cleaner bores and less rework when working on components that demand tight tolerances. Material and geometry explained for reliable results Made from High Speed Steel (HSS), the drill combines toughness with wear resistance ideal for common metalworking tasks. The 118° tip angle eases centring on curved or softer surfaces and lowers the initial cutting forces; this geometry is particularly effective for general metal grades and reduces the chance of walking at the start of the hole. Short drills per DIN 338 are optimised for rigid setups and stationary or portable drilling machines. Where this drill excels and who benefits Designed primarily as a Drills for Metal tool, the Type N short configuration suits workshops, toolrooms and maintenance pros seeking repeatable performance in steel, cast iron, non-ferrous metals and plastics. The compact format is beneficial for confined setups or when using hand-held drilling devices, delivering greater control and faster, more reliable hole-making for production and repair tasks. Choose the MetavCUT Twist Drill Type N short HSS for dependable metal drilling — for personalised technical advice and application support contact METAV Werkzeuge: info@metav-werkzeuge.com · Phone: +49 2822 7131930 · WhatsApp: +49 170 2837271 Designation: Twist Drill Brand: MetavCUT SKU: 40062-FDA Diameter: 6.2 mm Spiral length: 57 mm Overall length: 101 mm Tip angle: 118° Type: Type N Execution: short Material: HSS Colour: black Suitable for: Drilling Machine (Hand Drill) Application: Drills for Metal Standard: DIN 338 Manufacturer: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What is the Twist Drill Type N by MetavCUT used for? The MetavCUT Twist Drill Type N is primarily used for machining metal; it is particularly suitable for drilling in alloyed and unalloyed steel, cast iron, non-ferrous metals and certain plastics. Its short HSS design makes it robust for demanding tasks and larger drill diameters where stability and precision are required. Which three drill types are commonly available? Common drill categories are metal drills, wood drills and stone/masonry drills. The MetavCUT Twist Drill Type N falls into the metal drills group and is tailored to metalworking applications.
6.2mm HSS-E Twist Drill DIN 338 ,short, 5% cobalt-alloyed, Type N - MetavCUT
Twist Drill (Type N) — 6.2 mm, 135° tip, short HSS‑E, 5% cobalt‑alloyed, DIN 338 — MetavCUT A Twist Drill (Type N) designed for precise metal drilling, combining a 6.2 mm diameter and a 135° tip angle in a short, stable execution suitable for demanding machining tasks. Type N Twist Drill, 6.2 mm diameter 135° tip angle for hard materials Short execution for higher stability HSS‑E with 5% cobalt for improved toughness Fully ground shank, DIN 338 compliant Exceptional stability and precision for metalworking Short-form drills deliver measurable advantages when precision matters. The short design of this MetavCUT Twist Drill reduces the unsupported overhang, which increases stability and lowers the tendency to wander or bend under load. Combined with the 135° tip angle, the geometry shortens pilot time and improves centring in harder materials. For production environments that require repeatable hole quality, the shorter spiral length also reduces vibration and contributes to more consistent hole diameter and surface finish. Material composition for longer life under stress Constructed from HSS‑E and alloyed with 5% cobalt, this short Twist Drill offers higher hot hardness and greater wear resistance than standard HSS. The cobalt content increases toughness at elevated temperatures, making the tool more suitable for drilling alloyed and unalloyed steel, cast iron, non‑ferrous metals and certain plastics. The fully ground flute geometry provides very sharp cutting edges and high running accuracy; however, grinding can increase brittleness, so coolant use and stable clamping are recommended to maximise tool life. Designed for drilling machines and demanding applications Classified to DIN 338, this Type N drill is the classical metal drill geometry optimised for machining of metallic workpieces on drilling machines. The shorter overall length and fully ground spiral make it particularly suited to stationary machines and operations that require high precision rather than freehand drilling. Typical applications include workshop fabrication, maintenance, toolmaking and any task where controlled drilling into Steel and similar materials is required. Note that Type N is not optimised for very soft materials where specialised geometries perform better. Practical advice for safe and efficient use When using the MetavCUT Twist Drill, ensure secure clamping and appropriate coolant or cutting fluid to dissipate heat and extend tool life. Start with a light feed to establish the hole, especially in harder materials, and avoid excessive spindle speeds that can overheat the tip. The 135° point reduces entry forces and improves centring for harder alloys, while the short execution minimises deflection—both contributing to cleaner, more accurate holes. For portable handheld drilling machines, consider the shorter projection to reduce user fatigue and increase control. The MetavCUT short Twist Drill (Type N) is recommended for professionals seeking stable, precise metal drilling; for expert technical advice or to confirm suitability for specific tasks contact METAV Werkzeuge — Email: info@metav-werkzeuge.com • Phone: +49 2822 7131930 • WhatsApp: +49 170 2837271 Twist Drill Brand: MetavCUT SKU: 47062-FDA Diameter: 6.2 mm Overall length: 101 mm Spiral length: 63 mm Tip angle: 135° Type: Type N Execution: short Material: HSS‑E Colour: 5% cobalt‑alloyed Shank design: fully ground Series: Standard Line Standard: DIN 338 For drilling machine: Drilling Machine Application: Drills for metal Manufacturer: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What is the MetavCUT Twist Drill (Type N) mainly used for? The MetavCUT Twist Drill (Type N) is primarily applied for machining high‑strength materials and larger bore diameters. Its short form suits precise work and makes the drill easier to re‑grind while maintaining resistance to higher loads in metalworking operations. Which three drill types exist? There are three common drill types: metal drills, wood drills and stone/concrete drills. The MetavCUT Twist Drill (Type N) belongs to the metal drill category, optimised for use in metalworking environments. Why are Twist Drills pointed? The point geometry reduces the cross‑cut at the tip of a Twist Drill, which lowers friction and thus requires smaller feed forces. By sharpening the tip, the drill centres more reliably in the workpiece and cuts with less resistance, improving entry behaviour and hole quality. Can you use a Twist Drill to drill wood? A metal drill such as the MetavCUT Twist Drill (Type N) can be used in wood, but guidance and centring are generally poorer and the finish may be less clean compared with purpose‑made wood bits. Metal drills are easier to re‑grind and show less self‑feed, which can be an advantage in some hobby or repair scenarios. For which drilling depths is the Twist Drill most commonly used? A through hole in a solid piece is typically executed with a Twist Drill. For diameters up to 20 mm and drilling depths up to 100 mm, the Twist Drill is the most frequently used tool. The MetavCUT Twist Drill (Type N) is therefore appropriate for many standard metal drilling tasks. What is better, HSS or HSSE? The common assumption that HSSE steels are always superior to standard HSS is not universally correct. Choose between HSS and HSSE based on actual working conditions and whether the higher purchase cost of HSSE is justified by the specific performance benefits required.
6.2mm HSS-G Body Drill ,double sided, bright finished - MetavCUT
Der geschliffene Karosseriebohrer kombiniert Präzision und Alltagstauglichkeit: Die HSS‑G‑Geometrie ermöglicht bis zu 40 % schnelleres Bohren bei deutlich geringerer Anpresskraft, die doppelseitige Ausführung verlängert die Nutzungsdauer durch Umkehrbarkeit, und der 135° Spitzenwinkel sorgt für saubere Ansätze in härteren Werkstoffen. Nutzen Sie diese Kombination aus Effizienz, Stabilität und hoher Rundlaufgenauigkeit und beziehen Sie den Bohrer direkt über Metav oder klären Sie Details telefonisch oder per E‑Mail. Karosseriebohrer »58062-FDA« von MetavCUT (HSS‑G, 6,2 mm) Der Karosseriebohrer ist ein doppelseitig ausgeführter HSS‑G‑Bohrer, konzipiert für präzise Metallbohrungen in Werkstatt und Karosseriebau Karosseriebohrer »58062-FDA« von MetavCUT Geschliffenes HSS‑G für präzise Metallbohrungen Doppelendbohrer: beidseitig einsetzbar 6,2 mm Durchmesser, Spirallänge 16 mm 135° Spitzenwinkel für härtere Werkstoffe Effiziente Leichtarbeit dank geschliffener HSS‑Geometrie Die geschliffene HSS‑G‑Geometrie reduziert die Anbohrkräfte deutlich und ermöglicht ein bis zu 40 % schnelleres Bohren gegenüber herkömmlichen HSS‑Bohrern. Für Anwender bedeutet das weniger Ermüdung bei wiederkehrenden Bohrvorgängen und eine höhere Produktivität in der Werkstatt. Außerdem führt der CNC‑Schliff zu sehr scharfen Schneiden und hoher Rundlaufgenauigkeit, was saubere Bohrlöcher in legierten und unlegierten Stählen, Gusswerkstoffen sowie Hartkunststoffen fördert. Doppelseitige Bauform für geringere Stillstandszeiten Die doppelseitige Ausführung macht den Bohrer besonders wirtschaftlich: Ist eine Spitze stumpf, kann der Bohrer einfach gewendet werden, so dass ein zweites Schneidenpaar sofort verfügbar ist. Die kompakte, stabile Bauform eignet sich speziell für Niet‑ und Dünnblecharbeiten in der Karosseriebranche und reduziert den Bedarf an Ersatzbohrern. Aufgrund der geschliffenen Fertigung sollte bei stationärer Nutzung eine angemessene Kühlung eingesetzt werden, um Bruchrisiken zu minimieren. Praxisgerechte Einsatzempfehlungen und Zielgruppe Mit 6,2 mm Durchmesser gehört der Bohrer zum Standard‑Bereich und ist ideal für Werkstätten, Karosseriebau und montageorientierte Anwender sowie für viele Heimwerkerprojekte. Für besonders präzise Anwendungen empfiehlt sich Vorzentrieren mit einem Zentrierbohrer, um Wandern beim Anbohren zu vermeiden. Die Kombination aus 135° Spitzenwinkel und geschliffener Schaftausführung sorgt für saubere Ansätze, besonders beim Bohren in härtere Materialien; bei zähen Werkstoffen Kühlung und moderater Vorschub verwenden. Empfehlung: Setzen Sie auf die MetavCUT Standard Line für langlebige, präzise Blecharbeiten und ordern Sie den Karosseriebohrer direkt über Metav per E‑Mail info@metav-werkzeuge.com oder Telefon +49 2822 7131930. Produktmerkmale Artikelnummer: 58062-FDA Marke: MetavCUT Bezeichnung: Karosseriebohrer Serie: Standard Line Verpackungseinheit: 10 Anwendung: Bohrer für Metall Ausführung: doppelseitig Fakten Durchmesser: 6,2 mm Gesamtlänge: 66 mm Spirallänge: 16 mm Spitzenwinkel: 135° Besonderheiten Material: HSS-G Schaftausführung: geschliffen Farbe: blank Für Bohrmaschine: Handbohrmaschine Verpackungseinheit: 10 Hinweis: G = geschliffen – scharfe Kanten, hohe Rundlaufgenauigkeit FAQ Für welche Materialien eignet sich der Bohrer am besten? Der MetavCUT Karosseriebohrer Standard Line (SKU 58062‑FDA) eignet sich besonders für legierten und unlegierten Stahl, Gussstahl, Gusseisen, Sintereisen, Temperguss, Nichteisenmetalle sowie Hartkunststoff und liefert in diesen Werkstoffen saubere Bohrbilder. Kann der Bohrer mit einem Akku‑Bohrer verwendet werden? Ja, der Karosseriebohrer ist für den Einsatz mit handgeführten Bohrmaschinen geeignet; bei 6,2 mm Durchmesser empfiehlt sich jedoch vorheriges Zentrieren für sehr präzise Passungen, um Wandern beim Anbohren zu vermeiden. Was bedeutet doppelseitig konkret in der Praxis? Doppelseitig heißt, dass der Bohrer an beiden Enden eine Schneide besitzt; dies erlaubt einfaches Wenden im Schadensfall und reduziert Stillstandszeiten, was besonders bei Niet‑ und Dünnblecharbeiten vorteilhaft ist. Wie lässt sich die Bruchgefahr bei geschliffenen HSS‑Bohrern minimieren? Um Bruchrisiken zu reduzieren, sollte der geschliffene HSS‑G‑Bohrer mit moderatem Vorschub, geeigneter Drehzahl und, bei zähen Werkstoffen, mit Kühlung betrieben werden; stationäre Befestigung oder stabile Führung erhöht die Lebensdauer deutlich.
6.2mm HSS-G Twist Drill DIN 338 ,short, bright finished, Type N - MetavCUT
Twist Drill (Type N) — Short HSS‑G Drill, 6.2 mm, 135° Point, Bright Finished, Fully Ground, DIN 338 — MetavCUT The Twist Drill (Type N) is a short HSS‑G drill designed for precise metalworking tasks on drilling machines and hand drills, optimised for hard materials and stable, accurate hole creation. Short design for higher stability 6.2 mm diameter for precise holes 135° point angle for hard materials Fully ground HSS‑G for sharp, accurate cuts Conforms to DIN 338 for industrial compatibility High performance for demanding metal drilling Built to deliver measurable productivity, this Twist Drill in HSS‑G quality combines a short overall length with a fully ground geometry to reduce vibration and improve centring. The 135° Point Angle eases penetration into harder metals such as stainless steel, while the CNC grinding of the flutes yields very sharp cutting edges and excellent runout accuracy. As a result, users experience up to 40% faster drilling and require 50% less feed force compared with conventional HSS variants, making this tool a rational choice where efficiency and repeatability matter. Short geometry that increases stability and precision A shorter projection from the chuck significantly reduces lever forces and deflection during drilling. The short design is therefore particularly suitable for operations where tight tolerances and straight, burr‑reduced holes are required. Because the flutes and cutting lips are produced by grinding rather than rolling, the drill achieves a cleaner hole surface and better dimensional consistency, especially when used with appropriate coolant and stationary or well‑supported setups. Material and cutting geometry explained for every user The HSS‑G (ground high speed steel) construction provides a balance of hardness and toughness for machining a wide range of metals. The designation Type N denotes the classic normal helix geometry tailored for metalworking; it is not optimised for soft timbers. Compliance with DIN 338 ensures standardised dimensions and shank form for easy mounting in chucks and toolholders. For less experienced users: a larger point angle reduces the tendency to wander on tough surfaces and shortens the time to break through the material. Where this drill delivers the most value This short Twist Drill is aimed at professional workshops and maintenance teams that work with alloyed and unalloyed steels, cast materials, non‑ferrous metals and hard plastics. It excels in jobs on bench drills and machine tools where stiffness is available and precise hole geometry is required. If the work involves deep, flexible setups or timber, consider dedicated long‑form or wood drills instead to match the application. MetavCUT recommends this Type N short HSS‑G Twist Drill for precision metalwork — for technical advice or to check suitability for a specific task, contact METAV Werkzeuge: info@metav-werkzeuge.com • Phone +49 2822 7131930 • WhatsApp +49 170 2837271 Technical Information Designation: Twist Drill (Short) Brand: MetavCUT SKU: 45062-FDA Diameter: 6.2 mm Point Angle: 135° Type: Type N Material: HSS‑G (ground high speed steel) Finish/Colour: Bright Finished Shank Execution: Fully Ground Overall Length: 101 mm Spiral Length: 63 mm Application: Drills for Metal / Drilling Machine / Hand Drill use Norm: DIN 338 Execution: Short Model Series: Standard Line Shaft Treatment: Geschliffen (ground) Manufacturer: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What is a Twist Drill used for and which materials suit the MetavCUT Type N short drill? The MetavCUT Twist Drill Type N is primarily used for drilling metal; it is well suited to alloyed and unalloyed steels, cast materials, non‑ferrous metals and hard plastics, offering reliable centring and clean hole walls when used on drilling machines or supported hand drills. Why choose a short Twist Drill like the MetavCUT Type N for precision work? A short Twist Drill reduces overhang and bending, improving stability and rotational accuracy; the ground geometry of the MetavCUT Type N gives sharp cutting edges that help achieve precise diameters and reduce burr formation. For what is a Twist Drill mainly used? A Twist Drill is primarily applied in the machining of high‑strength materials and for larger hole diameters; its ground form is easy to sharpen and withstands greater loads, making it suitable for difficult metalworking tasks. Which three drill types exist? There are three main drill categories: Metal drills, Wood drills, Stone/Concrete drills. Why are Twist Drills points de‑pointed (split)? Splitting the point reduces the cross‑edge at the tip, lowering friction and therefore the required feed force; it also improves centring of the tip in the workpiece. Can a metal Twist Drill be used to drill wood? A metal drill can be used in wood, but guidance is poorer and hole finish is less clean; metal drills are easier to resharpen and have a lower self‑feed tendency compared with dedicated wood drills. At which drilling depths is the Twist Drill most commonly used? Twist Drills are typically used for through‑hole drilling; for diameters up to 20 mm and depths up to 100 mm, the Twist Drill remains the most commonly employed tool. Is HSS or HSSE better? The general assumption that HSSE is categorically superior to HSS is not universally correct; when choosing, evaluate whether the working conditions justify the higher cost of HSSE for your specific application.
6.2mm HSS-G Twist Drill DIN 338 ,short, bright finished, Type N - MetavCUT
Twist Drill — short HSS‑G Metal Drill, 6.2 mm, 135°, Type N, Bright Finished A short Twist Drill (Type N) designed for precision metalworking and use in drilling machines, offering high stability and fast cutting performance Short design for greater stability and precision HSS‑G material for sharp, durable cutting edges 135° tip angle for harder materials and faster entry Fully ground shank for excellent runout accuracy Precision and Stability for Demanding Metalwork Shorter overall length and a reduced overhang provide significantly higher stability during cutting operations. The combination of a short geometry and a fully ground shank minimises vibration and deflection, so holes remain concentric and tolerances are easier to hold. This design is especially advantageous when machining hard materials or when using smaller diameters, because the stiffer setup reduces the risk of chatter and improves hole quality. Faster Cutting with Lower Feed Force Thanks to the HSS‑G grind and optimized geometry, this drill achieves up to 40% faster drilling rates while requiring around 50% less feed force than conventional HSS tools. The 135° tip angle shortens penetration time in tough alloys and stainless steels by reducing the initial cutting resistance. For users this means quicker cycle times and reduced operator effort, particularly on demanding jobs where efficiency and repeatability matter. Engineered for Metalworking and Machine Use Designed to meet DIN 338, this short twist drill is tailored for metal applications including alloyed and unalloyed steel, cast steels, cast iron, sintered iron, non‑ferrous metals and hard plastics. The Type N normal spiral makes it a versatile choice for conventional metal drilling. Because ground drills can be more brittle than roll‑formed types, it is recommended to use adequate cooling and, where possible, a machine setup rather than hand‑only operation to maximise tool life and prevent breakage. Practical Advice for Safe and Accurate Results When setting up, ensure the drill is clamped securely in a high‑precision chuck and that the workpiece is firmly supported to avoid movement. Start with a suitable pilot or centre drill where needed, and adapt cutting speeds to the material and drill diameter. Regular sharpening of the cutting lips maintains centring behaviour and hole finish; ground HSS tools deliver excellent runout accuracy but benefit from controlled feed and coolant during deep or interrupted cuts. Strong recommendation: choose the MetavCUT Profi Line short Twist Drill for precise, efficient metal drilling — for technical advice or to confirm suitability for your application contact METAV Werkzeuge; we provide expert consultation and comprehensive support. 📧 info@metav-werkzeuge.com ☎️ +49 2822 7131930 ✔️ WhatsApp: +49 170 2837271 Twist Drill Brand: MetavCUT SKU: 48062-FDA Diameter: 6.2 mm Overall length: 93 mm Spiral length: 57 mm Tip angle: 135° Type: Type N Length execution: Short Shank execution: Fully ground Material: HSS-G Standard: DIN 338 Colour: Bright finished For drilling machine: Drilling Machine Application: Drills for metal Model series: Profi Line Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What is a Twist Drill used for? A Twist Drill is primarily used for machining high‑strength materials and larger diameters; it is especially applied to metalworking where robust performance is required. The design is easy to regrind and withstands higher loads, making it a common choice for drilling steels and tougher alloys. Which three drill types are there? The basic categories are Metal drills, Wood drills, and Stone/Concrete drills. Each type features geometry and flutes adapted to its target material to ensure effective chip evacuation and hole quality. Can this Twist Drill be used in hand drills or only in machines? The MetavCUT Profi Line short Twist Drill is optimised for machine use to exploit its stability and precision, but it can be used in a quality handheld drilling machine for light tasks. For heavy or deep drilling in hard materials, a stationary drilling machine and coolant are recommended to avoid excessive stress on the tool. Why are twist drills point‑ground? Point grinding reduces the cross‑edge at the tip, significantly lowering friction so less feed force is required. A ground point also improves centring in the workpiece, leading to more accurate hole positions and smoother drilling starts.
6.3mm Centre Drill DIN 333 Form B With Countersink 60/120° Right-Hand HSS - TECWERK
Combining HSS construction, DIN 333 Form B geometry and an integrated protective countersink, this centre drill delivers repeatable, accurate pilot bores and secure countersinking for serial metalworking. Order the TECWERK centre drill via Metav Werkzeuge or consult our specialists for technical guidance. TECWERK centre drill DIN 333 Form B, Ø6.3 mm, HSS with protective countersink A TECWERK centre drill engineered for accurate centring and combined countersinking in typical metalworking and machining workflows. HSS for extended tool life DIN 333 Form B geometry Integrated protective countersink Right‑hand cutting action Precise geometry that reduces rework and scrap The DIN 333 Form B design ensures a consistent pilot bore and stable seating for subsequent drilling or turning operations. The Form B geometry combines a short, rigid pilot with a refined countersink profile, which reduces radial runout and minimises burr formation. For production environments where part quality and repeatability matter, this geometry decreases the need for secondary finishing and cuts overall cycle time. The constructive benefit is especially apparent when producing centre holes that serve as references in later machining stages. Robust HSS construction for continuous use Manufactured from high‑speed steel (HSS), the tool balances toughness and wear resistance for general workshop and industrial use. HSS maintains cutting-edge hardness at elevated temperatures, which means longer intervals between tool changes compared with standard carbon steels. The Ø6.3 mm main diameter and 20 mm shank provide a stable hold in conventional chucks or collets, supporting straightness under load and reducing chatter. This robustness translates into fewer interruptions on the shop floor and a more predictable production rhythm. Integrated protective countersink for safer setup The version with protective countersink combines centring and a guarded countersink in one tool, reducing tool changes and alignment errors. The dual‑angle countersink (60/120°) offers reliable seating for centre holes and helps protect the workpiece surface during initial engagement. Right‑hand cutting action complements standard spindle rotation and ensures conventional chip evacuation. In practice, the integrated countersink lowers setup complexity and minimises the risk of damaging delicate workpiece faces during pilot drilling. Measurable feed and handling data for efficient programming For programmable and manual machine operation, the tool’s recommended feed in steel (up to 800 N) is 0.05 mm/rev, a conservative value that balances surface quality and tool life. The 80 mm overall length offers accessibility for through‑work and shallow recesses while keeping overhang low to preserve rigidity. These measurable parameters assist process planners in standardising cycle times and calculating throughput for repetitive tasks. Clear numeric data supports rapid CAM setup and consistent results across batches. Choose TECWERK centre drills for dependable centring accuracy and simplified set‑ups — contact Metav Werkzeuge for tailored advice or to request order details via info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: 2000861636NW SKU: 2000861636NW Product type: Centre drill Brand: TECWERK Form: B Standard: DIN 333 Measurements Diameter: 6.30 mm Overall length: 80 mm Shank diameter: 20 mm Countersink angle: 60/120° Feed in steel ≤ 800 N: 0.05 mm/rev Special features Material: HSS Execution: with protective countersink Cutting direction: right‑hand cutting Packaging unit: 1 FAQ What materials can this centre drill process? The TECWERK centre drill is made from HSS and is intended for general metalworking; it is suitable for common steels and general workshop materials where HSS performance is appropriate. Is the countersink angle suitable for standard centre holes? Yes. The integrated countersink offers 60/120° geometry, designed to produce reliable seating for centre holes in accordance with common machining practices. How should the tool be held in the machine? Use a secure chuck or collet matching the 20 mm shank to maintain rigidity and reduce runout during pilot drilling. What feed rate is recommended for steel workpieces? For steel up to 800 N, a feed of 0.05 mm/rev is recommended to balance finish and tool life when using this centre drill. Can this tool be used in automated production with consistent results? Yes. The DIN 333 Form B geometry and HSS construction support repeatable centring and countersinking, making the tool suitable for standardised production environments. Manufacturer/Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund
6.3mm HSS Twist Drill DIN 338 ,short, roll forged, black, Type N - MetavCUT
Twist Drill — Type N, Ø 6.3 mm, 118° point angle, short HSS, black, DIN 338 — MetavCUT The Twist Drill Type N is a short HSS metal-drilling bit designed for use in hand and drilling machines, offering precise, stable performance for metalworking tasks. Short HSS design for increased stability Conforms to DIN 338 for short twist drills 118° point angle for reliable centring on common metals Suitable for alloyed and unalloyed steel and non-ferrous metals Black finish reduces glare and aids chip evacuation Precision and durability for metalworking professionals The short HSS construction of this Twist Drill provides enhanced stability and reduced deflection during machining, making it ideal for accurate holemaking. Manufactured to DIN 338 specifications, the reduced projection length minimises chatter and improves concentricity when drilling in steel and cast iron. This results in consistently round holes and longer tool life compared with longer, more flexible bits. Versatile tip geometry that aids centring and feed Equipped with a 118° point angle, this Type N bit balances entry behaviour and cutting forces for general-purpose metal drilling. The geometry supports easier centring on slightly curved or irregular surfaces and is effective across a range of common metals. For users seeking a classic “Normal Spiral” performance, this bit provides a dependable compromise between fast penetration and controlled cutting action. Practical advantages for workshop and maintenance tasks This short Twist Drill excels in workshop and maintenance environments where accessibility and rigidity matter. The compact overall length reduces the exposed shank, lowering the risk of bend or breakage under side loads. For repetitive repair or assembly work on machinery and metal components, the improved stiffness translates into fewer broken bits and a more predictable drilling process. Material suitability and manufacturing benefits explained Made from High Speed Steel (HSS), the bit is suitable for alloyed and unalloyed steel, cast iron, non-ferrous metals and many plastics. HSS offers a favourable combination of hardness and toughness; roll-formed HSS variants reduce the risk of breakage for small-diameter drills and maintain edge integrity during standard metalworking operations. The Type N normal spiral is the classic choice for metal drilling and can be resharpened when necessary to extend service life. Strong recommendation: Choose the MetavCUT Twist Drill Type N for reliable, precise metal drilling; for personalised advice or technical data METAV Werkzeuge provides expert support — eMail: info@metav-werkzeuge.com | Phone: +49 2822 7131930 | WhatsApp: +49 170 2837271 Technical data Designation: Twist Drill Brand: MetavCUT SKU: 40063-FDA Diameter: 6.3 mm Spiral Length: 63 mm Overall Length: 101 mm Point Angle: 118° For Drill: Drilling Machine / Hand Drill Type: Type N Material: HSS (High Speed Steel) Execution: short Colour: black Application: Drills for metal Standard: DIN 338 Manufacturer: MetavCUT Manufacturer: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What materials can the MetavCUT Twist Drill Type N be used on? The MetavCUT Twist Drill Type N, made of HSS, is intended primarily for metalworking and is suitable for alloyed and unalloyed Steel, Cast Iron, Non‑Ferrous Metals and various Plastics; this composition provides a balance between hardness and toughness for common workshop tasks. What is a Twist Drill used for? A Twist Drill, such as the MetavCUT Twist Drill Type N, is mainly applied to the machining of high‑strength materials and larger drill diameters; its form allows straightforward resharpening and it withstands higher loads during drilling. Which 3 drill types are there? The three main drill categories are Metal Drills, Wood Drills and Masonry/Concrete Drills.
6.3mm HSS-E Twist Drill DIN 338 ,short, 5% cobalt-alloyed, Type N - MetavCUT
Twist Drill (Type N) — 6.3 mm, 135° Tip, Short, 5% Cobalt‑Alloyed, HSS‑E, DIN 338 The Twist Drill Type N is a short HSS‑E drill designed for precise metal drilling with hand and drilling machines, offering high stability and wear resistance in demanding machining tasks. Short design for improved stability and precision 5% Cobalt‑alloyed HSS‑E for increased heat resistance 135° Tip angle for harder materials and stainless steel Fully ground shank for excellent runout accuracy Conforms to DIN 338 for standardised short twist drills Exceptional Stability and Accurate Hole Making for Metalworking Short Spiral Geometry delivers a measurable benefit in everyday machining: the reduced overhang increases Stability and cuts down on bit deflection, so holes come out truer to size. This Short Twist Drill with a 63 mm Spiral Length and 101 mm Overall Length is particularly suited to operations where rigidity matters, such as drilling in steel or when using a Hand Drilling Machine. The 135° Tip shortens initial entry time in harder materials and helps maintain centring under load. Enhanced Material Properties for Longer Life under Heat and Load Manufactured from HSS‑E with 5% Cobalt, this Twist Drill offers greater red hardness and wear resistance compared with conventional HSS. The cobalt‑alloyed composition means the tool tolerates higher cutting temperatures and preserves cutting edges longer when machining alloyed and unalloyed steel, cast iron and non‑ferrous metals. HSS‑E (High Speed Steel with Cobalt) describes a faster heat‑resistant steel grade that balances toughness with hardness, reducing the need for frequent tool changes. Precision Grinding and Standard Compliance for Reliable Results The fully ground flute geometry produces very sharp cutting edges and high concentricity, yielding clean, accurate bores in metal. As defined by DIN 338, this Short Twist Drill is produced to standardised dimensions and tolerances for short drills with cylindrical shanks. Ground tools typically give better hole quality than roll‑formed alternatives; they are easier to resharpen but require proper cooling and appropriate speeds to avoid premature breakage. Optimised for Metal Applications and Practical Use Recommendations Designed as a classic Type N normal‑spiral metal drill, this tool is recommended for a range of metalworking tasks on both stationary and portable drilling equipment. The shorter cutting length reduces the risk of bending and is therefore ideal for precision holes and tougher materials. For best results, use suitable cutting speeds, adequate lubrication or coolant when drilling stainless or hardened steels, and secure the workpiece to minimise vibration. The construction allows for easier regrinding when required, extending service life. Strong recommendation: Choose the MetavCUT HSS‑E short Twist Drill for precise, high‑duty metal drilling — for personalised technical advice and application support contact METAV Werkzeuge; eMail: info@metav-werkzeuge.com ☎️ +49 2822 7131930 ✔️ WhatsApp +49 170 2837271 Designation: Twist Drill Brand: MetavCUT SKU: 47063-FDA Type: Type N Diameter: 6.3 mm Overall length: 101 mm Spiral length: 63 mm Point angle: 135° Material: HSS‑E Cobalt content: 5% cobalt‑alloyed Execution: Short Shank finish: Fully ground Conforms to: DIN 338 Application: Drills for metal Suitable for: Drilling Machine (Hand Drilling Machine) Model series: Standard Line Manufacturer: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What is the best use for the MetavCUT Twist Drill Type N? The MetavCUT Twist Drill Type N is primarily used for machining high‑strength materials and larger drill diameters; its short design and HSS‑E composition make it easier to resharpen and capable of withstanding higher loads during metalworking. Which three drill types are commonly distinguished? In general practice the main categories are Metal drills, Wood drills and Stone/Concrete drills; the MetavCUT Twist Drill belongs to the metal drill category and is optimised for steel and similar materials. Why are Twist Drills sharpened at the point? The point sharpening reduces the cross‑cut at the tip of the Twist Drill, lowering friction and therefore the required feed forces; additionally, a properly sharpened tip improves centring in the workpiece. Can a metal Twist Drill be used to drill wood? A metal drill such as the MetavCUT Twist Drill can be used in wood, but guidance and finish are typically inferior compared with dedicated wood drills; metal drills are easier to resharpen and exhibit less self‑feeding in soft materials. For which drilling depths is the Twist Drill most commonly used? A through hole in solid material is often executed with a Twist Drill; for diameters up to about 20 mm and drilling depths up to approximately 100 mm the Twist Drill is the most frequently used tool.
6.3mm HSS-G Twist Drill DIN 338 ,short, bright finished, Type N - MetavCUT
Twist Drill — Type N short, Ø 6.3 mm, 135° point, Bright finished, Fully ground, DIN 338, HSS‑G by MetavCUT The Twist Drill Type N short is a precision metal‑drilling bit with a 6.3 mm diameter and a 135° point angle, designed for stable, high‑accuracy work in hand drills and drilling machines. Short Type N Twist Drill for high stability Ø 6.3 mm HSS‑G fully ground cutting geometry 135° point angle for hard metals like stainless steel Fully ground shank ensures high concentricity Conforms to DIN 338 for metal drilling Reliable stability and precision for demanding metal jobs The short design of this Twist Drill delivers increased Stability and reduced deflection during drilling, which is particularly valuable when working with hard or thick metals. Because the Out‑of‑chuck length is shorter than standard bits, vibration is minimised and the tool gives a more concentric hole. This construction makes the bit especially suitable for precise setups on a drill press or for accurate handheld operations where hole quality matters. The fully ground geometry ensures sharp cutting edges and consistent hole diameters. Faster penetration and lower feed forces in hard materials A 135° Point Angle reduces the tendency to wander and shortens the initial penetration phase on tough substrates. Combined with the HSS‑G (ground high‑speed steel) material, the bit requires noticeably less feed force, improving operator comfort and control. These features support efficient machining in alloyed and unalloyed steel, cast steel, grey iron, sintered iron and many non‑ferrous metals, enabling cleaner holes and longer tool engagement before loss of edge. Suited applications and who benefits most This Type N short Twist Drill is designed for professional metalworkers, toolroom staff and maintenance technicians who need reproducible, high‑quality holes in metals. It works well in both stationary drilling machines and robust hand drills for repair, assembly and fabrication tasks. The drill is optimised for metalworking scenarios rather than soft timber or masonry, offering a reliable choice where precision and repeatability are priorities. Material, manufacturing and care for longer tool life Being HSS‑G means the flute geometry and cutting edges are produced by CNC grinding rather than rolling, giving sharper edges and superior roundness, though with slightly higher brittleness. For best results use cutting fluid or coolant when machining steels, and avoid heavy interrupted cuts without support. The fully ground shank improves runout performance in chucks and collets and allows for easier regrinding when the geometry permits; regrinding should follow the original geometry to maintain the 135° point behavior and drilling quality. Strong recommendation: choose the MetavCUT Twist Drill Type N short for precision metal drilling and contact METAV Werkzeuge for tailored advice and technical support — eMail: info@metav-werkzeuge.com • Tel: +49 2822 7131930 • WhatsApp: +49 170 2837271 Technical data Designation: Twist Drill Brand: MetavCUT Model Series: Standard Line Diameter: 6.3 mm Spiral Length: 63 mm Overall Length: 101 mm Point Angle: 135° Type: Type N Execution: short Colour/Finish: bright finished Shank Execution: fully ground Material: HSS‑G Standard: DIN 338 Suitable for: Drilling Machine, Hand Drill Application: Drills for Metal Manufacturer: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What is a Twist Drill used for and which materials suit the MetavCUT Twist Drill Type N short? The MetavCUT Twist Drill Type N short is primarily used for machining metal; it excels in drilling alloyed and unalloyed steel, cast steel, gusseisen, sintered iron and many non‑ferrous metals. Its short construction and ground geometry make it particularly effective for high‑precision metal holes and demanding industrial tasks. Which three drill types exist? Commonly distinguished drill types are Metal drills, Wood drills, and Masonry/Stone drills; the MetavCUT Twist Drill belongs to the metal drill category and is optimised for machining a wide range of metallic materials.
6.3mm HSS-G Twist Drill DIN 338 ,short, bright finished, Type N - MetavCUT
Twist Drill — MetavCUT Profi Line, 6.3 mm, 135°, Type N, Bright Finished, Short HSS‑G, DIN 338 The Twist Drill is a short Type N drill for Drilling Machines, designed for precise metal drilling in demanding industrial and workshop applications. Short design for higher stability HSS‑G ground for sharp cutting edges 135° tip angle for hard materials Fully ground shank for precise concentricity Conforms to DIN 338 for standardised quality Precision and faster drilling for metal components The MetavCUT short Twist Drill with HSS‑G material combines resilient cutting performance with precise geometry. Its 6.3 mm diameter and 135° tip angle reduce entry forces when penetrating hard metals, shortening drilling time and improving hole quality. This design is particularly suitable when drilling stainless steel or alloyed steels, because the larger tip angle helps centre the tool and minimises wandering on the work surface, delivering cleaner, more accurate holes. Short length increases rigidity and accuracy A shorter overall length means less overhang and therefore significantly higher Stability during machining. The reduced cantilever of this short execution lowers bending and chatter, which allows higher feed rates and better surface finish when compared with longer drills. For bench and machine work where runout and concentricity matter, the short Profi Line variant gives reproducible results and reduces the risk of breakage under heavier cutting loads. Ground geometry and material advantages explained The designation HSS‑G indicates a ground High Speed Steel, produced with CNC grinding to form the flutes and cutting edges. This results in very sharp edges and excellent roundness, which translate into precise holes and easier regrinding when required. The fully ground shank ensures accurate clamping and minimises axial runout in standard Drilling Machines. Customers benefit from improved tool life in many metalworking tasks, provided suitable cooling and moderate cutting parameters are used. Built for demanding metalworking tasks This Type N normal‑spiral drill is optimised for a wide range of metallic materials. It is particularly recommended for alloyed and unalloyed steels, cast and ductile irons, sintered metals and non‑ferrous metals, as well as hard plastics. The combination of short design, fully ground shank, and 135° tip supports reliable centring and consistent hole quality, making it a solid choice for toolrooms, maintenance shops and production environments focused on repeatable accuracy. Who should choose this Profi Line short Twist Drill Engineers, machinists and workshop professionals seeking reliable, precise metal drilling will appreciate the balance of speed and robustness offered by this tool. The short Twist Drill suits stationary and light moving machine applications where stability is crucial. For users prioritising easy reconditioning and sharp cut performance, the HSS‑G ground version offers straightforward resharpening and consistent results across repeated operations. Strong recommendation: Choose the MetavCUT Profi Line short Twist Drill for precision metal drilling — for expert, non‑binding advice contact METAV Werkzeuge by eMail: info@metav-werkzeuge.com, Phone: +49 2822 7131930, or WhatsApp: +49 170 2837271 Twist Drill Marke: MetavCUT SKU: 48063-FDA Diameter: 6.3 mm Tip angle: 135° Type: Type N Material: HSS‑G Execution: Short Spiral length: 63 mm Overall length: 101 mm Shank execution: Fully ground Finish/Colour: Bright finished Model series: Profi Line Application: Drills for metal For drilling machine: Drilling Machine Norm: DIN 338 Packaging unit: 10 Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What is the Twist Drill used for? The MetavCUT Twist Drill (Type N) is primarily applied to the machining of high‑strength materials and larger bore diameters. Its short, ground geometry is easier to sharpen and remains durable under greater loads, which makes it suitable for industrial metal drilling where tool resilience and repeatable hole quality are required. Which three drill types exist? When comparing drill categories, there are Metal drills, Wood drills and Stone/Concrete drills. The MetavCUT Twist Drill belongs to the Metal drills group and is engineered specifically for metalworking tasks rather than woodworking or masonry.
6.4mm HSS Twist Drill DIN 338 ,short, roll forged, black, Type N - MetavCUT
Twist Drill — Type N short HSS drill, 6.4 mm, 118°, black, DIN 338, MetavCUT The Twist Drill Type N short by MetavCUT is a compact metalworking drill for precise holes in steel and non-ferrous materials, designed for use with a hand drill and compliant with DIN 338. 6.4 mm diameter for accurate metal holes Short design per DIN 338 for high stability HSS material for elasticity and wear resistance 118° point angle for reliable centering Stability and precision for demanding metalworking A short spiral drill made to DIN 338 reduces overhang and vibration, so even thin-walled components can be drilled with greater dimensional accuracy. The reduced exposed length improves rigidity and lowers the risk of deflection, which means cleaner holes and less rework for metalworking professionals. This compact design is particularly advantageous when working from fixed jigs or on small workpieces where stability is essential. High-Speed Steel construction for standard machining tasks Manufactured from HSS (High Speed Steel), this Type N short drill combines toughness with a degree of flexibility that reduces fracture risk during common metal drilling jobs. For standard operations in alloyed and unalloyed steel, cast iron, non-ferrous metals and plastics, the material choice supports longer tool life under frequent use. The construction method improves resistance to chipping when drilling diameters under 6 mm and contributes to consistent drilling performance. Tip geometry and application suitability explained The 118° point angle favours reliable centering and controlled penetration in softer to medium-hard metals, making it well suited for general workshop use. As a Type N twist drill, it is optimised for metalworking rather than soft timber; the point geometry and flute design balance chip evacuation with cutting stability. Correct feed and moderate speeds prolong service life and yield round, burr-minimised holes for subsequent finishing operations. Who benefits from this short Type N twist drill Workshops, maintenance technicians and precision hobbyists seeking a robust everyday metal drill will appreciate the combination of 6.4 mm diameter, short overall length and HSS material. The tool is intended for use in hand-held drilling machines and small bench machines where operator control and low runout are priorities. Its design supports repeatable results for production runs of small to medium series or for single, critical repair tasks. Choose the MetavCUT Twist Drill Type N short for dependable metal drilling performance — for technical advice or to confirm suitability for your application contact METAV Werkzeuge: info@metav-werkzeuge.com | +49 2822 7131930 | WhatsApp +49 170 2837271 Technical Data Designation: Twist Drill Brand: MetavCUT SKU: 40064-FDA Diameter: 6.4 mm Spiral length: 63 mm Overall length: 101 mm Point angle: 118° Type: Type N Execution: short For use with: Hand Drill Colour: black Material: HSS Application: Drills for metal Standard: DIN 338 Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What is the Twist Drill Type N short best used for? The MetavCUT Twist Drill Type N short is primarily used for drilling metal; it excels in producing precise holes in alloyed and unalloyed steels, cast iron and non-ferrous metals when used in hand-held or small stationary drilling machines. Can the Twist Drill Type N short be used in wood? The MetavCUT Twist Drill Type N short can be used in wood, but as a metal-optimised drill it provides less guidance and a rougher finish than dedicated wood drills; it is easier to resharpen yet offers reduced self-feeding compared with timber-specific bits. What are Twist Drills used for? Twist Drills are mainly applied to the machining of high-strength materials and larger drill diameters; their form makes them straightforward to resharpen and able to withstand higher loads. Which three drill types exist? The principal categories are Metal drill, Wood drill, and Stone/Concrete drill. Why are twist drills sharpened (pointed)? Pointing reduces the cross edge at the tip of the Twist Drill, lowering friction and required feed forces while improving the drill's centring in the workpiece. At what drilling depths are twist drills most commonly used? A solid through-hole is typically executed with a Twist Drill; for diameters up to 20 mm and drilling depths up to 100 mm, the Twist Drill is the most common tool. Is HSS or HSSE better? The general assumption that HSSE steels are always superior to HSS is not universally correct; selection should consider actual working conditions and whether the higher cost of HSSE is justified.
6.4mm HSS-E Twist Drill DIN 338 ,short, 5% cobalt-alloyed, Type N - MetavCUT
Twist Drill Type N — 6.4 mm, 135°, short, 5% cobalt-alloyed, HSS‑E, DIN 338 The Twist Drill Type N is a short HSS‑E metal drill designed for precise work in Hand Drilling Machines and stationary setups. Short design for increased rigidity and accuracy 135° point angle for hard materials like stainless steel HSS‑E with 5% cobalt for improved heat resistance Fully ground shank for high concentricity and clean holes Compliant with DIN 338 for short twist drills Greater Precision through a Short, Stable Design The short configuration of this Twist Drill minimises overhang and produces higher stability during drilling, which directly benefits precision and reduces the risk of wandering. The fully ground Shank delivers excellent concentricity, resulting in cleaner, rounder holes in Metal. For operators seeking reproducible results on benches or in jigs, the reduced tendency to deflect means less rework and better fit for threaded components. Suited to Hard Materials — Faster Penetration, Better Control With a 135° Point Angle and the Type N Normal Spiral geometry, this short HSS‑E tool is optimised for demanding tasks in Steel, Cast Iron and other hard materials. The geometry shortens initial touch‑in time and helps maintain the centre when starting a hole. Compliance with DIN 338 indicates manufacture to accepted dimensions and tolerances for short twist drills, supporting consistent performance across batches and easy integration in production workflows. Practical Guidance for Efficient Use Use the Twist Drill in a suitable Drilling Machine with adequate clamping and coolant to extend tool life. The 5% cobalt-alloyed composition increases heat resistance, allowing for higher cutting temperatures and improved wear stability; nevertheless, coolant or lubricant is advised for continuous or deep drilling. The shorter overall length favours operations where stiffness and tool control are critical, such as drilling into thicker plates or working with tight positional tolerances. Material and Handling Benefits from HSS‑E Chemistry The HSS‑E grade combined with 5% cobalt yields a balance of hardness and toughness that performs well under thermal load. The Standard Line production and the fully ground flute geometry create sharp cutting edges and excellent runout characteristics. Operators should note that ground drills offer superior hole quality but can be more brittle than rolled alternatives; therefore, controlled feed rates and proper cooling will help prevent chipping and extend service intervals. Strong recommendation: Choose the MetavCUT short Twist Drill for demanding metal applications and contact METAV Werkzeuge for expert advice and personalised support — eMail: info@metav-werkzeuge.com · Phone: +49 2822 7131930 · WhatsApp: +49 170 2837271 Designation: Twist Drill Brand: MetavCUT SKU: 47064-FDA Type: Type N Diameter: 6.4 mm Point Angle: 135° Execution: short Overall Length: 101 mm Spiral Length: 63 mm Material: HSS‑E Colour / Surface: 5% cobalt-alloyed Shank: fully ground Application: Drills for metal For Drilling Machine: Drilling Machine Model Series: Standard Line Norm: DIN 338 Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What is the MetavCUT Twist Drill Type N used for? The MetavCUT Twist Drill Type N is primarily used for drilling Metal and is suitable for demanding applications where a short, stiff tool is required. It is especially effective on harder materials thanks to the 135° point angle and HSS‑E chemistry, which together improve centring and heat resistance. For what is a Twist Drill used? A Twist Drill is mainly applied to the machining of high‑strength materials and larger bore diameters. Its form allows relatively simple resharpening and it withstands higher loads. This geometry is commonly used where durability and the ability to drill tough materials are required. Which 3 drill types are there? Common classifications are Metal drills, Wood drills, and Masonry/Concrete drills. Why are Twist Drills point‑ground? Point grinding reduces the cross‑cut at the tip of the Twist Drill, which lowers friction and consequently the required feed forces. In addition, a ground tip improves centring in the workpiece and leads to more accurate, controlled drilling.
High-performance drill bits for demanding production
Drill bits designed for industrial manufacturing where precision, repeatability and tool life are decisive. Based on a spectrum from HSS and kobalt-alloyed hss-e for universal use to solid carbide drills for high-speed, high-precision serial production, this range covers applications from general engineering to automotive supplier work.
Why these drill bits are essential in the workshop and on the machining centre
Function and behaviour:
- primary use: creating accurate cylindrical holes
- typical machines: CNC machining centres, lathes and drill presses
- key design aspects: optimised chisel edge, defined point angles, flute geometry for reliable chip evacuation
Technical advantages and process benefits:
- reduced feed forces through optimised point geometry
- improved heat control with advanced coatings and, where specified, internal coolant supply
- extended tool life using solid carbide variants and multilayer coatings such as TiN / TiAlN
- process security on challenging materials thanks to tailored materials and geometries
Concrete benefits that boost productivity and quality
- predictable tool life and fewer tool changes, lowering machine downtime
- stable hole quality and consistent tolerances across long runs
- efficient chip control and thermal management for safe deep-hole and hardened-material drilling
- suitability across a wide material range, reducing the need for multiple specialised tools
Metav as a reliable partner for high-precision tooling
Metav combines decades of sector expertise with a broad, dependable offering from its Emmerich facility. With over 48,000 customers and more than 250,000 products, Metav positions its range of drill bits, twist drills and indexable drills as a practical, quality-first choice for procurement managers and production engineers seeking dependable supply and technical competence.
Technical data (at a glance)
- material: HSS, kobalt-alloyed hss-e, solid carbide
- coatings: TiN, TiAlN, advanced nanocoatings
- coolant option: internal coolant feed where specified
- typical applications: mild steel, high-alloy stainless steel, cast iron, non-ferrous metals, technical plastics, hardened materials (use solid carbide variants)
- tool types available: twist drills, solid carbide drills, indexable drills, centre and pilot drills, step drills
FAQ
What is the difference between hss and solid carbide drill bits?
HSS drill bits offer toughness and resistance to breakage for general machining, while solid carbide drills provide higher wear resistance and are the preferred choice for high-speed, high-volume machining and hardened materials.
Which coatings improve tool life for industrial drilling?
Coatings such as TiN and TiAlN increase surface hardness and thermal stability; when combined with the correct drill geometry and, if available, internal coolant, they significantly extend the service life of drill bits.
Can these drill bits be used on CNC machining centres for deep holes?
Yes. Drill bits designed with optimised flute geometry and internal coolant supply are suited to deep-hole machining on CNC machining centres, ensuring controlled chip evacuation and heat management.
How should I choose between twist drills, solid carbide drills and indexable drills?
Select twist drills for general-purpose drilling, solid carbide drills for high-speed and hardened-material applications, and indexable drills for large-diameter holes where insert changes offer economic advantages.
Why choose Metav for drill bits and drilling solutions?
Metav offers a comprehensive selection of drill bits, twist drills and indexable drills combined with sector expertise, centralised supply from Emmerich and proven reliability across thousands of industrial customers.
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com