Twist Drill Bits for Professionals: Quality You Can Rely On

Twist Drill (Type N) — short HSS‑G, 9.7 mm, 135° point, bright finished, DIN 338, fully ground shank — MetavCUT The Twist Drill (Type N) is a short HSS‑G drill designed for precise metal drilling on Drilling Machines and hand drills, combining a 135° point angle with a fully ground shank for stable, accurate holes. Short design for higher stability and precision HSS‑G construction for sharpness and durability 135° point for harder materials and improved centring Fully ground shank for excellent runout accuracy Suited to alloyed and unalloyed steel, cast and sintered materials Built for demanding metalwork with faster drilling and lower feed forces The Short Design of this Twist Drill follows DIN 338 and reduces overhang from the chuck, resulting in significantly improved Stability and reduced deflection during machining. Made from HSS‑G, the geometry is CNC‑ground to produce very sharp cutting edges; this leads to Faster Drilling (up to 40% quicker in many metals) and Less Feed Force (up to 50% reduction), which helps when working with tough or alloyed steels. These benefits translate directly into higher throughput and fewer re‑works in daily workshop use. Precision features that support clean holes and consistent centring A 135° Point provides a flatter cutting profile ideal for harder workpiece materials, while the Fully Ground Shank and refined flute geometry give excellent Precision and Runout Accuracy. With a 9.7 mm Diameter, a Spiral Length of 87 mm and an Overall Length of 133 mm, this short Twist Drill maintains rigidity without sacrificing effective drilling depth. These design choices make it especially suitable where hole quality and repeatability are essential. Optimised for metal: recommended applications and target users This Twist Drill is intended primarily as a Drill for Metal and performs well in alloyed and unalloyed Steel, Cast Steel, Gusseisen, Sintered Iron, Non‑Ferrous Metals and Hard Plastics. Professional workshops, toolrooms and maintenance crews that require precise, repeatable holes in tougher materials will benefit most from the combination of Type N Normal spiral geometry and the HSS‑G (ground) manufacturing method. Handling advice to extend tool life and ensure reliable results To get optimal performance from the ground Twist Drill, use appropriate Cooling and moderate spindle speeds for the chosen material; ground HSS tends to be sharper but can be more brittle than rolled equivalents, so avoid heavy impact or excessive pecking cycles. For stationary machining and production runs, the Short Design offers superior stability; for portable drilling, ensure the chuck grip and pilot guidance are precise. Regular inspection and professional Regrinding will restore cutting edges, but regrind practices should respect the original 135° point geometry. We recommend the MetavCUT short Twist Drill for precision metal drilling — for tailored advice, further technical data or to check suitability for your application, contact METAV Werkzeuge: 📧 info@metav-werkzeuge.com ☎️ +49 2822 7131930 ✔️ WhatsApp +49 170 2837271 Detailed Technical Specifications for Workshop Use Designation: Twist Drill Brand: MetavCUT SKU: 45097-FDA Diameter: 9.7 mm Point Angle: 135° Type: Type N Execution: short Spiral Length: 87 mm Overall Length: 133 mm Material: HSS-G Shank: fully ground Colour: bright finished Standard: DIN 338 Application: Drills for metal For: Drilling Machine Model Series: Standard Line Manufacturer: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ How does the MetavCUT Twist Drill differ from a rolled HSS drill? The MetavCUT Twist Drill in HSS‑G (ground) form is CNC ground to create very sharp cutting edges and high runout accuracy; this yields cleaner holes and faster penetration in many metals compared with rolled HSS drills, though ground drills can be more brittle and benefit from controlled cutting parameters. Is the MetavCUT Twist Drill suitable for stainless steel and other hard alloys? Yes, the MetavCUT Twist Drill with a 135° point and Type N spiral is designed to perform well in harder materials such as stainless and alloyed steels; the short design improves rigidity and helps maintain hole quality in demanding alloys. For what is a Twist Drill used? A Twist Drill is primarily applied to the machining of high‑strength materials and larger bore diameters; its ground form is easy to regrind and resists high loads, making it suitable for precise work in metals. Which three drill types exist? There are three main drill types: Metal Drills, Wood Drills and Stone/Concrete Drills. Why are twist drills sharpened (pointed)? Sharpening reduces the chisel edge at the tip, significantly lowering friction and thus the required feed force, while also improving the drill’s ability to centre in the workpiece. Can you use a Metal Drill in wood? A Metal Drill can be used in wood, but it usually offers poorer guidance and a less clean finish; however, such drills are easier to resharpen and have lower self‑feeding tendencies. For which drilling depths is the Twist Drill most commonly used? A solid‑material bore is commonly executed with a Twist Drill. For diameters up to 20 mm and drilling depths up to 100 mm, the Twist Drill is the most frequently used tool. Is HSS or HSSE better? The common belief that HSSE steels are universally superior to HSS is incorrect; evaluate working conditions carefully to determine whether the higher cost of HSSE is justified for your specific application.

Twist Drill (Spiralbohrer) — Type N short HSS-G, Ø 9.7 mm, 135° A Twist Drill (Spiralbohrer) Type N short in HSS-G designed for precision metal drilling with a Drilling Machine Short design for higher stability and precision Fully ground geometry for clean, accurate holes 135° tip angle optimised for hard metals Up to 40% faster drilling with reduced feed force Conforms to DIN 338 for short cylinder-shank drills Precision and material advantages for demanding metalwork This short HSS-G twist drill is engineered for high-precision machining of metals where clean entry and true running are essential. Thanks to the fully ground geometry, the cutting edges are exceptionally sharp, producing clean, burr-reduced holes with consistent diameters. For demanding applications in alloyed and unalloyed steel, cast steel and non-ferrous metals, the tool delivers reliable results while preserving workpiece integrity. The compact construction reduces vibration and improves concentricity on stationary and portable machines. Short length for greater stability and faster cycles Because the drill has a reduced overall length, the exposed shank is shorter and therefore less prone to bending; this yields high stability during feed and lowers the risk of chatter. The shortened overhang contributes directly to faster, more controlled drilling—manufacturers report up to 40% faster drilling and around 50% less feed force compared with conventional HSS variants. That makes the short design particularly suitable when working with harder materials or in setups that require precise hole quality and repeatability. Tailored for metalworking professionals and specific tasks Intended primarily for metalworking, this Type N drill is excellent for tasks such as through-holes and accurate pilot holes in thicker plates and components. Users in toolrooms, maintenance shops or production lines will benefit from the drill’s balance of toughness and sharpness; it is especially appropriate for Drilling Machines and similar rotating equipment. The 135° tip angle facilitates smoother entry into hard materials like stainless steel, reducing walking at the start and enabling more consistent centring. Practical guidance, norm compliance and machining tips The product conforms to DIN 338, which standardises short cylinder-shank twist drills and clarifies manufacturing methods such as grinding versus roll-formed flutes. In practical terms, "fully ground" means the flutes and point are shaped by CNC grinding to yield higher roundness and sharper land edges; this improves hole finish but can make the tool somewhat more brittle, so use coolant and moderate speeds for best life. When referring to tip geometry, a 135° angle is chosen to reduce penetration resistance in tougher alloys and to extend tool life when cutting harder materials. Strongly recommend the MetavCUT short HSS-G Twist Drill for precise metal drilling applications — for technical questions or to confirm suitability for your project, contact METAV Werkzeuge for expert advice via info@metav-werkzeuge.com or call +49 2822 7131930, WhatsApp +49 170 2837271 Designation: Twist Drill (Spiralbohrer) Brand: MetavCUT SKU: 48097-FDA Type: Type N Diameter: 9.7 mm Spiral length: 87 mm Overall length: 133 mm Tip angle: 135° Material: HSS-G Execution: short Shaft execution: fully ground Colour: bright finished For: Drilling Machine Norm: DIN 338 Model series: Profi Line Application: Drills for metal Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What is the Twist Drill (Spiralbohrer) from MetavCUT used for? The MetavCUT Twist Drill (Type N) is primarily applied to machining high-strength materials and larger drill diameters; its short design and ground geometry make it suitable for precise work in steel, cast materials and hard plastics. The shape is easy to regrind and remains stable under heavier loads. Which three drill types exist? There are three common drill categories: metal drills, wood drills and stone/concrete drills. The MetavCUT Twist Drill falls into the metal-drill category and is optimised for that application.

Twist Drill — Type N, 9.8 mm, HSS, short, black, DIN 338 A Twist Drill Type N for precise metalworking, designed as a short HSS drill with a 9.8 mm diameter and 118° tip angle for stable, accurate holes. Short design for improved stability HSS for robust metal drilling 118° tip for reliable centring Type N normal spiral for metal Conforms to DIN 338 standard Exceptional durability through high-speed steel and standardised design Crafted from HSS (High Speed Steel), this short drill delivers consistent wear resistance and elasticity for demanding metal operations. Because the bit meets DIN 338, the geometry and dimensions are engineered for repeatable performance, which supports longer tool life and predictable results. The combination of short design and quality material reduces the risk of breakage during standard drilling tasks and is particularly beneficial when precision matters. Stable drilling and improved hole quality with optimised geometry Thanks to the short overall length and a 118° tip angle, the bit offers enhanced stability and easier centring on curved or imperfect surfaces. A Type N normal spiral provides efficient chip evacuation in many metalworking scenarios, which helps maintain a clean bore and minimises heat buildup. This geometry is especially suitable when a reliable entry point and steady axial guidance are required. Built for metalworking on standard drilling machines Intended for use in a Drilling Machine, the design focuses on common metal applications including alloyed and unalloyed steels, cast iron, non-ferrous metals and plastics. For tasks up to moderate diameters, the combination of HSS and the Type N spiral ensures dependable performance. Users seeking precision in metal fabrication, maintenance or workshop settings will find the tool aligns with those practical requirements. Maintenance tips and selection guidance for safe, accurate use Regular inspection and timely resharpening preserve the geometry and reduce cutting forces. The short version is easier to stabilise in the chuck and simpler to regrind when necessary. Note that the Type N spiral is optimised for metals and is less suited to very soft woods where guidance and finish may be inferior. For complex requirements or if uncertain about suitability, technical advice is recommended to match tool selection to the material and machine. Strongly recommended for precise metal drilling: choose the MetavCUT Type N Twist Drill for durability and stability — for personalised advice contact METAV Werkzeuge at info@metav-werkzeuge.com, phone +49 2822 7131930 or WhatsApp +49 170 2837271 Bezeichnung: Twist Drill Marke: MetavCUT SKU: 40098-FDA Durchmesser: 9.8 mm Spitzenwinkel: 118° Typ: Type N Ausführung: short Farbe: black Material: HSS Norm: DIN 338 Gesamtlänge: 133 mm Spiral-Länge: 87 mm Anwendung: Drills for metal Für Bohrmaschine: Drilling Machine Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What applications suit the Twist Drill by MetavCUT Type N? The MetavCUT Twist Drill Type N is primarily intended for metalworking; the design and HSS material make it well suited to alloyed and unalloyed steels, cast iron and many non-ferrous metals where stable, precise holes are required. How does the short Twist Drill version affect performance? A short Twist Drill from MetavCUT reduces overhang from the chuck, increasing stiffness and improving hole accuracy while lowering the chance of runout or breakage in typical metal drilling tasks. For what is a Twist Drill used? Twist Drills are mainly applied when machining high-strength materials and for larger hole diameters. This design is easy to regrind and withstands greater loads. Which three drill types exist? There are three main drill categories: metal drills, wood drills and stone/concrete drills. Why are twist drills sharpened at the tip? Tip sharpening reduces the cross-edge at the point of the Twist Drill, lowering friction and required feed force while improving centring of the tip in the workpiece. Can a metal Twist Drill be used for wood? A metal Twist Drill can be used in wood but typically offers inferior guidance and a rougher finish. It is easier to resharpen and has less self-feed compared with dedicated wood drills. At which drilling depths is the Twist Drill most used? A full bore is commonly executed with a Twist Drill. For diameters up to 20 mm and depths up to 100 mm, the Twist Drill is the most frequently used tool. What is better, HSS or HSSE? The common belief that HSSE steels are categorically superior to HSS is incorrect. Assess working conditions carefully to decide whether the higher cost of HSSE is justified.

Twist Drill — Short Type N, Ø 9.8 mm, 135°, HSS‑E, 5% cobalt‑alloyed, Fully Ground, DIN 338 The Twist Drill short Type N is a precision metal drilling bit for Drilling Machines, optimised for hard and alloyed metals with high heat resistance. Short design for increased stability and precision HSS‑E with 5% cobalt for higher heat resistance 135° point angle for hard metals and stainless steel Fully ground shank for sharp cutting and precise holes Conforms to DIN 338 for reliable industrial quality Durable Material for High‑Heat Metalworking and Longer Tool Life Thanks to its HSS‑E composition with 5% cobalt, this short Twist Drill delivers improved hardness and thermal stability compared with standard HSS. The cobalt‑alloyed steel retains cutting edge at elevated temperatures, reducing wear when drilling alloyed and unalloyed Steel, Cast Iron, Non‑Ferrous Metals and certain Plastics. This results in fewer tool changes and more consistent hole quality under demanding conditions. Short Geometry for Precision and Reduced Deflection The Short Design reduces the unsupported length outside the chuck, which significantly improves stability and minimises bending during cutting. Combined with the Fully Ground spiral geometry, the bit produces clean, accurate holes with excellent concentricity. The 135° Point Angle shortens the initial penetration time in harder materials and improves centring when machining stainless and other tough alloys. Built for Workshop and Industrial Metal Drilling Tasks Engineered according to DIN 338 and classified as Type N, this bit is intended for professional metalworking on Drilling Machines and stationary equipment. Typical applications include precision component fabrication and repair work where repeatable hole quality is required. For many workshop tasks the short configuration is preferred up to common diameter and depth ranges, offering dependable performance for production and maintenance environments. Practical Use Recommendations to Maximise Performance For best results, use appropriate cutting speeds and steady coolant to extend life and prevent overheating. The distinction between Ground and Rolled manufacturing matters: ground bits give sharper cutting edges and superior hole finish but can be less tolerant to shock; rolled bits are tougher but may sacrifice final surface quality. Secure clamping, correct speeds and feed rates, and lubrication ensure the best balance of lifetime and hole accuracy. Strongly recommend MetavCUT short Twist Drill for precision metalworking — for expert advice and to confirm suitability contact METAV Werkzeuge: 📧 info@metav-werkzeuge.com ☎️ +49 2822 7131930 ✔️ WhatsApp +49 170 2837271 Technical Data Twist Drill Brand: MetavCUT SKU: 47098-FDA Type: Type N Diameter: 9.8 mm Spiral length: 87 mm Overall length: 133 mm Point angle: 135° Material: HSS‑E Colour / Alloy: 5% cobalt-alloyed Shank finish: Fully ground Execution: Short Norm: DIN 338 Application: Drills for metal Model series: Standard Line Suitable for: Drilling Machine Manufacturer: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What is the MetavCUT Twist Drill Type N used for? The MetavCUT Twist Drill Type N is primarily used for machining high‑strength and harder metals where precision holes are required; its short design and HSS‑E material make it suitable for demanding metalwork and larger drilling diameters under controlled conditions. Which three drill types exist? The three main drill categories are Metal Drills, Wood Drills and Stone/Concrete Drills, each optimised in geometry and cutting angle for their respective materials. How does the MetavCUT Twist Drill Type N perform in high‑strength materials? The MetavCUT Twist Drill Type N is designed for high‑strength materials; its geometry and alloy content allow efficient cutting of tougher metals, and the form is easy to regrind while withstanding higher loads. Can metal Twist Drills be used for wood? A Metal Drill such as the MetavCUT Twist Drill can be used in Wood, but guidance and finish are typically inferior compared with dedicated Wood Drills; Metal Drills are easier to resharpen and have lower self‑feeding tendency.

Spiralbohrer 9,8 mm, 135°, Typ N, blank, kurz, DIN 338, HSS-G von MetavCUT Der Spiralbohrer ist ein kurzer HSS-G Metallbohrer nach DIN 338 für präzise Bohrungen in legierten und unlegierten Stahl sowie Gusswerkstoffe. Kurze Ausführung für höhere Stabilität HSS-G geschliffen für saubere Bohrlöcher Spitzenwinkel 135° für harte Werkstoffe Normkonform nach DIN 338 für Zylinderschaft Geeignet für Handbohrmaschine und stationäre Maschinen Präzision und Standfestigkeit beim Metallbohren Die kurze Ausführung des Spiralbohrers reduziert die Auskraglänge und erhöht dadurch die Stabilität sowie die Bohrgenauigkeit. Durch die geschliffene HSS-G Geometrie entsteht eine sehr scharfe Schneide, die ein bis zu 40 % schnelleres Bohren ermöglicht und gleichzeitig 50 % weniger Anpresskraft erfordert. Dies führt zu saubereren Bohrlöchern und reduziert die Ermüdung bei längeren Arbeitszyklen, was besonders bei präzisen Maschinenbau- und Instandsetzungsarbeiten relevant ist. Materialkompatibilität und typische Einsatzfelder Der Bohrer eignet sich gezielt für das Bohren in legierten und unlegierten Stahl, Gussstahl, Gusseisen, Sintereisen, Temperguss, Nichteisenmetalle und Hartkunststoff. Als Typ N mit Normalspirale bietet er eine ausgewogene Spanabfuhr bei Metallarbeiten und ist weniger geeignet für sehr weiche Werkstoffe. Eingesetzt wird der Bohrer sowohl in Handgeführten Bohrmaschinen als auch in stationären Bohrmaschinen, wobei die kurze Bauform besonders bei Anwendungen mit eingeschränktem Auskragmaß und hoher Präzisionsanforderung Vorteile bringt. Fertigungsqualität, Norm und Schaftausführung Die Ausführung als geschliffener Spiralbohrer (HSS-G) garantiert hohe Rundlaufgenauigkeit und sehr scharfe Kanten, wie sie in der DIN 338 für kurze Spiralbohrer mit Zylinderschaft gefordert wird. Gegenüber rollgewalzten Varianten bietet der CNC-Schliff bessere Oberflächen und präzisere Bohrbilder, wobei Anwender beachten sollten, dass geschliffene Werkzeuge empfindlicher gegenüber Stoßbelastungen sind und daher bevorzugt mit Kühlung und in stationärem Betrieb verwendet werden sollten. Praktische Hinweise für optimale Ergebnisse Für den Durchmesser 9,8 mm empfiehlt sich das direkte Bohren mit angepasster Drehzahl und moderatem Vorschub; bei besonders hoher Präzisionsanforderung kann zuvor ein Zentrierbohrer gesetzt werden. Zur Verlängerung der Standzeit sind passende Kühlschmierstoffe und eine gleichmäßige Kühlung empfehlenswert. Die kurze Spiralbohrer-Geometrie minimiert Vibrationen; trotzdem sollte auf eine feste Werkstückspannung und eine korrekte Spannfutteraufnahme geachtet werden, um Bruchrisiken zu reduzieren. Empfehlung: Für präzise Metallbohrungen die MetavCUT Standard Line wählen und bei technischen Fragen METAV Werkzeuge kontaktieren unter info@metav-werkzeuge.com oder Telefon +49 2822 7131930 Bezeichnung: Spiralbohrer 9,8 mm, kurz, HSS-G, Typ N, 135° Marke: MetavCUT SKU: 45098-FDA Durchmesser: 9,8 mm Gesamtlänge: 133 mm Spirallänge: 87 mm Spitzenwinkel: 135° Material: HSS-G Schaftausführung: geschliffen Ausführung: kurz Typ: Typ N Norm: DIN 338 Farbe: blank Für Bohrmaschine: Handbohrmaschine Modellserie: Standard Line Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ Für welche Materialien ist der Spiralbohrer von MetavCUT geeignet? Der Spiralbohrer von MetavCUT (Typ N) ist ausgelegt für legierten und unlegierten Stahl, Gussstahl, Gusseisen, Sintereisen, Temperguss, Nichteisenmetalle und Hartkunststoff und liefert in diesen Werkstoffen besonders saubere Bohrbilder. Kann der Spiralbohrer 9,8 mm in einer Handbohrmaschine verwendet werden? Ja, der Spiralbohrer von MetavCUT eignet sich für den Einsatz in Handbohrmaschinen sowie in stationären Maschinen; bei stationärem Betrieb sind Kühlung und feste Werkstückspannung zur Standzeitverbesserung empfehlenswert. Warum ist der Spitzenwinkel 135° vorteilhaft und was bedeutet das für die Anwendung? Der 135° Spitzenwinkel des MetavCUT Spiralbohrers reduziert das Auswandern beim Anbohren und ist besonders vorteilhaft bei harten Werkstoffen wie Edelstahl oder gehärtetem Stahl, da er die Anbohrzeit verkürzt und die Zentrierung verbessert. Welche Pflege und Anwendungstipps gelten für den geschliffenen HSS-G Spiralbohrer? Für den geschliffenen HSS-G Spiralbohrer von MetavCUT empfiehlt sich der Einsatz von Kühlschmierstoff, eine konstante Drehzahl sowie eine stabile Spannfutteraufnahme; geschliffene Bohrer liefern präzisere Ergebnisse, sind aber empfindlicher gegen Stoßbelastung. {"@context":"https://schema.org","@graph":[{"@type":"Product","@id":"#45098-FDA","sku":"45098-FDA","mpn":"45098-FDA","name":"Spiralbohrer 9,8 mm, kurz, HSS-G","description":"Spiralbohrer kurz, HSS-G, Typ N, Spitzenwinkel 135°, blank, DIN 338; Geschliffene Geometrie für präzise Bohrungen in legiertem und unlegiertem Stahl sowie Gusswerkstoffen; kurze Ausführung für höhere Stabilität und reduzierte Vibrationen.","image":["https://files.plytix.com/api/v1.1/file/public_files/pim/assets/57/c3/98/62/6298c3575d155f1bc7e497fd/images/8e/48/c5/69/69c5488eb2b3400ba580741c/logo-metav-1200-675.png","https://files.plytix.com/api/v1.1/file/public_files/pim/assets/57/c3/98/62/6298c3575d155f1bc7e497fd/images/8e/48/c5/69/69c5488eb2b3400ba580741b/logo-metav-1200-1200.png","https://files.plytix.com/api/v1.1/file/public_files/pim/assets/57/c3/98/62/6298c3575d155f1bc7e497fd/images/8e/48/c5/69/69c5488eb2b3400ba580741e/logo-metav-1200-900.png"],"additionalProperty":[{"@type":"PropertyValue","name":"Bezeichnung","value":"Spiralbohrer 9,8 mm, kurz, HSS-G, Typ N, 135°"},{"@type":"PropertyValue","name":"Durchmesser","value":"9,8 mm"},{"@type":"PropertyValue","name":"Spitzenwinkel","value":"135°"},{"@type":"PropertyValue","name":"Typ","value":"Typ N"},{"@type":"PropertyValue","name":"Farbe","value":"blank"},{"@type":"PropertyValue","name":"Ausführung","value":"kurz"},{"@type":"PropertyValue","name":"Norm","value":"DIN 338"},{"@type":"PropertyValue","name":"Material","value":"HSS-G"},{"@type":"PropertyValue","name":"Schaftausführung","value":"geschliffen"},{"@type":"PropertyValue","name":"Gesamtlänge","value":"133 mm"},{"@type":"PropertyValue","name":"Spirallänge","value":"87 mm"},{"@type":"PropertyValue","name":"Für Bohrmaschine","value":"Handbohrmaschine"},{"@type":"PropertyValue","name":"Modellserie","value":"Standard Line"},{"@type":"PropertyValue","name":"Hersteller","value":"MetavCUT"},{"@type":"PropertyValue","name":"Anwendung","value":"Bohrer für Metall"}]},{"@type":"FAQPage","mainEntity":[{"@type":"Question","name":"Für welche Materialien ist der Spiralbohrer geeignet?","acceptedAnswer":{"@type":"Answer","text":"Der Spiralbohrer 9,8 mm von MetavCUT (Typ N) eignet sich für legierten und unlegierten Stahl, Gussstahl, Gusseisen, Sintereisen, Temperguss, Nichteisenmetalle und Hartkunststoff und liefert in diesen Werkstoffen saubere Bohrbilder."}},{"@type":"Question","name":"Kann der Spiralbohrer in einer Handbohrmaschine verwendet werden?","acceptedAnswer":{"@type":"Answer","text":"Ja, der Spiralbohrer 9,8 mm von MetavCUT ist für Handbohrmaschinen und stationäre Maschinen geeignet; bei stationärem Betrieb verlängern Kühlung und feste Werkstückspannung die Standzeit."}},{"@type":"Question","name":"Warum ist der Spitzenwinkel 135° vorteilhaft?","acceptedAnswer":{"@type":"Answer","text":"Der Spitzenwinkel 135° des MetavCUT Spiralbohrers reduziert das Auswandern beim Anbohren und ist besonders vorteilhaft bei harten Werkstoffen, da er die Anbohrzeit verkürzt und die Zentrierung verbessert."}},{"@type":"Question","name":"Welche Pflege- und Anwendungstipps gelten für den geschliffenen HSS-G Spiralbohrer?","acceptedAnswer":{"@type":"Answer","text":"Für den geschliffenen HSS-G Spiralbohrer von MetavCUT empfiehlt sich Einsatz von Kühlschmierstoff, konstante Drehzahl und stabile Spannfutteraufnahme; geschliffene Bohrer liefern präzisere Ergebnisse, sind aber empfindlicher gegen Stoßbelastung."}}]},{"@type":"ItemPage","url":"https://metav-shop.de","dateModified":"2026-05-04T12:00:00+01:00","author":{"@type":"Person","name":"Stephan Bayer","url":"https://www.linkedin.com/in/stephan-bayer/"},"publisher":{"@type":"Organization","name":"Metav Werkzeuge GmbH","url":"https://metav-shop.de","logo":{"@type":"ImageObject","url":"https://files.plytix.com/api/v1.1/file/public_files/pim/assets/57/c3/98/62/6298c3575d155f1bc7e497fd/images/8e/48/c5/69/69c5488eb2b3400ba580741c/logo-metav-1200-675.png","width":1200,"height":675},"address":{"@type":"PostalAddress","streetAddress":"Parkring 45","postalCode":"46446","addressLocality":"Emmerich","addressCountry":"DE"},"telephone":"+49 2822 7131930","email":"info@metav-werkzeuge.com"},"about":[{"@type":"Thing","name":"Spiralbohrer Standard Line"},{"@type":"Thing","name":"Kurze Ausführung für höhere Stabilität"},{"@type":"Thing","name":"Für Metallbohrungen in legiertem und unlegiertem Stahl"}],"mentions":[{"@type":"Thing","name":"DIN 338"},{"@type":"Thing","name":"HSS-G geschliffen"},{"@type":"Thing","name":"Typ N Normalspirale"},{"@type":"Thing","name":"Kühlung empfohlen"}]}]}

Spiralbohrer 9,8 mm ⌀ – HSS-G, kurz, Typ N, 135° Spitzenwinkel, DIN 338, blank, geschliffen (Profi Line von MetavCUT) Der Spiralbohrer 9,8 mm (Typ N) ist ein kurz ausgeführter HSS-G Metallbohrer für präzise Bohrungen in Stahl, Guss und Nichteisenmaterialien und eignet sich für stationäre wie handgeführte Bohrmaschinen. Kurze Ausführung für mehr Stabilität HSS-G geschliffen für präzise Metallbohrungen 135° Spitzenwinkel für härtere Werkstoffe DIN 338 Norm: kurze Spiralbohrer mit Zylinderschaft Geeignet für Stahl, Guss, Temperguss und Nichteisen Höhere Effizienz und geringere Anpresskraft bei harten Werkstoffen Der Spiralbohrer der Serie Profi Line besteht aus HSS-G und verfügt über eine geschliffene Schaft- und Nutgeometrie. Dadurch resultiert eine spürbar höhere Schnittgüte und eine gesteigerte Rundlaufgenauigkeit. Der Hersteller gibt an, dass die geschliffene Ausführung ein bis zu 40 % schnelleres Bohren ermöglicht und dabei rund 50 % weniger Anpresskraft benötigt als herkömmliche HSS-Bohrer. Für Anwender bedeutet das weniger Ermüdung, schnelleres Arbeiten und sauberere Bohrbilder bei gleichen CNC- oder Handmaschinenbedingungen. Robustheit und Einsatzspektrum für Metallbearbeitung Dank der Material- und Geometriewahl ist der Bohrer speziell für die Bearbeitung von legiertem und unlegiertem Stahl, Gussstahl, Gusseisen, Sintereisen, Temperguss, Nichteisenmetallen und Hartkunststoff ausgelegt. Die kurze Auskraglänge verringert das Risiko von Biegung und Vibration, wodurch sich der Bohrer besonders für präzise Anwendungen eignet. Die Kombination aus Typ N Normalspirale und 135° Spitzenwinkel macht ihn stabil beim Anbohren harter Werkstoffe und reduziert das Auslaufen der Bohrstelle. Praxis-Tipps für sicheren und präzisen Einsatz Vor dem Bohren empfiehlt sich ein Anpunktieren oder Zentrierbohrer, um das Wandern beim Ansetzen zu minimieren; bei einem Durchmesser im Standardbereich ist direktes Bohren möglich, doch Anpunkten erhöht die Präzision. Bei harten Werkstoffen und längeren Bohrzyklen wird Kühlung eingesetzt, um Standzeit und Schnittqualität zu verbessern. Die kurze Spirallänge und der geschliffene Schaft begünstigen die Stabilität; tiefe Bohrungen über das Fünffache des Durchmessers sollten vermieden oder stufenweise vorgebohrt werden, um Späne sicher zu führen. Für welche Anwender sich der Bohrer besonders lohnt Dieser Kurzspiralbohrer richtet sich an Werkstätten, Metallbauer und anspruchsvolle Heimwerker, die Wert auf präzise, saubere Bohrlöcher legen. Die Ausführung eignet sich für den Einsatz an Handbohrmaschinen und stationären Maschinen gleichermaßen, solange die Maschine ausreichende Steifigkeit und Rundlaufqualität bietet. Anwender, die oft in gehärteten oder legierten Werkstoffen arbeiten, profitieren besonders von der kombinierten Geometrie und Materialwahl. Empfehlung: Für präzise Metallbohrungen empfiehlt MetavCUT den Einsatz dieses HSS-G Kurzbohrers; bei Unsicherheit oder Fragen steht METAV Werkzeuge gern mit technischer Beratung per E-Mail info@metav-werkzeuge.com oder Telefon +49 2822 7131930 zur Verfügung Bezeichnung: Spiralbohrer Marke: MetavCUT SKU: 48098-FDA Durchmesser: 9,8 mm Spitzenwinkel: 135° Material: HSS-G Ausführung: kurz Schaft Ausführung: geschliffen Spirallänge: 87 mm Gesamtlänge: 133 mm Typ: Typ N Norm: DIN 338 Farbe: blank Anwendung: Bohrer für Metall Für Bohrmaschine: Handbohrmaschine Modellserie: Profi Line Verpackungseinheit: 5 Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ Ist der Spiralbohrer 9,8 mm von MetavCUT für Edelstahl geeignet? Der Spiralbohrer 9,8 mm von MetavCUT (Typ N, HSS-G, geschliffen) ist für härtere Werkstoffe wie Edelstahl geeignet; wegen der Materialhärte empfiehlt sich Kühlung und angepasste Schnittgeschwindigkeit. Kann der MetavCUT Spiralbohrer 9,8 mm in einer Handbohrmaschine eingesetzt werden? Der MetavCUT Spiralbohrer 9,8 mm wurde unter Beachtung der Norm DIN 338 konzipiert und ist für den Einsatz an Handbohrmaschinen und stationären Maschinen im Standardbereich zugelassen, vorausgesetzt die Maschine bietet ausreichenden Rundlauf. Wie vermeide ich Bruch beim Einsatz des Spiralbohrers 9,8 mm (Typ N)? Um Bruch zu vermeiden, sollte der Spiralbohrer 9,8 mm (MetavCUT, geschliffen) mit zentriertem Ansatz, moderatem Vorschub und bei Bedarf mit Kühlung verwendet werden; die kurze Ausführung reduziert die Neigung zum Verbiegen. Worin unterscheidet sich der geschliffene HSS-G Spiralbohrer 9,8 mm von rollgewalzten Varianten? Der geschliffene HSS-G Spiralbohrer 9,8 mm (MetavCUT, Typ N) bietet schärfere Schneiden und höhere Rundlaufgenauigkeit, was sauberere Bohrlöcher ermöglicht; im Vergleich kann die geschliffene Variante bei unsachgemäßer Handhabung spröder reagieren. {"@context":"https://schema.org","@graph":[{"@type":"Product","@id":"#48098-FDA","sku":"48098-FDA","mpn":"48098-FDA","name":"Spiralbohrer 9,8 mm ⌀ – HSS-G, kurz, Typ N","description":"Kurzspiralbohrer 9,8 mm aus HSS-G, geschliffener Schaft, 135° Spitzenwinkel, DIN 338; geeignet für Stahl, Guss, Temperguss, Nichteisenmetalle und Hartkunststoff; Profi Line für stabile, präzise Metallbohrungen.","image":["https://files.plytix.com/api/v1.1/file/public_files/pim/assets/57/c3/98/62/6298c3575d155f1bc7e497fd/images/8e/48/c5/69/69c5488eb2b3400ba580741c/logo-metav-1200-675.png","https://files.plytix.com/api/v1.1/file/public_files/pim/assets/57/c3/98/62/6298c3575d155f1bc7e497fd/images/8e/48/c5/69/69c5488eb2b3400ba580741b/logo-metav-1200-1200.png","https://files.plytix.com/api/v1.1/file/public_files/pim/assets/57/c3/98/62/6298c3575d155f1bc7e497fd/images/8e/48/c5/69/69c5488eb2b3400ba580741e/logo-metav-1200-900.png"],"additionalProperty":[{"@type":"PropertyValue","name":"Bezeichnung","value":"Spiralbohrer"},{"@type":"PropertyValue","name":"Marke","value":"MetavCUT"},{"@type":"PropertyValue","name":"Durchmesser","value":"9,8 mm"},{"@type":"PropertyValue","name":"Spitzenwinkel","value":"135°"},{"@type":"PropertyValue","name":"Material","value":"HSS-G"},{"@type":"PropertyValue","name":"Ausführung","value":"kurz"},{"@type":"PropertyValue","name":"Schaftausführung","value":"geschliffen"},{"@type":"PropertyValue","name":"Spirallänge","value":"87 mm"},{"@type":"PropertyValue","name":"Gesamtlänge","value":"133 mm"},{"@type":"PropertyValue","name":"Typ","value":"Typ N"},{"@type":"PropertyValue","name":"Norm","value":"DIN 338"},{"@type":"PropertyValue","name":"Farbe","value":"blank"},{"@type":"PropertyValue","name":"Anwendung","value":"Bohrer für Metall"},{"@type":"PropertyValue","name":"Für Bohrmaschine","value":"Handbohrmaschine"},{"@type":"PropertyValue","name":"Modellserie","value":"Profi Line"},{"@type":"PropertyValue","name":"Verpackungseinheit","value":"5"}],"offers":{"@type":"Offer","price":8.25,"priceCurrency":"EUR"}},{"@type":"FAQPage","mainEntity":[{"@type":"Question","name":"Ist der Spiralbohrer 9,8 mm von MetavCUT für Edelstahl geeignet?","acceptedAnswer":{"@type":"Answer","text":"Der Spiralbohrer 9,8 mm von MetavCUT (Typ N, HSS-G, geschliffen) ist für härtere Werkstoffe wie Edelstahl geeignet; wegen der Materialhärte empfiehlt sich Kühlung und angepasste Schnittgeschwindigkeit."}},{"@type":"Question","name":"Kann der MetavCUT Spiralbohrer 9,8 mm in einer Handbohrmaschine eingesetzt werden?","acceptedAnswer":{"@type":"Answer","text":"Der MetavCUT Spiralbohrer 9,8 mm wurde nach DIN 338 ausgelegt und ist für den Einsatz an Handbohrmaschinen und stationären Maschinen geeignet, vorausgesetzt die Maschine bietet ausreichenden Rundlauf."}},{"@type":"Question","name":"Wie vermeide ich Bruch beim Einsatz des Spiralbohrers 9,8 mm Typ N?","acceptedAnswer":{"@type":"Answer","text":"Um Bruch zu vermeiden, sollte der Spiralbohrer 9,8 mm (MetavCUT, geschliffen) mit zentriertem Ansatz, moderatem Vorschub und bei Bedarf mit Kühlung verwendet werden; die kurze Ausführung reduziert die Neigung zum Verbiegen."}},{"@type":"Question","name":"Worin unterscheidet sich der geschliffene HSS-G Spiralbohrer 9,8 mm von rollgewalzten Varianten?","acceptedAnswer":{"@type":"Answer","text":"Der geschliffene HSS-G Spiralbohrer 9,8 mm (MetavCUT, Typ N) bietet schärfere Schneiden und höhere Rundlaufgenauigkeit für sauberere Bohrlöcher; nachteilig kann eine erhöhte Sprödigkeit sein, daher ist sachgemäße Handhabung und Kühlung empfehlenswert."}}]},{"@type":"ItemPage","url":"https://metav-shop.de/produkt/48098-FDA","dateModified":"2026-05-04T12:00:00+01:00","author":{"@type":"Person","name":"Stephan Bayer","url":"https://www.linkedin.com/in/stephan-bayer/"},"publisher":{"@type":"Organization","name":"Metav Werkzeuge GmbH","url":"https://metav-shop.de","logo":{"@type":"ImageObject","url":"https://files.plytix.com/api/v1.1/file/public_files/pim/assets/57/c3/98/62/6298c3575d155f1bc7e497fd/images/8e/48/c5/69/69c5488eb2b3400ba580741c/logo-metav-1200-675.png","width":1200,"height":675},"address":{"@type":"PostalAddress","streetAddress":"Parkring 45","postalCode":"46446","addressLocality":"Emmerich","addressCountry":"DE"},"telephone":"+49 2822 7131930","email":"info@metav-werkzeuge.com"},"about":[{"@type":"Thing","name":"Spiralbohrer Kurz Ausführung"},{"@type":"Thing","name":"HSS-G Geschliffen"},{"@type":"Thing","name":"DIN 338 Kurze Spiralbohrer"}],"mentions":[{"@type":"Thing","name":"Profi Line Modellserie"},{"@type":"Thing","name":"Typ N Normalspirale"},{"@type":"Thing","name":"Geschliffener Schaft"}]}]}

Spiralbohrer Kurz HSS, 9,9 mm, 118°, Typ N, schwarz, DIN 338 von MetavCUT Der Spiralbohrer ist ein kurzer HSS-Bohrer nach DIN 338 für präzise Metallbohrungen mit 9,9 mm Durchmesser und eignet sich besonders für den Einsatz an Handbohrmaschinen. MetavCUT Spiralbohrer, HSS, kurz, DIN 338 9,9 mm Durchmesser für Standard-Metallbohrungen Typ N Normalspirale, optimiert für Stahl und Eisen 118° Spitzenwinkel für zügigen Anbohrvorgang Kurze Ausführung für erhöhte Stabilität und Präzision Höhere Stabilität durch kurze Ausführung und HSS-Werkstoff Der kurze HSS-Spiralbohrer liefert eine deutlich reduzierte Auskraglänge, was die Stabilität beim Bohren erhöht und Vibrationen verringert. Dank des verwendeten HSS (Schnellarbeitsstahl) bleibt die Schneidkante bei normalen Metallbearbeitungen lange scharf, wodurch weniger Nacharbeiten erforderlich sind. Die Konstruktion nach DIN 338 steht für die standardisierte kurze Spiralform mit Zylinderschaft, wodurch die Handhabung an stationären und mobilen Bohrmaschinen vereinfacht wird. Präzise Bearbeitung von Stahl und sonstigen Metallen Mit einem Durchmesser von 9,9 mm fällt dieser Bohrer in den Standard-Bereich für Metallbearbeitung; dadurch ist er besonders geeignet für Werkstatt, Montage und DIY-Projekte mit dünnen bis mittleren Blechen und Profilen. Die Normalspirale (Typ N) gewährleistet zuverlässigen Spanabtransport bei üblichen Werkstoffen wie legiertem und unlegiertem Stahl sowie Gusseisen. Der 118° Spitzenwinkel erleichtert das Anbohren und sorgt für kontrollierten Vorschub ohne übermäßiges Wandern des Bohrers. Praktische Anwendungstipps für sicheres Arbeiten Vor dem Bohren empfiehlt sich das Anpunkten bzw. Zentrieren, um den Bohrer exakt zu führen und Ausbrüche zu vermeiden. Für längere Standzeiten ist der Einsatz geeigneter Kühlschmierstoffe bei hartem Material empfehlenswert; bei normalen Arbeiten in nicht gehärteten Stählen genügen moderate Schnittzahlen und angemessener Vorschub. Die kurze Spirallänge fördert die Präzision, reduziert aber gleichzeitig die Eignung für sehr tiefe Bohrungen — hier ist schrittweises Aufbohren oder der Einsatz längerer Bohrer ratsam. Vertrauen Sie auf den MetavCUT Spiralbohrer in kurzer Ausführung: mit HSS-Material, 118° Spitzenwinkel und 9,9 mm Durchmesser bietet dieser Bohrer stabile Präzision für Metallarbeiten — bei Fragen berät METAV Werkzeuge gern per E‑Mail info@metav-werkzeuge.com oder Telefon +49 2822 7131930 Bezeichnung: Spiralbohrer Marke: MetavCUT SKU: 40099-FDA Durchmesser: 9,9 mm Material: HSS (Schnellarbeitsstahl) Ausführung: kurz Typ: Typ N (Normalspirale) Spitzenwinkel: 118° Farbe: schwarz Gesamtlänge: 133 mm Spirallänge: 87 mm Norm: DIN 338 Für Bohrmaschine: Handbohrmaschine Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ Ist der MetavCUT Spiralbohrer (Typ N) für Handbohrmaschinen geeignet? Der MetavCUT Spiralbohrer in kurzer Ausführung wurde für den Einsatz an Handbohrmaschinen konzipiert und bietet durch die reduzierte Auskraglänge erhöhte Stabilität, sodass er sich für typische Werkstattanwendungen in Metall gut eignet. Für welche Materialien ist der Spiralbohrer von MetavCUT am besten geeignet? Der MetavCUT Spiralbohrer (Typ N, HSS) ist besonders geeignet für legierten und unlegierten Stahl, Gusseisen sowie Nichteisenmetalle; weiche Werkstoffe wie Aluminium lassen sich ebenfalls bearbeiten, bei sehr weichen Materialien ist jedoch ein speziellerer Bohrertyp zu prüfen. Wie beeinflusst der 118° Spitzenwinkel die Leistung des Spiralbohrers? Der 118° Spitzenwinkel des MetavCUT Spiralbohrers erleichtert das Anbohren und sorgt für kontrollierten Vorschub bei üblichen Metallwerkstoffen; bei besonders harten Materialien kann ein größerer Winkel sinnvoll sein, abhängig von der Anwendung. Welche Pflege verlängert die Lebensdauer des MetavCUT Spiralbohrers? Regelmäßiges Entgraten, passende Kühlschmierstoffe bei zähen Werkstoffen und das Vermeiden von Überhitzung während des Bohrens tragen bei dem MetavCUT Spiralbohrer dazu bei, die Schneidkante länger scharf zu halten. {"@context":"https://schema.org","@graph":[{"@type":"Product","@id":"#40099-FDA","sku":"40099-FDA","mpn":"40099-FDA","name":"Spiralbohrer 40099-FDA","description":"Kurzer HSS-Spiralbohrer nach DIN 338, 9,9 mm Durchmesser, Typ N Normalspirale, 118° Spitzenwinkel, schwarz; geeignet für Metallbohrungen an Handbohrmaschinen und für Werkstatt, Montage und DIY-Anwendungen.","image":["https://files.plytix.com/api/v1.1/file/public_files/pim/assets/57/c3/98/62/6298c3575d155f1bc7e497fd/images/8e/48/c5/69/69c5488eb2b3400ba580741c/logo-metav-1200-675.png","https://files.plytix.com/api/v1.1/file/public_files/pim/assets/57/c3/98/62/6298c3575d155f1bc7e497fd/images/8e/48/c5/69/69c5488eb2b3400ba580741b/logo-metav-1200-1200.png","https://files.plytix.com/api/v1.1/file/public_files/pim/assets/57/c3/98/62/6298c3575d155f1bc7e497fd/images/8e/48/c5/69/69c5488eb2b3400ba580741e/logo-metav-1200-900.png"],"additionalProperty":[{"@type":"PropertyValue","name":"Durchmesser","value":"9,9 mm"},{"@type":"PropertyValue","name":"Material","value":"HSS"},{"@type":"PropertyValue","name":"Ausführung","value":"kurz"},{"@type":"PropertyValue","name":"Typ","value":"Typ N (Normalspirale)"},{"@type":"PropertyValue","name":"Spitzenwinkel","value":"118°"},{"@type":"PropertyValue","name":"Farbe","value":"schwarz"},{"@type":"PropertyValue","name":"Gesamtlänge","value":"133 mm"},{"@type":"PropertyValue","name":"Spirallänge","value":"87 mm"},{"@type":"PropertyValue","name":"Norm","value":"DIN 338"},{"@type":"PropertyValue","name":"Für Bohrmaschine","value":"Handbohrmaschine"},{"@type":"PropertyValue","name":"Bezeichnung","value":"Spiralbohrer"},{"@type":"PropertyValue","name":"Hersteller","value":"MetavCUT"}]},{"@type":"FAQPage","mainEntity":[{"@type":"Question","name":"Ist der MetavCUT Spiralbohrer (Typ N) für Handbohrmaschinen geeignet?","acceptedAnswer":{"@type":"Answer","text":"Der MetavCUT Spiralbohrer in kurzer Ausführung wurde für den Einsatz an Handbohrmaschinen konzipiert und bietet durch die reduzierte Auskraglänge erhöhte Stabilität, sodass er sich für typische Werkstattanwendungen in Metall gut eignet."}},{"@type":"Question","name":"Für welche Materialien ist der MetavCUT Spiralbohrer am besten geeignet?","acceptedAnswer":{"@type":"Answer","text":"Der MetavCUT Spiralbohrer (Typ N, HSS) ist besonders geeignet für legierten und unlegierten Stahl, Gusseisen sowie Nichteisenmetalle; weiche Werkstoffe wie Aluminium lassen sich ebenfalls bearbeiten, bei sehr weichen Materialien ist jedoch ein speziellerer Bohrertyp zu prüfen."}},{"@type":"Question","name":"Wie beeinflusst der 118° Spitzenwinkel die Leistung des Spiralbohrers?","acceptedAnswer":{"@type":"Answer","text":"Der 118° Spitzenwinkel des MetavCUT Spiralbohrers erleichtert das Anbohren und sorgt für kontrollierten Vorschub bei üblichen Metallwerkstoffen; bei besonders harten Materialien kann ein größerer Winkel sinnvoll sein, abhängig von der Anwendung."}},{"@type":"Question","name":"Welche Pflege verlängert die Lebensdauer des MetavCUT Spiralbohrers?","acceptedAnswer":{"@type":"Answer","text":"Regelmäßiges Entgraten, passende Kühlschmierstoffe bei zähen Werkstoffen und das Vermeiden von Überhitzung während des Bohrens tragen bei dem MetavCUT Spiralbohrer dazu bei, die Schneidkante länger scharf zu halten."}}]},{"@type":"ItemPage","url":"https://metav-shop.de/produkt/40099-FDA","dateModified":"2026-05-04T12:00:00+01:00","author":{"@type":"Person","name":"Stephan Bayer","url":"https://www.linkedin.com/in/stephan-bayer/"},"publisher":{"@type":"Organization","name":"Metav Werkzeuge GmbH","url":"https://metav-shop.de","logo":{"@type":"ImageObject","url":"https://files.plytix.com/api/v1.1/file/public_files/pim/assets/57/c3/98/62/6298c3575d155f1bc7e497fd/images/8e/48/c5/69/69c5488eb2b3400ba580741c/logo-metav-1200-675.png","width":1200,"height":675},"address":{"@type":"PostalAddress","streetAddress":"Parkring 45","postalCode":"46446","addressLocality":"Emmerich","addressCountry":"DE"},"telephone":"+49 2822 7131930","email":"info@metav-werkzeuge.com"},"about":[{"@type":"Thing","name":"Spiralbohrer Kurz HSS"},{"@type":"Thing","name":"MetavCUT Bohrer"},{"@type":"Thing","name":"DIN 338 Standard"}],"mentions":[{"@type":"Thing","name":"Typ N Normalspirale"},{"@type":"Thing","name":"Handbohrmaschine geeignet"},{"@type":"Thing","name":"HSS Schnellarbeitsstahl"}]}]}

Spiralbohrer kurz HSS-E 9,9 mm · 135° Spitzenwinkel · Typ N · 5% kobaltlegiert · geschliffen · DIN 338 · MetavCUT Der Spiralbohrer ist ein kurzer, geschliffener HSS-E Bohrer zur präzisen Bearbeitung von Metall und bietet hohe Stabilität bei stationären und handgeführten Anwendungen. Kurze Ausführung für verbesserte Stabilität Geschliffen für hohe Rundlaufgenauigkeit 5% kobaltlegiert für bessere Warmfestigkeit 135° Spitzenwinkel für harte Werkstoffe Spirallänge 87 mm bei Gesamtlänge 133 mm Hohe Stabilität und saubere Bohrbilder dank kurzer Bauform Die kurze Ausführung dieses Kurzbohrers reduziert die Auskraglänge und verringert dadurch das Risiko von Verbiegen und Ausschlagen. Durch die erhöhte Steifigkeit entsteht ein gleichmäßigeres Schnittbild und sauberere Bohrlöcher, was besonders bei Stahl und legierten Werkstoffen von Vorteil ist. Anwender profitieren von geringerer Nacharbeit und präziseren Passungen bei Serien- und Einzelteilen. Materialqualität und Schneidcharakteristik für anspruchsvolle Metallbearbeitung Der Bohrer besteht aus HSS-E mit 5% kobaltlegiertem Werkstoff, wodurch sich die Warmfestigkeit und Verschleißbeständigkeit gegenüber normalem Schnellarbeitsstahl verbessert. Die geschliffene Schaft- und Schneidgeometrie sorgt für scharfe Kanten und hohe Rundlaufgenauigkeit, eignet sich daher besonders für präzise Metallbohrungen. Der 135° Spitzenwinkel erleichtert den Anbohrvorgang in harten Stählen und reduziert das Abkippen beim Einschneiden. Vielseitige Einsatzbereiche im Werkstattalltag und bei Montagearbeiten Mit einem Durchmesser von 9,9 mm liegt der Bohrer im Standard-Bereich und ist ideal für Werkstatt, Montage und DIY-Projekte geeignet. Er bearbeitet legierten und unlegierten Stahl, Gusseisen, Nichteisenmetalle und Kunststoffe zuverlässig. Durch die Kombination aus DIN 338 Norm und Typ N Geometrie eignet sich der Bohrer für Handbohrmaschine ebenso wie für stationäre Säulenbohrmaschinen, solange auf passende Kühlschmierstoffe und korrekte Drehzahlen geachtet wird. Anwendungstipps zur Lebensdauer und Prozesssicherheit Vor dem Bohren empfiehlt sich das Anpunkten mit einem Zentrierbohrer zur Verbesserung der Positioniergenauigkeit; bei geschliffenen Bohrern sollte Kühlung eingesetzt werden, um Überhitzung zu vermeiden. Die Spirallänge 87 mm und die Gesamtlänge 133 mm geben Auskunft über Einspanntiefe und Handhabung; der Zylinderschaft erlaubt sicheren Halt im Bohrfutter. Regelmäßiges Entfernen von Spänen und moderate Vorschubgeschwindigkeiten verlängern die Standzeit. MetavCUT empfiehlt den Einsatz dieses geschliffenen HSS-E Kurzbohrers für präzise Metallbohrungen; bei Fragen zur Auswahl oder Anwendung steht METAV Werkzeuge mit technischer Beratung zur Seite – eMail: info@metav-werkzeuge.com, Telefon: +49 2822 7131930, WhatsApp: +49 170 2837271 Bezeichnung: Spiralbohrer kurz HSS-E 9,9 mm, Typ N, geschliffen Marke: MetavCUT SKU: 47099-FDA Durchmesser: 9,9 mm Spitzenwinkel: 135° Material: HSS-E Ausführung: kurz Schaft Ausführung: geschliffen Spirallänge: 87 mm Gesamtlänge: 133 mm Typ: Typ N Norm: DIN 338 Farbe: 5% kobaltlegiert Für Bohrmaschine: Handbohrmaschine Modellserie: Standard Line Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ Welche Werkstoffe bearbeitet der Spiralbohrer von MetavCUT am besten? Der Spiralbohrer von MetavCUT mit HSS-E und 5% kobaltlegiert ist besonders geeignet für legierten und unlegierten Stahl, Gusseisen sowie Nichteisenmetalle und Kunststoffe; bei härteren Werkstoffen sorgt der 135° Spitzenwinkel für stabiles Anbohren. Eignet sich der Spiralbohrer von MetavCUT für die Handbohrmaschine? Ja, der Spiralbohrer von MetavCUT fällt in den Standard-Bereich und kann mit einer Handbohrmaschine verwendet werden; für beste Ergebnisse wird Anpunkten, kontrollierte Drehzahl und Kühlung empfohlen. Warum ist der Spiralbohrer geschliffen und was bedeutet das für den Anwender? Die geschliffene Ausführung des Spiralbohrers von MetavCUT liefert sehr scharfe Schneiden und hohe Rundlaufgenauigkeit, was präzise Bohrlöcher ermöglicht; gleichzeitig sollte auf passende Kühlung und stationäre Spannbedingungen geachtet werden, da geschliffene Bohrer empfindlicher gegenüber Verschleiß und Bruch sein können. Welche Vorteile bietet die 5% Kobaltlegierung beim Spiralbohrer von MetavCUT? Die 5% kobaltlegierte Zusammensetzung des Spiralbohrers von MetavCUT erhöht die Warmfestigkeit und Standzeit bei höheren Schnitttemperaturen, wodurch der Bohrer robuster bei der Bearbeitung von zähen oder legierten Stählen ist. {"@context":"https://schema.org","@graph":[{"@type":"Product","@id":"#47099-FDA","sku":"47099-FDA","mpn":"47099-FDA","name":"Spiralbohrer 47099-FDA","description":"Kurzer Spiralbohrer HSS-E 9,9 mm, 135° Spitzenwinkel, Typ N, 5% kobaltlegiert, geschliffen, DIN 338; Kurzbohrerausführung für präzise Metallbearbeitung mit hoher Stabilität und Rundlaufgenauigkeit.","image":["https://files.plytix.com/api/v1.1/file/public_files/pim/assets/57/c3/98/62/6298c3575d155f1bc7e497fd/images/8e/48/c5/69/69c5488eb2b3400ba580741b/logo-metav-1200-1200.png","https://files.plytix.com/api/v1.1/file/public_files/pim/assets/57/c3/98/62/6298c3575d155f1bc7e497fd/images/8e/48/c5/69/69c5488eb2b3400ba580741e/logo-metav-1200-900.png","https://files.plytix.com/api/v1.1/file/public_files/pim/assets/57/c3/98/62/6298c3575d155f1bc7e497fd/images/8e/48/c5/69/69c5488eb2b3400ba580741c/logo-metav-1200-675.png"],"additionalProperty":[{"@type":"PropertyValue","name":"Bezeichnung","value":"Spiralbohrer kurz HSS-E 9,9 mm, Typ N, geschliffen"},{"@type":"PropertyValue","name":"Durchmesser","value":"9,9 mm"},{"@type":"PropertyValue","name":"Spitzenwinkel","value":"135°"},{"@type":"PropertyValue","name":"Typ","value":"Typ N"},{"@type":"PropertyValue","name":"Farbe","value":"5% kobaltlegiert"},{"@type":"PropertyValue","name":"Ausführung","value":"kurz"},{"@type":"PropertyValue","name":"Norm","value":"DIN 338"},{"@type":"PropertyValue","name":"Material","value":"HSS-E"},{"@type":"PropertyValue","name":"Schaft Ausführung","value":"geschliffen"},{"@type":"PropertyValue","name":"Spirallänge","value":"87 mm"},{"@type":"PropertyValue","name":"Gesamtlänge","value":"133 mm"},{"@type":"PropertyValue","name":"Für Bohrmaschine","value":"Handbohrmaschine"},{"@type":"PropertyValue","name":"Modellserie","value":"Standard Line"},{"@type":"PropertyValue","name":"Hersteller","value":"MetavCUT"}],"brand":null},{"@type":"FAQPage","mainEntity":[{"@type":"Question","name":"Welche Werkstoffe bearbeitet der Spiralbohrer am besten?","acceptedAnswer":{"@type":"Answer","text":"Der Spiralbohrer kurz HSS-E 9,9 mm von MetavCUT mit 5% kobaltlegiert eignet sich besonders für legierten und unlegierten Stahl, Gusseisen, Nichteisenmetalle und Kunststoffe; der 135° Spitzenwinkel erleichtert das Anbohren härterer Werkstoffe."}},{"@type":"Question","name":"Eignet sich der Spiralbohrer für die Handbohrmaschine?","acceptedAnswer":{"@type":"Answer","text":"Ja, der Spiralbohrer kurz HSS-E 9,9 mm von MetavCUT ist für Handbohrmaschine geeignet; für beste Ergebnisse empfiehlt sich Anpunkten, kontrollierte Drehzahl und Kühlung."}},{"@type":"Question","name":"Was bedeutet geschliffen beim Spiralbohrer und welche Folgen hat das?","acceptedAnswer":{"@type":"Answer","text":"Geschliffen bedeutet, dass Spannuten und Geometrie per CNC geschliffen sind; das liefert sehr scharfe Schneiden und hohe Rundlaufgenauigkeit, erfordert aber Kühlung und schonende Handhabung, da geschliffene Bohrer spröder sein können."}},{"@type":"Question","name":"Welche Vorteile bringt die 5% Kobaltlegierung beim Spiralbohrer?","acceptedAnswer":{"@type":"Answer","text":"Die 5% kobaltlegiert Zusammensetzung erhöht die Warmfestigkeit und Standzeit bei höheren Schnitttemperaturen, wodurch der Spiralbohrer von MetavCUT robuster bei der Bearbeitung zäher oder legierter Stähle ist."}}]},{"@type":"ItemPage","url":"https://metav-shop.de/47099-FDA","dateModified":"2026-05-04T12:00:00+01:00","author":{"@type":"Person","name":"Stephan Bayer","url":"https://www.linkedin.com/in/stephan-bayer/"},"publisher":{"@type":"Organization","name":"Metav Werkzeuge GmbH","url":"https://metav-shop.de","logo":{"@type":"ImageObject","url":"https://files.plytix.com/api/v1.1/file/public_files/pim/assets/57/c3/98/62/6298c3575d155f1bc7e497fd/images/8e/48/c5/69/69c5488eb2b3400ba580741c/logo-metav-1200-675.png","width":1200,"height":675},"address":{"@type":"PostalAddress","streetAddress":"Parkring 45","postalCode":"46446","addressLocality":"Emmerich","addressCountry":"DE"},"telephone":"+49 2822 7131930","email":"info@metav-werkzeuge.com"},"about":[{"@type":"Thing","name":"Spiralbohrer kurz HSS-E"},{"@type":"Thing","name":"DIN 338 Norm"},{"@type":"Thing","name":"MetavCUT Standard Line"}],"mentions":[{"@type":"Thing","name":"Geschliffene Schaftgeometrie"},{"@type":"Thing","name":"5% Kobaltlegierung"},{"@type":"Thing","name":"135° Spitzenwinkel für harte Werkstoffe"},{"@type":"Thing","name":"Zylinderschaft"}]}]}

Twist Drill — Type N, 9.9 mm, 135° tip, short, bright finished, HSS‑G, DIN 338 (MetavCUT) The Twist Drill Type N is a short HSS‑G drill for precision metal drilling, designed for use in hand and machine drilling applications. Short design for improved stability 135° tip for hard materials HSS‑G fully ground for precise holes Conforms to DIN 338 for metalworking Precision and performance for demanding metalwork Designed for accurate metal drilling, this HSS‑G short Twist Drill delivers consistently clean holes with high roundness. The fully ground geometry produces very sharp cutting edges and excellent runout characteristics, which reduces burr formation and improves hole quality. For users seeking reliable results in alloyed and unalloyed steels, the combination of Type N spiral and a 135° point angle supports controlled penetration and reduces lateral wandering during the initial drill entry. Short length for stability and faster operation Because the bit has a reduced protruding length, the short design significantly increases rigidity and lowers the tendency to bend under load. This leads to measurable workflow benefits: the grinded HSS geometry enables drilling up to 40% faster while requiring 50% less feed force compared with conventional HSS variants. Contractors and workshop technicians working on small setups or clamped workpieces profit from improved precision and less chatter when using a compact, robust drill of this design. Geometry and materials optimised for hard materials The 135° tip angle is chosen specifically to assist drilling into harder materials such as stainless steel and tempered components; a larger point angle shortens initial bite time while maintaining tool life. The designation DIN 338 classifies this short Twist Drill with a cylindrical shank and describes the ground manufacturing process; grinding (HSS‑G) creates sharp cutting lips but can make the tool more brittle, so coolant and steady machine setup are advisable to avoid premature breakage. Who benefits and practical usage advice This Twist Drill is targeted at professional users and advanced hobbyists needing reliable metal drilling — especially for precision work on lathe‑mounted or stationary drilling machines and well‑supported handheld drilling operations. The fully ground shank ensures good chucking accuracy; for best results, secure the workpiece, use appropriate cutting fluid and moderate feed, and avoid excessive overhang. MetavCUT’s short series is particularly suitable when stability and accuracy are priorities over reach. Strongly recommended: choose the MetavCUT short HSS‑G Twist Drill Type N for demanding metal applications — for personalised technical advice and ordering support contact METAV Werkzeuge at info@metav-werkzeuge.com, call +49 2822 7131930 or message via WhatsApp +49 170 2837271 Designation: Twist Drill Brand: MetavCUT SKU: 45099-FDA Diameter: 9.9 mm Tip angle: 135° Type: Type N Execution: Short Colour: Bright finished Material: HSS‑G Shank finish: Fully ground Spiral length: 87 mm Overall length: 133 mm For drill machine: Drilling Machine (Hand drill) Model series: Standard Line Norm: DIN 338 Application: Drills for metal Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What are Twist Drills used for and which materials suit them best? The MetavCUT Twist Drill Type N is primarily used for drilling metal; it is especially effective on alloyed and unalloyed steels, cast materials and non‑ferrous metals. Its geometry and 135° point make it suitable for harder workpieces where accurate centring and reduced walking are required. Which three drill types are commonly distinguished? In general practice three main categories are identified: metal drills, wood drills and stone/concrete drills. The MetavCUT Twist Drill Type N belongs to the metal drill group and is optimised for machining metallic materials. Can the MetavCUT Twist Drill be used in a handheld drill or only in machine tools? The short design of the MetavCUT Twist Drill Type N improves rigidity and makes it suitable for both well‑supported handheld drilling and stationary machine tools; however, optimum precision is achieved in clamped or machine setups with appropriate cooling. Why is the tip of a Twist Drill ground to a specific angle? The 135° tip on the MetavCUT Twist Drill reduces initial cutting forces and improves centring in hard materials; grinding the tip also reduces the cross‑cut width, lowering friction and the required feed, which helps achieve cleaner holes with less tool wear.

Spiralbohrer kurz Ø 9,9 mm, 135°, Typ N, blank, geschliffen, DIN 338, HSS-G von MetavCUT Der Spiralbohrer ist ein kurzer HSS-G Metallbohrer für präzise Bohrungen in Stahl und Gusswerkstoffen und eignet sich für Handbohrmaschinen und stationäre Maschinen. Kurze Ausführung für höhere Stabilität Geschliffene Geometrie für saubere Bohrbilder 135° Spitzenwinkel für harte Werkstoffe DIN 338 Norm für kurze Spiralbohrer Geeignet für Handbohrmaschine und stationären Einsatz Mehr Präzision und Standfestigkeit bei Metallbohrungen Die kurze Ausführung des Bohrers sorgt durch die reduzierte Auskraglänge für deutlich höhere Stabilität und weniger Verformung beim Einspannvorgang. Dank der geschliffenen Fertigung (HSS-G) bietet die Schneidkante hohe Schärfe und exzellenten Rundlauf, was zu sauberen, maßhaltigen Bohrlöchern führt. Diese Kombination reduziert Vibrationen und erhöht die Sicherheit bei der Bearbeitung von legiertem und unlegiertem Stahl. Für Anwendungen, bei denen Maßhaltigkeit und Oberflächenqualität zählen, ist diese Konstruktion klar im Vorteil. Schneller bohren mit weniger Kraftaufwand Der spezielle Schnittwinkel und die gehaltvolle HSS-G-Werkstoffausführung ermöglichen ein bis zu 40 % schnelleres Bohren bei gleichzeitig 50 % weniger Anpresskraft im Vergleich zu herkömmlichen HSS-Bohrern. Der 135° Spitzenwinkel reduziert die Anbohrzeit in harten Werkstoffen und minimiert das Auslaufen der Bohrung bei dünnen Blechen. Dadurch wird der Arbeitsfluss effizienter und die Belastung für Maschine und Bediener sinkt, was besonders in Serien- und Montageumgebungen von Vorteil ist. Für anspruchsvolle Werkstätten und vielfältige Metallanwendungen Der Bohrer wurde nach DIN 338 als kurzer Spiralbohrer mit Zylinderschaft konstruiert und ist als Typ N mit Normalspirale optimal für das Bohren von Stahl, Gusseisen, Temperguss und Nichteisenmetallen ausgelegt. Die kurze Gesamtlänge reduziert die Bruchgefahr bei handgeführten Maschinen, erlaubt aber zugleich den Einsatz an stationären Bohrmaschinen. Durch die robuste Materialwahl eignet sich das Werkzeug auch für anspruchsvolle Werkstätten, die auf Wiederholgenauigkeit und lange Standzeiten Wert legen. Einsatzhinweise und Praxisvorteile Beim Bohren in dickeren oder sehr harten Werkstoffen empfiehlt sich eine angepasste Drehzahl und die Verwendung von Kühlschmierstoff, um die Lebensdauer des Bohrers zu erhöhen. Die geschliffene Ausführung liefert sehr scharfe Spannuten und saubere Spanabfuhr, weshalb bei geeigneter Kühlung auch höhere Schnittgeschwindigkeiten möglich sind. Das Produkt ist speziell für Metallbearbeitung ausgelegt und reduziert durch seine Geometrie Nacharbeit und Gratbildung. Entscheiden Sie sich für den MetavCUT Spiralbohrer als verlässliches Präzisionswerkzeug für Ihre Metallbearbeitung; bei technischen Fragen oder Auswahlhilfe steht METAV Werkzeuge gern mit Beratung per eMail info@metav-werkzeuge.com oder Telefon +49 2822 7131930 zur Verfügung. Bezeichnung: Spiralbohrer Marke: MetavCUT SKU: 48099-FDA Durchmesser: 9,9 mm Spitzenwinkel: 135° Typ: Typ N Farbe: blank Ausführung: kurz Material: HSS-G Schaft Ausführung: geschliffen Gesamtlänge: 133 mm Spirallänge: 87 mm Norm: DIN 338 Für Bohrmaschine: Handbohrmaschine Modellserie: Profi Line Verpackungseinheit: 5 Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ Ist der Spiralbohrer von MetavCUT für Handbohrmaschinen geeignet? Der Spiralbohrer von MetavCUT ist durch seine kurze Ausführung und die Zylinderschaft speziell für den Einsatz in Handbohrmaschinen sowie in stationären Maschinen ausgelegt und bietet dabei stabile Führungswerte. Für welche Werkstoffe eignet sich der Spiralbohrer Typ N von MetavCUT am besten? Der Spiralbohrer der Marke MetavCUT (Typ N) wurde primär für Stahl, Gusseisen, Temperguss und Nichteisenmetalle entwickelt und liefert bei diesen Werkstoffen besonders saubere Bohrbilder. Wie beeinflusst der 135° Spitzenwinkel die Bohrleistung des MetavCUT Spiralbohrers? Der Spiralbohrer mit 135° Spitzenwinkel von MetavCUT bietet eine reduzierte Anbohrzeit und bessere Zentrierung in harten Werkstoffen, wodurch die Effizienz beim Bohren von Edelstahl und gehärteten Stählen steigt. Brauche ich beim Einsatz des MetavCUT Spiralbohrers Kühlung? Bei intensiven oder tieferen Bohrungen in harten Materialien empfiehlt es sich, den Spiralbohrer von MetavCUT mit Kühlschmierstoff zu betreiben, um Standzeit und Schneidleistung zu erhalten und die Bruchgefahr zu minimieren. {"@context":"https://schema.org","@graph":[{"@type":"Product","@id":"#48099-FDA","sku":"48099-FDA","mpn":"48099-FDA","name":"Spiralbohrer 48099-FDA","description":"Kurz ausgeführter Spiralbohrer Ø 9,9 mm, 135° Spitzenwinkel, Typ N, blank, geschliffen, DIN 338, HSS-G; entwickelt für präzise Metallbohrungen in Stahl, Gusseisen, Temperguss und Nichteisenmetallen; geeignet für Handbohrmaschine und stationäre Maschinen; hohe Stabilität durch kurze Auskraglänge; geschliffene Geometrie für saubere Bohrbilder.","image":["https://files.plytix.com/api/v1.1/file/public_files/pim/assets/57/c3/98/62/6298c3575d155f1bc7e497fd/images/8e/48/c5/69/69c5488eb2b3400ba580741b/logo-metav-1200-1200.png","https://files.plytix.com/api/v1.1/file/public_files/pim/assets/57/c3/98/62/6298c3575d155f1bc7e497fd/images/8e/48/c5/69/69c5488eb2b3400ba580741e/logo-metav-1200-900.png","https://files.plytix.com/api/v1.1/file/public_files/pim/assets/57/c3/98/62/6298c3575d155f1bc7e497fd/images/8e/48/c5/69/69c5488eb2b3400ba580741c/logo-metav-1200-675.png"],"about":[{"@type":"Thing","name":"Spiralbohrer kurz Ø 9,9 mm"},{"@type":"Thing","name":"DIN 338 kurze Spiralbohrer mit Zylinderschaft"},{"@type":"Thing","name":"HSS-G geschliffene Geometrie"}],"mentions":[{"@type":"Thing","name":"Einsatz: Stahl, Gusseisen, Temperguss, Nichteisenmetalle"},{"@type":"Thing","name":"Vorteile: höhere Stabilität, saubere Bohrbilder, reduzierte Anpresskraft"},{"@type":"Thing","name":"Empfohlen: Kühlmittel bei hartem Material"}],"additionalProperty":[{"@type":"PropertyValue","name":"Bezeichnung","value":"Spiralbohrer"},{"@type":"PropertyValue","name":"Marke","value":"MetavCUT"},{"@type":"PropertyValue","name":"Durchmesser","value":"9,9 mm"},{"@type":"PropertyValue","name":"Spitzenwinkel","value":"135°"},{"@type":"PropertyValue","name":"Typ","value":"Typ N"},{"@type":"PropertyValue","name":"Farbe","value":"blank"},{"@type":"PropertyValue","name":"Ausführung","value":"kurz"},{"@type":"PropertyValue","name":"Material","value":"HSS-G"},{"@type":"PropertyValue","name":"Schaft Ausführung","value":"geschliffen"},{"@type":"PropertyValue","name":"Gesamtlänge","value":"133 mm"},{"@type":"PropertyValue","name":"Spirallänge","value":"87 mm"},{"@type":"PropertyValue","name":"Norm","value":"DIN 338"},{"@type":"PropertyValue","name":"Für Bohrmaschine","value":"Handbohrmaschine"},{"@type":"PropertyValue","name":"Modellserie","value":"Profi Line"},{"@type":"PropertyValue","name":"Verpackungseinheit","value":"5"},{"@type":"PropertyValue","name":"Anwendung","value":"Bohrer für Metall"},{"@type":"PropertyValue","name":"Leistungsmerkmal","value":"bis zu 40 % schnelleres Bohren, 50 % weniger Anpresskraft im Vergleich zu herkömmlichen HSS-Bohrern"}]},{"@type":"FAQPage","mainEntity":[{"@type":"Question","name":"Ist der Spiralbohrer von MetavCUT für Handbohrmaschinen geeignet?","acceptedAnswer":{"@type":"Answer","text":"Der Spiralbohrer von MetavCUT ist durch die kurze Ausführung und den Zylinderschaft speziell für den Einsatz in Handbohrmaschinen sowie in stationären Maschinen ausgelegt und bietet stabile Führungswerte."}},{"@type":"Question","name":"Für welche Werkstoffe eignet sich der Spiralbohrer Typ N von MetavCUT am besten?","acceptedAnswer":{"@type":"Answer","text":"Der Spiralbohrer MetavCUT Typ N ist primär für Stahl, Gusseisen, Temperguss und Nichteisenmetalle konzipiert und liefert bei diesen Werkstoffen besonders saubere Bohrbilder."}},{"@type":"Question","name":"Wie beeinflusst der 135° Spitzenwinkel die Bohrleistung des MetavCUT Spiralbohrers?","acceptedAnswer":{"@type":"Answer","text":"Der 135° Spitzenwinkel des MetavCUT Spiralbohrers reduziert die Anbohrzeit und verbessert die Zentrierung in harten Werkstoffen, was die Effizienz beim Bohren von Edelstahl und gehärteten Stählen erhöht."}},{"@type":"Question","name":"Brauche ich beim Einsatz des MetavCUT Spiralbohrers Kühlung?","acceptedAnswer":{"@type":"Answer","text":"Bei intensiven oder tieferen Bohrungen in harten Materialien empfiehlt sich die Verwendung von Kühlschmierstoff, um Standzeit und Schneidleistung des MetavCUT Spiralbohrers zu erhöhen und die Bruchgefahr zu minimieren."}}]},{"@type":"ItemPage","url":"https://metav-shop.de/produkt/48099-FDA","dateModified":"2026-05-04T12:00:00+01:00","author":{"@type":"Person","name":"Stephan Bayer","url":"https://www.linkedin.com/in/stephan-bayer/"},"publisher":{"@type":"Organization","name":"Metav Werkzeuge GmbH","url":"https://metav-shop.de","logo":{"@type":"ImageObject","url":"https://files.plytix.com/api/v1.1/file/public_files/pim/assets/57/c3/98/62/6298c3575d155f1bc7e497fd/images/8e/48/c5/69/69c5488eb2b3400ba580741c/logo-metav-1200-675.png","width":1200,"height":675},"address":{"@type":"PostalAddress","streetAddress":"Parkring 45","postalCode":"46446","addressLocality":"Emmerich","addressCountry":"DE"},"telephone":"+49 2822 7131930","email":"info@metav-werkzeuge.com"}}]}

Twist Drill — Type N short, Ø 9 mm, 118° tip, black, HSS, DIN 338 (MetavCUT) The Twist Drill Type N short is a high‑stability HSS metal drill designed for precise holemaking in steel and other metals with a 9 mm diameter and a 118° tip angle. Short HSS design for enhanced stiffness 9 mm diameter for standard metal holes 118° tip for reliable centering Complies with DIN 338 for short twist drills Black finish for corrosion resistance Precision and durability from HSS material High Speed Steel (HSS) gives this Twist Drill outstanding elasticity and resistance to fracture during common metalworking tasks. The HSS composition is especially suitable for drilling alloyed and unalloyed steel, cast iron, non‑ferrous metals and plastics, providing dependable tool life under typical workshop conditions. The short execution reduces flex and vibration, resulting in consistently round holes and longer tool service intervals. Better control and centering with a 118° tip A 118° point angle improves centering on curved or slightly irregular surfaces and reduces walking at the drill start, which is useful when producing clean, accurate holes in softer steels and aluminium. Because the tip geometry affects feed forces and heat generation, this configuration balances penetration speed and control for general metalworking. Users benefit from fewer re‑drills and faster set‑up when precision is required. Stable short design according to DIN 338 Manufactured to DIN 338, the short twist drill format prioritises stiffness and dimensional accuracy. This Type N short design minimizes overhang from the chuck, lowering the risk of bending and enabling higher feed rates on both portable and stationary drilling machines. MetavCUT’s adherence to this standard means predictable performance and interchangeability with other DIN‑compliant tooling in professional environments. Practical use recommendations for workshop and on‑site work When using this MetavCUT Twist Drill in a drilling machine or a hand drill, moderate cutting speeds and steady feed ensure optimal results; excessive speed can shorten tool life. For holes up to moderate depths, the short overall length (125 mm) and spiral length (81 mm) improve chip evacuation and reduce runout. Professionals and serious hobbyists will appreciate the combination of robustness and ease of resharpening that HSS tools offer. Highly recommended: For precise metal drilling choose the MetavCUT Twist Drill Type N short in HSS for reliable centering and enhanced stiffness — for personalised technical advice METAV Werkzeuge provides expert consultation via eMail: info@metav-werkzeuge.com, Phone: +49 2822 7131930 or WhatsApp: +49 170 2837271 Designation: Twist Drill Brand: MetavCUT SKU: 40090-FDA Diameter: 9 mm Point angle: 118° Type: Type N Colour: black Version: short Material: HSS Standard: DIN 338 Spiral length: 81 mm Overall length: 125 mm Application: Drills for metal For use with: Drilling Machine / Hand Drill Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What is the MetavCUT Twist Drill Type N short best used for? The MetavCUT Twist Drill Type N short is intended primarily for drilling metal; it excels in producing accurate holes in alloyed and unalloyed steel, cast iron and non‑ferrous metals thanks to its HSS construction and short, stiff geometry. Can this Twist Drill be used in a hand drill? Yes, the MetavCUT Twist Drill short execution can be used in a hand drill or a drilling machine, but best results come from steady speeds and controlled feed to maintain centering and to avoid excessive wear. What are Twist Drills used for? Twist Drills are mainly applied when machining high‑strength materials and larger diameters. Their form allows straightforward resharpening and sustains higher loads; the design suits metalworking and larger bore tasks. Which three drill types exist? There are three principal drill types: Metal drills, Wood drills and Stone/Concrete drills.

Twist Drill – Short HSS‑E Type N, Ø 9 mm, 135°, 5% Cobalt‑Alloyed, DIN 338 (MetavCUT) The Twist Drill from MetavCUT is a short Type N drill for precise metalworking, especially suited to drilling hard and alloyed steels with a 135° tip angle. Short design for high stability 135° tip for hard materials Fully ground flutes for precise holes HSS‑E with 5% cobalt for heat resistance Conforms to DIN 338 for short drills Greater Precision through Short Design and Material Choice The short Execution reduces overhang and increases Stability, which is particularly beneficial when machining hard metals. Manufactured in HSS‑E with 5% Cobalt‑Alloyed composition, the tool offers improved heat resistance and wear behaviour compared with standard HSS. As a result, operators achieve cleaner holes and longer tool life when performing demanding Metalworking tasks on stationary or portable Drilling Machines. Clean Holes and High Runout Accuracy with Ground Geometry A Fully ground flute geometry produces very sharp cutting edges and excellent Runout Accuracy, ideal for precision applications. The Type N spiral geometry is the classic choice for Metal Drilling and generates reliable chip evacuation in many alloys. Note that ground drills can be more brittle than rolled variants, therefore using appropriate cooling and careful feed rates on tougher Materials is recommended to avoid breakage. Designed for Metalworking: Recommended Applications and Users This MetavCUT Twist Drill is intended for drilling Alloyed and Unalloyed Steel, Cast Iron, Non‑Ferrous Metals and certain Plastics; it is well suited to workshop technicians, maintenance teams and precision machinists. The short overall length and stable shank make it especially useful for operations requiring minimal deflection, such as jig and fixture work or when using a Hand Drill for controlled site repairs. 135° Point Angle: Faster Penetration and Better Centering in Hard Materials A 135° Point Angle helps reduce the tendency to wander on the surface of hard materials and shortens the initial penetration time compared with steeper points. This geometry lowers the cutting forces on the central tip and improves centring on Stainless Steel and other tough alloys, enabling more dependable starts and reducing the need for pilot operations in many cases. Standard Compliance and Practical Handling Notes Conforming to DIN 338 ensures consistent dimensions and interchangeability for short Twist Drills with cylindrical shank. The Standard Line manufacturing and the Fully Ground Shaft Execution ensure predictable performance across batches. For best results, pair the drill with appropriate coolant and moderate spindle speeds when working in high‑tensile steels; this preserves edge integrity and reduces the risk of chipping. Strong recommendation: choose the MetavCUT Twist Drill (Short Type N, HSS‑E) for demanding metal drilling tasks — for tailored advice or supplementary technical data contact METAV Werkzeuge by eMail: info@metav-werkzeuge.com, Tel: +49 2822 7131930, WhatsApp: +49 170 2837271 Technical Information Designation: Twist Drill Brand: MetavCUT SKU: 47090-FDA Diameter: 9 mm Point angle: 135° Type: Type N Execution: Short Colour: 5% cobalt-alloyed Material: HSS‑E Shaft execution: Fully ground Overall length: 125 mm Spiral length: 81 mm Model series: Standard Line Norm: DIN 338 For drilling machine: Drilling Machine (Hand Drill) Application: Drills for metal Packaging unit: 5 Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What are Twist Drills used for? The MetavCUT Twist Drill (Type N) is primarily used for machining high‑strength materials and larger drill diameters; its geometry allows straightforward regrinding and it withstands greater mechanical loads, making it a standard choice for robust Metalworking tasks. Which three drill types exist? Common categories are Metal drills, Wood drills and Stone/Concrete drills, and the MetavCUT Twist Drill belongs to the Metal drill group suited for ferrous and non‑ferrous Materials. Can the MetavCUT Twist Drill be used for wood? The MetavCUT Twist Drill can be used in Wood, but as a Metal drill it offers less guidance and a rougher finish than dedicated Wood drills; it is easier to resharpen and shows lower self‑feeding tendency compared with specialised wood brad point drills.

Twist Drill by MetavCUT — 9 mm, 135° Tip, Extra Long, Bright Finished, HSS‑G, DIN 1869, Fully Ground Shank A Twist Drill designed for deep metal drilling with Drilling Machines and engineered for high precision and reduced feed force. Extra long design for deep drilling HSS‑G ground for faster metal cutting 135° tip geometry for hard materials Fully ground shank for high runout accuracy Conforms to DIN 1869 for demanding applications Faster drilling with lower feed force for efficient workflows The HSS‑G construction delivers up to 40% faster drilling while requiring 50% less feed force compared with conventional HSS drills, making it ideal where productivity matters. Designed as an extra long variant, this drill enables deeper hole depths and greater reach without sacrificing concentricity. For workshop and industrial use, the combination of high cutting speed and reduced operator exertion translates into measurable time savings and less operator fatigue. Reliable centring and clean holes even in tough alloys With a 135° tip angle and a ground flute geometry, this tool penetrates harder materials more effectively and reduces walking at the start of the hole. The CNC ground flutes provide sharp cutting edges and excellent runout accuracy, resulting in precise, burr‑reduced holes in Grauguss, legierten and unlegierten Stahl, and non‑ferrous metals. The geometry is optimised to support drilling in applications up to the material classes indicated by DIN 1869. Built for deep and difficult penetrations The extended overall length and a spiral length of 175 mm allow drilling where standard lengths fail, for example deep assemblies or awkward fixturing. The bright finished surface offers good chip evacuation characteristics in conjunction with appropriate coolant, while the fully ground shank ensures consistent clamping in chucks and reduced vibration. Use with a suitable Drilling Machine and controlled coolant flow for best results in prolonged or stationary operations. Who benefits and how to use it correctly Manufacturers, toolrooms and maintenance teams that require repeatable, precise holes in harder metals will value this design. For optimal life and performance, use stable fixturing, appropriate spindle speeds and coolant when working with high‑strength steels. Because ground HSS drills can be more brittle than rolled types, avoid excessive lateral loading and prefer stationary machine setups for deepest holes and continuous production runs. Strong recommendation: Choose the MetavCUT Twist Drill for precise deep‑hole metalworking — for technical advice or to confirm suitability for a specific application, contact METAV Werkzeuge for expert support via email info@metav-werkzeuge.com, phone +49 2822 7131930 or WhatsApp +49 170 2837271 Technical specifications Designation: Twist Drill Brand: MetavCUT SKU: 32090-FDA Diameter: 9 mm Tip Angle: 135° Execution: Extra long Total Length: 250 mm Spiral Length: 175 mm Material: HSS‑G Shank Execution: Fully ground Colour: Bright finished Application: Drills for metal For Drilling Machine: Drilling Machine Standard: DIN 1869 Model Series: Standard Line Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What is a Twist Drill used for and which materials suit this MetavCUT Twist Drill? The MetavCUT Twist Drill is primarily intended for drilling into metals; its HSS‑G composition and 135° tip make it especially suitable for alloyed and unalloyed steels, cast iron and non‑ferrous metals. Use in a properly set up Drilling Machine with cooling for best results. Which three general drill types exist? The three main drill categories are metal drills, wood drills, and stone/concrete drills; the MetavCUT Twist Drill belongs to the metal drill group and is optimised for metalworking tasks.

Twist Drill — Twist Drill, Diameter 9 mm, 135° Tip, Extra Long, Bright Finished, HSS‑G, DIN 1869 The Twist Drill is an extra‑long HSS‑G drill bit for drilling machines, designed for deep metal drilling and precise holemaking in alloyed and unalloyed steels. Extra long design for deep drilling 9 mm diameter with 135° tip angle HSS‑G fully ground for precise bores Conforms to DIN 1869 for deep‑hole work Precision and material: ground HSS for clean metal holes The fully ground HSS‑G geometry delivers high concentricity and sharp cutting edges, producing clean, precise holes in metal. Grinding the flutes rather than rolling creates a sharper cutting profile, which reduces chatter and improves roundness when used with appropriate feed and coolant. This makes the bit particularly suitable for alloyed and unalloyed steel, cast iron and non‑ferrous metals where hole quality and dimensional accuracy are required. Deep drilling capability: extra length for difficult access With an extra long overall length and an extended spiral, this design allows drilling in deep parts or where access from the rear is restricted. The extended spiral assists chip evacuation during deeper cuts, reducing the risk of clogging. For tasks requiring long reach, the extra‑long execution provides the working length necessary without compromising guidance when used in a suitable drilling machine and with correct cooling. Tip geometry and performance: 135° for harder materials A 135° tip angle reduces the tendency to wander and shortens centring time on harder workpieces such as stainless steel. The larger tip angle reduces the aggressiveness of the lead, distributing cutting forces over a broader area and often requiring less feed force. For demanding materials, the combination of tip geometry and HSS‑G composition improves tool life when adequate coolant and a stable setup are used. Practical use and user group: suited for workshops and industrial settings This twist drill was developed for professional workshops and industrial users who need reliable deep drilling in metals. It is best applied in drilling machines under steady clamping and with cooling. Compared with rolled types, the ground version can be re‑sharpened more easily to renew cutting edges, making it advantageous for users who perform maintenance on tooling and value reproducibility and finish. Strong recommendation: Choose the MetavCUT Twist Drill in extra‑long HSS‑G execution for demanding deep metal drilling — for technical advice or to confirm suitability for a specific application, METAV Werkzeuge provides expert consultation: info@metav-werkzeuge.com, Phone +49 2822 7131930, WhatsApp +49 170 2837271 Designation: Twist Drill Brand: MetavCUT SKU: 33090-FDA Diameter: 9 mm Tip Angle: 135° Execution / Type: Extra Long Colour: Bright Finished Material: HSS‑G Shaft Execution: Fully Ground Spiral Length: 220 mm Overall Length: 320 mm Standard: DIN 1869 Application: Drills for Metal Model Series: Standard Line For Use In: Drilling Machine Manufacturer: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What is the MetavCUT Twist Drill used for? The MetavCUT Twist Drill is primarily applied for drilling high‑strength workpieces and larger diameters in metal; its extra‑long HSS‑G design and DIN 1869 specification make it suitable for deep drilling where extended reach and durable cutting performance are required. Which three drill types exist? Common categories are Metal drills, Wood drills and Masonry/Concrete drills; the MetavCUT Twist Drill belongs to the metal drill category and is optimised for metalworking tasks. For what is a Twist Drill mainly used? A Twist Drill is mainly used for machining high‑strength materials and larger hole diameters; its form allows straightforward resharpening and it withstands higher loads in demanding applications. Why are twist drills pointed? The point reduces the cross‑edge at the tip of the Twist Drill, significantly lowering friction and feed forces while improving centring in the workpiece; a pointed geometry therefore eases penetration and enhances accuracy.

Twist Drill — Extra Long Twist Drill, 9 mm, 135° tip, HSS‑G, Bright Finished (MetavCUT) The Twist Drill is an extra‑long HSS‑G drill designed for deep metal drilling with a 9 mm diameter and a 135° tip for hard materials. Extra‑long design for deep, hard‑to‑reach holes 9 mm Diameter for precise metal drilling 135° Tip angle optimised for harder materials HSS‑G ground for fast, clean cuts DIN 1869 compliant for demanding deep‑hole work Precision and performance for deep metal holes The MetavCUT extra‑long HSS‑G twist drill combines a generous overall length with a long Spiral to enable deep‑reach drilling where standard lengths fall short. Thanks to the fully ground flute geometry, the bit produces very sharp cutting edges and high run‑out accuracy, which results in cleaner, more precise holes in metals. For workshop and industrial environments this means fewer re‑cuts, improved fit‑up of components and more predictable machining results under challenging conditions. Faster cutting with less feed force The ground HSS‑G material and optimised geometry allow up to 40% faster drilling and require up to 50% less feed force compared with conventional HSS drills. This makes the tool especially effective when working with alloyed and unalloyed steel, cast steel, cast iron and non‑ferrous metals. The 135° tip angle reduces initial cutting resistance and improves centring on harder materials, shortening set‑up time and increasing throughput on serial operations. Reliable choice for demanding standards and deep drilling Conforming to DIN 1869, this twist drill is built for deep‑hole applications and tougher conditions. The Spiral length of 280 mm and total length of 410 mm are tailored for situations that require extended reach without compromising hole quality. Because the flutes are formed by CNC grinding rather than rolling, users benefit from superior surface finish and dimensional accuracy—features that matter when subsequent machining or assembly demands tight tolerances. Practical workshop guidance and safe use When using this extra‑long Twist Drill in tougher materials, stationary mounting and adequate cooling are recommended to avoid brittle fracture and to extend tool life. The fully ground shank supports better clamping accuracy in chucks and collets, reducing vibration and ensuring concentricity. For operators less familiar with deep‑hole techniques, using modest spindle speeds, steady feed and cutting fluid will deliver the best balance between speed and tool life. Who benefits from this tool This drill is aimed at metalworkers, toolrooms and maintenance professionals who require extended reach and high‑quality holes in harder materials. Whether producing components in small series or performing repair work on assemblies where access is limited, the MetavCUT twist drill offers a practical combination of depth capability and metal‑cutting performance. Strongly recommended: the MetavCUT extra‑long HSS‑G Twist Drill for reliable deep metal drilling — for technical advice or application support contact METAV Werkzeuge; we provide comprehensive consultation and sample guidance via eMail: info@metav-werkzeuge.com, Phone: +49 2822 7131930, WhatsApp: +49 170 2837271 Technical data Designation: Twist Drill Brand: MetavCUT Model series: Standard Line Diameter: 9 mm Total length: 410 mm Spiral length: 280 mm Tip angle: 135° Material: HSS‑G Standard: DIN 1869 Execution: Extra long Colour: Bright finished Shaft finish: Fully ground Suitable for: Drilling Machine / Hand drill Application: Drills for metal Manufacturer: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What materials is the MetavCUT Twist Drill best suited for? The MetavCUT Twist Drill (extra‑long HSS‑G Twist Drill) is particularly suited to alloyed and unalloyed steel, cast steel, cast iron, sintered iron, malleable iron, non‑ferrous metals and hard plastics, offering robust performance where higher strength and precision are required. Is the MetavCUT Twist Drill suitable for very deep holes? Yes, the MetavCUT extra‑long Twist Drill is designed for deep holes: its extended overall length and the Spiral length make it suitable for deep‑reach applications, and compliance with DIN 1869 underlines its suitability for demanding drilling tasks. For what is a Twist Drill used? It is mainly used for machining high‑strength materials and large bore diameters. This design is easy to resharpen and withstands higher loads. Which three drill types exist? There are metal drills, wood drills and stone/concrete drills. Why are Twist Drills tipped/sharpened? Sharpening reduces the secondary cutting edge at the tip of the Twist Drill, lowering friction forces and thus requiring less feed force while improving centring in the workpiece. Can a metal Twist Drill be used to drill wood? A metal drill can be used in wood but gives poorer guidance and a less clean result; it is easier to regrind and has lower self‑feeding characteristics. For which depths is the Twist Drill the most used tool? A full‑bore hole is made with a Twist Drill. For diameters up to 20 mm and depths up to 100 mm, the Twist Drill is the most commonly used tool.

Twist Drill — Profi Line left-cutting HSS-G 9 mm, 135° (DIN 338) by MetavCUT The Twist Drill left-cutting HSS-G 9 mm is a metal drill bit designed for use in drilling machines and hand drills for efficient extraction and precise metal drilling. Left-cutting geometry for screw extraction and tough tasks 9 mm Diameter for standard metal drilling 135° Tip angle for harder materials like stainless steel HSS-G Material for wear resistance and durability Conforms to DIN 338 for short twist drills with cylindrical shank Superior Performance in Hard Materials thanks to the 135° Tip Angle The Profi Line short twist drill features a 135° tip angle, which reduces entry forces and shortens the pilot time when penetrating harder materials. This geometry is particularly advantageous for stainless steel and other high-strength alloys because it spreads cutting load and decreases the risk of tip wandering. The result is cleaner holes and improved centring in demanding Metal applications. One direct advantage for workshops is fewer rejects and less rework when machining tougher components. Left-cutting Design: Fast Extraction and Lower Feed Force A left-cutting grind means the bit is ground to cut when the spindle turns counterclockwise; this is ideal for removing broken or seized screws and studs. The MetavCUT left-cutting twist drill is optimised for such operations and, according to the manufacturer data, can achieve up to 40% faster drilling while requiring up to 50% less axial feed force compared with conventional HSS drills. For technicians, this translates into reduced operator strain and faster job turnaround when working on repair or disassembly tasks. Material and Standard: HSS-G and DIN 338 for Reliable Use Manufactured from HSS-G, this drill offers a balance of toughness and heat resistance suited for sustained metal cutting. The product is made to DIN 338, the standard describing short twist drills with a cylindrical shank; this ensures consistent shank dimensions, compatible fitting in standard chucks, and predictable performance across production workflows. For buyers this means reliable interchangeability in tool holders and consistent hole quality in serial work. Where this Drill Excels and Who Benefits Most This twist drill is aimed at professionals and maintenance technicians who work with both alloyed and unalloyed steels, cast steels, cast iron, sintered metals, non-ferrous metals and hard plastics. Its left-cutting version is especially useful in repair shops and assembly lines where removal of broken fasteners is frequent. The Profi Line series positions the bit as a practical choice for workshops that require a robust, short drill with dependable centring and reduced push-down effort. For demanding metalwork choose the MetavCUT Profi Line Twist Drill for reliable extraction and efficient drilling — METAV Werkzeuge offers expert advice and comprehensive support, contact via eMail: info@metav-werkzeuge.com, Phone: +49 2822 7131930, WhatsApp: +49 170 2837271 Technical Information Designation: Twist Drill (Spiralbohrer) Brand: MetavCUT SKU: 60090-FDA Diameter: 9 mm Tip Angle: 135° Execution: left-cutting (linksschneidend) For: Drilling Machine / Hand Drill Material: HSS-G Standard: DIN 338 Model Series: Profi Line Packaging unit: 5 Application: Drills for metal Manufacturer: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What is the Twist Drill used for? The MetavCUT Twist Drill is primarily applied to the machining of high-strength materials and larger drill diameters; it is especially suited for alloyed and unalloyed steel, cast steel, cast iron, sintered iron, malleable iron, non-ferrous metals and hard plastics. Its shape allows relatively simple resharpening while maintaining resistance under heavy loads. Which three drill types are there? Commonly distinguished drill types are metal drill bits, wood drill bits and masonry/concrete drill bits. The MetavCUT Twist Drill belongs to the metal drill bit group. Why are twist drills resharpened at the tip? Resharpening the tip of a twist drill reduces the cross-cut edge at the point. By regrinding the point, friction is significantly lowered and less feed force is required; at the same time the bit centres more reliably in the workpiece. Can a Twist Drill be used to drill wood? A metal twist drill such as the MetavCUT Twist Drill can be used in wood, but guidance is inferior and hole quality is usually less clean than with a dedicated wood bit. Metal bits are easier to resharpen and typically exhibit lower self-feeding tendencies. For which drilling depths is the Twist Drill most used? A through hole in solid material is typically produced with a twist drill. For diameters up to 20 mm and drilling depths up to 100 mm, the twist drill is the most commonly used tool. What is better, HSS or HSSE? The common belief that HSSE steels are always superior to standard HSS steels is not universally correct. When choosing between HSS and HSSE, evaluate whether the specific working conditions justify the higher acquisition cost of HSSE.

Twist Drill — MetavCUT Basic Line, 9 mm, 135° Tip, HSS‑G (Short, Bright Finished, DIN 338) The Twist Drill is a short HSS‑G metalworking drill designed for Drilling Machines and handheld use, offering high feed efficiency and stable performance in demanding steel applications. Short design for stable, precise drilling 9 mm diameter for common metalworking tasks 135° tip for improved centring in hard materials Fully ground shank for accurate seating in chucks Conforms to DIN 338 for short twist drills Faster penetration and reduced feed effort for hard metals The HSS‑G composition delivers a clear advantage: up to 40% faster drilling and roughly 50% less thrust compared with conventional HSS bits. For users working with alloyed and unalloyed Steel, Cast Steel, Gusseisen and hard plastics, this means fewer tool changes and smoother cycles. The 135° tip angle reduces the tendency to wander on tough surfaces and shortens dwell during initial engagement. This results in more efficient machining and less operator fatigue. Short geometry for superior stability and hole quality A short overall length and a spiral length of 81 mm minimise overhang and vibration, producing more consistent hole geometry under moderate cutting conditions. The fully ground shank ensures solid clamping in chucks and better concentricity, improving finish and reducing runout. Because the flute length and geometry follow DIN 338, workshop operators benefit from predictable behaviour when switching between comparable short twist drills. Built for metalworking workshops and maintenance tasks This Type N twist drill is the classic choice for metal applications and is optimised for Drilling Machines as well as robust handheld units. Its bright finished surface eases chip evacuation in many metals while remaining straightforward to resharpen when needed. For maintenance engineers, toolroom technicians and small fabrication shops, the combination of 9 mm diameter and short design strikes a balance between versatility and rigidity. Industry standard compliance delivers reproducible results Manufactured to DIN 338 specifications within the MetavCUT Basic Line, this twist drill follows proven dimensional and performance criteria for short cylinder‑shank bits. The Type N normal spiral provides a versatile chip geometry for a wide range of metallic materials. If uncertainty remains about the correct geometry or material choice for a specific application, the short tip geometry and HSS‑G grade allow straightforward regrinding while maintaining performance. We recommend the MetavCUT Twist Drill from the Basic Line for precision metalworking where stability and efficient penetration matter most — for technical questions or selection support contact METAV Werkzeuge for expert advice: info@metav-werkzeuge.com | +49 2822 7131930 | WhatsApp +49 170 2837271 Technical Data Bezeichnung: Twist Drill Marke: MetavCUT SKU: 27090-FDA Durchmesser: 9 mm Spitzenwinkel: 135° Typ: Type N Ausführung: short Farbe: bright finished Material: HSS-G Schaft Ausführung: fully ground Gesamtlänge: 125 mm Spirallänge: 81 mm Anwendung: Drills for metal Norm: DIN 338 Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What materials is the MetavCUT Twist Drill suitable for? The MetavCUT Twist Drill (Type N, HSS‑G) is primarily intended for metalworking; it performs well in alloyed and unalloyed Steel, Cast Steel, Gusseisen and certain hard plastics, offering reliable penetration and chip formation for these materials. How does the short design of the MetavCUT Twist Drill benefit workshop use? A short Twist Drill from MetavCUT reduces overhang and vibration, improving hole accuracy and concentricity; the compact geometry is especially helpful for precise operations and when working with harder materials where deflection must be minimised. For what is a Twist Drill used? A Twist Drill is mainly employed for machining high‑strength materials and larger drill diameters; this form is easy to resharpen and endures higher loads. Which three drill types exist? The main categories are Metal Drills, Wood Drills and Stone/Concrete Drills. Why are Twist Drills sharpened at the tip? Tip sharpening reduces the cross‑cut at the drill tip, lowering friction and thus reducing required feed force while improving centring in the workpiece. Can a Twist Drill be used to drill wood? A Metal Drill can be used in wood, but guidance and finish are inferior compared with dedicated wood drills. Metal drills are easier to resharpen and show less self‑feeding tendency. For which drilling depths is the Twist Drill most commonly used? Twist Drills are the standard choice for through‑hole drilling. For diameters up to 20 mm and depths up to 100 mm they are the most frequently used tool. Is HSS better than HSSE? The common belief that HSSE is always superior to HSS is incorrect; selection should consider the specific working conditions and whether the extra cost of HSSE is justified. Sind Sie sich nicht sicher, ob dieses Werkzeug Ihre Anforderungen erfüllt? Oder benötigen Sie ergänzende technische Daten? Kein Problem – wir stehen Ihnen gerne zur Verfügung. 📧 eMail: info@metav-werkzeuge.com ☎️ Telefon: +49 2822 7131930 ✔️ WhatsApp: +49 170 2837271

Twist Drill — Type N, 9 mm, 135° tip, short, bright finished, HSS-G, DIN 338 (MetavCUT) A short, precision Twist Drill Type N designed for metalworking with a 9 mm diameter and a 135° point angle for stable, clean drilling in hard materials. Short design for higher stability HSS‑G ground for fast, precise drilling 135° point for hard materials like stainless steel Conforms to DIN 338 for short cylindrical drills Fully ground shank for excellent concentricity Durable HSS‑G construction for reliable metalworking The HSS‑G material offers a balance of hardness and edge retention that benefits demanding metalworking tasks. Built as a ground High Speed Steel tool, this short drill delivers sharp cutting edges and high runout accuracy, which reduces burr formation and improves hole quality. For users who prioritize precision, the ground geometry translates into cleaner bores and fewer reworks, while the bright finished surface aids chip evacuation during cutting. Short design increases stability and precision A reduced overall length and a shorter Spiral length improve stiffness during drilling, so less bending occurs under load. This compact geometry is particularly useful when machining legiertem und unlegiertem Stahl and other hard metals, where a rigid tool axis is essential. The shorter overhang results in increased feed stability, enabling higher feed rates in many setups without sacrificing hole accuracy. 135° tip and Type N spiral for hard materials The 135° point angle is tailored to cut into harder materials with reduced tendency to wander at entry, making it suitable for stainless steel and other tougher alloys. As a Type N (normal spiral) configuration, the tool is optimized for metal drilling rather than soft substrates. For less experienced users: a larger tip angle decreases the initial cutting aggressiveness and improves centering, which helps when starting holes in tough components. Precise shank and DIN 338 compliance for machine use With a fully ground shank, the drill provides excellent concentricity and grip in standard drill chucks and toolholders, reducing runout and wear. Conformance to DIN 338 ensures standardized dimensions and compatibility with common tool setup procedures in production and workshop environments. These characteristics make the tool well suited to both stationary machines and portable drilling machines used in metal fabrication. Who benefits and recommended applications Mechanical workshops, toolrooms and production engineers working with steels, cast materials and non‑ferrous metals will find the short Twist Drill especially advantageous for precision holemaking. Its properties support drilling in components where surface finish and positional accuracy matter. For simple explanations: HSS‑G denotes a ground High Speed Steel drill, Type N indicates the classic metal spiral, and the 135° tip suits harder substrates. Strong recommendation: For precision metal drilling choose the MetavCUT short Twist Drill Type N with HSS‑G ground geometry — METAV Werkzeuge offers expert advice and technical support if needed. If unsure whether this tool meets specific requirements or if additional technical data is required, please contact us — 📧 info@metav-werkzeuge.com | ☎️ +49 2822 7131930 | ✔️ WhatsApp +49 170 2837271 Designation: Twist Drill Brand: MetavCUT SKU: 45090-FDA Diameter: 9 mm Point angle: 135° Type: Type N Execution: short Overall length: 125 mm Spiral length: 81 mm Shank execution: fully ground Material: HSS-G Finish: bright finished For drilling machine: Drilling Machine Application: Drills for metal Model series: Standard Line Norm: DIN 338 Colour: bright finished Manufacturer: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What is a Twist Drill used for and which materials suit the MetavCUT Type N drill? The Twist Drill by MetavCUT, Type N, is primarily used for drilling metal; it is ideal for legiertes und unlegiertes Stahl, Gussstahl, Gusseisen and non‑ferrous metals. The Type N spiral and HSS‑G ground geometry ensure reliable cutting in harder materials and give good hole quality in workshop and production settings. Which three drill types exist and where does the MetavCUT Twist Drill fit? Three common drill types are metal drills, wood drills and masonry/concrete drills. The MetavCUT Twist Drill is a metal drill (Type N) and is specifically engineered for use in metalworking rather than for wood or stone. Why is the tip of a Twist Drill sharpened and how does that help in practice? The tip sharpening reduces the cross‑cut edge at the drill point, lowering friction and required feed force. For the MetavCUT Twist Drill Type N this means easier entry, better centering and reduced heat generation, resulting in cleaner holes and longer tool life when combined with appropriate cooling. Can the MetavCUT Twist Drill be used for drilling wood? A metal drill such as the MetavCUT Twist Drill can be used in wood, but it will usually offer less guidance and a rougher finish than a dedicated wood drill. Metal drills are easier to resharpen and exhibit less self‑feeding, so they may require more careful positioning when used in timber.

Spiralbohrer – kurzer HSS‑G Bohrer Ø 9 mm, 135°, Typ N, blank, geschliffen, DIN 338 Der Spiralbohrer ist ein kurzer, geschliffener HSS‑G Metallbohrer, entwickelt für präzise Bohrungen in legiertem und unlegiertem Stahl sowie Gusswerkstoffen. Kurze Ausführung für hohe Stabilität Geschliffene Geometrie für saubere Bohrlöcher 135° Spitzenwinkel für harte Werkstoffe Für Handbohrmaschine und Werkstattgebrauch geeignet DIN 338 konforme Profi Line Ausführung Mehr Produktivität durch kürzere Bauweise und HSS‑G Performance Die kurze Ausführung reduziert die Auskraglänge und sorgt damit für deutlich höhere Stabilität und weniger Neigung zum Verbiegen. Durch den geschliffenen HSS‑G Werkstoff werden Schnittkante und Schneidgeometrie präziser ausgebildet, was nach Herstellerangaben ein bis zu 40 % schnelleres Bohren und 50 % weniger Anpresskraft im Vergleich zu herkömmlichen HSS‑Bohrern ermöglicht. Der direkte Kundennutzen liegt in schnellerer Bearbeitung, geringerer Ermüdung des Anwenders und saubereren Bohrbildern bei wiederholten Serienarbeiten. Zielgerichtet für Stahl, Guss und technische Kunststoffe Dieser Kurzbohrer eignet sich speziell für die Bearbeitung von legiertem und unlegiertem Stahl, Gussstahl, Gusseisen, Sintereisen, Temperguss, Nichteisenmetallen und Hartkunststoffen. Der 135° Spitzenwinkel erleichtert das Anbohren harter Werkstoffe und reduziert das „Wandern“ beim Ansetzen. Für besonders präzise Passungen empfiehlt sich das Anpunkten mit einem Zentrierbohrer vor dem Endbohren; bei Durchmesser 9 mm entspricht das dem empfohlenen Vorgehen für den Standard‑Bereich und gewährleistet reproduzierbare Ergebnisse in der Werkstatt. Geschliffene Qualität verstehen und richtig einsetzen „Geschliffen“ bedeutet, dass die Spannuten und Schneiden per CNC‑Schliff ausgeformt wurden, was sehr scharfe Schneiden und hohe Rundlaufgenauigkeit zur Folge hat. Solche Bohrer liefern saubere Bohrlöcher und exakte Maßtoleranzen, können jedoch empfindlicher gegenüber seitlichen Kräften sein. Deshalb empfiehlt sich bei anspruchsvollen Aufgaben die Nutzung stationärer Maschinen und eine Kühlmittelzufuhr; in vielen Werkstattanwendungen mit robusten Handbohrmaschinen bleibt die Verwendung jedoch problemlos möglich, sofern auf korrekten Spanabfall und Kühlung geachtet wird. Für Profis und anspruchsvolle Heimwerker konzipiert Die Profi Line Ausführung nach DIN 338 verbindet Norm‑Konformität mit einer Fertigungsqualität, die professionelle Anwender erwarten. Dieser Bohrer ist ideal für Werkstätten, Montagebetriebe und Metallhandwerker, die robuste Werkzeuge für präzise Bohrungen benötigen. Die Kombination aus kurzer Bauweise, geschliffener Schaftausführung und Typ N Spirale macht das Werkzeug zu einer verlässlichen Wahl für anspruchsvolle Metallarbeiten. Empfehlung: Für präzise Metallbohrungen die MetavCUT Profi Line Kurzversion mit geschliffenem HSS‑G wählen; bei Fragen berät METAV Werkzeuge persönlich per E‑Mail info@metav-werkzeuge.com oder Telefon +49 2822 7131930 Bezeichnung: Spiralbohrer Marke: MetavCUT SKU: 48090-FDA Durchmesser: 9 mm Spitzenwinkel: 135° Typ: Typ N Material: HSS-G Ausführung: kurz Schaft: geschliffen Gesamtlänge: 125 mm Spirallänge: 81 mm Norm: DIN 338 Farbe: blank Geeignet für: Bohrer für Metall, Handbohrmaschine Modellserie: Profi Line Herstellungsart: geschliffen (HSS-G) Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ Ist der Spiralbohrer von MetavCUT für den Einsatz mit einer Handbohrmaschine geeignet? Der Spiralbohrer von MetavCUT (Typ N, HSS‑G, kurz) ist für Werkstatt‑ und Handgebrauch ausgelegt und kann mit einer Handbohrmaschine eingesetzt werden; bei höchsten Präzisionsanforderungen empfiehlt sich jedoch das Anpunkten und die Nutzung stationärer Maschinen zur Minimierung seitlicher Belastungen. Warum ist die geschliffene Ausführung beim Spiralbohrer wichtig? Die geschliffene Ausführung des MetavCUT Spiralbohrers (HSS‑G) sorgt für sehr scharfe Schneiden und hohe Rundlaufgenauigkeit, was saubere Bohrlöcher und präzise Maßhaltigkeit ermöglicht; gleichzeitig erfordert die geschliffene Geometrie sorgfältige Handhabung und gegebenenfalls Kühlung. Für welche Materialien ist der MetavCUT Spiralbohrer am besten geeignet? Der MetavCUT Spiralbohrer eignet sich besonders für legierte und unlegierte Stähle, Gusswerkstoffe sowie Nichteisenmetalle und Hartkunststoffe; der 135° Spitzenwinkel unterstützt das Anbohren harter Materialien und reduziert das Wandern beim Ansetzen. Welche Vorteile bietet die DIN 338 Norm bei diesem Bohrer? Die DIN 338 Klassifikation garantiert, dass der MetavCUT Spiralbohrer den Normanforderungen für kurze Spiralbohrer mit Zylinderschaft entspricht, was Kompatibilität mit gängigen Spannfuttern und reproduzierbare Fertigungsqualität sicherstellt. {"@context":"https://schema.org","@graph":[{"@type":"Product","@id":"#48090-FDA","sku":"48090-FDA","mpn":"48090-FDA","name":"Spiralbohrer 48090-FDA","description":"Kurzer geschliffener HSS‑G Spiralbohrer Ø 9 mm, 135° Spitzenwinkel, Typ N, blank, DIN 338; geeignet für legierte und unlegierte Stähle, Gusswerkstoffe und Hartkunststoffe; hohe Stabilität durch kurze Ausführung, geschliffene Geometrie für saubere Bohrlöcher.","image":["https://files.plytix.com/api/v1.1/file/public_files/pim/assets/57/c3/98/62/6298c3575d155f1bc7e497fd/images/8e/48/c5/69/69c5488eb2b3400ba580741b/logo-metav-1200-1200.png","https://files.plytix.com/api/v1.1/file/public_files/pim/assets/57/c3/98/62/6298c3575d155f1bc7e497fd/images/8e/48/c5/69/69c5488eb2b3400ba580741e/logo-metav-1200-900.png","https://files.plytix.com/api/v1.1/file/public_files/pim/assets/57/c3/98/62/6298c3575d155f1bc7e497fd/images/8e/48/c5/69/69c5488eb2b3400ba580741c/logo-metav-1200-675.png"],"additionalProperty":[{"@type":"PropertyValue","name":"Bezeichnung","value":"Spiralbohrer"},{"@type":"PropertyValue","name":"Marke","value":"MetavCUT"},{"@type":"PropertyValue","name":"Durchmesser","value":"9 mm"},{"@type":"PropertyValue","name":"Spitzenwinkel","value":"135°"},{"@type":"PropertyValue","name":"Typ","value":"Typ N"},{"@type":"PropertyValue","name":"Farbe","value":"blank"},{"@type":"PropertyValue","name":"Ausführung","value":"kurz"},{"@type":"PropertyValue","name":"Norm","value":"DIN 338"},{"@type":"PropertyValue","name":"Material","value":"HSS-G"},{"@type":"PropertyValue","name":"Schaftausführung","value":"geschliffen"},{"@type":"PropertyValue","name":"Gesamtlänge","value":"125 mm"},{"@type":"PropertyValue","name":"Spirallänge","value":"81 mm"},{"@type":"PropertyValue","name":"Anwendung","value":"Bohrer für Metall"},{"@type":"PropertyValue","name":"Modellserie","value":"Profi Line"},{"@type":"PropertyValue","name":"Hersteller","value":"Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com"}]},{"@type":"FAQPage","mainEntity":[{"@type":"Question","name":"Ist der Spiralbohrer von MetavCUT für den Einsatz mit einer Handbohrmaschine geeignet?","acceptedAnswer":{"@type":"Answer","text":"Der Spiralbohrer MetavCUT Spiralbohrer (Typ N, HSS‑G, kurz) eignet sich für Werkstatt‑ und Handgebrauch und kann mit einer Handbohrmaschine verwendet werden; bei höchsten Präzisionsanforderungen empfiehlt sich jedoch Anpunkten mit einem Zentrierbohrer und die Nutzung stationärer Maschinen zur Minimierung seitlicher Belastungen."}},{"@type":"Question","name":"Warum ist die geschliffene Ausführung beim Spiralbohrer wichtig?","acceptedAnswer":{"@type":"Answer","text":"Die geschliffene Ausführung des MetavCUT Spiralbohrers (HSS‑G) sorgt für sehr scharfe Schneiden und hohe Rundlaufgenauigkeit, was saubere Bohrlöcher und präzise Maßhaltigkeit ermöglicht; zugleich erfordert die geschliffene Geometrie sorgfältige Handhabung und gegebenenfalls Kühlung."}},{"@type":"Question","name":"Für welche Materialien ist der MetavCUT Spiralbohrer am besten geeignet?","acceptedAnswer":{"@type":"Answer","text":"Der MetavCUT Spiralbohrer ist besonders geeignet für legierten und unlegierten Stahl, Gussstahl, Gusseisen, Sintereisen, Temperguss, Nichteisenmetalle und Hartkunststoffe; der 135° Spitzenwinkel unterstützt das Anbohren harter Materialien und reduziert das Wandern beim Ansetzen."}},{"@type":"Question","name":"Welche Vorteile bietet die DIN 338 Norm bei diesem Bohrer?","acceptedAnswer":{"@type":"Answer","text":"Die DIN 338 Klassifikation garantiert, dass der MetavCUT Spiralbohrer den Normanforderungen für kurze Spiralbohrer mit Zylinderschaft entspricht, was Kompatibilität mit gängigen Spannfuttern und reproduzierbare Fertigungsqualität sicherstellt."}}]},{"@type":"ItemPage","url":"https://metav-shop.de/produkt/48090-FDA","dateModified":"2026-05-04T12:00:00+01:00","author":{"@type":"Person","name":"Stephan Bayer","url":"https://www.linkedin.com/in/stephan-bayer/"},"publisher":{"@type":"Organization","name":"Metav Werkzeuge GmbH","url":"https://metav-shop.de","logo":{"@type":"ImageObject","url":"https://files.plytix.com/api/v1.1/file/public_files/pim/assets/57/c3/98/62/6298c3575d155f1bc7e497fd/images/8e/48/c5/69/69c5488eb2b3400ba580741c/logo-metav-1200-675.png","width":1200,"height":675},"address":{"@type":"PostalAddress","streetAddress":"Parkring 45","postalCode":"46446","addressLocality":"Emmerich","addressCountry":"DE"},"telephone":"+49 2822 7131930","email":"info@metav-werkzeuge.com"},"about":[{"@type":"Thing","name":"Kurzbohrer für Metall"},{"@type":"Thing","name":"HSS‑G geschliffen"},{"@type":"Thing","name":"DIN 338 kurze Spiralbohrer"}],"mentions":[{"@type":"Thing","name":"Profi Line"},{"@type":"Thing","name":"Typ N Spiralgeometrie"},{"@type":"Thing","name":"Polierblanke Oberfläche"}]}]}

Twist Drill — Short HSS-G Drill, 9 mm, 118° point, TIN-coated, DIN 338, fully ground, MetavCUT A short Twist Drill designed for precise metal drilling with Drilling Machines Short design for increased stability and precision TIN-coated surface for reduced wear and friction HSS-G fully ground for faster drilling and clean holes 118° point angle for easy centring in softer metals Conforms to DIN 338 for consistent manufacturing quality Durable HSS-G Construction for Longer Tool Life The HSS-G base material combined with a TIN-coated surface delivers extended lifetime when working with metallic materials. This composition reduces surface wear and friction, so heat buildup is minimised during continuous drilling. The coating supports improved tool life particularly under intermittent cooling, while the substrate material retains cutting edge stability for demanding machining tasks. Short Design and Fully Ground Geometry for Precise Results A shorter overall length reduces overhang and increases stability, which directly improves concentricity and reduces vibration during drilling. The fully ground flute geometry creates sharper cutting edges, enabling up to faster penetration with lower feed forces compared to rolled types. The 118° point angle favours centring and controlled entry in softer metals and certain non-ferrous alloys while still offering reliable starts on slightly curved surfaces. Optimised for Metalworking and Professional Use Designed for use with Drilling Machines, this tool excels in machining alloyed and unalloyed steel, Tempered Cast Iron, Gusseisen, Sintered Iron, Copper, Bronze and hard plastics. Workshops and maintenance professionals benefit from consistent hole quality and reduced rework. The tool’s characteristics make it particularly suitable for precision tasks where minimized runout and reproducible hole tolerances matter. DIN 338 Standard and Practical Handling Advice Manufactured to DIN 338, the tool follows industry definitions for short Twist Drills with Cylindrical Shanks. Being ground rather than rolled results in sharper edges and higher runout accuracy, but also a slightly increased susceptibility to fracture under improper handling. Use appropriate coolant for extended tool life and prefer stationary or well-supported setups to exploit the drill’s precision advantages. Strongly recommend MetavCUT’s short TIN-coated HSS-G Twist Drill for demanding metalworking tasks — for expert advice and application support contact METAV Werkzeuge: 📧 info@metav-werkzeuge.com | ☎️ +49 2822 7131930 | ✔️ WhatsApp +49 170 2837271 — METAV Werkzeuge offers extensive and competent consultation for technical queries and product selection Bezeichnung: Twist Drill Marke: MetavCUT SKU: 28090-FDA Durchmesser: 9 mm Spitzenwinkel: 118° Gesamtlänge: 125 mm Spirallänge: 81 mm Ausführung: short Schaft Ausführung: fully ground Farbe / Beschichtung: TIN-coated Material: HSS-G Norm: DIN 338 Für Bohrmaschine: Drilling Machine Anwendung: Drills for metal Modellserie: Basic Line Hersteller: MetavCUT Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What is the MetavCUT Twist Drill used for? The MetavCUT Twist Drill is mainly applied to the machining of high-strength materials and larger drill diameters; its short design and robust geometry make it suitable for demanding metalworking tasks. The tool’s shape allows relatively easy resharpening and it withstands considerable loads while delivering clean, precise holes. Which three drill types exist? The common classification names three main categories: Metal drills, Wood drills and Masonry/Concrete drills. The MetavCUT Twist Drill belongs to the metal drill group and is optimised for the properties and requirements of metallic materials.

Twist Drill — Short HSS-G Type N, 9 mm, 135°, TiN-coated, DIN 338 The Twist Drill is a short HSS-G metalworking drill bit (Type N) designed for precision drilling in hard materials and optimised for use in drilling machines. Short design for higher stability TiN-coated for extended tool life Fully ground shank for cleaner holes 135° tip for hard metals and stainless steel Conforms to DIN 338 for short drill bits Durable Material and Coating for Long Service Life The short HSS-G construction combined with the TiN-coated surface reduces friction and wear during metalworking, which translates into a significantly longer lifetime under continuous use. With a 9 mm diameter and a flute length of 81 mm, this bit is especially suited for alloyed and unalloyed steel, cast iron, sintered iron, nickel silver, copper, bronze and hard plastics. The TiN layer lowers surface temperature and, when used with appropriate cooling, decreases abrasive wear and maintains cutting performance over prolonged operations. Stable Short Design for Precise, Efficient Drilling Thanks to the reduced overhang of the short execution, this Twist Drill provides superior stability and resists bending under load, enabling more accurate hole positions and improved concentricity. The fully ground geometry yields sharp cutting edges and high running accuracy, allowing up to 40% faster penetration and requiring about 50% less feed force compared with conventional HSS drills. These advantages make it a reliable choice for demanding production and workshop environments where precision and throughput matter. Optimised Tip Geometry and Suitable Applications The 135° point angle is tailored for harder materials and stainless steel: it shortens the initial penetration time and improves centring on tough surfaces. As a Type N normal-spiral bit, the tool excels at general metal drilling tasks and is intended primarily for use with drilling machines. Typical fields of application include maintenance, toolrooms and manufacturing where metals such as steel, cast components and non-ferrous alloys must be drilled with repeatable quality. Compliance, Manufacturing and Best Practice Manufactured according to DIN 338 as a short, cylindrical-shank Spiral Drill, this product is produced as a ground (HSS-G) variant, which implies CNC-ground flutes for sharp edges and precise geometry. Ground drills generally offer cleaner holes and better accuracy than roll-formed types, though they can be somewhat more brittle and therefore are recommended for use with suitable coolant and in predominantly stationary mounting conditions. For optimal results, pair the bit with controlled speeds, adequate coolant and a solid clamping system. For precision metalworking, choose the MetavCUT Twist Drill Type N with TiN coating — for technical advice or to confirm suitability, METAV Werkzeuge provides expert consultation via email info@metav-werkzeuge.com, by phone +49 2822 7131930 or WhatsApp +49 170 2837271 Designation: Twist Drill Brand: MetavCUT SKU: 46090-FDA Diameter: 9 mm Flute Length (Spirallänge): 81 mm Total Length (Gesamtlänge): 125 mm Point Angle (Spitzenwinkel): 135° Type: Type N Execution (Ausführung): short Shank Finish (Schaft-Ausführung): fully ground Coating (Farbe): TiN-coated Material: HSS-G Standard (Norm): DIN 338 Application: Drills for metal / Bohrer für Metall Intended Machine (Für Bohrmaschine): Drilling Machine / Handbohrmaschine Model Series (Modellserie): Standard Line Manufacturer: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What is the Twist Drill (MetavCUT, Type N) mainly used for? The MetavCUT Twist Drill Type N is primarily applied to machining high-strength materials and larger hole diameters; it performs well on alloyed and unalloyed steels and similar metals. Its form allows easier regrinding and it endures considerable loads, making it suitable for demanding metalworking tasks. Which three drill types exist? The main categories are Metal drills (such as the MetavCUT Twist Drill), Wood drills and Masonry/Concrete drills. Each type is optimised in geometry and material for its intended substrate.

Twist Drill Profi Line — 9 mm, 135° · Type N · TIN-coated · Short · HSS‑G · DIN 338 The Twist Drill Profi Line is a short Type N drill designed for precision metalworking with Drilling Machines and Hand Drills. Short design for higher stability and precision TIN-coated HSS‑G for extended tool life Fully ground shank for fast, low-force drilling Optimised 135° tip for hard metals Conforms to DIN 338 for reliable quality Precision and productivity for metalworking Kurz-design drills like the Twist Drill Profi Line combine a reduced overhang with a robust geometry, resulting in higher Stability and less tendency to deflect when drilling. The HSS‑G material paired with a TIN‑coating reduces friction and wear, so holes in alloyed and unalloyed steel, cast components and non‑ferrous metals are produced with consistent accuracy. This yields a measurable time advantage in series work and minimises rework. Less effort, faster penetration with fully ground geometry A fully ground flute and refined cutting geometry ensure the drill requires up to 50% less feed force and can cut faster, especially in demanding materials. The 135° point angle shortens the initial entry time on hard materials such as stainless steel, while the precise tip improves centring. For users, this means easier handling on handheld machines and more predictable results on stationary Drilling Machines. Robust short format tailored to demanding tasks The short overall length (125 mm) and spiral length (81 mm) make this drill particularly suited to operations where rigidity is decisive. The Type N normal helix is the classic choice for metalworking, offering reliable chip evacuation across a broad range of alloys. Operators benefit from cleaner holes and less vibration, which is especially valuable when drilling tougher materials or when hole quality is critical. Practical explanation of key terms The designation HSS‑G indicates a High Speed Steel drill produced by grinding (G = ground), which provides very sharp cutting edges and excellent concentricity. TIN‑coated refers to a thin layer of Titanium Nitride that increases surface hardness and reduces adhesive wear. DIN 338 classifies short twist drills with cylindrical shanks and ensures interchangeability and consistent dimensions across manufacturers. Strong recommendation: For demanding metal drilling choose the MetavCUT Profi Line Twist Drill — for advice or to confirm suitability contact METAV Werkzeuge: 📧 info@metav-werkzeuge.com ☎️ +49 2822 7131930 ✔️ WhatsApp +49 170 2837271 Designation: Twist Drill / Spiralbohrer Marke: MetavCUT SKU: 41090-FDA Diameter: 9 mm Point Angle: 135° Type: Type N Execution: Short Colour/Coating: TIN-coated Material: HSS‑G Shank Execution: Fully ground Spiral Length: 81 mm Overall Length: 125 mm For Drilling Machine: Drilling Machine / Hand Drill suitability indicated Norm: DIN 338 Series: Profi Line Application: Drills for metal Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What is the MetavCUT Profi Line Twist Drill used for? The MetavCUT Profi Line Twist Drill is primarily used for machining high‑strength materials and larger diameters; it is especially effective when drilling alloyed or unalloyed steel and other metals where a short, rigid tool is required. Its construction allows it to withstand higher loads and deliver precise hole geometry. Which three drill types exist? Generally, three common drill categories are distinguished: Metal Drills, Wood Drills and Masonry/Concrete Drills. The MetavCUT Profi Line Twist Drill belongs to the Metal Drill category and is optimised for metalworking tasks. Why are twist drills re‑pointed? Re‑pointing reduces the cross‑cut at the tip of the Twist Drill, significantly lowering friction and therefore the required feed force; at the same time the tip centres better in the workpiece, improving hole accuracy. Can a metal drill be used for wood? A Metal Drill such as the MetavCUT Profi Line can be used in wood, but guidance and hole finish are inferior compared with dedicated wood drills. Metal drills are easier to re‑sharpen and have less self‑pulling action, which can be an advantage in some manual operations. For which drilling depths is the Twist Drill most commonly used? A through‑hole in solid material is typically executed with a Twist Drill. For diameters up to 20 mm and drilling depths up to 100 mm, the Twist Drill is the most frequently used tool, offering efficient chip removal and reliable performance. Is HSS or HSSE better? The common assumption that HSSE alloys are categorically superior to HSS is not always correct. Selection should be based on working conditions: HSSE can offer advantages in specific high‑speed or abrasive situations, but the higher purchase cost must be justified by the application. Are you unsure whether this tool meets your requirements or need additional technical data? METAV Werkzeuge offers comprehensive, expert consultation — contact us by email at info@metav-werkzeuge.com, by phone at +49 2822 7131930 or via WhatsApp at +49 170 2837271.

Twist Drill — Metal Drill HSS‑G, Ø 9 mm, 135° Point, Spezial, DIN 338, with multi‑bevel cutting edge and triangular shank, MetavCUT The Twist Drill HSS‑G metal drill is designed for fast, precise holes in steel and other hard materials, suitable for hand and stationary drilling machines. Fast drilling: up to 40% quicker than standard HSS Requires 50% less feed force 135° point for harder materials 3‑flat shank for secure grip in cordless drills Conforms to DIN 338 for short twist drills Faster metalworking with less effort This HSS‑G tool delivers a measurable productivity gain thanks to a specially ground geometry that enables up to 40% faster drilling while needing 50% less feed force than conventional HSS drills. The result is reduced operator fatigue and higher throughput in repetitive tasks. For workshops and industrial users who value cycle time, the shortened drilling time translates directly into improved efficiency and lower labour costs per hole without compromising hole quality. Cleaner entry and reliable centring in hard materials The 135° point is optimised for harder workpiece materials such as stainless steel and tempered alloys; it reduces wandering at the start of the hole and shortens the required plunge distance. By decreasing the chisel edge width, the point geometry lowers friction and cutting forces, which helps produce burr‑reduced, clean hole edges. For users unfamiliar with tip angles: a larger point angle typically penetrates harder materials more easily and provides better centring. Secure clamping and compatibility for hand tools The design with a triangular shank (3‑flat shank) ensures slip‑free engagement in chucks of cordless and hand drills, improving torque transfer and reducing slippage during exertion. Conformance to DIN 338 classifies this as a short twist drill with a cylindrical shank made of high‑speed steel, so it fits standard toolholders and is suitable for both mobile and stationary applications. METAV Werkzeuge offers expert consultation if there are questions about drill retention or machine compatibility. Tailored for demanding applications and varied materials Manufactured from HSS‑G, this Rapid‑type drill is suitable for a broad spectrum of materials including alloyed and unalloyed steels, cast and temper‑cast steels, non‑ferrous metals, hard plastics and also for occasional use in wood. Its geometry focuses on reliable performance in metalworking environments; the short configuration is particularly advantageous where rigidity and minimal runout are required. For precision shops, maintenance teams or professionals, this tool combines robustness with straightforward resharpening. Strong recommendation: For professionals seeking faster, cleaner holes in tough materials, choose the MetavCUT HSS‑G Twist Drill — METAV Werkzeuge provides comprehensive technical advice and support via email, phone and WhatsApp: info@metav-werkzeuge.com | +49 2822 7131930 | WhatsApp +49 170 2837271 Designation: Twist Drill Brand: MetavCUT SKU: 55090-FDA Diameter: 9 mm Point angle: 135° Spiral length: 81 mm Total length: 125 mm Shaft execution: with multi‑bevel cutting edge and triangular shank Model series: Spezial Material: HSS‑G Standard: DIN 338 Application: Drill for metal Suitable for: Drilling Machine (hand drill) Packaging unit: 5 Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ For what is a Twist Drill used? The MetavCUT Twist Drill is primarily applied to the machining of high‑strength materials and larger bore diameters; its shape is easy to regrind and it withstands greater loads, making it ideal for demanding metalworking operations. Which three drill types exist? Common drill types are metal drills, wood drills and stone/concrete drills, and the MetavCUT Twist Drill belongs to the metal drill category tailored for metal machining. Why are Twist Drills pointed? Pointing reduces the chisel edge at the tip of the Twist Drill, which significantly lowers friction and therefore requires less feed force; at the same time the point improves centring of the drill in the workpiece. Can a Twist Drill be used to drill wood? A metal drill such as the MetavCUT Twist Drill can be used in wood, but guidance is inferior and the finish is less clean; however these drills are easier to resharpen and show less self‑feed. At which drilling depths is the Twist Drill most used? A full‑bore hole is often executed with a Twist Drill. For diameters up to 20 mm and drilling depths up to 100 mm the Twist Drill is the most commonly used tool. What is better, HSS or HSSE? The general belief that HSSE steels are inherently superior to normal HSS is incorrect; when choosing between HSS and HSSE for a MetavCUT Twist Drill, assess working conditions carefully to determine whether the higher purchase cost of HSSE is justified.

MetavCUT Twist Drill — Twist Drill, 9 mm, 135° tip, Long, Bright finished, HSS‑G, DIN 340 The MetavCUT Twist Drill is a long HSS‑G Twist Drill engineered for deep, precise metal drilling in demanding applications with a 9 mm diameter and a 135° tip. Long HSS‑G Twist Drill for deep holes 9 mm diameter for precise metal drilling 135° tip for hard materials like stainless steel Fully ground shank for high runout accuracy Conforms to DIN 340 for deep hole performance High cutting performance for tough metals Designed to handle challenging materials, this long HSS‑G Twist Drill excels in drilling legierte und unlegierte Stahl grades and cast irons. The larger 135° tip angle reduces entry forces for harder workpieces and improves centring, while the long flute length allows access to recessed holes. Users benefit from faster advance and reduced effort, since the ground geometry promotes a sharper cutting edge and cleaner chip removal. Precise geometry for accurate bores A fully ground shaft and CNC‑ground flutes ensure high runout accuracy and consistently round holes, which is critical when machining components that require tight tolerances. The ground manufacturing method yields very sharp edges and precise tolerance control; however, the harder geometry is best used with appropriate feed, cooling and, for portable setups, cautious handling to avoid brittle breakage. Practical advantages in workshop and production Because the long variant follows DIN 340, it is suited for deeper bores, bushings and situations with limited accessibility. The bright finished surface aids visual inspection and reduces initial friction during entry. For metalworking tasks in small series or repair work the tool reduces rework thanks to cleaner holes, making it an efficient choice where reliability and repeatability matter most. Who benefits and how to use it safely Engineers, toolroom technicians and maintenance professionals profit from the combination of HSS‑G hardness and long design when working on automotive, mechanical and maintenance applications. When using this Twist Drill in stationary machines, apply cutting fluid and moderate speed for best life expectancy. For handheld Drilling Machines, maintain firm guidance and lower advance rates to minimise breakage risk. We recommend the MetavCUT long HSS‑G Twist Drill for demanding deep metal bores — for personalised advice, drill parameter recommendations or further technical data contact METAV Werkzeuge: info@metav-werkzeuge.com, phone +49 2822 7131930 or WhatsApp +49 170 2837271 Designation: Twist Drill Brand: MetavCUT SKU: 53090-FDA Diameter: 9 mm Total length: 175 mm Spiral length: 115 mm Tip angle: 135° Material: HSS‑G Execution: Long Colour: Bright finished Shank execution: Fully ground Standard: DIN 340 For drilling machine: Drilling Machine Application: Drills for metal Model series: Standard Line Packaging unit: 5 Manufacturer: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What is the MetavCUT Twist Drill best used for? The MetavCUT Twist Drill is primarily intended for metalworking and is applied for drilling in high‑strength and cast materials where long, stable bores are required; it is especially suitable for deep holes and hard materials. Can the MetavCUT Twist Drill be re‑sharpened and reused? Yes, the MetavCUT Twist Drill made of HSS‑G can be re‑sharpened by grinding; attention should be paid to preserving the original tip angle and flute geometry to maintain performance. For what are Twist Drills used? The MetavCUT Twist Drill is mainly used when machining high‑strength materials and larger diameters; its form is relatively easy to re‑grind and it stands up to higher loads. Which 3 drill types exist? The main categories are metal drills, wood drills and stone/concrete drills; the MetavCUT Twist Drill belongs to the metal drill type. Why are Twist Drills pointed? The point grind reduces the cross‑cut at the tip of the MetavCUT Twist Drill, lowering friction and required feed forces while improving centring accuracy in the workpiece. Can you drill wood with a Twist Drill? A metal drill such as the MetavCUT Twist Drill can be used in wood, but guidance and finish are inferior compared with dedicated wood drills; metal drills are easier to re‑sharpen and have less self‑feed. At which drilling depths is the Twist Drill most used? Solid drilling for diameters up to around 20 mm and depths up to 100 mm is the most frequent use case; the MetavCUT Twist Drill is a common choice for such through‑holes and deep bores. What is better, HSS or HSSE? Choosing between HSS and HSSE depends on working conditions; the common assumption that HSSE is universally superior is incorrect — evaluate whether the application justifies the higher cost relative to the actual material and speed demands.