High-precision drills for reliable, high-throughput metalworking
Drills provide the fundamental rotating cutting solution for producing accurate cylindrical holes in materials such as structural steel, high-alloy stainless steel, cast iron, non-ferrous metals and engineering plastics, delivering consistent hole quality and extended tool life in CNC machining and turning centres. This category covers everything from classic twist drill made from high-speed steel for general machining to solid carbide drill optimised for high cutting speeds and long run times, offering advanced coatings and internal coolant options for improved heat management. By using optimised point geometries and split points the tools reduce thrust, prevent walking at the start of the cut and ensure superior surface finish, which benefits sectors from general mechanical engineering to automotive component manufacture.
8mm Centre Drill DIN 333 Form A 60° Tip HSS, For Centre Holes In Steel Up To 800 N Feed 0.06mm/Revolution - TECWERK
Take advantage of robust centring accuracy and predictable feed behaviour thanks to the combination of HSS construction and the DIN 333 Form A geometry; order directly via Metav Werkzeuge for reliable supply or consult the team for specification advice. TECWERK centre drill DIN 333 Form A, 8 mm – HSS, 60° countersink, right-hand A TECWERK centre drill designed for producing accurate centring holes to DIN 332, suitable for general workshop and toolroom use HSS material for reliable cutting performance DIN 333 Form A geometry for accurate centring 60° countersink angle for standard centring holes Feed in steel up to 800 N: 0.06 mm/rev Reduced runout through standardised geometry The DIN 333 Form A design provides a defined pilot and countersink geometry that reduces runout and improves subsequent drilling accuracy. Constructed from HSS, the tool combines toughness and edge retention, which leads to consistent centring even in repetitive machining cycles. Using a standardised centre geometry ensures compatibility with established holemaking sequences and reduces rework in component manufacturing. Predictable cutting behaviour and chip control A 60° countersink angle yields the commonly required centring profile for drilling preparation; paired with a specified feed in steel up to 800 N: 0.06 mm/rev, the result is reproducible chip formation and lower radial load on the workpiece. The right-hand design matches conventional spindle rotation, enabling straightforward integration into existing setups. These measurable parameters support process planning and minimise trial-and-error during production runs. Practical benefits for daily workshop use The tool’s HSS composition and Form A shape make it suitable for general-purpose centring across a range of ferrous materials. The defined geometry shortens cycle times by producing reliable centres that guide follow-up drills, improving first-pass yield. Maintenance is simplified by the ability to regrind HSS cutters when the edge softens, extending service life and reducing consumable costs in the long term. Integration into production workflows Designed for straightforward clamping in standard chucks and toolholders, the centre drill supports quick changeovers and predictable set-up times. The standard-compliant design facilitates documentation and tool lists for quality systems, while consistent performance contributes to stable process capability. Ideal for workshops, maintenance departments and small-batch production where reproducibility and simplicity are priorities. Choose the TECWERK centre drill for dependable centring performance and contact Metav Werkzeuge for procurement or technical clarification to ensure optimal selection for intended applications Technical data Article number: 2111651800NW Label: Zentrierbohrer DIN 333 Form A D.8mm HSS re.TECWERK Manufacturer: TECWERK Facts Diameter: 8 mm Countersink angle: 60° Feed in steel up to 800 N: 0.06 mm/rev Standard: DIN 333 / for centring to DIN 332 Special features HSS material DIN 333 Form A geometry Right-hand orientation For general-purpose centring holes No pilot countersink required (to produce centring holes to DIN 332) FAQ What materials can this centre drill be used with? The centre drill is made of HSS and is intended for general-purpose centring operations, commonly used in steels and similar ferrous materials; the specification notes a feed guidance for steel up to 800 N at 0.06 mm/rev. How does the DIN 333 Form A design improve drilling accuracy? The DIN 333 Form A geometry establishes a precise pilot and a 60° countersink profile, which reduces runout when producing centring holes and improves guidance for subsequent drilling processes. Is this a right-hand or left-hand tool? This item is a right-hand centre drill, designed for conventional spindle rotation and standard clamping systems in workshop environments. Can the tool be re-sharpened? The HSS construction permits regrinding of the cutting edges when appropriate, extending tool life and supporting cost-efficient workshop practice. Which standards does the tool comply with for centring operations? The centre drill is specified to DIN 333 and is intended for producing centring holes in accordance with DIN 332 profiles. Manufacturer / Responsible: NORDWEST Handel AG, Robert-Schuman-Straße 17, 44263 Dortmund
8mm HSS Twist Drill DIN 338 ,short, roll forged, black, Type N - MetavCUT
Der Spiralbohrer in HSS überzeugt durch die Kombination aus hoher Stabilität durch die kurze Ausführung und der Normkonformität nach DIN 338, was präzise Metallbohrungen erlaubt. Nutzen Sie die robuste Geometrie mit einem Spitzenwinkel von 118° und der für Handbohrmaschine geeigneten Zylinderschaft. Bestellungen und fachliche Beratung erhalten Sie direkt über Metav Werkzeuge oder per Technische Beratung anfordern. Spiralbohrer 8 mm (HSS, kurz) von MetavCUT Der Spiralbohrer 8 mm ist ein kurzer HSS-Bohrer nach DIN 338 für präzises Bohren in Metall an Handbohrmaschine und stationären Maschinen. HSS-Schnellarbeitsstahl für Stahl und Metall Normgerechte Ausführung nach DIN 338 Kurze Bauform für hohe Stabilität Spitzenwinkel 118° für universelle Anwendung Zylinderschaft für Handbohrmaschine Hohe Stabilität für präzise Metallbearbeitung Die kurze Ausführung des Bohrers reduziert die Auskraglänge und sorgt so für erhöhte Stabilität bei Kraftübertragung und Führung. Durch die Verwendung von HSS bleibt die Schneide zäh und widerstandsfähig gegen thermische Belastung, was besonders bei Serien von mittelgroßen Bohrungen im Werkstattalltag von Vorteil ist. Diese Konstruktion vermindert Schwingungen und reduziert damit das Risiko von Werkzeugbruch sowie das Entstehen von Unrundheiten. Passende Anwendungen und Maschinenkompatibilität Der Durchmesser von 8 mm fällt in den Bereich für allgemeine Werkstatt- und Montagearbeiten und eignet sich deshalb besonders für dünne bis mittlere Bleche, Profile sowie Baustahl, Aluminium und Kunststoffe. Einsatz an Handbohrmaschine und stationären Säulenbohrmaschinen ist möglich, wobei bei hochpräzisen Passungen ein Anpunkten mit Zentrierbohrer empfohlen wird. Der Typ N Normalspirale ist speziell auf Metall zugeschnitten und bietet zuverlässige Spanabfuhr bei üblichen Vorschubwerten. Bohrgeometrie, Spitzenwinkel und Bedienhinweise Der Spitzenwinkel 118° ermöglicht ein ausgewogenes Eindringverhalten und gute Zentrierfähigkeit auf flachen und leicht gewölbten Oberflächen; für sehr harte Werkstoffe wäre ein größerer Winkel vorteilhaft. Die Spirallänge 75 mm und die Gesamtlänge 117 mm bieten ausreichend Spanraum für saubere Spanabfuhr. Zur Verlängerung der Standzeit empfiehlt sich passende Kühlschmierstoffzufuhr und abgestimmte Schnittdaten sowie bei Bedarf das Vorbohren zur Entlastung der Querschneide. Qualität, Norm und Eignung für den Werkstattalltag Die Fertigung nach DIN 338 garantiert die standardisierte Abmessung und Ausführung kurzer Spiralbohrer mit Zylinderschaft, was die Austauschbarkeit und Lagerhaltung erleichtert. Die Ausführung in HSS und die Typisierung als Typ N sichern die Vielseitigkeit im Einsatzfeld Metall. MetavCUT steht für zuverlässige Werkzeuge, und Metav Werkzeuge bietet transparente Versorgung sowie technische Beratung aus Emmerich für Anwender in Industrie und Handwerk. Empfehlung: Für belastbare und präzise Metallbohrungen das MetavCUT HSS-Kurzspiralbohrer-Programm wählen; Bestellungen und technische Rückfragen gern über Metav Werkzeuge per eMail info@metav-werkzeuge.com oder Telefon +49 2822 7131930 Produktmerkmale Artikelnummer: 40080-FDA Marke: MetavCUT Bezeichnung: Spiralbohrer Fakten Durchmesser: 8 mm Gesamtlänge: 117 mm Spirallänge: 75 mm Spitzenwinkel: 118° Verpackungseinheit: 5 Besonderheiten Material: HSS Norm: DIN 338 (kurze Spiralbohrer mit Zylinderschaft) Ausführung: kurz Typ: Typ N Farbe: schwarz Für Bohrmaschine: Handbohrmaschine Anwendung: Bohrer für Metall FAQ Für welche Materialien eignet sich der Bohrer am besten? Der MetavCUT Spiralbohrer (Spiralbohrer, Typ N, SKU 40080-FDA) eignet sich besonders für legierten und unlegierten Stahl, Gusseisen, Nichteisenmetalle und Kunststoffe und ist damit eine vielseitige Wahl für Werkstatt und Montage. Ist der Bohrer für den Einsatz in einer Handbohrmaschine geeignet? Ja, der Spiralbohrer von MetavCUT ist wegen der kurzen Ausführung und dem Zylinderschaft für die Nutzung an Handbohrmaschine freigegeben und bietet dort gute Stabilität. Welchen Spitzenwinkel hat der Bohrer und was bedeutet das für die Anwendung? Der Spitzenwinkel beträgt 118°, was universelle Einsatzmöglichkeiten fördert und besonders bei Aluminium und allgemeinen Metallarbeiten für gutes Eindringverhalten sorgt. Wie lang sind Spirale und Bohrer insgesamt? Die Spirallänge beträgt 75 mm, die Gesamtlänge 117 mm; diese Dimensionen gewährleisten ausreichende Spanabfuhr bei mitteltiefen Bohrungen. Wie viele Bohrer sind in einer Verpackungseinheit enthalten? Die Verpackungseinheit umfasst 5 Stück des MetavCUT Spiralbohrers mit der SKU 40080-FDA.
8mm HSS-Co Spot Weld Drill 44mm Total Length Vario Drill, Profile Ground - TECWERK
Take advantage of a drill that combines HSS‑Co cutting performance with DIN 1897 dimensions for consistent fitment and burr‑free results; order via Metav Werkzeuge or consult their specialists for application advice and availability. TECWERK Spot Weld Drill D.8 × L.44 mm — HSS‑Co, Vario shank TECWERK Spot Weld Drill D.8 × L.44 mm designed for precision removal of spot welds in sheet metal and repair applications HSS‑Co for high wear resistance DIN 1897 dimensions ensure interchangeability Profile‑ground for precise cutting edges Right‑hand cutting with self‑centering tip Vario cylinder shank for versatile clamping Precise, burr‑free spot weld removal for efficient rework The drill delivers burr‑free extraction of spot welds thanks to its self‑centering tip and finely profile‑ground flutes, which guide the tool cleanly through sheet metal without tearing. For workshops handling welding repairs or bodywork, this results in reduced secondary finishing and shorter cycle times. The adherence to DIN 1897 ensures consistent mounting and repeatable results when used with compatible chucks and holders, supporting predictable process planning and fewer tool changes. Improved cutting life and stable performance under load Manufactured from HSS‑Co, the tool combines cobalt alloy toughness with hardened microstructure for enhanced heat resistance and fracture toughness during intermittent grinding or drilling through welded joins. The profile‑ground geometry provides a sharper cutting edge and improved chip evacuation, which lowers feed forces and contributes to longer service life. These characteristics translate into measurable cost efficiency by reducing consumable turnover and downtime in small to medium production environments. Flexible clamping and straightforward integration into existing tooling The Vario cylinder shank format allows secure clamping in a wide range of toolholders and drill chucks, enabling rapid integration into standard workshop equipment. The combination of a straight cylinder shank with the standardised dimensions guarantees compatibility and simple replacement routines, which minimises setup effort. For technicians seeking a compact, reliable option for spot‑weld extraction, the design supports quick changeovers and consistent concentricity during operation. Practical handling, recommended parameters and safe working For best results, moderate feed and controlled speeds are advised to preserve the cutting edge and avoid workpiece distortion; intermittent cutting with coolant can further improve tool life. The drill is optimised for sheet metal spot welds and similar joining points; secure clamping of the workpiece and use of appropriate extraction methods prevent rework and improve workplace safety. Regular inspection of the cutting geometry will detect wear early and maintain the precision of subsequent operations. For reliable, burr‑free spot‑weld removal order the TECWERK Spot Weld Drill via Metav Werkzeuge — Metav Werkzeuge provides application guidance and fast delivery from Emmerich; contact info@metav-werkzeuge.com or call +49 2822 7131930 for tailored advice and stock information Technical Data Article number: 2000860128NW Name: Schweißpunktbohrer D.8xGesamt-L.44mm HSS-Co Vario Drill Manufacturer: TECWERK Facts Diameter: 8 mm Overall length: 44 mm Special features Material: HSS‑Co Standard: DIN 1897 Profile: profile‑ground (profilgeschliffen) Cutting direction: right‑hand cutting (rechtsschneidend) Tip: self‑centering centre point (selbstschneidende Zentrumsspitze) Shank: Vario cylinder shank (Zylinderschaft, Schaftausführung Vario Drill) Application: precise, burr‑free removal of spot welds (exaktes gratfreies Ausbohren von Schweißpunkten) FAQ What materials is this drill suitable for? The TECWERK Spot Weld Drill D.8 × L.44 mm, made from HSS‑Co, is designed primarily for sheet metal and welded joints and is optimised for typical spot weld extraction tasks. How does the Vario shank affect compatibility? The Vario cylinder shank allows the drill to be clamped in a wide range of standard chucks and holders, making the TECWERK Spot Weld Drill suitable for many workshop setups. What benefit does the DIN 1897 designation provide? DIN 1897 compliance ensures standardised dimensions for the drill, so the TECWERK tool fits consistently in equipment that follows the same standard, aiding repeatability. Is coolant recommended when using this drill? Using a suitable coolant or intermittent cutting can extend the service life of the TECWERK Spot Weld Drill by reducing heat build‑up and improving chip evacuation. What maintenance keeps the drill performing well? Regular inspection of the cutting edges and prompt replacement when wear is visible will maintain the precision of the TECWERK Spot Weld Drill and avoid inferior hole quality. Manufacturer/Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund
8mm HSS-E Twist Drill DIN 338 ,short, 5% cobalt-alloyed, Type N - MetavCUT
Twist Drill (Spiralbohrer) — Type N short · 8 mm · 135° · HSS‑E · DIN 338 · 5% cobalt‑alloyed · Fully Ground — MetavCUT The Twist Drill Type N short 8 mm is a precision metal‑drilling bit for use in a Drilling Machine, designed for stable, accurate holes in hard materials. Short design for improved stability and precision 8 mm HSS‑E geometry for hard and alloyed steels 135° point angle for reduced walking in stainless steel Fully ground shaft for high concentricity and clean holes Manufactured to DIN 338 for metal machining reliability Precise material and cutting performance for demanding metalwork This short Twist Drill is made from HSS‑E (High Speed Steel with cobalt) and features a 5% cobalt‑alloyed composition that increases hot hardness and wear resistance. The shorter overall length reduces cantilever action, which directly improves stability and reduces the risk of deflection during machining. For operators who require consistent hole quality in tough materials, the cobalt‑enriched steel provides longer tool life under elevated temperatures compared with standard HSS. Designed for stable, accurate drilling in hard materials The Type N geometry with a 135° point angle is optimised for harder substrates such as stainless steel and alloyed steels; the flatter point decreases the tendency to dig in and shortens the initial plunge time. Because the bit is fully ground, it delivers excellent runout accuracy and very sharp cutting edges, resulting in cleaner holes with minimal burr formation. These characteristics are particularly valuable for precision work on components where hole accuracy matters. Practical advantages and typical uses in workshops Short twist drills to DIN 338 are especially suited to bench and machine drilling operations where rigidity is available—examples include drilling in alloyed and unalloyed steel, cast iron, non‑ferrous metals and certain plastics. The reduced overhang makes setup easier and safer on both stationary and portable drilling equipment. Users benefit from fewer broken tools when observing recommended feeds, speeds and adequate cooling, particularly for diameters below 6 mm; for the 8 mm size here, appropriate cooling extends life and improves surface finish. Recommendations for machining and tool handling When using this short, fully ground twist drill, clamp the workpiece securely and use a Drilling Machine with proper alignment. Start with a centre or pilot mark when high positional accuracy is required and apply cutting fluid for prolonged tool life when machining stainless or high‑strength alloys. The rolling or grinding manufacturing method affects regrindability: fully ground bits offer superb initial sharpness and repeatable geometry, but they can be more brittle—regrind carefully and avoid excessive heat build‑up during sharpening. MetavCUT recommends this short HSS‑E Twist Drill for precision metal applications; for personalised advice or additional technical data contact METAV Werkzeuge at info@metav-werkzeuge.com, phone +49 2822 7131930 or WhatsApp +49 170 2837271 — expert consultation is available. Designation: Twist Drill Brand: MetavCUT SKU: 47080-FDA Diameter: 8 mm Spiral Length: 75 mm Overall Length: 117 mm Point Angle: 135° Type: Type N Material: HSS‑E (High Speed Steel with cobalt) Finish / Version: short Shaft Finish: fully ground Colour / Alloy: 5% cobalt‑alloyed For Use In: Drilling Machine Norm: DIN 338 Model Series: Standard Line Application: Drills for metal Manufacturer: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What materials is the Twist Drill by MetavCUT Type N suitable for? The MetavCUT Twist Drill Type N is intended primarily for metalworking: alloyed and unalloyed steels, cast iron, non‑ferrous metals and certain plastics; the HSS‑E composition and 135° point angle improve performance when machining harder materials. How should I use the MetavCUT Twist Drill Type N to maximise tool life? For best results with the MetavCUT Twist Drill Type N, secure the workpiece, use correct spindle speed and feed for 8 mm HSS‑E, and apply cutting fluid when machining stainless or high‑temperature alloys to reduce wear and avoid overheating. What is a Twist Drill used for? A Twist Drill is mainly applied when machining high‑strength materials and larger diameters; this form is easy to regrind and withstands higher loads. Which three drill types exist? The three main drill categories are metal drills, wood drills and stone/concrete drills. Why are twist drills point‑sharpened? Point sharpening reduces the cross‑cut at the tip, significantly lowering friction so that reduced feed forces are sufficient; it also improves initial centring of the tip in the workpiece. Can a metal drill be used to drill wood? A metal drill can be used in wood, but guidance is poorer and the hole finish is less clean; however, metal drills are easier to resharpen and show less self‑feeding. At which drilling depths is the twist drill most commonly used? Solid drilling with a twist drill is standard for hole diameters up to about 20 mm and drilling depths up to roughly 100 mm; it is the most frequently used tool for these ranges. Is HSS or HSSE better? The common belief that HSSE is always superior to HSS is incorrect; you should assess whether working conditions justify the higher cost of HSSE for your specific application.
8mm HSS-G Body Drill ,double sided, black finished without margin - MetavCUT
Body Drill (Twist Drill) by MetavCUT — HSS‑G double sided, Ø 8 mm, 135°, black finished without margin, fully ground shank, total length 79 mm, spiral length 20 mm The Body Drill (Twist Drill) is a double‑ended HSS‑G metalworking drill designed for precision holes in alloyed and unalloyed steels using a Drilling Machine. Double‑ended design for two usable tips CNC‑ground geometry for precise, clean holes 135° tip angle for hard metals like stainless steel Fully ground shank for high runout accuracy High performance drilling for demanding metalwork Designed for professionals, this HSS‑G Twist Drill delivers reliable performance when accuracy counts. The CNC‑ground flute geometry produces sharp cutting edges and reduces required feed force by up to 50% compared with conventional HSS types, which allows faster penetration and less operator fatigue. The 135° tip angle shortens start time on hard materials and improves centring on tough surfaces, making it particularly suitable for alloyed steel and cast materials. Durable design that keeps downtime low A short, double‑ended configuration provides practical resilience: if one end dulls, the bit can be reversed and reused, effectively offering two cutting tips in one tool. The fully ground shank enhances concentricity and reduces runout, resulting in cleaner holes and less rework. For stationary machining or cooled drilling cycles the construction offers consistent edge life, while the black finished surface improves corrosion resistance during storage. Practical guidance for application and tool choice This Twist Drill is optimised for metal applications such as thin sheet, rivet holes and small component bores, and it pairs best with a stable Drilling Machine at appropriate speeds and coolant. For hand‑held drills, ensure a secure chuck and controlled feed as the ground geometry is sharper and can be more brittle than rolled types. Use cutting fluid for prolonged tool life when working with stainless or tempered steels to avoid premature wear. Who benefits from this tool and how to use it safely Machinists, bodywork specialists and metal fabricators benefit most from this bit’s combination of precision and serviceability. The double‑ended design suits repetitive shop tasks where quick tip rotation reduces tool change time. When drilling, start with a light pilot feed to improve centring; the larger point angle reduces walking on hard surfaces. Follow standard safety and cooling practices to mitigate brittleness risk and extend cutting life. Strong recommendation: choose the MetavCUT Body Drill (Twist Drill) when you need precision, durability and the convenience of a double‑ended HSS‑G solution — for expert product advice and application support contact METAV Werkzeuge. Are you unsure if this tool fits your task or need further technical data? METAV Werkzeuge offers comprehensive advice: 📧 info@metav-werkzeuge.com ☎️ +49 2822 7131930 ✔️ WhatsApp: +49 170 2837271 Designation: Body Drill (Twist Drill) Brand: MetavCUT SKU: 59080-FDA Diameter: 8 mm Point angle: 135° Type: double sided (double‑ended) Colour/Finish: black finished without margin Application: Drills for metal / Drill for Metal Spiral length: 20 mm Total length: 79 mm Shank execution: fully ground Material: HSS‑G For drilling machine: Drilling Machine Model series: Profi Line Packaging unit: 10 Manufacturer: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What is a Twist Drill used for? The MetavCUT Body Drill (Twist Drill) is primarily applied to the machining of high‑strength materials and larger hole diameters; its shape allows easy resharpening and it withstands greater loads, making it suitable for alloyed and unalloyed steel, cast steel and hard plastics. Which three drill types exist? The three main drill types are metal drills, wood drills and masonry/concrete drills; the MetavCUT Body Drill belongs to the metal drill category optimised for metalworking. Why are Twist Drills pointed? The point sharpening reduces the cross‑cut at the tip, lowering friction and required feed forces while improving centring in the workpiece; this is why the MetavCUT double‑ended HSS‑G bit uses a 135° point for better performance in harder materials.
8mm HSS-G Twist Drill DIN 1869 ,extra long, bright finished - MetavCUT
Twist Drill — Extra Long HSS‑G Drill (Ø 8 mm, 135° Tip, Bright Finished, Fully Ground Shank, DIN 1869) A Twist Drill designed for deep metal drilling in Drilling Machines, offering an extra long length and a 135° tip for reliable penetration. Ø 8 mm for precise hole diameters Extra Long design for deep or hard‑to‑reach holes HSS‑G material for high wear resistance 135° tip angle for harder materials Fully Ground shank for high runout accuracy Exceptional deep‑hole performance for demanding metalwork This extra long HSS‑G Twist Drill is engineered to reach depths that standard drills cannot. The extended overall length and increased spiral length allow clean chip evacuation during deep drilling, reducing the need to retract frequently. As a result, the tool achieves efficient progress in tasks such as structural steel or thick plate drilling, where depth and steady feed are crucial. The DIN 1869 compliance guarantees suitable geometry for deeper holes under challenging conditions. Faster cutting with lower feed forces thanks to precision grinding A fully ground geometry and CNC‑refined flutes give the bit a sharp profile that cuts more efficiently. The ground design enables up to 40% faster drilling and requires significantly less axial force compared with rolled HSS bits, which is particularly beneficial for handheld or smaller drilling machines where operator control matters. The 135° Tip improves centring and reduces walking on hard substrates, helping to produce cleaner bores with less rework. Robust material choice and targeted applications Made from HSS‑G, this Twist Drill is suited for alloyed and unalloyed steel, cast steel, grey cast iron, sintered iron, non‑ferrous metals and hard plastics. The material selection balances hardness and toughness for high performance in metalworking. For stationary drilling with coolant and controlled feeds the bit excels; note that ground drills can be more brittle, so proper clamping and cooling extend tool life and maintain hole quality. Designed for accuracy and machine compatibility The bright finished surface and fully ground shank ensure consistent clamping and minimal runout, supporting precise machining outcomes. The geometry tailored by the DIN 1869 standard promotes repeatable centring and stability in common Drilling Machines. Users seeking clean, concentric holes with reduced radial deviation will benefit from the bit's tight manufacturing tolerances and sharp cutting edges. Strongly recommended: Choose the MetavCUT Twist Drill for deep metal drilling and contact METAV Werkzeuge for expert technical advice — Email info@metav‑werkzeuge.com | Tel +49 2822 7131930 | WhatsApp +49 170 2837271 Technical Information Designation: Twist Drill Brand: MetavCUT SKU: 32080‑FDA Diameter: 8 mm Tip Angle: 135° Execution / Type: Extra Long Colour / Finish: Bright Finished Shank Execution: Fully Ground Material: HSS‑G Standard: DIN 1869 Spiral Length: 165 mm Overall Length: 240 mm Application: Drills for metal For Machine Type: Drilling Machine Model Series: Standard Line Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What materials is the MetavCUT Twist Drill suitable for The MetavCUT Twist Drill is intended primarily for metals such as alloyed and unalloyed steel, cast steel and grey cast iron; it is also usable in non‑ferrous metals and hard plastics, delivering accurate holes when used with appropriate coolant and feed rates. How should the MetavCUT Twist Drill be used to maximise tool life For best results with the MetavCUT Twist Drill, use steady feeds, adequate clamping and cutting fluid for heat removal; the ground HSS‑G geometry cuts efficiently but benefits from controlled machining conditions to avoid chipping. For what is a Twist Drill used A Twist Drill is mainly applied when machining high‑strength materials and larger diameters. This form is easy to regrind and withstands higher loads while enabling deep, precise holes under demanding conditions. Which three drill types exist There are three main drill types: Metal drills, Wood drills and Stone/Concrete drills. Why are Twist Drills pointed Pointing reduces the cross‑cut at the tip. By re‑pointing, friction forces are significantly lowered so that less feed force is required and the tip centres more reliably in the workpiece. Can a Twist Drill be used for wood A metal Twist Drill can be used in wood but offers poorer guidance and a less clean finish; however, these drills are easier to regrind and have less aggressive self‑feeding than specialised wood bits. At which depths is the Twist Drill most used A through hole in solid material is typically made with a Twist Drill. For diameters up to 20 mm and drilling depths up to 100 mm, the Twist Drill is the most commonly used tool.
8mm HSS-G Twist Drill DIN 1869 ,extra long, bright finished - MetavCUT
Twist Drill — 8 mm, 135° Point Angle, Extra Long, Bright Finished, HSS-G (DIN 1869) by MetavCUT The Twist Drill is an extra long Twist Drill designed for deep metal drilling with a 135° point angle for use in Drilling Machines. 8 mm Diameter for precise metal drilling Extra-Long Design for deep or hard-to-reach holes 135° Point Angle for harder materials HSS-G Fully Ground for fast, accurate cuts DIN 1869 Standard for deep-hole drilling reliability Drill Deeper with Consistent Precision The Twist Drill Extra-Long construction provides an extended Overall Length of 305 mm and a Spiral Length of 210 mm, enabling reliable Deep Drilling where standard tools fall short. This geometry is especially useful when access is limited or when holes must be made from a greater distance; the Longer Reach reduces the need for extensions and preserves alignment. The 8 mm Diameter maintains good rigidity while allowing fine control, so each hole stays true and Repeatable even at depth. Built for Hard Materials and Stable Entry Equipped with a 135° Point Angle, this Twist Drill penetrates harder materials with reduced walking and improved centring. The HSS-G Material and CNC grinding process create very sharp cutting edges and high Roundness Accuracy, producing clean bore surfaces in alloyed and unalloyed Steel, Cast Steel, Grey Cast Iron and Non-Ferrous Metals. Note that the ground geometry offers excellent precision but requires appropriate coolant and often stationary or guided use to avoid brittle breakage. Faster Drilling with Lower Feed Forces The Fully Ground flute geometry of this Drill allows up to 40% faster drilling and can require up to 50% less feed force compared with conventional rolled HSS designs. This reduction in Thrust improves operator comfort and extends tool life under the right conditions. Conforming to DIN 1869, the deep-spiral form supports effective chip evacuation during long bores and reduces the risk of chip packing that can stall the cut. Reliable Choice for Workshop and Production Use Designed for use in Hand Drills and Drilling Machines, the MetavCUT Extra-Long Twist Drill suits workshop environments and stationary machines where repeatability and reach matter. Professionals who machine thicker components or require access past fixtures will value the combination of Precision and Reach. The Standard Line modelling focuses on robust everyday performance and predictable results in series or single-part production. MetavCUT recommends this Twist Drill for demanding deep-hole metalworking tasks — for expert advice and to verify suitability for your application, contact METAV Werkzeuge: info@metav-werkzeuge.com | Tel +49 2822 7131930 | WhatsApp +49 170 2837271 Designation: Twist Drill Brand: MetavCUT SKU: 33080-FDA Diameter: 8 mm Point Angle: 135° Type / Execution: Extra Long Colour / Finish: Bright Finished Shank Execution: Fully Ground Material: HSS-G Standard: DIN 1869 Overall Length: 305 mm Spiral Length: 210 mm For Machine: Drilling Machine Model Series: Standard Line Application: Drills for metal Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ For what is the Twist Drill used? The MetavCUT Twist Drill is primarily applied for machining high-strength materials and larger bore diameters; it performs well in alloyed and unalloyed Steel, Cast Steel and Non-Ferrous Metals. Its ground spiral geometry is easy to regrind and withstands higher loads, making it suitable for demanding metalworking tasks. Which three drill types exist? In general tool classification you will find Metal Drills, Wood Drills and Stone/Concrete Drills; the MetavCUT Twist Drill belongs to the Metal Drill group and is optimised for metalworking applications. Why are Twist Drills pointed? The pointing reduces the cross-cut at the tip of the Twist Drill, significantly lowering friction and therefore the required feed force; this sharpening also improves centring of the tip in the workpiece for a more accurate start. Can a Twist Drill be used to drill wood? A Metal Drill such as the MetavCUT Twist Drill can be used in Wood, but guidance and finish are inferior compared with wood-specific bits. Metal Drills are easier to resharpen and have less self-feeding action, so results in Wood are acceptable but not optimal. For which drilling depths is the Twist Drill most commonly used? A full-penetration bore is often executed with a Twist Drill; for diameters up to 20 mm and depths up to 100 mm this type of tool is the most frequently used option for reliable deep-hole drilling. What is better, HSS or HSSE? The common assumption that HSSE steels are universally superior to HSS is not correct. When choosing, evaluate whether the specific work conditions justify the higher cost of HSSE; MetavCUT supplies HSS-G variants that balance performance and economy for many metalworking tasks.
8mm HSS-G Twist Drill DIN 1869 ,extra long, bright finished - MetavCUT
Twist Drill — 8 mm, 135° Tip Angle, Extra Long • Bright Finished • HSS‑G • DIN 1869 The Twist Drill is an extra‑long HSS‑G metal drill for deep, precise holes with a Drilling Machine, optimised for hard materials and demanding shop use. Extra‑long design for deep drilling CNC‑ground HSS‑G for precise, clean holes 135° Tip Angle suited for hard materials Fully ground shank for excellent concentricity Consistent deep-hole performance for demanding metalwork The MetavCUT extra‑long design delivers reliable drilling when access is restricted or when through‑holes must be produced without multiple setups. With a Total Length 390 mm and a Spiral Length 265 mm, this twist drill enables drilling of extended depths while maintaining steady chip evacuation. The elongated geometry reduces the need for extensions or stepped drilling, which saves time in production and lowers fixture complexity. For machinists seeking reproducible deep holes, the geometry is designed to balance stiffness and Reach. Sharp geometry and material for hard, alloyed steels Made from HSS‑G and finished by CNC grinding, the bit combines toughness with cutting precision. The 135° Tip Angle reduces cutting forces in harder materials such as stainless and tempered steels, improving centring and lowering the risk of workpiece deformation. Grinding the Flutes produces a sharp cutting edge and high runout accuracy, which results in cleaner bores and more consistent hole tolerances. For operators less familiar with grind types: CNC grinding means the Flute geometry is cut rather than rolled, giving higher Dimensional Precision at the cost of slightly increased brittleness — therefore cooling and appropriate speeds are recommended. Recommended applications, handling and compatibility This metal drill is intended for drilling in legated and unlegated Steel, Cast Iron, Non‑Ferrous Metals and Hard Plastics under workshop conditions. It is optimised for use in a Drilling Machine and benefits from controlled speeds, steady feed and coolant for prolonged life. The Fully Ground Shank improves clamping concentricity in chucks, reducing runout and vibration. As a practical tip: when working deep, ensure adequate Chip Evacuation and periodic pecking or coolant supply to prevent clogging and premature wear. Choose the MetavCUT Twist Drill for demanding deep metal drilling — for technical advice or to check suitability for a specific application contact METAV Werkzeuge: info@metav-werkzeuge.com • +49 2822 7131930 • WhatsApp +49 170 2837271 Bezeichnung: Twist Drill Marke: MetavCUT Diameter: 8 mm Total Length: 390 mm Spiral Length: 265 mm Tip Angle: 135° Execution: Extra long Colour / Finish: Bright finished Shank: Fully ground Material: HSS‑G Standard: DIN 1869 Application: Drills for metal / for Drilling Machine Model Series: Standard Line Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What is the MetavCUT Twist Drill best used for? The MetavCUT Twist Drill (metal Twist Drill) is primarily designed for machining high‑strength and alloyed steels and larger bore diameters; its extra‑long design and HSS‑G material make it suitable for deep holes and applications requiring precise hole geometry. Can the MetavCUT Twist Drill be used in a bench or handheld drill? The MetavCUT Twist Drill is optimised for use in a Drilling Machine; it can be used in powerful benchtop machines but, due to its length and ground construction, handheld use is not recommended for safety and accuracy reasons. For what is a Twist Drill used? A Twist Drill is mainly applied when machining high‑strength materials and large bore diameters. Its form allows relatively easy regrinding and it endures higher loads, making it suitable for tough metalworking tasks. Which three drill types exist? Common categories are Metal Drill, Wood Drill and Masonry/Concrete Drill. Why are twist drills pointed? Pointing reduces the cross‑edge at the tip of the twist drill. By pointing, friction forces are significantly lowered so reduced feed forces are required, and the tip centres better in the workpiece. Can you drill wood with a metal twist drill? A metal drill can be used in wood, but guidance is poorer and hole quality is inferior. Metal bits are easier to regrind and have less self‑feed, so results may be acceptable for non‑critical wooden applications. At which drilling depths is the twist drill most used? Twist Drills are the standard tool for through holes and are most commonly used up to diameters of about 20 mm and drilling depths up to 100 mm; extra‑long variants extend that capability for deeper bores. Which is better, HSS or HSSE? The general assumption that HSSE is always superior to HSS is incorrect. Evaluate working conditions carefully to determine whether the higher cost of HSSE is justified for the required application.
8mm HSS-G Twist Drill DIN 338 ,fully ground, silver - MetavCUT
Twist Drill — Drill Bit, Diameter 8 mm, 118° Tip Angle, HSS‑G, Fully Ground, Silver, DIN 338 The Twist Drill is a precision Drill Bit for metalworking, offering an 8 mm Diameter and a 118° Tip Angle for reliable centring and clean holes in a variety of metals. Ideal for metalworking applications with high precision Fully ground geometry for faster, cleaner drilling Hexagonal shank for secure torque transmission Conforms to DIN 338 for standardised short Twist Drills Suitable for use in Drilling Machines and handheld drills Faster, cleaner holes thanks to fully ground geometry The Twist Drill uses a Fully Ground HSS‑G construction that produces very sharp cutting edges and high runout accuracy. This manufacturing method (CNC grinding) enables up to 40% faster drilling and requires approximately 50% less feed force compared with rolled HSS bits, which translates into less operator fatigue and shorter cycle times. The grounded flute geometry also yields cleaner, more precise holes particularly in alloyed and unalloyed steel and other hard materials. Secure clamping and improved torque transfer with a hexagonal shank A Hexagonal Shank (sechskant) ensures form‑fit torque transmission into Bit Holders and quick‑change chucks, reducing slippage during heavy cutting. The shank design allows direct use in 1/4" bit holders (E6.3) while remaining compatible with standard chucks, which simplifies tool changes and increases workplace efficiency. For mobile setups and cordless drivers, the hex shank provides safer engagement under higher loads. Material choice and geometry tuned for metalworking Made from HSS‑G (high speed steel, ground), the bit offers a balance of hardness and toughness for drilling metals such as steel, cast iron, non‑ferrous metals and certain engineering plastics. The 118° Tip Angle favours easier penetration and better centring in softer metals like aluminium, while the overall bit geometry remains versatile for a wide range of workshop tasks. Note that fully ground HSS can be more brittle than rolled variants; therefore, recommended use is with adequate cooling and in appropriate drilling setups to maximise service life. Practical use cases and handling recommendations Experienced machinists and maintenance technicians will appreciate the combination of DIN 338 conformity and standardised lengths that support repeatable setups on both stationary and portable machines. For best results, use the correct cutting speed for the material and apply coolant when machining harder alloys. The bit is well suited to production tasks and repair work where precision and repeatability are required rather than rough or one‑off woodworking applications. For precision metalworking applications choose the MetavCUT Twist Drill for reliable performance — for expert advice or to confirm suitability contact METAV Werkzeuge by eMail: info@metav-werkzeuge.com, phone: +49 2822 7131930 or WhatsApp: +49 170 2837271 Designation: Twist Drill Brand: MetavCUT SKU: 57080-FDA Diameter: 8 mm Tip Angle: 118° Material: HSS-G Execution: fully ground Colour: silver For Drilling Machine: Drilling Machine (Handbohrmaschine) Spiral Length: 70 mm Shank: Hexagonal Overall Length: 135 mm Norm: DIN 338 Model Series: Standard Line Application: Drills for metal Manufacturer: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What materials is the MetavCUT Twist Drill suitable for? The MetavCUT Twist Drill, a precision Drill Bit made from HSS‑G, is intended primarily for metalworking and performs well in alloyed and unalloyed steels, cast iron, non‑ferrous metals and some hard plastics; for the hardest materials, follow recommended speeds and cooling practices. How should the MetavCUT Twist Drill be clamped and operated for best life? Clamping the MetavCUT Twist Drill in a properly sized chuck or a 1/4" bit holder for the Hexagonal Shank ensures secure torque transfer; use correct cutting speeds, steady feed and coolant as needed to reduce wear and avoid brittle failure. What is a Twist Drill used for? A Twist Drill is mainly applied when working on high‑strength materials and larger drill diameters; the ground flute geometry makes it easier to grind and yields precise holes that withstand higher loads. Which three drill types are there? The main drill types are Metal Drills, Wood Drills, and Stone/Concrete Drills. Why are Twist Drills point‑sharpened? Point‑sharpening reduces the chisel edge at the tip, significantly lowering friction and thus the required feed forces, while improving centring of the bit in the workpiece. Can a Metal Drill be used in Wood? A Metal Drill can be used in Wood, but it offers less guidance and a less clean finish compared with dedicated wood bits; however, such drills are easier to resharpen and have lower self‑feeding tendency. For which drilling depths is the Twist Drill most commonly used? A solid bore is typically executed with a Twist Drill; for diameters up to 20 mm and drilling depths up to 100 mm, the Twist Drill is the most commonly used tool. Is HSS or HSSE better? The common belief that HSSE is always superior to HSS is not universally true; decide based on your specific working conditions to determine whether the higher cost of HSSE is justified.
8mm HSS-G Twist Drill DIN 338 ,left cutting - MetavCUT
Hohe Bohrleistung und reduzierte Anpresskraft machen den MetavCUT Profi Line Spiralbohrer zur effizienten Wahl für anspruchsvolle Metallbearbeitung; die linksschneidende Ausführung erleichtert zudem das Ausbohren festsitzender Schrauben. Profitieren Sie von HSS‑G Material, 135° Spitzenwinkel und der Normkonformität nach DIN 338 für sichere Ergebnisse und unkomplizierten Einsatz, bestellen Sie den Bohrer direkt über Metav oder fragen Sie unsere Beratung bei Bedarf an. Spiralbohrer – MetavCUT Profi Line Der Spiralbohrer von MetavCUT ist ein kurzer HSS‑G‑Bohrer, linksschneidend und spezialisiert auf Metallbohrungen sowie das Ausbohren festsitzender Schrauben. Kurzer HSS‑G‑Bohrer nach DIN 338 Linksschneidend für Ausbohren festsitzender Schrauben Spitzenwinkel 135° für harte Werkstoffe Für Handbohrmaschine geeignet, Zylinderschaft Verpackungseinheit 10 Stück industrielle Qualität Dauerhafte Schneidleistung durch HSS‑G für konstante Produktivität Der Einsatz von HSS‑G sorgt für hohe Zähigkeit und thermische Beständigkeit bei Bohrvorgängen in Stahl und Gusswerkstoffen. Weil das Material höhere Temperaturen und Belastungen aushält, bleibt die Schneideform länger erhalten, wodurch weniger Nachschärfen nötig ist und Ausfallzeiten reduziert werden. Ein konkreter Nutzen ist die verlängerte Standzeit bei Serienarbeiten, die Kosten pro Bohrung senkt und die Effizienz in der Werkstatt erhöht. Linksschneidend: Spezifische Lösung für festsitzende Schrauben und schwierige Fälle Die linksschneidende Ausführung ist speziell dafür gedacht, bei Linkslauf gebrochene Schrauben zu lösen und Ausbohrungen zu erleichtern. In Kombination mit moderater Kühlung und kontrolliertem Vorschub reduziert sich die Gefahr von Verkanten und Bruch. Anwender profitieren von einer höheren Treffergenauigkeit beim sicheren Entfernen von Schraubenresten und von kürzeren Rüstzeiten bei Reparaturarbeiten. Präzision und Normkonformität für industrielle Anforderungen Die Einhaltung der DIN 338 gewährleistet reproduzierbare Abmessungen und Schaftgeometrie, was den sofortigen Einsatz in definierten Spannsystemen ermöglicht. Der 135° Spitzenwinkel wurde gewählt, um das Anbohren in harten Werkstoffen zu erleichtern und die Zentrierkraft zu erhöhen. Für Anwender bedeutet dies weniger Ausläufer beim Ansetzen und eine zuverlässigere Maßhaltigkeit bei Passungen und Nachbearbeitung. Praxistipps für sicheren Einsatz und hohe Prozesssicherheit Mit einem Durchmesser von 8 mm fällt der Bohrer in den Standardbereich für Werkstattanwendungen; vorbohren ist in der Regel nicht erforderlich, bei hoher Genauigkeit empfiehlt sich jedoch Anpunkten mit einem Zentrierbohrer. Die Verwendung einer Handbohrmaschine mit Linkslauf wird vorausgesetzt, wenn die linksschneidende Funktion genutzt werden soll. Kühlemittelgabe und moderate Drehzahlen verlängern die Standzeit und reduzieren das Risiko von Überhitzung. Sichern Sie sich den MetavCUT Profi Line Spiralbohrer für präzise Metallbearbeitung direkt bei Metav – bei Fragen stehen wir per E‑Mail info@metav-werkzeuge.com oder Telefon +49 2822 7131930 zur Verfügung. Produktmerkmale Artikelnummer: 60080-FDA Marke: MetavCUT Bezeichnung: Spiralbohrer Serie: Profi Line Fakten Durchmesser: 8 mm Spitzenwinkel: 135° Verpackungseinheit: 10 Besonderheiten Material: HSS-G (Schnellarbeitsstahl, gehärtet) Norm: DIN 338 (kurze Spiralbohrer mit Zylinderschaft) Ausführung: linksschneidend (Anwendung: Ausbohren festsitzender Schrauben) Für Bohrmaschine: Handbohrmaschine SKU: 60080-FDA FAQ Wie unterscheidet sich der MetavCUT Profi Line Spiralbohrer von Standardbohrern? Der MetavCUT Profi Line Spiralbohrer verfügt über HSS‑G Material und eine linksschneidende Geometrie; dadurch bietet er erhöhte Standzeit und spezielle Einsatzmöglichkeiten beim Ausbohren festsitzender Schrauben im Vergleich zu konventionellen HSS‑Bohrern. Kann ich den Bohrer mit einer gewöhnlichen Akku‑Bohrmaschine verwenden? Der Bohrer ist für die Verwendung mit einer Handbohrmaschine vorgesehen; für die linksschneidende Funktion ist jedoch eine Bohrmaschine mit Linkslauf erforderlich, sonst entfällt der Vorteil beim Ausdrehen von Schraubenresten. Für welche Werkstoffe ist dieser Bohrer geeignet? Der MetavCUT Profi Line Spiralbohrer eignet sich für legierte und unlegierte Stähle, Gussstahl, Gusseisen, Sintereisen, Temperguss, Nichteisenmetalle und Hartkunststoffe, wobei HSS‑G die thermische Belastung bei Metallbearbeitung verbessert. Welche Vorteile bietet der Spitzenwinkel von 135°? Ein Spitzenwinkel von 135° reduziert das Wandern beim Anbohren harter Werkstoffe und verbessert die Zentrierung, wodurch besonders bei Edelstahl und gehärteten Stählen das Eindringen erleichtert wird. Ist der Bohrer einzeln oder nur im Zehnerpack erhältlich? Dieser Artikel wird als Verpackungseinheit mit 10 Stück angeboten; Details zur Verfügbarkeit und Einzellieferung erhalten Interessenten über Metav direkt.
8mm HSS-G Twist Drill DIN 338 ,short, bright finished, Type N - MetavCUT
Twist Drill Type N short – 8 mm, HSS‑G, 135°, bright finished (DIN 338) by MetavCUT The Twist Drill Type N short is a high‑performance metal drilling bit for drilling machines, designed for precise, stable holes in steel and other hard materials. Short design for high stability when drilling metal Ground HSS‑G for up to 40% faster drilling 135° tip angle optimised for harder materials Fully ground shank for secure clamping and concentricity Faster, easier drilling thanks to ground HSS‑G and optimized geometry The HSS‑G construction of this Twist Drill delivers tangible productivity gains: the ground High‑Speed Steel enables up to 40% faster drilling while requiring around 50% less feed force than conventional HSS tools. With an 8 mm Diameter and a 135° Tip Angle, this bit penetrates hard materials more reliably, reducing dwell time and wear on the tool. For professionals focused on cycle time and repeatable results, the combination of material and geometry translates directly into increased throughput and lower operator effort. Stable, precise holes from the short design and fully ground shank A shorter Overall Length and a fully ground shank improve rigidity and reduce deflection during drilling. This Twist Drill’s compact execution is particularly suitable for work on lathes, milling centres and hand drilling machines where tool overhang must be minimised. The result is cleaner hole walls and better positional accuracy, which benefits fabrication, assembly and maintenance tasks that demand tight tolerances. Built for metalworking — Type N normal spiral explained This Type N Normal Spiral is the classic configuration for metal drills and was chosen for its balanced chip evacuation and cutting action. According to DIN 338, the short design with a cylindrical shank is intended for robust, stationary or portable drilling in metal. For users less familiar with the terminology: Type N means a general‑purpose metal drill, and short refers to reduced length for improved stiffness and repeatability. Practical advantages and who benefits most Workshop technicians, maintenance crews and metal fabricators will appreciate the combination of durability and ease of use: the bright finished surface improves initial seating and handling, while the 75 mm Spiral Length and 117 mm Overall Length match typical requirements for through and blind holes in plate and component work. For demanding alloys, cast materials and engineering plastics the tool offers longevity and predictable performance, making it a dependable choice for daily production tasks. MetavCUT recommends this HSS‑G short Type N Twist Drill for professional metalworking — for tailored advice or to confirm suitability for your application contact METAV Werkzeuge: info@metav-werkzeuge.com | +49 2822 7131930 | WhatsApp +49 170 2837271 Technical Data Designation: Twist Drill Brand: MetavCUT SKU: 27080-FDA Diameter: 8 mm Tip angle: 135° Material: HSS‑G Type: Typ N Execution: short Shank finish: fully ground Spiral length: 75 mm Overall length: 117 mm Colour: bright finished For drilling machine: Drilling Machine Standard: DIN 338 Model series: Basic Line Application: Drills for metal Manufacturer: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What are Twist Drills used for? Twist Drills like the MetavCUT Twist Drill Type N are primarily used for the machining of high‑strength materials and for larger drill diameters. The short, ground HSS‑G design makes this Twist Drill robust under heavy loads and suitable for applications where fast penetration and durability are required. Which 3 drill types are there? The main categories are metal drills, wood drills and stone/concrete drills. The MetavCUT Twist Drill belongs to the metal drill group and is optimised for use in metalworking applications.
8mm HSS-G Twist Drill DIN 338 ,short, bright finished, Type N - MetavCUT
Twist Drill by MetavCUT — Type N short, Ø 8 mm, 135° point angle, Bright finished, HSS‑G, DIN 338 The Twist Drill Type N short is a compact HSS‑G drill bit designed for precise metalworking tasks in hand and stationary drilling machines. MetavCUT Twist Drill Type N Ø8 mm Short design for greater stability 135° point angle for hard metals HSS‑G fully ground for precise holes DIN 338 compliant for industrial use Faster, more stable drilling in demanding metalwork Dank der short design reduziert dieser Twist Drill das Auskragen aus dem Bohrfutter und minimiert somit Vibrationen und Verbiegen. Die verringerte Auskraglänge führt zu höherer Stability und damit zu gleichmäßigeren, maßhaltigen Bohrlöchern. Als Folge werden Bearbeitungszeiten verkürzt und die Anforderungen an die Werkzeugspannung im Alltag verringert, was besonders bei wiederholten Serienbohrungen spürbare Produktivitätsvorteile liefert. Sharp, ground geometry for clean, precise holes Die HSS‑G Ausführung mit CNC‑geschliffener Spirale sorgt für sehr scharfe Schneidkanten und hohen Rundlauf. Im Vergleich zu gewalzten Bohrern ermöglicht der Schleifprozess sauberere Spanabfuhr und glattere Bohrflächen, was die Nachbearbeitung minimiert. Diese präzise Geometrie ist besonders vorteilhaft beim Bohren in legierte und unlegierte Stähle, Gusswerkstoffe sowie Hartkunststoffe. Engineered for metals and professional workshop use Dieser Twist Drill des Typs Type N ist nach DIN 338 klassifiziert und wurde primär für Metallbearbeitung konzipiert. Er eignet sich für Temperguss, Gusseisen, Sintereisen, Nichteisenmetalle und legierte Stähle. Für Handwerker, Instandhalter und Metallwerkstätten bedeutet das: ein universelles, robustes Werkzeug für den täglichen Einsatz bei stationären oder mobilen Bohrmaschinen. Practical handling tips for longer tool life Beim Einsatz empfiehlt sich Kühlung und angepasste Schnittgeschwindigkeit, um Bruchgefahr bei geschliffenen HSS‑Bohrern zu reduzieren. Die 135° point angle erleichtert das Anbohren harter Werkstoffe, da der Anbohrvorgang verkürzt wird und die Spitze besser zentriert. Kurze Überhänge und ein sauber gespanntes Werkstück minimieren Feed‑Kräfte und erhöhen die Standzeit des Bohrers. Strong recommendation: Choose the MetavCUT short Twist Drill for precise, high‑stability metal drilling — for personal advice and technical support contact METAV Werkzeuge via info@metav-werkzeuge.com, phone +49 2822 7131930 or WhatsApp +49 170 2837271 Technical data Designation: Twist Drill Brand: MetavCUT SKU: 45080-FDA Diameter: 8 mm Overall length: 117 mm Spiral length: 75 mm Point angle: 135° Type: Type N Execution: short Shank: fully ground Material: HSS‑G Surface / Colour: Bright finished Standard: DIN 338 For: Drilling Machine Model series: Standard Line Manufacturer: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What is the main use of the Twist Drill and for which materials is it suitable? The MetavCUT Twist Drill Type N short is primarily used for drilling in metal; it is designed for high‑strength materials and larger diameters, offering good performance in alloyed and unalloyed steel, cast steel, cast iron and hard plastics. Which three drill types are commonly distinguished? Common drill categories are metal drill bits, wood drill bits and stone/concrete drill bits, with the MetavCUT Twist Drill belonging to the metal drill bit group. Why are twist drills split (point relieved)? The splitting reduces the cross‑cut at the tip, which lowers friction and requires less feed force; additionally, the modified tip improves centring in the workpiece. Can a metal twist drill be used to drill wood? A metal drill bit such as the MetavCUT Twist Drill can be used in wood, but guidance and finish are inferior compared with dedicated wood bits; metal bits are easier to re‑grind and show less self‑pulling. For which drilling depths is a twist drill most commonly used? A through hole in solid material is typically made with a twist drill; for diameters up to 20 mm and drilling depths up to 100 mm, the twist drill is the most frequently used tool. Is HSS or HSSE better for drilling? A general assumption that HSSE steels are always superior to HSS is incorrect; selection should be based on specific working conditions to determine whether the higher price of HSSE is justified.
8mm HSS-G Twist Drill DIN 338 ,short, bright finished, Type N - MetavCUT
Twist Drill — Short Type N, 8 mm · 135° Tip · Bright Finished · HSS-G · DIN 338 by MetavCUT The Twist Drill is a short Type N metalworking drill designed for precision drilling in steels and other hard materials with Drilling Machines. Short HSS-G body for increased stability 135° tip for clean entry in hard materials Fully ground shank for precise chucking Conforms to DIN 338 for consistent dimensions Bright finished surface for smooth chip evacuation Greater Stability and Faster Drilling for Metalworking Short design and HSS-G construction make this twist drill ideal where rigidity matters. Because the overall protrusion from the chuck is reduced, the tool shows less deflection under load, resulting in straighter holes and longer tool life when used correctly. The inherent material properties of HSS-G allow higher cutting speeds compared with conventional HSS, which translates into faster hole making and reduced machining time. For workshop and production environments this means fewer rejects and more consistent process control. Precise Entry and Reduced Burrs with a 135° Tip A 135° point angle significantly improves centring and reduces the tendency to wander on tougher surfaces. This geometry lowers the radial forces during entry, which decreases burr formation and the need for secondary deburring operations. In practice, the Type N spiral geometry combined with the larger tip angle is particularly suited to stainless steels and tempered alloys where a sharper angle would blunt quickly. For engineers and tradespeople, this results in more reproducible hole quality in demanding materials. Exact Fit and Reliable Performance from the Fully Ground Shank The fully ground cylindrical shank ensures superior concentricity in the chuck, improving runout and surface finish of the drilled hole. The fully ground shank also simplifies regrinding and refurbishment, keeping the tool serviceable over several maintenance cycles. The bright finished surface aids chip flow and inspection, helping operators spot wear earlier and maintain process stability. These features together deliver consistent results when mounted in stationary or portable drilling equipment. Optimised Dimensions and Compliance for Industrial Use With a drill Diameter of 8 mm, Spiral Length 75 mm and Overall Length 117 mm, the tool follows the short drill conventions described in DIN 338, giving compatibility with standard tool holders and replacement policies. The combination of short spiral length and robust construction suits applications on both bench and machine tools where precise, repeatable holes in metal are required. For production planners this means easier tool inventory management and predictable cycle times. Who Benefits from This Short HSS Twist Drill Workshops, toolrooms and industrial maintenance teams benefit most from a short, stable drill that performs reliably in steels, cast materials and non-ferrous metals. Because the short twist drill design reduces vibration and improves hole accuracy, it is particularly advantageous for setups with limited clearance or when working on jigged and clamped assemblies. The tool is well suited to both experienced machinists seeking predictable performance and procurement managers who prioritise conformity to standards like DIN 338. Strong recommendation: choose the MetavCUT short HSS-G Twist Drill for precise metal drilling and consult METAV Werkzeuge for tailored technical advice — Email info@metav-werkzeuge.com · Tel +49 2822 7131930 · WhatsApp +49 170 2837271 Designation: Twist Drill (Short Spiralbohrer) Brand: MetavCUT SKU: 48080-FDA Diameter: 8 mm Point Angle: 135° Type: Type N Material: HSS-G Execution: Short Spiral Length: 75 mm Overall Length: 117 mm Shank Finish: Fully ground Surface Finish: Bright finished For Use With: Drilling Machine (Handbohrmaschine) Standard: DIN 338 Applications: Drills for metal Manufacturer: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What makes a short twist drill different from a standard one? A short twist drill such as the MetavCUT Short Type N offers a reduced overhang and therefore higher rigidity compared with standard-length drills. This increases stability and improves hole accuracy in metalworking applications while reducing the risk of drill bending and chatter. Can the MetavCUT Twist Drill be used in a hand drilling machine? The MetavCUT Twist Drill is intended primarily for machine use, but it can be operated in heavy-duty handheld Drilling Machines when the setup is rigid and appropriate coolant is applied. For manual drilling in delicate tasks a dedicated hand-oriented bit may provide easier control. For what is a Twist Drill used? A Twist Drill is mainly used for machining high-strength materials and larger hole diameters. This form is easy to regrind and withstands considerable loads while delivering clean, precise holes suitable for subsequent tapping or finishing. Which three drill types are there? The three main drill types are metal drills, wood drills and stone/concrete drills. Each group is optimised for its material class and differs in point geometry, flute design and substrate material.
8mm HSS-G Twist Drill DIN 338 ,short, TIN-coated - MetavCUT
MetavCUT Twist Drill (Short Twist Drill) — 8 mm, 118°, TIN-coated, Short, DIN 338, HSS-G The MetavCUT Twist Drill is a short Twist Drill designed for precise metalworking with an 8 mm diameter and a 118° point angle for reliable centring in a wide range of metals. MetavCUT Twist Drill short 8 mm TIN-coated for reduced friction and longer life HSS-G fully ground for precise metal drilling 118° Point angle for reliable centring Conforms to DIN 338 for short twist drills Faster, more precise metal drilling with reduced effort The short design delivers higher stability and less deflection compared with longer drills, which translates into cleaner holes and fewer rejects when working with metal. The HSS-G (ground high-speed steel) geometry enables up to 40% faster drilling and requires around 50% less feed force than conventional HSS drills; this reduces operator fatigue and shortens cycle times in production environments. The combination of short overhang and a fully ground flute results in improved runout accuracy, especially when used in a stable drilling set-up such as a drilling machine. Durable coating and optimised geometry for longer tool life A TIN-coated surface significantly lowers friction and helps to reduce wear when machining alloyed and unalloyed steels, cast materials and non-ferrous metals. With appropriate cooling, the Titanium Nitride layer increases service life and keeps cutting edges sharper for longer, so fewer tool changes are needed. The 118° point angle eases centring on slightly curved or coated surfaces and balances entry aggressiveness with edge strength, which is beneficial when drilling materials like aluminium, copper and hard plastics. Engineered for metal: materials and standards explained Conformity to DIN 338 indicates this tool is a short twist drill with a cylindrical shank manufactured from HSS and produced either by grinding or rolling; the MetavCUT version is ground, which provides very sharp cutting edges and high concentricity. Ground drills excel in metalworking because the flute geometry and primary cutting edges are precise, producing accurate hole dimensions and improved surface finish. Note: ground HSS drills can be more brittle than rolled types and perform best with steady clamping and adequate cooling. Practical use cases and operator guidance This Twist Drill is intended primarily for drilling metal on stationary or portable drilling machines and is suitable for machinists, toolrooms and maintenance shops requiring reproducible, high-quality holes. For best results use moderate spindle speeds, apply a suitable coolant for steels and clamp the workpiece securely. The fully ground shank eases chuck gripping and reduces slippage. If uncertain whether this drill meets specific requirements or if additional technical data is needed, METAV Werkzeuge offers expert support and consultation to help select the correct tool and machining parameters. We recommend the MetavCUT short Twist Drill for precision metalworking — for personalised advice contact METAV Werkzeuge by email info@metav-werkzeuge.com or phone +49 2822 7131930 (WhatsApp +49 170 2837271) Technical Specifications Designation: Twist Drill Marke: MetavCUT SKU: 28080-FDA Diameter: 8 mm Point angle: 118° Type / Execution: short Coating / Colour: TIN-coated Spiral length: 75 mm Overall length: 117 mm Shank execution: fully ground Material: HSS-G Standard: DIN 338 Application: Drills for metal For drilling machine: drilling machine Manufacturer: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What are Twist Drills used for? The MetavCUT Twist Drill is mainly applied to the machining of high-strength materials and larger diameters; its shape is easy to regrind and it withstands significant loads, making it especially suitable for metalworking and demanding applications. Which three drill types exist? Drill types are commonly categorised as metal drills, wood drills and stone/concrete drills, with the MetavCUT Twist Drill belonging to the metal drill category and optimised for that purpose. Is there anything else you need to determine whether this tool suits your process? Are additional dimensions or speed recommendations required? METAV Werkzeuge provides comprehensive and competent advice — feel free to contact us by email at info@metav-werkzeuge.com, by phone at +49 2822 7131930 or via WhatsApp at +49 170 2837271
8mm HSS-G Twist Drill DIN 338 ,short, TIN-coated, Type N - MetavCUT
Die Kombination aus HSS-G Material, TiN-Beschichtung und kurzer Ausführung sorgt für präzise Bohrungen und höhere Standzeit bei Metallbearbeitung. Nutzen Sie die erhöhte Stabilität und die optimierte Schneidgeometrie zur Effizienzsteigerung in der Werkstatt. Bestellen Sie den Spiralbohrer direkt über Metav Werkzeuge oder fragen Sie unsere Beratung bei Bedarf an. Spiralbohrer von MetavCUT – kurze Ausführung für Metall Spiralbohrer von MetavCUT in kurzer Ausführung eignet sich für präzise Bohrungen in legierten und unlegierten Stahl sowie Guss- und Nichteisenmetallen Spiralbohrer Typ N für Metallbearbeitung HSS-G geschliffen für präzise Bohrungen TiN-Beschichtung reduziert Verschleiß Kurze Ausführung für hohe Stabilität Geeignet für Handbohrmaschine und Werkstatt Robuste Beschichtung und Material für längere Standzeit Aufgrund des HSS-G Werkstoffs in Kombination mit der TiN-Beschichtung wird die Reibung beim Bohren reduziert und die Lebensdauer des Werkzeugs erhöht. Diese Eigenschaft führt zu weniger Werkzeugwechseln und damit zu besserer Auslastung der Maschine und geringeren Betriebskosten. Anwender profitieren insbesondere bei häufigen Bohrzyklen in Stahl und Guss durch gleichbleibende Bohrbildqualität und reduzierte Nacharbeit. Kurze Ausführung für höhere Präzision und Stabilität Die kürzere Gesamtlänge reduziert die Auskraglänge und damit das Risiko von Schwingungen und Durchbiegung während des Bohrens. In Kombination mit der geschliffenen Fertigung nach DIN 338 ergibt sich eine hohe Rundlaufgenauigkeit, die saubere Bohrlöcher ermöglicht. Der 135° Spitzenwinkel unterstützt das Anbohren harter Werkstoffe und verringert das Ausreißen bei Ein- und Austritt. Effiziente Bohrleistung und geringerer Kraftaufwand Durch die geschliffene Geometrie lässt sich das Material schneller schneiden; das Werkzeug ermöglicht laut Herstellerangaben bis zu 40% schnelleres Bohren bei gleichzeitig bis zu 50% weniger Anpresskraft. Das resultiert in kürzeren Durchlaufzeiten und weniger Ermüdung für Bediener. Diese Effizienz zahlt sich bei Serienarbeiten und Instandsetzungen aus, wenn Präzision und Produktionsgeschwindigkeit gefragt sind. Vielseitiger Einsatz und Anwenderempfehlung Für Werkstätten, Montagebetriebe und Handwerk ist diese kurze Ausführung ideal geeignet, wenn stationäre oder handgeführte Maschinen zum Einsatz kommen. Der Bohrer ist besonders für den Standard-Bereich mit 2 mm bis 13 mm Durchmesser ausgelegt und deckt typische Metallarbeiten zuverlässig ab. Anwender mit Bedarf an hoher Präzision und Stabilität erhalten mit diesem Werkzeug eine praxisgerechte Lösung für vielfältige Metallanwendungen. Wählen Sie den MetavCUT Spiralbohrer aus der Standard Line für zuverlässige Metallbohrungen und kontaktieren Sie bei technischen Fragen unser Team per eMail info@metav-werkzeuge.com oder Telefon +49 2822 7131930 für persönliche Beratung Produktmerkmale Artikelnummer: 46080-FDA Hersteller: MetavCUT Bezeichnung: Spiralbohrer Serie: Standard Line Norm: DIN 338 Material: HSS-G Farbe: TIN-beschichtet Ausführung: kurz Schaftausführung: geschliffen Typ: Typ N Für Bohrmaschine: Handbohrmaschine Verpackungseinheit: 5 Fakten Durchmesser: 8 mm Gesamtlänge: 117 mm Spirallänge: 75 mm Spitzenwinkel: 135° Verpackungseinheit: 5 Besonderheiten Material: HSS-G (Schnellarbeitsstahl, geschliffen) Beschichtung: TIN-beschichtet (Titan-Nitrid, erhöhte Verschleißfestigkeit) Schaftausführung: geschliffen Norm: DIN 338 (kurze Spiralbohrer mit Zylinderschaft) Typ: Typ N (Normalspirale für Metall) Hersteller: MetavCUT Modellserie: Standard Line Ausführung: kurz Für Bohrmaschine: Handbohrmaschine FAQ Für welche Materialien eignet sich der Bohrer am besten? Der MetavCUT Spiralbohrer Standard Line (SKU 46080-FDA) ist ausgelegt für legierten und unlegierten Stahl, Gusseisen, Temperguss, Sintereisen sowie Nichteisenmetalle wie Kupfer und Bronze und eignet sich ebenfalls für Hartkunststoff. Kann der Bohrer mit einer Handbohrmaschine verwendet werden? Ja, die kurze Ausführung und die Zylinderschaft machen den MetavCUT Spiralbohrer Standard Line geeignet für den Einsatz in Handbohrmaschine und stationären Maschinen, sofern auf Rundlauf und geeignete Spannaufnahme geachtet wird. Welche Vorteile bringt die TiN-Beschichtung in der Praxis? Die TiN-Beschichtung des MetavCUT Spiralbohrers reduziert Reibung und Verschleiß, was die Standzeit erhöht und die Wärmeentwicklung beim Bohren verringert; das führt zu gleichmäßigeren Bohrungen und weniger Werkzeugwechseln. Welche Bohrparameter werden empfohlen für 8 mm in gehärtetem Stahl? Für den MetavCUT Spiralbohrer mit 8 mm Durchmesser und 135° Spitzenwinkel empfiehlt sich reduzierte Schnittgeschwindigkeit und ausreichende Kühlmittelzufuhr; bei Unsicherheit die Herstellerangaben und Maschinenleistung prüfen. Wie beeinflusst die geschliffene Ausführung die Bohrqualität? Die geschliffene Geometrie des MetavCUT Spiralbohrers (HSS-G) sorgt für scharfe Schneiden und hohe Rundlaufgenauigkeit, was saubere Bohrlöcher und geringere Nacharbeit in der Metallbearbeitung ermöglicht.
8mm HSS-G Twist Drill DIN 338 ,short, TIN-coated, Type N - MetavCUT
Die Kombination aus kurzer Ausführung, TIN-beschichtetem HSS-G und dem 135° Spitzenwinkel sorgt für hohe Stabilität, präzise Bohrlöcher und verlängerte Standzeit bei der Bearbeitung harter Werkstoffe. Nutzen Sie die robuste Profi Line Ausführung für präzise Metallbearbeitung und kontaktieren Sie Metav bei Fragen zur Anwendung oder Bestellung. Spiralbohrer – MetavCUT Profi Line HSS-G, kurz Der Spiralbohrer der Profi Line ist ein kurzer, geschliffener HSS-G-Bohrer mit TIN-Beschichtung für präzises Bohren in legierten und unlegierten Stählen sowie Nichteisenmetallen kurze Ausführung für höhere Stabilität HSS-G geschliffen für präzise Bohrlöcher TIN-Beschichtung reduziert Verschleiß deutlich 135° Spitzenwinkel für harte Werkstoffe Geeignet für Handbohrmaschine und stationäre Maschinen Mehr Präzision bei harten Werkstoffen dank kurzer Ausführung Durch die kurze Auskraglänge reduziert sich die Neigung zum Verbiegen, wodurch die Bohrung genaueren Rundlauf und bessere Passgenauigkeit liefert. Diese Bauart ist besonders vorteilhaft beim Bohren in legierten und unlegierten Stahl, Gusseisen und Temperguss, weil die Kraftübertragung direkter erfolgt und die Führung verbessert wird. Der geschliffene Schaft trägt zur hohen Rundlaufgenauigkeit bei. Für Anwender bedeutet das weniger Nacharbeit und konstante Qualität bei Serien oder Einzelteilen. Längere Standzeit durch Beschichtung und geschliffene Geometrie Die TIN-Beschichtung (Titan-Nitrid) verringert die Reibung und schützt den Bohrer gegen thermischen Verschleiß, insbesondere bei höheren Schnittgeschwindigkeiten und bei Einsatz von Kühlschmierstoff. In Verbindung mit dem HSS-G CNC-Schliff entstehen scharfe Schneidkanten, die saubere Bohrungsränder liefern und das Spanverhalten verbessern. Anwender profitieren von längeren Werkzeugstandzeiten und gleichbleibender Bohrqualität, was Stillstandzeiten und Werkzeugwechsel reduziert. Geeignete Anwendungen und empfohlene Einsatzweise Diese kurze Ausführung ist ausgelegt für den Einsatz an Handbohrmaschinen sowie an stationären Maschinen für präzise Metallbearbeitung. Ideal ist die Verwendung bei der Bearbeitung von Stahl, Edelstahl, Kupfer, Bronze, Neusilber und Hartkunststoffen. Vorbohren für größere Durchmesser und Kühlung bei langen Einsätzen erhöhen die Wirtschaftlichkeit. Die Norm DIN 338 klassifiziert diese Bauform und erleichtert die Auswahl kompatibler Bohrer für die Werkstatt. Handhabung, Spitzenwinkel und Sicherheitshinweise Der 135° Spitzenwinkel reduziert das Anbohren bei harten Werkstoffen und verlängert die Lebensdauer bei Anwendungen mit hohem Druck. Der geschliffene Typ N Normalspirale bietet ein ausgewogenes Verhältnis aus Schneidführung und Spanabfuhr. Beim Gebrauch sollten Drehzahl, Vorschub und Kühlschmierstoff an Material und Bohrergröße angepasst werden, um Bruchgefahr zu minimieren. Für handgeführte Anwendungen empfiehlt sich eine stabile Aufspannung und kontrollierte Vorschubkraft. Empfehlung: Setzen Sie auf die MetavCUT Profi Line mit TIN-Beschichtung für langlebige Präzision. Für technische Beratung oder Bestellung erreichen Sie Metav per E‑Mail: info@metav-werkzeuge.com oder Telefon: +49 2822 7131930. Technische Daten Artikelnummer: 41080-FDA Marke: MetavCUT Serie / Baureihe / Ausführung: Profi Line SKU: 41080-FDA Fakten Durchmesser: 8 mm Gesamtlänge: 117 mm Spirallänge: 75 mm Spitzenwinkel: 135° Verpackungseinheit: 5 Besonderheiten Material: HSS-G (geschliffen) – geschliffener CNC-Schliff für hohe Rundlaufgenauigkeit Farbe: TIN-beschichtet – Titan-Nitrid-Beschichtung für geringeren Verschleiß Norm: DIN 338 – kurze Spiralbohrer mit Zylinderschaft Schaftausführung: geschliffen Typ: Typ N – Normalspirale Anwendung: Bohrer für Metall Für Bohrmaschine: Handbohrmaschine FAQ Was unterscheidet den kurzen HSS-G-Bohrer von einem Standardbohrer? Die kurze Ausführung der MetavCUT Profi Line reduziert die Auskraglänge und erhöht dadurch die Stabilität. In Kombination mit dem geschliffenen HSS-G liefert der Bohrer präzisere Bohrungen und besseren Rundlauf als Standardlangbohrer. Für welche Materialien ist dieser Spiralbohrer geeignet? Der Spiralbohrer von MetavCUT eignet sich für legierten und unlegierten Stahl, Gusseisen, Temperguss, Sintereisen, Neusilber, Kupfer, Bronze und Hartkunststoffe dank der robusten Geometrie und der TIN-Beschichtung. Wie wirkt sich der 135° Spitzenwinkel auf die Bohrleistung aus? Ein Spitzenwinkel von 135° sorgt für besseren Anbohrkomfort in harten Werkstoffen und reduziert das Ausbrechen. Dadurch wird die Lebensdauer des Werkzeugs erhöht und die Bohrqualität verbessert. Ist der Bohrer für handgeführte Maschinen geeignet? Ja, die kurze Ausführung ist für Handbohrmaschine und stationäre Maschinen geeignet. Bei handgeführten Einsätzen ist auf gleichmäßigen Vorschub und sichere Aufspannung zu achten. Welche Vorteile bietet die TIN-Beschichtung konkret? Die TIN-Beschichtung der MetavCUT Profi Line reduziert Reibung und thermischen Verschleiß, was zu längeren Standzeiten führt und die Wartungsintervalle verlängert.
8mm HSS-G Twist Drill DIN 338 - MetavCUT
Twist Drill Spezial – 8 mm, 135° point, HSS‑G, DIN 338, with multi‑bevel cutting edge and triangular shank (MetavCUT) The Twist Drill Spezial is a precision metal drilling tool designed for drilling machines and cordless drills, optimised for hard and alloyed steels as well as a wide range of metals. High‑performance HSS‑G for durable drilling 135° point for clean starts in hard materials Triangular shank ensures secure grip in chucks Conforms to DIN 338 for standardised short twist drills Faster, more efficient metalworking for demanding tasks The specially ground HSS‑G geometry of this tool delivers up to 40% faster drilling and requires around 50% less feed force compared with conventional HSS drills, which directly reduces operator fatigue and cycle times. This performance advantage means fewer tool changes and higher throughput in workshop environments. For fabrication and production settings where speed and repeatability matter, the reduced thrust requirement also lowers the load on cordless and stationary machines, extending battery life and reducing wear on the machine spindle. Durable material and tip design for precise, burr‑free holes Made from HSS‑G, the drill combines toughness and heat resistance to resist softening at elevated cutting temperatures; this yields longer tool life on steel and cast materials. The 135° point angle is tailored for harder workpieces and reduces walking at the start of a hole, delivering clean, burr‑free edges. The specially sharpened tip also improves centring and helps to maintain roundness of the drilled hole, which is particularly beneficial when tolerance and surface quality are critical. Wide application range and machine compatibility This Twist Drill Spezial is intended primarily for metalworking and is suitable for alloyed and unalloyed steels, cast steels, cast irons, sintered irons, non‑ferrous metals, hard plastics and even wood where a metal drill is acceptable. The triangular shank offers reliable torque transmission and is especially practical for use with cordless drills and portable machines, while compatibility with stationary drilling machines supports workshop and production use. Users who need a versatile metal drill will appreciate the balance between cutting speed and hole quality. Standards, handling and recommended use for safe results Manufactured to DIN 338, the product meets the standard definition for short twist drills with cylindrical shank, aiding selection and interchangeability. For best results use appropriate cutting fluids when drilling steels and consider slower spindle speeds for larger diameters or harder materials. The 75 mm spiral length and 117 mm overall length are optimised for through‑holes and common workshop applications; the 135° point angle shortens the initial penetration time in harder materials and improves centring during the pilot phase. MetavCUT recommends the Twist Drill Spezial for precision metal drilling — for technical advice and application support contact METAV Werkzeuge at info@metav-werkzeuge.com or by phone +49 2822 7131930, WhatsApp +49 170 2837271 Precise Technical Data for Planning and Setup Designation: Twist Drill Spezial 8 mm Brand: MetavCUT SKU: 55080-FDA Type/Series: Spezial Diameter: 8 mm Spiral Length: 75 mm Overall Length: 117 mm Point Angle: 135° Material: HSS‑G Shaft Execution: with multi‑bevel cutting edge and triangular shank Application: Drills for metal For drilling machine: Drilling Machine (Handbohrmaschine) Norm: DIN 338 Manufacturer: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What are Twist Drills used for? The MetavCUT Twist Drill Spezial is mainly used for the machining of high‑strength workpieces and larger drill diameters; it is particularly suitable for alloyed and unalloyed steel, cast materials and non‑ferrous metals. The design allows easier regrinding and maintains performance under higher loads. Which 3 drill types are there? The three common drill types are metal drills, wood drills and stone/concrete drills; the MetavCUT Twist Drill Spezial belongs to the metal drill category and is optimised for metalworking tasks. Are you unsure whether this tool meets your requirements or need additional technical data? METAV Werkzeuge provides comprehensive, competent advice for complex or high‑precision tools — contact us by email at info@metav-werkzeuge.com, by phone at +49 2822 7131930 or via WhatsApp at +49 170 2837271.
8mm HSS-G Twist Drill DIN 340 ,long, bright finished - MetavCUT
Twist Drill — Long HSS‑G 8 mm, 135° Point, DIN 340, Bright Finished Drill Bit A Twist Drill by MetavCUT is a long HSS‑G 8 mm drill bit for drilling machines, engineered for deep, precise metal bores. Long version for deeper and hard‑to‑reach bores Fully ground shaft for high concentricity and clean holes 135° point angle optimised for harder materials Conforms to DIN 340 for consistent overall length and quality Bright finished surface for corrosion resistance and easy chip evacuation High‑performance geometry for efficient metal drilling The long HSS‑G design combines extended reach with a ground spiral that provides faster penetration and reduced required feed force compared with rolled bits. This construction is particularly advantageous when working with alloyed and unalloyed steels, cast materials and hard plastics: the fully ground flute geometry yields sharp cutting edges and excellent runout accuracy. For users who need deeper bores or access to recessed holes, the extended overall length ensures reach without compromising hole quality. Cleaner holes and better centring on tough workpieces A 135° point angle reduces walking and improves centring when entering tough materials such as stainless steel. The reduced chisel edge from the point geometry lowers friction and allows for smoother entry, meaning less burr formation and cleaner bores. When paired with appropriate coolant and moderate speeds, the bit delivers precise, repeatable results that decrease post‑processing and rework. Built for workshops and drilling machines This Twist Drill is intended for use with standard drilling machines and is specified to DIN 340, which defines the longer execution for deep drilling tasks. The bright finished surface improves chip flow and offers basic corrosion protection during storage and operation. Its characteristics make it suitable for professional machinists and maintenance workshops that require a reliable, stable standard drill for a broad range of metalworking applications. Recommendations for use and tool care To maximise tool life and performance, use coolant when machining harder alloys and observe recommended cutting speeds for HSS‑G material. Because fully ground HSS bits can be more brittle than rolled variants, avoid shock loading and prefer stationary machines or well‑supported power drills. Regular sharpening restores cutting geometry; ground bits are straightforward to regrind to maintain the original precision and cutting behaviour. For deep, precise metal drilling choose the MetavCUT Twist Drill long HSS‑G 8 mm — METAV Werkzeuge offers expert technical advice and personalised support at info@metav-werkzeuge.com or by phone at +49 2822 7131930, WhatsApp +49 170 2837271 Technical Data Bezeichnung: Twist Drill Marke: MetavCUT SKU: 53080-FDA Diameter: 8 mm Gesamtlänge: 165 mm Spirallänge: 109 mm Spitzenwinkel: 135° Material: HSS-G Ausführung: long Schaft Ausführung: fully ground Für Bohrmaschine: Drilling Machine Farbe: bright finished Norm: DIN 340 Modellserie: Standard Line Anwendungen: Drills for metal Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What is a Twist Drill used for? The MetavCUT Twist Drill is mainly used for drilling in metal; it is especially suited for machining high‑strength materials and larger diameters where deeper or recessed bores are required. Its ground geometry allows precise holes and reliable centring even in demanding workpieces. Which three drill types are there? The main categories are metal drills, wood drills and stone/concrete drills. The MetavCUT Twist Drill belongs to the metal drill group and is optimised for that application. Why are twist drills sharpened at the tip? The tip sharpening reduces the chisel edge at the drill point, which significantly lowers friction and required feed force. As a result the MetavCUT Twist Drill centres better in the workpiece and cuts with less resistance. Can a metal twist drill be used to drill wood? A metal drill such as the MetavCUT Twist Drill can be used in wood, but guidance and finish are inferior compared with dedicated wood drills. Metal bits are easier to resharpen and typically exhibit less self‑feeding action than wood‑specific designs. At what drilling depths is the twist drill most commonly used? A twist drill is the standard tool for through‑hole drilling in solid material. For diameters up to around 20 mm and depths up to approximately 100 mm, the twist drill is the most frequently used tool; the long version of the MetavCUT Twist Drill extends this capability for deeper holes.
8mm NC Spot Drill HSS-Co 120° With Cylindrical Shank DIN 1835-A, Right-Hand Cutting - TECWERK
Take advantage of the HSS‑Co construction, the 120° point geometry and the DIN 1835‑A cylindrical shank for precise, repeatable centring and chamfering in a single operation; order directly via Metav Werkzeuge or consult our specialists for application guidance. NC spot drill, 8 mm — HSS‑Co, 120° tip, TECWERK NC spot drill, 8 mm — HSS‑Co, 120° tip, TECWERK is designed for fast, position‑accurate spot drilling and combined centring/countersinking on CNC machines and drilling centres. HSS‑Co for improved wear resistance Cylindrical shank to DIN 1835‑A 120° tip for accurate centring Right‑hand cutting for conventional machining Faster first‑operation centring and chamfering The combination of a 120° point and a robust HSS‑Co grade enables the tool to centre and chamfer threaded hole starts in one pass, reducing setup time and cycle complexity. This saves operation steps on CNC machining centres by eliminating a separate countersinking stage; the result is a more efficient process and fewer tool changes. The geometry supports stable chip formation and improves positional accuracy when preparing holes for subsequent tapping. Consistent performance on automated equipment With a DIN 1835‑A cylindrical shank the tool seats reliably in standard tool holders, providing repeatable concentricity during high‑speed indexing and automatic tool changes. The right‑hand cutting orientation and the specified feed behaviour — 0.07 mm/rev at workpiece contact up to 800 N — allow predictable material removal in steel, helping planners calculate feeds and cycle times with confidence. This makes the cutter suitable for serial production where process stability is essential. Practical benefits for workshop and production planners As a purpose‑built NC spot drill the design minimises runout and reduces the risk of false starts or eccentric entry marks. The 8 mm nominal diameter and compact point ensure clean centring even on small holes, supporting tight tolerance requirements and a neat finish before tapping. For procurement teams, the robust HSS‑Co composition means longer tool life under intermittent manufacturing loads, improving overall cost per hole. Application recommendations and machining notes Intended for use on CNC machines and drilling centres, the tool is right‑hand cutting and best applied with steady feed as specified. The integrated centring and chamfer function is particularly advantageous for tapped holes where precise alignment and a smooth lead‑in are required. Where softer alloys are processed, standard parameters may be reduced; in tougher steels adhere to the stated feed guidance to maintain geometry and avoid premature wear. Contact Metav Werkzeuge for tailored application support or to reserve the TECWERK NC spot drill with DIN 1835‑A shank for reliable production use — Metav Werkzeuge is ready to advise from Emmerich. Technical data Article number: 2000860088NW Manufacturer: TECWERK Packaging unit: 1 Facts Diameter: 8 mm Point angle: 120° Feed in steel up to 800 N: 0.07 mm/rev Shank standard: DIN 1835‑A Special features Material: HSS‑Co Cutting direction: right‑hand cutting Application: position‑accurate spot drilling on NC machines and drilling centres Function: centring and chamfering of threaded hole starts in one pass FAQ What is the primary application for this tool? The TECWERK NC spot drill is intended for position‑accurate spot drilling and simultaneous centring and chamfering of threaded hole starts on CNC machines and drilling centres. Which shank standard does the tool use and why does that matter? The tool features a DIN 1835‑A cylindrical shank, which ensures reliable seating in standard holders and consistent concentricity during automatic tool changes and high‑speed operation. What material is the drill made from and what benefit does it provide? Made from HSS‑Co, the drill offers improved wear resistance and endurance under production loading, extending service life compared with unalloyed high‑speed steels. Is there guidance for feeds when machining steel? Yes — at workpiece contact up to 800 N the recommended feed is 0.07 mm/rev, which supports predictable chip formation and process stability in steel. Manufacturer/Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund
8mm NC Spot Drill HSS-Co TiN 90° Cylindrical Shank DIN 1835-A, Right-Hand - TECWERK
Take advantage of the combination of HSS‑Co core, TiN coating and a 90° point for fast, position‑accurate spot drilling and simultaneous centring and chamfering; order the tool directly via Metav Werkzeuge or consult the application specialists for tailored guidance. NC spot drill 8 mm – HSS‑Co, TiN, 90° | TECWERK NC spot drill 8 mm for precise positional spot drilling, centring and chamfering on NC machines and drilling rigs Cobalt HSS (HSS‑Co) for lasting durability TiN coating for reduced wear and longer life 90° point for accurate centring and chamfering DIN 1835‑A cylindrical shank for secure clamping Faster cycle times through combined centring and chamfering The tool is designed to perform centring and chamfering in a single operation, reducing set‑up time and the number of tool changes required on NC equipment. The 90° point produces a clear centring mark and a consistent chamfer for threaded holes, which simplifies subsequent tapping and improves thread start. For production environments where repeatability and short cycle times matter, the integrated function of this spot drill helps maintain a smooth workflow and fewer reworks. Durable performance under high thermal load Constructed from HSS‑Co (cobalt high‑speed steel) and finished with a TiN coating, the centre tool offers enhanced heat resistance and lower friction at the cutting edge. The cobalt alloy increases hot‑hardness, while the titanium nitride layer reduces abrasive wear, resulting in extended tool life and stable cutting geometry during serial operations. These material choices are particularly advantageous when processing steel components at elevated speeds. Machine compatibility and secure clamping for precise results The DIN 1835‑A cylindrical shank ensures compatibility with standard collets and holders used on NC machines and drill rigs, providing secure clamping and minimised run‑out. The right‑hand cutting geometry is optimised for conventional spindle rotation. The specified reference feed in steel — 0.07 mm/rev at cutting forces up to 800 N — offers an initial guideline for setting feeds; actual values should be adjusted to machine rigidity and workpiece conditions to achieve consistent hole quality. Practical advantages on the shop floor As a purpose‑built spot drill, this tool reduces burr formation at hole entry and creates a reliable locating feature for subsequent operations, which supports higher first‑pass yields. The robust construction and coating mean fewer tool changes and lower production downtime. Supplied with a standard cylindrical shank, the component is easy to integrate into existing tool sets and replacement routines, helping to keep machine uptime high and maintenance predictable. Request application advice from Metav Werkzeuge to specify the TECWERK NC spot drill for the intended operation; the Emmerich team provides reliable supply and practical machining guidance Technical data Article number: 2000861388NW Manufacturer: TECWERK Packaging unit: 1 Facts Diameter: 8 mm Point angle: 90° Feed in steel up to 800 N: 0.07 mm/rev Special features Material: HSS‑Co (cobalt high‑speed steel) Coating: TiN (titanium nitride) Shank: cylindrical, DIN 1835‑A Cutting direction: right‑hand cutting Application: positional spot drilling, centring and chamfering on NC machines and drill rigs FAQ Is this spot drill suitable for preparing threaded holes? Yes. The TECWERK NC spot drill 8 mm is designed to centre and chamfer threaded holes in one pass, producing a clear lead‑in that eases tapping and reduces thread start problems. What shank standard does the tool use and which holders are compatible? The tool is supplied with a cylindrical shank to DIN 1835‑A, making it compatible with standard collets and holders commonly used on NC machines and drilling rigs. Which materials can be drilled with this tool? The tool is intended primarily for steel applications; the HSS‑Co substrate and TiN coating are optimised for robust performance when machining steel workpieces under normal production feeds. How should the feed be set for steel components? Use the indicated reference of 0.07 mm/rev in steel (up to 800 N) as a starting point and adapt feed and speed to machine rigidity, clamping and workpiece condition for optimal hole quality. Does the TiN coating require special handling or reconditioning? The TiN coating reduces wear and friction during use; no special handling is required, though correct clamping and avoidance of excessive axial shock will prolong service life. Manufacturer/Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund
8mm Rollgewalzter HSS Spiralbohrer, 118° Spitzenwinkel, Morsekegel, Schwarz - MetavCUT
Der Spiralbohrer von MetavCUT kombiniert rollgewalzte Fertigung, HSS-Material und Morsekegel-Schaft zu einem robusten Werkzeug für Standard-Metallbohrungen; profitieren Sie von hoher Zähigkeit, guter Standzeit und sicherer Spannübertragung direkt über Metav Werkzeuge oder lassen Sie sich von unserer Beratung unterstützen. Spiralbohrer von MetavCUT Standard Line (Morsekegel) Der Spiralbohrer ist ein rollgewalztes HSS-Spiralwerkzeug für robuste Metallbohrungen mit Morsekegel-Schaft, geeignet für allgemeine Werkstatt- und Maschinenanwendungen. HSS-Spiralbohrer, rollgewalzte Bauart Morsekegel-Schaft für hohe Drehmomentübertragung Ø 8 mm, Spirallänge 87 mm, Gesamtlänge 168 mm Für Stahl bis ca. 900 N/mm² geeignet Spitzenwinkel 118° für leichte Zentrierung Zähigkeit durch Fertigungsverfahren und Material für wirtschaftliche Bohrungen Die Kombination aus HSS und der rollgewalzten Herstellung macht dieses Spiralwerkzeug besonders zäh und bruchsicher. Weil der Rundstab beim Walzen in die Spirale gepresst wird, entsteht eine erhöhte Elastizität, die gerade bei kleineren Durchmessern das Bruchrisiko reduziert. Für Anwender bedeutet das weniger Werkzeugwechsel und geringere Stillstandszeiten bei Serien- und Einzelaufträgen. Geeignete Einsatzfelder und klare Materialgrenzen für sichere Planung Für alle üblichen Metallarbeiten in Werkstatt und Betrieb ist dieses Spiralwerkzeug ausgelegt: legierter und unlegierter Stahl, Gusswerkstoffe sowie Nichteisenmetalle und Kunststoffe. Die Angabe zur Festigkeit von ca. 900 N/mm² dient als Planungsgröße, damit Bohrungen in passenden Werkstoffen zuverlässig und wirtschaftlich ausgeführt werden können. So lassen sich Aufträge schneller kalkulieren und umsetzen. Maschinenanforderungen und Anwendungshinweise für präzise Ergebnisse Bei stationären Maschinen mit Morsekegel-Aufnahme sitzt der Bohrer sehr fest und überträgt hohe Lasten ohne zusätzliches Bohrfutter. Der Morsekegel sorgt für Selbsthemmung und Genauigkeit, vor allem bei höheren Vorschüben. Bei handgeführten Geräten empfiehlt sich vorbohren oder der Einsatz von Zentrierhilfen, um Wanderneigung zu vermeiden und saubere Bohrbilder zu erzielen. Praktische Tipps zur Handhabung und Lebensdauersteigerung Ein Spitzenwinkel von 118° erleichtert das Anstechen in weichere Materialien und verbessert das Zentrieren auf gewölbten Flächen. Für tiefe Bohrungen ist auf ausreichende Spanabfuhr und gegebenenfalls Kühlung zu achten, damit sich die Standzeit verlängert. Durch regelmäßiges Nachschleifen der Schaft- und Schneidengeometrie kann die Nutzungsdauer weiter optimiert werden. Die Empfehlung: MetavCUT Standard Line Spiralbohrer mit Morsekegel wählen für zuverlässige Metallbohrungen; bei Bedarf technische Rückfragen an info@metav-werkzeuge.com oder Telefon +49 2822 7131930 richten Technische Daten Artikelnummer: 54080-FDA Marke: MetavCUT Serie: Standard Line Bezeichnung: Spiralbohrer Norm: DIN 345 Anwendung: Bohrer für Metall Fakten Durchmesser: 8 mm Gesamtlänge: 168 mm Spirallänge: 87 mm Spitzenwinkel: 118° Besonderheiten Material: HSS Ausführung: rollgewalzt Schaftausführung: Morsekegel (MK) – konische Aufnahme, selbsthemmend Farbe: schwarz Verpackungseinheit: 1 Label: Spiralbohrer SKU: 54080-FDA FAQ Welche Materialien lassen sich mit dem Spiralbohrer bearbeiten? Der MetavCUT Standard Line Spiralbohrer eignet sich zum Bohren von legiertem und unlegiertem Stahl, Gusswerkstoffen, Nichteisenmetallen und Kunststoffen; die Angabe bis ca. 900 N/mm² dient als Richtwert für die Planung. Ist der Schaft für Ständerbohrmaschinen geeignet? Ja, der Spiralbohrer verfügt über einen Morsekegel-Schaft, sodass er direkt in passende Morsekegel-Aufnahmen von Ständerbohrmaschine oder Drehmaschine eingesetzt werden kann. Wie beeinflusst die rollgewalzte Fertigung die Leistung? Die rollgewalzte Bauart verleiht dem HSS-Material höhere Zähigkeit und geringeres Bruchrisiko, was besonders bei Standardaufgaben in Werkstatt und Montage wirtschaftliche Vorteile bringt. Welcher Spitzenwinkel ist optimal für unterschiedliche Werkstoffe? Der Spiralbohrer hat einen Spitzenwinkel von 118°, der sich besonders für weichere Materialien und einfache Zentrierung eignet; härtere Werkstoffe können andere Winkel benötigen. Gibt es eine Teilenummer zur Bestellung oder Rückfrage? Für Bestellungen und technische Rückfragen nutzen Sie bitte die Artikelnummer 54080-FDA für den MetavCUT Standard Line Spiralbohrer.
8mm Solid Carbide Spot Drill 90° For High-Strength Steel And Castings, Cylindrical Shank DIN 6535-HA - TECWERK
Benefit from the combination of solid carbide construction, a 90° point for reliable centring and a DIN 6535‑HA cylindrical shank for secure clamping; order the NC centre drill directly via Metav Werkzeuge or consult our advisors for tailored machining guidance. NC centre drill D.8 mm, 90° – Solid carbide (TECWERK) NC centre drill D.8 mm, 90° – Solid carbide tool for precise centring and chamfering in one pass on NC machines Solid carbide 90° tip for accurate centring Cylindrical shank DIN 6535‑HA, secure clamping Right-hand cutting for standard machining operations Suitable for high-strength steels and non-ferrous metals Faster, more reliable centring and chamfering The combination of a 90° point and solid carbide construction ensures consistent initial guidance and immediate engagement when positioning on the workpiece. This design reduces tool walking and minimises the need for rework, so cycle times are shortened and setup reliability is increased. Thanks to the DIN 6535‑HA cylindrical shank, the tool is held firmly in standard chucks and holders on CNC lathes and machining centres, which stabilises the cutting process and supports repeatable accuracy across series production. Designed for NC machines and multi‑operation efficiency Engineered for use on NC machines and drilling rigs, the tool combines centring and chamfering in a single operation, removing the need for separate spotting and countersinking passes. The right-hand cutting geometry enables straightforward integration into existing programmes and supports predictable chip flow. For workplaces aiming to increase throughput, this approach translates into fewer tool changes, lower setup complexity and a smoother production flow while preserving hole quality for subsequent threading operations. Proven material performance and machining parameter guidance Developed for demanding materials, the tool is suitable for high-strength steels, steel castings, grey cast iron, stainless steels and non-ferrous metals, offering versatility across mixed production runs. For guidance during programming, a recommended reference feed in steel under a thrust force up to 800 N is 0.1 mm/rev, which balances tool life and surface finish in typical conditions. The solid carbide substrate maintains edge stability at higher spindle speeds, supporting efficient machining without sacrificing accuracy. Choose TECWERK solid carbide centre drills for consistent, process‑stable centring and chamfering — order via Metav Werkzeuge or contact our technical advisors for application-specific recommendations. Technical Data Article number: 2000865805NW Label: NC centre drill D.8 mm 90° TECWERK Manufacturer: TECWERK Packaging unit: 1 Facts Diameter: 8 mm Point angle: 90° Feed in steel (≤800 N): 0.1 mm/rev Shank standard: DIN 6535‑HA Special features Solid carbide (VHM) Cylindrical shank to DIN 6535‑HA Right‑hand cutting Positions‑accurate and fast pilot drilling on NC machines and drilling rigs Centring and chamfering of threaded holes in a single pass Suitable for high‑strength steels, steel castings, grey cast iron, stainless steels and non‑ferrous metals FAQ What materials can the NC centre drill be used on? The NC centre drill D.8 mm 90° is suitable for high‑strength steels, steel castings, grey cast iron, stainless steels and non‑ferrous metals. Is the shank compatible with standard holders and chucks? Yes, the tool features a DIN 6535‑HA cylindrical shank, which is compatible with standard chucks and tool holders for secure clamping. Can this tool centre and chamfer in one operation? The geometry of the tool allows both centring and chamfering of threaded holes in a single pass, reducing the number of operations required. What cutting direction does the tool use? The tool is manufactured with a right‑hand cutting geometry suitable for standard machining programmes. What is the reference feed for steel applications? As a machining reference, a feed of 0.1 mm/rev in steel under a thrust force up to 800 N is suggested for balanced performance and tool life. Manufacturer/Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund
8mm Solid Carbide Spot Drill TiAlN Coated 90° For NC Machines - TECWERK
Take advantage of precise positioning and combined centring/chamfering in a single pass thanks to the solid carbide construction and TiAlN surface treatment; this reduces cycle times and extends tool life. Order the NC spot drill directly via Metav Werkzeuge or contact the consultants if additional information is required. NC spot drill D.8 mm — solid carbide, TiAlN, 90° | TECWERK The NC spot drill D.8 mm is a solid‑carbide centre‑spotting tool designed for position‑accurate spot drilling and chamfering on NC machines and drilling rigs Solid carbide with TiAlN coating 90° tip for precise centring and chamfering Cylindrical shank to DIN 6535‑HA Suited for high‑strength steels and stainless steel Reduce machining steps with precise centring and chamfering The combination of a 90° tip and a robust geometry enables accurate centring and simultaneous chamfering, so one operation replaces two. This saves set‑up and cycle time on CNC lathes and drilling centres, improving throughput in repetitive production tasks. The pointed design ensures reliable position accuracy even in pre‑drilled or blind holes, reducing rework and alignment time. Longer tool life from hard coating and carbide substrate A solid carbide substrate with TiAlN coating gives a hard, heat‑resistant surface that maintains cutting edges under elevated temperatures. For manufacturers working with demanding alloys, this means fewer tool changes and more consistent hole quality. The coating also lowers built‑up edge formation on stainless and alloyed steels, translating into measurable cost advantages across batch runs. Built for automated NC operation and straightforward mounting The cylindrical shank to DIN 6535‑HA provides a standardised interface for chucks and tool holders, ensuring repeatable concentricity when used in automatic tool changers. Right‑hand cutting geometry offers predictable chip flow and stable cutting forces. Together these features support reliable automation and steady production, with less need for frequent recalibration. Application range and recommended cutting data explained This centre spot drill is optimised for high‑strength steels, steel castings, grey cast iron, stainless steels and non‑ferrous metals, enabling versatile use across workshops. For steels with cutting resistance up to 800 N, a recommended feed of 0.1 mm/rev balances edge life and hole quality. The tool is particularly effective where precise lead‑in and a clean chamfer are required before tapping or further reaming. For fast supply and expert advice on TECWERK solid‑carbide tooling, contact Metav Werkzeuge — info@metav-werkzeuge.com or call +49 2822 7131930 for direct support from Emmerich and reliable delivery to the workshop. Technical data Article number: 2000865814NW Manufacturer: TECWERK Item name: NC spot drill D.8 mm VHM TiAlN 90° Packaging unit: 1 Facts Diameter: 8 mm Tip angle: 90° Recommended feed in steel (up to 800 N): 0.1 mm/rev Shank standard: DIN 6535‑HA Special features Solid carbide (VHM) TiAlN coating Cylindrical shank to DIN 6535‑HA Right‑hand cutting For centring and chamfering in one pass Suitable for high‑strength steels, steel castings, grey cast iron, stainless steels and non‑ferrous metals FAQ What material is the tool made from? The NC spot drill D.8 mm is manufactured from solid carbide (VHM) for high rigidity and wear resistance. Is the tool suitable for stainless steel? Yes, the TiAlN coating and carbide substrate make the tool well suited for stainless steel applications. Can the tool perform centring and chamfering in a single operation? Yes, the 90° tip geometry is designed for combined centring and chamfering in one pass. What shank standard does the tool use? The tool has a cylindrical shank to DIN 6535‑HA, ensuring compatibility with standard tool holders. What feed rate is recommended for use in steel? For steel with cutting resistance up to 800 N, a feed of 0.1 mm/rev is recommended for balanced performance. Manufacturer/Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund
8mm Solid Carbide Spot Drill TiAlN Coating 142° Point Angle, Cylindrical Shank DIN 6535-HB - TECWERK
Take advantage of solid carbide construction and a TiAlN coating to achieve fast, positionally accurate spot drilling and simultaneous centring and chamfering on NC machines; order directly via Metav Werkzeuge or consult our advisors for application-specific guidance. TECWERK NC spot drill Ø 8 mm — solid carbide, TiAlN-coated centre drill with 142° point angle The TECWERK NC spot drill Ø 8 mm is a centre-drilling tool designed for fast, positionally accurate spotting and chamfering on NC machines and drilling rigs, ideal for preparing threaded holes and locating twist drills. Solid carbide body TiAlN coating for extended tool life 142° split-point for precise centring DIN 6535‑HB cylindrical shank Faster, more reliable centring and one-pass chamfering The solid carbide construction combined with a 142° point angle enables exact initial positioning and clean countersinking in a single operation, reducing secondary set-up and cycle time. Designed for use on NC machines, the tool provides stable runout for repeatable hole starts and prepares the thread entry with a chamfer at the same pass. The integrated geometry is optimised for right-hand cutting and is suitable as a pre‑centre for solid carbide drills with a tip angle between 120° and 140°, ensuring consistent guidance for subsequent drilling steps. Durable coating and material suitability for demanding jobs A TiAlN-coated surface delivers improved thermal resistance and wear protection, which extends tool life under elevated cutting temperatures. This makes the tool particularly effective on high‑strength steels, steel castings, grey cast iron, stainless steels and non‑ferrous metals, while preserving cutting-edge geometry. The coating reduces adhesion and increases oxidation resistance so that fewer interruptions for tool changes are required and consistent hole quality is maintained across production runs. Machine integration, handling and machining guidance The DIN 6535‑HB cylindrical shank ensures compatibility with standard tool holders and simple changeover in automated setups. For stable feeds in steel up to 800 N, a recommended feed of 0.1 mm/rev is indicated, which balances tool life and hole quality in typical NC operations. The tool’s right‑hand cutting flutes and optimised point geometry lower thrust forces during entry, improving positional accuracy and reducing the risk of drill walk. For precise parameter selection and adaptation to specific machine dynamics, Metav Werkzeuge offers technical consultation to match cutting data to the production environment. For application advice or to procure the TECWERK NC spot drill, contact Metav Werkzeuge for tailored recommendations and ordering: info@metav-werkzeuge.com or +49 2822 7131930 Technical Data Article number: 2000865841NW Product name: NC spot drill Ø 8 mm VHM TiAlN 142° Manufacturer: TECWERK Facts Diameter: 8 mm Point angle: 142° Recommended feed in steel (≤800 N): 0.1 mm/rev Special features Solid carbide TiAlN coating Cylindrical shank to DIN 6535‑HB Right-hand cutting For centring and chamfering of threaded holes in one pass Suitable for high-strength steels, cast iron, grey cast iron, stainless steels and non-ferrous metals Centres solid carbide drills with tip angles of 120–140° FAQ What materials can be machined with this spot drill? The TECWERK NC spot drill is suitable for high‑strength steels, steel castings, grey cast iron, stainless steels and a range of non‑ferrous metals, benefitting from its TiAlN coating and solid carbide construction. Is the shank compatible with standard tool holders? Yes, the tool features a DIN 6535‑HB cylindrical shank, ensuring reliable fitment in common NC machine holders and straightforward changeover. Can this tool prepare holes for subsequent solid carbide drills? The spotting geometry is designed to centre VHM (solid carbide) drills with tip angles from 120° to 140°, improving guidance and reducing drill wander for accurate follow‑up drilling. What feed should be used for steel applications? A recommended feed of 0.1 mm/rev for steel up to approximately 800 N offers a balance between tool life and hole quality; adapt feeds to material grade and machine rigidity. Does the TiAlN coating affect suitability for stainless steel? Yes, TiAlN increases thermal resistance and reduces adhesion, which enhances performance when machining stainless steels and other heat‑sensitive alloys. Manufacturer/Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund
High-performance drill bits for demanding production
Drill bits designed for industrial manufacturing where precision, repeatability and tool life are decisive. Based on a spectrum from HSS and kobalt-alloyed hss-e for universal use to solid carbide drills for high-speed, high-precision serial production, this range covers applications from general engineering to automotive supplier work.
Why these drill bits are essential in the workshop and on the machining centre
Function and behaviour:
- primary use: creating accurate cylindrical holes
- typical machines: CNC machining centres, lathes and drill presses
- key design aspects: optimised chisel edge, defined point angles, flute geometry for reliable chip evacuation
Technical advantages and process benefits:
- reduced feed forces through optimised point geometry
- improved heat control with advanced coatings and, where specified, internal coolant supply
- extended tool life using solid carbide variants and multilayer coatings such as TiN / TiAlN
- process security on challenging materials thanks to tailored materials and geometries
Concrete benefits that boost productivity and quality
- predictable tool life and fewer tool changes, lowering machine downtime
- stable hole quality and consistent tolerances across long runs
- efficient chip control and thermal management for safe deep-hole and hardened-material drilling
- suitability across a wide material range, reducing the need for multiple specialised tools
Metav as a reliable partner for high-precision tooling
Metav combines decades of sector expertise with a broad, dependable offering from its Emmerich facility. With over 48,000 customers and more than 250,000 products, Metav positions its range of drill bits, twist drills and indexable drills as a practical, quality-first choice for procurement managers and production engineers seeking dependable supply and technical competence.
Technical data (at a glance)
- material: HSS, kobalt-alloyed hss-e, solid carbide
- coatings: TiN, TiAlN, advanced nanocoatings
- coolant option: internal coolant feed where specified
- typical applications: mild steel, high-alloy stainless steel, cast iron, non-ferrous metals, technical plastics, hardened materials (use solid carbide variants)
- tool types available: twist drills, solid carbide drills, indexable drills, centre and pilot drills, step drills
FAQ
What is the difference between hss and solid carbide drill bits?
HSS drill bits offer toughness and resistance to breakage for general machining, while solid carbide drills provide higher wear resistance and are the preferred choice for high-speed, high-volume machining and hardened materials.
Which coatings improve tool life for industrial drilling?
Coatings such as TiN and TiAlN increase surface hardness and thermal stability; when combined with the correct drill geometry and, if available, internal coolant, they significantly extend the service life of drill bits.
Can these drill bits be used on CNC machining centres for deep holes?
Yes. Drill bits designed with optimised flute geometry and internal coolant supply are suited to deep-hole machining on CNC machining centres, ensuring controlled chip evacuation and heat management.
How should I choose between twist drills, solid carbide drills and indexable drills?
Select twist drills for general-purpose drilling, solid carbide drills for high-speed and hardened-material applications, and indexable drills for large-diameter holes where insert changes offer economic advantages.
Why choose Metav for drill bits and drilling solutions?
Metav offers a comprehensive selection of drill bits, twist drills and indexable drills combined with sector expertise, centralised supply from Emmerich and proven reliability across thousands of industrial customers.
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com