Precision short twist drills for exact, clean holes
The HSS-G short twist drill DIN 338 type N with a 135° split point and cross grind provides a versatile solution for metalworking, designed to deliver high concentricity and razor-sharp cutting edges for demanding production and workshop applications. Its ground, polished blank surface reduces friction and prevents built-up edge when machining soft, lubricious materials such as aluminium or plastics, while the flatter 135° point with cross grind improves self-centring and lowers feed force so that pre‑spotting is often unnecessary. This drill is ideal for handheld, bench and pillar drilling operations, combining excellent chip evacuation, consistent hole accuracy and robust performance.
7.7mm HSS-G Twist Drill DIN 338 ,short, bright finished, Type N - MetavCUT
Twist Drill — Short Twist Drill Ø 7.7 mm, 135° Tip, Type N, Bright finished, Short, HSS‑G, DIN 338 The Twist Drill is a short Type N metalworking drill designed for precision drilling in hard materials and suited for use with a Drilling Machine. Short design for increased stiffness Ground HSS for faster, precise drilling 135° tip angle for reduced walking in hard materials Fully ground shank for high runout accuracy Conforms to DIN 338 for consistent quality Greater Precision through a Short, Stable Design A shorter geometry reduces the exposed length and therefore the tendency to bend, delivering noticeably better stability during machining. The short configuration of this twist drill makes it especially effective for precise work in metal, where less vibration and improved concentricity yield cleaner holes. Users benefit from improved control when working on tight setups or thin workpieces, since the reduced cantilever minimizes deflection and tool chatter. Faster Cutting with Ground HSS for Hard Materials The HSS‑G ground geometry enables higher cutting performance: up to 40% faster penetration and lower required feed force compared with conventional HSS designs, according to manufacturer data. This feature is particularly advantageous when drilling alloyed and unalloyed steel, cast iron, sintered materials and hard plastics. The ground flute geometry also produces sharper cutting edges and consistent chip evacuation, which supports longer tool life under appropriate cooling. Optimised Tip Geometry for Accurate Starts A 135° tip angle is recommended for harder workpiece materials because it shortens the initial cutting time and reduces the risk of punch‑through and tip wandering. The Type N normal spiral is a classic metal drill geometry, providing reliable centring and consistent chip removal for a wide range of metallic applications. For users unfamiliar with tip angles: a larger angle means a flatter point that spreads cutting action over a wider area, which reduces pressure per unit area at the entry. Compatibility, Standards and Practical Use Manufactured to DIN 338, this short twist drill matches established dimensions and tolerances for short cylindrical shank drills, easing integration into workshop inventories. The fully ground shank improves run‑out accuracy in chucks and sleeves, which is critical for high‑precision drilling operations. Although mainly intended for stationary or hand Drilling Machines, the design supports use in many standard metalworking environments when appropriate clamping and cooling are applied. Who Benefits and How to Apply It Professional machinists and skilled hobbyists who need accurate holes in hard or alloyed metals will appreciate the combination of stiffness and sharp cutting geometry. When drilling, ensure adequate coolant or lubrication for tough materials and moderate spindle speeds to keep temperatures down; reducing thermal load preserves edge life on the HSS‑G material. For tasks that require extreme impact or interrupted cuts, consider machine setup and feed rates to avoid brittle fracture of the ground tool. We recommend the MetavCUT Twist Drill for precision metalworking applications — for personalised technical advice or to confirm suitability for your task contact METAV Werkzeuge at info@metav-werkzeuge.com or call +49 2822 7131930 or WhatsApp +49 170 2837271 Designation: Twist Drill Brand: MetavCUT SKU: 45077-FDA Diameter: 7.7 mm Spiral Length: 75 mm Total Length: 117 mm Tip Angle: 135° Type: Type N Execution: Short Shaft Finish: Fully ground Colour: Bright finished Material: HSS‑G Norm: DIN 338 Application: Drills for metal For Drilling Machine: Drilling Machine Model Series: Standard Line Manufacturer: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What is the Twist Drill used for? The MetavCUT Twist Drill (Type N) is primarily used for machining high‑strength materials and larger drill diameters; its short execution and ground geometry make it suitable for precise metalworking tasks where stability and accurate holes are required. The shape allows easier resharpening and reliable performance under appropriate cooling. Which three drill types exist? Generally, drills are grouped as metal drills, wood drills and stone/concrete drills; the MetavCUT Twist Drill belongs to the metal drill category and is optimised for metals rather than masonry or softwood applications. Can the Twist Drill be used in wood? The MetavCUT Twist Drill can be used in wood, but as a metal drill it offers less guidance and a rougher finish compared with dedicated wood drills; it is easier to resharpen and exhibits lower self‑feeding, so results may be acceptable for rougher wood work but not for fine woodworking finishes.
7.8mm HSS-G Twist Drill DIN 338 ,short, bright finished, Type N - MetavCUT
Kompakte Konstruktion und geschliffene HSS-Geometrie sorgen für schnelle, präzise Bohrungen in Stahl bei reduziertem Anpressdruck. Nutzen Sie die Kombination aus hoher Stabilität durch kurze Ausführung und dem 135° Spitzenwinkel für härtere Werkstoffe. Bestellen Sie den Bohrer direkt bei Metav oder fragen Sie unsere Beratung an. Spiralbohrer | kurzer HSS‑G Bohrer von MetavCUT Standard Line Der Spiralbohrer kurz eignet sich für präzise Metallbearbeitung an Handbohrmaschine und stationären Maschinen und vereint Stabilität mit schnellem Vorschub HSS-G, geschliffen für hohe Präzision 135° Spitzenwinkel für härtere Werkstoffe Kurze Ausführung für erhöhte Stabilität Zylinderschaft: ideal für Handbohrmaschine Spirallänge 75 mm für verlässliche Spanabfuhr Hohe Schnittleistung dank geschliffener HSS-Geometrie Das Material HSS-G steht für Schnellarbeitsstahl mit geschliffener Spannutengeometrie, was scharfe Schneiden und hohe Rundlaufgenauigkeit ermöglicht. Durch die geschliffene Ausführung reduziert sich der Anpressdruck spürbar, wodurch das Bohren bis zu 40 % schneller erfolgen kann und gleichzeitig etwa 50 % weniger Anpresskraft erforderlich ist. Dieser Vorteil führt zu geringerer Bedienermüdung und konstanter Bohrungsqualität. Zuverlässigkeit bei härteren Werkstoffen durch 135° Spitzenwinkel Für legierte und unlegierte Stähle ist der 135° Spitzenwinkel ideal, weil er die Anbohrphase verkürzt und das Wanderverhalten verringert. Für Anwendungen in Edelstahl, Gussstahl oder Temperguss empfiehlt sich dieser Winkel, kombiniert mit Kühlschmierstoff und moderater Schnittgeschwindigkeit. Der Bohrer eignet sich damit besonders für Werkstatt‑ und Montageeinsätze, bei denen zügiges und sauberes Arbeiten zählen. Kurze Ausführung für maximale Stabilität und Präzision Die kurze Bauform mit einer Gesamtlänge von 117 mm und einer Spirallänge von 75 mm reduziert die Auskragung aus dem Bohrfutter und minimiert Verbiegevorgänge. Das Ergebnis sind präzisere Bohrbilder und bessere Rundlaufwerte, besonders wichtig bei sichtbaren oder passungsgebundenen Bohrungen. Deshalb ist diese Ausführung erste Wahl für stationäre Säulenbohrmaschinen und Handbohrmaschinen, die mit konstanter Führung arbeiten. Praxisorientierte Hinweise für effektive Anwendung Für besten Verschleißschutz und optimale Spanabfuhr wird Kühlung empfohlen, vor allem bei tiefen Bohrungen und harten Werkstoffen. Vorbohren mit einem Zentrierbohrer verbessert die Zuverlässigkeit, und kontrollierte Vorschubraten verlängern die Lebensdauer. Der Spiralbohrer kurz eignet sich für dünne bis mittlere Bleche sowie für allgemeine Stahlbearbeitung im Standard‑Bereich. Empfehlung: Die MetavCUT Lösung wählen — den kurzen HSS‑G Spiralbohrer direkt beim Metav Team anfragen per E‑Mail info@metav-werkzeuge.com oder Telefon +49 2822 7131930 für technische Beratung und Lieferoptionen Produktmerkmale Artikelnummer: 45078-FDA Marke: MetavCUT Serie: Standard Line Fakten Durchmesser: 7,8 mm Gesamtlänge: 117 mm Spirallänge: 75 mm Spitzenwinkel: 135° Besonderheiten Material: HSS-G (Schnellarbeitsstahl, geschliffen) Norm: DIN 338 Typ: Typ N (Normalspirale, Metall) Ausführung: kurz Schaftausführung: geschliffen (Zylinderschaft) Farbe: blank (blankfinish) Verwendung: Bohrer für Metall Für Bohrmaschine: Handbohrmaschine Verpackungseinheit: 10 FAQ Für welche Materialien ist dieser Spiralbohrer optimal geeignet? Der MetavCUT Spiralbohrer (Standard Line) mit HSS-G und 135° Spitzenwinkel ist ausgelegt für legierte und unlegierte Stähle, Gussstahl, Gusseisen sowie Nichteisenmetalle und Hartkunststoffe; bei harten Werkstoffen empfiehlt sich Kühlung. Eignet sich der Bohrer für Handgeführte Geräte? Ja, der kurze Spiralbohrer ist wegen geringerer Auskragung stabiler und eignet sich für Handbohrmaschine; bei sensiblen Passungen ist eine Führung oder Säulenbohrmaschine empfehlenswert. Welche Norm und Fertigungsart liegen diesem Bohrer zugrunde? Der Bohrer entspricht der Norm DIN 338 und ist als geschliffener HSS‑Bohrer (HSS‑G) ausgeführt, was sehr scharfe Kanten und hohe Rundlaufgenauigkeit ermöglicht. Wie wirkt sich der 135° Spitzenwinkel in der Praxis aus? Der 135° Spitzenwinkel verkürzt die Anbohrzeit und reduziert das Wandern beim Ansetzen, besonders vorteilhaft bei Edelstahl und härteren Stählen. Welche Abmessungen haben Gesamtlänge und Spirallänge? Die Gesamtlänge beträgt 117 mm bei einer Spirallänge von 75 mm, was die Stabilität erhöht und für verlässliche Spanabfuhr sorgt.
7.9mm HSS-G Twist Drill DIN 338 ,short, bright finished, Type N - MetavCUT
Twist Drill — Type N, Diameter 7.9 mm, 135° Point, Short, Bright Finished, Fully Ground Shank, HSS‑G, DIN 338 by MetavCUT A short Twist Drill (Type N) designed for precise metal drilling in Drilling Machines and industrial workshop applications. Short design for high stability and precision 135° tip for harder materials and reduced wander HSS‑G ground geometry for faster drilling and less feed force Fully ground shank for excellent runout accuracy Conforms to DIN 338 for short cylindrical shank drills Precision and stability for demanding metalwork The short execution of this Twist Drill delivers significantly reduced overhang, which increases Stability and minimises bending during cutting. That compact geometry together with a 135° point reduces the initial skidding when entering hard materials, allowing more accurate positioning and cleaner holes. For workshop professionals this means fewer re‑drills and consistent hole quality when working with alloyed and unalloyed steels. Faster cutting and lower operator effort thanks to HSS‑G The HSS‑G (ground) material and CNC‑ground flute geometry provide sharper cutting edges and a high Rundlaufgenauigkeit, enabling up to 40% faster drilling with roughly 50% lower feed force compared with conventional HSS variants. For operations in Steel, Cast Iron, Sintered Iron and other non‑ferrous metals, this translates into shorter cycle times and less operator fatigue, particularly in repetition tasks on production benches or machine tools. Engineered shank and finish for machine compatibility With a fully ground shank and bright finished coating, the drill achieves excellent clamping accuracy and smooth insertion into chucks. The nominal Spiral Length of 75 mm and an Overall Length of 117 mm balance chip evacuation and stiffness. Use in stable chucks or machine tool setups is recommended to exploit the drill’s precision; the robust finish also eases handling and reduces corrosion risk in workshop environments. Recommended users and application scenarios This product targets machinists, toolrooms and maintenance professionals who require precise, repeatable metal drilling. The Type N normal spiral geometry is optimised for metalworking and is particularly effective when used with stationary drilling machines or robust portable drilling equipment under controlled conditions. For demanding tasks such as stainless steel or tempered components, the short Twist Drill offers reliability and a longer life under appropriate cooling. For precise metalworking choose MetavCUT’s Twist Drill Type N — if you are unsure whether this tool meets your needs or require further technical data, METAV Werkzeuge offers competent advice: info@metav-werkzeuge.com | Tel. +49 2822 7131930 | WhatsApp +49 170 2837271 Designation: Twist Drill Marke: MetavCUT SKU: 45079-FDA Diameter: 7.9 mm Overall length: 117 mm Spiral length: 75 mm Point angle: 135° Type: Type N Execution: Short Shank: Fully ground Material: HSS‑G Finish: Bright finished Application: Drills for metal; suitable for Drilling Machine use Standard: DIN 338 Model series: Standard Line Colour: Bright finished Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ Can I use the MetavCUT Twist Drill Type N in a hand drill? The MetavCUT Twist Drill Type N is optimised for machine use and offers best results when used in stable chucks or drilling machines; however, it can be used in powerful hand drills for light tasks if proper clamping, low speeds and cooling are applied to maintain precision and avoid breakage. For what is a Twist Drill used? The Twist Drill by MetavCUT is primarily applied to machining high‑strength materials and larger bore diameters; its ground geometry is easy to re‑sharpen and withstands substantial loads, making it suitable for alloyed and unalloyed steel, cast irons and hard plastics. Which 3 drill types exist? For reference, the main drill categories are Metal drills, Wood drills and Masonry/Concrete drills, and the MetavCUT Twist Drill belongs to the Metal drill group.
7mm HSS-G Twist Drill DIN 338 ,short, bright finished, Type N - MetavCUT
Twist Drill (Type N) — 7 mm, 135° Point Angle, Short, Bright finished, HSS-G, DIN 338 A Twist Drill (Type N) designed for precise metal drilling in Drilling Machines, offering a short, stable geometry for work on hard materials. Short design for improved stability HSS-G material for high cutting performance 135° point angle for hard materials Fully ground shank for excellent runout accuracy Durable HSS-G construction for faster, cleaner holes The HSS-G material of this Twist Drill ensures high wear resistance and reliable cutting behaviour when machining Steel and other Alloys. Because the flute geometry is produced by CNC grinding, the tool achieves very sharp cutting edges and a high concentricity, which translates into cleaner holes and longer tool life under correct cutting conditions. Users will benefit from up to 40% faster drilling and about 50% less feed force compared with conventional HSS designs, provided adequate coolant and appropriate speeds are used. Short overall length increases precision and reduces vibration A shorter design reduces the exposed overhang and therefore minimizes bending and chatter during operation. This results in higher positional accuracy and makes the drill particularly suitable for precise work in hardened materials such as Stainless Steel. The designation to DIN 338 confirms the geometry and format as a short Twist Drill with a Cylindrical Shank, ensuring compatibility with common chucks and fixtures in metalworking shops. Geometry optimised for metalworking and hard materials The 135° point angle is tailored to reduce initial drilling forces and improve centring in tough materials, shortening pilot time and improving surface finish in the hole. As a Type N (normal spiral) drill, this tool is engineered primarily for Metal applications including Cast Iron, Sintered Iron, Tempered Castings, Non-Ferrous Metals and Hard Plastics. For best results, use on stationary or machine-mounted Drilling Machines and apply appropriate cooling to avoid tempering the cutting edge. Target users and handling recommendations Workshop professionals, toolroom technicians and demanding hobbyists will appreciate the combination of a short flute length and a fully ground shank that delivers consistent runout and repeatable hole quality. To avoid brittleness-related breakage, operate the Twist Drill with steady feed, adequate coolant and secure clamping. Ground drills can be re-sharpened more easily than rolled equivalents, maintaining edge quality and service life when reconditioned correctly. We recommend the MetavCUT Twist Drill for precise metalworking applications; for technical advice or to confirm suitability for a specific material or machine, METAV Werkzeuge provides expert consultation – eMail: info@metav-werkzeuge.com | Tel: +49 2822 7131930 | WhatsApp: +49 170 2837271 Designation: Twist Drill Brand: MetavCUT SKU: 45070-FDA Diameter: 7 mm Point Angle: 135° Type: Type N Execution: Short Finish: Bright finished Shank Execution: Fully ground Material: HSS-G Norm: DIN 338 Spiral Length: 69 mm Total Length: 109 mm For Drilling Machine: Drilling Machine Application: Drills for metal Model Series: Standard Line Manufacturer: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What are Twist Drills used for? The MetavCUT Twist Drill is primarily used for machining high-strength materials and larger hole diameters. Its ground geometry is easy to re-sharpen and withstands higher loads, making it suitable for demanding metalworking tasks where durability and precision are required. Which three drill types exist? For context, the MetavCUT Twist Drill belongs to the metal-drill category. The three main drill types are Metal drills, Wood drills and Stone/Concrete drills.
8.1mm HSS-G Twist Drill DIN 338 ,short, bright finished, Type N - MetavCUT
Twist Drill — Type N short, Ø 8.1 mm, 135° point angle, Bright finished, Short execution, DIN 338, HSS‑G (MetavCUT) A Twist Drill (Type N) designed for precise metal drilling on drilling machines and stationary machine tools. Short design for higher stability and precision HSS‑G fully ground for sharp, clean holes 135° point angle suited for hard materials like stainless steel Conforms to DIN 338 for short twist drills Short overall length reduces vibration and deflection Greater Stability and Faster Drilling for Metalwork The short design of this Twist Drill delivers increased Stability and reduced deflection when working with hard materials. Shorter overhang from the Chuck improves concentricity and lowers the risk of bending, which directly raises hole accuracy. In many industrial applications the HSS‑G ground geometry achieves up to 40% faster drilling and requires 50% less feed force compared with conventional HSS drills, so productivity improves while Operator fatigue decreases. Precise Tip Geometry for Tough Materials A 135° point angle optimises entry into hard and abrasion‑resistant metals by reducing the initial bite and spreading heat. For less experienced users: the point angle is the cone at the Drill Tip that influences how quickly the tool penetrates and how well it centres. With Type N normal spiral geometry this tool balances cutting speed and chip evacuation, making it particularly effective for Stainless Steel, Cast Iron and Alloyed Steels. Engineered Finish and Compliance for Reliable Results The fully ground flute and land geometry (HSS‑G) produce very sharp cutting edges and excellent Runout accuracy, yielding cleaner holes and longer life under correct conditions. The product conforms to DIN 338, which classifies short Twist Drills with cylindrical shanks and specifies manufacturing tolerances and execution variants. This standardisation supports reproducible setup and interchangeability in workshop environments. Recommended Use and Machine Compatibility Designed primarily for machining metal, this Twist Drill suits both stationary machine tools and drilling machines; it is most effective when used with appropriate cutting speeds, coolant and steady clamping. For hand‑held Drilling Machines take care with feed and torque limits because fully ground HSS drills can be more brittle than rolled variants; cooling and moderate speeds extend tool life. Typical applications include holes in unalloyed and alloyed steels, castings, sintered parts and hard plastics. Material Care and Maintenance Tips The HSS‑G material benefits from correct machining parameters: use steady coolant/lubrication for deep or high‑speed holes, and avoid excessive pecking without coolant to prevent heat build‑up. The fully ground geometry makes re‑sharpening straightforward for experienced toolmakers, while maintaining concentricity is essential to prevent premature breakage. For best performance, inspect the Twist Drill for wear and micro‑chipping before each critical operation. Strong recommendation: Choose the MetavCUT Twist Drill (Type N, HSS‑G) for demanding metal drilling tasks and contact METAV Werkzeuge for expert advice and application support — 📧 info@metav-werkzeuge.com ☎️ +49 2822 7131930 ✔️ WhatsApp +49 170 2837271 Twist Drill Marke: MetavCUT SKU: 45081-FDA Diameter: 8.1 mm Point angle: 135° Type: Type N Colour: Bright finished Execution: Short Spiral length: 75 mm Total length: 117 mm Shank execution: Fully ground Material: HSS-G Standard: DIN 338 For drilling machine: Drilling Machine Application: Drills for metal Model series: Standard Line Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What is the MetavCUT Twist Drill used for? The MetavCUT Twist Drill (Type N) is primarily used for drilling metal; it excels in producing precise holes in alloyed and unalloyed steels, cast components and hard plastics when used on drilling machines or stationary machine tools. Can the MetavCUT Twist Drill be used in a hand drill? The MetavCUT Twist Drill can be used in a hand drilling machine with caution; due to its short, fully ground HSS design it performs best in well‑supported setups and benefits from controlled feed, cooling and firm clamping to avoid breakage. For what is a Twist Drill used? Twist Drills are mainly applied to machining high‑strength materials and larger diameters; their form is easy to re‑grind and they withstand greater loads, making them suitable for demanding metalwork. Which three drill types exist? There are three main drill types: Metal drills, Wood drills and Stone/Concrete drills. Why are Twist Drills sharpened (pointed)? Sharpening reduces the cross‑cut at the tip, which lowers friction and the required feed force while improving the drill’s centring in the workpiece. Can you drill wood with a Twist Drill? Metal drills can be used in wood, but they offer poorer guidance and a less clean finish; however, they are easier to resharpen and have lower self‑feed tendencies. At which drilling depths is the Twist Drill most commonly used? Solid drilling is commonly executed with Twist Drills; they are most frequently the tool of choice for diameters up to 20 mm and drilling depths up to 100 mm. Is HSS or HSSE better? The general belief that HSSE is always superior to HSS is incorrect; choice should be based on the specific working conditions and whether those conditions justify the higher cost of HSSE.
8.25mm HSS-G Twist Drill DIN 338 ,short, bright finished, Type N - MetavCUT
Twist Drill — Short HSS‑G Twist Drill, Diameter 8.25 mm, 135° tip, Type N, Bright finished, Fully ground shank, DIN 338 The Twist Drill short HSS‑G Type N is a compact metal‑drilling tool designed for precise work in hard materials, suitable for use in a Drilling Machine. Short design for higher rigidity and precision HSS‑G material for sharp, clean metal holes 135° tip for improved entry in hard materials Fully ground shank for excellent runout accuracy Compliant with DIN 338 for short twist drills Precision and stability for demanding metalwork The short HSS‑G Twist Drill from MetavCUT combines a reduced overhang with a robust geometry to deliver reliable concentricity and minimal deflection. Its short design reduces the unsupported length outside the chuck, which translates into higher stability and better hole accuracy when machining steels and other hard materials. For workshop and industrial applications where repeatable hole quality matters, this configuration helps maintain machining tolerances and reduces scrap rates. Faster penetration with lower feed force A HSS‑G (ground high speed steel) construction and a 135° tip angle optimise the cutting action for tougher metals, shortening the initial entry phase and lowering required thrust. The ground flute geometry provides sharp cutting edges that support faster drilling — the design enables up to around 40% faster progress and reduces required feed forces compared with conventional HSS variants, making the short drill particularly effective for alloyed and unalloyed steel, cast materials and hardened plastics. Explanation: ground (G) means the flutes are CNC‑ground rather than roll‑formed, yielding sharper edges and improved runout accuracy. Designed for metal, tailored to professional use As a Type N normal spiral, this short twist drill is engineered primarily for metalworking on stationary or portable Drilling Machines. Typical applications include drilling in steel, cast steel, cast iron, sintered iron and non‑ferrous metals. The fully ground shank supports precise clamping and is advantageous in production environments where high concentricity and repeatability are required. For less experienced users: Type N indicates a general‑purpose metal drill with a standard spiral suited to a wide range of ferrous materials. Norm conformity and manufacturing details that matter Compliance with DIN 338 identifies this tool as a short twist drill with a cylindrical shank produced to standardised dimensions and tolerances. The bright finished surface and the fully ground shaft contribute to predictable seating in chucks and collets. Because ground HSS variants can be more brittle than rolled types, cooling and controlled feeds are recommended for stationary operations to maximise tool life. The short length also reduces vibration, improving surface finish and hole roundness in high‑precision tasks. Strong recommendation: MetavCUT short HSS‑G Twist Drill for professional metal drilling — for technical advice or to confirm suitability for a specific application, contact METAV Werkzeuge for competent consultation via eMail: info@metav-werkzeuge.com, Phone: +49 2822 7131930, WhatsApp: +49 170 2837271 Bezeichnung: Twist Drill Marke: MetavCUT SKU: 450825-FDA Typ: Type N Durchmesser: 8.25 mm Gesamtlänge: 117 mm Spirallänge: 75 mm Spitzenwinkel: 135° Material: HSS-G Ausführung: short Schaft Ausführung: fully ground Farbe: bright finished Norm: DIN 338 Für Bohrmaschine: Drilling Machine Modellserie: Standard Line Anwendung: Drills for metal Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What is the ideal use of the Twist Drill by MetavCUT? The MetavCUT Twist Drill short HSS‑G is primarily used for machining high‑strength materials and larger drill diameters; its ground geometry makes it easy to regrind while withstanding greater loads, which suits heavy‑duty metalworking tasks. Which three drill types exist? When classifying common drills, there are Metal drills, Wood drills and Stone/Concrete drills; the MetavCUT Twist Drill belongs to the Metal drill category and is optimised for that purpose. Why are twist drills point‑sharpened? The point sharpening on a MetavCUT Twist Drill reduces the cross‑edge at the tip, which significantly lowers friction and therefore the required feed force, and it improves centring in the workpiece for more accurate starts. Can a Twist Drill for metal be used to drill wood? A MetavCUT metal Twist Drill can be used in wood, but it offers less guidance and a rougher finish than a purpose‑built wood drill; metal drills are easier to re‑sharpen and have less self‑feeding action. For which drilling depths is the Twist Drill commonly used? A through hole in solid material is typically made with a Twist Drill; for diameters up to around 20 mm and drilling depths up to about 100 mm, the short twist drill form is the most frequently used tool. Which is better, HSS or HSSE? The general belief that HSSE steels are inherently superior to HSS is not universally correct. Evaluate working conditions to determine whether HSSE justifies a higher cost; MetavCUT recommends choosing material and coating based on specific machining demands.
8.2mm HSS-G Twist Drill DIN 338 ,short, bright finished, Type N - MetavCUT
Twist Drill — Type N short, 8.2 mm, 135°, HSS‑G, Bright Finished, Fully Ground Shank, DIN 338 The Twist Drill Type N short is a precision metal‑drilling tool for Drilling Machines, offering an 8.2 mm diameter and a 135° tip for reliable penetration in hard materials. Twist Drill Type N, 8.2 mm, 135° tip Short design for higher stability and precision HSS‑G ground for fast drilling and clean holes Sized to machine drilling in metals per DIN 338 Bright finished with fully ground shank Short design increases accuracy and reduces vibration A shorter overall length combined with a reduced overhang provides noticeably higher stability during machining, which is particularly advantageous when working on tough alloys. The compact geometry lowers the tendency to bend or chatter, so operators achieve more consistent hole quality under load. For workshop set‑ups where rigidity matters, the short execution of this tool supports precise centring and smoother feeds. HSS‑G ground geometry for faster, cleaner holes in metal The HSS‑G (ground high‑speed steel) construction yields very sharp cutting edges and excellent roundness, enabling up to 40% faster drilling speeds with significantly reduced feed forces compared with conventional HSS. Combined with the 135° tip geometry, the tool is optimised for harder materials and reduces the risk of workpiece deformation while improving tool life when used with appropriate coolant. Fully ground shank and bright finish for reliable clamping A fully ground cylindrical shank ensures uniform clamping in chucks and holders, minimising run‑out and enhancing concentricity for deeper or repeated bores. The bright finished surface facilitates chip evacuation and inspection, while the compliance with DIN 338 confirms the tool class and dimensional tolerances expected in professional metalworking environments. Best suited for professional metalworking and demanding tasks Engineers and machinists who require robust performance in steel, castings and non‑ferrous metals will appreciate the balance of durability and precision offered by this Type N Twist Drill. The tool is designed primarily for machine drilling operations and excels where repeatable accuracy and clean bore edges are required, for example in toolrooms, maintenance shops and production lines. Choose the MetavCUT Twist Drill Type N short with HSS‑G grind for demanding metal applications — for expert advice and application support contact METAV Werkzeuge at info@metav-werkzeuge.com or call +49 2822 7131930, WhatsApp +49 170 2837271 Designation: Twist Drill Brand: MetavCUT SKU: 45082-FDA Diameter: 8.2 mm Tip angle: 135° Type: Type N Material: HSS-G Execution: short Spiral length: 75 mm Total length: 117 mm Shank finish: fully ground Colour / Finish: bright finished Application: Drills for metal Model series: Standard Line Standard: DIN 338 Shaft execution: geschliffen Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What applications is the Twist Drill Type N suitable for? The MetavCUT Twist Drill Type N is intended primarily for metalworking operations; it is particularly effective when machining steels, cast irons and other harder materials on Drilling Machines, offering stable performance for precision bores. Can the Twist Drill be used in portable drills? While the Twist Drill Type N is designed for machine drilling, it can be used in Handheld Drilling Machines for lighter tasks; however the short geometry shows its full advantages in rigid, machine‑mounted setups to maintain concentricity and hole quality. For what is Twist Drill used? The Twist Drill is mainly applied to the machining of high‑strength materials and larger drill diameters. This shape is easy to regrind and withstands higher loads. Which 3 drill types exist? There are three principal drill types: Metal drills, Wood drills, and Stone/Concrete drills. Why are Twist Drills pointed (regrinded)? Pointing reduces the web thickness at the tip of the Twist Drill. By pointing, frictional forces are substantially lowered so that smaller feed forces are required and the tip centres better in the workpiece. Can a metal drill be used to drill wood? A metal drill can be used in wood but typically gives poorer guidance and a less clean result. However, such drills are easier to resharpen and exhibit less aggressive self‑feeding.
8.3mm HSS-G Twist Drill DIN 338 ,short, bright finished, Type N - MetavCUT
Twist Drill — Short Type N Drill for Metal, 8.3 mm, 135° Point Angle, Bright Finish, HSS‑G, DIN 338 The Twist Drill (Short, Type N) is a precision drill for metalwork, optimised for stable, high‑performance drilling on drilling machines. Short design for increased stability 135° point angle for hard materials HSS‑G fully ground for sharp cutting edges Fully ground shank for precise chucking Conforms to DIN 338 for standardised quality Faster, cleaner holes thanks to ground HSS technology The short design in combination with HSS‑G (ground high speed steel) reduces cutting resistance and produces very sharp edges, enabling up to 40% faster drilling and requiring around 50% less feed force compared with conventional HSS drills. This results in cleaner hole edges and less heat buildup during interrupted drilling. The ground geometry is produced by CNC grinding, which improves roundness and repeatability, making it ideal where consistent hole quality matters. Greater stability and accuracy when working harder materials A reduced overhang and compact spiral length mean the cutter is less prone to deflection; this short format therefore delivers superior precision when machining steel and similar materials. The 135° point angle is optimised for harder workpieces such as stainless and alloyed steels, while the Type N normal spiral is the classic configuration for metal drilling. The geometry helps centre the tool reliably and reduces walking at the start of the hole. Practical guidance for prolonged tool life and optimal results For best performance use on a suitable drilling machine with correct clamping and, where appropriate, coolant or cutting fluid to control temperature. The fully ground shank ensures accurate holding in the chuck and minimises runout; however, ground HSS can be more brittle than rolled designs, so avoid excessive lateral loads and abrupt shocks. Re‑sharpening is possible but should follow the original geometry to preserve the 135° tip profile and cutting rake. Who benefits: precision metalworkers and maintenance professionals This short drill is aimed at professional machinists, toolroom staff and maintenance technicians who require reproducible holes in a range of metals. Key dimensions provide clear handling and setup advantages: Diameter 8.3 mm, Spiral Length 75 mm, Overall Length 117 mm, bright finish for corrosion resistance and easy identification. The construction and conformity to DIN 338 make it a reliable choice for production and repair environments. For precise metalworking choose MetavCUT's Twist Drill — expert advice and support are available from METAV Werkzeuge: info@metav-werkzeuge.com • +49 2822 7131930 • WhatsApp +49 170 2837271 Designation: Twist Drill (Short, Type N) Brand: MetavCUT SKU: 45083-FDA Diameter: 8.3 mm Spiral Length: 75 mm Overall Length: 117 mm Point Angle: 135° Type: Type N Execution: short Material: HSS-G Shank Finish: fully ground Colour / Finish: bright finished Application: Drills for metal Suitable For: drilling machine Model Series: Standard Line Norm / Standard: DIN 338 Manufacturer Contact: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What is the Twist Drill used for and which materials is it suitable for? The Twist Drill from MetavCUT is primarily used for machining metal; it is especially suited to alloyed and unalloyed steel, cast steel, cast iron, sintered iron, non‑ferrous metals and hard plastics. Its short design and ground geometry make it appropriate for precise operations on drilling machines where stability and clean holes are required. Which three drill types are commonly distinguished? In general classification the main drill groups are metal drill, wood drill, and stone/concrete drill. MetavCUT's Twist Drill belongs to the metal drill category and is engineered specifically for metalworking applications.
8.4mm HSS-G Twist Drill DIN 338 ,short, bright finished, Type N - MetavCUT
Kompakte Stabilität und präzise Schnittleistung machen diesen Spiralbohrer zu einer zuverlässigen Wahl für metallische Werkstoffe; die Kürzere Ausführung reduziert Auslenkung, während HSS-G und der 135° Spitzenwinkel saubere Bohrbilder in Stahl ermöglichen. Bei Fragen zur Eignung steht die Beratung von Metav gern zur Verfügung oder bestellen Sie direkt über Metav. Spiralbohrer von MetavCUT – kurzer HSS-G Metallbohrer Der Spiralbohrer von MetavCUT ist ein kurzer, geschliffener HSS-Bohrer nach DIN 338, entwickelt für präzise Metallbohrungen an stationären und handgeführten Maschinen. Hohe Stabilität durch kurze Ausführung Geschliffen für präzise Bohrbilder Geeignet für legierte und unlegierte Stähle 135° Spitzenwinkel für harte Werkstoffe Zylinderschaft für sichere Spannaufnahme Mehr Stabilität bei präzisen Metallbohrungen Die Kürzere Ausführung reduziert die Auskraglänge und führt zu erhöhter Stabilität sowie geringerer Neigung zum Verbiegen. Das Ergebnis sind sauberere Bohrungen und längere Werkzeugstandzeiten bei Anwendungen in Stahl und Guss. Die kompakte Geometrie erleichtert das Führen an Handbohrmaschine und Säulenbohrmaschine, weil die Krafteinleitung direkter erfolgt und die Werkstückaufspannung weniger kritisch wird. Für Anwender bedeutet das geringeren Ausschuss und gleichbleibende Bohrqualität. Geschliffene Geometrie für saubere Ergebnisse Der geschliffen ausgeführte HSS-G sorgt für sehr scharfe Schneiden und hohe Rundlaufgenauigkeit, was saubere, präzise Bohrlöcher fördert. Der CNC-Schliff ermöglicht eine konstante Spanabfuhr und reduziert Wanderneigung beim Anbohren. Zu beachten ist, dass geschliffene Bohrer empfindlicher gegenüber Schlagbelastung sind; deshalb empfiehlt sich die Nutzung von Kühlschmierstoff und eine stationäre Spindel bei harten Werkstoffen, um die Lebensdauer zu maximieren. Passende Anwendungen und Zielgruppe Dieser kurze Spiralbohrer ist für Werkstätten, Montage und industrielle Anwendungen konzipiert, insbesondere für das Bohren in legierten und unlegierten Stahl, Gusseisen sowie Nichteisenmetallen. Die Kombination aus HSS-G und Typ N macht das Werkzeug ideal für Anwender, die robusten Metallbohrbedarf mit präzisen Ergebnissen verbinden wollen. Die Ausführung mit Zylinderschaft gewährleistet die Kompatibilität zu Standardspannfuttern. Praxistipps für sicheres Bohren und lange Standzeit Vor dem Bohren bei hoher Genauigkeit empfiehlt sich ein Anpunkten mit einem Zentrierbohrer, um die Querschneide zu entlasten. Bei Durchmesser im Standard-Bereich direkt bohren; bei kritischer Maßhaltigkeit ruhig mit langsamerem Vorschub und ausreichender Kühlung arbeiten. Für die Bearbeitung von Edelstahl macht der 135° Spitzenwinkel das Anbohren leichter und reduziert Aufschweißen an der Schneide. Empfehlung: Für präzise Metallbohrungen die MetavCUT Standard Line verwenden und bei Unsicherheit technische Beratung über info@metav-werkzeuge.com oder Telefon +49 2822 7131930 einholen. Produktmerkmale Artikelnummer: 45084-FDA Marke: MetavCUT Serie: Standard Line Norm: DIN 338 Typ: Typ N Fakten Durchmesser: 8,4 mm Spirallänge: 75 mm Gesamtlänge: 117 mm Spitzenwinkel: 135° Besonderheiten Material: HSS-G — Schnellarbeitsstahl, geschliffen Schaft Ausführung: geschliffen — Zylinderschaft für Standardspannfutter Ausführung: kurz — Kürzere Auskraglänge für bessere Stabilität Farbe: blank — helle Oberfläche Für Bohrmaschine: Handbohrmaschine / stationäre Maschinen Verpackungseinheit: 5 FAQ Für welche Materialien eignet sich der Bohrer am besten? Der MetavCUT Standard Line Spiralbohrer (Typ N, SKU 45084-FDA) eignet sich besonders für legierten und unlegierten Stahl, Gusseisen sowie Nichteisenmetalle und Hartkunststoffe. Ist der Bohrer für Handgebrauch mit Akkubohrschrauber geeignet? Ja, die kurze Ausführung und der Zylinderschaft erlauben den Einsatz an Handbohrmaschine für typische Werkstattanwendungen; bei sehr hartem Material oder hohen Anforderungen an Maßgenauigkeit ist eine stationäre Maschine empfohlen. Warum ist der Bohrer geschliffen und welche Vorteile bringt das? Die geschliffene Geometrie (HSS-G) bietet schärfere Kanten und höhere Rundlaufgenauigkeit, was sauberere Bohrbilder und geringere Wanderneigung ermöglicht; dafür ist etwas schonendere Handhabung und Kühlung vorteilhaft. Welche Bedeutung hat der 135° Spitzenwinkel? Der 135° Spitzenwinkel reduziert das Aufschweißen beim Bohren in harten Werkstoffen wie Edelstahl und erleichtert das Eindringen, was Anbohrzeiten verkürzt und die Kraftanforderung senkt. Welche Normen und Serienzuordnung gelten für dieses Werkzeug? Der Bohrer entspricht der Norm DIN 338 und gehört zur MetavCUT Standard Line, was die Einordnung als kurzer Spiralbohrer mit Zylinderschaft bestätigt.
8.5mm HSS-G Twist Drill DIN 338 ,short, bright finished, Type N - MetavCUT
Twist Drill — Short Type N, Ø 8.5 mm, 135° Point, HSS‑G, Bright Finished, DIN 338 (MetavCUT) The Twist Drill Short Type N is a precision metalworking Drill for Drilling Machines, engineered for stable, fast and clean holes in hard materials. Short design for increased Stability and Precision HSS‑G material for clean holes in Metal 135° Point angle for harder Werkstoffe Fully ground Shank for low Runout Conforms to DIN 338 for standardized Reliability Faster, more stable drilling in metal workshops Die kurze Bauform des Werkzeugs erhöht die Stabilität und reduziert Schwingungen deutlich, sodass präzise Bohrungen auch bei hohen Schnittkräften möglich sind. Durch die HSS‑G Fertigung entstehen sehr scharfe Schneiden, die saubere Bohrbilder liefern und damit Nacharbeit minimieren. Diese Eigenschaft macht das Werkzeug besonders geeignet für anspruchsvolle Metallarbeiten wie in Maschinenbau und Feinwerkstatt. High performance on hard materials with reduced feed force Der 135° Point sorgt für besseren Anbohrverlauf in harten Werkstoffen und vermindert das Anfressen. Typ‑N‑Spiralgeometrie kombiniert mit geschliffener Oberfläche erlaubt bis zu 40% schnellere Bohrfortschritte bei gleichzeitig bis zu 50% reduzierter Anpresskraft, was die Produktivität erhöht und Ermüdung des Werkzeuges verringert. Ideal für legierte und unlegierte Stähle sowie Gusswerkstoffe. Compatibility and accuracy for drilling machines Die Ausführung als kurzer Spiralbohrer mit zylindrischem Schaft und fully ground Schaftoberfläche gewährleistet geringen Rundlauf und präzise Werkzeugführung in stationären und handgeführten Bohrmaschinen. Die Einhaltung der DIN 338 macht die Auswahl und Austauschbarkeit planbar und sorgt für reproduzierbare Ergebnisse in Serienprozessen. Who benefits: workshops, toolrooms and production Dieses Werkzeug ist konzipiert für Metallbearbeiter, Instandhalter und Produktionsstätten, die präzise, saubere Bohrungen in harten Materialien benötigen. Die Kombination aus Kurzbauweise, HSS‑G Material und Normkonformität bietet sich an, wenn Wiederholgenauigkeit und kurze Bearbeitungszeiten im Vordergrund stehen. METAVCUT‑Qualität unterstützt professionelle Anforderungen. Strong recommendation: Choose the MetavCUT Short Twist Drill for reliable, high‑precision metal drilling — for technical advice and support contact METAV Werkzeuge: 📧 info@metav-werkzeuge.com ☎️ +49 2822 7131930 ✔️ WhatsApp +49 170 2837271 Precise Technical Data for Planning and Procurement Designation: Twist Drill, Short, Type N, Diameter 8.5 mm Marke: MetavCUT SKU: 45085-FDA Diameter: 8.5 mm Overall Length: 117 mm Spiral Length: 75 mm Point Angle: 135° Material: HSS‑G Shank: Fully ground Finish: Bright finished For Drill Machine: Drilling Machine Norm: DIN 338 Execution: short Application: Drills for metal Manufacturer: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What is the Twist Drill used for and which materials suit it best? The MetavCUT Twist Drill Short Type N is primarily used for machining high‑strength materials and larger hole diameters; it excels in Metal such as alloyed and unalloyed Steel, Cast Steel, Cast Iron and Non‑ferrous Metals, delivering clean holes and high repeatability. Which three drill types exist? Common categories are Metal Drills (such as the MetavCUT Twist Drill), Wood Drills and Stone/Concrete Drills, each optimised in geometry and material for their specific workpiece classes. Why are Twist Drills sharpened at the tip? Tip sharpening reduces the cross‑edge at the Drill Tip, lowering friction so that smaller Feed Forces are required and improving centring of the Tip in the Workpiece for more accurate starts. Can a Twist Drill be used for wood drilling? A Metal Twist Drill can be used in Wood, but guidance and Hole Finish are typically inferior compared with dedicated Wood Drills. Metal Drills are easier to resharpen and have lower self‑feeding tendency.
8.6mm HSS-G Twist Drill DIN 338 ,short, bright finished, Type N - MetavCUT
Twist Drill (Spiralbohrer) — Ø 8.6 mm · 135° tip · Type N · Bright finished · Short · DIN 338 · HSS‑G · MetavCUT The Twist Drill is a short HSS‑G metal drill designed for precise drilling in hard materials on Drilling Machines. Short design for higher stability and precision Conforms to DIN 338 for short twist drills 135° tip optimised for hard materials Fully ground shank for high concentricity Up to 40% faster drilling with reduced feed force Deliver faster, cleaner holes with a short HSS‑G design The short Twist Drill construction reduces overhang and vibration, which directly improves stability and hole quality. Thanks to the HSS‑G (ground High Speed Steel) geometry, cutting edges are sharper and concentricity is higher than rolled alternatives, leading to more consistent hole diameters and less rework. The reduced tendency to wander makes this drill particularly effective when accuracy matters, for example when preparing holes for threaded fastenings in metal components. Precision at the tip: why 135° helps with hard materials A 135° tip angle increases the contact area at the point and reduces the initial penetration aggressiveness compared with steeper tips, which helps when drilling stainless steel, cast and alloyed steels or hard plastics. The Type N normal spiral is the classic metalworking geometry and provides reliable chip evacuation and centre guidance. In practice, this means fewer retries, reduced burr formation and a cleaner finish on the workpiece. Suitable machines and material range for consistent results This short Type N Twist Drill is intended for metalworking on rotating machines and is suitable for both stationary Drilling Machines and compatible portable setups when rigidity is ensured. It is recommended for alloyed and unalloyed steel, cast steel, cast iron, sintered iron, non‑ferrous metals and hard plastics. The fully ground shank ensures tight clamping and low runout, improving tool life and repeatability in production environments. Handling advice to maximise performance and tool life Ground HSS drills can be more brittle than rolled types; therefore, apply moderate feed and appropriate cutting fluid when machining metals to avoid premature breakage. Correct speed and steady feed are essential: slower speeds and continuous coolant are advised for harder alloys. For precise positioning, use a pilot or centre punch before drilling. If uncertain about speeds, feeds or machine setup, expert advice is available from METAV Werkzeuge to match operating conditions to material and hole requirements. Choose MetavCUT quality for precision metal drilling — for personalised technical advice and application support contact METAV Werkzeuge: info@metav-werkzeuge.com · Phone: +49 2822 7131930 · WhatsApp: +49 170 2837271 Designation: Twist Drill (Spiralbohrer) Brand: MetavCUT SKU: 45086-FDA Diameter: 8.6 mm Tip Angle: 135° Type: Type N Execution: Short Finish/Colour: Bright finished Material: HSS‑G Spiral Length: 75 mm Overall Length: 117 mm Shank Finish: Fully ground Standard: DIN 338 Intended Use: Drills for metal For Machine: Drilling Machine Model Series: Standard Line Manufacturer: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What is the MetavCUT Twist Drill used for? The MetavCUT Twist Drill (Type N) is primarily used for drilling in hard and high‑strength materials; it is especially suited to metalworking tasks such as holes in alloyed and unalloyed steel, cast steel, cast iron, sintered iron, non‑ferrous metals and hard plastics, where precision and stability are required. Which three drill types exist? The three main drill categories are Metal drill, Wood drill and Stone/Concrete drill; the MetavCUT Twist Drill belongs to the metal drill family and is optimised for machining metals. Why are twist drills pointed? The point geometry reduces the cross‑cut area at the tip, lowering friction and required feed forces; by sharpening (pointing) a Twist Drill the cutting forces decrease and the tip centres more reliably in the workpiece. Can a Twist Drill be used to drill wood? A metal Twist Drill can be used in wood, but the guidance is inferior and the hole finish is usually less clean compared with dedicated Wood drills; however, metal Twist Drills are easier to resharpen and show less self‑pulling action.
8.75mm HSS-G Twist Drill DIN 338 ,short, bright finished, Type N - MetavCUT
Kompakte Bauweise, geschliffene HSS‑Geometrie und 135° Spitzenwinkel sorgen für stabile, präzise Bohrungen in harten Werkstoffen. Die kurze Ausführung reduziert die Auslenkung und ermöglicht schnelleres Bohren bei geringer Anpresskraft. Bestellen Sie den Spiralbohrer direkt über Metav Werkzeuge oder fragen Sie unsere Beratung bei Bedarf an. Spiralbohrer kurz von MetavCUT, Typ N Der Spiralbohrer kurz eignet sich für präzise Metallbohrungen an stationären und handgeführten Maschinen und bietet hohe Stabilität bei harten Werkstoffen. HSS‑G geschliffen für hohe Schärfe und Rundlauf 135° Spitzenwinkel für harte Werkstoffe Kurze Ausführung erhöht Stabilität und Präzision Spirallänge 81 mm für sichere Spanabfuhr DIN 338 Norm für kurze Spiralbohrer Stabilität und Präzision bei drehenden Maschinen Die verkürzte Bauform reduziert die Auskraglänge und minimiert so Vibrationen und Verbiegen während des Bohrens. Dadurch entsteht eine höhere Stabilität, die besonders bei mittelgroßen Durchmessern spürbar ist. Der Einsatz einer Handbohrmaschine oder einer stationären Bohrmaschine wird durch die kompakte Länge erleichtert, was saubere Bohrbilder und verbesserte Rundlaufwerte zur Folge hat. Für Anwender bedeutet das weniger Nacharbeit und präzisere Passungen. Effizienz durch geschliffene HSS‑Geometrie und optimierten Spitzenwinkel Die geschliffene HSS‑G Geometrie liefert sehr scharfe Schneiden und eine hohe Rundlaufgenauigkeit. In Kombination mit dem 135° Spitzenwinkel dringt der Bohrer leichter in harte Materialien ein und reduziert das Ausbrechen an der Austrittskante. Technisch bewirkt das bis zu 40 % schnelleres Bohren bei gleichzeitig 50 % geringerer Anpresskraft gegenüber herkömmlichen HSS‑Bohrern, was die Produktivität in Werkstatt und Produktion erhöht. Vielfältige Einsatzgebiete und Praktische Hinweise Der Bohrer eignet sich für legierte und unlegierte Stähle, Gusseisen, Sintereisen, Temperguss, Nichteisenmetalle und Hartkunststoffe. Als Vertreter des Standard‑Bereichs ist er ideal für Werkstatt‑ und Montagearbeiten sowie für anspruchsvolle DIY‑Projekte. Bei hoher Präzision empfiehlt sich zuvor ein Zentrierbohrer, um ein Wandern des Bohrers zu vermeiden. Kühlung bei zähen Werkstoffen verlängert die Standzeit und sorgt für konstant gute Ergebnisse. Handhabung, Sicherheit und Lebensdauer Die geschliffene Herstellung verlangt umsichtiges Handling: Plötzliche Biegung soll vermieden werden, da geschliffene Werkzeuge spröder reagieren können. Für lange Standzeiten sind kontrollierte Schnittgeschwindigkeit, ausreichende Kühlung und eine stabile Werkzeugaufnahme empfehlenswert. Die Kombination aus kurzer Ausführung und geschliffener Spirale führt zu saubereren Bohrlöchern und reduziert Nacharbeit in der Fertigung. Kaufen Sie den Spiralbohrer von MetavCUT über Metav Werkzeuge und profitieren Sie von präziser Geometrie und robuster Anwendung; bei technischen Fragen erreichen Sie uns per eMail info@metav-werkzeuge.com oder Telefon +49 2822 7131930 Produktmerkmale Artikelnummer: 450875-FDA Marke: MetavCUT Bezeichnung: Spiralbohrer Serie: Standard Line Typ: Typ N Norm: DIN 338 Daten Durchmesser: 8,75 mm Gesamtlänge: 125 mm Spirallänge: 81 mm Spitzenwinkel: 135° Verpackungseinheit: 5 Besonderheiten Material: HSS-G — Schnellarbeitsstahl, geschliffen Schaftausführung: geschliffen — volle Schaftbearbeitung für hohen Rundlauf Ausführung: kurz — reduzierte Auskraglänge für erhöhte Stabilität Einsatzgebiet: legierter und unlegierter Stahl, Guss, Nichteisenmetalle, Hartkunststoff Spirallänge 81 mm — unterstützt sichere Spanabfuhr DIN 338 — Norm für kurze Spiralbohrer mit Zylinderschaft Typ N — Normalspirale, klassisch für Metallbearbeitung Farbe: blank — helle, glänzende Oberfläche Geeignet für: Handbohrmaschine und stationäre Bohrmaschinen FAQ Wie ist der Spiralbohrer für harte Werkstoffe ausgelegt? Der Spiralbohrer von MetavCUT ist mit HSS‑G geschliffen und einem 135° Spitzenwinkel ausgestattet, wodurch er sich besonders für harte Werkstoffe wie legierten Stahl und Gusseisen eignet und saubere Bohrlöcher erzeugt. Welche Maschinen sind für den Einsatz geeignet? Die kurze Ausführung wurde für den Einsatz an Handbohrmaschinen und stationären Bohrmaschinen entwickelt; bei Verwendung an mobilen Geräten sorgt die reduzierte Auskraglänge für mehr Stabilität und geringeres Verbiegen. Welche Vorteile bietet die geschliffene Ausführung gegenüber gewalzten Bohrern? Geschliffene Bohrer liefern schärfere Kanten und höhere Rundlaufgenauigkeit, was zu präziseren Bohrungen führt. Der Spiralbohrer MetavCUT als HSS‑G bietet diese Vorteile, verlangt jedoch schonendere Handhabung und Kühlung. Gibt es Empfehlungen zur Spanabfuhr und Kühlung? Dank der Spirallänge von 81 mm ist die Spanabfuhr verbessert; bei zähen oder dicken Werkstoffen empfiehlt sich zusätzliche Kühlung, um Werkzeugverschleiß zu reduzieren. Welche Norm und Typenbezeichnung hat der Bohrer? Der Bohrer entspricht der DIN 338 und wird als Typ N geführt, die Norm beschreibt kurze Spiralbohrer mit Zylinderschaft und die Typenbezeichnung steht für die Normalspirale für Metall.
8.7mm HSS-G Twist Drill DIN 338 ,short, bright finished, Type N - MetavCUT
Twist Drill — Type N Short HSS‑G, 8.7 mm, 135°, Bright Finished, DIN 338 The Twist Drill is a short Type N HSS‑G drill designed for precision metalworking in Drilling Machines, offering high stability and clean holes for demanding industrial applications. Short HSS‑G design for higher stability 8.7 mm diameter for precision metal drilling 135° point for hard materials like stainless steel Fully ground shank for high runout accuracy DIN 338 standard for consistent quality Improved stability and faster cutting for metalworking Short design increases rigidity: the short Twist Drill reduces overhang and resists bending, which improves positional accuracy during drilling. The HSS‑G (ground High Speed Steel) geometry enables significantly faster material removal — the manufacturer information cites up to 40% faster drilling with 50% less feed force compared with conventional HSS drills — which directly translates into shorter cycle times and lower operator effort when working with steels and other tough metals. Tip geometry tailored for harder materials A 135° point angle is specified to ease entry into hardened surfaces and to reduce chipping when drilling stainless and alloyed steels. For non‑specialists: a larger point angle flattens the tip, spreading cutting forces and reducing the tendency for the drill to "grab", so holes start cleaner and tool life improves under correct cooling and feed. The drill conforms to the Type N normal spiral profile, making it particularly suitable for metal applications rather than soft woods. Precise shank and manufacturing quality for consistent results The fully ground shank and ground flute geometry produce high concentricity and sharp cutting edges. Grinding (HSS‑G) rather than roll‑forming creates very sharp cutting lips and excellent roundness, which yields cleaner holes and better dimensional accuracy. Users should note that ground drills can be more brittle than rolled types and therefore benefit from using appropriate coolant and secure clamping in the machine. Intended applications and user recommendations Designed primarily as a Drill for Metal, this short Twist Drill excels in workshop and production environments where repeatable accuracy is required: toolrooms, maintenance departments and metal fabrication shops. The 8.7 mm size and 125 mm overall length make it well suited to standard drilling tasks on lathes and drilling machines, especially when drilling in alloyed or unalloyed steel, cast materials and hard plastics. For novice users, using moderate feed and coolant will extend tool life and maintain hole quality. For precision metalwork, choose the MetavCUT short HSS‑G Twist Drill — METAV Werkzeuge provides expert advice and ordering support: eMail info@metav-werkzeuge.com · Phone +49 2822 7131930 · WhatsApp +49 170 2837271 Designation: Twist Drill Brand: MetavCUT SKU: 45087-FDA Diameter: 8.7 mm Spiral length: 81 mm Total length: 125 mm Point angle: 135° Type: Type N Execution: short Finish / Colour: bright finished Shank execution: fully ground Material: HSS-G Standard: DIN 338 Application: Drills for metal For drilling machine: Drilling Machine Model series: Standard Line Packaging unit: 5 Manufacturer: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What materials is the MetavCUT Twist Drill Type N suitable for? The MetavCUT Twist Drill Type N is intended primarily for metalworking; it is suitable for alloyed and unalloyed steels, cast steel, cast iron, sintered iron, temper castings, non‑ferrous metals and hard plastics. The short HSS‑G geometry supports precise drilling in harder materials when used with suitable coolant and machine setup. How does the 135° point angle affect drilling performance with the MetavCUT Twist Drill? A 135° point angle on the MetavCUT Twist Drill reduces initial penetration forces and improves centring on hard materials; this larger angle shortens the effective cutting time and helps prevent chipping at the entry, provided the drill is used with appropriate feed and cooling. For what is a Twist Drill mainly used? A Twist Drill is most commonly applied to the machining of high‑strength materials and larger hole diameters. It is easy to regrind and withstands higher loads, making it suitable for demanding metal drilling tasks. Which three drill types are there? There are three main drill families: Metal drills, Wood drills and Masonry/Concrete drills. The MetavCUT Twist Drill belongs to the metal drill category and is optimised for that purpose. Why are Twist Drills sharpened (pointed)? Pointing the tip reduces the cross‑cut at the drill’s tip, which lowers friction and consequently the required feed force; this also improves the drill’s ability to self‑centre in the workpiece for cleaner starts. Can a Twist Drill be used for drilling wood? A metal Twist Drill can be used in wood, but guidance and finish are typically inferior to a dedicated wood bit. Metal drills are easier to resharpen and have lower self‑feed, so they are usable in a pinch but do not give as clean results as wood‑specific bits. At which depths is the Twist Drill most used? Solid drilling is commonly executed with a Twist Drill. For diameters up to 20 mm and depths up to 100 mm, the Twist Drill is the most frequently used tool. Is HSS or HSSE better? The general belief that HSSE is always superior to HSS is incorrect. When choosing between HSS and HSSE, evaluate whether the specific working conditions justify the higher cost of HSSE material.
8.8mm HSS-G Twist Drill DIN 338 ,short, bright finished, Type N - MetavCUT
Twist Drill — Short HSS-G, Ø 8.8 mm, 135°, Type N, Bright Finished, DIN 338 A short Twist Drill Type N for Drilling Machine use, designed for precise metal drilling in demanding industrial and workshop applications. Short design for higher drilling stability HSS-G ground geometry for clean, precise holes 135° tip for hard and stainless materials Fully ground shank for excellent concentricity Conforms to DIN 338 for reliable interchangeability Faster, more reliable metal drilling for tough materials The short HSS-G construction delivers a direct benefit: significantly reduced tendency to bend or whip during use, which translates into more precise holes and longer tool life under proper conditions. The 135° tip angle is optimised for harder metals and stainless steels, shortening the pilot time and improving centring on difficult surfaces. As a Type N normal-spiral geometry, this design balances chip evacuation and cutting action for typical metalworking tasks while allowing stable performance on stationary and mobile machines. Stability and handling that improve machining results A reduced overhang and the shortened overall length mean less vibration and better runout behaviour on the spindle; this yields cleaner hole edges and reduces rework. The fully ground shank guarantees improved concentricity in the chuck, so tolerances remain tight even during series production. With a diameter of 8.8 mm, a spiral length of 81 mm and an overall length of 125 mm, the tool is tailored for tasks where a compact, rigid drill bit is required to maintain accuracy in metals such as alloyed and unalloyed steels, cast steel and non-ferrous metals. Who benefits and how to choose the right drill Workshop professionals, toolmakers and maintenance technicians gain most from a short, ground HSS tool when precision and repeatability matter. The combination of HSS-G material and the short format reduces the required feed force and can increase drilling speed in appropriate conditions. For applications involving Sintereisen or Temperguss, the recommended approach is to use cutting fluid and moderate cutting parameters to exploit the drill’s performance without risking premature wear. Understanding the key specifications and safe use DIN 338 classifies short twist drills with cylindrical shank made from high-speed steel; in this case the designation indicates a ground geometry (HSS-G), produced by grinding rather than rolling. Ground drills typically achieve sharper cutting edges and higher runout precision, but they require careful handling because they can be more brittle than rolled variants. For best results, use appropriate coolant, clamp the tool securely, and keep overhangs minimal. These measures reduce heat and extend service life while ensuring consistent hole quality. Sustainability, service and after-sales support MetavCUT manufactures this short twist drill to industrial standards and METAV Werkzeuge as the vendor provides comprehensive technical consultation. If there is any uncertainty about material suitability, machining parameters, or alternative tool geometries, METAV Werkzeuge offers expert guidance and tailored recommendations to match specific workshop requirements. For precision metalworking choose the MetavCUT short HSS-G Twist Drill Type N for improved stability and hole quality — METAV Werkzeuge provides professional consultation at info@metav-werkzeuge.com or +49 2822 7131930 and via WhatsApp at +49 170 2837271 Designation: Twist Drill Marke: MetavCUT SKU: 45088-FDA Type: Typ N Diameter: 8.8 mm Spiral length: 81 mm Overall length: 125 mm Point angle: 135° Material: HSS-G (ground high-speed steel) Finish / Colour: Bright finished Shank execution: Fully ground Execution: Short Standard: DIN 338 For use in: Drilling Machine Application: Drills for metal Model series: Standard Line Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What is the Twist Drill used for and which materials is it suited to? The MetavCUT Twist Drill Type N is primarily used for metalworking; it is especially suitable for alloyed and unalloyed steel, cast steel, gusseisen and other hard materials. Its short, ground HSS construction provides improved stability and cleaner holes when used with appropriate machine settings and coolant. How does the short format of this Twist Drill affect drilling performance? A short design reduces the overhang and increases stiffness, which lowers vibration and improves concentricity. For the MetavCUT short Twist Drill this means better hole quality and the ability to operate at higher effective cutting speeds with lower feed force compared to longer equivalents. For what is a Twist Drill mainly used? A Twist Drill is mainly applied in the machining of high-strength workpieces and larger drill diameters. Its geometry is relatively easy to regrind and it withstands higher loads, making it suitable for demanding metalworking tasks. Which three drill types exist? The three primary drill categories are metal drills, wood drills and stone/concrete drills. Why are Twist Drills pointed? Pointing reduces the cross-edge at the tip of the Twist Drill, which significantly lowers friction and thus requires less feed force. At the same time the pointed geometry improves centring in the workpiece for more accurate drilling. Can a Twist Drill be used to drill wood? A metal Twist Drill such as the MetavCUT HSS-G can be used in wood, but it offers poorer guidance and a less clean finish than a dedicated wood drill. It is easier to resharpen and has less self-feeding tendency than specialised wood drills. For which drilling depths is the Twist Drill the most used tool? Solid drilling is commonly performed with Twist Drills. For diameters up to 20 mm and drilling depths up to 100 mm, the Twist Drill is the most frequently used tool. What is better, HSS or HSSE? The common assumption that HSSE steels are inherently superior to standard HSS is not universally correct. The decision should be based on the specific working conditions and whether the performance benefits justify the higher acquisition cost.
8.9mm HSS-G Twist Drill DIN 338 ,short, bright finished, Type N - MetavCUT
Twist Drill Short Type N 8.9 mm | 135° | HSS-G | Bright Finished | DIN 338 The Twist Drill Short Type N is a precision metalworking drill for Drilling Machines, designed for stable and accurate machining of hard materials. Short design for higher stability 135° point angle for hard materials HSS‑G fully ground for precise holes Complies with DIN 338 for short drills Suitable for use in Drilling Machine applications Durable HSS‑G construction for reliable machining Equipped with HSS‑G material, this Twist Drill delivers consistent cutting performance when working with alloyed and unalloyed steels. The fully ground geometry produces sharp cutting edges and high concentricity, which results in clean, burr‑reduced holes and extended tool life under correct cooling. Because the flute geometry is produced by CNC grinding rather than rolling, users benefit from superior roundness and repeatable accuracy that is particularly useful in demanding metalworking environments. Short overall length for enhanced stability and accuracy Thanks to its Short Design, the drill offers reduced overhang from the chuck, lowering the tendency to deflect and improving concentricity when drilling in tougher materials. This results in higher feed control and better hole quality, especially on bench and floor Drilling Machines. When precision counts, the shorter projection enables operators to apply lower lateral forces and maintain tighter tolerances, making the tool ideal for repetitive, high‑precision metalworking tasks. Optimised geometry for hard materials and faster drilling With a 135° Point Angle, the Twist Drill penetrates harder workpieces such as stainless steel more efficiently than standard angles, reducing the initial skidding and improving centring. The ground cutting lips and polished flutes support faster chip evacuation and allow up to 40% quicker drilling rates under suitable conditions, while requiring significantly lower feed force compared with conventional HSS drills. This geometry is particularly effective for applications where reduced entry burr and consistent hole form are priorities. Conformance, application and user guidance Manufactured to DIN 338, this Short Twist Drill Type N is specified for metalworking tasks on rotating stationary or portable machines. It is intended primarily for drilling metallic materials including cast iron, sintered iron, non‑ferrous metals and hard plastics, and is not optimised for very soft timbers. For best results, use appropriate cutting speed, steady coolant supply and a stable clamping setup to exploit the drill’s high concentricity and edge sharpness. Strong recommendation: Choose MetavCUT Twist Drill for demanding metal drilling tasks and contact METAV Werkzeuge for expert technical support and ordering assistance — 📧 info@metav-werkzeuge.com ☎️ +49 2822 7131930 ✔️ WhatsApp +49 170 2837271 Technical information Designation: Twist Drill Marke: MetavCUT SKU: 45089-FDA Diameter: 8.9 mm Overall Length: 125 mm Spiral Length: 81 mm Point Angle: 135° Type: Type N Execution: short Shank Execution: fully ground Material: HSS-G Standard: DIN 338 Colour: bright finished For Drilling Machine: Drilling Machine Application: Drills for metal Model Series: Standard Line Packaging Unit: 5 Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What is the Twist Drill Short Type N best used for? The MetavCUT Twist Drill Short Type N is primarily used for machining metal; it excels in drilling alloyed and unalloyed steel, cast materials and harder plastics thanks to its robust HSS‑G construction and shortened geometry that improves stability. Can the MetavCUT Twist Drill be used in a hand drill or only in a Drilling Machine? The Twist Drill is designed for Drilling Machine applications to achieve optimal stability and concentricity, though it may be used in heavy‑duty hand drills with appropriate clamping and reduced projection; for precise industrial tasks a stationary Drilling Machine is recommended. What are Twist Drills used for? Twist Drills are mainly applied in the machining of high‑strength materials and large drill diameters; their grindable form allows straightforward re‑sharpening and they withstand greater loads, making them suitable for demanding metalwork. Which three drill types exist? The common drill types are Metal Drill, Wood Drill and Stone/Concrete Drill. Why are Twist Drills pointed? Pointing reduces the cross‑cut at the tip, significantly lowering friction; by re‑pointing the tip the required feed force decreases and the drill centres better in the workpiece. Can you drill wood with this Twist Drill? A Metal Drill like the MetavCUT Twist Drill can be used in wood, but guidance and finish are inferior compared with dedicated Wood Drills; however, metal drills are easier to re‑sharpen and show less self‑pulling action. For which depths is the Twist Drill most used? Twist Drills are the standard tool for through drilling; they are most commonly used for diameters up to 20 mm and drilling depths up to 100 mm. Is HSS or HSSE better? The assumption that HSSE is always superior to HSS is incorrect; selection should depend on working conditions and whether the higher cost of HSSE is justified by specific application demands.
8mm HSS-G Twist Drill DIN 338 ,short, bright finished, Type N - MetavCUT
Twist Drill by MetavCUT — Type N short, Ø 8 mm, 135° point angle, Bright finished, HSS‑G, DIN 338 The Twist Drill Type N short is a compact HSS‑G drill bit designed for precise metalworking tasks in hand and stationary drilling machines. MetavCUT Twist Drill Type N Ø8 mm Short design for greater stability 135° point angle for hard metals HSS‑G fully ground for precise holes DIN 338 compliant for industrial use Faster, more stable drilling in demanding metalwork Dank der short design reduziert dieser Twist Drill das Auskragen aus dem Bohrfutter und minimiert somit Vibrationen und Verbiegen. Die verringerte Auskraglänge führt zu höherer Stability und damit zu gleichmäßigeren, maßhaltigen Bohrlöchern. Als Folge werden Bearbeitungszeiten verkürzt und die Anforderungen an die Werkzeugspannung im Alltag verringert, was besonders bei wiederholten Serienbohrungen spürbare Produktivitätsvorteile liefert. Sharp, ground geometry for clean, precise holes Die HSS‑G Ausführung mit CNC‑geschliffener Spirale sorgt für sehr scharfe Schneidkanten und hohen Rundlauf. Im Vergleich zu gewalzten Bohrern ermöglicht der Schleifprozess sauberere Spanabfuhr und glattere Bohrflächen, was die Nachbearbeitung minimiert. Diese präzise Geometrie ist besonders vorteilhaft beim Bohren in legierte und unlegierte Stähle, Gusswerkstoffe sowie Hartkunststoffe. Engineered for metals and professional workshop use Dieser Twist Drill des Typs Type N ist nach DIN 338 klassifiziert und wurde primär für Metallbearbeitung konzipiert. Er eignet sich für Temperguss, Gusseisen, Sintereisen, Nichteisenmetalle und legierte Stähle. Für Handwerker, Instandhalter und Metallwerkstätten bedeutet das: ein universelles, robustes Werkzeug für den täglichen Einsatz bei stationären oder mobilen Bohrmaschinen. Practical handling tips for longer tool life Beim Einsatz empfiehlt sich Kühlung und angepasste Schnittgeschwindigkeit, um Bruchgefahr bei geschliffenen HSS‑Bohrern zu reduzieren. Die 135° point angle erleichtert das Anbohren harter Werkstoffe, da der Anbohrvorgang verkürzt wird und die Spitze besser zentriert. Kurze Überhänge und ein sauber gespanntes Werkstück minimieren Feed‑Kräfte und erhöhen die Standzeit des Bohrers. Strong recommendation: Choose the MetavCUT short Twist Drill for precise, high‑stability metal drilling — for personal advice and technical support contact METAV Werkzeuge via info@metav-werkzeuge.com, phone +49 2822 7131930 or WhatsApp +49 170 2837271 Technical data Designation: Twist Drill Brand: MetavCUT SKU: 45080-FDA Diameter: 8 mm Overall length: 117 mm Spiral length: 75 mm Point angle: 135° Type: Type N Execution: short Shank: fully ground Material: HSS‑G Surface / Colour: Bright finished Standard: DIN 338 For: Drilling Machine Model series: Standard Line Manufacturer: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What is the main use of the Twist Drill and for which materials is it suitable? The MetavCUT Twist Drill Type N short is primarily used for drilling in metal; it is designed for high‑strength materials and larger diameters, offering good performance in alloyed and unalloyed steel, cast steel, cast iron and hard plastics. Which three drill types are commonly distinguished? Common drill categories are metal drill bits, wood drill bits and stone/concrete drill bits, with the MetavCUT Twist Drill belonging to the metal drill bit group. Why are twist drills split (point relieved)? The splitting reduces the cross‑cut at the tip, which lowers friction and requires less feed force; additionally, the modified tip improves centring in the workpiece. Can a metal twist drill be used to drill wood? A metal drill bit such as the MetavCUT Twist Drill can be used in wood, but guidance and finish are inferior compared with dedicated wood bits; metal bits are easier to re‑grind and show less self‑pulling. For which drilling depths is a twist drill most commonly used? A through hole in solid material is typically made with a twist drill; for diameters up to 20 mm and drilling depths up to 100 mm, the twist drill is the most frequently used tool. Is HSS or HSSE better for drilling? A general assumption that HSSE steels are always superior to HSS is incorrect; selection should be based on specific working conditions to determine whether the higher price of HSSE is justified.
9.1mm HSS-G Twist Drill DIN 338 ,short, bright finished, Type N - MetavCUT
Der kurze Spiralbohrer von MetavCUT verbindet erhöhte Stabilität durch die kurze Ausführung mit der Präzision eines geschliffenen HSS-G Schaftes; dadurch werden saubere Bohrbilder in legierten und unlegierten Stählen erzielt. Nutzen Sie die Kombination aus schneller Bohrleistung und reduzierter Anpresskraft und bestellen Sie den Bohrer direkt über Metav Werkzeuge oder fragen Sie unsere Beratung bei Bedarf an. Spiralbohrer Typ N von MetavCUT Der Spiralbohrer in Kurzausführung ist ein HSS-G Metallbohrer für präzise Bohrungen in Stahl und Gusseisen. Kurze Ausführung für höhere Stabilität Geschliffen (HSS-G) für scharfe Kanten Spitzenwinkel 135° für harte Werkstoffe Für Handbohrmaschine und stationäre Maschine Hohe Stabilität für präzise Metallbearbeitung Die kurze Ausführung reduziert die Auskraglänge und minimiert so Vibrationen sowie Verbiegen beim Bohren. Dadurch entsteht eine verbesserte Rundlaufgenauigkeit, die sich besonders bei Durchmessern im Standard-Bereich positiv bemerkbar macht. Für Anwender bedeutet das weniger Nacharbeit und sauberere Passungen bei Bohrungen in Stahl, Gusseisen oder Temperguss. Effizienz durch geschliffene HSS-Geometrie Der geschliffene HSS-G Schaft sorgt für sehr scharfe Schneidkanten und einen konstanten Spanabfluss, was die Bohrgeschwindigkeit erhöht und die notwendige Anpresskraft reduziert. In der Praxis führt das zu einer bis zu 40 % schnelleren Bearbeitung gegenüber konventionellen HSS-Ausführungen und erlaubt ein wirtschaftliches Arbeiten bei mittleren Serien und Einzelteilen. Geeignete Einsatzzwecke und Zielgruppe Dieser Kurzspiralbohrer ist ausgelegt für die Metallbearbeitung an Werkbank und in der leichten Werkstattproduktion. Er eignet sich für Handwerk und Industrie, insbesondere für Anwender, die stabile, präzise Bohrungen in legierten und unlegierten Stählen benötigen. Die Kombination aus kurzer Bauart und Typ N Normalspirale macht den Bohrer vielseitig einsetzbar. Handhabung, Kühlung und Sicherheitshinweise Geschliffene Kurzbohrer zeigen eine sehr gute Schnittwirkung, können aber bei unsachgemäßer Nutzung spröde reagieren. Bei der Bearbeitung harter Werkstoffe empfiehlt sich eine ausreichende Kühlung und das Anpunkten mit einem Zentrierbohrer bei hohen Anforderungen an Präzision. Die Nutzung an stationären Maschinen verbessert die Standzeit und minimiert Bruchrisiken. Empfehlung: Den MetavCUT HSS-G Kurzspiralbohrer als Standard Line für präzise Metallbohrungen über Metav Werkzeuge beziehen; bei Fragen per eMail info@metav-werkzeuge.com oder Telefon +49 2822 7131930 erreichbar Produktmerkmale Artikelnummer: 45091-FDA Marke: MetavCUT Serie: Standard Line Fakten Durchmesser: 9,1 mm Gesamtlänge: 125 mm Spirallänge: 81 mm Spitzenwinkel: 135° Verpackungseinheit: 5 Besonderheiten Material: HSS-G (Schnellarbeitsstahl) Schaftausführung: Geschliffen (CNC-Schliff) Norm: DIN 338 (Kurzspiralbohrer) Typ: Typ N (Normalspirale) Ausführung: Kurz Farbe: blank (Bright finished) Verwendung: Bohrer für Metall Für Bohrmaschine: Handbohrmaschine Hersteller: MetavCUT Bezeichnung: Spiralbohrer Modellserie: Standard Line SKU: 45091-FDA FAQ Für welche Materialien eignet sich der Bohrer am besten? Der MetavCUT Spiralbohrer Typ N in HSS-G Ausführung eignet sich vor allem für legierte und unlegierte Stähle, Gusseisen sowie harte Nichteisenmetalle; die geschliffene Geometrie gewährleistet saubere Bohrungen. Ist der Bohrer für Handgeführte Geräte geeignet? Ja, der Spiralbohrer wurde für den Einsatz an Handbohrmaschine und stationären Maschinen konzipiert; bei besonders kleinen Durchmessern ist jedoch auf Stabilität und Rundlauf zu achten. Welchen Vorteil bringt der Spitzenwinkel von 135°? Der 135° Spitzenwinkel reduziert das Anlaufen beim Anbohren harter Werkstoffe und erleichtert das Eindringen in Edelstahl oder gehärtete Stähle, was bei dem MetavCUT HSS-G Bohrer deutlich spürbar ist. Wie wirkt sich die geschliffene Schaftausführung auf die Standzeit aus? Die geschliffene Ausführung sorgt für hohe Präzision und scharfe Schnittkanten, wodurch saubere Bohrbilder entstehen; bei fehlender Kühlung kann die Sprödigkeit die Bruchgefahr erhöhen. Welche Norm beschreibt diesen Bohrertyp? Die Herstellung und Abmessung orientiert sich an DIN 338, die kurze Spiralbohrer mit Zylinderschaft klassifiziert; der MetavCUT Spiralbohrer entspricht dieser Norm (SKU 45091-FDA).
9.25mm HSS-G Twist Drill DIN 338 ,short, bright finished, Type N - MetavCUT
Twist Drill Type N short bright finished (Ø 9.25 mm, 135°, HSS‑G, DIN 338) by MetavCUT The Twist Drill Type N short is a precision metalworking drill designed for Drilling Machines and manual drilling, offering a compact, stable design for hard materials. Short design for high stability and precision Fully ground shank for accurate concentricity 135° point angle for drilling hard steels HSS‑G material: sharp, precise holes in metal Conforms to DIN 338 for short twist drills Durable cutting geometry for demanding metalwork The HSS‑G material and CNC grinding process give this Twist Drill a very sharp cutting edge and high runout accuracy, resulting in clean, burr‑reduced holes when used on metal. Professionals benefit from the improved hole quality and consistency, since the ground flute geometry is optimized for metals such as alloyed and unalloyed steel, cast steel, and non‑ferrous alloys. This results in fewer reworks and better component fit in assemblies. Short length increases rigidity and speeds up working steps Thanks to the short spiral length and compact overall profile, bending and chatter are significantly reduced, which improves hole precision in demanding operations. The shorter overhang also enables up to 40% faster drilling with about 50% less feed force compared with conventional HSS drills, making it particularly effective for tight‑tolerance metalworking and applications on stationary or portable drilling machines. Targeted use: where best results are achieved This Twist Drill Type N short by MetavCUT is aimed at machinists, toolrooms and maintenance workshops that require reproducible, high‑quality holes in metallic components. It is especially suited to operations on Drilling Machines and other rotating tools where stability matters. Its 135° point angle helps reduce entry burrs and improves centring when working with harder materials such as stainless steel. Standard compliance and handling considerations Manufactured to DIN 338 and delivered as a fully ground (HSS‑G) short drill, this tool provides tight tolerances and repeatable performance. Users should be aware that ground HSS drills can be more brittle than rolled variants and therefore benefit from adequate coolant and moderate cutting parameters. Periodic resharpening restores the precise geometry; when regrinding, keep the original point angle to preserve centring behavior. Strong recommendation: For precision metal drilling choose the MetavCUT Twist Drill Type N short and contact METAV Werkzeuge for personalised technical advice via email info@metav-werkzeuge.com, phone +49 2822 7131930 or WhatsApp +49 170 2837271 Technical Data Designation: Twist Drill Brand: MetavCUT SKU: 450925-FDA Diameter: 9.25 mm Point angle: 135° Type: Type N Execution: short Finish/Color: bright finished Shank execution: fully ground Material: HSS‑G Spiral length: 81 mm Overall length: 125 mm For machine: Drilling Machine Model series: Standard Line Application: Drills for metal Standard: DIN 338 Manufacturer: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What is the Twist Drill Type N short best used for? The MetavCUT Twist Drill Type N short is primarily used for machining high‑strength materials and larger diameters in metalworking; its design and ground geometry make it easy to resharpen and capable of withstanding greater loads during drilling. Which three drill types exist? Common categories are metal drills (like the MetavCUT Twist Drill Type N), wood drills, and stone/concrete drills; each is optimised in geometry and material for its specific substrate. Why are twist drills pointed (resharpened)? The point sharpening reduces the cross‑cut at the tip of the Twist Drill Type N short, lowering friction and thus the required feed forces while improving centring of the drill in the workpiece. Can a metal Twist Drill be used to drill wood? A metal drill such as the MetavCUT Twist Drill Type N can be used in wood, but guidance and finish are inferior to a dedicated wood drill; however, metal drills are easier to resharpen and show less self‑feeding tendency. At which drilling depths is the Twist Drill most commonly used? A through hole in solid stock is typically produced with a Twist Drill; for diameters up to about 20 mm and drilling depths up to around 100 mm, the Twist Drill Type N short and related designs are the most commonly used tooling. Is HSS or HSSE better for my application? The general belief that HSSE is always superior to HSS is not universally correct; assess working conditions and cost‑benefit to decide whether the higher price of HSSE is justified for your specific use with tools such as the MetavCUT Twist Drill Type N.
9.2mm HSS-G Twist Drill DIN 338 ,short, bright finished, Type N - MetavCUT
Twist Drill — Short HSS‑G Type N, Ø 9.2 mm, 135°, Bright Finished The Twist Drill is a short Type N drill for precise metalworking that delivers high stability and fast penetration in demanding applications with drilling machines. Short design for greater stability and precision HSS‑G, fully ground geometry for fast cutting 135° tip angle optimised for harder materials Conforms to DIN 338 for short twist drills Bright finished shank with 125 mm overall length Precision performance for metalworking professionals The Twist Drill from MetavCUT combines a short execution with a fully ground HSS‑G geometry, enabling up to 40% faster drilling with significantly reduced feed force. This configuration reduces vibration and bending, so drilling holes remain accurate even in tougher alloys. The 135° tip angle is specifically helpful when working with stainless steel and other hard materials, as it shortens pilot time and improves centring. For workshops requiring repeatable, clean holes, this tool delivers measurable efficiency gains. Short length for greater stability and cleaner holes A reduced overall length means less overhang from the chuck and therefore less tendency to wander. The shorter Spiral Length and compact design provide superior stability and allow higher cutting speeds with better runout behaviour. Because the cutting lips are produced by CNC grinding (HSS‑G), edge sharpness and concentricity are improved, resulting in cleaner holes and longer tool life under appropriate cutting conditions and coolant use. This makes the drill particularly suitable for precision machining tasks. Suited applications and target users Intended primarily for metalworking, the MetavCUT Twist Drill is aimed at professional workshops, maintenance teams and fabrication shops that operate drilling machines and stationary machine tools. The drill is effective on alloyed and unalloyed steels, cast steel, cast iron, sintered iron, malleable iron, non‑ferrous metals and hard plastics. Its short, rigid design benefits tasks where hole quality and repeatability matter most, for example component manufacturing, toolrooms and industrial maintenance. Practical details and handling recommendations Key handling advantages include the bright finished surface for corrosion resistance and easy chip evacuation, plus a fully ground shank that ensures precise clamping and minimal runout. The drill’s overall length is 125 mm with a spiral length of 81 mm and a diameter of 9.2 mm, dimensions that balance accessibility and rigidity. For best results in hard materials, use appropriate cutting fluid and moderate feed to exploit the drill’s geometry; avoid excessive pecking that could induce thermal stress. Regular inspection and resharpening preserve accuracy and extend service life. Strong recommendation: Choose the MetavCUT short HSS‑G Twist Drill for demanding metal drilling tasks and contact METAV Werkzeuge for expert technical advice — 📧 info@metav-werkzeuge.com / ☎️ +49 2822 7131930 / ✔️ WhatsApp +49 170 2837271 Technical Data Designation: Twist Drill Brand: MetavCUT SKU: 45092-FDA Diameter: 9.2 mm Spiral Length: 81 mm Overall Length: 125 mm Tip Angle: 135° Type: Type N Execution: short Shaft Finish: fully ground Material: HSS-G Colour: bright finished Application: Drills for metal For Drilling Machine: Drilling Machine Model Series: Standard Line Norm: DIN 338 Manufacturer: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What materials is the MetavCUT Twist Drill best suited for? The MetavCUT Twist Drill (Type N) is tailored for metalworking and performs best in alloyed and unalloyed steels, cast steel, cast iron, sintered iron, malleable iron, non‑ferrous metals and hard plastics; its 135° tip and HSS‑G grind enable controlled entry and efficient chip formation in harder materials. Is the MetavCUT Twist Drill suitable for handheld use or only for machine tools? Although the MetavCUT Twist Drill is primarily intended for use on rotating machine tools for optimal rigidity and accuracy, it can be used in drilling machines where the toolholder provides secure clamping; for handheld operations ensure minimal overhang and steady feed to avoid breakage. What is a Twist Drill used for? A Twist Drill is mainly applied to machining high‑strength materials and larger drill diameters; its geometry allows easy resharpening and it withstands greater loads, making it suitable for demanding metalworking tasks. Which three drill types exist? The three common drill types are metal drills, wood drills and stone/concrete drills.
9.3mm HSS-G Twist Drill DIN 338 ,short, bright finished, Type N - MetavCUT
Twist Drill — Type N Short, Ø 9.3 mm, 135° Tip, HSS‑G, Bright Finished, Fully Ground Shank, DIN 338 The Twist Drill Type N short is a precision HSS‑G metalworking drill designed for use with a Drilling Machine and optimised for stable, accurate holes in hard materials. Short Type N design for superior stability 135° tip angle for hard materials like stainless steel HSS‑G Material for sharp, precise metal drilling Fully ground shank for high runout accuracy Conforms to DIN 338 for standardised quality Maximum precision and faster drilling for demanding metalwork The Twist Drill delivers high Precision through its HSS‑G construction and fully ground geometry, producing clean holes and excellent roundness. Shorter Spiral Length reduces overhang and improves Stability, which in practice means less vibration and a reduced risk of breakage when working with tough materials. For users requiring reliable performance on alloys and tempered steels, this design yields up to 40% faster drilling and typically needs 50% less feed force compared with conventional HSS drills, translating into measurable time savings on repetitive tasks. Robust material and geometry tailored for hard materials Constructed from HSS‑G and finished bright, the drill features a 135° Tip Angle that is optimised for hard and stainless steels by reducing initial entry forces and improving centring. The fully ground flutes ensure sharp cutting edges and consistent chip evacuation, while the short overall length increases rigidity. These attributes combine to provide greater tool life under appropriate cooling and steady feeds, making the tool particularly suitable for precision work on Alloys, Cast Steel and high strength components. Practical applications and recommended use Designed as a metal drill, the Tool is ideal for workshop and industrial applications including component manufacture, maintenance and toolroom operations. The short Type N configuration excels where confined setups or minimal overhang are required, for example jigging, machine‑mounted drilling and multi‑operation stations. When used with a Drilling Machine and suitable coolant, the drill produces consistently accurate holes in Cast Iron, Non‑ferrous Metals and various steels. For hand‑held drills choose appropriate clamping and low runout chucks to maintain accuracy. Who benefits and why this drill stands out Engineers, maintenance technicians and precision craftsmen benefit from the combination of DIN 338 standardisation and the grind quality of this Twist Drill. The Standard Line Series emphasises reproducible Quality and interchangeability across toolholders and setups. The short execution minimises deflection and the Type N spiral is the proven general‑purpose geometry for metalworking, balancing chip evacuation and edge strength. For production environments where hole quality and repeatability matter, this drill reduces rework and supports consistent cycle times. We recommend choosing METAVCUT Twist Drill for metalworking tasks that demand high stability and precise hole quality — for further guidance or bespoke technical advice please contact METAV Werkzeuge: 📧 info@metav-werkzeuge.com ☎️ +49 2822 7131930 ✔️ WhatsApp +49 170 2837271 Technical information Designation: Twist Drill Brand: MetavCUT SKU: 45093-FDA Diameter: 9.3 mm Spiral Length: 81 mm Overall Length: 125 mm Tip Angle: 135° Type: Type N Material: HSS‑G Finish / Colour: Bright finished Shank: Fully ground Execution: Short Standard: DIN 338 For Machine: Drilling Machine Model Series: Standard Line Application: Drills for Metal Manufacturer: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What is the Twist Drill Type N short best used for? The MetavCUT Twist Drill Type N short is primarily used for precise drilling in high‑strength and hard metals; its short design increases rigidity so it is especially suitable for drilling in Alloyed and Unalloyed Steel, Cast Iron and other tough materials under machine conditions. Which three drill types are most common? Common drill categories are Metal Drills, Wood Drills and Stone/Concrete Drills; the MetavCUT Twist Drill belongs to the Metal Drill category and is optimised for metalworking tasks. For what is a Twist Drill generally used? A Twist Drill is mainly applied to machining high‑strength materials and larger diameters; its grindable form makes repair straightforward and it withstands higher loads, making it a standard choice for demanding metal drilling operations. Why are Twist Drills sharpened at the tip? The tip grind reduces the cross‑cut at the point, lowering friction and the necessary feed forces, while improving centring of the Twist Drill in the workpiece. This leads to easier penetration and more accurate hole starts.
9.4mm HSS-G Twist Drill DIN 338 ,short, bright finished, Type N - MetavCUT
Kompakte Präzision: Der kurz ausgeführte Spiralbohrer aus HSS‑G kombiniert hohe Stabilität durch geringe Auskraglänge mit scharfer, geschliffener Geometrie und dem 135° Spitzenwinkel für harte Werkstoffe. Bestellen Sie den Bohrer direkt über Metav Werkzeuge oder fragen Sie unsere Beratung bei Bedarf an. Spiralbohrer (Kurz, HSS‑G) von MetavCUT Standard Line Der Spiralbohrer in Kurz‑Ausführung eignet sich für präzises Bohren in legierten und unlegierten Stahl sowie in Gusswerkstoffen und Hartkunststoff. Kurz‑Ausführung für hohe Stabilität beim Bohren Geschliffener HSS‑G für scharfe Kanten und Präzision Spitzenwinkel 135° optimiert für harte Werkstoffe Spirallänge 81 mm für kontrollierte Spanabfuhr Geeignet für Handbohrmaschine und stationäre Maschinen Kompakte Bauweise sorgt für mehr Präzision Die Kurz‑Ausführung reduziert die Auskraglänge und minimiert somit das Risiko von Durchbiegung und Vibrationen. Dies führt zu saubereren Bohrlöchern und gleichmäßigem Vorschub, besonders bei Bohrungen in Stahl und Guss. Anwender profitieren von besserer Wiederholgenauigkeit bei Serien und weniger Nacharbeit. Der geringere Hebelarm sorgt außerdem für eine spürbar bessere Kraftübertragung auf das Werkzeug. Geschliffene Geometrie für saubere Schnitte Ein geschliffener HSS‑Bohrer liefert sehr scharfe Schneiden und hohe Rundlaufgenauigkeit, was sich in sauberen Bohrlochkanten und engeren Toleranzen niederschlägt. Der Bohrer ermöglicht ein bis zu 40 % schnelleres Bohren und benötigt dabei 50 % weniger Anpresskraft im Vergleich zu herkömmlichen HSS‑Ausführungen, wodurch die Maschinenbelastung reduziert wird. Der 135° Spitzenwinkel erleichtert das Anbohren harter Werkstoffe und reduziert das Ausreißen beim Austritt. Für Werkstatt und Produktion: vielseitiger Einsatz Mit einem Durchmesser von 9,4 mm liegt dieses Werkzeug im Standard‑Bereich, geeignet für Werkstatt, Montage und anspruchsvolle DIY‑Projekte. Der Typ N Normalspirale ist für Metallbohrungen optimiert und nach DIN 338 klassifiziert, was die Kompatibilität mit gängigen Maschinentypen sicherstellt. Anwender sollten bei höchster Präzision ein Zentrierbohren in Erwägung ziehen, um das Wanderverhalten zu minimieren und exakte Passungen zu erzielen. Handhabungsempfehlungen für lange Werkzeugstandzeiten Bei stationärem Arbeiten und tieferen Bohrungen ist die Verwendung von Kühlschmierstoffen ratsam, um Wärmeaufbau zu vermeiden und Spananhäufungen zu reduzieren. Der geschliffene Schaft verlangt vorsichtige Handhabung bei Stoßbelastungen; deshalb empfiehlt sich der Einsatz in Spannfuttern mit guter Rundlaufgenauigkeit. Die Spirallänge von 81 mm gewährleistet eine zuverlässige Spanabfuhr bei normalen Bohrtiefen und verringert so das Verkleben in Nichteisenmetallen. Empfehlung: Den MetavCUT Standard Line Spiralbohrer in HSS‑G Kurz‑Ausführung für präzise Metallbearbeitung wählen und bei Fachfragen direkt Metav Werkzeuge kontaktieren unter info@metav-werkzeuge.com oder telefonisch +49 2822 7131930 Produktmerkmale Artikelnummer: 45094-FDA Marke: MetavCUT Serie: Standard Line Bezeichnung: Spiralbohrer SKU: 45094-FDA Zahlen Durchmesser: 9,4 mm Gesamtlänge: 125 mm Spirallänge: 81 mm Spitzenwinkel: 135° Verpackungseinheit: 5 Besonderheiten Material: HSS‑G (Geschliffen) Norm: DIN 338 (Kurzspiralbohrer mit Zylinderschaft) Schaftausführung: Geschliffen (volle Schleifung für hohe Rundlaufgenauigkeit) Typ: Typ N (Normalspirale, geeignet für Metall) Farbe: Blank (hell ausgeführt) Ausführung: Kurz (geringe Auskraglänge) Anwendung: Bohrer für Metall Für Bohrmaschine: Handbohrmaschine und stationäre Maschinen Hersteller: MetavCUT FAQ Für welche Materialien ist dieser Bohrer geeignet? Der MetavCUT Spiralbohrer in HSS‑G Kurz‑Ausführung ist ausgelegt für legierten und unlegierten Stahl, Gussstahl, Gusseisen, Sintereisen, Temperguss, Nichteisenmetalle und Hartkunststoff und liefert dort saubere Bohrbilder. Ist der geschliffene Bohrer auch für Handgebrauch geeignet? Ja, der Spiralbohrer eignet sich für Handbohrmaschine sowie für stationäre Maschinen; bei handgeführten Geräten auf festen Rundlauf und kontrollierten Vorschub achten. Wann ist Vorbohren empfehlenswert? Bei hohen Präzisionsanforderungen oder sehr tiefen Bohrungen empfiehlt sich Zentrieren oder ein kleines Vorbohren, um das Wandern zu minimieren und die Querschneide zu entlasten. Wie wirkt sich der 135° Spitzenwinkel aus? Ein 135° Spitzenwinkel reduziert das Ausbrechen beim Austritt und erleichtert das Anbohren harter Werkstoffe wie Edelstahl, wodurch das Spanverhalten verbessert wird. Welche Pflege verlängert die Standzeit? Regelmäßige Kühlung bei Metallbearbeitung, sauberes Entfernen von Spänen und spannfeste Aufnahme im Spannfutter erhöhen die Lebensdauer des geschliffenen Spiralbohrers.
9.5mm HSS-G Twist Drill DIN 338 ,short, bright finished, Type N - MetavCUT
Twist Drill — Short HSS-G Type N, 9.5 mm, 135°, Bright Finished (DIN 338) Twist Drill is a short HSS-G metalworking drill designed for precision drilling in hard materials with a 9.5 mm diameter and a 135° tip, suitable for use in drilling machines. Short design for improved stability 9.5 mm Diameter for precise holes 135° Tip for hard materials like stainless steel HSS-G Ground for sharp, accurate cutting Conforms to DIN 338 for consistent quality Precision through material and grind for cleaner holes The HSS-G construction and CNC grinding give this short Twist Drill exceptionally sharp cutting edges and high runout accuracy, resulting in clean, burr-reduced holes in metal. Because the flute geometry is produced by grinding rather than rolling, the bit achieves very fine edge definition that supports precise diameter tolerances. This makes the tool especially appropriate for applications where finished-hole quality matters and subsequent reaming or finishing should be minimised. Short length increases rigidity and drilling performance A reduced overall length and shorter cantilever improve axial stiffness and reduce deflection under load, so the short Twist Drill maintains a straighter bore when machining. The short design leads to more stable cutting conditions, which is advantageous when working with tough alloys or thin-walled components. In practice this means higher feed rates and reduced chatter, enabling more efficient cycle times on both stationary and portable drilling equipment. Optimised geometry for hard and alloyed steels With a 135° Tip and a classic Type N spiral, this Twist Drill is configured to enter hard materials smoothly while minimising initial splintering. The larger tip angle reduces the tendency to dig in and shortens lead-in time, which benefits machining of stainless steel and other demanding workpieces. The Type N normal spiral is tailored to metal drilling tasks, offering chip evacuation and consistent engagement in a wide range of ferrous and non-ferrous materials. Application focus and target users Engineers, maintenance technicians and toolroom operators who require reproducible, clean metal holes will benefit from this short Twist Drill. It is aimed at professionals needing reliable results on construction parts, machine components and jigs, where stability and precision are priorities. The bit is also suitable for use on bench drills and drilling machines where the reduced overhang improves operational safety and repeatability. We recommend the MetavCUT short Twist Drill for demanding metalworking tasks — for expert guidance and technical advice contact METAV Werkzeuge via info@metav-werkzeuge.com, phone +49 2822 7131930 or WhatsApp +49 170 2837271 Designation: Twist Drill (Short) Brand: MetavCUT SKU: 45095-FDA Diameter: 9.5 mm Tip angle: 135° Type: Type N Material: HSS-G Finish / Colour: Bright finished Shank: Fully ground Spiral length: 81 mm Overall length: 125 mm Execution: short For drilling machine: Drilling Machine (Handbohrmaschine) Norm: DIN 338 Application: Drills for metal Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What materials is the Twist Drill from MetavCUT (Type N) best suited for? The MetavCUT Twist Drill (Type N) is primarily intended for metalworking; its HSS-G grind and 135° Tip make it suitable for alloyed and unalloyed steel, cast steel, cast iron, sintered iron, malleable cast iron, non-ferrous metals and hard plastics. Can the short Twist Drill be used in portable drills and bench drilling machines? Yes, the short construction of the MetavCUT Twist Drill improves rigidity and reduces deflection, so it is particularly well suited for both portable Hand Drilling Machines and stationary drilling machines when precision and stability are required. For what is a Twist Drill used? A Twist Drill is mainly used for machining high-strength materials and larger drill diameters. Its shape is easy to sharpen and withstands higher loads. Which three drill types are there? There are three main drill types: Metal drill, Wood drill, and Stone/Concrete drill. Why are Twist Drills sharpened (pointed)? Pointing reduces the cross-cut at the tip of the Twist Drill. By sharpening, friction forces are considerably lowered, requiring less feed force and improving centring of the drill tip in the workpiece. Can a metal drill be used to drill wood? A metal drill can be used in wood, but guidance is poorer and the hole finish is less clean. Metal drills are easier to resharpen and have less self-feed compared with specialised wood drills. For which drilling depths is the Twist Drill most commonly used? Solid drilling with a Twist Drill is typical for hole diameters up to 20 mm and drilling depths up to 100 mm; within these ranges the Twist Drill is the most frequently used tool. What is better, HSS or HSSE? The common belief that HSSE steels are generally superior to standard HSS is incorrect; when choosing, assess whether your working conditions justify the higher purchase cost.
9.6mm HSS-G Twist Drill DIN 338 ,short, bright finished, Type N - MetavCUT
Kompakter Einsatz für präzise Metallbohrungen: Der kurze Spiralbohrer kombiniert HSS-G-Material und geschliffene Geometrie für hohe Stabilität und saubere Bohrbilder. Profitieren Sie von schnellerem Vorschub durch den 135° Spitzenwinkel und von der Eignung für Handbohrmaschine und stationäre Maschinen. Bestellen Sie den Bohrer bequem über Metav oder kontaktieren Sie unsere Beratung bei Bedarf. Spiralbohrer Kurzausführung von MetavCUT (HSS-G, Typ N) Der Spiralbohrer ist als kurze Ausführung für präzise Bohrungen in legierten und unlegierten Stahl sowie Gusseisen konzipiert. Kurze Auskraglänge für erhöhte Stabilität HSS-G geschliffen: scharfe Kanten, hohe Rundlaufgenauigkeit Spitzenwinkel 135° für härtere Werkstoffe Geeignet für Handbohrmaschine und stationäre Maschinen DIN 338 Normkonformität für kurze Spiralbohrer Höhere Stabilität und präzisere Ergebnisse bei Metallbohrungen Dank der kurzen Auskraglänge verringert sich die Neigung zum Verbiegen, sodass konzentrierte Bohrkräfte kontrollierter übertragen werden. Diese Bauart macht den Bohrer besonders geeignet für präzise Bohrungen in Stahl und Guss, bei denen eine saubere Kantengeometrie und ein stabiler Spanfluss entscheidend sind. Die geschliffene Ausführung sorgt für eine exakte Spiralgeometrie und ein sauberes Bohrbild. Effizienz und Anwenderkomfort durch optimierte Geometrie Die Kombination aus HSS-G-Material und einem 135° Spitzenwinkel ermöglicht ein schnelleres Eindringen in harte Werkstoffe bei gleichzeitig reduziertem Anpressdruck. Anwender profitieren von einem bis zu 40 % schnelleren Bohrfortschritt im Vergleich zu herkömmlichen HSS-Bohrern und von geringerer Ermüdung beim maschinellen Bohren. Dadurch eignen sich diese Kurzbohrer sowohl für Einzelteile als auch für kleine Serien in der Werkstatt. Passgenauigkeit für typische Metallbearbeitungsaufgaben Als Typ N Normalspirale ist der Bohrer ideal für die Bearbeitung von Stahl, Temperguss, Sintereisen, Nichteisenmetallen und härteren Kunststoffen. Für präzise Passungen empfiehlt es sich, bei hohen Anforderungen an die Maßhaltigkeit vorgängig zu zentrieren; ansonsten erlaubt die robuste Konstruktion direkten Einsatz mit Handbohrmaschine und stationären Bohrern. Die kürzere Länge begünstigt zudem den Einsatz in beengten Arbeitsbereichen. Materialqualität, Normen und Fertigungsdetails Die Fertigung als HSS-G geschliffener Kurzspiralbohrer nach DIN 338 garantiert definierte Maßtoleranzen und eine gleichbleibende Qualität. Geschliffene Spannuten führen zu scharfen Schneiden und hoher Rundlaufgenauigkeit, wobei die sprödere Eigenschaft diesen Bohrertyp für stationäre oder gut unterstützte Anwendungen prädestiniert. Für anspruchsvolle Materialien empfiehlt sich die Nutzung von Kühlschmierstoffen zur Standzeitverlängerung. MetavCUT Spiralbohrer Kurzausführung (HSS-G) empfiehlt sich für anspruchsvolle Metallarbeiten; Bestellungen und technische Rückfragen direkt an Metav: info@metav-werkzeuge.com oder Tel. +49 2822 7131930 — Präzision aus Emmerich. Produktmerkmale Artikelnummer: 45096-FDA Bezeichnung: Spiralbohrer Marke: MetavCUT Serie: Standard Line Ausführung: kurz Zahlen Durchmesser: 9,6 mm Gesamtlänge: 125 mm Spirallänge: 81 mm Spitzenwinkel: 135° Verpackungseinheit: 5 Stück Besonderheiten Material: HSS-G (Schnellarbeitsstahl, geschliffen) Norm: DIN 338 (kurze Spiralbohrer mit Zylinderschaft) Schaftausführung: geschliffen (vollständig geschliffener Schaft) Typ: Typ N (Normalspirale, geeignet für Metall) Einsatz: Bohrer für Metall, geeignet für Handbohrmaschine Farbe: blank FAQ Ist dieser Bohrer für Edelstahl geeignet? Der MetavCUT Spiralbohrer in HSS-G Ausführung und mit 135° Spitzenwinkel eignet sich für viele härtere Stähle; bei rostfreiem Edelstahl ist Kühlschmierstoff und reduzierte Vorschubgeschwindigkeit empfohlen, um Überhitzung zu vermeiden. Wie unterscheidet sich die geschliffene Ausführung von gerollten Bohrern? Geschliffene HSS-G Bohrer wie der MetavCUT Spiralbohrer bieten schärfere Kanten und bessere Rundlaufgenauigkeit, weshalb sie sauberere Bohrbilder in Metall erzeugen; sie können jedoch spröder sein und profitieren von stationärer Nutzung und Kühlung. Eignet sich der Bohrer für Handbohrmaschine-Einsätze? Ja, die kurze Auskraglänge und die robuste Geometrie machen den Bohrer gut geeignet für die Verwendung mit Handbohrmaschine sowie mit stationären Bohrmaschinen bei kontrollierter Führung. Welche Rolle spielt die DIN 338 Norm bei diesem Bohrer? Die DIN 338 Klassifikation bestätigt, dass es sich um einen kurzen Spiralbohrer mit Zylinderschaft handelt; das bedeutet definierte Länge, Schaftform und Fertigungsanforderungen, die industrielle Austauschbarkeit und Qualität sichern. Was ist die Artikelnummer und Verpackungsgröße? Die Artikelnummer lautet 45096-FDA; der Bohrer wird in Verpackungseinheiten zu 5 Stück geliefert, ideal für Werkstattbedarf und kleinere Serien.
9.75mm HSS-G Twist Drill DIN 338 ,short, bright finished, Type N - MetavCUT
Der kurze Spiralbohrer von MetavCUT verbindet hohe Stabilität, schnelle Zerspanung und normkonforme Fertigung: Die HSS-G Ausführung mit geschliffener Geometrie und 135° Spitzenwinkel ermöglicht effizientes Bohren in Stahl und Guss, während die kürzere Auskraglänge Verbiegen reduziert. Bestellen Sie den Bohrer einfach über Metav und nutzen Sie die Fachberatung bei technischen Fragen. Spiralbohrer 9,75 mm – kurzer HSS-G Metallbohrer von MetavCUT Spiralbohrer 9,75 mm in kurzer Ausführung für präzise Metallbohrungen an stationären und handgeführten Maschinen Kurz-Ausführung für hohe Stabilität HSS-G geschliffen: präzise Schneidekraft 9,75 mm Durchmesser für Standard-Metallarbeiten Spitzenwinkel 135°: ideal für harte Werkstoffe DIN 338 konform, Zylinderschaft Typ N Höhere Präzision bei harten Werkstoffen dank geschliffener HSS-Geometrie Die HSS-G Fertigung sorgt für sehr scharfe Schneidkanten und hohe Rundlaufgenauigkeit, was saubere Bohrlöcher in legierten und unlegierten Stahl ermöglicht. Durch den 135° Spitzenwinkel verringert sich die Anbohrzeit bei hartem Material, sodass die Bearbeitung kontrollierter und mit weniger Vorschubkraft erfolgt. Dieser Vorteil führt zu reproduzierbaren Ergebnissen in der Serien- und Einzelteilfertigung. Kompakte Bauweise reduziert Auslenkung und erhöht Standzeit Die kurze Gesamtlänge mit geringerer Auskraglänge verbessert die Stabilität während des Bohrens und minimiert Vibrationen sowie Verbiegen. In der Praxis bedeutet das weniger Ausschuss und gleichmäßigere Bohrbilder, besonders bei tiefen, aber nicht überlangen Bohrungen. Die robuste Konstruktion eignet sich daher sowohl für stationäre Bohrmaschinen als auch für den Einsatz mit Handbohrmaschinen bei kontrollierter Anwendung. Vielseitiger Einsatzbereich für Metall und technische Kunststoffe Die Auslegung nach DIN 338 und die Klassifikation als Typ N machen diesen Bohrer zur universellen Wahl für Stahl, Gussstahl, Gusseisen, Sintereisen, Temperguss sowie Nichteisenmetalle und Hartkunststoffe. Dank der geschliffenen Spirale werden Späne sauberer abgeführt, was insbesondere bei legierten Werkstoffen und höherer Schnittgeschwindigkeit von Vorteil ist. Die Kurz-Ausführung fördert die Standzeit bei intermittierender Kühlung. Effizienzsteigerung in Werkstatt und Produktion Der geschliffene Spiralbohrer benötigt deutlich weniger Anpresskraft und bohrt schneller als herkömmliche HSS-Werkzeuge, was die Bearbeitungszeit pro Loch reduziert und die Produktivität erhöht. Die Kombination aus 9,75 mm Durchmesser, Spirallänge 87 mm und geschliffenem Schaft ergibt ein ausgewogenes Werkzeugbild für den täglichen Einsatz. Verpackungseinheit fünf erleichtert die Vorratshaltung in der Werkstatt. Empfehlung: Für zuverlässige Metallbohrungen wählen Sie die MetavCUT Standard Line HSS-G Kurz-Ausführung – Beratung und Lieferung direkt aus Emmerich per eMail info@metav-werkzeuge.com oder Telefon +49 2822 7131930. Technische Daten Bezeichnung: Spiralbohrer Hersteller: MetavCUT Serie: Standard Line SKU: 450975-FDA Norm: DIN 338 Daten Durchmesser: 9,75 mm Gesamtlänge: 133 mm Spirallänge: 87 mm Spitzenwinkel: 135° Verpackungseinheit: 5 Besonderheiten Material: HSS-G Schaft Ausführung: geschliffen Ausführung: kurz Typ: Typ N Farbe: blank Für Bohrmaschine: Handbohrmaschine Anwendung: Bohrer für Metall FAQ Welche Materialien lassen sich mit dem Spiralbohrer bearbeiten? Der Spiralbohrer von MetavCUT Standard Line (SKU 450975-FDA) ist für legierten und unlegierten Stahl, Gussstahl, Gusseisen, Sintereisen, Temperguss sowie Nichteisenmetalle und Hartkunststoffe ausgelegt und liefert bei diesen Werkstoffen saubere Bohrbilder. Ist die kurze Ausführung für Handgebrauch geeignet? Die kurze Ausführung verbessert die Stabilität und erlaubt den Einsatz mit Handbohrmaschinen unter kontrollierten Bedingungen; für höchste Präzision empfiehlt sich jedoch die Nutzung an stationären Maschinen. Was bedeutet HSS-G geschliffen in der Praxis? HSS-G geschliffen steht für einen präzisen CNC-Schliff der Spannuten, was sehr scharfe Kanten, bessere Rundlaufgenauigkeit und schnellere Zerspanung bedeutet; bei entsprechender Kühlung ergibt das längere Standzeiten. Welchen Vorteil bringt der Spitzenwinkel 135°? Der 135° Spitzenwinkel reduziert das Anlaufen und erleichtert das Bohren in härteren Werkstoffen wie Edelstahl, da der Bohrer kontrollierter einsetzt und weniger axialen Vorschub erfordert. Wie viele Bohrer sind pro Verpackungseinheit enthalten? Die Verpackungseinheit enthält fünf Bohrer, ideal zur Auffüllung des Werkzeugbestands in Werkstätten und Produktionsumgebungen.
Precisely centred starts and low feed force for demanding metalwork
The HSS‑G twist drill DIN 338 type N, short, ground, bright, with 135° split point cross grind is a precision tool for professional metalworking. This short DIN 338 twist drill, also offered as a precision HSS type N drill, combines a ground profile from high‑performance high‑speed steel with a polished, uncoated surface and a 135° split point for reliable centring.
Designed for universal use on normal cutting materials, the geometry of the type N core provides low feed force and strong centring behaviour. The polished bright surface reduces friction and prevents chip build‑up on soft, lubricious materials such as aluminium and plastics, while the cross‑grind at the tip (split point) minimises wandering during the initial drill entry.
Technical data at a glance
- material: high‑speed steel (HSS‑G)
- standard: DIN 338 (short)
- type: type N core geometry
- surface: bright / uncoated / ground and polished
- point: 135° split point with cross grind
- universal geometry for normal‑cutting materials
- optimised flute polish for smooth chip evacuation
- suited to hand‑held drills, bench and pillar drills
Advantages you can measure
- Reduced feed force thanks to the 135° split point, lowering operator effort and tool stress.
- Cleaner holes and longer tool life due to razor‑sharp ground cutting edges and precise run‑out accuracy.
- Lower risk of build‑up on the cutting edge when machining soft metals and polymers because of the bright, low‑friction surface.
- Reliable centring on flat or curved surfaces—preceding centre‑punching is often unnecessary.
- Smooth chip evacuation through highly polished flutes for uninterrupted production runs.
Why choose Metav as your precision partner Metav democratises precision by making high‑quality measuring and cutting tools accessible to every workshop. Based in Emmerich, Metav acts as a quality filter for the European market, combining decades of expertise with an inventory of over 250,000 products. More than 48,000 customers trust Metav for consistent supply and clear, dependable order processing—advantages that make Metav an efficient single‑source partner for machining consumables and tooling.
In short: the HSS‑G twist drill DIN 338 type N, short, ground, bright, with 135° split point cross grind is a robust allrounder for craft and serial production, offering precise centring, outstanding chip control and reduced machining effort.
FAQ
Which materials are suitable for this HSS‑G twist drill?
The HSS‑G twist drill with type N geometry is intended for normal‑cutting materials and performs particularly well on non‑ferrous metals (for example aluminium) and various plastics due to its bright, low‑adhesion surface.
Do I need to centre‑punch before drilling?
The 135° split point cross grind significantly improves self‑centring; for many flat or slightly curved surfaces a prior centre‑punch is not required, reducing setup time.
Is the drill coated?
This short DIN 338 twist drill is supplied bright and uncoated (polished), which reduces build‑up when machining lubricious materials.
Can I use this drill in hand‑held machines as well as pillar drills?
Yes. The DIN 338 short format is designed for use in hand‑held drills, bench and pillar drills, offering reliable run‑out accuracy across these machine types.
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com