Durable indexable inserts for efficient metalcutting
Indexable inserts are hardened cutting elements designed to deliver consistent material removal in metalworking, providing cost-effective tool life management and repeatable results for turning, milling and drilling operations. Suited for machining steel, stainless and heat-resistant alloys, these inserts offer rapid edge renewal and reduced downtime through simple indexing, while versions optimised for internal coolant significantly improve chip control and thermal management in demanding applications. By choosing the right insert grade and geometry you gain improved tool life, predictable wear behaviour and better surface finish thanks to enhanced chip control, with key benefits including wear-resistant carbide, internal coolant compatibility and reliable chip breaking.
CCMT09T302-FP4 WPP10G WPP10G Wendeplatten - Walter Tools
Take advantage of the combination of high wear resistance, precise geometry and optimised chip control for reliable production with reduced downtime. Order the CCMT09T302-FP4 WPP10G inserts via Metav Werkzeuge or consult the specialists for application-specific recommendations. CCMT09T302-FP4 WPP10G — Turning and drilling indexable insert, Tiger‑tec Gold for Stahl | Walter Tools A precision CCMT09T302-FP4 WPP10G indexable insert designed for turning and boring applications, optimised for machining Stahl with a Tiger‑tec Gold coating. Tiger‑tec Gold coating for long tool life FP4 chipbreaker for controlled chip formation Rhombus 80° geometry for versatile turning 7° clearance and 0.2 mm corner radius for fine finishes Consistent performance through advanced coating technology The combination of the Tiger‑tec Gold platform and the grade WPP10G delivers measurable improvements in wear behaviour and process stability when machining Stahl. The engineered multi-layer coating reduces flank and crater wear under the thermal loads typical of steel turning and boring, which means fewer tool changes and more predictable life cycles. For production environments seeking repeatable results, this coating technology supports higher cutting parameters while maintaining component quality. Geometry and chip management that support productivity The Rhombus 80° form paired with the FP4 chipbreaker provides balanced cutting action for both conventional and light interrupted cuts. A 0.2 mm corner radius helps achieve good surface integrity at moderate feeds, while the 7° clearance angle reduces rubbing and heat build-up. Together these features enable stable chip evacuation and consistent surface finish, reducing cycle times and the need for secondary operations in many turning and boring tasks. Application guidance and process advantages for Stahl machining The grade is specified for ISO group P applications and is tailored to the machining behaviour of unalloyed and alloyed Stahl. In practice, this means the insert performs well across a range of feeds and speeds commonly used in general-purpose turning and boring. The combination of controlled chip formation and robust cutting edge results in higher effective tool life and fewer interruptions for regrinding or index changes. For mixed-batch or high-volume production, the result is improved throughput and lower unit machining costs without compromising surface quality. Contact Metav Werkzeuge for tailored advice on Walter Tools inserts and their application in Stahl machining; consultants are available at info@metav-werkzeuge.com or by phone at +49 2822 7131930 Technical data SKU: CCMT09T302-FP4-WPP10G-WALTER Article: CCMT09T302-FP4 WPP10G Product type: Turning and drilling indexable insert / indexable cutting insert Manufacturer: Walter Tools Facts Clearance angle: 7° Corner radius: 0.2 mm Insert size: 09 Insert thickness: T3 Tolerance class: M Materials & special features Coating/grade: Tiger‑tec Gold, WPP10G Chipbreaker: FP4 Shape: Rhombus 80° Application: Stahl (ISO group P) Series: Tiger‑tec Gold Execution: T FAQ What materials is the CCMT09T302-FP4 WPP10G suitable for? The CCMT09T302-FP4 WPP10G insert is specified for Stahl (ISO group P), covering a broad range of unalloyed and alloyed steels encountered in machining. How does the Tiger‑tec Gold coating benefit production? The Tiger‑tec Gold coating on the CCMT09T302-FP4 WPP10G reduces flank and crater wear, allowing more consistent cutting parameters and extended tool life in demanding Stahl applications. Which features improve chip control with this insert? Chip management is enhanced by the FP4 chipbreaker and the Rhombus 80° geometry, which together promote controlled chip formation and reliable evacuation during turning and boring. Is the insert suitable for finishing operations? With a 0.2 mm corner radius and 7° clearance, the insert balances edge strength and finish capability, making it appropriate for many finishing and semi-finishing tasks on Stahl components. What distinguishes this Walter Tools grade from general-purpose inserts? The WPP10G grade, part of the Tiger‑tec Gold series, is engineered for a mix of wear resistance and toughness optimised for Stahl machining, providing consistent performance over varied cutting conditions. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenzeichen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers Walter Tools.
CCMT09T302-FP4 WPP20G WPP20G Wendeplatten - Walter Tools
Take advantage of the combination of Tiger·tec Gold coating and the FP4 chipbreaker to achieve reliable chip control and longer tool life in steel turning; order directly via Metav Werkzeuge or consult the technical team for process optimisation. CCMT09T302-FP4 WPP20G — Indexable turning/boring insert for steel by Walter Tools A CCMT09T302-FP4 WPP20G insert engineered for productive steel machining with the Tiger·tec Gold coated carbide grade. Tiger·tec Gold coated for extended tool life Optimised FP4 chipbreaker for stable chips Rhombic 80° CCMT geometry for versatile turning Designed for machining steel with reliable wear resistance High process reliability for steel turning The insert from the Tiger‑tec Gold series is designed specifically for the ISO P material group and delivers consistent wear resistance and process stability when machining unalloyed and alloyed steel. The WPP20G grade combines a coated carbide substrate with a modern PVD/CVD-type surface treatment to reduce flank wear and increase tool life under typical steel cutting temperatures. As a result, cycle times are more predictable and tool change intervals lengthen, which supports continuous production runs and reduces overall machining costs. Improved chip control and surface quality The dedicated FP4 chipbreaker is shaped to promote reliable chip formation across a range of cutting conditions, reducing risk of entanglement and improving evacuation. The Rhombic 80° geometry supports stable contact conditions and can help to achieve a better workpiece finish in general turning operations. Together, the chipbreaker and geometry enable machining strategies that favour fewer interruptions and more consistent surface integrity, which is particularly valuable in batch production and component finishing. Predictable cutting behaviour through precise geometry Key geometry data such as the 0.2 mm corner radius and the 7° clearance angle contribute to stable engagement and loaded-edge distribution during cutting; the insert’s T3 thickness and size 09 format provide a compact cutting edge ideal for medium to fine turning passes. These dimensional features reduce the tendency for vibration in moderate setups and allow for controlled feed rates that match the radius and toolholder stiffness, supporting repeatable part tolerances and improved process capability. Practical handling and application recommendations The CCMT format insert is compatible with common turning toolholders that accept rhombic 80° inserts and is suited to both roughing and finishing sequences when paired with appropriate feeds and speeds. Because the grade is specified for steel (ISO P), it offers a balance between wear resistance and toughness—making it a versatile choice across a broad range of steel components. Walter Tools’ material and coating technology aim to combine productivity with dependable edge security, supporting consistent results in industrial turning applications. Contact Metav Werkzeuge for application advice, availability and to request CCMT09T302-FP4 WPP20G inserts by Walter Tools via info@metav-werkzeuge.com or +49 2822 7131930 Technical Data Article number: CCMT09T302-FP4-WPP20G-WALTER Designation: CCMT09T302-FP4 WPP20G Product type: Bohr-/Aufbohrwendeschneidplatte / Drehwendeschneidplatte Manufacturer: Walter Tools Core specifications Corner radius: 0.2 mm Clearance angle: 7° Thickness: T3 Size: 09 Tolerance class: M Grade / Sort: WPP20G Features / Special features Coating: Tiger·tec Gold Chipbreaker: FP4 Shape: Rhombic 80° Series: Tiger‑tec Gold Material application: Steel (ISO P) Execution: T Plate form: CCMT geometry FAQ Is this insert suitable for stainless steel? The data indicate the insert grade is specified for steel (ISO P); suitability for stainless steel is not stated for the CCMT09T302-FP4 WPP20G and would require verification against specific stainless grades. What benefits does the WPP20G grade provide? The WPP20G grade from the Tiger·tec Gold series offers a coated carbide construction that emphasises wear resistance and general-purpose performance when machining steel, improving tool life and process stability. What types of operations is the FP4 chipbreaker intended for? The FP4 chipbreaker is optimised for controlled chip formation in turning operations on steel, supporting reliable evacuation and consistent cut behaviour across varying depths of cut. How does the 0.2 mm corner radius influence machining? A 0.2 mm corner radius on the insert balances edge strength and achievable surface finish; it suits medium to fine turning passes where moderate feed rates are used to avoid premature edge overload. Can the CCMT09T302-FP4 WPP20G handle interrupted cuts? The grade and geometry provide good toughness for general steel machining, but severe interruptions depend on machine rigidity and holder setup; the CCMT09T302-FP4 WPP20G is intended for stable turning conditions within its steel application range. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Protected trademarks and trade names are the property of their respective owners. Trademarks and protected product names are mentioned only for explanatory purposes. There is no connection between our company and the mentioned brands. The offered article is original factory‑new goods of the manufacturer.
CCMT09T302-FW4 WPP20G Wendeplatten - Walter Tools
Take advantage of the Tiger‑tec Gold coating and the WPP20G grade combined with the stable FW4 chipbreaker to achieve reliable, repeatable turning performance on steel; order the inserts through Metav Werkzeuge or consult Metav's specialists for application-specific recommendations. CCMT09T302-FW4 WPP20G turning insert — Tiger‑tec Gold, for steel applications | Walter Tools CCMT09T302-FW4 WPP20G is an indexable turning insert designed for general steel machining, featuring a rhombic 80° geometry and a Tiger‑tec Gold coating for robust performance Tiger‑tec Gold coating for longer tool life Universal WPP20G grade for steel machining Rhombic 80° geometry, 0.2 mm nose radius FW4 chipbreaker for controlled chip formation Consistent productivity through optimised cutting materials The combination of the WPP20G grade and the Tiger‑tec Gold coating provides a balance between wear resistance and toughness that is tailored to steel machining. As a result, the insert offers stable chip formation and predictable edge life, which supports uninterrupted production cycles and reduces unexpected tool changes. The material selection and coating technology are engineered to cope with the thermal and mechanical conditions typical for P‑group materials according to ISO 513, making this indexable insert a reliable choice for mixed‑batch and continuous turning. Geometry that improves surface quality and tool reliability The rhombic 80° shape and the 0.2 mm nose radius deliver a good compromise between accessibility and surface finish for general turning tasks. The built‑in 7° clearance reduces rubbing on the flank while the FW4 chipbreaker controls chip shape across a range of feeds, which helps to maintain a consistent cutting zone and repeatable part tolerances. These geometric features translate into fewer reworks and a steadier process, particularly when machining various steels where chip control and repeatable contact conditions are essential. Clear guidance on application and grade selection The WPP20G designation denotes a coated carbide grade optimised for steel (material group P). It is intended as a universal grade offering balanced wear resistance and toughness, suitable for common unalloyed and alloyed steels. For users less familiar with ISO classifications, this means the insert is designed to handle the typical heat generation and chip behaviour encountered during steel turning, while the Tiger‑tec Gold coating enhances surface hardness and oxidation resistance at cutting temperatures. This clarity supports confident grade selection for a wide range of turning operations. Handling and integration into tool systems The insert size and thickness (CCMT format) suit standard turning tool holders that accept CCMT‑style plates; correct clamping and a secure pocket fit are essential to exploit the stable cutting edge properties. While recommended cutting parameters depend on part geometry and machine capability, the indexable tip is engineered to deliver consistent performance across typical workshop speeds and feeds for steel. For precise cutting data or advice on toolholder matching, technical consultants at Metav Werkzeuge can provide application‑specific recommendations and machining parameters. Contact details: info@metav-werkzeuge.com, +49 2822 7131930. Contact Metav Werkzeuge to discuss suitability for specific steel grades, confirm stock for CCMT09T302-FW4 WPP20G inserts, or request tailored machining recommendations based on the Tiger‑tec Gold technology Technical data SKU: CCMT09T302-FW4-WPP20G-WALTER Label: Drehwendeschneidplatte CCMT09T302-FW4 WPP20G Walter Tools Product type: Turning insert (indexable) Manufacturer: Walter Tools Internal designation: CCMT09T302-FW4 ISO designation: CCMT09T302-FW4 WPP20G Core measurements Size code: 09 Nose radius: 0.2 mm Clearance angle: 7° Plate thickness: T3 Tolerance class: M Plate form: Rhombic 80° Chipbreaker: FW4 Special features Coating/series: Tiger‑tec Gold Grade: WPP20G (coated carbide) Material group: P — steel (ISO 513) Designed for: stable chip formation and general turning of steel Typical advantages: wear resistance, toughness balance, reliable cutting edge FAQ What steels is this insert best suited for? The CCMT09T302‑FW4 WPP20G insert is designed for the P material group and is suitable for common unalloyed and alloyed steels according to ISO 513. How does the Tiger‑tec Gold coating improve performance? Tiger‑tec Gold on the WPP20G grade increases surface hardness and oxidation resistance at elevated cutting temperatures, which supports longer edge life and more consistent wear behaviour when turning steel. What does the FW4 chipbreaker do in practice? The FW4 chipbreaker promotes controlled chip formation across a range of feeds, reducing the likelihood of long, stringy chips and aiding stable cutting conditions during turning operations. Is the insert compatible with standard CCMT tool holders? The CCMT09T302 geometry corresponds to standard CCMT‑style pockets; proper clamping and seat contact are required to ensure the expected stability and repeatable performance. Can the WPP20G grade be used for stainless steel or other non‑steel alloys? WPP20G is optimised for steel (P group); for stainless or other specialised alloys, consider grades specifically developed for those materials to maintain cutting edge life and process reliability. Manufacturer: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen; Germany Trademarks and product names are the property of their respective owners. Brand names are mentioned for explanation only; there is no affiliation between our company and the named brands. The offered item is original, factory‑new goods of the manufacturer.
CCMT09T302-FW4 WSM20S FW4 Wendeplatten - Walter Tools
Take advantage of the combination of Tiger·tec Silver coating and the FW4 chipbreaker for stable cutting performance in stainless steels and heat-resistant alloys; order the CCMT09T302-FW4 WSM20S inserts directly via Metav Werkzeuge or consult our specialists for tailored application advice. CCMT09T302-FW4 WSM20S indexable turning insert — Tiger·tec Silver grade, FW4 chipbreaker, Walter Tools A CCMT09T302-FW4 WSM20S indexable turning insert designed for machining stainless steels and heat‑resistant superalloys in demanding turning operations Tiger·tec Silver coating for edge stability Optimised FW4 chipbreaker for secure chip control Rhombic 80° geometry with 0.2 mm corner radius Suitable for stainless steels and superalloys Reliable cutting performance on stainless steels and superalloys The combination of the WSM20S grade and Tiger·tec Silver coating provides a balance of heat resistance and wear protection that supports consistent cutting performance in materials classified under ISO group M (stainless steels) and S (heat‑resistant superalloys and titanium). The specialised coated carbide composition favours stable chip formation and helps to mitigate built‑up edge, which is a common challenge when turning high‑toughness materials. This results in predictable tool life and reduced variability in process outputs, supporting production planning and quality control. Geometry and chip control that enhance surface quality The FW4 chipbreaker is engineered to produce controllable, segmented chips in a variety of cutting conditions; combined with the rhombic 80° form and a 0.2 mm corner radius, the insert offers a compromise between robustness and fine surface finish. These geometric features help to maintain a reliable cutting edge and reduce the risk of chatter when used with appropriate machine settings. For operators less familiar with chipbreaker function: it directs chip flow and breaks chips into manageable lengths, improving evacuation and reducing tool and workpiece damage. Process efficiency and application suitability With a T3 insert thickness and a medium tolerance class, this indexable insert is suitable for stable, repeatable turning operations where durability and productivity matter. The grade is optimised for demanding applications such as bar turning, face and light profiling of stainless components, and hard‑to‑machine alloys where edge stability and thermal resistance improve throughput. Selecting the correct insert geometry and cutting data will enable lower downtime, fewer regrinds and more consistent batch quality, offering a tangible contribution to overall machining economics. For tailored recommendations on insert variants and cutting data for Walter Tools CCMT09T302-FW4 WSM20S, contact Metav Werkzeuge for application support and availability. Technical data Article number: CCMT09T302-FW4-WSM20S-WALTER Designation: CCMT09T302-FW4 WSM20S Product type: Indexable turning insert Series: Tiger·tec Silver Manufacturer: Walter Tools Core specifications Relief angle: 7° Corner radius: 0.2 mm Insert size: 09 Thickness: T3 Geometry: Rhombic 80° Chipbreaker: FW4 Special features Grade: WSM20S (coated carbide) Material suitability: stainless steels (ISO M), heat‑resistant superalloys and titanium (ISO S) Tolerance class: M Stable cutting edge and good chip control Designed for productive machining of challenging materials FAQ What materials is this insert suitable for? The WSM20S grade is formulated for stainless steels (ISO M) and can also be applied to heat‑resistant superalloys (ISO S) depending on the geometry and cutting conditions. How does the FW4 chipbreaker improve machining? The FW4 chipbreaker shapes and breaks chips into manageable segments, improving evacuation and reducing the risk of damage to the insert or workpiece during turning. What does the 0.2 mm corner radius mean for performance? A 0.2 mm corner radius provides a balance between edge strength and surface finish: it gives sufficient durability for continuous cuts while enabling a finer surface on the workpiece. Is this insert suitable for finishing and roughing operations? The insert’s geometry and Tiger·tec Silver coating make it versatile; with adjusted cutting data it can be used for light finishing and steady medium‑duty turning, prioritising edge stability and repeatability. Can this insert be used on titanium alloys? Depending on the component and cutting strategy, the grade can be applied to titanium (ISO S) where thermal and edge stability are required; optimised parameters and coolant strategy are recommended. Manufacturer/Responsible: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen; Germany Protected trademarks and product names are the property of their respective owners. Walter Tools is named for explanation purposes. There is no affiliation between our company and the mentioned manufacturers. The offered item is an original, factory‑new product from the stated manufacturer.
CCMT09T304 WKK20S MK4 Wendeplatten - Walter Tools
Take advantage of the combination of Tiger·tec Silver wear resistance and the MK4 chipbreaker geometry for reliable cast-iron turning and boring operations; order directly via Metav Werkzeuge or contact the consultants for application advice and specification matching. CCMT09T304-MK4 WKK20S turning/boring indexable insert for cast iron by Walter Tools The CCMT09T304-MK4 WKK20S is a rhombic 80° coated carbide insert designed for productive boring and turning of cast iron, offering optimised chip control and reliable edge life. Tiger·tec Silver coating for durable wear resistance Optimised MK4 chipbreaker for cast iron applications Rhombic 80° form with 0.4 mm corner radius 7° relief angle for stable cutting performance High wear resistance for abrasive cast-iron work The combination of the Tiger·tec Silver coating and the WKK20S grade provides a clear advantage when machining cast iron: the coating reduces abrasive wear while the substrate keeps the cutting edge stable under intermittent, breaking-chip conditions. For production environments that prioritise uptime and repeatable tool life, this insert offers a measurable increase in process reliability. The coated carbide composition is tuned to resist the typical abrasive loading of grey and nodular cast irons, translating into longer tool life and fewer insert changes during shifts. Geometry that improves chip control and surface integrity The MK4 chipbreaker paired with the rhombic 80° geometry delivers controlled chip formation and evacuation, especially important in interrupted cuts and varying cross-sections common to boring operations. The small 0.4 mm corner radius balances edge strength with surface finish capability, while the 7° relief angle reduces rubbing and heat generation at the tool–workpiece interface. These geometric choices help to maintain a consistent cutting action and reduce the risk of built-up edge, which in turn supports better component tolerances and surface quality. Process advantages: efficiency and predictable performance Choosing an insert from the Tiger·tec Silver family supports higher process stability and reduced variability. The grade’s wear behaviour enables consistent machining parameters over longer tool life, which can lower total operating costs through fewer tool changes and less machine downtime. In day-to-day operations, this means more predictable cycle times and improved throughput without compromising component accuracy—key considerations for batch production or lights-out machining cells. Practical application and mounting guidance Designed for turning and boring operations, the indexable insert fits standard holders that accept the CCMT 09 profile and T3 thickness. The medium tolerance class provides reliable seating and repeatable positioning in the toolholder, ensuring that the insert geometry performs as intended. When integrating this insert into an existing tool setup, consider modest finishing feeds with the 0.4 mm radius to exploit the balance between strength and surface finish, and ensure chip evacuation through appropriate coolant application or flute geometry in the holder. Contact Metav Werkzeuge for cutting tests and specification matching of the Walter Tools CCMT09T304-MK4 WKK20S insert — call +49 2822 7131930 or eMail info@metav-werkzeuge.com Technical data Article number: CCMT09T304-MK4-WKK20S-WALTER Designation: CCMT09T304-MK4 WKK20S Type: Bohr-/Aufbohrwendeschneidplatte / Drehwendeschneidplatte Series: Tiger·tec Silver Grade: WKK20S Manufacturer: Walter Tools Facts Relief angle: 7° Corner radius: 0.4 mm Plate form: Rhombus 80° Plate size: 09 Plate thickness: T3 Tolerance class: M Special features MK4 chipbreaker Coated carbide grade Suitable for cast iron machining Intended for boring and turning applications FAQ What materials is this insert suitable for? The insert is specified for machining cast iron; the WKK20S grade and Tiger·tec Silver coating are optimised for abrasive cast-iron behaviour. How does the MK4 chipbreaker benefit chip control? The MK4 geometry shapes chips to break reliably when turning or boring cast iron, improving evacuation and reducing the risk of entanglement in the machining zone. Which toolholder profile matches the insert? Holders accepting the CCMT 09 insert profile and T3 thickness are appropriate; the tolerance class M ensures repeatable seating for stable cutting. What surface finish can be expected with the 0.4 mm corner radius? The 0.4 mm radius balances edge strength and finish capability, enabling good surface integrity in standard finishing passes on cast iron. Is this insert part of a coating family with other grades? Yes, this insert belongs to the Tiger·tec Silver series; the WKK20S grade is the variant tailored for cast-iron applications. Protected trademarks and trade names are the property of their respective owners. Brand names are used for explanation only; there is no connection between our company and the named manufacturers. The offered item is original, factory-new goods of Walter Tools. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen, Germany
CCMT09T304-E47 WPP20G WPP20G Wendeplatten - Walter Tools
Take advantage of the combination of Tiger·tec Gold coating and a robust WPP20G grade for reliable steel machining; the 7° clearance and 0.4 mm corner radius ensure consistent edge engagement and controlled chip formation. For procurement or tailored cutting data, order the insert via Metav Werkzeuge or consult the technical team for specific cutting recommendations. CCMT09T304-E47 WPP20G drilling/boring indexable insert for steel — Tiger·tec Gold | Walter Tools A CCMT09T304-E47 WPP20G drilling/boring indexable insert designed for productive steel machining, combining a Tiger·tec Gold coated carbide grade with a dedicated E47 chipbreaker and rhombic 80° form. Tiger·tec Gold coated carbide Optimised for steel machining (ISO P) 7° clearance angle Rhombic 80° form, 0.4 mm corner Increased process reliability through advanced coating and grade The coated carbide in the Tiger·tec Gold family delivers a balanced combination of wear resistance and toughness that supports longer tool life in demanding turning and boring cycles. The WPP20G grade is formulated for steel applications (ISO P) and designed to provide stable chip formation under typical steel-cutting temperatures. By choosing a coated indexable insert from this series, production engineers benefit from predictable tool behaviour and fewer interruptions for insert changes, which helps maintain consistent cycle times and component tolerances. Consistent cutting geometry for reproducible results The insert’s rhombic 80° geometry and 0.4 mm corner radius enable reliable engagement and secure clamping in boring and drilling toolholders. The specified 7° clearance reduces rubbing at the flank face and supports favourable cutting forces, while the E47 chipbreaker promotes controlled chip segmentation for swarf evacuation. These geometrical features translate into repeatable surface finishes and dimensional stability during series runs, simplifying process development and reducing downstream rework. Practical selection and integration in workshops This insert variant, supplied in thickness T3 and tolerance class M, fits established toolholders and is supplied in Walter’s Tiger-tec Gold series, allowing quick integration into existing tooling systems without major adjustments. The grade’s focus on steel (ISO P) means cutting parameters can be standardised across a range of unalloyed and alloyed steels, improving setup efficiency and easing tool management. For operations seeking a dependable balance between economy and performance, the grade’s combination of coating technology and chip control offers a pragmatic route to improved productivity. Contact Metav Werkzeuge for availability and customised cutting data for the CCMT09T304-E47 WPP20G insert — Metav Werkzeuge will advise on optimal feeds, speeds and holder compatibility Technical data SKU: CCMT09T304-E47-WPP20G-WALTER Article designation: CCMT09T304-E47 WPP20G Product type: Drilling/boring indexable insert Manufacturer: Walter Tools Core data Clearance angle: 7° Corner radius: 0.4 mm Insert size: 09 Thickness: T3 Tolerance class: M Special features Coating: Tiger·tec Gold Grade: WPP20G Chipbreaker: E47 Form: Rhombic 80° Applicable material group: Steel (ISO P) Series: Tiger-tec Gold Execution: T FAQ What materials is this insert suitable for? The CCMT09T304-E47 WPP20G insert is suitable for machining steel and is specified for ISO P group applications. What advantage does the Tiger·tec Gold coating provide? The Tiger·tec Gold coating on the WPP20G grade enhances wear resistance and toughness, improving tool life during steel machining operations. Can the insert be used in standard drilling and boring holders? Yes, the CCMT09T304-E47 geometry and T3 thickness are compatible with common drilling and boring indexable insert holders designed for rhombic 80° inserts. How does the E47 chipbreaker affect chip control? The E47 chipbreaker is engineered to promote controlled chip segmentation and evacuation, supporting safer swarf handling and more stable cutting conditions. Is this insert intended for finishing or roughing operations? The WPP20G grade is designed as a versatile, general-purpose coated carbide suitable for a range of operations in steel; cutting parameters should be selected according to the desired material removal rate and surface finish. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen The Walter AG (brand: Walter Tools), headquartered in Tübingen, is one of the world’s leading manufacturers of precision tools for metalworking and is part of the Swedish Sandvik Group. Protected trademarks and trade names are the property of their respective owners. Brand names and trademarks are mentioned for explanatory purposes only; there is no affiliation between our company and the named brands. The offered item is an original, factory-new product from the manufacturer.
CCMT09T304-E47 WPP20S WPP20S Wendeplatten - Walter Tools
Take advantage of Tiger·tec Silver performance and the balanced WPP20S grade for reliable steel machining: a robust Rhombic 80° geometry with a 0.4 mm corner radius and 7° relief delivers stable chip control and repeatable results. Order the CCMT09T304-E47 WPP20S directly via Metav Werkzeuge or request further advice from the consultants. CCMT09T304-E47 WPP20S drilling/boring indexable insert — Tiger·tec Silver, for steel, Walter Tools CCMT09T304-E47 WPP20S is a drilling/boring indexable insert designed for productive steel machining in demanding turning and bore-finishing operations Tiger·tec Silver coating for productive machining ISO P compatibility for steel applications Rhombic 80° geometry with 7° relief E47 chipbreaker for controlled chip formation Consistent machining quality through coated-carbide grade and geometry The combination of the WPP20S grade and Tiger·tec Silver coating offers a balanced mix of wear resistance and toughness, optimised for steel (ISO P) machining. This coated carbide formulation is developed to handle the typical heat and chip formation of steel cutting, reducing flank wear and extending edge life. The Rhombic 80° outline provides a versatile effective cutting edge for drilling-related turning and bore operations, while the 0.4 mm corner radius increases edge strength, improving surface finish and part consistency without compromising tool life. Reliable chip control and process stability for productive cycles Built around the E47 chipbreaker, the insert controls chip form and evacuation under standard steel cutting conditions, reducing interruptions and keeping cycle times steady. The 7° relief reduces rubbing and cutting forces, helping to maintain thermal stability in the cut. With tolerance class M and a T3 thickness, the insert offers predictable seating and repeatable position accuracy in standard toolholders, supporting unattended or high-volume runs with fewer interruptions and more consistent part quality. Practical advantages for workshop and production environments The format and dimensions (insert size 09) make this grade suitable for a wide range of toolholders and applications where steel turning and boring tasks require both productivity and surface integrity. The coated carbide substrate resists built-up edge and improves edge retention, which translates into fewer tool changes and lower machining downtime. By selecting this insert, process planners benefit from a stable, general-purpose solution that balances tool life and productivity for mixed batch production. Application guidance and selection rationale For steels and typical carbon and alloy steels (ISO P), the WPP20S grade is recommended where a combination of economical wear resistance and dependable toughness is required. The insert's chip control and geometry suit finishing and medium-turning passes associated with boring and internal profiling. When specifying the cutting data, factor in the corner radius for surface finish targets and choose feeds that avoid excessive edge load to exploit the grade’s wear resistance while preserving cutting-edge integrity. Choose the CCMT09T304-E47 WPP20S from Walter Tools for a dependable balance of productivity and edge life — contact Metav Werkzeuge for order placement or technical clarification at info@metav-werkzeuge.com or +49 2822 7131930 Technical data SKU: CCMT09T304-E47-WPP20S-WALTER Article designation: CCMT09T304-E47 WPP20S Series: Tiger·tec Silver Manufacturer: Walter Tools Facts Relief angle: 7° Corner radius: 0.4 mm Insert size: 09 Thickness: T3 Tolerance class: M Special features Grade: WPP20S (coated carbide) Shape: Rhombic 80° Chipbreaker: E47 Material application: Steel (ISO P) Execution: T FAQ What materials is this insert suitable for? The CCMT09T304-E47 WPP20S is designed for steel applications (ISO P); the WPP20S grade and Tiger·tec Silver coating are optimised for the heat and chip characteristics of unalloyed and alloyed steels. How does the E47 chipbreaker affect machining? The E47 chipbreaker promotes controlled chip formation and evacuation in steel machining, which reduces workpiece damage and machine interruptions during drilling-related turning and boring tasks. What advantages does the 0.4 mm corner radius offer? A 0.4 mm corner radius increases edge strength for better surface finish and improved resistance to edge chipping, supporting stable finishing passes without excessive tool wear. Is this insert suitable for finishing or roughing? With the coated WPP20S grade and its balanced wear/toughness profile, the insert suits finishing and medium turning; its chip control also supports process stability during light to moderate stock removal. How precise is the insert seating and repeatability? The insert is supplied to tolerance class M and a T3 thickness, providing predictable seating and repeatable positioning in standard toolholders for consistent part tolerances. Manufacturer: Walter Tools; part of the Walter AG group, headquartered in Tübingen, Germany; www.walter-tools.com Protected trademarks and product names are the property of their respective owners. Brand names are mentioned for explanation only; no connection between Metav Werkzeuge and the listed brands is implied. The offered item is an original, factory-new product of the manufacturer.
CCMT09T304-E47 WSM20S WSM20S Wendeplatten - Walter Tools
Combining the Tiger·tec Silver coating with the WSM20S grade and a 0.4 mm corner radius delivers dependable edge stability and improved chip control for demanding stainless steel and heat‑resistant alloys; order directly via Metav Werkzeuge or consult our specialists for application advice. CCMT09T304-E47 WSM20S Bohr-/Aufbohrwendeschneidplatte — Walter Tools, Tiger·tec Silver for stainless steel and superalloys A CCMT09T304-E47 WSM20S indexable insert engineered to ensure stable cutting performance when machining stainless steel and heat‑resistant superalloys in demanding turning operations Tiger·tec Silver coated carbide grade WSM20S Suitable for stainless steel and superalloys Rhombic 80° insert with 0.4 mm corner radius 7° clearance angle for stable chip control Reliable performance for stainless steel and superalloys The Tiger·tec Silver grade WSM20S is designed specifically for difficult‑to‑machine materials such as stainless steel (ISO group M) and heat‑resistant alloys (ISO group S). With a coated carbide substrate and a focus on edge stability, this grade reduces the tendency to form built‑up edge and copes better with the elevated cutting temperatures typical of these alloys. The result is more consistent surface finish and extended tool life compared with uncoated or general‑purpose grades. This makes the insert suitable where reproducible results and reduced downtime are priorities. Geometry and coating that improve process stability The Rhombic 80° form combined with a 0.4 mm corner radius and 7° clearance provides an effective balance between strength and cutting precision. The chipbreaker E47 is tuned to promote reliable chip formation under interrupted or continuous cuts, lowering the risk of chip entanglement and workpiece damage. The T3 thickness enhances seat stability in the tool holder, which translates into reduced vibration and improved repeatability. These geometric choices support higher productivity by allowing mid‑range feeds and speeds with secure edge life. Practical benefits for workshop efficiency Adopting this insert supports predictable machining cycles: the WSM20S coating technology improves thermal resistance, while the insert geometry delivers controlled chip evacuation and stable cutting forces. For production environments this translates into fewer tool changes, fewer scrap parts and a lower total cost of machining per component. Where setup variety exists, the insert’s universal rhombic angle and robust grade simplify inventory needs by covering multiple applications in stainless steel and superalloy machining. For advice on cutting data or holder compatibility, our technical consultants can provide tailored recommendations. Notes on application and handling When orienting the insert in the cutter body, ensure correct seating and clamping torque to preserve the specified 0.4 mm corner integrity and to maintain the intended chipbreaker function. For highest reliability, verify coolant strategy and monitor temperatures during trial cuts — the coating and grade are optimised for thermal loads, but stability benefits are maximised with suitable cutting conditions. If uncertain which geometry or grade matches a specific alloy and process, request a quick cutting test plan from Metav Werkzeuge to determine optimal parameters. Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenbezeichnungen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers. For machining stainless steel and heat‑resistant alloys with reliable edge life, contact Metav Werkzeuge for availability and tailored application support — eMail: info@metav-werkzeuge.com, Tel: +49 2822 7131930 Technical data Article number: CCMT09T304-E47-WSM20S-WALTER Product designation: Bohr-/Aufbohrwendeschneidplatte CCMT09T304-E47 WSM20S Brand: Walter Tools Series: Tiger·tec Silver Facts Insert size: 09 Corner radius: 0.4 mm Clearance angle: 7° Shape: Rhombus 80° Thickness: T3 Grade/sort: WSM20S Chipbreaker: E47 Tolerance class: M Material groups: S / M Special features Coating technology: Tiger·tec Silver Application focus: stainless steel, heat‑resistant superalloys (ISO groups M and S) Execution: T ISO designation: CCMT09T304-E47 WSM20S Series description: Coated cemented carbide insert optimised for thermal and edge stability FAQ Which materials is this insert suitable for? This CCMT09T304-E47 WSM20S insert by Walter Tools is designed for stainless steel (ISO group M) and heat‑resistant superalloys/titanium (ISO group S) as indicated by the grade WSM20S. What advantage does the Tiger·tec Silver coating offer? The Tiger·tec Silver coating on the WSM20S grade enhances thermal resistance and edge stability, enabling more consistent tool life and improved surface finish when machining challenging alloys. How does the chipbreaker E47 affect performance? The E47 chipbreaker promotes controlled chip formation and evacuation under a range of feeds, reducing the chance of chip build‑up and supporting uninterrupted production when using the CCMT09T304‑E47 geometry. What do the geometry values mean for setup? The Rhombic 80° form with a 0.4 mm corner radius and 7° clearance gives a robust cutting edge for strength, while permitting accurate profiling and good seating in standard holders designed for CCMT inserts. Is this insert compatible with standard CCMT toolholders? Yes, the ISO designation CCMT09T304‑E47 WSM20S corresponds to standard CCMT toolholder interfaces; ensure correct clamping and seat condition to preserve the specified performance. Hersteller: Walter Tools; Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen
CCMT09T304-E47 WSM30S WSM30S Wendeplatten - Walter Tools
Take advantage of the combination of thermal stability, precise chip control and a robust edge geometry for reliable drill and boring performance in demanding materials; order directly via Metav Werkzeuge or consult the technical team for application support. CCMT09T304-E47 WSM30S drilling/boring indexable insert — Tiger·tec Silver, 0.4 mm corner radius, Walter Tools CCMT09T304-E47 WSM30S is an indexable insert designed for drilling and bore-enlarging operations in demanding materials such as stainless steels and superalloys Tiger·tec Silver coating for high heat resistance Optimised E47 chipbreaker for stable chip control Rhombic 80° CCMT insert with 0.4 mm corner radius Ideal for stainless steels and superalloys (M/S) Consistent performance in heat‑sensitive materials The WSM30S grade, part of the Tiger·tec Silver family, is a coated carbide designed to withstand the thermal and chemical stresses typical of machining stainless steels and heat‑resistant superalloys. The coating improves heat resistance and reduces adhesion at the cutting edge, which helps prevent built‑up edge and extends tool life. For operations where temperature control and edge stability determine productivity, this insert delivers repeatable results and lower scrap rates. Precision edge geometry for improved surface finish The rhombic 80° CCMT geometry with a 0.4 mm corner radius combines strength and access to narrow features, enabling reliable contact in both drilling and bore‑enlarging cycles. The E47 chipbreaker is engineered to form short, controllable chips under varying feed rates, reducing the risk of chip entanglement and improving process stability. The result is a finer surface finish and fewer interruptions for chip clearing during batch production runs. Practical integration for efficient production With T3 plate thickness and tolerance class M, the insert fits standard CCMT toolholders and maintains positional accuracy across tool changes. The combination of a robust corner radius and a coated substrate supports higher metal removal rates without compromising repeatability. Maintenance intervals are extended thanks to the stable cutting edge, which contributes directly to lower tool consumption and improved overall equipment effectiveness in high‑mix or continuous manufacturing environments. Contact Metav Werkzeuge for tailored tooling recommendations for Walter Tools CCMT09T304-E47 WSM30S and to check availability — phone +49 2822 7131930 or email info@metav-werkzeuge.com Technical data Article number: CCMT09T304-E47-WSM30S-WALTER SKU: CCMT09T304-E47-WSM30S-WALTER Manufacturer: Walter Tools Product type: drilling/boring indexable insert Series: Tiger·tec Silver Grade: WSM30S Numbers / Facts Corner radius: 0.4 mm Clearance angle: 7° Plate form: Rhombic 80° Plate size code: 09 Chipbreaker: E47 Plate thickness: T3 Tolerance class: M Special features / Versions Coated carbide grade Tiger·tec Silver (WSM30S) Optimised chip geometry for short chip formation Suited for stainless steels (M) and superalloys/titanium (S) CCMT indexable shape for drilling and bore‑enlarging applications Stable cutting edge for high‑temperature resistance and process security FAQ What materials are suitable for this insert? The CCMT09T304-E47 WSM30S insert is designed for stainless steels and heat‑resistant superalloys (ISO groups M and S), offering thermal stability and controlled chip formation in those materials. Which toolholders accept this insert geometry? Rhombic CCMT toolholders that accommodate CCMT09T3 inserts are compatible; the insert’s T3 thickness and 0.4 mm corner radius ensure secure seating and repeatable clamping. How does the E47 chipbreaker improve machining? The E47 chipbreaker produces short, controlled chips across a range of feeds and depths, reducing chip congestion and helping to maintain continuous cutting without frequent interruptions. Is the WSM30S grade coated and what are the benefits? Yes — WSM30S is a coated carbide grade within the Tiger·tec Silver family; the coating increases heat resistance, reduces adhesion at the cutting edge and supports longer tool life in demanding materials. What does tolerance class M indicate for performance? Tolerance class M denotes a manufacturing accuracy that supports consistent seating and interchangeability, contributing to reliable repeatability and predictable results in series production. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Protected trademarks and trade names are the property of their respective owners. Brand names and protected trademarks are mentioned for explanatory purposes only. There is no connection between our company and the mentioned brands. The offered item is original, brand‑new merchandise from the manufacturer.
CCMT09T304-FK6 WKK10S Wendeplatten - Walter Tools
Benefit from the combination of Tiger·tec Silver wear resistance and the WKK10S grade tuned for abrasive cast iron; consistent cutting performance and reliable chip control reduce downtime and improve throughput. Order directly via Metav Werkzeuge or consult our specialists for process advice. CCMT09T304-FK6 WKK10S – Indexable turning and boring insert for cast iron, Tiger·tec Silver, Walter Tools The CCMT09T304-FK6 WKK10S is an indexable turning and boring insert engineered for productive machining of cast iron, combining a dedicated chipbreaker and a coated carbide grade for dependable material removal. Tiger·tec Silver coating for wear resistance Optimised for cast iron (ISO K) 0.4 mm corner radius for stable cutting 7° clearance angle for versatile turning Consistent performance for abrasive cast iron work The coated carbide grade WKK10S, part of the Tiger·tec Silver family, is formulated for the specific demands of cast iron machining. Its coating technology increases resistance to abrasive wear and heat, which translates into longer tool life and fewer interruptions for insert changes. In practice this means more predictable cycle times and improved process stability when machining short, breaking chips typical of cast materials. The insert’s FK6 chipbreaker is matched to these chip characteristics, promoting controlled chip formation and safe evacuation during turning and boring operations. Technical design that supports precision and surface finish With a 0.4 mm corner radius and a 7° clearance angle, the geometry balances edge strength and the ability to produce stable cutting lines. The Rhombus 80° plate shape provides a versatile cutting edge orientation for both external turning and boring or facing passes, while the plate thickness T3 ensures rigidity under moderate cutting loads. These design choices reduce vibration and support higher feed rates without compromising the targeted surface quality, making the insert suitable for industrial production runs where repeatability matters. Practical benefits and process efficiency Specifying this insert helps to lower tooling costs per part by extending insert life through improved wear behaviour and optimised chip control. The combination of a coated grade and a dedicated chipbreaker reduces flank wear and the risk of built-up edge, which in turn maintains dimensional accuracy over longer tool-life windows. For operations focused on throughput and low variance, the insert supports stable toolpaths and predictable regrinding or indexing intervals, aiding in leaner setup strategies and less scrap. Contact Metav Werkzeuge for application-specific recommendations on Walter Tools Tiger·tec Silver inserts or request a quote by e‑mail at info@metav-werkzeuge.com or by phone on +49 2822 7131930 Technical data Article number: CCMT09T304-FK6-WKK10S-WALTER Designation: CCMT09T304-FK6 WKK10S Manufacturer: Walter Tools Numbers / Core technical data Clearance angle: 7° Corner radius: 0.4 mm Plate size: 09 Plate thickness: T3 Tolerance class: M Designs / Special features Coating: Tiger·tec Silver Grade: WKK10S Chipbreaker: FK6 Plate form: Rhombus 80° Material group: K (cast iron) Execution: T FAQ Which materials is this insert suited to? The CCMT09T304-FK6 WKK10S is specifically designed for cast iron (ISO group K); the grade and chipbreaker respond well to the abrasive, brittle nature of these materials. What performance advantages does the Tiger·tec Silver coating provide? The Tiger·tec Silver coating on this grade improves resistance to abrasive wear and heat, resulting in longer insert life and more consistent cutting performance in cast iron applications. How does the FK6 chipbreaker affect machining? The FK6 chipbreaker promotes controlled, short chip formation typical for cast iron, easing chip evacuation and reducing the risk of entanglement or surface damage. Can this insert be used for both turning and boring operations? Yes, the rhombic geometry and the 7° clearance angle allow the insert to be used effectively in external turning and in boring or face-turning tasks where the cutting edge orientation and stability are appropriate. Manufacturer/Responsible: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen; Germany The Walter AG (marketed as Walter Tools) is one of the world’s leading manufacturers of precision tools for metalworking and is part of the Sandvik Group. Protected trademarks and trade names remain the property of their respective owners. Mention of brand names is for explanation only; there is no affiliation implied. The offered article is original, factory-new merchandise of the manufacturer.
CCMT09T304-FK6 WKK20S Wendeplatten - Walter Tools
Efficient machining of abrasive cast-iron components is enabled by the combination of WKK20S Tiger·tec Silver coating and the FK6 chipbreaker, which delivers consistent chip control and long tool life; order the CCMT09T304-FK6 WKK20S directly via Metav Werkzeuge or ask the consultants if needed. CCMT09T304-FK6 WKK20S indexable insert — 7° clearance, Rhombic 80° geometry (Walter Tools) A CCMT09T304-FK6 WKK20S indexable insert engineered for productive turning and boring of cast iron, offering a coated carbide grade and a chipformer tailored to brittle, short-chip materials. Tiger·tec Silver coated carbide Optimised for cast iron (K) FK6 chipbreaker for stable chip control 7° clearance, Rhombic 80° geometry Productivity and wear resistance for cast iron production The coated carbide grade WKK20S, applied with Tiger·tec Silver technology, is optimised for the abrasive wear typical of cast iron machining. Its formulation balances toughness and hardness to maintain a stable cutting edge under the intermittent, brittle-chip conditions of grey and nodular cast irons. The FK6 chipbreaker promotes reproducible, short-chip formation, reducing risk of chip entanglement and improving process reliability. Specifying this grade supports higher productivity by extending tool life and lowering indexable insert change frequency in batch and series production. Geometry that reduces cutting forces and stabilises machining The Rhombic 80° shape combined with a 7° clearance angle yields a versatile cutting geometry that balances accessibility and edge strength for internal boring and external turning operations. The 0.4 corner radius helps distribute cutting forces at the nose, diminishing local stress peaks and improving edge robustness during interrupted cuts. Thickness designation T3 provides the mechanical stiffness required for stable clamping in standard toolholders. These geometric choices translate into predictable tool behaviour, improved surface finishes and fewer rejects in demanding casting removal or finish passes. Practical benefits in process integration and tool management Integration into existing tool systems is straightforward thanks to the standard CCMT form and consistent tolerances. The insert's indexable nature enables simple repositioning of fresh cutting edges, lowering downtime compared with brazed or solid tools. For process planning, the coated grade and chipbreaker combination supports elevated cutting parameters for roughing operations on cast iron while still permitting controlled finishing passes when required. Using a structured inventory of these inserts can reduce setup variability and contribute to leaner changeover routines on turning centres and boring bars. Quality assurance and application guidance Walter Tools' manufacturing standards ensure reproducible geometry and coating performance across batches. For best results, pair the insert with toolholders rated for CCMT-style inserts and verify clamping torque to prevent micro-movements. In abrasive cast-iron work, coolant strategy and cutting speed adjustments can further extend edge life; the WKK20S grade is designed to tolerate typical coolant conditions used in workshop and production environments. The combination of Tiger·tec Silver coating and the FK6 chipbreaker supports consistent part quality and predictable maintenance intervals. For reliable cast-iron turning and boring with Walter Tools' Tiger·tec Silver technology, contact Metav Werkzeuge for stock availability and technical advice via info@metav-werkzeuge.com or call +49 2822 7131930. Technical data Article number: CCMT09T304-FK6-WKK20S-WALTER Name: CCMT09T304-FK6 WKK20S Type: Boring/turning indexable insert Manufacturer: Walter Tools Core data Clearance angle: 7° Corner radius: 0.4 mm Plate size: 09 Thickness: T3 Shape: Rhombic 80° Tolerance class: M Special features Grade: WKK20S Series: Tiger·tec Silver Chipbreaker: FK6 Application: cast iron (K) Geometry designation: CCMT09T304-FK6 FAQ What cast-iron grades is this insert intended for? The CCMT09T304-FK6 WKK20S insert is formulated for cast iron (ISO group K), with the WKK20S grade tuned to handle abrasive wear and short-chip tendencies. How does the FK6 chipbreaker affect chip formation? The FK6 chipbreaker on this insert promotes short, manageable chips during cast-iron machining, improving process safety and reducing chip-related interruptions. Can the insert be used in standard CCMT toolholders? Yes, the insert follows the CCMT form factor and is compatible with standard toolholders designed for that geometry; correct clamping is essential for repeatable results. What advantage does Tiger·tec Silver coating provide? The Tiger·tec Silver coating enhances wear resistance and thermal stability, supporting higher cutting parameters and longer edge life in abrasive cast-iron applications. Is the insert suitable for finishing as well as roughing? While optimised for robust roughing of cast iron, the combination of geometry and grade also permits controlled finishing passes when appropriate machining parameters are selected. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenbezeichnungen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers Walter Tools.
CCMT09T304-FM4 WMP20G WMP20G Wendeplatten - Walter Tools
Benefit from the combination of Tiger·tec Gold coating and the WMP20G grade for secure machining of rostfreier Stahl; the rhombic 80° insert with a 7° relief angle and FM4 chipbreaker delivers consistent chip control and extended tool life. Order the CCMT09T304-FM4 WMP20G insert directly via Metav Werkzeuge or consult the advisers for application support. CCMT09T304-FM4 WMP20G Rhombic 80° turning insert, Tiger·tec Gold – Walter Tools The CCMT09T304-FM4 WMP20G is a rhombic 80° indexable turning insert engineered for machining rostfreier Stahl under medium to robust cutting conditions, offering optimised wear resistance and stable chip formation. Tiger·tec Gold coating for extended wear resistance Optimised FM4 chipbreaker for stable chip control Rhombic 80° geometry with 7° relief angle 0.4 mm corner radius for reliable edge strength Longer productive life with advanced coating technology The combination of the Tiger·tec Gold coating and the WMP20G grade is designed to increase the wear resistance and preserve the cutting edge when machining tough-to-cut materials such as rostfreier Stahl. In practice, this means fewer insert changes and more productive cutting time on turning lines. The coating technology supports thermal stability and reduces detrimental build-up on the edge, which directly benefits process reliability and lowers the effective tooling cost per part. Predictable chip control and robust edge behaviour The FM4 chipbreaker is optimised for secure chip breaking in medium to heavy operations, producing short, controllable chips that ease evacuation and reduce the risk of entanglement. Paired with the rhombic 80° geometry and a 0.4 mm corner radius, the insert provides a balanced combination of strength and versatility: the geometry supports stable cutting directions while the 7° relief angle reduces rubbing and improves surface finish. These features translate into dependable component quality and consistent cycle times. Practical fitment and handling for production workshops As a standard CCMT-format insert, the component fits conventional CCMT toolholders and can be integrated into established turning setups without redesign. The T3 plate thickness offers the necessary rigidity for interrupted or steady cuts, while the insert size 09 is suitable for a wide range of bore and external turning tasks. For setup recommendations or material-specific parameters, Metav Werkzeuge provides technical guidance; further assistance and data can be requested via eMail: info@metav-werkzeuge.com or by phone: +49 2822 7131930. Reliable brand performance for demanding stainless applications Walter Tools delivers consistent manufacturing quality and process security; the Tiger·tec Gold series and the WMP20G grade are tailored for applications where rostfreier Stahl tends to work-harden and generate heat at the cutting zone. Choosing a proven insert reduces downtime risk and supports repeatable surface quality. For workshops aiming to improve throughput while maintaining edge life, this insert represents a pragmatic choice that balances performance and longevity. Contact Metav Werkzeuge today for application-specific recommendations on Walter Tools Tiger·tec Gold inserts or to secure the CCMT09T304-FM4 WMP20G for production use Technical data Article number: CCMT09T304-FM4-WMP20G-WALTER Designation: CCMT09T304-FM4 WMP20G Manufacturer: Walter Tools Core data Insert size: 09 Plate thickness: T3 Corner radius: 0.4 mm Clearance angle: 7° Plate form: Rhombus 80° Special features Coating: Tiger·tec Gold Grade: WMP20G Chipbreaker: FM4 Suitable for: rostfreier Stahl Series: Tiger-tec Gold FAQ Which materials is this insert suitable for? The CCMT09T304-FM4 WMP20G insert from Walter Tools is intended primarily for rostfreier Stahl (ISO group M) and is optimised for medium to robust machining conditions. What advantage does the FM4 chipbreaker provide? The FM4 chipbreaker on the insert promotes stable, short chips and consistent chip evacuation, improving machining security and reducing the likelihood of chip interference. How does the Tiger·tec Gold coating help in production? Tiger·tec Gold increases thermal and wear resistance, which supports longer tool life and more consistent cutting-edge behaviour when machining rostfreier Stahl. Is the insert compatible with standard CCMT toolholders? Yes, the CCMT format is compatible with standard CCMT indexable toolholders, allowing straightforward replacement and integration into existing turning setups. What does the 0.4 mm corner radius affect in practice? A 0.4 mm corner radius enhances edge strength and helps maintain surface quality under intermittent or heavier cutting loads, balancing finish and durability. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen
CCMT09T304-FM4 WMP20S WMP20S Wendeplatten - Walter Tools
Take advantage of the combination of Tiger·tec Silver surface technology, the WMP20S grade and the compact Rhombic 80° form for dependable machining of stainless steel; order directly via Metav Werkzeuge or contact their consultants for application-specific advice. CCMT09T304-FM4 WMP20S – indexable turning insert for stainless steel, Tiger·tec Silver · Walter Tools CCMT09T304-FM4 WMP20S is a rhombic 80° indexable insert designed for reliable turning of stainless steel under medium to robust cutting conditions. Tiger·tec Silver coating for improved wear resistance Optimised for stainless steel machining Rhombic 80° form with 0.4 mm corner radius Chipbreaker FM4 for controlled chip formation Consistent performance for stainless steel turning The Tiger·tec Silver surface treatment combined with the WMP20S grade provides a balance between wear resistance and edge stability when machining stainless steel. As a coated carbide insert, it supports reliable chip formation even where material toughness and heat generation are challenges. The combination of coating and substrate helps to extend tool life and reduce the frequency of index changes, improving uptime in repetitive turning operations. Geometry that secures edge life and dimensional accuracy The Rhombic 80° form and a 0.4 mm corner radius offer a compromise between a sharp cutting edge and robust support for the insert corner, reducing the risk of chipping in interrupted cuts. A 7° relief angle favours a positive cutting geometry that reduces radial forces and can lower power draw in many turning applications. The insert thickness T3 and size 09 make this part suitable for a wide range of standard toolholder systems while preserving rigidity and heat dissipation at the cutting zone. Chip control and predictable tool life for productive cycles Equipped with the FM4 chipbreaker, this indexable insert promotes short, manageable chips when turning stainless steel, which decreases the likelihood of built-up edge and improves surface finish consistency. The grade is specified for medium to robust use, giving a predictable wear pattern across serial production runs. Fewer unexpected tool changes translate directly into higher overall productivity and lower process variability. Practical integration and process advice The insert is supplied in the common CCMT format and is compatible with standard CCMT toolholders; its design simplifies inventory management where mixed-material production demands flexibility. For selection of cutting data, holder geometry or to confirm compatibility with a specific machine spindle, consult the technical advisors at Metav Werkzeuge for tailored recommendations based on workpiece material and process parameters. Contact Metav Werkzeuge for a customised recommendation on the Walter Tools CCMT09T304-FM4 WMP20S indexable insert, or request cutting-parameter support by email at info@metav-werkzeuge.com or by phone at +49 2822 7131930 Technical data Article number: CCMT09T304-FM4-WMP20S-WALTER Description: Turning/indexable insert CCMT09T304-FM4 WMP20S Walter Tools Grade: WMP20S Series: Tiger·tec Silver Shape designation: Rhombic 80° Chipbreaker: FM4 Facts Relief angle: 7° Corner radius: 0.4 mm Size: 09 Special features Coated carbide construction Thickness: T3 Optimised for stainless steel Suited to medium to robust cutting conditions FAQ What materials is this insert intended for? The CCMT09T304-FM4 WMP20S insert is optimised for stainless steel and is formulated to manage the toughness and heat characteristics typical of those alloys. How does the Tiger·tec Silver series benefit tool life? The Tiger·tec Silver technology on the WMP20S grade enhances wear resistance and contributes to stable cutting edges during extended turning cycles with stainless steel. Which chip form can be expected with the FM4 chipbreaker? The FM4 chipbreaker on this insert promotes controlled, shorter chips suited to turning operations, reducing the risk of entanglement and improving surface quality. Is the insert compatible with standard CCMT toolholders? Yes, this CCMT-format insert fits standard CCMT toolholders; confirm seat and clamping specifications with Metav Werkzeuge for precise holder matching. What edge radius and relief angle are provided and why do they matter? The insert features a 0.4 mm corner radius and a 7° relief angle; this combination balances corner strength with favourable cutting geometry for consistent dimensional accuracy. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen, Germany Protected trademarks and trade names are the property of their respective owners. Brand names and trademarks are mentioned for explanatory purposes only; there is no affiliation between our company and the named manufacturers. The offered item is original, factory-new product of the stated manufacturer.
CCMT09T304-FM4 WMP30G WMP30G Wendeplatten - Walter Tools
Take advantage of the combination of Tiger‑tec Gold grade, a proven FM4 chipbreaker and a rhombic 80° geometry to ensure stable chip formation and consistent component quality in stainless steel production; order the insert directly via Metav Werkzeuge or contact the consultants for tailored recommendations. CCMT09T304-FM4 WMP30G indexable insert for stainless steel machining — Walter Tools The CCMT09T304-FM4 WMP30G is an indexable turning insert designed for medium to robust machining of stainless steel, combining a Tiger‑tec Gold coated grade with an FM4 chipbreaker for secure chip control. Tiger‑tec Gold coating for improved tool life Optimised FM4 chipbreaker for secure chip control Designed for stainless steel machining Rhombic 80° form with 0.4 mm corner radius High-performance grade for demanding stainless steel operations The WMP30G grade, part of the Tiger‑tec Gold series, is a coated carbide solution engineered to cope with the thermal and adhesive challenges of stainless steels. Its chemical and mechanical coating characteristics promote stable cutting edges and reduced tendency for built-up edge formation, which translates into fewer interruptions during production and a more predictable tool life. Using a grade tuned for these materials minimises rework and supports higher process reliability on turned parts where consistency of surface and dimensional accuracy matters. Reliable chip control and improved surface integrity Built around an FM4 chipbreaker and a Rhombic 80° geometry, the insert offers controlled chip formation and effective evacuation even under interrupted cuts. The combination of 7° clearance angle and a 0.4 mm corner radius supports a good balance between cutting strength and edge sharpness, enabling stable cutting forces and a superior surface finish. For shops seeking to reduce secondary finishing operations, this geometry assists in maintaining component tolerances and producing consistent finishes across batches. Production-ready design that reduces machine downtime With a thickness of T3 and a compact 09 insert size, this solution fits common toolholders and is suitable for serial production where quick insert changes and repeatability are essential. The indexable design simplifies maintenance: worn edges are replaced rapidly without regrinding, lowering setup times and boosting throughput. The coated carbide construction further increases time between changes, while the FM4 chip management reduces the risk of tool-related interruptions. For pragmatic workshop integration, the combination of grade and geometry means predictable process behaviour and straightforward inventory handling. Contact Metav Werkzeuge for tailored tooling advice on the Walter Tools CCMT09T304-FM4 WMP30G to secure optimised performance in stainless steel machining. Technical Data SKU: CCMT09T304-FM4-WMP30G-WALTER Designation: CCMT09T304-FM4 WMP30G Type: Drilling/reaming and turning indexable insert Core specifications Insert size: 09 Thickness: T3 Clearance angle: 7° Corner radius: 0.4 mm Insert form: Rhombic 80° Tolerance class: M Features and applications Grade: WMP30G Series: Tiger‑tec Gold Chipbreaker: FM4 Material group: M (stainless steel) Cutting material: coated carbide Shape: Rhombic 80° FAQ Which materials is the insert suitable for? The CCMT09T304-FM4 WMP30G is specified for machining stainless steel and is optimised for the typical challenges of these alloys. What is the purpose of the FM4 chipbreaker? The FM4 chipbreaker on the CCMT09T304-FM4 WMP30G governs chip formation to improve evacuation and protect the cutting edge during continuous and interrupted cuts. How does the Tiger‑tec Gold series benefit production? The Tiger‑tec Gold coating on this grade enhances wear resistance and edge stability, extending the service life of the CCMT09T304-FM4 WMP30G under medium to robust conditions. What are the geometric key data to consider for holder selection? Key geometric data are the Rhombic 80° form, 0.4 mm corner radius and the 7° clearance angle; these determine the required toolholder compatibility. Hersteller: Walter Tools; Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Protected trademarks and trade names are the property of their respective owners. Brand names and protected trade names are mentioned for explanatory purposes only. There is no affiliation between our company and the mentioned brands. The offered article is original, factory-new goods of the manufacturer.
CCMT09T304-FM4 WSM01 WSM01 Wendeplatten - Walter Tools
Benefit from the combination of Tiger‑tec Silver thermal resistance, the WSM01 coated‑carbide grade and the FM4 chipbreaker for secure chip control and extended edge life; order the CCMT09T304‑FM4 WSM01 directly via Metav Werkzeuge or consult the team for cutting data and availability. CCMT09T304-FM4 WSM01 — Turning and drilling indexable insert for rostfreier Stahl and superalloys (Walter Tools) The CCMT09T304-FM4 WSM01 is a versatile indexable insert engineered for demanding turning and drilling/boring applications in rostfreier Stahl and heat‑resistant superalloys, offering a balance of edge stability and controlled chip formation. Tiger‑tec Silver coating for thermal stability WSM01 grade for rostfreier Stahl and superalloys FM4 chipbreaker for controlled chip formation Rhombic 80° CCMT shape with 0.4 mm corner radius Efficient chip control and thermal resistance for difficult materials The combination of the FM4 chipbreaker with the Tiger‑tec Silver series results in predictable chip formation and reduced heat impact on the cutting edge. For materials classified as M (rostfreier Stahl) and S (heat‑resistant superalloys/titanium), the insert’s geometry and surface treatment lower the risk of built‑up edge and thermal softening. This yields more consistent cycle times and fewer unplanned tool changes, supporting improved process reliability in batch and single‑piece production. The design is particularly suited to operations that prioritise stable metal removal and repeatable surface quality. Reliable edge life and surface finish through optimised geometry The WSM01 grade is a coated carbide formulation tuned for stability on tough materials; it offers a compromise between wear resistance and toughness to handle the high temperatures and adhesive tendencies of rostfreier Stahl. The 0.4 mm corner radius and 7° clearance angle provide strength at the cutting edge while permitting fine finishing cuts where required. The rhombic 80° CCMT form delivers flexible entry angles and good load distribution, which helps to maintain dimensional accuracy and an improved finished surface with less need for subsequent machining. Seamless integration into production for consistent productivity Designed as a direct fit into standard CCMT toolholders, the insert (designation CCMT09T304‑FM4 WSM01) simplifies tooling logistics and reduces setup time. The T3 plate thickness and the numbered size facilitate predictable clamping and repeatable positioning in automated tool systems. These attributes translate into measurable efficiency: fewer tool changes, consistent tool life across similar batches and enhanced throughput. When combined with suitable machining parameters and reliable coolant or cutting strategies, the insert contributes to lower manufacturing cost per part and a steadier surface quality that benefits downstream assembly and inspection processes. Contact Metav Werkzeuge for customised cutting data, availability and to discuss the best holder and parameter sets for Walter Tools inserts Technical data Article number: CCMT09T304-FM4-WSM01-WALTER Designation: CCMT09T304-FM4 ISO designation: CCMT09T304-FM4 WSM01 Series: Tiger‑tec Silver Grade: WSM01 Manufacturer: Walter Tools Core data Corner radius: 0.4 mm Clearance angle: 7° Plate size code: 09 Plate thickness: T3 Special features Chipbreaker: FM4 Plate form: Rhombus 80° (CCMT) Sortenkategorie: coated carbide Material applicability: S / M Suitable for: rostfreier Stahl and heat‑resistant superalloys (depending on geometry) FAQ What materials are best machined with this insert? The insert is intended for rostfreier Stahl (ISO group M) and heat‑resistant superalloys/titanium (ISO group S); the WSM01 grade and Tiger‑tec Silver series support secure chip formation and thermal resistance during machining. How does the FM4 chipbreaker influence machining results? The FM4 chipbreaker produces short, controllable chips and promotes consistent evacuation, which reduces the likelihood of surface damage and improves operator safety during turning and boring operations. What advantages does the 0.4 mm corner radius offer? A 0.4 mm corner radius balances edge strength and surface finish capability, allowing stable cutting under moderate depths of cut while still delivering acceptable surface integrity for many finishing passes. Is the CCMT shape suitable for interrupted cuts? The rhombic 80° CCMT geometry offers robust edge support and good entry angles, making it suitable for many interrupted and continuous cutting scenarios when paired with the correct grade and parameters. Which series or coating enhances thermal stability? The Tiger‑tec Silver series provides improved thermal resistance and wear behaviour, contributing to longer edge life on materials that generate high cutting temperatures. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Protected trademarks and trade names are the property of their respective owners. Brand names and protected designations are mentioned solely for explanatory purposes. There is no connection between our company and the named brands. The offered article is an original, new product from the manufacturer.
CCMT09T304-FM4 WSM10S WSM10S Wendeplatten - Walter Tools
Take advantage of the combination of long tool life, reliable chip control and broad material capability to improve cycle consistency and reduce downtime; order this insert through Metav Werkzeuge or consult the Metav team for application advice and availability. CCMT09T304-FM4 WSM10S – Indexable turning and boring insert, Tiger·tec Silver, Walter Tools The CCMT09T304-FM4 WSM10S is a rhombic 80° indexable insert designed for demanding turning and boring tasks in stainless steel and heat‑resistant alloys, delivering consistent edge stability and efficient chip control. Tiger·tec Silver coated carbide grade WSM10S Optimised FM4 chipbreaker for stable chips Rhombic 80° CCMT shape with 0.4 mm radius 7° clearance and T3 plate thickness Improved cutting reliability for hard-to-machine alloys The coated carbide formula of Tiger·tec Silver combined with the WSM10S grade is formulated for stainless steel and high‑temperature alloys, offering a balance between wear resistance and edge stability. This composition reduces the tendency for built-up edge and thermal degradation during prolonged cuts; the result is fewer tool changes and more predictable part quality. The material classification S / M denotes suitability for both superalloys and stainless steel, making the insert a versatile choice across mixed production batches. Explained simply, the coating increases heat resistance while the substrate supports mechanical strength at the cutting edge. Predictable chip formation and access in bores The FM4 chipbreaker is designed to produce controlled, segmented chips that evacuate reliably in both external turning and internal boring operations. Combined with the Rhombus 80° geometry and a 0.4 mm corner radius, the insert offers a compromise between edge strength and fine surface finish; a larger radius would increase tool strength but can limit fine finishing, whereas 0.4 mm preserves finishing potential while maintaining robustness. The geometry also assists in achieving consistent cutting forces, which is particularly important when machining materials that generate heat and strain the cutting edge. Practical handling, mounting and process benefits With a T3 plate thickness and 7° clearance, the insert provides stable clamping and reduced edge chipping under interrupted cuts. The standard CCMT09T304-FM4 designation eases tool selection and stock management across lathes and boring bars that accept 80° rhombic inserts. Fewer indices and predictable wear patterns contribute to lower setup time and simpler reconditioning decisions. For production environments, the combination of coherent geometry, dedicated chip control and a robust grade helps maintain cycle stability, reduces scrap rates and supports continuous improvement of machining parameters. For machining stainless steel and heat‑resistant alloys with enhanced process security, contact Metav Werkzeuge for tailored application support and immediate availability at info@metav-werkzeuge.com or by phone on +49 2822 7131930 Technical data Article number: CCMT09T304-FM4-WSM10S-WALTER SKU: CCMT09T304-FM4-WSM10S-WALTER Brand: Walter Tools Series: Tiger-tec Silver Core technical figures Clearance angle: 7° Corner radius: 0.4 mm Plate form: Rhombus 80° Plate size: 09 Plate thickness: T3 Designs and special features Grade: WSM10S Chipbreaker: FM4 Designation without grade: CCMT09T304-FM4 ISO designation: CCMT09T304-FM4 WSM10S Material suitability: S / M (superalloys; stainless steel) FAQ What materials is this insert suitable for? The CCMT09T304-FM4 WSM10S insert is suitable for stainless steel and heat‑resistant superalloys, denoted by the S / M classification. How does the FM4 chipbreaker improve machining? The FM4 chipbreaker on the CCMT09T304-FM4 WSM10S promotes segmented, manageable chips that reduce recutting and improve safety in both external turning and boring operations. What does the 0.4 mm corner radius mean for part finish? A 0.4 mm corner radius provides a compromise between edge strength and surface finish, helping to achieve fine finishes while maintaining resistance to chipping during interrupted cuts. Is this insert compatible with standard 80° holders? Yes, the rhombic 80° CCMT form matches standard 80° indexable holders for turning and boring tools. Which series and brand produce this grade? The insert belongs to the Tiger·tec Silver series by Walter Tools and is supplied in the WSM10S coated carbide grade. Hersteller: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Protected trademarks and trade names remain the property of their respective owners. Brand names and protected designations are mentioned solely for explanatory purposes; there is no affiliation between Metav Werkzeuge and the named brands. The item offered is an original, brand‑new product from the manufacturer Walter Tools.
CCMT09T304-FM4 WSM20S FM4 Wendeplatten - Walter Tools
Take advantage of the combination of high thermal resistance, precise geometry and stable chip control to maintain consistent productivity when machining stainless steels and heat‑resistant alloys; order the CCMT09T304-FM4 WSM20S directly via Metav Werkzeuge or ask our consultants for application advice. CCMT09T304-FM4 WSM20S turning indexable insert — Tiger‑tec Silver for stainless steels and superalloys | Walter Tools A CCMT09T304-FM4 WSM20S rhombic 80° turning insert designed for reliable performance in stainless steels and heat‑resistant superalloys Tiger‑tec Silver coating for heat resistance Designed for stainless steels and superalloys 7° clearance angle for secure chip control 0.4 mm corner radius for precise finishing Rhombic 80° form with FM4 chipbreaker High‑temperature coating that stabilises the cutting edge The combination of the Tiger‑tec Silver coating and the WSM20S carbide grade provides a measured increase in thermal resistance and edge stability when machining tough materials. Coatings in the Tiger‑tec Silver family are engineered to reduce built‑up edge and abrasion under higher cutting temperatures; this means fewer unplanned tool changes and more predictable component quality. In practical terms, the coated substrate supports consistent performance in applications where heat generation is significant, such as interrupted cuts or long turning passes in stainless steels and superalloys. Geometry engineered for consistent surface quality and chip control The rhombic 80° shape combined with a 7° clearance produces a cutting geometry that balances strength and accessibility for a wide range of turning tasks. The FM4 chipbreaker is tuned to promote controlled chip formation in ductile and work‑hardening materials, reducing the risk of long, stringy chips that can damage the part or tool. The 0.4 mm corner radius offers a compromise between edge strength and the ability to achieve fine surface finishes, making this insert suitable for finishing and light to medium turning operations where repeatable surface integrity is required. Design features that support steady productivity and tool life Built as a turning indexable insert with tolerance class M and thickness T3, this component is intended for series production environments where repeatability is essential. The grade and coating combination encourages stable wear patterns and predictable reconditioning intervals, which improves process planning and reduces downtime. Because the insert is indexed rather than resharpened, replacement is rapid and machining parameters remain consistent across insert changes, supporting leaner workflows on CNC lathes and turning centres. Practical application guidance for reliable setup This insert is recommended where machining of stainless steels or heat‑resistant alloys is the priority and where a balance between edge life and surface quality is required. For finishing passes choose moderate feeds with the 0.4 mm corner radius to preserve surface integrity; for more aggressive material removal, consider inserts with a larger radius or different grade. The rhombic angle permits access to shoulder and contour features while maintaining cutting stability. For specific holder choices or parameter windows tailored to a particular workpiece and machine, technical advice from Metav Werkzeuge can help fine‑tune the set‑up and cutting strategy. Contact Metav Werkzeuge to discuss Walter Tools’ Tiger‑tec Silver CCMT09T304-FM4 WSM20S inserts for your machining challenge and to arrange supply or tailored application support — call +49 2822 7131930 or email info@metav-werkzeuge.com Technical data SKU: CCMT09T304-FM4-WSM20S-WALTER Article designation: CCMT09T304-FM4 WSM20S Product type: Turning/boring indexable insert Manufacturer: Walter Tools Series: Tiger‑tec Silver Core technical data Clearance angle: 7° Corner radius: 0.4 mm Insert shape: Rhombic 80° Size: 09 Thickness: T3 Tolerance class: M Special features Carbide: coated carbide (WSM20S) Chipbreaker: FM4 Material suitability: S / M (heat‑resistant superalloys, titanium and stainless steels) Particularly suited to machining rostfreie Stähle and heat‑resistant alloys depending on geometry FAQ Which materials is this insert best suited for? The CCMT09T304-FM4 WSM20S insert from Walter Tools is designed primarily for stainless steels and for heat‑resistant superalloys (and titanium depending on application geometry), offering stable chip formation and edge integrity. What advantages does the Tiger‑tec Silver coating provide? The Tiger‑tec Silver coating increases thermal resistance and reduces adhesive wear, which helps the insert maintain a sharp, stable cutting edge under elevated temperatures common when machining stainless steels and superalloys. How does the FM4 chipbreaker influence machining results? The FM4 chipbreaker promotes short, manageable chips in ductile materials, improving surface finish consistency and reducing the risk of chip entanglement during continuous turning operations. When is the 0.4 mm corner radius recommended? A 0.4 mm corner radius is suitable for finishing and light to medium turning where surface quality is important while still providing sufficient edge strength for stable tool life. Is this insert suitable for series production? Yes; the insert’s coated grade, defined geometry and tolerance class M make it a reliable choice for series production, where repeatability and predictable tool life are required. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Protected trademarks and trade names are the property of their respective owners. Brand names and trademarks are mentioned for explanation only and do not imply any association between our company and the named manufacturers. The item offered is an original, factory‑new product from the manufacturer.
CCMT09T304-FM4 WSM30S Tiger-tec Silver Wendeplatten - Walter Tools
Take advantage of the wear-resistant Tiger·tec Silver coating and the heat-resistant WSM30S grade together with a Rhombus 80° geometry for consistent, productive machining of stainless steel and superalloys; order directly via Metav Werkzeuge or consult the technical team for application-specific recommendations. CCMT09T304-FM4 WSM30S – Drill/bore and turning indexable insert, Tiger·tec Silver (Walter Tools) CCMT09T304-FM4 WSM30S is a versatile indexable insert designed for drilling, boring and turning applications in demanding materials Tiger·tec Silver coating for heat resistance WSM30S grade for stainless steel and superalloys Rhombus 80° insert for versatile seat geometry FM4 chipbreaker for controlled chip formation Consistent tool life through advanced coating and grade The combination of the Tiger·tec Silver coating with the WSM30S coated carbide grade delivers improved resistance to abrasive wear and thermal loads. Intended primarily for machining of stainless steel (ISO group M) and heat-resistant superalloys (ISO group S), this specification supports stable cutting-edge performance and reduced flank wear. The result is longer tool life and fewer insert changes, which lowers overall cycle interruptions and improves process efficiency in production environments. Geometry and chip control for reliable cutting performance A Rhombus 80° shape paired with a compact 0.4 mm corner radius and the FM4 chipbreaker promotes predictable chip formation and secure edge strength during interrupted or continuous cuts. The insert’s 7° clearance angle reduces rubbing and heat build-up at the flank, while the T3 plate thickness ensures sufficient rigidity for demanding feeds. Together these geometry features translate into better surface finish and repeatable dimensional control on complex components. Broad application range and clear process benefits This insert suits applications where a balance of edge stability and heat resistance is required, for both drilling/boring and turning operations. With the CCMT form factor and robust chip control, the component is suitable for general workshop environments as well as high-volume production. The design supports ease of indexation and consistent seating in standard cutter bodies, helping to maintain spindle efficiency and reduce cycle-time variations over production runs. Simple selection and integration into machining processes Based on ISO material groups S and M, the specification streamlines grade selection for stainless steel and difficult-to-machine alloys. The compact geometry and proven chipbreaking strategy ease setup and process parameter definition: higher cutting speeds can be exploited where appropriate due to the coating’s thermal resistance, while feed and depth of cut remain optimised for edge integrity. This leads to measurable productivity gains and a lower cost per component in sustained processing. Contact Metav Werkzeuge for tailored advice on Walter Tools Tiger·tec Silver inserts and secure optimal parameters for stainless steel machining Technical data Article number: CCMT09T304-FM4-WSM30S-WALTER Designation: CCMT09T304-FM4 WSM30S Manufacturer: Walter Tools Facts Grade: WSM30S Coating: Tiger·tec Silver Material groups: S / M Corner radius: 0.4 mm Clearance angle: 7° Special features Insert form: Rhombus 80° Chipbreaker: FM4 Plate thickness: T3 Insert size: 09 Series: Tiger·tec Silver FAQ What materials is this insert intended for? This insert is specified for machining stainless steel (ISO group M) and heat-resistant superalloys/titanium (ISO group S) under the WSM30S grade and Tiger·tec Silver coating. Which chip control behaviour can be expected from the FM4 chipbreaker? The FM4 chipbreaker in this CCMT geometry promotes controlled, segmented chips for safer evacuation and stable cutting, particularly in turning and boring of ductile, heat-conductive materials. Is the CCMT09T304-FM4 compatible with standard toolholders for turning and boring? The CCMT09T304-FM4 WSM30S insert conforms to common CCMT indexable insert seats and can be mounted in standard turning and boring cutter bodies designed for Rhombus 80° inserts. How does the Tiger·tec Silver coating improve process reliability? The Tiger·tec Silver coating enhances thermal and abrasive resistance, allowing elevated cutting speeds and improved resistance to built-up edge when machining stainless steel and high-temperature alloys. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Protected trademarks and trade names remain the property of their respective owners. Brand names and protected trade names are mentioned solely for explanatory purposes. There is no connection between our company and the mentioned brands. The item offered is original, brand-new merchandise from the manufacturer (Walter Tools).
CCMT09T304-FM6 WSM20S FM6 Wendeplatten - Walter Tools
Benefit from the combination of WSM20S grade and Tiger·tec Silver coating for improved edge life and stable chip control when machining stainless steel and superalloys; order the CCMT09T304-FM6 WSM20S directly via Metav Werkzeuge or request application advice from our consultants. CCMT09T304-FM6 WSM20S indexable insert for stainless steel and superalloys — Tiger·tec Silver (Walter Tools) The CCMT09T304-FM6 WSM20S is an indexable cutting insert engineered for reliable chip control and durable edge stability in stainless steel and heat‑resistant alloys, suitable for drilling, boring and light turning tasks Tiger·tec Silver coating technology For stainless steel and superalloys FM6 chipbreaker for stable chip control Rhombus 80° insert with 0.4 mm nose radius Precision coating for extended tool life and consistent performance The Tiger·tec Silver coating provides a balanced combination of thermal resistance and toughness, designed to reduce flank wear and extend cutting edge life under elevated temperatures. Combined with the WSM20S cemented‑carbide grade, the insert maintains cutting performance when machining demanding materials. This means fewer interruptions for tool changes, steadier process windows and a more predictable cycle time for serial production, translating into measurable gains in productivity. Stable chip formation and process security for difficult materials The FM6 chipbreaker geometry is shaped to produce short, controlled chips even when cutting ductile, work‑hardening materials. When used on stainless steel or nickel‑based alloys, this geometry helps avoid chip entanglement and reduces the risk of built‑up edge formation. The rhombic 80° form and 0.4 mm nose radius support repeatable surface finish and tool engagement, making the insert suitable for operations where dimensional integrity and surface quality are required. Application clarity and economical machining outcomes Matched to heavy‑duty materials and, depending on the tool geometry, stainless steel, the insert offers a practical solution where tool life and process stability are priorities. The combination of grade and geometry supports higher metal‑removal rates with lower variance between runs, which improves throughput and reduces scrap. For shops transitioning to more heat‑resistant alloys, this insert provides a straightforward way to increase capability without complex process changes. Contact Metav Werkzeuge for tailored advice on Walter Tools Tiger·tec Silver inserts and to arrange delivery or technical consultation via info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: CCMT09T304-FM6-WSM20S-WALTER Designation: CCMT09T304-FM6 WSM20S Type: Indexable insert for drilling, boring and turning Manufacturer: Walter Tools Facts Relief angle: 7° Corner radius: 0.4 mm Insert size: 09 Thickness: T3 Tolerance class: M Special features Grade: WSM20S Chipbreaker: FM6 Coating: Tiger·tec Silver Plate form: Rhombus 80° Material suitability: S / M (superalloys/titanium; stainless steel) Series: Tiger‑tec Silver FAQ What materials is this insert suited for? The CCMT09T304-FM6 WSM20S insert is specified for machining stainless steel (ISO group M) and heat‑resistant superalloys/titanium (ISO group S), with the WSM20S grade optimised for those applications. How does the FM6 chipbreaker help in production? The FM6 chipbreaker on this Walter Tools insert promotes short, controllable chips, improving process security and reducing interruptions due to chip management in demanding materials. What geometry ensures surface quality with this insert? The rhombic 80° form combined with a 0.4 mm nose radius provides stable engagement and consistent surface finish, suitable for finishing and semi‑finishing passes. Is the coating suitable for high temperatures during cutting? Yes, the Tiger·tec Silver coating increases thermal resistance and protects the cutting edge, supporting longer tool life under elevated cutting temperatures. Can this insert be used for both drilling and turning operations? The insert is designed for a range of applications including drilling, boring and light turning, depending on toolholder design and setup; CCMT09T304-FM6 WSM20S offers the versatility required for mixed‑operation shops. Walter Tools / Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen, Germany Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenbezeichnungen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers.
CCMT09T304-FM6 WSM30S FM6 Wendeplatten - Walter Tools
Take advantage of the combination of Tiger·tec Silver coating, the WSM30S grade and the FM6 chipformer to ensure stable cutting edges and reliable chip control when machining stainless steel and heat‑resistant alloys; order directly via Metav Werkzeuge or consult our specialists for application support. CCMT09T304-FM6 WSM30S — Rhombic 80° indexable insert for drilling and turning | Walter Tools CCMT09T304-FM6 WSM30S is a coated carbide indexable insert developed for demanding drilling and turning tasks, especially suited to stainless steel and heat‑resistant superalloys Tiger·tec Silver coating for high temperature stability WSM30S grade for stainless steel and superalloys FM6 chipformer for reliable chip control Rhombic 80° shape with 0.4 mm corner radius Consistent performance in demanding materials The CCMT09T304-FM6 WSM30S insert combines a modern coating system with a purpose‑designed carbide grade to deliver predictable results when machining challenging workpiece materials. The Tiger·tec Silver coating improves heat resistance and reduces adhesion on the cutting edge, which is particularly beneficial for machining stainless steel and other tough alloys. The result is extended tool life and fewer interruptions to production, translating into measurable gains in throughput and process stability. Designed chip control for uninterrupted machining Efficient chip evacuation is critical in both drilling and turning operations. The FM6 chipformer geometry promotes short, controlled chips that reduce the risk of recutting and improve surface finish. Combined with the insert’s Rhombic 80° shape and 0.4 mm corner radius, the geometry supports consistent engagement and repeatable cutting behaviour. Operators gain a reliable cutting pattern that eases downstream processes and minimises cycle‑time variance. Precision geometry and trustworthy tolerances The insert’s 7° free angle, T3 plate thickness and tolerance class M reflect a balanced design for moderate to heavy cuts where edge stability matters. The compact 09 size suits a range of tool holders while maintaining rigidity at the cutting edge. For production engineers, these measurable specifications offer clear parameters for process planning, clamping and feed settings, supporting reproducible results across batches and shifts. Practical advantages for workshop integration The coated carbide grade WSM30S is tailored to resist thermal and mechanical stresses typical of high‑temperature alloys and stainless steel, reducing edge wear and built‑up edge formation. This contributes to fewer tool changes and consistent dimensional quality. The insert is compatible with standard indexable insert tool holders that accept the CCMT style, simplifying stock management and enabling quick replacement without additional setup complexity. What the technical characteristics mean in practice A 0.4 mm corner radius provides a compromise between strength and finish: larger radii boost edge life on roughing passes, while the moderate radius here helps maintain a good surface without excessive cutting forces. The Tiger·tec Silver coating lowers friction and improves oxidation resistance at elevated temperatures, so cutting parameters can be pushed further while maintaining safety margins. These features support higher productivity and lower overall cost per component. Trust Walter Tools' Tiger·tec Silver technology — contact Metav Werkzeuge for application advice and procurement at info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: CCMT09T304-FM6-WSM30S-WALTER Designation: CCMT09T304-FM6 WSM30S Manufacturer: Walter Tools Facts Free angle: 7° Corner radius: 0.4 mm Plate size: 09 Plate thickness: T3 Tolerance class: M Plate form: Rhombus 80° Special features Coating: Tiger·tec Silver Grade: WSM30S Chipformer: FM6 Series: Tiger‑tec Silver Suitable for: stainless steel (M), heat‑resistant superalloys and titanium (S) FAQ What materials is this insert designed for? The CCMT09T304‑FM6 WSM30S insert is designed for stainless steel and heat‑resistant superalloys, reflecting the WSM30S grade's emphasis on thermal resistance and stable cutting edges. How does the FM6 chipformer affect machining? The FM6 chipformer produces controlled, short chips that reduce recutting, improving surface quality and process reliability when using the CCMT09T304‑FM6 WSM30S insert. Can this insert be used for both drilling and turning? Yes, the CCMT09T304‑FM6 WSM30S is specified as a drilling and turning indexable insert, suitable for applications where the Rhombic 80° geometry and the grade properties are beneficial. What is the benefit of the Tiger·tec Silver coating? Tiger·tec Silver enhances heat resistance and reduces adhesion on the cutting edge, which helps maintain edge integrity and extend tool life in demanding operations with stainless steel. What does the 0.4 mm corner radius mean for surface finish? A 0.4 mm corner radius offers a balanced combination of edge strength and surface finish, supporting robust roughing passes while still delivering acceptable surface quality for many turning tasks. Protected trademarks and trade names remain the property of their respective owners. Brand names are mentioned for explanation only. There is no affiliation between our company and Walter Tools. The offered item is original factory‑new goods from the manufacturer. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen
CCMT09T304-FP4 WEP10C WEP10C Wendeplatten - Walter Tools
Benefit from the combination of the Walter Cermet WEP10C grade and the FP4 chipbreaker for consistent chip control and improved surface quality; the rhombic 80° geometry with a 0.4 mm corner radius provides reliable edge strength for precision turning. Order directly via Metav Werkzeuge or consult the technical team for suitability and delivery. CCMT09T304-FP4 WEP10C — Turning insert, Rhombus 80°, 7° clearance — Walter Tools The CCMT09T304-FP4 WEP10C is a rhombic turning insert in the Walter Cermet series, designed for indexable turning applications where consistent finishing and repeatable performance are required CCMT geometry, Rhombus 80° insert Walter Cermet WEP10C grade FP4 chipbreaker for reliable chip control 7° clearance angle with 0.4 mm corner radius High-grade cermet for stable surface quality and extended life The Walter Cermet WEP10C composition is engineered to deliver a consistent surface finish and enhanced tool life in applications that demand fine edges and wear resistance. As a cermet grade, it combines ceramic hardness with metallic toughness to resist abrasive wear while maintaining a reproducible cutting edge. This makes the insert suitable for processes where dimensional stability and low tool-wear variation are priorities, helping to reduce rework and enhance throughput. Geometry and chip control that support predictable machining The CCMT rhombic 80° form, combined with the FP4 chipbreaker and a 7° clearance, provides a balance of cutting stability and chip formation control. The modest 0.4 mm corner radius supports accurate corner strength without sacrificing detail in fine finishing passes. The FP4 geometry is optimised to break chips reliably under varying cutting conditions, contributing to cleaner toolpaths and reduced interruptions at the machine. Verify material compatibility via the product matrix for optimal selection Material suitability should be confirmed against the manufacturer’s product matrix to ensure the insert matches the intended workpiece material and cutting parameters. The grade and chipbreaker offer broad application potential, but specific recommendations depend on the workpiece alloy, hardness and cutting strategy. For clarity, request the matrix or technical data sheet to identify recommended cutting speeds, feeds and coolant strategy to achieve the best balance of productivity and lifetime. Process reliability and economic operation in production environments The combination of graded composition and controlled geometry supports process reliability and repeatable results in serial production. Stable edge behaviour and effective chip evacuation reduce downtime associated with edge wear and chip-related issues, contributing to overall machining economy. When integrated into a well-documented machining routine, the insert supports consistent cycle times and predictable maintenance intervals. Contact Metav Werkzeuge for an individual machining assessment of the Walter Tools CCMT09T304-FP4 WEP10C, including confirmation of material compatibility and delivery options via info@metav-werkzeuge.com or by phone at +49 2822 7131930 Technical Data Article number: CCMT09T304-FP4-WEP10C-WALTER Item designation: CCMT09T304-FP4 ISO designation: CCMT09T304-FP4 WEP10C Manufacturer: Walter Tools Series: Walter Cermet Grade: WEP10C Execution: T Core dimensions Clearance angle: 7° Corner radius: 0.4 mm Plate form: Rhombus 80° Plate size: 09 Plate thickness: T3 Tolerance class: M Special features FP4 chipbreaker Cermet cutting material Rhombic CCMT geometry Indexable turning / drilling-bore insert FAQ What materials is this insert suited for? Material suitability should be confirmed with the product matrix; the CCMT09T304-FP4 WEP10C is a cermet grade intended for applications that prioritise surface finish and wear resistance. How does the FP4 chipbreaker affect machining? The FP4 chipbreaker on the CCMT09T304-FP4 WEP10C promotes consistent chip formation and evacuation, reducing interruptions and improving process stability. What does the 0.4 mm corner radius influence? A 0.4 mm corner radius provides a compromise between edge strength and finishing precision, supporting accurate dimension control while maintaining resistance to edge chipping. Is the 7° clearance suitable for finishing cuts? The 7° clearance angle supports low-friction engagement and is compatible with finishing and light-medium duty turning passes when paired with the appropriate cutting data. Protected trademarks and trade names are the property of their respective owners. Brand names and registered marks are used solely for identification and explanatory purposes; no affiliation between our company and the mentioned brands is implied. The offered article is an original, factory-new product of Walter Tools. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen
CCMT09T304-FP4 WKP01G Wendeplatten - Walter Tools
Take advantage of a high-performance indexable insert that combines the wear-resistant Tiger·tec Gold coating with a proven WKP01G grade for reliable cutting on steel and cast iron; precise geometry and a dedicated FP4 chipbreaker support repeatable results and efficient material removal. Order directly via Metav Werkzeuge or consult our technical team for application-specific advice. CCMT09T304-FP4 WKP01G indexable turning insert — Tiger·tec Gold coating, 7° clearance (Walter Tools) A CCMT09T304-FP4 WKP01G indexable insert engineered for turning and boring operations, optimised for steel and cast iron applications with stable chip control and long tool life Tiger·tec Gold coating for extended tool life Suitable for steel and cast iron machining Rhombic 80° shape with 0.4 mm corner radius 7° clearance angle for stable cutting performance High productivity through advanced coating and grade The combination of the Tiger·tec Gold coating with the WKP01G carbide grade delivers a measurable improvement in process stability and tool life. Designed for typical steel and cast iron cutting conditions, the coated grade reduces abrasive and thermal wear, which means longer productive cutting time between indexings. For production environments where cycle time and predictable performance matter, this insert supports higher feeds and consistent component quality without frequent tool changes. Reliable chip control for safer, cleaner machining The integrated FP4 chipbreaker is tailored to break and evacuate chips efficiently during continuous turning and light boring. By controlling chip form and flow, the insert reduces the risk of entanglement and enhances surface finish consistency. This behaviour translates into fewer interruptions, safer operations on automated lathes, and lower risk of rework — an economical advantage for batch and single-piece manufacture alike. Geometry for stability and versatility in turning The rhombic 80° shape combined with a 0.4 mm corner radius and a 7° clearance angle provides a balanced compromise between strength and accessibility. The geometry supports robust cutting edge support for interrupted cuts while allowing access to shoulders and profiles where a larger nose radius would be restrictive. Plate thickness T3 and tolerance class M ensure the insert sits securely in standard toolholders, preserving repeatability and part accuracy. Clear application guidance and practical benefits Suited to a wide range of steels and cast irons under ISO P and K classifications, this insert simplifies tool selection for mixed-production environments. The CCMT designation indicates a rhombic, negative-profile insert with a 80° included angle, which is widely compatible with standard turning toolholders. Fewer tool changes and predictable wear behaviour lead to reduced setup time and more consistent output, supporting leaner workflows and higher overall equipment effectiveness. Contact Metav Werkzeuge for tailored cutting recommendations on Walter Tools inserts and to discuss the CCMT09T304-FP4 WKP01G for specific materials or cycle requirements — email info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: CCMT09T304-FP4-WKP01G-WALTER Product type: Indexable turning/boring insert Designation: CCMT09T304-FP4 WKP01G Manufacturer: Walter Tools Grade family: Tiger·tec Gold Grade: WKP01G Chipbreaker: FP4 Facts Corner radius: 0.4 mm Clearance angle: 7° Insert shape: Rhombic 80° Insert size: 09 Plate thickness: T3 Tolerance class: M Special features Coating technology: Tiger·tec Gold Carbide grade: WKP01G (coated cemented carbide) Material suitability: steel (ISO P), cast iron (ISO K) Intended use: turning and boring applications Chip control: FP4 chipbreaker Manufacturer brand: Walter Tools FAQ What materials is this insert suitable for? The CCMT09T304-FP4 WKP01G is designed for machining steel (ISO P) and cast iron (ISO K); the WKP01G grade and Tiger·tec Gold coating address the typical wear and chip forms of these materials. How does the FP4 chipbreaker affect surface finish? The FP4 chipbreaker promotes short, controllable chips and stable cutting conditions, which helps to maintain consistent surface quality and reduces the likelihood of built-up edge on the insert. Can this insert be used for interrupted cuts? Yes, the rhombic 80° geometry and 0.4 mm corner radius provide a robust cutting edge suitable for light to moderate interruptions common in turning operations. What does the CCMT designation mean? CCMT indicates a negative rhombic insert with an 80° included angle and a top relief suitable for conventional turning toolholders; CCMT09T304-FP4 describes the specific geometry, size and chipbreaker combination. Is the insert compatible with standard toolholders? The T3 plate thickness and tolerance class M align the insert with commonly available negative insert toolholders, ensuring secure seating and repeatable positioning. Manufacturer/Responsible: Walter Tools; Derendinger Straße 53; 72072 Tübingen; Germany. The Walter AG (brand appearance: Walter Tools) is among the world’s leading manufacturers of precision tools for metalworking and is part of the Sandvik Group. Protected trademarks and trade names belong to their respective owners. Brand names and trademarks are mentioned for explanation only and indicate no affiliation between our company and the mentioned manufacturers. The item offered is an original, factory-new product of the manufacturer.
CCMT09T304-FP4 WPP10G Wendeplatten - Walter Tools
Benefit from the combination of Tiger·tec Gold coating and a precisely engineered FP4 chipbreaker for consistent performance in steel machining; the robust rhombic geometry and 0.4 mm corner radius ensure steady surface quality and predictable tool life. Order the CCMT09T304-FP4 WPP10G directly via Metav Werkzeuge or consult our advisors for application support. CCMT09T304-FP4 WPP10G Rhombic 80° indexable insert, Tiger·tec Gold – Walter Tools The CCMT09T304-FP4 WPP10G is a rhombic 80° indexable insert with a 0.4 mm corner radius, optimised for turning and boring operations in steels and designed for robust chip control and long tool life Tiger·tec Gold coated for extended life FP4 chipbreaker for stable chip control Rhombic 80° form for versatile turning and boring Designed for steel machining (ISO P) Consistent performance for steel applications The combination of Tiger·tec Gold coating and a coated carbide substrate delivers improved wear resistance and thermal stability when machining steels. Designed for the ISO P material group, this insert minimises flank wear under typical steel cutting temperatures and supports longer tool life and fewer interruptions for tool changes. The result is higher uptime and more predictable component quality in batch and single‑piece production. Geometry and chip control that raise productivity A Rhombic 80° form with a 7° clearance angle and 0.4 mm corner radius provides a robust cutting edge suited to a range of turning depths. The FP4 chipbreaker is engineered to form short, controlled chips across common turning conditions, reducing the risk of chip entanglement and improving surface finish. For practical terms: the chipbreaker’s geometry influences how the material is split and evacuated, which in turn reduces cutting forces and stabilises the process. Practical handling and workshop benefits The CCMT09T304-FP4 WPP10G insert is an indexable solution that reduces changeover time and supports repeatable machining cycles. Its T3 thickness and standard CCMT form make it compatible with widely used insert holders, enabling quick replacement and simple inventory management. For smaller workshops and production departments, the predictable wear behaviour and reliable chip control translate into lower process variability and easier planning of tool life and maintenance intervals. For reliable high‑performance turning with Walter Tools’ Tiger·tec Gold grade, contact Metav Werkzeuge for ordering and technical advice via info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: CCMT09T304-FP4-WPP10G-WALTER Designation: CCMT09T304-FP4 WPP10G Type: Drilling/boring and turning indexable insert Manufacturer: Walter Tools Facts Insert size: 09 Plate form: Rhombus 80° Clearance angle: 7° Corner radius: 0.4 mm Thickness: T3 Tolerance class: M Special features Coating: Tiger·tec Gold (coated carbide) Grade: WPP10G (for steel, ISO P) Chipbreaker: FP4 Series: Tiger‑tec Gold Execution: T FAQ What materials is this insert suited for? The CCMT09T304-FP4 WPP10G is specified for steels (ISO P); the WPP10G grade and Tiger·tec Gold coating are optimised for common unalloyed and alloyed steels. How does the FP4 chipbreaker affect machining? The FP4 chipbreaker on this insert promotes short, controlled chips and reliable evacuation, which improves surface finish and reduces chip‑related interruptions during turning and boring. Is the geometry suitable for both turning and boring operations? Yes, the rhombic 80° form and 7° clearance make the insert versatile for a range of turning and light to medium boring applications, offering a balance between strength and accessibility. What does the 0.4 mm corner radius provide in practice? A 0.4 mm corner radius increases edge robustness for interrupted cuts and helps maintain surface integrity while allowing acceptable feed rates for finishing and semi‑finishing passes. Can this insert be used with standard CCMT holders? The insert follows the common CCMT form and the T3 thickness, making it compatible with standard holders designed for CCMT indexable inserts. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Protected trademarks and trade names are the property of their respective owners. Brand names and registered trademarks are mentioned solely for explanatory purposes. There is no connection between our company and the mentioned brands. The offered item is an original, factory‑new product of the manufacturer.
CCMT09T304-FP4 WPP20G FP4 Wendeplatten - Walter Tools
Take advantage of the combination of high process reliability and optimised chip control for consistent productivity; the Tiger·tec Gold coating and FP4 chipbreaker ensure longer tool life and secure chip evacuation. Order the inserts directly via Metav Werkzeuge or contact the consultants for application advice. CCMT09T304-FP4 WPP20G — Turning indexable insert for steel (Walter Tools) The CCMT09T304-FP4 WPP20G is a coated turning insert designed for reliable machining of steel components in production environments. Tiger·tec Gold coating for extended tool life Optimised FP4 chipbreaker for stable chip control Suitable for ISO P (steel) machining 0.4 mm corner radius for versatile finish Consistent cutting performance that boosts productivity The combination of a Tiger·tec Gold coating and coated carbide substrate delivers a balanced mix of wear resistance and toughness, which translates into predictable tool life and fewer insert changes. The proven coating technology reduces flank wear under the typical heat and abrasion from steel turning, so cycle times remain steady and setup frequency is reduced. This results in improved process efficiency and lower downtime during series production. Geometry and chip control for secure machining The FP4 chipbreaker has been developed to promote controlled chip formation in a wide range of cutting conditions. Paired with the rhombic 80° geometry and a 0.4 mm corner radius, the insert supports stable cutting forces and manageable chip shapes, lowering the risk of surface damage and machine interruptions. The combination of chip control and insert geometry simplifies process planning and reduces the need for secondary operations to correct poor finishes. Application-focused design for steel machining Classified for ISO P materials, this grade is optimised for unalloyed and alloyed steel where typical heat generation and chip behaviour occur. The moderate clearance of 7° and the insert form support both finishing and medium-depth turning operations, allowing a single insert style to cover several machining steps. This flexibility reduces inventory complexity while maintaining surface quality and dimensional accuracy. Reliable choice for production and mixed-batch work With the WPP20G grade and the Tiger·tec Gold series background, the insert offers a reliable compromise between wear resistance and edge robustness. In practice this means fewer insert breakages under variable cutting conditions and more predictable tool life for mixed-batch manufacturing. The result is a smoother production flow, easier planning of tool changes and an overall reduction in process variability. Speak to Metav Werkzeuge for tailored application advice on Walter Tools Tiger·tec Gold inserts and arrange a supply via info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: CCMT09T304-FP4-WPP20G-WALTER Designation: CCMT09T304-FP4 WPP20G Label: Bohr-/Aufbohrwendeschneidplatte / Drehwendeschneidplatte CCMT09T304-FP4 WPP20G Walter Tools Manufacturer: Walter Tools Core data Clearance angle: 7° Corner radius: 0.4 mm Plate size: 09 Plate thickness: T3 Tolerance class: M Special features Coating: Tiger·tec Gold Grade: WPP20G (coated carbide) Chipbreaker: FP4 Plate form: Rhombus 80° Application: Steel (ISO P) Series: Tiger·tec Gold FAQ What materials is this insert designed for? The CCMT09T304-FP4 WPP20G is specified for ISO P materials and is particularly suited to machining unalloyed and alloyed steel. How does the Tiger·tec Gold coating benefit production runs? The Tiger·tec Gold coating on this Walter Tools grade enhances wear resistance and improves routine performance, leading to longer intervals between insert changes and more consistent batch outputs. Which chip behaviour can be expected with the FP4 chipbreaker? The FP4 chipbreaker produces controlled, manageable chips across common turning parameters, improving process safety and reducing the likelihood of chip-related machine stoppages. Is the insert suitable for finishing and medium-depth cuts? Yes. The combination of a 0.4 mm corner radius and rhombic 80° geometry makes the insert versatile for finishing and medium-depth turning tasks while maintaining good surface quality. Can this insert reduce inventory complexity in mixed-production shops? Using the WPP20G grade with the FP4 chipbreaker allows coverage of multiple turning operations with a single insert type, helping to lower inventory variants and simplify tooling logistics. Manufacturer/Responsible: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen; Germany; Protected trademarks and product names remain the property of their respective owners. Brand names and protected product names are used solely for explanatory purposes. There is no commercial affiliation between our company and the mentioned brands. The item offered is an original, factory-new product from the manufacturer.
Why indexable inserts are indispensable in modern machining
Indexable inserts, also known as cutting inserts or indexable cutting inserts, are standardised, replaceable cutting elements that mount on tool holders such as turning bits, milling cutters or drills. Made from wear-resistant materials like carbide, cermet, ceramic or other superhard grades, they carry the actual cutting edge and allow a worn corner to be rotated or flipped instead of replacing or regrinding the entire tool body.
How these inserts work and when to choose them
In everyday workshop and production settings, indexable inserts perform the direct material removal on the workpiece. Standard inserts for tool systems without internal coolant typically feature closed faces or a single central fixing hole, with heat evacuation handled by external machine nozzles. Inserts designed for systems with internal coolant are engineered to support coolant flow: they include calculated chipbreaker geometries that guide an internal coolant jet under the chip or, in specialised designs, contain sintered microchannels to direct coolant right to the cutting edge. Such coolant-compatible inserts are essential for machining heat-resistant alloys, heavy cutting operations and deep internal machining, where thermal load and chip control are critical.
Tangible benefits for production and workshop efficiency
Choosing the right indexable inserts delivers measurable operational advantages:
- Reduced downtime: faster changeover because a worn insert is simply indexed rather than the whole tool being replaced.
- Extended cutting-edge life: targeted coolant application and optimised chipbreaker design lower thermal stress and improve tool life.
- Consistent part quality: predictable cutting-edge geometry from standardised inserts maintains tolerances across batches.
- Versatility: availability in carbide, cermet, ceramic and superhard grades permits selection according to workpiece material and cutting conditions.
- Lower tooling costs over time: fewer full-tool replacements and less regrinding required.
Metav as a dependable source for inserts and tooling systems
Metav combines decades of precision expertise with a wide-ranging supply chain, positioning itself as a practical partner for industry, craft and trade. From Emmerich on the Rhine, Metav operates as a quality filter for the European market, offering more than 250,000 products and serving over 48,000 customers. For procurement teams aiming to reduce supplier count while retaining technical reliability, Metav’s assortment of indexable inserts and compatible tool holders provides a central, trustworthy solution.
Quick summary
Indexable inserts (cutting inserts or indexable cutting inserts) enable economical, repeatable material removal by allowing worn cutting edges to be indexed or replaced quickly; coolant-adapted designs further reduce thermal load and enhance chip control for demanding applications.
FAQ
What materials are indexable inserts available in?
Indexable inserts are available in wear-resistant grades such as carbide, cermet, ceramic and other superhard materials, selected according to the workpiece material and cutting conditions.
When should I choose inserts with internal coolant support?
Choose inserts designed for internal coolant when machining heat-resistant alloys, performing heavy cuts or working in deep internal features, because the coolant reduces thermal load at the cutting edge and actively improves chip breakage.
How do chipbreaker geometries affect performance?
Chipbreaker geometries on indexable inserts guide the chip flow and, when matched to an internal coolant jet, direct the coolant under the chip to control temperature and facilitate reliable chip formation, which extends edge life and stabilises machining.
Can standard inserts be used with external coolant only?
Yes; standard inserts for tool systems without internal coolant typically have closed faces or a central fixing hole and rely on external machine nozzles for heat evacuation, which is sufficient for many routine, accessible cuts.
Why source inserts through Metav?
Metav supplies a broad range of indexable inserts and tooling, backed by decades of expertise and a comprehensive European stock, making it a practical choice for consistent quality and dependable delivery.
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com