Precision marking tools for accurate setup and machining
Precision marking tools such as scribing sets and scribers are essential for laying out work in metalworking and woodworking, enabling machinists and fitters to transfer exact lines and points for drilling, milling and cutting. These tools serve to produce fine reference lines on materials like metal, wood and plastic, ensuring correct alignment and repeatable results when combined with a precision caliper or other measuring aids. Using a quality scriber, scribing set and precision caliper improves setup speed, reduces setup errors and supports consistent tolerances across batches.
150mm Slip Gauge Stainless Hardened And Ground Lapped Measuring Edges Matt Finish Hand Heat Shield - TECWERK
Take advantage of a precision tool that combines hardened stainless steel construction, lapped measuring edges and a compact 150 mm length for reliable straightness and alignment checks in workshop metrology; order the hairline straight edge directly via Metav Werkzeuge or ask our consultants for application advice. Hairline straight edge DIN 874/00 L 150 mm — hardened stainless steel, lapped measuring edges (TECWERK) A hairline straight edge DIN 874/00 L 150 mm is designed for precise straightness checks, alignment and reference work in machine shops and inspection benches Hardened and ground stainless steel Lapped measuring edges for high accuracy Hand‑heat protection on the grip Non‑glare matt finish and inspection required Accuracy that secures repeatable measurement results Constructed from stainless steel that is hardened and ground, this hairline straight edge delivers a stable reference surface for inspection tasks and alignment routines. The lapped measuring edges reduce local deviations and allow consistent comparison against machine beds, gauges or workpieces, improving overall accuracy in set‑up and verification. At a working length of 150 mm, the device fits inspection benches and toolmakers’ benches where space is limited but measurement reliability is critical. Ergonomics and surface treatment for everyday workshop use A matt, non‑glare finish and an integrated hand‑heat protection zone minimise thermal transfer and visual interference during handling, making the tool comfortable for repeated use in production and maintenance environments. The compact cross‑section of 28 x 6 mm provides a rigid profile without excessive mass, aiding swift positioning and reducing handling fatigue. For applications that demand quick visual checks and precise contact measurements, this design speeds up workflows while maintaining a professional feel. Traceability and compliance for dependable inspection routines The straight edge is produced to the DIN 874/00 concept and is inspection required, which supports documented quality procedures and traceable acceptance in quality control chains. Regular verification of the reference surface preserves long‑term performance and ensures that alignment results remain within tolerances. For workshops seeking to integrate the tool into controlled inspection plans, the recorded condition after verification maintains confidence in repeated measurements and process stability. Contact Metav Werkzeuge for tailored technical advice on TECWERK straight edges and to confirm stock and inspection status at our Emmerich location — email info@metav-werkzeuge.com or call +49 2822 7131930 Technical Data Article number: 2000858393NW Label: Haarlineal DIN 874/00 L.150mm Spezialstahl Q.28x6mm TECWERK Product type: Hairline straight edge Manufacturer: TECWERK Length: 150 mm Cross-section: 28 x 6 mm Packaging unit: 1 Facts Length: 150 mm Cross-section: 28 x 6 mm Packaging unit: 1 Special features Material: stainless steel Hardened and ground Lapped measuring edges Hand‑heat protection Non‑glare matt finish Inspection required FAQ What applications is this straight edge best suited for? This hairline straight edge is intended for straightness checks, alignment and reference comparisons in machine shops, inspection benches and assembly tasks where a compact precision reference is required. How is accuracy ensured for this product (SKU 2000858393NW)? Accuracy is achieved through hardened and ground construction and lapped measuring edges; the item is marked as inspection required to support traceable verification. Can the tool be used on sensitive surfaces without scratching? The lapped edges provide a fine contact surface suitable for careful comparison work; proper handling and clean contact surfaces are recommended to avoid abrasion. Is thermal influence reduced during handling? Yes, the integrated hand‑heat protection feature reduces heat transfer from the operator’s hand, limiting thermal influence on short measurement tasks. Which standard does the straight edge relate to? The product follows the DIN 874/00 concept for hairline straight edges commonly used in precision inspection and alignment tasks. Manufacturer / Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund
150mm Stainless Steel Flexible Rule Graduated 1/2mm, Laser Marked - TECWERK
Take advantage of a 150 mm measuring length combined with a lasered, dual graduation for quick, reliable linear checks; the flexible, stainless spring strip steel construction ensures corrosion resistance and simple handling. Order the stainless steel rule directly via Metav Werkzeuge or ask the consultants for application advice. TECWERK Steel Rule L 150 mm — flexible stainless measuring rule with lasered mm / 0.5 mm graduation TECWERK Steel Rule L 150 mm is a compact, flexible measuring strip designed for precise linear checks in workshops and production environments 150 mm length for compact measurements Dual graduation mm / 0.5 mm for fine reading Lasered scale for durable visibility Flexible stainless spring strip for corrosion resistance Precise readings in a compact format The 150 mm measuring strip offers a concise solution when space is limited but accurate linear information is required. The lasered scale provides crisp, abrasion-resistant graduations that remain legible over time; the mm / 0.5 mm graduation (division B) enables both coarse and finer estimations without additional tools. This combination supports efficient in-process checks and reduces the need for frequent instrument changes, helping to maintain steady workflow and minimise handling time in routine measurement tasks. Robust, flexible construction for everyday use Constructed from stainless spring strip steel, the measuring strip combines corrosion resistance with the resilience necessary for repeated bending and storage. The nominal cross-section of 13 x 0.5 mm gives a stable feel while remaining pliable enough to follow gentle contours, making it suitable for measuring shallow curves or confined features where rigid rulers are impractical. The flexible design also supports safe storage in tool rolls or pockets, reducing the risk of permanent deformation and lowering lifetime maintenance. Conformity, inspection and traceability for quality workflows Marked as inspection required, the rule meets expectations for measurable traceability within quality-controlled environments; this status supports integration into calibrated inspection routines when needed. The compact format and clear markings allow straightforward documentation of checks, and the durable construction reduces wear-related variance. The SKU 2000858760NW identifies the exact item for procurement and stock management, streamlining ordering and inventory processes for production and maintenance teams. For availability, specification confirmation or to request tailored advice on TECWERK flexible steel rules, contact Metav Werkzeuge in Emmerich — the partner for precise, dependable workshop supplies Technical Data Article number: 2000858760NW Label: Stahlmaßstab L.150mm rostfr.STA biegsam Teilung B=mm/1/2mm TECWERK Manufacturer: TECWERK Facts Length: 150 mm Cross-section: 13 x 0.5 mm Graduation: mm / 0.5 mm Packaging unit: 1 Special features Lasered scale Flexible execution Material: stainless spring strip steel Inspection required FAQ What material is the measuring rule made from? The TECWERK steel rule is manufactured from stainless spring strip steel, which provides corrosion resistance and reliable spring-back. Can the rule measure small radii and curved surfaces? Yes, the flexible construction allows the measuring strip to follow gentle curves, making the steel rule suitable for shallow curved surfaces. How fine is the scale on this rule? The lasered scale features a dual graduation of mm and 0.5 mm (division B), giving options for both standard and finer readings on the TECWERK measuring strip. Is this item suitable for use in quality control processes? The product is marked as inspection required, which supports its use in traceable quality-control workflows; refer to SKU 2000858760NW for procurement and documentation. Will the scale markings wear off quickly? The scale is lasered for abrasion resistance, which prolongs legibility compared with printed markings and supports long-term use. Manufacturer / Responsible: NORDWEST Handel AG, Robert-Schuman-Straße 17, 44263 Dortmund
150mm Steel Scale Flexible Spring Steel With Polyamide Coating, 1mm Graduation - Bayerische Maß-Industrie Arno Keller GmbH
Take advantage of a flexible spring-steel construction and a polyamide protective cover for clear readings and reliable wear resistance; order directly via Metav Werkzeuge or ask our consultants for complementary measuring equipment. ISOFLEX Steel Scale L 150 mm — flexible steel rule with polyamide cover The ISOFLEX steel scale is a flexible measuring rule designed for precise linear measurement in workshops and inspection environments, combining a spring-steel core with a protective polyamide sheath. Flexible spring-steel scale with polyamide coating Clear 1 mm graduation for precise reading High wear resistance for long service life Factory-inspection required for traceable accuracy Durable accuracy for everyday workshop measurement The flexible construction is based on a spring-steel core, offering resilience against bending while maintaining reliable flatness when laid on a workpiece. The polyamide protective cover improves surface resistance and reduces abrasion, which preserves the 1 mm graduation for longer. With a nominal length of 150 mm and a compact cross-section of 13 x 0.3 mm, the scale suits routine measuring tasks where repeatable, visible marks are necessary. The material choice and design support consistent readings and reduce the need for frequent replacement, improving process stability in small-series production and maintenance work. Reliable performance and documented conformity This steel rule is declared inspection required, indicating that it is supplied and managed under traceable verification procedures. The execution is flexible, making it suited for measurement of slightly curved surfaces and close-tolerance checks on components. Readability is emphasised by clear division lines and contrast, which speeds measurement cycles and reduces handling time. For workshops that depend on trustworthy measuring tools, the combination of durability and documented conformity supports efficiency and reduces the likelihood of rework. For additional calibration details or trace certificates, Metav Werkzeuge can provide the necessary information. Compact format that simplifies handling and storage A slim cross-section of 13 x 0.3 mm keeps the rule lightweight and easy to position in jigs or along edges, yet robust enough to withstand regular workshop use. The compact 150 mm length allows straightforward storage in tool drawers and easy transport between workstations. The flexible profile helps protect the scale from permanent deformation during incidental knocks, while the protective covering contributes to a tactile grip and easier visual alignment. When combined with routine inspection and correct handling, this format offers a practical balance between precision and everyday usability. For reliable, democratised precision in every workshop, contact Metav Werkzeuge to discuss the ISOFLEX steel scale and matching measuring accessories — call +49 2822 7131930 or email info@metav-werkzeuge.com Technical data SKU: 8000446859NW Item: ISOFLEX steel scale, flexible, polyamide-covered Type: Steel scale Length: 150 mm Cross-section: 13 x 0.3 mm Packing unit: 1 UID: 8000446859NW Facts Length: 150 mm Graduation: 1 mm Cross-section: 13 x 0.3 mm Special features Flexible spring-steel construction Polyamide protective cover Excellent readability High wear protection Execution: flexible Inspection required (prüfpflichtig: yes) FAQ What is the main material of this scale and how does it affect use? The ISOFLEX steel scale is made from flexible spring steel with a polyamide protective cover; the combination yields resilience against bending and enhanced surface wear protection for durable readings. What graduation is marked on the rule? The rule features a clear 1 mm graduation, enabling straightforward visual measurement for routine workshop tasks and small-component checks. Is the scale suitable for measuring slightly curved surfaces? Yes, the flexible design permits secure placement on slightly curved edges while still allowing precise linear readings. How does the polyamide cover contribute to performance? The polyamide sheath increases abrasion resistance and maintains legibility of the scale markings, extending usable life under regular workshop conditions. Is this item subject to inspection or certification? This steel rule is marked as inspection required; customers can request traceable verification details from Metav Werkzeuge if certificate information is needed. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
150x130 mm Centre Square Matt Chrome Plated, 0.3 kg - Metav IndustryLine
Take advantage of a precision reference edge, tool‑steel construction and a matt chrome finish for glare‑reduced readings and enduring workshop use; procure the centring square directly via Metav Werkzeuge or consult the Metav team for application advice. Centring square M214.171 – 150 x 130 mm, matt chrome‑plated (Metav IndustryLine) The centring square M214.171 is a compact right‑angle layout tool for accurate alignment and marking tasks in metalworking and general workshop layout. Matt chrome finish for low glare Robust tool‑steel construction Compact 150 x 130 mm format Accurate alignment for layout and set‑up The right‑angle reference plate offers a reliable datum for marking and checking parts during set‑up and layout work. Built from tool steel with a matt chrome finish, the device reduces reflections when reading scribed lines and maintains a true edge under regular workshop use. The compact format provides a balanced combination of stiffness and accessibility for confined machining or assembly stations, making it a practical choice for repetitive alignment tasks. Designed for repeatable positioning and workshop workflow With its defined leg lengths, the square serves as a reproducible reference for transferring centres and checking perpendicularity on components and assemblies. The matt chrome surface improves visual contrast when comparing scribed marks, while the rust‑protected treatment preserves the reference geometry. As a straightforward layout instrument, it supports efficient process flows in both small‑batch and series environments by reducing rework caused by misalignment. Durable build and broad application range Manufactured to withstand everyday use, the square's tool‑steel body offers long service life and dependable performance in marking, centring and inspection tasks. It is suitable for use with shafts and cylindrical components where a precise right angle is required; the item is compatible with shafts up to Ø190 mm for centring operations. The construction focuses on robustness and a consistent reference surface rather than decorative detail, ensuring the tool remains a practical asset across workshops and maintenance departments. Contact Metav Werkzeuge for tailored technical advice, application recommendations or to request a procurement quote for the Metav IndustryLine centring square M214.171 Technical data Article number: M214.171 GTIN: 4054469106991 TARIC code: 90172039 ECLASS: 21170131 Facts Dimensions: 150 x 130 mm Compatible shaft diameter: Ø190 mm Materials & features Tool steel Rust‑protected Matt chrome‑plated finish Category: Anreisszeuge (layout tools) FAQ What materials is the centring square made from? The centring square M214.171 is made from tool steel with a rust‑protected, matt chrome finish. Which dimensions does the instrument offer? The device is supplied in a compact 150 x 130 mm format suitable for general layout and workshop use. Can the square be used with shafts and cylindrical parts? Yes, the M214.171 is suitable for centring and alignment tasks with shafts up to Ø190 mm. How does the matt chrome finish benefit workshop use? The matt chrome finish reduces glare and improves contrast when reading scribed marks, aiding repeatable visual comparison during marking and inspection. Is this item part of the Metav IndustryLine range? Yes, the M214.171 is offered under the Metav IndustryLine series and can be sourced directly from Metav Werkzeuge. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
150×130 mm Centre Square Aluminium Alloy, Black Anodised, For Ø190 mm Shafts - Metav IndustryLine
Take advantage of a lightweight, hardened aluminium design paired with a black anodised finish to secure repeatable centre marking on shafts and cylindrical components; the compact 150 x 130 mm geometry supports efficient workshop workflows. Order the centre square directly via Metav Werkzeuge or consult the Metav team for application advice. Zentrierwinkel AL 150 x 130 mm — centre square, hardened aluminium, black anodised (Metav IndustryLine) The Zentrierwinkel AL 150 x 130 mm is a compact centre square designed for precise marking and alignment tasks in general workshop and metalworking applications, optimised for shafts and cylindrical workpieces. Hardened aluminium alloy construction Black anodised corrosion-resistant finish Compact 150 x 130 mm centring geometry Lightweight 0.2 kg for easy handling Accuracy and repeatability for routine centring tasks The compact centring tool delivers a stable reference for fast, repeatable centre marking on cylindrical parts. Machined from a hardened aluminium alloy and finished with black anodising, the device combines corrosion resistance with low thermal mass to reduce dimensional drift during handling. The 150 x 130 mm geometry places the tool squarely in the standard measurement range, which balances reach and rigidity for everyday tasks in machine shops and maintenance departments. As a result, marking and setup times are shortened, boosting workshop productivity while maintaining the quality of alignment operations. Designed for shaft work and easy handling With a low weight of 0.2 kg and a compact footprint, this centre square is tailored for fast positioning on rotated or stationary shafts up to Ø190 mm, providing a reliable datum for scribing or punch marking. The lightweight construction eases one-handed handling and repeated repositioning, while the hardened alloy resists wear at contact edges. The combination of ergonomics and durable material reduces operator fatigue and keeps throughput steady during repetitive tasks, making it a practical choice for engineers and fitters who require both speed and dependable performance. Practical benefits for the workshop and quality control The robust surface treatment and solid manufacture support frequent use in workshop environments where resilience to knocks and light contamination is needed. As a marking aid, the tool simplifies transfer of centrelines and alignment references from chucks or fixtures to components, improving the interface between setup and machining. The compact design also stores conveniently in tool trolleys or instrument drawers, helping to keep jobsite organisation tight and saving time during changeovers. For reliable centre marking with the Metav IndustryLine centring square, contact Metav Werkzeuge for technical guidance and ordering support — Metav’s specialists in Emmerich can advise on suitability for specific shaft diameters and workshop workflows. Technical Data SKU: M214.171.AL GTIN: 4054469164489 Customs tariff number: 90172039 Category: Anreisszeuge (marking/centre tools) Facts Measurement range: 150 x 130 mm Weight: 0.2 kg Suitable for shafts up to Ø190 mm Material: aluminium alloy, hardened Special features Surface: black anodised Compact centre square geometry for marking and alignment Lightweight design for easy handling and storage Intended for workshop marking and setup tasks FAQ What is the effective measurement range of this centre square? The centre square offers a 150 x 130 mm geometry, categorised in the standard measurement range suitable for general machine‑shop and metalworking tasks. Which materials is the tool made from? This centring tool is made from a hardened aluminium alloy with a black anodised finish, combining lightness with surface protection. Can the device be used on shafts with a diameter of 190 mm? Yes, the design is suitable for use with shafts up to Ø190 mm and provides a stable reference for centre marking on such cylindrical parts. How does the black anodised surface help in workshop use? The black anodising increases corrosion resistance and reduces glare, helping to preserve the visible edges used for marking while improving long‑term durability. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
160 mm Scriber With Solid Carbide Tip, Hardened Point - Metav IndustryLine
Take advantage of the combination of durable carbide tip and compact 160 mm format for reliable, repeatable marking in workshop routines; the robust construction and low weight ensure steady handling and minimal fatigue. Order the tool directly via Metav Werkzeuge or ask the consultants for detailed specifications if required. M214.033 scriber with carbide tip – 160 mm marking tool (Metav IndustryLine) The M214.033 scriber is a compact, carbide‑tipped marking needle designed for precise layout and scribing tasks in workshop environments, offering a consistent line quality across routine marking operations. Carbide tip for durable, sharp marking Compact 160 mm overall length Lightweight 40 g for comfortable handling Robust construction for workshop use Accurate lines through a carbide tip for consistent layout The supplied carbide tip provides a fine, wear‑resistant point that keeps a consistent edge over prolonged use, enabling precision marking where repeatability matters. In practical terms, the 160 mm overall length balances reach with control: the short form factor helps to reduce flex and improve stability when scribing small to medium workpieces. For production workflows this means less rework and clearer reference lines for machining or assembly operations, supporting faster, more reliable preparation of parts. Built for comfortable, fatigue‑free handling during repetitive use At just 0.04 kg (40 g), the instrument is lightweight, making extended marking sessions noticeably less tiring and contributing to steadier hands and finer results. The straightforward, robust construction minimises moving parts and maintenance needs, which is an advantage in busy shops where simple, dependable tools keep processes running. The durable tip material reduces downtime for sharpening or replacement, which translates into a small but tangible efficiency gain across many marking cycles. Practical choice for general workshop marking and layout As a classic marking tool, the needle is suited to routine layout, centre punching guidance and transfer lines on a variety of surfaces where a carbide point is appropriate. The straightforward specification makes it easy to integrate into existing tool kits and layout stations, and the compact format suits both bench use and mobile inspection tasks. For buyers seeking dependable, low‑complexity marking implements, this model offers a direct combination of durability and handling comfort that supports everyday precision. Contact Metav Werkzeuge for tailored advice on the Metav IndustryLine M214.033 carbide scriber and for delivery options from Emmerich Technical data SKU: M214.033 GTIN: 4054469106267 Label: Reißnadel, HM, 160 mm mit HM‑Spitze, 160 mm ECLASS: 21049238 Tariff number: 90172039 Dimensions & weight Length: 160 mm Weight: 0.04 kg Materials & features Carbide tip (HM) Category: Marking tools (Anreisszeuge) FAQ What is the exact length and weight of the scriber? The M214.033 scriber has an overall length of 160 mm and a weight of 0.04 kg (40 g), making it compact and easy to handle. What material is used for the tip and what benefit does it provide? The needle is fitted with a carbide (HM) tip, which offers a hard, wear‑resistant point for sustained sharp marking and longer service life. Is the marking tool suited to repetitive workshop use? Yes, the combination of a durable carbide tip and lightweight construction supports repetitive marking tasks with reduced fatigue and consistent line quality. Does the specification state whether the tip is replaceable? The available specification confirms a carbide tip but does not state whether the tip is replaceable; the product is supplied with the carbide point as described. Which category does this tool belong to for workshop classification? This item is listed under marking tools (Anreisszeuge) and is intended for layout and scribing applications in general workshop environments. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
160mm Precision Scratch Caliper T-Form, 100mm Stop, Hardened Chrome-Plated Steel, Delivered in Case - Metav IndustryLine
Benefit from a hardened special‑steel construction and a T‑form layout with a 100 mm stop for repeatable scribing and marking. The mechanical vernier with a fine‑adjustment spindle provides a 0.05 mm readability that supports consistent setup and faster job changeovers. Order the instrument directly via Metav Werkzeuge or consult our advisors for application support. M201.140 Precision Scribing Caliper — 160 mm T‑form with 100 mm stop (Metav IndustryLine) The M201.140 is a T‑form precision scribing caliper designed for layout and marking tasks in metalworking, jig production and toolroom set‑ups. T‑form design for precise scribing Hardened special steel, matt chrome finish Fine‑adjustment spindle for exact positioning Repeatable marking with a T‑form layout for standard workshop tasks The T‑form layout together with a robust bridge measuring 100 mm gives a stable contact point for repeated scribing and marking operations. Built from hardened special steel with a matt chrome finish, the instrument resists wear and retains a clear datum over many cycles. With a measuring range of 0–160 mm, the caliper falls into the Standard class of workshop calipers and thus offers the best compromise between reach, stiffness and one‑hand handling for everyday metalworking and machine‑shop tasks. The combination of a rigid T‑form and a defined stop shortens set‑up time when multiple identical marks are required. Precision control and industrial‑grade readability for setup accuracy A mechanical vernier with a reading of 0.05 mm gives industrial‑standard resolution for layout and control work; it is suited to production environments where quick visual confirmation is needed rather than submicron measurement. The integrated fine‑adjustment spindle enables gentle, controlled movements when positioning the scribing jaw, which reduces error introduced by manual thrust. For operations such as marking datum lines, transferring offsets to a workpiece or pre‑setting tools, this layout and control system increases throughput while maintaining reproducible results. Easy interpretation and practical guidance for non‑specialists The analogue vernier is straightforward to use: the main scale gives the rough value and the vernier index refines it to 0.05 mm increments—sufficient for workshop layout and pre‑machining checks. The fine‑adjustment spindle facilitates single‑turn micro‑movements to align the scribe precisely before marking. For users less familiar with vernier calipers, this instrument combines familiar mechanical feel with clear graduations to reduce training time and to integrate smoothly into existing inspection routines. Robust design reduces downtime and simplifies maintenance Surface treatment and material selection emphasise longevity: the hardened body and matt chrome plating limit corrosion and reduce glare without affecting sliding accuracy. The simple mechanical construction is easy to clean and inspect; wear points can be checked visually and corrected through routine adjustment rather than replacement. Metav’s role as a European quality filter amplifies these benefits: consistent component selection and stock control mean reliably similar tools across the workshop fleet, which helps to standardise measurement practice and reduces calibration complexity. Choose the Metav IndustryLine M201.140 T‑form precision scribing caliper for workshop‑ready accuracy and contact Metav Werkzeuge for application advice or specification support at info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: M201.140 GTIN: 4054469100708 Customs tariff number: 90173000 Category: Calipers Brand: Metav IndustryLine Facts Measuring range: 0–160 mm Readability: 0.05 mm Bridge/stop: 100 mm Analog: mechanical vernier eClass: 21170344 Special features Material: special steel, hardened, matt chrome‑plated T‑form layout for scribing Fine‑adjustment spindle Mechanical construction for layout and marking tasks FAQ How precise is the M201.140 for typical workshop layout tasks? The M201.140 precision scribing caliper by Metav IndustryLine provides a readability of 0.05 mm, which is the industrial standard for many marking and setup operations and supports reproducible layout work. For which applications is the T‑form design most suitable? The T‑form caliper is ideal for repeatable scribing and marking, fixture set‑up and tool pre‑setting where a stable reference and a defined bridge (100 mm stop) speed up repeated operations in the machine shop. Does the M201.140 include fine‑adjustment for delicate positioning? Yes—this caliper features a fine‑adjustment spindle that enables controlled micro‑movements for precise alignment of the scribing jaw before marking. What materials and surface treatment are used in this instrument? The instrument is manufactured from hardened special steel and finished with a matt chrome plating to improve wear resistance and reduce reflection during use. Is the 160 mm range suitable for general mechanical workshops? A 0–160 mm measuring range places this instrument in the Standard class, offering a practical balance of reach and stiffness for everyday metalworking and toolroom measurements. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
160mm Scriber Caliper 0.05mm Resolution With 135mm Stop - TECWERK
Benefit from a compact marking tool that combines a 160 mm measuring range with 0.05 mm readability and a 135 mm fixed stop for consistent scribing — ideal for repeatable layout work. Order the scribing caliper directly via Metav Werkzeuge or ask our consultants if additional information is required. Scribing Caliper 160 mm H.PREISSER — 0.05 mm Readability, 135 mm Stop The Scribing Caliper 160 mm H.PREISSER is a workshop marking and measuring instrument designed for precise layout tasks in metalworking and fabrication. 160 mm measurement range 0.05 mm reading accuracy 135 mm fixed stop length Robust marking and measuring tool Reliable precision for repeatable layout work The scribing caliper delivers a clear 160 mm measuring span with a fine 0.05 mm readability, ensuring repeatable scribing and layout measurements on components. The finely graduated scale and rigid guide enable controlled marking steps, reducing rework and saving machining time. For less experienced users, the scale’s clarity translates into measurable process improvement: fewer adjustments on the machine and more consistent first-pass results. The tool’s role in the workflow is to provide stable reference lines that translate directly into accurate finishing operations. Consistent marks with a defined stop length Equipped with a dedicated stop of 135 mm, the instrument produces identical offsets quickly and without additional fixtures. The fixed stop is particularly useful in small-batch production and jig preparation, where identical reference points are required across multiple parts. By standardising the marking distance, the caliper helps to shorten setup times and to lower scrap rates, which improves throughput and cost-efficiency in everyday workshop use. The integrated stop encourages a disciplined marking routine that benefits both speed and quality. Designed for practical workshop use and low maintenance Built for routine use in a workshop environment, the scribing caliper focuses on straightforward operation and longevity. The compact form supports one-handed handling during line marking, while the mechanical design minimises play for accurate results. Routine cleaning and occasional light lubrication of sliding surfaces maintain performance; no complex servicing is required. The tool is therefore a pragmatic choice where steady availability of a precise marking device is needed to keep production moving. Where this caliper enhances process reliability In toolrooms and fabrication benches the Scribing Caliper 160 mm H.PREISSER serves as a trusted layout instrument that bridges measurement and machining. Its combination of repeatable stop positioning and fine readability reduces variance between marking and machining stages, supporting higher first-pass yields. For teams aiming to streamline marking operations, the caliper delivers predictable outcomes that feed into faster downstream processes and steadier quality control. Metav Werkzeuge’s emphasis on accessible precision complements this tool’s practical benefits for workshops and small-scale production. For tailored advice on the H.PREISSER scribing caliper and to secure supply from Metav Werkzeuge, contact our consultants at info@metav-werkzeuge.com or call +49 2822 7131930 Technical Data Article number: 4000851039NW Label: Anreißmessschieber 160mm m. FE Anschlag-L. 135mm H.PREISSER SKU: 4000851039NW Specifications Measurement range: 160 mm Resolution/readability: 0.05 mm Stop length: 135 mm Features Product type: Scribing caliper Packaging unit: 1 UID: 4000851039NW FAQ How accurate is this scribing caliper? The scribing caliper offers a 0.05 mm readability, providing precise layout marks across the 160 mm measuring span for reliable workshop use. Can the caliper produce identical offsets on multiple parts? Yes, the integrated 135 mm fixed stop ensures consistent offset marking, so repeated marks made with the scribing caliper remain uniform across batches. Which tasks are this tool best suited for? This instrument is intended for layout and marking in metalworking and general fabrication; the scribing caliper assists with transfer lines, jig set-up and preparatory marking before machining. Is the caliper suitable for everyday production environments? The robust design and simple maintenance needs make the scribing caliper well suited to regular workshop use, supporting steady production without complex servicing. What basic care does the scribing caliper require? Routine wiping to remove swarf, occasional light lubrication of the sliding surfaces and storage in a dry place will keep the scribing caliper functioning accurately over time. Manufacturer/Responsible: NORDWEST Handel AG, Robert-Schuman-Straße 17, 44263 Dortmund
165mm Rico Marker Carbide Scribe Automatic Retractable 12mm Resharpenable - TECWERK
Combine a pen-shaped aluminium body with an automatically retractable carbide tip and a 12 mm resharpenable cutting edge for accurate, repeatable workshop marking. Order the Rico-Marker directly via Metav Werkzeuge or consult our specialists for tailored advice. Rico-Marker HM – Automatic carbide scribe, 165 mm, TECWERK The Rico-Marker is a pen-shaped automatic carbide scribe designed for precise marking and durable workshop use Pen-shaped aluminium housing Retractable carbide tip, resharpenable 12 mm Knurled grip for secure handling Integrated pocket clip, robust construction Precise marks from a hardened carbide tip The central benefit of this pen-style marker is its carbide tip, which delivers consistent, precise marks on a wide range of surfaces. The automatic push mechanism ensures the tip is only exposed when pressure is applied, reducing accidental damage and guaranteeing reproducible results. With a 12 mm resharpenable allowance, the marking edge can be restored on-site, extending tool life and lowering total operating costs. For operations that require frequent layout work, the combination of a stable point and repeatable actuation reduces rework and speeds up set-up times. Robust, ergonomic design for everyday use A lightweight aluminium housing gives the tool both durability and a comfortable balance for extended handling, while the knurled grip provides slip-resistant control in oily or gloved conditions. The pen-shaped form factor and integrated pocket clip support portability and immediate access at the bench or on the machine. These design choices deliver practical benefits: less hand fatigue during repetitive marking and faster transitions between tasks, which together improve workflow efficiency in production and maintenance environments. Low-maintenance operation and longevity The automatic mechanism is engineered for simple, reliable action without complex maintenance. The carbide material resists wear far better than steel tips, and the ability to resharpen up to 12 mm of the tip reduces the need for replacements. This translates to fewer tool changes and reduced downtime. Where precision matters, the fixed geometry of the tip produces clear reference lines that remain visible throughout subsequent machining or finishing processes, reducing measurement uncertainty and assembly errors. Practical applications and material suitability This scribe is suited to a variety of workshop marking tasks, including layout on steel, aluminium, cast iron and other common substrates found in metalworking and fabrication. The automatic action and rigid tip make it appropriate for quick centre-punch alternatives or for producing fine scribe lines prior to machining. For specialised materials or unusual surface finishes, consult the product details to confirm compatibility and tip condition; the tool’s robust construction makes it a reliable choice for everyday industrial marking duties. For precision marking with a durable carbide tip, choose the TECWERK Rico-Marker and contact Metav Werkzeuge for expert guidance and supply — eMail: info@metav-werkzeuge.com or phone +49 2822 7131930 Technical data Article number: 4000858988NW SKU / UID: 4000858988NW Product type: Rico-Marker / Reißnadel Manufacturer: TECWERK Label: Reißnadel Rico-Marker HM L.165mm RICO-MARKER Packaging unit: 1 Data Length: 165 mm Resharpenable tip allowance: 12 mm Packaging unit: 1 Special features Pen-shaped aluminium housing Automatically retractable carbide tip Material: carbide (hard metal) Knurled grip for improved handling Integrated pocket clip Stable construction for workshop use FAQ How durable is the carbide tip on the Rico-Marker? The Rico-Marker uses a carbide (hard metal) tip designed for high wear resistance; the tip is resharpenable up to 12 mm to extend service life. Can the Rico-Marker be used on stainless steel and cast iron? Yes, the automatic carbide tip and robust construction make the tool suitable for marking materials such as stainless steel and cast iron under normal workshop conditions. Is the tip replaceable or does it only get resharpened? The design allows the tip to be resharpened for up to 12 mm of material removal; consult TECWERK guidance for replacement options if required. Manufacturer / Responsible: NORDWEST Handel AG, Robert-Schuman-Straße 17, 44263 Dortmund
175mm Scriber Steel Pointed Tip, Single Point - Metav IndustryLine
Take advantage of the combination of precise single‑point marking, robust metal construction, and an ergonomic 175 mm length for repeatable layout work in the workshop; order the tool directly via Metav Werkzeuge or consult our product advisers for application guidance. Scribing Needle M214.031 — 175 mm single‑point marking needle | Metav IndustryLine The Scribing Needle M214.031 is a hand marking tool designed for precise layout and scribing tasks in workshop and production environments, offering a long, easy‑to‑handle shaft for controlled lines and points Single‑point hardened tip 175 mm overall length Robust metal construction Lightweight 20 g Precise layout marks with minimal effort A long, rigid shaft and a single‑point tip deliver consistently sharp lines for layout work. The shaft length of 175 mm gives a comfortable reach without compromising control, so marks remain repeatable even on awkward or recessed surfaces. The simple geometry of the point converts a modest hand force into a fine, accurate score, which is particularly valuable when transferring centre lines or reference points prior to machining or assembly. The combination of length and balance reduces wobble and enables controlled marking along edges and across flat faces. Built for everyday workshop reliability Constructed from robust metal, the tool withstands the knocks of daily use while remaining straightforward to maintain. The durable material and hardened tip keep the point geometry intact for longer, reducing the need for frequent dressing or replacement. The design focuses on functional longevity rather than added complexity: a single‑purpose marking instrument that performs reliably as part of a small tool set or larger layout station. The lightweight nature (approx. 20 g) means the needle sits comfortably in a pocket or tool roll without adding bulk. Ergonomic handling for faster workflow The slender profile and balanced shaft promote precise hand positioning and controlled scribing strokes, speeding up repetitive layout tasks. Because the tool is easy to grip and manoeuvre, marking operations become less fatiguing over a production shift, which supports higher throughput without compromising accuracy. The straightforward form factor also simplifies storage and issue control in busy workshops, ensuring the needle is available and ready when needed. Choose the Metav IndustryLine Scribing Needle for dependable, workshop‑grade marking — contact Metav Werkzeuge in Emmerich for purchasing details or technical advice at info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: M214.031 GTIN: 4054469106229 Tariff number: 90172039 EClass: 21049238 Facts Length: 175 mm Weight: 0.02 kg Special features Material: Metal Tip: Single point Category: Marking and layout tools (Anreisszeuge) FAQ What materials is the needle suitable for marking? The scribing needle is made of metal with a hardened single‑point tip and is intended for conventional layout marking on workpieces and surfaces encountered in workshop use How long is the tool and how heavy is it? The tool measures 175 mm in overall length and has a mass of approximately 0.02 kg (20 g); it is designed for easy handling and reach Is the tip replaceable or serviceable? The instrument is a simple, durable marking tool with a hardened tip; routine maintenance consists of keeping the tip clean and, if necessary, reshaping the point with appropriate tooling Which brand and SKU should be quoted when ordering? Please quote Metav IndustryLine Scribing Needle, SKU M214.031, for ordering and identification in procurement Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
180mm Scratch Awl Hardened Blued Finish, One-Piece Construction - TECWERK
Take advantage of a robust, one-piece scribing tool that combines durability and clear layout performance; the fully hardened, blued finish ensures long service life and low maintenance in daily workshop use. Order directly via Metav Werkzeuge or consult our specialists for application advice. TECWERK Scriber 180 mm — fully hardened, blued workshop scriber A TECWERK Scriber 180 mm is designed for precise layout and marking in metalworking and general workshop applications. One-piece hardened construction Blued corrosion-resistant finish 180 mm length for stable marking Workshop-grade precision scribing Long-lasting construction for repeatable layout work The core advantage of this scribing tool is its one-piece construction, which eliminates joints that can loosen or fail under repeated use. The component is fully hardened, giving it resistance to bending and wear during light to medium scribing tasks; this translates into fewer tool changes and more consistent precision marking across production runs. For fabricators and maintenance technicians, the robust design reduces downtime and supports steady workflow on the shop floor. Clean, readable scribe lines with a corrosion-resistant finish A blued finish provides a thin, dark layer that reduces surface reflections and helps the scribe line remain visible on bright metal faces. The treated surface also offers basic corrosion resistance, extending the time between maintenance cycles. The 180 mm length gives a good balance between reach and control, permitting stable contact with the workpiece while limiting flex. These attributes make the instrument suitable for layout on ferrous parts and for everyday marking tasks in a busy workshop environment. Simple handling and low-maintenance operation The straight, balanced geometry enables steady hand control and predictable line placement, which is essential when transferring measurements or preparing parts for machining. The hardened tip holds an edge for longer than untreated alternatives; when resharpening is necessary, light honing restores the tip quickly. With only essential, proven features, the tool offers a cost-effective way to maintain layout accuracy without complex consumables or special handling procedures. Practical fit for supply chains and workshop kits The compact, dependable design suits both single-station tool kits and central stores supplying multiple workbenches. Selected as part of a standard layout kit, the instrument supports consistent part preparation and quality control. For customers seeking supply assurance and technical guidance, Metav Werkzeuge offers access to a broad product range and a reliable logistics base from Emmerich, backed by decades of distribution experience and a large customer base in Europe. Choose the TECWERK scriber for dependable layout performance and contact Metav Werkzeuge for supply and expert advice via info@metav-werkzeuge.com or +49 2822 7131930 Technical Data Article number: 2000858991NW SKU: 2000858991NW Label: Reißnadel brün.L.180mm TECWERK Product type: Scriber Manufacturer: TECWERK Packaging unit: 1 UID: 2000858991NW Dimensions & core data Length: 180 mm Packaging unit: 1 Materials & special features One-piece construction Fully hardened Blued finish (brüniert) aus einem Stück · ganz gehärtet · brüniert FAQ What materials is the scriber suitable for marking? The TECWERK Scriber 180 mm is intended for layout and marking on typical workshop metals; its hardened point performs well on ferrous surfaces and common fabrication materials. How should the tip be maintained to keep precise scribe lines? Light honing restores the point; for the TECWERK 180 mm scriber, brief reshaping on a fine stone returns the geometry needed for crisp lines. Does the blued finish prevent rust completely? The blued finish on the TECWERK scriber provides surface corrosion resistance and reduces glare, but it is not a substitute for storage in dry conditions. Is the construction suitable for heavy workshop use? The one-piece, fully hardened design of this scriber supports everyday workshop applications and offers improved resistance to bending and wear compared with non-hardened tools. Manufacturer / Responsible: NORDWEST Handel AG, Robert-Schuman-Straße 17, 44263 Dortmund
2 mm Replacement Scriber Tip 33 mm Carbide - Metav IndustryLine
Take advantage of the carbide tip and compact 33 mm length to restore precise scribing performance with minimal downtime; the light 1 g replacement combines durability and easy fitment for efficient workshop replenishment — order directly from Metav Werkzeuge or contact our consultants for compatibility guidance. Replacement scribing needle, Ø 2 mm – Carbide tip, 33 mm length (Metav IndustryLine) Replacement scribing needle, Ø 2 mm – Carbide tip, 33 mm length is a precision accessory for scribing calipers, designed to restore crisp marking capability on component surfaces prior to machining. Carbide scribing tip Ø 2 mm 33 mm hardened precision length Suitable for standard scribing calipers Lightweight 1 g replacement part Engineered for consistent, high-contrast marks The replacement scribing needle is built around a carbide tip with a nominal Ø 2 mm diameter and a 33 mm overall length, offering a predictable contact geometry for repeatable scribing. Carbide provides a high hardness-to-toughness ratio, which means the tip keeps a clean edge under regular workshop use and wears significantly slower than simple tool steels. This reliable tip material translates into fewer interruptions for tool changes and a consistent line width that improves downstream machining and inspection readability. Fits routine maintenance cycles and reduces downtime As a direct spare part for scribing calipers, the needle is a fast-change solution that restores measuring and marking capability without the need for tool recalibration in most cases. The component’s negligible mass (approximately 1 g) preserves the balance of the parent instrument and avoids altering handling characteristics during one-handed operation. Supplied as a compact replacement item, it supports straightforward stock management in small to medium workshops and production cells, helping to keep the production flow continuous and predictable. Robustness for workshop environments and broad marking tasks The carbide construction ensures resistance to abrasive wear, making the needle suitable for repeated marking of ferrous and non-ferrous component surfaces encountered in preparatory layout work. While intended for scribing and layout prior to machining, the durable tip tolerates normal workshop contaminants and handling better than softer alternatives. Where longevity matters, the hardened construction reduces the frequency of replacements and supports a cost-conscious maintenance strategy aligned with Metav’s emphasis on accessible precision. For rapid replenishment and assured precision, request the Metav IndustryLine replacement needle M201.155 from Metav Werkzeuge — contact via info@metav-werkzeuge.com or +49 2822 7131930 to confirm fitment and delivery options Technical Data Article number: M201.155 GTIN: 4061905053597 Weight: 0.001 kg (1 g) Material: Carbide Item label: Replacement scribing needle, Ø 2 mm, L 33 mm Facts Diameter: 2 mm Length: 33 mm Mass: 0.001 kg Special features Carbide tip for improved wear resistance Designed as a direct replacement accessory Compact, lightweight design FAQ What is the M201.155 intended for? The M201.155 replacement scribing needle is intended as a spare scribing tip for scribing calipers, restoring precise layout marking capability on component surfaces prior to machining. Which materials can be marked with this carbide needle? Because the needle is made of carbide, the M201.155 is suited to scribing most common workshop component surfaces used for layout work; it is optimised for durable, repeatable marks rather than cutting or heavy abrasion. How long does the replacement needle typically last? Service life depends on use and workpiece abrasiveness; the carbide construction of the M201.155 provides significantly higher wear resistance than softer tips, reducing replacement frequency under normal layout and marking conditions. Is installation of the replacement needle difficult? Installation is designed to be straightforward: remove the worn tip from the scribing caliper and fit the M201.155 in its place, ensuring secure seating. The low mass of the needle preserves handling characteristics of the caliper. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
2000mm Steel Scale Bending Stainless Spring Steel Laser-Etched 1/2mm Graduation - TECWERK
Its laser‑etched mm/1/2 mm graduations combined with a flexible stainless spring steel strip ensure repeatable, workshop-grade measurements over the full 2000 mm length; practical rigidity is delivered by the 30 x 1 mm cross-section while the rule remains subject to official verification. Order the measuring rule directly via Metav Werkzeuge or request further advice from their consultants. Flexible Stainless Steel Measuring Rule L 2000 mm (TECWERK) — laser-etched mm / 1/2 mm scale, 30 x 1 mm Flexible Stainless Steel Measuring Rule L 2000 mm (TECWERK) is a laser‑etched, bendable measuring scale for industrial and workshop dimensional checks, suitable where corrosion resistance and compact storage are required. Laser-etched mm / 1/2 mm graduations Flexible stainless spring steel strip Cross-section 30 x 1 mm for stability 2000 mm usable measuring length Accurate graduations for reliable dimensional control The laser-etched graduation provides a clear and wear-resistant scale that supports consistent readings throughout the service life. With mm/1/2 mm spacing, the rule enables fine interpolation for typical workshop tasks and process checks; the marked divisions are produced by removing material rather than ink application, which reduces fading and keeps resolution intact under repeated handling. This permanence supports precision documentation and reduces measuring errors during layout, inspection or assembly operations. Robust, bendable construction that saves space Manufactured from stainless spring steel, the strip combines flexibility with sufficient stiffness to lie flat during measurement. The 30 x 1 mm cross-section offers a balance between bending radius and handling stability, so long runs up to 2000 mm can be measured with less sag than thinner alternatives. Corrosion resistance of the stainless material minimises maintenance and preserves surface quality in humid or varying workshop environments, prolonging the tool’s usable life and reducing replacement cycles. Inspection status and traceability for production use The item is marked as inspection required, which indicates suitability for workplaces with documented quality control or calibration regimes. Recording the rule’s verification status and traceability supports internal audits and helps maintain process compliance where documented measurements are mandatory. The combination of a durable, readable scale and a verifiable status simplifies integration into inspection intervals and quality documentation routines. Everyday practicality: handling, storage and application The 2‑metre length is ideal for checking long components, setting out jobs and transferring dimensions directly from drawings to workpieces. Thanks to its flexible design the rule can be coiled for compact storage without losing its measuring integrity, and the laser-etched markings remain legible when the strip is wrapped or partially tensioned. For workshops that alternate between bench work and on-site checks, this tool offers a pragmatic compromise of length, durability and portability. The product name appears as the flexible stainless steel measuring rule for identification and ordering. For reliable, workshop-ready measurement solutions from TECWERK, request availability or a technical consultation via Metav Werkzeuge — contact info@metav-werkzeuge.com or call +49 2822 7131930 for immediate assistance and ordering details. Technical data Article number: 4000858770NW Description: Flexible stainless steel measuring rule, laser-etched scale Manufacturer: TECWERK Dimensions and measurable data Length: 2000 mm Cross-section: 30 x 1 mm Graduation: mm / 1/2 mm Packaging unit: 1 Material and special features Material: stainless spring steel strip Scale: laser-etched Design: flexible / bendable Inspection required: yes FAQ What level of detail do the graduations provide? The laser‑etched markings offer mm/1/2 mm resolution; the Flexible Stainless Steel Measuring Rule L 2000 mm (TECWERK, SKU 4000858770NW) is suitable for fine layout and comparative checks where half‑millimetre divisions are useful. Is the rule resistant to workshop corrosion? Yes, the measuring strip is produced from stainless spring steel, so the rule resists rust in standard workshop conditions and keeps the laser‑etched scale legible over time. Can the rule be stored compactly without losing accuracy? The flexible construction allows coiling and compact storage; repeated correct handling preserves the flatness needed for accurate measurements across the 2000 mm span. What does 'inspection required' mean for daily use? 'Inspection required' indicates the rule should be included in regular verification or calibration cycles for traceable measurements; the product’s durable scale and defined status simplify record keeping. Is the cross-section suitable for long‑length measurements? The 30 x 1 mm cross-section provides improved straightness under light tension compared with thinner strips, reducing sag over the 2000 mm measuring length for more reliable results. Manufacturer / Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund
2000mm Steel Scale Flexible Stainless Steel Division A mm/mm, Laser Marked - TECWERK
Take advantage of the laser-etched scale, flexible stainless spring steel and the long 2,000 mm measuring range to speed up layout and inspection tasks. The robust, bendable profile reduces handling time and stays readable over a long service life. Order supply or request application advice via Metav Werkzeuge if further clarification is required. Steel Measuring Rule 2,000 mm (flexible stainless spring steel) — H.PREISSER Steel Measuring Rule 2,000 mm for clear metric measurements with mm/mm division, designed as a flexible stainless spring steel strip for workshop and inspection use. Laser-etched scale for permanent clarity Flexible stainless spring steel construction Length: 2,000 mm for long-range measurement Division A = mm/mm, millimetre graduations Long-range precision for layout and inspection The 2,000 mm measuring strip offers an extended measuring range while remaining compact when rolled or stored. Manufactured from stainless spring steel, the format combines corrosion resistance with a spring effect that allows gentle bending around profiles without permanent deformation. This construction reduces the risk of measurement error from surface corrosion and maintains reliable edge alignment during repeated use, which supports consistent precision in production and inspection tasks. Permanent graduations to reduce read‑back errors A laser-etched scale provides scratch- and wear-resistant graduations so readings remain legible over many service cycles. The Division A = mm/mm marking denotes clear millimetre graduations suitable for metric layout, marking and comparative measuring where millimetre resolution is required. The contrast and permanence of the etching minimise rework due to illegible markings and speed up routine checking operations in busy workshops. Slim profile and practical dimensions for everyday use With a 30 x 1 mm cross-section, the blade offers a slim, stable profile that is easy to handle and lies flat on workpieces. The narrow thickness keeps the rule flexible yet robust, allowing it to be used for both straight measurement and temporary conformation to gentle curves. Marked as inspection required, the item is intended to be subject to verification routines appropriate for workplace quality assurance; this ensures traceable results when the rule is used for control or calibration tasks. Ready for workshop conditions and diverse applications The combination of a flexible strip and stainless spring steel makes this measuring rule well suited to metalworking layouts, carpentry set‑ups and general workshop measurement where durability and clarity are priorities. The design reduces the need for frequent replacements and supports efficient workflow during marking, cutting and quality checks. For special applications or integration into inspection processes, additional verification and calibration services can be arranged. Contact Metav Werkzeuge for supply and verification options for this H.PREISSER steel measuring rule — Metav Werkzeuge can advise on inspection intervals and delivery from Emmerich, call +49 2822 7131930 or email info@metav-werkzeuge.com Technical data Item number: 4000858767NW Product type: Steel measuring rule Label: Stahlmaßstab L.2000mm rostfr. Stahl biegsam Teilung A=mm/mm H.PREISSER Facts Length: 2,000 mm Cross-section: 30 x 1 mm Packaging unit: 1 Inspection required: yes Special features Laser-etched scale Flexible (bendable) stainless spring steel Division A = mm/mm Slim profile for flat contact FAQ What is the measuring resolution of the rule? The rule features a Division A = mm/mm marking, providing millimetre graduations suitable for standard metric layout and measurement. Can the rule be bent for curved surfaces? Yes, the flexible stainless spring steel construction allows temporary bending to follow gentle curves while maintaining accuracy and returning to a flat profile. Is the scale resistant to wear in workshop conditions? The laser-etched graduations are designed for permanence and high abrasion resistance, keeping markings legible under repeated use. Does the item require verification for inspection use? The product is marked as inspection required; periodic verification or calibration is recommended when used for official quality checks. What are the physical dimensions of the measuring strip? The measuring strip is 2,000 mm long with a cross-section of 30 x 1 mm, offering a slim yet stable profile. Manufacturer / Responsible: NORDWEST Handel AG, Robert-Schuman-Straße 17, 44263 Dortmund
200mm Digital Fräsereinstelllehre, 0,01mm - Metav IndustryLine
Das 1989 gegründete Vertriebsunternehmen von Messwerkzeugen steht mit seiner Eigenmarke Metav IndustryLine für Premium-Messwerkzeuge zu einem überzeugenden Preis. Informationen zur technischen Ausstattung für digitale Fräsereinstelllehre von Metav IndustryLine: Marke: Metav IndustryLine Bezeichnung: Fräsereinstelllehre Bestellnummer: M240.196 Zahlen: Messbereich: 0 bis 200mm Gewicht: 0,4kg Schnabellänge: 80mm Ablesung: 0,01mm Ablesung in Inch/Zoll: 0,0005 Genauigkeit: 0,05mm Anschlag: 100x10x10mm Besonderheiten Ausführung: digital Lieferung im Kasten Anzeige: mit EIN/AUS-, mm/inch- und NULL-Taste Geeignet für Messschieber: die Einstellung von z.B Sägeblätter, Fräser-Tiefen oder zur Höhenmessung Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; www.metav-shop.de; info@metav-werkzeuge.com
200mm Digital Scriber Caliper T-Form 100mm Stop, 150mm Scribing Rail, 0.01mm Resolution, Stainless Steel Case - Metav IndustryLine
Combine the 200 mm measuring range, a hardened stainless steel scribing edge and a clear digital readout for reliable layout and repeatable marking; order the M240.156 directly via Metav Werkzeuge or consult our advisors for tailored workshop recommendations. Digital marking caliper M240.156 (200 mm, T‑form, 150 mm scribing rail) — Metav IndustryLine A digital marking caliper M240.156 engineered for precise scribing and repetitive layout tasks in metalworking and toolrooms, pairing a 200 mm measuring range with a stable T‑form frame and an integrated 150 mm scribing rail. 200 mm measuring range with T‑form stability Hardened stainless steel body with bevelled scribe Fine adjustment wheel for controlled marking Digital display with zero/unit/hold functions Repeatable layout accuracy for everyday workshop use The caliper is classified in the Standard range (measuring range up to 300 mm), which offers the best balance between reach and rigidity for general machine‑shop and metalworking tasks. With a display resolution of 0.01 mm, the instrument provides clear, workshop‑grade readings that simplify quality control and reduce rework. The built‑in fine adjustment wheel lets operators position the scribe with steady, controlled movement, so marks and reference lines are placed consistently. This focus on measurable, repeatable outcomes makes the tool a practical choice where speed and traceable accuracy matter. Robust materials that withstand daily handling Constructed from hardened stainless steel with a bevelled scribing edge and a metal housing, the caliper resists wear from frequent contact with abrasive shop surfaces and cutting fluids. The T‑form frame increases torsional stiffness, improving measurement stability during layout operations and preventing unwanted twist when working on small fixtures. At around 0.5 kg, the instrument balances solidity and manoeuvrability—heavy enough to feel stable, yet light enough for one‑handed positioning at a bench. These material choices extend service life and reduce the total cost of ownership through fewer replacements. Designed for controlled marking and efficient workflows The integrated 150 mm scribing rail and a dedicated 100 mm stop enable fast, repeatable marking across multiple workpieces without relying on improvised jigs. The clear digital display (with ON/OFF, ZERO, UNIT and HOLD buttons) supports quick zeroing and unit changes on the fly, while the fine adjustment mechanism permits sub‑millimetre alignment before scribing. Together, these features transform a manual layout step into a controlled, semi‑mechanised process that improves throughput and reduces operator variability—an important rational benefit for production environments. Data handling and power supply suited to shop integration Equipped with a data output labelled RB 5, the caliper allows connection to compatible readout or data‑collection systems for logging measurements directly into inspection routines or spreadsheets. The measuring system is powered by 3 V, ensuring long battery life for typical workshop use and straightforward battery replacement when required. These integration options support digital traceability and make the tool a practical component of modern quality workflows without requiring complex setup. Discuss the suitability of the Metav IndustryLine M240.156 for your production needs with Metav Werkzeuge in Emmerich — technical advice and reliable supply are available by email or phone Technical data Article number: M240.156 GTIN: 4054469178196 ECLASS: 21170344 Tariff number: 90173000 Facts Measuring range: 0–200 mm Resolution: 0.01 mm (0.0005 in) Weight: 0.5 kg Scribing rail length (bridge): 150 mm Stop length: 100 mm Power supply: 3 V Data output: RB 5 Special features T‑form frame for increased stiffness Hardened stainless steel with bevelled scribing edge Metal housing Fine adjustment wheel for controlled positioning Digital display with ON/OFF, ZERO, UNIT and HOLD functions Suitable for layout and marking in machine shops and toolrooms FAQ What measuring range does the caliper cover? The digital marking caliper M240.156 covers 0–200 mm, placing it in the Standard class commonly used in machine and metal workshops. Is the scribing edge durable enough for workshop use? Yes, the instrument features a hardened stainless steel body with a bevelled scribing edge designed for repeated contact with workpiece surfaces. Can measurements be recorded electronically from the caliper? The M240.156 includes a data output marked RB 5 for connection to compatible readout systems and data capture workflows. How is fine positioning achieved during marking? A fine adjustment wheel provides controlled, incremental movement for precise alignment before scribing, improving repeatability. What display and control functions are available on the caliper? The digital readout offers ON/OFF, ZERO, UNIT and HOLD buttons for quick zeroing, unit changes and value retention during layout operations. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
200mm Digital Scriber Caliper With 50×40mm Scriber Plate And Adjustable Scribing Pin, Stainless Steel, Data Output RB 5 - Metav IndustryLine
For consistent workshop marking and dependable measurements, benefit from the combination of a 200 mm measuring range, 0.01 mm resolution and an adjustable scribing needle for repeatable layout work; order the Digital scribing caliper M240.152 directly via Metav Werkzeuge or ask our consultants if needed. Digital scribing caliper M240.152 — 200 mm, adjustable scriber, Metav IndustryLine Digital scribing caliper M240.152 is a purpose-built marking and measuring tool for metalworking and general workshop use, combining a compact 200 mm measuring range with a robust scribing plate and moveable scriber for precise layout and repeatable scores. 200 mm digital marking caliper 0.01 mm resolution with four-button display Adjustable scribing needle for precise layout Stainless steel body with solid measuring rod Precise marking and dependable workshop reach The Digital scribing caliper M240.152 places a 200 mm measuring range in the proven Standard class for workshop hand tools, offering the best compromise between reach and stiffness for everyday machine‑shop tasks. The 0.01 mm display resolution provides clear numerical feedback for reliable measurements, while the included 50 x 40 mm scribing plate gives a stable reference surface for scoring. Thanks to the massive measuring rod, the instrument resists torsion during lateral marking, improving repeatability when transferring dimensions to components. Clear digital feedback and secure data handling A tidy, user‑oriented digital display with ON/OFF, ZERO, UNIT and HOLD keys simplifies routine checks and reduces setting errors at the bench; the inch readout is available at 0.0005 in for mixed‑unit workflows. For process documentation the caliper offers data output RB 5, enabling downstream capture of measured values where required. The light‑weight construction at 0.6 kg keeps handling straightforward without compromising the rigid feel needed for accurate layout. Robust design built for everyday use Constructed from stainless steel with a metal housing, the tool tolerates standard workshop strains and keeps wear to a minimum. The adjustable scribing needle (5 x 60 mm) slides for fine positioning and fixes securely for repeat marks, while the solid 15 x 6 mm measuring rod is supplied with the instrument to ensure dimensional stability from the first measurement. Overall, the caliper is engineered for routine marking, quick checks and integration into a busy production environment. For hands‑on advice or to place an order for the Metav IndustryLine digital scribing caliper, contact Metav Werkzeuge directly at info@metav-werkzeuge.com or call +49 2822 7131930 — our consultants will advise on suitability and delivery options. Technical data SKU: M240.152 Manufacturer: Metav IndustryLine Category: Marking tools (Anreisszeuge) GTIN: 4054469178356 Facts Measuring range: 0–200 mm Resolution: 0.01 mm / 0.0005 in Weight: 0.6 kg Plate dimensions: 50 x 40 mm Scriber needle: 5 x 60 mm Measuring rod: 15 x 6 mm Power supply: 3 V Special features Stainless steel with metal housing Adjustable scribing needle Digital display with ON/OFF, ZERO, UNIT, HOLD Solid measuring rod included Data output: RB 5 FAQ What measuring range does this marking caliper cover? The instrument covers a measuring range of 0–200 mm, classifying it as a Standard workshop caliper suitable for general machine‑shop and metalworking tasks. How accurate is the readout of the device? The digital readout delivers a resolution of 0.01 mm (0.0005 in), providing precise numerical feedback for layout and verification work. Is the scribing needle adjustable and replaceable? Yes — the scribing needle on the Digital scribing caliper M240.152 is adjustable for exact positioning and is secured for repeat markings. Which materials is the caliper suited to mark and measure? With a stainless steel body and robust scribing plate, the caliper is ideal for marking and measuring common workshop materials such as steel and aluminium during layout operations. Does the caliper provide a data interface for recording measurements? The Digital scribing caliper M240.152 includes a data output designated RB 5 for integration with data collection systems where needed. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
200mm Hairline Gauge Hardened Stainless Steel Lapped Edges Matt Finish Hand Heat Shield - TECWERK
Combine hardened stainless steel with lapped measuring edges to secure reliable reference measurements; the 200 mm DIN 874 straight edge offers low-reflection handling and thermal protection for consistent results. Order the straight edge directly via Metav Werkzeuge or consult the product specialists for specification support. Hairline straight edge DIN 874/00 — 200 mm precision straight edge by TECWERK Hairline straight edge DIN 874/00 — 200 mm precision straight edge by TECWERK is a compact metrology tool for establishing straight reference lines and checking flatness in workshops and inspection bays Stainless steel, hardened and ground Lapped measuring edges for precision Hand-heat protection reduces thermal error Matt, non-reflective surface finish Compliant with DIN 874/00, 200 mm length Proven reference flatness for workshop inspection A compact precision straight edge that fulfils laboratory-grade reference tasks while remaining workshop-friendly. The combination of hardened and ground stainless steel and lapped measuring edges provides a stable reference line for visual and tactile checks. In practice, the straight edge serves as a quick verification tool for planing, aligning and surface checks; the DIN 874/00 designation defines the geometric features so comparisons across tools and procedures remain consistent. Errors introduced by surface irregularities are minimised by the fine lapping of the measuring faces, which improves repeatability in everyday production control. Reduced measuring error through thermal and optical control Thermal influence is a frequent source of measurement drift; the integrated hand-heat protection lowers direct heat transfer from the operator, so the metal body remains closer to ambient temperature during use. The matt, non-reflective finish reduces glare under workshop lighting, aiding visual alignment and reducing eye strain during inspection. Together, these characteristics make the straight edge a reliable short-range comparator for edges, steps and joint checks where even small thermal or optical biases would otherwise compromise judgement. Practical benefits for industrial and craft environments The compact 200 mm length and a slender 28 x 6 mm cross-section make the tool easy to manoeuvre in confined areas while still providing a usable reference span. The robust stainless construction ensures corrosion resistance and long service life under normal workshop conditions. As the device requiresinspection required**, it fits into documented quality-control routines: periodic verification keeps the reference within tolerance and supports audit trails. For technicians familiar with metrology, the straight edge complements calipers and surface plates as a rapid-check instrument. Documentation, maintenance and sourcing confidence Maintenance is straightforward: keep the measuring faces clean and store the straight edge away from abrasive contact to preserve the lapped edges. When certification or re-verification is necessary, the product’s status as requiringinspection required** status indicates a route for scheduled checks to maintain traceability. Metav’s distribution from Emmerich offers consolidated access to measuring instruments and workshop supplies, backed by decades of market presence and a wide product range, which helps reduce supplier overhead and ensures consistent supply for routine calibration cycles. Contact Metav Werkzeuge to discuss TECWERK specification details or to arrange immediate dispatch from Emmerich for fast integration into the quality workflow Technical data Article number: 2000858394NW Label: Haarlineal DIN 874/00 L.200mm Spezialstahl Q.28x6mm TECWERK Product type: Hairline straight edge Manufacturer: TECWERK SKU: 2000858394NW Facts Length: 200 mm Cross-section: 28 x 6 mm Packaging unit: 1 Inspection required: yes Special features Material: stainless steel Hardened and ground Measuring edges lapped Hand-heat protection Matt, non-reflective finish FAQ What is the intended use of this straight edge? The TECWERK hairline straight edge is intended as a short-span reference tool for checking straightness, alignment and small-surface flatness in workshop and inspection environments. How does the hand-heat protection help during measurement? Hand-heat protection on the straight edge reduces thermal transfer from the operator, limiting distortion and preserving measurement consistency for tasks requiring stable reference lines. Is the straight edge suitable for calibration routines? Yes. The product is marked as requiring inspection required; it can be integrated into regular verification cycles to maintain traceability and compliance with internal quality procedures. What does the matt, non-reflective finish provide? A matt finish minimises glare under workshop lighting, improving visibility of contact lines and reducing visual fatigue during frequent checks. Can the straight edge be used on delicate surfaces? The lapped measuring edges deliver a fine contact surface; careful handling and correct storage are recommended to avoid wear that could affect accuracy. Manufacturer / Responsible: NORDWEST Handel AG, Robert-Schuman-Straße 17, 44263 Dortmund
200mm Scratch Gauge Flat Stainless Steel Hardened Scribing Edge With mm Scale - Metav IndustryLine
Take advantage of a stainless steel, flat-profile design with a hardened scribing edge and clear millimetre scale to speed up layout work and reduce rework; order the marking gauge directly via Metav Werkzeuge or consult our specialists for selection advice. M201.194 marking gauge — Flat INOX scribing rule, 200 mm, Metav IndustryLine M201.194 marking gauge is a flat stainless steel scribing rule with a hardened scribing edge and a matt-chromed millimetre scale, designed for precise layout and scribing tasks in metalworking and general workshop applications. Flat INOX body for low-profile scribing Hardened scribing edge for repeatable marks Millimetre scale, analogue precision Precision and material that reduce layout error The flat stainless construction combines a low-profile form with robust surface hardness to support repeatable layout operations. The matt-chromed millimetre scale provides a clear analogue reference while the hardened scribing edge resists wear, so marks remain consistent over many cycles. As a tool in the standard measuring range (max 100–300 mm), this 200 mm rule balances reach and stiffness — a pragmatic choice for everyday workshop layout that minimises alignment errors and reduces time spent on corrective work. Practical usability for workshop workflows Designed as an analogue marking instrument, the flat rule excels where firm, repeatable scribing is required on metal and other engineering materials. The low profile allows access close to edges and in shallow recesses, while the visible scale simplifies rapid transfer of measurements. In production and assembly contexts the tool supports efficient preparation of parts and fixtures by delivering a straightforward, durable method for transferring dimensions, avoiding the complexity of electronic systems when mechanical reliability is preferred. Built for durability and consistent performance Constructed from stainless steel with a matt-chromed scale and a heat-treated scribing edge, the flat rule is made to withstand workshop environments and regular use. The analogue design keeps maintenance simple and parts readily serviceable; the hardened edge reduces the need for frequent replacement, thereby lowering lifetime operating costs. As part of the Metav IndustryLine, this marking instrument reflects a focus on accessible precision for industrial and craft applications, bringing reliable layout accuracy to the bench or production line. Choose the Metav IndustryLine marking gauge for dependable scribing accuracy and contact Metav Werkzeuge for personalised advice or immediate dispatch from our Emmerich stock Technical Data SKU: M201.194 GTIN: 4054469101071 Tariff number: 90173000 ECLASS: 21170302 Label: Streichmaß 200mm, INOX flache Ausführung, Anreißkante gehärtet Facts Measuring range: 0–200 mm Scale: millimetre Analogue instrument: yes Special features Material: stainless steel (INOX) Scale finish: matt-chromed Scribing edge: hardened Execution: flat version Category: marking tool (Anreisszeuge) FAQ What materials can be scribed with this marking gauge? The M201.194 marking gauge is made of stainless steel with a hardened scribing edge and is suitable for scribing on typical workshop materials used in metalworking and general fabrication. Is the millimetre scale suitable for fine layout accuracy? Yes, the matt-chromed millimetre scale on this flat rule gives a clear analogue reference that supports precise layout work within the 0–200 mm measuring range. How does the hardened scribing edge benefit everyday use? A hardened scribing edge on the M201.194 reduces wear from repeated marking, ensuring consistent mark quality and longer service life compared with non-hardened edges. Is this tool appropriate for both bench and on‑machine layout tasks? The flat profile and robust construction make the instrument well suited to bench work and many on‑machine layout situations where a low-profile scribing reference is needed. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
200mm Scratch Gauge Hardened Scribing Edge With mm Scale - Metav IndustryLine
The combination of a hardened scribing edge, a clear mm scale and robust steel construction ensures precise layout and durable performance; order the marking gauge directly via Metav Werkzeuge or consult the team for application advice. Marking gauge M201.191 — 200 mm hardened scribing edge (Metav IndustryLine) The Marking gauge M201.191 is an analogue workshop layout tool designed for accurate scribing and transfer marking across a 200 mm range, ideal for general metal and woodworking tasks. Hardened scribing edge for lasting precision Matt chrome scale with mm graduation 200 mm measuring range for workshop tasks Robust mild steel construction Precision layout that reduces rework As a dedicated layout instrument, this gauge delivers repeatable line placement thanks to its hardened scribing edge, which resists wear and preserves edge geometry over prolonged use. The clear mm graduation on a matt chrome scale supports exact positioning, making the tool suitable for both coarse and fine layout tasks. By reducing uncertainty at the marking stage, the tool contributes directly to fewer correction cycles and faster parts throughput. Built for workshop endurance and simple handling Constructed from mild steel with a matt-chrome finished scale and a heat-treated scribing contact, the device is balanced for everyday use while offering resilience under shop conditions. The solid build provides tactile feedback during layout without excessive flex, and the analogue design keeps operation straightforward: set, lock and scribe. This simplicity supports efficient workflows in production and repair environments where robust, low-maintenance tools are preferred. Practical range and application focus With a measuring span of 200 mm, the gauge sits in the Standard category of layout tools, offering the optimal compromise between reach and rigidity for general machine- and metalworking applications. The configuration is well suited for marking edges, aligning drill positions and transferring reference lines on components and stock. The instrument’s specification favours repeatable manual processes rather than automated measurement, making it a pragmatic choice for workshops seeking reliable mechanical layout aids. Contact Metav Werkzeuge today to request a specification sheet or to reserve the Metav IndustryLine marking gauge M201.191 for your workshop: info@metav-werkzeuge.com / +49 2822 7131930 Technical Data Article number: M201.191 GTIN: 4054469101040 ECLASS: 21170302 Customs tariff number: 90173000 Facts Measuring range: 0–200 mm Instrument type: analogue marking gauge Scale: mm graduation Category: Anreisszeuge (layout tools) Special features Material: mild steel Scale finish: matt chrome-plated Scribing edge: hardened Brand: Metav IndustryLine FAQ What materials can be marked with this gauge? The marking gauge M201.191 is made from mild steel with a hardened scribing edge and is suitable for marking on metals and common workshop materials where a durable scribe is required. How accurate is the mm scale on the instrument? The mm graduation on the Metav IndustryLine marking gauge provides clear, analogue reference lines for layout work; it is intended for precise manual marking rather than dimensional inspection to micrometric tolerances. Is the scribing edge replaceable or serviceable? The hardened scribing edge is designed for longevity; normal maintenance consists of keeping the edge free from burrs and corrosion. For extended service life, the edge may be professionally reconditioned if required. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
200mm Scriber Caliper With Replaceable Carbide Scriber And Roller, 0.05mm Resolution, Stainless Steel, Supplied In Case - Metav IndustryLine
Take advantage of the combination of durable materials, a replaceable carbide scribing tip and precise analogue reading for consistent layout work in production environments; order the scribing caliper directly via Metav Werkzeuge or ask the consultants for specification advice. Scribing Caliper with Roller M201.151 – 200 mm, 0.05 mm (Metav IndustryLine) The Scribing Caliper with Roller M201.151 is an analogue stainless-steel marking and measuring instrument designed for precise layout and scribing tasks in machine shops and metalworking production. Replaceable carbide scribing tip 200 mm measuring range, standard workshop length 0.05 mm scale resolution, analogue vernier Stainless steel, matt chrome finish with case Consistent layout and repeatable scribing The scribing caliper is engineered to turn layout work into a reproducible process. The replaceable carbide tip provides a hard-wearing contact point that retains a sharp mark over many cycles, while the integrated roller ensures steady contact against profiles when following edges or marking curved surfaces. With a 200 mm measuring range, the instrument fits the Standard class for workshop use, offering the best compromise between reach and rigidity for common components. The 0.05 mm vernier resolution corresponds to the typical analogue industry standard for robust repeatable measurements and clear layout lines. Built for everyday workshop durability Robustness is central to the design: the body is made from stainless steel with a matt chrome finish, providing corrosion resistance and a low-reflective surface for comfortable use under workshop lighting. A positive locking screw secures the slider to maintain set positions during marking. The solid construction, combined with a modest weight, makes handling straightforward while resisting the knocks of daily use. Protective transport in a case preserves calibration and tip condition during storage and movement between job sites. Practical handling, simple maintenance Reading and marking are kept efficient through the analogue vernier system, which avoids battery dependence and simplifies long-term maintenance. Replacing the scribing tip is a straightforward procedure that restores marking performance without replacing the whole instrument, reducing lifecycle costs and waste. The straightforward mechanical design means familiar operation for machinists and technicians, with little training required to achieve accurate, repeatable layout work. For durable, precise marking in the workshop, choose the Metav IndustryLine Scribing Caliper M201.151 — contact Metav Werkzeuge in Emmerich for purchasing or technical consultation via info@metav-werkzeuge.com or +49 2822 7131930 Technical Data Article number: M201.151 GTIN: 4054469100777 Manufacturer: Metav IndustryLine Facts Measuring range: 0–200 mm Resolution: 0.05 mm Scale type: analogue vernier Weight: 0.2 kg Special features Material: stainless steel, matt chrome-plated Replaceable carbide scribing tip Roller marking function Locking device (fixing screw) Delivery: protective case FAQ How precise is the marking made with this caliper? The scribing caliper delivers a vernier resolution of 0.05 mm, suitable for standard workshop measurements and accurate layout marking with repeatable results. Can the scribing tip be replaced when worn? Yes, the instrument features a replaceable carbide scribing tip, allowing simple renewal of the marking point without replacing the whole caliper. Is this caliper robust enough for daily shop use? The tool is made from stainless steel with a matt chrome finish and a locking screw, and it is supplied in a protective case to withstand everyday handling in the workshop. Which measuring range category does this instrument belong to? With a maximum range of 200 mm, the caliper falls into the Standard category (100–300 mm), offering a balance of reach and stiffness for general machine‑shop tasks. Is an ISO 17025 calibration certificate supplied with the instrument? No ISO 17025 certificate is specified for this item; it is supplied as a standard factory instrument. If an accredited calibration certificate is required, please request details before purchase. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
200mm Scriber Gauge Aluminium, 0.05mm Graduation, Hardened Scoring Edge, Black Anodised, Supplied in Case - Metav IndustryLine
Take advantage of a lightweight, anodised aluminium construction combined with a hardened marking edge and a fine 0.05 mm nominal tolerance for precise, repeatable layout work; order directly via Metav Werkzeuge or contact the consultants for application advice. Marking Gauge AL 200 mm (M201.191.AL) – Anodised aluminium, 0.05 mm tolerance A compact, metric marking gauge, the Marking Gauge AL 200 mm provides reliable scribing and layout capability for general workshop and metalworking tasks with a hardened scribing edge and millimetre scale Anodised aluminium body, hardened scribing edge Metric mm scale for precise layout 0.05 mm nominal tolerance Supplied in protective transport case Precision layout for everyday workshop tasks This marking gauge delivers a measured balance between reach and stiffness: the 0–200 mm range places it squarely in the standard measuring category favoured in machine and metal workshops. The device is specified with a 0.05 mm nominal tolerance, making it suitable for routine layout where clear, repeatable scribed lines are required. The integrated metric scale simplifies direct reading and alignment, reducing setup time on jigs and workpieces and supporting efficient process flow in small-series production. Robust materials that support repeatable scribing Constructed from anodised aluminium, the tool remains lightweight while resisting corrosion and abrasion; this aids manoeuvrability at the bench and reduces operator fatigue during repeated use. The hardened marking edge is specified to withstand repeated contact with scribing surfaces, ensuring consistent line definition over time. Supplied in a protective transport case, the instrument is protected in transit and storage, preserving calibration and edge integrity for reliable service life. Clear handling and workplace benefits The analogue mm-scale and straightforward clamping mechanism enable fast adjustments without electronics, ideal for harsh shop-floor environments or where simplicity and immediacy matter. As a non-digital layout instrument it requires no batteries and remains serviceable with minimal maintenance. The combination of low weight and solid profile yields repeatable results when marking out components, fixtures or assemblies, supporting quality assurance routines and reducing downstream fitting work. Contact Metav Werkzeuge today for tailored advice on using the Marking Gauge AL 200 mm and to arrange supply from our Emmerich facility. Technical data Article number / SKU: M201.191.AL GTIN: 4054469164533 Category: Marking tools (Anreisszeuge) Description: Marking gauge AL 200 mm, accuracy 0.05 mm, anodised black aluminium Facts Measuring range: 0–200 mm Nominal tolerance / accuracy: 0.05 mm Weight: 0.5 kg Tariff number: 90173000 Special features Material: aluminium alloy Finish: black anodised Marking edge: hardened Scale: mm-scale (metric) Operation: analogue Delivery: protective transport case FAQ What measuring range does this marking gauge cover? The marking gauge covers a measuring range of 0–200 mm; the Marking Gauge AL 200 mm from Metav IndustryLine is therefore classified in the standard workshop range. Is the scribing edge durable for repeated use on metal? Yes, the tool features a hardened marking edge which ensures the Marking Gauge AL 200 mm maintains clear scribed lines during repeated layout tasks. Does the product come with a protective case? The instrument is supplied in a protective transport case, so the Marking Gauge AL 200 mm is delivered ready for safe storage and transit. Who supplies this marking gauge and where can technical advice be obtained? This marking gauge is supplied by Metav IndustryLine; for technical advice and application guidance contact Metav Werkzeuge GmbH (see manufacturer details below) Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
200mm Steel Rule Flexible Laser-etched Scale 1/2mm Division, Stainless Spring Steel - TECWERK
Take advantage of a compact measuring solution that combines a 200 mm working length, flexible stainless spring steel construction and a clear mm/½ mm division for reliable workshop layout and quick checks; order directly via Metav Werkzeuge or consult the team for specification support. TECWERK Steel Scale L 200 mm — stainless, flexible with mm/½ mm graduation A TECWERK steel scale for precise linear measurement in workshop and maintenance applications, featuring a laser-etched scale on flexible stainless spring steel for durable, easy-to-read graduations. 200 mm measurement length Laser-etched scale for durable markings Flexible stainless spring steel construction Division in mm and ½ mm Reliable markings for repeatable results The laser-etched scale ensures durable markings that remain legible after repeated use and light handling. With a clear mm/½ mm division, the measuring strip provides straightforward increments suitable for layout tasks, inspection pre-checks and routine measurements on production parts. The compact 200 mm length delivers a balance between portability and usable measuring range, allowing rapid comparisons and visual checks without the need for larger instruments. Laser etching is a permanent method that resists abrasion; this reduces the need for frequent replacement and supports consistent measurement outcomes. Flexible design for diverse workshop tasks Manufactured from stainless spring steel, the measuring strip bends slightly to conform to curved surfaces while retaining spring-back resilience. The 13 x 0.5 mm cross-section keeps the scale slim enough for tight spaces and robust enough for everyday handling. Flexibility allows the strip to be used on cylindrical parts, pipework and profiles where rigid rulers are impractical, while the stainless composition supports corrosion resistance in damp shop environments. This combination of materials and form reduces handling time and improves adaptability across maintenance, fabrication and assembly tasks. Inspection-ready and quality-aware Marked as inspection required, this measuring device is suitable for workflows that demand traceability and documented checks. The construction and clear divisions make routine verification straightforward, supporting internal quality procedures or compliance checks. An inspection regime ensures that the measuring tool remains within expected tolerances and that any wear or damage is identified early, thereby maintaining measurement confidence on the shop floor and supporting process reliability. Practical handling and storage benefits The slim profile and compact length make the scale easy to stow in tool chests, pockets or instrument cases, providing fast access during set-up or servicing tasks. Durable laser-etched markings reduce misreads under workshop lighting, while the flexible strip is resistant to kinking when handled correctly. For operational efficiency, a single-piece packing unit ensures immediate availability for individual workstations or service kits. The straightforward format supports rapid measurement without the complexity of digital instruments where analogue checks are preferred. For flexible, inspection-ready measuring equipment from TECWERK, contact Metav Werkzeuge for ordering and technical advice at info@metav-werkzeuge.com or call +49 2822 7131930 to ensure the correct specification for the intended application. Technical data Article number: 2000858761NW Label: Steel scale L 200 mm stainless flexible division B = mm/1/2 mm TECWERK Manufacturer: TECWERK Product type: Steel scale UID: 2000858761NW Facts Length: 200 mm Cross-section: 13 x 0.5 mm Packing unit: 1 Special features Laser-etched scale Flexible execution Stainless spring steel Division: mm / ½ mm Inspection required: yes FAQ Is the scale suitable for measuring curved or cylindrical surfaces? Yes. The flexible stainless spring steel construction allows the scale to follow slight curves and cylindrical surfaces for layout and quick measurements. How precise are the graduations on the scale? The laser-etched divisions provide clear mm and ½ mm increments suitable for workshop layout and routine checks, with permanent markings that resist wear. Does this item require inspection or calibration? Yes. The product is marked as inspection required, and periodic checks are recommended to ensure continued accuracy and compliance with internal quality procedures. Are the markings durable under frequent use? The laser-etched scale ensures long-lasting, legible markings that withstand normal workshop abrasion and handling. Can the scale be stored in a tool chest without damage? The slim 13 x 0.5 mm profile and spring steel construction make the strip compact for storage; proper placement prevents kinks and prolongs service life. Manufacturer / Responsible: NORDWEST Handel AG, Robert-Schuman-Straße 17, 44263 Dortmund
200x150 mm Centering Square Matt Chrome Finish 0.6 kg - Metav IndustryLine
Take advantage of the combination of robust tool‑steel construction, a matt‑chrome reading surface and compact dimensions for reliable centring and clear scribing lines; order directly via Metav Werkzeuge or consult our advisors for application guidance. Centring Square M214.172 — Tool‑steel centring angle, matt chrome finish, 200 × 150 mm (Metav IndustryLine) The Centring Square M214.172 is a workshop scribing and alignment tool for layout and centring tasks in metalworking and machine setup, designed for robust everyday use Tool steel construction with matt chrome finish Clear mm graduation for precise marking Compact 200 × 150 mm format for bench use Suitable for centring shafts up to Ø220 mm Precise alignment for layout and setup The M214.172 combines a 200 × 150 mm profile with a finely finished matt chrome surface to provide a consistently legible mm graduation for scribing and layout work. The solid tool steel body delivers the stiffness needed to maintain a true edge during repetitive transfers, which reduces rework and supports faster set‑up times in production. For workshop technicians this means fewer adjustments and a clear, measurable basis for subsequent machining operations. Built for workshop durability and repeatability A hardened tool‑steel construction together with rust‑protected finishing ensures longevity under daily use. The matt chrome readout resists glare, so the graduation remains visible under different lighting conditions and during extended shifts. This durability translates into lower tool turnover and predictable measurement behaviour, improving process stability in assembly and fixture preparation. The compact format makes it easy to stow with other layout gauges while retaining the rigidity expected from a bench scribing instrument. Compatibility and practical handling The centring angle is engineered for practical handling: its format is suitable for marking and centring components, including shafts up to Ø220 mm, making it a flexible choice for turning‑shop routines and on‑machine layout. The pronounced edges provide a reliable datum for scribes and centre punches, while the balanced dimensions support single‑hand placement on small to medium workpieces. Clear graduations facilitate quick comparisons and help maintain a consistent workflow between marking and machining stages. For reliable centring and clear workshop layout, request the Metav IndustryLine M214.172 from Metav Werkzeuge or speak with our Emmerich team for specification advice and fast dispatch Technical data Article number: M214.172 GTIN: 4054469107004 Tariff number: 90172039 Facts Dimensions: 200 × 150 mm Suitable for shaft centring: up to Ø220 mm Category: Scribing/centring tool Special features Material: tool steel, rust protected Finish: matt chrome reading surface Application: workshop scribing, centring and layout Brand: Metav IndustryLine FAQ What materials is the M214.172 suitable for marking and centring? The M214.172 centring square is made from tool steel and is intended for layout on typical workshop materials such as steel and aluminium, providing a firm datum for punches and scribes. Is the mm graduation easy to read under workshop lighting? Yes, the matt chrome finish on the M214.172 reduces reflections and keeps the mm graduation clearly legible for fast and accurate marking. Can the centring square be used to centre shafts and cylindrical parts? The centring square is suitable for centring and scribing work and is specified for use with shafts up to Ø220 mm, assisting in quick alignment for turning and inspection tasks. Does the tool require special storage or maintenance? Routine care for the M214.172 consists of keeping the tool dry and lightly oiled to maintain the rust‑protected surface; the robust tool‑steel construction minimises the need for frequent maintenance. Which workshop applications benefit most from this centring angle? The M214.172 is especially useful for layout, centre‑punch transfer and fixture checking in general metalworking, lathe set‑up and assembly preparation. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
Precision marking that speeds up workshop tasks
Marking tools are the foundation of accurate fabrication and repeatable setup in industrial workshops. From scribing parallel lines on metal to laying out joinery on timber, the right marking tools ensure cuts, drills and mill passes start from a clear, reliable reference.
How these tools perform on the shop floor
A typical set of marking tools includes the scriber, the scriber needle, the precision caliper and the marking gauge. Each instrument serves a defined purpose: the scriber and scriber needle create fine guide lines for drilling and milling; the precision caliper measures and transfers exact distances for internal and external features; the marking gauge produces parallel lines on wood and other sheet materials. Used correctly, these instruments reduce rework by turning layout into a measurable, repeatable process.
Practical benefits that matter in production
- Improved accuracy for millimetre work, enabling tighter tolerances and more first-pass success.
- Reduced setup time through repeatable marking and rapid transfer of dimensions.
- Versatility across materials — suitable for wood, metal and plastics.
- Ease of use: simple handling of the scriber needle and intuitive adjustment on the precision caliper speeds routine tasks.
- Better quality control: clear, durable scribed lines act as unambiguous guides during cutting, drilling and finishing.
Why Metav is the sensible sourcing partner
Metav stands for democratising precision. As a precision partner with decades of experience, Metav supplies workshop-grade marking tools from its Emmerich-based quality hub, combining a wide range with consistent quality control. With more than 48,000 customers and a portfolio exceeding 250,000 products, Metav offers reliable availability and expert advice, making it a practical choice for procurement managers and workshop professionals seeking a single dependable supplier.
Summary
Well-chosen marking tools — including the scriber, scriber needle, precision caliper and marking gauge — turn layout into a fast, accurate and repeatable step in every production process, raising throughput and reducing scrap.
FAQ
What is the difference between a scriber and a scriber needle?
A scriber produces continuous guide lines for edges and profiles, while a scriber needle creates single, fine marks or narrow lines that serve as precise reference points for drilling or aligning operations.
When should I use a precision caliper for marking?
Use a precision caliper whenever millimetre-accurate distances must be transferred directly to the workpiece, for both internal and external features; it is particularly useful in machine shops and metalworking where exact offsets are required.
Are marking gauges suitable for metalwork as well as woodworking?
A marking gauge is primarily designed for wood, where its sharp fence and beam produce clear parallel lines; for metal, the scriber and scriber needle are generally preferred because they provide the finer, more durable scribed lines needed for machining.
How do marking tools improve production efficiency?
By providing clear, repeatable layout references, marking tools reduce measurement errors and setup iterations, which shortens cycle times and increases first-pass yield on parts.
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com